CATHODE RAY TOMES

Golden Tee 3D Golf

Golden Tee 3D Golf (v1.93N) (Incredible Technologies, 1995) · Manual · 32 pages · 78 sections · original scan

Page 1

INSTALLATION MANUAL

LN CREDIBLE

Page 2

INCREDIBLE TECHNOLOGIES, INC.

SERVICE / SALES (800) 262-0323 FAX (708) 870-0120

Hardware and Software ©Copyright 1995 Incredible Technologies, Inc. All rights reserved.

WARRANTY, REPAIR and RETURN POLICY

© 90-day warranty on all electronic components. All warranty periods begin on the date of purchase from Incredible Technologies, Inc..

e There is a minimum $40.00 service charge for all non-warranty repairs or returns.

e For all servicing return to Incredible Technologies, Inc.

e ANY non-factory repair or attempted repair voids warranty.

e AAMA decal must not be removed from the PCB. Warranty voided if removed.

RETURN MERCHANDISE AUTHORIZATION

e All returned merchandise must have a Return Merchandise Authorization (RMA) number marked clearly on the outside of the package.

¢ You must obtain all RMA numbers from your authorized Incredible Technologies, Inc. distributor. Please have your Incredible Technologies, Inc. serial number available when calling for an RMA number.

© Merchandise returned without an RMA number will not be accepted.

e Advance replacement boards will be shipped to distributors or, at the distributor’s request, will be shipped directly to the operator.

e Advance replacement boards will be billed to the distributor until Incredible Technologies, Inc. receives the returned board, at which time a credit will be issued.

¢ All repairs and/or replacements will be shipped within 24 hours of receipt or request (subject to availability).

FCC REGULATION COMPLIANCE

This equipment complies with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules, These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Page 3

Table of CONTENTS

  • GETTING STARTED.............. cece 2 GAME PACKAGE CONTENTS ........cccscssssesreseenenee 2

RECOMMENDED TOOLS AND SUPPLIES. ...........-. iN) [2] INSTALLATION PREPARATION THE CABINET. Power Requirements: Monitor Requirements: Cabinet Selection:... Preparing a used cabinet for Golden Tee 3D Golf: THE CONTROL PANEL Trackball Preparatior Button Preparation: THE GRAPHICS OVERLAY . Control Panel Overlay Installation: Function Labels Overlay Installatio! Marquee Installation:.. WIRING AND HARDWARE ASSEMBLY Control Panel Assembly: Printed Circuit Board (PCB BOOONNNN NOOO DAW WHWNMN VY

Coin Doors, Test Switch, Service Button, and Volume Control Wiring: MARS LIGHT HOOKUP. Final Check:.. [3] INITIAL START-UP . [4] DIP SWITCH SETTINGG...................10 oon VOLUME SETTINGS 1.0... cecececeseseeseseseeteesteeeneeenenes 11 OPERATOR ADJUSTABLES . Game Mode Selectior

Attract Mode Sounds: Credits and Coin Doo: Delay Time Adjustment: Skill Level Adjustment: Hole In One Contest Mod

GAME AUDITS Display Coin Audits: Display Game Selection Audit: Number of Golfers and Holes Oak Valley Audits: Ocean Pointe Audit Cactus Canyon Audit: Reset Audits :

SYSTEM TESTS et

Full GROM Checksum Test: Fast GROM Checksum Test Video Ram Test: Palette RAM Test Board Tests : Sound Tests: Control Panel Te:

APPENDIX A GENERAL TROUBLESHOOTING............... 20

VIDEO PROBLEMS ........cccssssssssesssssssssssssseeeeeees a1

SOUND PROBLEMG.......cccssssssssesssssssssssssseeeeeenes 22

CONTROL PROBLEMS...

POWER-UP PROBLEMS.

MISCELLANEOUS PROBLEMS

APPENDIX B JAMMA HARNESS CONNECTION............. 26

Page 4

GETTING STARTED

GAME PACKAGE CONTENTS

  • Printed Circuit Board (PCB) Assembly
  • Connecting Wire Harness (JAMMA)
  • Trackball Assembly w/Metal Plate
  • Trackball Cable Assembly
  • Button Assemblies
  • Marquee Styrene
  • Marquee Plexiglas
  • Control Panel Overlay
  • Set of Function Labels
  • Manual

RECOMMENDED TOOLS

AND SUPPLIES

Phillips and Slotted Screwdrivers Socket Set Wire Cutters and Strippers Pliers or Channel Locks Electric Drill with 3/32”, 4”, and 7/16” Bits 1-3/16” Chassis or Sheet Metal Punch Small File Razor Knife and Sharp Blades Straight Edge Staple Gun and Staples Soldering Iron and 60/40 Resin Core Solder Vacuum Cleaner Assorted Fastening Hardware Heat Shrink Tubing (3/32”, 1/8”, and 3/16”) Masking Tape 3-1/2” or 4” Wire Ties

IF YOU DO YOUR OWN PAINTING, ‘YOU'LL NEED THESE PAINT SUPPLIES: e Air Brush or Paint Sprayer Paint Roller and Pan Paint Brush Paint (and Primer) Sandpaper Putty Knife and Wood Putty

2- GOLDEN TEE 3D GOLF

INSTALLATION PREPARATION

BEFORE YOU START.....

  • Check to see if all the needed parts have been included in your kit (See GAME PACKAGE CONTENTS .)
  • Do you have the necessary tools? (See RECOMMENDED TOOLS AND SUPPLIES.)
  • Do not work with any part of the system plugged in (lights, monitor, or power supply).

THE CABINET

POWER REQUIREMENTS:

Make sure the game you have chosen to convert is able to supply all the required voltages for GOLDEN TEE 3-D GOLF.

NOTE: The output level of many “regulated” switching power supplies actually vary with load. For this reason, the power supply from an old game may not be correctly adjusted for GOLDEN TEE 3-D GOLF. This makes the existing power supply inappropriate and hazardous to your new game. Therefore, it is very important to adjust the +5 VDC supply WITHOUT connecting the PCB, then readjusting it later, after the PCB has been installed. Measure power on the PCB, across an I.C. Damage will occur if the power supply is outside the acceptable limits (between 4.8 and 5.5 VDC.)
Page 5

MONITOR REQUIREMENTS:

GOLDEN TEE 3-D GOLF requires a monitor in a horizontal mount raster scan with negative composite SYNC. It can be difficult to change the monitor from vertical to a horizontal unit, therefore, installation will be easier if you choose a horizontal mount cabinet.

NOTE: For 33” monitors, a 75 ohm pull-up resistor may be required on the sync line of the video board. The appropriate place to put resistor is across diode D9. The need for the 75 ohm pullup resistor is if you are unable to get a syncronized picture by adjusting the monitor.

CABINET SELECTION:

You can choose either a new cabinet or a used cabinet for your GOLDEN TEE 3-D GOLF game. Reusing a cabinet is by far the most cost-effective way to maximize the return of your initial investment. In either case, all you need to provide is the cabinet with a power supply and monitor. We provide the rest. The end result is a new game at a very low cost.

NOTE: {t is recommended that a large control panel with a 25” monitor, like those on a 4-player cabinet, be used for your GOLDEN TEE 3D GOLF.

When selecting a cabinet, keep this in mind: A cabinet with a 25” monitor and a large control panel will allow you to mount the trackball farther from the monitor. This prevents players hands from hitting the monitor glass when rolling the trackball forward, and will earn better than a smaller control panel with a smaller monitor.

