Star Guards UR 3 Player (0E89-00300-0000)
Star Guards U.R. (Bally Midway, 1987) · Manual · 66 pages · 30 sections · original scan
STAR GUARDS U.R.
3 PLAYER
Cally MIDWAY MFG. CO. MFG.CO.
10601 W. Belmont 10601 W. Belmont Avenue
Franklin a anal 60134 Phone: (312) 451-9200 Cable Address: MIDCO =‘ Telex No.: 72-1596
OE89-00300-0000
THIS GAME MUST BE GROUNDED. FAILURE TO DO SO MAY RESULT IN DESTRUCTION TO ELECTRONIC COMPONENTS.
ELECTRICAL BULLETIN: FOR ALL APPARATUS COVERED BY THE CANADIAN STANDARDS ASSOCIATION (CSA) STANDARD C22.2 NO. 1, WHICH EMPLOYS A SUPPLY CORD TERMINATED WITH A POLARIZED 2-PRONG ATTACHMENT PLUG.
ATTENTION: POUR PREVENIR CHOCS ELECTRIQUES NE PAS UTILISER CETTE FICHE POLARISEE AVEC UN PROLONGATEUR. UNE PRISE DE COURANT OU UNE AUTRE SORTIE DE COURANT, SAUF SI LES LAMES PEUVENT ETRE INSEREES A FOND SANS EN LAISSER AUCUNE PARTIE A DECOUVERT.
C5%lly|MIDWAY
OUR TOLL FREE NUMBER FOR SERVICE INFORMATION CONCERNING THIS GAME, OR ANY OTHER BALLY/MIDWAY™ GAME YOU NOW HAVE ON LOCATION.
CALL US FOR PROMPT, COURTEOUS ANSWERS TO YOUR PROBLEMS
ANSWERS TO YOUR PROBLEMS.
Video or Pinball - Continental U.S. 800-323-7182
Cully MIDWAY 10601 West Belmont Avenue Franklin Park, Illinois, 60131 phone (312) 451-9200
©COPYRIGHT MCMLXXXVII BY BALLY MIDWAY MFG. CO. ALL RIGHTS RESERVED.
NO PART OF THIS PUBLICATION MAY BE REPRODUCED BY ANY MECHANICAL, PHOTOGRAPHIC, OR ELECTRONIC. PROCESS, ORIN THE FORM OF APHONOGRAPHIC RECORDING, NOR MAY IT BE TRANSMITTED, OR OTHERWISE COPIED FOR PUBLIC OR PRIVATE USE, WITHOUT PERMISSION FROM THE PUBLISHER. THIS MANUAL IS FOR SERVICE USE ONLY, AND NOT FOR GENERAL DISTRIBUTION. FOR PERMISSION REQUESTS, WRITE: BALLY MIDWAY MFG. CO., 10601 W. BELMONT AVE., FRANKLIN PARK, IL 60131.
Printed in U.S.A.
STAR GUARDS U.R. - 3 PLAYER
TABLE OF CONTENTS
SECTION 1 - SYSTEM INFORMATION Game DeSCription ...... cece ese c cece eee ee eens Se ee General Instructions: Installation, Servicing, & Self- Test eoees Option Switch Settings ..........- P.C. Board Reference Drawing . Trouble Shooting Procedure ...........
SECTION 2 - ILLUSTRATED PARTS BREAKDOWN Star Guards Front View: Picture ......cccecececccceeereeee Star Guards Front Yiew: Parts List Star Guards Rear Access: Picture ....... Star Guards Rear Access: Parts LiSt .e.sesseeeeeeeeene Header Fluorescent Light Assy.: Picture & Parts List . Joystick Assembly: Illustrated Parts . Coin Door (w/Cable) Front View: Picture Coin Door (w/Cable) Rear View: Picture ... Coin Door (w/Cable): Parts List ........ Power Chassis: Picture ......... Power Chassis: Parts List ....... ' REE ERR OoNnwNn VON OY YVAN yy
SECTION 3 - COMPONENT LAYOUTS, SCHEMATICS & WIRING DIAGRAM Monitor Oscilloscope Waveform Patterns & Troubleshooting Chart ..... seeeeee de Monitor Schematic .... ee ece cece cece eee eee eee te eens Son wewes - Monitor Theory of Operation .. - Monitor Parts List ........+.- Mono Board - Component Layout Mono Board - Parts List .... Mono Board - Schematic Sounds Good P.C.B. - Component Layout . Sounds Good P.C.B. - Parts List Sounds Good - Schematic ......eeeeeeeeeee eee e eens Dual Power Amp P.C.B. - Component layout. & Parts List < Dual Power Amp P.C.B. - Schematic ..... beeen eee e eres . Switching Power Supply P.C.B. - Schematic ... Uni-Power Supply Chassis Assy. - Schematic .. F.C.C. Filter Bd. - Component Layout & Parts lis a F.C.C. Filter Bd. - Schematic ............. aesees . Cabinet Wiring Diagram .......... cece e eee eee ~ 3-34 8 to 4 Multiplexer Bd. - Component Layout, “parts List & Schematic ......... 3-36 Eprom List .. Inside Back Cover
GENERAL INSTRUCTIONS
FOR
STAR GUARDS - 3 PLAYER -. UR.
INSTALLATION
- Remove keys from the taped coin return slot and unlock to open the coin box door.
- Remove four (4) “CABINET LEVELING LEGS" from inside the coin box.
- Tip the cabinet to the side and remove the shipping cleats from its bottom. Locate the threaded holes - one in each corner - and install the “CABINET LEVELING LEGS" in them. = Level the cabinet. ° When finished, the cabinet should be stable in the upright position.
- © Unlock and remove the rear access door to gain access to the 3-pronged line cord. Reinstall the rear access door,
- qaect the 3-pronged line cord to a 3-slot A.C. wall outlet to insure proper groundng.
- The power ON/OFF switch is located on top to the right rear of the cabinet as you face the cabinet.
TO SERVICE THE CONTROL PANEL
2°
ooo on
e200 Turn power to the game off. The control panel is held in place by two (2) latch clamps which provide constant pressure on the strikes. They can be reached through the coin door. To release the clamps, lift up and toward the center of the control panel. Once they are released, unhook them from their strikes. Swing out the controi panel on it's hinge for servicing. To resecure the control panel, reverse this procedure.
To remove the control panel for bench-servicing only:
With the control panel in it's open position, disconnect it from it's cabling. Remove the screws which secure the continuous hinge to the cabinet. The control panel is now loose and may be bench serviced. To reinstall the control panel, reverse this procedure.
REMOVAL OF THE VIEWING GLASS
Turn power to the game off and swing open the hinged control panel. This frees the viewing glass so it can be removed.
1-3
REMOVAL
REMOVAL
REMOVAL By putting your fingers in the slot in the middie of the main-display-glass support, the viewing glass can be removed as follows:
- Lift the glass up.
- Swing the bottom edge of the glass out slightly forward.
- Drop the glass down so that its’ top edge is slightly below the bottom edge of the speaker grille.
- Now, holding the glass by its' top edge and bottom edge, lift up and out. To reinstall the viewing glass, reverse this procedure.
OF THE HEADER (ATTRACT) GLASS
Turn the power to the game off. The glass is held in place by the speaker grille at the bottom and a retaining bracket at the top. The retaining bracket is secured to the cabinet top by five tamper-resistant screws. Remove these screws by using a special wrench provided in the Hardware and Bag Assembly. Remove the retaining bracket and slide the header glass up. This exposes the fluorescent light assembly. The fluorescent light tube may be replaced at this time.
- WARNING: If you drop a fluorescent tube and it breaks, IT WILL IMPLODE! Use care in handling. To reinstall the header glass, reverse this procedure.
OF THE FLUORESCENT LIGHT ASSEMBLY
Be sure the power to the game has been turned off. Disconnect it from it's power cable. Remove the fluorescent light assembly's three mounting screws and then remove the assembly from the cabinet. To reinstall the fluorescent light assembly, reverse this procedure.
OF THE SPEAKER(S)
Be sure the power to the game has been turned off. Remove the header glass and disconnect cabling from the speaker(s).
VOLUME CONTROL POT / OPTION SWITCH LOCATIONS
The volume control pot is located, along with the credit switch and the self-test switch, just inside the cabinet on the right side of the coin door frame. The option switch is located as shown in the attached p.c. board reference drawing. For adjustment, it can be reached
To make
To make through the game's rear access door.
the sounds louder, turn the volume pot clockwise as you face it.
the sounds less loud, turn the volume pot counterclockwise as you face it.
1-4
SELF-TEST MODE
The Self-Test mode is a special mode for checking the game switches and computer functions. It is the most complete way of checking for proper game operation and is quite easy to use.
The Self-Test mode may be entered at any time and from any mode of operation. Simply locate the black slide switch inside the coin door and slide it to the Self-Test position. With this switch in the Self-Test postion, activate the slam switch located on the Coin Door. The game will enter the Self-Test mode immediately and display the following test menu....
INPUT TEST OUTPUT TEST DIPSWITCH OPTIONS SELF=-DIAGNOSTICS GRID TEST OPwNe
TO MOVE CURSOR UP, MOVE ANY JOYSTICK UP. TO MOVE CURSOR DOWN, MOVE ANY JOYSTICK DOWN. To EXECUTE TEST, PRESS ANY START BUTTON.
- INPUT TEST: This test is designed to confirm the operation of player input switches and device switches in the game. When you enter the test, the screen displays the following:
COIN CHUTE 1 ....eeeeeeee PLAYER 2 BUTTON COIN CHUTE 2 .. see LEFT JOYSTICK 2 ... COIN CHUTE 3 .. RIGHT JOYSTICK 2 CREDIT BUTTON ..
PLAYER 1 BUTTON .....-.seeee PLAYER 3 BUTTON LEFT JOYSTICK 1 .. sees LEFT JOYSTICK 3... RIGHT JOYSTICK 1 RIGHT JOYSTICK 3
- All joystick switches are open: 1 = Open Switch & 0 = Closed Switch.
When you activate any one ot the above switches, its' respective message "OPEN" changes to "CLOSED" except for LEFT JCYsTICK 1 (2 and 3) and RIGHT JOYSTICK 1 (2 and 3). For -ny one of these six:
JOYSTICK POSITION CH DISPLAY JOYSTICK POSITION SWITCH GiSPLAY UP TITO UPPER LEFT DIAGONAL 10 DOWN 1101 UPPER RIGHT DIAGONAL 0110 LEFT 1011 LOWER LEFT DIAGONAL 1001 RIGHT 0111 LOWER RIGHT DIAGONAL 0101
To exit this test, activate the coin door slam switch.
- OUTPUT TEST: This test is designed to confirm the operation of all 3 players’ Start button lights. These lights will flash in sequence with the following messages displayed on the screen:
START BUTTON 1 LIGHT ON START BUTTON 1 LIGHT OFF
START BUTTON 2 LIGHT ON START BUTTON 2 LIGHT OFF
START BUTTON 3 LIGHT ON START BUTTON 3 LIGHT OFF 1-5
SELF-TEST MODE, Cont'd.
This cycle continues unless:
A. You press any one of the Start buttons to hold a light ON. B. You exit the test by activating the coin door slam switch.
- DIP SWITCH OPTIONS: All game options such as “energy units/coin” and "difficulty levels" are adjusted through the use of dip-switches located on the Monoboard. When this test is selected, a full display of the current dip-switch settings will appear on the screen (see "Option Switch Settings" on page 1-7). To exit this test, activate the ~ coin door slam switch.
- SELF-DIAGNOSTIC TEST: This test is designed to effectively locate and identify any malfunction of the on-board computer. when selected, the game enters this mode immediately and begins scanning the memory stored in rom and ram. If the test is successful, at the end of the scan "ALL TEST OK" is displayed on the screen. If a defective component is found during the scan, that component and its' location will be displayed on the screen. The entire test is performed approximately in 15 seconds. To exit the test, activate the coin door slam switch.
- GRID DISPLAY: This test is designed to display a crosshatch pattern used in adjusting the color monitor. This pattern may be used to adjust convergence, color balance, vertical linearity, and vertical/horizontal size. To exit this test, activate the coin door slam switch.
POWER-UP TEST MODE
This test sequence is designed to effectively locate and identify any malfunction of the Sounds Good p.c. board, Tesi results are indicated by an L.E.D. located on the sourd board.
On power-up under normal ope~ation, the sound board runs through its' self-diagnostic checks flashing its’ L.E.D. to announce every successful test. At the end of the test run, the attract mode begins.
If one of the tests fails however, the L.£.D. will not flash for the failed test no~ for any remaining tests in the sequencial run. At this point, "SOUND BOARD INTERFACE ERROR” appears on the screen.
The following is the Self-Test routine for the Sounds Good Board:
1st FLASH - Determines if the ROM (U7) is good. 2nd FLASH - Determines if the ROM (U8) is good. 3rd FLASH - Determines if the ROM (U17) is good. 4th FLASH - Determines if the ROM (U18) is good. 5th FLASH - Checks to see if the RAM (U6, U16) is good. 6th FLASH - Checks the PIA (6821) (U9).
1-6
STAR GUARDS UR.
OPTION SWITCH SETTINGS
PULELITELLLTATTLTT 441 SATTCH NO. 2 ~ AT AY3 - LOCATED ON MONOBOARD //////////// 0001111111
SW#L SW#Z SW#3 SWHA SWH5S SWE SWE? SWH8 SWHO SWH1O Nor NOT rr USED USED
ENERGY UNITS/COIN
8 ENERGY UNITS7COIN
10 ENERGY UNITS/COIN 12 ENERGY UNITS/COIN 14 ENERGY UNITS/COIN
ATTRACT Srnuence SOUNDS: ND: NO SOUNDS
OIFFICULTY LEVEL: —TERSY MEDIUM HARDER HARDEST
VIDEO FREEZE MODE: NORMAU VIDEO FREEZE VIDEO
FACTORY SETTING - ALL LOGIC SWITCHES SET IN THE “OFF” POSITION | PART NO. M051-00E89-A007
1-7
P.C. BOARD REFERENCE DRAWING
FOR _MONOBOARD SYSTEM i
MONOROARD A084-91787-ABB9
OPTION SWITCH "2" (10-POS1 TION)
INTRODUCTION
This manual offers generalized troubleshooting procedures for common types of malfunctions which can be applied to most video games. We will not attempt to give you specific instructions for troubleshooting particular games because this would involve hundreds of pages of more repetitive instructions, differing only in the specific details of each game.
The most common problems occur in harness components such as the coin acceptor, player controls, interconnecting wiring, etc. These areas are covered in moderate detail.
The TV Monitor and Game Logic Printed Circuit Boards (PCB's) provide their fair share of problems too, but not to the extent of the harness and its component parts.
As you already know, the Game Logic PC Boards are complex devices. Each contains a great number of different interrelated circuits. The major changes which give each game its own particular individuality are accomplished in the EPROMS and other Integrated Circuit devices that are installed on each of these PC Boards.
GENERAL TROUBLE SHOOTING SUGGESTIONS
The first step in troubleshooting is to correctly identify the malfunctions symptoms. This includes not only the circuits or features malfunctioning, but also those still operational. A carefully trained eye will pick up other clues to what's wrong as well. For instance, a game in which the computer functions fail completely just after money was collected may have a quarter shorting the PCB traces. Often an experienced troudleshooter will be able to spot the cause of a problem even before opening the cabinet.
After all the clues are carefully considered, the possible malfunctioning areas can be narrowed down to one or two good suspects. Those areas can be examined by a process of elimination until the cause of the malfunction is discovered.
HARNESS COMPONENT TROUBLESHOOTING
Typical problems falling in this category are coin and credit problems, power problems, and failure of individual features.
NO GAME CREDIT - - For example, a prospective game player inserts a quarter or token and is not awarded a game. The first thing to check is whether or not the quarter or token is returned. If it was returned, the malfunction most certainly lies in the coin acceptor itself. First, use a set of test coins (both old and new) to ascertain that the player's coin is not undersize or underweight. If your test coins are also returned, coin acceptor servicing is indicated. Generally, the cause of this particular problem is a maladjusted magnet gate. Normally, this will mean slightly closing the magnet gate by turning the adjusting screw out a dit.
1-9
If the quarter or token is not returned and there is no game credit, the cause of the malfunction may be in one of several areas. First, try operating the coin return button; if the coin is returned, the problem is most likely in the magnet gate. Enlarge the gap according the coin acceptor manufacturers service procedures. If this does not cure the problem, remove the coin acceptor, clean it, and perform the manufacturers suggested major adjustment procedure.
If the trapped coin is not returned when the wiper lever is actuated, you may have an acceptor jammed by a slug, gummed up with beer, a jammed coin chute, or mechanical failure of the acceptor mechanism. In this case, first check for the slug that will generally be trapped against the magnet. If a slug is found, simply remove it and test the acceptor. If the chute is blocked, remove the acceptor and remove the jammed coins. If there is actual failure of the acceptor, remove the unit and repair as indicated by the acceptor manufacturers service procedures.
