Tee'd Off Service Instruction Manual
Tee'd Off Golf (TECMO) · Instruction Manual · 17 pages · 23 sections · original scan
rom
Service Instruction Manual
Let “Tee’d Off Putt You Into the Green”
TECMO
18010 S. Adria Maru Lane Carson, California 90746 (800) 457-6050 (213) 329-5880
Warning
All control circuits are composed of |C’s, and though they have a long service life, they may be instantly broken in the event of mishandling. So, fully observe the following precautions:
- Besure to turn power"OFF” when changing parts or pulling/inserting each connector.
- Don'tuse the tester to inspect the PC board, since an IC may be broken due to the tester's internal voltage.
- Be sure never to expose the PC board to direct rays of the sun.
4, When connecting the connector, be careful so that it is correctly directed,
- When moving the PC board, use a PVC air mat, bubble wrap, etc. so that the board does not receive a strong shock.
- Players may receive an electrical shock if this game is not properly grounded! To avoid electrical shock, do not plug in the game until it has been inspected and properly grounded. This game should be plugged into only a grounded 3-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electrical shock if the control panel is not properly grounded! After servicing any parts on the panel, check that the grounding clip is firmly secured to the metal tab on the inside of the control panel. Only then should you lock up the game.
Notice
Parts salvaged from your old game are required to complete your kit. These salvaged parts MUST operate perfectly, or the converted game cannot perform properly or safely. Always repair circuitboard malfunctions and cabinet damage before conversion is attempted.
‘STOP’
Read this entire manual before beginning work on this new video conversion! We have carefully included EVERYTHING needed to make this kit more than just a conversion! When finished, this kit should look, play and earn like a brand new, dedicated, video game. We have painstakingly prepared a FIRST-CLASS complete kit. First things first. Using the KIT CONTENTS page of this manual, inventory ALL the parts. Make sure you have tham all! Next, carefully read all the various sections of this manual because it is filled with very IMPORTANT information. We want this new game to earn money for you as much as you do! So please, read through ail ithe sections and proceed ONLY after you fully understand them ail.
Suggested Tools
Electric Screwdriver Wire Cutters Center Punch Electric Dritl Hole Bit (Size 1 3/16”) Soldering Iron Resin Core Solder Pliers Phillips Screwdriver Sand Paper Semi-Gloss Latex Paint Windex (or similar) Squeegie Knife Razor Kit Contents
1 — TECMO Printed Circuit Board 1 — Marquee Plex 9” x 24” 1 — Clear Piexiglass 1 — Control Panel Overlay 1 — Player 1 “START” sticker 1 — Player 2 “START” sticker 1 — Shot Select sticker 2 — Side Decals 1 — Wiring Harness 1 — White Button 2 — Red Buttons 3 — Button Switches 3 — Pal Nuts 1 — Instruction Manual 1 — F.C. sticker
Description of Game
Tee'd Off is a goif kit manufactured by TECMO Inc. forsale in the United States as a vertical corversion kit that allows you to retro-fita Birdie King II” cabinet. Teed Off can also be utilized witha Universal cabinet with additional modifications to the contro! panel, electrical wiring, as further explained in the Cabinet Preparation section of your service manual. Tee'd Off is a terrific new golf game that utilizes a multi-directional trakball which enables the player compiete control of every shot direction. Tee’d Off is a22 hole golf course with many exciting variables that will keep players interest level high and insure your return on investment!
Included Features Tee'd Off golf features includes:
- Vibrant hi-reslolution color graphics. © 22 holes of action-packed golfing fun.
- Multi-directional trakball control.
- Split-screen scanner which allows an overview of each hole to be played.
- Variable shot select button which offers the following types of shots: Straight — Slice — Fade — Draw — Hook 1 & 2 Player select button.
- Variable wind speed and direction. Obstacle Course throughout every hole.
- Shot timer which limits the time between player shois. Extra golf ball awarded if player is under-par.
- Lose golf ball if player is over-par or gives-up.
- Number of golf balls remains constant if player hits par. Continual buy-in feature throughout play.
