Crazy Climber (Taito Trimline) (72-0001-001 Rev 1)
Crazy Climber (Bandai) (Bandai, 1982) · Document · 26 pages · 6 sections · original scan
TRIMLINE™
“1089 Trade Marks of Taito America Corporanon 72-00001-007 REV +
CRAZY CLIMBER TRIMLINE™
TABLE OF CONTENTS
CRAZY CLIMBER GAME SET-UP
99 7 > Introduction
Game Inspection
Game Installation
“Dip Switch & Volume Control Settings
MAINTENANCE
Cleaning
Fuse Replacement A.
B.
C. Video Monitor Removal
D Video Monitor Adjustments
E. Fluorescent Bulb Replacement
F. Printed Circuit Board Replacement
ILLUSTRATIONS AND PART LISTS
Video and Cabinet Assembly
Coin Door
Coin Door
Switching Regulator & Cabinet Parts
8-Way Joystick Assembly
Control Panel CPU Board “A” & Component List 4
CPU Board “‘B’’ & Component List
Option Switch & Volume Control Locations
Wiring Diagram
PCB Board ‘‘A” Schematic (FOLD OUT)
PCB Board ‘‘B’’ Schematic (FOLD OUT)
GAME SET-UP
INTRODUCTION
TAITO AMERICA’S CRAZY CLIMBER TRIMLINE™ is a skill based video action game. with speech, designed for one or two players.
The object of the CRAZY CLIMBER game is to advance the climber to the top of each skyscraper attempting to avoid the various obstacles. A player can scale up to a total of four skyscrapers. A player accumulates point value for climbing and then receives these points if he is picked up by the helicopter at the top of each skyscraper. If the player misses the helicopter the bonus points are lost and the player advances to the next skyscraper. An additional climber is displayed if the players score reaches 30,000 points (adjustable) .
GAME INSPECTION TAITO AMERICA’S CRAZY CLIMBER TRIMLINE™ game is ready to play when received. However, careful inspection is necessary to insure your game is in perfect condition. Please verify the following before turning the game on.
Examine external parts for chips, dents, or broken parts. Open the service door and examine the following:
- Plug-in connectors to make sure they are firmly seated. Speaker
- Player controls “Printed circuit boards making sure there is no damage to the components.
- Check for loose foreign objects especially metal objects which may cause electrical problems.
- Fuses, making sure they are firmly in the holders.
- Transformer
- Coin Mechanisms
If problems occur or technical assistance is required, contact our Customer Service Department HOT LINE Toll Free 800-323-0666 (except Illinois). illinois phone 312 981-1000 X 215.
The Video Monitor is properly adjusted before shipping, if there are any adjustments necessary refer to the manufacturers operating manual.
POWER REQUIREMENTS TAITO AMERICA’S CRAZY CLIMBER TRIMLINE™game is shipped ready for operation at 120VAC, 60Hz with a power consumption of approximately 250 Watts.
For safe operation it is recommended the cabinet be grounded. This game is equipped with a three conductor power cable. The third conductor is the ground conductor and when the cable is plugged into an appropriate receptable, the game is grounded. The offset pin on the power cable’s three-prong connector is the ground connection.
LOCATION SPACE REQUIREMENTS
Depth - 24” (61cm) Width - 20” (51cm) Height - 54” (138cm) Package Weight - 190 Ibs. (86Kg) INSTALLATION REQUIREMENTS The following precautions should be followed when installing the game.
- Avoid rough handling of the game, the picture tube is fragile.
- Install the game on a level surface.
- Avoid installing the game where it may receive excessive sunlight or heat, to prevent the game from rising internal temperature.
- Do not install in a damp or dusty location.
- For a short time after connecting the power to the game, the picture may be temporarily distorted.
DIP SWITCH AND VOLUME CONTROL SETTINGS
DIP SWITCH SETTINGS TAITO AMERICA’S CRAZY CLIMBER TRIMLINE™ game provides the following option switches. See Figure 9. These options can be found on PC Board ‘“‘B’ Switch B.
SW 1 and SW2 are used for selecting the number of climbers. Switches 1 and 2 are preset at the factory for 4 climbers. cuimBers | swi | swe 3 ofr |” OFF 4 on | OFF 5 ofr | ON 6 on | ON TABLE 1 CLIMBER OPTION
- SWS is not used and should be kept in the OFF position.
- §W4 when in the ON position displays a test pattern and runs through four screens.
