CATHODE RAY TOMES

Pace Car Pro

Pace Car Pro (Electra Games, Inc.) · Manual · 36 pages · 34 sections · original scan

Page 1

INSTRUCTION MANUAL

HINT RoR Bi0u Steg

ELECTRA GAMES, INC. 2570 United Lane Elk Grove Village, Illinois 60007

Page 2

INTRODUCTION

"Pace Car Pro" is the first racing game in which four players can share in the excitement of a simulated high speed race.

The game has been designed to provide the same excitement for one, two, three, or four players, since a "robot" pace car provides built-in competition. To add to the excitement, there are realistic motor sounds (one for each car), crash sounds, an infield that actually causes the cars to "slow" down, anda "joystick" control for each car that controls speed, direction, and braking.

When set for single coin per player pricing, Pace Car Pro has the potential to increase income. It is the first game with the capability of taking in one dollar per play.

Each "Pace Car Pro" game undergoes hours of testing before it is judged acceptaz! for shipment. Thorough component testing involving thermal cycling, final inspec and testing - 24 hour operative testing of individual electronic assemblies and color television, and finally a 24 hour test for the complete game. Every game must pass all tests before it can be shipped.

The game has been designed with ease of servicing in mind. All electronic pes modules and the color television are accessible by removing the cabinet top. The entire game electronics is contained on two plug-in logic printed circui: ards, a plug-in power supply board, and a color adjust board.

Despite all testing and precautions taken, malfunctions sometimes occur. Refer to the trouble-shooting guide to isolate the problem, and contact tho distributor from whom the game was purchased for repair or replacement instructions. "Do hot attempt to perform repairs on any in-warranty printed electronics boards, as the warranty will be voided."

Page 3

Except as hereinafter stated, Electra Games, Inc., warrants the color television and the modular electronic printed circuit boards used in "Pace Car Pro" to be free from defects in material or workmanship under normal use. Our obligation under this warranty is limited to making good at our factory any parts thereof which shall within: ‘

96 days ~ color television 1 year - modular electronic printed circuit boards

after delivery of such product be returned to us, and which our examination shall disclose to our satisfaction to have been thus defective will be exchanged or repaired without charge to the owner: ver, transportation costs incidental to replacement or exchange of such parts shall be borne by the owner.

This warranty does net extend (1) te any of our products which have been subject

or to use in violation of instructions furnished by us, (2) to units which have repaired or altered by anyone o than us, (3) to cases where the manufacturer's date code or the serial number of the product has been removed, defaced, or chan

This warranty is in lieu of all warranties expressed or implied, and no representative or person is authorized to assu for us any other liability in connection wi the sales of our products.

ELECTRA GAMES, INC. 2570 United Lane Elk Grove Village, Illinois 60007

Page 4

CABINET ACCESS INFORMATIC

The "Pace Car Pro" cabinet is constructed of solid core plywood and consists

of three basic parts: the Base, Top, and Control Panel.

  • Access into the Base is thru the Bottom Access Door; the keys to this door are located in the Instruction Manual envelope. Access into the Base 1s necessary to reach the Cash Box, Coin Chute, Power Cord, or to remove the Control Panel.
  • Removal of the Top allows access to all of the Electronics Modules, Coin Equipment, and the Color Television. The keys to the Top are also located in the Instruction Manual envelope.
  • Removal of the Control Panel is only necessary for access to the "Joysticks" or for additional door opening clearance. Tor Control Panel removal instructions, see section entitled "Door Opening Clearance

TOP REMOVAL:

Locate the two keys for the cabinet top (in unlock top. (Top is unlocked with both ke mh anual envelope), and tn horizontal position.)

REFER TO FIGURE 1 FOR THE FOLLOWING:

. Grip Cabinet top at lower front edges and lift up several inches (this will disengage the "U" channel which locks the Front Panel in position.)

. Push the Top back several inches, until it clears the Front Panel, and then set it down, so that Top is again resting on Cabinet.

You should then move to rear of Cabinet and pull Cabinet Top back while holding it securely.