Wiring Procedure
Installing Interboard Wiring Disconnect the old wiring harness from the CPU board. Using the schematic drawings from your old game, carefully note the function of each wire. Label the wires if this helps. Carefully remove all circuitboards and the metal circuitboard panel from the game. Leave the transformer chassis and the power supply braid in the game. The wiring harness enclosed is made especially for the conversion of a Birdie King II” cabinet into Tee’d Off”. If you are using the Birdie King II" cabinet, leave the existing Birdie King II* har ness intact. Plug the finger board on the Tee’d Off™ harness into the 22 pin double-sided cornector, making sure the polarizing key is aligned with the slot in the finger board. The coin switches, player 1, player 2, speaker and monitor are now connected. The Tee’d Off” harness also plugs into the existing trakball assembly. Disconnect the Birdie King II" connector and piug in the Tee’d Off harness. Next, solder the shot select wires to the shot select button. Now wire the power supply.
Wiring To Power Supply As mentioned in the section POWER REQUIREMENTS, this game uses +5V and +12V DC. Chances are the cabinet you are converting has a properly working power supply that is able to supply these voltages. If not, itis a good idea to install a new, inexpensive ‘switching’ power supply available from your local distributor. Locate the +5V leads color coded RED, and installthem to the proper position on the power supply. Next, locate the +12V leads color coded YELLOW, and install them to the proper position on the power supply as well. Last, position a BLACK ground wire from the harness and connect it. The game is now wired for power.
Ground System Itis highly recommended that a continuous GROUND wire be installed that is connected to every electronic component, such as: shield to, PCB to, power supply to, cain door to, control panel to, etc.
Universal Upright Cabinet If you decide to wire your Tee’d Off kit into a Universal upright cabinet, the following steps are suggested: Leaving several inches of wire from the old wiring harness at each connector, cut the wires near the game's coin door, monitor, player panel, power supply, and speaker. DON'T cut the other side of these same wires (that is, at the CPL-board end). Following the schematic drawings for your kit, solder the coin door, monitor, control panel, power supply and speaker wires to the new CPU-board harness. Using electrical tape, be sure to insulate all splices.
Notice
If you wish to use a coin meter for your Tee’d Off™ kit, you must change the existing Birdie King II" coin meter (+12V) to a +5V coin meter. See the Tee’d Off™ coin control wiring diagram for suggested wiring.
Setting the Dip Switches
Now is a good time to set the Tee’d Off™ dip switches. Refer to the “Dip Switch Placement” and “Dip Switch Settings” included in this manual and adjust the game as desired. The PCB is now ready to install into the cabinet.
Installing the F.C.C. Cage Assembly Using screws, mount the bottom of the F.C.C. cage on one of the inside walls of the cabinet. Next, mount the PCB. Keep in mind the position of the edge connectors. Plug the new wiring harness onto the new CPU board. Support the harness as necessary with plastic wire guides. Make sure the finger board does not touch any metal surface. Nexi, position the F.C.C. cage cover over the Tee’d Off” PCB and secure it with screws to the cabinet. Make certain there are no wires pinched.
Notice
Make sure thai the F.C.C. cage is not mounted near any direct heat sources and is well ventilated.
Thank you for your purchase of a TECMO Inc. Tee’d Off™ kit.
Cabinet Preparation
Cabinet Inspect your old cabinet for any gouges or objects stuck on the extremity such as chewing gum. Remove all foreign objects and fill in the gouges with any type of quick-hardening wood putty. Sand to make sure the surface is smooth and wipe clean the outside of the old cabinet. If the decal of this kit does not cover all of the old games graphics, we recommend repainting the outside of your cabinet with an acrylic based semi-gloss paint. This can be applied by either paint brush, roller or spray can. In games that have woodgrain sides, please remove old decals and clean the surface so there is no glue residue remaining on the cabinet. To apply your new side graphics take a straight edge and make a top guideline roughly where the old graphic started on your game. Lightly moisten the cabinet with spray window cleaner and begin to apply the decal starting at the top working your way to the bottom. After the decal is in place, use a piece of the foam strip that comes in the packing as a squeegee and smooth the sticker down on the surface to remove excess moisture. Please allow 12 hours for your sticker to become permanently adhered to the sides before use.