PREPARING A USED CABINET FOR

GOLDEN TEE 3D GOLF:

  • Remove the following from the cabinet:

Main Logic Board(s) Control Panel Monitor Plexiglas Marquee Cabinet Graphics

  • Thoroughly clean out your cabinet. Remove all the old buttons, joysticks and wires from the control panel. DO NOT remove monitor and speaker wires.
  • Remove the old graphics and adhesive from the control panel, and the side of the cabinet. Remove adhesive with solvent.
  • For a fresh look, painting is highly recommended. Spray painting gives a better finish, but if an air brush or paint sprayer is unavailable, a roller is second best. Remember to cover all exposed surfaces not to be painted.
  • Remember, spending time on the cabinet’s appearance (i.e., marquee, control panel, and cabinet graphics) will raise your profits with the introduction of a new game package, especially if the cabinet looks clean and new.
  • The “new game look” should always apply to the inside of your game as well. A few wire ties and shrink tubing on your harness, some fastening hardware on your subassemblies, and a sweep with the vacuum cleaner will ensure that glitches do not occur.

THE CONTROL PAN

Mounting the trackball correctly and securely is very

important for the profitability of your new game. Follow these instructions carefully for mounting the trackball to: 1) a metal control panel; 2) a wooden contro! with routing; 3) or a wooden control panel without routing. (Refer to template inserts found in the back of the manual.)
NOTE: Installing the trackball as far away from the monitor as possible will prevent players hands from hitting the monitor glass when rolling the trackball forward.

TRACKBALL

CONTROL PANEL LAYOUT (NOTE: TRACKBALL SHOULD 8E CENTERED ON THE CONTROL PANEL)

GOLDEN TEE 3D GOLF - 3

Page 6

TRACKBALL PREPARATION:

When making the hole for the trackball, follow the instructions, starting on the right, for the type of control panel you will be using.

NOTE: When installing the trackball, make sure the trackball is in the correct orientation. (Refer to picture below.)

Trackball Orientation Diagram

MONITOR

a. Mota Mounting Pate ©3118" Moueting Hotes, oe . | Ta ° Teacatauantly | |

Lf / N J wna ©

PLAYER 8 IMPORTANT: oso ne rasibal af 31 ay tom the onto! as cossle fe suse tre ractbaiss mounted sragre gai te covest onertayon

TRACKBALL ORIENTATION (NOT DRAWN TO SCALE) To mount trackball to a metal control panel use TRACKBALL MOUNTING TEMPLATE #1

Fill any existing holes in the metal control panel.

Place and secure TEMPLATE #1 to your control panel in the desired location.

NOTE: The trackball should be as far away from the monitor as possible.

Carefully drill the holes for the ball and the mounting bolts using the template as a guide.

Remove template and file down any rough edges.

See THE GRAPHICS OVERLAY section on page 5 on how to install the graphics.

Mount trackball under the metal control panel using the four carriage bolts.

NOTE: Be sure the trackball is mounted as shown in the diagram on page 3.
NOTE: Do not over-tighten the trackball. It will warp and cause the trackball to not operate correctly.
NOTE: The supplied metal plate is not needed with metal control panels.
NOTE: Be sure to mount the trackball so as much of the ball is exposed as possible.

If using Plexiglas on your control panel, it is highly recommended that a 3-1/2” hole be cut in the Plexiglas for the trackball. This allows for players to use the full height of the trackball. Carefully file and smooth the edges of the hole in the Plexiglas so players do not cut their hands when playing.

4- GOLDEN TEE 3D GOLF

Page 7

To mount trackball to a wooden control panel with routing capability use TRACKBALL MOUNTING TEMPLATE #2

Fill any existing holes in the wooden control panel.

Place and secure TEMPLATE #2 to your control panel in the desired location.

NOTE: The trackball should be as far away from the monitor as possible.

Carefully cut the hole for the trackball in the shape indicated on the template.

Drill the mounting holes indicated.

Next route out the shaded area indicated on TEMPLATE #2, 1/16” deep. Use a 1/2” Rabbiting Bit for best results. This is so the supplied metal plate will be flush with the control panel surface.

Remove template and file down any rough edges.

See THE GRAPHICS OVERLAY section on page 5 on how to install the graphics.

Mount trackball to the metal plate using the four carriage bolts supplied. Then mount the metal plate to the wooden control panel.

NOTE: Be sure the trackball is mounted as shown in the diagram on page 3.
NOTE: Do not over-tighten the trackball. It will warp and cause the trackball to not operate correctly.
NOTE: Be sure to mount the trackball so as much of the ball is exposed as possible.

If using Plexiglas on your control panel, it is highly recommended that a 3-1/2” hole be cut in the Plexiglas for the trackball. This allows for players to use the full height of the trackball. Carefully file and smooth the edges of the hole in the Plexiglas so players do not cut their hands when playing. To mount trackball to a wooden control panel without routing capability use TRACKBALL MOUNTING TEMPLATE #3

Fill any existing holes in the wooden control panel.

Place and secure TEMPLATE #3 to your control panel in the desired location.

NOTE: The trackball should be as far away from the monitor as possible.

Carefully cut the hole for the trackball in the shape indicated on the template. The trackball should fit the hole shape exactly.

Drill the mounting holes as indicated.

Remove template and file down any rough edges.

Using the TRACKBALL ORIENTATION TEMPLATE, cut a 3” hole in the Plexiglas overlay to fit over the trackball. Be sure to include holes for the buttons, and all of the mounting bolts.

See THE GRAPHICS OVERLAY section on page 5 on how to install the graphics.

Insert the trackball into the newly cut hole. Place Plexiglas overlay on top of the control. panel. Place the supplied metal plate under the trackball and use the carriage bolts to secure it to the control panel. The metal plate below and the Plexiglas above will secure the trackball assembly into position.

NOTE: Be sure the trackball is mounted as shown in the diagram on page 3.
NOTE: Do not over-tighten the trackball. It will warp and cause the trackball to not operate correctly.
NOTE: Be sure to mount the trackball so as much of the ball is exposed as possible.

GOLDEN TEE 3D GOLF - 5

Page 8

BUTTON PREPARATION:

  • When making the holes for the buttons, DO NOT use the Function Labels to outline any new holes. The Function Labels are designed to fit right over the buttons when installed on the control panel. If the labels are used as a template the holes will be too big, and the buttons will fall through. Instead, use the labels as a guide to where you want to drill your new holes, and then cut a 1- 1/8” hole in the center of where the labels are to be placed. DO NOT stick the labels to the panel at this time.
  • Drill or punch the holes marked for buttons or bolts. Use a chassis or sheet metal punch for best results on button holes.
  • Use a file to smooth any rough edges on the holes.
  • Fill any old and unused holes with wood, resin, or a metal plate.
  • It is recommended that you cover your control panel with Plexiglas. Now would be a good time to cut it to fit while the dimensions and tools are at hand.

THE GRAPHICS OVERLAY

GOLDEN TEE 3-D GOLF comes equipped with graphics that will accommodate a variety of existing game cabinets.