- SW5 & SWE are used for coin selection. Switches 5 and 6 are preset at the factory for 1 coin - 1 play.
| COIN SELECTION | Sw5 | SW6 |
| 1 coin - 1 play | OFF | OFF |
| 2 coin - 1 play | ON | OFF |
| 3 coin - 1 play | OFF | ON |
| 4 coin - 1 play | ON | ON |
TABLE 2 COIN SELECTION OPTION
- §W7 is used for adjusting the score at which time an additional _ climber is added. SW7 is present at the factory for 30,000 point
OFF 30,000
50,000 TABLE 3 CLIMBER SCORING OPTION
- SW7 & SW8 are normally in the OFF position unless used for a free play. Then both switches should be in the ON position. SW7
Switches must not be adjusted unless the power is off.
VOLUME CONTROL SETTING
- VR. This option switch is used to control the volume. See Figure
- Volume goes down in turning as the arrow indicates.
MAINTENANCE All games require a certain amount of maintenance to keep them in good condition. A periodic check of mechanical controls would be beneficial to guarantee your game will be profitable.
CLEANING The exterior of the game, all metal parts and all plastic parts can be cleaned with an non-abrasive cleanser. Caution should be used when cleaning the plastic, a dry cloth can cause scratches and result in a foggy appearance.
FUSE REPLACEMENT This game uses six fuses, 5 are located on the Switching Regulator. See Figure 4 for size and part number of fuses. One fuse is located on the Power Supply itself.
VIDEO MONITOR REMOVAL if you need to remove the video monitor, follow the instructions listed below:
It is recommended the game be left ‘disconnected for at least one hour before removing the video monitor. This will probably discharge the video tube but extreme caution is still necessary.
- Remove the control panel by releasing two spring loaded latches. These latches can be accessed through the coin door.
- Disconnect the wiring by separating connector K and all wires to the CRT.
- Remove the three screws from the ‘2’ bracket which leaves the cover glass free to be removed.
- Remove the (4) screws at each corner of the monitor and lift the monitor up and out of the cabinet.
Use extreme caution and do not touch electrical parts of the monitor yoke area with your hands or with any metal object in your hands! High voltages may exist in any monitor, even with power disconnected. VIDEO MONITOR ADJUSTMENTS
The Video Monitor is factory adjusted. If there is a need for readjustments after the game has been shipped, please refer to the manufacturers operating manual.
FLUORESCENT TUBE REPLACEMENT
If you drop a fluorescent tube and it breaks, it will explode! Please use care when replacing.
To replace the fluorescent bulb the control panel must be removed. With both hands turn the bulb toward you and carefully pull out of the lamp socket.
PRINTED CIRCUIT BOARD REPLACEMENT
You may wish to remove the CRAZY CLIMBER TRIMLINE™ printed circuit boards for replacement or service. Follow the procedure below.
To remove the “A” Board (08-00005-002) and/or the ‘‘B’” Board (08-00005-003) slide the double layered board set out of the guides.
This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. As temporarily permitted by regulation it has not been tested for compliance pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference. Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.
VIDEO AND CABINET ASSEMBLY
TAITO
| (TEM | PART NO. | DESCRIPTION | REFERENCE |
1 45-00001-001 | Lock Assembly 2 42C00047-001 | Back Door 3 61B-00027-001) Grill Door 4 41D00004-001 | Cabinet Assembly 5 59-00008-001 | Clamp 6 61A00020-001 | Service Switch Bracket 7 29-00002-001 | Service Switch 8 61B00038-001 | Speaker Grill 9 21-00002-001 | Speaker 10 07D00022-001 | Coin Funnel WW 61C00033-001 | Cash Case
| 12 | 500086 | Cash Box Bracket (Top) | . | |
| 13 | 500087 | Cash Box Bracket (Bottom) | ||
| 14 | 500091 | Counter Bracket | ||
| 15 | 130000 | Counter | __ | |
| 16 | 400050 | Cash Box | ||
| 7 | 500089 | Cash Box Door | ||
| 18 | 600006 | Lock & Key | | | _ |
19 61D0002-001 | Coin Door 20 61D00040-001 | Coin Door Frame
| 21 | 61C-00018-001| Marquee Retaining Bracket (Upper) | __ |
22 47B00006-001 | Marquee 23 61D00019-001 | Marquee Retaining Bracket (Lower) ee _ 24 42B00046-001 | Fluorescent Panel 25 29-00003-001 | Starter 26 26-00005-001 | Starter Socket __ 27 26-00004-001 | Lamp Socket 28 27-00001-001 | Fluorescent Bulb 29 18-00002-001 | Transformer, Ballast (120V, 60Hz) 30 61B00017-001 | Cover Glass Retaining Bracket 31 47-00004-001 | Cover Glass 32 63C00009-001 | Monitor Shroud 14” __ 33 42D00019-001 | Monitor Mounting Panel 34 07-00017-001 | Monitor 14” Color *35 36-00005-001 | Counter Drive Credit Board AAMS50012 *36 25-00014-001 | 10 Position Edge Connector *37 61A00014-001 | Credit Board Bracket
- Item not shown on Figure 1.
