CATHODE RAY TOMES

Return of the Jedi TM-227 1st Printing

Return of the Jedi (Atari, 1984) · Technical Manual · 80 pages · 67 sections · original scan

Page 1
Scan of page 1

This page is a drawing, shown as the original scan.

Page 2

Atari Customer Service

Ifrcading through this manual does not lead to solving a certain maintenance problem, call TELEHELP® at one of these Atari Customer Service offices:

UNITED STATES

Parts and Service

Atari, Inc, California Customer Service Office 37 Sycamore PO, Box 906 Milpitas, CA 95045, Telex 17-2976 (Monday-Friday, 7:30-4:00 pm Pacific Time) ZS (408) 943-1120

EUROPE

Parts and Service

Atari Ireland Limited European Customer Service Office Tipperary Town, Ireland Telex 28165 (Monday-Friday, 9:00-6:00 pm GMT BZ 062-52155

Page 3

Operators Manual

With Illustrated Parts Lists

Page 4

RETURN OF THE JEDI

© 1984 by Atari, Inc. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form ofa phonographic recording, nor may it be stored ina retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for increased penalties for violating federal copyright laws, Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. In.addition, the Act provides for payment of statutory damages of up to $250,000 in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years.

Atari will aggressively enforce its copyrights against any infringers, We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game,

Published by: Atari, Inc. 1501 McCarthy Blvd. PO. Box 906 Milpitas, California 95035

Printed in the U.S.A. 8N

Page 5

RETURN OF THEJED1

Notice Regarding Non-Atari Parts

Use of non-Atari parts or modifications ofany ATARI® game circuitry may adversely affect the safety of your game, and may cause injury to you and your players,

You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following: © Substitute non-Atari parts in the game. © Modify or alter any circuits in the game by using kits or parts not supplied by Atari

NOTE

This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications, It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated. ina commercial environment. Operation of this equipment ina residential area or modification to this equipment is likely to cause interference in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from an ATARI® game at your location, check the following:

  • All green ground wires in the game are properly connected as shown in the game wiring diagram. ¢ The power cord is properly plugged into a grounded three-wire outlet. © The game printed-circuit boards (PCB) are properly installed within the Electromagnetic Interference (EMI) cage.
  • The EMI Shield PCB is properly installed and connected in series with the game PCB harness. © All filter capacitors required on the EMI Shield PCB are properly soldered in place. If you are still unable to solve the interference problem, please contact Atari Customer Service. See the inside front cover of this manual for service in your area.

iii

Page 6

RETURN OF THE JEDI

*Removing the Control Panel . .

4 Troubleshooting Table of Contents

1 SetUp How to Use This Manual 11 Game Overview 13 Inspecting the Game ............ . 13 Voltage-Plug Selection and Fuses Switch Information Option Settings . . . Game Play High-Score Mode SelfTest Mode ............. Glossary of Terms

2 Self-Test SelfTest DisplayS «1.0... eee ete 2-2

3 Maintenance Preventive Maintenance Preventive-Maintenance Intervals ... .

Lubricating the Flight Control . Tightening the Flight-Control Hardware .... Cleaning the Coin Mechanism Cleaning the Cabinet and Display Shield ... .

Corrective Maintenance . Flight Control ............... Aligning the Flight-Control Potentiometers . Calibrating the Flight Control Removing the Display Shield and Bezel Removing the Display Removing the Light-Panel Assembly ... . Removing the Speakers

Troubleshooting Aids Troubleshooting Procedures Troubleshooting Techniques Soldering Techniques . .. - Troubleshooting Static-Sensitive Devices.

Page 7

RETURN OF THF JEDI

5 Illustratea rarts Lists Figure 5-1 Cabi ti i Figure 5-2 Control Panel Assembly . . Figure 5-3 Flight-Control Assembly ... Figure 5-4 Fluorescent Tube Assembly . Figure 5-5 Power Supply Assembly .. . . Figure 5-6 Utility Panel Assembly Figure 5-7 Coin Controls, Inc. Coin Door Assembly Figure 5-8 Coin Acceptors, Inc. Coin Door Assembly . Figure 5-9 Printed-Circuit Board Mounting Hardware . Figure 5-10 Main Printed-Circuit Board Assembly. . . Figure 5-11 PIXI II Printed-Circuit Board Assembly . Figure 5-12 Regulator/Audio 11 Printed-Circuit Board Assembly.............. 5-34

List of Illustrations

Figure 1-1 Game Overview 12 Figure 1-2 Voltage-Plug Selection and Fuse Locations . 14

Figure 2-1 RAM/ROM Test—Passes 2-2 Figure 2-2 RAM/ROM Test—Fails . . . 2-2 Figure 2-3 Statistics ....... 23 Figure 2-4 Game Options . . 23 Figure 2-5 Sound Processor Test 23 Figure 2-6 Control Test... . 2-4 Figure 2-7 Color Bars ... 2-4 Figure 2-8 Grid Pattern . 25.

Figure 3-1 Removing the Control Panel and Flight Control . . 3-2 Figure 3-2 Flight-Control Handle Assembly 33 Figure 3-3 Flight-Control Steering Assembly 3-4 Figure 3-4 Removing the Video Display and Light-Panel Assembly 3-4

Figure 4-1 Removing IC (Cut Pin Method) . 43 Figure 4-2 Removing IC Pins 43 Figure 4-3 Removing Solder from PlatedThrough Holes . . oo. 44 Figure 4-4 Removing Solder from Lead Connection Pads ..........0.000 005 4-4

List of Tables

Table 1-1 Installation Specifications . . 13 Table 1-2 Coin and Credit Settings 1-5 Table 1-3 Game Option Settings . . fet feng utes 15 Table 3-1 Recommended Preventive-Maintenance Intervals .. . 3-1

Page 8

RETURN OF THE JEDI

vi

Safety Summary

The following safety precautions apply to all game operators and service personnel. Specific warnings and cautions will be found throughout this manual where they apply.

A WARNING A

Properly Ground the Game. Players may receive an electrical shock if this game is not properly grounded! To avoid electrical shock, do not plug in the game until it has been inspected and properly grounded. This game should only be plugged into a grounded 3-wire outlet. If you have only a2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electrical shock if the control panel is not properly grounded! After servicing any parts on the control panel, check that the grounding clip is firmly secured to the metal tab on the inside of the control panel. Only then should you lock up the game. AC Power Connection. Before connecting the game to the AC power source, verify that the proper voltage-selection plug is installed on the game’s power supply. Disconnect Power During Repairs. To avoid electrical shock, disconnect the game from the AC power source before removing or repairing any part of the game. When removing or repairing the video display, extra precautions must be taken to avoid electical shock because high voltages may exist within the display circuitry and cathode-ray tube (CRT) even after power has been disconnected. Do not touch internal parts of the display with your hands or with metal objects! Always discharge the high voltage from the CRT before servicing this area of the game. To discharge the CRT: Attach one end of a large, well-insulated, 18-gauge jumper wire to ground. Momenurily touch the free end of the grounded jumper to the CRT anode by sliding it under the anode cap. Wait two minutes and discharge the anode again. Use Only ATARI Parts. To maintain the safety integrity of your ATARI game, do not use non- Atari parts when repairing the game. Use of non-Atari parts or other modifications to the game circuitry may adversely affect the safety of your game, and injure you or your players. Handle Fluorescent Tube and CRT With Care. If you drop a fluorescent tube or CRT and it breaks, it may implode! Shattered glass can fly six feet or more from the implosion. Use the Proper Fuses. To avoid electrical shock, use replacement fuses which are specified in the parts list for this game. Replacement fuses must match those replaced in fuse type, voltage rating, and current rating. In addition, the fuse cover must be in place during game operation.

CAUTION

Properly Attach All Connectors. Make sure that the connectors on each printed-circuit board (PCB) are properly plugged in. Note that they are keyed to fit only one way. If they do not slip on easily, do not force them, A reversed connector may damage your game and void the warranty. Ensure the Proper AC Line Frequency. Video games manufactured for operation on 60 Hz line power (i.e., United States) must not be operated in countries with 50 Hz line power (ie., Europe). The fluorescent light ballast transformer will overheat, causing a potential fire hazard if 60 Hz games are operated on power lines using 50 Hz. Check the product identification label of your game for the line frequency required.

Page 9

To avoid electrical shock, do not plug in the game until it has been properly inspected and set up for the line voltage in your area. This game should only be connected to a grounded 3-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electrical shock if this game is not properly grounded. Do nottouch internal parts of the display with your hands or with metal objects!

Set Up

How to Use This Manual

This manual, written for game operators and service technicians, describes how to set up, maintain, and service your new ATARI game. Chapter 1 provides a game overview, game specifications, inspection procedures, switch information, option information, and a description of game play. Chapter 2 provides self-test procedures. Chapter 3 provides maintenance and repair procedures. Chapter 4 provides troubleshooting procedures. Chapter 5 provides illustrated parts lists. Schematic diagrams of the game circuitry are included in the SP-227 supplement to this manual.

Page 10

Set Up RETURN OF THE JEDI

Attraction Panel Assy Head Assy See Figure 5-1 See Figure 5-1 Fluorescent Tube Assy See Figure 5-4 Video Display « Game Identification Label x See Service Manual and Figure 3-4

Speaker Head Access Panel

See Figure 5-1 >

Flight-Control Assy See Figure 5-3

Control Panel Assy ‘See Figure 5-2

Game PCBs x See Figures 5-9-5-11 ity Panel Assy See Figure 5-6

Regulator/Audio Il PCB See Figure 5-9 and 5-12

Body Assy See Figure 5-1

Coin Door Assy See Figures 57 & 58

Power Supply Assy * See Figure 5-5

WARNING Do not plug in the game until it has been inspected. This game should only be connected to a grounded

3.wire outlet. Ifyou have only a2-wire

outlet, we recommend you hire a jicensed electrician to insiall a grounded outlet, Players may receive an electrical shock if this game is not properly grounded! Power On/Off Switch

Pedestal Assy See Figure 5-1

x Items with a serial number label.

Figure 1-1 Game Overview

Page 11

RETURN OF THE JEDI

Game Overview

RETURN OF THEJEDI" is the latest coin-operated adventure game from Atari. RETURN OF THEJEDI is a one-player game that features the thrills and excitement of the continuing STAR WARS* saga. The new split-wave game-play feature cuts back and forth between two simultaneously occurring action scenes, just like the movie. For an overview of the cabinet and main assemblies see Figure 1-1.

Inspecting the Game

Do not plug in the game until you have completed steps 1 through 3!

Please inspect your game carefully to ensure that it was delivered to you in good condition. Table 1-1 lists space, power, and other environmental requirements for this game.

  • Examine the exterior of the game cabinet for dents, chips, or broken parts.
  • Remove the screws from the body access panel. Unlock and open this panel and the coin door. Inspect the interior of the game as follows: a. Ensure that all plug-in connectors (on the game harnesses) are firmly plugged in. Replug any connectors found unplugged. Do not force connectors together. The connectors are keyed so they only fit in the proper orientation. A reversed edge connector may damage a printed-circuit board (PCB) and will void your warranty. b. Ensure that all plug-in integrated circuits on the game PCB are firmly plugged into their sockets. c. Remove the power cord from the clamp at the back of the cabinet. Inspect the power cord for any cuts or dents in the insulation. Repair or replace it, if required. d. Inspect the power supply. Make sure the harness is plugged in correctly and that the fuse-block cover is mounted in place. Check that the green ground wire is connected. e. Inspect other major subassemblies, such as the control panel, video display, PCBs, speakers, and the fluorescent tube. Make sure they are mounted securely and that the green ground wires are connected.

© 1984 Lucasfilm Ltd. & Atari, Inc. All rights reserved

  • Trademarks of Lucasfilm Ltd. used by Atari, Inc, under license. sec Up

with the same electrical rating.

  • Check for proper line voltage and make sure you are using the correct voltage-selection plug (see Voltage- Plug Selection and Fuses). 4, Calibrate the flight control as follows: a. Move the flight control to the extreme left and right, then up and down. Repeat this procedure three or four times. During this action, the game circuitry monitors the control and calibrates the potentiometers. b. Players also calibrate the control during normal game play, but this may take a few seconds to be optimized. c. If the player-controlled object fails to return to center when the flight control is released, refer to Chapter 2 Self Test and the Vertical Potentiometer and Horizontal Potentiometer subsections in Chapter 3.

Table 1-1 Installation Specifications

Characteristic Specification

265 V-A; 180 W RMS Power Consumption ‘Temperature +5° to +38° C(+37° to +100° F) Humidity Not to exceed 95% relative Line Voltage 100-132 VAC (or 200-264 VAC) Width 25.2 in. (64.1 cm) Depth 36 in. (91.4 cm) Height 68.5 in, (174 cm) Weight 320 Ibs. (145 kg)

Voltage-Plug Selection

and Fuses

The power supply in your game contains six fuses. When you replace a fuse, use the identical type fuse with the same electrical rating (see Figure 1-2). The power supply operates on the line voltage of many countries. The power supply is sold with either one, two, or three voltage-selection plugs. Plug voltages and wire colors are 100 VAC (violet), 120 VAC (yellow), 220 VAC (blue), and 240 VAC (brown). See Figure 1-2 for placement of the voltage-selection plugs. Before plugging in your game, check your line voltage. Next, check the wire color on the voltage-selection plug. Make sure the voltage-selection plug is correct for the line voltage in your location. Now plug the game into a grounded three-wire outlet and set the power on/off switch to the ON position.

Page 12

Set Up

Fuse F3 20A,32V

Fuses F4-F6 4A, 250V

RETURN OF THE JEDI

‘| Voltage Plugs

Fuse F1 7 A, 250 V for US-Built 4A, 250 V for Ireland-Built J3.

See Chapter 5 for complete illustration and parts list.

Figure 1-2 Voltage-Selection Plug and Fuse Locations

Switch Information

Power On/Off Switch The power on/off switch is located at the bottom of the body assembly on the rear of the cabinet (see Figure 1-1).

Utility Panel Switches

The volume control, coin counter(s), self-test switch, and auxiliary coin switch are on the utility panel. The utility panel is located inside the upper coin door (see Figure 1-1). The volume control adjusts the level of sound produced by the game. The coin counter(s) records the number of coins entered into the game. The self-test switch initiates the Self‘Iest Mode. See Figure 5-4 for details of these switches.

Option Settings

RETURN OF THE JEDI offers Easy, Medium, or Hard gameplay difficulty levels; 3, 4, 5, or 6 player lives; and a bonus (or no bonus) every 30,000, 40,000, or 50,000 points. Your game is shipped with options preset at the factory to those shown by the <4 symbols in Tables 1-2 and 1-3. If the manufacturer's recommended settings are not satisfactory for your location, you can change the game's option settings to suit your requirements by using the information provided in Tables 1-2 and 1-3. You must enter ihe SeifTest Mode to change the option settings (see Chapter 2).

Page 13

RETURN OF THE JEDI

= NOTE For complete instructions on how to set the game's options, refer to Chapter 2 Self‘Test.

Table 1-2 Coin & Credit Settings Option Setting Credit Options 1 Coin 2 Coins} 3 Coins 4 Coins

Left Mechanism Value 1 Coin<4}+ 2 Coins

Right Mechanism Value 1 Coin} 4 Coins 5 Coins 6 Coins

Bonus Adder No Bonus Coins Added} Free Play 1 Bonus Coin for 2 Coins 1 Bonus Coin for 3 Coins 2 Bonus Coins for 4 Coins 1 Bonus Coin for 5 Coins 1 Bonus Coin for 4 Coins

Table 1-3, Game Option Settings

Option Setting

No. of Starting Lives Three Lives Four Lives Five Lives<4t Six Lives

Difficulty Levels Easyt Medium Difficult

Bonus Life Awarded Every 30,000 pointst Every 40,000 points Every 50,000 points

Reset High Scores Yes: No~y

“Manufacturer's recommended settings for American games. +Manufacturer’s recommended settings for European games.

