Solar Fox Parts and Operating Manual (Sept 1982)
Solar Fox (upright) (Bally Midway, 1981) · Parts & Operating Manual · 113 pages · 46 sections · original scan
September, 1982 Game Nos. 982, 578, 580
Bally/Midway’s
NO. 578 MINI
MIDWAY MFG.CO.
10750 W. Grand Avenue Franklin Park, Illinois 60131 No. 982 UPRIGHT U.S.A.
Phone: (312) 451-1360 Cable Address: MIDCO Telex No.: 72-1596
Form No. 0982-00300-0000
ELECTRICAL BULLETIN: FOR ALL APPARATUS COVERED BY THE CANADIAN STANDARDS ASSOCIATION (CSA) STANDARD C22.2 NO. 1, WHICH EMPLOYS A SUPPLY CORD TERMINATED WITH A POLARIZED 2-PRONG ATTACHMENT PLUG.
eat BLADES CAN BE FULLY INSERTED TO PREVENT BLADE
ATTENTION: POUR PREVENIR CHOCS ELECTRIQUES NE PAS UTILISER CETTE FICHE POLARISEE AVEC UN PROLONGATEUR. UNE PRISE DE COURANT OU UNE AUTRE SORTIE DE COURANT, SAUF SI! LES LAMES PEUVENT ETRE INSEREES A FOND SANS EN LAISSER AUCUNE PARTIE A DECOUVERT.
ally MIDWAY
OUR TOLL FREE NUMBERS FOR SERVICE INFORMATION CONCERNING THIS GAME, OR ANY OTHER BALLY/MIDWAY™ GAME YOU NOW HAVE ON LOCATION.
CALL US FOR PROMPT, COURTEOUS ANSWERS TO YOUR PROBLEMS
ANSWERS TO YOUR PROBLEMS.
Continental U.S. 800-323-7182 Illinois Only 1-800-942-0497
© COPYRIGHT MCMLXXXII BY BALLY/MIDWAY MFG. CO. ALL RIGHTS RESERVED. NO PART OF THIS PUBLICATION MAY BE REPRODUCED BY ANY MECHANICAL, PHOTOGRAPHIC, OR ELECTRONIC PROCESS, OR IN THE FORM OF A PHONOGRAPHIC RECORDING, NOR MAY IT BE TRANSMITTED, OR OTHERWISE COPIED FOR PUBLIC OR PRIVATE USE, WITHOUT PERMISSION FROM THE PUBLISHER. THIS MANUAL IS FOR SERVICE USE ONLY, AND NOT FOR GENERAL DISTRIBUTION. FOR PERMISSION REQUESTS, WRITE: MIDWAY MFG. CO., 10750 W. GRAND AVE., FRANKLIN PARK, IL 60131 Printed in U.S.A.
DESCRIPTION TABLE OF CONTENTS
{introduction ..
Location and Setup INSPeCtion 2.2... e ec eee een renee eee nent e tees Installation . Self-Test Game Volume Adjustment Control Option Settings
Game Operation Self-Test Mode. . Attract Mode.... Ready to Play Mode. Play Mode........ Two Piayer Operation
Maintenance and Repair Cleaning Fuse Replacement .. Opening the Control Panel ... Removal of the Main Display Glass & T.V. Bezel T.V. Monitor Replacement .......-. Printed Circuit Board Replacement Opening the Attraction Panel hee pber sOnbnA= o
Illustrated Parts Breakdown Transformer Board Assy. — Parts List .. Card Rack Assy. — Parts List........ No. 982 — Solar Fox Upright — Front No. 982 — Solar Fox Upright — Front — No. 982 — Solar Fox Upright — Rear Access........ No. 982 — Solar Fox Upright — Rear Access — Parts List 125 VA Filter Assy. — Parts List . 125 VA Filter Assy. No. 578 — Solar Fox ront . No. 578 — Solar Fox Mini — Front — Parts List No. 578 — Solar Fox Mini — Rear Access ....... No. 578 — Solar Fox Mini — Rear Access — Parts List. No, 580 — Solar Fox Cocktail — Front . No. 580 — Solar Fox Cocktail — Front — Parts No. 580 — Solar Fox Cocktail — interior Access ..... No. 580 — Solar Fox Cocktail — Interior Access — Parts List . Speaker Board Assy. — Upright — Parts List . Speaker Board Assy. — Upright. Control Assy. — Upright........ Contro! Assy. — Upright — Parts List Control Assy. — Mini & Cocktail Control Assy. — Mini & cocktail — Parts List . Front Door Assy. — U.S.A. 25¢. Front Door Assy. — U.S.A. 25¢ — Solar Fox — Ail Versions — Control Switch Assy. . Solar Fox — All Versions — Control! Switch Assy. — Parts List .. bYoHakoSDES *
7. pone tt thi ltitise NASCBVMDASGYAS Qeanaaaganangagnanggnaaanaaa ny o
TABLE OF CONTENTS (Continued) DESCRIPTION PAGE
VI. Technical Troubleshooting 6-1 Introduction .. 6-1 Generai Sugge: 6-1 Harness Component Troubleshooting 6-1 Transformer and Line Voltage Problems 6-2 A Glossary of Microprocessor Terms . 6-3 Introduction to the Z80 CPU......... 63 General Purpose Registers .... 6-4 Arithmetic and Logic Unit (ALU) . 6-4 Introduction Register and CPU Control 6-4 Z80 CPU Pin Description ..........- 6-4 MCR I System P.C. Board Jumper Options . 6-7
vil.
Vit. Coin Door Maintenance Metal Coin Acceptor Mechanisms . Plastic Coin Acceptor Mechanisms. x
D oa NN
T.V. Monitor Manual Introduction .. Symptom Diag Guide to Schematic Symbols Troubleshooting...... Theory of Operation. . Differences Between Monitors . Controls You May Not Touch Parts Interchangeability ....... Wells Gardner Monitor Schematic — 19' Wells Gardner Monitor Replacement Parts List Electrohome Monitor Schematic — 19".. Electrohome Monitor Replacement Parts Lis! Electrohome Monitor Schematic — 13"...... Electrohome Monitor Replacement Parts List .. © ay SOD DO Beatin ovowmabon+ OBRWOAO DErmnornnwns¢
Schematics & Wiring Diagrams Wiring Diagram — Upright. Wiring Diagram -- Mini. Wiring Diagram — C/T . 125 VA Power Supply (B Version) — Component Layout 125 VA Power Supply (B Version) — Schematic......... 125 VA Power Supply (C Version) — Component Layout 125 VA Power Supply (C Version) — Schematic ... Dual Power Amp P.C.B. — Component Layout. Dual Power Amp P.C.B. — Schematic C.P.U. Board — Component Layout C.P.U. Board — Schematic ........ Video Generator Board — Component Layout . Video Generator Board — Schematic............ Sound I/O Board (For G Version) — Component Layout . Sound |/O Board (For G Version) — Schematic........... Sound I/O Board (For K & L Version) — Component Layout Sound |/O Board (For K & L Version) — Schematic LevovovpooooDOOOO AAAS ALA NO oNOHRODA
NODROANAO
TABLE OF FIGURES
FIGURE PAGE
Assigned Point Values Location of Serial No., Interlock Switch, On/Off Switc! Major Sub-Assys. (Cont. from Fig. 2-1) . Interlock Switch Operation ... Location of Volume Control Option Switch Locations ..... Option Switch Settings ... Self-Test — Menue.. Self-Test — Sounds .. Self-Test — Player Inputs. Self-Test — Bookkeeping . Self-Test — Time Report . Self-Test — Score Report. Self-Test — Setup Options Self-Test — Channel Test. Self-Test — Preset .. Location of Hardware High Score/Initial Mode .. Rankings Display ... Location of Fuses... Opening the Control Panel — Upright & Mini. Opening the Cocktail Game ............. Removing the Control Panel — Cocktail Removing the Main Display Giass & T.V. Bezel ~ Upright Removing the Main Display Glass & T.V. Bezel — Min Removing the Top Glass & T.V. Bezel — Cocktail . . Removing the Monitor — Upright .. Removing the Monitor — Mini Opening the Cocktail Game .... Removing the Monitor — Cocktail . Removing P.C.B.s ... Removing P.C.B.s fro: Opening the Attraction Panel — Upright . Replacing Fluorescent Tube Starter .. Replacing Black Light............ Opening the Attraction Panel — Mini... Removing and Replacing the Coin Acceptor Cleaning the Metal Coin Acceptor ..... Lubricating the Metal Coin Acceptor . Opening the Plastic Coin Acceptor..... Changing the Plastic Coin Acceptor to Accept American or Canadian Quarters ... AdbODEEEHELELOOOOOOHARABONND Ded ieee) °F oo PHAADLARARWOHYHHEHOYOHOONYNNNN £ GhoOvmASAAAAL IA OONDHDAOMEAALOHOUSHEODDAGDHRODES NNOOA & NOaBRGDIO i WHNNPPRRPRRDARERRABRARERO OOOO EEEYESOENNN NNN honwnsttite WNT NEa ER ADA
Solar Fox
IMPORTANT NOTE
DO NOT plug in your new game yet. Before you do anything to your game, we recommend that you read SECTIONS | and || of this manual completely. It will not take more than a few minutes and it may be very helpful.
I. Introduction
SOLAR FOX is a one or a two player game. There are three models: the “UPRIGHT”, “MINI”, and “COCK- TAIL TABLE”. The Upright and Mini models have been designed for either RIGHT or LEFT hand use. When the two player mode is selected on the Upright or Mini model, the players take turns at the controls to take the Ship through the game course. If you have purchased the Cocktail Table model of this game, the rules of play are the same. The only difference is that in the two player mode of the Cocktail Table game, the picture flips to face you when it’s your turn. When playing this game, the Ship is under YOUR control. YOU make it move back and forth or up and down on the screen to eliminate the Fuzors, Pulzors, and to disable the Yellow Thrustors while building up your score. To disable all 4 Thrustors at once, you must either run over or shoot the Freezor as it works its way across the screen. These Fuzors are displayed in various patterns across the entire playing field of the screen. Each pattern is called a “rack”. The first rack is made up of Fuzors arranged in the shape of a large number “0”. The second and all future racks are made up of Fuzors arranged in evermore difficult patterns.
1-4 At random times during each rack, a special blinking Pulzor will appear for a short time. If you eliminate this special blinking Pulzor before it disappears, you earn BONUS POINTS. (The value of these bonus points is printed out on the screen as you eliminate the Pulzor.) ALL of the above must be accomplished while avoiding being hit by one of the many small Vortices shot at you by each of the four Thrustors. One of these Thrustors patrols EACH edge of the monitor screen: left, right, top, and bottom. This will really test your skill because you can have a lot of Vortices coming at you from four DIFFERENT directions at the SAME time. As your skill level increases and you work your way into the higher and higher racks: the Fuzors must be run over twice by your Ship before they are eliminated, their pattern is more varied, the number of Vortices shot at you is increased, the speed and distance the Vortices travel is increased, and the Thrustor’s aim gets better. Bonus Ships are awarded to you periodically throughout the game as you reach or pass certain preselected rack numbers. Each itemin the game that can be scored on hasan assigned point value as listed in Figure 1-1.
Major Features
There are several major features in your SOLAR FOX game: 1) The UPRIGHT and MINI models have been designed for ease of play by EITHER RIGHT HAND- ED or LEFT HANDED players; 2) You can select the level of difficulty at which you want to play (NOVICE or EXPERT); 3) You can vary the speed at which your Ship travels through the game course by pressing AND HOLDING DOWN the SPEED CONTROL Button; 4) Fuzor value increases by racks. See Figure 1 for details. 5) The game has OWNER/OPERATOR selected variable levels of difficulty so game play can be tailored to player skiil level in his area; 6) a bonus system which allows the player to skip a rack while receiving all the points for the “skipped” rack when the player successfully completes the current rack
Game Objective
The object of the game is to HAVE FUN while constantly increasing your skill as you play, running over and/or shooting as many scoreable objects as possible each time to get the highest score. BEFORE a time limit runs out; 7) There is a new and easy to use diagnostic package featuring: acomplete ROM/RAM check with bad chip location information read out on the monitor screen; the capability to check each of the game's 15 different sounds INDI- VIDUALLY; provision for checking each control and switch SEPARATELY; a full function Bookkeeping mode; an entire options list that can be set from the front console with NO NEED to crawl inside the back of the cabinet and look for tiny switches located on P.C. boards; a sound system test; and a “PRE-SET” category that can return ALL information in the Bookkeeping mode to zero and/or all operator selected options back to factory recommended settings; and 8) The game is equipped with a rechargeable battery so that it won't forget where it was the night before at closing — even if you turn it off. It will “remember” this information for up to two weeks.
DESCRIPTION POINTS AWARDED NOTES
VORTEX
ENERGY FIELDS
30 POINTS EACH
PULZOR 200 TO 800 POINTS EACH 300 POINTS EACH
100 POINTS EACH ONLY WHEN SHOT BY YOUR SHIP. NO POINTS ARE AWARDED IF YOU RUN INTO ONE WITH YOUR SHIP
INCREASES BY 10 POINTS EVERY 3 RACKS MAXIMUM VALUE 90 POINTS
CALLED OUT ON SCREEN AT TIME OF AWARD
100 POINTS EACH TIME 200 POINTS EACH TIME RED THRUSTOR YELLOW THRUSTOR
SKIPRACK TIMER BONUS POINTS
CHALLENGE RACK BONUS POINTS 100 POINTS FOR EACH SQUARE LEFT ON IT AT END OF RACK
1000 POINTS FOR CHALLENGE RACK NO. 1 “BEGINNING TIME” VARIES DEPENDING ON DIFFICULTY OF RACK PATTERN. THIS DOES NOT APPLY IN CHALLENGE RACK
INCREASES BY 600 POINTS FOR EACH ADDITIONAL CHAL- LENGE RACK CLEARED UNTIL YOU REACH NO. 12 @ 7,600 POINTS. THIS THEN REPEATS.
Figure 1-1 Assigned Point Values
II. Location and Setup
INSPECTION:
- Remove the game from its shipping crate.
- Inspect the entire outside of it for any signs of damage. O Any scratches?, dents?, cracks? QO Any broken controls? O Any broken glass or plastic? (1 Just look it over closely and make a note of any signs of damage.
- Remove the shipping cleats from the bottorn of the cabinet. 4, Install the four levelers, one at each corner of the cabinet. O Level the cabinet.
- Open the cabinet and inspect the inside of the game for any signs of damage. See Figure 2-1. D Also check to make sure ali plug-in connectors on the wire harness are firmly seated.
OD Replug any connectors found unplugged. DO NOT FORCE PLUGS ONTO CONNECTORS. DO NOT FORCE PLUGS TOGETHER. if it won't go on easily, assuming the keys are lined up, it either does not belong ihere or is damaged. D Make sure all printed circuit boards (P.C.B.’s) are firmly seated in their connectors. See Figure 2-1. These connectors are also keyed. The P.C.B.'s will only go into them one way without being damaged.
0 Note the location of the game's serial number. See Figure 2-1. O Check all major subassemblies to be sure they are mounted securely. These are called out in Figures 2-1 & 2-2. Power supply. Control panel(s). T.V. monitor. Other P.C.B.’s and/or P.C.B. rack, etc. Power supply filter assembly. Transformer board assembly.
- Make a note of any problems that can't be easily corrected,
- Call your distributor and/or service man about your problem list.
2-1 INSTALLATION:
- Location requirements: 0 Power: Domestic 110 V @ 60 Hz Foreign 200 V to 240 V @ 50 Hz © Temperature: 32° to 100°F (0° to 38°C) QO Humidity: Not over 95% relative O Space required: Upright 25" x 32" (63 x 81cm) Mini 20" x 24” (50 x 60cm) Cocktail 32" x 22” (81 x 55cm) O Game height: Upright 70" (175cm) Mini 61" (153cm) Cocktail 29" (73cm)
- Voltage Selection: Your game is designed to work properly on the line voltage where you are located. Check your line voltage with a meter to determine what its value is. Then check the power input wires to the main power supply transformer on your game to be sure they are connected to taps which correspond to your line voltage value. If the power input wires to the main power supply transformer are not connected to taps which correspond to your local line voltage, move them to the proper taps. If the line voltage in your area falls outside the upper or lower limits of the range of inputs covered by the main power supply transformer, DO NOT PLUG YOUR GAME IN until you have talked with your distributor and/or service man and obtained a solution to this problem. Otherwise you could damage your game.
- Interlock and power ON/OFF switches, See Figure 2-1. 0 To help prevent the possibility of getting an electric shock while working inside the game cabinet, interlock switches have been installed at each cabinet access door (this DOES NOT include the coin door in the Upright and Mini models). When any access door is opened, the interlock switch installed there turns off all power to the game. GB Check each interlock switch for proper operation. After checking the line voltage in your area and determining that the input wires to the main power supply transformer of your game are
| SERIAL | i | ere | | | SERIAL | oe | ON/OFF |
| NUMBER | jo | a | NUMBER | : |
TV. MONITOR
INTERLOCK
| INTERLOCK | e | switcH |
SWITCH
Loaic nets TV. BOARDS \ POWER SUPPLY MONITOR
| POWER SUPPLY [4 | - | PC.B. |
LoGiIc TRANSFORMER BOARDS
BOARD ASSY. (NOT SEEN)
| POWER SUPPLY | oS | ON/OFF | |||
| FILTER ASSY. | Cente: | SWITCH | POWER SUPPLY | ™ | ceanpaeey |
FILTER ASSY. UPRIGHT {NOT SEEN)
Tv. MONITOR
| SERIAL NUMBER | : | glia. | TRANSFORMER | ||
| (MAY BELOCATED | -.. | Hm | é | = | BOARD ASSY. |
| ON ANY CORNER) | : | : |
POWER SUPPLY
CONTROL PANEL (PLAYER 2)
CONTROL f PANEL :
| (PLAYER 1) | : | POWER SUPPLY |
| : | : | FILTER ASSY. |
| INTERLOCK | : | ON/OFF SWITCH |
SWITCH UNDER TABLE
| (INSIDE DOOR) | COCKTAIL | ON PLAYER 2 |
SIDE
Figure 2-1 Location of Serial No., Interlock Switch, On/Off Switch, & Major Sub-Assys.
2-2
iS a ee
UPRIGHT
Figure 2-2 Major Sub Assys. (cont. from Fig. 2-1)
connected properly —- or — after obtaining a solution to your over or under voltage problem from your distributor and/or your service man, plug the game into your A.C. wall outlet. The game ON/OFF switches for all models are located as shown in Figure 2-1. Turn the game on and allow it to warm up a few minutes. Slowly open each access door to the game (this does not include the coin door on the Upright and Mini models). As the door is opened approximately 1” (2.54cm) the power to the game should go off (the T.V. monitor, all the lights, and all sounds will stop). If this does not happen, check the interiock switch by this door to see if it has broken loose from its mounting or if it is stuck in the “ON” position. If the switch is found to be bad, turn the game off, unplug it, and replace the interlock switch. When done, plug the game back into the wall outlet, close the access door, and turn the game back on. After the game has warmed up, repeat the above interlock switch test. When the interlock switch is working properly and turns the power to the game off, power may be restored to the game with the access door(s) open. Take hold of the interlock switch plunger and gently pull it out to its fully extended position. THIS IS TO BE USED ONLY FOR SERVICING THE GAME. See Figure 2-3.
“NS
Figure 2-3 Interlock Switch Operation
SELF-TEST: Your new game will Self-Test itself to see if it has any bad parts. The information it receives while testing itself will be shown on the T.V. monitor. Some information can also be heard through the game’s speaker system. See the GAME OPERATION section for a more detailed description of this function. When there is a bad result according to the Self-Test, call your distriburor and/or service man to have the trouble fixed unless it is something you can do yourself (such as replace a bad RAM or ROM chip).
GAME VOLUME ADJUSTMENT CONTROL. See Figure 2-4. The game volume control pot is located just inside the cabinet on the right side of the coin door frame. There is only one pot. For adjustment, it may be reached through the coin door on ALL models. To make the sound louder, turn the pot clockwise as you face it (7 ). To make the sounds less loud, turn the pot counterclockwise as you face it ( # ).
OPTION SETTINGS: To change the most common option settings, youDO NOT have to take the game apart or go into the cabinet and hunt for tiny switches on P.C. boards. These most common options can be changed from the main console of the game while it is in the Self- Test mode. The Self-Test switch is located just inside the cabinet on the right side of the coin door frame as you face it. When changing any options, ALWAYS perform the Self-Test and play the game to be sure the ones selected are working properly. Of course, when you must change one of the switches that is located on one of the game's P.C. boards, it is also recommend- SERVICE CREDIT SWITCH
SELF-TEST SWITCH
VOLUME ADJUSTMENT
Figure 2-4 Location of Volume Control
ed that you perform the Self-Test and play the game to be sure the switches have worked properly and that no switches were accidentally moved that were not meant to be. (These switches are small and this can happen.) The P.C. Board option switch settings and what they will make the game do are shown in Figure 2-6. These switches are MAINLY INTENDED for use bya technician who is checking and/or performing tests on the game. See Figure 2-5 for option switch locations.
OPTION SWITCH sees, wall OPTION SWITCH 1
Figure 2-5 Option Switch Locations
SOLAR FOX
OPTION SWITCH SETTINGS
SWITCH NO. 1 — AT B 3 — LOCATED ON SOUND 1/0 P.C. BOARD
SW#1 SW#2 SW#3 SW#4 SW#5 SW#HE SW#7 SWH8 SW#9 SWH10 NO BONUS BASE AWARDED ON NOT NOT NOT NOT BONUS BASE AWARDED OFF** USED USED USED USED
BONUS BASE AWARDED AFTER EVERY 20th RACK COMPLETED
BONUS BASE AWARDED AFTER EVERY 10th RACK COMPLETED
SOUND PROVIDED IN ATTRACT MODE (LASTS ABOUT 1 MINUTE) NO SOUND PROVIDED IN
IGNORE HARDWARE FAILURE ONLY USED FOR DEVELOPMENT
HARDWARE FAILURE DETECTION
COCKTAIL TABLE UPRIGHT
FREEZE VIDEO NORMAL OPERATION
SWITCH NO. 3 — AT D 14 — LOCATED ON SOUND I/O P.C. BOARD
SWi#1 “SW#2*SW#3 *SW#4 NORMAL OPERATION SOUND I/O DIAGNOSTIC MODE
NORMAL OPERATION RAM/ROM TEST INDICATES TEST RESULTS VIA YELLOW LED ON SOUND 1/O BOARD: FAST FLASH = BAD ROM = BAD RAM
NORMAL OPERATION OSCILLATOR TEST
NORMAL OPERATION FILTER TEST
*NO EFFECT IF SW#1 OF SWITCH NO. 3 IS IN THE “OFF” POSITION. ** INDICATES FACTORY SETTINGS OF ABOVE SWITCHES.
Figure 2-6 Option Switch Settings
2-5
Il. Game Operation
SOLAR FOX is a one or a two player game with a color T.V. monitor. The game gives a display which has all the parts shown below.
RACK IDENTIFIER (RACK 12 SHOWN)
PLAYER 1 SCORE
REMAINING SHIPS
THRUSTOR The game has five possible modes of operation: ATTRACT, READY-TO-PLAY, PLAY, HIGH SCORE INITIAL, and SELF-TEST.
“SKIP-A-RACK-TIMER”
STATIONARY ENERGY FIELD
FUZORS
CREDITS REMAINING
Identification of “On Screen” Graphics During Play
SELF-TEST MODE
The Self-Test mode is a special mode for checking game play statistics as well as game switches and computer functions. It is the easiest and best way to check for proper operation of the entire game.
You may begin a Self-Test at any time by sliding the Self-Test switch to the “ON” position after the power to the game is on (the Self-Test switch is located just inside the cabinet on the right side of the coin door frame as you face it). When this is done, the game will react as follows:
- If the game is in the Attract mode when the Self- Test switch is moved to the “ON” position, it will finish the sequence and then go into the Self-Test mode. This is illustrated by the display of the Self- Test Mode Menue on the monitor screen.
If the game is in the Ready-To-Play mode or the Play mode when the Self-Test switch is slid to the “ON” position, it WILL NOT go into the Self-Test mode until AFTER the player's last ship has been destroyed (the game MUST be over). At this point, the game will go into the Self-Test mode. Again, this is illustrated by the display of the Self-Test Mode Menue on the monitor screen.
Figure 3-1 Self-Test — Menue
. The fastest way to enter the Self-Test mode is to slide the Self-Test switch to the “ON” position and then activate the “TILT” switch located on the back side of the coin door just below the lock mechanism. The game will then IMMEDIATELY go into the Self-Test mode.
The Self-Test mode has eight (8) major categories as illustrated by Figure 3-1.
- Itis easy to select what category you want to enter. By pushing the control stick forward or pulling it back, the Arrow (Cursor) at the left of the screen can be moved UP and DOWN, (forward= UP) and (backward = DOWN), until it is in front of the category you want to test. Release the control stick at this time. . After the Arrow has been positioned, depress either “SPEED CONTROL” Button on the console and the monitor screen will display the test category you have selected. Once you are IN one of the Self-Test mode categories, FOLLOW THE ON-SCREEN IN- STRUCTIONS TO COMPLETE THE TEST. . The next group of Figures (3-2 through 3-9) show the CORRECT screen presentation for EACH category of the Self-Test mode. During the SELF-DIAGNOSTICS section of the Self- Test mode, you will first see a cross hatch pattern on the screen for about 1/2 second. Second, you will see a lot of different colored bars shown on the monitor screen. These bars will be UNpainted one at a time from the top down. Third, you will see the screen painted Red, Blue, and Green in bars from the top down. Fourth, all the different colored bars you saw “Second” are displayed again. And fifth, the different colored bars are replaced by this message: “HIT SPEED CONTROL BUTTON TO EXIT”. Ifthe SPEED CONTROL Button is not hit, the test will repeat itself. This feature was designed into the game to enable over-night testing for an intermittent hardware problem. \f the SELF DIAGNOSTICS find one or more bad ROM or RAM chips: instead of going through what is described above, the game will give you a written message as to which parts are bad. This message includes their |.D.’s and their P.C. Board locations. During the SOUNDS section of the Self-Test mode, the game will give a display which looks like that shown in Figure 3-2.
POSITT OY 3 HIT FAST t BUTTON FOR
Figure 3-2 Self-Test — Sounds
O In this category, each of the game's 13 separate sounds can be checked individually in any order — or — you can tell the game to check them all in order — 3 through 17.
During the PLAYER INPUT section of the Self-Test mode, the game will give a display which looks like that shown in Figure 3-3.
ted, the Switch or Device activated is spelled out in the space indicated.
JOY STIUR.
AGTIUATE eR INPUT oe 8
Figure 3-3 Self-Test — Player Inputs CO In this category, each of the game’s player operated controls — including the coin switches on the back side of the coin door — may be checked individually. A game sound will be heard as each switch/control is actuated. If no game sound is heard, that switch/control is either not working, miswired, or disconnected. Check it out thoroughly. During the BOOKKEEPING section of the Self-Test mode, the game will give a display which looks like that shown in Figure 3-4.
-OURSGR BY USING r BUTTON FOR TEST
Figure 3-4 Self-Test — Bookkeeping C In this category a basic bookkeeping function is performed. And with the selection of the “TIME REPORT” and the “SCORE REPORT”, detailed breakdowns of game times and scores may be obtained. In the TIME REPORT and SCORE REPORT sections of the BOOKKEEPING mode, the game will give displays which look like those shown in Figure 3-5 and 3-6 respectively.
Figure 3-5 Self-Test — Time Report
SCORE REPORT
700 PTS
§ 000 PTS
10 000 P
20 000 PTS
30.000 PTS
f 40 O00 P'
- 000 PTS
80 000 PTS
190000 PTS
f 100 000 PTS eooccs ccs & LT
LT
tT
LT
L 7
ut
Ct i? LT
GT
HIT FAST BUTTON TO EXLT
Figure 3-6 Self-Test — Score Report
During the SETUP OPTIONS section of the Self-Test mode, the game will give a display which looks like that shown in Figure 3-7.
SETUP. OPTIONS.
#1 REPLAY LEVELS *9 TIMER LEVELS
STICK UP AND DOWN MOVES > BHT TL ARIBES HERON UALuES
PRESS FAST BUTTON TO EXIT
- = Factory recommended settings. Figure 3-7 Self-Test — Set Up Options
Ci In this category, all common game options may be changed from the control console: coins per credit, credits per base, bonus base(s) awarded at, difficulty level —, and so on.
DIFFICULTY LEVEL EXPLANATION:
The difficulty level of the game is controlled by the “TIMER LEVELS” setting in the SETUP OPTIONS section of the game. The easiest level of play is represented by “1” and the most difficult level of play is represented by “9”. An average setting of “3” is recommended. AWARD OF BONUS BASES EXPLANATION: Bonus Bases are awarded in two ways: 1) After having survived a certain number of racks (see OPTION SWITCH SETTINGS TABLE), and 2) By reaching or surpassing certain point values during game play. The point values that a player must attain during a game to receive additional ships is controlled by the “REPLAY LEVELS’ setting in the above table. Following is a chart which spells out exactly at what point values additional Ships will be awarded for each graduation in the “REPLAY LEVELS” setting. During the CHANNEL TEST section of the Self-Test mode, the game will give a display which looks like that shown in Figure 3-8. OGHANNEL OHANNEL 4 CHANNEL. CHANNEL CHANNEL OHANNEL CHANNEL oa fa we
HIT. FAST BUTTON TO EXIT
Figure 3-8 Self-Test — Channel Test
O In this category, the game conducts a test of its SOUND SYSTEM. Once you enter the CHANNEL TEST section of the Self-Test mode, the game automatically tests Channels 1 through 6 giving a tone for each one as it checks it. After the 6th Channel is tested, the game automatically repeats the test until the SPEED CON- TROL Button is hit. It then goes back to the Self-Test Mode Menue. During the PRESET section of the Self-Test mode, the game will give a display which looks like the following:
RESET VALUES MOVE ARROW TO SELECT RESET OPTIONS
1 ALL VALUES 2 COIN COUNTERS ONLY 3 FACTORY SETTINGS ONLY 4 EXIT
OSITION CURSOR BY USING
JOY STICK
HIT SPEED CONTROL BUTTON FOR TEST
Figure 3-9 Location of Hardware Master Reset Switches
During the GRID DISPLAY section of the Self-Test mode, the game shows a white cross haich pattern on the monitor screen. This is for alignment and/or test purposes. This pattern will remain on the monitor screen until the SPEED CONTROL Button is hit. The game will then go back to the Self-Test Mode Menue.
To leave the Self-Test mode, simply slide the Self-Test switch to the “OFF” position at ANY time. The game will then run through the ROM/RAM test display after which normal game functions will return to the monitor screen.
CROSS HATCH PATTERN:
Across hatch pattern is shown on thescreen when power is first turned on to the game, when the TILT. Switch is actuated, during the “SELF-DIAGNOS- TIC” portion of the Self-Test mode, and during the “GRID DISPLAY" portion of the Self-Test mode. This pattern may be kept on the screen for adjustment purposes as described earlier. When you are finished using the cross hatch pattern, simply hit the SPEED CONTROL Button to return to the Self-Test Mode Menue. HARDWARE MASTER RESET SWITCH: There are two of these little red switches, one on the Sound I/O Board and one on the CPU Board, located as shown in Figure 3-10. The function of each of these switches — when pressed — is to make the game THINK it has JUST. been turned on. They set up an “initial power-up” condition. We DO NOT recommend that you indiscriminately press EITHER of these switches. They should ONLY be used if there is a major problem encountered while testing the P.C. Boards.