Note: When mounting Cabinet Top, the reverse procedure should be followed. The two bolts at lower rear of Top assembly must be aligned with the mating brackets at the rear of Base when mounting Top. (Refer to Figure 1 - C.)

INSPECTION AND PRELIMINARY SET-UP:

With the Tap removed, a thorough inspection for shipping damage should made. ingpect complete Cabinet (Base, Con Pe op) for obyv damage. If any damage is discovered, contact the carrier imme ly. Then contact the distributor from whom the game was purchased for repair or replacement instructions.

Page 5

cabinet top —_,_

control ‘panel

cabinet base ——7"

= c. = Figure 1- CABINET TOP REMOVAL

Page 6

INSPECTION AND PRELIMINARY SET-UP - CONT'D.:

Inspect the Color Television for any obvious damage, then inspect the power supply unit (located behind the television). The power supply P. C. module should be connected and securely in position. (Refer to Figure 2.)

Inspect the Logic Module Chassis. Remove the Chassis Cover, and check that both Logic Boards (EG1000-A and EGI000-D) are securely in position, and connected into their respective edge connectors. (Refer to Figures 2 an

Check connections to the Color Adjust P. C. board, mounted on the Logic Module Chassis. (Refer to Figure 2.)

Check the Coin Mechanism to see that it is properly mounted. Insert several old and new coins, into the Coin Mechanism. No genuine coins should be rejected. Operate rejector mechanism and check for any "binding".

oi TE

, control cable

logic module chassis

power supply module

connector strip

Figure 2

Page 7

EG 10 ee Digital Yogic module

EG 1000 A Analog logic module

chassis cover

a7]

Fiaure 3 a

Page 8

DISASSEMBLING SHIPPING PALLET:

The keys to the Bottom Access Door are located in the Instruction Manual envelope. Locate the keys and remove the Access Door.

Unbolt the game fror inside Base of Cah Pallet by removing four 3/8" bolts from

Install the four Adjust into threaded "T" nuts

in Cabinet Base. Gee Figure

DOOR OPENING CLEARANCL:

Clearance dimensions of "Pace Car Pro" completely assembled are:

33" wide X 38 1/4" deep X 57" high

Note: If game will not clear door opening, the should be disasse s follows: ntrol Panel

Disconnect Control Cable frefer to Figures 2 and 4). Control Cabie is connected to the Interconnect Printed Circuit Board.

While holding Control Panel, remove two 3/8" bolts whien secure the Control Panel to the Cabinet Base.

Clearance dimensions of the game with Control Panel removed are:

33" wide X 30 1/4" deep X 57" high

Note: If additional clearance is required, remove Cabinet Top. (Reter to "Top Removal!" and Figure 1.)

used to remow ct Control ¢ Replace Control Panel by reversing procedure (Refer to Figures 2 and 4.) Be sure to re-c

SETTING UP THE GAME:

Game must be leveled by adjusting the four legs previou sly in the cat

Note: if Gare height sufficient to allow a the bottom of the Base. carpeted iloor, irculation in ° a
Page 9

SETTING UP THE GAME - CONT'D.:

Push the Power Cord Plug, located inside the Game "Base" thru the hole in the _ back of the base. (Strain relief on Power Cord restricts cord from being pulled entirely out of Base.)

Note: Pace Car Pro is shipped set to operated om 120 volt 50/60 Herz Power. To set-up for 240 volt 56/60 herz:

red/blk

yel/bik

120 volt 50/60 Hz 240 volt 50/60 Hz

Plug the Power Cord into the proper receptacle (120 volt - unless modifie= as directed), and turn on Power Switch located at the lower rear of the bas After approximately a 15 second warm-up period, the display shown in Figure - vill appear on the cathode ray tube.

GAME OPERATION AND SEQUENCE:

Definitions:

its establi Standby Condition Game power on, no Cre

Credit Condition - One or more Credits establi one Quarter deposited.

Play Condition - Start Button activated, C

Page 10

stoners Ny}!

bottom access door

4+— adjustable legs

Figure 4

Page 11

grass (green area)

track

lap counters

fi ~™N

red yellow violet

violet car

” pace car

pace car lap “hash marks

red car start/finish line blue car Figure 5

Page 12

GENERAL:

The Pace Car (green blip) serves a two-fold purpose:

ND It performs the function of a “built-in” opponent making it possible for one person to pley.

