CATHODE RAY TOMES

Star Gaurds UR to Rampage UR Field Conversion Kit Instructions (M051-00F06-A010)

Star Guards U.R. to Rampage U.R. (Bally Midway MFG. CO.) · Kit Instructions · 38 pages · 10 sections · original scan

Page 1

STAR GUARDS UR. — TO RAMPAGE U.R.

Field Conversion Kit Instructions

Bally MIDWAY MFG. CO. 10601 W Belmont Avenue Franklin Park. tHlinois 60131 U.S.A. Phone (312) 451-9200 Cable Address MIDCO Telex No. 72-1596

MO5 1-00FO6-A010

Page 2
WARNING

THIS GAME MUST BE GROUNDED. FAILURE TO DO SO MAY RESULT IN DESTRUCTION TO ELECTRONIC COMPONENTS.

WARNING: This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has not been tested and found to comply with the limits fora CLASS A computing device pursuant to SUBPART J of PART 15 of FCC RULES, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.

ELECTRICAL BULLETIN: FOR ALL APPARATUS COVERED BY THE CANADIAN STANDARDS ASSOCIATION (CSA) STANDARD C22.2 NO. 1, WHICH EMPLOYS A SUPPLY CORD TERMINATED WITH A POLARIZED 2-PRONG ATTACHMENT PLUG.

CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

ATTENTION: POUR PREVENIR CHOCS ELECTRIQUES NE PAS UTILISER CETTE FICHE POLARISEE AVEC UN PROLONGATEUR. UNE PRISE DE COURANT OU UNE AUTRE SORTIE DE COURANT, SAUF SI LES LAMES PEUVENT ETRE INSEREES A FOND SANS EN LAISSER AUCUNE PARTIE A DECOUVERT.

Bally MIDWAY

OUR TOLL FREE NUMBER FOR SERVICE INFORMATION CONCERNING THIS GAME, OR ANY OTHER BALLY/MIDWAY™ GAME YOU NOW HAVE ON LOCATION.

CALL US FOR PROMPT, COURTEOUS

ANSWERS TO YOUR PROBLEMS.

Video or Pinball - Continental U.S. 800-323-7182

Cally MIDWAY 10601 West Belmont Avenue Franklin Park, illinois, 60131 phone (312) 451-9200

©COPYRIGHT MCMLXXXVIt BY BALLY MIOWAY MFG. CO. ALL RIGHTS RESERVED.

NO PART OF THIS PUBLICATION MAY BE REPRODUCED BY ANY MECHANICAL, PHOTOGRAPHIC, OR ELECTRONIC PROCESS, OR IN THE FORM OF APHONOGRAPHIC RECORDING, NOR MAY IT BE TRANSMITTED, OR OTHERWISE COPIED FOR PUBLIC OR PRIVATE USE, WITHOUT PERMISSION FROM THE PUBLISHER. THIS MANUAL IS FOR SERVICE USE ONLY, AND NOT FOR GENERAL DISTRIBUTION. FOR PERMISSION REQUESTS, WRITE: BALLY MIDWAY MFG. CO., 10601 W. BELMONT AVE., FRANKLIN PARK, IL 60131. .

Printed in U.S.A.

Page 3
WARNING

The parts contained in this field conversion kit must be installed without deviation from the instructions contained in this manual and kit. Failure to follow these instructions in every detail may result in the creation of illegal interference to radio and TV reception.

BALLY MIDWAY has verified that this field conversion kit, when installed in the game(s) specified in this manual, complies with the requirements in Part 15 of the FCC rules for a Class A computing device. Operation of this equipment in a residential area may cause unacceptable interference to radio and TV reception, requiring the operator to take whatever steps are necessary to correct the interference.

BALLY MIDWAY will not be responsible for incomplete or improper conversions, or installation in a game for which this field conversion kit is not intended. If this field conversion kit is installed in a game that is not specified in this manual or in a previously converted game, the operator is required to take whatever steps are necessary to insure compliance with the requirements in Part 15, subpart J, of the FCC rules for a Class A computing device.

SPECIAL NOTE:

DO NOT DISCARD ANY OF THE PARTS YOU REMOVE WHEN MAKING THE MODIFICATIONS EXPLAINED IN THIS MANUAL.

THEY WILL BE RE-USED IN FUTURE CONVERSION KIT!

Page 4

SAFETY

The following safety hints apply to all game operators and service personnel. Specific warnings and cautions will be found throughout this manual where they apply.

WARN INGS

AC POWER CONNECTION. Before connecting the game to the AC power source, verify that the proper voltage-selection plug is installed on the game's power supply and the electronic chassis assembly.

PROPERLY GROUND THE GAME. Customers may receive an electrical shock if this game is not properly grounded! Sente games should only be plugged into a grounded 3-wire outlet. Customers may receive an electrical shock if the control panel is not properly grounded! After servicing any parts on the panel. Check that the grounded wires are secure. Only then should you lock up the game.

DISCONNECT POWER DURING REPAIRS. To avoid electrical shock, disconnect the game from the AC power source before removing or repairing any part of the game. When removing or repairing the monitor, extra precautions must be taken to avoid electrical shock because high voltages may exist within the display circuitry and cathode ray tube (CRT) even after power has been disconnected. Do not touch internal parts of the display with your hands or metal objects! Always discharge the second anode from the CRT before servicing this area of the game. To discharge the CRT: attach one end of a large, well-insulated, 20-KV jumper to ground. Momentarily touch the free end of the grounded jumper to the anode by sliding it under the anode cap. Wait two minutes and discharge the anode again.

USE THE PROPER FUSES. To avoid electrical shock, use replacement fuses which are specified.in the parts list for this game. Replacement fuses must match those replaced’ in fuse type, voltage rating, and current rating. In addition, the fuse cover must be in place during game operation.

HANDLE FLUORESCENT TUBE AND CRT WITH CARE. If you drop a fluorescent tube or CRT and it breaks, it may implode! Shattered glass can fly eight feet or more from the implosion.

CAUTION

PROPERLY ATTACH ALL CONNECTORS. Make sure that the connectors on each printedcircuit board (PCB) are properly plugged in. If they do not slip on easily, do not force them. A reversed connector may damage your game and void the warranty.

Page 5

STAR GUARDS U.R. TO RAMPAGE U.R. CONVERSION PROCEDURE

The STAR GUARDS U.R. to RAMPAGE U.R. Conversion Kit has been designed to be installed in your game cabinet with a minimum of effort. The only tools needed are: a1/4" nut-driver, a device for removing I.C. chips, and a special wrench (which you received with your STAR GUARDS U.R. game) for removing tork tamperresistant screws. Please read the following instructions thoroughly before you begin.

NOTE: Included in your conversion kit is a RAMPAGE U.R. Game Manual (Part No. 0£36-00300-0000) which provides you with complete game information, however, disregard information on pages 1-6, pages 2-11 through 2-14, and also pages 3-2 through 3-16. Refer instead to pages 6 & 14 through 34 in this conversion kit instruction manual.

REMOVAL OF OLD GAME HARDWARE

  • Turn the power off to your game and disconnect it from its wall outlet.
  • Unlock and open the cabinet's Coin Door.
  • Unlock and remove the Rear Access Door.
  • Using the special wrench (for removing tork tamper-resistant screws), remove the retaining bracket at the top of the cabinet. Slide the header glass up and remove (and discard) the Header Attract Art.
  • Release and unhook the two latch clamps of the Control Panel. Swing open the Control Panel on its hinge. Disconnect the Control Panel's cabling from the Master Cable. Also, remove the Control Panel's ground strap from the Control Panel. Remove the five wood screws holding the Control Panel's hinge to the cabinet, lift the Control Panel out and discard it.
  • Remove the Test Bracket of the Master Cable and Test Bracket Assembly (from the inside cabinet wall on the left side of the Coin Door) by removing two wood screws.
  • Remove the Master Cable and Test Bracket Assembly by removing it's connector plugs from all of the P.C. boards and the POWER CHASSIS ASSEMBLY. Please note that the new Master Cable and Test Bracket Assembly will be routed as the old cabling was. Therefore, leave all cable clamps where they are in the cabinet.
  • Remove and discard the 8 TO 4 MULTIPLEXER P.C. BOARD. Also, remove and discard the LAMP CONTROL P.C. BOARD. Neither board will be used for the RAMPAGE U.R. game.
  • Remove the yellow ground strap of the CARDRACK W/MONOBOARD ASSEMBLY, and the yellow ground strap of the CARDRACK W/SOUNDS GOOD BOARD ASSEMBLY from where it is fastened to the POWER CHASSIS ASSEMBLY.
Page 6

REMOVAL OF OLD GAME HARDWARE, CONT'D.

10.

ll. Remove the CARDRACK W/MONOBOARD -ASSEMBLY by loosening two wood screws holding the Cardrack's brackets to the cabinet's Coin Box Compartment wall. By lifting the assembly up and away from the cabinet wall, remove it from the cabinet and set it aside.

Remove the CARDRACK W/SOUNDS GOOD BOARD ASSEMBLY by loosening two wood screws holding the Cardrack's brackets to the inside of the cabinet's left side wall. By moving the assembly towards you and away from the cabinet wall, remove it from the cabinet and set it aside.

Page 7

REPLACEMENT OF PROGRAMMED GAME 1.C.‘S , |

1.. Remove the eight EPROMS located on the MONOBOARD as shown in Figure 1 and discard them. Replace the removed EPROMS with the ones supplied in your conversion kit. They are installed as shown in Figure 1. Also cut jumper JW2. : : :

NOTE: ROM/EPROM List information (on the inside: back cover of the RAMPAGE U.R. game manual included in your kit) regarding the unprogrammed Monoboard also applies to A084-91787-F000.

