CATHODE RAY TOMES

Arch Rivals Kit Installation (16-4001-K-101 May 1989)

Arch Rivals (rev 4.0 6/29/89) (Bally Midway, 1989) · Installation · 49 pages · 26 sections · original scan

Page 1

16-4001-K-101 May 1989 . Sstlly mip WAY

kit installation

ancl operation

manual

Page 2

HOMETOWN HEROES OPTION - HOW TO CUSTOMIZE YOUR GAME

PUT GAME IN TEST MODE: a. Pull out diagnostic switch inside coin door. b. Activate TILT switch.

SELECT “HOMETOWN HEROES” OPTION: a. Use left player control button. b. Move cursor (ball) to “HOMETOWN HEROES”. c. Press 1 or 2 PLAYER button.

Turn on switch 6 on game board.

Select item to update: a. Use left player contro! button. b. Move cursor (ball) to item to update. c. Press 1/2 PLAYER or ANY left player buttons.

Team Updates (SELECT “NEW COLORS/NEW NAMES”): a. 1 player button for “NEW COLORS”. b. 2 player button for “NEW NAME”.

NEW COLORS: a. Move left player joystick to change colors. b. Press any left player button to save. c. TILT to abort.

NEW TEAM NAME: a. Move left player joystick to change LETTER. b. Press any left player button to save LETTER. c. Use (<--------) to ERASE. d. Clear out all unwanted letters. e. Move to “DONE” and press button to save. f. TILT to abort.

TO CHANGE “PRESENTS” SCREEN: a. ENTER NAME AS YOU WOULD LIKE IT TO APPEAR

  • CENTER NAME OVER “PRESENTS” USE SPACE or (<------>). b. Move left player joystick to change LETTER. c. Press any left player button to save LETTER. d. Use (<------- ) to ERASE. e. Clear out all unwanted letters. f. Move to “DONE” and press button to save. g. TILT to abort.
Page 3

TABLE OF CONTENTS

Notices and Warnings. ... 2.2.0... 000 c eee eee ee eee eee 1

Installation Cabinet Modifications... eee ee eee teens Control Panel Modifications. Installing the Interboard Wiring... 2.2.22. eee eee eee eee eee 4 Installing the FCC Cage... . ee ee cee eee eee eee eee 5

Game Play... 6... eee eee teen eee eee eens 6

Dignostics and Adjustments. ...... 0.000 eee eee eee 7 Dip Switch Settings... 2... 22. ee eee eee eee ee eee eee 9

Troubleshooting General Operation... ......0000eee eee eee eens Simplified Block Diagram... . Detailed Block Diagram Troubleshooting Chart. Jamma/Joystick Cable Chart... 0. cee ee ee ee eee

Decal Locations. ... 2... 0... cee cee eee eee 18

Joystick Wood Spacer Diagram. ... 1... 0... cece eee eee eee 19

Volume Control Wiring .........-. 2. - eee eee eee ee eee 20

Diagnostic (Test) Switch Wiring... ......... 0.00. e eee eee 21

Circuit Board Schematics and Parts Lists 68000 Video Game Board... 1... eee ee cee eee eee eee 22 Music Board......... Jamma Interface Board.

Interboard Wiring Diagram.

Kit Parts List... 0... eee eee eee 41

ROM Summary. .... 0... 0c eee eee eee eee 42

Page 4

Notes...

Page 5

Notices and Warnings

Notice Parts salvaged from an old game are required to complete your kit. These salvaged parts must operate perfectly or the converted game cannot perform properly or safely. Always repair circuit board malfunctions and cabinet damage before conversion is attempted.

These parts are:

  • A Power Supply capable of +5V DC at a minimum of 7A; -5V DC at a minimum of 1A and +12V DC at a minimum of 1A. These operating voltages are necessary for your kit. Your Power Supply must be FCC approved.
  • A Monitor with a horizontally mounted CRT that is capable of 16KHZ and Raster electronics with inputs for red, green, and blue video, as well as composite sync.
Warning Use of Non-Bally Midway Parts or Circuit Modifications May Cause Serious Injury or Equipment Damage. Use Only Bally Midway Authorized Parts.
  • For satety and reliability, substitute parts or modifications are not recommended.
  • Substitute parts or modifications may void FCC type acceptance.
  • This game is protected by federal copyright, trademark and patent laws. Unauthorized software or hardware modifications may be illegal under Federal law. This law also applies to Bally Midway logos, designs, publications, and assemblies. Moreover, facsimiles of Bally Midway equipment (or any other feature thereof) may be illegal under Federal law, regardless of whether or not such facsimiles are manufactured with Bally Midway components.
Warning Prevent Shock Hazard and assure proper operation. Only plug this game into a properly grounded outlet. Do not use a cheater plug to defeat the powers cord’s ground pin. Do not cut off the ground pin.
important Check the Arch Rivals kit for an FCC sticker and apply it over the existing sticker on the cabinet. When Bally Midway ships a game, it is in compliance with FCC regulations. Your sticker, is proof. If your sticker is missing or damaged, legal repercussions to the owner or distributor of the game may result. If your game doesn’t contain a FCC sticker contact your Bally Midway distributor immediately.
Page 6
Warning This equipment generates, uses and can emit radio frequency and, if not installed properly and used according to the directions in this manual, may cause interference to radio communications. It has been tested and found to comply with the limits fora Class A computing device pursuant to Subpart J of Part 15 of FCC rules which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference to radio communications, in which case the user, at his or her own expense, will be required to take whatever measures may be needed to correct the interference.

Disconnect power during set-up and repairs. To avoid electrical shock, disconnect the game from the AC power source before removing or repairing any part of this game.

Page 7

Installation

Cabinet Modifications

  • First, inspect your old cabinet. Remove foreign objects and fill in gouges with a good quick-hardening wood putty. Sand cabinet and wipe it clean.
  • Repaint the cabinet with black semi-gloss paint, (for games with wood grain sides: remove the old decals and clean the glue residue from the old decal). Allow to dry and set.
  • Pencil a line roughly at the top of the old graphic. Lightly moisten the cabinet with soapy water or glass cleaner. Apply the decal starting at the top and working down. After the decal is in place, use a piece of the foam packaging as a squeegee and smooth the decal down, taking care to squeeze out the air bubbles. If you miss an air bubble, pop it with a razor blade or a pin and burnish it down. Ailow 12 hours for the adhesive to set. Remove masking.
  • Position the FCC sticker near the power cord.
  • Apply the CRT overlay to the glass covering the CRT.
  • Apply the instruction decal.

