CATHODE RAY TOMES

Pit-Fighter CO-357-05 1st Printing Universal Kit Installation Instructions

Pit-Fighter (Tiger) (Tiger Electronics, 1991) · Installation · 13 pages · 26 sections · original scan

Page 1

Inter-Office Memo AM

ATARI

GAMES

To: Hide Nakajima (President)

Rich Moore (V.P., Engineering) John Ray (Engineering Team Director) Mark Pierce (Project Leader) (Programmer) Paul Kwinn (Programmer) . Glenn McNamara (Technician) Pat McCarthy (Eng. Supervisor) Sam Lee (Engineer) Jerry Momoda (Product Manager) Dave Cook (Product Designer) Stevie Landaverde (Harness Designer) Rick Meyette (Product Safety) Peter Takaichi (Design Services Director) Jed Margolin (Sr. Staff Electrical Engineer) Erik Durfey (Technical Associate) Lois Turner (Engineering Library)

From: Andrea Dencker, Publications Dept. duds Date: March 22, 1991

Subject: Internal Distribution of Pit-Fighter Universal Kit Installation Instructions, CO-357-05, 1st printing

Attached is your copy of the first printing of the Pit-Fighter Universal Kit Installation Instructions (CO-357-05).

If any people were inadvertently left off of this distribution list and you. think they should have copies of these publications, please let me know. For those of you who helped us on this project, we thank you very much!

Page 2

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 3

Installation

Copyright © 1990, 1991 by Atari Games Corporation. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher.

The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for substantial penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles.

In addition, the Act provides for payment of statutory damages of up to $50,000 per infringing transaction in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years as well as fines of up to $250,000 in the case of individuals and up to $500,000 in the case of corporations. Atari Games Corporation will aggressively enforce its copyrights against infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game. Published by: Atari Games Corporation 675 Sycamore Drive Milpitas, California 95036-1110 Printed in the U.S.A. 3/91 Produced by the Atari Games Technical Publications Department. Writing and Editing: Andrea Dencker Illustration and Design: Mary Ohanessian Sumner

Table of Contents Installation Introduction .. Cabinet Equipment Requirements Tools Required. Inspecting the Kit Preparing the Cabinet for the Kit Installation .. Assembling the Control Panel.. Connecting the JAMMA Harness.. Installing the Pit-Fighter Board Set. Installing the Bezel, Labels, Decals, and Attraction Assembly... Setting the Coin and Game Options... MYUWWNNH

© Pit-Fighter Universal Kit

Maximizing Earnings Game Pla:

° List of Mlustrations Figure 1 Installed Kit Parts .... Figure 2 Locations of Control Panel Holes to be Drilled... Figure 3 Template for One Player Station

° List of Tables Table 1 Equipment Requirements... Table 2 Contents of the Pit-Fighter Kit Table 3 JAMMA Pin and Wire Connections Table 4 Atari Games Video Connector Pin Assignments...

Note This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area or modification to this equipment is likely to cause interference, in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from an Atari game at your location, check the following:
  • All ground wires in the game are properly connected as shown in the game wiring diagram.
  • The power cord is properly plugged into a grounded three-wire outlet.
  • The game printed-circuit boards (PCBs) are properly installed with all screws in place and tightened. If you are still unable to solve the interference problem, please contact Customer Service at Atari Games Corporation. See the inside front cover of this manual for service in your area.

Safety Summary

Please refer to the complete safety summary printed on page iv in the Pit-Fighter Operator’s Manual. That manual was included with this kit.

Page 4

PIT-FIGHTER UNIVERSAL KIT

Installation

The Pit-Fighter™ two-player conversion kit includes this supplement and the Pit-Fighter Operator’s Manual (TM-357). > This supplement provides information for installing, testing, and troubleshooting the parts in the conversion kit.

The Operator’s Manual contains a description of the game play and the selftest, troubleshooting

and maintenance pro-

cedures for the joystick control, plus applicable parts lists, illustra-

tions, and schematics. Also printed in the back of that manual is the statistics sheet.

Page 5

Installation

WARNING To avoid electrical shock, unplug the cabinet while installing the kit. After installation, plug the game only into a grounded 3-wire outlet.

Cabinet Equipment Requirements Table 1 lists the equipment required in the cabinet into which you are installing the Pit-Fighter kit.

CAUTION Do not unplug or plug in the Pit-Fighter game printed-circuit board (PCB) edge connector while the power is on. You could seriously damage the PCB.

