Cloak & Dagger Kit TM-257 2nd Printing Installation for Defender
Cloak & Dagger (rev 5) (Atari, 1983) · Installation · 22 pages · 9 sections · original scan
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Atari Customer Service
If reading through this manual does notlead to solving a certain maintenance problem, call TELEHELP® at one of these Atari Customer Service offices:
UNITED STATES
Parts and Service
Atari, Inc. California Customer Service Office 737 Sycamore PO. Box 906 Milpitas, CA 95035 Telex 17-1103 (Monday-Friday, 7:30-4:00 pm Pacific Time) = From California, Alaska, or Hawaii (408) 943-1120 Ss From anywhere else in the continental United States toll-free (800) 538-1611
EUROPE Parts and Service
Atari Ireland Limited European Customer Service Office Tipperary Town, Ireland Telex 28165 (Monday-Friday, 9:00-6:00 pm GMT) @ 062-52155
Lty aa DACG Installation Instructions for Defender+
*A trademark of and licensed by Universal City Studios, Inc. t Trademark of Williams Electronics, Inc.
ii °1983 by Atari, Inc All rights reserved.
No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permisssion from the publisher.
The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976.
This Act provides for increased penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles.
In addition, the Act provides for payment of statuatory damages of up to $250,000 in certain cases. Infringers may also have to pay costs and attorneys' fees and face an imprisonment of up to five years.
Atari will aggressively enforce its copyrights against any infringers. We will use all legal means to immediately halt any manufacture, distribution, or Operation OF a copy OF video games made by us. Anyone who purchases such copies risks forfeiting such a game.
Published by: ATARI, INC. 790 Sycamore Drive P.O. Box 906 Milpitas, California 95035
Printed in the U.S.A. 12M
CLOAK AND DAGGER Installation Instructions TM-257
TABLE OF CONTENTS
Kit Parts Inventory. Tools Required...... Retrofit Instructions............ Remove Part of the Harness Assembly............ Remove the Game Printed-Circuit Boards... Remove the Control Panel......... Remove the Attraction Shield... Remove the Display Shield..... Install the Display Shield.. Install the Control Panel........ Install the Attraction Shield.. Install the Wood Panel for the EMI Cage. Attach the EMI Cage to the Wood Mounting Panel.... Install the CLOAK & DAGGER Retrofit Main Harness.. WODODDADADHDANWWHEEH
Perform a Self Test............ Apply the Labels.......... Attach the Side-Panel Decals....... Attach the Coin-Mechanism Panel Decal......e.cscececsseceees 14 Change Your Original Schematic Set To Reflect the CLOAK & DAGGER Retrofit....... cece ccc ce eee cccceneccntencecccccses 14
LIST OF ILLUSTRATIONS
Figure 1 Attraction Shield and Display Shield Replacement.... 4 Figure 2. Printed-Circuit Boards and Volume Control Removal.... 7 Figure 3. CLOAK & DAGGER Control Panel Installation.......... 8 Figure 4 CLOAK & DAGGER Harness and EMI Cage Installation... 1 Figure 5 CLOAK & DAGGER Decal Installation..........--.ee00.
LIST OF TABLES Table 1 Retrofit Kit Contents for Defender..........seeeeeeeeeee L Table 2 Tools Required........ccccecececeeccceccccenccencesese F
iii
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
CLOAK AND DAGGER Installation Instructions TM-257
CLOAK & DAGGER™* Installation Instructions for Defender**
INTRODUCTION
The following information includes the necessary installation instructions for changing the Defender™ game into a CLOAK & DAGGER™ game. The modifications include changing the cabinet graphics, the control panel, the attraction shield, the display shield, the game printed-circuit boards, and harness assembly. A CLOAK & DAGGER Schematic Package is provided for the game circuitry. If you have a schematic set that was originally provided for your game, save the power supply, sound printed-circuit board, and monitor schematics.
KIT PARTS INVENTORY
Check the contents of the CLOAK & DAGGER Retrofit Kit (A041462-01) before proceeding with the retrofit procedure. The parts included in this retrofit kit are listed in Table 1.