Control Panel Modifications

  • Remove the control panel buttons, joysticks, and the old viny! covering .
  • Place the panel template on the control panel, and use it to help you align your control panel.
  • Leave your 1 and 2-Player buttons where they are. Drill holes as needed for the joysticks and other buttons. Plug any old holes with wood blocks, putty, cardboard, or epoxy. File the new holes smooth.
  • Carefully remove the backing on the vinyl control panel overlay. Place the overlay on top of the control panel. Assure that no air bubbles get under the vinyl overlay.
  • After the overlay has been securely applied, use a razor knife to cut holes for the buttons and joysticks. Player-1 and Player-2 START stickers go next to the appropriate buttons. A joystick direction decal goes around the joystick opening. Position Pass/Punch/Stea!l, and Shoot/Block stickers according to the template.
  • To mount the joystick assembly to the conirol panel, first push the joystick shaft and handie through the control panel from the back. If you have a metal control panel, or if the joystick protrudes too far out of the hole, insert the wood spacer included with your kit between the joystick mounting bracket and the control panel.
Page 8

Once you have positioned the joystick, attach it to the back of the control panel with the Phillips screws provided. Repeat the procedure for the remaining joystick.

  • To mount push buttons to the control panel, insert the buttons through the control panel from the top and secure into place with mounting nuts provided with your kit.
  • Next, attach the blade switches to the control panel. Start by positioning the switch so that the long blade just covers the round tab on the bottom of the push button. The short blade should be facing you, not the control panel. Secure into place with Phillips screws.
  • After all control panel components are installed, attach the protective cover. It may be necessary to cut holes to accommodate the control pane! components.

Installing the Interboard Wiring

  • Disconnect the old wiring harness from the CPU board. Use the schematic drawing from your old game to carefully note the function of each wire. Label the wires, if it will help to do so.
  • Carefully remove the circuit boards and the metal circuit board panel. Leave the transformer chassis in the game.
  • Leaving several inches of wire at each connector, cut the wires near the coin door, monitor, player panel, power supply, and speaker. Do not cut the other side of these wires. That is, the side that is connected to the CPU should not be cut.
  • Following the Wiring Diagram Schematic or the Jamma/Joystick Cable chart, solder the coin door, monitor, player panel, power supply, and speaker wires to the Jamma/Joystick Cable. Using electrical tape, be sure to insulate all splices.
  • The cables for the joysticks plug into the PC boards that are part of the joystick assembly. The cable for the left joystick has orange wires. The cable for the right joystick has yellow wires.
  • If your game has a series-pass transistor for the power supply on a separate heatsink, remount the metal heatsink beside the power supply board.
  • Check and clean the input jack on the power supply board. Replace any burned or damaged pins.
  • Install diagnostic (test) and tilt switches according to the Wiring Diagram Schematic. You may find it convenient to install the tilt switch in the coin door and the diagnostic switch on top of the cash box.
Page 9

Installing the FCC Cage

  • Use the screws supplied to mount the FCC cage inside the game either on the back door or on one of the walls. Do not open the FCC cage while installing it.
  • Remove one mounting screw trom each of the following: the transformer, the power-supply board, the cage, and the mounting plate for the FCC cage. Attach the ground braid between each one of these and replace the screws. The cage and the mounting plate for the FCC cage must be grounded separately.
  • Plug the Main Harness into J1-of the Jamma Interface Board. Support the cable as necessary with plastic wire guides. Jack J5 on the Jamma Interface Board is the connection for Player-1 Joystick and has a cable with mostly orange wires plugged into it. The other end is plugged into the Player-1 Joystick PC Board. Jack J4 on the Jamma Interface Board is the connection for the Player-2 Joystick and has acable with mostly yellow wires plugged into it. The other end is plugged into the Player-2 Joystick PC Board.
Page 10

Game _ Play

Starting Up Turn the game on. After the player inserts the required number of coins, the game exits the attract mode and enters the play mode. Play mode halts until the oneplayer or two-player CREDIT button has been hit. After the player selects the ARCH RIVAL character for the game, game play will commence.

Player Controls Credit Buttons designate one-player or two-player modes.

Joystick allows the player to assume 49 positions and move in 4 directions.

White Buttons allow the player to Pass in offense and Punch or Steal in defense.

Red Buttons allow the player to Shoot in offense and Block in defense.

Scoring The game basically follows the same rules as basketball. Two points are awarded for each completed basket shot. Three points are awarded for completed shot outside the three-point line. The game does not account for fouls, so players are encouraged to use the Punch feature to make the game more enjoyable.

Ready-To-Play Mode The Ready-To-Play mode begins when proper coinage has been accepted in the coin slot. During this mode the game will ask the player(s) to press the one-player or two-player Credit button. After the Credit button has been pressed, player will get a chance to pick a character to represent them in a game. After selecting a character press the Shoot or Pass button to proceed into game play. If a character is not selected the game will assign one automatically.

Play Mode The Play Mode begins for each player when the Shoot or Pass buttons have been pressed. The Play Mode ends for each player when game time runs out. “Video Time Out-Insert Coin” appears on the screen, signaling the player to insert another coin to continue game play. The player has 15 seconds to insert another coin to continue the game that was already started. After 15 seconds, the Play Mode will start with a new game.

Offensive Play To Shoot or Pass, press the appropriate button. To “fake out” an opponent, hold the button down longer. If your teammate is holding the ball, you can “tell him” to Shoot or Pass by pressing the appropriate button.

Page 11

Defensive Play To Block, press and release the shoot button. To Steal, aim your player at the ball, and press either Pass button.

Diagnostics and Adjustmen

Diagnostic Mode By pulling the white diagnostic switch and pressing the tilt switch, the operator can enter the Diagnostic Mode. The Diagnostic Mode can be entered at any time from any mode of operation. Once in Diagnostics, the operator has access to several features and self-test operations. . These are shown on the screen. Use Player Joystick the move cursor. Press 1 or 2 Player Button to start the test.

Self-Test This test is designed to locate and identify any computer malfunctions. When selected, the game enters this mode immediately and begins scanning its memory. The phrases “PASSED TEST” or “FAILED TEST” will appear on the screen depending on whether the test was successful or not.