Tools Required © Drill with a 1/4-inch and 5/16-inch drill bits © Phillips screwdriver ¢ Flat-blade screwdriver

  • Socket wrench set and ratchet
  • 1/4-20 hex wrench ¢ Wire cutters and strippers Pit-Fighter Universal Kit

Table 1 Equipment Requirements

Equipment Specification Video Display Color RGB monitor Separate positive horizontal and vertical sync or negative composite sync Horizontal mounting Horizontal frequency: 15.750 KHz Vertical frequency: 60 Hz Video input: 1V to 3V peak-to-peak positive polarity Control Panel Metal only Speaker 8, 10W Coin Counter +5 VDC or +12 VDC Power Cord Three-conductor with ground Power Supply +5 VDC + 0.25V @ 3.0 amps +12 VDC @ 1.0 amp -5 VDC @ 1.0 amp (optional)

  • Straight edge © Squeegee ¢ X-ACTO™ knife
  • Insulated wire connectors (if you are installing a new JAMMA harness) © Carbon paper ° Saber saw ° File

Table 2 Contents of the Pit-Fighter Kit

Part No.DescriptionQty.Part No.DescriptionQty.
A047955-05Pit-Fighter Kit PCB Assy. (2-Player038158-01Product ILD. Label1
Version)1039450-01FCC Compliance Labeli
A046501-01JAMMA Harness Assy.1TM-357Pit-Fighter Operator's Manual1
048421-01Control Panel Decal1CO-357-05Pit-Fighter Universal Kit Installation
048422-01Side Panel Decals2Instructions (with control panel

template) 1

048423-02Attraction Panel Film1
048425-02Monitor Bezel with Graphics1141026-001.50"-Inside Diameter Ferrite Split Beads Z
178237-005Blue Button Assemblies=}178032-002#10-24 Wire & Cable Tie
178237-001Red Button Assemblies375-5112B#10-24 x 3/4"-Long Black Carriage Bolts 2

175014-1040 #10 Flat Washers

171097-0018-Position Black Wico Joystick Assy.2
178283-005Start/Jump Indicator Plates2178265-001L-Style Nylon Standoffs4
178283-006Punch Indicator Plates272-6608S#6 x 1/2"-Long, Type AB, Pan-Head,
178283-007Kick Indicator Plates=2Cross-Recessed Screws4

Packaging materials are not listed. Note: An attraction

160044-001Snap-Action Switches6shield and control panel cover are not included in this kit.
177026-0040#10-24 Nut/Washer Assemblies12
Page 6

Pit-Fighter Universal Kit Installation

Figure 1 Installed Kit Parts

; =i. . Preparing the Cabinet for the

—_ - Kit Installation Inspecting the Kit

WARNING Check to see that you have all the parts listed in the kit parts list in Table 2. If any part is missing or damaged, contact your distributor with the Pit-Fighter kit serial number, part number, and description of the missing or dam- To avoid electrical shock, unplug the cabinet while installing the kit. After installation, plug the game only into a grounded 3-wire outlet. aged parts, and date received.
Page 7

Installation Pit-Fighter Universal Kit

Table 3 JAMMA Pin and Wire Connections

Instructions

LT PUNCH BTN Connect this wire to the N.O. terminal of the left Punch switch. Connect the common termi- Wire

PinColorSignal

Component Side

1BNGND
2BNGND
3R+5V
4R+5V
5OR-5V
6ay+12V.

7 Key

8BU/WCOIN CTR1

9 Not used

10BNSPKR +

11 Not used

12RRED
13BUBLUE
14BK‘VIDEO GND
15WwSELF-TEST
16YLT COIN
17W/BKNot used
18W/BNLT JOYST UP
19WRLT JOYST DN
20W/ORLT JOYST LT
21WhyLT JOYST RT

22 ‘W/GN

23W/BULT KICK BTN
24WINLTJUNP BIN
25W/GYNot used
206=«=~NVNot used
27BK/WGND
28BK/WGND

Connect to the 5V RTN (GND) terminal on the power supply. However, if you have 12V RTN, connect one of the BN wires at pin 1, 2, A, or B to the 12V RTN terminal. Same as pin 1. Connect to the +5V terminal on the power supply. However, if your power supply has a +SENSE terminal, connect one of the R wires at pin 3, 4, or C to +SENSE instead of +5V. Same as pin 3. Connect to the —5V terminal of the power supply. If -5V is not available, connect to the 12V RTN or the 5V RTN (GND) or leave it unconnected. ba Ifyou do not bave (or use) -5V, the maximum power to the speaker will be reduced by balf. Connect to the +12V terminal of the power supply. If your coin counter(s) require 12V, also connect to the + side of the coin counter(s).