If the coin is making its way through the acceptor (that is, falling into the coin box), yet there is still no game credit, you either have a mechanical failure of the coin switch or electrical failure of the coin and credit circuits. The first place to begin is by checking the coin switch. Most of these switches are the make/break variety of micro switch. They are checked for continuity between the “NO", "NC", and "C" terminals. When not actuated, the “NC" and “C" terminals should be continuous and the "NO" terminal open. When actuated, the "NO" and "C" terminals should be continuous and the "NC" terminal open. If the coin switch checks good, inspect the solder connections to the coin switch terminals to be sure there is good contact at this point. If necessary, use a continuity tester and check from the terminal lug on the switch to the associated PCB trace. This will tell you if there is a continuous line all the way to the credit circuit.
If the coin switch wires do check good, the problem is in one of the game logic boards - most likely in the coin and credit circuitry.
If you do get a game credit when a coin is deposited, but the game will not start when the one or two player start button is pressed, there may. be a problem in the start switch, the interconnecting wiring, or the gaine logic boards. First, check the switch. If the switch is OX, proceed to check the wiring. Again, make sure you go from the terminal lug on the switch to the PCB trace. This way, you will check the terminal contact as well as the PCB edge connector contact. If the wiring is continuous, proceed to check the PCB credit circuit. If mot, check each section of the wiring, until the discontinuity is located. If the wiring is OK, the problem must lie in the games logic boards.
TRANSFORMER AND LINE VOLTAGE PROBLEMS
Your game MUST have the correct line voltage to operate properly. If the line voltage drops too low, one of the games logic circuits will disable the credit acceptance circuit. The point at which the games logic circuits will fail to function is approximately 105 volts AC.
Low line voltage may have many causes. Line voltage normally fluctuates a certain amount during the day as the total usage varies. Peak usage times occur mainly at dawn and/or dusk. So if your games problem seems to be related to the time of day, this may be a factor. A large load connected to the same line as the game (such as a large air conditioner or other device with an exceptionally large electric motor) may drop the line voltage significantly when starting up. This drop can result in an intermittent credit problem. In addition, poor connections in the location wiring, plug, or line cord may also cause a significant drop in power. Cold solder joints in the games harness, especially in areas like the transformer connections, interlock switch, or fuse block, may also produce the same results, although probably on a more permanent basis.
Sometimes location owners (especially in bars) replace light switches with dimmer rheostats, and the game is sometimes on the same line. Obviously, the voltage available to the game is going to drop dramatically when the dimmer is turned down.
In any case, the way to check for proper line voltage is with your VOM. Set the VOM to the 250 VAC scale and stick the probes into the wall outlet the game was connected to. If it's OK here, check the transformer primary connections. If you do not get 117 VAC, examine the solder joints on the transformer, fuse block, and interlock switch. If you do get 117 VAC, the problem must be either in the transformer, harness connections, or in the PCB power supply.
If you suspect the transformer, check its secondaries with the VOM set to the 50 VAC scale and correlate the readings with the legend on the side of the transformer. The transformer must also be correctly grounded, so check the ground potential as well, especially if there is a hum bar rolling up or down the Monitor screen.
NO POWER, NO PICTURE - - If the Monitor screen is completely dark, first look in back of the Monitor to see if the CRT filament is glowing. If it is, try adjusting the brightness control.. If no luck here, put your ear near the Monitor and listen for the high-pitched B+ hum produced by the flyback transformer. If you get the hum but no picture, and you have tried adjusting the brightness, major Monitor servicing is indicated. : If the monitor seems completely dead, check the rest of the game to see if it has power. If it doesn't, go directly to the wall outlet and check there. If OK there, check the game fuse(s), interlock switch, and interconnecting wire lengths.
Sometimes it is difficult to tell if a slow-blow fuse has blown. If in doubt, check it using any of the VOM "R" scales.
HARNESS PROBLEMS - ~- Other harness problems include blowing fuses and malfunctioning controls. The repeating blown-fuse problem can sometimes be quite exasperating to solve. Short circuits have the tendency to occur in areas almost impossible to find. First, try inserting a new fuse as old fuses age and sometimes blow without cause. If the new fuse also blows, you definitely have a short.
The best way to approach this problem is by disconnecting devices that may be causing the problem, such as the TV Monitor, the various PCB's one at a time, and the isolation transformer. Disconnect the devices by FIRST turning the game off, disconnecting it from its wall outlet. Remove the blown fuse and connect your VOM across the terminals of the fuse block (this will save blowing a fuse each time you want to check the circuit). Set your VOM to one of its resistance scales. You should be reading a short. If not you probubly have a part that only shorts out after it is heated up - we'll) cover this in a minute. So, assuming you are reading a short on your VOM, disconnect the components from their cabling one at a time, checking the VOM after each one is disconnected. When the short disappears, you have just disconnected the bad component. If all components are disconnected and the short still remains, the problem is in the harness and only patient exploration will reveal its location. Carefully examine all the wiring, looking for terminals that may be touching, metal objects such as coins shorting the connections, or burned insulation. If necessary, use the VOM to check each suspected wire.
OK, now lets assume that you connected your VOM across the fuse block terminals as stated above and you did not read a short. This most likely means that you have a component somewhere in that game that ONLY goes bad AFTER it heats up. It checks good when its cold. In this case, turn the game off and disconnect ALL of its components. Install a known good fuse in the fuse block. And turn the game on. If the fuse does not blow after a few minutes, you know that it is not anything to do with the wire harness. (In this instance, it shouldn't be, actually. But it never hurts to check.) Next, turn the game off again and reconnect ONE component. Turn the game back on and wait a few minutes to see if the fuse blows. If it does not, turn the game off again and reconnect another single component.
Turn the game back on and wait a few minutes to see if the fuse blows. Repeat this procedure until the fuse blows. When it does blow, the last component you connected has the part on it that is going bad after it warms up and is shorting out.
MALFUNCTIONING CONTROLS - - The most common problem here is the bad potentiometer (pot). Typically, a bad pot will cause the image on the screen to jump when it reaches a certain point. The only cure for this one is to install a new pot.
If a feature that is operated by a switch (for example, joysticks, foot pedals, control panel buttons) does not operate at all, check the switch with a VOM or continuity tester to verify its operation. If the switch does not check good, replace it. If the switch is OK, you should suspect the input to the switch from the PCB. In this case, get out the harness and logic schematics and check to see what kind of input is supposed to be at this switch. In many cases, the input will be +5 volts DC. If so, use the VOM to check its presence with the game turned on. Normally, the switch is used to pull a +5 volt DC line LOW to GROUND or to pull a LOW line HIGH. If the PCB output is missing, check the wire length from the PCB. If you find the signal at the PCB trace, the wire length or connection is at fault. If there is no signal at the PCB trace, begin exploring the PCB using the logic schematics and game manual.
SECTION 2
{LLUSTRATED PARTS BREAKDOWN
STAR GUARDS U.R. - 3 PLAYER ~ FRONT VIEW
STAR GUARDS U.R. - 3 PLAYER - FRONT PARTS LIST ORDER BY PART NUMBER ONLY
ITEM PART NO. DESCRIPTION
| 0£89-00900-00XF [HEADER GLASS: SCREENED A595-00011-0000 /HEADER FLUORESCENT LIGHT ASSY. (BEHIND HEADER SEE PG. 2-9)
0017-00101-0138 |#8 X 5/8" TORX TAMPER RESISTANT PAN SCREW (11 REQ'D.)
0017-00009-0522 |LONG ARM KEY: (FOR ABOVE SCREW) TAMPER RESISTANT
MAIN VIEWING GLASS
WELLS-GARDNER - 19" COLOR DUAL SYNCH HORIZONTAL MTG. MONITOR
CONTROL SHELF ASSY.: (INCLUDES ITEMS 20 THRU 31),
- al 0017-00009-0534 |/BASSICK CLAMP (2 REQ'D.) (NOT SHOWN)
- 0555-00901-0000 |PIN: LOCATING (MOLDED) (8 REQ'D.) (NOT SHOWN) 11 [000-0002 COIN DOOR FRAME: LARGE BLACK, TRIPLE 12 A982-00014-0021 |U.S.A. 25¢ COIN DOOR & CABLE ASSY.
13 0017-00009-0477 |CASH BOX: MOLDED (BEHIND COIN DOOR)
14 0950-00115-0000 |COVER: COIN BOX (BEHIND COIN DOOR)
15 0950-00901-0000 | BASKET: COIN BOX - WIRE (BEHIND COIN DOOR)
16 0017-00102-0048 |LEG LEVELERS (4 REQ'D.)
| 17 0017-00103-0026 |NUT 3/8 -16 HEX (FOR LEG LEVELERS) (4 REQ'D.) 7 0935-00906-1100 |PLATE: KICK L = 27 - 5/8" 19 0£36-00105-0100 |BRKT.: SHELF-SUPPORT: RIGHT (UNDER CONTROL SHELF)
20 0£36-00105-0200 |BRKT.: SHELF-SUPPORT: LEFT (UNDER CONTROL SHELF
- NOT PART OF ABOVE ASSEMBLY & MUST BE ORDERED SEPARATELY
2-3
STAR GUARDS U.R. - 3 PLAYER - FRONT PARTS LIST, CONT'D.
ORDER BY PART NUMBER ONLY
DESCRIPTION
CONTROL - APRON WELD ASSY.
CONTROL SHELF CABLE ASSY. (UNDER CONTROL SHELF)
JOYSTICK - ASSY.: SHAFT & PLATE (6 REQ'D.) (SEE PAGE 2-10) OR
JOYSTICK - ASSY.: SHAFT, BALL & PLATE
PLATE: CONTROL SHELF
OVERLAY: CONTROL~SHELF
26 0017-00032-0093 )SWITCH: SPST PUSHBUTTON W/RED LIGHT (3 REQ'D.)
OE36-00106-0000 |STRIKE: CONTROL-SHELF (2 REQ'D.) (UNDER CONTROL SHELF)
0017-00101-0138 |#8 X 5/8" TORX TAMPER RESISTANT PAN SCREW (8 REQ'D.) 0£89-00501-0000 |CONTROL SHELF: WOOD
0017-00101-0620 |8-32 X 1/2" CARRIAGE BOLT (24 REQ'D.)
0017-00103-0061 |NUT: 8-32 HEX W/SEMS (28 REQ'D.)
2-4
STAR GUARDS U.R. - 3 PLAYER - REAR ACCESS
2-5!
STAR GUARDS U.R. - 3 PLAYER — REAR ACCESS
2-6
STAR GUARDS U.R. - 3 PLAYER - REAR ACCESS PARTS LIST
ORDER BY PART NUMBER ONLY
DESCRIPTION
0017-00003-0465
B084-90910-F 000 WELLS-GARDNER - 19" COLOR DUAL SYNCH HORIZONTAL MTG. MONITOR
DUAL POWER AMP P.C.B. ASSY.
AE89-00011-0000 |CARDRACK W/SOUNDS P.C.B. ASSY. (SEE PG. 2-5)
A385-00024-0000
AE89-00012-0000 B084-91863-AE89 |PROGRAMMED SOUNDS GOOD P.C.B.
BRACKET, SHIELD & SPACER ASSY.
CARDRACK W/MONOBOARD ASSY. (SEE PG. 2-5)
B084-91787-AE89 PROGRAMMED MONOBOARD ASSY.
AE36-00013-0000 SHIELD & SPACER ASSY.: MONOBOARD
AE68-00006 -0000 +—___ MASTER CABLE W/BRKT. ASSY.
A515-00021-0000 MULTIFUNCTION SWITCH BRKT. ASSY. (INCLUDES FOLLOWING 6 ITEMS)
0017-00032-0007 SWITCH: SPDT SLIDE 4 AMP
0515-00107-0000 BRKT: CREDIT: TEST-SWITCH: VOLUME
0017-00032-0051 BUTTON: SWITCH, RED
105E-00001-0017 POT.: O-1K CBN 1/2W
0017-00103-0075 NUT: 3/8 - 32 HEX
0017-00104-0104 WASHER: .375" 1.D., .562" 0.D., .018 TH. INTERNAL TOOTH LOCK
AE36-00008-0000 HIGH VOLTAGE CABLE ASSY.
0017-00003-0500 LINE-CORD: 3-CONDUCTOR 18 AWG.
AE36-00002-0000 = VIDEO CABLE ASSY.
2-7
STAR GUARDS U.R. - 3 PLAYER - REAR ACCESS PARTS LIST (CONT'D.)
ORDER BY PART NUMBER ONLY
ITEM PART NO. DESCRIPTION
10 AE36-00003-0000 {AUDIO CABLE ASSY. (SEE PG. 2-5)
11 A945-00059-0200 |POWER CHASSIS: 130VA - SWITCHING (SEE PG. 2-17)
AE89-00500-0000 {CABINET ASSY. (INCLUDES ITEMS 12 & 13)
12 0E68-00500-0000 | CABINET
13 A961-00007-0000 |CASTER-WHEEL ASSY. (INCLUDES FOLLOWING 4 ITEMS) (2 REQ'D.)
0017-00042-0255 }CASTER WHEEL
0017-00100-0037 |E-RING .375
0894-00702-O0XF |CASTER - WHEEL SHAFT
0961-00109-0000 | WHEEL BRKT.
14 B084-91877-AE68 |LAMP CONTROL P.C. BOARD ASSY.
15 0E36-00102-O0XF {MONITOR RAIL (2 REQ'D.) (BEHIND REAR WALL OF CABINET)
16 B084-91787-AE89 |8 TO 4 MULTIPLEX BD. ASSY.
17 B084-91870-A000 |FCC - FILTER BD. ASSY.: MONOBOARD
BEZEL MOUNTING BRKT. (2 REQ'D.) (BEHINO REAR WALL OF CABINET) | 18 | 0311-00100-0000 ADDITIONAL PARTS LiST (089-00300-0000 | CATALOG: STAR GUARDS U.R. - 3 PLAYER M051-00E89-A007 | TAG: OPTION SWITCH SETTINGS
AE36-00009-0000 |REAR DOOR ASSY. (INCLUDES FOLLOWING 6 ITEMS)
0£36-00502-0000 |REAR DOOR (WOOD)
0017-00009-0490 |VENT GRILLE - 5-5/8 SQ. IN. (2 REQ'D.) | 0017-00005-0050 |000R LOCK W/2 INDIVIDUAL KEYS 0017-00005-0209 |LOCK PLATE (SCREW MTD.)
_{ 90618-00117 coxe PERFORATED VENT GRILLE (2 REQ'D.) 0639-00116-OOXF |CAM: OFFSET 30 DEGREES
2-8
HEADER FLUORESCENT LIGHT ASSY.-PARTS LIST | PART NO. A595-00011-0000
TO ORDER BY PART NUMBER ONLY
PART NO. DESCRIPTION
0595-00105-0000 [FLUORESCENT BRKT.
0017-00003-0043 {18" COOL WHITE FLUORESCENT LAMP
0017-00003-0445 {LAMP LOCKS (2 REQ'D.)
0017-00031-0036 {FLUORESCENT SOCKET (2 REQ‘D.)
0017-00003-0412 {FLUORESCENT STARTER HOLDER W/LEADS
On, Dolo |e X 1/2 PHIL. RND. HD. M.S. (4 REQ'D.) 0017-00003-0019 FLUORESCENT STARTER 0017-00003-0026 TeaLLast 0017-00101-0598 | #8-32 X 5/16 SLT. HEX HD. SCR. (4 REQ'D.)
2-9
JOYSTICK ASSY! SHAFT & PLATE
PART NO. AE36-0002 1-0000
Reversible Ball Handle Activator
Satety Chamber
Safety Chamber ‘Safety Chamber
Recess Recess
Steet Shatt
Surlace for 8-Way we Reversibie Joystick ~~ \ a L- Surface lor 4-Way oy Joystick
Electronic 4/8-Way Joystick Assembly
Shaft w Ball (Bally Sente Part No 0017-00009-0645)
Piale w. Switches (Baily Sente Part No 0017-00009-0686)
COIN DOOR W/CABLE: BLACK 3-CHUTE PART NO. A982-00014-0021
FRONT VIEW
© NOT SHOWN
COIN DOOR W/CABLE: BLACK 3-CHUTE PART NO. A982-00014-0021
hw, @ on
© @ @ > ® © @ © TOP VIEW.