“Hometown Heroes” The operator has the capability to program names and colors of his choice for four different teams which his game will feature. Having entered into “Hometown Heroes”, select the team that is to have their name and/or colors updated using the left joystick. Press the Credit Button to proceed. The game requests the operator's choice between NEW COLORS and NEW NAME, (Press the two-player Credit Button for NEW NAME, or the one-player Credit Button for NEW COLORS). Both of these items may be changed, but only one at a time. Again, press the Credit Button to proceed. When programing the new information, use the joystick to select your choice, and press the Shoot Button to enter that choice.

Reset High Scores The game automatically clears High Scores when either Credit Button is pressed.

Switches The Switch and Sound Self-Test mode allow the operator to determine if all game switches, sound features, and the opto-board controlled joysticks are operating properly. The operator can activate switches one at a time and check the monitor screen to see if they are acknowledged.

Page 12

Sounds The two Credit Buttons activate the Sound-Test during the Switch-Test mode. Press the one-player Credit Button to run through the music features and the two-player Credit Button to test the speech functions.

Joysticks To assure that the joysticks are operating properly, while in the Switch Test mode, check to see that they can be moved for three units in all of the appropriate (up, down, left, right) directions.

Grid : The Convergence Grid Display Test displays a crosshatch pattern to aid in adjusting the color monitor. This pattern is useful in adjusting the color balance, convergence, vertical linearity, and vertical/horizontal sizing. To exit this test, press the Tilt switch.

DIP Switch All game options are adjustable by changing the bit switch settings on the DIP Switch unit (on the 68000 Video Board in location 12A). The DIP Switch unit combines ten bit switches, which are set to the On or Off position. When you enter this test mode, the screen shows a full display of current DIP Switch settings.

Page 13

Arch Rivals OPTION (DIP) SWITCH SETTINGS TABLE

GAME TIME: Preset Preset + 10 sec Preset + 20 sec Preset + 30 sec

COIN CHUTE: 1 Coin;1 Credit 2 Coins;1 Credit 3 Coins; Credit |. 2 Coin: it Fe

1 Coin; 6 Credits}.

“HOMETOWN HEROES": Progammed Default Teams

ATTRACT

SEQUENCE

SOUNDS: Sounds E No Sounds,

Free Game No Free Game

FREEZE SW: Freeze Mode Normal Operation

  • Switch 9 : Not Used
Page 14

Tr leshootin

General Operation The following section gives a brief overview of the ARCH RIVALS computer system. A troubleshooting chart is located at the end of this section. The chart may help the operator locate a faulty component quickly.

68000 Microprocessor The computer in your Arch Rivals game is controlled by a Motorola 68000 microprocessor. Microprocessor chip 4E is on the CPU Board. This chip has 32 address lines and 16 bidirectional data lines. As with other microprocessors, each of these lines corresponds to an address or data bit.

Local Memory Devices Local ROM. The Game program is in Local ROM chips 2B, 2C, 3B, and 3C. Also stored in this ROM is staging data used in the game’s Foreground Packet Section.

Local RAM. The microprocessor uses Local RAMs 4B and 4C, when it processes program or peripheral data. RAM chip 4B contains the eight “low” bits, while chip 4C holds eight “high data bits”.

Image Storage Your game stores image data in three places. Two of these control foreground graphics; a third furnishes background image.

Foreground Packet Section. The first section is a library of details about foreground (moving character) images. Because these details are packetized, this section is called Foreground Packet Section. The system computes such details or retrieves them from Local (program) ROM. These details may involve a character's position in the screen. They may also specify the group of colors for its display. However, digitized image description (called bit maps) are stored and manipulated elsewhere.

i jon. The second section is the Foreground Bit Map Section. This includes a Foreground Image ROM for game foregrounds including characters. The Foreground Image ROM is composed of chips 7J through 10J. This ROM stores the bit map of characters such as basketball players and cheerleaders.

Background Section. Game backgrounds (scenery) are in the background section. On command, Background Pixel PROM 11D/12D passes a scene to Background Pixel RAM 13E.

How They Produce Video. How do the three sections work together? The microprocessor loads an appropriate image pixel into Foreground or Background RAM. Packet RAM distributes additional foreground image details. Then, under microprocessor control, image pixels are combined at a switcher. (This switcher

Page 15

appears on schematics as the “Color Arbiter”). Switcher 7A/8A/8B/9B determines whether a foreground or background pixel should fill an area of screen.

Color Ram Between the Switcher and the screen, pixel data addresses a Color RAM. This mapping process substitutes color data for pixel data. Color RAM 4A produces three bits each of red, green, and blue data.

Discrete Video DAC Resistors and Transisior. Color RAM output bits arrive at three PNP transistors Q5, Q7, and Q9. Between the buffer and each transistor, each bit is fed through a different value resistor. These resistors determine how intensely each transistor will turn on. The resistors form a discrete digital-to-analog converter (DAC). Three resistors join each transistor’s base to Color RAM outputs. Because the Color RAM produces nine output bits, each resistor corresponds to one bit. The high bit turns the color transistor on the hardest. The middle bit turns the transistor on half as hard. And the low bit turns the transistor on one quarter as hard. The outputs of the three transistors become the red, green, and blue components of a pixel. The game feeds these outputs to a computer monitor for screen display.

Video Blanking. Driven by a clock signal and inverted by gate 1A. The blanking output of NPN transistor Q3 allows or disables current flow through the red, green and blue transistor outputs.

Sound Link The Jamma Interface Board links the game computer to the Sound Board. The CPU Board specifies sounds that the Sound Board must produce. Sound specifications consist of 10-bit, TTL sound-selection and strobe data. An eleventh bit permits the CPU Board to reset the Sound Board.

PAL and PLA Devices What they are. Your game produces many of its control functions in programmable logic arrays. Depending on the type, these chips are shown on schematics as PLAs or PALs. Although they contain certain programmable hardware, these devices are related to PROMS.

No Substitutes. Because PALs and PLAs must be programmed, part substitution isn’t possible. If you need a part you must order in from Bally Midway.

Color Arbiter. The most important PAL is chip 9B, the “Color Arbiter” that presides over video switching. It select a foreground or background video pixel for screen display. This PAL is the only programmable logic array that's directly in the pixel data path. The other PALs and PLDs manipulaie control signals.