REMOVE (8) EPROMS. AND REINSERT NEW EPROMS SUPPLIED WITH KIT, CUT JUMPER JW2 {LOCATIONS 15A, 38, 58, 14B, 4, 5E, GE & 8E)

ial

  • i or, 40 tS Ths @s: ‘=i a cE cs Pace-3) = cil om a Bast Peres} a a I Sear pe Bono oe es Pe oe 1S am ™ ao = =| i = = a

i

i

= s eugeuw gag iE

=r =) Sem TENT

pgraege2esszee2 | egeoron

IMPORTANT!
NOTE LOCATION OF NOTCH ON ALL I.C.'s REMOVED BEFORE INSERTING.

Figure 1

Page 8

REPLACEMENT OF PROGRAMMED GAME I.C.‘S, CONT'D.

2. Remove the four EPROMS located on the SOUNDS GOOD P.C. BOARD as shown in Figure .2 and discard them. Replace the removed EPROMS with the ones supplied in your conversion ‘kit. They are installed as shown in Figure 2.

REMOVE (4) EPROMS AND REINSERT NEW EPROMS SUPPLIED WITH KIT. (LOCATIONS U7, U8, U17 & U18)

TUPPTE EET TT

'A080-91863-8000 SOUNDS GOOD.

IMPORTANT f
NOTE LOCATION OF NOTCH ON ALL 1.C.’s REMOVED- BEFORE INSERTING.

Figure 2

Page 9

INSTALLATION OF NEW GAME HARDWARE

1. Reinstall the CARDRACK W/SOUNDS BOARD ASSEMBLY in its original position inside the cabinet.

Reinstall ‘the CARDRACK W/MONOBOARD ASSEMBLY in. its original position inside the cabinet.

Secure the existing yellow ground strap of the CARDRACK W/MONOBOARD ASSEMBLY and the existing yellow ground strap of the CARDRACK W/SOUNDS GOOD BOARD ASSEMBLY to the POWER CHASSIS ASSEMBLY using the hex nut previously removed.

Install the new Master Cable Assembly in the existing cable clamps routing it the way the old Master Cable Assembly was. Refer to the RAMPAGE U.R. Wiring Diagram *(on page 3-25 of the RAMPAGE U.R. game manual included in your kit) for securing the new Master Cable Assembly connectors to the connectors of the existing Monoboard, SOUNDS GOOD P.C. BOARD, DUAL POWER AMP P.C. BOARD and the POWER CHASSIS.

Install the Test Bracket of the new Master Cable and Test Bracket Assembly on the left side of the Coin Door on the inside cabinet wall using the two existing wood screws previously removed.

Secure the new Control Panel, by its hinge, to the cabinet by using the five existing wood screws previously removed. Secure the existing ground strap to the new Control Panel. Refer to the Rampage Wiring Diagram (on page 3-25 of the RAMPAGE U.R. game manual included in your

kit) for securing the new Control? Panel's cabling to that of the new

Master Cable and Test Bracket Assembly.

Close and latch the new Control Panel.

Place the new Header Attract Art behind the existing header glass and slide them into place at the top of the cabinet, using the special wrench (for. installing tork tamper-resistant screws}, secure the existing retaining bracket to the top of the cabinet using the five screws previously removed.

Refer to page 1-6 of your new RAMPAGE U.R. game manual included in your kit and reset the dip switch positions of switch SW2 on the MONOBOARD.

*NOTE: The Wiring Diagram in the RAMPAGE U.R. Manual on page 3-25 contains an error. “CHEAP SQUEAK DELUXE A080-91671-C000" should read “SOUNDS GOOD A080-91863-B000". In the new Master Cable & Test Bracket Assembly the COIN CHUTE 3 switch is wired in parallel with the COIN CHUTE 2 switch.Therefore, the Coin/Credit game options for COIN CHUTE 2 (shown on page 6 in the conversion kit instruction manual) are the same for COIN CHUTE 3.

-5~

Page 10

INSTALLATION OF NEW GAME HARDWARE, CONT!D.

  • Replace and lock the rear access door.
  • Replace and lock the Coin Door.
  • Secure the cabinet's line card plug to its power outlet and turn the power on.
  • Run the game through its self-test procedure. Refer to page 1-5 of your new RAMPAGE U.R. game manual included in your kit for self-test information.

RAMPAGE JU. R.

OPTION SWITCH SETTINGS

TUITIITTTTTTTAT TLL SMYTH NO. 2 - AT AL3 - LOCATED ON MONOBOARD ////////////////////11 DURING GAME PLAY: SW#1 SWH2 SW#3 SW#4 SWHS SW#6 SWE7 SW#8 a ‘SWHID

DIFFICULTY LEVEL 1-NORMAL | OFF OFF DIFFICULTY LEVEL O-EASY ON OFF DIFFICULTY LEVEL 2-ADVANCED “se scoRE OPTION- ON =| st—<“‘é—CSOSO™””””C™! SCORE OPTION - OFF

OIN CHUTE 1:

1 COIN / 1 CREDIT COINS/ 1 CREDIT

CHUTE 2: 1 COIN / 1 CREDIT 1 COIN / 2 CREDITS. 1 COIN / 3 CREDITS 1 COIN / 4 CREDITS 1 COIN / 5 CREDITS 1 COIN / 6 CREDITS 2 COINS/ 1 CREDIT COINS/ 1 CREDIT

** RACK ADVANCE

NORMAL VIDEO FREEZE VIDEO

*® ALLOWS PLAYER TO RETAIN POINT TOTAL WHEN HE “BUYS BACK IN" WITHIN A FIXED TIME LIMIT.

** SERVICE BUTTON ADVANCES RACK

PART NO. M051-00£36-C007 FACTORY SETTING - ALL LOGIC SWITCHES SET IN THE “OFF™ POSITION

Page 11

RAMPAGE/STAR GUARDS FIELD KIT - PARTS LIST PART NO: GF06-00001-0000

ORDER BY PART NUMBER ONLY

PART NO. . DESCRIPTION

AE36-00004-0000 |CONTROL SHELF ASSY.: RAMPAGE (INCLUDES ITEMS 1 THRU 10)

AE36-00005-0000 |CONTROL SHELF CABLE ASSY.

AE36-00010-OOXF |CONTROL-APRON WELD ASSY.

0E36-00501-0000 |CONTROL SHELF: RAMPAGE (WOOD)

0017-00009-0645 |JOYSTICK ASSY.: SHAFT W/BALL (3 REQ‘D.)

0E36-00104-O0XF | PLATE: CONTROL-MTG.

0£36-00106-0000 |STRIKE: CONTROL SHELF (2 REQ'D.)

0E36-00903-O0XF |OVERLAY: RAMPAGE

0017 -00032-0093 |SWITCH: WHITE W/HOLDER (6 REQ‘D.)

0017-00042-0300 |BUTTON: PUSH, ROUND, WHITE (3 REQ'D.)

0017-00042-0304 |BUTTON: PUSH, ROUND, RED (3 REQ'D.)

AF06-00006-0000 |MASTER CABLE W/BRKT. ASSY. (INCLUDES ITEMS 2 & 3) | 11 AFO6-00007-0000 |MASTER CABLE ASSY. 12 A515-00021-0000 )MULTI-FUNCTION SWITCH W/BRKT.: 1-POT (INCLUDES FOLLOWING 6 ITEMS)

0017-00032-0007 |SWITCH: SPDT SLIDE 4 AMP

0515-00107-0000 |BRKT.: SWITCH; TEST, VOLUME, CREDIT

BUTTON: SWITCH, RED

NUT: 3/8" X 32 HEX 0017-00032-0051

WASHER: .375" I.D., .562" 0.D., & .018" TH.

POT: O-1K CBN 1/2W

HEADER: SCREENED

VIEWING GLASS

EPROM: 27128-25 RAMPAGE POSITION 15A

EPROM: 27128-25 RAMPAGE POSITION 148

Page 12

RAMPAGE /STAR GUARDS FIELD KIT - PARTS LIST, conT'o. . PART NO. G06-00001-0000

ORDER BY PART NUMBER ONLY

ITEM PART NO. . DESCRIPTION 17 £36C-47AAE-AX4D. |EPROM: .27256-25 -RAMPAGE POSITION 38

18 £36C-47AAE-BX4D |EPROM: 27256-25 RAMPAGE POSITION 5B

19 E36A-81AAE-AXFD |EPROM: 27512-25 RAMPAGE POSITION 8E

20 E36A-81AAE-BXFD |EPROM: 27512-25 RAMPAGE POSITION 6E

E36A-81AAE-CXFD |EPROM: 27512-25 RAMPAGE POSITION SE al

22 E36A-81AAE-DXFD |EPROM: 27512-25 RAMPAGE POSITION 4€

E36C-47AAE-CX4D JEPROM: 27256-25 RAMPAGE POSITION U17 OR

E36C-47AAE-CXFD |EPROM: 27256-25 RAMPAGE POSITION U17

24 E36C-47AAE-DX4D |EPROM: 27256-25 RAMPAGE POSITION U7 OR

E36C-47AAE-DXFD |EPROM: 27256-25 RAMPAGE POSITION U7

E36C-47AAE-EX4D |EPROM: 27256-25 RAMPAGE POSITION U18 OR

E36C-47AAE-EXFD |EPROM: 27256-25 RAMPAGE POSITION U18 ° Jt E36C-47AAE-FX4D |EPROM: 27256-25 RAMPAGE POSITION U8 OR

E36C-47AAE-FXFD |EPROM: 27256-25 RAMPAGE POSITION U8

AF06-00300-0000 |CATALOG & BAG ASSY. (INCLUDES ITEMS 27 THRU 29)

MO51-O0E£36-A007 | TAG: OPTION SWITCH SETTINGS

MO51-O0FO6-A010 | INSTRUCTION: RAMPAGE /STAR GUARDS FIELD KIT

0£36-00300-0000 |CATALOG: RAMPAGE

Page 13

COIN DOOR W/CABLE: BLACK 3-CHUTE PART. NO. A982-00014-0021

FRONT VIEW

3 NOT SHOWN

Page 14

COIN DOOR W/CABLE: BLACK 3-CHUTE PART NO. A982-00014-0021 :

TOP VIEW

BOTTOM VIEW % NOT SHOWN

Page 15

COIN DOOR W/CABLE: BLACK 3-CHUTE ~ PARTS LIST PART NO. A982-00014-0021 | ORDER FROM COIN MECHANISM BY PART NUMBER ONLY (312) 279-9150

DESCRIPTION PART NO.