Game Play

RETURN OF THE JEDI is a one-player game. The player controls the actions of PRINCESS LELA*, CHEWBACCA’, and LANDO CALRISSIAN* via the flight control. The player's main goal is to destroy the DEATH STAR’. To do this, the player must travel through a tube in the DEATH STAR and fire a torpedo into the central reactor.

RETURN OF THEJEDI has four modes of operation: Attract, Play, High-Score, and Self-Test. Self-Test is a special mode Set Up

for checking the game switches and computer functions, and setting the coinage and game options.

Attract Mode The Attract Mode begins either when the game is plugged in or after exiting from the Play, High-Score, or Self-Test Modes. The Attract Mode ends either when the correct amount of credit is inserted, or when the Self-Test Mode is entered.

When the Attract Mode begins you will see the following credit lines:

RETURN OF THE JEDI © 1984 LUCASFILM AND ATARI ALL RIGHTS RESERVED LUCASFILM TRADEMARKS USED UNDER LICENSE.

Then PRINCESS LEIA appears ON a SPEEDER BIKE‘ traveling through the forest fighting enemy STORMTROOPERS* on SPEEDER BIKES. Then the All-Time JEDI KNIGHTS high-score table is displayed. Various player strategies are demonstrated and instructions are displayed.

Play Mode

RETURN OF THEJEDI picks up the action of the movie at the scene where the rebel forces begin their attack on the Imperial DEATH STAR. LUKE SKY WALKER* and PRINCESS LEIA race toward a pair of speeder bikes. In this first wave, the player controls LEIA, guiding her through a forest toward the EWOK village. She is pursued by Imperial STORMTROOPERS also riding SPEEDER BIKES. She defends herself by either bumping them off their bikes, or shooting them. Meanwhile, the EWOKS* have set up traps to aid LEIA in her flight through the forest of ENDOR. The traps include ropes stretched between trees that the EWOKS pull tight to upend the riders, and logs that the EWOKS push together to crush the SPEEDER BIKES as they pass between them. LEIA can either bump off the sTORMTROOPERS or lead them through the traps. The first vehicle through a trap will escape uninjured, but anyone who follows will be destroyed.

Page 14

Set Up

Once the player leaves LEIA safely at the EWOK village, he moves to another part of the forest. During the second wave, the player controls CHEWBACCA who is maneuvering a SCOUT WALKER to the bunker where HAN SOLO™ is waiting to deactivate the shield protecting the DEATH STAR. CHEW- BACCA must shoot or avoid logs, which roll toward him. At the same time, CHEWBACCA must avoid rocks catapaulted at his SCOUT WALKER. The player can turn the SCOUT WALKER head using the flight control to achieve better aim while firing at the rocks and logs. The split-wave effect occurs during waves two and three. The player controls CHEWBACCA in the SCOUT WALKER, and at the same time, controls LANDO CALRISSIAN as he flies the MILLENNIUM FALCON, At crucial moments, the scene will change from the forest of ENDOR to the skies around the DEATH STAR. While CHEWRACCA is attempting to reach the bunker, LAN- DOCALRISSIAN is flying the MILLENNIUM FALCON toward the DEATH STAR. LANDO must fight off the IMPERIAL ‘T.LE.INTERCEPTORS, IMPERIAL STAR CRUISERS, and shuttles. The player maneuvers the FALCON through this traffic, while trying to shoot as many of the Imperial enemies as possible. AS soon as CHEWBACCA gets to the bunker, HANSOLO blows it up, deactivating the protective shield surrounding the DEATH STAR and clearing the path for the MILLENNIUM FALCON, The MILLENNIUM FALCON must enter the DEATH STAR, travel down a tube toward the reactor, and shoot the central reactor to destroy the DEATH STAR. The FALCON is pursued by IMPERIAL T.L.E. FIGHTERS* while in the tube. LANDO must avoid the pipe walls of the tube and watch out for falling pipes, energy gates, and turrets that shoot at the FALCON. Upon reaching the target, the player must shoot the reactor energy field, then immediately turn around and fly back down the tube. The flight must be rapid because the fireball caused by the explosion pursues the FALCON.

RETURN OF THE JEDI

Hints for Game Play *¢ Donotallow enemies to tail you too long. This is how they can destroy you. Lead enemies to the top of the screen, then drop back quickly so you can destroy them. ° The player must try to be the first through the EwoK traps in the forest of ENDOR . ° By staying in the center of the screen, the player has more maneuverability.

High-Score Mode

RETURN OF THE JEDI has two high-score tables. The first table, Today's REBEL FORCES, lists the top ten scores and the players’ initials for one day. The All-Time JEDI KNIGHTS table lists the overall top ten scores and the players’ initials. In addition, ifa player completes all eight levels of the game, he receives a special bonus of 100,000 points, and the message You have completed your JEDI training, anda star appears beside the player’s initials. The EWOK celebration music plays if the player achieves one of the top 20 scores. The player has 60 seconds to enter his initials using the flight control. By moving the flight control right or left, the player will find his desired letter. Then, by pressing a fire trigger, he can enter a letter. The player does this until he enters three letters, Afterwards, the high-score table displays his newly-entered initials.

Self-Test Mode The Self-Test mode can be entered from all other game modes by sliding the self-test switch down on the utility panel. Self-Test allows for checking of game switches and computer functions, and setting the game and coinage options. See Chapter 2 for complete self-test information.

Page 15

Self-Test

This game will test itselfand provide data to show that the game circuitry and controls are operating properly. Selftest data is presented visually on the video display and audibly through the speakers. No additional equipment is required. We suggest you perform a self-test when you first set up, each time you collect money, change the game options, or suspect game failure.

Chapter 2

Page 16

Self-Test

Self-Test Displays

Seven self-test displays provide a visual check of the following:

  • Random-access memory (RAM), read-only memory (ROM), and associated circuitry operation.
  • Game statistics and options information.
  • Sound-processor and associated circuitry operation. ¢ Flight-control and associated circuitry operation. © Display circuitry operation. ‘When the self-test switch is turned on, the game enters the Self-Test Mode. The following self-test displays are arranged in the sequence in which they occur after the self-test switch (located on the utility panel behind the coin door) is turned on. After Screen 7-Grid Pattern, the sequence starts over with Screen 1-Hardware Test. Turning the selftest switch off at any time during the Self-Test Mode causes the game to return to the Attract Mode.

Screen 1-Hardware Test The Hardware Test screen, as shown in Figures 2-1 and 2-2, provides a visual check of the game RAM, ROM, and their associated circuitry. Screen 1 is divided into RAM and ROM test sections. The condition of the RAM circuitry is displayed in the top half of the screen and, after about a onesecond delay, the condition of the ROM circuitry is displayed in the bottom half of the screen. An error message indicates that the RAM, ROM, or their associated circuitry may be faulty. If the RAM and ROM test passes, the message ZPAGE- ALPHA-COLOR RAM OK and five ROM AT XX: OK

HARDWARE TEST

ZPAGE -ALPHA-COLOR RAM OK

ce

AUX COIN TO CONTINUE

Figure 2-1 RAM/ROM Test Passes RETURN OF THEJEDI

messages will appear as shown in Figure 2-1. The ZPAGE- ALPHA-COLOR RAM OK message indicates that the zero page RAM at location 14B/C, the alphanumerics RAM at location 2R, and the color RAM at locations 12P, 12R, and 12S are operating properly. The ROM AT XX: OK messages indicate that the ROM at the specified locations are operating properly.

HARDWARE TEST

BARR TO ENBABCOR RAM OK

AUX COIN TO CONTINUE

Figure 2-2 RAM/ROM Test Fails

If the RAM test fails, either a colored screen or an error message may appear, A red screen indicates a failure in the zero-page RAM circuitry; a green screen indicates a failure in the alphanumerics RAM circuit; and a magenta screen indicates a failure in the color RAM circuitry. A failure in the remaining RAM circuits tested will display a RAM AT XX BAD message in the top half of the screen, as shown in. Figure 2-2. (Several error messages may mean a faulty address.) Ifthe ROM test fails, a ROM AT XX; BAD message will appear in the bottom half of the screen (for one or more of the five ROM tested) as shown in Figure 2-2. The number that appears after BAD is a diagnostic code (i.c., number 21). Disregard this number. Press the auxiliary coin switch to obtain Screen 2,

Screen 2~Statistics The Statistics screen, as shown in Figure 2-3, provides a visual check of the game statistics. The statistics information is accumulated either from the first time the game was turned on or from the last time the Statistics were reset. (Refer to Resetting the Statistics for the reset procedure.)

Page 17

RETURN OF THE JEDI

STATISTICS

TOTAL GAMES PLAYED: 0002

Qo00K6E 000044 ROE RRcE Same TIME:

BOTH THUMBS CLEAR STATS

PRESSAUXCOINTO CONTINUE

Figure 2-3 Statistics

The following information appears in the Statistics display: ¢ TOTAL GAMES PLAYED shows the total number of free and paid games played. *¢ TOTAL GAME TIME shows the total time, in seconds, of all the games played. ¢ AVERAGE GAME TIME shows the average time, in seconds, of all the games played. Resetting the Statistics. The statistics information can be reset by pressing both flight-control thumb buttons simultaneously. Press the auxiliary coin switch to obtain Screen 3.

Screen 3—Game Options The Game Options screen, as shown in Figure 2-4, provides a visual check of the current option settings. The Op-

GAME OPTIONS

EeeBeetee

IVES: ;EVERY

RESETHIGHSCORES:
PRESSAUXCOINTOCONTINUE

Figure 2-4 Game Options Self-Test

tions display is also used to change the options or reset the top 10 high scores in the high-scorc tablc. Refer to Resetting the High Scores or Changing the Options for the appropriate procedures. Changing the Options. Change the options by moving the flight control up or down to select the option to be changed, which is indicated by a flashing readout. Then press either fire trigger to select the desired option setting. Resetting the High Scores. We suggest that you reset the high-score table after any changes are made to the options that may affect the average game time. The top 10 high scores displayed in the Attract Mode can be reset by pressing the fire trigger. After the readout at the bottom of the screen changes to RESET HIGH SCORES: YES, press the auxiliary coin switch. The readout should change to RESET HIGH SCORES: DONE, which indicates that the top 10 high scores have been reset. (The bottom 10 scores are retained in RAM and are reset when the game power or the self-test switch is turned on.)

Press the auxiliary coin switch to obtain Screen 4.

Screen 4—Sound Processor Test The Sound Processor ‘Test screen is used to verify that the sound-generating circuits are operating properly. When the display appears as shown in Figure 2-5, press the flight

SOUND PROCESSOR TEST

SOUND NUMBER :1C

PRESS AUX COIN TO CONTINUE

Figure 2-5 Sound Processor Test

control right or left thumb buttons to increment or decrement through the 65 available sounds, as indicated by the SOUND NUMBER: XX readout on the screen. (Notall the sounds are used in game play.) Press either fire trigger to start the sound. The voice segments will finish and then

2-3

Page 18

Self-Test

repeat each time the fire trigger is pressed. The remaining sounds will stop immediately and then repeat each time the fire trigger is pressed. If the sound-generating circuit has failed, the message SOUND PROCESSOR BAD willappear near the center of the screen.

Press the auxiliary coin switch to obtain Screen 5.

Screen 5—Control Test The Control Test screen, as shown in Figure 2-6, is used to verify that the game switches are operating properly and that the flight control's vertical and horizontal ranges are within acceptable limits. Perform the following procedure to verify that the game switches and flight-control potentiometers are operating properly.

CONTROL TEST

ESS FIRE Fi cK RESS AUX COIN TO TINUE

Figure 2-6 Control Test

  • Press both thumb buttons simultaneously.
  • Turn the flight control fully clockwise and hold until the horizontal high (HHI) numbers are stable (about one second).
  • Turn the flight control fully counterclockwise and hold until the horizontal low (HLO) numbers are stable (about one second). 4, Tilt the flight contro} to the extreme forward position. and hold until the vertical low (VLO) numbers are stable (about one second).
  • Tilt the flight control to the extreme backward position and hold until the vertical high (VHI) numbers are stable (about one second).
  • Press either fire trigger and check the message under the RANGE column. If the horizontal and vertical ranges are within acceptable limits, tue message OK should appear opposite the hexadecimal numbers for

RETURN OF THE JEDI

both the horizontal and vertical ranges. If the ranges are not within the acceptable limits, the message BAD will appear opposite the unacceptable range(s).

NOTE If the flight control range is not within acceptable limits, the vertical and horizontal potentiometers may be misaligned. Refer to Aligning the Flight Control Potentiometers in Chapter 3 for mechanical alignment procedures.
  • Actuate the right and left coin mechanisms. Note that a message appears indicating that the coin mechanisms are operating properly.
  • One ata time, press the fire triggers and thumb buttons. Note that a message appears, indicating that the fire triggers and thumb buttons are operating properly.

Press the auxiliary coin switch to obtain Screen 6.

Screen 6-Color Bars The Color Bars screen, as shown in Figure 2-7, is used to verify that the video circuits are operating properly and that the display is adjusted for the appropriate colors. The display should contain four horizontal color bars with eight shades in each color bar. Examine the Color Bars display for the following characteristics: © The four color bars (from top to bottom) should be red, green, blue, and gray, with each color bar becoming progressively darker from left to right. The first segment should be barely visible (view the screen with low ambient light). The ninth column (from top to bottom) should be black, white, black, white. These are provided to show

Figure 2-7 Color Bars

Page 19

RETURN OF THE JEDI

contrast with the eighth (darkest) column of the color bars which should show some color. All of the color bars should have the same relative intensity.

¢ All the color bars should have the same relative intensity.

If the display characteristics are not correct, refer to the Display Manual for the adjustment procedure or to determine the possible cause of failure. Press the auxiliary coin switch to obtain Screen 7.

Screen 7-Grid Pattern The Grid Pattern screen, as shown in Figure 2-8, is used to verify that the display size, centering, linearity, and convergence are properly adjusted. Examine the grid pattern for the following characteristics:

  • The four solid boxes in the four corners of the frame around the grid pattern should touch all four corners of the screen.
  • — Grid lines should exhibit no pincushioning or barreling and the lines should be straight within 3.0 mm.
  • Convergence should not exceed 2.0 mm.

If the display characteristics are not within these limits, refer to the Display Manual for the linearity and conver- Self-Test

Figure 2-8 Grid Pattern

gence adjustment procedures or to determine the possible cause of failure.

NOTE Press the auxiliary coin switch after Screen 7— Grid Pattern, to repeat the self-test sequence beginning with Screen 1-Hardware Test.
Page 20

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 21

Maintenance

This chapter includes preventive and corrective maintenance procedures for game components that are subject to the most use. To assure maximum trouble-free operation from this game, Atari recommends that preventive maintenance be performed as described in this chapter. Removal, disassembly, reassembly, and replacement procedures are provided for components that may require corrective maintenance. Appropriate references are provided to Chapter 5 Illustrated Parts Lists, to aid in locating, the parts of this game that are mentioned, but not illustrated, in the maintenance procedures.

To avoid possible electrical shock hazard, unplug the game prior to performing any maintenance.

