CATHODE RAY TOMES

Trojan

Trojan (US set 1) (Capcom, 1986) · Manual · 16 pages · 18 sections · original scan

Page 1

Licensed From CAPCOM ™ All Rights Reserved ©1986 = rs

wn s 3 c S

g = 25

c eet

i] Qe 2 z $ 8 & 3

mm ROMSTAR inc.

Phone (213) 53%+2744 Fax (213) 539-3626 Telex 182426

Page 2

Before You Get Started. . .Stop!

Does your new game package include all listed parts? (Is it complete?)

  • Isthe game you have chosen to transform able to supply all the required voltages for the new game?
Note: Some games, (i.e. Ms. Pac Man, Galaxian, etc.} regulate their voltages on the main PC.B. This makes the existing power supply inefficient. These games will require a change in power supply for your new game. Many game supply houses can offer you a switching regulated power supply for a relatively low cost.
  • Is the monitor configuration compatible? In most games it is rather difficult to change the monitor from a vertical mount to a horizontal mount. We recommend you choose a game cabinet with the same mount as your new game requires.
  • Do you have the necessary tools? (See the recommended tool list)

Caution

F.C.C. Regulation Compliance

The PC. board cage supplied with this new game kit must be utilized and terminated to ground at the time of installation. This is to avoid radio frequency radiation and comply with the limits for a class “A” computing device pursuant to sub-part ‘J’ of part 15 of F.C.C. rules, which are designed to provide reasonable protection against interference when operated ina commercial environment. Operation of this equipment in a residential area is likely to cause interference

  • in which case, the user at his own expense, will be required to take whatever measures may be required to correct the interference.
Page 3

Installing and Servicing Your

TROJAN

New Game Package

Table of Contents

New Game Package Contents... ... 0.660000. 0 cece eee cece eee 2

Power and Monitor Requirements... 0... .0 0.0 c cece ete eens 2

Recommended Tools and Supplies... 0.2.2.0... 00sec cece eee eee 3 DIPISWIECH. TADIOS «.. 0. ones csee we seme eco Be ek HEH Hae BOIS woes ations bee g 3&4 GaMe OPETAION «+ sie s sins s ste a Hah | ETE HOeE daikon w oays Fgh, 8 wspapere Sgene @ eran 5

Installation Procedures «0.2... 6c cette 6

Control: PamelPOsitiOming: ys x yee ee eee wave s tonend € aie F Sides FE Eiia SPORES | 12

Main Harness Connections ..... 0.0.0 e cee cece eee teens outside back cover

Page 4

TROJAN

NEW GAME PACKAGE CONTENTS

1 Main Printed Circuit Board (PCB) 1 Marquee 1 PCB Cage (FCC Required) 1 Control Panel Overlay 1 Set Legs, Bolts, & Spacers 1 Plex Control Cover 1 Connecting Wire Harness 1 Set Side Graphics 1 Eight-Way Joystick 1 Set Play Instructions & Function Labels 6 Player Button Assemblies 1 Service and Installation Manual

Note: Replacement accessories available through your exclusive Romstar distributor.

POWER REQUIREMENTS MONITOR REQUIREMENTS

+5 VDC 7 amp Horizontal Mount Raster Scan +12 VDC | amp Negative Composite Sync

Page 5

Recommended Tools and Supplies

ROMSTAR new game package. Phillips and Slot Screwdrivers Socket Set Enthusiastic Attitude Wire Cutters and Strippers Pliers or Channel Locks Planning and Careful Thought Electric Drill 3/32" © 1/4" © 7/16" Drill Bits 1/4” Plex Bit 1-3/16” Chassis or Sheet Metal Punch 1 1/4" Plex Hole Saw Glass of Water and a Snack Small File Razor Knife and Sharp Blades Straight Edge Patience Common Sense

Dip Switch Tables

Optimize Your Profits Painting Supplies (if you do your own painting) Paint Brush and Paint (don’t forget the primer) Paint Roller and Pan Sand Paper Putty Knife and Wood Putty A Good Night’ Sleep Staple Gun and Staples Soldering Iron and 60/40 Resin Core Solder Vacuum Cleaner Assorted Fastening Hardware Shrink Tubing: 3/32” ¢ 1/8” ¢ 3/16” Masking Tape 3 112" OR 4” Wire Ties Spray Window Cleaner and Rags (baby diapers work GREAT!)

Thorough Research shows that two and a half minute games both satisfy players and also keep the quarters flowing. If games aren’t running about two and a half minutes long, then collections probably aren't at their peak. You'll want to tailor your game to your location. The trick is to adjust a few DIP switches. (See the chart in this book.) It’s easy!