  • It operates as a Game Timer which determines the duration of each play (race).

The four opponent cars are the Red, Yellow, Violet, and Blue blips. These cars are controlled by the four color keyed “Joysticks” on the front panel. Each "Joystick" controls the Speed, Direction, and Braking of its respective car. The "Joystick" is mechanically biased to return to center position.

The four ‘Lap Counters (color keyed to each car) show the progress of each c:: advancing - one count - for each completed lap. One lap is completed wne car is moved counter-clockwise from the Starting line, completely around t>+ track and back to the starting line, (in Play Condition) .

The Pace Car laps are indicated py "Hash" Marks displayed just below the Lap Counters. The total pace car laps to be completed are shown at the b. of the race, and then one is subtracted for each lap completed by the Pace until the race ends.

STANDBY CONDITION:

The Pace Car is moving about the track in a counter-clockwise direction.

The four Opponent Cars (Red, Yellow, Violet, and Blue) are displayed ‘st tc tas left of the Starting Line.

The four Lap Counters show the results of the previous race.

The Pace Car Lap Indicator is not operational at "Standhy"; therefore no Pace Car Laps are displayed.

If the "Joysticks" are moved, the four Cars will show some movement within limited area. oo

CREDIT CONDITIO:

One Quarter deposited - -

The Pace Car is moving about the track and now a Motor Pace Car moves.

Page 13

CREDIT CONDITION CONT'D,:

Only the Red Car is displayed just to the left of the Starting Line, and an idling sound is heard. The four Lap Counters are re-set to "Zero". The Pace Car Las

  • Indicator shows six (6) laps to be completed. The "Joystick" allows movemern: within a limited area, the s held to the right (direction of race) the Motor Sound "Revs" to a higher

PLAY CONDITION

The Start Button is depressed ~ i The Pace Car is stopped and is now displayed just behind the Red Car at the Starting Line, (which is now flashing on-and-off}. The Lap Counters still real "Zero" and the Pace Car Lap Indicator shows six (6) laps to complete.

The Red "Joystick" is held to the right with the Motor Sound racing: the Line szops flashing and the race begins.

With the Red "Joystick" held to the right, the Red Car begins to move to the + picking up speed as it heads for the turn. As the Red Car comes into the tur "Joystick" must be moved upward. The Red Car now foliows the Track upwa the diagonal stretch of the Track, the "Joystick" st be moved up and to tn This procedure is followed for each stretch of Track; i the "Joystick" is in the direction that the Car is to be moved. When the Red Car crosses t Finish Line for the first lap, the Red Lap Counter advances to "1", ando “Hash" Mark is subtracted for the Pace Car. This action continues for six (€

right

Figure 6

Page 14

pricing label extended

indicator

blue | jo red ck joystick

_ yellow joystick

jame start Sad violet joystick

Figure 7

Page 15

PLAY CONDITION CONT'D.:

At the end of the sixth lap, if the Pace Car Finishes first, all action "Freezes' for several seconds with the Pace Car at the Finish Line: the Game is then " Re-set to "Standby Condition".

if the Red Car reaches the Finisn Line before the Pace Car, all action "Freezes" for several seconds, with the Red Car at the Finish Line: except in this insta the Game is automatically transferred into Extended Play Mode; the action again and continues for approximately 15 seconds, at the end of which the g Re-set to "Standby Condition".

During "Play Condition", as the Car is moved about the Track, if contact is between the Car and the "Grass" (green area), the car is "Slowed Down" sub tially. The car must be kept in the Black Track area to operate at "Maximum

When several Cars are played, if contact is made be activated and the Cars are "Bumped" Apart. Cars, a Crash Sou

Each of the four Cars has its own Motor Sound, slightly different from the ot three. The PaceCar Motor Sound is activated only whe e Red Car races (S$: Player Mode).

