CATHODE RAY TOMES

Asteroids Deluxe Signature Analysis

Asteroids (rev 4) (Atari, 1979) · Document · 9 pages · 26 sections · original scan

Page 1

ASTEROIDS DELUXE

SIGNATURE ANALYSIS

GUIDE

Page 2

Introduction

This guide is intended as an aid to troubleshooting the Asteroids Deluxe video game PCB. The Signature Analyzer used to produce this guide was an HP5004a. If it is found that the signatures hold up for other makes/models of Signature Analyzers then please let me know and I can add some kind of compatibility list to the document. Suggestions of any kind to improve this document are always welcome.

To get the most out of the guide you'll need

Signature Analyzer (HP5004a) Schematics for Asteroids Deluxe 6502 NOP card (See the separate document 6502NOP for instructions on how to build your own NOP card)

IC Clips

Some jumper wires (3 or 4 should be sufficient)

The scope of the guide is limited in that it will not enable you to fault find the entire PCB. It should, however, be good for the following sections of the PCB:

Address Bus Buffers, Address Decoding Circuitry, Clock Circuit, Program ROMs and Data Buffer, Vector Generator Address Selector, Vector Generator RAM Select, Vector Generator ROMs and the Vector Generator Data Buffer.

The Clock Circuit test is very limited. The reason being is that I much prefer to check the clock chain with a scope. If you want to figure out the signatures for the Clock Circuit then pass on the information and I'll include it in the document. If you want a detailed description of these sections (and more) please refer to the Asteroids Deluxe schematic / drawing package.

Using The Guide

For those of you who have used Atari Signature Analysis guides before then this should look familiar and there’s probably no need to read through this section. For the rest of you, here’s a quick run down. Every section should start with the settings for the Analyzer, something like this

A. SA Settings for xxxxx Test

ProbeTriggerICPinTest Pt.
Start+veC2-25
Stop-veC2-25
Clock-veC2-392
Page 3

The probe column refers to either the Start, Stop or Clock probes from the Signature Analyzer.

The trigger column sets up the Start/Stop/Clock buttons on the front of the Analyzer. I have used —ve to indicate the negative going edge of the pulse (or the falling edge). Ihave used +ve to indicate the positive going edge of the pulse (or the rising edge). The IC Pin column refers to the point where the appropriate probe should be attached. The Test Pt. column refers to an equivalent Test Point on the boards where the probe may be attached.

For example, in the example above the Start probe should be connected to pin 25 of IC C2. The Start button on the front of the Analyzer should be in the fully out position to indicate a positive going edge. Similarly, the Stop probe should be connected to the same IC/Pin as the Start probe but the Stop button on the Analyzer should be pressed in to indicate a negative going edge.

The section immediately following the set up procedure contains the signatures for that part of the test. The same structure for the Set Up was employed as explained below.

B. Signatures

Logic Probe — Signal Signature

On IC/Pin Name

C1-20 +5V 0003

C1-9 ABO UUUU

C1-12 ABI FFFF

Here, with the Analyzer probe on pin 20 of IC C1 you should get a reading of 0003. On pin 9 of IC Cl you should get a reading of UUUU. And so on.

A signature denoted by an (*) indicates that signature may be unstable. Try taking the signature with a 1Kohm resistor connected between the probe tip and +5V.

Down To Business

One of the things I like about this testing method is that you don’t need to have the PCB in the cabinet. If you prefer to work in the back of the cabinet then that’s fine. If you have a bench/test area with a +5V PSU (as I’m sure most of you have), then you can sit comfortably at the bench. Simply connect Ground (pins | and 22 on the edge connector) and +5V (pins 2 and 21 on the edge connector) to the PCB and you’re ready to start.

Just set up the Analyzer as indicated and start probing for those signatures. Always remember to have the Watchdog disabled as this will lead to permanently unstable signatures.

Page 4

What To Do When You Find An Incorrect Signature

If you find a signature that doesn’t match the guide, check your set up first. If your set up is OK then you’ll need to trace the fault. Rather than having a long winded ramble from me it would be better to look at the following link on Al Kossow’s page. If you haven’t already had a look at his site then I’d definitely recommend having a look as it’s a bit of a gold mine.

http://www.spies.com/arcade/TE/SigAnalNotes pdf

After you’ve had a look through the document then you should know enough to start tracing the fault. It should also give you a bit more information on Signature Analysis in general.

Some Common Faults

The two most common faults I’ve come across are bad sockets and shorted traces. During the Signature Analysis the bad socket problem is highlighted by the fact that the signatures are unstable. You may get some stable and some not. When you get unstable signatures whilst doing the ROM tests it does not necessarily indicate a bad ROM. Reseating the ROM or replacing the socket is usually a good place to start. The problem of shorted traces is usually down to something being dragged across the board. Sometimes they can be quite hard to see but Signature Analysis shows it up quite good.