VIDEO AND CABINET ASSEMBLY
TAITO
| ITEM | PART NO. | DESCRIPTION | REFERENCE |
| 1 | 07-00027-001 | Inner Pane! With Levers Sub Assembly | 404429 | |
| 2 | 54-03013-001 | Nut #8-32 | 400-8 |
- 09-00017-001 | Custom Harnes Assembly (SGL Coin)
- 09-00017-002 | Custom Harness Assembly (Dual Coin) 3 54-03011-001 | Nut #4-40
| 4 | 61-00043-001 | Wire Key Holder | 904722 |
| 5 | $3-00014-001 | Switch Cover | 904762 |
| 6 | 51-02052-001 | Screw #6-32 x */:s SL ph | 100-6-3 |
| 7 | 23-00001-001 | C.R.E.M. Coil Assembly | 404354 |
| 8 | 51-02052-001 | Screw #6-32 x “/1e SL ph | 100-4-12 |
| 9 | 59-00019-001 | Retainer | 900651 |
| 10 | 28-00029-001 | Silver Switch Wire for U.S. 25¢ | 904710-1 |
| ab | 29-00007-001 | Switch | 904845, |
| 12 | 61-00044-001 | Coin Chute | 904701 |
| 13 | 61-00045-001 | Coin Return Box | 904598 |
| 14 | 61-00025-001 | Switch & C.R.E.M. Coil Bracket Assy | 404428 |
| 15 | 59-00018-001 | 25 Acceptor | 5301-10 |
| 16 | 61-00046-001 | Rod Retainer | 905115 |
| 17 | 51-02051-006 | Screw 4-40 x % SL ph | 110-4-6 |
| 18 | 27-00003-001 | Miniature Bayonet Base Lamp | 904717 |
- 26-00006-001 | Lamp Socket
| 19 | 27-00003-001 | #47 Lamp (6.3 Volt) | 904716 |
| 20 | 61-00048-001 | Coin Inlet Chute | 904418 |
| 21 | 61-00047-001 | Right Half of Coin Inlet Chute | 904594 |
| 22 | 54-00001-001 | ‘‘U” Type Fastener | 904712 |
| 23 | 51-02051-006 | Screw 4-40 x % SL ph | 116-4-8 |
| 24 | 29-00006-001 } Slam Switch Assembly | 904704 |
- Item not shown on Figure 2.
COIN DOOR
COIN DOOR
TAITO
| ITEM | PART NO. | DESCRIPTION | REFERENCE |
| {1 | 61-00042-001 | Coin Door Only (2 Goin) | 404341 | |
| 2 | 07-00023-001 | Coin Return Button Assembly For U.S. 25¢ Coin | 404348-1 | |
| 3 | 63-00015-001 | Coin Return Button | 904591 | |
| 4 | 79-50004-001 | U.S. 25¢ Price Decal | 904703 |
5 63-00016-001 | Goin Return Button Cover for U.S. 25¢ Coin
| 6 | 07-00025-001 | Lock Assembly | 904707-1 |
| 6A | 07-00025-001 | Lock Assembly | 904707-1 |
| 7 | 51-01051-003 | Screw #4 x 5/16 SL ph Type B | 345-4-5 |
| 7A | 51-01051-003 | Screw #4 x */:6 SL ph Type B | 345-4-5 |
| 8 | 63-00011-001 | Coin Button Housing | 904588 |
| g | 51-02051-002 | Screw #4-40 x Ys SL ph | 325-4-4 |
| 10 | 63-00012-001 | Coin Return Bezel | 904590 |
| 1 | 63-00013-001 | Coin Return Cover | 904599 |
| 12 | 61-00040-001 | Coin Door Frame 1156 x 13% | 904581 |
Mounts in a 10% x 12%/15 Opening
| 13 | 54-01005-001 | Hex Nut %4-20 | 406-416 |
| 14 | 51A03003-113} Carriage Balt | 904734 |
| 15 | 07-00026-001 } Lock Arm Assembly | 404357 |
COIN DOOR
SWITCHING REGULATOR & CABINET PARTS
TAITO
| ITEM | PART NO. | DESCRIPTION | REFERENCE |
| 1 | 800010 | Switching Regulator PCB Assembly | AAM60009 |
| 2 | 998702 | Shield Box | AA013613 |