BS+X573-1 LARGE DOOR: 3 SLOT

COIN. RETURN CUP DOOR (3 REQ'D.) BS-8000-12

BS-8000-7 COIN RETURN CUP BEZEL (3 REQ'D.) BS-8000-6 COIN ENTRY CASTING (3 REQ'D.)

8000-8 COIN INSERT PLATE (3 REQ'D.)

7800-6 DENOMINATION INSERT (3 REQ'D.)

7800-37 REJECT BUTTON RETURN SPRING (3 REQ'D.)

"C" WASHER (3 REQ'D.) | 9 | 7800-11-ReD | REJECT BUTTON - RED | 10 | a7eo-12-reo | REJECT BUTTON HOUSING (RED)

REJECT BUTTON HOUSING (AMBER)

7800-11-BLUE [REJECT BUTTON - BLUE

REJECT BUTTON HOUSING (BLUE) REJECT BUTTON - AMBER

WASHER 3/8 0.D. (3 REQ'D.)

12V WEDGE LAMP (3 REQ'D.)

WEDGE LAMP SOCKET (3 REQ'D.)

HOUSING RETAINING BRKT. (3 REQ'D.)

COIN ENTRY CHUTE (3 REQ'D.)

"C" WASHER (3 REQ'D.) 20 3300-34

8000-21 REJECT LEVER ASSY. (3 REQ'D.)

Page 16

COIN DOOR W/CABLE: BLACK 3-CHUTE - PARTS LIST, CONT'D. . PART NO. A982-00014-0021 ORDER FROM COIN MECHANISM BY PART NUMBER ONLY (312) 279-9150

DESCRIPTION

4-40 HEX NUT (6 REQ'D.)

8000-10 MECH. MTG. BRACKET "STAKED" (3 REQ'D.)

SW. CHUTE (SMALL) (3 REQ'D.)

7300-134

7300-100-1 BLUE, SWITCH (3 REQ'D.)

5¢ / 25¢ / SW. WIRE (3 REQ'D.)

4-4 X 1" ROUND HEAD MACHINE SCREW (6 REQ'D.) SWITCH INSULATOR (3 REQ'D.)

SWITCH COVER (3 REQ'D.)

COIN RETURN CUP (3 REQ'D.)

SLAM SWITCH BRACKET

SLAM SWITCH

4-36 X 3/8 ROUND HEAD MACHINE SCREW (3 REQ'D.) 7800-42

38 100-4-6

39 8800-24 DBL. BTD. LOCK & KEY W/NUTS ic X615 LOCKING CAM KEY HOOK 41 7800-7

42 * | 0017-00007-0019 |KEY HOOK

A030-00089-0000 {COIN METER ASSY. W/DIODE

A982-00015-0011 |COIN DOOR CABLE ASSY.

48 * | 0017-00104-0019 |WASHER: 6 145 - .375 - 032 FLAT ST. — ; Ps | NOT PART OF ABOVE ASSEMBLY & MUST BE Pf ORDERED SEPARATELY, THROUGH BALLY MIDWAY MFG. CO.

Page 17

NEW MONITOR INFORMATION & NEW COMPONENT LAYOUT AND SCHEMATIC INFORMATION

Page 18

i

{ TYPICAL OSCILLOSCOPE WAVEFORM PATTERNS

The wavetorms shown below were observed on a wide band oscilloscope. The input signal was from a crosshatch generator with a horizomal syne frequency of 15.73kHz and a vertical frequency of 60 Hz. If the waveforms are observed on- an oscilloscope with a limited high freauency response, the corners of the pulses will tend to be more rounded than those shawn. and the amplitude of any high frequency pulse will tend to be less. Each photograph is numbered, These numbers correspond to the circled numbers on the schematic diagrams. Photographs 12. 13, 14, 15 and 16 are of the red signal at various points along the red video channel, The waveforms at cortesponding points along the green and blue video channels will iaok similar

2WOIV2 uSEC/DIV2vIDIV.10 wSEC/OIVO.SV/DIV20 uSEC/DIVO2v/0lvSMSEC/OIV
\Ov/DIVSMSECIOIV2IOIV.2 uSEC/OWVIv/Ow20 vSEC/OINOSV/OIV10 uSEC/OIV
2OV/OW20 uSEC/OIVOSV/DIV20 uSECIOIVSVDIV.20 uSEC/OWIV/OWWO.2MSEC/OIV

14,

IV/DIV. —O.2MSEC/DIV

1v/0Iv.O-2MSEC/OIV2v/DV8.2MSEC/DIVIvralv—-O.2MSEC/OW
  • The troubleshooting chart mentions specifi entire circuit associated with these Components be checked. 2 This chart is a guide to servicing father than a complete list of each component thal could fail, Therefore, troubleshooting should Nt be limited only to those components mentioned in the chart.
  • It is always useful to begin checking a circuit by measuring the DC voltages and then comparing the measurements to those listed in the Typical DC Voltages chart

4, The cutoft controls and drive controls an the neck board and the screen contro! at the bottom of the flyback transformer have bees Preset at the factory When servicing the monitor for a lack of video, do not adjust any of these Controls uniess it is suspected that the problem is a result of these controls having been tampered with. Otherwise do not adjust these controls; if they are so severely out of adjustment that there is a lack of video, then there is something mattunctioning.

  • The Wells Gardner Service Department does accept telephone calls for servicing assistance. Call 1-312-252-6220, between 7:00am 4nd 3:30pm Central Time. Ask for the Service Department The Service Department is closed duing the first two weeks of. July Telephoneassistanceis not available during this period. Before calling. be sure to have available the model number of the monitor being a TROUBLESHOOTING CHART

NG eal VOLTAGE: HECK 8-2 —_ eae | ote nee eneeene 0 3 eur ORO, F202, PINS eS

(cHeck PULSE ATIC. Leia ease SHORTER | CONDITION sce]

(QUIPUT TRANSISTORS + LeepIns'. Lan ronexaune |

IF FUSE IS OPEN, CHECK FOR SHOATED HOR OUT | [UsinG vaniAC. DECREASE AC INPUT CHECK ALONG VIDEO cack | an CHANNEL FROM VIDED ‘ INPUT AT PTO MIDEO | t CHECK FUSE: XO ZERO. THEN SLOWLY INCREASE Sup neangs ton oe ene ‘CHECK FOR GATE PULSE OUTPUT | FROM 2. PIN 12

arcu

REFER 10 SYNC PROBLEMS CHART. ‘CHECK FOR OPEN HORIZONTAL YOKE i, 5, SES Sane

‘CHECK WHETHER HOR. OS- CRLATOR IS OPERATING. CHECK WAVEFORM ® ANO 16 2 PINS 1.2.24 AND (6. bisieceL) ‘CHECK RETRACE TUNING CAPA

HV HOLD DOWN CIRCUIT (S PREVENTING MON TOR OPERATION AT NORMAL AC INPUT, CHECK FOR| FAULTY CONOITION CAUSING HV. TO BE TOO HIGH. EXAMPLE: C36 DECREASED IN VALUE ——J ———E CHECK HV HOLD COW CIRCUIT, DIO, O12, 1C2

Y

NOVERT SYNEROWOR sme]VERTICAL SWEEP-PROBLEMS:
HOR, SYNC OKL VERT. SYNC OKwoSEE NOTES9%

—— A Rance : Sani TaN ne08 eh [eee

orSer une atOrite vest. ped SevEa

Y CENTER OF CRT. (CAL SWEEP. pee | cea cree nin SKE 1 i

—Y(ereexron oraiuen[o.
CHECKeneck |CALYOKE WINDINGS ORen

ee ie 7 cenmieaL YORE aT | CuEGK VERTICAL OSCR croc vec.

ATOR AN Tob =|creek FORSem maTca]_focascans)_[oreoevernca |
caprere. nanoSECIZ PRS 24N0 3POSMON CxA.08 [**) CAPACOR Pat Bey Crick

components to be checked. It is intended that the

serviced and the schematic diagr™m of the monitor being serviced. TROUBLESHOOTING NOTES

Central Time.

slowly withdraw for a distance of 6 feet before turning off.

  • Horizontal vs. Vertical:

along the short dimension of the tube in ai models.

it refers to the short dimension of the picture tu long dimension of the picture tube.

