CATHODE RAY TOMES

Mr Do's Wild Ride

Mr. Do's Wild Ride (Universal, 1984) · Manual · 26 pages · 23 sections · original scan

Page 1

UNIVERSAL.

Page 2

WARNING:

THIS EQUIPMENT GENERATES AND USES RADIO FREQUENCY ENERGY

AND IF NOT INSTALLED AND USED PROPERLY, I.E., IN STRICT ACCORDANCE WITH THE INSTRUCTIONS MANUAL, MAY CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS. IT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A COMPUTING

DEVICE PURSUANT TO SUBPART J OF PART 15 OF FCC RULES, WHICH ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST SUCH

INTERFERENCE WHEN OPERATED IN A COMMERCIAL ENVIRONMENT.

OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY

TO CAUSE INTERFERENCE IN WHICH CASE THE USER AT HIS OWN

EXPENSE WILL BE REQUIRED TO TAKE WHATEVER MEASURES MAY

BE REQUIRED TO CORRECT THE INTERFERENCE.

UNIVERSAL

This documentation provides standard information. Universal reserves the right to change without notice.

Page 3

CONTENTS

Introduction . . Parts List ............4 Cabinet Requirements .... Control Panel Installation. . Wiring Installation ...... F.C.C. Requirements

  • How to Play............ Il. Various Option Settings .. Ill. How to conduct self-testing . IV. Main circuit board IC location and parts list .............0:-es eee eee eee 6-7

REFERENCE DRAWINGS

Fig. 1 Wiring Harness Pin Assignment Fig. 2 Modification For Separate Sync Outputs .. Fig. 3 Control Panel Accessories and Layout .. Fig. 4 Sound Amplifier Diagram .............- 00s eee scene eee een eee

Page 4

UNIVERSAL

UNIVERSAL U.S.A., INC. INTRODUCES

MR. DO’S WILD RIDE

Mr. Do’s Wild Ride is manufactured and marketed as a conversion for coin-operated

video games. This manual is designed for the use, maintainance and installation of

this product.

Installation, maintainance or repair should only be attempted by qualified service

personel.

Technical assistance is available by calling:

1-800-538-7548 Outside California.

1-408-727-4591 Inside California.

172247 Telex

Page 5

Upon receipt of your Universal U.S.A. conversion kit be sure to verify that all contents are complete and free from defects or damage. Notify your distributor of any discrepansies in the kit as soon as possible.

Your Mr. Do’s Wild Ride Conversion Kit includes:

A) 1- Mr. Do’s Wild Ride P.C.B. (Contained in an R.F. shield). UNIVERSAL PART #02-10022-00 (06-10100-00)

B) 1 - Audio-amplifier P.C.B. UNIVERSAL PART #02-10100-00

C) 1- Main wiring harness assembly. UNIVERSAL PART #03-10100-00

D) 1 - 4/8 way joystick assembly. UNIVERSAL PART #04-05000-00

E) 4- Push buttons (Complete with housing). UNIVERSAL PART #04-05111-00/04-05202-00

F) 1-24" x 9” clear control panel plexi glass. UNIVERSAL PART #05-00005-00

G) 1 - Set of control panel decals. UNIVERSAL PART #05-22107-00

H) 1 - Policarbonate control panel overlay. UNIVERSAL PART #05-22105-00

!)_ 1- Mr. Do’s Wild Ride Marquis (Title) plex. UNIVERSAL PART #05-22000-00

J) 2- Mr. Do's Wild Ride side decals. UNIVERSAL PART #05-22120-00

K) 1 - Mr. Do’s Wild Ride instruction decal. UNIVERSAL PART #05-22110-00

lL) 1- Mr. Do’s Wild Ride license sticker.

Page 6

Cabinet Requirements

The Mr. Do's Wild Ride Conversion Kit can be installed into any standard cabinet (Upright or cocktail). The game is designed to display on any standard horizontally mounted, color (R.G.B.), rastorscan monitor.

Many cabinets allow for the repositioning of monitors from verticle to horizontal mountings. Repositioning of a verticle mounted monitor is a delicate, if not cumbersome operation and extreme care should be exercised in handling any monitor. It is recommended that the installation of the Mr. Do's Wild Ride Conversion Kit be attempted only on those cabinets inwhich monitors are presently mounted horizontally or in such cabinets, where by design facilitates the repositioning or mounting of monitors to be easily interchangeable. It is not recommended that cabinets be physically altered or any reconstruction of cabinets be done by anyone other than those qualified and having the appropriate facilities to conduct such operations.