CONTROL PANEL OVERLAY INSTALLATION:

FUNCTION LABELS OVERLAY INSTALLATION:

  • Remove the protective backing from the background overlay. Center the background overlay over the control panel and place down gently, making sure to keep it square. Using your hands, press down firmly, starting from the center and smooth the background overlay outward, making sure all bubbles have been pressed out for a clean, flat surface.
  • Using a sharp razor knife, trim any excess from the background overlay. Carefully pierce through the overlay above each control panel hole that you have marked. Cut out material covering the pre-drilled holes with the razor knife. Be sure to cut the background overlay above each hole and trim cleanly and evenly.
  • Make sure the contro! panel is clean and free from dust, grease, metal filings, and sawdust. The background overlay provided with the game is oversized to accommodate most control panel sizes. Center the background overlay on the control panel surface. Be sure to leave enough excess material above and below the control panel in order to trim it evenly. Line up the supplied function labels with the corresponding control panel holes. Remove the backing and carefully press into place. Be sure they are straight. Attach the HOOK/SWING reference diagram above the trackball label. If your control panel is too narrow to fit the reference diagram, mount the diagram under the monitor glass on the bezel. Refer to the diagrams below.

HOOK / SWING Reference Overlay misTRUCTION TRACKBALL OVERLAY

FUNCTION LABEL LAYOUT #1 (NOTE: TRACKBALL SHOULD BE CENTERED ON THE CONTROL PANEL) (eo)

or put the HOOK/SWING Reference diagram on the bezel

MONITOR

FUNCTION LABEL LAYOUT #2

6 - GOLDEN TEE 3D GOLF

Page 9

MARQUEE INSTALLATION:

PRINTED CIRCUIT BOARD (PCB):

If your cabinet needs a new marquee glass, determine the correct size and cut the Plexiglas (supplied) to fit. Using the old marquee glass as a template, center the Plexiglas on your new marquee graphics, making sure that all the printed images will be visible. Using a razor knife, score the new marquee deeply, following the edges of the old glass. Carefully break off the styrene. Be sure the light behind the marquee works and that the glass is clean on both sides. Now install the marquee graphics and glass securely.

WIRING AND HARDWARE

ASSEMBLY

REMEMBER! DO NOT WORK WITH ANY PART OF THIS SYSTEM PLUGGED IN (Lights, Monitor, or Power Supply).

NOTE: All switch wires used in this game need to be wired to the normally open connection on the switches. Each switch requires a ground wire on the common connector and the appropriate control or switch wire on the other normally open connector of the switch.

CONTROL PANEL ASSEMBLY:

Mount the PCB to the side of the cabinet with the connector toward the top of the drawer. This will keep the wire harness from slipping off due to vibration. Mark and drill pilot holes (3/32”) onto the cabinet side, being careful not to drill through to the outside. Attach the PCB standoffs to the cabinet using wood screws and spacers, snug but not too tight or the board may warp or crack. Be sure the board is not being flexed in any way.

WIRE HARNESS:

  • Install the trackball and buttons on the control panel by following the detailed instructions beginning on page 3. The two red buttons are used for FACE LEFT and FACE RIGHT. The white button is used as the START button. PLEASE NOTE: If you want your new game to earn money, you must install the trackball correctly.
  • If you are using Plexiglas for added protection, don’t forget to place it on the panel before inserting the buttons.
  • Wire the trackball and buttons using the JAMMA Harness Connection table on page
  • Connect the trackball using the supplied trackball cable into PLAYER 1 on the Memory Board.
  • If you are __ installing GOLDEN TEE 3-D GOLF into a Dynamo cabinet with a pre-installed JAMMA harness, you will notice that it does not have a wire for the test switch. You will have to add a contact to the edge connector at the proper position (position 15). Some cabinets (Dynamo included) have only one coin switch input and the coin switches are wired together. Connect the designated wires to the coin switches separately.
  • Attach the wire harness connector to the PCB. Be sure it is mounted correctly.
WARNING! - Make sure you have identified PIN 1 on the connector before powering up. Plugging the JAMMA connector in backwards will cause damage to the PCB.
  • It is best to use connectors (not supplied) whenever joining a set of harness wires to a subassembly. If you choose to solder wires together, follow this procedure:

¢ Strip off about %” of insulation from the wire.

e Slide a piece of heat-shrink tubing over the end.

  • Donot leave a lot of excess wire spooled up in your cabinet. Cut the wires to the length you need plus a few extra inches. Leave enough for proper cable dressing. Do not make it stretch across the inside of the cabinet.
  • Solder the new wire to the original wire. Use a straight in-line splice.

GOLDEN TEE 3D GOLF - 7

Page 10

POWER WIRES:

  • Connect the wires that are designated for your power supply. You will need a supply of +5 vdc, and +12 vde. The +5 vdc must be regulated to within 5% (+ or - 0.25. The +12 vdc may be unregulated but should not stray too far or the sound may be affected. If the cabinet’s supply does not provide these voltages, it will have to be replaced. A_ switching-type supply is recommended.
  • You will notice that you have more than one wire for each voltage. Use all wires supplied on the harness. This will ensure better power transmission and prevent overloading of the edge connector pads.
  • Tin all power supply wires before connecting them to the power supply. Loose strands may short out the supply. For best results, connect spade lugs to the ends of the power wires and attach to the screw terminals of the power supply.

MONITOR WIRES:

Position speakers as far from the monitor as Possible. If placed too close, the speaker's magnet may deflect the monitor and cause strange coloration, which can usually be corrected by degaussing the monitor. Make sure everything else in the cabinet is attached securely for the same reason.

SYNC:

This is the recommended approach for a Wells- Gardener monitor and should work with some others as well.

If your monitor does not have a composite SYNC input but has separate horizontal and vertical SYNC inputs, try connecting the composite SYNC signal from the PCB to the negative horizontal SYNC signal on the monitor. This should produce a satisfactory result, although some adjustment of the monitor's SYNC controls may be necessary.

Coin Doors, TEST SwiTcH, SERVICE BUTTON, AND VOLUME CONTROL WIRING:

You will be connecting the RED, GREEN, and BLUE video drives along with the composite SYNC and video GROUND wires.

SPEAKER WIRES:

Connect the speaker wires paying attention to their polarity.

NOTE: If your cabinet has two speakers, connect both. If they are 8 or 16 ohm ‘speakers, connect them in parallel, if they are 4 ohm, connect them in series.
NOTE: Examine the speaker carefully. Is it really up to the high standards you wish to maintain at your location? Unfortunately, many arcade speakers are inadequate for reproduction of good game sounds. Remember, this is not just a video game -- it is a video/audio game investment. Far more effort was put into the sounds of this game than is put into most other arcade games. If the speakers are not up to it, replace them. A small investment in good speakers can make a world of difference in profits. Competent and reasonably priced speakers can be obtained from stores such as Radio Shack.
  • Wire the coin doors and the test / service switch(es) as per the JAMMA Harness Connection table on page 26.
  • Connect the door lamps to the +12 vde supply. Some games have separate power supply outputs for the lamps.
  • Install a test switch somewhere convenient inside the coin door area. This switch allows you to enter adjustables, run diagnostics, and see or clear audits. Make it readily accessible through the coin door. Wire it to the Test wire on the JAMMA Harness.
  • Install a service switch (not _ included) somewhere convenient inside the coin door area. This switch allows you to give credits to players without affecting the game’s credit audits or coin meters. Example: A player puts in a coin and gets no credit, the operator can then push the service button and a credit is given to the player without affecting the game’s audits and coin meter.