  • Replacement parts may be ordered from the Service Department between 7:00am and 4:30pm,
  • A monitors are equipped with automatic degaussing coils which demagnetize the picture tube everytime the monitoris tuned onafter being off fora minimum of 20 minutes. Should any partof the chassis become magnetized it will be necessary to degauss the affected area witha manual degaussing coil. Move the coil slowly around the CRT face area and all surrounding metal parts. Then

‘Some models have the picture tube mounted vertically rather than horizontally That is, the picture tube is mounted in the frame such that the ‘ong dimension ct the tube is up and down. Examples Of this include (but are not limited to) Models 13K7851 and 19K7951. Other than the physical conentation of the picture tube, there is no electrical difference between these models and their horizontal counterparts. The same circuits, the vertical circuits, produce and control deflection

The same circuits, the horizontal circuits, produce and control deflection along the long dimension of the tube in all models. Therefore, wherever “vertical” appears in this manual of on the monitor wherever “horizontal” appears, it refers to the

Page 19

a nen gan aw a) + VERT sync Mon SNC.

oxo = VERT svc Won snc

i2ovac| soveons

a [ Ere DesaussING col 2. 3. « s 6:

K7000 COLOR MONITOR SCHEMATIC DIAGRAM

07 LATER PROGUCTION

108. VERTICAL SIZE

th52828..:-gP448*;
:S5238535cerAcrtnN
RRARAABA_—22,5mm NECK239.0 mm HECK’

p [SKTZO1 Y azo :

ateF

<a ose 22,25v

gee+R

or

3en21

. Aza

niteeeae]ESsee ME¥

ae Bhseos

e222Gre©tomvariegos=
380.aSee
au022baoarstsCUTOFF ORIVE CUTOFF DRIVE CUTOFF ORIVEiALTERNATE CRT AND NECK
“33eeeeresenEa——eeeaoano
«C12P2022
noSbso0maretiSdovWoeSaneSeeriesSa
SeteSoe$22xveoh
‘vecisorecawar3904
nase me sus 2oeFf

Ter B

esa2freYT__Bivere
:ze3R23SS ee0@
Tos7Seal ‘ceereevag{3K7800 SERIES
$3,MtoeENS:EnaxISK7600 SERIES
6Kow7S?BRIGHTNESSeyid
aCoesae:*A19K7900 SERIES
  • aw
nat|[--swutoown, gy,3:Lnote:
FaleAust.»501a0 o33,rfREFER To OTHER scHEMATIC
ai lped2c20, tecatReo4OLAGRAMS FOR CERTAIN UNIQUE
TEFioon, 2 (toe euro] [ae wearedeeeerecsMooccs

a6 Ge

aa as.«R39¢29RTORrSCREEN
OOFoscrG@2K0168K 47K.-7-
nse dorferaeSer;nares
oe]nso| tox8IfeootA“93{au nesearoms ane te, Sits ices ohio
aadoxcebans tdLESS OTHERWISE INDICATED.
ozanssossouvesHoRtzonTAL
nia’narqase se?300POSITIONos,2 CAPACITANCE VALUES LESS THAN | ARE 1H
idanssoa] 2te2R674)7TAMRava fescafaeriso0w7“SSomwenmse imoceaten
teas}JeeastorteasoonSRIVE,cae22cas©
Biefostatte 1 10ay100TF wontzonthi3 CIRCLED NUMBERS INDICATE LOCATIONS OF
asin]aecss3bres;Eearaine waveronm NEADINGS
caFon03s}
:aeezBO | nes

ES ‘Seow } 39K, sw

7 @nce | 38%G30"i
ENST | |28h)1eeeAN caution surety cortices component
.020Yow|200v1a)sposeGe2,20IK-RAY RADIATION RELATEO COMPOKEMT.

LF es2

cosWA20hatfares]peat ofLewoeREPLACE ONLY WITH SAME TYPE
et£7vess20F1|Tepa‘oot:PARTS AS SHOWN IN PARTS LIST.
tasv acaeR)thoes280%=ianina
Son’biliDareorrVERTTesla40asetrey

aixiw 23

patozz|Si..JAWHOLDqtEat025)Bee»
34Pesozthe400a
JS smos3RezLaksawste“arycasBo.seout42
15,303 330Kthy33Kon oe awveeSIZE"LINEAL
veeeranil &teAgaUST.
*3arA} VERTICAL15 cso,29 vas,Rew
1604}SIZErr2SVERTICALea
p23pozTreoPOSITION2 ees ee ee
+] 636220M38‘RIOO
sew'270,1Wroy *WARNINGS:

Race 1. Power Up Warning DEFLECTION An isolation transformer must be used between the AC supply and the AC plug of the moniter betore servicing, testing, YOKE or operating the monitor since the chassis and the heat sink are rectly connected to one side of te AC line which could

——-_——--present a Shock hazard

08 1s omesen ont on Belore senrcing is pertormed. read al the precautions labelled on the CAT and chassis.

Tax 7600S00se=:
:mies wontons”Ma8S-—50-conr2. [ DGRAY RADIATION WARNING NOTICE _]
WARNING : PARTS WHICH INFLUENCE X-RAY RADIATION IN HORIZONTAL DEFLECTION, HIGH VOLTAGE CIRCUITS AND: PICTURE TUBE ETC. ARE INDICATED BY (3 IN THE PARTS LIST FOR REPLACEMENT PURPOSES. USE ONLY THE TYPE ALTERNATE CIRCUIT FOR ‘SHOWN IN THE PARTS LIST.
  • High Voltage- This moritor contains HIGH VOLTAGES denved from power supplies capable of delivering LETHAL quantities of energy. Do not attempt (0 service until all precautions necessary for wortang on HIGH VOLTAGE equipment have been observed.
  • CRT Handiing— Care musi be taken nat to bump oF scratch the picture tube as this may cause the picture tube t0 implode resulting int ‘personal injury. Statter proot goggles must be wom when handing the CRT High vohage must De completely discharged Defore Randiing. Do rot handle the CAT by the neck 5.|_ PRODUCT SAFETY NOTICE
WARNING ::FOR CONTINUED SAFETY REPLACE SAFETY CRITICAL COMPONENTS ONLY WITH MANUFACTURER RECOM: MENOED PARTS. THESE PARTS ARE IDENTIFIED BY SHADING AND BY (A) ON THE SCHEMATIC KAGRAM, AVERTISSEMENT: POUR MAINTENIR LE DEGRE OE SECURITE OE LAPPAREIL NE REMPLACER LES COMPOSANTS OONT LE FONCTIONNEMENT EST CRITIQUE POUR LA SECURITE QUE PAR DES PIECES RECOMMANDEES PAR LE FABRICANT. For replacement purposes, use the same type oF specified type of wire and cable. assuring the positioning of the wires «S followed (especially for H.V. and power supply cweuits). Use of altematwe wiring oF positionng could result m damage to the monitor oF ma Shock oF fice hazard. -15-|
Page 20

VIDEO INTERFACE AND OUTPUT The red, green, and blue video inputs come into the monitor at P1. Isolation and attenuation is provided by emitter followers Ql, Q2 and Q3. Forced blanking of the video signals is provided by the circuit.of Q4, DS, D6, and D7. The forced blanking causes there to be an interruption in the video signal before it goes to the inputs of IC1. This interruption occurs between scan periods, while retrace is taking place; it is required by IC1. The farced blanking is not necessary for most video signals since they already have an interruption of video (blanking) between scan periods. Some do not; it is to accommodate such signals that the forced blanking circuit is included. —— The red, green, and blue signals go into IC1 at pins 2, 4, and

  • Their levels are controlled by the gain of separate channels of the contrast amplifier. The gain is controlled by a DC voltage input to pin 11, which varies with the setting of the contrast control.

IC1 provides bianking of the video during retrace in response to blanking pulses at pin 13, derived from the horizontal and vertical sweep circuits. IC1 also requires a gating signal at pin 12 in order to provide red, green, and blue outputs at pins 21, 19, and 17. If the gating signal is not present, IC1 will not provide video output signals. The gating signal comes from IC2, pin 12 and is derived from horizontal sync. ~

The brightness is varied by varying the DC level of the outputs at pins 17, 19, and 21. This is accomplished by varying the DC voltage input to pin 14. The video outputs from IC1 are provided via R30, R31, and R32 to the neck board where they are amplified by the video output stages Q201, Q202, and Q203 before being applied to the cathodes of the CRT through R10, Rit, and R12.

SYNC = Sync is applied at P1 (positive sync) or at P2 (negative sync). Composite sync should be applied only to the horizontal syne input of the appropriate polarity. Positive sync is inverted by Q5 and Q6 then applied through D3, D4 and ASI « to the sync amplifier Q7,

The sync amplifier output is applied through C22, R53, and

RSS to pin 14 of IC2. Pin 14 is the sync separation input.

The sync separator extracts the horizontal and vertical sync from each other-providing horizontal sync to the horizontal AFC circuit in the IC. A composite sync output is provided at pin 12. This output signal is used for gating IC1 the video interface IC and for triggering the vertical oscillator.