The Mr. Do's Wild Ride P.C.B. will require regulated voltages of +5 and +12 VDC. Most standard power supplies will provide these voltages, therefore the replacement of existing power supplies may not be necessary. Along with the monitor and power supply; the control panel, speaker and coin door need to be retained from the existing cabinet.

Control Panel Installation

Parts furnished with the Mr. Do's Wild Ride conversion kit for the control panel modification are pictured and listed on page 10, diagram A; as well as an installation layout.

Begin removing the existing controls and graphics, then prepare the surface by cleaning and removing any foreign material and debris. Take note of the existing holes in the panel to determine placement of the new controls.

NOTE: Repositioning and drilling holes to install the new controls on the exisiting control panel may be necessary and require the use of power tools. In the event such tools are needed exercise extreme caution. If assistance is required, contact a local Universal U.S.A. Distributor.

Apply the polycarbonite overlay to the top of the control panel and trim away any excess material around the edges and holes to be used for the new controls. Attach the indication decals (1.E., joystick, "Run", 1 player and 2 player) on top of the overlay next to the corresponding holes.

Page 7

If needed or desired, measure and cut the clear plexi glass furnished with the kit to fit the existing control panel. Drill holes for the controls at 1 1/8 inches in diameter to accommodate the joystick and buttons where needed. Be sure to file or sand away any rough corners around the edges of the plexi glass.

Wiring Installation

All wiring terminations and connections for the Mr. Do's Wild Ride conversion kit are in the secondary or low voltage circuit (Less than 42 VDC).

Electrical Cautions: -Never attempt installation, connection, or electrical terminations with power applied to the unit. *Never disconnect the Printed Circuit Board(s) with power applied. ‘Never replace any components with anything other than exact replacement parts.

Begin the wiring process by removing the existing P.C.B.(s) and wiring harness(s). Physically secure the Mr. Do's Wild Ride P.C.B. and audio amplifier P.C.B. to the inside of the cabinet. Pin assignment and termination points of the harness assembly are provided on page 8 of the manual.

Termination of the wiring harness can be seperated into five

  • basic catagories.
  • Power Inputs: +5 VDC, +12 VDC and Ground
  • Video Outputs: Red, Green, Blue, Video Ground and Sync.
  • Player Controls: Up, Down, Left, Right, Run, Ist and 2nd Player Start
  • Coin Door: Left Coin, Right Coin, Slam Switch and +5 VDC (Coin Meter)
  • Audio Output: Speaker
  • Power Inputs: Termination of the voltage leads is probably the most critical and fundamental process of the installation. Extreme caution should be taken to insure correct terminations and proper voltages. The voltage input lines are distinguishable, as 18 gauge wire is used for each. (+5 VDC-Orange at pin #3, +12 VDC-Red at pin #8 and Ground-Black at pin #1). Before proceeding, verify that each input voltage is correct and at the proper designated pin assignment of the P.C.B. connector.

-iv-

Page 8
  • Video Outputs: Connections can be made by terminating the Red (Pin Z), Green (Pin A), Blue (Pin B) and Video Ground (Pin E) to the corresponding inputs of the monitor. It connect the sync output(s), first determide what inputs are needed by monitor. The composit sync White wire at (Pin T) can be terminated to the composit sync input of the monitor, if applicable. Mr. Do's Wild Ride will generate a negative composit sync. In most cases where negative horizontal and verticle sync is needed, terminations can be made by connecting the White composit sync line to both negative H & V inputs of the monitor.

If a positive signal is needed, see modification on page 9 or contact your local distributor to obtain a Universal 8300- TV-B Video P.C.B. (This assembly can be used to modify sync signals).

NOTE: The leads at pins #5 (Orange) and #6 (Brown) are designated for verticle and horizontal sync outputs and are needed only for the modification on page 9.

If the display appears on the screen "Upside-Down" the display can be turned by a dip-switch setting. (Dip-switch A-SW5 - See option settings on page 2).

  • Player Control Inputs: Player control inputs will be connected at the control panel. All the 1st player controls and player select lines on the wiring harness assembly are terminated with "Quick-Disconnects" which mate with the leaf switches of the controls furnished with the conversion kit.

The joystick terminations can be made by connecting the designated wires to corresponding switches on the 8-way joystick supplied in the kit.