Marquee Plex Enclosed in this kit you will find one universal size Marqee underlay and a clear plexiglass sheet. These should be ideal for the cabinet you are converting. Using the old margee from the previous game, lay it on top of the new one. Be sure that none of thetitle“Tee’d Off” is excluded before marking it to the proper size. Once this is done, proceed to cut it. Unless you have the equipment to cut the plexiglass safely, we recommend taking it to a local plastics supply to do the job. They usually charge no more than a couple of dollars, and you can insure it will be done right and without breakage. After the plexi is cut, install it! Now is also a good time to inspect the lighting system. If the bulb(s) is old, replace it! This will insure a ‘shining’ and bright advertisement to lure paying customers to your newest game.
Control Panel From the control panel previously removed, take off the old buttons, switches, trakball, and wiring. Strip off the older lexan overlay and any vinyl button stickers. Using sandpaper, prepare the control panel surface until all remains of the previous material are gone. Lacquer thinner may be necessary if glue is still present. Clean the surface with soapy water, and then thoroughly rinse it. Dry the control panel completely! Use the CONTROL PANEL TEMPLATE included in this kit. Lay iton the control panel centering at the trakball location. Leave your existing 1 or2 player start button holes where they are. Mark the necessary holes, then drill as needed. We suggest plugging any hole that is no longer needed with wood blocks, putty, cardboard or epoxy. Remove the backing from the rear and carefully place the control panel overlay over the control panel, being careful not to get any air bubbles in the viny! when it’s applied. After the control panel is securely on, with an exacto knife or razor blade carefully cut out holes on the contro! panel. Next install the button stickers on the contro! panel in their proper locations. Replace the buttons on the control panel and tighten them down. Return the control pane! to the game for the next step in the kit process.
Notice
Refer to the contro} panel layout for suggested placement of button switches and control trakball. Make sure that the control panel is on straight.
Control Panel Layout
1%” DIAMETER
1 PLAYER 2 PLAYER
SHOT SELECT
2%4” DIAMETER
Dip Switch Settings
e Position of Dip SW
Dip Swi ON
© Setting for Dip SW ol ol ON Dip SW3. or? IN D FF ip Sw2 Sound volume
1 2 3 4 5 6 7 8
Dip SW1 Unused Dip sw2 eoniced Cabinet | Demo
Coin 1 Coin2 Unused Type Sound
Initial Number A
Dip SW3 of Balls Ball Extend eee Difficulty
© Dip SW(2)
[ swl 1|2]3! 4 Coin/Credit 1Coin-1Play | off| off 2Coin-1 Play | On| Off 1 Coin-2 Play | off| On 1Coin-3Piay | On| On 1 Coin- 1 Play ott | oft 2 Coin-1 Play On| of 1 Coin - 2 Play off | On 1 Coin- 3 Play On| On|
swis |e Unused Unused ott | off
sw 7 Type of Cabinet Cocktail off
Upright On
sw 68 Demonstration Sound Demo Sound Off No Sound On |
¢ Dip SW(3) swi1]2]3 Initial Number
| 3 | Ott } off | Off | ef Balls |
4 On | Off | Off
| 5 | ott} | On | Off | |
6 On | On | off 7 Off | Off | On 8 On | Off | On
Ball Extend sw) 4 | 5 Option 2 (Moderate) | Off | Off 1 (Easy) | On| Off 3 (Difficult) _| Of | On 4 (More Difficult) | On | On
Option Number 2 1 3 4 Scoring for Ball
| 7 Gooey | \ | 1 | , | 2 | Extend Option |
| +2 (Double Bogey) | 2 | 1 | 2 | 3 | | |
| +3 (Triple Bogey) | 2 | 2 | 3 | 4 | |
| +4 | 3 | 3 | 4 | 4 | |
| Give Up | 4 | 4 | 4 | 4 |
SW) 6 Sub-Par Off Sub-Par+1 On
SW| 7 8 2 (Moderate) | Off| Off 1 (Easy) | On| Off 3 (Difficult) | Off} On 4 (More Difficulty | On} On Additional Balls for Sub-Par Play
Difficulty: Stength of Wind Direction of Wind Number of Trees
Display Check
After turning the power on, the follwing display check should be viewed. The display shows for4 seconds. Push the shot select button for continued viewing.