HARDWARE MASTER RESET SWITCH
Figure 3-10 Location of Hardware Master Reset Switches
ATTRACT MODE
- The Attract mode starts: O Just after power has been turned on to the game. (Self-Test switch is in the “OFF” position.) O After a Self-Test has been completed and there are no more credits left in the game’s memory. O After a play has been finished, the score was not high enough to put the game into the High
4 00.10.90 Pp
4 B00 FC Gy 100. F
© 100 Porats € 200
# 00 ports
1% MYSTERY. VALUE
Attract Mode Display 1
ORILY HIGH SQORES
dal $a 2
EER
ZAG
ALL TIME HIGH. SCORE
DES 0
Attract Mode Display 3 Score/Initial mode, and there are no more credits left in the game’s memory. O After the High Score/Initial mode when there are no more credits left in its memory. 0 Jn the Attract mode, the game will give the following displays centered on the monitor screen:
POINTS soo00 POINTS 100000 POINTS 160000 POINTS
AND EVERY 10. RACKS
Attract Mode Display 2
Attract Mode Display 4
me hae a thn PL tolstabanlal
Gian joey Mere CO. Se eilaieeesenied 14 MIDWAY MPS CO. ALL RIGHTS RESERVEO
Attract Mode Display 5 Ready to Play Mode Display 2
1 No matter where the game isin the Attract mode sequence, it will immediately go to the following display as soon as a game has been paid for.
READY-TO-PLAY MODE
- The Ready-To-Play mode starts when enough coins have been accepted for a 1 or a 2 player game. It will hold this display on the monitor screen until a “1 PLAYER” or a “2 PLAYER” game has been selected BY MOVING THE CONTROL STICK FORWARD OR BACKWARD and the SPEED CONTROL Button pushed to begin the game — or — for about 60 seconds, whichever comes first. If no game selection is made before the 60 second time limit is up, a game will begin for the number of players the cursor was pointing at when the time limit expired.
- The Ready-To-Play mode ends when either a “1 PLAYER” or a “2 PLAYER” game has been selected and the SPEED CONTROL Button pushed to begin play.
- In the Ready-To-Play mode, the game will give the above display centered on the monitor screen.
- If the SPEED CONTROL Button is not pressed, a game will automatically begin as stated above when the 60 second time limit runs out.
Ready to Play Mode Display 1
3-7
PLAY MODE
- The Play mode begins when the SPEED CON- TROL Button is pressed. When this happens, the following is displayed centered on the monitor screen (NOVICE or EXPERT).
oe NOVICE
Play Mode Display
- The Play mode ends when your last Ship has been destroyed. When this happens, “GAME OVER” “PLAYER 1” is displayed centered on the monitor screen. . ON THE SCREEN: The game is made up of 20 racks of 20 different patterns and 12 Challenging racks of 12 different patterns. In the reguiar racks, the items on the screen are as follows: 4 Thrustors — one patrolling each edge — top, bottom, left, and right; your Space Ship; the pattern which is made up of Fuzors; and some stationary Energy Fields. (These vary in number according to the difficulty of the Fuzor pattern. The more difficult the pattern, the more stationary Energy Fields that wil! be mixed in with it. Some patterns have NO stationary Energy Fields at all.) At the beginning of each rack, the game tells which player is up and what each Fuzor’s point value is. When play starts, the Fuzor point value message disappears. The Skiprack Timer is also set at the beginning of each rack.
Also indicated in each rack is the rack number you're playing, the number of credits on the game, the number of players (1 or 2), and a running total of the player’s score(s).
3-8
- PLAY BEGINS: Your ship begins to move across the screen when play begins. At the same time: the Skiprack Timer begins counting and the four Thrustors begin patrolling their edges of the screen and shooting Vortices at you. Each thrustor has the capability of shooting two successive Vortices at you. So you could have a total of 8 moving Vortices to dodge at one time, coming at you from all different directions. The longer you are in any particular rack, the faster the Thrustors will fire at you. . PULZORS: At some time during each rack, a Pulzor will appear at a random iocation on the screen for a short period of time. If you run it over with your Ship, you will be awarded the bonus points for this Pulzor. If it should disappear BE- FORE you have the opportunity to run it over and/or shoot it, it WILL reappear again DURING this particular rack. The Pulzor’s bonus point value will vary between 200 and 800 points. Their bonus point value is displayed on the screen at the time they are run over or shot. . FREEZOR: At some point near the beginning of each rack, a Freezor will appear at one edge of the screen and begin to ERRATICALLY work its way to one of the other edges. If youcan run over or shoot the Freezor BEFORE it reaches the other edge of the screen, it will cause ALL FOUR (4) of the Thrustors to freeze in their tracks the instant you hit or run over the Freezor. The Thrustors will remain frozen in place for about 6 seconds. While in this condition, they cannot shoot Vortices at you or move in any other way at all. . SKIPRACK TIMER: The Skiprack Timer is set at the beginning of each rack. The more difficult the pattern of Fuzors that you have to eliminate, the longer the amount of time it will take the Skiprack Timer to count out. The object of the game is to completely eliminate the pattern of Fuzors from the screen before the Skiprack Timer reaches zero — “0”. Try to do this without loosing a Ship. However, if you should lose a Ship, this WILL NOT cancel the Skiprack Timer feature. When your new Ship appears, just pick up where you left off and try to eliminate the rest of the pattern of Fuzors BEFORE the Skiprack Timer counts out. if the Skiprack Timer counts out BEFORE you are able to eliminate the entire pattern of Fuzors, just continue playing and go on to the NEXT rack after you've eliminated the last fuzor in this one. You can then try to beat the Skiprack Timer in that next rack,
When you do beat the Skiprack Timer (eliminate all the Fuzors BEFORE it counts out), you are awarded 100 bonus points for every unused division stil! remaining on the Skiprack Timer, ie. 5
unused divisions left on the Skiprack Timer, 500 bonus points are added to your score. Plus, you get all the points for each Fuzor and the Pulzor that are in the next rack. The game then skips that rack and goes to the one after it for your next rack of play. If you beat the Skiprack Timer in that rack, the above events repeat themselves. If you do not beat the Skiprack Timer in that rack, just continue playing and you will advance to the next rack in line when your last Fuzor is eliminated in your present rack.
. SPEED CONTROL BUTTON: The SPEED CON- TROL Button is used to DOUBLE the speed at which your Ship travels on the screen when you are in the NOVICE mode of game play and to halve the speed at which your ship travels on the screen when you are in the EXPERT mode of game play. You WILL NOT be able to beat the Skiprack Timer unless you learn to control your Ship at the higher speeds.
THRUSTORS: These are interesting little fellows with a few surprises up their sleeves. They patrol the top, bottom, left, and right sides of the monitor screen shooting Vortices at you all the while. They can, however, be disabled for about 6 seconds ata time if you know how. Here's how. (You also get bonus points each time you disable a Thrustor.) For short periods of time during each rack, each Thrustor will turn yellow in color. When a Thrustor is yellow, it can be run over or shot by your Ship. When you do this, that Thrustor will remain stationary at the point where you hit or ran over it for approximately 6 seconds. During this time it will also stop shooting Vortices at you. If your ship touches a Thrustor when it is any color but yellow, your Ship will be destroyed. All four Thrustors may be disabled at the SAME TIME if you shoot or run over the Freezor as it works its way across the screen. All four Thrustors are also disabled for a short period of time if you shoot ANY single red Thrustor. However, they can still shoot Vortices at you, so BE CAREFUL! It is recommended that you ONLY approach a yellow Thrustor from the side to run it over. This is because they can still shoot Vortices while they are yellow — until you run them over. So, if you approach a yellow Thrustor from the front to run it over, the chances are very good to excellent that it will pop a Vortex right down your throat (very undesirable). Therefore, approach from the side. A Thrustor CANNOT shoot Vortices to the side — ONLY from its front. Thrustors can only shoot two Vortices each and cannot shoot again until one of the previously shot Vortices either disappears from the screen or goes off it at one edge. As you spend more time in any
3-9 particular rack, or, as you advance into the more difficult racks, the Thrustors will pick up the pace at which they shoot at you.
- VORTICES: There is only one type of Vortex in the game: that which is shot at you by the Thrustors. The moving Vortices are shot out by the Thrustors. As a general rule here, the easier the Fuzor pattern, the shorter the distance these moving Vortices will travel before they fade away and the slower will be the speed at which they travel this distance.
In the higher racks, the moving Vortices travel at high speed and go all the way across the screen no matter which direction they were shot from. If your Ship runs into any Vortex, it will be destroyed. STATIONARY ENERGY FIELDS: There is only one type of Energy Field in the game: that which is stationary. If your Ship should run into an Energy Field, it will be held and spun around several times before it is set free. This gives the Thrustors a chance to line up on you. The stationary Energy Fields are not present in all Fuzor patterns. As a general rule, the more difficult the pattern of Fuzors is, the higher the number of stationary Energy Fields that will be mixed in with it.
BONUS SHIPS: Bonus Ships are awarded in two different ways in the game: 1) When the player reaches or passes certain operator selected point values (see the “MACHINE SETUP” section of this manual for the individual point values at which each bonus Ship can be awarded), and 2) When the player reaches or passes a certain operator selected number of racks (see the “OPTION SWITCH SETTINGS TABLE”). FUZORS: Their point value increases as the rack numbers advance. The point value of the Fuzors is displayed at the top of the monitor screen BEFORE each rack begins. Example: for racks 1, 2 and 3, the Fuzors are worth 30 points each; for racks 4 and 5 the Fuzors are worth 40 points each; and so on.
As you get into the higher racks, the Fuzors have to be run over twice before they are eliminated. You are awarded their FULL value for EACH time you run them over. The way you can tell when you are in a rack where the Fuzors have to be run over twice before they are eliminated is that when you run over them once, their pattern changes drastically from those that have not been run over at all. If you decide to shoot some of the Fuzors (instead of running over them twice) they will be completely eliminated with ONLY ONE SHOT and you are awarded their entire point value times two. 11.
12.
13.
14.
15.
16. CHALLENGING RACKS: Every 4th rack is a Challenge Rack. There are ONLY Fuzors in a Challenge Rack. The Skiprack Timer is active in each Challenge Rack. It is used here as a countdown timer. You have a very short period of time to eliminate the pattern of Fuzors that makes up each Challenge Rack. You collect points for each Fuzor eliminated. If you eliminate the entire pattern of Fuzors BEFORE the timer runs out, you are awarded bonus points. You get 1,000 bonus points for completing the 1st Challenge Rack. This total increases by 600 points for each succeeding Challenge Rack until you get to the 12th one at 7,600 bonus points. The 12th Challenge Rack then repeats after every 3rd regular rack. It should be noted that ONLY Challenge Rack number 1 will come up after every 3rd rack unti! you beat the timer. Then, ONLY Challenge Rack number 2 will come up after every 3rd rack until you beat the timer for this pattern, and so on. When in any Challenge Rack, if you don’t beat the timer, all Challenge Rack action stops when the timer counts out and the next regular game rack is displayed on the screen. You retain all points for any Fuzors you eliminated up to the moment the timer counted out.
PLAY ENDS: When your last Ship is destroyed, “GAME OVER” “PLAYER 1” is displayed centered on the monitor screen.
HIGH SCORE/INITIAL MODE: If your score was high enough to become one of the ten best scores, the game will go into the High Score/ Initial mode immediately after the above display. lf your score was not high enough to cause the game to go into the High Score/Initial mode, it will either go to the Attract mode (if there are no more credits left in its memory) or into the Ready- To-Play mode (if there are still credits left in its memory). In the High Score/Initial mode the game gives a display which looks like that shown in Figure 3-11. By pulling the control stick toward you, you can make the cursor move down the alphabet: “A”, “B”, “C”, “D”, etc. By pushing the control stick away from you, youcan make the cursor move up the alphabet: “Z”, “Y”, “X”, “W”, etc. When you reach your initial, release the control stick and push the SPEED CONTROL Button. Your initial is printed out below the on-screen instructions. If you do not wish to put your initials Opposite your score, just press the SPEED CON- TROL Button three times. Three “A”’s will appear below the on-screen instructions.
\ ORILY HIGH SCORES dat Ba 8 jad Gad Sa 6
Sa? oa 6 qn 8 7AL0
ALL TINE HIGH SCORE
DES 0
Figure 3-12 Rankings Display
- Most of the above holds true in the “2 PLAYER” mode also. But there are a few minor differences.
TWO PLAYER OPERATION The Upright, Mini, and Cocktail Table models all have iwo player operation. In the two player mode, the rules of play are the same as in the single player mode. There are some additional rules, however.
- In the Upright and Mini models, the players must take turns at the controls.
- In the Cocktail Table model, each player has his own set of individual controls. The picture will flip to face you when itis your turn. (When itis not your turn, your set of controls will have NO effect on the game.)
- Your turn lasts until your Ship is destroyed. At this point, the game will do one of several things depending on whether or not the destroyed Ship was your last or if you still have others remaining in reserve.
DESTROYED SHIP — OTHERS REMAINING IN RESERVE O The game stops and “PLAYER UP” is displayed on the screen. O Next, the other player's Ship and Fuzor pattern appear on the monitor screen and game play begins for the other player. DESTROYED SHIP — NO OTHERS REMAINING IN RESERVE
O Game displays: “GAME OVER” “PLAYER___" on the monitor screen. D After the above display, if your score was high enough, it goes to the “HIGH SCORE/INITIAL” mode. After this mode, “PLAYER ___ UP”, the other player's Ship, and Fuzor pattern appear on the monitor screen. Play then begins for the other player. |f your score was NOT high enough to cause the game to go into the “HIGH SCORE/INITIAL” mode, the game will just display “PLAYER —___ UP”, the other player’s Ship, and Fuzor pattern on the monitor screen. Play then begins for the other player.
3-11
IV. Maintenance and Repair
Your NEW game needs certain types of maintenance to keep it in good working order. CLEAN, well MAINTAINED games attract players and EARN MORE PROFITS. The most important thing for you to remember is to run the Self-Test EVERY TIME you collect money from the coin box. JUST LOOKING at your game WILL NOT tell you if all its controls and inside parts are working correctly. The Self-Test will inform you whether or not your game is working the way it should. The second most important thing you should remember is to clean the outside of the game and coin acceptor mechanisms on a regular basis.
CLEANING The outside of the game cabinet plus the metal can be cleaned with any non-abrasive household cleaner. However, the front of the T.V. monitor tube and both sides of all other glass and plastic on or in the game MUST be cleaned with anti-static cleaner ONLY. For cleaning the coin acceptors: hot soapy water may be used on the plastic ones and any household cleanser may be used on the metal ones. If you wish, special coin machine cleaners that leave no residue may be purchased from your distributor. DO NOT dry-wipe any of the plastic panels. This is because any dust that was on them can scratch their surfaces. If this has happened, anyone looking through this type of damaged plastic. would feel he was looking at the game through a fog. This fogging damage CANNOT be repaired or reversed. The ONLY solution is to replace the damaged piece of plastic.
FUSE REPLACEMENT This game contains several fuses located as shown in Figure 4-1.
- UPRIGHT MODEL: As viewed from the back, facing the cabinet, with the rear access door removed; the fuses are located on the Mech. Panel and the Power Supply Board.
- MINI MODEL: As viewed from the back, facing the cabinet, with the rear access door removed; the fuses are located on the Mech. Panel and the Power Supply Board.
- COCKTAIL TABLE MODEL: As viewed from the coin door side of the cabinet, with the monitor tilted open to one side; the fuses are located on the Mech. Panel and the Power Supply Board. Replace fuses ONLY with the type and size listed in the Illustrated Parts Breakdown Section of this manual.
See the T.V. Monitor Manual (availabie on request from your distributor or the monitor manufacturer) and/or the T.V. Troubleshooting Section of this manual for information on these fuses.
FUSES LOCATED ON POWER SUPPLY BD. AND TRANSFORMER BOARD ASSY.
Figure 4-1 Location of Fuses
4a
OPENING THE CONTROL PANEL
- UPRIGHT MODEL: See Figure 4-2. O The control panet is held in place by two latches,
- MINI MODEL: See Figure 4-2. O The control panel is held in place by two latches,
Q one on the left side and one on the right side of the cabinet. They are spring loaded to provide constant positive pressure on their latch plates. They can be reached through the coin door AFTER turning power to the game off. To release the latches, lift up and toward the front center of the control panel. Once they are released, unhook them from their latch plates. To remove the control panel: Raise it up and tilt it toward you until youcan see the cable behind it. Cradling the control panel between yourself and the cabinet, disconnect it from its cabling. The control panel is now free and can be removed.
To reinstall the control panel, reverse this procedure.
UPRIGHT LATCHES one on the right side, and one on the left side of the cabinet. They are spring loaded to provide constant positive pressure on their latch plates. They can be reached through the coin door AFTER turning power to the game off. To release the latches, lift up and toward the center of the contro! panel. Once they are released, unhook them from their latch plates. To remove the control panel: Raise it up and tilt it toward you until you can see the cable behind it. Cradling the control panel between yourself and the cabinet, disconnect it from its cabling. The control panel is now free and can be removed. . To reinstall the control panel, reverse this procedure.
Figure 4-2 Opening the Control Panel — Upright & Mini
4-2
CLAMPS
Figure 4-3 Opening the Cocktail Game
- COCKTAIL TABLE MODEL:
O Each control panel is held in place by several screws, two on the inside of the cabinet and three along the outside bottom edge of the control panel. Turn power to the game off. Open the coin box door and release the two latches indicated in Figure 4-3.
Once they’re released, unhook them from their latch plates. Grasp the table top at “A” and open it as indicated in Figure 4-3.
Remove the screws which secure the control panel in place. See Figure 4-4. O To remove the control panel(s): Disconnect it from its cabling. The control panel is now free and can be removed.
O To reinstall the control panel, reverse this procedure. LIFT CONTROL UP
REMOVE
- SCREWS , EACH SIDE
REMOVE(3) SCREWS
Figure 4-4 Removing the Control Panel — Cocktail
REMOVAL OF THE MAIN-DISPLAY- O To reinstall the T.V. bezel assembly and the GLASS AND/OR THE main-display-glass, reverse this procedure. TV. BEZEL ASSEMBLY 1, UPRIGHT MODEL: 2. MINI MODEL:
DISPLAY GLASS
GLASS CLAMPING PLATE
DISPLAY GLASS
CLAMPING PLATE
Figure 4-5 Removing the Main Display Glass & T.V. Figure 4-6 Removing the Main Display Glass & T.V. Bezel — Upright Bezel — Mini
4-4
- COCKTAIL TABLE MODEL: See Figure 4-7.
O Remove the screws which secure the table top glass clamps in place. O Remove the table top glass. 0 Lift out the TV. bezel assembly. O To reinstall the T.V. bezel assembly and the table top glass, simply reverse this procedure.
Figure 4-7 Removing the Top Glass & T.V. Bezel — Cocktail T.V. MONITOR REPLACEMENT
- UPRIGHT MODEL: See Figure 4-8. O Turn power off to the game. O Open the rear access door. O Completely disconnect the T.V. monitor from all its cabling. DON'T FORGET THE CHASSIS GROUND WIRE. 0D Before removing the T.V. monitor, the maindisplay-glass must be removed. See above “Upright Model” procedure. O With the removal of only four bolts, the T.V. monitor will be loose.
OD The monitor mounting bars slide on top of and against two metal guides mounted to the cabinet’s right and left sides. The monitor is removed by sliding it out the back of the cabinet. See Figure 4-8. O To reinstall the T.V. monitor, procedure. D After replacing the T.V. monitor, be sure to run the game Self-Test.
. MINI MODEL: O Turn the power off to the game. O Open the rear access door. 0 Completely disconnect the T.V. monitor from all its cabling. DON'T FORGET THE CHASSIS GROUND WIRE. O Before removing the T.V. monitor, the maindisplay-glass and bezel must be removed. See above “Mini Model” procedure. reverse this
O With the removal of only four bolts, the T.V. monitor will be loose.
O The monitor is removed by supporting it and pulling straight back as shown in Figure 4-9. (BE CAREFUL not to hit monitor on its rear support bracket.) QO To reinstall the T.V. monitor, reverse this procedure. O After replacing the T.V. monitor, be sure to run the game Self-Test.
oo : ue
REMOVE (4) BOLTS
Figure 4-8 Removing the Monitor — Upright
- COCKTAIL TABLE MODEL:
O Turn the power off to the game. O Open the coin box door and release the two latches indicated in Figure 4-10.
O Once the latches are released, unhook them from their latch plates. O Grasp the table top at “A” and open it as indicated in Figure 4-10.
REMOVE (4) BOLTS
Figure 4-9 Removing the Monitor — Mini
CLAMPS
Figure 4-10 Opening the Cocktail Game
O Remove the screws which hold the table top glass clamps in place. O Remove the table top glass. 0 Lift out the T.V. bezel assembly. O Completely disconnect the T.V. monitor from all its cabling. DON'T FORGET THE CHASSIS GROUND WIRE.
O Remove the screws holding the T.V. monitor chassis to the “L” brackets by the door hinge(s). See Figure 4-11. O Close the Cocktail Table and re-laich it. 0 Remove the screws which secure the T.V. monitor mounting brackets to the edges of the slot cut in the table top. See Figure 4-11. OG Pry up the end of each monitor mounting bracket with a screwdriver or similar tool until you can grasp them both.
O Lift the T.V. monitor straight up and out of the table top being very careful not to bump the neck of the picture tube. O To reinstall the T.V. monitor assembly, reverse this procedure. O Be sure to check the clearance of the “L” brackets BEFORE setting the monitor into the table top. O After replacing the T.V. monitor, be sure to run the game Self-Test. REMOVE 6 SCREWS (G.FACH SIDE} LIFT MONITOR
STRAIGHT UP
REMOVE 4 SCREWS (2 EACH SIDE)
Figure 4-11 Removing the Monitor — Cocktail
PRINTED CIRCUIT BOARD (P.C.B.) REPLACMENT
- UPRIGHT MODEL: See Figure 4-12. O Turn the power to the game off. O To reinstall the above P.C.B.’s, reverse this procedure, O Unlock and open the rear access door. CO Disconnect all cabling from the P.C. boards and NOTE: P.C.B.’s are all keyed and will ONLY fit lift them out of their card rack. into their connectors one way without forcing . a them. The plugs on the cable harness which O Disconnect the linear power supply board from connect it to the P.C.B.'s are also keyed and will all its cabling, remove the P.C.B. supports indicated in Figure 4-12, and slide the linear power supply board out the back of the cabinet. ONLY go onto their connectors one way without forcing them.
REMOVE (2)
COCKTAIL
REMOVE REMOVE SUPPORT
UPRIGHT
Figure 4-12 Removing P.C.B.s
4-8
REMOVE SCREWS FROM SIDE OF CABINET TO REMOVE LOGIC BOARDS
Figure 4-13 Removing P.C.B.s from Card Rack
- MINI MODEL: See Figure 4-12. O Turn the power off to the game.
Unlock and open the rear access door. O Disconnect all cabling from the P.C. boards and lift them out of their card rack.
O Disconnect the linear power supply board from all its cabling, remove the P.C.B. supports indicated in Figure 4-12, and slide the linear power supply board out the back of the cabinet. O To reinstall the above P.C.B.’s, reverse this procedure.
- COCKTAIL TABLE MODEL: See Figure 4-12. O Turn the power off to the game.
O Open the cabinet: Open the coin box door and release the two latches indicated in Figure 4-10.
Once they're release, unhook them from their latch plates.
4-9 O Grasp the tabie top at “A” and open it as indicated in Figure 4-10.
O Remove the linear power supply board. See Figure 4-12. Disconnect it from all its cabling. Remove the two smallest P.C.B. supports. Once these are removed, the linear power supply can be lifted out the top of the cabinet. To reinstall the linear power supply board, reverse this procedure. O To remove the P.C. boards from the card rack. See Figure 4-13, Disconnect them from ALL their cabling. The P.C. boards are now free and can be slid from their rack. To reinstall the P.C. boards, procedure. reverse this
OPENING THE ATTRACTION PANEL
- UPRIGHT MODEL: o
Oo
o Turn the power to the game off. Opening the attraction panel: Remove the screws which secure the top bracket in place. (They are on its top side.) See Figure 4-14. Remove the top bracket and slide up the attraction panel. This exposes the speaker board assembly on which is mounted the speakers, the fluorescent and black light tubes, and their mounting bracket assemblies. See Figure 4-14. To reinstail the attraction panel, reverse this procedure. The fluorescent light tube may be replaced at this time. BE CAREFUL NOT TO DROP IT. reach all the necessary areas where cables MUST be disconnected. Disconnect the speaker board assembly from all its cabling. There is one plug at the upper right and upper left corners of the rear of the cabinet. There is also a small plug right at the ON/OFF switch. And DO NOT FORGET TO DISCONNECT THE GROUND WIRE LUG FROM THE ON/OFF SWITCH! Remove the screws which secure the speaker board assembly to the cabinet. The speaker board assembly is now free and can be slid out through the hole in the front of the game where the attraction panel was mounted. To reinstall the speaker board assembly, reverse this procedure. 0D Replacement of the fluorescent and ultraviolet tube mounting bracket assemblies. Disconnect it from its power cable. Remove the screws which secure them to the
a
o Replacing the fluorescent light tube starter. See Figure 4-15. Be sure the power to the game has been turned off. Grasp the starter (it is on the back of the mounting bracket), give it a quarter turn, and remove it from its socket. To replace the fluorescent light tube starter, reverse this procedure.
The ultraviolet light tube may be replaced at this time by removing the rear access door of the game and the back scenery panel if necessary. See Figure 4-16. BE CAREFUL NOT TO DROP IT. speaker board assembly. To reinstall the fluorescent ultraviolet tube mounting bracket assemblies, reverse this procedure.
REMOVE SCREWS AND LIFT ATTRACTION
O Replacing the ultraviolet light tube starter. See Figure 4-15. Be sure the power to the game has been turned off. Grasp the starter (it is on the back of the mounting bracket), give it a quarter turn, and remove it from its socket. To replace the ultraviolet light tube starter, reverse this procedure. O Removing the speaker board assembly: The attraction panel, the rear access door of the game, and, if necessary, the back scenery panel MUST be removed first. This will enable you to Figure 4-14 Opening the Attraction Panel — Upright
4-10
1/4 TURN TO REPLACE
FLUORESCENT
Figure 4-15 Replacing Fluorescent Tube Starter
O Replacing the speaker(s). Disconnect the speaker(s) from its cabling. Remove the nuts and bolts which secure the speaker in place and set them aside. Once they bolts which secure the speaker(s) in place are removed, the speaker(s) may be removed from the speaker board assembly. Reverse this procedure to reinstall the speaker(s). BLACK LIGHT CAN BE REACHED THROUGH HERE
- MINI MODEL. See Figure 4-17. O Turn the power off to the game.
O Remove the screws from the top and bottom of the formed attraction panel. O Remove the formed attraction panel by pulling it straight away from the cabinet. This exposes the attraction panel light bulbs and their mounting board.
O To service the light bulbs and their mounting board: Turn the power to the game back on so you can see which bulbs are burnt out. Mark the burnt out bulbs and turn the power to the game back off again. Figure 4-16 Replacing Black Light
4-11
To replace the burnt out bulbs, grasp them gently and pull straight out. The new bulbs are gently pushed into the empty sockets. To completely replace the fight bulb mounting board: Open the cabinet rear access door and unplug the mounting board from its power cable. Remove the screws that hold the mounting board to the cabinet. Gently slide the mounting board out the front of the cabinet being careful not to catch its cable on anything. - To reinstall the above removed items, reverse this procedure. REMOVE SCREWS ON TOP AND LIFT ATTRACTION PANEL UP
O To replace the speaker. Be sure the power is off to the game. Disconnect the speaker from its cabling. Remove the nuts and bolts securing the speaker. Slide the speaker out through the rear access door. To reinstall the speaker, simply reverse this procedure.
- THE COCKTAIL TABLE MODEL HAS NO BACK- LIT ATTRACTION PANEL. Figure 4-17 Opening the Attraction Panel — Mini

This page is a drawing, shown as the original scan.
SOLAR FOX — ALL VERSIONS — NOT SHOWN — PARTS LIST
ORDER BY PART NUMBER ONLY
(TEM PART NO. DESCRIPTION
TRANSFORMER BOARD ASSY. POWER TRANSFORMER — 115V., 60 HZ (UPRIGHT & MINI) TRANSFORMER (UPRIGHT & MINI) POWER TRANSFORMER — 110/125V., 60 HZ (COCKTAIL ONLY) TRANSFORMER W/MAGNETIC SHIELD (COCKTAIL ONLY) #8-32 x 3/4 CARRIAGE BOLT (4 REQ'D.) #8 FLAT WASHER (4 REQ'D.) #8-32 HEX NUT (4 REQ’D.) #8 x 11/16 UNSLOT. HEX HD. SCREW (22 REQ’D.) 1 POS. FUSE CLIP ASSY. (UPRIGHT & MINI) 2 POS. FUSE CLIP ASSY. ( MINI & COCKTAIL) 3 POS. FUSE CLIP ASSY. (UPRIGHT & COCKTAIL) SLO-BLO FUSE 1/2A., 250V. (UPRIGHT & COCKTAIL) SLO-BLO FUSE 2A., 250V. (UPRIGHT—2, MINI—2, COCKTAIL—3) SLO-BLO FUSE 2-1/2A., 250V. (ALL) 125VA. FILTER ASSY. 115V. CONVENIENCE OUTLET 2 LEAD TRANSFORMER BD, FILTER ASSY. CAPACITOR ASSY. — 60 HZ (UPRIGHT & COCKTAIL) CAPACITOR ASSY. — 60 HZ (MINI) CAPACITOR CLAMP MALE CONNECTOR — 5 TAB TERMINAL STRIP (COCKTAIL) TERMINAL STRIP (UPRIGHT & MIN!) 5.50 x .350 GROUND STRAP (UPRIGHT) 48.00 x .350 GROUND STRAP (UPRIGHT) 36.00 x .350 GROUND STRAP (COCKTAIL) 30.00 x .350 GROUND STRAP (MINI & COCKTAIL) GROUNDING CLIP MT00-00089-A000 MT00-00092-0000 MT00-00096-0000 MTO0-00093-0000 0017-00101-0628 0017-00104-0026 0017-00103-0008 0017-00101-0147 0720-00001-0100 0720-00001-0200 0720-00001-0300 0017-00003-0002 0017-00003-0004
0017-00003-0217 A945-00002-0000 A151-00079-0000 A508-00037-0000 A945~-00005-0000 A945-00005-0100 0017-00003-0379 0017-00021-6370 0017-00021-0624 3010-13106-0000 3000-17246-0500 3000-17246-0900 3000-17246-1000 3000-17246-1100 3010-03003-0000
CARD RACK W/BOARDS ASSY. CPU BOARD ASSYV. (UPRIGHT) CPU BOARD ASSY. (MINI & COCKTAIL) SOUND BOARD VIDEO GENERATOR BOARD (UPRIGHT) VIDEO GENERATOR BOARD (MINI & COCKTAIL) P.C. BOARD SPACER SUPPORT 1-1/8” LG. (4 REQ'D.) P.c. BOARD SPACER SUPPORT 5/8" LG. (4 REQ’D.) #6 x 5/16 SLT. HEX HD. SCREW (8 REQ'D.) BASE CARD RACK SUPPORT — BLOCK #8 x 1-1/4" SLT. HEX HD. SCREW (2 REQ'D.) #8 WASHER (2 REQ’D.) TOP CARD RACK SUPPORT — BLOCK SUPPORT BRKT. TO CABINET SIDE #6 x 1/2 SLT. HEX HD. SCREW (2 REQ'D.) A084-90009-A982 A084-90009-AS80 A084-90908-B982 A084-91399-A982 A084-91399-A580 0017-00042-0208 0017-00042-0287 0017-00101-0085 0968-0051 1-0000 0017-00101-0033 0017-00104-0031 0968-005 10-0000 0968-00125-0000 0017-00101-0014
5-1
NO. 982 — SOLAR FOX — UPRIGHT — FRONT
ane cy vee oe ee
5-2
NO. 982 — SOLAR FOX — UPRIGHT — FRONT — PARTS LIST
ORDER BY PART NUMBER ONLY
PART NO.