BOTTOM VIEW % NOT SHOWN
COIN DOOR W/CABLE: BLACK 3-CHUTE - PARTS LIST PART NO. A982-00014-0021 ORDER FROM COIN MECHANISM BY PART NUMBER ONLY (312) 279-9150
co 8S-8000-7 DESCRIPTION LARGE DOOR: 3 SLOT COIN RETURN CUP DOOR (3 REQ'D.) COIN RETURN CUP BEZEL (3 REQ'D.) COIN ENTRY CASTING (3 REQ'D.) COIN INSERT PLATE (3 REQ'D.) DENOMINATION INSERT (3 REQ'D.) REJECT BUTTON RETURN SPRING (3 REQ'D.) 8 | 7300-105 “C" WASHER (3 REQ'D.) 7800-11-RED REJECT BUTTON - RED A780-12-RED REJECT BUTTON HOUSING (RED) |
| 11 | 7800-11-AMBER | [REJECT BUTTON - AMBER | | |
| 12 | A780-12-AMBER | |REJECT BUTTON HOUSING (AMBER) | | |
13 | 7800-11-BLUE |REJECT BUTTON - BLUE
| 14 | a780-12-BLUE | [REJECT BUTTON HOUSING (BLUE) | | |
15 | 8000-22 WASHER 3/8 0.D. (3 REQ'D.) 16 | 8000-24-12 12V WEDGE LAMP (3 REQ‘D.) [7 8000-23 WEDGE LAMP SOCKET (3 REQ‘D.) 18 | 8000-14 HOUSING RETAINING BRKT. (3 REQ'D.) [1 8000-9 COIN ENTRY CHUTE (3 REQ'D.) 20 | 3300-34 “C" WASHER (3 REQ'D.) 21 | 8000-21 REJECT LEVER ASSY. (3 REQ'D.) 22 | 7800-14 TORSION SPRING (3 REQ'D.) 23 | 7600-141-1 MECH. RETAINING BRKT. (3 REQ'D.) 24 | 216-6-4 6-32 X 1/4 PHILLIPS PAN HEAD SCREW (27 REQ'D.) 25 | 606-110-N TNYLON WASHER (3 REQ'D.)
2-13
COIN DOOR W/CABLE: BLACK 3~CHUTE - PARTS LIST, CONT'D. PART NO. A982-00014-0021 ORDER FROM COIN MECHANISM BY PART NUMBER ONLY (312) 279-9150
PART WO. DESCRIPTION
0017-00005-0003 |COIN ACCEPTOR W/STRING CUTTER (3 REQ'D.) OR
0017-00005-0214 |COIN ACCEPTOR W/STRING CUTTER
404-4 4-40 HEX NUT (6 REQ'D.)
8000-10 MECH. MTG. BRACKET “STAKED" (3 REQ'D.)
7300-134
7300-100-1
8000-19
101-4-16
8800-9-1-R SLAM SKITCH BRACKET
7800-42 SLAM SWITCH
100-4-6 4-36 X 3/8 ROUNO HEAD MACHINE SCREW (3 REQ'D.)
8800-24 DBL. BTD. LOCK & KEY W/NUTS X615 [exis CAM 7800-7 KEY HOOK
0017-00007-0019 {KEY HOOK
A090-90089-0000 COIN METER ASSY. W/DIODE
A982-00015-0011 |COIN DOOR CABLE ASSY.
0017-00009-0609 | GROUND STRAP: L = 7" W/BLACK COVER tTLitlt 0017-00103-0061 |NUT: 8-32 HEX W/SEMS ST. (2 REQ'D.)
47 * | 0017-00103-0084 |NUT: 6-32 HEX W/SEMS ST. (2 REQ'D.) a 48 * | 0017-00104-0019 |WASHER: 6 145 - .375 - 032 FLAT ST.
- NOT PART OF ABOVE ASSEMBLY & MUST BE jpeneneh SEPARATELY, THROUGH BALLY MIOWAY MFG. CQ.
2-14
POWER CHASSIS: 130VA (SWITCHING) PART NO. A945-00059-0200
2-15]
POWER CHASSIS: 130VA (SWITCHING) PARTS LIST PART NO. A945-00059-0200
ORDER BY PART NUMBER ONLY
DESCRIPTION
CHASSIS SUB-ASSEMBLY
POWER SUPPLY COVER
8 X 4 UNSLOT HEX HD. SCREW (8 REQ'D.)
SWITCHING POWER SUPPLY - 125VA
0017-00042-0663 [LOCKING P.C. BRD. SPACER (4 REQ'D) | 5 | 0540-00138-2100 0017-00101-0134
} 8 | MT00-00136-A000 0017-00103-0061 CABLE PROTECTOR - 5"
6-32 X 4 PHIL. ROUND HD. SCREW
ISOLATION TRANSFORMER W/O SHIELD ASSY.-115V., 50/60 HZ.
8-32 HEX NUT W/SEMS (4 REQ'D) (NOT SHOKN)
0017-00003-0114 L15VAC (NOT SHOWN) LINE FILTER - 5 AMP,
6 X 6 PHL. PAN HO. (2 REQ'D) 0017-00101-0067
0017 -00003-0433 0017-00003-0263 ‘|ruse MOA, 3AG, 4 AMP, 115 VAC FUSE HOLDER
A945-00030-0600 a & CABLE ASSEMBLY 0017-00021-0370 {TERMINAL STRIP 0017-00101-0140 ta-a0 X 5 PHL. PAN HD. SCREW (2 REQ'D)
0017-00009-0580 {CAPACITOR ALIGNMENT TOOL
0945-00912-0000 jADJ. TOOL HANDLE
ADOITIONAL PARTS LIST
115£-00001-0004 |VARISTOR-METAL OXIDE (UNDER CHASSIS)
0017-00021-1110 {2 POSITION TERMINAL BARRIER STRIP (UNDER CHASSIS}
0017-00101-0780 6 X 8 PHIL. PAN HD. SCREW (UNDER CHASSIS)
0017-00103-0084 6-32 HEX NUT W/SEMS (UNDER CHASSIS)
2-16
SECTION 3
COMPONENT LAYOUTS, SCHEMATICS & WIRING DIAGRAM
20v/DIV 20 uSEC/DIV
1VIDIV.0.2MSEC/DIV TYPICAL OSCILLOSCOPE WAVEFORM PATTERNS
The waveforms shown below were observed on a wide band oscilloscope. The input signal was from a crosshatch generator with a horizontal sync frequency of 15.73kHz and 4 vertical frequency of 60 Hz. If the waveforms are observed on an oscilloscope with 4 limited high frequency response, the corners of the pulses will tend to be more rounded than those shown, and the amplitude of any high frequency pulse will tend to be less. Each photograph is numbered. These numbers correspond to the circied numbers on the schematic diagrams. Photographs 12, 13, 14, 1 and 16 are of the red signal at various points along the red video channel. The waveforms at corresponding points along the green and blue video channels will look similar
| 2V/DIV | 20 uSEC/DIV | 2VIDIV | 10 uSEC/DIV | OSV/DIV | 20 uSEC/DIV | O.2V/DIV. | SMSEC/DIV |
| 10V/DIV. | SMSEC/DIV | 2V/DIV | 20 vSECIDIV | 1VIDIV | 20 uSEC/DIV | OSV/DIV | 10 uSEC/DIV |
"
1V/DIV. 0.2MSEC/DIV SV/DIV 20 uSEC/DIV OSVIOIV 20 uSEC/DIV
- 14,
1v/DIV. 0.2MSEC/DIV
| 2VviOtV | 0.2MSEC/DIV | 1VIDIV | 0.2MSEC/DIV |
TROUBLESHOOTING CHART
NO PICTURE SEE NOTE 4
PES) car FLAMENT LIT
YES. ‘CHECK FOR GATE | PULSEATICL | PIN 12,
‘CHECK ALONG VIDEO CHANNEL FROM VIDEO. INPUT AT PI TO VIDEO | OUTPUT TRANSISTORS [_ONNECK BOARD.
CHECK FOR GATE REFERTONO | PULSE OUTPUT HIGH VOLTAGE FROM IC2, PIN 12 CHART
CHECK FOR OPEN HORIZONTAL YOKE CIRCUIT. y REFEH TO SYNC. PROBLEMS, CHART,
SYNC PROBLEMS SEE NOTE 8
NO HOR. SYNC NO VERT. SYNC y NO VERT SYNC | HOR. SYNC OK
CHECK SYNC. AMPL CKT: a7 y L NO HIGH VOLTAGE
_ [CHECK B+ (2av) Eaeaat B+ creaTeR | OR ee CHECK AC THAN 190 VOC | BOARD, P202 PINS INPUT
CHECK FOR SHORTED | icq LOOK FOR CAUSE OF B+ REGULATOR IC4, PINS 1-4 SHORTED IC4: OVERLOAD SHORTED. | CONDITION, SHORTED 11 FOR EXAMPLE
USING VARIAC, DECREASE AC INPUT | TO ZERO. THEN SLOWLY INCREASE AC SUCH THAT Bs = 123 VDC. Ic4 ok
(CHECK FUSE: IF FUSE IS OPEN, CHECK FOR SHORTED HOROUT- PUT TRANSISTOR Qil AND SHORTED 8+ REGULATOR, 14.
MONITOR MONITOR STILL OPERATES DOES NOT OPERATE
‘CHECK WHETHER HOR. OS. CHECK REIRAGE CILLATOR IS OPERATING. IN CAPA CHECK WAVEFORM @ AND [3] TUNING CAPACI- IC 2, PINS 1,2.3.4 AND 16, TOR C36
y H.V. HOLD DOWN CIRCUIT IS PREVENTING MONI- TOR OPERATION AT NORMAL AC INPUT. CHECK FOR, FAULTY CONDITION CAUSING H.V. TO BE TOO HIGH EXAMPLE: C36 DECREASED IN VALUE.
——_V. CHECK HY HOLD DOWN CIRCUIT: D10, 012, C2,
VERTICAL SWEEP PROBLEMS SEE NOTE 8
y BRIGHT, THIN, NO, OR VERY WAV LINE AT LITTLE VERT CENTER OF CRT. CAL SWEEP.
‘CHECK HOR. SYNC INVERTER CKT Q6, aeee (CHECK FOR OPEN VERT CAL YOKE WINDINGS OR VERTICAL YOKE PATH. —V
cae —Y _ CHECK VERTICAL OSGI y tt
LATOR AND TRIGGER CTS. CHECK HOR, IC2,PINS 10, 1,.12AND 13. | AFC: C2, PINS 2 AND 3 | CHECK VERTICAL |, [OC aLoGaNG| _ | CHECK VERTICAL POSITION CKT, G2. CAPACITOR IVE AND: - 2 wean 50. fs PINS 7.8.9.0 & 11
TROUBLESHOOTING NOTES
- The troubleshooting chart mentions specific components to be checked. It is intended that the entire circuit associated with these components be checked.
2 This chart is a guide to servicing rather than a complete list of each component that could fail. Therefore, troubleshooting should not be \imited only to those components mentioned in the chart.
- It is always useful to begin checking a circuit by measuring the DC voltages and then comparing the measurements to those listed in the Typical DC Voltages chart.
4, The cutoff controls and drive controis on the neck board and the screen control at the bottom of the flyback transtormer have been preset at the factory. When servicing the monitor for a lack of video, do not adjust any of these controls unless it is suspected that the problem is a result of these controls having been tampered with. Otherwise do not adjust these controls; if they are so severely out of adjustment that there is a lack of video, then there is something malfunctioning.
- The Wells-Gardner Service Department does accept telephone calls for servicing assistance. Call 1-312-252-8220, between 7:00am and 3:30pm Central Time. Ask for the Service Department. The Service Departmentis closed during the first two weeks of July Telephone assistance is not available uring this period. Before calling, be sure to have available the model number of the monitor being serviced and the schematic diagram of the monitor being serviced.
- Replacement parts may be ordered from the Service Department between 7:00am and 4:30pm Central Time.
- All monitors are equipped with automatic degaussing coils which demagnetize the picture tube every time the monitors turned on after being off fora minimum of 20 minutes. Should any partof the chassis become magnetized it will be necessary to degauss the affected area with a manual degaussing coil. Move the coil slowly around the CRT ‘ace area and all surrounding metal parts. Then slowly withdraw for a distance of 6 feet before turning off.
- Horizontal vs. Vertical:
‘Some models have the picture tube mounted vertically rather than horizontally. That is, the picture tube is mounted in the frame such that the long dimension of the tube is up and down. Examples of this include (but are not limited to) Models 13K7851 and 19K7951. Other than the physical orientation of the picture tube, there is no electrical difference between these models and their horizontal counterparts. The same circuits, the vertical circuits, produce and control deflection along the short dimension of the tube in all models.
‘The same circuits, the horizontal circuits, produce and control deflection along the long dimension of the tube in all models. Therefore, wherever “vertical” appears in this manual or on the monitor, it refers to the short dimension of the picture tube; wherever “horizontal” appears, it refers to the long dimension of the picture tube.
¢ g i
% nig Sx I sex I 2, 22
* am 93 92" aNSvo Bex
63,22 i] in eae om as 1 §3. 2N3908 Bhx neh 23908 oan [2c as suse no [4 $18 nso] fnae +verT sync [5 4 Hoon, ‘+HOR SYNC La)
np
= VERT syne
HOR SYNC
l2ovac '50/60H2 ih
i 2N3904 Ree 100, ark aa cis 22 t
1sase
¢)
fre DEGAUSSING coIL Ria i
Ri
Rs 1K
Rae 1K RAC TORY. lap yusTleo 8 SeaLeo|
Rao IK
23904, Ror O7 tok
R08. ©) pe] || | i Me feaie
R20
ev,
34567869 10
K7000 COLOR MONITOR SCHEMATIC DIAGRAM
cu 2e,2sv
R21 R22] ‘sex $22)
Rea 1K CONTRAST vr By Tox
ciz 1, Sov. R26 8.2K 1a '2N3904, P44s
29.0mm NECK
ALTERNATE CRT AND NECK BOARD
I3K7800 SERIES ISK7600 SERIES R27 WSs bis 22k 1k
upcis97e
2221 2019 8 17 16 154 13 12 ae a L}i 8 O R29 254 oer TP 10K 8” | & 22 | ‘ove Tee vae Texguae [TT — pio 7°? tt CI BRIGHTNESS sev R37
OWN, BRM Noeov rt sae 20a Pe eat} 08 ca Be 0.05¥ ro,eav }/77 94, 08 Pca | Bek leon,vew a Ry | c29 [RONG
3 12 10 9| vas 500 POSITION HOR aio [ascdfeaz z 8)" "DRIVE c32 gree eK wre ee
100 Sars cas
27K
6. R201
eK 3.3K RIO!
R302 IS PRESENT ONLY ON 19K 7600 ANO 19K7900 SE~ RIES MONITORS. HORIZONTAL I9K7900 SERIES
ouTPUT REFER TO OTHER SCHEMATIC DIAGRAMS FOR CERTAIN UNIQUE MODELS Lt Notes
| ALL RESISTORS ARE IN OHMS.1/4W,5% UN- LESS OTHERWISE INDICATED.
2 CAPACITANCE VALUES LESS THAN I ARE IN WICROFARADS. ABOVE | IN PICOFARADS UN- ‘SS OTHERWISE INDICATED.
- CIRCLED NUMBERS INDICATE LOCATIONS OF CERTAIN WAVEFORM READINGS.
+24v
Ree 2.2K IW
VERTICAL, POSITION
‘SIZE 50-60Hz
ALTERNATE CIRCUIT FOR
RIO? LATER PRODUCTION
VERTICAL os size ADuUST, REO 2.261"
Le. LINEARITY AM CAUTION sarery ceiticac component
REPLACE ONLY WITH SAME TYPE PARTS AS SHOWNIN PARTS LIST. Crry ‘47K
Reo
WARNINGS
- Power Up Warning- ‘An isolation transformer must be used between the AC supply and the AC plug of the monitor before servicing, testing, or operating the monitor since the chassis and the heat sink are directly connected to one side Of the AC line which could present a shock hazard, Before servicing is performed, read all the precautions labelled on the CRT and chassis.
2.|__ X-RAY RADIATION WARNING NOTICE
- High Voltage- This monitor contains HIGH VOLTAGES denved from power supplies capable of delivering LETHAL quantities of energy. Do not attempt to service until ali precautions necessary for working on HIGH VOLTAGE equipment have bean observed
- CRT Handling- Care must be taken not to bump or scratch the picture tube as this may cause the picture tube to implode resulting in personal injury. Shatter proof goggles must be worn when handling the CRT. High voltage must be completely discharged before randling, Do not handle the CRT by the neck
5.|_ PRODUCT SAFETY NOTICE
For replacement purposes, use the same type or specified type of wire and cable, assuring the positioning of the wires is, followed (especially for HV. and power supply circuits). Use of alternative wiring cr positioning could result in damage to the monitor or in a shock or fire hazard.
VIDEO INTERFACE AND OUTPUT The red, green, and blue video inputs come into the monitor at P1. Isolation and attenuation is provided by emitter followers Qt, Q2 and Q3. Forced blanking of the video signals is provided by the circuit of Q4, D5, D6, and D7. The forced blanking causes there to be an interruption in the video signal before it goes to the inputs of IC1. This interruption occurs between scan periods, while retrace is taking place; it is required by IC1. The forced blanking is not necessary for most video signals since they already have an interruption of video (blanking) between scan periods. Some do not; it is to accommodate such signals that the forced blanking circuit is included.