PRICING AND ADJUSTMENTS:

“Pace Car Pro" is shipped with the following factory

Pricing - One player per quarter

Pace Car - Six laps and Minimum Speed (2 1/2 minute race)

PRICING:

The Game is shipped with a “Coin Mechanisms, inc." ~ Single Coin Ov Rejector. The Coin Mechanism can be replaced by a Nickle, Dime or Frrsign Coin Mechanism.

There are Two Pricing Options: One Player

The pricing switch on the EG1000-D digital logic board is shown set for Players per Coin" (see Figure 8). By setting the Pricing Switch tot Player per Coin" position, Pricing is automatically changed.

e label in positio Two Pricing Labels are suppi Pl ‘Quarter. Tape the appro (See Figure 7.)

Page 16

horizontal centering (game display)

EG 1000-D digital logic board

6 laps

< pace car » lap switch

¢

8 laps

1 player per coin

pricing switch

2 players per coin

bias (game display)

Figure 8

Page 17

ADJUSTMENTS:

Pace Car laps - The Pace Car may pe set-up to complete Six (6) or Eight (8)

  • laps. The Game is shipped set for Six (6) laps. To set for Eight (8) laps, the Pace Car Lap Switch on the [G1000-D Digital Logic Board must be switches to the "Fight" lap position. = Figure &.)
Note: Refer to Figure 9 for the following adjustments. Study carefully before making adjustments so as not to adjust the wrong control.

Pace Car Speed - The Pace Car Speed is adjustable so that the Game duration be changed between 1 and 2 1/2 minutes. Tne Game ts shipped set for 2 1/21 Control VR24 on the EG1000-A Analog Logic Board changes Pace Car Speed.

Sound Output - The Game has two Sound Qutput Controls:

VR21 - Controls the Output of all Sounds

VR22 - Controls the Output of the Pace Car Sound - only

The following adjustments should be changed only if necessary, since they are factory set and adjustment should not be uired.

Horizontal Size of Cars -

VR-13 - Red Car VR-14 - Yellow Car VR-15 - Violet Car VR-16 ~ Blue Car

(Adjust so that car width is slightly less than its height.)

Shape of Cars -

VR-9 - Red Car VR-10 - Yellow Car VR-l1 - Violet Car VR~-12 - Blue Car

{Should be adjusted after horizontal size is set.)

Position of ail Four Cars at “Standoy" - VR-19

To Adjust - Ll) “Joysticks" must be in vertical "

  • "Joystick" amplifiers (all four) s+ positic Id be adjust

Aciust VR-19 so that all Four Cars Starting Line.

Page 18

pace car speed

pace car positioning (diaganal section of track)

sound output (all sounds) sound output(pace car only)

ae 2 VR21 VR22 horizontal size of cars

position of all four cars

‘vertical ramp (factory adjust)

violet. a blue

EG1000-A ANALOG LOGIC BOARD

Figure 9

Page 19

1 Position of all f¢ ndby" ~ VR-20 Cars at "Sts

To Adjust - 1) “loysticks" must be in the vertical rest position.

  • "Joystick" amplifiers (all four) should be adjusted.

Adjust YR-20 so that the Two Cars closest to the "Checkered" Start Line are 1/2 inch from the line.

in the Diagonal Section of Track - VR-23 © Car travels thru center of diagonal section of Track.

ce affe a by adjustment of Pace Car Speed VR-24.)

ck Amplifier Adjustment ~ Refer to Tigure 10 for the following. The "Joystick" ifier Adjustment is factory set and normally require readjustment only when the the EG1000-A Analog Board is changed, or if any of the "Joysticks" are replaced. There are two controls for each car. The controls adjust the voltage at the output of the "Joystick" Amplifiers. The purpose of the adjustment is to minimize drift of each car in the vertical and horizontal direction when the "joystick" is in the upright "rest" position, and to standardize the speed of the cars. The adjustment

is relatively simple, when using the " oystich” Amp Adjustment Board, which is

available from your distributor

To Perform the adjust All "Joystick must be in the upright "rest" position, "Snap" the _ "Toystick to return it to center "rest" position, The "Joysticks" should not be moved while making these adjustments.