-16-; HORIZONTAL OSCILLATOR AND OUTPUT The horizontal AFC circuit of ICZ receives a horizontal sync input from the sync separator and a feedback signal at pin 1, derived from the horizontal output. Slight differences in frequency and phase of the two signals will cause the AFC to generate a correction voltage at pin 2. The horizontal oscillator inIC2 has its free running frequency determined by the RC time constant of C19, R56, R57, R58, and VR2, the horizontal hold contral. The horizontal hold control varies the horizontal frequency by varying the RC time constant. Slight correction in frequency is provided by a correction voltage at {C2, pin 3 which comes from pin 2 through R60. The oscillator output at pin 4 is amplified and shaped by the horizontal drive stage Q10. The drive signal is then coupled to the base circuit of the horizontal output transistor Q11 by the horizontal drive transformerT2. T2is used for impedance transformation to provide the Q11 base circuit with the low impedance source that it requires. ~ The horizontal output transistor Qi1 is operated as a switch. It is either on or off. It is turned on and off at the scan rate which is determined by the horizontal oscillator frequency which is ultimately determined by the incoming horizontal sync frequency. A yoke current with a sawtooth waveform is needed to deflect the beam linearly across the CRT. The beam begins at the center of the CRT and is deflected from center to right. This center-to-right deflection occurs when Q11 is turned on. The deflection yoke coupling capacitor C38, also known as the S-shaping capacitor, begins to discharge through the yoke; the discharge current causes the beam to be deflected to the right CRT edge. At this time, Q11 is turned off, and the current provided by C38 stops. As the current falls to zero, a voltage is induced across the yoke windings as the magnetic field collapses; an oscillation is produced by the yoke windings and C36, the retrace tuning capacitor. During the first half cycle of osciilation, the induced voltage is impressed on the collector of Q11, C36, and the primary of they flyback transformer Ti. This induced voltage is stepped up by the flyback transformer’s secondary winding. This high voltage is then rectified and applied to the high voltage anode cf the CRT. When this induced voltage occurs, the electron beam is deflected from the right edge of the CRT face to the left edge. This is called retrace. During the second half cycle of the oscillation (of C36 and the yoke windings), the voltage at the Q11 collector tries to go negative or below ground. When this happens, the damper diode (include in same package with Q11) becomes forward biased. The conduction of the damper diode allows energy stored in the horizontal system to decay linearly to zero, thus allowing the beam to return to the center of the CRT face. The. focus voltage and the screen, G2, voltage are obtained from the anode voltage with a resistor divider network within the T1 assembly. An auxiliary winding (pin 10) provides feedback.to the horizontal AFC through R71, R70, and C29. This signal is also used to furnish the horizontal blanking input to IC1 via C28, R69, and R68. The signal from the auxiliary winding at pin 5 of T1 is rectified by D14 and filtered to provide the +12VOC supply for the video interface and sync circuits. The auxiliary winding of pins 3 and 4 produces a signal which is rectified by 013 and filtered to produce the +24VDC supply for the vertical output circuit. The horizontal linearity coil L2 is a magnetically biased coil which shapes the yoke current for optimum linearity. The horizontal size coil L1 is a variable series inductor which is used to vary the horizontal size of the display.

HIGH VOLTAGE HOLD-DOWN CIRCUIT The high voltage hold down circuit is part of the main PC. board P447 of this monitor. The +12V OC supply is sensed via D10. Since the +12V DC supply is flyback pulse derived, the +12V DC supply will rise as the high voltage rises. \f the +12V DC exceeds a threshold which is set with VR8, then D12 will conduct, thereby providing drive to IC2, pin 5— holddown input of deflection oscillator IC. The drive being applied to pin 5 causes the horizontal oscillator within the IC to shut down-thus preventing the generation of high voltage. The horizontai oscillator will remain in its OFF state, even if the input to C2, pin 5 is removed, unless and until AC power is removed from the monitor input. The power may then be reapplied.

VERTICAL OSCILLATOR AND OUTPUT The composite sync ouput of IC2. pin 12 is filtered through the network of R65, C25,C24 and R66 so that only vertical sync is applied to the vertical trigger input at pin 11. The vertical oscillator frequency is controlled by the vertical hold control and its input to pin 10.

The vertical drive output at !C2, pin 7 is applied to pin 4 of (C3, the vertical output (C. Output current from IC3, pin 2 flows through the yoke to cause vertical deflection. During upward deflection, current flows out of pin 2, through the yoke, and into C50 to charge it. Downward deflection is caused by C50 discharging through the yoke in the opposite direction and back into IC3, pin 2. AC feedback is provided through the wiper of the vertical size control VR4 to IC2, pin 8in order to control the drive amplitude. DC feedback at IC2, pin 9 maintains good vertical linearity at all sizes. DC current from the +24V supply flows through R83 and through the yoke to provide downward raster shift. Some of this DC current is diverted from the yoke through the collector of Q9. The amount of this current which is diverted from the yoke can be varied by varying the base drive to QQ by adjusting VR3, the vertical position control, thus providing manual adjustment of the vertical position of the display. The drive signal at C3, pin 2 is also used to furnish the vertical blanking input to IC1, pin 13 via R63 and C14.

AUTOMATIC DEGAUSSING ADG The ADG circuit automatically demagnetizes the CRT. This circuit is activated only when the moniter is initially powered up after having been off for at ‘east 20 minutes. R105 is a positive temperature coefficient device. When it is cold, it has a very low resistance. As it gets warm, its resistance increases. If the monitor is cold when AC power is applied, then R105 with a low resistance allows current to pass through it, D23, D24, and the degaussing coil. As current flows through R106, it heats up and eventually has a very high resistance, allowing very little current to flow through it. The residual current now flowing through R105 Produces a voltage drop across R104 of less than 0.6 volts. This is not enough to forward bias 023 and D24, so there is no current through the degaussing coil. The process of initially having a large current through the degaussing coil and then having the current decay to zero is what produces the degaussing action. The degaussing current decays to zero before the CRT warms up, so the degaussing is completed before the picture comes on.

Page 21

_+ ° GENERAL REPLACEMENT PARTS LIST For all K7000 models except where noted.

for safety purposes. This monitor contains circuits and components inciuded specifically For. continued protection no changes should be made to the original design, and components shown in shaded areas of schematic, or A & on patts list should be replaced with exact factory replacement parts. “The use of substitute parts may create a shock fire, radiation orother hazard. Service should be performed by qualified personnel only

P447 MAIN BOARD 447 MAIN BOARD (CONT.)

208X2400-901

Rat. No.Parte.DescriptionRat. Ho.PartNo.Description

RESISTORS RESISTORS (Cont)

Ri340x2562-9945.6K Ohm 5% 0.25WRsg340x2103-93410K Ot5% 0.25W
RZ340X2562-9345.6K Ohm 5% 0.25REO340Xx2563-434§6K Om 5% 0.25W
RS340X2562-9245.8K Ohm 5% 0.25WR6}340X2332-9343.3K Ohm 5% 0.25W
Re34024729344.7K Otim 5% 0.25W:R62340X2122-8341.2K Oben 5% 0.25W
RS340X2472-9344.7K Onn 5% 0.25W2R63‘340XZ563-93456K Ohm 5% 0.25W
RG340X2472-8344.7K Ob 54 0.25WRed340x2184-934180K Ohm 5% 0.25W
R7340x2303-93433K Ohen 5% 0.25Res340212393412K Ot 5% 0.250
RB340X2333-93433K Ohm 540 0.25Reg340X2224-034220K Ohm 5% 0.25W
Ro340X2333-93433K Chm 5% 0.25R67340x2623.03462K Onm 5% 0.25W
Rio340X2151-934150 Ohm 5% 0.25WRES340X2223-93422K Ohm 5A 0.25W
ait340X2151-934150 Ot 5% 0.25WReg340X9683-231-68K SH O.SWCAR
R12‘340X2151-934150 Ohm 5% 0.25WR70340X2682-9346.8K Ohm 5% 0.25—
RI3340x2102-9344.0K Ohm 5% 0.25Wan340X3473-20447K 5% 0.5W:
Ria340X2102-0341.0K Ohm $46 0.25W-+R72340X2101-434100 Ohm 5% 0.25W
RIS340X2102-5341.0K Ohm 546 0.25WweRIB340X2103-03410K Ohm S% 0.25W
R16340X2822-9348.2K Ohm St 0.25WRT4340x2220-93422 Ohm 5% 0.25W
R17340X2822-9348.2K Ohm 5% 0.25WR75,340X2222-9342.2K Ohm 54% 0.2SW
RIB340Xx2152-93415K Ohm 5% 0.25WmaeRTE340X2473-934‘47K Ohm 5% 0.26W
R19340X2103-03410K Obhen 54% 0.25W-R77340X2333-93433K Ohm 5% 0.25
* R20340x2102-9344.0K Ohm 54 0.25WR76340X2102-9341.0K Ofim 5% 0.25W
Rat340X2583-93456K Ohm SA 0.25WREO340x30562345.6 5% 0.5W
22340X2562-8345.5K Ohm 5% 0.25WRi340x2150-93415. Ohm S% 0.25W
R23340X2102-9341.0K Ohm 54% 0.25Wa2340X3821-834820 Ohm 5% 0.5W
R24340X2224-934220K Ohm 5% 0.25WRE3340X3681-934680 Ohm 5% 0.5W
R25340227303427K Olin 5% 0.25Wor rAd340X2682-93468K Ohm 5% 0.25
R26340X2822-9348.2K Ohm 5% 0.25WRas340X2332-9343.3K Ohm 5% 0.25W
R27340222323422K Ohm 5% 0.25WREG340X2224-934220K Ohm 5% 0.25W
R28340X2332-9343.3K Ohm Si% 0.25W887-. 340X3334-844930K 10% 0.5W
29340X2103-93440K Ohm 5% 0.25WRES340x4182-6331.8K 54% 1W
R30340X2101-934100 Qhm 5% 0.25WRES043x0476-0022.9K 5% 5W MO.
ABU340X2101 934100 Ohm 54% 0.25RSO(043x0486-0021.2 Ste 2W MF
R32340X2101-934100 Ohm 5% 0.250a1043x0486-0021.2 5% 2W ME
Raa340X2102-0941.0K Chm $9 0.25WR92043x0486-0021.2 5% 2W ME
R3434021029344.GK Ohm 54% 0.25WRS3420X5102-3241.0K 5% 2W
R35340X2102-9341.0K Ohm $46 0.25WR94340X2473-93447K Ohm 5% 0.25W
Aa6340X2122-9341.2K Ohm 5% 0.25W9S340X2473-93447K Ohm 5% 0.25W
R37340X2822-0348.2K Ohm 5% 0.25WR96420X6182-3254.8K Ohm 5% 3W, WW
R38340X2122-9341.2K Ohm 5% 0.25WRO?- 420X6271-325270 5% 3W
R39340X2122-0341.2K Ohm Si 0.256R98340X4222-6332.2K Onm 5% 1W
Reg340X2102-9341.0K Ohm 54% 0.25WRSo340X4222-6332.2K Ohm 5% 1W
Rat340X2102-434YOK Ohm 5% 0.25WR190340X427 1-633270 5% iW
Rad340X2473-93447K Ohm 8 0.25WR101420X6682-3256.8K S% SW
Rag940X2222-8342.2K Ohm 5% 0.25WR102340X4470-63347 Sto 1W
Rag340X2104-934100K Ohm 5A 0.25WAxR103043x0483:0012.7 Ohm 5% 7W
Ras340X2104-9%4100K Ohm 5% 0.25WR104063X0484-00115 Ohm 5% 5W
R46340X2101-934100 Om St% 0.25WR105043X0485-001Thermisier
RAT40X2101-934100 Ohm 5%0.25WR106340K2273-93427K Ohm St 0.25W
R48340X2102-4341.0K Onm 5% 0.25WR107340X2102-0341.0K Ohm 5% 0.25W
Rag940X2102-9341.0K Otm $4% 0.25W8301043x0481-003220 Ohm 15W WW
SO340X2103-03410K Ohm 5% 0.25WvAt040x0653-002CTL 500
Rst340X2103-93410K Ohm S44 0.25WvR2040x0653-005CTRL 10K
Rs2340X2102-9341.0K Ohm 5% 0.25WvR3(040X0653-005CTRL 10K
aS3340X218 1-934150 Of 5% 0.265WRa040x0653-001CTAL 200
RSe340X2224-934220K Ohm 5% 0.25Wvas040X0653-006CTRL 200K
5534021010344100 Onm 5% 0.25WvRG940X0853-003CTRL 2K
R56340X2472-9344.7K Ohm 54% 0.25Wvar040X0653-005CTRL 10K
Be340X2182-9341.8K Otin 54 0.25WVRE040x0639-006Trim Pot 2K Ohm 0.3W
58340X2123-93412K Ohm 5% 0.25Wvag040x0655-001Trim Pot 200 Ohm