Connect this wire to the — side of the coin counter. Note: Do not use 24V counters. Connect the + side to +5V or +12V on the power supply, as appropriate.

Connect to the + terminal on the speaker. (This wire is part of a twisted pair.)

Attach to the video display. Attach to the video display. Attach to the video display. Use this wire if you want an external self-test switch. However, the kit already has a self-test switch on the PCB, (If you connect an external self-test switch, switch off the switch on the PCB. Connect the wire to the N.O. terminal on the external self-test switch. Connect the common terminal of the switch to a BK/W wire [GND].) Connect to the N.O. terminal of the left coin switch. Connect the common terminal of the switch to a BK/W wire.

‘Connect to the N.O. terminal of the switch. Connect the common terminal of the switch to ‘one of the BK/W wires. Same as pin 18. Same as pin 18. Same as pin 18.

nals of the switches to one of the BK/W wires. Connect this wire to the N.O. terminal of the left Kick switch. Connect the common terminals of the switches to one of the BK/W wires. Connect this wire to the N.O. terminal of the left Jump switch. Connect the common terminals of the switches to one of the BK/W wires.

Connect one of the BK/W wires at pin 27, 28, e, and f to the negative sense terminal of the power supply (if it exists) and one to the common terminals of the coin switches. Connect two of these wires to the common terminals of the control switches on the control panel. Same as pin 27._

Page 8

Pit-Fighter Universal Kit Installation

Table 3 JAMMA Wire Connections, Continued

Wire

Pin Color Signal Instructions

Solder Side

ABNGNDConnect to the 5V RTN (GND) terminal on the power supply.;, if you have 12V

RIN, connect one of the BN wires at pin 1, 2, A, or B to the 12V RTN terminal.

BBNGNDSame as pin A.
cR+5V.Connect to the +5V terminal on the power supply. However, if your power supply has a

+SENSE terminal, connect one of the R wires at pin 3, 4, or C to +SENSE instead of +5V.

DR+5VConnect to the +5V terminal on the power supply. However, if your power supply has a

+SENSE terminal, connect one of the R wires at pin 3, 4, or C to +SENSE instead of +5V.

EOR—5VConnect to the -5V terminal of the power supply. If -SV is not available, connect to the 12V

RTN or the 5V RTN (GND) or leave it unconnected.

NOTE: If you do not have (or use) —5V, the maximum power to the speaker will be reduced by half.
F¥+12VConnect to the +12V terminal of the power supply.

H Key

Jv/WCOIN CTR2Connect this wire to one side of the second 12V coin counter. Clip R13 on the game PCB if

K Not used

LWwSPKR-

M Not used

NGNGREEN

P BN COMPSYNC

RGYService

s Not used

TORRT COIN
UY/BK—Not used
b &Y/BNRT JOYST UP
WwY/RRT JOYST DN
xY/ORRT JOYST LT
‘¥:Y/wRT JOYST RT

Zz

aY/BURT KICK BTN
bY/VRT JUMP BIN
cY/GYNot used
dGY/WNot used
eBK/WGND

you use a second coin counter. Note: Do not use 24V counters. If your counter requires 5V, connect a wire from the +5V terminal on the power supply.

Connect to the — terminal on the speaker. (This wire is one of a twisted pair.)

Attach to the video display. Attach to the video display.

Connect to the N.O. terminal of the right coin switch. Connect the common terminal of the switch to a BK/W wire.

Connect to the N.O. terminal of the switch. Connect the common terminal of the switch to one of the BK/W wires. Same as pin V. Same as pin V. Same as pin V. Y/GN RT PUNCH BTN Connect this wire to the N.O. terminal of the right Punch switch. Connect the common terminals of the switches to one of the BK/W wires. Connect this wire to the N.O. terminal of the right Kick switch. Connect the common terminals of the switches to one of the BK/W wires. Connect this wire to the N.O. terminal of the right Jump switch. Connect the common terminals of the switches to one of the BK/W wires.

Connect one of the BK/W wires at pin 27, 28, e, or f to the negative sense terminal of the power supply (if it exists) and one to the common terminals of the coin switches. Connect two of these wires to the common terminals of the control switches on the control panel. Same as pin e.