Chapter 3

Page 22

Maintenance RETURN OF THE JEDI

Preventive Maintenance

Preventive maintenance includes cleaning, lubricating, and tightening hardware. How often preventive maintenance is performed depends upon the game environment and frequency of play. However, for those components listed in Zable 3-1 Preventive-Maintenance Intervals, we recommend that preventive maintenance be performed at the intervals specified.

Preventive-Maintenance Intervals

The preventive-maintenance intervals specified in Table 3-1 are the recommended minimum requirements for the components listed.

Table 3-1 Recommended Preventive- Maintenance Intervals

Component Maintenance Interval

Flight Control Lubricate and tighten hardware at least every three months.

Coin Mechanism Clean at least every three months.

Flight Control Control Panel

Nut/Washer Assy i) To avoid possible electrical shock, turn offand unplug the game before performing any maintenance procedures.

Removing the Control Panel

Perform the following procedure to remove the control panel from the cabinet (see Figure 3-1). 1, Turn the game power off.

  • Unlock and open the coin door on the front of the cabinet.
  • Carefully reach through the coin door opening and release the spring-draw latches located under the control panel on both sides of the cabinet.
  • Lift the front of the control panel and slide it toward you to clear the flight-control assembly from the cabinet.
  • Hook the bracket (located on the underside of the control panel) onto the front edge of the cabinet. Disconnect the flight-control harness connector before moving the control panel to a work surface.

Flight-Control Harness

Spring-Draw Latch

Figure 3-1 Removing the Control Panel and Flight Control

Page 23

RETURN OF THE JEDI Maintenance

Wire & Cable Tie

Potentiometer Tab Key

Red White Black Retainer

Harness Assembly

Handle Assembly Collar

Bumper

Trigger Microswitch Black (Common) Bearing

Shatt

Second Torsion Spring

First Torsion ‘Spring

Labeled Pushbutton

i Sleeve (Ri Microswitch Spring Pin (R) spur dear

Collar

Large

Spur Gear (Normally Open)

Self-Locking Cap Screw

Z Lubrication Points Roll Pin

NOTE The handle-assembly cover is attached with tamper-proof socket screws. A special 42-inch hex-key tool is supplied with each game (Atari part no. 178126-001) for removing the tamperproof socket screws.

Figure 3-2 Handle Assembly

Lubricating the Flight Control

Perform the following procedure to lubricate the flight control. Lubrication can be performed without removing the flight-control assembly from the control panel. See Figures 3-2 and 3-3 for the location of the lubrication points and parts mentioned in the following procedure. Remove the control panel as previously described.

Use the special %,-inch hex-key tool to remove the four tamper-proof socket screws from the handleassembly cover.

Page 24

Maintenance

Retainer First Torsion Spring

Second Torsion Spring Outside Bearing

Anchor Pin

Shaft

(Deep Side)

2) Se

(Shallow Side) Bumper Bearing Spacer Potentiometer

RETURN OF THE JEDI

‘Small Spur Gear

Large Flat Washer

Keying Slot

Ground Clip

Red Anchor Nut

White

Black Z Lubrication Points

Figure 3-3 Steering Assembly

  • Lift the cover from the handle assembly and lubricate the following parts inside the flight control (see the oil can symbols in Figures 3-2 and 3-3). a. Apply two drops of light machine oil (Atari part no. 107013-001) to the potentiometer shafts and to the four main shaft bearings. b. Brush a light film of Nyogel 779 lubricant (Atari part no. 178027-001) over the outside of the four torsion springs and on the teeth of the two small spur gears.

Tightening the Flight- Control Hardware Use the appropriate hex driver and combination wrenches to tighten all the flight control screws and mounting nuts (see Figures 3-1, 3-2, and 3-3).

3-4

Cleaning the Coin Mechanism

Use a soft-bristled brush to remove loose dust or foreign material from the coin mechanism, A toothbrush may be used to remove any stubborn build-up of residue in the coin path. After cleaning the coin mechanism, blow out all of the dust with compressed air.

Cleaning the Cabinet and

Display Shield

The game cabinet and display shield may be cleaned with any non-abrasive household cleaner. Compressed air is recommended for cleaning dust from the interior of the cabinet.

Page 25

RETURN OF THE JEDI

Maintenance

Corrective Maintenance

Corrective maintenance consists of removal, disassembly, reassembly, and replacement of game components. The following procedures are provided for components that may require corrective maintenance.

Flight Control

The following corrective maintenance procedures apply to the flight control. The flight control consists of a handle assembly and a steering assembly. The handle assembly controls the vertical motion, and the steering assembly controls the horizontal motion of the graphics on the display. After any corrective maintenance is performed, the flight control should be recalibrated as described in this chapter under Calibrating the Flight Control.

Removing the Flight Control

NOTE The handle assembly can be disassembled with the flight control attached to the control panel. However, for convenience and to avoid damaging the control panel, we recommend that the flight control be removed from the game before any corrective maintenance or repair is performed,

Perform the following procedure to remove the flight control from the control panel (see Figure 3-1). 1, Remove the control panel as previously described.

  • Disconnect the flight-control harness assembly.
  • Usea %.-inch combination wrench to remove the four locknuts and washers that secure the flight control to the control panel. 4, Carefully remove the flight control from the control panel.
  • To reinstall the flight control, guide the flight control back into the control panel.
  • Attach the four locknuts and washers that mount the flight control to the control panel.
  • Reconnect the flight-control harness assembly.
  • Reinstall the control panel.

Removing the Handles Perform the following procedure to remove the handles from the handle assembly (see Figure 3-2).

  • Usea %,-inch hex driver to remove the four cap screws that hold the covers onto the handles. Be careful when removing the covers because the trigger and pushbutton springs can fall off the handles.
  • Unsolder the three harness wires from the trigger and pushbutton microswitches inside each handle and pull the harness out of the shaft.
  • Usea %,-inch hex driver to remove the four cap screws that hold the handles onto the shaft. 4, Usea ¥,-inch punch to drive the roll pin (located between the two cap screws) into the hollow of the shaft. Remove the roll pin from the shaft.
  • Gently slide the handles from the shaft. To reinstall the handles, solder the three harness wires from the trigger and pushbutton microswitches,
  • Reinstall the roll pin.
  • Replace the trigger, pushbutton springs, retaining ring, bushing, and button. Reinstall the cap screws that hold the covers onto the handles.
  • Reinstall the four cap screws that secure the handles to the shaft.

Disassembling the Handle Assembly

Perform the following procedure to disassemble the handle assembly (see Figure 3-2).

NOTE Itis not necessary to remove the handle assembly from the steering assembly to perform the following disassembly procedure. However, if you prefer, refer to steps 1 through 4 under Disassembling the Steering Assembly for the procedure that describes how to separate the two assemblies.
  • Use the special 42-inch hex-key tool to remove the four tamper-proof cap screws from the handle-assembly cover.
  • Remove the handles as previously described.
  • Gently pull the harness wires out of the hollow shaft. 4, Usea %,-inch hex driver to remove the cap screw and washer that hold the spring pin to the handle-assembly shaft.
  • Slide the spring-handle pin out of the shaft. Use a %4-inch hex driver to loosen the cap screw that holds the large spur gear to the shaft.
  • Slide the large (60-tooth) spur gear down the shaft to expose the shaft retainer on the right side.

3-5

Page 26

Maintenance

Shield your face and eyes when prying out the retainers because they can fly loose at a high speed. Cover the retainers with a piece of cloth to trap the retainers.

  • Use aright-angle slotted screwdriver to pry the retainer from the shaft.
  • Repeat step 8 to remove the retainer on the left side of the shaft.
  • Gently slide the shaft from the housing. ll. Usea %,-inch hex driver to loosen the cap screw that holds the small (14-tooth) spur gear to the potentiometer shaft. 12, Usea %-inch combination wrench to remove the nut and washer that hold the potentiometer to the mounting bracket.
  • Slide the potentiometer from the bracket. Be careful not to lose the small spur gear, nut, and washer. 14, Use a %,-inch hex-driver and %-inch combination wrench to remove the two bumpers from the frame.
  • Reassemble the handle assembly as described in the following procedure.

Reassembling the Handle Assembly

Perform the following procedure to reassemble the handle assembly (see Figure 3-2).

  • Use a %-inch hex driver and %-inch combination wrench to install the two bumpers on the frame.
  • Insert the large (60-tooth) spur gear with the collar facing away from the bearing. Align and hold the gear in line with the bearing hole. (The gear fits through the slot on the right front of the frame.)
  • Slide the shaft through the right bearing and the spur gear. Do not insert the shaft past the outside edge of the spur-gear collar. 4, Apply a heavy film of Nyogel 779 lubricant (Atari part no. 178027-001) to the inside of the torsion spring.
  • Hook the straight end of the first torsion spring through the hole closest to the right side of the frame.
  • Hold the first torsion spring in line with the shaft so that the looped end of the spring is facing away from the spur gear.
  • Slide the shaft just through the first torsion spring.
  • Hook the straight end of the second torsion spring through the hole closest to the left bearing.
  • Hold the second torsion spring in line with the shaft so that the looped end of the spring is facing the first torsion spring.

3-6 10.

ll.

12.

13.

14,

15.

16.

17.

18.

19.

20.

21.

22.

23,

24,

25.

26.

27.

28.

RETURN OF THE JEDI

Slide the shaft through the second torsion spring and the left bearing. Position the shaft so that the retainer grooves are just inside the bearings. Install the two retainers into the shaft grooves. Turn the shaft so that the two large holes and the smaller centered hole are facing upward. Tocate the hole in the spring pin. Insert the end of the spring pin that is closest to the hole through the slot in the frame and through the hole in the shaft. Make sure both torsion spring looped ends are wrapped over the spring pin. Position the spring pin so that the hole in the pin is aligned with the hole in the shaft. Use a %,-inch hex driver to tighten the cap screw and washer that secure the pin to the shaft. Align the cap screw in the spur-gear collar with the threaded hole in the shaft and use a %,-inch hex driver to tighten the cap screw. Insert the potentiometer shaft through the hole in the mounting bracket. Before fully inserting the shaft through the bracket, place the washer, nut, and small (14-tooth) spur gear (with the collar facing inward) onto the shaft. Align the potentiometer so that the tab key is inserted into the keying slot. Use a ¥2-inch combination wrench to loosely secure the nut on the potentiometer shaft. Turn the potentiometer shaft so that the flat side faces the center wire terminal. Align the cap screw on the small (14-tooth) spur gear with the flat side of the shaft. Use a %,-inch hex driver to tighten the cap screw. Slide the potentiometer forward so that the teeth on the two spur gears are tightly meshed; then slide the potentiometer and small (14-tooth) spur gear about 4, inch away from the large spur gear. Use a %-inch combination wrench to tighten the potentiometer to the mounting bracket. Install the harness assembly as described later in this chapter, Install the handles in the reverse order of the removal procedure. Do not install the handle covers until the harness is installed and the proper wires are soldered. to the trigger and pushbutton microswitches. Check the vertical potentiometer alignment as described in this chapter under Aligning the Flight- Control Potentiometers. Install the handle-assembly cover and use a 42-inch hex-key tool to tighten the four tamper-proof socket screws that secure the cover to the handle assembly.

Page 27

RETURN OF THE JEDI

Maintenance

Disassembling the Steering Assembly

Perform the following procedure to disassemble the steering assembly (see Figures 3-2 and 3-3), i

10. Remove the handle covers as previously described in this chapter. Be careful when opening the handles because the pushbutton and trigger springs may fall out. Unsolder the three harness wires from the vertical potentiometer and the handle pushbutton and trigger microswitches.

Use a %2-inch hex driver to remove the three cap screws and lock washers that hold the steeringassembly shaft to the handle-assembly frame. Gently pull the two assemblies apart. Make sure the harness wires are free to slide out of the handle-assembly shaft. Use a ¥,-inch wrench to remove the anchor nut on the end of the anchor pin. (The anchor nut faces the open end of the frame.) Slide the anchor pin from the shaft. Grasp the large (60-tooth) spur gear and slide the shaft from the frame. The bearing spacer and torsion springs will fall free. Usea %4-inch hex driver to remove the cap screws that hold the large spur gear to the steering shaft and the small spur gear to the potentiometer shaft. Use ¥% -inch combination wrench to remove the nut and washer that hold the potentiometer to the frame. Unsolder the three harness wires from the potentiometer terminals,

WARNING Shield your face and eyes when prying the retainer from the shaft because the retainer can fly loose at a high speed. Cover the retainer with a piece of material that will trap the retainer.

ll. Use aslotted screwdriver to remove the retainer from the shaft.

  • Use a %,-inch hex driver and %-inch combination wrench to remove the two bumpers from the frame.
  • Reassemble the steering assembly as described in the following procedure.

Reassembling the Steering Assembly Perform the following procedure to reassemble the steering assembly (see Figure 3-3).

  • Use a %2-inch hex driver and %-inch combination wrench to install the two bumpers to the frame.
  • Snap the retainer into the groove of the shaft and slide the large, flat washer down the long end of the shaft and against the retainer.
  • Apply a heavy film of Nyogel 779 lubricant (Atari part no. 178027-001) to the inside of the torsion springs.
  • Hook the straight end of the first torsion spring through the hole closest to the back of the frame. Slide the shaft through the outside bearing and the first torsion spring.
Page 28

Maintenance

10.

uM.

12.

13.

15.

3-8 Hook the second torsion spring through the hole on the opposite side and closest to the front of the frame. Slide the shaft through the second spring and the opposite bearing. ‘Turn the shaft so that the threaded hole at the retainer end of the shaft faces up toward the open side of the frame. (The hole through the center of the shaft will then be perpendicular to the open side of the frame.) Use a {.-inch combination wrench to install the anchor pin and nut through the hole in the center of the shaft. Make sure the looped ends of the torsion spring are wrapped under the anchor pin and nut. Slide the large (60-tooth) spur gear onto the shaft with the collar facing outward. Align the cap screw in the spur-gear collar with the threaded hole in the shaft, and use a %,-inch hex driver to tighten the cap screw. Insert the potentiometer shaft through the hole in the frame and align the potentiometer so that the tab key is inserted into the keying slot. Install the washer and nut on the potentiometer shaft, but do not tighten. ‘Yurn the potentiometer shaft so that the flat side faces the center wire terminal. Align the cap screw on the small (28-tooth) spur gear with the flat side of the shaft and slide the small spur gear (with the collar facing inward) onto the potentiometer shaft.

Position the spur gear so that its teeth mesh with those of the large spur gear and use a %,-inch hex driver to tighten the cap screw. Slide the potentiometer forward so that the teeth on the two spur gears are tightly meshed; then slide the RETURN OF THEJEDI

potentiometer and small spur gear about %4-inch away from the large spur gear.

  • Use a %-inch combination wrench to tighten the potentiometer to the frame.
  • Slide the bearing spacer over the shaft at the end opposite the spur gears. Check to make sure that the deep side of the bearing spacer sits over the head of the bronze flange bearing in the steering-assembly frame.
  • Ifnecessary, lubricate the steering assembly as previously described in this chapter.
NOTE The remaining steps describe the procedure for attaching the steering assembly to the handle assembly.
  • Insert the steering-assembly shaft into the collar on the handle-assembly frame.
  • Align the three holes in the steering-assembly shaft with the three holes in the handle-assembly collar. 21, Use a %»-inch hex driver to tighten the three cap screws and lock washers. Be sure the screws are tight.
  • Install the harness assembly as described in the following procedure. 23, Check the horizontal potentiometer alignment as described under Aligning the Flight-Control Potentiometers,

Installing the Harness Assembly

Perform the following procedure to install the harness assembly to the flight control (see Figures 3-2 and 3-3).