Table 1 Retrofit Kit Contents for Defender A041462-01
Part No. Quantity Description
| A037701-01 | 1 | Electromagnetic Interference (EMI) Cage and |
Guides Assembly—includes
| 037700-02 | 1 | EMI Cage |
| 178047-032 | 4 | PCB Guide |
| A040733-01 | 1 | EMI Shield and Dual PCB Assenbly——includes |
| A039431-01 | 1 | CLOAK & DAGGER Interconnect PCB |
| A039938-21 | 1 | CLOAK & DAGGER Slave PCB |
| A039942-21 | 1 | CLOAK & DAGGER Master PCB |
| A040404-01 | 1 | EMI Shield PCB |
| 72-1604F | 4 | #6-36 x 1/4-Inch Cross-Recessed Steel Screw |
| 034536-02 | 1 | 0.50-Inch Thick Foam Pad |
| 034536-03 | 1 | 1.12-Inch Thick Foam Pad |
—-continued on next page—
- A trademark of Universal City Studios, Inc. and licensed by Merchandising Corporation of America, Inc. **Trademark of Williams Electronics, Inc.
CLOAK AND DAGGER Installation Instructions T™M-257
Table 1 Retrofit Kit Contents for Defender (continued)
Part No. A041463-01 A041465~01 A040729-01 171021-001
A041509-01 A041402-01 119006-103
SP-242 ST-242-01
™-242
72~1816F
75-048S
75-018S
038086-01 038158-03 039450-01 041471-01
041471-02 041472-01 041473-01 041474-01
041476-02 041477-02 175004-—708
176015-112 Quantit'
Pe Pee
e
BPR ee Pee ES
Nee Descri _ Control Panel Assenbly-—includes Control Panel and Decal Assembly Control Harness Assenbly 8-Position Joystick Assembly
Retrofit Main Hamess and Component Assembly Main Harness 10 kQ Dual Potentiometer
CLOAK & DAGGER Schematic Package CLOAK & DAGGER Chart with Self-Test Procedure and Option Switch Settings CLOAK & DAGGER Operators Manual
#8-32 x 1-Inch Long Cross-Recessed, Pan-Head Machine Screw (used to mount wood panel to cabinet wall) #8 Split-Lock Washer (used to mount wood panel to cabinet wall) #8 Flat Washer (used to mount wood panel to cabinet wall)
Shock Warning Label Product ID Label FCC Compliance Label Left Side-Panel Decal
Right Side-Panel Decal Coin-Mechanism Panel Decal Display Shield Attraction Shield
Attraction Shield Semi-Rigid Film Wood Mounting Panel for EMI Shield Assembly #8 Flat Fiber Washer (used to mount EMI cage to wood panel) #10 x 3/4-Inch Long Cross-Recessed, Pan-Head Screw (one used to mount EMI cage to wood panel; two used on control panel)
The Master, Slave, and Interconnect Printed- Circuit Boards are already installed in the EMI Cage of the retrofit kit.
CLOAK AND DAGGER Installation Instructions ‘T™-257
TOOLS REQUIRED
The tools listed in Table 2 (or their equivalents) are required to perform a complete retrofit.
Table 2 Tools Required
Quantity Description Purpose
1 Phillips-head screwdriver Remove and install retainers, attraction shield, display shield, and harness Squeegee Install decal graphics X-ACTO™ blade or suitable Install decal graphics substitute me
RETROFIT INSTRUCTIONS
These procedures mast be performed by qualified service personnel. All interior and exterior surfaces should be clean and free of foreign material before starting this retrofit procedure.
The following procedures are arranged in a sequence recommended for performing the retrofit modification. The parts of your game that are affected by the retrofit (see Figure 1) are removed first. Then, the CLOAK & DAGGER kit parts are installed.
Unplug the game before performing the following procedures.
CLOAK AND DAGGER Installation Instructions TM-257
Upper Attraction | Retainer ' | | | a
Attraction Shield
Display Shield Retainer Lower Attraction Retainer
Display Shield
Figure 1 Attraction Shield and Display Shield Replacement
CLOAK AND DAGGER Installation Instructions T™-257
Remove Part of the Harness Assembly
10.
ll.
12.
DO NOT REMOVE the game harness wiring to the following items:
©@ Power Supply Transformer Connectors (see Figure 4) @ Fluorescent Tube er Speak . Safety Interconnect Switch at Rear of Cabinet On/Off Switch Monitor AC
Unlock and remove the rear access panel.
Unplug the coin-door connector.
Remove the coin-door interlock switch with a Phillips-head screwdriver.
Unplug the control-panel connectors.
Unplug the sound PCB connectors. Remove and discard the microprocessor and ROM socketed integrated circuits on the sound PCB.
Unplug the speaker connector.
Unplug two of the three power-supply base connectors. BE SURE TO LEAVE ‘THE TRANSFORMER CONNECTOR IN PLACE (see Figure 4).
Remove the volume control from the U-shaped bracket that is located on the side of the cabinet next to the sound PCB. SAVE THE BRACKET AND SCREWS FOR THE CLOAK & DAGGER VOLUME CONTROL INSTALLATION.