Page 16

Foreground Packet Control, The Foreground Packet Control receives many control signals from Foreground Packet Control PLA 11J/12J. Outputs of these two chips feed through latch 11K/12K. Resultant signals control counter 4G/6G/6H, the origin of the Packet Address Bus. This bus addresses the Foreground Packet RAM and the Foreground Staging RAM. Other circuits receive signals from the Foreground Packet Control PLA. Other signals are affected by the Foreground Packet Control PLA. >Foreground Rom Control PLA 14H >Foreground Object ROM Resistor 6K >Latch 5F >Line Buffer RAM Multiplexer 4K >Line Buffer RAM 5D/6D/7D/8D/ and related gates

Foreground ROM Control. Chip 14H is another PLA device. The system latches this PLA’s output at chips 13H, 15H, and 15J. Functions output from the latches address the the Foreground Object ROM . Other signals from PLA 14H affect operation in the following circuits... >Multiplexer 9D/9E >NAND 13J and PD Bus Latch 5E/6E/7E/8E >Foreground Pixel Shift Register 7G/7H/8G/8H/9H/10G/10H >Line Buffer RAM 5D/6D/7D/8D and related gates

Page 17

SIMPLIFIED BLOCK DIAGRAM

Page 18

DETAILED BLOCK DIAGRAM

68000 Microprocessor Discrete Video DAC

FOREGROUND PACKET SECTION N Foreground | Packet RAM

PD ys FOREGROUND BIT MAP SECTION

NOTES:@ =latch, buffer or transceiver. Left side of memory chips indicates address pins; right side, data pins. = multiplexer. Not shown: Control Bus, part of Timebase Bus.

Page 19

Troubleshooting: From Block to Problem

[Symptom [| wn tock ——*d Dead system 1. Fuses; 2. Switching Power Supply; 3. clock chip; 4. monitor; 5. local bus components: MPU 4E, Local RAM 4B/4C, Local ROM 1B/ 1C, 2B/2C, 3B/3C, etc.; 6.capacitor C1; 7. transistor Q3. Background Section: 1. mux 13F/13G/ 14G; 2. Background Pixel RAM 12F/13E; 3. transceiver 12F; 4. latch 11E£/12E; 5. Background Pixel PROM 11D/12D; latch 11C0/12C; mux 11B/12B; latch 10B; PAL 9B. Foreground Packet Section: 1. PLA 11J/1 Mux 2H/3H/4H; 3. Foreground Staging RAM 3U/4J; 4. data buffer 5H; 5. counter 4G/6G/6H; 6. Foreground Packet RAM 5G. Foreground Bit Map Section: 1. Adder 11G/12G; 2. register 6K; 3. OR 7K/13K; 4. latch 5J/6J; 5. PLA 14H; 6. Foreground Object ROM 7J/8J/9J/10J; 7. register 7G/7H/8G/8H/9G/9H/10G/10H; 8. mux 9D/9E; 9. latch 5F; 9. latch 5E/6E/7E/8E; 10. counter 6F/7F/8F/9F; 11. Line Buffer RAM 5D/6D/7D/8D; 12. latch 5C/6C/7C/8C; 13. mux 68/7B

  • PAL 9B; 2. mux 6B/7B; 3. latch 10B. Missing or improper background video

Characters in the wrong 5 2. place; wrong foreground colors

Missing or improper foreground video

Ghost images; confused foreground/background separation Black, vertical lines through image One missing hue

Page 20

Troubleshooting: From Block to Problem (continued) Symptom : Area to Check Some player panel 1. Switches under panel; 2. Connectors 1J2, 1J3, switches don't work 1J4; 3. Buffers 5A, 9A, 13A, 14A; 4. resistor packs RM2, RM3, RM4, RMS; 5. associated capacitors.

  • Connectors 1J3, 1J4; 2. buffers 6A, 10A; 3. | resistors R99 through R106; 4. resistors R107 to R112; 5. associated capacitors. Characters with lines Foreground Object ROM chips 7J, 8J, 9J, 10J. through them or boxes around them Wrong or mixed-up 1. register 6K; 2. XOR gate , 3. late! character images 5J/6J; 4. Foreground Object ROM 7J/8J/9J/10J;
  • PLA 14H; 6. latch 13H; 7. PLA 11J; latch 11K. Rough or “sketchy” Background Pixel ROM chips 11D and 12D. looking background video v Wrong or mixed-up . Multiplexer 1 4G; 2. B P background images RAM 13; 3. transceiver 12F; 4. latch 11E/12E. Missing sounds
Page 21

JAMMANOYSTICK CABLE

[FUNCTION [WIRECOLOR | PIN | PIN [WIRECOLOR [FUNCTION __|

GNDAethGND
2BBLK
[sy [Reo [3c[eo[ss =
+5V[RED] 4DRED+5V
-5VEYELGREEN __| -5V
+12VORN/BLK6FORN/BLK +12V
KEY[eeeKEY
Inc [nc —“‘dTs otk CTNCNC
Inc [no_| » | K[noNC
10 LVIOVELSPEAKER +
NCM_[NcNG

[VIDEORED [RED | 42 | N [GREEN _| vib. GREEN

P WHT VIDEQ SYNC

14 | oRNCNC
NCNC15 sNCNC

GRAY/BLUE T | GRAY/YEL COIN 2 Rrewr

WHT/GRAYUGRAY/RED | PLAYER 2

START START

SWITCH

NC NG

20 X NG

YEL/BLK22 ZzPLAYER 2

PASS PASS

SHOOT SHOOT

NCNCbNC
NCNCcNC
NCNC26 dNC
BLKeGND
GNDBLK28 fGND
Page 22

SNOILVOO1 1WWOSd

BOv) 994

wo30 Was9 (Not a0 1N36 92" 71a) Wwoa0 149

Page 23

JOYSTICK WOOD SPACER DIAGRAM

Page 24

VOLUME CONTROL POT

@ BRACKET ASSY

SHIELD unex

\

SHIELDED VOLUME

\ a CONTROL CABLE

VOLUME CONTROL WIRING

NOTE:

Page 25

Push Button

  • ——~ Black

DIAGNOSTIC (TEST) SWITCH Wht-Grn

Note: Double Sided Tape is Provided to Aid in Mounting Diagnostic (Test) Switch.
Page 26