Page 29

RETURN OF THE JEDI

  • If necessary, remove the handle covers as described under Removing the Handles.
  • Guide the harness wires into the spur-gear end of the hollow steering-assembly shaft. The wires for the steering, horizontal potentiometer, and grounding clip should remain outside of the shaft.
  • Route and solder the wires to the potentiometers and microswitches. Note that the wire bundle that goes to the right handle is identified with a labeled sleeve (R).
  • Install the wire ties and the ground clip. Make sure the wires do not interfere with the gears when the flightcontrol assembly is mounted.

Aligning the Flight- Control Potentiometers The following procedures describe the method for checking and aligning the vertical and horizontal flight-control potentiometers to ensure that the player-controlled object on the display is centered when the flight control is released.

Preliminary Procedure Perform the following procedure to determine if the vertical and/or horizontal potentiometers are misaligned.

  • Turn off the game power.
  • Set the self-test switch to the on position.
  • Turn on the game power.

Perform the Control Test display procedure for checking the flight control range as described in Chapter 2. If the self-test display indicates that the flight-control vertical or horizontal range is out of tolerance, perform the appropriate procedure as follows.

Vertical Potentiometer Perform the following procedure to align the flight-control vertical potentiometer (see Figure 3-2).

  • Turn off the game power.
  • If necessary, remove the flight-control handleassembly cover with the special 4,.-inch hex-key tool to gain access to the vertical-motion potentiometer.
  • With the flight control centered (no tension on the return springs), check that the set screw on the potentiometer spur gear is facing the center (white) wire terminal. If it is not, use a %-inch combination wrench and loosen the potentiometer mounting nut. Slide the potentiometer sideways in the mounting bracket until the gears disengage. Turn on the game power.
  • Turn the small spur gear until the Control Test display (obtained in the Preliminary Procedure) indicates that the vertical potentiometer is within the allowable limits. Maintenance
  • Gently slide the potentiometer forward so that the spur-gear teeth are tightly meshed. (If necessary, slightly move the large gear to align the gear teeth—do not turn the potentiometer shaft.) Recheck the Control Test display limits.
  • Pull the potentiometer and small spur gear about 4 inch away from the large spur gear. Use a %-inch combination wrench to tighten the potentiometer to the mounting bracket.
  • Install the handle-assembly cover by using the special %2-inch hex-key tool to tighten the tamper-proof socket screws.

Horizontal Potentiometer Perform the following procedure to align the horizontal potentiometer (see Figure 3-3).

  • Turn off the game power.
  • Remove the control panel as previously described.
  • With the flight control centered (no tension on the springs), check that the set screw on the potentiometer spur gear is facing the center (white) wire terminal. Ifnot, use a 44-inch hex driver and loosen the set screw on the potentiometer spur gear. Slide the spur gear off of the potentiometer shaft. 4, Turn on the game power.
  • Turn the potentiometer shaft until the Control Test display (obtained in the Preliminary Procedure) indicates that the horizontal range is within the allowable limits.
  • Slide the spur gear onto the potentiometer with the set screw centered over the flat side of the shaft. Align the gear teeth so they mesh with the large spur gear. (If necessary, the large spur gear can be turned slightly— do not turn the potentiometer shaft.)
  • Use the %,4-inch hex driver and tighten the spur-gear set screw. Recheck the Control Test display to make certain the horizontal range is still within the allowable limits.

Calibrating the Flight Control

The flight control is self-calibrating. The game circuitry monitors the control and calibrates the potentiometers. Calibrate the flight control after any corrective maintenance is performed by moving the flight control to the extreme right, left, up, and down positions. This should be repeated several times. Players also calibrate the control during normal game play, but it may take several seconds of game play to be optimized. If the player-controlled object fails to return to center screen when the flight control is released, check the flight control vertical and horizontal range as previously described in this chapter.

Page 30

Maintenance

Removing the Display Shield

and Bezel

Perform the following procedure to remove the display shield and bezel from the cabinet (see Figure 3-4).

  • Usea Phillips-head screwdriver to remove the display access panel from the rear of the game cabinet.
  • From the front of the cabinet, use a %-inch Allen wrench to remove the upper retainer of the attraction panel. Save the hardware for reassembly.
  • Slide the attraction panel and the semi-rigid film (behind the panel) up and out of the left and right caps.
NOTE Moldings are firmly fitted on each side of the attraction panel and on each side of the display shield. These moldings should stay on the attraction panel and display shield.
  • Remove the H-shaped retainer between the attraction panel and the display shield.
  • Slide the display shield up and out of the right and left caps. If necessary, loosen the lower retainer to break the foam tape seal on the bottom of the display shield.
  • Carefully remove the display bezel.

Removing the Display

Perform the following procedure to remove the display from the cabinet (see Figure 3-4).

WARNING High Voltage This display contains lethal high voltages. To avoid injury, do not attempt to service this display until you observe all precautions necessary for working on high-voltage equipment. X-Radiation This display has been designed to minimize Xradiation. However, to avoid possible exposure to soft X-radiation, NEVER modify the highvoltage circuitry. Implosion Hazard The cathode-ray tube may implode if struck or dropped. Shattered glass may cause injury within a 6-foot radius. Use care when handling the display.

RETURN OF THE JEDI

Turn the game off and wait approximately two minutes. Unplug the game. Remove the display shield and bezel as previously described. Use a Phillips-head screwdriver to remove the four screws securing the right and left caps to the cabinet. Discharge the high-voltage from the cathode-ray tube (CRT) before proceeding. The display assembly contains a circuit for discharging the high voltage to ground when power is removed. However, to make certain, always discharge the display as follows. a. Attach one end ofa large, well-insulated, 18-gauge jumper wire to ground. b. Momentarily touch the free end of the grounded jumper to the CRT anode by sliding it under the anode cap. c. Wait two minutes and repeat part b. From the back of the cabinet, open the rear access panel. Unplug the display-harness connectors and disconnect the ground wire. From the front of the cabinet, remove the hardware that secures the video display to the cabinet. Save this hardware for reassembly. Carefully remove the display through the front of the cabinet. Place it on a soft mat in a protected location.

NOTE Whenever the video display is replaced readjust the brightness, purity, and convergence as described in the display manual.
Page 31

RETURN OF THE JEDI Maintenance

Upper Retainer

Attraction Panel Assy Molding

H-Shaped Retainer Light-Panel Assy

Video Display Nut/Washer Assy

Mounting Panel

Harness

Speaker Grille

Display Shield

Molding

Right Cap

Figure 3-4 Removing the Video Display and Light-Panel Assembly

Page 32

Maintenance

Removing the Light-

Panel Assembly

Perform the following procedure to remove the light-panel assembly from the cabinet (see Figure 3-4).

  • Remove the display shield and bezel as previously described,
  • Use a Phillips-head screwdriver to remove the four screws securing the right and left caps to the cabinet.
  • Disconnect the harness from the light-panel assembly. Use a Phillips-head screwdriver to remove the two screws securing the cleat to the top of the displaymounting frame.
  • Slide the light-panel assembly out of the front of the cabinet.

Removing the Speakers Perform the following procedure to remove the speakers from the cabinet (see Figure 3-4),

3-12

RETURN OF THE JEDI

  • Remove the control panel as previously described.
  • Use a Phillips-head screwdriver to remove the four screws securing the speaker grille to the cabinet.
  • From inside the control-panel opening, use a Phillipshead screwdriver to remove the two screws securing the speaker retaining bracket to the cabinet.
CAUTION Do not touch the speaker cones when handling the speakers. The cone material is fragile and can be easily damaged.

4, Slide the speaker and mounting board sideways through the slot in the cabinet.

  • Disconnect the speaker-harness connector. Use a Phillips-head screwdriver to remove the four screws securing the speaker to the mounting board.
Page 33

Troubleshooting

This chapter contains a discussion of troubleshooting aids and techniques to assist the service technician when a trouble is suspected in this game. Most troubles can be located quickly by following the information in this chapter. However, if problems persist, contact your nearest Atari Customer Service office listed on the inside front cover of this manual for assistance. A thorough knowledge of game operation is desirable for effective troubleshooting. In addition to the operation and service information in the Schematic Package Supplement included with this manual, refer to The Book, A Guide To Electronic Game Operation and Servicing. This publication is available from Atari, Inc., and has more information on coin-operated electronic games.

NOTE We recommend that troubleshooting and repair procedures be performed by a qualified electronic technician.

Chapter 4

Page 34

Troubleshooting

Troubleshooting Aids

Troubleshooting aids are provided throughout this manual and the Schematic Package Supplement. The following information is intended to acquaint the service technician. with portions of these documents that contain useful troubleshooting and repair information.

Assembly and Component Locations The parts lists in Chapter 5 illustrate the locations of assemblies and components. Printed-circuit board (PCB) illustrations aid in rapidly locating components shown on the corresponding schematic diagram(s).

Diagrams The Schematic Package Supplement included with this game contains schematic diagrams with component locations, active component type numbers, and electrical values,

Troubleshooting Procedures

Refer to the following section, Troubleshooting Techniques, for a suggested troubleshooting sequence to aid in. locating defective components.

Troubleshooting Techniques

To avoid electrical shock, turn off the game power before attempting to troubleshoot this game.

The following troubleshooting steps are arranged ina sequence recommended for locating a defective component. The procedure begins with a check of the simple trouble possibilities and progresses to more extensive procedures for localizing the problem to an assembly or major circuit, and then to a defective component.

Check Switch Settings Incorrect switch settings can sometimes indicate a problem that does not exist. Refer to Chapter 1 to verify that the game has been installed properly and the option settings are correct. Refer to Chapter 2 for instructions on how to set the option settings. Check for proper operation in all game-play modes.

Check Fuses Check for open fuses. Refer to Chapter 5 and the Display Manual for the location and rating of each fuse used in this game. Make sure that replacemcnt fuscs are the proper type and rating.

4-2

RETURN OF THE JEDI

Check Power-Supply Voltages Improper operation of all circuits usually indicates a power supply problem. Be sure that the proper line voltage is available to the power supply. Check for correct voltages.

Localize Trouble Determine the trouble symptom. Use the wiring diagrams in the Schematic Package Supplement to determine which assemblies or major circuits could cause the trouble. Perform the self-test procedure provided in Chapter 2.

Visual Check Visually check for obvious problems in the portion of the game where the trouble is suspected. For example, check for loose or defective solder connections, integrated circuits loose in their sockets, loose cable connections, broken wires, and damaged components.

Check Individual Components Check soldered-in passive components (e.g., resistors, capacitors, diodes) by disconnecting one end to isolate the measurement from the effects of the surrounding circuitry. Often, direct substitution is the most practical way to determine if a component is faulty. However, eliminate the possibility of some other circuit problem that could damage the substitute component.

Repair the Assembly

CAUTION Soldered-in transistors and integrated circuits are difficult to remove without damaging the printed-circuit board or component. Refer to the information in this chapter pertaining to soldering and replacing integrated circuits and transistors.

Repair or replace the defective part. Refer to Chapter 3 and information in this chapter for special removal and replacement procedures, Check for proper operation of the repaired circuit.

Soldering Techniques

Observe the following recommendations when removing, or replacing components soldered to a PCB. Poor soldering practices can damage a PCB or heat-sensitive electrical components. Choosing the proper soldering iron is essential before attempting to remove or replace soldered-in components. Excessive heat is a common cause of damage toa component or PCB, However, transient voltages from solder guns or improperly grounded soldering irons can also damage certain voltage-sensitive semiconductor devices. Refer to

Page 35

RETURN OF THE JEDI

Troubleshooting Static-Sensitive Devices for more specific information. A 15- to 27-watt pencil-tip soldering iron is recommended to avoid separating the etched circuit wiring from the board material and to avoid damaging active components. A temperature-controlled soldering station rated at 700° F with a fine cone ora very fine chisel tip can also be used.

CAUTION Solder guns are not recommended for removing or replacing soldered-in components ona printed-circuit board. The added possibility for overheating and the large transient voltage induced by the solder gun could cause damage to heat- or voltage-sensitive devices.

The following additional equipment is recommended for removing and replacing soldered-in components. ¢ Solder Sucker—Hand-operated vacuum tool used to remove liquified solder from the PCB. Top-of-the-line Soldapullt® brand is recommended.

  • Solder Wick—Resin-soaked copper braid used for removing excess solder from the lead connections on the PCB. See Removing Integrated Circuits for precautions relating to the use ofa solder wick on a multilayer PCB with plated-through holes. ¢ Flux Remover—Non-corrosive chemical used to clean foreign material from the PCB before soldering, and to remove any flux residue where components have been replaced. Flux remover is also used to clean any foreign material from the PCB during preventive maintenance. Isopropyl alcohol is also recommended as a cleaner. ¢ Acid Brush—Small stiff-bristled paint or toothbrush used with flux remover to clean flux and other foreign material from the PCB.

Removing Integrated Circuits The easiest and safest method for removing soldered-in integrated circuits (IC) from a PCB is to cut off each pin as close to the IC case as possible with a tip dyke (diagonal cutter) as shown in Figure 4-1.

Diagonal Cutter

Figure 4-1 Removing IC (Cut Pin Method) Troubleshooting

Use the proper soldering iron as previously described under Soldering Techniques. Then, to avoid excessive heat buildup in one area of the PCB, apply heat directly to each pin in arandom order. Remove the loosened pin with the tip of the soldering iron or with needle-nose pliers as shown in Figure 4-2. Allow a moment for the PCB to cool before proceeding to the next pin. Apply just enough heat to remove any stubborn pins.

Needle-Nose Pliers

Soldering Iron

Figure 4-2 Removing IC Pins

For a multi-layer PCB with plated-through holes, use a solder sucker to remove the remaining solder from inside each hole as shown in Figure 4-3. If possible, suck the solder from the opposite side of the PCB from where the heat is applied, Use a solder wick to remove excess solder from around the lead connection pads on the top and/or bottom surface of the PCB as shown in Figure 4-4,

CAUTION Do not use a solder wick to remove solder from inside plated-through holes. The heat required for the solder wick to remove the solder from inside the hole could damage the PCB.

Troubleshooting Static- Sensitive Devices

Certain precautions must be taken when working with static-sensitive devices, e.g., microprocessors, field-effect transistors (FET), complementary metal-oxide semiconductors (CMOS), and other large-scale integration (LSI) devices that use metal-oxide semiconductor (MOS) technology. Static charge buildup in a person's body or leakage from an improperly grounded soldering iron can cause static-sensitive device failure.

Page 36

Troubleshooting

Solder Sucker

Preferred Method Soldering Iron

RETURN OF THE JEDI

Solder Sucker

Soldering Iron

Alternate Method

Figure 4-3, Removing Solder from Plated-Through Holes

Before handling a static-sensitive device or a PCB with such devices attached to it, ground any static voltage that may have accumulated in your body by touching an object that has been earth grounded. A bare wire wrapped around your wrist and attached to an earth ground is effective when working extensively with static-sensitive devices. When soldering on a Static-sensitive device, use asoldering iron with a properly grounded three-wire cord, (Refer to Soldering Techniques for a discussion of recommended soldering irons and procedures.) A static-sensitive device may appear defective due to leakage on a PCB, Observe the precautions for grounding

Soldering Iron static voltages described in the preceding paragraph and clean both sides of the PCB with flux remover or an eraser before replacing what may be a good static-sensitive device. For discrete FET devices, clean thoroughly between the gate, drain, and source leads. Static-sensitive devices may be packaged in conductive foam or have a protective shorting wire attached to the pins. Remove the conductive foam just prior to inserting the device in its socket or soldering to a PCB. Remove the shorting wire only after the device is inserted in its socket or after all the leads are soldered in place.