0982-00900-00XF 0537-00903-0061 0508-00104-0000 0982-00101-00XF 0017-00101-0138 0017-00009-0522 A982-00025-0000 A982-00022-0000 A982-00023-0000 0982-00902-00XF 0982-00905-00XF 0537-00903-0017 A982-00020-0000 0982-00904-0000 0550-00101-0100 0550-00101-0200 0555-00901 -0000 0961-00115-00XF 0017-00009-0033 A982-00031-0000 0017-00042-0301 0017-00042-0304 0017-00032-0093 0017-00103-0054 A090-00300-11BK 0090-00002-04BK 0017-00101-0121
0935-00906-0100 0017-00102-0048 0017-00103-0026
0982-00106-00XF 0017-00101-0138 DESCRIPTION
DISPLAY HEADER GLASS CHANNEL 5-5/16 LG. (2 REQ'D.) HEADER RETAINER BRKT. — UPPER RETAINER/GRILLE #8 x 5/8 TORX TAMPER RESISTANT SCREW (15 REQ'D.} LONG ARM KEY T-20 (FOR ABOVE SCREW) SPEAKER BOARD ASSY. A.C. ADAPTOR CABLE ASSY. “SPEAKER CABLE ASSY. MIRROR MAIN VIEWING GLASS GLASS CHANNEL 18-3/4 LG. (2 REQ'D.) CONTROL SHELF PLATE ASSY. CONTROL SHELF OVERLAY CONTROL SHELF MTG. BRKT. — RIGHT CONTROL SHELF MTG. BRKT. — LEFT PLASTIC LOCATING PIN (8 REQ’D.) STRIKE (2 REQ’D.) LATCH (2 REQ’D.) CONTROL GRIP ASSY. YELLOW PUSH BUTTON ASSY. (2 REQ’D.) RED PUSH BUTTON ASSY. (2 REQ'D.) PUSH BUTTON SWITCH W/HOLDER (4 REQ’D.) 5/8-11 PAL NUT (4 REQ’D.) U.S.A. 25¢ COIN DOOR ASSY. LARGE COIN DOOR FRAME #6-32 x 5/16 PHIL. TRS. HD. SCREW (3 REQ’D.) (MOUNTS COIN DOOR TO FRAME) KICK PLATE 3/8-16 x 2” LEG LEVELER (4 REQ'D.) 3/8-16 LEG LEVELER NUTS (4 REQ’D.)
GLASS CLAMPING PLATE #8 x 5/8 TORX TAMPER RESISTANT SCREW (3 REQ’D.)
5-3
NO. 982 - SOLAR FOX — UPRIGHT — REAR ACCESS
etka oe : a dbencovuspetes
r eine We peyian sone a oe
5-4
NO. 982 -- SOLAR FOX — UPRIGHT — REAR ACCESS — PARTS LIST
ORDER BY PART NUMBER ONLY
PART NO. DESCRIPTION
A088-00013-0000 0894-00916-0000 0982-00906-0000 0982-00902-00XF 0982-00903-00XF A088-00015-0000 0017-00003-0339 ON/OFF SWITCH AND BRKT. ASSY. PLASTIC PULL AND VENT (2 REQ’D.) MONITOR MASK MIRROR REAR SCENERY INTERLOCK SWITCH AND BRKT. ASSY. ELECTROHOME — 19” COLOR DUAL SYNC. HORIZ. MTG. MONITOR (OR) WELLS GARDNER — 19” COLOR DUAL SYNC. HORIZ. MTG. MONITOR MONITOR MTG. CHANNEL ASSY. (2 REQ'’D.) MONITOR RAIL (2 REQ'D.) 1/4-20 x 3/4 UNSLOT HEX HD. BOLT (4 REQ’D.) 1/4-20 x 1/2 SLOT HEX HD. BOLT (4 REQ'D.) 7/8" DISH WASHER (8 REQ’D.) #8 x 11/16 UNSLOT HEX HD. SCREW (8 REQ’D.) 7/8" FLAT WASHER (8 REQ’D.) MONITOR SHIELD (FISH PAPER) CARD RACK W/BOARDS ASSY. SOUND BOARD ASSY. CPU BOARD ASSY. VIDEO GENERATOR BOARD ASSVY. SUPPORT BRKT. ASSY, — TOP CARD SUPPORT BASE — BOTTOM DUAL POWER AMP P.C. ASSY. 125VA. POWER SUPPLY P.C. ASSY. P.C. SUPPORT BRKT. 12” (2 REQ’D.) P.C. SUPPORT BRKT. 6-1/2" (2 REQ'’D.) TRANSFORMER BOARD ASSY. LINE CORD ASSY. CASTER ASSY. (2 REQ'’D.) WHEEL BRKT. (2 REQ'D.) PLASTIC WHEEL (2 REQ'D.) SHAFT (2 REQ’D.) 3/8 E-RING (2 REQ'’D.) 0017-00003-0439
A508-00005-0000 0595-00104-0000 0017-00102-0066 0017-00102-0002 0017-00104-0014 0017-00101-0141 0017-00104-0046 0982-00907-0000 A982-00007-0000 A084-90908-B982 A084-90009-A982 A084-91399-A982 A968-00018-0000 0968-0051 1-0000 A082-90910-E000 A082-90412-D000 0624-00902-0100 0624-00902-0500 A982-00009-0000 A508-00023-0000 A961-00007-0000 0961-00109-0000 0017-00042-0255 0894-00702-00XF 0017-00100-0037
ADDITIONAL PARTS LIST
MULTIFUNCTION SWITCH & BRKT. ASSY. BACK DOOR LOCK ASSY. 5-5/8 SQR. BACK DOOR VENT GRILLE (4 REQ'D.) COIN BOX CRADLE ASSY. COIN BOX COVER COIN BOX HANDLE COIN DEFLECTOR (2 REQ’D.) LARGE PLASTIC CASH BOX 1/4-20 x 1-3/8 RND. HD. BOLT (4 REQ'D.) 7/8 DISH WASHER (4 REQ'D.) 1/4-20 HEX NUT (4 REQ'D.) A515-00021-0000 A097-00009-0000 0017-00009-0490 A950-00006-0000 0950-00105-0000 0950-00104-0000 0950-00101-0000 0950-00900-0000 0017-00101-0142 0017-00104-0014 0017-00103-0018
NO. 982 — SOLAR FOX — UPRIGHT — REAR ACCESS — PARTS LIST (Continued)
ORDER BY PART NUMBER ONLY
ITEM PART NO. DESCRIPTION
A968-00029-0000 VIDEO SIGNAL CABLE ASSY. A982-00012-0000 MASTER CABLE ASSY. A089-00006-0000 125VA. FILTER CABLE ASSY. #1 A089-00007-0000 125VA. FILTER CABLE ASSY. #2 A982-00010-0000 HIGH VOLTAGE CABLE ASSY. A982-00011-0000 LOW VOLTAGE CABLE ASSY. A982-00015-0000 COIN DOOR CABLE ASSY. A982-00016-0000 CONTROL SHELF CABLE ASSY.
FILTER ASSY. — PARTS LIST ORDER BY PART NUMBER ONLY
PART NO. DESCRIPTION
0945-00101-00XF CHASSIS 0945-00803-0100 CAPACITOR — 55000MF — 25V. 0945-00803-0200 CAPACITOR — 100000MF — 15V. 0945-00100-0000 CAPACITOR STRAP 0017-00101-0555 #6-32 x 5/16 SLT. HEX HD. SCR. (4 REQ’D.) 0017-00021-0539 5 POSITION TERMINAL STRIP (2 REQ’D.) 0017-00101-0510 #4-40 x 1/2 SLT. PAN HD. SCR. (4 REQ’D.) 0017-00104-0087 #4 FLAT WASHER (4 REQ'D.) 0017-00104-0071 #4 EXT. TOOTH WASHER (4 REQ'D.) 0017-00103-0002 #4-40 HEX NUT (4 REQ’D.) 0062-122H7-1XXX RESISTOR — 150 OHM, 2W. 0062-086H7-1XXX RESISTOR — 47 OHM, 2W. — LOCATED ON OPPOSITE TERMINAL STRIP 0017-00003-0008 FUSE — 6 AMP — 120V. 0017-00003-0174 FUSE — 10 AMP — 32V. 0017-00003-0433 FUSE HOLDER (2 REQ’D.) 0017-00041-0008 RUBBER GROMMET A089-00007-0000 FILTER CABLE ASSV. #2 A089-00006-0000 FILTER CABLE ASSY. #1 0945-00804-0100 DIODE — 12A. — 50V. (4 REQ'D.) 0017-00103-0086 #10-32 HEX NUT (4 REQ’D.) 0017-00021-0484 SOLDER LUG (4 REQ’D.) 0017-00104-0107 #10 FLAT WASHER (4 REQ’D.) 0017-00009-0510 INSULATOR (8 REQ’D.) 0017-00042-0283 BUSHING (4 REQ'D.) 0945-00900-0000 DIODE FORMED FISHPAPER COVER — NOT SHOWN
5-6
FILTER ASSY.
5-7
NO. 578 — SOLAR FOX — MINI — FRONT
EG: se oa
ie oe a s
5-8
NO. 578 — SOLAR FOX — MINI — FRONT -- PARTS LIST ORDER BY PART NUMBER ONLY ITEM PART NO. DESCRIPTION 0578-00901-00XF | HEADER DISPLAY PLEXI 0537-00903-0060 | GLASS CHANNEL 4-1/2" LG. (2 REQ’D.) 0574-00100-00XF | | HEADER RETAINING BRKT. (2 REQ’D.) 0017-00101-0138 | #8 x 5/8” TORX TAMPER RESISTANT SCREW (6 REQ’D.) 0017-00009-0522 LONG ARM KEY T-20 (FOR ABOVE SCREW) A574-00007-0000 | __ INSERT DISPLAY ASSY. 0017-00003-0219 | #194 LAMP 14V., .27A. (5 REQ’D.) 0017-00031-0030 | | WEDGE BASE LAMP SOCKET (5 REQ’D.) A574-00015-0000 | INSERT CABLE ASSY. 0017-00009-0393 | BLACK SPEAKER GRILLE W/SLOTS (2 REQ’D.) 0017-00003-0430 | 6" x 9" SPEAKER 4 OHM, 10W. (2 REQ’D.) 0578-00900-00XF | VIEWING GLASS 0537-00903-0056 | GLASS CHANNEL 14-1/2” LG. (2 REQ’D.) A578-00019-0000 | | GLASS CLAMPING PLATE ASSY. 0017-00101-0138 | #8 x 5/8" TORX TAMPER RESISTANT SCREW (2 REQ’D.) A514-00004-0000} —_—T.V. BEZEL ASSV. 0513-00900-0000 BEZEL 0934-00905-0000 | PLEXI-GLASS (TINTED) A961-00026-0000} | BEZEL MTG. BRKT. ASSY. (2 REQ’D.) A578-00016-0000 | OVERLAY/CONTROL PLATE ASSY. 578-00017-0000 ] | CONTROL SHELF PLATE 0578-00902-0000 } | CONTROL SHELF OVERLAY 0550-00101-0100 } | CONTROL SHELF MTG. BRKT. — RIGHT 0550-00101-0200 } CONTROL SHELF MTG. BRKT. — LEFT 0555-00901-0000 PLASTIC LOCATING PIN (4 REQ’D.) 0961-00115-00XF} STRIKE (2 REQ’D.) 0017-00009-0033 LATCH CLAMP (2 REQ’D.) A578-00022-0000} | CONTROL ASSY. 0017-00042-0301 YELLOW PUSHBUTTON ASSY. (2 REQ’D.) 0017-00042-0304 RED PUSHBUTTON ASSY. (2 REQ'D.) 0017-00032-0093 PUSHBUTTON SWITCH W/HOLDER (4 REQ’D.) 0017-00103-0054 | 5/8-11 PAL NUT (4 REQ’D.) A090-00300-11Bk] —_U.S.A. 25¢ COIN DOOR ASSY. 0090-00002-048K] | LARGE COIN DOOR FRAME 0017-00101-0121 #6-32 x 5/16 PHIL. TRS. HD. SCREW (3 REQ’D.) (MOUNTS COIN DOOR TO FRAME) 0935-00906-0400 KICK PLATE 0017-00102-0048 | 3/8-16 x 2” LEG LEVELERS (4 REQ’D.) 0017-00103-0026 | _3/8-16 LEG LEVELER NUTS (4 REQ’D.)
5-10 NO. 578 — SOLAR FOX — MINI — REAR ACCESS
NO. 578 — SOLAR FOX — MINI — REAR ACCESS — PARTS LIST
PART NO. ORDER BY PART NUMBER ONLY
DESCRIPTION
0017-00003-0430 0017-00003-0340
0017-00003-0435
A926-00012-G0XF 0513-00101-0000 0017-00102-0066 0017-00104-0014 A088-00015-0000 A950-00004-0000 A950-00006-0000 0950-00105-0000 0950-00104-0000 0950-00101-0000 0950-00900-0000 0017-00101-0142 0017-00104-0014 0017-00103-0018 A082-90412-D000 0624-00902-0100 0624-00902-0500 A082-90910-E000 A580-00013-0000 A084-90009-0580 A084-90908-B982 A084-91399-A580 A968-00018-0000 0968-00511-0000 A568-00009-0000 A945-00002-0000 A088-00013-0000 A508-00023-0000
A097-00009-0000 0017-00009-0490 0926-00904-0000 A578-00010-0000 A578-00011-0000 A578-00012-0000 A968-00029-0000 A982-00015-0000 A578-00013-0000 A089-00006-0000 A089-00007-0000 0555-00901 -0000 A515-00021-0000 3010-03003-0000 6" x 9" SPEAKER 4 OHM, 10W. (2 REQ’D.) ELECTROHOME — 13” COLOR DUAL SYNC. HORIZ. MTG. MONITOR (OR) WELLS GARDNER — 13” COLOR DUAL SYNC. HORIZ. MTG. MONITOR T.V. MONITOR BRKT. ASSY. MONITOR MTG. BRKT. 1/4-20 x 3/4 UNSLOT HEX HD. BOLT (4 REQ'D.) 7/8 DISH WASHER INTERLOCK SWITCH & BRKT. ASSY. COIN BOX ASSY. COIN BOX CRADLE ASSY. COIN BOX COVER COIN BOX HANDLE COIN DEFLECTOR (2 REQ’D.) LARGE PLASTIC CASH BOX 1/4-20 x 1-3/8 RND. HD. BOLT (4 REQ'D.) 7/8 DISH WASHER (4 REQ’D.) 1/4-20 HEX NUT (4 REQ'D.) 125VA. POWER SUPPLY P.C. BD. ASSY. P.C. SUPPORT BRKT. 12” LG. (2 REQ'D.) P.C. SUPPORT BRKT. 6-1/2” LG. (2 REQ'D.) DUAL POWER AMP P.C. ASSY. CARD RACK W/BOARDS ASSY. CPU BD. ASSY. SOUND BBD. ASSY. VIDEO GENERATOR BD. ASSY. SUPPORT BRKT. ASSY. — TOP CARD SUPPORT BASE — BOTTOM TRANSFORMER BOARD ASSY. 125VA. FILTER ASSY. ON/OFF SWITCH & BRKT. ASSY. LINE CORD ASSY.
ADDITIONAL PARTS LIST
BACK DOOR LOCK ASSY. 5-5/8" SQR. BACK DOOR VENT GRILLE (4 REQ’D.) PROTECTIVE BUBBLE — BACK DOOR HIGH VOLTAGE CABLE ASSY. LOW VOLTAGE CABLE ASSY. MASTER CABLE ASSY. VIDEO SIGNAL CABLE ASSY., COIN DOOR CABLE ASSY. CONTROL SHELF CABLE ASSY. FILTER CABLE ASSY. #1 FILTER CABLE ASSY. #2 PLASTIC LOCATING PIN (6 REQ'D.) MULTIFUNCTION SWITCH BRKT. ASSY. GROUNDING CLIP
NO. 580 — SOLAR FOX — COCKTAIL — FRONT
5-12
NO. 580 — SOLAR FOX — COCKTAIL — FRONT — PARTS LIST
PART NO. ORDER BY PART NUMBER ONLY
DESCRIPTION
0017-00009-0499 0580-00901-0000 0775-00104-00XF 0017-00101-0117 0557-00900-0000 0508-00905-0000 A580-00004-0100 A580-00004-0200 0017-00009-0393 0017-00009-0482 0017-00003-0431 0017-00101-0136 0017-00103-0061 A090-00300-11BK 0090-00002-02BK 0017-00101-0121
0017-00102-0048 0017-00103-0026 COVER GLASS — 32” x 22" x 1/4” ARTWORK UNDERLAY GLASS CLIPS (8 REQ’D.) #8 x 5/8 PHIL. TRS. HD. SCREW (16 REQ’D.) TV. BEZEL SMOKED PLEXI — 17-3/8" x 13-1/4" x 1/8” CONTROL SHELF ASSY. — PLAYER 1 CONTROL SHELF ASSY. — PLAYER 2 BLACK SPEAKER GRILLE W/SLOTS (2 REQ'’D.) SPEAKER GRILLE — SMALL (2 REQ’D.) 4" SQR. SPEAKER — 4 OHM, 10W. (2 REQ’D.) #8-32 x 1-1/4 CARRIAGE BOLT (16 REQ'D.) #8-32 HEX NUT W/SEMS (16 REQ’D.) U.S.A. 25¢ COIN DOOR LARGE COIN DOOR FRAME #6-32 x 5/16 PHIL. TRS. HD. SCREW (3 REQ'D,) (MOUNTS COIN DOOR TO FRAME) 3/8-16 x 2" LEG LEVELERS (4 REQ’D.) 3/8-16 LEG LEVELER NUTS (4 REQ'’D.)
5-13
NO. 580 - SOLAR FOX — COCKTAIL — INTERIOR ACCESS
@ © ® OF: OF
Of
©
NO. 580 — SOLAR FOX — COCKTAIL — INTERIOR ACCESS — PARTS LIST
ORDER BY PART NUMBER ONLY
PART NO. DESCRIPTION
ELECTROHOME — 19” COLOR DUAL SYNC. HORIZ. MTG. MONITOR (OR) WELLS GARDNER — 19” COLOR DUAL SYNC. HORIZ. MTG. MONITOR MONITOR SUPPORT ASSY. — LEFT MONITOR SUPPORT ASSY. — RIGHT #8 x 5/16 UNSLOT. HEX HD. BOLT (6 REQ’D.) SUPPORT ANGLE (2 REQ’D.) #8-32 x 5/16 SLT. HEX HD. SCREW (4 REQ’D.) 2-1/2" HINGE (2 REQ’D.) #8-32 x 1-1/4" CARRIAGE BOLT (4 REQ'D.) #8-32 x 3/4” CARRIAGE BOLT (4 REQ’D.) #8-32 HEX NUT W/SEMS (8 REQ’D.) DECORATIVE OVERLAY — PLAYER 1 DECORATIVE OVERLAY — PLAYER 2 CONTROL PANEL (2 REQ’D.) #8-32 x 1/2 CARRIAGE BOLT (8 REQ’D.) #8-32 HEX NUT W/SEMS (8 REQ’D.) #6 x 1/4 PHIL. TRS. HD. SCREW (10 REQ’D.) BOTTOM PAN (2 REQ’D.) CONTROL ASSY. (2 REQ’D.) YELLOW PUSH BUTTON ASSY. (2 REQ’D.) RED PUSH BUTTON ASSY. (2 REQ'D.) PUSH BUTTON SWITCH W/HOLDER (4 REQ’D.) 5/8-11 PAL NUT (4 REQ’D.) CONTROL PANEL LOCATING BRKT. (4 REQ’D.) #8 x 1/2" SLT. HEX HD. SCREW (16 REQ’D.) LIGHT SHIELD (2 REQ’D.) WEDGE BASE LAMP SOCKET (4 REQ’D.) #194 LAMP 14V., .27A (4 REQ’D.) #6-32 x 5/16” SLT, HEX HD. SCREW (4 REQ’D.) 125VA. POWER SUPPLY P.C. ASSY. P.C. SUPPORT BRKT. 6-1/2" LG. (4 REQ’D.) TRANSFORMER BOARD ASSY. CARD RACK W/BOARDS ASSY. CPU BOARD ASSY. SOUND BOARD ASSY. VIDEO GENERATOR P.C. ASSY. SUPPORT BRKT, ASSY. — TOP CARD SUPPORT BASE — BOTTOM 125VA. FILTER ASSY. FAN ASSEMBLY 4” FAN FAN PLATE VENT SCREEN #6-32 x 1/2” R.H.M.S. (4 REQ'D.) #6 EXT. WASHER (4 REQ’D.) #6-32 HEX NUT (4 REQ'D.) #8 x 5/8 SLT. HEX HD. SCREW (4 REQ’D.) 0017-00003-0339
0017-00003-0439
2 A515-00019-0000 3 A515-00019-0100 0017-00101-0109 4 0927-00101-00XF 0017-00101-0598 5 0017-00009-0514 0017-00101-0639 0017-00101-0628 0017-00103-0061 0580-00900-0100 0580-00900-0200 0580-00100-00XF 0017-00101-0620 0017-00103-0061 0017-00101-0341 8 0510-00101-00XF 9 A580-00015-0000 10 0017-00042-0301 1 0017-00042-0304 0017-00032-0093 0017-00103-0054 12 0930-00104-0000 0017-00101 -0025 13 0727-00901-0000 14 0017-00031 -0044 0017-00003-0219 0017-00101-0555 15 A082-90412-D000 0624-00902-0500 16 A580-00007-0000 17 A580-00013-0000 A084-90009-A580 A084-90908-B982 A084-91399-A580 A968-00018-0000 0968-0051 1-0000 18 A945-00002-0000 19 A775-00013-0000 0151-00081-0000 0775-001 10-00XF 0749-00106-00XF 0017-00101-0347 0017-00104-0009 0017-00103-0005 0017-00101-0026 NO
5-15
NO. 580 — SOLAR FOX — COCKTAIL — INTERIOR ACCESS — PARTS LIST (Continued)
PART NO.
ITEM
COVOTGHKRON=A A082-90910-E000 A088-00014-0000 A515-00021-0000 A088-00013-0000 0610-00132-00ZN 0017-00009-0033 0017-00101-0141 A927-00019-0000 A962-00004-0000 A962-00005-0000 0962-00101-0000 0017-00101-0628 0017-00104-0022 0017-00103-0061 A580-00010-0000 A580-00008-0000 A580-00009-0000 A580-00005-0100 A580-00005-0200 A580-00011-0000 A982-00015-0000 A927-00005-0000
A508-00023-0000 ORDER BY PART NUMBER ONLY
DESCRIPTION
ADDITIONAL PARTS LIST
DUAL POWER AMP P.C. ASSY. INTERLOCK SWITCH & BRKT. ASSY. MULTIFUNCTION SWITCH BRKT. ASSY. ON/OFF SWITCH & BRKT. ASSY. STRIKE (2 REQ’D.) LATCH CLAMP (2 REQ'D.) #8 x 11/16 UNSLOT HEX HD. SCREW (8 REQ'D.) COIN BOX ASSY. COIN BOX COVER ASSY. COIN BOX SIDE CHANNEL ASSYV. -- SHORT COIN BOX SIDE CHANNEL — SHORT #8-32 x 3/4 CARRIAGE BOLT (4 REQ’D.) #8 WASHER (4 REQ’D.) #8-32 HEX NUT W/SEMS (4 REQ’D.) MASTER CABLE ASSY. HIGH VOLTAGE CABLE ASSY. LOW VOLTAGE CABLE ASSY. CONTROL SHELF CABLE ASSY. — PLAYER 1 CONTROL SHELF CABLE ASSY. — PLAYER 2 VIDEO SIGNAL CABLE ASSY. COIN DOOR CABLE ASSV. LEG KIT ASSY. (HIGH BASE) — OPTIONAL (INCLUDES 4 LEGS & HARDWARE) LINE CORD ASSY.
SOLAR FOX — UPRIGHT — SPEAKER BOARD ASSY. — PARTS LIST
PART NO.
0017-00003-0043 0017-00003-0095 0017-00003-0445 0017-00031-0036 0017-00101-0573 0595-00105-0000 0017-00003-0026 0017-00101-0598 0017-00003-0019 0017-00003-0412 A961-00042-0000 0017-00003-0430 0017-00101-0141
A982-00022-0000 A982-00023-0000 A508-000 17-0000 A508-00027-0000 ORDER BY PART NUMBER ONLY
DESCRIPTION
18" FLUORESCENT LAMP — COOL WHITE 18” BLACK LIGHT FLUORESCENT LOCKS (4 REQ'D.) FLUORESCENT SOCKET (4 REQ'D.) #6-32 x 1/2 SLT. RND. HD. SCREW (8 REQ'D.) FLUORESCENT BRKT. (2 REQ'D.} BALLAST (2 REQ’D.) #8-32 x 5/16 SLT. HEX HD. SCREW (8 REQ’D.) STARTER (2 REQ'D.) STARTER HOLDER (2 REQ'’D.) LINE FILTER ASSY. (2 REQ’D.) 6" x 9” SPEAKER 4 OHM, 10W (2 REQ’D.) #8 x 11/16 UNSLOT. HEX HD. SCREW (8 REQ'D.)
A.C. ADAPTOR CABLE ASSY. SPEAKER CABLE ASSY. FLUORESCENT CABLE ASSY. FLUORESCENT CABLE ASSY. — BLACK LIGHT
SOLAR FOX — UPRIGHT — SPEAKER BOARD ASSY.
5-17
SOLAR FOX — UPRIGHT — CONTROL GRIP ASSY.
5-18
SOLAR FOX — UPRIGHT — CONTROL GRIP ASSY. — PARTS LIST
ORDER BY PART NUMBER ONLY
[ rem | PART NO. DESCRIPTION
0873-00900-0200 CONTROL GRIP — LEFT 0873-009800-0100 CONTROL GRIP — RIGHT 0873-00902-0000 LENS 0628-00906-0000 TRIGGER A628-00028-0000 CONTROL GRIP SWITCH ASSY. 0020-00202-0000 SWITCH PLATE 0017-00101-0528 #5-40 x 3/4 SLT. RND. HD. M.S. (2 REQ’D.) 0873-00123-00XF SWITCH MTG. BRKT. 0017-00101-0083 #4-20 x 3/8 PHIL PAN HD. SCREW (2 REQ’D.) 0017-00101-0116 #10-32 x 3/8 HEX BUTTON HD. SCREW (5 REQ'D.) 0017-00009-0513 1/8" TAMPER PROOF ALLEN KEY 0628-00904-0000 SLIDE 0628-00921-0000 SLEEVE A628-00024-0000 TUBING & PIVOT PIN PINNING ASSY. 0017-00101-0615 #8-32 x 3/8 SLT. PAN HD. M.S. (4 REQ’D.) A982-00029-0000 CENTERING BRKT. WELD ASSY. 0628-00909-0000 BUMPER 0873-00113-00XF BUMPER MTG. BRKT. 0982-00908-0000 GROMMET — MODIFIED 0017-00101-0799 #10-32 x 3/8 SLT. HEX HD. SCREW (4 REQ'D.) 0017-00103-0081 #10-32 HEX NUT W/SEMS (4 REQ'D.) 0628-00922-0000 SHOULDER WASHER 0017-00104-0014 DISH WASHER 0628-00700-00XF ACTUATING PIN A628-0003 1-0000 STOP PLATE & SWITCH BRKT. ASSY. 0017-00101-0598 #8-32 x 5/16 SLT. HEX HD. SCREW (4 REQ'D.) 0628-00920-0000 ROLLER 0921 -00700-0000 ACTUATOR 0017-00100-0025 1/4" E-RING
5-19
5-20 SOLAR FOX — CONTROL ASSEMBLY — COCKTAIL & MINI
SOLAR FOX — CONTROL ASSEMBLY — COCKTAIL & MINI PARTS LIST
ORDER BY PART NUMBER ONLY
PART NO.
A727-00020-0000 0010-00267-0000 0017-00032-0103 0017-00101-0148 0727-00703-00XF 0017-00100-0025 0578-00903-0000 0921 -00902-0000 A595-00006-0000 0017-00101-0637 0017-00103-0061 0727-00700-00XF |. 0727-00907-0000 0017-00101-0598 0962-00904-0000 0017-00101-0527 0020-00202-0000 A932-00009-0000 A932-00012-00XF 0017-00021-0634 0017-00101-0107 0932-00905-0000 0921-00700-0000 0727-00704-0000 DESCRIPTION
KNOB & SWITCH ASSY. COMPRESSION SPRING SWITCH #8-32 x 1/4 TAMPER RESISTANT TORX SCREW (2 REQ'D.) SHAFT 1/4” E-RING SLEEVE SLIDE PLATE PIVOT PLATE WELD ASSY. #8-32 x 1” CARRIAGE BOLT (4 REQ’D.) #8-32 HEX NUT W/SEMS (4 REQ'D.) ADAPTOR GROMMET #8-32 x 5/16 SLT. HEX HD. SCREW (10 REQ’D.) SLEEVE #5-40 x 5/8 SLT. RND. HD. SCR. (8 REQ’D.) SWITCH PLATE (4 REQ'D.) SWITCH ASSEMBLY (4 REQ’D.) STOP PLATE & SWITCH BRKT. ASSY. 2 POSITION TERMINAL STRIP #6 x 5/16 SLT. HEX HD. SCREW WEAR PLATE ACTUATOR END GROMMET
5-21
FRONT DOOR ASSEMBLY — U.S.A. 25¢
FRONT DOOR ASSEMBLY — U.S.A. 25¢
ORDER BY PART NUMBER ONLY
PART NO. DESCRIPTION
0090-00002-02BK DOUBLE ENTRY COIN DOOR FRAME 0017-00101-0121 #6-32 x 5/16 PHIL. TRS. HD. SCR. (3 REQ'D.) A090-00073-0°BK DOUBLE ENTRY COIN DOOR W/DRESS PLATE 0017-00101-07423 #8 x 1/4 UNSLOT. HEX HD. SCREW (4 REQ'D.) 0017-00067-0019 KEY HOOK 0017-00101-0552 #8-32 x 1/4 CARRIAGE BOLT (4 REQ’D.) 0090-0011 7-03XF COIN ENTRY PLATE -— 25¢ (2 REQ'D.) A097-00005-0000 DOOR LOCK & KEY W/SCREW & NUT (OR) A097-00006-0000 DOOR LOCK & KEY W/SCREW & NUT 0090-00128-00XF DOOR TILT SWiTCH BRKT. 0017-00005-0041 DOOR CAM A090-00096-0000 DOOR TILT SWITCH 0090-00126-01XF SWITCH BACK-UP PLATE 0017-00101-0525 #5-40 x 9/16" PHIL. HD. M.S. (2 REQ'D.) A090-00096-0000 DOOR TILT SWITCH & BRKT. ASSY. (ITEMS 9 & 11 THRU 13) 0090-00903-9500 25¢ WINDOW (2 REQ'D.) . 0090-00143-00XF COIN PLEX RETAINER 0017-00003-0219 12 VOLT LAMP — G.E. #194 (2 REQ'D.) 0017-00031-0048 WEDGE SOCKET W/BRKT. (2 REQ'D.)