LS 8 - GOLDEN TEE 3D GOLF

Page 11
  • GOLDEN TEE 3D GOLF has the ability to adjust volume at any time during a game. Install 2 push button switches (NOT INCLUDED) inside the coin door for easy access. Connect the switches to the JAMMA harness. Refer to the JAMMA Harness Connection diagram on page 26.

GOLDEN TEE 3D GOLF is also capable of running a Mars Light or other external signal, which will be activated if the game is running a special Hole-in-One contest.

MARS LIGHT HOOKUP

Equipment required. A mars light police beacon and a3 amp 120 volt AC solid state relay with a 2.5 to 8 volt control line.

1. Connect a wire from pin 2 of the sound boards ticket connector to the positive control line of the Relay.

Connect a wire from pin 3 of the sound boards ticket connector to the negative control line of the Relay.

The hot AC line in should connect to one side of the light and the return should connect to the AC input of the relay.

From the AC output of the relay, connect a wire to the other side of the light.

The hole-in-one contest turned on in operator adjustables in order for the light to activate when a hole-in-one is made.

NOTE:

Mars Light will only work for sound PROMS 1.2 and above.

FINAL CHECK:

1. Check the game inside and out for any imperfections. Secure any loose wiring or fastening hardware.

Make sure the coin door is tight and the coin mechs are well adjusted.

Make sure all assemblies are firmly attached. Anything that is not mounted securely will rattle when the game is played. This game makes use of low-frequency sounds which can cause any loose joints to rattle.

INITIAL START-UP

  • Attach JAMMA Harness. Plug in the game and turn it on.
WARNING! - Make sure the hamess is plugged in correctly. Damage to PCB will occur if JAMMA connector is plugged in wrong.
  • Look and smell for smoke (TURN IT OFF IMMEDIATELY IF ANY IS NOTICED).
NOTE: Readjust the +5 Volt supply. Adjust the +5 Volt supply 0 that you read 5.2 Volts across an I.C. on the circuit board. If measured at the power supply, the reading will be higher at the power supply outputs.
  • Make sure the yellow LED on the Sound PCB is flashing. If not, something is wrong, turn off the game.

4, Listen for sound. Sounds should be heard in the attract mode.

  • If you do not hear any sounds and the yellow LED is flashing, try turning up the volume and check the speaker connections. Dropping a coin through a coin switch should cause a sound.
  • How is the picture? Is it centered or is it too bright or too Is it in focus? Adjust your monitor to get the best picture possible.
NOTE: Check your monitor manual to make adjustments. Some test patterns are available through the game's system tests by pressing the Test switch. Use them when making any adjustments. (See SYSTEM TESTS information on page 12. Proper monitor adjustment is very important.)

GOLDEN TEE 3D GOLF - 9

Page 12
  • Try all coin switches. Drop quarters or tokens through to check the coin mechs. Make sure the game is adding credits. You can use the Player Control Tests by pressing the test switch and entering the SYSTEM TEST MENU. Do all of the controls work? Try playing the game with the volume up and listen for rattling as you play. Tighten anything that is making noise.
  • Upon initial power-up, the game will initialize to factory default settings. These settings affect game elements such as number of credits per coin, difficulty settings, etc. The OPERATOR ADJUSTABLES MODE section will describe how to alter these settings and view the system audits or run system tests.

DIP SWITCH SETTINGS

The main dip switches can be found on the main board near the fuse.

Dip switch 4 (ON): Always “ON" (DEFAULT) Dip switch 4 (OFF): *** NOT USED *** Dip switch 3 (ON): Trackball normal (DEFAULT) Dip switch 3(OFF): Trackball mounted at 45° angle. Dip switch 2 (ON): One Trackball (DEFAULT) Dip switch 2 (OFF): Two Trackballs Dip switch 1 (ON): Normal Game Play (DEFAULT) Dip switch 1 (OFF): Operator Mode Menu

There are also dip switches on the memory board near the green LED. Switches #1 and #2 must be “ON” and switches #3 and #4 must be “OFF”

10 - GOLDEN TEE 3D GOLF

OPERATOR MODE

To enter the OPERATOR MODE MENU, press the Test Button, located just inside the coin door. When the Test Button is pressed or DIP Switch 1 is flipped to the OFF position, the screen displays the OPERATOR MODE MENU.

NOTE:

If you used DIP switch 1 to enter the OPERATOR MODE MENU, you will need to flip DIP switch 1 back to the ON position in order to return to the game.

GOLDEN TEE 3-D GOLF v1.00

TRACKBALL UP TO MOVE UP ‘TRACKBALL DOWN TO MOVE DOWN PRESS START.TO CHOOSE

OPERATOR MODE MENU.

exit

VOLUME SETTINGS

OPERATOR ADJUSTABLES MENU

GAME AUDITS MENU

SYSTEM TESTS MENU

OPERATOR MODE MENU

The OPERATOR MODE MENU allows you to enter into four different areas:

VOLUME SETTINGS is used to adjust the volume of your game for your location.

OPERATOR ADJUSTABLES is used for customizing your game for your location. Some of the features in Operator Adjustables are number of coins per game, sounds on or off when no one is playing, difficulty settings, etc.

GAME AUDITS allows you to check your game's overall earnings, game times, game scores, etc. The Audits can be reset through this menu as well.

SYSTEM TESTS verifies the operation of the hardware, controls, and monitor through easy and automatic procedures accessed through these menus.

Page 13

Menu items can be highlighted using the trackball or FACE LEFT and FACE RIGHT buttons. When using the trackball, menu items are highlighted by rolling the trackball up or down. To select a highlighted item, press the START button.

To exit any of these tests and return the game to its normal state, use the trackball or FACE LEFT and FACE RIGHT button to highlight the line that says EXIT, and press the START button.

COLOR KEY NOTE:

For easy identification, all test screens have been color coded. items displayed in GREEN are the Menu titles. This is the name of the menu that is currently displayed. Items appearing in YELLOW are the menu's instructions. The Light BLUE items are choices available in this menu. The PURPLE item is the selection that is currently highlighted. If RED is ever displayed, there is a problem with that item and it should be corrected.

VOLUME SETTINGS

The VOLUME SETTINGS screen is used to adjust the sounds that are heard during game play.

TO EXIT PRESS START.

wer

MOVE TRACKBALL RIGHT TO INCREASE VOLUME

MOVE TRACKBALL LEFT TO DECREASE VOLUME

VOLUME SETTINGS SCREEN

When this screen appears, music will play. Move the trackball to the right to increase the game’s sounds and music. Rolling the trackball to the left will make the game sounds softer. When you have adjusted the sounds to the appropriate volume, press the START button to exit back to the main menu.

The volume can also be set using optional volume up/down push button switches. See page 8 for more information on this feature.

OPERATOR

_ ADJUSTABLES

The OPERATOR ADJUSTABLES MENU _ is accessed through the OPERATOR MODE MENU. From the OPERATOR MODE MENU, roll the

trackballdownoruptohighlight thewords

OPERATOR ADJUSTABLES MENU which will then appear in purple letters. Now press the START button, and the OPERATOR ADJUSTABLES MENU will appear on the screen.

GOLDEN TEE 3-D GOLF v1.00

TRACKBALL UP TO MOVE UP TRACKBALL DOWN TO MOVE DOWN START TO CHOOSE

OPERATOR ADJUSTABLES MENU.

