CATHODE RAY TOMES

Battlezone Caberat TM-166 1st Printing

Battlezone (rev 2) (Atari, 1980) · Technical Manual · 60 pages · 38 sections · original scan

Page 1
Scan of page 1

This page is a drawing, shown as the original scan.

Page 2

GAME SERIAL NUMBER LOCATION Your game's serial number is stamped on a plate on the outside of the game. The same number is also stamped on the chassis of the TV monitor, Regulator/Audio Il PCB, Battlezone Analog Vector-Generator PCB, and Battlezone Auxiliary PCB. Please mention this number whenever calling your distributor for service.

GAME SERIAL # IDENTIFICATION TAG

TV MONITOR

BATTLEZONE AUXILIARY PCB

REGULATOR/AUDIO Ii PCB.

BATTLEZONE ANALOG VECTOR-GENERATOR PCB

Page 3

Fics .

  • )60hlUgl . ™ os — ~

Operation, Maintenance and Service Manual

Complete with Illustrated Parts Lists

Published by: ATARI INC. 1265 Borregas Avenue P.O. Box 427 Sunnyvale, California 94086

Copyright © 1980 by Atari, Inc. All rights reserved.

No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private

use, without permission from the publisher. AT A R " Lithographed in the U.S.A. 11d fw Warner Communications Company

Page 4

Table of Contents

Location Setup A. B. Cc. New Parts... 6. eee cee e nett eter en eens 1 Game Inspection 3 Game Installation. . 3

  • Line Voltage Selection 3
  • Interlock and Power On/Off Switches ...............eeseeeeeee 4 Self-Test Procedure ......-.-.-..- -. 7 Option Switch Settings . 8
  • Bonus Play Feature. . 8
  • Coin Mechanism Multipliers 8
  • Examples of Option Switch Settings Game Play .............00.
  • Attract Mode 20... cece cee ence eee e teens
  • Ready-to-Play Mode ....... 0... 0c eee cee eee eee eee
  • PlayMode ..........
  • High Score Initial Mode

Maintenance and Repair A. B. c. Cleaning .... 2.6... cece ee eee cece eee e eee eee 16 Fuse Replacement...........-.-..0- ces eeeee eee -. 16 Opening the Control Panel .... 16

  • LED Start Switch Replacement .... -. 16
  • Control Handle Maintenance and Repair..................20005 18 TV Monitor Removal Printed-Circuit Board Replacement - 20
  • Analog Vector-Generator and Auxiliary PCB Removal .. 20
  • Regulator/Audio II PCB Removal ............ 0... cece eee eee 20 Fluorescent Tube Replacement ............ 0.00 cece eee eee eee 21 Game Operation... 0.0.0... eens 22

\Ilustrated Parts Lists

Page 5

List of Illustrations

Figure 1 Overview Of Game ... 6. cee eee eee teen eee e eee eees 2 Figure 2 Installation Requirements baa oe 3 Figure 3 Line Voltage Selection ....... 4 Figure 4 Interlock and Power On/Off Switches 5

Figure 5 Location of Self-Test Switch, Volume Control and Option Switches... 6 Figure 6 Self-Test Procedure 7 Figure 7 Game Option Settings 9 Figure 8 Game Price Settings. . . 10

Figure 9 Coin Counter Option Settings Figure 10 Opening the Control Panel Figure 11 Control Handle Maintenance and Repair ...... a sees Figure 12 TV Monitor Removal..........-0. 0c ccc cece eee eee eee e eee 19

Figure 13 Printed-Circuit Board Replacement Figure 14 Fluorescent Tube Replacement Figure 15 Power Distribution Figure 16 Signal Distribution

Illustrated Parts Lists: Figure 17 Cabinet-Mounted Assemblies ........ Figure 18 Control Panel Assembly... . : Figure 19 Control Handle Assembly Figure 20 Fluorescent Light

Figure 21. Power Supply Assembly for X-Y Games . . Figure 22 Battlezone™ AuxiliaryPCB ............ Figure 23 Battlezone™ Analog Vector-Generator PCB . Figure 24 Regulator/Audio || PCB Assembly . Figure 25 Coin Door

Page 6
NOTE

If reading through this manual does not lead to solving a certain maintenance problem, call Tele-Help™ at the Atari Customer Service office in your geographical area, as shown in one of the two maps below. Order all parts from the California office.

WEST and CENTRAL U.S.A.

Parts for all Atari Customers. Sales and Service

Atari Coin-Op Customer Service 1344 Bordeaux Drive, Sunnyvale, CA 94086 Telex 17-1103

(Monday - Friday, 7:30 - 4:00 pm Pacific Time)

s From California, Alaska or Hawaii (408) 745-2900

a» From anywhere else in this area toll-free (800) 538-1611

EAST U.S.A.

Sales and Service Only

Atari Inc. New Jersey Customer Service Office Cottontail Lane, Somerset, NJ 08873 Telex 37-9347

(Monday - Friday, 7:30 - 4:00 pm Eastern time)

From New Jersey (201) 469-5993

From anywhere else in this area toll-free (800) 526-3849 s

Page 7

Battlezone ™/Cabaret

Notice Regarding Non-Atari Parts

WARNING

Use of non-Atari parts or modifications of your Atari game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

Atari, Inc.’s warranty (printed on the inside back cover of this manual) may be voided, if you do any of the following:

1.) you substitute non-Atari parts in your coin-operated game, or

2.) you modify or alter any circuits in your Atari game by using kits or parts not supplied by Atari.

Not only may the use of any non-Atari parts void your warranty, but any such alteration may also adversely affect the safety of your game, and may cause injury to you and your players.

Page 8

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 9
WARNING-SHOCK HAZARD This game is designed to be connected only to a grounded 3-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electric shock if this game is not properly grounded!

A. New Parts

The Battlezone™/Cabaret game has four new parts. If you have worked on Atari games in the past, then you should be aware of these important differences. The new parts are: Control Handle. This new control is a redesign of the Atari gear shifter. It has been strengthened by adding several additional ribs to the interior and exterior of the housing. These ribs keep the assembly properly aligned to assure proper switch contact. Another new feature is the rubber centering bellows; it acts as a centering spring to return the control handle to the center position. The microswitches are now mounted with locknuts for easy replacement.

Page 10

TV MONITOR SHIELD

e

CONTROL HANDLE

START SWITCH xv MONITOR CONTROL r, PANEL

ACCESS

ATTRACTION, PANEL

PANEL a sn f | AUXILIARY PCB

i\iy ANALOG VECTOR. | GENERATOR PCB COIN DOOR REGULATOR! ? AUDIO II PCB

SPEAKER

POWER SUPPLY

POWER ONIOFF Hp SWITCH

Figure 1 Overview of Game

Page 11

@ Atari's X-Y game circuitry has expanded into two interconnected printed-circuit boards—the Analog Vector-Generator and the Auxiliary PCBs. The circuitry produces more lines on the screen at a faster rate, thus creating a smoother screen image. @ This game includes a newly designed power supply assembly. This power supply has a larger transformer to handle the increased power requirements of the expanded game circuitry. @ Cabaret™ Cabinet Design. This more compact cabinet was designed to occupy less than 4 square feet of floor space.

These new parts, as well as ail other major parts in the game, are illustrated in Figure 1. Throughout this manual, wherever one of these new parts is

mentioned, you will see this symbol: m5)

B. Game Inspection

This new game is ready to play upon removal from the shipping carton. However, your careful inspection is needed to supply the final touch of quality control. Please follow these steps to help us insure that your new game was delivered to you in good condition.

NOTE Do not plug the game in yet!
  • Examine the exterior of the game cabinet for dents, chips, or broken parts.
  • Unlock and open the access panel of the cabinet and inspect the interior of the game as follows: @ Check that all plug-in connectors (on the game harness) are firmly seated. Replug any connectors found unplugged. DON’T FORCE CONNECTORS TOGETHER. The

oo” Own Dm connectors are keyed so they only go on in the proper orientation. A reversed edge connector will damage a PCB and will void your warranty. @ Check that all plug-in integrated circuits on the game PCB are firmly seated in their sockets.

WARNING To avoid possible unpleasant electrical shock, do not touch internal parts of the TV monitor with your hands or metal objects held in your hands!

@ Note the location of the game’s serial number—it is printed on the special label on the outside of the game cabinet. Verify that the serial numbers also stamped on the Battlezone™ Analog Vector-Generator PCB, Auxiliary PCB, Regulator/Audio II PCB and TV Monitor are all identical. A drawing of the serial number locations is on the inside front cover of this manual. Please mention this number whenever you call your distributor for service. @ Check all major subassemblies such as the power supply, control panel and TV monitor for secure mounting.

C. Game Installation

Figure 2 Installation Requirements

Power 150 watts Temperature 0 to 38°C (32 to 100°F) Humidity Not over 95% relative Space Required 52 x 6024 cm (20%2 x 23 7/8 in.) Game Height 139 cm (54% in.)

  • Line Voltage Selection Before plugging in your game, make sure that the voltage selection plug on the power supply (see Figure 3) is correct for your location’s line voltage. Check the wire color on the plug and see if it is correct per the list below.

Line Voltage Range Voltage Selection Plug Color 90-110 VAG (100) —_—-Violet 105-135 VAG (120) Yellow 200-240 VAC (220) Blue 220-260 VAC (240) Brown

Page 12

Figure 3 Line Voltage Selection

  • Interlock and Power On/Off Switches @ Ifthe results of the preceding step are satisfacate . . tory, the interlock switches are operating pro- To minimize the hazard of electrical shock while perly. if the TV monitor doesn’t go off as working on the inside of the game cabinet, two inter- described, check to see if the corresponding inlock switches have been installed (see Figure 4). terlock switch is broken from its mounting or One is located behind the access panel and one is stuck in the “on” position. behind the coin door. These switches remove all AC line power from the game circuitry when a door is opened.