FINAL ASSEMBLY PARTS Ret. Ho. Part Ho. Description 13K7800 SERIES (13°)

At88X0236-506CRT Orion A34LL00X
  • 942800-001 Deflection Yoke 2A0690-001 Purity & Convergence Ring Assembly ‘9A2856-00: Degaussing Cod Assembly _ 6x0378-001 Ruoder Wedge 19K7600 and 19K7900 SERIES (19")
Ax88X0237-506CRI Philips MVA48ABKOSX
  • 942862001 Oentection Yoke 200690-001 Punty & Convergence Ring Assembly 942857-001 Degaussing Coil Assembly Runder Wedoe
Ret. No.Part No.DescriptionParito.Sescrption

CAPACITORS . SEMICONDUCTORS

cq080x0093-671Oise 22PF 10% NPOoYreceLeen abt
2080x0009-671Dise 22PF 10% NPO92Reerooreoo!inde INGA:
<3080x0099-671Disc 22PF 10% NPC4966x0070-001Diode 1N9148°
SbaSxost7 201Sie wavDs066X0070-001Dioga 13148”
cs.045%0577-501Hect 10MF NP 25V9s860079 001Disdettets
co(045x0877-501Elect 10ME NP 25V=eexo070-001Diode W918
c?047x0766-£02MYR 022 10% 50V-98ex0070-001Deis W848
ce047x0766-502MYR 022 10% SOVoagsen0070904Giode 169148
co(94 7X0786-502MYR_022 10% SOVo,Seeaora 20)kids 1NG148
copaarnseo ee!ate hyon068x0040-.028Zener Diode 5.1V 5% 0.5W
repPeereaeee er,012066x0040-005Zener Diode 10V 5% 0.5W
gupoetsMere013(066%0090:001D1 Fast SW AU-2
13(045x0560-534Elect 22MF 25V-oisGeemoeogo!D1 Fon Su Ru2
cua047X0786-502MYR 022 10% SOVwore‘9eexooad 003O1 Fast SW RU
cis(047x0786-502MYR 022 10% 50nS98620080 001Oy cae Sw rasa
cory947x0786-511MVR 1 10% SOVoreSeaxogsd gotor pea Sues
ouCenoeep etdsour io soy Pes018(066X0084.001Diode Sanyo GFE10A
ceeeetce edseasA019866X0091-00%Bide 51 14 600
S19046x0550-502FP 0056 2% AWS SOV&owSaekned1 001Siede S114
oePresidTe aA02(086x0081.001Diode SI 1A 600V
3separ 18aNA022066x0091.001Diode St 1A 600V
22045x0560514yt 1.0UF SovBepexans 031Boaes th
caReverenensOeO24066x0091-001Diode Si 1A 600V
24047x0786-503,MYA 068 10% SOVbas966x009 001Diode St
25047x0786-512P-Ester 015 10% SOV._ 2encereoya
oeceareeeSerAe SYa2086x0113-401TRSTR NPN 2N3904
eubeoxoose 45?See ee wy kaoa3086x0113-501TRSTA NPN 2N3904
esoeayense CeSPF 20s 2+ae(066x0113-501TRSTR NEN 2N3904
29047x0786-501‘OIOUF 10% SOV P-Estr7)SotaTeta NEN Net
ea‘Gooxnasa onsDine 00 20% ZF S0nvos086X01 13-501TRSTR NPN 2N3904
31047x0786-501OIOUF 10% SOV P-EstrOsgeeeis satSe
C22080x0089-680Dise 100 10% Z5F 500VaoFeeeTRSTR NEN aago4
633080x0099-722Disc .0033 10% YSP SOV3Geexn13-e04TESTA NEN 2NSGOS
cu080x0099-221Disc 01 10% Y5P SOV,oaes1 13 201Tea
cas,047x0786-501DIOUF 10% SOV P-EstronFeetelTASTA NEN CC
AxcasPopes y bnpr e100 2m 1800N,tc1(086X0186-001IC Video UPC 1397 NEC
ieEyerBaeTTee086x0187-001IC Honz Vert LA7823,
“eeoserieas elas a ae onan-1¢3088x0169-001(C Ver Output UPC1378
aDASKOSS0-0S3, =«Elect>Awa1086X0188-001Regulator (C STR3123
C41080%0099-505Disc .001 20% Z5F SOV-on
ca2(045X0560-006LYT 100UF 16V.7
3‘080x0099-505Disc .001 20% Z5F S00VDEMERS AND COILS
cas(046X0544 009110% 100¥ P-Frop
Cas045x0560-020LYT 470uF 16vTRANSFORME!Nn
C46045x0560-020UYT 470UF 16v*u0942854 001Coit Width-TOOAL
ca?‘080x0099-580Disc 100 10% 25 SOV#2(00942855.001Coil Lin TODA!
48(045¥0560-532Elect 100MF 35VAst053x0528-001Trarst Flyback
vas047x0786-501lOTOUF 10% SOV P-Este2082x0131-001Transt-Honz Orver
500450560023UT 1o00UF 25v-
csi045x0525-512Tan 68 10% 35V
¢s2(047Xx0766-601OLOUF 198. SOV P-Est~ad
53047X0786-514(O33UF Sa SOV P-Estr
C54047x0786-515MY8 022 5% SOVMISCELLANEOUS
cs5045x0578-001Elect 560 200V..AR016X0176-001Fuse 1.54$8
csé(045x0569-008LyT 22UF 160v(016x0182-001Fuse Clip
cs7048x0569.011- >“Elect 47 160VPr(00640428001Plug Header
aAcss080x0089-724Disc 0015 10% YSP SOOV-62006A0428-001Plug Header
aceo(980x0009-723Disc 0022 10% Y5P S00VPs006A0427-001Plug 2 Pin
Acé1080x0093-723Disc 022 10% YSP SOOVPa006A0406-001Plug 4-Pin OSHIMA
Acoz046X0S52-00"120% 125VAC°60060429005Plug Header
63047%0786-501‘Q1OUF 10% 50V P-Estr1202013x1243.001Cable Assy 4 Wire 350mm

P456 NECK BOARD (used with CRT’s with a 22.5mm neck diameter) RESISTORS CAPACITORS

R201340x2272-934Res 2.7K Obm 5% 0.250201080x0090006Cap 470PF 10% Z5F CER
R202340%2151 334Res 150 Ohm S4% 0.25€202080X0099-008Cap 470PF 10% Z5F CER
R203340x2272-34Res 2.7K Ohm 54% 0.25W203(080x0039-006Cap 470PF 10% Z5F CER
R204340X215 1-034Res 150 Ohmn 58 0.250208080x0039-221€Dise .01 10% YSP S00
R2053402272934Res 2.7K Ohm 5% 0.256205‘080x0099-225€ Disc 0015 15KV
R206340X2151-934Res 150 hn ee 0.25W
R207340x5682433Res 68K 2
R208,340X5682-633Res 6.8K 2” MOSEMICONDUCTORS
A209340xS682-633Res 68K 2W MO
R2r0Moxaa72.244Hee 27K Ore 10% 0SGi;“SeexoteecotTete scapes. ercoax
Raut340X3272-244Res 2.7K Ohm
apokeopNeOnaoNCaW.0203086%0184-001TASTR 2SC2068L 8. 88K
A213340X5689-333Rees 68 Olun $4 2W
vazo1(040x0653.003,CTRL 2«
vR202(040X0653-001ETAL 200MISCELLANEOUS
vR203(04040653-003,CTAL 2620200640429-005Plug Header
A204(040x0653-001TAL 200SkT20100340636001Pix Socket
va205‘940x0653-003,CrAL 2k46013x1243-001Cabie Assy 4 Wire 350mm
A206040x0653-001CTRL 200030%0797 001Plug V Pin

P448 NECK BOARD (Used with CRT's with a 29mm neck diameter) Same as P456 NECK BOARD except: SKT201 00340651-001 SOC CAT -17-|