EXIT ADJUSTABLES

GAME MODE SELECTION

GAME RESETS

ATTRACT MODE SOUNDS,

CREDITS AND COIN DOOR SETTINGS

DELAY TIME ADJUSTMENT.

SKILL LEVEL ADJUSTMENT

HOLE IN ONE CONTEST MODE

OPERATOR ADJUSTABLES MENU

Asyoucansee,therearemanypossible

customizing procedures that you can control. Below is a brief description of each adjustable function and

whatthescreenlookslikewhendisplayed.

Remember, to select an item from any menu, using the trackball to highlight the item in purple, and then press the START button.

GAME MODE SELECTION:

This menu allows you to place the game in standard Coin Mode, or choose Free Play.

GOLDEN TEE 3-D GOLF v1.00

TRACKBALL UP TO MOVE UP ‘TRACKBALL DOWN TO MOVE DOWN PRESS START TO CHOOSE

‘GAME MODE SELECTION

COIN MODE

FREE PLAY

GAME MODE SELECTION SCREEN

In COIN MODE, the game will only work if coins are deposited into the game.

GOLDEN TEE 3D GOLF -* —

Page 14

In FREE PLAY, coins are not needed for play, and the START button is always active.

Game RESETS:

The GAME RESETS menu will cancel or zero out any custom features or bookkeeping figures that are no longer wanted.

GOLDEN TEE 3-D GOLF v1.00

‘TRACKBALL UP TO MOVE UP ‘TRACKBALL DOWN TO MOVE DOWN

PRESS START TO CHOOSE

GAME RESETS:

EXIT RESETS

RESET ALL TO FACTORY SETTINGS

RESET HIGH SCORES ONLY

RESET AUDITS ONLY

GAME RESETS MENU

RESET ALL TO FACTORY SETTINGS will change the game back to the way the game was preset when new. Any custom features such as Free Play and Skill Levels will be changed back to the original settings set at the factory.

RESET HIGH SCORES ONLY is used to erase all of the high scores stored in memory.

RESET AUDITS ONLY is used when all of your bookkeeping and statistics have been gathered from the Audits section, and are no longer needed. If you like to gather all of your accounting information each week, or after each collection, it is a good practice to reset all of the audits so your coin count will match the audit information.

ATTRACT MODE Sounbs:

OCCASIONAL ATTRACT MODE SOUNDS plays sounds about every ten to twelve times the attract mode is repeated.

ALL ATTRACT MODE SOUNDS OFF will not allow any sounds to be played during the attract mode.

CREDITS AND COIN DooR SETTINGS:

This menu is used to adjust the sounds that are heard while no one is playing the game.

GOLDEN TEE 3-D GOLF v1.00

TRACKBALL UP TO MOVE UP ‘TRACKBALL DOWN TO MOVE DOWN

ATTRACT MODE SOUNDS:

ALL ATTRACT MODE SOUNDS ON

OCCASIONAL ATTRACT MODE SOUNDS

ALL ATTRACT MODE SOUNDS OFF

ATTRACT MODE SOUNDS MENU

ALL ATTRACT MODE SOUNDS ON will play sounds during every attract cycle. This menu allows you to change the number of coins needed to play GOLDEN TEE 3-D GOLF.

GOLDEN TEE 3-D GOLF v1.00

TRACKBALL UP TO MOVE UP TRACKBALL DOWN TO MOVE DOWN

CREDITS AND COIN DOOR SETTINGS

EXIT CREDITS AND COIN DOOR SETTINGS

DOOR + COIN VALUE i

DOOR 2 COIN VALUE i

DOOR 3 GOIN VALUE i

COINS NEEDED FOR ONE CREDIT 2

HOLES PLAYED PER CREDIT. 3

COINS NEEDED TO PLAY 18HOLES 10

‘TO CHANGE VALUES MOVE TRACKBALL LEFT TO DECREASE MOVE TRACKBALL RIGHT TO INCREASE

CREDIT AND COIN DOOR SETTING SCREEN

You can set each door to different coins values by highlighting : DOOR 1 COIN VALUE for coin door 1, DOOR 2 COIN VALUE for coin door 2, etc.. Moving Trackball left or right will change the number of credits that each coin represents.

COINS NEEDED FOR ONE CREDIT.....To award a game credit, the player will need to insert an adjustable number of coins.

HOLES PLAYED PER CREDIT.....This defines the number of holes the player is given for each credit. This value can range from 1 to 3 holes.

COINS NEEDED TO PLAY 18 HOLES.....To play an entire 18 holes at a reduced cost to the player, you can set this value to something less than the cost of buying holes as described above. The default is 10 coins for 18 holes. This is a savings of 2 coins, at a rate of 2 coins for 3 holes. The player will need to insert all 10 coins at the start of a game to take advantage of this.

“12 - GOLDEN TEE 3D GOLF

Page 15

DELAY TIME ADJUSTMENT:

This option allows for changing the delay of game time.

GOLDEN TEE 3-D GOLF v1.00

TRACKBALL UP TO MOVE UP TRACKBALL DOWN TO MOVE DOWN ART TO CHOOSE

DELAY TIME ADJUSTMENT

EXIT DELAY TIME ADJUSTMENT

DELAY OF GAME TIMEOUT 0:25

DELAY OF GAME TIMEOUT ON/OFF

TO CHANGE VALUES MOVE TRACKBALL LEFT TO DECREASE

MOVE TRACKBALL RIGHT TO INCREASE

BUTTON CONFIGURATIONS SCREEN

DELAY OF GAME TIMEOUT (1).....The game will give the player a penalty stroke if they have not swung the club after this amount of time.

DELAY OF GAME TIMEOUT (2). he timeout can be disabled by selecting “OFF” - The default is “ON”. We recommend leaving this “ON” so the game will return to the attract mode if a player walks away from a game in progress.

SKILL LEVEL ADJUSTMENT:

GOLDEN TEE 3-D GOLF allows for changing the level of skill needed to play the game. This feature is good for locations with younger or novice players who are less skilled at the game, or expert or accomplished players who demand a_ greater challenge.

GOLDEN TEE 3-D GOLF v1.00

‘TRACKBALL UP TO MOVE UP ‘TRACKBALL DOWN TO MOVE DOWN PRESS START TO CHOOSE

SKILL LEVEL ADJUSTMENT.

SKILLLEVEL A EASIEST

SKILL LEVEL 2

SKILL LEVEL 3

SKILL LEVEL 4

SKILL LEVEL 5 = HARDEST

SKILL LEVEL ADJUSTMENT SCREEN

To set the game to an easy skill level, highlight... SKILL LEVEL 1 - EASIEST.

To set the game to a difficult skill level, highlight...SKILL LEVEL 5 - HARDEST. SKILL LEVEL 2, SKILL LEVEL 3, and SKILL LEVEL 4 are settings between the easiest and hardest levels. Sometimes it is best if the skill level is adjusted gradually over a period of time.

HOLE IN ONE CONTEST MODE

The HOLE IN ONE CONTEST MODE can be used if your location wants to give away prizes for a hole-in-one.

GOLDEN TEE 3-D GOLF v1.00 _

TRACKBALL UP TO MOVE UP TRACKBALL DOWN TO MOVE DOWN PRESS START TO CHOOSE

NO HOLE iN ONE CONTEST

HOLE IN ONE CONTEST. - WIN IMMEDIATELY HOLE IN ONE CONTEST - QUALIFY TO WIN,

HOLE IN ONE CONTEST MODE SCREEN

Setting the HOLE-IN-ONE CONTEST “ON” will cause a loud siren and fanfare to go off if a hole-inone is made. The hole-in-one message can be altered depending on your type of contest.