- 0017-00103-0084 #6-32 HEX NUT W/SEMS (4 REQ'D.) A090-00089-0000 COIN METER W/DIODE 0017-00101-0124 #6 x 1/4 UNSLOT. HEX HD. SCR. (8 REQ’D.) 0017-00032-0051 PUSH BUTTON SWITCH 0017-00032-0007 SLIDE SWITCH 0017-00072-0034 STEEL OVAL HD. RIVET 0090-00173-0000 COIN COUNTER MTG. BRKT. A090-00082-0100 TEST SWITCH & BRKT. ASSY. (ITEMS 23 THRU 25) A090-00087-0000 COIN CHUTE & TOP ASSYV. (2 REQ’D.) 0010-00134-0000 SPRING 0010-00181-0000 SPRING 0017-00007-0083 1/8 x 1-5/8 ROLL PIN 0090-00129-00XF PIVOT POST 0090-00167-00XF PIVOT LEVER 0093-00155-O0XF REJECT LEVER 0017-00100-0018 E-RING A090-00088-0000 REJECT LEVER ASSV. (2 REQ'D.) (ITEMS 30 THRU 33) A090-00085-0000 COIN ACCEPTOR FRAME ASSYV. (2 REQ’D.) 0017-00005-0003 COIN ACCEPTOR W/STRING CUTTER (2 REQ'’D.) (OR) 0017-00005-0211 COIN ACCEPTOR W/ANTI STRING DEVICE (2 REQ'D.) (OR) 0017-00005-0214 COIN ACCEPTOR W/STRING CUTTER (2 REQ’D.) A090-00064-0000 ANTI-PENNY DEVICE 0017-00101-0099 #6 x 1/4 SLT. HEX HD. M.S. (2 REQ'D.) 0090-00162-00XF COIN SWITCH MTG. BRKT. 0017-00005-0203 COIN SWITCH CHUTE 0017-00005-0195 COIN SWITCH 0010-00599-0000 COIN SWITCH WIRE 0017-00007-0132 PUSH-ON RING A090-00059-0400 COIN SWITCH & WIRE ASSY. (ITEMS 40 THRU 42) 0017-00101-0698 #4-40 x 3/4 SLT. RND. HD. M.S. (2 REQ’D.) A090-00077-0000 COIN GUIDE & SWITCH ASSY. (ITEMS 38 THRU 43)
5-23
SOLAR FOX — ALL VERSIONS — CONTROL SWITCH ASSY.
SOLAR FOX — ALL VERSIONS — CONTROL SWITCH ASSY. — PARTS LIST
ITEM PART NO.
A628-00031-0000 0932-00905-0000 0017-00101-0598 A932-00009-0000 0020-00202-0000 0017-00101-0527 ORDER BY PART NUMBER ONLY
DESCRIPTION
STOP PLATE & SWITCH BRKT. WEAR PLATE #8-32 x 5/16 SLT. HEX. HD. SCREW (2 REQ'D.) SWITCH ASSY. (4 REQ'D.) SWITCH PLATE (4 REQ'D.) #5-40 x 5/8 SLT. RND. HD. M.S. (8 REQ'D.)
TRAVEL OF PART NO. 0921-00700-0000 ACTUATOR IS APPROX. 1/8”. SWITCH BLADE ASSY. SHOULD BE ADJUSTED TO MAKE CONTACT AT 1/16" OF ACTUAL TRAVEL. TYPICAL 4 SWITCHES.
_--— 0017-00 101-0527
- 0020-00202-0000
092 1-00700-0000 A932-00009-0000
5-25
VI Technical Troubleshooting
Introduction
The most common problems occur in harness components such as the coin acceptor, player controls, interconnecting wiring, etc. The TV monitor and PCB computer cause their share of problems too, but not as much as the harness and its component parts. TV monitor troubleshooting will not be covered here because it is covered in that section of this manual. As you already know, the PCB computer is a complex device with a number of different circuits. Some circuits remain basically the same among games, but overall there are a great many differences between them. PCB troubleshooting procedures, therefore, can be lengthy and will differ greatly among games. However, some basic Z-80 CPU information is involved in this section.
General Suggestions
The first step in any troubleshooting procedure is correctly identifying the malfunction’s symptoms. This includes not only the citcuits or features malfunctioning, but also those still operational. A carefully trained eye will pick up other clues as well. For instance, a game in which the computer functions fail completely just after money was collected may have a quarter shorting the PCB traces. Often, an experienced troubleshooter will be able to spot the cause of the problem even before opening the cabinet. After all the clues are carefully considered, the possible malfunctioning areas can be narrowed down to one or two good suspects. Those areas can be examined by a process of elimination until the cause of the malfunction is discovered.
Harness Component Troubleshooting
Typical problems falling in this category are coin and credit problems, power problems and failure of individual features. NO GAME CREDIT For example, your prospective player inserts his quarter and is not awarded a game. The first item to check is if the quarter is returned. If the quarter is returned, the malfunction most certainly lies in the coin acceptor itself. First, use a set of test coins (both old and new) to ascertain that the player's coin is not undersize or underweight. If your test coins are also returned, coin acceptor servicing is indicated. Generally, the cause of this particular problem is a maladjusted magnet gate. Normaily, this will mean slightly closing the magnet gate a little by turning the adjusting screw out a bit (see section on coin acceptor for more details). If the quarter is not returned and there is no game credit, the cause of the malfunction may be in one of several areas. First try operating the coin return button; if the coin is returned, the problem is most likely in the magnet gate. Enlarge the gap according to the coin acceptor service procedures. If this does not cure the problem, remove the coin acceptor, clean it and perform the major adjustment procedure. {f the trapped coin is not returned when the wiper lever is actuated, you may have an acceptor jammed by a slug, gummed up with beer, a jammed coin chute, or mechanical failure of the acceptor mechanism. In this case, first check for the slug that will generally be trapped against the magnet. If so, simply remove the slug and test the acceptor. If the chute is blocked, remove the acceptor and remove the jammed coins. If there is actual failure of the acceptor, remove the unit and repair as indicated in the coin acceptor service procedures. If the coin is making its way through the acceptor (that is, falling into the coin box), yet there is still no game credit, you either have a mechanical failure of the coin switch or electrical failure of the coin and credit circuits. The first place to begin is by checking the coin switch. Most of these switches are the make/break variety of micro switch, which is checked by testing for continuity between the NO, NC, and C terminals. When not actuated, the NC and C terminals should be continuous and the NO terminal open. When operated, the NO and C terminals should close and the NC should be open. If the coin switch checks out, examine the connections to the terminals to make sure there is good contact. If necessary, use the continuity tester and check from the terminal lug on the switch to the associated PCB trace. This will tell you if there is a continuous line all the way to the credit circuit.
If the coin switch wires do not check out, the problem is in the computer — mostlikely in the coin and credit circuitry. ff you do get game credit when a coin is deposited, but the game will not start when the start switch is pressed, you may have a problem in the start switch, the interconnecting wiring or in the computer. First check the switch. If the switch is OK, proceed to check the wiring. Again, make sure you go from the terminal lug on the switch to the PCB trace. This way, you will check the terminal contact as well as PCB edge connector contact. if the wiring is continuous, proceed to check the PCB credit circuit. If not, check each section of the wiring, until the discontinuity is located. If the wiring is OK, the problem must lie in the computer.
Transformer and Line Voltage Problems
Your machine must have the correct line voltage to operate properly. If the line voltage drops too low, a circuit in the computer will disable game credit. The point at which the computer will fail to work will vary
some from game to game, but no game’ will work on
line voltage that drops below 105 VAC. Low line voltage may have many causes. Line voltage normally fluctuates a certain amount during the day as the total usage varies. Peak usage times occur mainly at dawn or dusk, so if your machine's malfunction seems to be related to the time of day, this. may be a factor. A large load connected to the same line as the game (such as a large air conditioner or other device with an exceptionally large motor) may drop the line voltage significantly when starting up. This drop can result in an intermittent credit problem. In addition, poor connections in the location wiring, plug, or line cord may also cause a significant drop in power. Cold solder joints in the game's harness, especially in areas like the transformer connections, interlock switch, or fuse block, may also produce the same results, although probably on a more permanent basis. Sometimes location owners (especially in bars) replace light switches with dimmer rheostats, and the game is sometimes on the same line. Obviously, the voltage available to the game is going to drop dramatically when the dimmer is turned. In any case, the way to check for correct line voltage is with your VOM. Set the VOM to 250 VAC and stick the probes in the wall receptacle. If it’s OK here, check the transformer primary connections. If you do not get 117 VAC, examine the solder joints on the transformer, fuse block, and interlock switch. If you do get 117 VAG, the problem must be either in the transformer, harness connections, or in the PCB power supply.
6-2 If you suspect the transformer, check its secondaries with the VOM set to 50 VAC and correlate the readings with the legend on the side of the transformer. The transformer must also be correctly grounded, so check the ground potential as well, especially if there is ahum bar rolling up or down the TV screen.
HARNESS PROBLEMS Other harness problems include blowing fuses and malfunctioning controls. The repeating blown-fuse problem can sometimes be quite exasperating to solve, for short circuits have the tendency to occur in areas almost impossible te find. First, try inserting a new fuse, as old fuses age and blow without cause. If the new one also blows, you definitely have a short. The best way to approach this problem is by turning the power off and disconnecting devices that may be causing the problem, such as the TV, transformer, and PCB. Disconnect the devices by pulling off their connectors, but do not allow them to touch. If necessary, insulate them with small pieces of electrical tape. Then, connect your VOM across the terminals of the fuse block (all electrical power shut off), and set it to one of the resistance scales. This will save blowing a fuse each time you want to check the circuit. If the VOM reveals that disconnecting the devices removed the short, reconnect the devices one by one until the short returns. The last device connected is the one that is at fault. If the VOM reads a short even after the devices are disconnected, the fault must lie in the harness itself, and only patient exploration will reveal its location. First, carefully examine all the wiring, looking for terminais that may be touching, metal objects such as coins shorting connections or burned insulation. If necessary, use the VOM to check each suspected wire. MALFUNCTIONING CONTROLS One of the most common problems here is a bad potentiometer. Typically, a bad pot will cause the image to jump as it reaches a certain point. The only cure for this one is to install a new pot. If a feature that is operated by a switch (for example, joysticks, foot pedals, control panel buttons) does not operate at all, check the switch with a VOM or continuity tester to verify its operation. If the switch does not check out, replace it. If the switch is OK, you should suspect the input to the switch from the PCB. In this case, get out the harness and logic schematics and check to see what kind of input it is. In many cases, the input will be +5 VDC. Ifso, use the VOM to check its presence. Normally, the switch is used to pull a +5 VDC line LOW to GND or to pulla LOW line HIGH. If the PCB output is missing, check the wire length from the PCB. If you find the signal at the PCB trace, the wire length or connection is at fault. If not, begin exploring the PCB using the logic schematics.
A Glossary of Microprocessor Terms
MICROPROCESSOR — one or several microcircuits that perform the function of a computer's CPU. Sections of the circuit have arithmetic and comparative functions that perform computations and executive instructions.
CPU — central-processing unit. Acomputing system’s “brain”, whose arithmetic, control and logic elements direct functions and perform computations. The microprocessor section of a microcomputer is on one chip or several chips. PROM — programmable read-only memory. User permanently sets binary on-off bits in each cell by selectively fusing or not fusing electrical links. Nonerasable. Used for low-volume applications.
EPROM — erasable, programmable, read-only memory. Can be erased by ultraviolet light bath, then reprogrammed. Frequently used during design and development to get programs debugged, then replaced by ROM for mass production.
ROM — read-only memory. The program, or binary on-off bit pattern, is set into ROM during manufacture, usually as part of the last meta! layer put onto the chip. Nonerasable. Typical ROM's contain up to 16,000 bits of data to serve as the microprocessor’s basic instructions. RAM — random-access memory. Stores binary bits as electrical charges in transistor memory cells. Can be read or modified through the CPU. Stores input instructions and results. Erased when power is turned off. LSI — large scale integration. Formation of hundreds or thousands of so-called gate circuits on semiconductor chips. Very large scale integration (VLS) involves microcircuits with the greatest component density. MOS — metal-oxide semiconductor. A layered construction technique for integrated circuits that achieves high component densities. Variations in MOS chip structures create circuits with speed and low-power requirements, or other advantages (static will damage a MOS chip).
Introduction to the
Z-80 CPU
The term “microcomputer” has been used to describe virtually every type of small computing device designed within the last few years. This term has been applied to everything from simple “microprogrammed” controllers constructed out of TTL MSI up to low end minicomputers with a portion of the CPU constructed out of TTL LSI “bit slices.” However, the major impact of the LSI technology within the last few years has been with MOS LSI. With this technology, it is possible to fabricate complete and very powerful computer systems with only a few MOS LSI components. The Zilog Z-80 family of components can be configured with any type of standard semiconductor memory to generate computer systems with an extremely wide range of capabilities. For example, as few as two LSI circuits and three standard TTL MSI packages can be combined to form a simple controller. With additional memory and I/O devices a computer can be constructed with capabilities that only a minicomputer could previously deliver. New products using the MOS LSI microcomputer are being developed at an extraordinary rate. The Zilog Z-80 component set has been designed to fit into this market through the following factors:
6-3
- The Z-80 is fully software compatible with the popular 8080A CPU. . Existing designs can be easily converted to include the Z-80. . The Z-80 component set is at present superior in both software and hardware capabilities to any other microcomputer system on the market today. . For increased throughput the Z80A operating ata 4 MHZ clock rate offers the user significant speed advantages. Microcomputer systems are extremely simple to construct using Z-80 components. Any such system consists of three parts:
- CPU (Central Processing Unit)
- Memory
- Interface Circuits to peripheral devices The CPU is the heart of the system. Its function is to obtain instructions from the memory and perform the desired operations. The memory is used to contain instructions and in most cases data that is to be processed. For example, a typical instruction sequence may be to read data from a specific peripheral device, store it in a location in memory, check the parity and write it out to another peripheral device. Note that the Zilog component set includes the CPU and various general purpose |/O device controllers, while a wide range of memory devices may be used from any source. Thus, all required components can be connected together in a very simple manner with virtually no other external logic.
General Purpose Registers
There are two matched sets of general purpose registers, each set containing six 8-bit registers that may be used individually as 8-bit registers or as 16bit register pairs by the programmer. One set is called BC, DE and HL while the complementary set is called BC’, DE’ and HL’. At any one time the programmer can select either set of registers to work with through a single exchange command for the entire set. In systems where fast interrupt response is required, one set of general purpose registers and an accumulator/flag register may be reserved for handling this very fast routine. Only a simple exchange command need be executed to go between the routines. This greatly reduces interrupt service time by eliminating the requirement for saving and retrieving register contents in the external stack during interrupt or subroutine processing. These general purpose registers are used for a wide range of applications by the programmer. They also simplify programming, especially in ROM based systems where little external read/write memory is available. Arithmetic & Logic Unit (ALU) The 8-bit arithmetic and logical instructions of the CPU are executed in the ALU. Internally the ALU communicates with the registers and the external data bus on the internal data bus. The type of functions performed by the ALU include: Add Left or right shifts or rotates (arithmetic and logical}
Subtract Increment
Logical AND Decrement Logical OR Set bit Logical Exlusive OR Reset bit Compare Test bit Instruction Register and CPU Control As each instruction is fetched from memory, it is placed in the instruction register and decoded. The contro! sections performs this function and then generates and supplies all of the control signals necessary to read or write data from or to the registers, control the ALU and provide all required external control signals.
Z-80 CPU Pin Description The Z-80 CPU is packaged in an industry standard 40 pin Dual In-Line Package. The I/O pins are shown in the below figure and the function of each is described.
My,
«4
="
a MREQ
ioRa RD SYSTEM CONTROL
WR
AFSH 7
HALT
cpu WAIT CONTROL INT NMI
RESET
CPU < BUSRQ BUS ry contro: )°'** \
+5V
GND
Z-80 PIN CONFIGURATION Z-80 CPU ADDRESS BUS
Dy D, D, m DATA D, BUS
Ds Ds D,
6-4
AgrAis (Address Bus) Tri-state output, active high. Aj-A,, constitute a 16bit address bus. The address bus provides the address for memory (up to 64K bytes) data exchanges and for I/O device data exchanges. I/O addressing uses the 8 lower address bits to allowthe user to directly select up to 256 input or 256 output Ports. Ag is the least significant address bit. During refresh time, the lower 7 bits contain a valid refresh address.
D,-D, (Data Bus) Tri-state input/output, active high. Dy-D; constitute an 8-bit bidirectional data bus. The data bus is used for data exchanges with memory and I/O devices.
M, (Machine Cycle one) __ Output, active low. M, indicates that the current machine cycle is the OP code fetch cycle of an instruction execution. Note that during execution of 2-byte op-codes, M1 is generated as each op code byte is fetched. These two byte op-codes always begin with CBH, DDH, EDH or FDH. M1 also occurs with 1ORQ to indicate an interrupt acknowledge cycle.
MREQ (Memory Request) Tri-state output, active low. The memory request signal indicates that the address bus holds a valid address for a memory read or memory write operation. 1ORQ (input/Output Request) Tri-state output, active low. The IORQ signal indicates that the lower half of the address bus holds a valid I/O address fora \/O read or write operation. An IORQ signal is also generated with an M1 signal when an interrupt is being acknowledged to indicate that an interrupt response vector can be placed on the data bus. Interrupt Acknowledge operations occur during M, time while I/O operations never occur during M, time. RD (Memory Read) _ Tri-state output, active low. RD indicates that the CPU wants to read data from memory or an I/O device. The addressed |/O device or memory should use this signai to gate data onto the CPU data bus. WR (Memory Write) Tri-state output, active iow. WR indicates that the CPU data bus holds valid data to be stored in the addressed memory or I/O device.
6-5 RFSH (Refresh) Output, active low. RFSH indicates that the lower 7 bits of the address bus contain a refresh address for dynamic memories and the current MREQ signal should be used to do a refresh read to all dynamic memories.
HALT : (Halt state) Output, active low. HALT indicates that the CPU has executed a HALT software instruction and is awaiting either a non maskable or a maskable interrupt (with the mask enabled) before operation can resume. While halted, the CPU executes NOP’s to maintain memory refresh activity. WAIT (Wait) Input, active low. WAIT indicates to the Z-80 CPU that the addressed memory or I/O devices are not ready for a data transfer. The CPU continues to enter wait states for as long as this signal is active. This signal allows memory or I/O devices of any speed to be synchronized to the CPU. INT (Interrupt Request) Input, active low. The Interrupt Request signal is generated by I/O devices. A request will be honored at the end of the current instruction if the internal software controlied interrupt enable flip-flop (IFF) is enabled and if the BUSRQ signal is not active. When the CPU_accepts the interrupt, an acknowledge signal (IORQ during M, time) is sent out at the beginning of the next instruction cycle. The CPUcan respond to an interrupt in three different modes that are described in detail in section 5.4 (CPU Control Instructions). NMI (Non-Maskable Interrupt) Input, negative edge triggered. The non maskable
interrupt request line has a higher priority than INT
and is always recognized at the end of the current instruction, independent of the status of the interrupt enable flip-flop. NMI automatically forces the Z-80 CPU to restart to location 00664. The program counter is automatically saved in the external stack so that the user can return to the program that was interrupted. Note that continuous WAIT cycles can prevent_the current instruction from ending, and that a BUSRQ will override a NMI. RESET Input, active low. RESET forces the program counter to zero and initializes the CPU. The CPU initializa~ tion includes:
- Disable the interrupt enable flip-flop
- Set Register | = 00x
- Set Register R =00H
- Set Interrupt Mode 0 During reset time, the address bus and data bus go to a high impedance state and all control ouput signals go to the inactive state.
BUSRQ (Bus Request) Input, active low. The bus request signal is used to request the CPU address bus, data bus and tri-state output control signals to go to a high impedance state so that other devices can control these buses When BUSRQ is activated, the CPU will set these buses to a high impedance state as soon as the current CPU machine cycle is terminated. BUSAK (Bus Acknowledge) Output, active low. Bus acknowledge is used to indicate to the requesting device that the CPU address bus, data bus and tri-state control bus signals have been set to their high impedance state and the external device can now control these signals.
CLK (Clock) Single phase TTL level clock which requires only a 330 ohm pull-up resistor to +5 volts to meet all clock requirements.
MCR Il SYSTEM P.C. BOARD JUMPER OPTIONS
VIDEO GENERATOR P.C. BOARD
# SUPER C.P.U. P.C. BOARD
JUMPER OPTIONS FOR PROGRAM MANUFACTURER EPROM NO. | swee | swe | JWH5,
JUMPER OPTIONS FOR BACKGROUND ROMS ONLY ROMS ONLY
JWH7
JW#16 | IWH17 owes #
# | + | | * |
MANUFACTURER EPROM NO. WMOUS ARS SHY #
#
- = CUT JUMPER WIRES WHERE THIS SYMBOL “*" APPEARS. # = LEAVE JUMPER WIRES IN WHERE THIS SYMBOL “#” APPEARS.
The above table illustrates the fact that the Video Generator P.C. Board used in the MCR II System has. 8 jumper wires, the SUPER C.P.U. P.C. Board usedin the MCR II System has 19 jumper wires, and the Sound I/O P.C. Board used in the MCR II System has 2 jumper wires.
All of the above Boards can be used with a variety of different SETS of EPROM chips. However, these EPROMS are not all made by the same manufacturer
6-7 and do have some internal differences. So, in order to make them function properly in their respective P.C. Boards, certain jumper wires on these Boards have to be cut. The above table tells you which jumpers to cut (depending on which EPROM set you're going to use) by showing a “*” under that jumper wire’s number. If there is NO “*” under a jumper wire’s number, THAT PARTICULAR JUMPER WIRE IS NOT TO BE CUT.
VII. Coin Door Maintenance
SPECIAL NOTE: If you have any questions about the coin acceptors in your game(s), please feel free to contact their manufacturers. Each manufacturer's name is PROMINENTLY imprinted on every acceptor mechanism. Metal mechanisms only: Metal and Plastic mechanisms: COIN MECHANISMS, INC. COINCO COIN ACCEPTORS, INC. 817 Industrial Drive 860 Eagle Drive Elmhurst, IL 60126 Bensenville, IL 60106 Phone (312) 279-9150 Phone (312) 766-6781
COIN DOOR MAINTENANCE | |
- Remove the coin acceptor mechanism as shown METAL COIN ACCEPTOR MECHANISMS in Figure 7-1. Periodically, the metal coin acceptor mechanism(s) EI Push down on the two spring loaded latches. must be removed from the coin door and cleaned. 0 While holding the latches down, pull the top of . the coin acceptor mechanism toward you.
- Make sure the power to the game is off. Cl Release the latches and lift out the coin accep-
- Unlock and open the coin door. tor mechanism.
TO REMOVE PUSH LATCHES DOWN
PLACE PEGS IN SLOTS PULL MECHANISM OUT PUSH MECHANISM IN TO REPLACE
Figure 7-1 Removing and replacing coin acceptor
7-1
- Clean the magnet of all foreign particles. See Figure 7-2. O This may be accomplished by swinging the gate open as shown in the above figure.
- Remove the cradles and undersize levers and clean the bushings. (A pipe cleaner makes a good bushing cleaner.) 0 Also clean the pivot pin.
- Whenever needed, the coin acceptor should be cleaned with hot water and cleanser in the following manner: D Place the coin acceptor in boiling water for about ten minutes.
- To lubricate the coin acceptor: O Use ONLY powdered graphite and put it ONLY on the moving parts of the coin acceptor. These parts are called out in Figure 7-3. O Be extremely careful to keep the powdered graphite away from paths that are traveled by the ccins.
- WARNING — DO NOT USE OIL TO LUBRICATE THE COIN ACCEPTOR. | CAUTION: BE CAREFUL NOT TO BURN YOU! | Ba 8. Check the coin chute for obstructions such as:
O Next, use a brush and kitchen cleaner to remove all remaining foreign matter from the unit. O Rinse the coin acceptor in clean boiling water. O Dry the coin acceptor thoroughly by using filtered compressed air to blow it dry.
GATE OPEN AS SHOWN CLEAN MAGNET BY DRAGGING A SCREWDRIVER BLADE ACROSS SURFACE
Figure 7-2 Cleaning the metal coin acceptor
7-2 paper, gum, etc.
- Reinstall the coin acceptor to the coin door. See Figure 7-1. 0 Place the two pegs at the coin acceptor’s base into their retaining slots. O Now push the top of the coin acceptor toward the coin door until it snaps in place and is heid there by the two spring loaded iatches.
- Close and lock the coin door.
APPLY POWDERED GRAPHITE HERE
UNDERSIZE LEVER
“E" RINGS
CRADLE
Figure 7-3 Lubricating the metal coin acceptor
SQUEEZE PINS TOGETHER TO UNLOCK SWING BOTH GATES OPEN
HOLDING BOTH GATES TOGETHER, PUSH UP AND PULL OUT
Figure 7-4 Opening the plastic coin acceptor
PLASTIC COIN ACCEPTOR MECHANISMS The plastic coin acceptor mechanism(s) must be removed periodically from the coin door and cleaned.
- Make sure the power to the game is off.
- Unlock and open the coin door.
- Remove the coin acceptor mechanism(s) as shown in Figure 7-1. O Push down on the two spring loaded latches. O While holding the latches down, pull the top of the acceptor mechanism toward you. CO Release the latches and lift out the mechanism.
- Squeeze the two pins indicated in Figure 7-4 together to open the mechanism and break it down into its three basic parts. O Clean the mechanism in hot soapy water. It never rusts. O Rinse the mechanism in clean hot water and allow it to dry. €] Reassemble ithe mechanism (it never needs lubrication).
- Check the coin chute for obstructions such as: paper, gum, etc.
- Reinstall the coin acceptor to the coin door. See Figure 7-5. O Place the two pegs at the coin acceptor's base into their retaining slots. O Now push the top of the coin acceptor toward the coin door until it snaps in place and is held there by the two spring loaded latches.
- Close and lock the coin door.
ACCEPTOR CAN BE SET TO ACCEPT U.S. QUARTERS ONLY OR BOTH U.S. AND CANADIAN QUARTERS.
MAGNET
SLIDE MAGNET TO EXTREME RIGHT (AS SHOWN) TO ACCEPT BOTH U.S. AND CANADIAN QUARTERS.
TO ACCEPT U.S. QUARTERS ONLY, SLIDE MAGNET TO EXTREME LEFT.
Figure 7-5 Changing the plastic coin acceptor to accept American or Canadian quarters.
7-4
NOA ANVHL iNOA d13H OL AQVa¥Y GNVLS SHOLNEIYLSIC HNO GNV 44avVLS HNO “SHAdVd SAWVYD YNOA HLIM GACIAOdd HAEWNN 33u4 TIOL FHL LY ANVdWOO DNIENLOVINNWA AVMGIN HO YOLNEIHLSIG HNOA LOVLNOD ASV31d ‘SNOILSAND SAVH THLS GNV NOILOAS SIHL HDNOYHL AVS" NOA Jl “HOLINOW “AL SANVS YHISHL ONIYIVd3d ONY DNILOOHSATENOYL NI 334930 SOINOYLO3TS NV LNOHLIM ASOHL CIV OL G30N3LNI SI GNV YANNVW GNVLSH3SO0NN OL ASV3 NY NI C101 SI NOILOJS SIHL NI GANIVLNOO NOILWANYOSNI SHL ‘LON ASV3T1d
Color T.V.
Color T.V Monitor
Introduction: (How to use this section of your manual.)
This section has been designed to simply familiarize you with one of the more mystical components in your game — the T.V. monitor. If you are an electronics technician who is quite knowledgeable on the subject, you may decide to just go to the schematics and start troubleshooting the defective monitor. But if you are like most people, a monitor is a T.V. set, and that means a complex doo-dad that means big buck repairs. This isn’t necessarily so. This section of the manual will acquaint you with the monitor and could just help you repair it if you feel adventurous enough to give it a try. If you have any knowledge of electronics, especially the use of a voltmeter, the repairs you can make are astonishing. Just keep in mind that ELECTRICITY CAN BE VERY DANGEROUS, SO BE CAREFUL!!
\f you want to understand how a monitor works, just read the “THEORY OF OPERATION" subsection. If you wish, you can follow along with the schematics. The information is presented in a very basic manner but more complete treatment of the subject can be found in the technical sections of bookstores.
If you want to attempt to repair your monitor, it would be a good idea to read this whole section beginning to end before starting. Pay attention to all warnings
8-1 and take them seriously. The more equipment you have the better, but a low cost Volt-Ohm-Milliameter can often, do the trick. Here are the steps to take:
- Find the symptom that matches the problems your monitor has in the “SYSTEM — DIAG- NOSIS” subsection. The diagnosis tells the circuit or area the problem may be in and possibly even the actua! component causing it. 2, Once you have the circuit that is causing the trouble, read the “TROUBLESHOOTING” subsection to learn the procedure for finding the bad part.
- Next, go to the schematic section and find the schematic that matches your monitor..It may be helpful to read the “DIFFERENCES BETWEEN MONITORS” subsection if you are unsure of which monitor you have. Use the schematic to see what paris are in the offending circuit.
That really is all there is to it. Just remember that there are some bizarre or rare symptoms not covered, or that a monitor may have two or more different problems that only a genius, the experienced, or an experienced genius can figure out. But be patient, follow safety precautions, and remember that there is also literature available from the monitor companies through your distributor or from Midway Manufacturing Company on request. (There is a toll free number on the back side of the front cover of this manual.)
Symptom Diagnosis
1. Insufficient width or heighth: A. Horizontal line (due to VERTICAL CIR- CUIT DEFECT). C Bad yoke. O Bad vertical output section. CO Open fusible resistor in vertical section. C Bad height control. C Bad flyback. B. Vertical line (due to HORIZONTAL CIR- CUIT DEFECT). O Bad yoke. 0 Open width coil. O Open part in horizontai output section. . Picture spread out too far or crushed in certain areas: A. Horizontal or vertical output transistor. B. Bad component in output circuitry. Line too close with black spacing: A. Problem in vertical section causing poor linearity. Poor focus and convergence: A. Bad high voltage transformer (“flyback”) or control. B. Focus voltage wire not connected to neckboard terminal. Colors missing; check: A. Interface color transistors. B. Color output transistors. C. Cracked printed circuit board. D. Color circuits. E. Video input jack. Picture not bright enough: A. Weak emission from picture tube. (Turn horizontal sync off frequency and put brightness all the way up for about 15 minutes. Occasionally this cures the problem.) Silvery effect in white areas; check: A. Beam current transistors. B. Weak picture tube emission. Too much brightness with retrace lines; check: A. Beam limiter transistors. B. Brightness and/or color blanking control set too high. Increasing brightness causes an increase in size and poor focus. A. Weak high voltage rectifier or regulation (high voltage unit).
8-2 10.
11.
12,
13.
14.
15.
16.
17.
18,
19. Small picture and/or poor focus: A. Low B+ voltage (power supply trouble).
Vertical rolling: A. Vertical oscillator transistor, IC, or circuit. B. No sync from logic board.
Horizontal line across center: A. Vertical output circuit is dead (see symptom No. 1. A.). B, Vertical oscillator is not putting out the right wave form. Picture bends: A. Horizontal sync needs adjusting. B. Magnetic or electromagnetic interference.