Page 22

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 23

CROSS REFERENCE LIST: MONOBOARD ©

A084-91787-F000 ¥051-00114-F156

‘DESCRIPTIONQLY - DESIGNATION No.PART_NO.DESCRIPTION ©Qr¥YDESIGNATION NO.PART NO.
18 PF AX. CER.4 — 60,C62,067,C68QA15-00800-001174F001ile0A59-00803-0001
33 PE. AX. CER.2G,Cés0986-00800-030074E041ok0A59-10803-0034
47 PE AK. CER.6c47-c520986-00800-2600«7480811c 14K0A59-00803-0030
68 PE AX. GR.3C57,63,C640360-00800-0028-—«-74F101IC 90a59-00803~0002
210 PF AK. CER2&9,C700a15~00800-0013748742IC 26,1080859-00803-0003
390 PF AX. CER.5C1,€2,C41,C42,C550986-00800-300074F862Ic 10F,7H0a59-00803-0031
820 PF AK. CER.4c43-C460945-00816-0400—_74F1574IC SC,6C,8C,660aS9-00803-0004
-O1 UF AX. CER.146ce1-CP65,067-C1420986-00800-200074F1742Ic 8p, 2H0A59-00803-0005

ett €40,C58 C59, C61, C66

+] UE AX. CER.33380986-00800-1100_74LS002Ic 14A,6F0304-00803-0019
10 UF 25V AX. TANT.24,03909g6-00800-07007419021Iw0986-00803-7400
47 OF 25V_RD TANT1cs0A59-00800-000174LS082Ic 16,480986-00803-7300
100 UF 16V RD TANT1cee0945-00811-0500741203.Ic 2,3F,1280986-00803-1004
470 UF 16V AX.33,053,0540986-00800-2700- 74LS324IC 5F,1H,4K,1A0986-00803-6100
:::TALSSS1icw:QA59-00803-0026
6R58,R59,R61,R62,R64,100E-00005-00117418746IC 12B,15F,3K,5K,5K,0986-00803-1005,
aR65::18K
22 CBM 1/4W 53 CRBN.1R481O0E-00005-001s74LS862Ic 13C,8H-:0986-00803-9900
47 Oe 1/4 5% CRBN. - 4RBE-RIO,ROS1oo8-00005-002574181382IC 108,260986~-00803~-6500
68 OEM 1/44 5% CRN.4R50,R51,R91,R92100E-00005-002974US153 ~2.Ic 14c,15p0a59-00803-0006
82 Cam 1/4n 5% CRBN.7 ~~ -R9,R80,R87,R96,R97,100E-00005-003174LS1576IC 5A,3C,7C,7D,11D,36 “0304-00803-0021
ArR1O0,R10L74181611Ici0986-00803-1003
220 OEM 1/4W 5% CRBN.©0320RI4-RAS,100E-00005-004174LS1633.Ic 3D-5D@A59-00803-0008
410 OEM V/4w 52 REN. = 3REO, R63, R66100E-00005-00517411694IC 9%G,10G,7K,9K0304-00803-0023
510 CaM 1/4 5% CRBN.3.-R69,R72,R76100E-00005-0053JA4LS1731Ice0A59-00803-0009
560 OGM 1/4W 5% CRBN. = 3ST, R77, R78100E-00005-005474LS1743IC 12p,148,13K0304-00803-0024
680 O&M 1/40 5% CRBN. = 4,R94, R95, R9B,ROI100B-00005-0056T4LS1751Ic40304-00803-0025
1K ORM 1/44 5% CaN.5R68,R71,R73,R75,R86100B-00005~0061TALS1948 _ IC 13D,11E,13E,14£,0304~-00803-0026
2K OFM 1/4 5% CRBN.3-R67,R70,R74100E-00005-006812F-M4F,14G:
2.7K OEM 1/4W 5% CRBN.2—-R46,R471008-00005-0071TALS2448IC 8A-12A,4C,11¢,2p0986-00803-4800
A-TK OeM 1/40 5% CRBN. 20)RL, R2,RS-R7,RIO-R13,—_100E~-00005-007974LS2453IC 1B,88,1080986-00803-6400
7.:R49 ,R52-R56 ,R79,74LS2582Ic 136,13H0304-00803-0028
RB1-6474LS2736IC 6A,7A,15B,15C,10D, 0986-00803-4700
OK OFM 1/4a 5% GEN. = 2B, RA1008-00005-00883H
82K OEM 1/40 5% CRBN,«81RSOOE-00005-01127ALS2832IC 76,6)0304-00803-0030
7A4LS2982.Ic 15e,12KQA59-00803-0010
1k O&M 9 PIN SIP4-RMG-RMO1028-00004-0011«74183671il0986-00803-7000
2.7K O&M 10 PIN SIP4RML-RM4102E-00004-0020TALS3681Ic3E~0A59-00803-0011
4.7K OkM 10 PIN sIP1RS102E-00004-002674LS3748IC 12G,9H,11H,8J,10J, 0986-00803-4600

123,8K,11R

1N4148 DIODE.2.Di,D2103E-00002-000574L$3773IC 8F,128,1380a59-00803-0012
284123 NPN XSTR.2Qo104E-00001-000774LS3782Ic 7F,9Fgas9-00803-0013
244403 Pre xsTR.l@1048-00002-0006749042Ic 1D,4F0986-00803-6600
ue PNP XSIR6solo1048-00002-0012-« CDLARS RU. PAL1Ic061-00803-0001
NPN XSTR.104E-00003-000.
.°:YMOOLA HAL1Ic40986-00803-8900
20 MHZ Cosc.1Ice0304-00804-0007-« M¥002B HAL1IceH0986-00803-9000
..M0038 HAL1IcS0986-00803-9100
740611K0986-00803-7600MMCOG HAL1IcoHSee Ron/Epran Chart
PACNS REV 1.0 PLA1ww-AS9A-26AAJ-BXED
TANLS201Ice0a53-00803-0015

(HOSS REFERENCE LST: DESCRIPTION ay DESIGNATION ‘NO. PART NO.

PACOUT REV 1.0 PLA ROMCIPL REV 1.0 PLA

2018 2Kx8 RAM 45NS 2018 2Kx8 RAM 55NS 6116 2Kx8 RAM 120NS 6116 2Kx8 RAM 150NS 93419 €4x9 RAM

280B 2808 CIC + .8G0 64K ROM/EPROM BG) 64K ROM/EPROM FGO 256K ROM/EPROM FG] 256K ROM/EPROM FG2 256K ROM/EPROM FG3 256K ROM/EPROM PROGO 256K ROM/EPROM PROG] 256K ROM/EPROM

16 PIN IC SOCKET(.300) 20 PIN IC SOCKET{.300) 24 PIN IC SOCKET(.300)

24 PIN IC SOCKET(.600} 28 PIN IC SOCKET(.600)

40 PIN IC SOCKET(.600)

“AUTO INSERT PIN TIN .025 sQ

AUTO INSERT PIN TIN .025 Q

AUIO INSERT PIN TIN .025 SQ

AUTO INSERT PIN TIN .025 sQ

AUTO INSERT PIN TIN .025 99

AUTO INSERT PIN TIN .045 99

FERRITE BEAD

‘ZERO OHM RESISTOR (JUMPER) a Ic W Ic 133 a

IC 11G,10k,9J3,11J Ic loc Ic 11B IC 6B,9B Ic 4A Peed

Ic lc Ic 2c Tc 15A Ic 14B IC 8E IC 6E Ic SE Ic 4B Ic 3B Ic 5B BRP PP PP eee

v IcS 3E ICS 5G,5H,23,3J, 130 Ics 10C,4G,9D,11G, 6H, 93,11J,10K 3 ICS 68,98, 11B ou

10 ICS 4A, 15,38, 58,148, 2C, 4E-6E, BE 1 Icsic

2 3B

1s J4

8 JS

10 6

hia

LB FB1-FB13

6 il-IW6 AS9A-26AAJ-AXHD ASQA-26AAJ-CXHD

0a59-00803-0028 0A59-00803-0029 0A59-00803-0027 0aS9-00803-0014 0986--00803-9600

0304-00803-0041 0304-00803-0040 SEE ROM/EPROM CHART ‘SEE ROM/EPROM CHART SEE ROM/EPROM CHART SEE ROM/EPROM CHART SEE ROM/EPROM CHART SEE ROM/EPROM CHART SEE ROM/EPROM CHART SEE ROM/EPROM CHART

110E-00001-0003 110E-00001-0005 110£-00001-0009

110E-06001-0007 110£-00001-0010

110£-00001-0011

0304-00804-0009

0304-00804-0009

0304-00804-0009

0304-00804-0009

0304-00804-0003

0304-00804-0010

0316-00804-0002

117E-00001-0003

-19-|

Page 24

CROSS REFERENCE LIST: DESCRIPTION DESIGNATION NO. PART _NO..

SWITCH PC. MIG.Sa0986-00804-3100
10 POS. DIP SWITCHSA211.3E-00001-0004
sepMHQ30017-00007-0134

PC BOARD AC80-91787-F000 MONCBOARD A084-91787-F000 M0S1-00114-F156 DESIGIATION LIST: DESCRIPTION DESIGNATION NO. 1-65 -O1 UF AX. GR. P66 100 UF 16V RD. TANT 67-142 -O1UF AX. CER. cl,c2 390 PF AX. CER. 3 470 UF 16V AX. ELEC. c4 10 UF 25V AX. TANI. fos) 33 PF AX. CER. 6-C38 -1 UF AX. CER 39 10 UF 25V AX. TANT. 40 -O1 UP AX. CER 41,042 390 PF AK. CER. ©43-C46 820 PF AX. CER. 47-52 47 PE AX. CER. 53,054 470 UF 16V AX. ELEC. 5 - . 390 PF AX. CER. fost 47 UF 25V RD. TANT. cs7 68 PF AX. CER.