The red, green, and blue signals go into |C1 at pins 2, 4, and
- Their levels are controlled by the gain of separate channels of the contrast amplifier. The gain is controlled by a DC voltage input to pin 11, which varies with the setting of the contrast control. IC1 provides blanking of the video during retrace in response to blanking pulses at pin 13, derived from the horizontal and vertical sweep circuits. IC1 also requires a gating signal at pin 12 in order to provide red, green, and blue outputs at pins 21, 19, and 17. If the gating signal is not present, C1 will not provide video output signals. The gating signal comes from IC 2, pin 12 and is derived from horizontal sync. The brightness is varied by varying the DC level of the outputs at pins 17, 19, and 21. This is accomplished by varying the DC voltage input to pin 14. The video outputs from IC1 are provided via R30, R31, and R32 to the neck board where they are amplified by the video output stages Q201, Q202, and Q203 before being applied to the cathodes of the CRT through R10, R11, and R12.
SYNC Sync is applied at P1 (positive sync) or at P2 (negative sync). Composite sync should be applied only to the horizontal sync input of the appropriate polarity. Positive sync is inverted by Q5 and G6 then applied through D3, D4 and R51 to the sync amplifier Q7. The sync amplifier output is applied through C22, R53, and R55 to pin 14 of IC2. Pin 14 is the sync separation input.
The sync separator extracts the horizontal and vertical sync from each other—providing horizonta! sync to the horizontal AFC circuit in the IC. A composite sync output is provided at pin 12. This output signal is used for gating IC1 the video interface IC and for triggering the vertical oscillator. HORIZONTAL OSCILLATOR AND OUTPUT The horizontai AFC circuit of C2 receives a horizontal sync input from the sync separator and a feedback signal at pin 1, derived from the horizontal output. Slight differences in frequency and phase of the two signals will cause the AFC. to generate a correction voitage at pin 2. The horizontal oscillator in|C2 has its free running frequency determined by the RC time constant of C19, R56, R57, R58, and VR2, the horizontal hold control. The horizontal hold control varies the horizontal frequency by varying the RC time constant. Slight correction in frequency is provided by a correction voltage at IC2, pin 3 which comes from pin 2 through R60. The oscillator output at pin 4 is amplified and shaped by the horizontal drive stage Q10. The drive signal is then coupled to the base circuit of the horizontal output transistor Q11 by the horizontal drive transformer T2.T2is used for impedance transformation to provide the Q11 base circuit with the low impedance source that it requires. The horizontal output transistor Q11 is operated as a switch. It is either on or off. It is turned on and off at the scan rate which is determined by the horizontal oscillator frequency which is ultimately determined by the incoming horizontal sync frequency. A yoke current with a sawtooth waveform is needed to deflect the beam linearly across the CRT. The beam begins at the center of the CRT and is deflected from center to right. This center-to-right deflection occurs when Q11 is turned on. The deflection yoke coupling capacitor C38, also known as the S-shaping capacitor, begins to discharge through the yoke; the discharge current causes the beam to be deflected to the right CRT edge. At this time, Q11 is turned off, and the current provided by C38 stops. As the current falls to zero, a voltage is induced across the yoke windings as the magnetic field collapses; an oscillation is produced by the yoke windings and C36, the retrace tuning capacitor. During the first half cycle of oscillation, the induced voltage is impressed on the collector of Q11, C36, and the primary of they flyback transformer T1. This induced voltage is stepped up by the flyback transformers secondary winding. This high voltage is then rectified and applied to the high voltage anode of the CRT. When this induced voltage occurs, the electron beam is deflected from the right edge of the CRT face to the left edge. This is calied retrace. During the second half cycle of the oscillation (of C36 and the yoke windings), the voltage at the Q11 collector tries to go negative or below ground. When this happens, the damper diode (include in same package with Q11) becomes forward biased. The conduction of the damper diode allows energy Stored in the horizontal system to decay linearly to zero, thus allowing the beam to return to the center of the CRT face. The focus voitage and the screen, G2, voltage are obtained from the anode voltage with a resistor divider network within the T1 assembly. An auxiliary winding (pin 10) provides feedback.to the horizontal AFC through R71, R70, and C29. This signa\ is also used to furnish the horizontal blanking input to IC1 via C28, R69, and R68. The signal from the auxiliary winding at pin 5 of T1 is rectified by D14 and filtered to provide the +12VDC supply for the video interface and sync circuits. The auxiliary winding of pins 3 and 4 produces a signal which is rectified by 013 and filtered to produce the +24VDC supply for the vertical output circuit. The horizontal linearity coil L2 is a magnetically biased coil which shapes the yoke current for optimum linearity. The horizontal size coil L1 is a variable series inductor which is used to vary the horizontal size of the display.
HIGH VOLTAGE HOLD-DOWN CIRCUIT The high voltage hold down circuit is part of the main PC board P447 of this monitor. The +12V DC supply is sensed via D10. Since the +12V DC supply is flyback pulse derived, the +12V DC supply will rise as the high voltage rises. If the +12V DC exceeds a threshold which is set with VR8, then D12 will conduct, thereby providing drive to IC2, pin 5holddown input of deflection oscillator IC. The drive being applied to pin 5 causes the horizontal oscillator within the IC to shut down-thus preventing the generation of high voltage. The horizontal oscillator will remain in its OFF state, even if the input to IC2, pin 5 is removed, unless and until AC power is removed from the monitor input. The power may then be reapplied.
VERTICAL OSCILLATOR AND OUTPUT The composite sync ouput of IC2, pin 12 is filtered through the network of R65, C25, C24 and R66 so that only vertical sync is applied to the vertical trigger input at pin11. The vertical oscillator frequency is controlled by the vertical hold control and its input to pin 10.
The vertical drive output at IC2, pin 7 is applied to pin 4 of IC3, the vertical output IC. Output current from IC3, pin 2 flows through the yoke to cause vertical deflection. During upward deflection, current flows out of pin 2, through the yoke, and into C50 to charge it. Downward deflection is caused by C50 discharging through the yoke in the opposite direction and back into IC3, pin 2. AC feedback is provided through the wiper of the vertical size control VR4 to |C2, pin 8 inorder to control the drive amplitude. DC feedback at!C2, pin 9 maintains good vertical linearity at all sizes. DC current from the +24V supply flows through R83 and through the yoke to provide downward raster shift. Some of this DC current is diverted from the yoke through the collector of Q9. The amount of this current which is diverted from the yoke can be varied by varying the base drive to QQ by adjusting VR3, the vertical position control, thus providing manual adjustment of the vertical position of the display. The drive signal at IC3, pin 2 is also used to furnish the vertical blanking input to IC1, pin 13 via R63 and C14.
AUTOMATIC DEGAUSSING ADG The ADG circuit automatically demagnetizes the CRT. This circuit is activated only when the monitor is initially powered up after having been off for at least 20 minutes. R108 is a positive temperature coefficient device. When it is cold, it has a very low resistance. As it gets warm, its resistance increases. If the monitor is cold when AC power is applied, then R105 with a low resistance allows current to pass through it, D23, D24, and the degaussing coil. As current flows through R106, it heats up and eventually has a very high resistance, allowing very little current to flow through it. The residual current now flowing through R105 produces a voltage drop across R104 of less than 0.6 volts. This is not enough to forward bias D23 and D24, so there is no current through the degaussing coil. The process of initially having a large current through the degaussing coil and then having the current decay to zero is what produces the degaussing action. The degaussing current decays to zero before the CRT warms up, so the degaussing is completed before the picture comes on.
GENERAL REPLACEMENT PARTS LIST For all K7000 models except where noted.
for safety purposes. This monitor contains circuits and components included specifically For continued protection no changes should be made to the original design, and components shown in shaded areas of schematic, or A * on parts list should be replaced with exact factory replacement parts. The use of substitute parts may create a shock, fire, radiation or other hazard. Service should be performed by qualified personnel only. P447 MAIN BOARD (CONT.)
P447 MAIN BOARD
| Ret. No. | Part No. | Description | Ret. No. | rt No. | Description |
RESISTORS RESISTORS (Cont.)
| Rt | 340X2562-934 | 5.6K Ohm 5% 0.25W | R59 | 340x2103-934 | 10K Ohm 5% 0.25W |
| R2 | 340X2562-934 | 5.6K Ohm 5% 0.25W | REO | 340X2563-934 | 56K Ohm 5% 0.25W |
| R3 | 340X2562-934 | 5.6K Ohm 5% 0.25W | R61 | 340X2332-934 | 3.3K Ohm 5% 0.25W |
| Ra | '340X2472-934 | 4.7K Ohm 5% 0.25W | R62 | 340X2122-934 | 1.2K Ohm 5% 0.25W |
| RS | 340X2472-934 | 4.7K Ohm 5% 0.25W | R63 | 340X2563-934 | 56K Ohm 5% 0.25W |
| R6 | 340X2472-034 | 4.7K Ohm 5% 0.25W | R64 | 340X2184-934 | 180K Ohn 5% 0.25W |
| R7 | 340X2333-934 | 33K Ohm 5% 0.25, | Res | 340X2123-934 | 12K Ohm 5% 0.25W |
| RB | 340X2333-934 | 33K Ohm 5% 0.25 | R66 | 340X2224-934 | 220K Ohm 5% 0.25W |
| RO | 340X2333-934 | 33K Ohm 5% 0.25 | R67 | 340X2623-934 | 62K Ohm 5% 0.25W |
| R10 | 340X2151-934 | 150 Ohm 5% 0.25W | Res | 340X2223-934 | 22K Ohm 5% 0.25W |
| R11 | 340X2151-934 | 150 Ohm 5% 0.25W | R69 | 340X3683-231 | 68K 5% 0.5W CAR |
| R12 | 340X2151-934 | 150 Ohm 5% 0.25W | R70 | 340X2682-934 | 6.8K Ohm 5% 0.25 |
| R13 | 340X2102-934 | 1.0K Ohm 5% 0.25W | R71 | 340X3473-234 | 47K 5% 0.5W |
| Rig | 340X2102-934 | 1.0K Ohm 5% 0.25W | R72 | 340X2101-934 | 100 Ohm 5% 0.25W |
| R15 | 340X2102-934 | 1.0K Ohm 5% 0.25W | R73 | 340X2103-934 | 40K Ohm 5% 0.25W |
| R16 | 340X2822-934 | 8.2K Ohm 5% 0.25W | R74 | 340X2220-934 | 22. Ohm 5% 0.25W |
| RI7 | 340X2822-934 | 8.2k Ohm 5% 0.25W | R75 | 340X2222-934 | 2.2K Ohm 5% 0.25W |
| R18 | 340X2152-934 | 1.5K Ohm 5% 0.25w | R76 | 340X2473-934 | 47K Ohm 5% 0.25W |
| R19 | 340X2103-934 | 40K Ohm 5% 0.25W | RI7 | 340X2333-934 | 33K Ohm 5% 0.25 |
| R20 | 340X2102-934 | 1.0K Ohm 5% 0.25W | R78 | 340X2102-934 | 1.0K Ohm 5% 0.25W |
| R21 | 340X2563-934 | 56K Ohm 5% 0.25W | R80 | 340X3056-934 | 5.6 5% 0.5W |
| R22 | 340X2562-934 | 5.6K Ohm 5% 0.25W | R81 | 340X2150-934 | 15 Ohm 5% 0.25W |
| R23 | 340X2102-934 | 4.0K Ohm 5% 0.25W | Re2 | 340X3821-934 | 820 Ohm 5% 0.5W |
| R24 | 340X2224-934 | 220K Ohm 5% 0.25W | R83 | 340X3681-934 | 680 Ohm 5% 0.5W |