3 22B-00001-001] Power Line Filter 4 26-00003-001 | Service Outlet 6 24-00002-002 | Fuse, 1.5 AMP, 3AG, Slo-Blo, 250V 5A 24-00002-001 | Fuse, 3AMP, 3 AG, Slo-Blo, 250V 6 24-00001-001 | Fuse Holder 7 35-00001-001 | Barrier Strip, 8 Position 8 42-00034-001 | Power Board 9 61-00030-001 | Switch, Interlock 10 29-00004-001 | Toggle Power Switch It 35B-00082-001} Insulating Shield
| 12 | 500025 | Toggle Switch Bracket |
13 18A-00001-001} Isolation Transformer
| 14 | 998962 | Noise Filter | AAT61017 |
| 15 | 998703 | Shield Cover |
16 61B00003-001 | Bracket Interlock Switch
SWITCHING REGULATOR & CABINET PARTS
8-WAY JOYSTICK ASSEMBLY
TAITO
| ITEM | PART NO. | DESCRIPTION | REFERENCE |
| 1 | 400026 | Color Ball | BP0S0003 |
| 2 | 500153 | Control Lever | ywo20001 |
| 3 | 400030 | Mask | RT090009 |
| 4 | 500154 | Joystick ‘“Base"’ | RFO30002 |
| 5 | 390041 | Plain Washer | AAL61027 |
| & | 370007 | Spring | RFO60001 |
| 7 | 500155 | Joystick “Base” | RF030003 |
| 8 | 500156 | Center Ball | RFO20005 |
| E} | 500157 | Center Ball Cover | RFO3OOU4 |
| 10 | 500158 | Collar | RFO20002 _ |
| 11 | 500159 | Actuator Push Plate | RF030007 |
| 12 | 500160 | Push Plate Guide | RFO30005 |
| 13 | 500161 | M.S. Base | RFO30001 |
| 14 | 390042 | Spacer | RF020003 |
| 15 | { 020503 | Micro Switch | AA052532 |
| 16 | 199010 | Insulator V Type | AA019504 |
| 17 | 500162 | Block | RF020006 |
| 18 | 390043 | Snap Pin | |
| 19 | 500163 | Lock Plate | RFO30006 |
8-WAY JOYSTICK ASSEMBLY
CONTROL PANEL ASSEMBLY
TAITO
| ITEM | PART NO. | DESCRIPTION | REFERENCE |
| 1 | 998590 | Push Button Assembly (White) |
2 47C00003-001 | Control Panel (Aluminum) 3 42000033-001 | Control Panel (Wood)
| 4 | 020501 | Micro Switch |
| 5 | 199010 | Insulator |
| 6 | 355000 | Pal Nut |
| 7 | 500018 | Switch Button Bracket |
8 63A00021-001 | Mask
| 9 | 850042 | Joystick Assembly (8-Way) | UWK00005 |
10 63A00020-001 | Knob & Shaft W 61A00015-001 | Strike Hook
CONTROL PANEL ASSEMBLY
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
CPU BOARD “‘B” & COMDONENT LIST
Taito Taro
| ITEM| PART NO. | | DESCRIPTION | REFERENCE | ITEM | PART NO. _| DESCRIPTION | REFERENCE |
| 1 | 79-00013-001 | PC Board Sticker | 31 | 46-00001-107 | Rom 7 CC-7A 2732 | |
| 2 | [29-00008-001 | Dip Switch DDS-8 | AAO 52566 | 32___|16-00001-108 | Rom 8A P-Rom CC-8 2732 | |
| 3} | 26-00001-024 | IC Socket 24P | AAO 55787 | 33 | 16-00001-009 | Rom 9 P-Rom CC-9 2732 | |
| 4 | _[26-00001-040 | IC Socket 40P | AAO 55612 | 34_| | 16-00001-010 | Rom 10 P-Rom CO-10 2732 |
| 5 | | 25-00004-001 | PC Board Conn, | 35 _| 16-00001-011 [ Rom 11 P-Rom CO-11 2732 |
PON364J0404G 36 _ | 16-00001-012 | Rom 12A P-Rom CC-12 2732 6 | 25-00021-001 [Angle Pin Header PS SOPA | AAG 55154 137 | 16-00001-113 | Rom 13A P-Rom CC-13 2732
| 7 | _{11-60001-202 | Variable Res 2K Pt | 38 | | 12-10002-102 | C1 Cap-Ceramic 0.00uf50V | AAT 41399 | ||||
| 8 | _|13-00002-001 | Diode 181588 | ae | 39 | 12-10002-104 | C2 Cap-Ceramic O.1ufS0v | AAT 41672 | ||||