8,69|-O1 UF AX. CER.

60 18 PE AX. CER. col -Ol UF AX. CER. 62 18 PE AX. CER. 63 68 PF AX. CER.

064:68 PF AX. CER.

65 33 PE AX. CER. 66 01 UF AX. CER.

co7.18 PF AX. CER.

css 18 PP AX. CER. 59 270 PF AX. CER

c70-.270 PF AX. CER

RL,R2 4.7K OFM 1/4W. 5% CRBN. R3,R4 LOK Ob 1/4W 5% CRBN. RS-R7 4.7K Odd 1/4W 5% CRBN. RB 82K OEM 1/4W 5% CRBN. F9 82 OEM 1/40 5% CREN. R1O-R13 4.7K OBM 1/4W 5% CREN. R14-R45 220 OW 1/4W 5% CRBN. R46 RAT 2.7K OFM 1/4W 5% CRBN. R48 22 O&M 1/4W 5% CRBN. R49,R52-R56 4.7K 1/4a 5% CRBN. RSO,R51 68 OM 1/4W S% CRBN.

RS7:560 OFM 1/4W 5% CRBN.

R58 R59 10 O8M 1/4W 5% CRBN. R60 470 OBM 1/44 5% CRBN. R61,R62 10 O&M 1/4W 5% CRBN. R63 470 OBM 1/4 5% CRBN. R64,R65 10 OEM 1/4W 5% CRBN. R66 470 O&M 1/4W 5% CRBN. R67 2K ORM 1/4W 5% CRBN. R68 1k OM 1/4 5% CREN. R69 510 OHM 1/4W 5% CRN. R70 2K O8M 1/4W 5% CRBN. DESIGNATION LIST: DESCRIPTION DESIGQUTION NO. RTL 1K OHM 1/4W 5% CREN. R72 510 OFM 1/4W 5% CREN. R73 1K OHM 1/4W 5% CRBN. R74 2K ObM 1/4W 5% CRBN. R75 \K OHM 1/4W 5% CRBN. RIG 510 O&M 1/40 5% CRBN. R77 ,R78 560 OHM 1/4W 5% CREN. RI9 4.7K O8M 1/4W 5% CREN. R80 82 OHM 1/4W 5% CRBN. RG1-RB4 4.7K OM 1/418 5% CRBN. RSG 1K OFM 1/40 5% CRBN. R87 82 OFM 1/4W 5% CRBN. R88 47 OFM 1/41 52 CRBN. RB 47 O&M 1/4W 5% CRBN. R90 47 O&M 1/40 5% CRBN. ROL 68 OEM 1/4W 5% CRBN. R92 68 OFM 1/4W 5% CRBN. R93 47 O8M 1/4 5% CRBN. R94 680 CaM 1/4W 5% CRBN. ROS 680 OHM 1/4W 5% CRBN. R06 82 OH4 1/4W 5% CREN. R97 82 OFM 1/4W S% CRBN. FOS 680 OFM 1/4W 5% CRBN. R99 680 OFM 1/40 5% CRBN. Rid 82 OFM 1/4W 5% CRBN. RLOL 82 OEM 1/4W 5% CRBN. RML-RM4 2.7K OB 10 PIN SIP RS” 4.7K O&M 10 PIN SIP RM6-RMO 1K OH 9 PIN SIP DL,D2 1N4148 DIODE aL 2N4123 XSTR. - @ 2N4403 XSTR. 3 TIP110 XSIR. ue 2N4123 XSTR. ~ 6-010 MPSA7O XSTR. cla 7ALS32, Ic 4a 93419 64x9 RAM IC 5A 74LS157 IC 6A,7A 7ALS273 IC 8A-12A T4LS244 Ic 14a TALS0O Ic 15a BGO 64K ROM/EPROM Ic 1B 7418245 lc B NOT USED IC 38,58 PROGO,PROGL 256K ROM/EPROM IC 68 6116 2Kx8 RAM 150 NS. Ic 8B TALS245 IC 9B 6116 2Kx8 RAM 150 NS. IC 108 74.8245

Page 25

MONOBOARD 084-91787-F000 M051-00114-F156

DESIGNATION LIST:DESIGNATION LIST:DESIGNATION LIST:
+ DESCRIPTIONDESIGNATION NO.DESCRIPTIONDESIGNATION NO..DESCRIPTIONDESIGWTION NO.
Ic 1186116 2Kx8 RAM 120 NS.Ic 1G74LS08IC 12k7ALS298
IC 128,13874LS377IC 267418138IC 13K74LS114
Ic 14BBGl 64K ROM/EPROMIc 3%74LS157IC 14K74E08
Ic 15874LS273Ic 4GMMCOLA HALIc 15k74LS74
ic lc280B CPUIc 5G410038 HALICS 4A,15A,38,58 28 PIN IC SOCKET (.600)
Ic 2c2808 CICIC 6674E157ICS 68,9B,11B24 PIN IC SOCKET (.600}
Ic 3c74LS157IC 1GJ4LS283Ics 14B28 PIN IC SOCKET (.600)
Ic 4c7418244IC 8TALS\73Ics 1c40 PIN IC SOCKET (.600}
IC 5c,6C74F157:Ic 9G,10GTALS169> Ics 2c28 PIN IC SOCKET (.600)
Ic 7c74LS157Ic ic2018 2Kx8 RAM 45NSa_.Ics loc24 PIN IC SOCKET (.300}
Ic &C14F157:-.Ic 12674LS374Ics 9D24 PIN IC SOCKET (.300)
Ie 10c2018 2Kx8 RAM SSNS.IC 136TALS258:- 18 3E16 PIN IC SOCKET (.300)
“Ic licT4LS244Ic 4G7SLS194eeICS 48-6E,8E28 PIN IC SOCKET (.600)
IC 13¢TALSE6Ic 1H7ALS32Ics 4624 PIN IC SOCKET (.300)
Ic 14c74LS153Ic a7AE174oe-ICS 5G20 PIN IC SOCKET (.300)
Ic 15¢74LS273Ic 3H74LS273Ics llc24 PIN IC SOCKET (.300)
Ic74804Ic 4874LS08:Ics SH20 PIN IC SOCKET (.300)
Ic 274LS244,IC SHPALIcs 6H24 PIN IC SOCKET (.300)
“Ic 3D-SD74LS163Ic 6H10028 HAL-ICS 25,3J20 PIN-IC SOCKET (.300)
_“Ice74ALS20IC 7HT4E86Ics 93, 11g24 PIN IC SOCKET (.300)
Ic 774LS157Ic 88TALS86.,Tos 13520 PIN IC SOCKET (.300)
Ic spTAELI4IC 9H74374Ics 10K24 PIN IC SOCKET (.300)
Ic 9pColarb Rl PalIc 108748747-FB1-FB13FERRITE BEAD
Te lop748273Ic 1H74LS374~SwSHITCH PC. MIG.
Ic 1pTALS157Ic 12874LS20sw210 POS. DIP SNITCH
tc 12TALS174IC 138T4LS258W1-IW6JUMPER
Ic 13074LS194Ic 14874LS174aAUTO INSERT PINS TIN .045
1c 15D74LS153Ic Ww74LS55:-SQ. PIN
Ic le20 MHZ COSC.Ic 23PACNS REV 1.0 PLAS236AUTO INSERT PINS TIN .025
ic 2E74574Ic wPACOUT REV 1.0 PLA-.sQ. PIN
Ic 3574LS368Ic 43TALSLIS_M3SNAP
IC 45-6E,8©FG3,FC2,FG1,FGO 256K ROM/EPROMIc 6374.8283PC BOARDA080-91787-F000
Ic 9E74E10Ic 7JTALSO2
IC 10E7415138Ic74LS374Released 12 Sept: 86 QM
Ic lleTALS194Ic 952018 2Kx8 RAM 45NSRev. 1 - 20 Nov. 86 moved SH to chart. Om
Ic 12E74LS74Ic 10sTALS374
IC 13E,14ETALS194Tc llu2018 2Kx8 RAM 45NS
Ic 15E74LS298Ic 1237ALS374
clr74LS367Ic 130ROMCNIRL REV 1.0 PLA
IC 2, 3F74LS20IC 14gTALS161
IC 4P74804Ic 1K‘74504
Ic SF74LS32Ic 2K7406
Ic 6F74LS00IC 3K74LS74
.Ic 7F7418378IC 4K74LS32
jIC 8F74LS377IC 5K,6KTALST4
aIC OF7ALS378Ic 7K74S169
.ic 10F7486Ic 8K74L8374
Ic hie74F00IC 9K74LS169
]Te 12F-14r74LS194IC 10K2018 2kx8 RAM 45NS
iTC 15F74174Ic LK74US374

-21-|

Page 26

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 27

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 28

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 29

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 30

-26-|

Page 31

ea —— | ghee et or eres

-27-|

Page 32

-26-|

Page 33

-29-|

Page 34

err 8 .

  • <r]
Page 35

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 36

BALLY NIDMAY HFG. CO.

S68pr BAe? TH

Pe 2 ype 1

Page 37

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 38

HSYNC~ [>

svatnk [>

FB6 1 ~ | pg, 2__¥SYNC >

anai23 a4

cace:s>

9072 ec aL GND a2 az HEN

cs AS 93419 De oes BL o1~ p20 (0a

D4 DS Dé BDO27>

NOTES: C. MEDNICK BALLY MIDHAY HFG, CO.

MOHOBORRD PC.

Ae84-91787-Feeo hes1-90114-F129 SHEET 25 oF 25 [REV