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 27

C-12610 68000 CPU ASSY

100E-00005-0079

DESCRIPTION.QTYDESIGNATIONPART NUMBER
CAP 10pF AXIAL CER3C71,C55,C720360-00800-0038
CAP 18pF AXIAL CER4C37 ,C38,C73,C750365-00800-0026
CAP 33pF AXIAL CER2C51,C740986 -00800-0309
CAP 47pF AXIAL CER6C45-C500986-00800~2800
CAP 68pF AXIAL CER5€39,C53,C54,C76 ,C770360-00800-0028
CAP 100pF AXIAL CER32C2-C330360-00800-0046
CAP 390pF AXIAL CER4CP1,CP2,C35,C420986-00800-3000
CAP 820pF AXIAL CER18C40,C41,C#3,C44,C56-C690945~-00816-0400
CAP .01uF AXIAL CER155C36, C52,CP7-151, 153-160)0986-00800-2000
CAP 10uF AXIAL TANT3C1,C34,C700986-00800-0700
CAP 470uF RAD ELEC4CP3-CP60B75-00803-0001
RES 10 OHM 1/4W 5%6R79, R80, R82, R83, R85, RB6100E-00005-0011
RES 22 OHM 1/4W 5%3R52,R57,R124100E-00005-0016
RES 47 OHM 1/4W 5%3RYT, R48, R49100E-00005-0025
RES 68 OHM 1/4W 5%3R50,R53,R90100E-00005-0029
RES 82 OHM 1/4W 5%6R60,R96,R97,R120,R121, R123100E-00005-0031
RES 100 OHM 1/4W 5%15R92,R99-R112100£-00005-0033
RES 200 OHM 1/4W 5%7R56, R64,R98,R117-R119, R122100E-00005-0040
RES 470 OHM 1/4W 5%3R81,R84,R87100E-00005-0051
RES 510 OHM 1/4W 5%3R68,R71,R75100E-00005-0053
RES 560 OHM 1/4W 5%3R76 ,R77,R78100E-00005-0054
RES 680 OHM 1/4W 5%1R58100E-00005-0056
RES 1K OHM 1/4W 5%10R1,R3-R6,R12,R67,R70,R72,R74100E-00005-0061
RES 2K OHM 1/4W 5%3R66, R69,R73100E-00005-0068
RES 2.7K OHM 1/4W 5%4R45,R46,R114,R115100E-00005-0071

RES 4.7K OHM 1/4W 5% R2,R8,R11,R51,R54,R55,R59, R61,R62,R63,R65,R88, R89

RES 10K OHM 1/4W 5%34RQ,R10,213-RY4
RES 20K OHM 1/4W 5%1RT
SIP 1K 9 PIN4RMT , RM8 , RMQ , RM10
SIP 4.7K 9 PIN1RM1
SIP 4.7K 10 PIN1RM6
SIP 100K 10 PINyRM2, RM3, RMY , RMS
DIODE 1N41482D1,D2
XSTR 2N4123 NPN2Q1,Q3
XSTR MPSA70 PNP6Q4 ,Q5 06 ,Q7,98,Q9
XSTR TIP110 NPN292,910
COSC 16MHz11D
COSC 20MHz11F
IC 740611A
IC 74ALS20112H
IC 74FO0211F,8K
Ic 74FO413G
IC 74FO8110D
IC 74F3211K
IC 74F7422F,11H
IC 74F86213C,13K
IC 74F157414G,13F,13G,5K
Ic 74FI74112k
IC T4HCT244414A,9A,5A,13A
IC 74SO04215B,15C
Ic 74S7412D
IC T4LSOO15B
IC 74LS0219c
IC 74LS0512E
IC 74LS08115D
IC 74LS20313D,10E, 158
IC 74LS32214D, 130
IC 74LS74515G, 143 ,10F,14B, 14C
IC 74LS86210C,7K
IC 74LS14813K
IC 74L8153211B,12B
IC THLS15768A,7A,4K,4H,3H,2H
IC 74LS16121H,2G

100E-00005-0088 100E-00005-0095 102E-00004-0011 102E-00004-0024 102E-00004 -0026 102E-00004-0045 103E-00002-0005 104E-90001-0007 104¥£-00002-0012 104E-00009-0001 109E-00002-0001 0304-00804 -0007 0986-00803-7600 0459-00803-0015 059-00803-0001 0459-00803-0034 0A59-00803~0030 0304-00803-0059 0459-00803-0003 0459-00803-0031 0459-00803-0004 0A59-00803-0005 0B75-00803-0001 0986-00803-6600 0A15-00803-0023 0304-00803-0010 0986-00803-7400 0A15-00803-0011 0986 -00803-7300 0986-00803-1004 0986 -00803-6100 0986-00803- 1005 0986-00803-9900 0A15-00803~0067 0A59-00803-0006 0304-00803-0021 0986-00803-1003 C-12610 (Cont'd) 68000 CPU ASSY

DESCRIPTIONgryDESIGNATIONPART NUMBER
IC THLS16334G,6G,6H0A59-00803-0008
IC THLS1694OF ,8F,6F,7F0304 -00803-0023
IC 74LS17316K0A59-00803-0009
IC THLS174413B,8B, 15H, 13H0304-00803-0024
Ie T4LS175,115d0304-00803~0025
IC THLS19488G,9H,7H,10G,9G,7G,8H, 10H0304 -06803-0026
Ic 74LS24425H,11A0986-00803-4800
IC 74LS245212F, 3d0986-00803-6400
IC THLS25829E,9D0304-00803-0028
IC THLS273610B,12C,11C, 11K, 10A,6A0986-00803-4700
IC THLS283211G, 12G0304-00803-0030
IC THLS29827B,6B0A59-00803-0010
IC THLS36811G0.A59-00803-0011
IC 7HLS37485E,6E,7E,8E,6C,7C,8C,5C0986-00803-4600
IC 74LS377512E, 11E,53,6d ,5F0A59-00803-0012
PACOUT REV 4 PLA1WdAS9A-26AXL-AXHD
PACNS REV 4 PLA112dA59A-26 AXL-BXHD
ROMCTRL REV 1 PLA114HA59A-26AXL-CXHD
MMCO2B HAL1WF0986-00803-9000
MMCO1A HAL115F0986-00803-8900
MMCO6 HAL1NE0986-00803-9200
MMCO3B HAL115E0986 -00803-9 100
COLARB PAL20L819B0E6 1-00803-0001
IODCD PAL16LB1WJ0B75-00803-0003
MEMDCD PAL16L812d0B75-00803-0004
DTACK PAL16R412K0B75~00803-0005
HSYNC PAL16R4114K0B75-00803-0006
RAM 93419 64X914A0986-00803-9600
RAM 2018 2Kx8 45nS48D,7D,5D,6D0A59-00803-0028
RAM 2018 2KX8 55nS15G0A59-00803-0029
RAM 6116 2KX8 150nS1ag0A59-00803-0027
RAM 6116 2KX8 120nS113E0A59-00803-0014
RAM STATIC 8KX8 150nS14c5340-12278-00
RAM NON-VOL 8KX8 250nS14B5347-12394-00
MC6800014E0304-00803-0051
MC684011E0475-00803-0068
SOCKET IC 16 PIN (.3)21G,14K110£-00001-0003
SOCKET IC 20 PIN (.3)913,23,2K, 14K, 14E, 15E, 11d110E-00001-0005
SOCKET IC 24 PIN (.3)814F, 15F,5G,5D,6D,7D,8D,9B110£-00001-0009
SOCKET IC 24 PIN (.6)213E,4J110E-00001-0007
SOCKET IC 28 PIN (.6)121B-4B, 1C-4C, 11D, 12D, 1E,4A110E-00001-0010
SOCKET IC 32 PIN (.6)473-103110E-00001-9024
SOCKET IC 64 PIN (.9)14E110E-00001-0016
AUTO INSERT PIN .0257332,5354 ,J5,560304-00804 -0009
AUTO INSERT PIN .045"1a0304-00804-0010
FERRITE BEADS18FB1-FB180316-00804 -0002
JUMPERS12JW1-dWi211TE-00001-0003
SWITCH PC MTG2PB1,PB20986-00804-3100
DIP SWITCH1128113E-00001-0004
SNAP292,0100017-00007 -0134
PC BOARD14080-9187 1-E000
LABEL-PCB ASSY ID116-8850-240
GAME ROM12BA-5343-4001-4
GAME ROM13BA-53Y3-4001-5
GAME ROM12cA-5343-4001-6
GAME ROM13cA-5343-4001-7
GAME ROM111DA-5343-4001-8
GAME ROM112DA-5343-4001-9
GAME ROM113A-5343-4001-10
GAME ROM180A-5343-4001-11
GAME ROM19gA=5343-4001-12
GAMz ROM110dA=5343-4001~-13