Solder Wick

Figure 4-4 Removing Solder from Lead Connection Pads

4-4

Page 37

IlNustrated Parts Lists

This chapter provides information you need to order parts for your game. Common hardware (screws, nuts, washers, etc.) has been deleted from most of the parts lists. However, a parts list is included for the hardware to mount the printed-circuit boards (PCBs) to the cabinet. The PCB parts lists are arranged in alphabetical order by component. Each component subsection is arranged alphanumerically by reference designator. Other parts lists are arranged alphanumerically by Atari part number. In these parts lists, all A-prefix numbers appear first. Following these are numbers in sequence evaluated up to the hyphen, namely 00- through 99-, then 000598- through approximately 201000-. When ordering parts, please give the part number, part name, number of this manual, and serial number of your game. This will aid in filling your order rapidly and correctly. We hope the results will be less downtime and more profit from your game, Atari Customer Service numbers are listed on the inside front cover of this manual.

Chapter 5

Page 38

Iitustrated Parts Lists RETURN OF THE JEDI

042679-01 Attraction Film wiGraphics 041249-01 006008-05 Upper Retainer Molding

042658-01 Onieerg Video Display Assy i See Display Manual Attraction Shield. " Fluorescent Tube Assy & Figure 3-4 See Figure 5-4 041250-01

042680-02 041256-1715 Retainer H Shaped Retainer

7 Se Decal

‘A042674-01 Speaker & Panel Assy 042655-01 Left Cap

042660-xx Instruction Decal

006008-04 Molding

042657-01 Video Display Shield ee

! 042656-01 Flight-Control Assy ee Speaker Grille See Figure 5-3

Control Panel Assy See Figure 5-2

042655-02 Right Cap

178013-001 Latch

Coin Doors See Figures 5-7 & 5-8

. 178034-024 038091-01 Molding Molded Coin Box

041649-02 fs ih Shae us Right Corner Molding Enclosure— Utility Panel Assy 041649-01 038781-01 See Figure 5-6 Left Corner Molding Coin Box @ See parts list for Ireland part number. Enclosure—Eire

Figure 5-1 Cabinet-Mounted Assemblies A042641-xx A

Page 39

RETURN OF THE JEDI Illustrated Parts Lists

A042646-01 Cabinet Assembly Game Documentation— A042648-01 See following parts list Head Assembly Video Display Assy See Display Manual 042680-02 I Right Decal & Figure 3-4

042669-01 Access Panel

034536-02 Foam Pad 178034-024 EMolding

A042675-01 aan seeker Left Speaker Housing Assy Housing Assy

042661-02 Right Decal Game PCBs See Figures §-9-5-1

034536-02 Foam Pad mas A040735-01

Main Harness Assy

lator/Audio II Regulator/Audio Il PCB A038881-01 See Figure 5.9 and 5.12 Lock

A042647-01 Body Assembly

A040736-01 a Power Harness Assy S ao

Power Supply Assy See Figure 5-5

041630-02 Access Panel A041606-01 Pedestal Assembly

037332-01 Ventilation Grille

78-3201 Adjustable Glide A037453-01 A040699-xx Power Cord op0es2 Power On/Off

‘Switch w/Harness On/Off Switch Cover 042662-01 Pedestal Panel

Figure 5-1 Cabinet-Mounted Assemblies, continued A042641-xx A

5-3

Page 40

Illustrated Parts Lists RETURN OF THE JEDI

Cabinet-Mounted Assemblies Parts List

Part No. Description

US-Built Cabinet A040699-01 Power On/Off Switch with Harness Assembly 038870-01 Coin Box Enclosure

Ireland-Built Cabinet A039270-01 Shorting Plug Assembly (not shown) A040699-04 Power On/Off Switch and Harness Assembly 139016-1007 Hantarex 19-Inch Color Raster Display (Acceptable substitute for part no. 139003-1004) 038781-01 Coin Box Enclosure

US- and Ireland-Built Cabinet A037453-01 Strain-Relief Power Cord A038881-01 Lock Assembly for Body Access Panel A040735-01 Main Harness Assembly A040736-01 Power Harness Assembly A042646-01 Cabinet Assembly—includes: A041606-01 Pedestal Assembly A042647-01 Body Assembly A042648-01 Head Assembly A042674-01 Speaker and Panel Assembly—includes: A040738-01 Speaker Harness Assembly 042673-01 Speaker Panel 148001-013 6 x 9-Inch, 4 Ohm, 6-Ounce Shielded Speaker 176015-110 #10 x %-Inch Cross-Recessed Pan-Head Screw

A042675-02 Right Speaker Housing Assembly A042675-01 Left Speaker Housing Assembly 78-3201 Adjustable Glide 78-6900402 Y%-Inch Wide x %-Inch Thick Foam Tape (used between video display and control panel, and attraction shield and retainer—not shown)

The following six items are technical information supplements to this game: TM-160 Electrohome 19-Inch Color Raster Display Manual (use with part no. 92-049) TM-210 Disco 19-Inch Color Raster Display Manual (use with part no. 139003-1006) T™M-220 Matsushita 19-Inch Color Raster Display Manual (use with part no. 139003-1004) TM-227 RETURN OF THE JEDI Operators Manual SP-227, RETURN OF THE JEDI Schematic Package Supplement ST-227 RETURN OF THE JEDI Chart with Self-Test Procedures and Option Settings 006008-04 Plastic Molding for Display Shield 006008-05 Side Plastic Molding for Attraction Panel 009992-01 On/Off Switch Cover 034536-02 ¥z-Inch Foam Pad (used on Regulator/Audio 11 PCB and Main PCB)

037332-01 Ventilation Grille (one not shown—located on top of head assembly) 038091-01 Molded Coin Box 041249-01 Upper Retainer for Attraction Panel 041250-01 Retainer (located between video display and contro! panel)

041256-1715 H-Shaped Retainer 041261-01 Video Display Bezel 041630-02 Access Panel for Body Assembly 041649-01 Left Corner Molding

5-4 (continued on next page)

Page 41

RETURN OF THE JEDI Mlustrated Parts Lists

Cabinet-Mounted Assemblies Parts List, continued

Part No. Description

041649-02 Right Corner Molding, 042653-01 Retaining Bracket 042655-01 Cap for Left Side of Head Assembly 042655-02 Cap for Right Side of Head Assembly 042656-01 Speaker Grille 04265701 Video Display Shield 042658-01 Glass Attraction Shield 042660-01 English Instruction Decal 042660-02 German Instruction Decal 042661-01 Decal for Left Speaker Housing (not shown) 042661-02 Decal for Right Speaker Housing 042662-01 Pedestal Panel 042669-01 Access Panel for Head Assembly 042679-01 Attraction Film with Graphics 042680-01 Decal for Left Side of Head Assembly (not shown) 042680-02 Decal for Right Side of Head Assembly 176015-112 #10 x %-Inch Cross-Recessed Pan-Head Screw (for mounting speakers) 176020-212 #8 x ¥%4-Inch Black Cross-Recessed Screw (for mounting speaker grille to housing) 178013-001 Spring-Draw Latch 178034-024 %4-Inch TMolding (21 inches required on front of pedestal base; 168 inches required on side panels of head assembly; 104 inches required on side panels of body assembly; 94 inches required on front panel of body assembly)

Page 42

Illustrated Parts Lists RETURN OF THE JEDI

Flight Control Assy 042678-01 See Figure 5-3 oateie-oi Flight-Control Decal 3 Spacer 041561-01 Control Panel

75-5112B Carriage Bolt

041615-01 Plate

042676-01 Left Decal

75-9951 NuvWasher Assy

042677-01 Right Decal

75-99515 NuvWasher Assy

Figure 5-2 Control Panel Assembly A042645-xx A Parts List

Part No. Description

041561-01 Formed Control Panel 041615-01 Control-Panel Plate 041616-01 Flight-Control Spacer 042676-01 Left Control Panel Decal

042677-01 Right Control Panel Decal 042678-01 Flight-Control Decal 75-5112B #10-24 x %4-Inch Black Carriage Bolt 75-9951 #10-24 Nut/Washer Assembly 75-99515 #%-20 Nut/Washer Assembly

Page 43

RETURN OF THE JEDI Illustrated Parts Lists

176025-3604 Tamper-Proof Cap Screw

040248-01 Cover

178012-001 Retai Ri gen 75-0488 042635-02 Washer Left Handle 149-9026 Potentiometer 042636-02 A040468-01 Left Handle Cover Harness

75-040S Split Lock Washer 476008-106 040249-01 Cap Screw Gear 040240-01 Bumper 72-8010 Screw

73-20807 142048-01 Roll Pin 4: 72-1206F Handle Bushing ‘Screw 12-003 Retaining Ring oe 040243-01 i At 4 042636-01 Bearing - a a Right Handle Cover

040244-01 Spring Pin

042634-01 Handle Frame

040246-01 Handle Spring

17602-3604 Self-Locking Screw 040235-01 176022-3606 Gear Self-Locking Screw ae 160026-001 040242-01 73-21208 Button Handle Shaft Roll Pin 040473-01 Switch Wire i i 176022-3610 042635-01 See Chapter 3 for lubrication information hae Fight Handle iaoeeetat Compression Spring

Figure 5-3 Flight-Control Assembly A042562-01 A

Page 44

Illustrated Parts Lists RETURN OF THE JEDI

176022-3604 Self-Locking Screw

040235-01 Gear

178012-001 Retaining Ring

175002-001 Large Washer 040238-01 Pin

042566-01 Steering Shaft

040243-01 Bearing

040239-01 Spring

177010-241 Nut

175002-004 Flat Washer

040237-01 Nut

040968-01 Gear

19-9026 Potentiometer

040236-01 Steering Assy Frame

040241-01 040240-01 Spacer Bearing Bumper

Figure 5-3 Flight-Control Assembly, continued A042562-01 A

5-8

Page 45

RETURN OF THE JEDI Illustrated Parts Lists

Flight-Control Assembly Parts List

Part No. Description A040468-01 Flight Control Harness Assembly 040235-01 60-Tooth Spur Gear 040236-01 Steering Frame 04023701 Anchor Nut

040238-01 Anchor Pin 040239-01 Steering Torsion Spring 040240-01 Stop Bumper 040241-01 Spacer Bearing

040242-01 Handle Shaft 040243-01 Bearing 040244-01 Spring Pin 040246-01 Handle ‘Torsion Spring

040248-01 Cover 040249-01 14-Tooth Spur Gear 040252-01 Compression Spring 040303-01 ‘Trigger 040473-01 Jumper Wire 040968-01 28-Iooth Spur Gear 042044-01 Button 042045-01 Handle Bushing

042566-01 Steering Shaft 042634-01 Handle Frame 042635-01 Right Handle 042635-02 Left Handle

042636-01 Right Handle Cover 042636-02 Left Handle Cover 160026-001 SPDT Snap Switch 175002-001 0.750-Inch I. D. Large Washer

175002-004 #10 Flat Washer 176008-106 #10-32 x %-Inch Self-Locking Socket Head Cap Screw 176022-3604 #6-32 x %-Inch Self-Locking Socket-Head Cap Screw 176022-3606 #6-32 x #-Inch Self-Locking Socket-Head Cap Screw

176022-3610 #6-32 x %-Inch Self-Locking Socket-Head Cap Screw 176025-3604 #6-32 x \4-Inch Tamper-Proof Button-Head Cap Screw 177010-241 #10-32 Nylock Hex Nut 178012-001 Retaining Ring for 0.750-Inch Diameter Shaft

178012-003 Retaining Ring for 3,-Inch Diameter Shaft 19-9026 5 k@ Potentiometer 72-1206F #2-56 x #-Inch Cross-Recessed Pan-Head Machine Screw 72-8010 #10-32 x %-Inch Socket-Head Cap Screw

72-8812 #8-32 x %4-Inch Socket-Head Cap Screw 73-20807 4-Inch Diameter x 7¢-Inch Long Spring Roll Pin 73-21208 $e-Inch Diameter x ¥%-Inch Long Roll Pin 75-07020 0.390-Inch I. D. Flat Washer

75-0408 #10 Split-Lock Washer 75-0488 #8 Split-Lock Washer

5-9

Page 46

Illustrated Parts Lists RETURN OF THE JEDI

Tube

99-11003 Starter 142028-001 Transformer 99-11009 Starter Socket

A005493-01 179035-001 Harness Tube Holder

A037540-01 Ground Wire

037469-01 Bracket

042667-01 Mounting Panel

NOTE To make sure the fluorescent tube starts, check that the ground wire is firmly attached to both the ballast transformer and steel tube bracket. For European games, makesurethe ground wireis firmly attached tothe transformer.

Figure 5-4 Fluorescent Tube Assembly US-Built A037458-01 C

5-10

Page 47

RETURN OF THE JEDI

A005493-02 Harness Illustrated Parts Lists

79-561816P Wire Nut 70-303 Tube 142028-602 042667-01 Transformer Mounting Panel

99-1012 Clamp

99-11009 Starter Socket 035835-01 Y¥-Lead Connector

Figure 5-4 Fluorescent Tube Assembly, continued Ireland-Built A037458-02 C

Parts List

Part No. Description

For US-Built Game A005493-01 Fluorescent Light Harness Assembly A037540-01 Ground Wire with Grounding Clip 037469-01 Tube Bracket 70-304 18-Inch, 15-Watt, Cool White Fluorescent Tube

99-11006 Fluorescent Tube Locking Tab (consists of two pieces) 142028-001 60 Hz, 118 V, Ballast Transformer 179035-001 2-Pin Fluorescent Tube Holder °

For Ireland-Built Game

A005493-02 Fluorescent Light Harness Assembly 035835-01 12-Inch Y-Lead Connector 70-303 18-Inch, 15 Watt, Cool White Fluorescent Tube 99-1012 1¥s-Inch Clamp 142028-002 50 Hz, 118 V, Ballast Transformer

For US- and Ireland-Built Games 042667-01 Wood Mounting Panel 79-561816P Spring-Connector Wire Nut for 16- to 18-Gauge Wires 99-11003 Fluorescent ‘lube Starter 99-11009 Starter Socket

Page 48

Illustrated Parts Lists RETURN OF THE JEDI

A035888-01 Transformer

WARNING Assembly

Fuse block cover must be in place during game operation.

Goncn A021084-xx ‘apacitor Voltage Plug

034544-01 Fuse Block Cover

79-4411001 78-70501SC Fuse Post Capacitor Bracket

46-2017002 Fuse

034482-02 Chassis

037639-01 # Label A035891-02 Fuse Harness Assembly

46-2014002 Fuse 78-2708 Bushing 46-301203 Fuse A034630-01 79-3206 Filter Assembly 46-2014002 _037641-01 (F Fuses RS Fuse Block ‘A035890-01 Power Harness

79-15021001 Terminal Block erm A034629-01 ®& ‘AC Harness 3A-MDA3501 Rectifier @ See parts list for Ireland part number.

Figure 5-5 Power Supply Assembly Ireland-Built A037671-09 J US-Built A037671-14 J

5-12

Page 49

RETURN OF THE JEDI Mlustcated Parts Lists

Power Supply Assembly Parts List

DesignatorDescriptionPart No.