Unplug the signal connector on the monitor PCB.
Unplug the connectors from the game printed-circuit boards.
Remove the white nylon harness screw-down clamps that secure the loosened harness wires. BE SURE TO SAVE THESE CLAMPS AND SCREWS FOR INSTALLING THE CLOAK & DAGGER HARNESS.
Discard the removed harness.
CLOAK AND DAGGER Installation Instructions T™-257
Remove the Game Printed-Circuit Boards
Use the Phillips-head screwiriver to remove the screws that secure the three game printed-circuit boards to the cabinet (see Figure 2).
Remove the Control Panel
- Reach inside the game cabinet and release the two spring-draw latches on the sides of the cabinet to the rear of the control panel.
- From the front of the game cabinet, remove the control panel from the game cabinet.
Remove the Attraction Shield
Use the Phillips-head screwdriver to remove the hardware that fastens the upper attraction shield retainer to the cabinet (see Figure 1). Remove the retainer and the attraction shield. BE SURE TO KEEP THE HARDWARE AND RETAINER FOR REASSEMBLY.
Remove the Display Shield
Use the Phillips-head screwdriver to remove the hardware that fastens the plastic retainer to the top of the game display shield (see Figure 1). Remove the retainer and display shieid by pulling out on the retainer. BE SURE TO KEEP THE HARDWARE AND RETAINER FOR REASSEMBLY.
Install the Display Shield
- Slide the top of the CLOAK & DAGGER display shield into the groove of the display shield plastic retainer (see Figure 1).
- Slide the display shield (with plastic retainer attached) into the groove in the wood at the bottom or the monitor screen.
- Hold the retainer tight against the game cabinet and securely attach the top retainer to the game cabinet with the mounting hardware.
Install the Control Panel
- Position the CLOAK & DAGGER control panel on the game cabinet (see Figure 3).
- From the back of the game, fasten the two spring-draw latches at the sides of the cabinet and install the #10 x 3/4-inch pan-head screws to secure the control panel to the cabinet.
CLOAK AND DAGGER Installation Instructions T™-257
[ rere NOTE rrmgenict_ | Remove ROM & microprocessor integrated circuits
Sound Printed- Volume Control Circuit Board
Game Printed- Circuit Board
Figure 2 Printed-Circuit Boards and Volume Control Removal
CLOAK AND DAGGER Installation Instructions TM-257
CLOAK & DAGGER
Control Panel
Figure 3 CLOAK & DAGGER Control Panel Installation
CLOAK AND DAGGER Installation Instructions T™-257
Install the Attraction Shield
Slide the CLOAK & DAGGER attraction shield into the lower attraction retainer (see Figure 1).
Slide the CLOAK & DAGGER attraction film behind the attraction shield.
Hold the upper attraction shield retainer firmly against the top of the attraction shield and attach the upper retainer to the game cabinet with the mounting hardware.
Install the Wood Panel for the EMI Cage
Mount the wood panel included in the kit to the stand-offs on the cabinet wall with the four #8-32 x l-inch screws and #8 split-lock and flat washers (see Figure 4).
Attach the EMI Cage to the Wood Mounting Panel
1.
2. Slide the EMI cage into the wooden cleats on the mounting panel
Attach the EMI cage to the wood mounting panel with the #10 x 3/4-inch screw and the two #8 flat fiber washers (see Figure 4).
If you wish to change the option-switch settings, do so at this time. Refer to the CLOAK & DAGGER Operators Manual, TM-242, for further option-switch setting information.
Install the CLOAK and DAGGER Retrofit Main Harness (see Figure 4)
All CLOAK & DAGGER retrofit harness connectors are keyed to fit properly.
Install the volume control on the U-shaped bracket removed earlier. DO NoT attach the bracket to the cabinet wall at this time.
Plug the two keyed-to-fit 44-pin edge connectors into the EMI Shield PCB on the end of the EMI cage. Attach the ground clip to the bottom of the EMI cage.
CLOAK AND DAGGER Installation Instructions T™-257
Volume Control & Bracket
Metal Mounting Plate
‘Wood Mounting Panel
EMI Shield & Game
PCB Assy.
Power Supply
Figure 4 CLOAK & DAGGER Harness and EMI Cage Installation
CLOAK AND DAGGER Installation Instructions ™-257
9. Plug in the two keyed-to-fit power-supply base connectors. Secure the harness to the power-supply base with the white nylon adhesive-backed mount .
Plug in the three keyed-to-fit connectors to the sound PCB located on the cabinet wall above the EMI cage. Attach the grounding clip to the metal mounting plate behind the sound PCB.