Page 9

Installation:

Figure 1 shows almost all kit parts installed in a typical cabinet. Use this illustration as a guide while you install the parts.

  • Turn off power to the game, and unplug the power cord.
  • Remove the following from the cabinet: ° Existing PCBs ¢ Game harness, if it is not Japan Amusement Machinery Manufacturers Association (JAMMA)compatible © Control panel decals, labels, and controls © Side decals, graphics, and adhesive. If the cabinet sides are damaged, repair them before putting on the new decals.
  • Video display (monitor) shield, display bezel, attraction shield, and marquee, if any.
  • Wipe down and vacuum the cabinet. Paint the cabinet, if required.

Assembling the Control Panel

Parts Needed To assemble the control panel, you need the control panel hole-cutting template, which is printed at the end of this supplement. Cut out the template sheet. You will need to obtain a clear acrylic cover for the control panel: it must be 3/16" thick and larger than the di- Pit-Fighter Universal Kit

mensions of your game’s control panel. Gather together the following parts from the kit:

  • Control panel decal
  • Three red and three blue button assemblies

© Six snap-action switches © Two each of the Start/Jump, Punch, and Kick indicator plates © Two joystick controls © Twelve #10 x 3/4"-long black carriage bolts, flat washers, and nut/washer assemblies

Installing the Parts

  • Using carbon paper, transfer the joystick mounting pattern from the template to the control panel. Save the template, since you will need it for the second player station. Also refer to Figure 2 for the exact locations of all holes.
  • Drill four 1/4" holes in the metal control panel for each joystick’s mounting bolts.
  • Using a saber saw, carefully cut out the large holes for the joysticks. Deburr the sharp edges with a file.
  • Lay the acrylic cover over the top of the control panel and mark the outside shape of the panel on the plastic. ‘Also mark the six button holes as close as possible to the locations shown on the template. Lastly, mark the positions of the four holes that will be used for securing the cover to the control panel. These four holes

Py a

NOTE The four holes in

50 the corners are

not shown in this illustration. Drill these holes wher- 2 ever space perfront of the control panel. ne Check that the joysticks have sufficient clearance before cutting holes. CL

Figure 2 Locations of Control Panel Holes to be Drilled

Page 10

Pit-Fighter Universal Kit

can be placed anywhere near the corners — wherever space permits.

  • Using a bandsaw, cut the control panel cover to its correct outside shape.
WARNING Wear safety glasses when drilling the plastic control panel cover. Use care to avoid shattering or chipping the plastic.
  • Tape or glue the template to the acrylic cover. To start the saber saw cut, drill a 1/2" hole inside the large and smaller holes.
  • Saw out the large and smaller holes.
  • Drill the four 5/16" holes that will be used to mount the cover to the control panel and the eight 1/4" holes to mount the joysticks.
  • To prevent injury, carefully deburr all the edges of the acrylic cover.
  • Install the control panel decal on the control panel. Use a sharp X-ACTO knife to trim the outside edge and to cut out the holes for the controls.
  • Install the cover on the control panel with the four 3/4"-long carriage bolts, flat washers, and nut/washer assemblies.
  • Install the joystick assemblies using the eight 3/4"-long carriage bolts. Install the six button assemblies and the six indicator plates as shown in Figure 1.
NOTE The orientation of the joysticks is critical. Refer to the template for a picture of the correct position.

For maintenance and servicing information on the joystick controls, refer to Chapter 3 of this manual.

Connecting the JAMMA

Harness

  • If your game cabinet does not already have a JAMMA harness, install the JAMMA harness in the cabinet.
  • Install the split beads on the harness as close to the PCB edge connector as possible. Hold the*beads on the harness with the tie wrap included in the kit. Installation
CAUTION You must install the split beads included in the kit on the JAMMA harness to meet FCC requirements.
  • Using Table 2 for wiring information, connect the JAMMA harness to existing component harnesses. Use crimp splices or butt soldering.
WARNING Do not simply tie the wires together. If you do, you could cause intermittent problems, loose connections, oxidation, or a fire.

Connecting Power Wires

  • Connect the wires on the JAMMA harness to the wires for the power supply, as shown in Table 3. The Pit- Fighter kit requires +5V and +12V. If -5V is available, it should be used too. Tie off any other voltage wires on the power supply besides +5V, -5V, and +12V. There is more than one wire for each voltage in the JAMMA harness. Use more than one wire for each voltage (connecting them as described in Table 3) so that the edge connector does not overload and burn.