Check for proper operation of the interlock switches by performing the following steps: @ Unlock and open the access panel and the coin door. @ Plug the AC line power cord into an AC outlet. @ Close the access panel and coin door. @ Set the power on/off switch to the on position. Within 30 seconds the TV monitor should display a picture. @ Slowly open the access panel. The TV monitor picture should disappear when the panel is opened approximately 2.5 cm (1 inch). Close and lock the access panel and repeat this step with the coin door.

Page 13

SWITCH

SAFETY INTERLOCK SWITCH

POWER ON/OFF SWITCH

Figure 4 Interlock and Power On/Off Switches

Page 14

BATTLEZONE ANALOG VECTOR-GENERATOR PCB

OPERATOR OPTION SWITCH

VOLUME INCREASE: TURN CLOCKWISE

SELF-TEST VOLUME CONTROL SWITCH (EUROPEAN GAMES)

Figure 5 Location of Self-Test Switch,

Volume Control and Option Switches

Page 15

D. Self-Test Procedure

Part of the self-test procedure includes a display of the operator-selectable gare options. Therefore, we suggest you run the self-test pro- This game will test itself and provide data to cedure anytime you need to change the game’s demonsirate that the game’s circuitry and con- options. trols are operating properly. The data is provided on the TV monitor and the game speaker, no addi- To run the self-test, follow the instructions outtional equipment is necessary. lined in Figure 6.

Figure 6 Self-Test Procedure

Results if Test Fails Results if

Instruction Test Passes

  • Set selftest After about 3 switch to on posi- seconds, the TV tion (see Figure 5). monitor displays the picture below.

CENTER COIN MECH MULTIPLIER (LEFT MECH OF A 2-MECH DOOR)

RIGHT COIN MECH MULTIPLIER

SWITCH SWITCH TOGGLE 1 TOGGLE 8

oN \ MG 7X Ls NTCDA ”

<

SWITCH SWITCH AT P10 AT M10 (TOP ONE) (BOTTOM ONE)

DISPLAY OF COMPLETE CHARACTER SET RAM FAILURE is indicated by a sequence of 1 to 10 tones. You will hear a short low tone for each good RAM chip, and a long high tone for a tailing RAM chip. The test stops with the first failing RAM-chip pair (example: J2 and H2 are a pair). To restart the sequence, press the reset pushbutton on the Battlezone™ Analog Vector-Generator PCB, or set the self-test switch to off, then again to the on position. Identify the bad RAM chip with the table below. Example: four short low tones followed by a long high tone, then one more snort low tone indicates failure of RAM at location B2, Long High Tone Bad RAM Chip Location ‘tst J 2nd H2

3rd A2 4th Al

Sth B2 6th B1 7th c2 8th fea] 9th D2 oth D1

ROM/PROM FAILURE is indicated by two columns of numbers on the left side of the screen. The number in the left column indicates the location of the failing ROM/PROM(). Identify the bad ROM/PROM with the table immediately below. Ignore the hexadecimal numbers in the right column.

Displayed No. Failing ROM Failing PROM BIC3* BIC3*, E3 AS A3, FIH3 et FIH1 v1 Kt uM1 Ni** *It ROM or PROM BIC3 is bad, you will hear a continuous low tone, and the program may be unable to display a screen image. **If ROM N1 is bad, program will be unable to produce tones in RAM test.

[Selt-test continued on next page] NOMRYNA0

Page 16

Figure 6 Self-Test Procedure, continued

Results it

Instruction Test Passes

Results if Test Fails

MATH BOX FAILURE is indicated by a single letter displayed in the upper right corner of the display. Math-box failure is explained in the Signature Analysis Procedure, on the game schematic Sheet 1, Side B. Identify the failure with the table below.

Displayed Letter Failure T Time out error H Data error—high byte L Data error—low byte

  • Activate slam ‘switch, all control As switch activates, you'll hear a low beep. panel switches and As switch deactivates, coin door switches. you'll hear a high When satisfied with beep. test, set self-test ‘switch to off position.
  • Sounds Test (Optional) You may test the hardware-generated sounds by starting a game and proceeding as follows: Engine Rumble (Idle): Should be heard as soon as start button is pushed. Engine Rumble (Active): Pushing both control handles forward should cause an increase in pitch. Releasing control handles You will not hear a low or high beep for the defective switch.

should cause engine rumble to return to idle. Loud Shot: Press the fire button.

Loud Explosion: Heard when you get hit, indicated by cracked windshield. Soft Explosion: is heard when you hit an enemy tank or another object.

E. Option Switch Settings

  • Bonus Play Feature Battlezone™/Cabaret offers a bonus play for certain combinations of coins inserted. This bonus feature is operator-selectable, meaning you may choose to offer it or not.

For example, with your game set at 50¢ per play, players who deposit four successive quarters or a $1.00 coin, then press the start button, can receive a bonus play. Therefore, players can receive 3 plays for $1.00. This bonus feature encourages players to insert more money than just the minimum 50¢ required for one game. Various other bonuses are also available (see Figure 8).

  • Coin Mechanism Multipliers Since early in 1980, Atari has made available its new coin door which has either two or three mechanisms. All recent Atari game PCBs identify the different mechanisms in a Certain pattern.
Page 17

The right coin mechs are all the same to the , game's logic, regardless of whether you have two or three mechs in your door. In addition, the logic sees the left mech in a 2-mech door and the center mech in a3-mech door as the same. Refer to the diagram below.

ese] jst fase) [[2se |jst

This pattern is important for you to know, so you can correctly set the “multipliers” for each mech. The multipliers determine how much each mechanism will be worth to the game’s logic. The basic unit of measurement is 25¢, which equals a multiplier of x 1. Therefore, if you have a 25¢/25¢/$1 coin door, you will probably want to set the center and right option-switch multipliers at x 11x 4. (The left mech in a 3-mech door always has a value of x 1—you cannot change its value.)

You Can set these multipliers with toggles 3 thru 5 on the Battlezone PCB switch assembly at location P10. For exact settings of these toggles, refer to Figure 8.

  • Examples of Option Switch

Settings

To explain the options, we have provided in Figure 8 fourteen examples of the most common U.S. situations. The toggles mentioned are all in the switch at location P10; they only relate to game price, coin mechanism multipliers, and bonus play. You should set the toggles relating to other functions as you see fit, although Figure 7 provides “$” symbols indicating Atari’s recommendations.

Figure 7 Game Option Settings

RD To change toggle positions on the switch assemblies, you need

not remove the game PCB. The switches, usually colored blue, are easily accessible when the Battlezone Analog Vector-Generator PGB is mounted in place. When changing the options, verify proper results on the TV monitor display by performing the self-test. Note that changing an ‘option on any of the following eight toggles will cause an immediate change on the TV monitor screen during the self-test.

Toggle Settings of 8-Toggle Switch on Battlezone PCB (at M10) (BOTTOM switch when PCB is in game) 8 7 6 5 4 3 2 4 Option

On On Off Off

On On On Off

Off On Off Off

On On

On Off

On Game starts with 2 tanks Off Game starts with 3 tanks $ On Game staris with 4 tanks Off Game starts with 5 tanks

Missile appears after 5,000 points Missile appears after 10,000 points $ Missile appears after 20,000 points: Missile appears after 30,000 points No bonus tank Bonus tank at 15,000 and 100,000 points $ Bonus tank at 25,000 and 100,000 points Bonus tank at 50,000 and 100,000 points English language $ French language German language Spanish language

Page 18

Figure 8 Game Price Settings §

The white block below contains the manufac- P10, on the Battlezone™ Analog Vector-Generator turer’s suggested settings. All numbers 1 thru 8 are PCB (the TOP switch assembly). toggle settings on the 8-toggle switch at location

50¢ PER PLAY:

Bonus No bonus $1.00 = 3 plays z ; | 7 6 5 Straight Off Off On 25¢ Door :

Off

250/$1.00 Door or 25¢/25%/$1.00

25¢ PER PLAY:

Bonus No bonus $.50 = 3 plays

Straight 25¢ Door

25¢/$1.00 Door or 25¢/250/$1.00 Door

Circled numbers refer to coin-door labels you should use with each situation (labels are illustrated on opposite page).

Page 19

Figure 8 Game Price Settings, continued For your information, we have defined below the switch settings for those options relating to game price, coin mechanism multipliers, and bonus play. This information is useful in case you need to temporarily set the Battlezone™ game on free play, or if you have German coin mechanisms in your door.

Toggle Settings of 8-Toggle Switch on Battlezone PCB (at P10). TOP switch when PCB is in game

87654321Option
OnOnFree play
OnOff1 coin* for 2 plays
OffOn1 coin* for1 play
OffOff2coins* fort play$
OnOnRight coinmech x 1$
OnOftRight coin mech x 4
OffOnRight coin mech x 5
OffOffRight coin mech x 6

On Center coin mech x 1 $ (Both these settings affect Off Center coin mech x 2 the left mech in a 2-mech door)

OnOnOnNo bonus coins
OnOnOff

On Off On

OnOffOff
OffOnOn

For every 2 coins™ inserted, game logic adds 1 more coin* For every 4 coins” inserted, game logic adds 1 more coin* For every 4 coins” inserted, game logic adds 2 more coins” $ For every 5 coins” inserted, game logic adds 1 more coin*

“In the U.S, a “coin” is defined as 25¢. In Germany a “coin” is 1DM.