Flashing picture, visable retrace lines: A. Broken neck board. B. Internal short circuit in the picture tube (arcing). Unsymmetrical picture or sides of picture: A. Defective yoke.
No brightness, power supply operating — No high voltage for the picture tube; check: A. Horizontal oscillator. B. Horizontal amplifier and output. C. Flyback transformer (high voltage unit).
No brightness, high voltage present; check: A. Heater voltage to the tube at the neck board. Screen-grid voltage for the tube. Focus voltage. Grid to cathode picture tube bias, gon
Ne high voltage; check: A. For AC inpui to the “flyback”. B. Horizontal deflection stages. C. Flyback transformer. D. Yoke. E. Power supply.
No horizontal and vertical hold; check: A. Sync transistors and circuit. B. Wires and jack from logic board to the monitor. Wavey picture — (power supply defect); check: A. Transistors, diodes, electrolytic capacitors in the power supply.
21.
22.
23. Moving bars in picture: A.
B. Ground connector off between monitor and logic boards. Defect in the power supply (see wavy picture symptom).
Washed out picture (see picture not bright enough): A. Check video signal at the cathode pins with an oscilloscope. If there is about 80 volts peak to peak, the picture tube has weak emission.
Monitor won't turn on: A. Problem in the power supply: Check fuse, transistors, open fusible resistor.
B. Shorted horizontal output transistor. c. D. Defective high voltage disabling circuit. Crack(s) somewhere on main chassis board.
24, Can't adjust purity or convergence:
A.
5 Of
m Use a degausser to demagnetize the picture tube carefully following your degausser’s instructions. Picture tube defective. Metal foreign material is in picture tube shield. Nearby equipment is electromagnetically interferring. The poles of the earth are pulling off the purity. Poor focus or width of picture.
Guide To Schematic Symbols
THERMISTOR (POLARITY DOESN’T MATTER)
SY UW INDUCTOR, COIL, CHOKE (POLARITY DOESN'T MATTER)
(-) CATHODE
(+) ANODE
ZENER DIODE IRON CORE TRANSFORMER (SUCH AS A FLYBACK)
nO a FUSE (POLARITY DOESN'T MATTER)
CATHODE (-)
ANODE (+)
DIODE
couzcton COLLECTOR a
BASE ———> BASE-———>- EMITTER ana EMITTER —
NPN TRANSISTOR PNP TRANSISTOR
MW—
VARIABLE RESISTOR, POT, CONTROL RESISTOR (POLARITY DOESN'T MATTER) (POLARITY DOESN'T MATTER)
+ 1:
LINES ARE CONNECTED ELECTROLYTIC CAPACITOR
LINES ARE NOT CONNECTED CAPACITOR (POLARITY DOESN'T MATTER)
hw = GROUND
Troubleshooting
Troubleshooting monitors requires experience, patience, and luck. The first step is to match the symptom the monitor displays to the diagnosis next to it in the “SYMPTOM-DIAGNOSIS” subsection. This will pinpoint the circuit the problem is probably in, and often the parts to check. Next, the circuit should be visually inspected to see if there are any parts broken, burned, or if something is there that shouldn't be, like a loose screw, etc. Some parts go bad before others and should be checked first. In fact, following is the general order in which parts usually go bad: 1, Semiconductors (like transistors, diodes, and integrated circuits). Fusible resistors. Electrolytic capacitors. Resistors. Capacitors and coils. Always remember that a monitor can bite like a snake. Even when it is turned off, capacitors hoid voitage and will discharge it to you should you be touching chassis ground. The picture tube or CRT, itself, is a giant capacitor, so avoid the flyback anode plug hole. With the monitor on, the power supply circuit and/or the flyback, which puts out at least 18,000 volts, CAN BE KILLERS! Avoid handling power transistors (usually output transistors), yoke terminals, and other high power components when the monitor is on.
8-5 healthy charge for at least a week if not longer. Even after you've discharged it once, it may still carry a residual charge. It’s better to be too careful than dead, which is why electronic equipment always carries stickers referring servicing to qualified personnel. Handle the side with the viewing screen against your chest when changing it. ALWAYS wear safety goggles when handling the picture tube.
To maintain the safety and performance of the monitor, always use exact replacement parts. For instance, the wrong components in the power supply can cause a fire, or the wrong color transistor may give a funny color to the picture. Service your monitor on a nonconductive firm table like wood, NOT METAL, and take off all of your jewelry just in case. With all this in mind, you are ready to begin troubleshooting.
Observe the picture carefully. Try to vary the appropriate control that would most likely affect your particular symptom. For example, if there is poor brightness or no picture, try turning up the brightness or contrast control. If the controls have no effect at all, chances are there is trouble with the control itself, the circuit it controls, or a nearby circuit that may be upsetting voltages. Go to the list of symptoms and determine with the schematic where the bad circuit is.
Keep in mind that capacitors hold a charge as can the picture tube (for at least a week and usually longer), and could shock you.
First, check for obvious visual defects such as broken or frayed wires, solder where it is notsupposed to be, missing components, burned components, or cracked printed circuit boards. If everything looks good up to this point, make sure that diodes, electrolytic capacitors, and transistors have their leads connected in the right polarity as shown on the schematic and the circuit board. Turn on the power and measure the voltages at the leads of the active devices such as tubes, transistors, or integrated circuits. Any voltage that does not come within at least 10% to 15% of the voltage specified on the schematic indicates either a problem with that device or a component connected with it in the circuit. The next step is to use the ohmmeter to narrow down the field of possible offenders.
To test a transistor, one lead of the chmmeter is placed on the base; and the other lead placed just on the emitter, then on the collector. A normal transistor will read either high resistance (infinite), or little resistance (400 to 900 ohms), depending on the polarity of this type transistor. Then the leads should be switched, one remaining on the base, and the other switched from the emitter to the collector. Now the opposite condition should result: the resistance should be infinite if it was iower when the other lead was on the base. Consisiantly infinite readings indicate an open, and a short is demonstrated by 0-30 ohms on most of these test readings. Finally, place one lead on the collector, then the other on the emitter. No matter which lead is used, there should be infinite resistance. Any lower reading, such as 50 ohms (which is typical on a bad transistor), indicates a short. This all sounds pretty confusing, but a little experience on a good transistor will make you an expert in no time. Usually, the lowest ohmmeter setting is used for testing transisiors. Once in a great while a transistor may check out good on this test, but may actually be “leaky” or break down only on higher voltages. If in doubt, change it. Itis also wise to check the transistor out of the circuit just in case some component in the circuit is affecting the ohmmeter reading. A diode is tested like a transistor except it only has two leads. Again, there should be high resistance one way and little resistance the other. If it tests bad, take one lead out of the Circuit in case some componentis messing up the ohmmeter reading.
Without special equipment, integrated circuits are checked by verifying the proper DC voltage on the pins and the correct AC wave form using an oscilliscope. BE CAREFUL: Shorting their pins can easily destroy them. Resistors are checked with an ohmeter and should usually be within ten percent of the value stated on them and on the schematic. You may have to desolder one lead from the printed circuit board. If you wreck the foil on the board, carefully solder a small wire over the break to reconnect the conductive foil. Capacitors are tricky. Their resistance goes up when checked with an ohmmeter which shows a charging action. As they suck up current from the meter, the
voltage goes up and so does the resistance. If you are
sure a particular circuit is giving you a problem and everything else checks out O.K., Electrolytic capacitors are prime suspects. Substitute a new one and keep your fingers crossed.
Theory of Operation
To understand what goes on inside the monitor, large general groups of circuits will be examined instead of laboriously analyzing the branches and smail circuits that make up these groups. This will help avoid confusion and aid in a basic, concrete, knowledge of what makes up a monitor.
THE POWER SUPPLY — The AC going to the monitor from the game transformer is just like the voltage and current from your wall outlet. {t jumps up and down going positive and negative sixty times a second. But a monitor needs nice, smooth DC; direct current, not alternating. So diodes chop up the AC and a big electrolytic capacitor filters it out to make it even smoother. Since the monitor is a big piece of electronic equipment, with many circuits demanding a lot of power from the power supply, there are also zener diodes and transistors to help maintain a nice, constant, smooth voltage so that the monitor circuits don’t jump around. And this is what happens when you see a wavy picture. There is AC creeping through the power supply, so it must be malfunctioning. If the voltage from the power supply is too low, the other circuits will be starved for power and you may see a small, wavy picture, or noneatail. Some circuits receive voltages that are higher than what the power supply should put out. But they come from the flyback transformer which will be discussed later.
THE INTERFACE SECTION OF THE CHASSIS — The interface section of the chassis is fairly easy to identify. It is right by the place where the video jack(s) from the logic board(s) plug into. There are sets of transistors that receive the separate red, green, blue, and sync information from the cables that come from the logic boards. The circuits jack up the voltage and match impedances, or in other words, prepare the logic board outputs for the circuits that will really amplify them for the output devices such as the yoke in the case of the sync, or the picture tube that shows the colors.
An interesting aside is that our sync is composite negative sync. That means two things:
- The sync is a negative going wave form
- There are two pulses going at different speeds over the same wire: a. Vertical wave forms at 60 times per second (or Hertz) and b. Horizontal wave forms at about 15,750 times per second (Hz). The sync is amplified by a sync amplifier transistor and sent on its way to the oscillators. The sync or timing information will be explained along with the oscillator shortly. The color information is sent via wires to the neck board where the main amplification occurs. This will also be discussed later.
VERTICAL AND HORIZONTAL DEFLECTION— After the sync signal is amplified by the sync amp, it goes to two different sections, the vertical and horizontal circuits. Basically, the sync signals are for timing so the picture doesn't mess up since it is assembled like an orderly jigsaw puzzle, but so fast that you can't see the electron beams for each color painting the picture on the screen. This will all become clear soon. For now, we will follow the 60 cycle component of the sync as it goes on its journey to the deflection yoke. The 60 cycle pulse goes to the vertical oscillator to make sure this circuit goes back and forth (or oscillates) at 60 times a second. Without this pulse keeping the circuit at the correct speed, it may get lazy and oscillate at 58 cycles or lower, or get ambitious and oscillate at 62 cycles or higher. At the wrong speed, the picture will start to roll up or down. A Wells Gardner 13” (K4806) or 19” (K4906, K4956) color monitor uses an integrated circuit for its sync section. An Electrohome 13” or 19” color monitor uses an integrated circuit 1C501 for its sync section. Wells Gardner uses HA11423 and Electrohome uses HA11244. These ARE NOT interchangeable! The idea is all the same. The output to the vertical amplifying transistors for all monitors must form a sawtooth wave form, sort of like a bunch of pyramids, racing through the yoke's vertical coils at 60 times a second.
Along the way to the output transistors, the 60 cycle pulse is shaped and amplified to do the job: the yoke magnetically pushes the electron beam to fill the screen out sideways looking at the screen with the greatest length going up and down. Or viewing the screen sitting like a home television set, the amplified vertical output fills the screen up and down. Watching a monitor like this, seeing only a horizontal line means a problem with the vertical coils of the yoke or anything from the vertical output section on back to the oscillator.
8-7 The horizontal section is very similar with a few exceptions. The horizontal wave shape is more like a square and has a frequency of 15,750 cycles a second. Both Wells Gardner and Electrohome use the other side of their respective integrated circuits for the horizontal circuitry. If the oscillator isn’t going at the correct speed, the picture may move sideways, start to slant, or tear up with slanted thin figures. With both the vertical and horizontal of all monitors, there are variable resistors that change the speed of the oscillators up and down. This way you have controls that can make the correct frequencies to keep the electronic jigsaw puzzle nicely locked in place. If you're driving in acarand next to you someone else is driving their car at exactly the same speed, it will appear that they are not moving. And this is why the sync frequency and the oscillator’s frequency must match, so the picture doesn’t appear to move. The correct wave form is shaped and amplified in the circuitry just like in the vertical section. But the horizontal output transistor is a large power transistor and not only serves to give current to the horizontal yoke windings, it also feeds the flyback transformer.
THE FLYBACK TRANSFORMER (OR HIGH VOLTAGE UNIT) — The picture tube needs high voltage to light up, and the power supply can't meet this demand. The flyback transformer receives current alternating at about 15,750 times per second from the horizontal output transistor. The “flyback” jacks up its input voltage and puts out a higher voltage alternating at the same speed. But, in your “flyback” there are diodes that chop up the alternating voltage to make it asmooth DC output just like in the power supply. This is what goes through that thick red wire to your picture tube. THIS AREA HAS ABOUT 18,000 VOLTS ON IT AND IT CAN KILL YOU! The “flyback” may be dangerous, but it is also generous. It has extra output windings which give voltage to the heater pins of the picture tube, voltage for the vertical deflection circuits, and picture tube screen-grid voltage. So in a way, the high voltage “flyback” is like a second power supply.
COLOR CIRCUITS — The color circuits are pretty straight forward. The signals go into the interface section where some amplification and impedance matching occurs. These circuits are pretty sparse and simpie. Each color just has two transistors and a diode with some resistors and capacitors. From here, the AC color signal is sent by wires to the neck board. The color output circuits are on the neck board. The color signals going to the transistors are controlled by two variable resistors called drive controls. There are only two, one for the red and one for the green.
The blue doesn't have one. In the emitter part of each transistor is another variable resistor that is the cut off control. These controls vary the amount of amplified AC signal that goes to the cathodes of the picture tube. The more signal, the more color. The bases of each of these transistors are connected together and are all connected to the blanking and beam limiting transistors which are in the interface section. The beam limiter helps control the brightness level, and the blanking transistor rapidly turns the picture tube on and off so that retrace lines don't show up on the screen. By turning up the brightness on a good monitor, these four to six retrace lines can be seen slanting diagonally across the picture.
PROTECTION CIRCUIT — To protect the high voltage section against voltages that are too high coming from the power supply which could cause X-rays to be emitted from the “flyback”, a circuit senses the higher power supply voltage, and using a transistor, turns off the horizontal oscillator. Since the horizontal oscillator doesn't work, the horizontal output transistor has nothing to feed the “flyback” which in turn has nothing to feed the picture tube. The monitor will be silent, have no picture, and will appear to be off. But don’t be fooled. There is still that excessive amount of voltage coming from the power supply. To find out, check at pin two of Wells Gardner's 1C501 and emitter of X04 for the Electrohome monitor. Here are the voltages you should receive:
Wells Gardner Electrohome 130VDC 120VDC The best place to measure this voltage on an Elecirohome monitor is at a pin marked B1 on the chassis. This is because a 13 inch color Electrohome monitor, The GO07-FBO or G07-902, has an integrated circuit and very little else in the power supply. Still, there should be 120VDC at B1.
THE PICTURE TUBE (OR CRT) — The picture tube or CRT is an output device. {n other words, the end result of the circuit's work is displayed by this part. Actually, the output of other circuits is in the neck of the picture tube. First, there is the heater. The heater boils off electrons from the cathodes so that they (the electrons) shoot up to the screen to excite the phosphors so that the three phosphors emit three colors of light. The cathodes are next, and again they emit electrons to turn on the tube phosphors, making it glow. The cathode can arc or short to the heater resulting in no picture and a defective picture tube. Next come the grids. The first grid is grounded. The following grid is the screen grid which receives about 300VDC depending on the brightness setting. The next grid closest to the picture tube screen is the focus grid which gets about one fifth the amount of voltage that is applied to the picture tube anode. Atter jetting from the cathode through all these grids, the electrons speed through a mask, a sheet of material with tiny holes, and then excite the tiny dots of phosphor in the inside surface of the picture tube screen. The green electron gun (or cathode and circuitry) spits out electrons which head for the green phosphors only. The same goes for the red and blue guns. The way the phosphor light blends determines the color seen. Should these electron beams become too intense, they may burn the phosphor. With the monitor off, this can be seen as a dark permanent image of the video information on the tube screen.
Differences Between Monitors
The easiest way to identify the brand of monitor you are working with, assuming you can't find the brand name written on it anywhere, is to check the color of the suction cup type insulator that houses that dangerous anode plug on the CRT. Both monitors use a red wire but the Wells Gardner anode cup is BLACK while the Electrohome anode cup is LIGHT GRAY. Unfortunately, “call-out-numbers” for parts, circuit layout, and even circuit design are similar enough to confuse the average observer. Let’s say you have an Electrohome that isn’t working. No probiem. You can scavenge parts from an old broken up one that you may have around. Now let’s say you have a Wells Gardner that isn't working. STOP! This could be a problem. There are 3. different types of Wells Gardner K4900 SERIES monitors in the games. Here are ways to identify them. K4906 (1st TYPE) — This monitor's identifying tags have BLACK ink printed on a white background. There is NO Vertical Damping Control. (This Control would be next to the Vertical Hold Contro! but this area is jumpered with a small wire instead. K4906 (2nd TYPE) — This monitor's identifying tags have RED ink printed on a white background. There 1S a Vertical Damping Control next to the Vertical Hold Control. The Damping Control provides a few more lines on the top of the monitor screen (monitor viewed as a normal T.V. would be) for any video game that may need these lines to fit the picture on the
screen. Moving the Control may distort the top part of your picture (or the side, depending on the game and how the monitor is mounted) so go ahead and move it if you are having this type of problem. To accommodate this new feature, there are a few circuit changes. ONE MAJOR DIFFERENCE BETWEEN THESE TWO VERSIONS OF THE K4906 IS THE YOKE. They look the same but notice the part numbers: K4906 WITHOUT the Damper Control: 2021111201 K4906 WITH the Damper Control: 2021111258 Since the companies like to change part numbers at the drop of a hat, the best thing to do is to request whatever part number is written on your yoke. If you should get the wrong yoke, the results will be: Picture distortion. Excessive brightness. Too much or too little vertical picture size. K4956 (3rd TYPE) — This monitor is identical to the K4906 WITHOUT the Damper Control EXCEPT the picture tube is vertically mounted and there is an additional small P.C. Board mounted on the monitor where the yoke plugs in. This monitor is used on some Cocktail Table games where the picture has to flip for the second player. Generally speaking, some games flip the picture image via the togic board programming but this monitor is used in games that flip the picture image via generation of a small signal voltage which is sent to the extra P.C. Board on this monitor. This signal voltage causes relays on this extra P.C. Board to flip the picture by reversing the horizontal and vertical signals to the yoke pins. What kind of problems can this extra P.C. Board cause? If the relays become defective, the picture won't flip. If the P.C. Board gets cracked you may have a horizontal line on the screen, a vertical line on the screen, or maybe just a dot in the center of the screen. Of course, the logic board could be defective and not sending the signal to flip the picture. in any case, some people feei that using relays is cheaper, simpler, and more reliable, so this is an advantage.
CONTROLS YOU MAY NOT TOUCH Basically, on the Electrohome monitor, you can move any control you want EXCEPT for the B1 control. This sets the power supply voltage (ideally at 120 VDC) and is located right behind VERTICAL HOLD. The 13” Electrohome DOES NOT have this control. It may also be wise not to move the VERTICAL LIN- EARITY since this distorts the picture and is hard to reset perfectly. if you do move it, turn on the Cross Hatch Test Pattern of your game and try to get the squares to the point where they are equal in size by readjusting this Linearity Control.
On the Wells Gardner monitor, brightness is adjusted by the “BLACK LEVEL” Control which is right next to the Horizontal Frequency Control. Under the Focus Control is the “SCREEN” Control which youDO NOT touch. Yes, this control does adjust the brightness, but it is used to set the CRT bias and is adjusted at the factory. When Wells Gardner sets it, they mark the position with a black mark on the knob. If you move it, be sure to realign the mark and THEN set the BLACK LEVEL Control to the brightness you desire. So, other than the SCREEN control, you may adjust any of the controls.
Parts Interchangeability
Some parts can be interchanged on all of the monitors. Here are the rules:
- You CAN swap any resistor between monitors that has the same resistance, wattage rating, and tolerance.
You CAN swap any capacitor between monitors that has the same capacitance and voltage rating. You CAN swap many of the parts between the 19" and the 13” versions of each manufacturer's monitor. BUT, be certain to compare the manufacturers’ part numbers to be positive the parts you want to interchange are identical. BE SURE you have read the section DIFFERENCES BE- TWEEN MONITORS which was covered earlier. You CANNOT swap any picture tubes between monitors!! In the past you could, but Wells Gardner is now using a new monitor. When ordering a replacement picture tube, ALWAYS SPECIFY THE PICTURE TUBE NUMBER! You CANNOT change any part that is a safety part, one that is shaded in gray on the schematic; it MUST be IDENTICAL to the original. To do otherwise IS DANGEROUS. For instance, the 13 inch Electrohome (G07-902) monitor “flyback” looks identical to the 19 inch Electrohome (G07- 904) monitor “flyback”. In fact, there is evena 19 inch Electrohome (G07-905) monitor (which is an obsolete model) with a similar looking “flyback”. NONE OF THESE ARE INTER- CHANGEABLE! You CAN change any of the parts between the G07-904 and G07-907. They're essentially the same monitor except that the G07-907 has a vertically mounted picture tube. If there is any doubt about what parts can be swapped between each manufacturer's 19 inch and 13 inch models, compare the manufacturer's part number between each one. If they match up, they are the same part.
19” COLOR MONITOR SCHEMATIC DIAGRAM
MODELS 19K4901, 19K4906, 19K4951, 19K4956 Power Supply Voltage and Symbols
| [ Symbol __| Voltage | Operating Clreult | | | OSCILLOSCOPE WAVEFORM PATTERN | ||
| ® | 15V_ | Vert. Osc. | CAUTION: FOR CONTINUED SAFETY, | : | The waveforms shown are as observed on the wide band | |
| | Sync | | | REPLACE SAFETY CRITICAL COM: © 4 | oscilloscope with the monitor turned to a reasonably | ||
| Blanking | . | | | PONENTS ONLY WITH MANUFAC. - | strong signal and a normal picture. The voltages shown | |
| CRT Cut-Off | 1 THIS PRODUCT CONTAINS CRITICAL | | | TURER'S RECOMMENDED PARTS. | ' | on each waveform are the approximate peak ampli- |
| yaov | Horie. o: | | | ELECTRICAL AND MECHANICAL PARTS | Ee _ AVERTISSEMENT: | POUR MAINTENIR | tudes. |
| loriz, Ose, | | | LE DEGRE DE SECURITE DEL’APPAREIL | If the waveforms are observed on thi | iN | ith |
| @ | Horz. Drive | | | NE REMPLACER LES COMPOSANTS ] | a poor high frequency response. pasion | N |
| Horz. Output | | | DONT LE FONCTIONNEMENT EST | : | : |
pulses will tend to be more rounded than those shown and the ampiitude of any high frequency pulse will tend to be less. CRITIQUE POUR LA SECURITE QUE PAR DES PIECES RECOMMANDEES PAR LE FABRICANT. Vert. Output FOR REPLACEMENT PURPOSES, USE ; f
| @ | 175V | Video Output | ONLY TYPE PARTS SHOWN IN THE |
351 COLLECTOR 401 40 4 OS oN Bur SGP Bur 29C2068.8/.86% 25C20681.8/ 0% 25¢2068 81 B8K| 2SCISISBVC/CVC 2SCIBISBVEKVC 25CISI4BVC-VE Ax* ls) 19ViTP22
1VIDIV 200uSECIDIV 20VIDIV 10uSECIDIV O.5IDIV SMSECIDIV ascisisr/cR wCsas 2 Z
| 1P.1 0¢ coupLep | rp | fe | iF | | fing rey |
| BOTTOM LINE 0 VBC | Say | |B Seu | one = | |
| i | essere | 330P | 22 | Teg08" |
| eb “2c 845 | cieisy/o | Sseleisy/ |
[Foire oe _az08 C845 1402-3
[c.DRIVE)
2vIDIV 200MSECIDIV
LC. 301, PINS
20VIDIV SMSECIDIV
LC. 301, PIN 13,
1VDIV 200uSECIDIV 1VIDIV 20u SECIDIV
‘TP-31, AC COUPLED
1VIDIV 200uSECIDIV
NEGATIVE SIDE OF €303
2VIDIV SMSECIDIV i
O.5IDIV 20u SECIDIV
1.C. 901, PIN 15
+
1301 SYNC AMP VOSC H.0S Hauia23, ore sem ERS ee eer Ser [a | beste 28 HOU ers, Y) I O01) 4938!
- o20n pat ba
| | | “Tygoe | 200 | oo} | fT | (RCUTOFF] [G.CUTOFF: |
Roe 9352 HOR. OUT 2st RORIVE oe weozane 26108 tees] Bex 0
ooo82 [eax | [awa
1VDIV 2MSECIDIV
DEGAUSSING COIL (HOR.CENTERING] HV.UNIT 7382
DEFLYOKE
- K4901D, K4906D, K4951D 5833 K4956B 8-10
REPLACEMENT PARTS LIST This monitor contains circuits and components included specifically for safety purposes. For continued protection no changes should be made to the original design, and components shown in shaded areas of schematic, or A*« on parts list should be replaced with exact factory replacement parts. The use of substitute parts may create a shock, fire, radiation or other hazard. Service should be performed by qualified personnel only.
8-11 MAIN BOARD
| Ret. No. | Part No. | Description | Ref. No. | Part No. | Description |
RESISTORS RESISTORS (CONT.)
| R201 | 203X8500-645, | 1K Ohm, 5%, 1/4W Carbon | R369 | 203X5602.229 | 680K Ohm, 5%, 1/2W Comp. | |
| R202 | 203X6500-523, | 30 Ohm, 5%, 1/4W Carbon | 370 | 203X6501-002 | 33K Ohm, | 5%, 1/4W Carbon |
| A203 | 203X6500-405 | 100 Ohm, 5%, 1/4W Carbon | R371 | 203x9014-584 | 1K Ohm, 5%, 1W Metal Oxide | |
| R204 | 203X6700-327 | 100 Ohm, 5%, 1/2W Carbon | F372 | 203X9101-119 | 12K Ohm, 5%, 1W Metal Oxide | |
| R205 | 203X6700-421 | 270 Ohm, 5%, 1/2W Carbon | F375, | 203X6700-763 | 6.8K Ohm, 5%, 1/2W Carbon | |
| R206 | 203x6500-540 | 390 Ohm, 5%, 1/4W Carbon | R376 | 203X9104-404 | 270 Ohm, 5%, 2W Metal Oxide | |
| R207 | 340X2201-934 | 200 Ohm, 5%, 1/4W Carbon | R377 | 203X6500-447 | 150 Ohm, 5%, 1/4W Carbon | |
| A208 | 203X6500-540 | 390 Ohm, 5%, 1/4W Carbon | R378 | 203X6500-886 | 40K Ohm, 5%, 1/4W Carbon | |
| R209 | 340x2201-934 | 200 Ohm, 5%, 1/4W Carbon | R379 | 203X6500-886 | 10K Ohm, 5%, 1/4W Carbon | |
| R210 | 203X6500-540 | 390 Ohm, 5%, 1/4W Earbon | F380 | 203X6500-865 | 8.2K Ohm, 5%, 1/4W Carbon | |
| R211 | 340x2201-934 | 200 Ohm, 5%, 1/4W Carbon | R381 | 203X6500-724 | 2.2K Ohm, 5%, 1W Metal Oxide | |
| R214 | 203X6500-645 | 1K Ohm, 5%, 1/4W Carbon | F383 | 203X9014-387 | 150 Ohm, 5%, 1W Metal Oxide | |
| R215 | 203X6501-126 | 100K Ohm, 5%, 1/4W Carbon | R502 | 203X6500-886 | 10K Ohm, 5%, 1/4W Carbon | |
| R216 | 203X6500-645 | 4K Ohm, 5%, 1/4W Carbon | R503 | 204X 1700-535 | 150 Ohm, 5%, 15W Metal Oxide | |
| R217 | 203X6500-405, | 100 Ohm, 5%, 1/4W Carbon | R504 | 203X9014267 | 47 Ohm, 5%, 1W Metal Oxide | |
| R218 | 203X6500-645 | 1K Ohm, 5%, 1/4W Carbon | R505 | 203X6501-209 | 2.2K Ohm, 5%, 1/4W Carbon | |
| R219 | 203X6501-126 | 400K Ohm, 5%, 1/4W Carbon | R506 | 203X9104-105 | 15 Ohm, 5%, 2W Metal Oxide | |
| R220 | 203X6500-645 | 1K Ohm, 5%, 1/4W Carbon | R507 | 203X5602-185 | 330K Ohm, 5%, 1/2W Comp. | |
| R221 | 203X6500-405, | 400 Ohm, 5%, t/4W Carbon | AwREO1 | 204X 1625-058 | 3.3 Ohm, 5%, 1OW WW | |
| 3222 | 203X6500-762 | 3.3 Ohm, 5%, 1/4W Carbon | R701 | 203X9 105-141 | 2.2 Ohm, 5%, 2W Metal Oxide | |
| R224 | 203X6500-169 | 10 Ohm, 5%, 1/4W Carbon | R702 | 203X6206-441 | 2.2 Ohm, 5%, 1/2W Carbon | |
| R225 | 203X6500-169 | 10 Ohm, 5%, 1/4W Carbon | R201 | 204X2070.072 | 2K Ohm-B Semi-Fixed | |
| A226 | 203X6500:169 | 10 Ohm, 5%, 1!4W Carbon | VR301 | 204X2070-084 | 5K Ohm-B Semi-Fixed | |
| R227 | 203X6501-044 | 47K Ohm, 5%, ti4W Carbon | VR303 | 204X2070-055 | 500 Ohm-B Semi-Fixed | |
| R228 | 203X6500-645 | 1K Ohm, 5%, t/4W Carbon | R351 | 208X2070-072 | 2k Ohm-B Semi-Fixed | |
| R229 | 203X6700-421 | 270 Ohm, 5%, 1/2W Carbon | VR352 | 204x2070-072 | 2k Ohm-B Semi-Fixed | |
| 230 | 203X6500-863, | 8.2K Ohm, 5%, 1/2W Comp. | ||||
| R231 | 203X6500-863 | 8.2K Ohm, 5%, 1/2W Comp. | ||||
| R232 | 203X6500-863, | 8.2K Ohm, 5%, 1/2W Comp. | ||||
| R233 | 203X8500-468 | 180 Ohm, 5%, 1/4W Carbon | ||||
| 234 | 340X2820-934 | 82 Ohm, 5%, 1/4W Carbon | CAPACITORS | |||
| R235 | 340X2820-934 | 82 Ohm, 5%, t/4W Carbon | C201 | 203X0014-088 | 1000 uF, 16V, Electrolytic | |
| R236 | 340X2820-934 | 82 Ohm, 5%, 1/4W Carbon | 202 | 202X7200-064 | 330 pF, 500V, Ceramic | |
| R301 | 203X6500-508 | 270 Ohm5%, 1/4W Carbon | 203 | 202X7200-043 | 220 pF. 500V. Ceramic | |
| R302 | 203X6500-863 | 8.2K Ohm, 5%, t/4W Carbon | C204 | 202X7200-043 | 220 pF. 500V, Geramic | |
| A303 | 203X6500-863 | 8.2K Ohm, 5%, 1/4W Carbon | C205 | 203X0014-076 | 470 uF, 16V, Electrolytic | |
| R304 | 203X6500-724 | 2.2K Ohm, 5%, 1/4W Carbon | C206 | 203X 1810-149 | 0.1 UF, 125V Mylar | |
| A305 | 203X6500-842 | 6.8K Ohm, 5%, 1/4W Carbon | C207 | 349X2232-109 | 022 uF, 100V Mylar | |
| R306 | 203X6003-201 | 7.5K Ohm, 2%, 1/4W Carbon | C301 | 203X0014.065 | 330 uF, 50V Electrolytic | |
| R307 | 203X6500-825, | 5.6K Ohm, 5%, 1/4W Carbon | C302 | 203X1600-563 | 0.033 UF, SOV Mylar | |
| R309 | 203X6500-965 | 22K Ohm, 5%, 1/4W Carbon | 6303 | 203X0629-037 | 3.3 uF, 50V Electrolytic | |
| R310 | 203X6500-988 | 39K Ohm, 5%, 1/4W Carbon | 304 | 203X 1600-366 | 0.068 pF, 50V Mylar | |
| Ratt | 203X6500-762 | 33K Ohm, 5%, 1/4W Carbon | C206 | 203X0412.012 | 22 uF, 16V Tantal | |
| R312, | 203x9014-741 | 4.7K Ohm, 5%, 1/4W Carbon | C307 | 203x 1600-634 | 0.033 UF, SOV Mylar | |
| R313 | 204X 1450-537 | 1K Ohm, 5%, SW Carbon | 308 | 203X0025-174 | 3.3 uF, 50V Electrolytic | |
| R314, | 203X6500-481 | 220 Otim, 5%, 1/4W Carbon | 309 | 203X 1207-100 | 0.068 UF, 100V PP | |
| R315, | 203X6500-169 | 10 Ohm, 5%, 1/4W Carbon | C310 | 203X0629-061 | 10 uF, 100V Electrolytic | |
| R316 | 203X6500-762 | 3.3K Ohm, 5%, 1/4W Carbon | 311 | 203X0041-025 | 10 uF, 160V Electrolytic | |
| R317 | 203X6700-107 | 12 Ohm, 5%, 1/2W Carbon | C312 | 202X7050-248 | 4000 pF, 500V Geramic | |
| R318 | 203X6500-540 | 390 Ohm, 5%, 1/4W Carbon | 0313 | 203X0040-052 | 47 uF, 160V Electrolytic | |
| R319 | 203X6500-645 | 1K Ohm, 5%, 1/4W Carbon | C314 | 203Xx1201.265 | 0.033 uF, 200V PP | |
| R320 | 203X6501.002 | 33K Ohm, 5%, 1/4W Carbon | C315 | 203X0629-023 | 1 uF, 50V Electrolytic | |
| R321 | 203X6501-224 | 270K Ohm, 5%, 1/2W Carbon | 351 | 203X0629.023. | 1 uF, 50V Electrolytic | |
| F322 | 203X6500-886 | 10K Ohm, 5%, 1/4W Carbon | 0352 | 203X0619-045 | 47 uF, 25V Electrolytic | |
| R351 | 203x6500-886 | 10K Ohm, 5%, 1/4W Carbon | C353 | 203X1 190.015 | 0.0082 pF, 50V Mylar-PP | |
| R352 | 203X6500-785 | 3.9K Ohm, 5%, 1/4W Carbon | C354 | 203X0619-045 | 47 uF, 25V Electrolytic | |
| A353, | 203X6501-086 | 88K Ohm, 5%, t/4W Carbon | C355 | 203x 1600-366 | 0.0068 pF, 50V Mylar | |
| F354 | 203X6500-762 | 3.3K Ohm, 5%, 1/4W Carbon | C356 | 202X7050-483 | 0.01 uF, 500V Ceramic | |
| R355, | 203X2205-143, | 6.8K Ohm, 5%, 3W Metal Oxide | C359 | 202X8065-606 | 100 pF, 500V Ceramic | |
| R358 | 203X5601-878 | 56K Ohm, 5%, 1/2W Carbon | C360 | 202X7050-366 | 0.0033 pF, 500V Ceramic | |
| R360 | 203X6500-561 | 470 Ohm, 5%, 1/4W Carbon | C361 | 202X7050-483 | 0.01 uF, 500V Ceramic | |
| Reet | 203X6500-886 | 40K Ohm, 5%, 1/4W Carbon | C362 | 202X7203-032 | 0.01 uF, 50V Ceramic | |
| R362 | 203x9014-645 | 1.8K Ohm, 5%, 1W Metal Oxide | D*C363 | 203X1270-911 | 8700 pF, 1.5 KV PP | |
| We RBES | 204X 1527-751 | 3.9K Ohm, 5%, 7W Metal Oxide | C365 | 203X1201-265 | 0.33 uF, 200v PP | |
| R364 | 203X6500-246 | 22 Ohm, 5%, 1/4W Carbon | C366 | 203X0019.026 | 22 uF, 25V Electrolytic | |
| R365 | 203X6501-002 | 33K Ohm, 5%, 1/4W Carbon | C367 | 202X8065-162 | 6 pF, 500V Ceramic | |
| R367 | 203X6500-886 | 10K Ohm, 5%, 14W Carbon | C368 | 202X7203-032 | 0.01 uF, 50V Ceramic | |
| R368 | 203x5602.185, | 330K Ohm, 5%, 1/2W Comp. | 372 | 209X1207-125, | 0.1 uF. 100V PP |
MAIN BOARD (CONT.)