HOLE IN ONE CONTEST - WIN IMMEDIATELY will display a “YOU HAVE WON” message.

HOLE IN ONE CONTEST - QUALIFY TO WIN will display a “YOU HAVE QUALIFIED” message.

GOLDEN TEE 3D GOLF - 13

Page 16

GAME AUDITS

The GAME AUDITS MENU will supply you with a

detailedaccountingofhelpfulandinformative

bookkeeping and statistics. To enter the GAME AUDITS MENU, first go to the OPERATOR MODE MENU by pressing the test switch located just inside the coin door of the cabinet or flip DIP switch 1 to

the OFF positionontheMainPCB.Fromthe

OPERATOR MODE MENU, press FACE RIGHT or

FACELEFTuntiltheGAMEAUDITSMENU

appears in white letters. Now press the START button, and the GAME AUDITS MENU will appear on the screen.

GOLDEN TEE 3-0 GOLF V1.00

TRACKBALL UP TO MOVE UP. TRACKBALL DOWN TO MOVE DOWN PRESS START TO CHOOSE

GAME AUDITS MENU

EXIT AUDITS

DISPLAY COIN AUDITS

DISPLAY GAME SELECTION AUDITS

NUMBER OF GOLFERS AND HOLES PLAYED

OAK VALLEY AUDITS

OCEAN POINTE AUDITS

CACTUS CANYON AUDITS

RESET AUDITS

GAME AUDITS SCREEN

DISPLAY COIN AUDITS:

When you choose to review the coin audits, the DISPLAY COIN AUDITS screen will appear.

GOLDEN TEE 3-D GOLF v1.00

PRESS STAAT TO EXiT

DISPLAY COIN AUDITS

COIN DOOR 7 COINS

GOIN DOOR 2 COINS

COIN DOOR 3 COINS

TOTAL COINS

TOTAL GAMES STARTED

SECONDS PER COIN

DISPLAY COIN AUDITS SCREEN

14 - GOLDEN TEE 3D GOLF

DISPLAY GAME SELECTION AUDITS:

This menu will show the audits for each game selection.

GOLDEN TEE 3-D GOLF v1.00

PRESS START TO EXIT

DISPLAY GAME SELECTION AUDITS

STROKE GAMES

SKINS GAMES

OAK VALLEY COURSE

OCEAN BOINTE COURSE

CACTUS CANYON COURSE

FORWARD ONLY STROKES

DISPLAY GAME SELECTION AUDITS SCREEN

NUMBER OF GOLFERS AND HOLES PLAYED:

This menu displays how many games were played by 1, 2, 3, or 4 players and how may holes were played during a game.

GOLDEN TEE 3-0 GOLF V1.00

PRESS START TO EXIT

NUMBER OF GOLFERS AND HOLES PLAYED

TOTAL 1 GOLFER GAMES xx

TOTAL? GOLFER GAMES xX

TOTAL 3 GOLFER GAMES xx

TOTAL 4 GOLFER GAMES XX

TOTAL 1-8 HOLE GAMES: XX

TOTAL 9-17 HOLE GAMES. XX

TOTAL 18 HOLE GAMES xx

NUMBER OF GOLFERS AND HOLES PLAYED SCREEN

Page 17

OaK VALLEY AUDITS:

Cactus CANYON AUDITS:

This menu displays the audits for the Oak Valley

course.

GOLDEN TEE 3-D GOLF v1.00

PRESS START TO EXIT

‘OAK VALLEY AUDITS

TOTAL GAMES:

TOTAL HOLES PLAYED

AVERAGE HOLES PER GAME

TOTAL STROKES

TOTAL PUTTS

TOTAL WATER OR UNPLAVABLE BALLS

TOTAL OUT OF BOUNDS SHOTS

"TOTAL DELAY OF GAMES

OAK VALLEY AUDITS SCREEN

OCEAN POINTE AUDITS:

ThismenuwilldisplaytheauditsfortheCactus

Canyon course.

GOLDEN TEE 3-D GOLF V1.00

PRESS START TO EXIT

‘CACTUS CANYON AUDITS

TOTAL GAMES

TOTAL HOLES PLAYED

AVERAGE HOLES PER GAME

TOTAL STROKES.

TOTAL PUTTS

TOTAL WATER OR UNPLAYABLE BALLS

‘TOTAL OUT OF BOUNDS SHOTS

TOTAL DELAY OF GAMES

CACTUS CANYON AUDITS SCREEN

RESET AUDITS :

This menu displays the audits for the Ocean Pointe

course.

GOLDEN TEE 3-D GOLF v1.00

PRESS START TO EXIT

OCEAN POINTE AUDITS

TOTAL GAMES:

TOTAL HOLES PLAYED

AVERAGE HOLES PER GAME

TOTAL STROKES

TOTAL PUTTS

TOTAL WATER OR UNPLAYABLE BALLS

FOTAL OUT OF BOUNDS SHOTS

TOTAL DELAY OF GAMES

OCEAN POINTE AUDITS SCREEN This menu will reset your audits.

GOLDEN TEE 3-D GOLF v1.00

‘TRACKBALL UP TO MOVE UP TRACKBALL DOWN TO MOVE DOWN PRESS START TO CHOOSE

RESET AUDITS

NO RESET AUDITS

RESET AUDITS

GAME RESETS SCREEN

If you wish to set all of the game audits (described above) back to zero, highlight RESET AUDITS from this menu and press the START button. The screen

will briefly display AUDIT RESET.

If you change your mind and decide not to reset the

auditstozero,highlightNORESET AUDITS and
youwillexitthisscreenwithoutmakingany

changes.

eT GOLDEN TEE 3D GOLF - 15

Page 18

SYSTEM TESTS

GOLDEN TEE 3-D GOLF has been inspected and tested at the factory, and most likely the game will be in perfect working order when you plug it in. If you are experiencing any problems with the game, the SYSTEM TESTS MENU is a good place to start when tracking down the problem. To enter the SYSTEM TESTS MENU, first go to the OPERATOR MODE MENU by pressing the test switch located just inside the coin door of the cabinet, or set DIP Switch 1 on the Main PCB to the OFF position. From the OPERATOR MODE MENU, roll the trackball up or down until the word SYSTEM TESTS MENU appears in purple letters. Now press the START button, and the SYSTEM TESTS MENU will appear on the screen.

GOLDEN TEE 3-D GOLF V1.00

‘TRACKBALL UP TO MOVE UP ‘TRACKBALL DOWN TO MOVE DOWN. PRESS START TO CHOOSE

SYSTEM TESTS MENU

EXIT TESTS

VIDEO SCREEN TESTS

FULL GROM CHECKSUM TEST

FAST GROM CHECKSUM TEST

VIDEO RAM TEST

PALETTE RAM TEST

BOARD TESTS

SOUND TEST

PLAYER CONTROLS TEST

SYSTEM TESTS MENU

VIDEO SCREEN TESTS :

You can test your monitor and adjust colors by choosing VIDEO SCREEN TESTS and pressing the START button.