$ Manufacturer's suggested settings To achieve bonus plays, all coins must be inserted before pushing start button.

ATARI oe JS @@ 2 coins =1 play

We? @ 1 coin ATARI

je @ @ 2 coins = 1 play ATARI 8000 4 coins = 3 plays ne @@ 2coins = AT Q@® 3 coins @@@@ 4 coins

° @ @ 2 coins = 1 play

iS $1 coin =3 plays

(Susan B. Anthony coin)

@ 1coin = 1 play Are’ 2 play minimum (2 coins = 2 plays)

Note: Battlezone cannot be set for a 2-coin minimum. Therefore, do not stick the above label no. 6 on the Battlezone coin door.

J (Write in the

appropriate phrase)

W

Page 20

Figure 9 Coin Counter Option Settings

[These toggles determine which coin mechanisms activate which counters}

Toggle Settings of 4-Toggle Switch on Game PCB (at L11) 4 3 2 1 For Games Having These Coin Doors: Option

|OnOn| Thai 1 Baht/t Baht, German 1 DM/1 DM, U.S. 25¢/-Al 3 coin mechanisms are

25¢, Belgian or French 5 Fri5 Fr, Swiss or French same denomination; all 1 Fri Fr, U.S, 25¢/25¢/25¢, Japanese Y100/Y100, register on one coin Swedish 1 Kr/1 Kr, U.K. 10 P/10 P, Australian 20¢/- counter. 20¢, or Italian 100 L/100 L.

OffOnGerman 2 DM/1 DM, German 1 DM/5 DM, U.S. 25¢)-Left and center mechanisms

254/$1, or U.S. 25¢/81. are same denomination; right mech is another denomination. Requires two coin counters.

OnOffNo coin door is currently designed for this contig-Left mech is one denomina-

uration, tion; center and right mech are another denomination. Requires two coin counters.

OffOffGerman 1 DM/2 DM/5 DM.Left, center and right mechs

are 3 different denominations. Requires three coin counters.

F. Game Play

Atari’s Battlezone™ is a one-player game with an X-Y or vector-generation monitor. The game depicts a first-person view from inside a tank. The battles are fought in a large valley that is completely surrounded by mountains and volcanos. The valley floor contains pyramids and boxes that can provide temporary protection for players. (These cannot be destroyed by shots.)

The enemy consists of slow and fast “super” tanks and intelligent missiies—ail of which become more evasive as the game progresses. In addition, flying saucers appear periodically. These don’t shoot at players, but players can get very high point scores for shooting them.

The Battlezone game has five possible modes of operation: Attract, Ready-to-Play, Play, High Score Initial, and Self-Test. Self-test is a special mode for checking the game switches and computer functions. You may enter this mode at any time. When entered, all game credits are cancelled and the high score initials are reset.

  • Attract Mode The attract mode begins when power is applied to the game, after a play or high score initial mode, or after self-test. This mode is continuous and is only interrupted when a game is paid for and accepted or when in self-test.

In this mode, the TV monitor displays three possible pictures. One is a simulation of a typical game, another is the high score table, and the third picture shows the Battlezone logo rolling up from the bottom of the screen.

  • Ready-to-Play Mode This mode begins when sufficient coins have been accepted for a game. It ends when the start pushbutton is pressed. When this mode begins, the message PUSH START flashes in the center of the
Page 21

screen, and the start button will also flash on and off. The sequence of displayed pictures are otherwise the same as those shown in the attract mode.

  • Play Mode The play mode begins when the start pushbutton is pressed. The start LED will then stay on, and the audio will begin. The mode ends when the player's last tank of the game is lost.

The game starts with the siow tank visible on the screen. The player can determine the position of either type of tank or the missile by reading the messages in the upper left corner of the screen. For example, ENEMY TO RIGHT may be displayed. In addition, the sweeping radar display shows a dot for the enemy’s location, accompanied by a sonar “blip” sound.

The upper pie-shaped area on the radar represents the player's range of view on the screen below. If the enemy falls anywhere within the radar circle, it will be accompanied by the message ENEMY IN RANGE.

Occasionally the flying saucer appears on the screen. It is a observer to the battle and will not destroy the enemy or player. Its position is never shown on the radar, but players can earn 5,000 points for shooting it down. The saucer does act as a distraction, though, since it usually appears at the same time as the enemy tanks or missile. Saucers can be shot by the player as well as enemy tanks. Scoring for hitting the enemy is as follows: the slow tank earns a player 1,000 points; the missile earns 2,000 points; and the super tank earns 3,000 points. A super tank moves and turns twice as fast as both the slow tank and the player's tank.

Several options allow operators to set the Battlezone™ game for 2 through 5 tanks, for giving a bonus tank after earning various point scores, and for adjusting difficulty by having the missile appear for the first time at various point scores. For information on how to set your game for these options, refer to Figure 7 in this manual.

  • High Score Initial Mode If a player's score exceeds the minimum on the high score initial list, he or she may put up to three initials on this list at the end of the game. The instructions are self-explanatory and are provided in four languages.
Note that this list is erased whenever you enter the self-test, press the RESET button on the Battlezone™ Analog Vector-Generator PCB, or turn off the power. This resetting will put a list of ten “highest” scores and initials on the screen (to provide player challenge).

Any score on the list over 100,000 points is specially highlighted with a tank symbol following the player's initials. If a player doesn’t enter his or her initials within about 60 seconds, the game will automatically enter dashes instead. After this, the game reverts to the attract mode. aS

Page 22

All games require certain maintenance to keep them in good working order. Clean, properly maintained games will attract players and earn more profits.

The most important maintenance item is running the self-test every time you collect money from the cash box. Just looking at a game will not tell you if the control handle switches, fire button, or start switch is broken, or if the LED has burned out. The self-test will inform you of any of these possible problems.

Second, you should regularly clean the outside of the game and the coin mechanisms. In addition, you will need to regularly lubricate the control handle: for details see this chapter.

Battlezone Cabaret

Page 23

A. Cleaning

The exterior of the game cabinet and the metal and acrylic surfaces may be cleaned with any nonabrasive household cleaner. If desired, special coin machine cleaners that leave no residue can be obtained from your distributor, Do not dry-wipe any of the acrylic panels, because any dust can scratch the surface and result in fogging the plastic.

B. Fuse Replacement

This game contains five fuses—all on the power supply assembly (not including the TV monitor fuses). Note that the F2 holder is unused. Replace fuses only with the same type as listed in Figure 21 of this manual. See the Quadrascan TV monitor manual, TM-151, for the monitor fuse data.

C. Opening the Control Panel

Prior to repairing or replacing any switch on the control panel, unplug the game. Then open the coin door.

Reach through the opening and remove all three sets of carriage bolts, hex nuts, split lock washers, and flat washers, located on the underside of the control panel (see Figure 10). Lift up on the control panel and tilt it towards you.

  • LED Start Switch Replacement The light-emitting diode (LED) switch on the control panel has a very low failure rate. In case the switch should ever be suspect, first test it per the description that follows. To replace the switch, refer to Figure 10.

To remove LED switch: @ Remove all wires from the faulty switch. @ Turn the switch counterclockwise (as viewed from inside of control panel) while holding the black cone-shaped nut on the outside of the control panel. @ Install a new switch using the reverse procedure. @ Reconnect the harness wires.

NORMALLY CLOSED / (NC) CONTACT fo NORMALLY OPEN ys ~~ (N.0) CONTACT yi \\ LIGHT-EMITTING-DIODE COMMON IED) CONT COMMON (LED) CONTACTS

eT 2

Figure 10 Opening the Control Panel

Page 24
NOTE: Do not remove the flat actuator spring unless you have a replacement. Removing the spring will bend it, and it will no Jonger be usable.

o_ PIN LUBRICATE HERE

Figure 11 Control Handle Maintenance and Repair

Page 25

@ Remove the wires from the suspected switch. @ Set multimeter to ohms scale. Set ohms scale to Rx 1, then zero the meter. @ Connect multimeter leads to appropriate LED switch contacts (see Figure 10 for designation of switch contacts and meter lead placement). @ Check contacts (push and release the switch button) for closed and open continuity. @ Ifthe contacts do not operate sharply or always remain closed or open, then replace the LED switch as outlined in the figure.

  • Control Handle Maintenance and Repair Normal maintenance involves lubricating three parts in the control handle approximately every six months (this requires removing the controls). First open the control panel as described in Figure 10. Then unplug the “quick-disconnect” connectors on the four control switches, as well as the three connectors for the fire switch.

From the inside of the control panel, remove the four flat and lock washers and four screws that mount the control onto the wood support and the round bezel.

Then open up the control handle assembly by removing the slx split lock washers and screws (see Figure 11). In addition, remove the two switches and carefully save the small actuator pins.

For lubrication, use only Dow Corning #111 heavy silicone lubricant (Atari part no. 78-1710). Lubricate the following two parts inside the control: @ The spherical part of the shaft and the two small pivot pins that protrude from this area, and @ The two clear plastic actuator pins, located over the switches (push the narrow ends of the pins into the tube to cover them with lubricant).

NOTE Do not remove this spring unless you have a replacement on hand! Removing the spring will bend it, and it will no longer be usable.

GREEN

YELLOW YELLOW

BLACK BLACK

Et ORANGE WHITE YELLOW GREEN

Repairs on the control handle would probably only involve replacement of switches. When removing a switch, be careful not to lose the small clear plastic actuator pins that sit above the white switch actuators. Note: the flat head of the pin must always face towards the switch actuator.