"Up" - Blue wire at pin #13 "Down" - Yellow wire at pin #17 "Left" - Purple wire at pin #19 "Right" - Brown wire at pin #15

The remaining wires for the action and player select buttons are to be terminated as follows:

"Run" - Red wire at pin #22 "1 Player" - Orange wire at pin #21 "2 Player" - Green wire at pin #Y

-v-

Page 9

The ground lead(s) for the controls are terminated and “daisy-chained" with eight (8) disconnects to be connected to the other contact of each leaf switch on the control panel.

The 2nd player control lines are unterminated and are only needed for a cocktail table installation, where two sets of controls are needed. Pin assignments can be found on page 8.

  • Coin Door & Inputs: Wiring for the coin inputs can be accomplished by following either of the diagrams on the bottom of page 8. Seperate coin inputs are provided on pins #24 and #25 to allow for the selection of independent coin chute pricing (For options on price selection see page 2 - dip-switch B).
  • Audio Outputs: Begin by soldering the speaker lines to terminals Sl (-) and S2 (+) on the audio amplifier P.C.B., then connect the audio plug on the harness assembly (White 4 pin molex) into the socket (p1-4) on the amplifier unit.
NOTE: To avoid audio distortion, verify that the voltage to the amplifier is regulated at +12 Volts DC.

F.C.C. Warning:

"This equipment generates and uses radio frequency energy and if not installed and used properly, I.E., In strict accordance with the instructions manual may cause harmful interference to radio communications. It has been tested and found to comply with the limits for a CLASS A computing device pursuant to SUBPART J OF PART 15 OF F.C.C. RULES, which are designed to provide reasonable protection against such interference when operated in a commercial environment."

"Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.”

Mr. Do's Wild Ride P.C.B. is enclosed in a metal R.F. shield to meet the F.C.C. requirements stated above.

To comply with the ruling it is imparative that the R.F. shield is installed properly. After mounting, make sure that the cage is GROUNDED. With an Ohm meter, conduct a continuaty test between the shield and ground, to verify proper installation. Enclosed in the conversion kit is an F.C.C. Warning Sticker. This decal MUST be placed and maintained on the exterior of the cabinet.

Under NO circumstances should this equipment be operated without the Printed Circuit Board properly installed in the R.F. shielding

-vi-

Page 10

UNIVER

|. HOW TO PLAY

x Advance to the GOAL by way of the coaster lane.

  • Dodge the oncoming COASTERS by climbing the LADDERS along the coaster lane. When climbing the LADDERS be careful of COASTERS on the overhead lanes.
  • Pass difficult and dangerous spots quickly by pressing the RUN button! (Note: When using the RUN button, bonus points will decrease rapidly.)
  • Change both TARGETS at the goal by picking up the FRUIT at the top of the LADDERS.
  • Make © (%) @ (R) @ by picking up the letters as they appear at the GOAL and receive another Mr. DO!
  • Ifyou reach the GOAL when the DIAMOND ( <> ) appears, you receive a REPLAY (optional see Dip Switch Settings)
  • Bonus points are fixed at 4500 and begin to decrease when game play starts. The number of points remaining when the GOAL is reached is added to the score (AMr. Dol is lost when the number of BONUS points run out)

{ POINTS )

Coaster

Page 11

e Dip Switch A

UNIVERSAL

I]. VARIOUS OPTIONAL SETTINGS

DESCRIPTIONS OF DIP SWITCHES

  • Number of Mr. Do! Given (SW1)
  • Difficulty of the Games (SW7, 8)
No. of Mr. Do!swiDifficultysw7
e3OFFe1 (Beginner)OFF
5ON2OFF
.3ON
2. Special (SW2)4 (Advanced)ON
Given or notTsw2]
eGivenOFF

Not ON

  • Game Style (SW3) © Factory Settings

Style Sw3 Table OFF

eUprightON

eee e Positions of Dip Switches

  • Difficulty of EXTRA (SW4) Difficulty Sw4
eEasyOFFMAIN CIRCUIT BOARD

Difficult ON

  • Screen Direction (SW5) “|

Direction Sws Dip SWA Dip SWB

eForwardOFFa
[revereONpees || ee

OFF 1 =

  • Automatic Renewal of Screen (SW6)
[Automatic renewalSW6
eMadeOFF

Not made ON

© Dip Switch B (Coin & Credit)