Disclaimer

If you toast yourself, your house, your dog, your family or more importantly your video game, then it’s not my fault. You use the information contained in this guide at your own risk. Good luck.

Document Author Peter Fyfe

Email (Home) peter@bombjack .freeserve.co.uk

Email (Work) peter.fyfe@honeywell.com

6" February 2000

Page 5

** Tie the Watchdog Disable test point to ground **

  • Address Lines

A. SA Settings for Address Buffer Test

Probe

Start

Stop

Clock -ve

-ve

-ve

B. Signatures

Logic Probe

On IC/Pin

C1-20 Ccl-9 C1-12 C1-7 Cl-14 C1-5 C1-16 C1-3 C1-18

B1-18 B1-14

C2-23 C2-24 C2-25

Trigger

Signal

Name

+5V ABO IC Pin

C2-25 C2-25 C2-39 Test Pt.

Signature

0003

FFFF 8484 P763 1U5P 0356 U759 6F9A

7791 6321 37C5 6U28 4FCA 4868 9UP1 0001

  • Address Decoding

C. SA A. SA Settings for Address Decoder Test

Test Pt.

AF76 6913 13HP 3282 AH63 TAPA P508

3HO1 3H02

P933 UH4P A04H 86C1

Test Pt.

ProbeTriggerIC Pin
Start-veC2-25
Stop-veC2-25
Clock-veC2-39

Logic Probe — Signal On IC/Pin Name

E3-4 SINPO E3-5 SINP1 E3-6 OPTS E3-9 MEM E3-10 VMEM E3-11 E3-12 ZPAGE

D5-10 KYDCD C5-8

L2-4 ROMO L2-5 PROM1 L2-6 PROM2 L2-7 ROM3

Settings for Address Decoder Test

ProbeTriggerIC Pin
Start-veC2-25
Stop-veC2-25
Clock-veC3-14

6MHz

** Tie R/W test point to ground **

D. Signatures

On IC/Pin

DS-14

Name

+5V

OOUP

Page 6

DS5-4 E4-8 L5-1 L5-2 L5-3 L5-4 L5-5 L5-6 LS-7 L5-9

B8-13 B8-12 B8-11

** Remove jumper from R/W test point ** 0066 (*) TUTC DMAGO —-383U EAADDRL P759 WDCLR —-90P8 EXPLODE UAOP A43F EACONTROL USFA

AUDIO 81F6

NOISERESET 1A35

OOUP A43F DMARESET A43F

3..Watchdog Circuit

A. SA Settings for Watchdog Circuit Test

Probe Trigger ICPin Test Pt.

Start -ve

Stop -ve Clock -ve 2-25 2-25 C239 42

** Tie L5-12 to ground **

B. Signatures

Logic Probe

On IC/Pin

C5-14 C5-6 D4-6 D4-8 Signal Signature Name

+5V 0003 752C 0398 0000

** Remove jumper from L5-12 ** 4..Clock Circuit

A. SA Settings for Clock Circuit Test

Probe Trigger

Stop -ve Clock -ve

On IC/Pin

B3-6 B3-8 B3-10 Signal Name

3KHz 12KHz ICPin Test Pt.

2-25 2-25 C2-39 2

Signature

763H 8A4U, 9720

5 ROM And Data Lines

A. SA Settings for ROMO Test (D1)

Probe Trigger

Stop +ve Clock -ve

On IC/Pin

D1-24 D1-9 D1-10 D1-11 D1-13 D1-14 D1-15 D1-16 D1-17 Signal Name

+5V DBO DBI DB2 DB3 DB4 DBS DB6 DB7 ICPin Test Pt.

L2-4 L2-4 C2-39 92

Signature

826P 4869 995C FOAH UF20 AI7H 232H 4590 99P1

Page 7

C. SA Settings for ROM1 Test (E/F1)

Probe Trigger

Start -ve

Stop +ve Clock —-ve

D. Signatures

Logic Probe

On IC/Pin

E/F1-9 E/F1-10 E/F1-11 E/F1-13 E/F1-14 E/F1-15 E/F1-16 E/F1-17

Signal

Name

DBO DBI DB2 DB3 DB4 DBS DB6 DB7 IC Pin

L2-5 L2-5 C2-39 Test Pt.