Page 26

D. TV Monitor Removal

WARNING High voltages may exist in any television monitor, even with power disconnected. Use extreme caution and do not touch electrical parts of the TV yoke area with your hands or with metal objects in your hands! If you drop the TV monitor and it breaks, it will implode! Shattered glass and the yoke can fly 6 feet or more from the implosion. Use care when replacing any TV monitor.

If you should need to remove the Quadrascan X-Y TV monitor, follow steps 1 thru 6 as listed on this page. Refer to Figure 12. First be sure the game is unplugged from its wall outlet!

  • Unlock and open the rear access panel. Remove the three Allen screws and internal-tooth lock

Disassemble in the order indicated, (Circled numbers match the steps above.) washers that secure the monitor-shield retainer strip at the top of the game. Carefully remove the cardboard graphics bezel by prying loose the staples. Unplug the 12-pin harness connector behind the TV monitor. Remove the four sets of carriage bolts, flat and split lock washers, and hex nuts that hold down the TV chassis. Carefully slide the TV monitor chassis out the front of the game. If you must replace the TV monitor with a new one, place the red and green overlays on the face of the new picture tube as follows. Place the red overlay within the top 2% inches of the screen; then butt up the green overlay to the red one. Once the monitor has been installed in the cabinet, check for proper alignment with the graphics bezel as follows—before stapling it into place. The vertical center line of the gunsight should be directly under the D in RADAR (at the top center of the bezel). In addition, the radar circle should be centered in the die-cut circle of the cardboard.

Figure 12 TV Monitor Removal

Page 27

E. Printed-Circuit Board Replacement

You may wish to remove the Battlezone™ Analog Vector-Generator printed-circuit board (PCB), Auxiliary PCB, or the Regulator/Audio |I PCB for service or inspection. To do this, refer to Figure 13 and proceed as follows:

1. Analog Vector-Generator and

Auxiliary PCB Removal

Unlock and open the access panel. Unplug the 24-pin PCB interconnector from the Auxiliary PCB or the Analog Vector-Generator PCB (whichever board you are removing). Remove the 44-pin edge connector from the right side of the PCB. Locate the Phillips-head screw that extends through the PCB and into the wood block (at the right side of the board). Remove this screw, as well as the two fiber washers.

REGULATOR/ AUDIO II PCB Remove the PCB from the cabinet by pulling it out of the plastic PCB retainer. Reinstall the PCB, making sure that the 44-pin edge connector is properly plugged in. Note that the connector is keyed to fit on only one way, so if it doesn’t slip on easily, don’t force it! A reversed connector will probably damage your game and will void the warranty. Check that the operation of the game is correct by performing the self-test. This is especially

important with any game when you replace a PCB.

Regulator/Audio II PCB Removal Unlock and open the access panel. Remove the five plug-in connectors on the Regulator/Audio || PCB. Note that all of these connectors are keyed for proper orientation. Locate the two Phillips-head screws that extend through the PCB and into the wood behind the PCB. Remove and save these two screws and the four fiber washers. Remove the PCB from the interior wall of the cabinet.

BATTLEZONE AS AUXILIARY PCB

y. BATTLEZONE ANALOG VECTOR- GENERATOR PCB

Figure 13 Printed-Circuit Board Replacement

Page 28

To replace the white fluorescent tube behind the F. . Fluorescent Tube front graphics attraction panel, follow this proce. dure (see Figure 14).

F. . Fluorescent Tube front graphics attraction panel, follow this proce Replacement

  • Open the coin door. Remove the two Y-shaped
WARNING connectors from the ends of the fluorescent . tube. Now carefully remove the tube from its \f you drop a fluorescent tube and it breaks, it will implode! Shattered glass clamps by pulling it towards you. can fly 6 feet or more from the implosion. 2. Replace with a new tube. Do not snap the tube Use care when replacing any fluorescent in vigorously—you may break it, causing an imtube. plosion!
  • Close the coin door and lock it.

Figure 14 Fluorescent Tube Replacement

Page 29

G. Game Operation

With this manual you received three large sheets that contain the wiring and schematic diagrams for your game. Sheet 1, Side A, includes information that shows the arrangement of these diagrams.

Battlezone™ is a microprocessor-controlled game. The microprocessor is contained on the Analog Vector-Generator PCB. This board receives switch inputs from the control panel and coin door. These inputs are then processed by the Analog Vector-Generator PCB and output to the TV monitor, Regulator/Audio It PCB, and control panel.

The TV monitor is an X-Y monitor. Therefore, the monitor receives signals for the X, Y and Z axes. Since the location of the beam in the monitor is totally controlied by the X- and Y-axis outputs of the Analog Vector-Generator PCB, this board does not contain a standard sync circuit. The X- and Y-axis inputs to the monitor step in increments of 1024 steps for the X (horizontal) axis, and 768 steps for the Y (vertical) axis. The Z axis merely controls the intensity of the beam. ad The Regulator/Audio I] PCB performs two functions: 1) it regulates the voltages from the power supply to +5 VDC and + 12 VDC, and 2) it amplifies the audio output from the Auxiliary PCB.

Specifically, the +5 VDC from the Regulator/- Audio I! PCB provides most logic power to the Analog Vector-Generator and Auxiliary PCB; +22 VDC is regulated on the Analog Vector-Generator PCB to produce +15 and +5 VDC (the latter for the digital-to-analog converters); and + 22 VDC provides power for the audio output of the Auxiliary PCB. The audio output from the Regulator/Audio II PCB directly drives the game speakers and is controlled by the volume control, mounted inside the coin door.

The Power Supply is the source of all voltages in the game. These voltages are protected by four fuses in the fuse block on the power supply chassis. The primary winding of the power supply transformer is protected by the cartridge-type fuse in the power supply chassis.

Figure 15 illustrates the distribution of power in this game. Figure 16 illustrates the distribution of signals.

Page 30

YS TV MONITOR

CONTROL PANEL

FLUORESCENT LAMP

AUXILIARY PCB

POWER INTERLOCK SWITCHES

ANALOG VECTOR: GENERATOR PCB

COIN DOOR

REGULATOR/AUDIO i PCB

AC POWER CORD

POWER SUPPLY

ON/OFF SWITCH

Figure 15 Power Distribution

Page 31

TV MONITOR

CONTROL PANEL

VOLUME CONTROL

\_A

&,C,R COIN COUNT

OS) (AY REGULATORIAUDIONI PCB S|

Figure 16 Signal Distribution ANALOG VECTOR. GENERATOR PCB

AUXILIARY PCB

GAME SPEAKER

Page 32

Hlustrated

Parts Lists

The purpose of this chapter is to provide you with the necessary information for ordering replacement parts for your Battlezone™/Cabaret game. Please

note that, for simplicity, common hardware has been deleted from most of these parts lists. This includes screws, nuts, washers, bolts, etc.

The parts lists have been arranged in alphanumeric order. For example, all “‘A-” prefix numbers come first. Following this are numbers in sequence evaluated up to the hyphen, namely 00- thru 99-, then 000598- thru approximately 110000-.

When ordering parts from your distributor, give the part number, part name, applicable figure number of this manual, and serial number of your game. This will help to avoid confusion and mistakes in your order. We hope the results will be less downtime and more profit from your game.

Battlezone ™/Cabaret

Page 33

Schematics, Self-Test Label & Manuals— see parts list on opposite page

036669-01 (Monitor Shield)

036676-01 (Graphics Bezel)

Control Handle Assy.— See Figure 19

Control Panel Assy. See Figure 18

036674-01 (Attract. Panel)

19-9032 (Vol. Control)

A021700-01, -02, -03 (Coin Box) 030249-01 (Separator)

036130-01 (Speaker Grille)

78-3201 (Cabinet Leg)

NOTICE TO ALL PERSONS RECEIVING THiS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA This drawing is only conditionally issued, and neither receipt nor possession thereof confers or transters any fight in, or license to use, the subject matter of the draw ing or any design or technical information shown thereon, nor any right to reproduce this drawing or any parl tereof. Except for manufacture by vendors of Atari Inc., and for _manufacture under the corporation's written license, no right to reproduce this drawing is granted or the subject matter thereof unless by written agreement with or written permission {rom the corporation,

Figure 17 036670-01 (Shield Retainer)

& y 036263-03, -04 (Monitor Overla

002728-01 (Ctrl-Pane! Brkt.)

0357.45.02 (184n. PCB Retai

Fluorescent Light— See i? 20 A036247-01 (PCB interconne Coin Door— See Figure 25

934536-02 (Thin Foam Damper)

036262-01 (Coin Box Brkt.) * 007882-02 (Interl. Sw. Cover)

A036189-01 (interl, Sw.)