Plug in the coin-door connector at the coin door.
Plug in the two control-panel connectors.
Plug in the speaker connector.
Plug the monitor-signal connector into position on the chassis-mounted main PCB.
Secure the CLOAK and DAGGER harness with the white nylon screw-on clamps removed earlier. Follow a routing similar to the original game harness. Attach the bracket/volume control to the cabinet wall.
Install the Self-Test Chart
2. Staple the CLOAK & DAGGER self-test chart on the inside of the rear access panel.
Install the rear access panel on the game cabinet.
Perform a Self Test
1. Plug the game in.
Turn on the game.
Perform the self-test procedure as described in the CLOAK & DAGGER Operators Manual, TM-242.
Ensure that the "EXIT" signs on both the right and left elevator doors are visible during normal game play by setting the width control to the narrowest width possible.
Apply the Labels
1. Remove the protective backing fram the product identification label, the FCC compliance label, and the shock warning label included in the CLOAK & DAGGER kit.
Apply the three labels to the back of the game cabinet directly above the rear access panel.
CLOAK AND DAGGER Installation Instructions ‘TM-257
Attach the Side-Panel Decals
We recommend that the following procedure be performed by two persons. One person may have difficulty handling the cabinet and the large decals.
Mix a normal dishwashing solution of approximately three quarts of water and any liquid dishwashing detergent in a shallow pan.
Tip the game cabinet sideways and gently lay it on a soft blanket.
Thoroughly clean the side of the game cabinet to ensure the removal of all dust,
Use a sponge to liberally apply the water and detergent solution over the entire side of the game cabinet.
Grasp the top edge of the appropriate decal for the side of the game cabinet. Hold the decal up off the floor and peel away the protective backing.
Gently lay the decal, sticky side down, in the center of the wet surface of the game cabinet (see Figure 5). Position the decal to ensure that the color graphics are centered on the side of the cabinet.
With the decal down and in position, use the squeegee to remove all the excess water and detergent from beneath the decal by quickly working from the center to the outside jes. Hint: If any air bubbles form, puncture them with a pin or the tip of an X-ACTO” blade. Rub gently with a soft cloth to disperse air.
Insert a #11 X-ACTO™ blade or suitable substitute between the T-molding and cabinet wall and, following the contour of the cabinet, cut off the excess decal. Rub the cut edges with a soft cloth to smooth down any rough edges.
When the wrinkles are removed and the decal is free of all excess water and detergent, gently turn the game cabinet over to the opposite side. Be careful to avoid damaging the freshly applied decal.
CLOAK AND DAGGER Installation Instructions
Figure 5 CLOAK & DAGGER Decal Installation TM-257
CLOAK AND DAGGER Installation Instructions TM-257
- Repeat steps 2 through9 for the remaining decal.
ll. Carefully raise the cabinet to the upright position.
- When both decals are firmly affixed, remove the protective covering.
- Use a lint-free cloth to wipe off any excess water and detergent from inside and outside of the cabinet. Allow time to dry before proceeding!
Attach the Coin-Mechanism Panel Decal
- Wet the cabinet surface surrounding the coin-door opening.
- Carefully position the lower edge of the decal across the bottom of the coin-mechanism area on the cabinet and gently smooth the decal into position with a sponge or squeegee.
Change Your Original Schematic Set to Reflect the CLOAK & DAGGER Retrofit
A CLOAK & DAGGER Schematic Package is provided for the game circuitry. If you have a schematic set that was originally provided for your game, save the power supply, sound printed-circuit board, and monitor schematics.
bad (BS IES ZEN DIES RAEN RAEN FEN EN FE
a ° > > a > > SS SS SS ES
Kit Warranty
Seller warrants that its electronic parts supplied in this kit are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. None of the Seller’s other products or parts thereof are warranted. Ifthe electronic parts supplied in this kit fail to conform to this warranty, Seller's sole liability shall be, at its option, to repair, replace, or credit Buyer’s account for such electronic parts which are returned to Seller during said warranty period, provided:
- Seller is promptly notified in writing upon discovery by Buyer thatsaid products are defective;
- Such products are returned prepaid to Seller’s plant; and
- Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation, or improper testing. Inno event shall Seller bé liable for loss of profits, loss of use, incidental or consequential damages. Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms herein, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products by Seller.
The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to you and others. Be very cautious in using non-Atari-supplied components with our games, in order to ensure your safety. Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor. a
© ©
© © © IS
ATARI
ATARI, INC. 790 SYCAMORE DRIVE PO. BOX MILPITAS, CALIFORNIA 95035 408/942-3100 ¢ TELEX 35-7488 °