Page 6

Dip-Switch Bank Adjustment Options 1 1 Credit

1 Credit

Number Of Men 3

Screen Inversion off

on on Continue Play off off

U.S. — Use Either Coin 1 Or Coin 2 Recommended Settings

Dip-Switch Bank

Adjustment Upright — 1 Joystick Options

Upright — 2 Joysticks Table Bonus 20,000 — 50,000 off | off | off 20,000 — 60,000 on | off | off 20,000 — 70,000 off | on | off 30,000 — 60,000 on | on | off 30,000 — 70,000 on | off | on 30,000 — 80,000 off | on | on 40,000 — 100,000 off | on | on None on | on} on Starting Level First off | off | oft | Second on | off | off Third off | on | off Fourth Fifth

Sixth Seventh Recommended Settings

Page 7

—__Game Operation

TROJAN

+ Use Your Mastery Of Swordsmanship And The

Martial Arts To Rid The

World Of The Brutal King And His Evil Army. + Your Shield Is Positioned By Moving The Joystick While Pressing The Shield Button.

= Watch Out For The Magic Ball — If Hit, You Will

Lose Your Sword And Shield. (These May Be Regained By Striking The Flashing Shield). ~ Regain Power By Capturing The Winged Heart.

£ Strike “Open” Signs To Open Trap Doors.

GOOD FIGHTING

Page 8

Installation Procedures

Something To Think About Your final product will be anew game. You have made a wise decision to transform a game that has seen better days in the all important cash box into a new game. This is by far the most cost effective alternative to maximize the return of your initial investment. All you provide is the cabinet with a power supply and a monitor. Oh yes, you will need a touch of elbow grease. And that’s it! We provide the rest. The end result is ... anmew game at a very low cost. Fact: Spend a little time on the cabinet’s appearance (i.e. marquee, control panel and cabinet graphics). With a little paint, some wood putty and new lights, you will raise the profits of any game. . .especially with the introduction of anew game package. The new game look should always apply to the inside of your game as well as the outside. A few wire ties and shrink tubing on your harness; some fastening hardware on your subassemblies and a sweep with the ol’ vacuum cleaner will ensure that unnecessary glitches do not occur. Remember: You are creating anew game . If you have any questions or just need some advice on any of your new game transformations, don’t hesitate in giving a member of our technical staff a call.

Let’s Get Our Hands Dirty

Preparing the Original Game for the New Game

Remove the following:

1.Main logic board(s)4.Monitor Bezel
2.Control panel5.Marquee
3.Monitor plexiglass6.Graphics

| would recommend painting your cabinet to give it a ftesh new look. (if it is geographically inconvenient to make use of our facilities, you may consider having an auto body shop take care of your painting needs.) If your cabinet has wood grain sides; remove old graphics and adhesive (adhesive may be removed with lacquer thinner. If you intend to use your original plexiglass, be sure it is in mint condition or it should be replaced. Thoroughly clean out your cabinet.

Page 9

Time To Install Your New Goodies

Before You Start. ..Remember DO NOT Do This Work With The Power Onl!

Logic P.C.B. Cage Mount the logic cage securely (away from power supply). A Mark and drill pilot holes (3/32”). B Place the logic cage (bottom) over the holes and secure it with the supplied wood screws. C__ Install the PC.B. into the logic cage. Use feet and spacers supplied and adjust them so that the screws will go through the slots int he cage bottom.

Note: Leave the cage cover off until you have attached the entire wire harness and have tested the game for proper operation.

Wire Harness

Attach the wire harness connector to the main logic board. CAUTION: Sometimes the connector is not keyed and it is very easy to install it reversed on the logic board. Even if it is keyed, always triple check to be sure the wire inputs were connected correctly to the connector and the connector to the logic board.

Connecting the Wire Harness to the Existing Wires

When you hook up the control panel, power supply, monitor or other subassemblies that remain in the game cabinet to your new wire harness, try and use their existing secondary connectors.

  • Cut the original wire approximately three inches from the original connector. Strip off about one half inch of insulation.
  • Solder the new wire designated for that position to the original wire you just stripped.
Warning: DO NOT JUST TIE THE WIRES TOGETHER. THIS CAN CAUSE NAGGING INTERMITTENT PROBLEMS THROUGH LOOSE CONNECTIONS OR OXIDATION OR BOTH. Always take the time to do it right.
  • Melt shrink tubing around all your in-line wire connections. Do not use electrical tape. Tape could unravel over a period of time due to the cabinet heat and cause you a great deal of trouble.
  • Use wire tie wraps, and secure the cable to the cabinet whenever it seems necessary. Remember this is a new game , not a sloppy conversion.