| 8 | 15:50003-001 | OP Amp. ME S712 | BATSON | 40 | _[12-40001-105 | 63 Cap, Tantalum tufasv__| | AAT 41425 | |||
| 10 _| 15-20000-001 | 1¢ 1 LS IC 74L800 | AAT 33001 | 41 | | 12-40001-106 [ C4 Gap, Tantalum 10uf25v_ | AAT 41430 | ||||
| 1 | 15-20002-001 | IC 2 Ls IC 74L 802 | Sg | 42 _| 12-50001-476 | 65 Cap, Tantalum 47uf36V_| | AAT 41657 | ||||
| 12_[15-20004-001 | IC 3 LS 1c 741804 | AAT 33005 | [a3] | 12-20007-107 | 6 Cap, Electrolytic | ||||
| 13 | 15-20008-001 [ IC 4 LS Ic 741808 | AAT 33009 | 25V8 100uf | AAT 41036 | ||||
| 14 _ | 15-20032-007 | [iG 5 LS IC 7ats32 | AAT 33027 | 44 | 12-20001-477 | G7 Cap, Electrolytic | ||||
| 15 | 15-20042-001 [1 6S 16 TALSHa | AAT 33032 | 20v8 afi | sd | ||||
| 16 | _[15-20074-001 | 1¢ 7 Us IC 74874 | aat 33051 | | | [45 | 11-00001-2211) | RRs, Carbon | ant i749 | |
| [17 | | 15-20125-001 | [IC 8 LS IC 7aLst26 | AAT 33089 | eT | iionoott02 | TR 2 Res, Carbon 1K | TAT SI7éS |
| 18 | _{16-20138-001 | 1¢ 9 LS Ic 748138 | AAT 33096 | a7 | [0000-103 Res, Carbon 10K | ae | ||
| 19_[120139-001 | 1010 LS 16 7418139 | AAT 33097 | ae—| | tetoorres | ba | Roo. Carbon 18K | AAT EITSE | |
| 20 | 15-20157-001 | IC11 LS IC 74LS157 | AAT 33112 | 49 | 11-00001-273 | R 5 Res, Carbon 27K | AAT 51799 | |||
| 21 _ | 15-20161-001 | IG12 LS IC 7418161 | AAT 33116 | 50 | 11-00001-473 /R 6 Res Carton 47K | AAT 51605 | |||
| 22_|16-20174-001 | 1013 LS IC 7418174 | AAT33127 | | FC ongocaoa | a7 Res, Carbon 100K | TAT 61603 | |||
| 28 _{iis 0269001] | IGi4 TTL IC 74259, | a | 62_| | 11-00001-204 [ R 8 Res, Carbon 200K | _| AAT 51820 | ||
| 24 | 15-20273-001 | 1C15 LS IC 74LS273 | AAT 33170 | 53 | 11-00001-304 | R 9 Res, Carbon 390K | AAT 51827 | |||
| 25 | 15-20367-001 | 1C16 LS IC 74LS367 | AAT 33203 | 54 | 11-00001-824 | R10 Res, Carbon 820K | ‘AAT 51835 | |||
| 26 _1 16:20968-001 | (C17 L816 7418988 | BAY 38204 | 55 | 11-50007-010 | RBT Resistor Block tohmx®_| | AAT 55036 | ||||
| 27 | 15-20393-001 | 1C18 LS IC 74LS393 | AAT 33220 | 56 | 15-00009-001 | custom Module | T | ||||
| 28 | 15-10003-001 | 1C19 Static Ram MB8114NL | AAT 33156 | | 57 | 15-44066-001 | 1C22 C Mos IC MC14066 | ‘AAT 36067 | ||||
| 29_[15-50004-001| | 1620 Op Amp LM3=00 | | AAT 31011 | 38 _| 15-20245-001 | 1623 LS IC 7418245 | AAT 33157 |
30__| 75-60008-001 | 121 Sound 1¢ AY-3-8910 | AAT 32165
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
OPTION SWITCH & VOLUME CONTROL LOCATIONS
on
off
Board “B”’
L
Game
PC. Boar Assy. 08 - 9e005-00) (Boaro | 02)
COUNTER
23% ila <j t S&T8TO/D RE
Same, suo Bio- Rovae Gee S10- Bue- 203 wee. pare Ba. [Pere] ter
| ag
i Zoamena)> EEE elo WIRING DIAGRAM
NOTES
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
NOTES
TAITO AMERICA CORPORATION 1256 Estes Avenue, Elk Grove Village, |. 50007 Telephone (312) 981-1000 Telex 25-3290