| Rol. No. | Part No. | Description | Ret. No. | Part No. | Deseription |
CAPACITORS (CONT.) SEMICONDUCTORS (CONT,)
| 380 | 202X7200.087 | 470 uF, S00V Ceramic | 208 | 200X3181-523 | Transistor (NPN) 2SC1815GR |
| C501 | 203x1810-149 | 0.1 uF, 125V Mylar | 207 | 200x3181-523 | Transistor (NPN) 2SC1815GR |
| 40502 | 202X7050-282 | 1800 pF, 500V Cerantic | 0208 | 200X3181-523 | Transistor (NPN) 2SC1815GR |
| 4 0503 | 202x7810-214 | 2200 pF, 128V Ceramic | 209 | 200X3181-523 | Transistor (NPN) 2SC1851GR |
| C504 | 202X7810.214 | 2200 pF, 125V Ceramic | 210 | 200X3181-523 | Transistor (NPN) 2SC1851GR |
| 508 | 203X0220.075 | 560 uF, 200V Electrolytic | 301 | 200X3181-523 | Transistor (NPN) 2SC1851GR |
| 6506 | 203x0040.034 | 22 uF, 160V Electrolytic | 302 | 200X3207-306 | Transistor (NPN) 2SC2073LBGL2 |
| 507 | 203X0041-057 | 47 uF, 180V Electrolytic | 0303 | 200X3207-306 | Transistor (NPN) 28C2073LBGL2 |
| C701 | 203X0019-092 | 1000 UF, 25V Electrolytic | 351 | 200X3248-217 | Transistor (NPN) 28C2482BK |
| e702 | 203X0634.061 | 10 uF, 100¥ Electrolytic | 0352 | 200X4589-802 | Transistor (NPN) 2SD898B |
| 703 | 202X7050-248 | 1000 pF, 500V Ceramic | accy | 200X2300-033 | IC HA11423 |
| Ak | 10501 | 200X2600-183 | IC STR3B1 |
SEMICONDUCTORS
| D203 | 201%2010-159 | Diode, 1$2076-27 | ||||
| D204 | 201X2010-159 | Diode, 1$2076-27 | TRANSFORMERS & COILS | |||
| 0205 | 201X2010-159 | Diode, 1$2076-27 | L351 | 01x47 10,198 | Coil, (RF Choke) | |
| D208 | 201X2010-189 | Diode, 182076.27 | L352 | 201X5000-083 | Coil, Horiz, Size | |
| 0207 | 201X2010-159 | Diode, 1S2076-27 | L701 | a | epee | Coil, Adg. |
| 208 | 201x2010-159 | Diode, 18207627 | 1351 | 202X1300-080 | Transformer, Hor. Drive | |
| 0209 | 201X2010-159 | Diode, 1$2076-27 | Ak 7352 | 200x9720-301 | HV-Unit M11 | |
| D301 | 201X2010-165 | Diode, ISS81 | ||||
| 302 | 201X2010-159 | Diode, 182076-27 | MISCELLANEOUS | |||
| D303 | 201X2010-159 | Diode, 182076.27 | AF501 | 204X7120.073 | Fuse, 4 Amp. 125V | |
| Dod | 201X2120-009 | Diode, RH-V | J402 | 208X5008-632 | Recep W Wire 3P-M-BG | |
| D305 | 201X2120.009 | Diode, RH-V | P201 | 204X9600-466 | Plug, PWB 3P-J | |
| D306 | 201X2010-159 | Diode, 182076.27 | 202 | 204X9601-477 | Plug, PWB 6P-Q | |
| AD501 | 201X3120.216 | Diode, RM-1AV | P401 | 204X9600-298 | Plug, PWB 4P-B | |
| 0502 | 201X3120.216 | Diode, RM-1AV | Ps01 | 204x9600-249 | Plug, PWB 2P-B | |
| 4.0803 | 201X3120.216 | Diode, RM-1AV | P60t | 204X9600-304 | Plug, PWB 4P.C | |
| ‘AD504 | 201X3120.216 | Diode, RM-1AV | THS01 | 201X0100-112 | Thermistor | |
| D505 | 201%3120.216 | Diode, RM-1AV | ||||
| D506 | 201X3120.216 | Diode, RM-1AV | ||||
| 0701 | 201x2130-204 | Diode, RU-2V | FINAL ASSEMBLY PARTS | |||
| 0702 | 201X2120-009 | Diode, RH-1V | Av 88X0138:506 | 19VLTP22 Pix Tube | ||
| 201 | 200x3181-523, | Transistor (NPN) 28C1815GR | 205x9800-158 | Lateral/Purity Assembly | ||
| 202 | 200x3181-523 | Transistor (NPN) 28C1815GR | Ae 202K1111-201 | Yoke Deflection | ||
| 203 | 200X4056-260 | Transistor (PNP) 25A562-Y-TM | ~" | 204X9301-255 | CRT Socket | |
| 204 | 200X4056-260 | Transistor (PNP) 25A562-Y-TM | 291X5004-262 | Automatic Degaussing Coll Unit | ||
| 205 | 200X4056-260 | Transistor (PNP) 2SA562-Y-TM |
NECK BOARD RESISTORS CAPACITORS
| R401 | 203X6000-729 | 220 Ohm, 5% 1/4W Carbon | 401 | 202X7050-269 | 1200 pF, 500V Cerami |
| R402 | 203X6500-540 | 390 Ohm, 5% t/4W Carbon | C402 | 202X7050-248 | 1000 pF, 500V Ceramic |
| R403 | 203X6000-861 | 820 Ohm, 5% 1/4W Carbon | C403 | 202X7050-248 | 1000 pF, 500V Ceramic |
| aoa | 203X6000-729 | 220 Ohm, 5% 1/4W Carbon | C404 | 202X7050-282 | 100 pF, 1.8KV Ceramic |
| R405 | 203X8500-540 | 390 Ohm, 5% 1/4W Carbon | C405 | 202X7060-483 | 0.01 uF, '500V Ceramic |
| R406 | 203X6000-661 | 820 Ohm, 5% 1/4W Carbon | |||
| R407 | 203X6000-729 | 470 Ohm, 5% 1/4W Carbon | |||
| oe | 203X6000-998 | 270 Ohm, 5% 4W Carbon | SEMICONDUCTORS |
203X6000-861 820 Ohm, 5% W4W Carbon ‘
| Reto | 205x904 824 | 2W MO. Forming | ace | 2o0xs206.800 | Transistor (NPN) 280206818 | |
| Ratt | 203X9104-824 | 2W W.O. Forming | 0403 | 200X3206-800 | Transistor (NPN) 2SC2068LB | |
| Ra12 | 203X9 104-824 | 18K Ohm, 5% 2W M.O. Forming | ||||
| R413 | 203X6000-998 | 2.7K Ohm, 5% 1/2W Comp. | ||||
| Rata | 203x6000-998, | 2.7K Ohm, 5% 1/2W Comp. | ||||
| R415 | 203X6000-998, | 2.7K Ohm, 5% 1/2W Comp. | MISCELLANEOUS | |||
| 9 | 401 | 208X5009-296 | RECEP W Wire 4P-E | |||
| Rat16 | 203X9105-154 | 2.2 Ohm, 5% 2W Metal Oxide | Hi | wee | ||
| R419 | 203X6500-741 | 2.7K Ohm, 8% 1/4W Carbon | 94 | aoaxee00-284 | Plug, PWB | 3P. |
| R420 | 203X6500-741 | 2.7K Ohm, 5% 1/4W Carbon | rags | 204x9800961 | Plug; Pin PD | |
| a2 | 203X6500-741 | 2.7K Ohm, 5% 1/4W Carbon | P7O1 | 20449601-020 | Plug, PWB 4P-E | |
| vR4o1 | 204x2115.014 | 500 Ohm, -B Semi-Fixed | ||||
| vR402 | 204x2115-014 | 500 Ohm, -B Semi-Fixed | ||||
| R403 | 204X2115-006 | 5K Ohm, -B Semi-Fixed | ||||
| R404 | 204X2115-006 | 5K Ohm. -B Semi-Fixed | ||||
| R405 | 204x2115-006 | 5K Onm, -B Semi-Fixed |
ee 4 a
| { | fob | Sb —— | 68E RID |
fi : i | ro — ts | Fhe ue Tor xa08x808,x808 | Ibyné ame
| Pe tae yee | x206 | | |
| se | Ww | L |
| ‘ercunD | th | 1 |
J] x20 seam waiter esasrs pi [04 SLaNKINa fk | ascasac onatcices
X901 POWER DRIVE 25¢ 2688 Re X 902 ERROR AMP 2SC1890 aes
- ne
POWER REGU Bross, asciase Loe
i ae fon eS Ae
| —] | 3 | +t | ||||||
| yo | PH | Ee | pip esimal | [exon xe | ||||
| es | re | - | ||||||
| Eis) ae rt F | ] | ae | rr | |||||
| Heelan | Cun) [Vneen] | . | - | |||||
| ; | and Wav os¢| | xso1 | | | | | faq | ||||
| TV wine ¢ | t | aah | thot | ass | f | ‘ | Pe | Schematic Notes |
Unless otherwise specified Resistance: (9) (K-*KQ, MM2Q), 1/4 (W) carbon resistor aa | Capacitance: 7 or highi F), | hi > ee } : igher—> (pF), less than 1 (yF)
| ‘uy come | uo | wes Bure | | working voltage —> 50 (V) | . |
| ee | | bend | = | ceramic Capacitor | |
| oe | hie | inductance: (vH) | ||
| ae | wae | || | Electrolytic Cap: Capacitance Value ( F)/working voitage (V), |
NP — non-polar (or bipolar) electrolytic cap.
| U=1133A | rrr | Refer to the parts list for additional component information. | ||||
| IN PCB ASSY | 7 | —_ | © | on | i | " |
| SS SO a | ae —_— | ~~ | 2 | indicates test point connection | ||
| BSeasac o 2scise | HeSGT ORsaSRa Feoece | ie neogesae | epee | sh | indicates chassis ground unless otherwise specified |
foo) & 280820 ACIZ0V 6OH:/S0He 10% Hz _ indicates cycles per second For safety purposes (and continuing reliability) aA replace all components marked with safety syrnbol with identical type.
REPLACEMENT PARTS LIST - ELECTROHOME 19”” MONITOR
Components identified by the A symbol in the PARTS LIST and on the Schematic have special characteristics important to safety. | DO NOT degrade the safety of the set through improper servicing.
Abbreviations for Resistors and Capacitors
Resistor Capacitor
| CR | : Carbon Resistor | C Cap. | : Ceramic Capacitor |
| Comp. R | : Composition Resistor | M Cap | : Mylar Capacitor |
| OMR | : Oxide Metal Film Resistor | E Cap. | : Electrolytic Capacitor |
| VR | : Variable Resistor | BP E Cap. | : Bi-Polar (or Non-Polar) |
MF R : Metal Film Resistor Electrolytic Capacitor
| CMF R | : Coating Metal Film Resistor | MM Cap. | : Metalized Mylar Capacitor |
| UNF R | : Nonflammable Resistor | PP Cap. | : Polypropylene Capacitor |
| FR | : Fusible Resistor | MPP Cap. | : Metalized PP Capacitor |
PS Cap : Polystyrol Capacitor Tan. Cap. : Tantal Capacitor
SERVICE REPLACEMENT PARTS LIST
Symbol Description Part Number
Main P.C.B. Ass'y SU-1133A CRT Socket P.C.B. Ass'y SU-3032A Purity Shield Ass'y 07-220083-03
Jiside of the P.C.B. Age’'y mot Description Picture Tube 79” . lection Yoke Magnet ’ Flyback Transf. \ AHVR 5 UNF Resisior 2200,25W K 04 C Capacitor 150pF, AC1.5KV 1 Si. Transistor 2 Si. Transistor > Screw #8-¥, Screw % x % Pix Tube Mtg. (4) Pyramidal Lock Washer (4) Nut Retainer, Pix Tube Mtg. (4) Clip -—- P.C.B. Support Standoff Wire Terminat (Gnd. Strap) Terminat Lug (Gnd.) Groundstrap Assy. Grounding Spring Wire Hook (Gnd. Strap) Purity Shield Holddown Clamp Support Brkt. RH Support Brkt. LH Chassis Base Yoke Wedge (3)
urity Shield Ass’y. Parts List Pd
mbol Description Degaussing Coil 911, D912 Rectifier 1 Amp 600V (2) Pin Terminal (2) Pin Terminal Housing Purity Shield (2 pcs.) Purity Shield (2 pes.) 911 Capacitor 1G0nF 10% 400V 321 Resistor, Wirewound 332, 4W Fire Retardent Term. Strip 4 Lug
RT Socket P.C.B. Ass’y (SU-3032A) Parts List
sistors ymbol Description
| 3105 | v | R 200 |
| 3106 | v | R 200 |
| 3113 | v | R 5K |
| 3114 | Vv | R 5K |
| 3115 | Vv | R SK |
| 3116 | OM | R 10KQ2W J |
| 3117 | OM | R 10KQ2W J |
| 3118 | OM | R 10KQ2W J |
3119 Comp. R 3.3KQ”%W K 3120 Comp. R 3.3KQ2%W K 3121 Comp. R 3.3KQ%W K
apacitors symbol Description 3107 E Cap. 10uF 250V A 3108 C Cap. 1000pF DC1400Vv P
Dils 7mbol Description 3104 Peaking Coil Part Number 17-7198-03 A29779-D = 21-141-01 A75034-B = 29-32-01 A29951-B A46600-A QRF258K-221 QCZ0101-005 2SD870 2SC1106A 31-6108738-06 31-601418-12 33-255-01 33-494-01 33-629-02 33-670-010R-02 34-228-03 34-33-04 34-574-02 35-212-03 35-3053-02 35-2348-01 35-3890-01 35-3890-02 38-449-02 39-1233-01
Part Number 21-1007-30 28-22-27 34-708-01 34-709-01 35-3847-01 35-3847-02 48-171544-62 42-113301-03 34-492-09
Part.Number QVZ3234-022 QVZ3234-022 QVZ3234-053 QVZ3234-053 QVZ3234-053 QRG029J-103 QRG029J-103 QRG029J-103 QRZ0039-332 QRZ0039-332 QRZ0039-332
Part Number QEWS3EA-106 QCZ9001-102M
Part Number QQL043K-101
Semiconductors Symbol X3101 X3102 X3103
Miscellaneous Symbol AN Description Si. Transistor Si. Transistor Si. Transistor
Description ASCRT Socket
Main PCB Ass’y (SU-1133A) Parts List
Resistors Symbol R1406 R1408 R1410 R1414 R1415 R1421 R1422 AFR1401 ASR1503 R1504 R1509 R1512 R1514 R1515 R1522 R1523 R1528 R1534 VR1501 R1703 ASR1704 4sR1901 R1902 R1903 R1904 R1905 4Q1908 ASR1909 R1910 AFR1901
Capacitors Symbol C1301 1402 ©1407 C1411 C1412 C1508 Aci512 AC1513 AC1514 C1515 1520 1523 C1824 Ac1531 Ac1532 1904 C1905 Description Vv Vv CMF OM OM OM v AF A\CMF Vv Om OM OM CMF CMF OM OM ZN ZN AXCMF A\CMF AsPosistor UNF CMF OM OM ACMF Vv AXCMF AF DDDVDVVDVDD DVVDVDVDVDVVVDVDVVVVVVVVVID 2002 2002 68Q1W J 3.3K Q1W J 27KQIW J 12KQ2W J 10KQ 6822W K 11.8KQ. 4W +1% 5KQ. 1OKN2W J B.2KQ2W J 820022W J B.201W J 4.7Q21W J 6822W J 390.21W J
39Q%W +1% 7.68KQ. %4W +1%
2Q7W K 4.723W J 1OKQ2W J 18KQ1W J 47 QW +1% 2kKQ. 2.74K QW +1% 2202%W K
Description BPE Cap. Tan. Cap. E Cap. E Cap. E Cap. PP Cap. APP Cap. APP Cap. APP Cap. PP Cap. BPE Cap. E Cap. M_ Cap. APP Cap. APP Cap. E Cap. E Cap. 3.3uF SOV A 2.2uF 16V K 4.7uUF 6.3V A 100uF 160V A 3.3uF 160V A 5600uF 50V J 2000pF DC1500V J 2000pF DC1500V J 2000pF DC1500V J 0.53uF DC1200V J 3.3uF 50V A 1uF 160V A 0.1uF 200V K 2000pF DC1500V J 1500pF DC1500V J
10uF 250V A Part Number 28C1514VC 2SC1514VC 2SC1514VC
Part Number A76068
Part Number QVZ3230-002 QVZ3230-002 QRX019J-6R8 QRGO019J-332 QRG019J-272 QRG026J-123Z QVZ3230-014 QRH024K-680M QRV142F-1182 QVZ3230-053 QRGO026J-103Z QRG026J-822Z QRG026J-821Z QRX019J-8R2 QRX019J-4R7 QRG026J-680Z QRGO19J-391 ERZ-C05ZK471 ERZ-C05DK271 QRV122F-3902 QRV142F-7681 A75414 QRFO76K-2RO QRX039J-4R7 QRG026J-103Z QRG019J-183 QRV122F-470Z QVPSA0B-023E QRV142F-2741 QRH124K-221M
Part Number QEN61HA-335Z QEES1CK-225B QEWS1JA-475 QEWS52CA-107 QEW52CA-335, QFP31HJ-562 QFZ0082-202 QFZ0082-202 QFZ0082-202 QFZ0067-534 QEN61HA-335Z QEW62CA-105Z QFM720K-104M QFZ0082-202 QFZ0082-152 QEY0034-001 QEWS2EA-106
Coils Symboi 11502 1.4603 1804
Transformers Symbol T1801 T1503
Semiconductors Symbol 1C1501 X1101 X1102 X1103 X1104 1105 X1106 X1301 X1302 X1303 X1304 X1305 X1401 x1402 X1501 X1901 X1902
D1101 D1102 D1103 D1301 D1401 D1402
1503 1504 D1505 D1506 D1507 D1508 Axp1701 A\D1901 A\D1902 A\D1903 AxD1904 AXD1905
Miscellaneous Symbol ASF1901 ASF1902
Description Part Number
Linarity Coit A39835 Width Coil €30380-A Heater Choke C30445-A
Hor. Drive Transf. A46022-BM Side Pin Transf. _€39050-A
Ic HA11244
Si. Transistor 2SC1685(R) Si. Transistor 2SA673(C) Si. Transistor 2SC1685(R) Si. Transistor 2SA673(C) Si. Transistor 2SC1685(R) Si. Transistor 2SA673(C) Si. Transistor 2SC1685(R) Si. Transistor 2SC1685(R) Si. Transistor 2SA673(C) Si. Transistor 2SC1685(R) Si. Transistor 2SC1685(R) Si. Transistor 28D478 Si. Transistor 28D478 Si. Transistor 28C2610BK Si. Transistor 2SC2688 (K.L.M.) Si. Transistor 2SC18S0A (E.F.) Si. Diode ‘WO6A Si. Diode ‘WO6A Si. Diode WO6A Si. Diode 18Z473H Si. Diode 18Z473H Zener Diode RD10F(C) Si. Diode HF-1 Si. Dicde VO9E Zener Diode RD11E(B) Si. Diode WO6A Si. Diode 18S81 Si. Diode 18Z473H AsZener Diode RD20EV2 ASSi. Diode 1S1887A ASSi. Diode 181887A ASSi- Diode 181887A ASI. Diode 181887A AdZener Diode RD6.8EV3
AsFuse 1.25A QMF53U1-1R25S AXUL Fuse 3A QMF66U1-3ROS
LE X10}. XIOS end XI0S VIDEO AMR 2SC454C g, 25c 1685 Xi¢2.x!04 ong XI06 VIOEO AMP 25A673C Morexids R@8 Vipeo OUTPUT 25ce6l! or 28Cis1av
"3014302, 308,x806 SYNC AM Beside ascieas SU-3016A lorT SOckET i
LE eoa Te W 5ME SO
X203 BEAM UMITER 258673 X04 BLANKING | Beasae pon dee
U- SU-103A MAIN PCB ASSY
Schematic Notes Unless otherwise specified Resistance: (Q) (K->KQ, MM), 1/4 (W) carbon resistor Capacitance: 1 or higher— (pF), less than 1 (yF) working voltage -> 50 (V) ceramic capacitor Inductance: (vH) Electrolytic Cap: Capacitance Vaiue (» F)/working voltage (V), Phy
x70! rot OMORVE a cosry 3bdsu NP -= non-polar (or bipolar) electrolytic cap. 2SC434C oy 25C i685 38casi or 8czei0eK Se08e9. Refer to the parts list for additional component information. AEI2OV 6OH2/SOnz 2 indicates test point connection “ ath indicates chassis ground unless otherwise specified Hz _ indicates cycles per second For safety purposes (and continuing reliability) A replace all components marked with safety symbol with identical type.
G07-FBO Parts identification on circuit boards: 00-4147-03 e.g. SU1126A (R107 = R1107) SU3030A (R113 = R3113)
REPLACEMENT PARTS LIST - ELECTROHOME 13’’ MONITOR
Components identified by the 4\ symbol in the PARTS LIST and on the Schematic have special characteristics important to safety. DO NOT degrade the safety of the set through improper servicing.
Abbreviations ior Resisiers and Capacitors
Resistor Capacitor
| CR | : Carbon Resistor | C Cap. |
| Comp. R | : Composition Resistor | M Cap |
| OMR | : Oxide Metal Film Resistor | E Cap. |
| VR | : Variable Resistor | BP E Cap. |
MFR : Metal Film Resistor
| CMF R | : Coating Metal Film Resistor | MM Cap. | |
| UNF R | : Nonfiammable Resistor | PP Cap. | |
| FR | : | : Fusible Resistor | MPP Cap. |
PS Cap Tan. Cap. : Ceramic Capacitor : Mylar Capacitor : Electrolytic Capacitor : Bi-Polar (or Non-Polar) Electrolytic Capacitor : Metalized Mylar Capacitor : Polypropylene Capacitor Metalized PP Capacitor Polystyrol Capacitor : Tantal Capacitor
Symbol
Outside of the P.C.B. Ass'y Symbol Avot AsDY01
AR11 AROS Aco4 x01 1co1 Lo1
BR BR sc WA
CH Description Main P.C.B. Ass'y CRT Socket P.C.B. Ass’y
Description AsPicture Tube A\Deflection Yoke PC Magnet Wedge AsFlyback Transf. A\Focus V R UNF Resistor 2202, 25W. K ASC Capacitor 150 pF, AC1.5KV Si. Transistor IC Regulator Degausing Coil Degausing Coil Pin Terminal (2) Degausing Coil Pin Terminal Housing Groundstrap Ass’y. Groundstrap Wire Terminal Groundstrap Spring (2) Support Bracket RH Support Bracket LH SCREW 10-% Pix Tube Mtg. (4) Pyramidai Lockwasher (4) Clip P.C.B. Support (2) Ground Lug Chassis Base
8-19 Part Number SU-1103A SU-3016A
Part Number 370ESB22(E) C29123-V A76366-A €30006 A19183-A, A46606-A QRF258K-221 QCZ0101-005 2SD869 STR383 21-1007-31 34-708-01 34-709-01 34-697-04 34-228-03 35-3560-01 35-3919-01 35-3919-02 31-631018-08 33-255-01 33-629-02 34-33-04 38-452-01
Main P.C.B. Ass'y (SU-1103A) Parts List
Resistors Symbol 1406 #1408 RI440 R1414 R1415 R1421 R1422 AXFR1401 A\R1503 R1504 R1509 R1511 R1514 R1515 R1522 R1523 R1528 R1534 VR1501 AR1703 ASR1704 A\R1901 R1902 R1903 R1904 ASFR1901 Capacitors Symbol 1402 C1411 C1412 C1508 C1511 ASC1512 AC1513 AC1514 C1515 C1520 C1524 C1904 C1905 ASC1907
Coils Symbol 11501 L1502 L1503 L1504 11901
Transformers Symbol T1501 T1503 Description Vv Vv
OM OM CMF R R g
AXCMF R A’Posistor UNF R 207WK CMF R 5.623W J OM R 10KQ2W J AF R 2002 2002, 6.801W J 3.3KQ. 1W J 2.7KQ1W J 12KQ2W J 10KQ. 6822W K 11,.BKQYUW +1% 5KQ. 10KQ2W J 5.6KQ2W J 6802 2W J B.201W JS 4.721W J 5622W J 3902.1W J
39K QW +1% 7.68K QUW +1%
2202%W K
Description Tan. E E PP E APP A\PP App PP
M E E A\MM Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. BPE Cap. Cap 2.2uF 16V K 100uF 160V A 3.3uF 160V A S600pF SOV J 47uF 160V A 2000pF DC1500V J 2000pF DC1500V J 2500pF DC1500V J 0.53uF DC1200V K 1uF 50V A . 0.1UF 200V K Cap. Cap. Cap. 10uF 250V A O.1uF AC150V Z
Description Peaking Coil Liniarty Coil Width Coil Heater Choke Line Filter
Description Hor, Drive Transf. Side Pin Transf.
8-20 Part Number QVZ3230-022 QVZ3230-022 OQRX019J-6R8 QRG019J-332 QRGO019J-272 QRG029J-123 QVZ3224-014H QRH024K-680M QRV142F-1182 QVZ3230-053 QRG029J-103 QRG029J-562 QRG029J-681 QRX019J-8R2 QRX019J-4R7 ORG029J-560 ORG019J-391 ERZ-C05ZK471 ERZ-CO5DK271 QRV122F-3902 QRV142F-7681 A75414 QRFO76K-2RO QRX039J-5RE QRG026J-103Z QRH124K-221M
Part Number QEES1CK-225B QEWS52CA-107 QEW52CA-335 QFP3iHJ-562 QEWS52CA-476S QFZ0082-202 QFZ0082-202 QFZ0082-252 QFZ0067-534 QEN61HA-105Z QFM72DK-682M QEY0034-001 QEW52EA-106 QFZ9008-104
Part Number A75360-6 A39934 C30380-A C30333-A A39475-J
Part Number A46022-BM 39050-A
Semiconductors Symbol 101501
X1404 x1402 X1103 X1104 X1105 X1106 X1301 X1302 X1303 X1304 X1305 x1401 x1402 x1501 x1701 01101 D1102 01103 01301 D1401- D1402 D1503 01504 D1505 01506 01507 D1508 Ap1701 4\01901 4A\D1902 A\D1903 £XD1904
Miscellaneous Symbol AF 1901 AF1902 Description Le.