Signature

UOF3 0UCU OCAS A391 TFT9 U77P H494 052H

E. SA Settings for ROM2 Test (F/H1)

Stop +ve Clock —-ve

F. Signatures

On IC/Pin

F/H1-9 F/H1-10 F/H1-11 F/H1-13 F/H1-14 F/H1-15 F/H1-16 F/H1-17

Name

DBO DBI DB2 DB3 DB4 DBS DB6 DB7 IC Pin

L2-6 L2-6 C2-39 Test Pt.

$2

P65C 6FHO 7C88 PC19 94HP CP77 4AF2 7P08 G. SA Settings for ROM3 Test (J1)

Stop +ve Clock —-ve

H. Signatures

Logic Probe — Signal On IC/Pin Name

J1-9 DBO J1-10 DBI J1-11 DB2 J1-13 DB3 J1-14 DB4 J1-15 DBS J1-16 DB6 J1-17 DB7

  • Data Buffer IC Pin

L2-7 L2-7 C2-39 Test Pt.

373U U96F 76U1 91PP 9P50 A126 10A0 F002

A. SA Settings for data buffer test.

Stop +ve Clock —-ve

B. Signatures

Logic Probe — Signal On IC/Pin Name

E2-18(19) DO E2-17(18) DI E2-16(17) D2 E2-15(16) D3 E2-14(15) D4 £2-13(14) D5 E2-12(13) D6 B2-11(12) D7 IC Pin

L2-7 L2-7 C2-39 Test Pt.

373U U96F 76U1 91PP 9P50 A126 10A0 FO02

Page 8

** The numbers in brackets are the pin assignments when an AM8304B is used as opposed to a 74LS245 Bok

  • Vector Generator Address

Selector

A. SA Settings for VG Address Sel Test

Probe Trigger

Start -ve

Stop -ve Clock —-ve

** Tie K2-1 to ground **

B Signatures

Logic Probe

On IC/Pin

K2-1 K2-4 K2-12

L2-10 L2-11 L2-12

F2-9 F2-7 F2-4 F2-12

H2-12 H2-4 H2-7 H2-9

J2-9 J2-12 J2-4 C2-25 C2-25 C2-39

Signal

Name

+5V AMI1 AM12

VROM2 VROM1

AMO AMI AM2 AM3

AM4 AMS AM6 AM7

AM8 AM9 AM10 IC Pin Test Pt.

$2

Signature

0003 6U28 4FCA

F501 P693 AA2A

FFFF 8484 P763

1U5P 0356 U759 6F9A

7791 6321 37C5

  • Vector Generator RAM

A. SA Settings for VG RAM Test

Probe

Start Stop Clock Trigger IC Pin

-ve C2-25 -ve C2-25 -ve C2-39

** Tie K2-1 to ground **

Logic Probe — Signal On IC/Pin

M4-3 M4-6

L4-4 Name Test Pt.

Signature

98H1 32U8

37C6

  • Vector Generator ROM

A. SA Settings for VG ROM 1 Test (R2)

Probe

Start Stop Clock Trigger IC Pin

-ve 12-11 +ve L2-11 -ve C2-39

** Tie K2-1 to ground **

Logic Probe — Signal On IC/Pin Name

R2-24 +5V R2-9 DDMAO R2-10 DDMAI R2-11 DDMA2 R2-13 DDMA3 R2-14 DDMA4 R2-15 DDMAS Test Pt.

Signature

826P A13F 37H3 9F59 69HU 9277 5530

Page 9

R2-16 R2-17

C. SA Settings for ROM2 Test (N/P2)

Probe Trigger

Start -ve

Stop +ve Clock -ve

** Tie K2-1 to ground **

D Signatures

Logic Probe

On IC/Pin

N/P2-9 N/P2-10 N/P2-11 N/P2-13 N/P2-14 N/P2-15 N/P2-16 N/P2-17 DDMA6 DDMA7

ICPin Test Pt.

L2-10 L2-10 C2-39 2

Signal Signature

Name

DDMAO

DDMAI 2AH5 DDMA3 F67C DDMA4 S5H7C DDMAS5 7FFH

DDMA2 3431

DDMA6 88U2 DDMA7 A433 725P. 2604

  • Vector Generator Data Buffer

A. SA Settings for VG Data Buffer test

ProbeTriggerICPin _ Test Pt.
Start-veL2-10
Stop+veL2-10
Clock—-veC2-392

B Signatures

Logic ProbeSignalSignature

On IC/Pin Name

P1-18 (19)DBO6334
1-17(18)DBI2AH5
P1-16(17)DB23431
P1-15 (16)DB3F67C
P1-14(15)DB4SH7C
1-13 (14)DBS7FFH
1-12(13)DB688U2
1-11(12)DB7A433
  • The numbers in brackets are the pin assignments when an AM8304B is used as opposed to a 74LS245 *