Power Wires

  • Connect the wires that are designated for your power supply. You will need a supply of +5V, +12V & ground. Your new game package may not require all of the voltages that were used in the original game. Tie off any unused wires.
  • You will notice that you probably have more than one wire for each voltage. It is a good idea to use all wires supplied (double up if it is necessary). This will help to ensure that you don't overload the edge connector pins and cause them to “burn”.
Page 10

Monitor Wires

You will be connecting the wires designated for the RED, GREEN & BLUE video guns along with the SYNC & GROUND wires.

NOTE. . .CONCERNING SYNC: Your new game only calls for one sync wire connection, this is called composite sync (horizontal and vertical tied together). This composite sync is also negative. Most monitors have supply positions for both negative and positive sync. You can check your monitor manual or call our technical department for assistance.

Speaker Wires Find the two wires that are designated for the speaker and hook ‘em on up.

Coin Door Wires

Connect the designated wires to the coin switches and meter.

  • Youcanconnect your door lamps to the unused —5V power supply. Some games have separate power outputs for the coin door lamps.
  • Be sure to clean and lubricate your old coin mechanisms. Keep the money coming in.

GUESS WHAT?

You are almost done with the electrical connections of your new game. All you have left is the control panel wiring. But we are going to hold off on that for right now. We have a few other things we need to do first. So why don’t you go ahead and get yourself a drink of water and stretch your legs. When you return, we can take a fresh look at your progress and then move forward.

Smoke Test

What Test?

Don't worry. All this means is that you are ready to apply power to the system for the first time and you pray that there will be no smoke from a simple oversight. You are just about ready to power up the logic board. But first we need to recheck your work.

  • Carefully inspect the game for loose power wires, exposed connections and extra fastening hardware.
  • Make sure the logic board, board cage, monitor and power supply are securely fastened in place.
  • Double check the connectors to be sure they are wired and connected properly.
  • Set the dip switches on the logic board to the factory recommendations. (Refer to page 5.) Also, be sure you set the dip switches for ‘DEMO WITH SOUND”. This will enable you to hear as well as see that your new PCC.B. is functional.
Page 11

Time to Apply Power:

L. 2. Look and smell for smoke. (TURN OFF IMMEDIATELY IF ANY IS NOTICED) Listen for game sounds. If after one minute you have not heard any sounds A) Check for proper dip switch settings. B) Adjust volume control and check speaker connections. C) Check the +12V power supply to the logic board.

NOTE: If you do get sounds, but they are a little fuzzy, switch the wires around on the speaker. How is the monitor image? A) Is the picture in sync? If your picture has the top and bottom halves of the screen reversed and it will not stop rolling, change your sync polarity on the monitor. (Positive to negative}. If your monitor does not have dual polarity positions for sync, then you will need to reverse the sync yourself by installing a simple one I.C. circuit between the logic board and the monitor. (The following illustration shows a hookup for both composite and separate syncs

HORIZONTAL SYNC INPUT FROM P.C.B. {OR COMPOSITE SYNC INPUT) HORIZONTAL SYNC OUTPUT TO MONITOR: (OR COMPOSITE SYNC OUTPUT) VERTICAL SYNC INPUT FROM P.CB 5 Vcc

VERTICAL SYNC OUTPUT TO MONITOR

B) Now how's your picture? © It it centered? @ Is it too bright or dim? Is it in focus? Check your monitor manual for these adjustments. If your screen looks “off”, then your new game transformation may have been in vain. So let’s take the time to make the monitor look great. C) Is the picture upside-down? Dip switch 7 on switch bank “IA” should solve your problems.

Page 12

Control Panel Assembly

1.

2. Remove the buttons, joysticks and wire harness and put them aside fro now. Do not remove the original panel overlay until the new holes have been drilled. Mark positions on the panel for the new holes. ROMSTAR supplies a clear 1/8” thick piece of plexiglass with every new game package to cover the control panel. We feel that yournew game investment is well worth protecting. . .and the control panel is the first place to show wear and tear.