  • Game power should be "On" ~ Game in "Standby Condition."
  • Observing correct polarity, connect the Black and #1 Red clip leads to C173, 250 mfd capacitor as shown in Figure 10.’ All adjustments will be ma those leads connected.
  • Connect th Red clip lead to the Positive (top) side of C4 (1 mfd capacitor). (See figure 10.) Adjust VR-1 until the center LED indica illuminated.
  • Move Red clip lead to Positive (top) side of CS (1 mfd capacitor). Adjust VR-2 until the center LED indicator is tluminated.

The Red "Joystick" amp is now adj:

  • Move the "2 Red clip lead to Positive (top) side of C31 (1 mfd capacitor), Adjust VR-3 until c er LED indicator is illuminated.
  • Repeat with C32 and VR-4 to finish adjustment for Yellow "Joystick" amp.
  • Repeat with C88 and VR-5, then C89 and VR-6 for Violet "Joystick" amp.
  • Repeat with C13 and VR- hen Cll4 and VR-8 for Blue "Joystick" amp.
Page 20

"Joystick" Amplifier Adjustment, Cont'd. -

This completes the "Joystick" Amplifier Adjustment.

Horizontal Ramp Adjustment - The horizontal ramp control (VR-17) adjusts the _ voltage of the horizontal ramp. This control is factory set and should not be r adjuste: since Game operation will be adversely affected. Refer to Service Manual for Zurther information.

Vertical Ramp Adjustment - The v cal ramp control (VR-18) adjusts the peak ~zltage of the vertical ramp. This control is factory set and should not be readjusted, since Game operation will be adversely affected. Refer to Service Manual for further information.

Game Display Bias Control - This control ‘is located on EG1000-D Digital Logiz Board. (Refer to Figure 8.) Adjusts horizontal and vertical sync input to the 7 input. Adjust for best picture.

Game Display Centering - This control is located on FG1000-D Digital Logic =rard. (Refer to Figure 8.) Centers the picture on the TV horizonta ly.

Color Adjustments - The three adjustments on the color adjust p. c. module ccz:rol the color intensity of the red, blue, and green guns of the color television CP (Cathode Ray Tube). These adjustments are factory pre-set and should not n require adjustment. When Adjustment is necessary, adjust each control for color. cally

Game - TV Switch - The "Game-TV" Switch (See Figure 12) which is mounted cz. ¢t

side of the color television, when facing the unit, makes it possible to displs

standard TV programming in TV Position of the switch. This feature is helpfu! trouble-shooting the system. It also simplifies servicing, since the television may b¢ serviced as a standard receiver.

Power Supply Adjustments - The Power Supply Module has two adjusimes control and 20 vde control. These adjustments are factory’ be changed, since Game operation will be adversely affected. Refer to Servis Manual for further information.

Color Television - The color television used in "Pace Car Pro" is a Sylvania ?‘rdel CX4161W all solid state unit. Other than Contrast and Brightness (located at : h of set), adjustments to the TV in “Game Mode" are ineffective. In TV Mode, :-2 TV operates normally and all TV controls are operative.

Page 21

EG 1000-A Analog Logic Board No. 2 red clip lead

  • 10 ca. cat C32 100 05) / css C89 C3 C14

eS eB | ee a ass VR1 VR2 VR3 VR4 VR5 VR6 VR7 VR8

joystick amp center L-E-D indicator lamp adjustment board

Figure 10 Joystick Amplifier Adjustment

Page 22

logic chassis

reen_ xm color adjust

Figure 11

Page 23

GAME -TV switches(shown in game position)

Figure 12

Page 24

—— — — =

‘Sane pot Eta Bio a cv <3 AB | BER ce Wes

7 —W | 77 a I — a BL — + wa og lcs 7 male | Bee] ce mio

p26 wv ae ts = = SSIs my aida i 6 ~ fs is if

HF 4 pt . i. i | rRACK BLANKING

1 1a | Ba i i}

Page 25

10009 “TH ‘ZOVTUA 40ND 13 7 i ‘ON! SaINOLVUORYT HOUVESIY TYSUTAINA he 900%0S $402 133HS GOOd!-93

Page 26

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 27

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 28

3ats IN3NOdWO

i)

494 03L9373S O2Y fev} (weneg (roves (ozres [Bare [oowe? [vove?