Goin | creditLeft-side chuteRight-side chuteStandard and Custom Price Settings
‘oin | Credit[oa 7 sw2 | sw3 | swa | sws | swe | sw7 | swe..
e|17 | ore | Orr | OFF | OFF | OFF | OFF | OFF | OFFThe game price set by a combina-
12. | orr | orr | ofr | ON | OFF | OFF | OFF | ONtion of dip SWs is displayed on the
73.|orr | OFF | ON | OFF | OFF | OFF | ON | OFFmonitor when coin credit is 0.
14_|orr | orF | ON | ON | OFF | OFF | ON | ON,;
1S|OFF | ON | OFF | OFF | OFF | ON | OFF | OFFa) When the settings for right
27bore | on | orf | on | OFF | ON | OFF | ONand left chutes are the same,
23 | oFF | on | on | orF | OFF | ON | ON | OFF“1 coin — iu credit”, ‘2 coins
31 | ore | on | on | on | off | on | ON | ON— 3 credits’, etc. are dis-
32 | ON | ofr | OFF | OFF | ON | OFF | OFF | OFFplayed.
41ON | OFF | OFF | ON | ON | OFF | OFF | ON..
71 | on | orF|_on | ofr | on | oFF | on | OFFb) When the settings for right
17onTorr | oN | on | on | OFF|_ON | ONand left chutes are provided
17|on | on | oFF | OFF | ON | ON | OFF | OFFdifferently, their respective
1qon | on | OFF | ON [| ON | ON | OFF | ONcontents can be displayed.

1 7 | on | on | on | OFF | on | ON | ON | OFF

Free playONONONONONONONon]
Page 12

UNIVER

MR.DO’S WILD RIDE has a self-test which locates any abnormalities within the circuitry should they occur. To enter the diagnostic self-test, turn power ON while depressing the 1 PLAYER START button.

A. C.P.U, and MEMORY TEST

*CRT displays:

CPU -1 location S1 RAM OK location H1, E1, and F1 ROM 1 OK location P1 ROM 2 OK location N1 ROM 3 OK location L1 ROM 4 OK location K1

*During the RAM test a sequence of high, middle, and low pitched tones (twelve each) should be heard. Upon passing and completion of the RAM test the tones should stop and the test should continue.

  • CRT displays:

CPU - 2 location L7 RAM OK location P7 ROM OK location N7

Page 13

UNIVERSA

B. Color Sample Test:

This segment of the self-test is to aid in adjusting and identifying the color and intensity of the display to exit this portion of the diagnostic test, depress both 1 player and 2 player start buttons simotainiously.

*CRT displays:

Color Sample Test

("Red")Rooo0oo0oo0da* 0 Thru 7 display varying
("Green")G.bDoooaodintensities of each color,
("Blue")B.oo0ag0agodgono0 being Black or the dark-
("White")wW.ooo0oa0ogon0est to 7 being the lightest.

01234567

C, Switch Test: Switch names are displayed on the left side of the screen, while input conditions will be displayed on the right side. When the switch is ON, “0” is displayed for input, and when it is OFF, ‘’1” is displayed. Conduct test while turning each switch ON-OFF — the test will advance to the next step after

a minute.

Switch name Input condition COIN LEFT COIN RIGHT PAUSE SERVICE TEST TILT Switch name Input condition 2P DOWN 1 LEFT LLiLI tty

4P START NOT USED 4P JUMP. FIRE NOT USED NOT USED. “0” will appear when pushing the pushbutton on the 1st player's side. i

2P START ii

Page 14

URIVERSA

Dip switch A | 1 | o/;1}]1)0 = B 1 1 1

D. TV Monitor Test:

A cross hatch pattern will appear on the screen. Monitor adjustments can be made at this time.

Self-testing will stop at this point. Turn power ON again when you want to resume game play or execute the self-test again.

@ In case you have found any abnormality as a result of the self-test, contact your local Universal U.S.A. Distributor.