| R25 | 340X2273-934 | 27K Ohm 5% 0.25W | Red | 340X2682-934 | 6.8K Ohm 5% 0.25 |
| R26 | 340X2822-934 | 8.2K Ohm 5% 0.25W | R85 | 340X2332-934 | 3.3K Ohm 5% 0.25W |
| R27 | 340X2223-034 | 22K Ohm 5% 0.25W | R86 | 340X2224-934 | 220K Ohm 5% 0.25W |
| R28 | 340X2332-934 | 3.3K Ohm 5% 0.25W | R87 | 340x2334-844 | ‘330K 10% 0.5W |
| R29 | 340X2103-934 | 40K Ohm 5% 0.25W | R88 | 340X4 182-633 | 1.8K 5% 1W |
| R30 | '340X2101-934 | 100 Ohm 5% 0.25W | REO | 043X0476-002 | 3.9K 5% 5W MO |
| R31 | 340X2101-934 | 100 Ohm 5% 0.25W | R90 | 043x0486-002 | 1.2 5% 2W ME |
| R32 | 340X2101-934 | 100 Ohm 5% 0.25W | R91 | 043Xx0486-002 | 1.2 5% 2W MF |
| R33 | 340X2102-934 | 1.0K Ohm 5% 0.25W | R92 | 043Xx0486-002 | 1.25% 2W ME |
| R34 | 340X2102-934 | 1.0K Ohm 5% 0.25W | R93 | 420X5102-324 | 1.0K 5% 2w |
| R35 | 340X2102-934 | 1.0K Ohm 5% 0.25W | Roa | 340X2473-934 | 47K Ohm 5% 0.25W |
| R36 | 340X2122-934 | 1.2K Ohm 5% 0.25W | RO5 | 340X2473-934 | 47K Ohm 5% 0.25w |
| R37 | 340X2822-934 | 8.2K Ohm 5% 0.25W | RO6 | 420X6182-325 | 1.8K Ohm 5% 3W, WW |
| R38 | 340X2122-934 | 1.2K Ohm 5% 0.25W | R97 | 420X627 1-325, | 270 5% 3W |
| R39 | 340X2122-934 | 1.2K Ohm 5% 0.25W | R98 | 340X4222-633 | 2.2K Ohm 5% 1W |
| R40 | 340X2102-934 | 1.0K Ohm 5% 0.25W | R99 | 340X4222-633 | 2.2K Ohm 5% 1W |
| Rat | 340X2102-934 | 1.0K Ohm 5% 0.25W | R100 | 340X4271-633, | 270 5% 1W |
| a2 | 340X2473-934 | 47K Ohm 5% 0.25W | R101 | 420X6682-325 | 6.8K 5% 3W |
| R43 | 340X2222-934 | 2.2K Ohm 5% 0.25W | R102 | 340X4470-633 | 47 5% 1W |
| R44 | 340X2 104-934 | 100K Ohm 5% 0.25W | AxR103 | 043x0483-001 | 2.7 Ohm 5% 7W |
| Ras | '340X2104-934 | 100K Ohm 5% 0.25W | R104 | 043X0484-001 | 15 Ohm 5% SW |
| R46 | 340X2101-934 | 100 Ohm 5% 0.25w | R105, | 043x0485-001 | Thermister |
| Ra7 | 340X2101-934 | 100 Ohm 5% 0.25W | R106 | 340X2273-934 | 27K Ohm 5% 0.25W |
| Rag | 340X2102-934 | 4.0K Ohm 5% 0.25W | R107 | 340X2102-934 | 1.0K Ohim 5% 0.25W |
| Rag | 340X2102-934 | 4.0K Ohm 5% 0.25W | R301 | 043x0481-003 | 220 Ohm 15W WW |
| R50 | 340X2103-934 | 10K Ohm 5% 0.25W | vat | 040X0653-002 | CTRL 500 |
| R51 | 340X2103-934 | 10K Ohm 5% 0.25W | vR2 | 040X0653-005 | CTRL 10K |
| R52 | '340X2102-934 | 4.0K Ohm_5% 0.25W | VR3 | 040X0653-005 | CTRL 10K |
| R53 | 340X2151-934 | 150 Ohm 5% 0.25W. | vR4 | 040X0653-001 | CTRL 200 |
| R54 | 340X2224-934 | 220K Ohm 5% 0.25W | VRS | 040X0653-006 | CTRL 200K |
| RSS | 340X2101-934 | 400 Ohm 5% 0.25W | VRE | 040X0653-003 | CTRL 2k |
| R56 | 340X2472-934 | 4.7K Ohm 5% 0.25W | VR7 | 040x0653-005 | CTRL10k |
| R57 | 340X2182-934 | 1.8K Onim 5% 0.25W | VRB | 040X0639-006 | Trim Pot 2K Ohm 0.3W |
| R58 | 340X2123-934 | 42K Ohm 5% 0.25W | vRg | 040X0655-001 | Trim Pot 200 Ohm |
FINAL ASSEMBLY PARTS
| Ref. No. | Part No. | Description |
13K7800 SERIES (13”)
| Ar | 88X0236-506 | CRT Orion A34JLLOOX |
| * | 942860-001 | Deflection Yoke |
2A0690-001 Purity & Convergence Ring Assembly 982856-001 Degaussing Coil Assembly 8X0378-001 Rubber Wedge 19K7600 and 19K7900 SERIES (19”)
| Ar | 88X0237-506 | CRT Philips MVA48ABKOSX |
| * | 942862-001 | Deflection Yoke |
2A0690-001 Purity & Convergence Ring Assembly 982857-001 Degaussing Coil Assembly 208X2400-901 Rubber Wedge
| Ret. No. | Part No | Description | Ret. No | Part No | Description |
CAPACITORS SEMICONDUCTORS
| c1 | 080x0099-671 | Disc 22PF 10% NPO | BB | Peed | Pete Nee | |
| c2 | (080X0099-671 | Disc 22PF 10% NPO | 2 | igBes0070-004 | Diode 1N9148 | |
| 3 | 080X0099-671 | Disc 22PF 10% NPO | ||||
| oa | 066X0070-001 | Diode 1N914B | ||||
| ca | 045x0577-501 | Elect 1OMF NP 25V | ba | Geeyo070-00t | Diode ING 148 | |
| cs | 045X0577-501 | Eiect 10MF NP 25V | 06 | Sees007 0.001 | Diode 1NB 148 | |
| ce | 045x0577-501 | Elect 10MF NP 25V | D6 | erneta | Diode twet4e) | |
| ¢ | Pe ie | AOE oe toe coy | 08 | 066x0070-001 | Diode 1N9148 | |
| ce | 047X0786-502 | MYR 022 10% 50V | be | Eade | Paap | |
| if | basocepeat | MYR ore oo | DI0 | 066X0070-001 | Diode 1N914B | |
| ig | pees | Elect SoMF 18y | on | 066x0040-028 | Zener Diode 5.1V 5% 0.5W | |
| a | sexe ee | Ae or co | D12 | 066X0040-005 | Zener Diode 10V 5% 0.5W | |
| or | pa | Tr oo | 013 | 066X0090-001 | D1 Fast SW RU-2 | |
| 13 | 045x0560-534 | Elect 22MF 25V | pe | pasxone a0 | Dt Bests Ae | |
| cia | 047x0786-502 | MYR 022 10% 50V | pis | baex080 001 | Oreo ave | |
| C15 | 047x0786-502 | MYR .022 10% 50V | xe | O66x0090.001 | bt paeteweue | |
| oe | oarnovee S01 | OyCuE Inco | DI7 | 066X0090-001 | D1 Fast SW RU-2 | |
| c17 | 047X0786-501 | O10UF 10% SOV P-Estr | on | Geexoogo-001 | Bose Sono GFETOR | |
| ee | Gaeeecoeoe | Pol dane a | A 019 | 066X009 1-001 | Diode SI 1A 600V | |
| ang | eee | trrore | A 020 | 086X0091-001 | Diode S! 1A 600V | |
| hess | OAeROSCO SIS | yn iouE 230 | A 021 | 066x0091-001 | Diode SI 1A 6000 | |
| 2 | Path | tyr QUES | A 022 | 066x0091-001 | Diode SI 14 600V | |
| &s | paexaseo ety | Cyr avOE sv. | 023 | 066X0091-001 | Diode S| 14 600V | |
| Se | parnareesee | AVA oe cov | 024 | 066X0091-001 | Diode S! 14 600V | |
| C24 | 047x0786-503 | MYR .068 10% SOV | p24 | Fool | Beare | |
| 25 | 047x0786-512 | P-Ester 015 10% 50V | De | ogaxonae-00} | Di Boost wso04 | |
| cee | oarroree aul | Ee | ia | a2 | 086X0113-501 | TASTR NPN 2N3904 |
| oar | 80K 0089 2. | Diao 220 10% Z6r. | a3 | 086x01 13-501 | TRSTR NPN 2N3904 | |
| ca8 | Gen Xo0es O48; | SEF 20% 2KV NFO: | a4 | 086x0113-501 | TRSTR NPN 2N3904 | |
| C29 | 047X0786-501 | O10UF 10% SOV P-Estr | os | rth eeo | ah aly | |
| 30 | 080X0099-505, | Disc 001 20% Z5F 500V | os | osexor13 501 | Taste NEN 2NSoO4 | |
| 31 | 047X0786-501 | O10UF 10% SOV P-Estr | ee | coax 1201 | angry wen aNagee | |
| C32 | 080X0099-580 | Disc 100 10% Z5F S00V | g | coete Tg S5} | TRSTR NEN 2N3904 | |
| 33 | (080x0099-722 | Disc .0033 10% YSP 500V | 4 | opaxo 119901 | TRSTR NEN 2N3004 | |
| C34 | 080X0099-221 | Disc 01 10% YSP 500V | e | peared | Teer en aN | |
| 35 | 047x0786-501 | O10UF 10% SOV P-Estr | gre | pert ert | Meet ee | |
| aces | 4 6n03) 008 | PF 6100 2% 1500v | Ic1 | 086X0186-001 | IC Video UPC 1397 NEC | |
| es | Caer ON 006 | 15 100y Fr | 1c2 | 086x0 187-001 | IC Hon Vert LA7823 | |
| bait | Oaecpeenone | SSUF Ste 200V PP | 1c | 086X0 189-001 | IC Vert Output UPC 1378 | |
| Koi | bsoxcbeoeee | Bact 2200/36V | Anica | 086X0 188-001 | Regulator IC STR3123 | |
| cat | 080X0099-505 | Disc 001 20% Z5F S00V | ||||
| 42 | 045X0560-006 | LYT 1000UF 16v | ||||
| 43 | 080x0099-505 | Disc 001 20% Z5F S00V | ||||
| 44 | o46x0584-009 | 130% 100V P-Prop | TRANSFORMERS AND COILS |
LyT 470uF
| cae | Dasxoseo.o20 | © | LYT 470UF tev | au | 009A2854-001 | Coll Width-TODA |
| ca7 | 080x0099-580 | Disc 100 10% 25F 500V | we | 009A2855-001 | ey eRbecn | |
| caa | 045X0560-532 | Elect 100MF 35V | Ast | 053X0528-001 | ranst Flybac| | |
| vag | 047X0786-501 | OOUF 10% SOV P-Estr | 12 | 052X0131-001 | Transf-Horiz Driver | |
| cs50 | 045x0560-023 | LYT 1000UF 25V | ||||
| 51 | 045X0525-512 | Tan 68 10% 35V | ||||
| 52 | 047x0786-501 | O10UF 108 SOV P-Estr | ||||
| 53 | 047x0786-514 | O33UF 5% SOV P-Estr | ||||
| Cea | 047x0786515 | MYR_022 5% SOV | MISCELLANEOUS | |||
| C55 | 045X0578-001 | Elect 560 200V | AF | 016x0176-001 | Fuse 1.5A SB | |
| 56 | 045x0569-008 | LYT 22UF 160V | 016x0182-001 | Fuse Clip | ||
| cs7 | (045X0569-011 | Elect 47 160¥ | Pt | 006a0428-001 | Plug Header | |
| a cs9 | 080X0099-724 | Disc 0015 10% Y5P 500V | P2 | 006A0428-001 | Plug Header | |
| 60 | 080x0099-723 | Disc 0022 10% Y5P 500V | P3 | 00640427-001 | Plug 2 Pin | |
| A C61 | 080X0099-723 | Disc 0022 10% Y5P 500V | Pa | 006A0406-001 | Plug 4-Pin OSHIMA | |
| A coz | 046X0552-001 | + 20% 125VAC | P6 | 00640429-005, | Plug Header | |
| 63 | 047X0786-501 | O10UF 10% SOV P-Estr | 1202 | 018x1243-001 | Cable Assy 4 Wire 350mm |
P456 NECK BOARD (used with CRT’s with a 22.5mm neck diameter) RESISTORS CAPACITORS
| R201 | 340X2272-934 | Res 2.7K Ohm 5% 0.25W | 201 | 080x0090-006 | Cap 470PF 10% Z5F CER |
| R202 | 340X2151-934 | Res 180 Ohm 5% 0.25W | 202 | 080X0099-006 | Cap 470PF 10% Z5F CER |
| 203 | 340X2272-934 | Res 2.7K Ohm 5% 0.25W | €203 | 080X0099-006 | Cap 470PF 10% Z5F CER |
| R208 | 340X2151-934 | Res 150 Ohm 52% 0.25W | 204 | 080x0099-221 | € Disc 01 10% Y5P 500V |
| R205 | 340x2272-934 | Res 2.7K Ohm 5% 0.25W | 208 | 080X0099-225 | € Disc 0015 1.5KV |
| R206 | 340X2151-934 | Res 150 Ohm 5% 0.25W | |||
| R207 | 340X5682-633 | Res 68K 2W MO | |||
| R208 | 340X5682-633 | Res 6.8K 2W Mo | SEMICONDUCTORS | ||
| R209 | 340X5682-633 | Res 68K 2W Mi | eet | ||
| R210 | 340x3272-244 | Res 27K Ohm 10h 05W | 202 | QeeKote4oo1 © | TRSTR 28¢2068LB/LBBK |
| Big | Bie | Bes 27 Ohm 10n Oe | 203 | 086X0184-001 | TRSTR 28C2068L8/LBBK |
| R212 | 340X3272-244 | Res 27K Ohm 10% 0.5W | |||
| R213 | 340X5689-333 | Res 68 Ohm 5% 2W | |||
| vR201 | 040X0653-003 | CTRL 2k | |||
| vR202 | 040x0853-001 | CTRL 200 | MISCELLANEOUS | ||
| vR203 | 040X0653-003 | CTAL 2k | 202 | 006A0429-005 | Plug Header |
| vR204 | ‘040X0653-001 | CTRL 200 | SKT201 | 003A0636-007 | Pix Socket |
| VR205 | 040X0653-003 | CTRL 2k | Js | 013x1243-001 | Cable Assy 4 Wire 350mm |
| vR206 | 040X0653-001 | CTRL 200 | 030X0797-001 | Plug V Pin |
P448 NECK BOARD (Used with CRT’s with a 29mm neck diameter) Same as P456 NECK BOARD except: SKT201 003A0651-001 SOC CRT
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
CROSS REFERENCE LIST: CROSS REFERENCE LIST: MONOBOARD A084~91787-F000 051-00114-F156
See Rom/Eprom Chart
| DESCRIPTION | QTY | DESIGNATION No. | PART NO. | DESCRIPTION | QTY © DESIGNATION NO. | PART NO. | |
| 18 PF AX. CER. | 4 | 60,C62,C67,068 | 0A15-00800-0011 | 74F00 | 1 | Iclr | 0A59-00803-0001 |
| 33 PF AX. CER. | 2 | ,c65 | 0986-00800-0300 | 74F04 | 1 | ol | 0A59-00803-0034 |
| 47 PP AX. CER. | 6 | c47-c52 | 0986-o0800-2800 | «-74F08 | 1 | Ic 14K | 0a59-00803-0030 |
| 68 PF AX. CER. | 3 | 057,C63,C64 | 0360-00800-0028 | 74710 | 1 | IC 9E | 0a59-00803-0002 |
| 270 PF AK. CER. | 2 | 069,C70 | OA15-00800-0013 | 74F74 | 2 | IC 28,108 | 0A59-00803-0003 |
| 390 PF AX. CER. | 5 | ¢1,C2,C42,042,C55 | 0986-00800-3000 | 74F86 | 2 | Ic 10F,7H | 0A59-00803-0032 |
| 820 PF AX. CER. | 4 | C43-C46 | 0945-00816-0400 | 74F157 | 4 | IC 5¢C,6C,8C,66 | 0A59-00803-0004 |
| -O1 UF AX. CER. | 146 = CP1-CP65,C67-C142 | 0986-09800-2000 | T4E174 | 2 | Ic 8D, 2H | 0as9-00803-0005 |
C40 ,C58 C59, C61 ,C66
| 1 UF AX. CER. | 33° | 6-C38 | 0986-00800-1100 | 74LS00 | 2 | IC 14a,6F | 0304-00803~-0010 |
| 10 UF 25V AX. TANT. | 2 | 4,039 | 0986-00800-0700 | 74LS02 | 1 | IC Ww | 0986~00803-7400 |
| 47 UF 25V RD TANT | 1 | oO | 0A59-00800-0001 | 74LS08 | 2 | Ic 1G,4H | 0986-00803-7300 |
| 100 UF 16V RD TANT | 1 | (66 | 0945-00811-0500 | _74LS20 | 3. | IC 2,3F,12H | 0986-00803-1004 |
| 470 UF 16V AX. ELEC. | 3 | €3,C53,054 | 0986-00800-2709 | _74LS32 | 4 | IC 5F,18,4K,1A | 0986-00803-6100 |
| T4LS55 | 1 | iIcw | 0a59-00803-0026 | ||||
| 10 OFM 1/4W 5% CRBN. | 6 — R58,R59,R61,R62,R64, | 100E-00005-0011 | T4LS74 | 6 | IC 12E,15F,3K,5K,6K, — 0986-00803-1005 | ||
| R65 | : | 15K | |||||
| 22 OHM 1/4W 5% CRBN. | 1 | R48 | 100E~00005-0016 | TALS86 | 2 | IC 13¢,8H | 0986-00803-9900 |
| 47 Of 1/4W 5% CRBN. | 4° | R88-R90,R93 | 100E-00005-0025 | 741138 | 2 | IC 108,26 | 0986-00803-6500 |
| 68 OHM 1/4W 5% CRBN. | 4 — R50,R51,R91,R92 | 100£-00005-0029 | 7418153 | 2 | Ic 14¢c,15D | A59-00803-0006 | |