23 68000 Video Game Board Reference and Parts List

Page 28

SESCAPTON OF CHANGE

an nor re syoaset cru tan ourevr Ponts = INPUT PORTS: DIP SWITCH ween cOnTAOL

Rawi2

rn soxecee secon ae tn man

<a extRsT~ a — > TIME Base

ic Rauiz , AWS sycosct sycose jn. a. PLoussaRD| ‘SEPT 2@ 1907]

Last usens Riz4sc77, ste, 018 Der Nor use: crise femceT 1 oF 19 [Rev

oases sycose ncesee

-Ze- S Fost-ee1349 appecss

cease

rreeze~ 7auses 3 Ph

L % 24uses ‘ & ceurst~ aR

pa t\e | 1 2

crd_RsT extrst~ oe BALLY MIDMAY MFG. CO.

kA. PLoussaRD, ‘SEPT 20 1987, fsnetT 2 oF 19 [REV

Page 29

CONTROL, Data ‘apo amass: lea “oew fee Roni~] BALLY MIDHAY AFG. CO.

  • [NPR 5-22-85] 21301 conqrot, pacsise

appress P pe irs Ase ‘spare cates

Page 30

BALLY MIDWAY AFG. CO.

ah sl 4895 ol ze

i r Pr

Page 31

5-22-89 i 2130] = [NPR

Page 32

2auser9 ‘74Ls279

cet ie0rde7

2ausera oe BALLY MIDWAY AFG. CO.

ea. pLoussanD| ‘SEPT 26 1307 [lene 9 oF a9 [rev

ceurst~. movenur~ cpurst~

SYBLNKI~ 634~ ceurst~ HOVERUFS

coun rene HELE 4 roresRouND weuxe | eon CONTROL

SvaLMKTS Foresrounn ff Reapy~

PACKET

contro. GL voa~ ry SHEET 14 i

sneer 12 om Pxue~ oy

jeracesRan xFER wpe FOREGROUND para. Fearenoune ‘OBJECT reais FORtGROUND PKacore> pacer Havecei9> Ron FLIP PIXEL

FOREGROUND Ran

appness STAGING. D017) TRAIS MULTIPLEXER

fe s0¢or7, 2000131) wouK SHEET 13 ours SHEET 16

SHEET pxpco17>

PDC00" 15)~, PCE<017)~) PPRIO!3> vine~ vipi~

PrecuT FOREGROUND rorccrounn | vine~

DOUBLE PIXEL

LINE ourrur vrD9 BUFFER FoLe~ Tine pase genx cone FPRI

see SHEET 18 WOTES k,n. PLoussaRo| ‘SEPT 281967] se0ee VIDEO GAME BOARD DALY MIDHAY HFS. CO. ne4-91871-Gee0 n951-00114-G166 SHEET 10 OF 19 [REV

Page 33

aR ry2 2

130] Pa

Crewe 5-22-39 |

  • INPR
Page 34

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 35
  • [NPR 5-22-89 [21301

5-22-89] 21301

  • [NPR
Page 36

5-22-89 [ 21301 BALLY MIDHAY HFG. CO.

Page 37

sine_rase Foe 1 poe Verne

7496 crank 9 [ tn

74.817

pauzeten es J vee 4a ne??**8cc| aa

zarsis? « pores DOLLY MIDUAY AFG. CO.

kA. PLoUSSARD| antiee “SEPT 28 19671 6e9@@ VIDEO GaME BOARD

tie SHEET 19 OF 19 [REV

Page 38

Part No. kt Designator

5766-12130-00 5731-11087-00 U1

  • 5700-09006-00 $730-11086.00 U3
  • 5700-09004-00 5400-10320-00 U8
  • 5700-08985-00 A-5343-4001-1 U4 A5343-4001-2 U19 A5343-4001-3 U20
  • 5700-10176-00 5371-09152-00 U11 5430-10322.00 UZ 5340-09878-00 US 5281-09487-00 U16 5281-10043-00 U13 5281-09235-00 5370-09321-00 5281-00215-00 5281-09246-00 5281-09745-00 U15 5370-09156-00 U22, U23
  • 5705-09199-00
  • 20-9229 ¢) 4006-01003-06
  • 4406-01117-00
  • 4703-00007-00 5370-00691-00 5160-10269-00 5060-10396-00 5010-09181-00 5010-09161-00 '5010-09361-00 5010-09358-00 '5010-08998-00 5010-08983-00 Uat U9, U10, U17

UI4 <P - 4m O

lg s 8

gs

:

§ mo <p trp d +a

Audio Board Assembly p/n D-11581-4001

Description

Bare PC. Board IC, D/A Conv, YM3012 Socket, IC, 16-pin (U1) iC, Sound Processor, YM2151 Socket, IC, 24-pin (U3) IC, uProcessor, MC6SB09E ‘Socket, IC, 40-pin (U8) IC, Audio ROM 1 1G, Audio ROM 2 IC, Audio ROM 3 Socket, IC, 28-pin (U4, U19, U20) IC, D/A Convtr, MC1408 Ic, PIA, Mc6a821 IC, RAM, 2016 IC, Dual D Flipflop, 74LS74 IC, 74.8175 IC, Triple NAND, 74LS10 Ic, Op Amp, MC1458 IC, Hex Inv, 74.04 IC, 2-4 Dec, 7418139 IC, Dual Mux, 74.8138 IC, Audio Amp, TOA2002 Heatsink, #6030B Thermal Compound 6-32 x 9/8 P-PH-S 6-32 Hexnut #6 Ext, Lockwasher IC, CVSD, 55536 Transistor, 2N3904, NPN SIP 4.7K & 470pld, 8RBC Resistor, 1.00, 1/2w, 5% Resistor, 220, 1/4w, 5% Resistor, 2200, 1/2w, 5% Resistor, 1K, 1/4w, 5% Resistor, 2.2K, 1/4w, 5% Resistor, 3.3K, 1/4w. 5% PartNo. —Ckt Designator 5010-08991-00 Rt, R4, R5, R11, Rs - R28, R33, R36, R37, R49, R50 R14- R17 R6, R38 R39 R40 RIO ws C1, C3, C4, CB C12, C19, C24 C26, C30 5010-09034-00 5010-09324-00 5010-091 62-00 5010-10258-00 5010-09179-00 5010-09534-00 5040-09343-00 5040-10974-00 5040-09776-00 5040-12006-00 5041-09243-00 5043-08980-00 5, B(17)* €31,C33 13-C15 C2, C34 1043-09844-00 CS 5043-09845-00 C16,C18, C20 - C23, C27 5520-09020-00 X1 5521-10931-00 5551-09822-00 5791-09437-00 5791-10862-04 5791-10862-06 cRI L1-L3. J4 JI, J2, JS J3,

filtering for ICs. [e)

fe}

Description

Resistor, 4.7K, 1/4w, 5%

Resistor, 10K, 1/4w, 5% Resistor, 27K, 1/4w, 5% Resistor, 100K, 1/4w, 5% Resistor, 1M, 1/4W, 5% Resistor, 3.9M, 1/4w, 5% Resistor, 00, 1/4w, 5% Capacitor, 10n'4, 20v, £20% Capacitor, 100ufd, 35v Capacitor, 470pid, 16v; +50, -10% Capacitor, 1000p!d, 16y, 20% Capacitor, 10n{d, 10v-410% Capacitor, 0.01 fd, 50v,+80, -20% Capacitor, 0.1pld, 50v, 420% Capacitor, 470 pid, 50v, 420% Capacitor, 100 pid, 50v, +10% Capactor, 47 ptd, 80v, #20% Capacitor, 1000 pid, 50v, 420%

Crystal, 3.58 MHz Oscillator, 8 MHz Inductor, 4.7 wH, 3A Connector, 20 pin, (Hdr), Rib. Cb Connector, 4 pin (Hd) Connector, 6 pin (Har)

Notes: * 17 capacitors (shown on diagram with "B* symbol) provide +5VDC

All capacitors are ceramic, 50v, axial, unless otherwise noted, All resistors are 5%, 1/4w, Carbon Film, unless otherwise noted.

Page 39

lslslelsla bella ole

x10) rerren

noe] a PELL EEEEE has eb ose TCS 43 v4 mm ced “DATA Eco SNTERPACE DESCRIPTION PAT BER DeSCROTON SPARE GATES. Nores: PART NOURER Jue pe ALL CAPACITORS W/TH""ARE BYPASS AND KAYEA VALUE OF OI. [Erste | OONOT SCALE [aie tooo mo | sunes-oncax Sure comers » 088s | WILLIAMS ELECTRONICS, INC. 3 ‘ 1 ai darises WORK TO. TOLERANCES

2 engae‘Own BYDATE] DIMENSIONSaais Specie24O1N CALIFORW AVECMCAGO
438C34) R48) Ue3, W7, V5, L3 -‘ross i/ze/a7 |“Suown.[oema—"S“aNGUL AR2 Tame
CHECKEG BY DATE [FIRST PROJECT NOBitRt"2164AUDIO SYSTEM SCHEMATIC

gay wt tows | 554 MATERIAL : =

"APPROVALOATE [FSTUSAGE OTYry‘taaiee

ames Car o0s9 [=|

Sound Board Schematic 35

Page 40

Part no.

5678-12455-00 16-8587-975 5010-09358-00 5070-08919-00 5010-09534-00 5043-08996-00 5791-10862-04 5791-10862-06 5791-10862-12 5791-10862-14 5791-10862-18 5791-09437-00 JAMMA INTERFACE BOARD ASSEMBLY pin C-12284

Ckt. Designator

J4, J5, J8 J2, J3 Jg J7 Description

Bare P. C. Board Lable, PCB Indent. Resistor, 1KQ 5% 1/4W Diode, 1N4148 Resistor, 0Q Capacitor, Axial, .1MFD Connector, 4 Pin Connector, 6 Pin Connector, 12 Pin Connector, 14 Pin Connector, 18 Pin Connector, 20 Pin Ribbon

Page 41

[rev] ___cescarron or canoe] EP] | — [NEW PART RELEASE] i212 ,9]

OPPEAKERY OUIDEO GREEN OUT _| COMPOSITE. SYNC Bo oeeteusene

n_2_ RIGHT are START

pare 1 PASS SItiven 2 PASS: R_ {SHOOT AYER 2. ow ananaccvsmvEErnexrmooeel|t Sogo eveusune| Le

SPEAKER INPUT MOLEXO4

SND RESET

FROM VIDEO BOARD J§

MOLEXO6 [7 }-___Vinto our rep, VIDEO OUT GREEN —, VIDEO OUT BLUE = pz SYNC. COMPOSITE SYNC =VSYNC THE INFO CONTAINED ON THIS DRAWING |S CONFIDENTIAL PROPERTY OF WILLAMS ELECTRONICS GAMES, INC_T MAY NOT BE USED OR DISCLOSED [0 OTHERS WITHOUT WRITTEN PERMISSION Oneness ree WILLIAMS ELECTRONICS, INC. WORK TO TOLERANCES: OWN_8y |. DATE] DIMENSIONS UNLESS OTHERWISE SPECIFIED ae sHown | ema, gi cua JAMMA INTERFACE BOARD SCHEMATIC poe | ASS bere 33x $ Bob eractionay eae |