For -09 Version

FLLabel for Fuse Value037639-02
FL4 A, 250 V, 3AG Slow-Blow Glass Cartridge‘Type Fuse46-2014002
BVoltage Block Assembly for 220 V (blue wire color) and 240 V (brown wire color)A037479-02

For -14 Version

FILabel for Fuse Value037639-01
FL7 A, 250 V Slow-Blow Glass Cartridge-Type Fuse46-2017002
J3Voltage Block Assembly for 120 V (yellow wire color)A021084-02

For -09 and -14 Versions

cl27,000 uk, 15 VDC Electrolytic Capacitor29-053
cl2-Inch Diameter Capacitor Mounting Bracket78-70501SC
CRI‘Type-MDA 3501 Bridge Rectifier3A-MDA3501
FIPanel-Mounting Non-Indicating 3AG Cartridge“Iype Fuse Post79-44N1001
F2-F65-Position 3AG Fuse Block with %-Inch Quick-Disconnect Terminals79-3206
F2-F6Fuse Block Cover034544-01
F2-F6Label for Fuse Values037640-01
F24 A, 250 V, 3AG Slow-Blow Glass CartridgeType Fuse46-2014002
F320 A, 32 V, 3AG Slow-Blow Glass Cartridge‘Type Fuse46-301203
F42-Circuit Single-Row Terminal Block79-15021001
F4-F64 A, 250 V, 3G Slow-Blow Glass Cartridge‘Type Fuse46-2014002
FLRFI Filter Assembly(designation not marked)A034630-01
J2Power Harness AssemblyA035890-01
J4aAC Harness AssemblyA034629-01
TITransformer Assembly(Acceptable substitute is part no. A035888-02)A035888-01

Power Supply Chassis Base (not shown) 034482-02

Fuse Harness Assembly A035891-02 Nylon Type 6/6 Hole Bushing with %-Inch Inside Diameter x 5%,Inch Outside 78-2708 Diameter x '4-Inch Thick

5-13

Page 50

Illustrated Parts Lists RETURN OF THE JEDI

A002465-01 Coin Counter A039254-01 Harness Assembly 179125-001 Grounding Clip

3 3 ND 5 040412-01 c Panel

  • 119006-103 Volume Control

° e >

176018-002 Screw

69-001 SelfTest Switch

WARNING Before removing or repairing the utilty panel, turn the game off. Players may receive an electrical shock ifthe utility panel is not properly grounded! After servicing any parts on the panel, make sure that the ground wire is firmly attached to the panel. 75-9910WO Stamped Nut

62-041 Auxiliary Coin Switch

Figure 5-6 Utility Panel Assembly A040413-01 C

Parts List

Part No. Description

A002465-01 Coin Counter A039254.01 Volume Control Harness Assembly (includes grounding clip) 040412-01 Component Panel 119006-001 Dual Volume Control

62-041 SPDT Pushbutton Auxiliary Coin Switch with Black Cap 69-001 DPDT SelfTest Switch 75-9910W0 1-32 Stamped Nut 176018-002 #632 x ¥4-Inch Thread-Forming Machine Screw 179125-001 Grounding Clip

5-14

Page 51

RETURN OF THE JEDI Illustrated Parts Lists

170000-001 99-15026

Lamp Coin Inlet

179047-001 Lamp Base 99-15023 Base Plate

99-15056 Screw for Bezel 99-15040 Lever

99-15025 a Coin Inlet al “O— 99-15054 Pivot for Lever

99-15055 Retaining Screw

75-9148 Hex Nut

; i ———_ 99-15028 Coin Return Box Lock Wash.

99-15056 99-15027 Screw for Bezel Coin Return Box

99-15075 Sw, Adjuster

99-15029 Bracket

75-3414S Screw

72-1414S Screw

Figure 5-7 Coin Controls, Inc. Coin-Door Assembly 171034-xxx A

5-15

Page 52

Ulustrated Parts Lists

99-15052 Spring for Button

99-15063 Screw

A037542-01 Harness—not shown

Oy’

99-15067 Lock Assy.

038091-01 Coin Box

99-5073 Upper Door 99-15074 99-5070 Lower Door | Doors and Frame 99-15072 Door Frame

171034-001 — U.S. 25¢/25¢ Coin Door 171034-003 — Canadian 25¢/25¢ Coin Door 171034-005 — 10 P/50 P Coin Door 171034-006 — U.K. 20 P/50 P Coin Door 171034-009 — German 2 DM/1 DM Coin Door 171034-010 — German 2 DM/5 DM Coin Door 171034-011 — German 1 DM/5 DM Coin Door 171034-015 — French 2 Fr/t Fr Coin Door RETURN OF THE JEDI

99-15067 Lock Assy. 99-15038 ae —— Bezel for Button

99-15001 thru 99-15011 Return Button

99-15039 Bezel for Cover

99-15066 Screw

Figure 5-7 Coin Controls, Inc. Coin-Door Assembly, continued

5-16 171034-xxx A

Page 53

RETURN OF THE JEDI Ulustrated Parts Lists

Coin Controls, Inc. Coin Door Assembly Parts List

Part No. Description

A036597-01 Harness Assembly (Ireland-built cabinet only) A037542-01 Harness Assembly 7214148 #4-40 x %-Inch Cross-Recessed Pan-Head Steel Machine Screw 75-056 #6 Internal-Tooth Zinc-Plated Steel Lock Washer

75-9148 #4-40 Steel Machine Hex Nut 75-3414S #440 x %-Inch 82° Cross-Recessed Flat-Head Steel Machine Screw 99-15001 Coin Return Button with U.S, 25-Cent Price Plate 99-15002 Coin Return Button with U.S, $1 Price Plate

99-15003 Coin Return Button with German 1 DM Price Plate 99-15004 Coin Return Button with German 2 DM Price Plate 99-15005 Coin Return Button with German 5 DM Price Plate 99-15006 Coin Return Button with Belgian 5 Fr Price Plate

99-15007 Coin Return Button with French 1 Fr Price Plate 99-15008. Coin Return Button with Japanese 100 Yen Price Plate 99-15009 Coin Return Button with British 10 Pence Price Plate 99-15010 Coin Return Button with Australian 20-Cent Price Plate

99-15011 Coin Return Button with Italian 100 Lire Price Plate 99-15025 Left Half of Coin Inlet 99-15026 Right Half of Coin Inlet 99-15027 Side Plate of Coin Return Box

99-15028 Base Plate of Coin Return Box 99-15029 Switch Bracket 99-15036 Metal Coin Return Cover 99-15038 Bezel for Coin Return Button

99-15039 Metal Bezel for Coin Return Button 99-15042 Coin Switch for US. 25 Cents 9915052 Spring for Coin Return Button 99-15055 Retaining Screw 9915056 #4-40 x 4e-Inch Cross-Recessed Pan-Head Steel Machine Screw 99-15060 Switch Cover 99-15063 Screw for Hinge 99-15066 Screw for Clamp

99-15067 Lock Assembly 99-15070 Doors and Frame 9915071 Clamp for Frame 9915072 Door Frame 99-15073 Upper Door

99-15074 Lower Door 9915075 Switch Adjuster 99-15083 Base Plate—includes: 99-15040 Lever 99-15054 Pivot for Lever

038091-01 Coin Box—not included in assembly (Acceptable substitute is part no. A037491-01) 170000-001 6.3 V Miniature Wedge-Base Incandescent Lamp 171006-035 Metal Coin Mechanism 171050-001 Dual Entry Face Plate 179047-001 Lamp Base

Page 54

Illustrated Parts Lists RETURN OF THE JEDI

99-10140 Panel Assembly

99-10147 Harness 75-9488 Locknut . 99-10116 Lever 99-10152 Z = Right Coin inlet f

171006-035, Coin Mechanism

75-9448 Locknut

99-10096 Fastener

99-10151 Left Coin Inlet

99-10105 Bar

99-10042 thru 99-10045 99-10154 Coin Switch Assembly Bracket Assembly

99-10153, Coin Return Box 99-10150 : ‘ Switch Cover 99-10068 Coin Chute 65-4410 , Coin Switch Nf 99-10075 thru 99-10078 I~ ‘Switch Wires 99-10008 Retainer 7544125

Screw

Figure 5-8 Coin Acceptors, Inc. Coin-Door Assembly 171027-001 A

5-18

Page 55

Illustrated Parts Lists

RETURN OF THE JEDI

99-10148 Lock Assembly

99-10142 Button Housing 72-HA1404C a Screw

99-10134 99-10119 Cover 99-10139 > |~——— Button Assembly | 9940118 Coin Door r, Z™> Button, i a ° - 99-10115, 99-10148 Spring Lock Assembly ~

99-10145, Sam ~ 99-10141

i Coin Return Cover

cca & . 99-10117

  • Coin Return Door

a 4 = 2

T-JAMOSB=aSl<—99-10144
crew a2Channel! Clip
Le59915066
  • Screw

Li 99-10149 ae . Service Door

038091-01 Za Coin Box Oe

99-10143

  • Frame

ee

Figure 5-8 Coin Acceptors, Inc. Coin-Door Assembly, continued 171027-001 A

5-19

Page 56

Mlustrated Parts Lists RETURN OF THE JEDI

Coin Acceptors, Inc. Coin Door Assembly Parts List

Part No. Description 65-441C Coin Switch 70-11-47 Miniature Bayonet Lamp 72-94068 #4-40 x $-Inch Truss-Head Screw 72-HAI404C #4-40 x %-Inch Pan-Head Screw 72-JAI405B #4-40 x .31-Inch Pan-Head Screw 75-1412 #4-40 x %-Inch Pan-Head Screw 75-9445, #4-40 Locknut 99-10008 Retainer 99-10042 Coin Switch Assembly for Belgian 5 Fr and USS. $.25 9910043 Coin Switch Assembly for German 1 DM, Japanese 100 Yen, Swiss 1 Fr 99-10044 Coin Switch Assembly for German 2 DM, Italian 100 L, U.S. $1.00 99-10045 Coin Switch Assembly for Australian $.20, German 5 DM, British 10 P 99-10068 Coin Return Chute

99-10075Switch Wire(included in coin switch assembly 99-10043)
99-10076Switch Wire(included in coin switch assembly 99-10042)
99-10077Switch Wire(included in coin switch assembly 99-10044)
99-10078Switch Wire(included in coin switch assembly 99-10045)

99-10080 Lamp Socket 99-1081 Key Holder 9910096 Fastener 99-10104 Bar Retainer 99-10105 Bar 9910115 Spring 99-10116 Plastic Coin Return Lever 99-10117 Steel Coin Return Door 99-10118 Amber Coin Return Button 9910119 Amber Coin Button for US. $.25 99-10134 Coin Button Cover 99-10139 Coin Door 99-10140 Coin Door Inner-Panel Assembly 99-10141 Die-Cast Coin Return Cover 99-10142 Die-Cast Button Housing 99-10143 Coin Door Frame 9910144 Channel Clip 99-10145, Cam 9910147 Harness 9910148 Lock Assembly 99-10149 Service Door 99-10150 Switch Cover 99-10151 Left Coin Inlet 99-10152 Right Coin Inlet 9910153 Coin Return Box 99-10154 Bracket Assembly 9915066 Screw for Clamp 038091-01 Coin Box 171006-035 Metal Coin Mechanism for U.S. $.25 177010-238 #8-32 Hex Locknut

5-20

Page 57

RETURN OF THE JEDI Illustrated Parts Lists

A042686-01 PIXI PCB See Figure 5-11 178120-104 een PCB Support 72-6810S Screw A041513-21 JEDI PCB Assembly See Figure 540

A035435-02 Regulator/Audio Il PCB See Figure 5-12

175004-708 Washer

75-99516 NutWasher Assy

034536-02 Foam Pad

034536-02 Foam Pad NOTE The PIXI1I PCBis notincluded inthe Main PCB Assembly. This part must. 176015-112 be ordered separately. Screw

Figure 5-9 Printed-Circuit Board Mounting Hardware

Parts List

Part No. Description

A035435-02 Regulator/Audio II Printed-Circuit Board Assembly A041513-21 JEDI Main Printed-Circuit Board Assembly A042686-01 PIXI II Printed-Circuit Board Assembly 72-1610, #6-32 x %-Inch Cross-Recessed Pan-Head Screw

72-6810S #8 x %-Inch Cross-Recessed Pan-Head Screw 75-0168 #6 Flat Washer 75-99516 #6-32 Nut/Washer Assembly 034536-02 ¥%-Inch Thick Foam Pad

175004-708 #8 Flat Fiber Washer 176015-112 #10 x %-Inch Cross-Recessed Pan-Head Screw 178120-104 \-Inch PCB Support

5-21

Page 58

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 59

RETURN OF THEJEDI Illustrated Parts Lists

TTT THT Ai 2 | — a . g a * ;

+] — a | (| |=

._c—) af |

Figure 5-10 Main PCB Assembly, continued A041513-01 D

5-23

Page 60

Illustrated Parts Lists RETURN OF THE JEDI

Main PCB Assembly Parts List

DesignatorDescriptionPart No.

Capacitors

cL100 pF, 100 Mica Capacitor128002-101
C239 pF, 100 Mica Capacitor128002-102
C40.01 #E, 25 V, Ceramic Capacitor122005-103
cs1 pE, 50 V, Electrolytic Capacitor24-500105
CO0.1 wE, 50 V, Ceramic Capacitor122002-104
C70.01 uF, 25 V, Ceramic Capacitor122005-103
c80.1 #F, 50 V, Ceramic Capacitor122002-104
C9-C120.01 wF, 25 V, Ceramic Capacitor122005-103
C15-C180.1 wE, 50 V, Ceramic Capacitor122002-104
C190.01 wF, 25 V, Ceramic Capacitor122005-103
21-230.01 #F, 25 V, Ceramic Capacitor122005-103
C250.01 #E, 25 V, Ceramic Capacitor122005-103
C280.1 #E, 50 V, Ceramic Capacitor122002-104
C30-C320.1 pF, 50 V, Ceramic Capacitor122002-104
C340.1 wE, 50 V, Ceramic Capacitor122002-104
35-420.01 wF, 25 V, Ceramic Capacitor122005-103
C48-C500.001 wF, 50 Ceramic Capacitor122002-102
C51, 520.01 wF, 25 V, Ceramic Capacitor122005-103
C540.01 wE, 25 V, Ceramic Capacitor122005-103
C56-610.01 uF, 25 V, Ceramic Capacitor122005-103
C62, C630.1 wE, 50 V, Ceramic Capacitor122002-104
C64, C650.01 wE, 25 V, Ceramic Capacitor122005-103
C66100 uF, 35 V, Electrolytic Capacitor24-350107
670.1 uF, 50 V, Ceramic Capacitor122002-104
C680.01 wF, 25 V, Ceramic Capacitor122005-103
C690.1 wE, 50 V, Ceramic Capacitor122002-104
C700.01 uF, 25 V, Ceramic Capacitor122005-103
C71, C720.0027 yF, $0 V, Ceramic Capacitor122015-272
C730.22 wF, 25 V, Ceramic Capacitor122008-224
C740.0027 uF, 50 V, Ceramic Capacitor122015-272
C750.01 pF, 25 V, Ceramic Capacitor122005-103
C760.1 pE, 50 V, Ceramic Capacitor122002-104
C77100 pF, 100 Mica Capacitor128002-101
C7839 pE, 100 Mica Capacitor128002-102
C79-C810.001 wR, 50 Ceramic Capacitor122002-102
C83-C85470 pE, 50 Ceramic Capacitor122013-471
C860.1 wE, 50 V, Ceramic Capacitor122002-104
C87, C88220 uF, 25 V, Electrolytic Capacitor24-250227
C890.1 wE, 50 V, Ceramic Capacitor122002-104
c900.1 FE, 50 V, Ceramic Capacitor122002-104
CoOL100 uF, 35 V, Electrolytic Capacitor24-350107
92-C1000.1 gE, 50 V, Ceramic Capacitor122002-104
C102-C1230.1 wE, 50 V, Ceramic Capacitor122002-104
C126-C1330.1 pF, 50 V, Ceramic Capacitor122002-104
C135-C1430.1 »E, 50 V, Ceramic Capacitor122002-104
C145-C1690.1 wE, 50 V, Ceramic Capacitor122002-104

(continued on next page)

5-24

Page 61

RETURN OF THE JEDI Illustrated Parts Lists

Main PCB Assembly Parts List, continued.