Connecting Video Display Wires

NOTE The JAMMA harness provides only negative composite sync. If your video display requires separate positive sync, this kit has a standard Atari Games video connector (located near the JAMMA connector) that provides separate positive sync. Refer to Table 4 and make the appropriate connections for your video display.

Connect the wires designated for the red, green and blue video guns along with the sync and ground wires, according to Table 3.

Table 4 Atari Games Video Connector Pin Assignments

PinSignalPinSignal
1RedeAGND
2GND8GND
Ee}Key>Negative composite
4Greensyne
biGND10Positive V sync
6Blue11Positive H sync
Page 11

Connecting Coin Door Wires

  • Connect the wires on the JAMMA harness to the coin switches and meter according to Table 3.
  • Connect one terminal of the door lamps to one of the BK/W wires. Connect the other terminal of the door lamps to the R wire supplying +5V.
NOTE Do not use -5V for the coin door lamps. -5V is required for audio.

Some games have separate power supply outputs for the coin door lamps. If you choose to use these outputs, make sure you connect both terminals of each lamp to the terminals on the power supply.

Connecting the Control Wires Connect the JAMMA harness to the joystick and button switches, following the information in Table 3.

Grounding the Cabinet Find the ground lead (green) of the 115V input power line. Connect this lead in daisy-chain fashion to a bare metal part of the coin door, the control panel, the video display, and the power supply. This AC ground must be of #18 AWG wire or larger.

WARNING For the safety of players, you must connect the green ground wire as indicated above.

Checking the JAMMA Connections Before plugging in the game PCB, turn on the power to the game, and check +5 Volts on pins 3, 4, C, and D of the JAMMA connector; +12 Volts on pins F and 6; and —5 Volts on pins E and 5. Check that the video display and the attraction lamp have power. Now turn off the power to the game.

Installing the Pit-Fighter

Board Set

  • After you have checked the power on the JAMMA connector (above), install the Pit-Fighter game beard set in the cabinet. Use the nylon standoffs and four #6 screws in the kit.
  • Connect the JAMMA connector to the PCB.
  • Secure the JAMMA harness away from the PCB with cable ties. Pit-Fighter Universal Kit

4, Tum on the power to the game. Check that the game PCB functions. If a video picture is not present, see Chapter 3.

Installing the Bezel, Labels, Decals, and Attraction Assembly

These kit parts are shown assembled in a game in Figure 1.

Installing the Display Bezel Find the cardboard display bezel in the kit. This bezel can only accommodate a 25-inch video display. For 19-inch displays, cut out the Pit-Fighter instructions area from the bezel in this kit, and adhere it to a black 19-inch bezel.

Installing the Product ID and FCC Label

Place the product ID label and FCC compliance label on the back of the cabinet.

Installing the Side Panel Decals Find the side panel decals in the kit, Wet the left and right side panels of the cabinet with slightly soapy water. Then position the decals as shown in Figure 1. Remove any wrinkles in the artwork using a squeegee. Allow the sides to dry. Installing the Attraction Assembly Find the Pit-Fighter attraction film in the kit. Clean the existing attraction shield that was in your cabinet. If that shield is damaged or scratched, obtain a new piece of acrylic that is 1/8" thick. Using this shield as a template, cut the film to size, if necessary. Install them on the cabinet as shown in Figure 1.

Setting the Coin and Game Options

Set the coin and game options in the self-test. See Chapter 2 of the Pit-Fighter Operator’s Manual for information about the option settings.

Maximizing Earnings

For maximum earnings, regularly maintain your Pit-Fighter game. If you have problems, follow the instructions in Chapter 3 of the Pit-Fighter Operator’s Manual. When you set up the game and when you collect money, perform the automated self-test and check the controls with the Switch Test and Sound Test in the self-test.

Game Play Refer to the Pit-Fighter Operator’s Manual for a complete description of the Pit-Fighter game play.

Page 12

Figure 3 Template for One Player Station ?

Top edge of control panel

(closest to monitor)

‘Start/Jump

Button

Joystick -

Punch Button Kick Button

NOTE

The three blue buttons should

be installed at the left player ‘station, and the three red but-

tons at the right. Pit-Fighter Universal Kit Installation

Page 13

AN

ATARI

GAMES

Atari Games Corporation

675 Sycamore Drive

Milpitas, California 95036-1110