Page 42

COIN BOOK WIRING

TO JAWMA INTERFACE BOARD

GRAY/BLUE 9 NK ON LEFT

‘SOUND BOARD JUMPER CABLE VOLUME CONTROL

fs} a sis|__algisia

v2 an —__ary-vet FROM Lo JAMA Lo} | 43

INTERFACE °

BOARD Lo

8 LL Lo To JAMMA INTERFACE v4

GAN-BLU Fi i

eee TO JAMMA, INTERFACE BOARD J10 ag ala] ae SOUND BOARD CONTROL PANEL WIRING

TO JAMA, INTERFACE BOARD

PLAYER ONE CONTROLS

wre

TO JAMMA INTERFACE BOARD

PLAYER TWO CONTROLS LEFT OPTO BOARD

+5V LEFT-RIGHT (Ai) OPTO 1 ANBAN| | °[[C-A(61) OPTO2 OANRED] [OT LA CIpOPTOS [DIRECTION err 1 o_| | UP-DOWN (At) PTO 4 ¢_[1 U0 (61) OPTOs U-D (C1) OPTOS. ‘ORNViO|_[°—[] DIRECTION BIT KEY|

‘GROUND.

BLUEBLK° No‘SHOOT BUTTON
YEUBLKooNoPASS BUTTON
WHTIGRAYfoNo/PIAYER CRED

Buk

RIGHT OPTO BOARD

+5V LEFT-RIGHT (AT) OPTOT LR (1) OPTO2 LR (Ci) OPTOS DIR ECTION BIT UP-DOWN (At) OPTO UP-DOWN (81) PTO 5 UPA (Ci) OPTO € DIRECTION BIT

(GROUND _ al 99 299 9999990

REDAWHT9NoSHOOT BUTTON
REDIGRAYfoNoPASS BUTTON
GRAYNEL,° No.2-PLAYER CREDIT

BLK

Arch Rivals Interboard Wiring

Page 43

Arch Rivals Interboard Wiring

68000 Video Board to Jamma Interface Board

Note: Pin location is shown for reference only, actual location on the board may be different.

Wht-Blu Left Coin

NC NIC Wit-Vio Tilt NC

Wht-Grn Test J2

Left Shoot Orn-Wht Left Pass

Brn-Yel Right Pass GuvOd OAGIA 00089 eq > = = >

z

m a m7 > ?) m™

BD fe) > a i=}

J3

Page 44

Yel-Blk Yel-Bik Yel-Red

el

oi

ia el

| YelRed

Brn-Blk CS ca

:

N

4 N N/C Grn-Orn

PNG N t=—— Js

GaNNILNOD GuvOd OAGIA 00089

[Bro

[eq

4] Gry i GANNILNOD GuvVOd AOVAYALNI VANES

Arch Rivals Interboard Wiring

NOTUSED 68000 Video Board to Jamma Interface

Board Continued.

Page 45

Parts List

Major Assemblies An blies Included With Your Kit

Boards: FCC Card Rack Assembly C-12892 68000 CPU Board C-12610 Sound Board D-11581-4001 Jamma Interface Board C-12884

Mechanical: Button Assembly, S-Red C-9214-4 Button Assembly, S-White C-9214-5 Analog Joystick, Orange C-9477-15 Wood Spacer 11-909 Switch: White Diagnostic 5643-09556-00 Bracket 01-9180

Cables: Main Harness H-12894 Volume Control H-8866 Video Signal H-12936-1 Power Interconnect H-12933 Jamma Joystick Cable H-12934 Sound Board Jumper H-12758

Decals and Overlays: Marquee, Screened 31-1480-4001-K Center Shelf Overlay 31-1481-4001 Decal Set 31-1482-4001 CRT Shelf Overlay 31-1483-4001 Hole Spotting Decal 31-1494 4003-K Control Panel Cover 03-6250

Page 46

ROM mmar'

68000 Video Board 7J Foreground Image ROM A-5343-4001-10 8J Foreground Image ROM A-5343-4001-11 9J Foerground Image ROM A-5343-4001-12 10J Foreground Image ROM A-5343-4001-13

11D Background Image ROM A-5343-4001-8 12D Background Image ROM A-5343-4001-9

2B Game Program ROM A-5343-4001-4 3B Game Program ROM A-5343-4001-5 2C Game Program ROM A-5343-4001-6 3C Game Program ROM A-5343-4001-7

Sound Board U4 Sound ROM A-5343-4001-1 U19 Sound ROM A-5343-4001-2 U20 Sound ROM A-5343-4001-3

Page 47

JW10

Jwi1

Jwi2 ee

*e

+e

*e

+

ae *e

+

ae

*e

+e

ae

Page 48

F DESIRED, SPOT AND

DRILL HOLES WITH THIS

JECAL BEFORE APPLYING

ZONTROL PANEL DECAL

“|

IF DESIRED, SPOT AND

DECAL BEFORE APPLYING CONTROL PANEL DECAL Ig DIA. rms n>)

Page 49

WARNINGS & NOTICES

WARNING

This game must be grounded. Failure to do so may result In destruction to electronic components.

WARNING This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a CLASS A computing device pursuant to SUBPART J of PART 15 of FCC RULES,which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.

ELECTRICAL BULLETIN: FOR ALL APPARATUS COVERED BY THE CANADIAN STANDARDS ASSOCIATION (CSA) STANDARD C22.2 NO. 1, WHICH EMPLOYS A SUPPLY CORD TERMINATED WITH A POLARIZED 2- PRONG ATTACHMENT PLUG.

CAUTION To prevent electrical shock, do not use this (polarized) plug with an extension cord, receptacle or other outlet unless the blades can be fully inserted to prevent blade exposure.

ATTENTION Pour prevenir chocs electriques ne pas utiliser cette fiche polarisee avec un prolongateur. Une prise de courant ou une autre sortie de courant, sauf si les lames peuvent etre inserees a fond sans en laisser aucune partie a decouvert.

USE ONLY GENUINE BALLY MIDWAY APPROVED REPLACEMENT PARTS.

No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be transmitted, or otherwise copied for public or private use, without permission from the publisher.

© COPYRIGHT BALLY/MIDWAY MFG. CO. ALL RIGHTS RESERVED.