DesignatorDescriptionPart No.

Diodes

CRI‘Type-IN756 Diode321N756
CR2-CRI3Type-IN914 Diode31-INO14
CRI4Type-MV5053 Diode38-MV5053
CRISType 1N100/1N270 Diode31-IN100

Inductors

Li, L2100 wH Inductor141002-001
13-L51 gH Inductor141007-001

Integrated Circuits

1A‘Type-23128 ROM Integrated Circuit(Acceptable substitute is part136030-134

number 136030-114)

Ic‘Type-23128 ROM Integrated Circuit(Acceptable substitute is part136030-133

number 136030-113)

IF‘Type-23256 ROM Integrated Circuit(Acceptable substitute is part136030-131

number 136030-111)

lHType-23256 ROM Integrated Circuit(Acceptable substitute is part136030-130

number 136030-110)

1KType-23256 ROM Integrated Circuit(Acceptable substitute is part136030-129

number 136030-109)

1MType-23256 ROM Integrated Circuit(Acceptable substitute is part136030-128

number 136030-108)

IPType-74LS273 Integrated Circuit37-74L8273
IRSType-74L$273 Integrated Circuit37-74LS273
1TType-2364 ROM Integrated Circuit(Acceptable substitute is part136030-135,

number 136030-115)

24Type-74LS139 Integrated Circuit37-74LS139
2A/BType-74LS139 Integrated Circuit37-74LS139
2C2k x 8 RAM Integrated Circuit137211-001
2D‘Type-741$244 Integrated Circuit37-7ALS244
2EType-74LS138 Integrated Circuit137177-001
2FType-74LS273 Integrated Circuit37-74LS273
2HType-74LS194 Integrated Circuit37-74LS194
2JType-74LS194 Integrated Circuit37-74L8194
2K‘Type-74LS158 Integrated Circuit137203-001
2L‘Type-74LS194 Integrated Circuit37-7ALSIO4
2MType-74LS194 Integrated Circuit37-TALSI94
2NType-74LS32 Integrated Circuit37-74LS32
2P.Type-74L8245 Integrated Circuit37-74L8245
2R2k x 8 RAM Integrated Circuit137211-001
2sType-74LS194 Integrated Circuit37-7ALS194
2TType-74LS194 Integrated Circuit37-TALS194
3DType-74LS245 Integrated Circuit37-TALS245
3EType-74LS279 Integrated Circuit37-7ALS279
3FType-74LS86 Integrated Circuit37-7ALS86

(continued on next page)

5-25

Page 62

Illustrated Parts Lists RETURN OF THE JEDI

Main PCB Assembly Parts List, continued

DesignatorDescriptionPart No.
3H‘Type-74LS175 Integrated Circuit37-74LS175,
3y‘Type-74S374 Integrated Circuit137206-001
3KType-741S21 Integrated Circuit137210-001
3L‘Type-741S74 Integrated Circuit37-7ALSTA
3M‘Type-741$32 Integrated Circuit37-7ALS3,
3NType-74LS139 Integrated Circuit37-7AIS139
3P.‘Type-74LS32 Integrated Circuit37-741832
BRType-741S157 Integrated Circuit37-7ALSIST
3S‘Type-74LS157 Integrated Circuit37-741 S157
3TType-74LS157 Integrated Circuit377418157
3/4ACustom Integrated Circuit137324-1221
314CType-6502-A Integrated Circuit90-6013
4D‘Type-74LS273 Integrated Circuit37-74LS273
4EType-74LS374 Integrated Circuit37-74LS374
4F‘Type-74808 Integrated Circuit37-74808
4H‘Type-74L8283 Integrated Circuit137204-001
4Type-748157 Integrated Circuit37-748157
4KType-2149H-2 Integrated Circuit137199-002
4L‘Type-74LSI63A Integrated Circuit37-7ALSIOZA
4M‘Type-741S163A Integrated Circuit37-7ALSIOZA
4N‘Type-74LS163A Integrated Circuit37-7ALSIOZA
4P‘Type-2149H-2 Integrated Circuit137199-002
4R‘Type-7418257 Integrated Circuit37-7ALS257
4TType-741804 Integrated Circuit37-74804
5B‘Type-LM324 Integrated Circuit37-LM324
5DType TMS-5220 Integrated Circuit13 7308-001
5E‘Type-74L5374 Integrated Circuit37-74LS374
SFType-74LS00 Integrated Circuit37-74LS00
SHType-74LS283 Integrated Circuit137204-001
syType-74S157 Integrated Circuit37-748157
5KType-2149H-2 Integrated Circuit137199-002
5LType-741S163A Integrated Circuit37-TALSIOZA
5M‘Type-741S163A Integrated Circuit37-74LS163A
5NType-74LSI63A Integrated Circuit37-74LS163A
5PType-2149H-2 Integrated Circuit137199-002
5RType-7418257 Integrated Circuit37-74LS257
58Type-748374 Integrated Circuit137206-001
STType-74LS298 Integrated Circuit137201-001
6AType-LM324 Integrated Circuit37-LM324
6CType-741S163A Integrated Circuit37-7ALSI63A
OEType-7418257 Integrated Circuit37-7418257
OFType-74LS74 Integrated Circuit37-TALS74
OHType-74S74 Integrated Circuit3774874
ogType-741S174 Integrated Circuit37-TALSI74

5-26 (continued on next page)

Page 63

RETURN OF THE JEDI Illustrated Parts Lists

Main PCB Assembly Parts List, continued

DesignatorDescriptionPart No.
6KType-7418245 Integrated Circuit37-7ALS245
6L‘Type-7418245 Integrated Circuit37-74LS245
6MType-74LS273 Integrated Circuit37-7ALS273
6NType-23256 ROM Integrated Circuit(Acceptable substitute is part136030-127

number 136030-107)

OR‘Type-23256 ROM Integrated Circuit(Acceptable substitute is part136030-126

number 136030-106)

TAType-LM324 Integrated Circuit37-LM324
7DType-74C04 Integrated Circuit137309-001
7E‘Type-74LS04 Integrated Circuit37-TALSO4
TFType-74L832 Integrated Circuit37-7ALS32
7HType-74LS174 Integrated Circuit37-TALSI74
yType-74132 Integrated Circuit37-7ALS32
7KType-74LS00 Integrated Circuit37-74LS00
7LType-2114-2 Integrated Circuit90-7036
7M‘Type-2114-2 Integrated Circuit90-7036
JNType-2114-2 Integrated Circuit90-7036
7PType-74LS194 Integrated Circuit37-T4LS194
TRType-74LS194 Integrated Circuit37-7ALS194
8B‘Type-74L874 Integrated Circuit37-TALST4
8CType-74S74 Integrated Circuit37-74S74
8DType-74LS32 Integrated Circuit37-7ALSB2
8EType-74LS74 Integrated Circuit37-7ALST4
8FType-74LS86 Integrated Circuit37-74LS86
8H‘Type-74LS139 Integrated Circuit37-7ALSI39
8JType-74LS283 Integrated Circuit137204-001
8K‘Type-7418273 Integrated Circuit37-7ALS273
8L.‘Type-741S157 Integrated Circuit37-7ALSIST
8M‘Type-74LS157 Integrated Circuit37-74LS157
8N‘Type-74LS157 Integrated Circuit37-74LS157
8P‘Type-74LS194 Integrated Circuit37TALSIO4
8R‘Type-74LS194 Integrated Circuit37-TALS194
8SType-74LSI63A Integrated Circuit37-7ALS163A
9CType-74S112 Integrated Circuit137223-001
9D‘Type-74S74 Integrated Circuit37-TASTA
9E‘Type-74LSI0 Integrated Circuit37-74LS10
9H‘Type-82S129 Integrated Circuit136030-116
1)‘Type-74LS163A Integrated Circuit37-TALSIOBA,
OK‘Type-74S86 Integrated Circuit37-TALST4
OLType-741$283 Integrated Circuit137204-001
9MType-741S273 Integrated Circuit37-TALS273
ONType-741S283 Integrated Circuit137204-001
9PType-74L5245 Integrated Circuit37-7ALS245
oRType-74LS158 Integrated Circuit137203-001
9S,Type-748189 Integrated Circuit37-748189
OF‘Type-741S175 Integrated Circuit37-74LS175,

(continued on next page)

5-27

Page 64

Illustrated Parts Lists RETURN OF THE JEDI

Main PCB Assembly Parts List, continued

DesignatorDescriptionPart No.
10ACType-6502-B Integrated Circuit90-6012
10DType-74LS74 Integrated Circuit37-74LS7A
10EType-74LS74 Integrated Circuit37-TALS74
10F‘Type-74LS138 Integrated Circuit137177-001
10HType-74LS163A Integrated Circuit37-TALSIOZA
10)‘Type-74L832 Integrated Circuit37-74LS3
10KType-74LS74 Integrated Circuit37-74LS74
10LType-74LS08 Integrated Circuit37-74LS08
10MType-74832 Integrated Circuit37-74832
10PType-74LS175 Integrated Circuit37-7ALSI75
HAType-748244 Integrated Circuit137333-001
1BType-748244 Integrated Circuit137333-001
uc‘Type-741S245 Integrated Circuit37-74LS245
1D‘Type-74LS245 Integrated Circuit37-7ALS245
HE‘Type-74L808 Integrated Circuit37-74LS08
iFType-74LS138 Integrated Circuit137177-001
nHType-74804 Integrated Circuit37-74804
uyType-748163 Integrated Circuit137274-001
kK‘Type-74874 Integrated Circuit37-74S74
nLType-74LSI63A Integrated Circuit37-7ALSIOZA
11MType-74LS20 Integrated Circuit37-74LS20
1N‘Type-74LS00 Integrated Circuit37-74LS00
UPType-74S157 Integrated Circuit37-748157
MR‘Type-74S157 Integrated Circuit37-748157
usType-74S157 Integrated Circuit37-748157
1A‘Type-74LS175 Integrated Circuit37-TALSI75
12B, 12CType-X2212-30 Integrated Circuit137288-001
12DType-7415138 Integrated Circuit137177-001
12EType-74L808 Integrated Circuit37-74LS08
12F‘Type-74LS138 Integrated Circuit137177-001
12HType-74L800 Integrated Circuit37-74LS00
12L‘Type-74LS74 Integrated Circuit37-7ALS74
12M‘Type-74LS74 Integrated Circuit37-TALSTA
12N‘Type-74832 Integrated Circuit37-74832
12PType-2149H-3 Integrated Circuit137199-001
12RType-2149H-3 Integrated Circuit137199-001
12s.Type-2149H-3 Integrated Circuit137199-001
RTType-7406 Integrated Circuit37-7406
BA‘Type-23128 ROM Integrated Circuit(Acceptable substitute is part136030-125

number 136030-105)

BBIC‘Type-23128 ROM Integrated Circuit(Acceptable substitute is part136030-124

5-28 number 136030-104)

(continued on next page)

Page 65

RETURN OF THEJEDI Illustrated Parts Lists

Main PCB Assembly Parts List, continued

DesignatorDescriptionPart No.
BDType-23128 ROM Integrated Circuit(Acceptable substitute is part136030-123

number 136030-103)

13FType-23128 ROM Integrated Circuit(Acceptable substitute is part136030-122

number 136030-102)

13HType-74LS90 Integrated Circuit37-74L890
ByType-74LS14 Integrated Circuit37741814
BLType-74LS74 Integrated Circuit37-74LS74
13MType-74832 Integrated Circuit37-74832
BNType-7415245 Integrated Circuit37-7418245
13PType-74LS245 Integrated Circuit37-7ALS245
BRType-741S174 Integrated Circuit37-74LS174
BS‘Type-7415174 Integrated Circuit37-74L8174
BTType-741827 Integrated Circuit37-7ALS27
144Type-74L8257 Integrated Circuit37-74LS257
14BType-74LS257 Integrated Circuit37-74LS257
14B/C2k x 8 RAM Integrated Circuit137211-001
14D‘Type-ADC-0809 Integrated Circuit137243-001
14FType-23128 ROM Integrated Circuit(Acceptable substitute is part136030-121

number 136030-101)

14JType-74LS259 Integrated Circuit37-74LS259,

Transistors

QL, Q2Type-2N3904 Transistor34-2N3904
Q3, O4Type-2N6044 Transistor34-2N6044
Q5, 26‘Type-2N3906 Transistor33-2N3906
Q7Type-2N3904 ‘Transistor34-2N3904
8Type-2N3904 Transistor34-2N3904
QoType-2N3906 Transistor33-2N3906
QtoType-2N3904 Transistor34-2N3904
Qu‘Type-2N3906 Transistor33-2N3906
QiType-2N3904 Transistor34-2N3904
Q13Type-2N3906 Transistor33-2N3906
Qi4‘Type-2N3904 Transistor34-2N3904
O15Type-2N3906 Transistor33-2N3906
Q16Type-2N3904 Transistor34-2N3904

Resistors

RL10 kQ, 5%, % W Resistor110000-103
R210 kQ, +5%, % W Resistor110000-103
R32200, +5%, 4 W Resistor110000-221
RS4.7 kQ, +5%, 4 W Resistor110000-472
RO1kQ, +5%, 14 W Resistor110000-102
R72200, +5%, 4 W Resistor110000-221
RBTkQ, +5%, 4 W Resistor110000-102
RO10kQ, +5%, %4 W Resistor110000-103

(continued on next page)

5-29

Page 66

Illustrated Parts Lists RETURN OF THE JEDI

Main PCB Assembly Parts List, continued

DesignatorDescriptionPart No.
RIO1kQ, +5%, 4 W Resistor110000-102
RI10 kQ, +5%, % W Resistor110000-103
R13-R1G4700, +5%, 4 W Resistor110000-471
RI8-R211kQ, +5%, 4 W Resistor110000-102
R234700, +5%, 4 W Resistor110000-471
R25-R27470.0, +5%, 4 W Resistor110000-471
R29470.9, +5%, % W Resistor110000-471
R311kQ, 45%, %4 W Resistor110000-102
R33-R351kQ, +5%, 4 W Resistor110000-102
R371kQ, +5%, 4 W Resistor110000-102
R39-R421kQ, +5%, 4 W Resistor110000-102
R43,2200, +5%, 4 W Resistor110000-221
R442200, +5%, 4 W Resistor110000-221
R45-R471kQ, +5%, % W Resistor110000-102
R4839 kQ, +5%, 4 W Resistor110000-393,
R4939 kQ, +5%, %4 W Resistor110000-393,
RSO1 kM, +5%, 4 W Resistor110000-102
RS115 kQ, +5%, 4 W Resistor110000-153
R5215 kQ, +5%, 4 W Resistor110000-153
R531kO, +5%, % W Resistor110000-102
R541kQ, +5%, 44 W Resistor110000-102
R55,100 k@, +5%, 14 W Resistor110000-104
R56100 kQ, +5%, 4 W Resistor110000-104
R5722 kQ, +5%, 4 W Resistor110000-223
R58100 KO, +5%, 4 W Resistor110000-104
R5991K, £5%, 4 W Resistor110000-913
ROO100 kQ, +5%, 4 W Resistor110000-104
R6122kQ, £5%, % W Resistor110000-223
RO2100 kQ, +5%, % W Resistor110000-104
R63100 k®, +5%, % W Resistor110000-104
R6491 kQ, +5%, W Resistor110000-913
ROS10kQ, +5%, 4 W Resistor110000-103
ROG1.8k0,+5%, 4% W Resistor110000-102
RO?100 kQ, +5%, %4 W Resistor110000-104
R6812k, +5%, % W Resistor110000-123
R6O12 kM, 45%, 4 W Resistor110000-123
R7010 kQ, +5%, %4 W Resistor110000-103
R713.3kQ, +5%, 4 W Resistor110000-332
R721k, £5%, % W Resistor110000-102
R73.10 kQ, +5%, % W Resistor110000-103
R743.3kQ, +5%, 4 W Resistor110000-332
RIS.1kQ, +5%, %4 W Resistor110000-102
R763.3 kQ, £5%, 4% W Resistor110000-332
R7710 kQ, +5%, 4% W Resistor110000-103