148001-00 (Speaker)

See Figure 21

009992-01 (On/Off Sw. Cover)

A036651-xx ys)

92-045 (%&Y Monitor)

Auxiliary PCB— See Figure 22

035745-03 (10-In, PCB Retainer)

iner)

ctor)

)

Reg./Audio Il PCB— See Figure 24

Analog Vect.-Gener. PCB— See Figure 23

034536-03 7 (Thick Foam Damper)

Power Supply Assy.—

A034631.01 (On/Off Sw.) A034841-02, A034863-02, A035989-02 (Power Cord)

Cabinet-Mounted Assemblies

Page 34

re Battlezone ™/Cabaret

Figure 17 Cabinet-Mounted Assemblies Parts List

Part No. Description

A002465-01 Coin Counter A021700-01 Coin Box Assembly (for ail the same coins) A021700-02 Coin Box Assembly (for two different coin denominations—has one separator) A021700-03 Coin Box Assembly (for three different coin denominations—has two separators)

A034841-02Strain Relief Power Cord(U.S.)
A034863-02Strain Relief Power Cord(Germany and other countries)
A035989-02Strain Relief Power Cord(Australia)

A034631-01 On/Off Switch Assembly

A036189-01Interlock Switch Assembly(modified for safety)

A036247-01 Printed-Circuit-Board Interconnector

A036603-01Main Harness Assembly(also includes on/off switch, 2 interlock switches and their brackets,

and volume control and its bracket)

The following six items are the technical information supplements to this manual: DP-166-01 Battlezone™/Cabaret Schematic Drawings (Sheet 1) DP-166-02 Battlezone/Cabaret Schematic Drawings (Sheet 2) DP-166-03 Battlezone/Cabaret Schematic Drawings (Sheet 3) ST-166 Battlezone/Cabaret Label with Self-Test Procedure and Option Switch Settings TM-151 Instruction and Service Manual for G05-802/805 Quadrascan™ X-Y Monitor TM-166 Battlezone/Cabaret Operation, Maintenance and Service Manual 19-9032 Volume Control 71-2110 Panel Cartridge Lock Mechanism (for access panel) 75-07017 Spacer for Mounting Printed Circuit Boards 78-3201 Cabinet-Leveling Leg 78-6D003 Ya-Inch-Wide Adhesive Transfer Tape (for mounting overlays on monitor—2 x 9 in. required) 78-24012 5-Inch Beaded Nylon Tie Wrap (for PCB Edge Connectors) 92-045 15-Inch Quadrascan™ X-Y Monitor 00272801 Control-Panel Mounting Bracket 007882-02 Interlock Switch Cover 009992-01 On/Off Switch Cover 030249-01 Coin Box Separator 034536-02 Foam Vibration Damper (for Regulator/Audio II PCB)

034536-03Foam Vibration Damper(for Auxiliary and Analog Vector-Generator PCBs)

036130-01 Speaker Grille 036262-01 Coin Box Bracket 036263-03 Red Monitor Overlay 036263-04 Green Monitor Overlay 036669-01 Acryiic Monitor Shield 036670-01 Monitor Shield Retainer 036674-01 Attraction Panel with Graphics 036676-01 Cardboard Bezel with Graphics 148001-001 6x9-Inch 4Ohm 15-Watt Ovai High-Fidelity Speaker 035745-02 18-Inch Plastic PCB Retainer 035745-03 10-Inch Plastic PCB Retainer

Page 35

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 36

62-039

75017S

75-9910W0 NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, inc., Sunnyvale, CA. This drawing is only conditionally i issued, and neither receipt nor possession thered! | confers or transfers any right in, or license to use, the subject matter of the drawing or any design of technical intormation shown thereon, nor any Tight to reproduce this drawing or any part thereot Except for manufacture by vendors of Alati, Inc.. Control Handle Assy.— and tor manufacture under the corporation $ writ Figure 19 {en license. no right 10 reproduce this drawing is ‘See Figure granted or the subject matter thereof uniess by written agreement with or written permission trom the corporation.

03610201

036675-01

005255-04

Figure 18 Control Panel Assembly A036656-01 A

Parts List

Part No. Description

A036246-01 Control-Panel Harness Assembly 62-039 SPDT Momentary-Contact Pushbutton Start Switch with Red Light-Emitting Diode 75-017S 7/16-Inch SAE-Standard Zinc-Piated Steel Flat Piain Washer 76-9910W0 #15/32-32 Steei Stamped Nut

005255-04 Control-Handie Bezel 033127-01 Biack Molded Switch Bushing 036102-01 Wood Support Block for Control Handles 036675-01 Control Panel with Graphics

Page 37

NOTICE TO ALL PERSONS RECEIVING THIS. CONFIDENTIAL: Reproduction forbidden without the specific wiitten permission of Atari, Inc., ‘Sunnyvale, CA, This drawing Is only conditionally issued, and neither receipt nor possession thereot confers or transfers any right in, or license to use, the subject matter of the drawing or any design or technical information shown thereon, nora right to reproduce this drawing or any part thereof. Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's writ: ten license, no right to reproduce tnis drawing is Granted or the subject matter thereo! unless by written agreement with or written permission from the corporation.

The A036271-01 assembly has NO fire switch and harness (left control handle). The A036271-02 assembly HAS the fire switch and harness (right control handle).

65-021A

NOTE: . i Do not remove the flat actuator spring on Sy na ° unless you have a replacement. Remov-

VW 75-046 ing the spring will bend it, and it will no

85-22F 608 longer be usable.

Figure 19 Control Handle Assembly A036271-01 and -02 B

Page 38

Figure 19 Control Handie Assembly Parts List

Part No. Description

A036277-01 Shaft Assembly with Fire Switch Harness (includes pivot ball, pivot shaft and 2 sfotted pins) A036278-01 Shaft Assembly without Fire Switch Harness (inc/udes pivot ball, pivot shaft and 2 slotted pins) A036281-01 Centering Bellows 62-043 SPST Pushbutton Switch with Red Non-Lighting Cap (used as fire switch) 65-021A Single-Pole Single-Throw Low-Force Miniature Switch 72-1412S #4-40 x %-Inch Pan-Head Cross-Recessed Steel Cadmium-Plated Machine Screw 72-8614 #6-32 x 7/8-Inch Hex Socket-Head Steel Machine Screw 73-20809 4/8-Inch Diameter x 9/16-Inch Long Slotted Pin 73-21214 3/16-Inch Diameter x 7/8-Inch Long Slotted Pin 75-046 #6 Internal-Tooth Steel Split Lock Washer 75-944S, #4-40 Sieel Self-Locking Polymer Hex Nut 78-1710 Dow Corning Heavy Silicone Compound #111 Lubricant 85-22F608 #632 x ¥e-Inch Pan-Head Phillips Self-Threading Type F Steel Machine Screw 000609-02 Control Handle Housing (two of these required per contro! handle assembly) 005255-04 Control-Handle Bezel 035792-01 Straight-Pattern Detent 035844-01 Clear Plastic Actuator Pin 035995-01 Plastic Control Handle (Right Half) 035995-02 Plastic Control Handle (Left Half) 035997-01 Plug for Control Handle 03627601 Bezel for Fire Pushbutton 036279-01 Pivot Ball 036280-01 Pivot Shaft 036282-01 Flat Actuator Spring 178010-001 Nylon Actuator Ball 178016-001 Spring

Note: The control-handle bezel is not part of this control handle assembly. It is listed here for your convenience.
Page 39

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 40

99-11011

99-11003

99-11009

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission af Atari, Inc. Sunnyvale, CA This drawing is only conditionally issued, and neither receipt nor possession thereof confers or transfers any right in, or license to use, the subject matter of the drawing or any design ot technical information shown thereon, ner any right to reproduce this drewing oF any part thereof. Except for manufacture by vendors of Ata, Inc., and for manufacture under the corporation's written license, no right to repreduce this drawin ated or the subject matter thereof unless by written agreement with or weitten permission from the corporation. A005493-01

Figure 20 Fluorescent Light A036205-01 c

Parts List Battlezone Cabaret

035835-01

79-561816P

Part No. Description

A005493-01 Fluorescent Light Harness Assembly 70-304 18-Inch 15-Watt Cool White Fluorescent Lamp 79-581816P Wire Nut for 16- to 18-Guage Wires 99-11003 Fluorescent Lamp Starter

99-11008 Ballast Transformer 99-11009 Starter Socket 99-11011 1%-Inch Clamp 035835-01 Y-Lead Connector

Page 41

Battlezone™iCabaret

034482.02 794411006 03454401 03630401 46-2017002 46-2014001 4 OS ——’ 79-3206 a br19 A035888-01 or -02 SN, ant) A035674-01 O° OR i A035891-01 A036354-01 or -02 (Int'l) Us.)

78-2708

TOP VIEW

(F2is not used)

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the 78-70501SC specific written permission of Atari, Inc., Sunnyvale, CA This drawing Ia only conditionally’ issued. and neither 29.053 receipl nor possession thereof confers or transfers any right In, oF license to use, the subject matter of the draw ing or any design or technical intormation shown thereon, nor any Fight to reproduce this drawing or any part thereo!: Except for manufacture by vendors of Atatl Inc., and for manufacture under the corporation's wiitten license, no right to reproduce this drawing is granted or the subject matter thereof unless by written agreement with or written permission from the corporation

BOTTOM VIEW

3A-MDA3501

A035890-01 (Int'l) A034630-01 gr A036355-01 (U.S) 034629.01 7915021001

Figure 21 International and U.S. Power Supply Assemblies for X-Y Games A035892-01 (International) A / A036353-01 (U.S.) A

Page 42

Battlezone Cabaret

Figure 21 International and U.S. Power Supply Assemblies for X-Y Games Parts List

Part No. Description (Reference Designations in Bold)

A034629-01 AC. Harness Assembly A034630-01 RFI Filter Assembly (FL1) A035674-01 Voltage Plug Assembly (set of four plugs—for international power supply only) A035888-01 or 02 Transformer Assembly—international oniy (71) A035890-01 Power Harness Assembly (international only) A035891-01 Fuse Harness Assembly A036354-01 or -02 Transformer Assembly—U.S. only (T1) A036355-01 Power Harness Assembly (U.S. only) 29-053 26,000 uf 15 V Electrolytic Capacitor (C1) 3A-MDA3501 Bridge Rectifier, type MDA 3501 (CRi)

46-20140014-Amp. 125 V 3AG Slow-Blow Glass Cartridge-Type Fuse(F4, F5, Fé)
46-20170027-Amp. 250 V 3AG Slow-Blow Glass Cartridge-Type Fuse(F1)
46-30120320-Amp. 32 V 3AG Slow-Blow Glass Cartridge-Type Fuse(F3)

78-2708 Nylon Type 6/6 Hole Bushing with 5/8-Inch Inside Diameter x 55/64-Inch Outside Diameter x Y4-Inch Thick 78-70501SC 2-Inch Diameter Capacitor Mounting Bracket 79-15021001 2-Circuit Single-Row Terminal Block 79-3206 5-Position 3AG Fuse Block with %-Inch Quick-Disconnect Terminals 79-4411006 Panel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post 034482-02 Power Supply Chassis 034544-01 Fuse Block Cover 036304-01 Label for Fuse Values

Page 43

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA, This drawing is only conditionally issued, and neither receipt nor possession thereof confers or transfers any right in, oF license to use, the subject matter of the drawing of any design or technical information shown thereon, nor any right to reproduce this drawing or any part thereof. Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's written license, no right to reproduce this drawing is granted or the subject matter thereof unless by written agreement with or written permission from the corporation.