GOLDEN TEE 3-D GOLF V1.00

VIDEO SCREEN TEST

TO VIEW VIDEO TEST SCREENS

PRESS FACE LEFT OR RIGHT BUTTONS. PRESS START AT ANY SCREEN TO EXIT

FOLLOWING SCREENS ARE AVAILABLE

COLOR ADJUSTMENT SCREEN GRID PATTERN. RED SCREEN GREEN SCREEN BLUE SCREEN WHITE SCREEN

VIDEO SCREEN TEST MENU When the FACE LEFT or FACE RIGHT buttons are pressed, the screen changes to display a grid of colored rectangles. Use these colors as a guide and adjust your monitor so they look as good as possible. This test can be exited at any time by pressing the START button.

FULL GROM CHECKSuM TEST:

Choose FULL GROM CHECKSUM TEST from the SYSTEM TEST MENU to test the Graphics chips on the PCB. This test performs a complete test of the Graphics ROM’s. While the test is in progress the following message is displayed:

FULL GROM CHECKSUM TEST SCREEN (TEST IN PROGRESS)

When the test is completed the GROM Test Screen is displayed.

GOLDEN TEE 8-D GOLF V1.00

FULL GROM CHECKSUM TEST

FULL GROM CHECKSUM TEST: (PASSED or FAILED)

PRESS START BUTTON 70 EXIT. PRESS LEFT BUTTON TO LOOP TEST

FULL GROM CHECKSUM TEST SCREEN (TEST COMPLETED)

  • If all checksums are shown in blue, the test passed and your game is in good working order.
  • If any checksums are bad, they will be displayed in red text on this screen. This means that the GROM is defective and needs to be replaced. Call your distributor or the Incredible Technologies, Inc. Service Department for further help.
  • To exit this test, press the START button.

16 - GOLDEN TEE 3D GOLF

Page 19

Fast GROM CHECKSUM TEST:

VIDEO RAM TEST:

Choose FAST GROM CHECKSUM TEST from the SYSTEM TEST MENU to test the Graphics chips on the PCB. This test performs a complete test of the Graphics ROM’s. While the test is in progress the following message is displayed:

FAST GROM CHECKSUM SCREEN (TEST IN PROGRESS)

When the test is completed the GROM Test Screen is displayed.

GOLDEN TEE 3-D GOLF V1.00

FAST GROM CHECKSUM TEST

PRESS START BUTTON TO EXIT PRESS LEFT BUTTON TO LOOP TEST

FAST GROM CHECKSUM TEST SCREEN (TEST COMPLETED)

  • If all checksums are shown in white, the test passed and your game is in good working order.
  • If any checksums are bad, they will be displayed in red text on this screen. This means that the GROM is defective and needs to be replaced. Call your distributor or the Incredible Technologies, Inc. Service Department for further help.
  • To exit this test, press the START button. This test performs a complete test of the Graphics video RAM. The video RAM is tested in two pages. The following message will be displayed as each page is tested.
Whenthe testiscompletedtheresultswillbe

displayed as follows.

GOLDEN TEE 3-D GOLF v1.00

VIDEO RAM TEST_

VIDEO PLANE A PAGE 0 STATUS = 0000

VIDEO PLANE A PAGE 1 STATUS = 0000 VIDEO PLANE 6 PAGE 0 STATUS = 0000 VIDEO PLANE 8 PAGE 1 STATUS = 0000

Us2 GOODU3 GOOD_U30 GOOD_us1 GOOD

‘VIDEO RAM TEST [PASSED or FAILED]

PRESS START BUTTON TO EXIT. PRESS LEFT BUTTON TO LOOP TEST

VIDEO RAM TEST SCREEN

14.Ifthegamepassesthistest,zeroswillbe

displayed in white along with a VIDEO RAM TEST PASSED message.

  • If the test fails, a non-zero status and VIDEO RAM TEST FAILED message will be displayed in red. Call your distributor or the Incredible
Technologies,Inc.ServiceDepartmentfor

further help.

  • To exit this test, press the START button.

PALETTE RAM TEST:

GOLDEN TEE 3-D GOLF V1.00

PALETTE RAM TEST

PALETTE RAM STATUS = 0000

RED GOOD. GREEN GOOD BLUE GOOD

PALETTE RAM TEST (PASSED or FAILED)

PRESS START BUTTON TO EXIT. PRESS LEFT BUTTON TO LOOP TEST

PALETTE RAM TEST SCREEN

Eee eae Taal GOLDEN TEE 3D GOLF - 17

Page 20

BOARD TESTS :

CONTROL PANEL TEST:

This test will perform all of the system's tests at one time.

PROGRAM MEMORY U45-U48 (GOOD or BAD)

PALETTE RAM TEST RED GOOD GREEN GOOD _BLUE GOOD PALETTE RAM TEST (PASSED or FAILED)

VIDEO RAM TEST us2 GOOD _U35 GOOD _U30 GOOD 31 GOOD VIDEO RAM TEST [PASSED or FAILED]

GROM TesT

oe ‘ra 200000 320000 200008

FAST GROM CHECKSUM TEST (PASSED or FAILED) 'TTBOARD TEST (PASSED or FAILED) I!

BOARD TESTS SCREEN

SOUND TESTS:

Choose SOUND TEST from the SYSTEM TEST MENU to test the sounds and speakers in the game. The sound section also controls the coin meter, and you can test it from this section as well.

GOLDEN TEE 3-D GOLF V1.00

TRACKBALL UP TO MOVE UP ‘TRACKBALL DOWN TO MOVE DOWN PRESS START TO CHOOSE

SOUND TESTS

COIN METER TEST

TEST ALL SOUND ROMS

ROMO = DRUMS AND PERCUSSION SROMi_~ BROKEN GLASS SOMA _- FABULOUS SHOT SROWS_- GOLF SWING

HOLE IN ONE EVENT

MUSIC

SOUND TESTS SCREEN

To test the coin meter, choose COIN METER TEST from this menu. If everything is working properly, the meter should increment each time the START button is pressed while this line is highlighted.

18 - GOLDEN TEE 3D GOLF When CONTROL PANEL TEST is selected, the screen will display a diagram of a typical GOLDEN TEE 3D GOLF control panel. The controls are highlighted on the diagram when the controls are active. Test all of the controls, including coin test and service switches. Press FACE LEFT and FACE RIGHT together to exit this test.

Golden Tee 3D Golf Pla Cont

CONTROL PANEL TEST SCREEN

NOTE:

For cabinets with 2 sets of player controls, two separate player control tests will appear in the SYSTEM TESTS MENU.

Page 21

LS GOLDEN TEE 3D GOLF - 19

Page 22

APPENDIX A

20 - GOLDEN TEE 3D GOLF

Page 23

VIDEO PROBLEMS

Symptom Probable Cause Solution

No pictureDip switches on the memoryDip switches 1 and 2 must be ‘ON’,

board improperly set. and 3 and 4 must be ‘OFF’

Bad connections or video Make sure there are good inputs are not hooked up connections from the board's video properly. outputs to the monitor's video inputs.

Monitor Make sure the monitor is operating correctly. (Check it with another compatible logic board.)

JAMMA harness connected Identify Pin 1 on the JAMMA improperly connector and on the PCB. If installed incorrectly, damage to the PCB may have occurred.

Scrambled PictureMissing sync connection orCheck the sync connection - Adjust

misadjusted monitor monitor.