| 82 OHM 1/4W 5% CRBN. | 7 | R9,R80,R87,R96,R97, | 100E-00005-0031 | _74LS157 | 6 | IC 5A,3C,7C,7D,11D,3G 0304-00803-0021 | |
| RLOO,R102 | 74LS161 | 1 | cla | 0986-00803-1003 | |||
| 220 O&M 1/40 5% CRBN. | 32 © RL4-RAS. | 100E-00005-0041 | 74LS163 | 3. | IC 3D-5D | 0A59-00803-0008 | |
| 470 OFM 1/4W 5% CRBN. | 3 | R60,R63,R66 | 100E-00005-0051 | TALS169 | 4 | IC 9G,10G,7K,9K | 0304-00803-0023 |
| 510 OHM 1/4W 5% CRBN. | 3 | R69,R72,R76 | 100E-00005-0053 | TALS173 | 1 | Ice | 0A59-00803-0009 |
| 560 OHM 1/4W 53 CRBN. = 3. | R57, R77,R78 | 100E-00005-0054 | 74LS174 | 3. | IC 12D,14H,13K | 0304-00803-0024 | |
| 680 OFM 1/40 5% CRBN. | 4 «R94, RI5,ROB,RID | 100E-00005~-0056 | TALS175 | 1 | ome4s | 0304-00803-0025 | |
| 1K OM 1/4W 5% CRAN. | 5 | R68,R71,R73,R75,R86 | 100E-00005-0061 | 74LS194 | 8 | IC 13D,11E,13E,14E, — 0304-00803-0026 | |
| 2K OHM 1/4W 5% CRBN. | 3 | R67,R70,R74 | 100E-00005-0068 | 12F-14F,14G | |||
| 2.7K OHM 1/4W 5% CRBN. | 2 | R46,R47 | 100E-00005-0072 | 74LS244 | 8 | Ic 8A-12A,4C,11C,2D — 0986-00803-4808 | |
| 4.7K OHM 1/4W 53 CRN. 20 — RL,R2,R5-R7,R10-R13, — 100E-00005-0079 | TALS245 | 3 | IC 1B,8B,10B | 0986-00803-6400 | |||
| R49, R52-R56,R79, | 7ALS258 | 2 | 1c 136,138 | 0304-00803-0028 | |||
| 81-84 | 74LS273 | 6 | IC 6A,7A,15B,15C,10D, 0986-00803~4700 | ||||
| LOK OHM 1/4W 53 CRBN. = 23, R4 | 100E-00005-0088 | 3H | |||||
| 82K OEM 1/4W 5% CRBN. = =o.1 | RB | 100B-00005-0112 | 7418283 | 2 | IC 76,63 | 0304-00803-0030 | |
| 7ALS298 | 2 | Ic 15E,12K | 0A59-00803-0010 | ||||
| 1K OHM 9 PIN SIP | 4 | RM6-RMO | 102E-00004-0011 | 748367 | l | ici | 0986-00803-7000 |
| 2.7K OHM 10 PIN SIP | 4 | RM1-RM4 | 102E-00004-0020 | 74LS368 | 1 | IC 3E | 0A59-00803~-0012 |
| 4.7K OHM 10 PIN SIP | lL | oRMS | 102E-00004-0026 | 7418374 | 8 | IC 12G,9H,11H,8J,10s, 0986-00803-4600 |
12J,8K,11K
| 1N4148 DIODE | 2 | D1,D2 | 103E-00002-0005 | 74LS377 | 3 | IC 8F,12B,13B | 0A59-00803-0012 |
| 2N4123 NPN XSTR. | 2 | Qo | 104E-00001-0007 | 74LS378 | 2 | IC 7F,9F | 0A59-00803-0013 |
| 2N4403 PNP XSTR. | 1 | @ | 104E-00002-0006 | 74804 | 2 | IC w,4F | 0986-00803-6600 |
| MPSA70 PNP XSTR | 6 | 5-010 | 104B-00602-0012 | COLARB R1 PAL | 1 | Ic 9D | 0F61-00803-0001. |
| TIPLIO NPN XSTR. | 1 | @ | 104E-00009-0001 | ||||
| MYCO1A HAL | 1 | Ic4c | 0986-00803-8900 | ||||
| 20 MHZ COSC. | l | Ici | 0304-00804-0007 | MCO2B HAL | 1 | Ice | 0986-00803-9000 |
| MNCO3B HAL | lcs | 0986-00803-9100 | |||||
| 7406 | 1 | IcK | 0986-00803-7600 | MycO6 HAL | 1 | Ic SH | |
| PACNS REV 1.0 PLA | 1 | IC 23 | A59A-26AAJ-BXHD | ||||
| 74ALS26 | 1 | Ice | 0A59~-00803-0015 |
CROSS REFERENCE LIST:
| DESCRIPTION | QIY | DESIGNATION NO. | PART NO. |
| PAQOUT REV 1.0 PLA | l | IH | A59A-26AAJ-AXED |
| ROMCTRL REV 1.0 PLA | 1 | ici | AS9A-26AAJ-CKED |
| 2018 2kx8 RAM 45NS | 4 | IC 11G,10K,9J,1lu | 0A59~-00803-0028 |
| 2018 2Kx8 RAM 55NS | 1 | Ic loc | 0A59-00803-0029 |
| 6116 2Kx8 RAM 120NS | 1 | Ichs | 0A59-00803-0027 |
| 6116 2Kx8 RAM 150NS | 2 | IC 6B,9B | 0A59-00803-0014 |
| 93419 64x9 RAM | 1 | Ica | 0986-00803-9600 |
| 280B | 1 | icie | 0304-00803-0041 |
| 280B CIC | 1 | Ic2 | 0304-00803-0040 |
| BGO 64K ROM/EPROM | 1 | IC 15a | SEE ROM/EPROM CHART |
| BG] 64K ROM/EPROM | 1 | Ic a | SEE ROM/EPROM CHART |
| FGO 256K ROM/EPROM | 1 | IC8E | SEE ROM/EPROM CHART |
| FG] 256K ROM/EPROM | 1 | IC6E | SEE ROM/EPROM CHART |
| FG2 256K ROM/EPROM | 1 | ICSE | SEE ROM/EPROM CHART |
| FG3 256K ROM/EPROM | 1 | IC4E | SEE ROM/EPROM CHART |
| PROGO 256K ROM/EPRM | 1 | IC 3B | SEE ROM/EPROM CHART |
| PROG] 256K ROW/EPRM | 1 | IC 5B | SEE ROM/EPROM CHART |
| 16 PIN IC SOCKET(.300) | 1 | ICS 3E | 110E-00001-0003 |
| 20 PIN IC SOCKET(.300) | 5 | ICS 5G,5H,2J,3J,13J | 1108-00001-0005 | |
| 24 PIN IC SOCKET(.300) | 8 | ICS 10C,4G,9D,11G,6H, 110E-00001-0009 |
9g,11J,10K
| 24 PIN IC SOCKET(.600) | 3 | ICS 6B,9B,11B | 110E-00001-0007 |
28 PIN IC SOCKET(.600) 10 ICS 4A,15A,3B,5B,14B, 110B-00001-0010 2C, 4B-6E,8E
| 40 PIN IC SOCKET(.600) | 1 | Ics ic | 110E-00001-9011 |
| AUTO INSERT PIN | 1g | a2 | 0304-00804-0009 |
TIN .025 SQ
| AUTO INSERT PIN | 22 | «3 | 0304-00804-0009 |
TIN .025 SQ
| AUTO INSERT PIN | Le | 0304-00804-0009 |
TIN .025 SQ
| AUTO INSERT PIN | 8 | 5S | 0304-00804-0009 |
TIN .025 sQ
| AUIO INSERT PIN | lo | 6 | 0304-00804-0009 |
TIN .025 sQ
| AUTO INSERT PIN | n | owt | 0304-00804-0010 |
TIN .045 SQ
| FERRITE BEAD | 13 | FBI-FBI3 | 0316-00804-9002 |
| ZERO OHM RESISTOR | 6 | SW1-UW6 | 1178-00001-0003 |
(JUMPER)
(CROSS_REFERENCE LIST:
| DESCRIPTION | gry | DESIGNATION NO. | PART NO. |
| SWITCH PC. MIG. | 1 | SW | 0986-00804-3100 |
| 10 POS. DIP SWITCH | 1 | Sw2 | 113E-00001-0004 |
| SNAP | 1 | MHQ3 | 0017-00007-0134 |
PC BOARD A080-91787-F000 MONOBOARD AD84-91787-F000 M051-00114-F156
DESIGNATION LIST:
DESCRIPTION DESIGNATION NO. CPl-cP65 -01 UF AX. CER. P66 100 UF 16V RD. TANT P67-CP142 -O1UF AX. CER. c1,c2 390 PF AX. CER. C3 470 UF 16V AX. ELEC. c4 10 UF 25V AX. TANT. foc} 33 PF AX. CER. C6-C38 1 UF AX. CER. 39 10 UF 25V AX. TANT. ca -01 UF AX. CER C41,C42 390 PF AX. CER. C43-C46 820 PF AX. CER. C47-C52 47 PF AX. CER. 53,054 470 UF 16V AX. ELEC. 55 390 PF AX. CER. 56 47 UF 25V RD. TANT. cs7 68 PF AX. CER. 58,C59 -O1 UF AX. CER. 60 18 PF AX. CER. 61 +01 UF AX. CER. 62 18 PF AX. CER. 63 68 PF AX. CER. 064 68 PF AX. CER. 65 33 PF AX. CER. 066 -Ol UP AX. CER. 67 18 PF AX. CER. 68 18 PF AX. CER. 69 270 PF AX. CER c70 270 PF AX. CER RL,R2 4.7K O8M 1/47) 5% CRBN. R3,R4 10K OHM 1/4W 5% CRBN. R5-B7 4.7K OEM 1/4W 5% CRBN. R8 82K OHM 1/4W 5% CRBN. RO 82 OHM 1/4W 5% CREN. R1O-R13 4.7K OM 1/4W 5% CRBN. R14-R45 220 OHM 1/40 5% CRBN. R46,R47 2.7K OBM 1/4W 5% CRBN. R&B 22 OHM 1/4W 5% CRBN. R49 ,R52-R56 4.7K 1/40 5% CRBN. R50,R51 68 OEM 1/4W 5% CRBN. RST 560 OHM 1/4W 5% CRBN. R58,R59 10 OHM 1/4W 5% CRBN. R60 470 OEM 1/4W 5% CRBN. R61,R62 10 OHM 1/4W 5% CRBN. R63 470 OHM 1/4W 5% CRBN. R64,R65 10 O8M 1/4W 5% CRBN. R66 470 of 1/4W 5% CRBN. R67 2K OHM 1/4W 5% CRBN. ROB 1K OM 1/4W 5% CRBN. R69 510 OFM 1/4W 5% CREN. R70 2K OHM 1/4W 5% CRBN. DESIGNATION LIST: DESCRIPTION DESIGNATION NO. R71 1K OHM 1/401 5% CRBN. R72 510 OHM 1/4W 5% CRBN. R73 1K OHM 1/4W 5% CRBN. R74 2K ORM 1/4W 5% CRaN. RIS 1K OHM 1/4W 5% CRBN. R76 510 OHM 1/4W 5% CRBN. R77, R78 560 OHM 1/4W 5% CRBN. RIS 4.7K OEM 1/4W 5% CRBN. R60 82 OHM 1/4W 5% CRBN. R81-R84 4.7K OHM 1/4W 5% CRBN. REG 1K OEM 1/4W 5% CRBN. R87 82 OHM 1/4W 5% CRBN. R88 47 OHM 1/4W 5% CRBN. R89 47 OHM 1/4W 5% CRBN. R90 47 OFM 1/4W 5% CRBN. ROL 68 OEM 1/4W 5% CRBN. R92 68 OHM 1/4W 5% CRBN. R93 47 OHM 1/4W 5% CRBN. R94 680 OHM 1/4W 5% CRBN. ROS, 680 OHM 1/4W 5% CRBN. RIG 82 OHM 1/4W 5% CRBN. R97 82 OEM 1/4W 5% CRBN. ROB 680 OHM 1/4W 5% CRBN. R99 680 OHM 1/4W 5% CRBN. R100 82 OEM 1/4W 5% CRBN. RLOL 82 OEM 1/4W 5% CRBN.
RMI-BM4 2.7K OHM 10 PIN SIP
RMS 4.7K OxM 10 PIN SIP
RM6-RM9 1K OHM 9 PIN SIP
DL.,D2 1N4148 DIODE Ql 2N4123 XSIR. Q2 2N4403 XSIR. 93 TIP1IO XsTR. for 2N4123 XSTR. G-010 MPSA70 XSTR. Ic 1A 74LS32 Ic 4A 93419 64x9 RAM Ic 5A 74LS157 IC 6A,7A 7418273 IC 8A-12A 7418244 Ic 14a 74Ls00 Ic 15A BGO 64K ROM/EPROM Ic 1B T4LS245 lc 2B NOT USED IC 3B,5B PROGO,PROG] 256K ROM/EPROM IC 6B 6116 2kx8 RAM 150 NS. IC 8B 7ALS245 IC 9B 6116 2Kx8 RAM 150 Ns. Ic 10B 74LS245
MONOBOARD A084-91787-F000 M051-00114-F156
| DESIGNATION LIST: | DESIGNATION LIST: | DESIGNATION LIST: | |||
| DESCRIPTION | DESIGNATION NO. | DESCRIPTION | DESIGNATION NO. | DESCRIPTION | DESIGNATION NO. |
| Ic 11B | 6116 2Kx8 RAM 120 NS. | Ic 1¢ | TALSOB | Ic 12K | 74LS298 |
| Ic 128,138 | 74LS377 | Ic 2G | 7418138 | IC 13K | 74LS174 |
| Ic 14B | BG] 64K ROM/EPROM | IC 3G | 74LS157 | Ic 14K | 74508 |
| Ic 188 | 7418273 | Ic 46 | MMCO1A HAL | Ic 15K | 74LS14 |
| Ic 1c | 280B CPU | Ic 5G | MMCO3B HAL | Ics 4A,15A,3B,5B 28 PIN IC SOCKET (.600) | |
| Ic 2c | 280B CIC | IC 66 | 74F157 | ICS 6B,9B,11B | 24 PIN IC SOCKET (.600) |
| Ic 3c | 74LS157 | Ic 76 | 74LS283 | Ics 14B | 28 PIN IC SOCKET (.600) |
| Ic 4c | 74LS244 | Ic 8G | 74LS173 | Ics 1¢ | 40 PIN IC SOCKET (.600) |
| Ic 5C,6C | 74F157 | IC 96,106 | 7418169 | Ics 2c | 28 PIN IC SOCKET (.600) |
| Ic 7¢ | 74LS157 | Ic 11G | 2018 2Kx8 RAM 45NS | Ics loc | 24 PIN IC SOCKET (.300) |
| Ic 8c | 74P157 | Ic 126 | 7418374 | Ics 9D | 24 PIN IC SOCKET (.300) |
| Ic 10c | 2018 2Kx8 RAM 55NS | Ic 136 | 74LS258 | Ics 3E | 16 PIN IC SOCKET (.300) |
| Ic lic | 74LS244 | Ic U4G | 74LS194 | ICS 45-6E,8E | 28 PIN IC SOCKET (.600) |
| Ic 13¢ | 74LS86 | Ic 1H | 74LS32 | ICS 4G | 24 PIN IC SOCKET (.300) |
| Ic 14c | 74LS153 | IC 2H | 74F174 | Ics 5G | 20 PIN IC SOCKET (.300) |
| Ic 15¢ | 74LS273 | Ic 3H | 74LS273 | Ics 11¢ | 24 PIN IC SOCKET (.300) |
| Ic | 74804 | Ic 4H | T4LS08 | Ics 5H | 20 PIN IC SOCKET (.300) |
| Ic 2D | 74LS244 | IC 5H | PAL | ICS 6H | 24 PIN IC SOCKET (.300) |
| IC 3D-5D | 74LS163 | IC 6H | MMCO2B HAL | ICS 20,35 | 20 PIN IC SOCKET (.300) |
| Ic 6D | 74ALS20 | IC 7H | 74F86 | Ics 9J,llJ | 24 PIN IC SOCKET (.300) |
| Ic 7D | 74LS157 | IC 8H | 74LS86 | Ics 130 | 20 PIN IC SOCKET (.300) |
| Ic 8D | T4F174 | IC 9H | 74.374 | Ics 10K | 24 PIN IC SOCKET (.300) |
| Ic 9D | Colarb Rl Pal | Ic 10H | TAFTA | FB1-FB13 | FERRITE BEAD |
| Ic lop | 7ALS273 | Ic 118 | 74LS374 | SW | SWITCH PC. MIG. |
| Ic 11D | 74LS157 | Ic 12H | 74LS20 | SA | 10 POS. DIP SWITCH |
| Ic 120 | 74Ls174 | Ic 13H | 7418258 | JW1-JW6 | JUMPER |
| Ic 13D | T4LS194 | Ic 148 | TALSL74 | a | AUTO INSERT PINS TIN .045 |
| Ic 15D | 74LS153 | Ic ly | 74LS55 | SQ. PIN | |
| Ic 1E | 20 MHZ COSC. | Ic 25 | PACNS REV 1.0 PLA | J2-J6 | AUTO INSERT PINS TIN .025 |
| IC 2E | T4E74 | Ic 30 | PACOUT REV 1.0 PLA | SQ. PIN | |
| Ic 3E | 74LS368 | Ic 43 | 74LS175 | MHQ3 | SNAP |
| IC 4E-6E,8E | FG3,FG2,FG1,FGO 256K ROM/EPROM | IC 63 | 74LS283 | PC BOARD | A080-91787-F000 |
| IC 9E | 74F10 | Ic 7d | 74Ls02 | ||
| IC 10E | 74LS138 | Ic 80 | 74LS374 | Released 12 Sept. 86 QM | |
| Ic 11E | TALS194 | Ic 90 | 2018 2Kx8 RAM 45NS | Rev. 1 - 20 Nov. 86 moved 5H to chart. QM | |
| IC 12E | 7ALS74 | Ic 103 | 7ALS374 | ||
| IC 13E,14E | T4LS194 | Ic llu | 2018 2Kx8 RAM 45NS | ||
| Ic 15E | 74LS298 | Ic 125 | 74LS374 | ||
| Ic 1F | 74LS367 | IC 135 | ROMONTRL REV 1.0 PLA | ||
| IC 2F,3F | 74.820 | Ic 14d | 74LS161 | ||
| Ic 4F | 74804 | Ic 1K | 74504 | ||
| Ic 5F | 74LS32 | IC 2K | 7406 | ||
| Ic 6F | 74LS00 | Ic 3K | 74LS74 | ||
| IC 7F | 74LS378 | Ic 4K | 741832 | ||
| Ic 8F | 74LS377 | IC 5K,6K | 7ALS74 | ||
| IC 9F | 7418378 | Ic 7K | 74LS169 | ||
| Ic 10F | 74F86 | IC 8K | 74LS374 | ||
| Ic iF | 74F00 | Ic 9K | 74LS169 | ||
| IC 12R-14F | 74LS194 | Ic 10K | 2018 2Kx8 RAM 45NS | ||
| Ic 15F | 74LS74 | Ic 11K | 74LS374 |
3-10 Bp<017>
INPUT aus: [>
SHEETS 2-3
oureur-Bus SHEET 3 L_SORNFLE SHEETS 5-9 FREEZE~ i wo. PuRSS: SHEETS 22-29
HELIN. ‘GVBLNE CHPBLNK
[wcuxe nous HOLE URS WRESET~
Jt = 12 PIN KKIS6 MAIN POKER CONECTOR 23D a Time_Base suet 12 PuRSS HeLK | FOREGROUND
Top LEVEL SHEETS 3-4
nipuT_sus ge = 19 PIN KK1@9 2 1 >—
Pai anb52 Bo ays covyaggisa
09934999 ni
s+ 4 oe nigHEL-e2 MONT ToR_2us {>
SHEET 4
BALLY MIDWAY FG. CO. MONOBORRD PC. 964-91787-F9008 mest-e0114-F129 SHEET 3 OF 25 [Rev 2 We. co. 90e4-91707-Foxe mes 1~09114-F 129
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
BALLY MIDHAY HFG. CO.
ox
3-13
3-14 Bacoer 15) 2ausige
aroro~ F> 7aLsee pRD~ Dai A a8
BuR~ ZI =
zavsee noreSt c. MEDNICK 1 Pee nowoBoRRD PC.
3 Sep 85 BALLY MIDUAY FE. CO. [SHEET 9 OF 25 [REV
Teeur_pus 1Pec@:79, 3P16087>, 1P2C0:7>, 1P4ceH7> zausess 1a ya]
eve jzas eve 2aq eve Ta pausess | 2auseas NOTESE c. RERNICK BALLY MIDUAY HFE. co. PER ONOBeARD PC.