Page 15

UNIVERSAL

IV. MAIN CIRCUIT BOARD IC LOCATION AND PARTS LIST

a ahatatdalctelaleleislaieneta al

e 3 Hy

: 33 fl of fo}

| < ® vo @ ww uw rr 3 ¥ a | Fig. 1 Main Circuit Board IC Location

Page 16

UNIVER

[1] Integrated Circuit 2] Capacitors

Item No.Q'tyDescriptionRatingQ'tyDescription
74LS OON2 | TT5OPF50V2Ceramic Capacitor|
TALS 011"220PF50V1"
74LS 044"390PF50V3
74LS 081“0,014 F50V5"
TALS 202“0.1uF 12V25“
TALS 271“4.7uF25V1ES Capacitor
T4LS 321"TOuF16V7”
74LsS 745"47uF 16V2”
74LS 867"470uF 16V1”
74LS1383T000uF 16V1Gi
74LS1393|"
74LS1576"
74LS1613"
742442E
74LS2452[3] Registors
cera4”RatingQ'tyDescription
a6"2221Carbon Solid
74LS2833gTo0917
74LS3731"0083=
74LS374433003
74ALSO4N1"30007
74ALS081"470227
74S374N1232022-
Z80A3 | NMOS CPU (4MHz)1KQ2
2764-3008 | NMOS 64k bits EP ROMBK17
(Access 300nsec)10KQ1y
27128-3002 | NMOS 128K bits ROMSOKG.5x

(Access 300 nsec)

N82S1472 | 4096 bits Fuse ROM2aKo:4”
Ts41e4200 | 16 | 64K DRAM30Ka1_
MBB8128-1505 | NMOS 16K bits Static RAM100KS28”
(Access 150nsec)120K24a
MB8128-1001 [ NMOS 16K bits Static RAM220K21a
(Access 100nsec)510KQ2.1”
CF37201N1 | Custom Function330 x 83Resistor Array
NE5S61 | Timer1K x82“
LM342N1_|Audio AmplifierLiokxs| 2”|
SN76489AN4Programable Sound Generator.

Tms1o25NacL | 2 | CMOS 4] Mise

HD46505SP.1CRTCNameQ'tyDescription
10D14 | DiodeDip SW28 Elements Switch Array
[-va7e0s[1_[ResutatorX tal19.828MHz:
”14.000MHz
20P2IC Socket
This drawing provides standard information.|28P10"

Universal reserves the right to change without notice.

Page 17

UNIVERSAL

Fig-1

MR. DO’S WILD RIDE HARNESS PIN ASSIGNMENT

SOLDER SIDE COMPONENT SIDE

USECOLORCOLOR

2 Bik. eas CLAYER GND --=- Blk. GND (TO POWER SUPPLY)

COIN sw hee or] GND sik. | 8-2 | Blk. GND (1st PLAYER & SELECT Sw) \ Ora, +8v (TO POWER SUPPLY)

AUDIO AMP BOARD\Ore, +8v (COIN COUNTER)

1 Ora, VERT. SYNC

i ) TO MONITOR

3 Brn, HOR, SYNC

Red +12v (TO POWER SUPPLY)

stam sw Gin. TN | 12 |

2nd PLAYER UPBlueBlue 1st PLAYER UP

Brn,

FOR2nd PLAYER RIGHTBrn, 1st PLAYER RIGHTUP RIGHT

Cc: TABLE JOYSTICK

2nd PLAYER DOWN Yel. Yel, 1st PLAYER DOWN

2nd PLAYER LEFT = Pur. Pur. 1st PLAYER LEFT

2 PLAYERS SELECTGrn.Ora. 1st PLAYER SELECT

VIDEO RED Red Red 1st PLAYER THROW

To VIDEO GREEN — Grn. Red 2nd PLAYER THROW (FOR C- TABLE)

MONITORVIDEO BLUEBlueYel. LEFT COIN SW/COUNTER

COMPOSIT SYNC Wht. Brn, RIGHT COIN SW/COUNTER

GND Bik.

NOTE:

CONNECTION FOR USE WITH COIN METER

R COIN SW CONNECTION FOR USE WITHOUT COIN METER

R COIN SW GND Ne COIN COUNTER «PIN #8)

CONNECT EITHER +5y EITHER ec

FIN #24 OR #25 (PIN#4) PIN #24 OR #25 nd +5v (PINE 4) NC.

GND (PIN#B)

NO

LCOIN SW

Page 18

Fina UNIVERSA

MODIFICATION FOR POSITIVE HORIZONTAL AND VERTICAL OUTPUT

CIE) tC]

472 %W

+VERT SYNC

+ VERT SYNC

YOLOIJNNOD Nid 9S

+HOR SYNC

  • BE SURE TO REMOVE COMP SYNC LINE WHEN INSTALLING THE POSITIVE INDEPENDANT SYNC LINES.
  • BEFORE ATTACHING THE JUMPER WIRE FOR THE POSITIVE HORIZONTAL SYNC SIGNAL TO PIN 6 OF THE CARD EDGE, ISOLATE PIN 6 BY CUTTING THE TRACE DIRECTLY BEHIND THE PAD.
Page 19

7 UNIVER

Control Panel Assessories And Layout

Diagram A.