Oy

1415374

Rae picam 137004 ¢

  • si6H

co1z294-01 4

&

(Gercerretertors Serres ia ) c2e aD

raceoReyEC
| ESESESPayracere

emcees nn. EE RS6

SPARES7109¢SPARE
ele,SPAREQSPARE

ci 26 ab cai == Te

ccsc10clecsR37
QDQDxooSsp =.cae
[saree(Fatsz73¢SPARE‘SpaRe ¢evaee,B38Onvsoss

~ Raa veseie ee teense e488

ele [ S 7 aL

+ q v8) = '

EE gy Gh 137004 pirorey : Peceae ECE

a7Ji
  • zo '

FER R34 IK oz 2 aa RRS gh C7 _ <> 74505 T

Figure 22 Battlezone™ Auxiliary PCB Assembly A035678-01

Page 44

Figure 22 Battlezone™ Auxiliary PCB Assembly Parts List

Part No. Description (Reference Designations and Locations in Bold)

€012294-01 Audio /O N-Channel MOS/LS! Custom Chip (B/C2) 19-315254 250K Ohm Vertical PCB-Mounting Cermet Trimpot (R11) 21-101153, .015 uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (C11, C25) 21-101472 .0047 uf, +10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (C21, 22)

21-101474.47 uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor(C29)
24-25010610 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor(C13, 14)
24-250107100 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor(C27)
24-250475,4,7 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor(C9)

24-250477 470 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C28) 29-088 -1 uf Ceramic-Disc Radial-Lead 25V Capacitor (C1-8, 10, 12, 15-20, 23, 24, 26, 30-35)

31-1N91475V Type-1N914 Switching Diode(CR1)
37-LM324Type LM324 Integrated Circuit(K5, M5)

37-4066 Type 4066 Analog Switch Integrated Circuit (3, 14)

37-555Type 555 Timer Integrated Circuit(F3)
37-74LS00Type 74LS00 Integrated Circuit(D3)
37-74LS02Type 74LS02 Integrated Circuit(D4)

37-74LS04 Type 74LS04 Integrated Circuit (E4)

37-74LS20Type 74LS20 integrated Circuit(J4)
37-74LS32Type 74LS32 Integrated Circuit(C4)
37-74LS74Type 74LS74 Integrated Circuit(C5, J5)
37-74LS139Type 74LS139 Integrated Circuit(C3)

37-74LS161 Type 74LS161 Integrated Circuit (D1, E1, F4, F5) 37-74LS 164 Type 74LS164 Integrated Circuit (H4, H5)

37-74LS273Type 74LS273 Integrated Circuit(M2)
37-74L.S374Type 74LS374 Integrated Circuit(C1)
37-74808Type 74808 Integrated Circuit(D5)
37-74109Type 74109 Integrated Circuit(B4)

36-MV5053, Type MV5053 Red Light-Emitting Diode (CR2)

79-421616-Contact Medium-Insertion-Force Integrated Circuit Socket(B14, F1, H1, J1, K1, L1, M1)
79-42G4040-Contact Medium-insertion-Force Integrated Circuit Socket(B/C2, D/E2, F2, H/J2, K2)

020670-01 Test Point

036174-01Programmable Read-Only Memory(B1)
036175-01Programmable Read-Only Memory(M1)
036176-01Programmable Read-Only Memory(L1)
036177-01Programmable Read-Only Memory(K1)
036178-01Programmable Read-Only Memory(J1)

036179-01 Programmable Read-Only Memory (H1)

036180-01Programmable Read-Only Memory(F1)
110000-1021K Ohm, + 5%, %W Resistor(R2, 3, 5, 7, 15, 16, 22, 38, 46-52)

110000-103 10K Ohm, + 5%, %4W Resistor (R13, 18, 30, 36)

Page 45

Battlezone ™/Cabaret

Figure 22 Battlezone™ Auxiliary PCB Assembly, continued Parts List

Part No. Description (Reference Designations and Locations in Bold)

110000-104 100K Ohm, + 5%, %4W Resistor (R8, 10, 23-25, 28, 31) 110000-151 150 Ohm, + 5%, YW Resistor (R37, 45) 110000-223 22K Ohm, + 5%, YW Resistor (R9, 14, 17, 29) 110000-333 33K Ohm, + 5%, YW Resistor (R12, 19-21, 26, 34, 35) 110000-334 330K Ohm, + 5%, %W Resistor (R27, 32, 33) 110000-471 470 Ohm, x 5%, %4W Resistor (R1, 39-44) 410000-472 4.7K Ohm, + 5%, ¥4W Resistor (R6) 137002-001 Type 74886 Integrated Circuit (E5) 137003-001 Type 74803 Integrated Circuit (E3) 137004-001 Transistor Array (D/E2, F2, HIJ2, K2) 179010-001 12-Pin PCB Header

Page 46

Figure 23 Battlezone™ Analog Vector-Generator PCB Assembly A036424-02 A Reed 88 baad Res (sal 6 gins | gees Fea jens —

= ue Sh i a i: pee * OY

Gir iz 22 ia Do sae -- =

Page 47

Figure 23 Battlezone™ Analog Vector-Generator PCB Assembly Parts List

Memory Components and Their Equivalents (Locations Shown in Bold)

-02 P.C. Boards (ROMs)

036409-01

036410-01

036411-01

036412-01

036413-01

036414-02

036421-01

036422-01 (N41)

(uM)

(K1)

(1)

(FIH1)

(E1)

(A3)

(BIC3)

Page 48

Battlezone Cabaret

Figure 23 Battlezone™ Analog Vector-Generator PCB Assembly, continued Parts List

Note: The Battlezone™ Analog Vector-Generator PCB consists of the Battlezone memory chips (described on the previous page in the Memory Equivalents Table) PLUS the Universal Vector- Generator PCB. The latter is interchangeable with Baitlezone and future X-Y games, but not with Lunar Lander™ or Asteroids™. All the following parts in this figure make up the Universal Vector-Generator PCB Assembly.

Part No. Description (Reference Designations and Locations in Bold)

Universal Vector-Generator PCB Assy., A035742-01 and -02, Rev. B, consists of the following parts: 19-007 10K Ohm, + 20%, 1%W 8-Pin Dual-Intine-Package Resistor Network (RP1, RP2—use only if board has 74LS170s or 74LS670s at locations E6, F6, H6) 19-315103 10K Ohm Vertical PCB-Mounting Cermet Trimpot (R88, 98) 19-315201 200 Ohm Vertical PCB-Mounting Cermet Trimpot (R73, 74) 21-101102 .001 uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (C69, 70, 93, 94) 21-101103 .01 uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (For -02 PCB Assy. only: C103) 21-101473 047 uf, +10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (C56, 59) 24-250106 10 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C17, 18) 24-250107 100 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C78, 83-86) 24-500105 1 uf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor (C30, 89, 90) 27-102182 .0018 pf, + 10%, Radial-Lead Ceramic-Disc 1000V Capacitor (For -01 PCB Assy. only: C103. For -02 PCB Assy. only: C105)

28-10110010 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor(C44)
28-101101100 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor(C27)

28-101151 150 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C63) 28-101221 220 pf Radiai-Lead Epoxy-Dipped 100V Mica Capacitor (C82)

28-10139039 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor(C25, 64)
28-10147047 pt Radial-Lead Epoxy-Dipped 100V Mica Capacitor(C104)

29-006 1 uf, +10%, 35V Tantalum Capacitor (C88) 29-088 .1 uf Ceramic-Disc 25V Radial-Lead Capacitor (C1-16, 19-23, 26, 28, 29, 31-39, 45, 46, 50-54, 61, 72-77, 79-81, 97, 98. Also, for -01 PCB Assy. only: C40, 41, 48, 49. For -02 PCB Assy. only: C42, 43, 50, 51) 31-1N100 100V Type-1N100 Switching Diode (CR11) 31-1N914 75V Type-1N914 Switching Diode (CR1, 3-10) 33-2N3906. Type-2N3906 PNP Switching and Amplifying Transistor (Q3, 7) 34-2N3904 Type-2N3904 NPN 60V 1-Watt Transistor (Q1, 2, 8, 9) 34-2N6044 Type-2N6044 Darlington NPN Transistor (Q4-6)