  • You will need to cut this piece to size. Use the control panel as a template. ¢ Use a razor knife to score the plexiglass deeply. Then use a pair of pliers to break away the extra plexiglass. Now drill the holes in your panel that you have marked off for the buttons, Joystick and bolts. Hint: For best results, use a chassis or sheet metal punch for button holes. Drill the same holes on your plexiglass panel protector. Once again use your panel as a template. Hint: To avoid chipping while you are drilling the holes, place the plexiglass securely on a soft wood surface and use a plexiglass drill bit and hole cutter. The holes are now all cut. Smooth them out on your panel and plexiglass with a fine toothed file. Remove the original graphics overlay from the panel. Clean up the panel and install your ROMSTAR graphics. Make It Easier: Peel the top half of the protective backing off of your graphics. Start from the center and smooth out your overlay. Make sure you have about an inch extra coming off the top. Vo bubbles please. Now peel off the bottom half and do the same as you did for the top. Adhere the instruction and function labels. Install the Plex Control Cover over your completed new game panel.
Note: Be sure to bolt the plexiglass securely to the panel. Mount the joystick and the buttons to the panel and wire them up. (Use the existing Panel wiring if possible)

Marquee Installation

Using the original marquee as a template, Center your mew game marquee graphics and score the new marquee deeply to fit the cabinet. Break off the excess with pliers. Be sure the light behind the marquee works. Everything should always work on anew game. Take your time ... Don’t forget this is going to be a new game.

Page 13

Side Graphic Installation

Be sure sides of game are clean and free of old adhesive, dust, etc.

  • Mark position of decal with eraseable pen or pencil (centered on upper half of cabinet). .
  • Peel off top 1/4 of decal backing and apply to cabinet with a smoothing motion (use a soft rag). Continue peeling off backing and smoothing.
  • Remove any small bubbles with a pin or razor blade (pop them!)

Finishing Touches

  • Check the game inside and out for any imperfections. Secure any loose wiring or fastening hardware.
  • Make sure the coin door is tight and the coin mechs are well adjusted. A game is NO good to anybody if you can’t get a coin into it.
  • Once again go over every step of this mew game transformation in your mind. Be sure everything is correct and to your liking.
  • Power up the game. A. Check all the coin switches. (Does the coin meter work?) B. Play your new game . ¢ Are all the player controls working?
  • Are the game sounds present?
  • Is the volume level proper? ¢ Are the dip switches set properly? Well, that’s about it. Good Luck.

n

Page 14

8 WAY JOYSTICK

SHIELD/KICK SWORD/PUNCH SHIELD/KICK SWORD/PUNCH

POSSIBLE 1 & 2 PLAYER LOCATIONS

Control Panel Positions

2 PCB Layout

Page 15

Trojan Edge Connector TYPE 1

Solder Side Parts Side

Ground Ground Black

Ground Black +5VDC Red +5VDC Red Video Red Red

Video Blue Blue T Video Ground Black

Key : IP Sword Brown IP Shield S| Red IP Up Orange IP Left

IP Down

IP Right Switch Ground

IP Select

Not Used

Coin |

Coin Ground

NOT USED

Not Used

Counter 1( +)

Counter I(-)

Speaker + +12VDC

12V Ground

Not Used

Ground =| Ground

+5VDC

+5VDC

Video Green

Video Sync Not Used

Key 2P Sword

2P Shield

2P Up 2p Down 2P Left

2P Right Switch Ground

2P Select

Not Used

Coin 2

Coin Ground

NOT USED

Not Used

Counter 2(+)

Counter 2(-)

Speaker - +12VDC

12V Ground

Not Used

Ground i

+ OLDMINIBIOPALWINI=][OlO}amIN| eH} aAlwIn|—

N co}

i]

N N

N w = N as

N w

N lox

N Ni a}P/AlO}olVYIN|~«|x]/E]<]/Cjalo| a} w]2/e]r-}aAle]Lia}m)olol;a]> N foo}

2P CONNECTIONS FOR COCKTAIL ONLY (Except 2P SELECT)

Page 16

Trojan Edge Connector TYPE 2

Solder Side Parts Side

Ground

Ground

+5VDC

+5VDC

Video Green

Video Sync Ground

Ground

+5VDC

+5VDC

Video Red

Video Blue

Video Ground Ol DON Qs; m| AlwWwi Nn; —

Orange 2P Shield Red 2P Sword

Green 2P Up Blue 2P Down Violet 2P Left Yellow 2P Right Black Ground Gray 2P Select IP Shield Orange IP Sword Red

IP Up Green IP Down Blue

IP Left Violet

IP Right Yellow Ground Black

IP Select

Coin 2 Coin 1

Counter 2 (+) Yellow Counter 2 (-) Brown Speaker (+) Gray +12VDC Yellow Ground Black Speaker - +12VDC

Ground alo}alaloals|N| ~<| x} |<} C} alo] a} a) 2) Se} er] Ale} r] alm) ol; o} a|>

Ground Ground Black

2P CONNECTIONS FOR COCKTAIL ONLY (EXCEPT 2P SELECT)