Si. Si, Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Diode Diode Diode Diode Diode Zener Diode Si. Si. Diode Diode Zener Diode Si. Si. Si. Diode Diode Diode AsZener Diode ASi. ASi. ASi. ASi. Diode Diode Diode Diode
Description A\Fuse 1A MUL Fuse 3A
8-21 Part Number HA11244
28C1685(R) 2SA673(C) 2SC1685(R) 2SA673(C) 2SC1685(R) 2SA673(C) 2SC1685(R) 2SC1685(R) 2SA673(C) 28C1685(R) 2SC1685(R) 2SD478 2SD478 2SC2610BK 2SC1685(P-S) Wo6A WO6A WO6A 182473H 182473H RD10F(C) HF-1 Voge RD11E(B) WO6A 18881 182473H RD20EV2 181887 181887A 181887A 181887
Part Number QMF53U1-1ROS QMF66U1-3RO0S
CRT Socket P.C.B, Ass'y (SU-3016A) Parts List
Resistors
Symbol Description
| R3105 | vo | R 2002 |
| R3108 | v | R 2002 |
R3113 vooR 5KQ
| R3114 | v | R SK2 |
R3115 vVooR SKQ R3116 OM R 10K22W J R3117 OM R 10K22W J R3118 OM R 10K22W J R3119 Comp. R 3.3K2%W K R3120 Comp. FR 3.3K2%WK R3121 Comp. R 3.3KQ%WK
Capacitors
C3107 E Cap. 10uF 250V A 3108 C Cap. 1000pF DC1400V P
Colls
3101 Peaking coil
Semiconductors
X3101 Si. Transistor X3102 Si. Transistor X3103 Si. Transistor
Miscellaneous
4A ASCRT Socket
8-22 Part Number QVZ3234-022 QVZ3234-022 QVZ3234-053 QVZ3234-053 QVZ3234-053 QRG029J-103 QRGO29J-103 QRGO29J-103 QRZ0039-332 QRZ0039-332 QRZ0039-332
Part Number QEWS2EA-106 QCZ9001-102M
Part Number QQL043K-101
Part Number 2802611 2802611 2802611
Part Number A75522
| 1x Schematics and Wiring Diagrams |
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
MONITOR. | GND
COW ,D00R
| gf | gue pace | ke__p7 MONITOR |
|| rower
| - = | OS ir | ame | [Ms sack | ——— | l |
| 3 | Si-O | | | Ta] | ||
| Sic | + | obs, | |||
| 6 | Cum | STRAND | |||
| AMP | >i | ~ |
BOARD nD
| | | 42, | = | ||
| + | = — 16 POS | Eee | | ||
| gan-ca | | , | ] | | | , |
| T | SPKR | |b | 2-90910-0000_ | |) | | mt |
| | | AUDIO | GRY -BLX | POT Sap | |
| encore \$ | | | c | vou @ oe lg |
si \
oa
‘oFIRE_BUTTON a-y_'s i
| i | (Tapes | ty | | | ||
| | | eva | wove | Bet | ay lp! | |
| anna | sv, | By | | | woe eer | ve |
| elle | [ornate | ee | | |
alli ee ee ee OL
| ae | ava | alli | ae | va ls! |
| allie | een | vate! | SOUND | | |
| 3i|)|= | Te | | AN€4=S0008~Acee |
Sq } yer ee ly | iit To
| Fall bare | . | ipod | ||||
| By | | eed | a ! | ||||
| 6 | € | ] | fo | — fz | wee '2 | | |
£ LINE SHE FILTER mk 3] |
ove
T
MOBi- O0513~ A ION, 1003 TENE INSERT UGHTS
15 POS CONTE” a} 3 [
BvcOM VEL 2 ev sve 3 ASSY, BV UNREG «BWI 4 FILTER . CONN *c*
| A945 - 00002-0000 | ‘CoM | a Weis, | 9 Pos |
SV UNREG «Owe S.COMeyew? | BV UNRES #6wie | eVCOMawaTig | POWER SUPPLY ADB2 - 90412- 000 ye J be LOGIC BNO Sith +s uses (A wey MTR_RETURN weaRn! 20 P SOLAR FOX MINI MIOWAY MFG CO. 10601 W. BELMONT, FRANKLIN PARK ILL. 6031
CPU ACEa~ 91399 —
L os
| res | ims | = RED. |
| gis | ae | ‘2 FE0 |
| ' | { C | RED |
4" Losic exo 8 9! wosic oS #8 Jo! yogic Guo S. ay-8
| ' | c | “v8 |
is) RESET avi
- vparr © GRY
| a2! | + | = O8N |
| 4 | AGND_ | + yw |
J | 3P0s
J wONTOR
an!
| pe | 5 | | |
i} |
| Pi | ‘3 | i |
| a | | | | |
“+4 VIDEO. GEN ' | ALES = oCSTE = aces |
H i Pa] i i
i
NOTES 3 1, Ka BcAWRE
- a WGA. 600V. NUL WIRE
- GY GND. GOES TO ON-OFF Sw,
ano
aes
[- 4 SAFETY L sw. eke oT MONITOR Ze | FOWER. Ty vACK
INE | FILTER +
eae
1081- 008i5 - ACOS AUDIO RETURN: DO on sco pera YEeS STRAND 3 00s
| I | I | pan | ||
| 1 | 3 | SBN | : | |
| : | 7 | 1s Tew | pw | ‘gt |
| 5 | 7 | —_—+~ | ||
| | | 2Pos | gl | | - |
el | oan
| SOLAR FOX CT. | | a lkey | | | \ | |||
| y | a | 1 | MIDWAY MFG CO. | orient | Ly | 13 Pos |
« ne (0601 W BELMONT
| TT | en | \ | FRANKLIN: PARK ILL. | ' | [sey | le! |
| VOLUME | ij | i | 60131 | L | ||
| ; 2 a | d | t_J |
Lt. MONITOR SURE eee F I,
I be eee cot [
[ wala | PVR IMOVE AKT Rw | ' a! | po 4 tes ene
| smn: oo la | | : | : | ||||
| _ | re | a | . | ps! | ‘5 | | |
| —nanonvn omy | ahs | ! | | | ||||
| ua | ' | 1 | 1 | |||
| SOUND 1/0 | \ | + VIDEO | GE! | ||||
| st is | a | N | | | |||
| ial | A084 GS — A968 | aged — 99808-ases | |
\
| \ | r | 1 |
\ |
| \ | \ | | | |
| ' | pa | | lua | | |
| 1 | ' | 7 | |
| ' | ! | ! |
L J
oh
| COINDOOR & | Lie erin mur ge | | | ||
| “CONTROL | bot | ' | ||
| LIGHTS | , | 2 | P2 | red |
serie 1 '
| con | 7 | , | astros | psi | Las |
| wos SP oo unnes (EO | 3 PC | 1 | j |
Wis RETURN
| 5 | 1 | \ | \ |
| ; | Lead | 7d | ! |
id j Lod | T ' | i
| H | | | J |
one0 RED 2fED Xs BGA we T2GA.600¥ INSUL.WiRE ___sneD 3. G21 NO. GOES TO ON-OFF, ar MoniTon, cow-o00% Shan + COWL PANEL
~ “v8 ove
+c won —
DESIGNATION #
c101
C105 c106
c108 c1090
cit
c202
C204 c205 c206 cpt
R101 R102 R104 R105 R106 R107
R109 R110 Raat R112 R143 R114 R115
Rvt7 R118 R201 R202 R203 R204 R206 R206 R207
R208 R209 R210 R214 R212 R213 R214 R215 R216 R217 VR101,102
D101
D102 D103 D104 D105 0106 D201 D202 D203 D204 D205 DESIGNATION LIST
DESCRIPTION
4700ut AX. ELECT. 470ut AX. ELECT. slut AX, CER, tut AX. CER. 47pt AX. CER 470ut AX. ELECT 100ut RD. TANT tut RD. TANT. 4.7uf RD. TANT. Tut AX. CER. stuf AX, CER, -O1ul MYLAR .033uf MYLAR -O1uf MYLAR -047uf MYLAR 820pt AX. CER O1uf AX. CER. stuf AX. CER.
189hm 5W W/RES. SPACER Bohm 1/2W 5% 100hm 5W W/RES. SPACER 27ohm 1/4W 5% 2700hm 1/4W S% 6.2K 1/4W 5%
1K 1/4W 5% .16ohm 15W W/RES. SPACER 6.8ohm 1/2W5% 6Bohm 1/2W 5% 1.2K 1/4W 5% 47ohm 1/4W 5% 160ohm 1/4W 5%
S600hm 1/4W 5% 1500hm 2W 2700hm 1/4W 5% 1.2K 1/4W 5% 11M 1/4W 5% 3.3M 1/4W 5% 10M 1/4W 5% 100K 1/4W 5% 39K 1/4W 5% 2M 1/4W 5% 1M 1/4W 5% 1.2M 1/4W 5% 75K 1/4W 5% 75K 1/4W 5% 220K 1/4W 5% 3.9K 1/4W 5% 1.2K 1/4W 5% BZohm 1W 10%
2700hm 1/4W 5% 1000hm POT
ANSE AISF AIS AISF AISF 1N4001 1N4148 1N4148 1N4148 1N4001 14N4001
PROJ. ENG : L. DEKKER DESIGNATION #
Q105 Q201
ut u2 us ua
L194 8101 FA FOIA NB FE G2 Twi J3
J4
Js J6
tat
LB2
HSA1 MHHSA1
JW1-5 FBMH1,2 DESCRIPTION
2N2005 2N2005 2N4401
LM205 REG. LMa05 REG. LMag00 AN28
.22uH INDUCTOR BATTERY 3.6VDC 60DEG-C 2/8h S-BLO FUSE FUSE CLIP FERRITE BEAD TIE WRAP 9PIN P.C. MOUNT CONN(MALE) 15PIN P.C. MOUNT CONN.(FEMALE? 15PIN P.C. MOUNT CONN.(MALE) SPIN P.C. MOUNT CONN.(MALE)
FUSE TAG SYSTEM TAG
HEAT SINK ASS'Y 1 MOUNTING HARD WARE(HEAT SINK) 2-SCREW
4-WASHER 2-HEXNUT
JUMPER WIRE FERRITE BEAD MOUNTING HARDWARE
KICK
BO NOT SCALE OWG No REO © 1PER MIDWAY M i ae
a
| | wsas i |
1 | toy tol | £
ij | aio } r \E
) | 1 | 11 t li I
ty I ate -+l |, {lt | =
{
' I Dios
To!
CROSS REFFERENCE LIST
DESCRIPTION
3PIN P.C. MOUNT CONN. (MALE) 9PIN P.C. MOUNT CONN.(MALE) 15PIN P.C. MOUNT CONN.({FEMALE) 15PIN P.G, MOUNT CONN.(MALE)
22AWG T&R BARE 2.5" FG. CO.
PWR SPLY I25VAWCKT SPRT A082-S0412-B000
= MOSi os | Q'ty DESIGNATION #
Je J3 J4 JS
wWwi-5: PART #
0017-00021-0443 0017-00021-0425 0017-00021-0441 0017-00021-0440
0151-00087-0000 DESCRIPTION CROSS REFFERENCE LIST
Q'ty
47pt AX. CER. 820p! AX. CER. Otul AX. CER O1uf MYLAR 033ut MYLAR 047ut MYLAR tut AX. CER. Oeeueee
jut RAD. TANT 4.7ut RAD. TANT 100ut RAD. TANT 470u’ AX. ELECT. 470C at AX. ELECT. aweae
16ohm 15W 5% 1Bohm 5W 5%
6.8ohm 1/2W 5% 100hm 5W 5% 2Tohm 1/4W 5% 47ohm 1/4W 5% G8ohm 1/2W 5% 820hm 1W 10% an
1500hm 2W 5% 16G0hm 1/4W 5% 2700hm 1/4W 5% S600hm 1/4W 5% 1K 1/4W 5% 1.2K 1/4W 5% 3.9K 1/4W 5% 6.2K 1/4W 5%
33K 1/4W 5% 75K 1/4W 5% 100K 1/4W 5% 220K 1/4W 5% 1M 1/4W 5% 11M 1/4W 5% 1.2M 1/4W 5% 2M 1/4W 5% 3.3M 1/4W 5% 10M 1/4W 5% 1000hm POT Naeee ee seen essor sass
A1SF RECTIFIER 1N4001 1N4148, eon
2N2905 2N4401 =n
LM305 REG. 2
M3900 1 4N28 1
BATTERY 3.6VDC 60DEG-C 1 FUSE 3/84 S-BLO 1
FUSE CLIP 2 TIE WRAP. 1
FERRITE BEAD FERRITE MOUNTING HOW
22uH INDUCTOR FUSE TAG SYSTEM TAG P.c.B.
HEAT SINK ASS'Y 1 DESIGNATION
c206 201,203 cz02
€103,104,9:¢,111, cpt c108 C109
102,106 C101
R110 R101 Rit R104 R105 Ri14 R102,112 R216
Rie RIS 106,201,217. R17
R109 113,202,215 R214 R107 R207 R211,212 R206 R213 R209 R203 R210 R208 R204 R205 VR101,102
D101-*95 106,204,205 0201-203
102,105 9201
un12 us ua
8101 Ft FC1A,18 Tt
FB12
FBMH1,2 L101
HSA1 ( SEE HS ASS'Y DRAWING "¥ NOTE")
4-40 HEXNUT = 2 { 4-40X10 SLTRND 2 WSH 4-120-.250-018 4 MH HSA 1A, 2A. MHHSAIE, 2E. MH HSA 18,10 MH HSA2B,2D
- PART #
0945-00811-0100 0945-008 16-0400 0945-008 16-0100 0945-008 16-0200 0945-008 16-0500 0945-608 168-0300 0945-00811-0260
0943-0081 1-0300 0945-0081 1-0400 0845-0081 1-0500 0945-00816-0600 0945-008 11-0700
0945-00815-0190 0945-008 15-0200 0062-047D3-1XxXx 0945-008 12-0100 0082-068B3-1XXXx 0062-G86B3- 1X xx 0062-098D3- 1XxX 0062-104F5-1XXX
0945-00812-0200 0062-124B3-1Xxx 0062-13883-4 xxx 0062-16283-1XXX
0062-179B3-1XXXx 0062-183B3~1XXX 0062-20783-1XXxXx 0062-21783-1XXx 0062-25 1B3-1xxx 0062-26983- 1XXx 0062-27583-1XXx
0062-29 183- 1XXX 0062-32383-1XXXx 0062-32583- 1XxX 0062-327B9- 1xxx 0062-337B3- 1Xxx 0062-34783-1XXX 0062-37 1B3-1XXX 0945-0081 4-0000
0945-00804-0200 0945-00804-0300 0945-00804-0500
0945-00808-0300 0945--00804-0400
0945-008 13-0100 9945-008 13-0200
0945-008 13-0300
0017-00003-0377 0945-00808-0400 0017-00003-0214 0945-00814-0300
0017-00009-0225
0017-00033-0139 0945-00814-0200
M05 1-00945-A004 M05 1-00945-A009 A080-90412-B000
A945~00008-0000
0017 -00101-00727
0017-00103-0002 0017-00104-0071
| -- | 5 | 1 | 7 | fe | |
| : | avery reamite acco Oe | + anne | ie ieee | ||
| sess-oocceco09 | pat | TT NOS | : i | - | i_VIbE® nvens |
| FILTER ASS | a | 1 | i | | | | |
| i | | | mga | | | ||
| i | ivew | | | |||
| | | : | b | 4h | | | | |
| MT 89 DOMESTIC | : | Sane | rt | r) | i} |
| : | eo | se | ¢ | ||
| MTso EXPORT | -4 | | | Ree] | ° | |
| 1 | rc | i | |||
| : | i | + |
| ioe \ T aro
| ia | A | 8-6 sense vay |
| e108)
| ' | pie > | ae | wa 10% | ||||
| | | q | | | [ier “eare eno | ||||
| i | i | | | serwrarr7 | ||||
| | | NSE | f | |||||
| it | : | i | ~~ | e | |||
| | | L | common | _ | ||||
| : | Wo: oz2um | Rae | 0208 a0 | ve sear | |||
| i | \¢ | Rg Nig | " | ||||
| | | if | aos | 9? | oan | pair | |||
| i | e2dne 7 | Pineoo, | 270 | ||||
| | | | | || | 4 | i | Le | ||
| {| | | | Fase | |||||
| i] | | | w+ | B81 COUNTER oxen | ||||
| 1 | | | oy | ——— | ||||
| ; | ' | | | | | aes) | FERRITE ean | ne | 34-3 Loaic aR |
| 7 | i | i | any | ig + md | ‘34-6 LOGIC BRO | ||
| I | i | | | ang | | Sow | | oa | ||
| 1 | ii | S23 cos | |||||
| : | | | view 7 oS2 | | t |
\ me ss |
Loste ono vice neue 34-10 LBOIC ORO 8-5 AUX, ORO 35-8 CONTROLS
EARTH GND & aS-T CONTROLS Jac SENSE (OMI
35-10 _COUNTER ATH Ls
UNREG. AUX _V 5-14 CONTR. LAMPS.
‘avr cx 3108 v 'G8 _ UNREG FILTERED
| os | WeTH APPLICATION | 01 | 04 | |||||
| can | as | pee gue iso v24 4 | cig) | ||||||
| Susy | wes | — | ||||||
| 2 | = | \y | : | - | ’ | on | J srsomr | JS: CONTR.LAMPS |
| } | owe | [2 aN AUK | _ [se avoio xr | |||||
| ae | TT | ee | Jon | |||||
| i | -%, | +o | ||||||
| | E oe | _ | z | fuse | 22) | ||||
| [|| pee | > '** e201 e202 | R203 |
cern cor omen
| es | they | ae | |
| | ee mowron | | e201 | Levee | |
| SEE MECH PANEL | wweiee | TB osswr | ; |
iit i
| ioe | a | : | |
| ij | ' | I, | |
| wT e8 | “4 | 7 | : |
“Li: Pume changer - =~ ---+-/4 14-44 Ac SYNCH
nas
be e201 anaso!
a SCHEMATIC DRAWING ia Ty a0 POWER SUPPLY .90412-B000 ~ F y PROJECT ENG DEKKER wer | MIDWAY MFG. Co.
MO5!-0945-C007
L
DESIGNATION LIST
DONOT SCALE OWG NO REDO 4pER
Rimcessreciries foam Cul
Motto 4 002 s0efOATES /4/ @2
9-6 ASSEMBLY DRAWING PWR SPLY 125VA W/CKT SPRT
A082-90412-CO000 el - 00945-C006
| DESIGNATION # | DESCRIPTION | DESIGNATION # | DESCRIPTION | ||||||
| c101 | 4700uf AX. ELECT, | f | 1 | ||||||
| c102 | 470uf AX. ELECT. | Q102 | 2N2905 | =p — | _—+-] | ||||
| C103 | suf AX, CER, | 0105 | 2N2905 | ry | i | ||||
| C104 | stuf AX, CER. | o20% | 2N4401 | ; | ——y | ||||
| C105 | 47pf AX. CER. | j | _. | a6 | |||||
| c106 | 470uf AX, ELECT. | ~ | “1 | ||||||
| C107 | 100uf RD. TANT | | | HSA? | 1 | ; | | | ||||
| c108 | tuf RD. TANT. | ut | LM305 REG. | log | ! | | | |||
| ¢1098 | 4.7uf RD. TANT. | u2 | LM305 REG. | | | | | | rein | j | ||
| C110 | stuf AX. CER. | u3 | LM3900 | ty | v3 | | | |||
| ont | stuf AX, CER. | us | AN28 | id | ! | | | |||
| C201 | Otuf MYLAR | L101 | .22uH INDUCTOR | | | | | ||||
| C202 | -033uf MYLAR | B101 | BATTERY 3.6VDC 60DEG-C | i | 1 | Fa | |||
| 203 | sO1uf MYLAR | Ft | 2/8A S-BLO FUSE | if | + | | | 3 | | | |
| c204 | .047uf MYLAR | FC1A,18 | FUSE CLIP | i | ’ | ! | = | | | | |
| 205 | 820pt AX. CER. | Fez | reunien | , | | ! | ' | rca | | | |
| c208 | oO tut AX, CED | J | 9PIN P.C. MOUNT CONNAMALE) | i | io | I | com | « | | |
| v4 | 15PIN P.C. MOUNT CONNAFEMALE) | | | | a be | | | #o | ||||
| JS. | 15PIN P.C. MOUNT CONN.(MALE) | ' | i | ] | | | #8 } | |||
| R101 | -18ohm SW W/RES. SPACER | J6 | SPIN P.C. MOUNT CONN.(MALE) | 1 | | | : | | | oF) | |
| R102 | 6Bohm 1/2W 5% | | j | + | | | 7 | be-----. 4 | |||
| R104 | 100hm 5W W/RES. SPACER | 3 | |||||||
| R105 | 2Tohm 1/4W 5% | tet | FUSE TAG | i | = | ||||
| R106 | 2700hm 1/4W 5% | LB2 | SYSTEM TAG | | | | | ||||
| R107 | 6.2K 1/4W 5% | I | | | Gs | |||||
| R109 | 1K 1/4W 5% | HSA1 | HEAT SINK ASS'Y 1 | | | | | | om | |||
| R110 | .160hm 15W W/RES. SPACER | MHHSA1 | MOUNTING HARD WARE(HEAT SINK) | | | g | O | |||
| Ri | 6.8ohm 1/2W5% | 2-SCREW | I | if | g| | 3 | |||
| Ri12 | 680hm 1/2W 5% | 4-WASHER | ti | -¢l | f} | ig | + @ | ||
| R113 | 1.2K 1/4W 5% | 2-HEXNUT | i | | | 8 | ele | |||
| R114 | 470hm 1/4W 5% | | | | j | « | clos | 8 | |||
| RV15 | 1600hm 1/4W 5% | — | |||||||
| JW1-5 | JUMPER WIRE | | | m | P | 8 | ||||
| R117 | 5600hm 1/4W 5% | FBMH1,2 | FERRITE BEAD MOUNTING HARDWARE | ' | | | ss a | |||
| R118 | 1500hm 2W | sae | |||||||
| R201 | 2700hm 1/4W 5% | | | a 103 | els | |||||
| R202 | 1.2K 1/4W 5% | I | I | 3 | |||||
| R203 | 1.1M 1/4W 5% | ht | , | 8 | |||||
| R204 | 3.3M 1/4W 5% | I | i | s [| | s | ||||
| R205 | 10M 1/4W 5% | | | 3 8 | ||||||
| R206 | 100K 1/4W 5% | g 8 | |||||||
| R207 | 33K 1/4W 5% | I | |||||||
| R208 | 2M 1/4W 5% | I | 1 | ||||||
| R209 | 1M 1/4W 5% | | | | | ||||||
| R210 | 1.2M 1/4W 5% | ¥ | ° | Fi | |||||
| R211 | 75K /4W 5% | | | i | a | |||||
| R212 | 75K 1/4W 5% | | | | | ||||||
| R213 | 220K 1/4W 5% | | | 104 | | |
R214 3.9K 1/4W 5%
| R215 | 1.2K 1/4W 5% | | | | | 1 | 1 | _ | |
| R216 | B2ohm 1W 10% | | | 1 | | | 3 | | g | 8 |
| R217 | 2700hm 1/4W 5% | | | ter | | | Mel] | S | a |
| R300 | 68 | 172W5% | ial | as | ad | ||
| VRIO102 | 1000nm POT | LO vie, ee ee | se te | e) | "7 | ||
| D104 | AISF | SEENOTE 7 | |||||
| D102 | AISE | i | |||||
| D103 | ASF | i | | | | ||||
| D104 | ASF | = | — | ||||
| D105 | ASF | 1 | _ | _ |
D106 1N4001 boos ayaa CROSS REFFERENCE LIST
| B205 | Watas | DESCRIPTION | Q'ty DESIGNATION # | PART # | |
| Bros | tNaoos | 3PIN P.C. MOUNT CONN. (MALE) | 1 | JG | 0017-00021-0443 |
| 9PIN P.C. MOUNT CONN.(MALE) | 1 | J3 | 0017-00021-0425 | ||
| 15PIN P.C. MOUNT CONNAFEMALE) 1 | J4 | 0017-00021-0441 | |||
| PROJ. ENG : L. DEKKER | - | 15PIN P.C. MOUNT CONN.(MALE) | 1 | J5 | 0017-00021-0440 |
MIDWAY MFG. CO. .
| 22AWG TAR BARE 2.5 | 5 uwi-5 | 0151-00087-0000 |
CROSS REFFERENCE LIST
DESCRIPTION
47pt AX. CER, 820pt AX. CER. O1ut AX. CER .Otuf MYLAR .033ut MYLAR .047uf MYLAR jut AX. CER. Q'ty
Oaanase
tut RAD. TANT 4.7uf RAD. TANT 100ut RAD. TANT 470u' AX. ELECT. 470C st AX. ELECT. 1echm 15W 5% -18ohm SW 5% 6.Bohm 1/2W 5% 100hm 5W 5% 27ohm 1/4W 5% 4Tohm 1/4W 5% 68ohm 1/2W 5% 82ohm 1W 10% woe eee
1500hm 2W 5% 1600hm 1/4W 5% 2700hm 1/4W 5% 5600hm 1/4W 5% 1K 1/4W 5% 1.2K 1/4W 5% 3.9K 1/4W 5% 6.2K 1/4W 5%
33K 1/4W 5% 75K 1/4W 5% 100K 1/4W 5% 220K 1/4W 5% 1M 1/4W 5% 11M 1/4W 5% 1.2M 1/4W 5% 2M 1/4W 5% 3.3M 1/4W 5% 10M 1/4W 5% 1000hm POT Nese eeesanassossose
A15F RECTIFIER 1N4001 1N4148 3 o
2N2905 2 2N4401 1
LM305 REG. 2 LM33900 1 4N28 1
BATTERY 3.6VDC 60DEG-C 1 FUSE 3/8A S-BLO 1 FUSE CLIP 2 TIE WRAP. 1
FERRITE BEAD FERRITE MOUNTING
22uH INDUCTOR 1 FUSE TAG 1
SYSTEM TAG 1 P.C.B. 1
HEAT SINK ASS'Y 1 DESIGNATION
C105
C208 201,203 c202 C204 €103,104,11¢, cP1 C108 c109
102,106 C101
R110 R101 R1it R104 R105 R114 R102,112,R800 R216
R118
R115 R106,201,217. R17 R109 113,202,215 R214 R107 R207 R211,212 R206 R213 R209 R203 R210 R208 R204 R205 VR101,102
0101-195 106,204,205 0201-203
102,105 Q201
u12 us u4
B101 FL FC1A1B ™w1
FBMH1,2 L101
HSA1 ( SEE HS ASS'Y DRAWING " NOTE") 4-40X10 SLTRND 2 4-40 HEX NUT = 2 WSH 4-120-.250-018 4 “| MH HSA1A,2A. MHHSAIE, 2E. MH HSA 1B,1D MH HSA2B,20
- PART #
0945-0081 1-0100 0945-008 16-0400 0945-00816-0100 0945-008 16-0200 0945-008 16-0500 0945-G08 16-0300 .114, 0945-00811-0200
0945-0081 1-0300 0945-0081 1-0400 0845-00811-0500 0945-00816-0600 0945-0081 1-0700
0945-00815-0100 0945-00815-0200 0062-04703-1Xxx 0945-00812-0100 0062~-068B3-1XXX 0062-08683-1XXX 0062-098D3-1XxX 0062-104F5-1xXXx
0945-008 12-0200 0062-12483-1xXXX 0U62-138B3-1XXX 0062-16283-1XXX 0062-179B3~1XXXx 0062-18383- 1XXX 0062-20783-1XXX 0062-217B3-1XxX 0062-251B3- 1XXX 0062-26983-1XXXx 0062-27583-1XXX 0062-291B3-1XXx 0062-32383-1xXxXx 0062-32583-1xxx 0062-327B3-1XXX 0062-33783- 1Xxx 0062-34783-1XXX 0062-37 183-1XXxXx 0945-0081 4-0000
0945-00804-0200 0945-00804-0300 0945-00804-0500
0945-00808-0300 0945-00804-0400
0945-008 13-0100 09454008 13-0200 0945-008 13-0300
0017-00003-0377 0945-00808-0400 0017-00003-0214 0945-00814-0300
0017-00009-0225
0017-00033-0139 0945-008 14-0200
M05 1-00945-A004 M05 1-00945-A009 080-904 12-8000
A945-00008-0000
0017 - 00101-00727 0017-00103- 0002 0017-00104-0071
# NOTE: THIS RESISTOR MUST BE IN CIRCUIT FOR PROPER OPERATION.
rot
| : 1945-00002-0000 | a | see | 24-12 LOGIC BRO |
| 1. | | | VIDEO ORIVERS |
| 23-8 MISC FILTER ASs'Y
MT 89 DOMESTIC SAMP MT90. EXPORT 7 mi 2108
| i! | i | ' |
| no |
| 30 'aw | ' | ' | rc | |
| | | roe | ; | | | |
| i | | | ssooone| | | ' | coe |
| | | teeny | ' | arr | |
| 92 | ; | 15.6 “Seneca | ||
| | | : | | | 14-4 Lowe ano | |
| \ | | | | | i | |
| i | +4 | 4 —4_SENSE | 4 | |
| | | : | | | common | too |
| j | tio 8.82.aR | R216 9208 INsOOL | a | |
| oro | is | z | wea wear | |
| = | air | tot |
2 5 ste Mes evar, 7 208
| | | J | oe a | ||
| ee | = | ev | 45-1 _ COUNTER DRIVERS | |
| | | FequTE 9px | ee | 45V/7.5AMP 14-3 Looic ero | |
| | | a | “Wreue | Tt | Logic eRe |
| ui | se | | 4-8 LODIC BRO | ||
| ca | | | i | J8-2 ADE, BRO |
vaw mi
if
- 8300
| —, | if | 68 OHM I/2W & SEE NOTE | |
| | | ans 3 | | | | |
| | | + | cor | vaioa = “1° |
+ our (—* S100" 7 szome i Por
| | | aus | | |
ie | | aw7 | S60
| \ | oiMr | Leu | | | $7 ys-5 “AUK. eRD |
| : | v | a | ||
| SENSE | r™ | | | Joe contaos |
35-7 CONTROLS
| | | coMMON | _ | [ovsss mise |
ed 14-2 = SENSE (SV)
| on | TION | 45-10 COUNTER RTN | |||||
| | | ' | bo}. | + | UNREG. AUX. V | 5-14 CONTR. LAMPS. | ||
| | | \ | \ | ae | = | |||
| eav | Wr APPLICATION | | | 1 | ||||
| iy | sae | ‘B1Gi- BIoe | a700MF | 8-11 CONTR-LAMPS: | |||
| WS | H | - | oo2 | [assis au10 exe. | |||
| 6.2 | a | ore | wees | ||||
| & eay | f | : | +5y | +8v Aw | wt | | ||
| Eo | | | a | In | f | " | ||
| | | : ‘R202 | eps | 1 | ||||
| | | sov | | | ua | ets | Ite | i | |
| | | anze | ce 0202203 | of | | ||||
| || Bow | op | i eeian eel : | |||||
| Hl | — To monitor | | | Ibne | * 1 sei | Lczoz | ' | |
| WWE | SEE MECH, PANEL | | | x | | | Lhanetaa # | ye.0330e | : |
| HE cay | Fl | aE | ' | | | : | ||
| il ho | — | en | : |
Jats ac sync
| | | : | I |
| | | : | naoe ¢ dnato |
4s RERET 1 » i =—]
| e203 9208 | | inaiae | e201 | — | = | |
| ocoive Yoox) | | came abt | anaeot | proueey ENOL oexWeR | TaeNSOLARFOX | MIDWAY MFG. CO. | |
| paw 0.0870 | | I | errs | FULL | we nroe | PER. | Paani ree |
| + alee | na eee | ne | POWER SUPPLY I25VA | os! -00845 coo? | |
| ' pe | na | pe | ab | W/ekT SUPORT #082-90412-00 |
ONE SHOT ~~ 9-7
DESIGNATION LIST CROSS REFERENCE LIST
| DESIGNATION | DESCRIPTION | DESCRIPTION | QTY DESIGNATION | PART NO. | |||||
| Ci,c2 | 47? mf 28v rd.tant. | Amf 50vaxce | 6 | C7CIO, | 0986-008003100 | ||||
| C3,c4 | 22mf 6y '' | CP2CP3 | |||||||
| C5,Cé | 470mf 6v ax.elect. | 47 mf 25y rdtant 2 | Ccic2 | G986-008003100 | |||||
| C7-C10 | Amf 50v ax.er | 2amf & " | 2) | C3C4 | 0986-00800-1600 | ||||
| cPl | 220mf 25v ax elect | 220mf 25vaxelec. 1 | CPI | 0986-00800-3200 | |||||
| CP2,CP3 | Amf SOv ax.er | 470mf 6v " | 2 | csceé | 0986-00800-1700 | ||||
| RI,R2 | 2.7KN V4aw 5% .CRBN, | INVew 5% | 4 | RS-RB | 0062-026D3-1Xxx | ||||
| R3,R4 | 27m | " | 2701/4w | 2 | R3R4 | 0062-068B3-1XXx | |||
| R5-R8 | 1M | V2w | * | 27K " | 2 | RULR2 | 0062 - 199 B3-1XXX | ||
| U1,U2 | MB3730 | MB3730 | 2 | U1u2 | O066 -188X x -XX4x | ||||
| Jl | 3 PIN STRT. KKI56 | 2PINSTRTKKIS6 1 | J2 | 3000 - 16367 - 0200 | |||||
| noow | “ | i | 3000-16367 -0300 | ||||||
| ve | 3 “ | “ | u | 4° | " | . | 1 | vl | 3000 -16367 -0400 |
| HEATSINK ASSY, | 2 | HSAI, | 0986 - 00804-1800 | ||||||
| HSA1,2 | HEATSINK ASSY. | HSA2 | |||||||
| MHI-MH4 | HEYCO BUSHING | HEYCO BUSHING 4 MHI-MH4 | 0017-00042-0014 | ||||||
| PC BOARD | ' | A080 -90910-DO00 |
+ CP
MH3 [Sein] [arin _] PIN MH4 + nt ob
. PRO THIS DWG. IS CONFIDENTIAL & PROPERTY OF MIDWAY MFG. CO DIM. TOLERANCES MIDWAY MFG. CO. FRANKLIN PK., IL. 60131 A BALLY CO. DUAL PWR. AMP. ASSY aac REVISIONS A082 -90910- D000 051-00986-DOIO UNLESS OTHERWISE SPEC CONCENTAICITY TLR... 002 FRACTIONAL +1164 DECIMAL + 005 HOLE DIA + .002—.000 ANGLE 212° DO NOT SCALE DWG DATE SCALE | 12-14-81 FULL MATL
Ci wy
PIN 1
aon
o
Oo as Jl NC,
L. AUDIO
L. SHIELD
KEY
V AUDIO RETURN
R. AUDIO
R.SHIELD
V AUDIO
R-
KEY
L+
N.C
i Vaunio r
L. SHIELD
R. SHIELD
Vaupio >. + - co TO CHIP'S CPI 220ur |* | cee “Lees 25v TT TO qT Vaunio > | +
RETURN L
THIS DWG. IS CONFIDENTIAL & PROPERTY OF MIDWAY MEG. CO.