37-LM319Type M319 Integrated Circuit(B12, D12)
37-TLO82CPType TLO82 Integrated Circuit(A10, D10)
37-13201Type LF13201 Integrated Circuit(B10, D11, E10)
37-347Type TLO84 integrated Circuit(C11)
37-74LS00Type 74LS00 Integrated Circuit(J4)
37-74LS02Type 74LS02 Integrated Circuit(N9, M7)
37-74LS08Type 74LS08 Integrated Circuit(L5, P8)
37-74LS10Type 74LS10 Integrated Circuit(K4)
37-74LS14Type 74LS14 Integrated Circuit(B6)
37-74LS20Type 74LS20 Integrated Circuit(M5)
37-74LS27Type 74LS27 Integrated Circuit(N7)

ra

Page 49

Figure 23 Battlezone™ Analog Vector-Generator PCB Assembly, continued Parts List

Part No. Description (Reference Designations and Locations in Bold)

Universal Vector-Generator PCB Assy., A035742-01 and -02, Rev. B, consists of the following parts: 37-74LS32 Type 74LS32 Integrated Circuit (J5, K10, L2, M8)

37-74LS42Type 74LS42 Integrated Circuit(B4, J7)
37-74LS74Type 74LS74 Integrated Circuit(H10, L10, M9)
37-74LS86Type 74LS86 Integrated Circuit(D7)
37-74LS109Type 74LS109 Integrated Circuit(N8)
37-74LS139Type 74LS139 Integrated Circuit(C4, K5, M2)
37-74LS157Type 74LS157 Integrated Circuit(D4, E4, F4, H4)
37-74LS161Type 74LS161 Integrated Circuit(K6, L4, L6, M6, N6)

37-74LS164 Type 74LS164 Integrated Circuit (P9) 37-74LS174 Type 74LS174 Integrated Circuit (C7, L7, M11)

37-74LS175Type 74LS175 Integrated Circuit(F8, F9, J8, K8)
37-74LS191Type 74LS191 Integrated Circuit(F10, J6)
37-74LS193Type 74LS193 Integrated Circuit(E5, F5, H5)
37-74LS194Type 74LS194 Integrated Circuit(A5, A6, B5, C5, D5, D6)
37-74LS244Type 74L8244 Integrated Circuit(K3, N2, N11, P11, R11)7
37-74LS245Type 74LS245 Integrated Circuit(F2,P2,P4) Acceptable substitute is part no. 37-8304B.
37-74LS273Type 74LS273 Integrated Circuit(C8)

37-74LS367 Type 74LS367 Integrated Circuit (F7, H7) 37-74LS393 Type 74LS393 Integrated Circuit (M4, N5)

37-74LS399Type 74LS399 Integrated Circuit(H8)
37-74LS670Type 74LS670 Integrated Circuit(E6, F6,H6) Acceptable substitute is part no. 37-74LS170.
37-74S00Type 74800 Integrated Circuit(C6)
37-7402Type 74802 integrated Circuit(K9)
37-74804Type 74S04 Integrated Circuit(K2, R9)
37-14S74Type 74S74 Integrated Circuit(J10, L9)
37-748260Type 748260 Integrated Circuit(L8)
37-7404Type 7404 Integrated Circuit(H11)
37-74193Type 74193 Integrated Circuit(N4)

37-7805 +5V Voltage Regulator (VR2) 37-7815 + 15V Voltage Regulator (VR3) 37-7915 — 15V Voltage Regulator (VR1)

38-MV5053Type MV5053 Light-Emitting Diode(CR2)

41-3004 100 uH, + 10%, Hot-Molded Plastic Fixed R.F. Choke (L1) 62-001 SPST Momentary Pushbutton Switch (SW1) 66-114P1T 4-Station Single-Throw, Dual-Inline-Package Bit Switch (L11) 66-118P1T 8Station Single-Throw, Dual-Inline-Package Bit Switch (M10, P10) 7179-42024 24-Contact Medium-Insertion-Force Integrated Circuit Socket (A3, B/C3, D3, E1, E3, F/H1, F/H3, J1, J3, K1, M1, N14) 79-42C40 40-Contact Medium-Insertion-Force Integrated Circuit Socket (L/M/N3) 81-4302 Nylon Snap-In Fastener

90-10212.096 MHz, + .005%, Crystal(¥2)

90-6013 Microprocessor (L/M/N3) 90-7033 Random-Access Memory (A1, A2, B1, B2, C1, C2, D1, D2, H2, J2) 020670-01 Test Point

036408-01Programmable Read-Only Memory(K7)
Page 50

Figure 23 Battlezone™ Analog Vector-Generator PCB Assembly, continued Parts List

Part No. Description (Reference Designations and Locations in Bold)

Universal Vector-Generator PCB Assy., A035742-01 and -02, Rev. B, consists of the following parts: 110000-101 100 Onm, +5%, %4W Resistor (R70, 75)

110000-1021K Ohm, +5%, 4W Resistor(R18, 20, 27, 67, 84-86, 94, 110, 128-133)

410000-103 120 Ohm, +5%, “4W Resistor (R1-17, 19, 21, 25, 26, 33, 44, 51-66, 95, 99, 125-127. In addition, for -01 PCB Assy. only: R48, 50, 69)

110000-104100K Ohm, +5%, YW Resisior(R35-42)

110000-122 1.2K Ohm, +5%, VW Resistor (R46) 110000-151 150 Ohm, +5%, “W Resistor (R103) 110000-153 15K Ohm, +5%, %W Resistor (R93)

110000-221220 Ohm, +5%, YW Resistor(R24)

110000-222 2.2K Ohm, +5%, VW Resistor (R45, 92, 102, 112, 114-116, 119-121, 123)

110000-22322K Ohm, +5%, %4W Resistor(R28-32)

110000-270 27 Ohm, +5%, YW Resistor (R111) 110000-332 3.3K Ohm, +5%, YW Resistor (R87, 97)

110000-3923.9K Ohm, +5%, YW Resistor(R47, 49)

110000-471 470 Ohm, +5%, %W Resistor (R34, 104-109)

110000-4724.7K Ohm, +5%, %4W Resistor(R43)
110000-474470K Ohm, +5%, YW Resistor(R113, 117, 118, 122)

110000-561 560 Ohm, +5%, 4W Resistor (R96) 110000-680 68 Ohm, +5%, ¥4W Resistor (R124) 140000681 680 Ohm, +5%, “4W Resistor (For -02 PCB Assy. only: R83) 110000-821 820 Ohm, + 5%, YW Resistor (For -02 PCB Assy. only: R68, 69, 82) 110003-752 7.5K Ohm, + 1%, 1/8W Metal-Film Resistor (R71, 72, 76-81, 89) 122000-225 2.2 uf, + 10%, 35V Tantalum Capacitor (C87) 422005-103 .01 uf Ceramic-Disc Minimum 25V Radial-Lead Capacitor (C47, 55, 57, 58, 60, 62, 65-68, 71, 91, 92, 95, 96, 99, 100) 137002-001 Type 74886 Integrated Circuit (B7)

137149-001Type 74LS11 Integrated Circuit(J9)

137159-001 Type DAGC-08 Digital-to-Analog Converter (C9) 137158-002 Type AM6012ADC Digital-to-Analog Converter (A9, D9) For -02 PCB Assemblies only OR OR 137160-003 Type MC3410 Digital-to-Analog Converter (B9,E9) For-07 PCB Assemblies only 179010-001 12-Pin PCB Header (J19)

Page 51

30IS 31LISOddO NO 3YVv NMOHS S30VeL

7812 NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the Specific written permission of Atari, Inc., Sunnyvale, CA, This drawing is only conditionally issued, ard neither receipt Nor possession thereof confers or transfers any Fight in, or license to use, the subject matter of the draw: ing or any design or technical information shown thereon, nov any right’to reproduce this drawing or any part thereof. Except for manufacture by vendors of Atari, inc., and for manufacture under the corporation's written license, no right to reproduce this drawing is granted or the subject matter thereof unless by written agreement with or written permission from the corporation.

Figure 24 Regulator/Audio Il PCB Assembly A035435-02 c

Page 52

Figure 24 RegulatoriAudio Il PCB Assembly Parts List

Part No. Description (Reference Designations and Locations in Bold)

12:52P72.7 Ohm, + 5%, iW Resistor(R5)

16-54PO 4 Ohm, +5%, SW Wirewound Resistor (R25) 19-100P1015 .1 Ohm, + 3%, 7W Wirewound Resistor (R24) 19-315102 1K Ohm Vertical PCB-Mounting Cermet Trimpot (R8)

24-2501081000 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor(C13)
24-250477470 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor(C1, 4, 12)

24-350226 22 uf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor (C24, 31)

24-3503383300 uf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor(C9, 10, 18, 19)

24-500105 1 uf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor (C22, 23) 29-088 .1 uf Ceramic-Disc 25V Radial-Lead Capacitor (C3, 11, 20, 21) 31-A14F 50V 2.5A Miniature Axial-Lead High-Current Rectifier (CR1, 4-8)

33-TIP32PNP Power Transistor, Type TIP32(Q2)
34-2N3055,NPN Silicon Transistor, Type 2N3055(Q3)

37-LM305 5V Linear Voltage Regulator (Q1)

37-7812+12V Voltage Regulator, Type 7812(Q8)
37-7908—~5V Voltage Regulator, Type 7805(Q9)

72-1608C #6-32 x ¥2-Inch Cross-Recessed Pan-Head Corrosion-Resistant Steel Machine Screw 75-F60405, #6-32 x 14-Inch Binder-Head Nylon Screw 75-99516 #6-32 Nut/Washer Assembly

78-16008Thermally Conductive Compound(Q3)

78-16014 Thermally Conductive Silicon Insulator (Q2, 9)

79-583066-Position Connector Receptacle(J6, 9)

79-58308 QPosition Connector Receptacle (J7)