‘o SeP 86
Pe elie
3-16 ‘6ae~
MeeseT~ tek
ReaDY~ . RON_CNTRL Pac-entee WY Lop ————— Suc 16
Let Rp<09: 31
JL rracore> STAGE_RaM RYPCO13) PrX_nUx
HOE sneer 12, o Hex pKDco27)
Dm» Dito Dt 5 [> vire~ ic > vw
THE > vine > vn GATE LINE_sUF Prxour ik
LDOFF=
- > rcore-
eux ° arn [> reou~
SHEET 20
aruie moHOBoARD PC.
ate Rates eT nex PALLY NIBHAY AFG. CO. ‘monOBOARD PC. e4-91787-F 000 mesi—eo1s4—F129
3-17
3-18 lea y 12, RALLY MIDUAY AFG. CO. SHEET 10 oF 25 [Rev
= vce I
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
BALLY NIDMAY HFG. CO.
S68pr BAe? TH
Pe 2 ype 1
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
2N4123 a4
D>
cace:s)
BD(@!7)
NOTES? C. MEDNICK BALLY MIDWAY MFG. CO.
MONOBOARD PC, 9 SEP 86 AG84-91787-F 888 W@S1-e8114-F129 SHEET 25 OF 25 [REV
5 SOUNDS GOOD > A084-91863-B000 1 MO51-00114-B151 Tr
5 ° lo o 38 a DESIGNATION LIST 32 wo as NE 2
Bs = DESIGNATION DESCRIPTION
| a | CP1-CP7 ,CP9-CP13 | -O1MF AX CER. | |||
| 8 | Go | CP14,CP15 | 10MF AX TANT. | ||
| 6 | Zz 8 | cP16 | 1LOOMF AX ELECT. | ||
| 3 | Zao | cP101,cP102 | 0.1UF AX CER. | ||
| 5 | haa | C1,C2 | 390PF AX CER. | ||
| 3 | ole | C3-C5 | 1OOPF AX CER. | ||
| a | o | C6,C7 | 820PF AX CER. | ||
| a | im | ° | >~n@ | c8-C11 | 100PF AX CER. |
| ee _ oe | roe | 3 | asa | C101 C102 | 390PF AX CER. |
| a | a | 3 | zoe | 103 | IMF RO TANT. |
| bee Y | 4 | 3 | YO | c104 | .OIMF AX CER. |
| peawenel | > | nO | 105 | 47MF AX ELECT. | |
| lL | <r tte | 3 | << | C106 | 680PF AX CER. |
| 8 | C107 | .O1MF AX CER. | |||
| : | g | c108 | 1MF RD TANT. | ||
| 3 | c109 | 68PF AX CER 10% | |||
| aw | C110 | 01 MF AX CER. |
cll 150PF AX CER 10%
| : | c112 | 470 PF AX CER 10% |
C113 270 PF AX CER 10% c114 IMF RD TANT.
| x | C115 | 5600PF AX CER 10% | ||
| 2 | Ns | C116 | -O1MF AX CER. | |
| pores | Zz | . | C117 | IMF RD TANT. |
| a} | ful 8 | C118 | 270PF AX CER 10% | |
| =| | I21ao | C119 | 10MF RD TANT. | |
| oily | 120 | .O1MF AX CER. | ||
| :uu | C121 | 1OMF RD TANT. | ||
| le, | esse | c122 | 47MF AX ELECT. | |
| Je [gece | €123 | 1OOMF AX ELECT. | ||
| g]e jie: t | C301 | 150PF AX CER. | ||
| |S |3e de. | 302 C303 | 470PF AX CER 10% | ||
| H | Tus | €304,C307 | 0.1UF AX CER. |
a? bso R1-R3 4.7K OHM 1/4W CRBN. RA 10K OHM 1/4W CRBN. R5 100K OHM 1/4W CRBN. R6-R7,R9 4.7K OHM 1/4W CRBN. R10 1K OHM 1/4W CRBN. R12-R14 4.7K OHM 1/4W CRBN. R15,R16 10K OHM 1/4W CRBN. R17,R18 100 OHM 1/4W CRBN. R19-R21 10K OHM 1/4W CRBN.
SOUNDS GOOD A084-91863-B000 M051-00114-B151 DESIGNATION LIST DESIGNATION LIST
| DESIGNATION | DESCRIPTION | DESIGNATION | DESCRIPTION |
| R22 | 100K OHM 1/4W CRRN. | u14 | 74F 32 |
| R23 | 10K OHM 1/4W CRBN. | U15 | SGO1RO PAL |
| R24 | 100K OHM 1/4W CRRN. | U16 | RAM 2K X 8 |
| R25 | 100 OHM 1/4W CRBN. | U17,U18 | ROM/EPROM |
R26 47K OHM 1/4W CRBN.
| R101 | 12K OHM 1/4W CRBN. | FB1,FB2 | FERRITE BEAD |
| R102 | 160K OHM 1/4W CRN. | FB101,FB102 | FERRITE BEAD |
| R103 | 100 OHM 1/4W CRBN. | FB301 | FERRITE BEAD |
R104 330K OHM 1/4W CRBN.
| R105 | 24K OHM 1/4W CRBN. | ICS U5 | 64 PIN IC SOCKET |
| R106 | 3.3K OHM 1/4W CRBN. | ICS U6 | 24 PIN IC SOCKET .600 |
| R107 | 24K OHM 1/4W CRBN. | ICS U7,U8 | 28 PIN IC SOCKET |
| R108 | 150K OHM 1/4W CRBN. | ICS U9 | 40 PIN IC SOCKET |
| R109 | 82K OHM 1/4W CRBN. | ICS U10 | 16 PIN IC SOCKET |
| R110 | 510K OHM 1/4W CRBN. | ICS U15 | 24 PIN IC SOCKET .300 |
| R111,R112 | 120K OHM 1/4W CRBN. | ICS U16 | 24 PIN IC SOCKET .600 |
| R113 | 33K OHM 1/4W CRBN. | ICS U17,U18 | 28 PIN IC SOCKET |
R114 330K OHM 1/4W CRBN.
| R115 | 150K OHM 1/4W CRRN. | Jl | AUTO INSERT PIN TIN .025 SQ. |
| R116 | 33K OHM 1/4W CRBN. | J2 | AUTO INSERT PIN TIN .045 SO. |
| R117 | 18K OHM 1/4W CRBN. | J3 | AUTO INSERT PIN TIN .025 SQ. |
R118 100K OHM 1/4W CRBN.
| R119 | 510K OHM 1/4W CRBN. | JW1-JW3 | ZERO OHM RESISTOR |
R120 47K OHM 1/4W CRBN.
| R121 | 1K OHM 1/4W CRBN. | LED 1 | GREEN LED |
R122 2.7K OHM 1/4W CRBN.
| R123,R124 | 360 OHM 1/4W CRBN. | sw | SWITCH PC MTG. |
R125 180 OHM 1/4W CRBN.
| R126 | 2.7K OHM 1/4W CRBN. | Y1 | 16 MHZ XSTAL OSC. |
R127 560K OHM 1/4W CRBN. R202 100 OHM 1/4W CRBN. nl NOT INSERTED 03-D4 1N5817
Q1-Q3 2N5305
ul MC 3340 U2, U3 LM359 U5 68000G8 CPU U6 RAM 2K X 8 U7 ,U8 ROM/EPROM ug 6821 P.I.A. U10 AD7533JN DAC ull 14584 /40106 u12 74874 U13 74LS04 GROSS REFERENCE DESCRIPTION
68 PF AX CER 10% 100 PF AX CER 150 PF AX CER 10% 270 PF AX CER 10% 390 PF AX CER 470 PF AX CER 10% 680 PF AX CER 820 PF AX CER 5600 PF AX CER 10% +01 MF AX CER
0.1 UF AX CER 1 MF RD TANT 10 MF AX TANT 10 MF RD TANT 47 MF AX ELECT 100 MF AX ELECT 100 OHM 1/4W CRRN
180 OHM 1/4W CRRN 360 OHM 1/4W CRBN 1K OHM 1/4W CRBN 2.7K OHM 1/4W CRBN 3.3K OHM 1/4W CRBN 4.7K OHM 1/4W CRBN
10K OHM 1/4W CRBN
12K OHM 1/4W CRBN 18K OHM 1/4W CRBN 24K OHM 1/4W CRBN 33K OHM 1/4W CRBN 47K OHM 1/4W CRBN 82K OHM 1/4 CRBN 100K OHM 1/4W CRBN 120K OHM 1/4W CRRN 150K OHM 1/4W CRBN 160K OHM 1/4W CRRN 330K OHM 1/4W CRBN 510K OHM 1/4W CRBN 560K OHM 1/4 CREN
1N5817
2N5305
74LS04 74F 32 gry.
a ANNNN SS MERE WRN TH
CENYNYNE
PME NNERENNNRH
ee wir DESIGNATION
c109 €3-C5,C8-C11 €111,C301 C113,C118 C1,C2,C191,c102 C112,C302,C303 C106 C6 ,C7 cls 104,¢197,c110 C116,C120,CP1-CP7, CP9-CP13 €304,C307 ,CP101 ,CP102 €103,C108,C114,C117 cP14,CP15 C119,C121 C105 ,c122 CP16,C123 R17 ,R18,R25,R103, R202 R125 R123,R124 R10,R121 R122,R126 R106 R1-R3,R6-R7,R9 R12-R14 R4,R15,R16,R19-R21, R23 R101 R117 R105,R107 R113,R116 R26,R120 R109 R5,R22,R24,R118 R111,R112 R108,R115 R102 R104,R114 R110,R119 R127
D3-D4
Q1-03
U13 ul4 PART_NUMBER
0307-00800-N011 0304-00800-0001 0307-00800-0010 0307-00800-0009 0986-00800-3000 0307-00800-0008 0358-00800-0002 0304-00800-0002 0307-00800-0007 0986-00800-2200
0986-00800-0200 0307-00800-0004 0986-00800-0700 9307 -00800-0005 0307-00800-0003 0307-00800-0006 100E -00005-0033
100£-00005-0039 100£ -00005-0048 100E-00005-0061 100E-00005-0071 100E-00005-0074 100E -00005-0079
100£ -00005-0088
100E -00005-0090 100E -00005-0093 100E -00005-0097 100E-00005-0100 100E-00005-0104 100E-00005-0112 100E-00005-0115 100E-00005-0118 100E-00005-0120 100E-00005-0121 100E -00005-0128 100E -00005-0133 100E -00005-0134
103E-00003-0009
0360-00802-0012
0304-00803-0060 0304-00803-0059
CROSS REFERENCE SOUNDS GOOD A084-91863-B000 M051-00114-B151
| DESCRIPTION | Qry. | DESIGNATION | PART NUMBER | : |
| 74S74 | 1 | u12 | 0304-00803-0061 | } |
| 14584 /40106 | 1 | ull | 0304-00803-0056 | i |
| 6821 PIA | 1 | u9 | 0304-00803-0054 | ‘ |
| 6800068 CPU | 1 | US | 0304-00803-0051 | 2 |
| AD7533JN DAC | 1 | u10 | 0304-00803-0055 | |
| SGOLRO PAL | 1 | u1s | 0£ 36-00803-0009 | |
| LM359 | 2 | U2,U3 | 0304 -00803-0053 | |
| M3340 | 1 | Ul | 0358-00803-0002 | |
| RAM 2KX8 | 2 | U6 ,U16 | 0304-00803-0057 | |
| ROM/EPROM | 1 | u7 | ||
| ROM/EPROM | 1 | U8 | SEE ROM/EPROM | |
| ROM/EPROM | 1 | uL7 | CHART | |
| ROM/EPROM | 1 | u18 | ||
| FERRITE BEAD | 5 | FB1,FB2,FR101,FB102, 0316-00804-0002 |
FB301
| 16 PIN IC SOCKET | 1 | ICS U10 | 110E-00001-0003 |
| 24 PIN IC SOCKET .300 | 1 | ICS UL5 | 110E -00001-0009 |
| 24 PIN IC SOCKET .600 | 2 | ICS U6,U16 | 110E -00001 -0007 |
| 28 PIN IC SOCKET | 4 | ICS U7,U8,U17,U18 | 110F-00001-0010 |
| 40 PIN IC SOCKET | 1 | ICS U9 | 110£ -00001-0011 |
| 64 PIN IC SOCKET | 1 | ICS U5 | 110E-00001-0016 |
| AUTO INSERT PIN | 8 | du | 0304-00804-0009 |
TIN .025 SQ
| AUTO INSERT PIN | 1 | J3 | 0304-00804-0009 |
TIN .025 SQ
| AUTO INSERT PIN | 1 | 32 | 0304-00804-0010 |
TIN .045 SQ
| ZERO OHM RES | 3 | JW1-dW3 | 117E-00001-0003 |
| GREEN LED | 1 | LED 1 | 119 -00001-0001 |
| SWITCH PC MTG | 1 | Swi | 0986-00804-3100 |
| 16 MHZ XSTAL OSC | 1 | Yl | 0304-00804-0008 |
| PC BOARD | 1 | A080-91671-G000 | caaragnags |
6-13-86 Released for Production, CMM. -86 Rev. 1.0 CMM - Changed R101 from 24K to 12K. dl. 6-26 8-05-86 Rev. 2.0 CMM - Removed D1. 8-28 -86 Rev. 3.0 CMM - Changed C301 from 330PF to 150PF.
Je = 12 PIN KKIS6 Hee "S4-§g9?
EXTRESET~ sneer i oF 5 [Rev
3-26
SPARE GATES
[a PeeseeeL8, ee a3. aa es.
conrRaL
RONTYPE
‘to 158 PF. 8/20/06 CHH Ba micK BALLY MIDMAY HFG. CO.
TER 50 NE 86 SHEET 2 OF SREY
eyese/sie e7e56/si2 vee! vec
eresecsie ne vec] a1 Gwp| BALLY NIDKAY AFG. CO. Suet 3 OF 5 ]REW
3-27 07539 2 yop veer | 7a.sea ReSETae ET ‘SHDSELE BALLY RIDUAY HFG. CO. ‘souNDS GooD 10 JUNE 66 n284-9169-Be00 eSi-00114-p1s2 faucet «oF § [REV 9 ~ 12 PIN KK100 [P>s3 4 [> s [Ps @ [P>us 11 ey Pn 6 ANALOG_OUT,
BIRR
1d, TT RY-SENSE Pw 7 Key 39 oteyt e 82 as 12 RV_SENSE ]s9 1 RV_RETURN P]y3 10 REY 1.8 6-26-96 R101 CHANGED TO 12K. CHK
NOTES?
c. MEDNICK ALLY MIDUAY AFG. co.
PER
‘SOUNDS GOOD
18 JUNE 66 004-91863-B008 esi-ae114-Bi52 [SHEET 5 oF 5 [REV
DESIGNATION LIST
DESIGNATION NO. DESCRIPTION
1,02 c3,¢4 5,06 c7-c10
cpl P2,CP3
R1,R2
HSA1,2
MH1-MH4 4.7 MF 25V RO TANT 22 MF 6V RD TANT 470 MF 6V AX ELEC +1 MF SOV AX CER
220 MF 25V AX. ELEC -1 MF SOV AX CER
2.7K OHM 1/4 5% CRBN 27 OHM 1/4W 5% CRBN 1 OHM 1/2W 5% CRBN
B37 50
7 PIN 5 PIN
HEATSINK ASSY
1/4" SPACER MCR/2 DUAL POWER AMP. PC. A082-90910-Fo00
PROJECT ENG | C.MEDNICK
Useoon TRON DIM. TOLERANCES UNLESS OTHERWISE SPEC CONCENTAICITY T1.R. . 002 FRACTIONAL +164 DECIMAL + .005 HOLE DIA + .002—.000 ANGLE . 212° DO NOT SCALE DWG. CROSS REFERENCE LIST
DESCRIPTION
-1 MF SOV AX CER 4.7 MF 25V RD TANT 22 MF 6V RD TANT 220 MF 25V AX ELEC 470 MF 5V AX ELEC
1 OHM 1/2W 5% 27 OHM 1/4W 5% 2.7K OHM 1/4W 5%
B37 30
TIN .045 SQ PINS
HEATSINK ASSY
1/4" SPACER
PC BOARD
THIS DWG IS CONFIDENTIAL & PROPERTY OF BALLY/MIDWAY MFG. CO.
ORN msm Csally [MIDWAY wee. co. ik FRANKLIN PARK, IL 60131 MECH CHK MATC DUAL PWR AMP
ELEC CHK ary DESIGNATION NO.
6 C7-C10,CP2,CP3 2 c1,c2 2 3,4 1 cP 2 €5,C6
4 R5-RB 2 R3,R4 2 R1,R2
2 U1,U2
12 J1, 52
2 HSA1,2
4 MH1-MHA PART NUMBER
0986-00809-1100 0986-00800-3100 0986-00800-1600 0986-00800-3200 0986-00809-1700
0062-026D3-1XXx 0062-068B3-1XXx 0062-199B3~-1XxXx
(1066-1 88XX-XX4Xx
0017-00033-0430
A986-000110-E000
0017 -00042-0320
A080-909 10-F 000
REVISIONS
ASSEMBLY DRWNG A084-90910-FO0O PART NO.