ROM 1 CK ROM 2 CK ROM/RAM ROM 3 CK 2P DOO Control Ball Check BoM al ck pee Check RAM CK 123 45 67 8
Color Check
DIP SWITCH Dip Switch 4 Check
Dip Switch Check Check the dip switch settings. Adjust as desired. (Push the shot select button once more and the screen will change to a cross hatch.)
ROM/RAM Check Ifa ROM or RAM fails, “ERROR” will be displayed. If this occurs, it must be replaced.
Control Ball Check
Spin the trakball to check both “Direction” (left, right, up, down) and “Revolution”.
Cross Hatch Check
The cross hatch check will be displayed for 4 seconds. Push the shot select button for con tinued viewing. Push one more time for game demonstration.
Wiring Diagram
J2_ Kel i150N-036-009 TWBlue 2}8 3 fe
| TWGreen | mm . | ats : | Tie |
| TVRed | 1 | sts | me aa |
| Bk | Cc | -Blue | |
| GND | a 7 | Wor] | Tv-Sync |
| L. | w | D | |
| Tene | _ | = | Sound (H |
72 | Sound (-)
| 13 | —— | Key Slot |
rr 15 7
| 16 | Pr H | Br Brown | |
| 7 | 8 | Coin ta | R Red |
| 18 | I | i} Orange | |
| 19 | a | ¥ Yellow | |
| 20 | K | B Blue | |
| 2a | 10 | Pr Purple | |
| 2B. | u | ] Ww White | |
| 23 | 1 | Bk Black | |
| 2a! | _ M | WIR | _ White/Red | |
| 25 i | wR Le | 1 Play Start | ic} Green |
26 wR | N 2 Play Start 27 3
| I | 28 | i |
29 14 30| R at 16 32 3
- 16 34 T 35 7 36 u Ji Kel 1150N-036-009 By
Ww
x
| GND | 7 ot 1 | 2 |
| GND. | 2 | ¥ |
| GND. | 3 Bk | 22 |
a Z TeV B R
| +5V. | 7 6 | Bik GND |
a8
| au | st ely | Red sy To Power |
| Hav | Toy | Yellow yoy Supply |
Sound) TH G ‘Sound (+) 12 |-Y Contror-Ball SG2 is 7 Control-Ball SGt i. Control-Ball SG4 15 2 Bk
| ControF Ball SG | 16 | aa | GND |
| 17 | a2 | +5 |
18 Kis Contiol- Ball SG2 79 4 Contror Ball SGI 20 Es Contro-Ball SGS
| 24 | 6 Control-Ball SG4 | To Control |
| L | y EH | Panel |
2a 2 Play Start 25 WR ot Shot Select 7 Play Start 26 | Br Shot Select 28 2 Coin In 30; il
Tee’d Off
Coin Control
+5V FROM POWER SUPPLY
COIN METER (COUNTER)
EDGE CONNECTOR
PIN 30
JZ CONNECTOR
TO PCB SIGNAL {NPUT COIN aT ES PARALLEL
SERVICE SWITCH
Notes
Notes
Power Requirements
The TECMO printed circuit board included in this kit requires +5 voltage and +12 voltage. The +5 voltage should be exactly 5V for this P.C.B.5.2V is OK, but use no higher than this and not lower than 5.0V. This should be rated at 5 amps. +12V should be rated at 1 amp.
Monitor Requirements
This TECMO printed circuit board requires interfacing with NEG () composite sync. Most monitors have provisions for composite sync. Some monitors require that the vertical and horizontal negative sync be tied together in order to achieve a composite signal. For best results consult the monitor manufacturer or the distributor service department where this kit was purchased.
Service Information
TECMO, INC. guarantees this product to be free of defects for a period of 30 days after purchase. TECMO will repair or replace this product upon our inspection. Proof-of- Purchase may also be required. If you have any questions, please call our out-of-state WATS number at 1 (800) 457-6050. Or write to: TECMO, Inc., 18010 South Adria Maru Lane, Carson, CA 90746