79-5834612-Position Connector Receptacle(J10)
79-583544-Position Connector Receptacle(J8)

020670-01 Test Point 034531-01 Heat Sink 1410000-010 1 Ohm, + 5%, %W Resistor (R10, 19) 110000-100 40 Ohm, + 5%, %4W Resistor (R11, 20, 29, 30) 110000-101 100 Ohm, + 5%, YW Resistor (R4, 12, 22)

110000-1021K Ohm, + 5%, %W Resistor(R27, 28)
110000-10310K Ohm, + 5%, %4W Resistor(R13, 14)
110000-271270 Ohm, + 5%, “W Resistor(R1)

410000-330 33 Ohm, + 5%, %W Resistor (R3) 110000-392 3.9K Ohm, + 5%, %4W Resistor (R6)

110000-5625.6K Ohm, + 5%, %W Resistor(R32, 33)

110000-752 7.5K Ohm, + 5%, %4W Resistor (R7)

110001-221220 Ohm, + 5%, YW Resistor(R9, 21)

116000-220 22 Ohm, + 5%, 10W Wirewound Resistor (R31) 122002-102 .001 uf Ceramic-Disc 35V Radial-Lead Capacitor (C2, 7, 16)

122004-224.22 uf Ceramic-Disc 25V Capacitor(C6, 8, 15, 17)

122005-103 .01 uf Ceramic-Disc 25V Radiai-Lead Capacitor (C5, C14) 137151-002 Type TDA2002A 8W Linear Audio Amplifier Integrated Circuit (Q5, 7)

Page 53

COIN INLET CHUTE

70-11-47

COIN MECHANISM SEE PARTS LIST i

99-0102 COIN RETURN —99-10065 SWITCH WIRE CHUTE 99-10068 _/ SEE PARTS LIST (90-10075 thru » 99-1007 Naoo2 COIN SWITCH ASSY. a 10004 PART OF 99-1047 SEE PARTS LIST ge-10062 (9-10042 thru 7514128 99-1045)

Figure 25 Coin Door 71-10xXxx

Page 54

COIN RETURN BUTTON ASSY.— SEE PARTS LIST (99-10012 thru 99-10022, and 98-10107)

COIN DOOR ONLY— SEE PARTS LIST (99-10009 and 10010)

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc,, Sunnyvale, CA. This drawing is only conditionally issued, and neitner receipt nor possession thereot conlers or transfers any right in, of license to use, the subject matter of the drawing or any design oF echnical information shown thereon, nor any tight to raprodute this drawing or any part thereof, Except for manviacture by vendors of Atari, Inc., and fof manufacture under the corporation's writ: ten license, no right to reproduce this drawing is granted or ‘the subject matter thereof uniess by written agreement with or written permission trom the corporation. 75-5520B COIN RETURN BUTTON COVER— SEE PARTS LIST (99-10055 thru 99-10059)

PRICE PLATE— SEE PARTS LIST (89-10070, $9-10083 thru 99-10092, and 99-10108) 99-10074

72-JA1405B

99-10062

72-HA1404C

75-915S |

72-JA1405B

Figure 25 Coin Door 71-10xxxx

Page 55

Figure 25 Coin Door, continued Parts List

Part No. Description

31-1N4002 100V Silicon Rectifier 1N4002 Diode 65-4410 General-usage low-force miniature switch 70-11-47 Miniature bayonet-base incandescent lamp, type #47 71-1201ADU U.S. $1.00 coin mechanism 71-1201FCH Swiss 1 Fr coin mechanism 71-1201MG German 1 DM coin mechanism 71-1202MG German 2 DM coin mechanism 71-1205FB Belgian 5 Fr coin mechanism 71-1205MG German 5 DM coin mechanism 71-1210PE U.K. 10 P coin mechanism 71-1220CA Australian 20¢ coin mechanism 71-1225CU U.S. 25¢ coin mechanism 71-12100LI Italian 100 Lire coin mechanism 71-12100YJ Japanese Y100 coin mechanism 72-HA1404C #4 x ¥%4-Inch slotted pan-head thread-rolling tri-fluted “Taptite” cadmium-plated screw 72-JA1405B #4 x 5/16-Inch slotted pan-head thread-rolling tri-fluted ““Plastite” black screw 72-9406S #4-40 x 3/8-Inch slotted truss-head steel machine screw 72-9603S #6-32 x 3/16-Inch slotted truss-head steel machine screw 75-915S #%-20 Standard pattern cadmium-plated steel hex nut 75-918S, #8-32 Standard pattern cadmium-plated steel hex nut 75-9445, #4-40 Polymer self-locking steel hex nut 75-948S, #8-32 Polymer self-locking steel hex nut 75-1408S, #4-40 x ¥2-Inch slotted pan-head steel machine screw 75-1412S #4-40 x %4-Inch slotted pan-head steel machine screw 75-5520B #%-20 x 1%-Inch round-head square-neck steel bolt with black finish 99-10008 Switch wire retainer 99-10009 2-Mech coin door only 99-10010 3-Mech coin door only 99-10011 Inner panel 99-10012 U.S. 25¢ coin return button assembly 99-10013 U.S. $1.00 coin return button assembly 99-10014 German 1 DM coin return button assembly 99-10015. German 2 DM coin return button assembly 99-10016 German 5 DM coin return button assembly 99-10017 Belgian 5 Fr coin return button assembly 99-10018 Swiss 1 Fr coin return button assembly 99-10019 Japanese Y100 coin return button assembly 99-10020 U.K. 10 P coin return button assembly 99-10021 Australian 20¢ coin return button assembly 99-10022 Italian 100 Lire coin return button assembly

Page 56

Figure 25 Coin Door, continued Parts List

Part No. Description

99-10045, Coin switch assembly for German 5 DM, U.K. 10 P, and Australian 20¢ coins (green wire) 99-10047 Lockout coil assembly 99-10048 Coin door harness assembly 99-10049 Locking arm assembly 99-10051 Coin door frame 99-10052 Coin return lever 99-10054 Coin button housing 99-10055 Coin return button cover for Japanese Y100 coin 99-10056 Coin return button cover for German 1 DM and Swiss 1 Fr coins 99-10057 Coin return button cover for U.S. 25¢ and Belgian 5 Fr coins 99-10058 Coin return button cover for U.S. $1.00, German 2 DM, and Italian 100 Lire coins 99-10059 Coin return button cover for German 5 DM, U.K. 10 P, and Australian 20¢ coins 99-10061 Coin return bezel 99-10062 Coin return button 99-10063 Right half of coin inlet chute 99-10064 Left half of coin inlet chute 99-10065 Coin return box 99-10066 Coin return cover 99-10070 U.S. 25¢ price plate 99-10071 Slam switch assembly 99-10073 Test switch decal 99-10074 Lock assembly 99-10075 Black switch wire—for German 1DM, Swiss 1Fr and Japanese Y100 coins 99-10076 Silver switch wire—for U.S. 25¢ and Belgian 5Fr coins 99-10077 Gold switch wire—for U.S. $1.00, German 2DM and Italian 100 Lire coins 99-10078 Green switch wire—for German 5DM, U.K. 10P and Australian 20¢ coins 99-10080 Miniature bayonet-base lamp socket 99-10081 Wire key holder 99-10082 Switch cover 99-10083 U.S. $1.00 price plate 99-10084 German 1 OM price plate 99-10085 German 2 DM price plate 99-10086 German 5 DM price plaie 99-10087 Belgian 5 Fr price plate 99-10088 Swiss 1 Fr price plate 99-10089 Japanese Y100 price plate 99-10090 UK. 10 P price plate 99-10091 Australian 20¢ price plate 99-10092 Italian 100 Lire price plate 99-10094 Fish paper insulation 99-10095 Toggle switch 99-10096 “U"-type fastener 99-10097 Fish paper insulation 99-10101 Coin inlet chute sub-assembly 99-10102 Switch and lockout coil bracket sub-assembly 99-10103 Inner panel with levers sub-assembly 99-10104 Anti-penny-flip bar retainer 99-10105 Anti-penny-flip bar 99-10107 U.S. 50¢ coin return button assembly 99-10108 U.S. 50¢ price plate—for two quarters

Page 57

1st printing

YOUR COMMENTS, PLEASE!

Your comments will assist Atari in improving the usefulness of our publications. They are an important part of preparing for revisions of manuals and parts catalogs. No postage stamp is necessary if mailed in the U.S.A.

If you have any technical questions about certain Atari or Kee Games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply:

Name Firm Distributor

Address — Ol Operator

City _ State _ Zip C1 Other.

Page 58

First fold

BUSINESS REPLY MAIL

FIRST CLASS PERMIT NO. 1004 SUNNYVALE, CA

POSTAGE WILL BE PAID BY ADDRESSEE

Atari, Inc. Attn.: Field Service/Coin-Op Division P. O. Box 427 Sunnyvale, California 94086 No Postage Necessary if mailed in the United States

=~

eur) siyy Buoy "ND

Sacond fold

eBpa sy edey swol4

Page 59

ES

be

Warranty

Seller warrants that its printed circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its television monitors (in games supplied with monitors) are free from defects in material and workmanship under normal use and service for a period of thirty

  • days from date of shipment. None of the Seller's other products or parts thereof are warranted.

If the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are returned to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
  • Such products are returned prepaid to Sellers’ plant; and
  • Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing.

In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages.

Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms of this order, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products under this order.

The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to yourself and others. Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety.

Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.

This document is and contains confidential trade secret information of Atari, Inc.

This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc.

Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc. SASS EAS AS ES aS ASS

Page 60

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.