SRE MIDWAY MFG. CO. Piz-14-a1 | FULL FRANKLIN PK.,1L.60131 A BALLYCO. “ | OUAL PWR AMP
A082-90910-DOO0O DIM. TOLERANCES UNLESS OTHERWISE SPEC. CONCENTRICITY T.LR. 002 FRACTIONAL +64 DECIMAL + 005 HOLE DIA. + .002—.000 HOLE I me a DO NOT SCALE DWG REVISIONS
+ [PART NO
IMO 5 | -00986- DOI!
oO DESIGNATION
oo! cioz clos cio4 cus-c187
cet cp2-ce7 cee cPe-cri4 cps cpte-ce20 opal cp22-cp29 cP3o cpst-crae ces cp43-cre4 P88 cP 8e-cPeo, cre
om
IOI, AlOZ R03 RI04 R105 RIOS RIO7 RI08 R108, RIIO Rit Rue RUS Ria, RS, Rus RIL, Ris R120 Ria Ri2e R123 RI24 RI2s Ri28,Ri27 Rize R129 RISO RIS R132 RIBS, RIS RISS R138 RIT R38 RI38 RI40, RIAL R142, R143 Riaa’
RMI rz RMY M4, RMS awe RMT
D102
aio
9103-9108
le a2 "As aa aS ALO, Atl a2 “As “82
"39
- 810
> eu
- ei2 “ars DESIGNATION LIST
DESCRIPTION.
33°F Sov aK ME ma 300PF OME
ATOMF 1 MF 1OMF Ol MF ‘470Mr OM lowe 1 MF (0 MF 1 MF 0 MF OL MF 1OMF ol MF 470MF ‘Ol MF 470 ur
47K
rex
atk
1K
0K rd 47K K
2K 1K
to
2K K
10K lok
insei7 Nata
2Nago3 2nai23 wPsA7O
7a161 ger
Ioov MYLAR
lev tov lev
ouM
74.8367 MKs682 7ais3z 74s74 74804 HT TaLse4a EPROM EPROM EPROM MK3880 7474 7432 7as04 7aLs367 7432 van
PROJECT ENG: J:BOYDSTON ELECT. ax AX.CER AK.TANT, AK. CER. ELECT. AX AX. CER
ELECT. Ax AX.CER, ELECT.AK
aw cRAN, OESIGNATION DESCRIPTION
Ie <o 74.808
- co 7476 cu 74804 cia.cis 7420 "oa PRON Ds EPROM "08 EPROM "07 EPROM be 5418-20 "08 PALSiSS:
- plo-o13 7aLsis7 ” e@ NVR CONT " 85,68 7432 e7 ee "ee mauseaa “eo 7420
- E10 7as04 "et 7427 Fe 4083 FS 4017
- Paes 7aise2as ” Fe racs37a “FT 4801-AN Fro 7ausis7
- FIO, 7489 oe 7aLsis3
- os 7415374 oa EPROM os EPROM os 748374 “7 7ALsi53 8-al! 7489
- oi misc-T
- a3 vet 97-8 7aLsira (108-110 lOvH W.w con Cie (Own MOLD lesa 28 PIN IC SOCKET esals ee Ne
| Iesaisa | ay on | of |
IcsB3-1cs85 aaron ics87 ao" icsis zo" eS ic$p4-1cs08 aan os \csr7 men
| 1e864, 1865. | 24 | 7 |
resoiz 20" " sesolg st 1esci3a Iese4 mo" 2B1, 882 Bus BAR sw. SWITCH P.8. MTS XTALI 19.968 MHZ CRYSTAL owl. wit JUMPER WIRE ath KK-IS8 STR. 5 PI
| a | ; | 1aPIN |
a2 KK-IQ0 RT ANGLE 2PIN ve mE Si
3,94 8.6,47
A080-90009-HOOU FLEX-PAC JUMPER
ePU. 80
aevinons, | [sco o» SOLAR FOX FULL IPER| MIDWAY MFG. CO.
= cpu ASSEMBLY ORAWING
A082-90009-HO00 MOS! -CO882 A005 w
+ if ay |g
| | | oo | | | ||
| | | GD | Gr) | | | |
| [na | | [oe irse | | wa | 04 (800) | |
| | | | icsae | || tebe | | | icso0 |
| A | i | = | Fa | |
| Be | haa) | Sse8z) | Lis sera) | |
| —— | Ci | aaearcra| | ||
| [as] [es eo] | eRe) | =) | (4 | 08 (cox) |
| icses | i | | icsps | cL | 1csos |
| | | [i | L | Pa? | orig |
ED [ex
| ae | iesoe | ce | Fe | Ais |
| Toews] | lar) | cr | Ga) | |
| | | __ | aed} | ||
| a | 7) | kOe] | Pr | 7 |
| icse7 | 1eso7 | ls Capa | \ese7 | |
| | | CPE) | ces) | ||
| crso + | crt | LAER |
678 | a
oe
an
| os] | pio)
| l | : | aero |
- GD
| FARES a Bales
| a. Ee | Bi2 | 8 aes | i | |||
| rem) | sD) | BERS | | | |||
| cael | 8 | rs | ||||
| \ Seo | : | reso | 4 | |||
| $) esas | on | [es | 18 | 3)/DDDDDDDEtsas] | | |||
| 2 | _| | | | g | |||
| 3 | wD! | 43) | eoonoeee | ceria) |° | ||
| Gx) | a5) | fern | gonceee § C | |||
| SD | GD | gejggle 8293288 | ||||
| 7A | Kid | 1] [ex | Te | a | TR | | |
weal we
| DESCRIPTION | QTY _DESIGNATION | PART NO. | ||
| 8 PIN socket | 2 | IeSAI30, 1CSGi30 | 0986-00804. 3600 | |
| re | 508 | 2 | icsals, (esels | o988-00804- 3700, |
| zt | 3 | CSGI2.ICSE4 _O9R6-00804- 3600, | ||
| 38 | a | e888: | S888 S888 E50 |
\es04-1es 06, \cSF7,1¢804,1C805
| zen | \ | tcsaa | 0988-00804 -3800 | |
| fou | ' | \cser | S986-00808- 3600, | |
| aus pan | 2 | Be, bez | 0986-00806 100 | |
| SWITCH P.8. Mro | i | swi | 098e-00804- 3100 | |
| BUMPER WIRE | u | Jw | 0908-00804-3200 | |
| KKI00 RT ANOLE 2PIN- 1 | wea | 098¢-00804- 4200 | ||
| 0 | t | ePIN I | a2 | 0986-00804-4300 |
| kxise ste | sein 1 | aA | 0986-00804-4400 | |
| . | . | 14pm | vt | |
| Meiogar ants | Darin. | eur | oute—onto4-a700 | |
| FLEX-PAC JUMPER = | J3-u? | 0986- 00804-4800 |
cpu eo ‘A080-80009-Ho0o DESCRIPTION
33 PF SOV AX.CER 90°F * O1MF "
IMF 100V MYLAR IMP BOV AX.CER, NoMF 28V AX.TANT
4TOMF lev ELECT.
10 OHM /4W cReN
Wo" 6 30"
nr 470" son
xo 47k" *
wk « 8 ow
5¢0 1K 47K 47K lox a
INalse tws817
MPSA70 2Na123 2N4403
74804 racsoe 7420
vase mas32 mm 7asr4
yausise ms153 74US155 7ALSi57 7aI61 Tausi7a TaLs244 raLseas 7aL$367 T4LS374 aK 3800 uK3e82 4017 4083 ‘4B01-AN-8 Bate- 20 “7 vet van-T wisc-1 NVR conT EPROM EPROM EPROM EPROM EPROM EPROM EPROM EPROM EPROM
1owH Ww 10.08 MOLD
uz CRYSTAL CROSS REFERENCE LIST
| ary. | DESIGNATION | PART _NO. |
| ' | cio | 0986-00800-0300 |
| t | clog | 0988-00800-3000 |
ry CP2-CP7.CP9-cR14, —_0986-06800-2200 CP20,P22-chee, ¢P38,cP40-cP54, /-CP8O, CP62 -CP6: CPIIS-¢PI36.C137 ' clos 1 cloe 8 ce, cP2i,cP3o, copes 4 cPi,cPis,
e RIZ6, RI27,RIS8,RIS4, 0062-05183 -1xxx 40, R41
| ' | R108 | 0002.06383-1Kxx |
1 Rls
| 3 | Ri21,RIZ8,RI38, | (0062-11 983-1xxx |
| U | ROS, | (0062-18383 -Ixxx |
| 3 | R28 R132, R180 | (0082-13583. 1xxx |
| 2 | R108, R111 | 0082-14483-1Xxx |
| 3 | R124, RISLRISS | 0082-18603-Ixxx |
| 3 | RIOS,RII7, RUB | (0062-16288-1xxx |
| H | R120) | (0082-174B3-1xxx |
| a | RIOBRNS,RING,RIZS | 0062-17 0B3-1KXX |
RISO,RI37,RIIO.RI4g
| ' | RI04 | 0082 -18383-1Xxx |
| 3 | R122,R129,R1 | 0082-19383-1xxx |
i RIOI,RIOZ,RIO7,RIld — 0082- 2IIBS-1XxX fig R142, R143,
| t | Rue | 0062-22783-1xx x |
| ' | RMT | 0986-00804- 2800 |
| 1 | RM2 | 0986-00 804-2500 |
| 1 | RMS | 0988-00804 - 2200 |
| t | RMI | 0988-00804- 2400 |
| U | RM | 0986- 00804-2300 |
| 2 | RM4,RMS. | 0986-00804. 2700 |
| 1 | pioz | 0986-00801-0100 |
| ' | Dior | (0988-00801-0300 |
| 8 | gi03-a108 | 0986-00802- 0300 |
| fl | auo2 | 0986-00802- 0100 |
| ' | aior | ‘0¥a6-00802- 0200 |
| 4 | ‘A12,B10,C11,E10 | 0986-00803-0400 |
| ' | ca | 0986-09803-1600 |
| 3 | ci2crs.c9 | 0986-00803- 1200 |
| 1 | Eu | (0986 -00803- 8800 |
| 4 | B9,BIZ,E5.66 | 0986-00803-0500 |
| \ | ro | 0986-00803-0600 |
| 2 | “Pace | 0986-00803-100 |
| 2 | “AIQatt | 0986-00808-!500 |
| € | "FIOFII, 68,69 | (0986-00803 -i800 |
| ' | "er | 0986-00803 -I900 |
| 2 | “9267 | 0986 -00803-10c8 |
| 1 | “do | 0986-00803. 8600 |
| 6 | " D10-b13,Fa, 9 | 0986-00803-1100 |
f (0986 -00803-c100 ' 0986-00803-9300 2 '0988-00803-0800 2 0986-00803-0900 2 0986-00803-2200 3 0986-00803-0700 1 0986-00803. 7800 ‘ 0988-00803. 7700 ' 9988-00803-8700
| ' | “FR | 0988 -00803-2000 |
| ‘ | “7 | 0986- 00803- 8400 |
| ' | * ba | 0986-00803- 8100 |
| ' | nals | 0986-00803 - 8900 |
| ' | ais | 0986-00803- 9000 |
| ' | ters | 00803. 9100 |
| ' | Giz | -008 03-9200 |
| 1 | “E@ | 6-00803-3200 |
1 "a3 (PGA 1 (ee) 1 (Poe)
| L | (Poo) | OPTIONKIT: UPRIGHTS |
| ‘ | "ps (ce) | (0982-00803-0100 |
| 1 | "De (PGF) | OPTION KIT: COCKTAILS, win's |
| ' | “o7 | (0880-00803- 1700 |
t * 04 B66) ' ” G5 (Bch)
| 5 | Ltos-ut10 | 0986-00804 -0200 |
| 6 | Lu Lue. | 0986-00804 -3300 |
| 1 | xTALI | 0988- 00804-0100 |
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
| che 100 wt are EPROM lows 7A1s86 | ey f- ~18 8 | 8 sk abl a | g | 60 101 pt Sov aX.ceR.—_cPI-3, €05-10, 966-00800-2500 |
| ‘ AX, ELECT ie a2 TALSiST iene rai7e | iG 8 8 |: =| 2) SBRR | cPi2-20,cP22-27, | ||
| orestoe-er, | was 7acsis7, Ione rairs | 1A ‘ak Es a lez | cP 38-41,cP 43-47, | |
| ieeceiee. | eae TaLeae L dedied a | | | | bd bas ° ° . < 1 1K 10 PIN SIP RMS 0986-00804 -1000 | |
| [RIOI~119,201,202, 1K 1/4W 5% es 422 a6 T4LSIST | | | 2 24-2 KE, U6. 0986-00803 -2300 | ||
| 2 orm in si eine see | 60 ea ed 7 | : 7400 re ‘0988-00803 2800 | ||
| ncictel fee modi) pr | + _ «|! + | + + + + + + 1 74.330 a2 '0986-00803-4300 | ||
| 106 74.8187 Le 2u4-2 | | FE g Biel) Ss - | o o c rs Fa] (2) | 98,LTAMTANT. |
or raisers eur TaLSi87 (| 7 ‘ a Py . @ a a a az g S19 |. 6 5 08 rears onen-00808-2800 ele ies oo. a ° ra.sio4 82,3,¢2,3,02,3.2,8. 0988-00803-2500 nares pecan he, ess u + racsers bar4.n3 ‘986 00803-3000
| - g i F | 1a) fe 3 3 | 2 rausara ears (0986-00803-4000 |
ere 7400 ent 7430 . : : i rhe is a fe : 8 93422 85,6,05,6, 35, (0986-00804-0800
| crs T4048 one 427 | t 2 > = | cy » s | 5,05, M5 |
| (cre sid anil Lad Bek i9| | 3 | 3 | ' ‘PROM ch (vec) OPT. KIT: UPRIGHTS: |
- Biiies| Ion? TAUSi8T rho r F F F 8 JUMPER WIRE, win ‘0986 -0008-0200 ic oa Ta.s203 1c885,6,05,6, 22PIN IC SOCKET oe} le ' 7 ! ceed Spibieites e009) sone weusees SEMAN. se socreT U 3 220 Sooke J345 0986-00804-4700
| Wee Le, . | ' | " | 4 (28 PIN SOCKET 1CSA1,81,C1,01 0986-00804-0300 |
PROJ. ENG. ATISH GHOSH poroes sotar Fox | MIDWAY MFG. CO. See Doo sv pra FE a 446 __ be VIDEO GENERATOR P.C IMO5I-00982-A007,
| > | ae | 8082-91399-F 000 |
9-1
832 Rom (semen 9 Umar we ot HERD!
'SOLAR-FOX | wiWAY MFG. CO. SCHEMATIC VIDEO GEN. | \wosi-o0882-2008 082-91399-F000 | i
DESIGNATION
irs, ne wror- R202 boos moe DESIGNATION LIST
DESCRIPTION
pill
01 wr 8Ov ax com
Mena nc oANT
ark
ame DESIGNATION
$jLe = jiesae | resaio ses | |
DESIGNATION LIST
OESCRITION W/O__ PANNING _KiT CROSS REFERENCE LIST
DESCRITON QTY DESIGNATION PART_NO.
33K OHM 1/4w CREN 33 OHM VwCRBN 2 R403 RA04 0062- 251B3-IXxx CROSS REFERENCE LIST
| DESCRIPTION | QUANTITY | DESIGNATION | PART NO |
| 3a Pr soy 28 Ax cen | : | cue |
2 eae, C128
| 330 #F sev ax ceR | 2 | cre). cre |
Ov ur sav nx cen ” 2, cPy4-c999, cP98-c048,
| swe Sov ax com | ” | evaat eva |
| Sr 200 ax TaN | ‘ | ersr- 188. c162-6186, 6136. 27 |
Eror eres. C138, C198, €172,086-068,012
| "90 orm | : | A238 |
| 220 onw vv4w | ” | fy v6-13, Pies |
ae : ae 8 ish 3 tmok 2
| " | 2 | Nesava.1cSe6. esr? | 0986 ooace- 1500 | |
| term | ew | : | us | 3090-16966- 1800, |
| super wine | 2 | sw awe | 0986-00804-4000 | |
| @ | Position oi sw | : | wa | osee-o080s-0850 |
| SiTION OIF Sw | 1 | sw | oete-oo40s- 1000 |
PROJECT EWG: CARY MEDIICK SOLOR FOX |
.™m _ ASS'Y DRAWING SOUND 1/0 cesmrez 4082~—90908-G000 MIDWAY MFG. CO.
MOS! OO982 ACO
DESIGNATION DESCRIPTION
B79, 296 aia7- R202 a208-R208 200-21
Reie-n2i9 an0-Reae nee Reea,nage Rae? azes esi nese Ress Rese,naas Resa 307-8308 eso! go, R408
mee a8
ewe
PROJECT ENG: CARY MEDNICK W/O__ PANNING KIT
CROSS REFERENCE LIST
33K OHM 1/4w CREN 33K OHM VawcRBN 2 0062- 251B3-IxxXx
Tm + | oanrrez on Fox | MIDWAY MFG. CO.
ASS'Y DRAWING SOUND 1/0 | A082—90808-G000 MOS! 00982 AOOS | DESCRIPTION CROSS REFERENCE LIST
QUANTITY — GESICNATION PART NO
2 cree. cre
Crorerea, €131, C138, e172,c88.c68,0172
02 18883. xx
9986-00804 4000
DESIGNATION List List CROSS REFERENCE
DESCRIPTION QUANTITY DESIGNATION
| DESCRIPTION | DESIGNATION | cESCRIPTION | a2 pF sov se ax cen | : | cise | ||||||||
| : | “47 PF SOV AK CER | 2 | e128, C128 | ||||||||||
| siow-es0 | vo we asv ara | 010%-0109, 9105-1 | neva | fs | |||||||||
| ev? | MF Nov a ce | 0101-0109 | 1 10 | 100 PF sav 5% AX CER | ' | cue | |||||||
| cine e128 | “er sov Ax cen | ove | aneaos | ae br exw are | ? | crt c1es | |||||||
| : | 0622 MF 100V 10% MYLAR | 12 | c14s-c156 | ||||||||||
| cn | some a5v ax aN | wm | rave | [047 ME s00V MYLAR | 1 | cna | |||||||
| engerar | 1 MF 200 be Tat | oa | rats279 | 5 | (21 MF Sov AX CER | 50 | cr2-cP12, CP4-CP32, CP35-CP4E, | ||||||
| cre | 10 MF 250 AK YANT | rn | rausare | ; | erasers. cvao, c14:.C173 | ||||||||
| 39 | 047 ME SOV MYLAR | cay | skxe RAM | ee | LIME Sov Ax CER | ” | crnzt27 e143 | ||||||
| cro cuts | (21 FB0V Ax CER | a | sowcrsow 0 | | | “ue 20v Ax TANT | . | c1s7-159, cre2-c104, C134, 6137 | ||||||
| cur | 100 PF SOV AK CER | dd | sot | 10 ME 28v AX TANT | 16 | cP34,cPs2:cPs3, CP201-CP204 | |||||||
| “ | eo we nov ax ce | a | Dole | e101-c193. 6199, 6198, C172,068.0068 | |||||||||
| evs | TAPP SV AESER | eat | ial | -* 2 | 470 MF 16V Ax ELECT | « | Pr. CPI. CRAT, CPE | ||||||
| cas crse | 40022 MeIQOY 10% WAR | a | raisees | ||||||||||
| crs-c1sa | Ye aby ax TANT | wien | P80 cru | 73 | 22 ow aw | ' | |||||||
| cies | 330 PF ov Ax ct | nia | avsoo | = | 00 on 1 | 4 | |||||||
| 1 ME 20v Ax TANT | oa | raseae | os | #20 Onm saw | v | ||||||||
| 330 PF Sov AX ce@ | 718 | 74.8138, | 300 OHM | 1 | R231 | ||||||||
| ve | sme 950 ax taN | as | : | i | 330 OFM 1 | 2 | nieo-nie: | ||||||
| . | SOM’ Scv AX CER. | eo | javtavo | | | tn | " | a | 15a, R227, R40} | |||||
| oma | ‘rome vey ax cer | oe | ragara | aK | ow | 1 | 299 | ||||||
| crya CPaa. | 1 Me Woy AK CEA | 7 an | = | ark | “ | 19 | 101-107, R18S~ 166, R225-226. | ||||||
| crae | Yo ME oSy ax TANT | ae | valine | Reza, A297, n234, R295, R402, RAOS,FEMMAGT | |||||||||
| ras eras | sor wr aey ax cow | oe | se | sek | ow | 2 | v7a-R178, Rx97-R202 | ||||||
| °52.CPS3 | OME 25V AK TANT | wre | — | 2ak | 4 | R78, RIG | |||||||
| < | creas | q | ae! | 2 | B23; nee | ||||||||
| cose | sro. yev ax cuter | ite | wel | = | ron | con) | 7 | le | ate | 8 | fi35,#203-R208,Ra16-R2ID | ||
| P20 rao | fone 26y an ta | a | | | ioe | 2 | Riad nia | |||||||
| uc | yacsaee | 2) | * | eo | * | . | _ laa | eon | 2 | wise, mia | |||
| ae | Foie | | | i | F | ae | ‘ | Brad mes, R149, 9:50 | ||||||
| ater mio? | sar | 17880 8 CARBON | ” | teas | 3 | Pues, | 2 | rs2, Rise | |||||
| ave. nay | WOR | ow ww | +a | " | =] | 1oK 10 FIN SIP | 1 | nwo | |||||
| 90 | “ | ark 10 PN SP | 2 | us | |||||||||
| nuae | wok | ow ww | wal | crm | on | fez} | z | ||||||
| Rina aus | 62K | to | #190 | 7 | ic | 1 | . | z | 47K | 8 PIN SIP | 1 | aves | |
| a | ae | 20 | prow 02 & | ] | | | . | are | 10 Pm SIP | 2 | any, pate | |||
| a | rais8 | as | ae | jar. | las | | | aw | ae | |||||
| nae | tor | ow Hoo | i | ae | i | | ! | wees | ‘ | 0101-0103, 0105-0107 | ||||
| faa. a0 | 620K | rat | Lee | | | esa | icsar | esae | /icsas | tesa | | esag | |||||||
| aed | nnd | me | rare | | | ! | pif | | | ‘ | te 110 | 2 | 0191-0103 | ||
| “8 | oe | cana | nor | ratsoes | g | rats02 | : | °° | |||||
| F155, RISE | 10% | 1 | FaLaret | 7ausos | ’ | cir | |||||||
| F169. RIE | 830 On | 7 7 | in ‘ ava | __. | Tage | i | “ | ||||||
| see | poem 6 | — | = | 407 | 1 | ce | |||||||
| e179, R86 | zax | on | thts | W/OD | > KI | 1426 | 1 | ee | |||||
| sio?- nao | sex | : | ; | vaso | W/O FANNING KIT | aise | ‘ | steer e | |||||
| e0u-Re08 | 33K | . | . | me | PEI | 7416) | i | ||||||
| pop.aee | ax | : | Mes wanenae” | cx pm soon | _ DESIGNATION LIST | CROSS REFERENCE LIST | ise | ' | Be | ||||
| pats | moot | ft | _ | “yeu | ag | “peteuarion | CRITI | SCRIPTION. = WANDITY. | DESIGNATION | PART NO. | were | ! | on |
| oe ae | ae | +0 | pect | fen | SR IPTION | 2 | " | ee | |||||
| nea ene | oe | 8 | vont | form | 403, R404 | SSK L/W SH CHE. | SK 1/4 9°% CRB. | 2 | RA03,RA04 | ——0062-251B3-1XXX | ssi | : | pats. te-800 |
| rr | fy | aie | OPIN CONN. KK-100 (iP) | rausze | 3 | 04. 62, F2 | |||||||
| E26, RERE | * | : | icin | . | rausz4s, | 1 | an | ||||||
| nee? | c« | <I | . | rausa79 | : | a | |||||||
| ad | : | > | 2 | 5 Pi nk 190 AT ANGLE | nausa67 | : | cu | ||||||
| are | . | . | oN ee | racsore | 1 | as | |||||||
| bd | . | : | “ | hem oe | raisero | 2 | eae | ||||||
| aess | . | - | opm | ay-3-8010 | 2 | rery | |||||||
| wene,nens | . | . | . | vem | (wsa00 | : | oa | ||||||
| nase | : | : | sp | ease | 2 | C10, £10 | |||||||
| RBO-R306 | . | - | mc 14018 | a | Or-D9 | ||||||||
| en | = | sea | sowecer wie | cr4oz4 | 1 | owe | |||||||
| ance | : | Leos | YeLow iva | nROM soe-4 | ‘ | bee | |||||||
| Reos-rao7 | RAM 4x8 SUB | \ | se | ||||||||||
| on | sw | v0 position ow | ou stenow 0 | ‘ | oo | ||||||||
| rita mate | sis | . | . | . | s | ' | se | OPTION KIT:UPRIGHT,, MINI | |||||
| My | swe | PUSH SUTTON SW | “ | 2 | , | ae | I, | ||||||
| ald | oe | : | _ | OPTIONKIT: COCKTAILS | |||||||||
| is | TAL? | ye maz crysTaL | 2-80 (3860) | 1 | me | ||||||||
| _ | meet | omar | ‘HIS DRAWING VALID FOR | 16 PIN IC SOCKET | a | vespt2 | |||||||
| “—"iK' @'l! VERSION SOUND (70 | 20eNH ow | s | Iesas-icsato | ||||||||||
| worm | 2 | e8a12, 8F6, 1eSr7 | |||||||||||
| 3. PIN KK=100 RT ANGEL | 1 | a | |||||||||||
| sown | 1 | os | |||||||||||
| 4 PINCONN KK 156 (SIP) | 2 | Pah | |||||||||||
| — | : | 20PIN" | 7 | 2 | vie | ||||||||
| PROUEET EN: CARY MEDAICK | _ | “SOLARFOX] | MIDWAY MFG. ©O. | JUMPER wine | 2 | awh, ame | |||||||
| IT | ~ | as ae a | —— | NAPs | a | Hao! MeQ103 | |||||||
| i | Loam | ASS'Y DRAWING SOUND I/O | |||||||||||
| | | [oe FR | 4, | 8 position ov sw | : | swo | ||||||||
| | | 1 | averee | A082—90908-.000 | MO51-00982-BCC9 | ve PoerToN OW 5M | : | om | ||||||
| ~ | Pe sw. | : | swe | ||||||||||
| ve wnz cavsTALWaRo LEAD | ' | era |
PART NO
9e0-0pa00-o900 0986-90800-2600
0986-00800- 1000 0986-00800-1300 0986-00800-1200 (0886-00800-2600 0986-00800-2000
0980-00800-1 100, 0986-0080n- 400 0986-c0800-0700
0286-00800-2700
0082-06389. 1xxx
(0062-15383 XxX 082-14 183-1x%%
0062- 18983- 13x 0062 19903- 144%
062 22789-1xx% 0962-29283. 124% 062 24568- 1XK 0¢2-2a788. Lxax Soee- 25108 Ix 0962-27588- box 062. 26785. KKK 0062-31383 1xxx 0082-92383: 1xxx
op8¢-00805-0800 0986-00805-0600
0986-c0805-0400 0986-008vs-0300
0986-00802-0500, 0986-00802-0400,
0966-00803-6900
9986-00803-7300 ove¢- 00803-7200 0985-00803-8 100, 0986-0080 6700 ‘098¢-00803-6800 98¢-00803-8500, 0386-00803-51c0 O66 00803-53.0 866-0603 -7560 (2 EO
0886 -00803- 5600
o986-00803-7000, 2480-o0809-4600 986-00203-6200, 0986-00803-n500, 886 00803-4900,
0986-00802-6200 o988-o0803-7100 0986-00803-4200
0982-00803-3500 99782-00808- 3600 ove6-o0809-s500,
opas-cosos- 1600 0986-00804- 1500
2900-16266: 9400 3000-16966-0500
3000-16266: 1800 0886-00806: 098 00804-1200
0986-00804-4000
‘0986-00808- 1009
0986-00508-1 100
9-17