[eave¢ oO eee

[wow (Wore, (eevee [Sone [Wore [aove? [oons? [ered [oere? [Saved [ood [oore? [oove}

= 229. Gie> | flea? [eames feeve? [oore? [oew} [coved [ove? [oove? [Zore? [oaer} [von} [vond wri [ese SS

<> cit EIS) i Som BS Salt (vsive? [vore? [ozvd} [eoved [zoves [one? [ozee? [oor [ore are} — [oore} [east oe

By cx oun 6934 wool aus us [ (aaeze [roree [ace] [eoree [owe (ee? [eeezg [oree} [vore?} fo Comm ol (oon? = [aeve}

wes pita) iin) [poreg feeee? [Barre fore fore? (ee [ist] fieg Geog [Rowse [eared

eu 360 rey Cava (aeze [orre} [oeee? [aod [cera (Carec3 (oem? oor} Gorey Come} Gomes “Tes Cand (lozee} Lowes Lone.

[saree

AS ee lH (eed (ose? [oenag Coen?

[oore 9 (vow (Lorees

i 2 Wo

[ose 2

20m q [eeweg [esie? [Tome [seme

[song uF E 20009 “THI "ZOWTHA ZAOWD >a ‘OMI SaIMOLYHORYT HOMVASIY TWSUIAINN

an VET sanneee ae me 600v0S G 3406 133HS dO00I-93 G-O

s-d

Page 29

EG-IOOOA SHEET | OF 5 wear E conn IZ

Ue <c ELK GROVE VILLAGE, ILL. 60007

SELECTED

NOISE

PACE CAR

MASTER SOUND

SHUT OFF

$row It CI73 250 25V GND

I 56 C149 al42 C143

dak laf

Page 30

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 31

ev EG-IOOOA SHEET 3 OF 5 504011 wae ae mong ge

UB UNIVERSAL RESEARCH LABORATORIES INC,

Cc ELK GROVE VILLAGE, ILL. 60007

+ ov LE Ee race can icar pt TT 1SV 125,

TURN 5 C145 a im er 2K5% 33K 5%

a8 LAP NORMAL RUN FOR CARS © 14 SEC.

SET LAP FOR PACE

CAR AT 18 SEC.

Bae

xe Bx ae on sx H & es wvo | els > can ros serees

Page 32

Lie Snensat neseanci vazona etx GROVE VILLAGE, ILL. £0007

Rao cia [rae tos: Fs =ryre R126 cay CORB H. CAR BV.

vw

Page 33

AS EG-IOOOA SHEET 5 OF 5 50401! | [Je NNER Reseancn uasonaronses we.

1 ELK GROVE VILLAGE, ILL. 60007

RELEASED FOR PRODUCTION, 2-10-74 27

CARB RI ‘SOUND

Page 34

+ 5v0ee wean WOME +13 voc as Ue UNIVERSAL RESEARCH a al we.

ELK GROVE VILLAGE, ILL. 09007

ALL RESISTORS ARE 1/2 WATT, #10% UNLESS OTHERWISE NOTED.

2.ALL CAPACITORS ARE IN MICRO-FARAD

UNLESS OTHERWISE NOTED.

+ 20VDC<t -6 voc £—___ “ ST HE PaRrs Wor usta ov Ata ASSEMBLIES

Page 35

RED SIGNAL

CA-| BOARD 504022

[exe Wane ee

Ue UNIVERSAL RESEARCH LABORATORIES INC,

c ELK GROVE VILLAGE, ILL. 60007

CRASH xe)

BLUE SIGNAL

GRN SIGNAL

RE 2N5355 5.6K RO ‘2N5355 @ RED OUT com BLUE OUT

2N3394 10/35V. 10K ca it

Qe Ri2 JOO¢F

_2N3394 i0/35V. 10K

4423. 1F 2206 oO GREEN OUT NOTES: 1. ALL RESISTORS IN OHMS AND 1/2

WATT. 2,ALL CAPACITORS af, UNLESS. OTHERWISE INDICATED.

Page 36

1 Fe. 1 | [LEST