Monitor out of sync and can notNeed a 75 ohm pull-up resistorSolder a 75 ohm resistor across D9
be adjusted.on the sync line.located on the main board.
Missing colors or a washed outBad video connectionsCheck the video red, green, and

color blue connections.

Bright, blurry, or rolling pictureMisadjusted monitorAdjust the monitor, not the board.

(Refer to your monitor manual.)

Picture too large, too small, orMisadjusted monitorAdjust the monitor, not the board.

off center (Refer to your monitor manual.)

Video image is flippedMisadjusted MonitorChange Dip Switch 3 on the Main

PC board or reverse the monitor's convergence wires. (Refer to your monitor manual.)

Bad images in pictureBad GROMDo GROM test. Check IC pins to

make sure none are bent over.

Diagonal white linesGND problemEarth and Logic GND's should be

connected at the power supply.

i UE EEE Tere ae GOLDEN TEE 3D GOLF - 21

Page 24

SOUND PROBLEMS

Symptom Probable Cause Solution

No Sound +12v power supply is bad Try another +12v power supply.

Bad connection to the board Check for +12v power on the board.

Check for +5v power on the board.

Check the volume setting in the OPERATORS ADJUSTABLE section of the Operators Mode.

Check the speaker connections.

JAMMA harness connected Identify Pin 1 on the JAMMA improperly connector and on the PCB. If installed incorrectly, damage to the PCB may have occurred.

Miscellaneous Make sure the sound status light is flashing on the board.

22 - GOLDEN TEE 3D GOLF

Page 25

CONTROL PROBLEMS

Symptom Probable Cause Solution

Buttons do not work or are partly inoperable

Coin counter not working

Trackball mounted correctly but is swinging 45° out of line

In a two or more player game, controls only work for players 1 and 3. Switches not properly connected

JAMMA harness connected improperly

Miscellaneous

DIP switch 3 found on the Main Board is not “ON”.

On the Main Board DIP switch 2 is in the “OFF” position. Make sure that the common post of the switch is connected to ground.

Make sure each individual switch is working by doing the Control Panel Test found in the SYSTEM TESTS section.

Make sure that the signal wire for that particular switch is connected to the normally open post of the switch.

Identify Pin 1 on the JAMMA connector and on the PCB. If installed incorrectly, damage to the PCB may have occurred.

Make sure that the signal wire has aconnection from the switch to the board.

Make sure +12v is hooked up to the counter.

The signal wire is not connected to coin counter. (Check continuity.)

Verify that the counter is good.

Make sure the DIP switch 3 is “ON”

DIP switch 2 must be in the “ON” position for cabinets with one set of player controls.

i TEE EEE ST Ee=r eager

GOLDEN TEE 3D GOLF - 23

Page 26

WER-UP PROBLEMS

Symptom Probable Cause Solution

No reaction when game is Blown fuse Power supply is too high. Power turned on should be between +5v & 5.2v. (Measured on the circuit board.)

Cabinet is not connected to earth ground. (All metal should be connected to the earth ground.)

Short between power and ground. Check for foreign material.

Disconnect the harness and measure the resistance between power and ground. It should read around 600 ohms. (0 ohms is a dead short.)

Make sure the hamess is not shorting to anything, such as bare or frayed wires shorting out each other or hitting bare metal.

No power from the power Replace power supply. supply

Power supply Power supply too low. (should ideally be between +5v & +5.2v.) (Measured on the circuit board.)

Short on the board Check for loose or foreign material on the board.

JAMMA harness connected Identify Pin 1 on the JAMMA improperly connector and on the PCB. If installed incorrectly, damage to the PCB may have occurred.

Screen flashes repeatedly Open on socketed IC's Check for bent pins on socketed parts.

Make sure that all IC's are seated in their sockets properly.

+5v setting too low Check voltage. (Measured on the circuit board.)

DIP switch on the memory Make sure dip switch #1 and #2 board may not be set correctly. are “ON”, and #3 and #4 are “OFF” on the memory board.

24 - GOLDEN TEE 3D GOLF

Page 27

MISCELLANEOUS PROBLEMS

Symptom Probable Cause Solution

Green L.E.D. not blinking

Operator adjustables keep changing

Sounds bad

Game comes up in Test Mode

Trackball mounted correctly but is swinging 45° out of line.

ST GOLDEN TEE 3D GOLF - 25 Program not running

No power

Bad connections

Loose pin on ASIC (U1)

Low battery voltage

Bad static RAM

Miscellaneous

Dip Switch 1 is “OFF”

Dip switch 3 found on the Main board is not “ON”. Make sure all socketed I.C.'s are seated correctly. Look for bent pins.

Blown fuse. Check for +5v before and after the fuse. Adjust power supply for +5v after the fuse. Use fast blow fuses only.

Make sure you have continuity from PCB to power supply.

Call Incredible Technologies, Inc.

Battery should be 2 to 3 volts.

Replace.

Check the speaker connections.

Make sure Dip Switch 1, on the Main PC board, is in the “ON” position.

Make sure the Dip switch 3 is “ON”.

Page 28

APPENDIX B

26 - GOLDEN TEE 3D GOLF

Page 29

JAMMA Harness Connection for Golden Tee 3D Golf

WIRE COLOR PARTS SIDE

Black GND

Black GND

Red +5 vde

Red +5 vde

Orange +12 vde KEY

Yellow-Green Left Speaker (-)

Green-Black Video Green White Video Sync

Orange-Black Service

Green-Blue Coin2

Orange-Yellow Volume Down

Gray-Yellow Call in button

Black GND

Black GND A

B

Cc

D

E

F

H

J

K

L

M

N

P

R

s

T

U

Vv

w

x

Y

z

a

b

c

d

e

f SOLDER SIDE WIRE COLOR

ieGNDBlack
pgGNDBlack
cme+5 vdcRed
ci+5 vdeRed
(ae+12 vdeOrange

7 KEY

fgCoin CounterRed-Green

Left Speaker (+) Yellow-Red

Video Red Red-Black

Video Blue Blue-Black

Video GND White-Black

Test Blue

Coin 1 Red-Blue

Start 1 Red-White

Player - Face Left__| Brown-White Player - Face Right_| Yellow-White Volume Up Orange-White Coin 3 Gray-White

GND Black

GND Black

Trackball Cable Connection

PIN WIRE #6 - Black Memory Board Connector Trackball Connector

PIN WIRE #1 - Black

PIN WIRE #1 - Red PIN WIRE #2 - Red

PIN WIRE #2 - Yellow PIN WIRE #3 - Yellow

PIN WIRE #3 - Green PIN WIRE #4 - Green

PIN WIRE #5 - Blue PIN WIRE #5 - Blue

PIN WIRE #4 - Purple PIN WIRE #6 - Purple

NOTE: Remember to connect the trackball cable to JP9 of the Memory Board. (Labeled as Player 1)

SUE UNEIEIEEEEEEESEEEEEE SERRE eee a GOLDEN TEE 3D GOLF - 27

Page 30

28 - GOLDEN TEE 3D GOLF

Page 31

INCREDIBLE TECHNOLOGIES, INC.

SERVICE / SALES (800) 262-0323 FAX (708) 870-0120

Hardware and Software ©Copyright 1995 Incredible Technologies, Inc. All rights reserved.

Page 32

Incredible Technologies, Inc. 4010 Winnetka Avenue

Rolling Meadows, IL 60008

(708) 870-7027 Bs wy

{