A. Clear Plex B. Policarbonite Overlay C. Indication Decals D. 8-Way Joystick E. Buttons F. Pal Nuts G. Button Housings W/Leaf Switch

Player Controls Diagram B. ® ¥ 7 + | r=) Clear Plex fi

I : | | Indication Decals a @ oo

a = Overlay

Control Panel

Page 20

Fes UNIVERSAL

SOUND AMPLIFIER DIAGRAM AND PARTS LOCATION

470u/ 16x P4 P3 P2 PI

VRI: RV 16YP 10S B 1KQ

SOUND AMPLIFIER UNIT

Page 21
Scan of page 21

This page is a drawing, shown as the original scan.

Page 22

(¢ ON) wesberg snewayog pueog yinaig wey G “fly Ey esw | Ll flolele cle lolel-lele if oovs. i ANiL inven. xis ES aera Geer eLelete bck a tk cit aq ele Fi TPP PEPE oy EE “cok bleleLlo _— ovfe Ps i

Peep (oo (se RREEE fellate fale: 108 — 5 onenszoiswis 66 1955) | —> duvis 13838 Ms La aroguo 301AN3S publ aunKo. bie) caunio Ys | i ae = =

Page 23

UNIVERSAL

VII. BLOCK DIAGRAM

MsB ™ Liv

1.5K 15K 1.5K 1KB

sev 22K

GND Fig.6 Main Circuit Board Schematic Diagram (No. 4)

—~1- 2D+-{_Door sw. }+{__Main SW. + Transformer

Power Supply.

Start SW

Control Lever Main Board ——-+ m Video Signa!

Coin SW

Coin Counter Speaker

Fig. 7 Block Diagram

Page 24

UNIVERSAL

BLK a3 1 6% c

a81>= cine

%

p

“aux Z

soptx 3 Ho

dine \ 0 ¢ a

z¢7%

468058

2° é 3 nas

artBI3

cas

1249]1{4h2} 4} 9] 1]+3+ om

a wg |= Ns ss pens tm Qes °5

-T9SCROnE
5sissisisisfs|s
oss4ay
j-4

mas

M07

| 7]B20z

aka Aes ADRERERE ea fb epee vahshohe a Lal eu of

Saffa:
Act 24gob 373 > acs gtaHeeGreen
FENRIS]TPEoa) g [5 aoe
2riray pb ry|oe] % bio 36Dove
Onna&ddd]=‘ue
LeesEly|A2x
soe!00} Jala}alsielr) “) 00] yelalaisighzS
  • 400? x 3

Fig. 4 Main Circuit Board Schematic Diagram (No. 2)

Page 25

WILD RIDE

COPYRIGHT INFRINGEMENT POLICY

Universal U.S.A., Inc. holds the sole proprietary interest for the manufacture of the Mr. Do's Wild Ride game, and has registered a copyright and trademark with the United States Copyright Office.

Due to Mr. Do’s Wild Ride’s excellent earnings report, there may be those interested in illegally reproducing this game.

LET THERE BE NO MISTAKE! Universal U.S.A., Inc. will protect it’s proprietary rights by taking any and all legal action necessary against any person or company that manufactures, sells, distributes, and / or operates any game which violates these exclusive rights of the Mr. Do’s Wild Ride video game. Any violation whatsoever will be prosecuted to the fullest extent of the law.

Authenticity of any Mr. Do’s Wild Ride game can be verified by callin 1-(800) 538-7538 during regular business hours.

UNIVERSAL

Universal U.S.A., Inc. 3250 Victor Street (408) 727-4591 Santa Clara, CA 95050 TELEX: 172247

Page 26

Head Office: Universal Co., Ltd. 4-7-7, Nihonbashi Horidome-cho, Chuo-ku, Tokyo 103, Japan Phone: 03-661-6004, 6005 Cable: UNMANIF ACT Telex: J27348 (UNICO)

Universal U.S.A. inc. 3250 Victor Street, Santa Clara, California 95050, U.S.A. Phone: 408-727-4591-5 Telex: 172247 (UNI USA SNTA) Main Line of Business: Development, manufacture, sales, and export & import ot amusement machines

European Office 81 Tottenham Court Road, London W1A 1EY Phone: 01-631-1713 Telex: 892989. ELCOIN