MO5 1 -00986—FOIO
Vv AUDIO
N.C. L. AUDIO L. SHIELD KEY VAUDIO RETURN
R. AUDIO R. SHIELD V AUDIO L. SHIELD ONOnanuan —
R SHIELD
vauDi0o —>—— ? —B TO CHIPS + CPI cp2 cP3 220 UF 25V AUF AUF Vv auDlio RETURN THIS DWG. IS CONFIDENTIAL & PROPERTY OF BALLY/MIDWAY MFG. CO PROJECT ENG: C.MEDNICK
4. DIM. TOLERANCES S 2: UNLESS OTHERWISE SPEC —_ ET (silly |minwa Y MFG. co. CONCENTRICITY TR. . 002 | FRANKLIN PARK, IL 60131 FRACTIONAL = .1164 77 | 6/14/84 DECIMAL + .005 _ DUAL POWER AMP HOLE DIA +.002—.000 SCHEMATIC ANGLE +12" REVISIONS PART NO. A080— 90910— FO0O MO5!1-00986-FOII DO NOT SCALE DWG.
BRUNING: 40-107
+izv Bia
+5v @ 12a
@ ROT 5 “~ (| com D) | @ ; 8 C)
ze aan
@| cer -tt — —_— OPTOCOUPLER. 10/50 | " ~ or a Jz +4251 47/55 san
cw a 1/50 ‘am Lok t%e cn = ee a ve S00 00, CER MET aos TLAaNCLP . ear wore Oy 10m 1%
Taman, CRF SB annette
3-30 7 rneree vauee croraeant /VOuTS . FOR ADDITIONAL ELECTRICAL INFORMATION, SP\OIG
- TESTOR VALUES APE IN ORS Yaw, 5%, C8 REFER TO MECH. DWG. NO. 0017-00003-0543. =a eres a NOTES! UNLESS OTMeRWise SPECIIEDL Dd} | 3\- SPIOIG Ix | po nO7 SCALE onaawnes eee a
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
FCC FILTER 8D. FOR MONO BD le. STRAP io a mTee Mtge?
+--+ FET
Bl
- BALLY MIDWAY “4 A080-91870-A000 Keyl op (Pais)
ee nz eas Eade one cused Foe Modvets ors REVISIONS PROJECT ENG: C.MEDNICK usep on RAMPAGE
om URE fat ASSEMBLY DRAWING ECC. FILTER FOR MONO BD. | MOSI-OOE36-AI6O ( A084-91870-A000 ) @aly | MIDWAY MFG.CO. FRANKLIN PK. ILL.
DIM. TOLERANCES UNLESS SPECIFIED
CONCENTRICITY FUR 005) FRACTIONAL 64 DECIMAL. * 005 HOLE DIA
3-32 FCC FILTER BOARD FOR MONOBOARD PART NO. A084-91870-A000
DESIGNATION LIST
DESIGNATION NUMBER
Cl - C3 FB1 - FB4 vi J2 JW1 = JW2 KEY 1
CROSS REFERENCE LIST
DESCRIPTION Ooty.
-01 UF AX. CER 3 FERRITE BEAD 4 HEADER 12 PIN KK156 R/A 1 OMIT PIN 5 CONNECTOR 12 PIN KK156 R/A JUMPER WIRE KK156 KEY P.C. BOARD rene M051-00E 36-A161
DESCRIPTION
+01 UF AX. CER. FERRITE READ CONNECTOR 12 PIN KK156 R/A HEADER 12 PIN KK156 R/A OMIT PIN 5 JUMPER WIRE -KK156 KEY FOR PIN 5 OF J1
DESIGNATION NO.
cl - c3 FR1 - FB4 J2
Jl JW1 - JW2 KEY 1
8/13/86 - Released for Production - CMM 8/14/86 - Rev. 1 - corrected J1, J2 designation reversed. PART NOS.
0360-00800-0005 0316-00804-0002 OE 36-00804-0002
0E36-00804-0001 117£-00001-0003 0017-00021-1353 A080-91870-A000
Je - 1 [ >—————_
se - 2 [ )—————_—_+
FB4 FBe 4 1
| ye-3[D | ’ | RAWS | ' | 1 | 2 | . | [+e |
Je - 4 [ )——4
Je - 5 KEY
sue Jye-6 [| 45 o&=@—_+
1] @. @1uF 1] @. @1UF
| Je-7 D4 | 2] 3 | a] c2 |
Je - 9 [| >———_-++
ve - 1e[ >——-
ge - 11[ >——————_+4 -———_1)>
FBS FBI
| Je - 12 | Eenual | + | 7} E | + | 1 {] z | > Ji - 12 |
CABLE SIDE MONOBOARD SIDE
MTGH2 NTGHI
Relenize NOTES: Sic He FLEA
BALLY MIDWAY MFG. CO. L. DEKKER
FCC FILTER BOARD M@51-@0E36-A162 A@84-9187D-Aveo SHEET 1 OF 1 [REV A
TO MONITOR i> CONTROL CONN. A
POWER CHASSIS A945-88059-8200 SOUND BOARD ‘DOUN L2}
TO COIN DOOR CONN. STROBE, pase __fiev-nry grounn TOTEST BRACKET F12V_RTNI Fiev! +12V! +12V1 GROUND! i GROUND! oiae NET GROUND! SIE GROUND SROUNDT f GROUND | 100 avEL GROUND) She TO MUX BOARD TO COIN DOOR CONN. TER
@BLU-ORN
GRN-BLU
GRN-YEL GRN-HHT
GRN-BLK
GRN-BRN GRN-ORN GRN-GRY
YEL-RED
RED-GRN
RED-ORN
BLK-YEL
WHT-BRN
WHT-YEL m
= z z » 3.
cal GROUND! 11 GROUND! 12 GROUND! 13] GROUND! 14,
@BLU-ER' ‘SBRN-WHTA|
FILTER BALLAST CONAA AD +5vi15 H ayEL GROUND] |
TO _LAMP BOARD
POWER SWITCH AUDIO AMP BOARD TO SOUND BOARD
LINE VOLTAGE SELECTION CHART VOLTAGE ) 105 ; 115 ) 218 ) 220 | 238 248 | COLOR Jumper 1] 5-8 | 5-11] 6-14/11-14]11-14/11-14/@0RN JUMPER 2(14-15/14-15] out | ouT out [aver gunper 3! 4-7 ' 4-10! 4-7 T 4-7 4-131 aRED TO MONO BOARD JS
MONITOR t]Rep 2\GREEN 31 BLUE }4}eROUND SI¥SYNC 6 |HSYNC
7} eRounn 2ivsyNc~ a }HSYNC~ o a a
[yi TeRounn {GROUND iesy ie1ev {KEY {RESET_OUT 'RESET_OUT \+iev {+5v 181 GROUND
- GROUND
{GROUND {GROUND y45¥ {+5y IKEY JRESET_OUT }GROUND i+12Vv 1+5v 1e1+5V 111GROUND |12GROUND
HT-BLU. RIGHT R3_WHT-GRN DOWN RO.
TO POWER CHASSIS GROUND KEYI19) GROUND! 22 GROUND [2:
TO_MONITOR Reni GROUND} 2 GREEN { 3 GROUND {4 BLUES GROUND { 6 KEY 17 HBLNK~! 8 VBLNK~19|
MONO BOARD Ag84-91787-CAeo BRN-BLK BRN-YEL TO COIN DOOR CONN.
COIN 273 START 1 tBRN-RED START 273 RED-WHT
GROUND! 1P181 19} reat tit Ipietie IP13\13 1 BLU-RED BLU-YEL BLU-GRN BLU-WHT Status [70 SOUND BoaRD
1 ORN-HHT. SERVICE, TO TEST BRACKET i GRY-RED rest H UP_R1 DOWN RI. LEFT Ri, RIGHT R1, KEY! 14! 1P141 15 fjp Pee BL 1P15!16| 1p16117| 1P17118 GROUND] 19 GROUND OPst opse wt ——ell BLU-BRN DOWN Li. 1 BLU-ORN LEFT Lij BLU-GRY__ RIGHT Lt TO CONTROL CONN. A
DOWN LS WHT-BRN LEFT U3 HHT-ORI PLR 2/3 _BRN-GRN, RIGHT L3 MHT-GRY, LIGHT 2 ORN-BL f ciGHT 3 ORN
[> 10 CONTROL COHN.
TO @ TO 4 MUXER LIGHT CONTROL PC NOTES?
JAN 16 1987 NOTES:
- = 18ANG 3004 @ = 18ANG 6eay BALLY MIDHAY MFG. R. A. PLOUSSARD F STAR GUARDS CABINET HIRING No51-88E89-AGe3 co.
[SHEET 1 oF 2 [REV
TO_POWER SUPPLY LAMP BOARD jage4~91877-AE GS 1 ]+5¥ @ 1GROUND 9 |GROUND YO CONTROL CONN. 4 {key CONTROLS a fe {onrRoLs LIGHT 2 GRY-RED Ih, tore CONTROL © ORN=BLU UT | controLe LIGHT 1 GRY-GRN TIS tons TO MONO BOARD J4 CONTROL 1 ORN-GRN 19}CONTROL1
To_CONTROL ¢ COIN DOOR =1ev LIGHTS
TO _POWER SUPPLY COIN DOOR Goya y © iL
| GROUND 4h | GRY-BLK | — | |
| TO MONO BOARD J3 | METER | H | WHT-YEL |
cI ——41t— RR it th WaT
| COIN 1 | dak | BRN-WHT | con 1 |
tt COIN 2
| GOIN | deh | PINK | ON | |
| TQ_8 TO 4 HUXER | comn 3 | tek | RN | CON S |
it TILT
| Tut | H | gRY | N |
| aroun | 4°} va | ° |
TO_CONTROL B ZF
TO POWER SUPPLY
SOUNDS GOOD BOARD A@84-91863-BA08 J3' 1 1a GROUND ¥OL POT HIPERT? 2 1A GROUND AUDIO OUTI2 3 145¥ AUDIO OUTI3 4 1s5v ® GROUND!4 5 i+iey @ GROUNDS 6 t+1ay AUDIO OUTIE ? |E GROUND AUDIO OUTI7 Cm @ GROUND!8 a KeEYI9 VOL POT Ata f GROUND! 13 YOL POT Bile!
RED-HHT.
RED-GRN
STATUS YEL-BRN
J) BLK-WHT
ORN-BLK
TO MONO BOARD TO MONO BOARD CONTROL A START 1
| trent 1 CONTROL © gevigey | LIGHT 1 | START 1 | Tp BRIE | bs |
ue Rt
| GRY-RED | eh | BLU-RED | N | ||
| cry | DOWN Ri | gh BuURYEL | DORR A | ||
| TO_COIN DOOR CONN. | ; | ORES | Lert Ri | 44 en | LEFT Rt |
| RIGHT RI | 5 BLUSHHT | NIBH ft | |||
| uP Lt | 4c jp Beu=BLx | et | |||
| TD_CONTROL CONNECTOR | —— | oun us | YP osaes | pak | |
| nge4-91881-Aoee | 47 | ° | |||
| 1 1+5y | i | LEFT ut | |||
| TO_COIN DOOR | al stant | ORN-RED Be lina | LEFT Li | ae Ps BLU-ORN | ° |
| ee | RIGHT L1 | 4 i BLU-GRY | bss Ma |
oe ©
| inea | TO Test BRACKETT Ce ouyn | =_— | |
| START 3 | ORN-YEL | H | 10% |
| RH | GROUNL | tt |
1 | up Re
| UP _R2 | spp SNE | ae |
TO POWER SUPPLY GROUND
PLR 273 START 273 TO MONO BOARD COIN 273
TO_NONO BOARD
TO POWER SUPPLY H DOWN Re H 4 taf GRN-BLU LEFT Re DOWN Re aah SN=EL LEFT «| —o RIGHT RE i RIGHT R2 GRN-HHT iis ; xe | rot
uP Le dis GRN-BLK
DOWN RS DOWN L2 cor FeRN-BRN pout Le
| RIGHT L2 | 43 ‘ GRN-GRY | RrGHe te |
'
| LEFT Le | fe 1 _GRN-ORN | tects | |
' up UP_R3 WHT-RED —45 o DOWN R3 rN ‘ 6 petty t
it 4 + DUAL POWER ANP
| Jt nee4-sa910-Feeo | RIGHT R3 | 1g | _HHT-GRN | RIGRY'RS | |
| lavive | SPEAKER | #2 | © | ||
| qJ2iu avnro | eet | LEFT _R3 | j> §wHT-veL. | Berg Re | | |
| 3iL SHIELD | s6hN | 47} | ° | ||
| faiKey | isft | up 13 | ts j,_HHT-BLK | es | |
| siv AUDIO RETURN L+!49M | geen | t | pou ts | | ||
| J61R AUDIO | NeISp | DOWN L3 | i WHT-BRN | aS | |
| dha | i | Td | 410k | ° | + |
| f7iz sHteLD | L-{6l | 4 | nek | pier La | |
| la!v AUDIO | Spear | RIGHT L3___g, 94 WHT-GRY | |||
| LEFT L3 | bak WHT-ORN | LER ts | |||
| To TEST BRACKET | pogo 4 Heke | it | START 2 | ||
| TEST Bancxer | eTART 2 | 41h ORH=RED | AN | ||
| TO HOMO BORED TE | crv-rep | TERT | | 10 CONTROL A | START 3 | bah ORN-YEL | sragy 3 |
| Se coro. conn, aff ¥EL | \ | GROUND | ce | t |
i ORN-HHT |seRyrce =
| CoP Te novo sonen ye | Fveu-ren re | TO" GOAN DBOR |
| BLK-WHT | | porest | BALLY MIDHAY MFG. CO. |
! wu R.A. PLOUSSARD
| YEL-BRH_! | z | JAN 16 1907 | STAR GUARDS |
| 1°23 | NOTES! | CABINET WIRING |
H $
| TO SOUND BOARD | 1 | ® = 18 ANG 300 | N@51-8BE89-AGOs |
| u | SHEET @ OF ® [REV | | |
agay + 40 1 133HS. 281¥-b1T@0-TSOW @oav-TSsBT6-paoy AaXSIdI LINN & OL 8 9861 61 Jaa
davssnoid “8 “a ‘OD “54M AUMGIW ATTYa
'S3LON @2 NId YaMod @t NId aNnows i bua eve ave Tee St Tet TeeoHee
looo'-z00" + Is yo/t's wr, (COOOV-I88I6-vBOV ) “Ga “xnW tv OL 8 ONIMVEG ATSW3SSV O39 '9SW AVMGIWN | 4727 = No aasn GUVSSNO 1d Y__.ONa Loaroua SNOISIA3Y. Wap] BSP BY man [ ¥ | 2/7] A
“DMG a1V9S LON OG oslv¥=pllOO-IGOW “ON Lavd
Q31siD3a45 $877NN S3INVY3IOL ‘WIG “TA Md NITINV aS
dvVu 986T 930 81 daSva13y BBBV-18816-LBLV aquvog od G2@° SNId LUYSSNI_OLnv te TyZOHy. In SAY WHO AZOI 8Iu-o14 S3¥Y WHO 2ST 6u-T¥ Ya XV 4d9BT 6-19 439 XV dnTo* 2d2 ANVL XV JNOT Idd 000V-18816-080¥ a XW OLS & vee ceeeeeeen a C+ | 1817 NOTLWNDIS3q cares a ory Tmo- CH) Cat Tmt Céad (at GoD CH tao in 20 Cao Cao t+ Cho tat Gt cho Ce beoe-1eee— oer re 1 s2m* Nid LuaSnT OLAy tt CD tao 1BB8-£8820-6839 mM TYZOHPL om cm ~Cai+ SI1#-Sagee-3IH1 BIU-B1e Sau x5 MV/T WHO ABDI
ANVL X¥ 4ngT wao XV dnTg° waz Xv ddogt BBLG-BUBVH-I986H Ido BBBZ-BUBBP-I986H 2do IV BB-BBBIG-A9EH 69-19
I Ss I ga 8898-SHBIS-3VH1 6u-Te 6 SAU XS M¥/T WHO XBT
T 986] W/AT AWMCIW/A TE ©
YaGWAN Luvd NOILVNSIS30 ALO NOTLdI¥9S30
LSI17 39N3¥34d3uN SSOUD IB1V-VITBS-1SOW BHOBV-188l6-vBeV Quvogd YAXSIdILINN » OL B
3-36
BALLY/MIDWAY'S STAR GUARDS (3 PLYR) U.R. #0E89 ROM/EPROM PART NUMBERS
UNPROGRAMMED MONOBOARD A084-91787-F000 PROGRAMMED MONOBOARD A084-91787~-AE68
0E89-00803-0013 0E89-00803-0012 -00803-001T E89-00803-0010 £89-00803-0008 0E89-00803-0009 0986-00803-9200
UNPROGRAMMED SOUNDS GOOD BOARD A084-91863-B000 PROGRAMMED SOUNDS GOOD BOARD A084-91863-AE68
Pos. U17 MIDWAY PART NUMBER JUMPERS 0£89-00803-0002
0E89-00803-0004 0E89-00803-0005 U8
M051-00E89-A008 REVISIONS
01-20-87 RELEASE FOR PRODUCTION