(continued on next page)

Page 67

RETURN OF THE JEDI Illustrated Parts Lists

Main PCB Assembly Parts List, continued

DesignatorDescriptionPart No.
R7810kQ, +5%, 4 W Resistor110000-103
R792202, +5%, Y W Resistor110000-221
R80-R871kQ, +5%, 4 W Resistor110000-102
R88-R902200, +5%, % W Resistor110000-221
ROI-R931kQ, +5%, % W Resistor110000-102
RO44.7 kQ, +5%, & W Resistor110000-472
ROS10 kQ, 45%, % W Resistor110000-103
R9622k, +5%, % W Resistor0000-223
ROT15 kQ, +5%, %& W Resistor110000-153
ROS1kQ, +5%, 4 W Resistor110000-102
ROO820, +5%,% W Resistor110000-820
R100-R1021kQ, +5%, “ W Resistor110000-102
R1034.7kQ, +5%, 4 W Resistor110000-472
RIO410 kQ, 5%, 4 W Resistor110000-103
R10522 kQ, +5%, % W Resistor110000-223,
R10615 kO, +5%, % W Resistor110000-153
RIO71kQ, +5%, % W Resistor110000-102
R108820, +5%,%4 W Resistor110000-820
R109100.0, +5%, & W Resistor110000-101
RIO-R1121kQ, +5%, % W Resistor110000-102
RU34.7 kQ, +5%, % W Resistor110000-472
Ri410 kQ, +5%, 4 W Resistor110000-103
RUS22 kQ, £5%, % W Resistor110000-223,
RIUIG15k, +5%, %4 W Resistor110000-153
RUIZ1kQ, 45%, % W Resistor110000-102
RUS100 2, 45%, % W Resistor110000-101
RU9820, +5%,'4 W Resistor110000-820
R120-R1221kQ, +5%, 4 W Resistor110000-102
R1234.7 kQ, +5%, %& W Resistor110000-472
R12410 kQ, +5%, % W Resistor110000-103
R12522 kQ, +5%, 4 W Resistor110000-223
RI2615 kQ, +5%, ‘4 W Resistor110000-153
RI271kQ, +5%, 4 W Resistor110000-102
R128820, +5%,%4 W Resistor110000-820
R129100 Q, +5%, %4 W Resistor110000-101
R130150.0, +5%, 4 W Resistor110000-151
RI3Z1I-R1401kQ, +5%, 4 W Resistor110000-102

Sockets

1A28-Contact, Medium-Insertion-Force IC Socket79-42C28
1c28-Contact, Medium-Insertion-Force IC Socket79-42C28
ID28-Contact, Medium-Insertion-Force IC Socket79-42C28
IF28-Contact, Medium-Insertion-Force IC Socket79-42C28
1H28-Contact, Medium-Insertion-Force IC Socket79-42C28
IK28-Contact, Medium-Insertion-Force IC Socket79-42C28
1T28-Contact, Medium-Insertion-Force IC Socket79-42C28
IM28-Contact, Medium-Insertion-Force IC Socket79-42C28

(continued on next page)

Page 68

Illustrated Parts Lists RETURN OF THEJEDI

Main PCB Assembly Parts List, continued

DesignatorDescriptionPart No.
3/440-Contact, Medium-Insertion-Force IC Socket79-42C40
3/4C40-Contact, Medium-Insertion-Force IC Socket79-42C40
5D28-Contact, Medium-Insertion-Force IC Socket79-42C28
ON28-Contact, Medium-Insertion-Force IC Socket79-42C28
OR28-Contact, Medium-Insertion-Force IC Socket79-42C28
TOAIC40-Contact, Medium-Insertion-Force IC Socket79-42C40
10S/T28-Contact, Medium-Insertion-Force IC Socket79-42C28
12B18-Contact, Medium-Insertion-Force IC Socket79-42C18
12C18-Contact, Medium-Insertion-Force IC Socket79-42C18
13A28-Contact, Medium-Insertion-Force IC Socket79-42C28
13BIC28-Contact, Medium-Insertion-Force IC Socket79-42C28
13D28-Contact, Medium-Insertion-Force IC Socket79-42C28
13F28-Contact, Medium-Insertion-Force IC Socket79-42C28
14F28-Contact, Medium-Insertion-Force IC Socket79-42C28

Miscellaneous

@Nylon Snap-in Fastener81-4302
Q4Nylon Snap-in Fastener(Acceptable substitute is part no. 020670-01)81-4302
YI10.000 MHz Crystal90-123
Y212.096 MHz Crystal144000-001

5-32

Page 69

RETURN OF THE JEDI Illustrated Parts Lists

Figure 5-11 PIXI II Printed-Circuit Board Assembly A042686-01 A

Parts List

DesignatorDescriptionPart No.

Capacitors

cl22 , 25 V, Electrolytic Capacitor24-250226
C2-CB0.1 wE, 25 V, Ceramic Capacitor122006-104

Integrated Circuits

1AType-74LS163A Integrated Circuit37-7ALSIO3A
1BType-74LS125 Integrated Circuit137317-001
sTet‘Type-74S157 Integrated Circuit37-748157
12C‘Type-748374 Integrated Circuit137206-001
2BType-748374 Integrated Circuit137206-001
2/3CType-74LS174 Integrated Circuit37-7ALSIT4
3AType-741S163A Integrated Circuit37-74LS163A
4AType-741S30 Integrated Circuit37-74LS30
4BType-74LS174 Integrated Circuit37-TALSI74
5AType-74LS163A Integrated Circuit37-TALSIO3A
5BType-74802 Integrated Circuit37-74802
5C‘Type-74LS174 Integrated Circuit37-74L8174

Programmable Read-Only Memories & Random-Access Memory 24 Type-2149H-3 RAM Integrated Circuit

3BType-82S137 PROM Integrated Circuit136030-118
aCType-137336-025 PROM Integrated Circuit136030-117

Resistor

RI1kQ, 45%, % W Resistor110000-102

Miscellaneous Socket Terminal Carrier Assembly 179175-028

5-33

Page 70

Illustrated Parts Lists RETURN OF THE JEDI

2] ae ee nN

—| 338 +

—_C23c3l

35V 0 Seine} ree} R25 satnleF -+f 22

& aasup2cea

5.6K eee} eI 7812 7905

oO —4R24,12,7WE- Oo

TIP 32,TDAZO02 ATDAZ002A

=ig@2 1NAcoz Q5 arr

Rs.cre}a0.

AN ey 8 ceranllS GSIRS! |. C62 |.,o| cist

0ceca ~ {|eoS) Reenga

| 220] R21, \/2w Jociz yb 470 _* SR20 Gocu TaFRIO

3300uF + e tt

-0+3B

R30 RO, /2W ist cr,

  • -FINacoz, 9} C3 Uys —j+ 3300eF -—
4Ey35V

Figure 5-12 Regulator/Audio II PCB Assembly A035435-02 K

Page 71

RETURN OF THE JEDI Illustrated Parts Lists

Regulator/Audio II PCB Assembly Parts List

DesignatorDescriptionPart No.

Capacitors

cl470 pF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250477
c20.001 pF, 50 V, Ceramic-Disc Axial-Lead Capacitor122002-102
C30.1 pF, 50 V, Ceramic-Disc Axial-Lead Capacitor(Acceptable substitute is29-088

part no, 122002-104)

C4470 pF 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250477
cS0.01 pF, 25 V Minimum, Ceramic-Disc Axial-Lead Capacitor(Acceptable100015-103

substitute is part no. 122005-103)

C60.22 wk 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
co0.001 uF, 50 V, Ceramic-Disc Axial-Lead Capacitor122002-102
c80.22 pF, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
C9, C103300 pF, 35 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-350338
cu0.1 #, 50 V, Ceramic-Disc Axial-Lead Capacitor(Acceptable substitute is29-088

part no. 122002-104)

cl2470 pF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250477
ci.1000 pF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250108
cl40.01 pF, 25 V Minimum, Ceramic-Disc Axial-Lead Capacitor(Acceptable sub-100015-103

stitute is part no. 122005-103)

cis.0.22 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
cl60.001 wF, 50 V, Ceramic-Disc Axial-Lead Capacitor122002-102
cl70.22 pF 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
C18, C193300 pF, 35 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-350338
C20, C210.1 pF, 50 V, Ceramic-Disc Axial-Lead Capacitor(Acceptable substitute is29-088

part no. 122002-104)

€22, C23,1 pE, $0 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-500105
C2422 pF, 35 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-350226
C3122 wF, 35 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24350226

Diodes

CRIType-1N4002, 1 A, 100 V Silicon Rectifier Diode31-1N4002
CR4‘Type-IN4002, 1 A, 100 V Silicon Rectifier Diode31-1N4002
CR5-CR8Type-IN5401, 3 A, 100 V Silicon Rectifier Diode31-IN5401

Resistors

RI2700, +5%, 4 W Resistor110000-271
R333.0, +5%, % W Resistor110000-330
R4100 2, +5%, % W Resistor110000-101
R52.79, +5%, 1 W Resistor110009-027
RG3.9kQ, +5%, % W Resistor110000-392
R775 kQ, +5%, %4 W Resistor110000-752
R81 kQ Vertical PCB-Mounting Cermet Potentiometer119002-102
RO2200, +5%, % W Resistor110001-221
RIO10, +5%, % W Resistor110000-010
Ri100, 45%, %& W Resistor110000-100
RI21002, +5%, 4 W Resistor110000-101
R13, R1410kQ, +5%, 4 W Resistor110000-103

(continued on next page)

5-35

Page 72

Ilustrated Parts Lists RETURN OF THE JEDI

Regulator/Audio II PCB Assembly Parts List, continued.

DesignatorDescriptionPart No.
RID19, +5%, 4% W Resistor110000-010
R20100, +5%, 4% W Resistor110000-100,
R212200, +5%, % W Resistor110001-221
R221002, +5%, % W Resistor110000-101
R240.19, 43%, 7 W Wirewound Resistor19-100P1015
R25,49, +5%, 5 W Wirewound Resistor116001-040
R27, R281kQ, +5%, 4 W Resistor110000-102
R29, R30109,£5%, & W Resistor110000-100
R3122.9, +5%, 10 W Wirewound Resistor116000-220
R32, R335.6 kQ, +5%, % W Resistor110000-562

Transistors

Q2Type-TIP32 PNP Power Transistor33-TIP32
3‘Type-2N3055 NPN Silicon Transistor34-2N3055

Miscellaneous

J66-Position Connector Receptacle79-58306
J79-Position Connector Receptacle79-58308
Js4-Position Connector Receptacle79-58354
jo6-Position Connector Receptacle79-58306
yio12-Position Connector Receptacle79-58346
QlType-LM305, 5 V, Linear Voltage Regulator37-LM305
Q2, QDThermally Conductive Silicon Insulator78-16014
Q3Thermally Conductive Silicon Insulator78-16008
Q5TypeTDA2002A Linear Audio Amplifier137151-002
Q7‘Type-TDA2002A Linear Audio Amplifier137151-002
Q8Type-7812, +12 V, Voltage Regulator37-7812
Q9‘Type-7905, -5 V, Voltage Regulator37-7905

Heat Sink 034531-01 ‘Test Point (Acceptable substitute is part no. 179051-001) 179051-002

5-36

Page 73

RETURN OF THE JEDI

AC Alternating current; from zero it rises to a maximum positive level, then passes through zero again to a maximum negative level.

ACTIVE STATE The true state of a signal. For example: The active state for START is low.

ADDRESS ‘A value that identifies a specific location of data in memory; normally expressed in hexadecimal notation.

ANALOG Measurable in an absolute quantity (as opposed to on or off), Analog devices are volume controls, light dimmers, stereo amplifiers, etc.

ANODE The positive (arrow) end of a diode.

AMPLIFIER, A device used to increase the strength of an applied signal.

AMPLITUDE The maximum instantaneous value of a waveform pulse from zero.

ASTABLE Having no normal state. An astable device will free-run or oscillate as long as operating voltage is applied. The oscillation frequency is usually controlled by external circuitry.

AUXILIARY COIN SWITCH A momentary-contact pushbutton, switch with a black cap located on the utility panel. The auxiliary coin switch adds credits to the game without activating the coin counter. BEZEL A cut, formed, or machined retention device, such as the conical device used to mount a pushbutton switch to a control panel, or the formed device used to frame the video display screen. BIDIRECTIONAL Able to send or receive data on the same line (e.g., the data bus of a micro- Processor). BINARY A number system that expresses all values by using two digits (0 and 1). BIT A binary digit; expressed as a 1 or a0. BLANKING Turning off the beam on a cathode-ray tube during retrace.

BLOCK DIAGRAM A drawing in which functional circuitry units are represented by blocks. Very useful during initial troubleshooting. BUFFER 1, An isolating circuit designed to eliminate the reaction of a driven circuit on the circuits driving it (e.g., a buffer amplifier).

  • A device used to supply additional drive capability. ~ BUS An electrical path over which information is transferred from any of several sources to any of several destinations. CAPACITOR A device capable of storing electrical energy. A capacitor blocks the flow of DC current while allowing AC current to pass. CATHODE The negative end of a diode.

Glossary

CHIP An integrated circuit comprising many circuits on a single wafer slice. CLOCK A repetitive timing signal for synchronizing system functions. COINCIDENCE Occurring at the same time. COIN COUNTER A G-digit electro-mechanical device that counts the coins inserted in the coin mechanism(s). COIN MECHANISM A device on the inside of the coin door that inspects the coin to determine if the correct coin has been inserted.

COMPLEMENTARY Having opposite states, such as the outputs of a flip-flop. COMPOSITE SYNC Horizontal and vertical synchronization pulses that are bused together into a single signal. This signal provides the timing necessary to keep the display in synchronization with the game circuitry. COMPOSITE VIDEO Complete video signal from the game system to drive the display circuitry, usually comprising H SYNC, V SYNC, and the video.

CREDIT One play for one person based on the game switch settings. CRT Cathode-ray tube. DATA General term for the numbers, letters, and symbols that serve as input for device processing.

Gh1

Page 74

Glossary

DARLINGTON A two-transistor amplifier that provides extremely high gain. DC Direct current, meaning current flowing in one direction and of a fixed value.

DEFLECTION YOKE Electro-magnetic coils around the neck of a cathode-ray tube. One set of coils deflects the electron beam horizontally and the other set deflects the beam vertically. DIAGNOSTICS A programmed routine for checking circuitry. For example: the self-test is a diagnostic routine. DIODE A semiconductor device that conducts in only one direction. DISCRETE Non-integrated components, such as resistors, capacitors, and transistors. DMA Direct memory access. DMA is a process of accessing memory that bypasses the microprocessor logic. DMA is normally used for transferring data between the input/output ports and memory. DOWN TIME The period during which a game is malfunctioning or not operating correctly due to machine failure.

EAROM Electrically alterable read-only memory (see ROM). The EAROM is a memory that can be changed by the application of high voltage. FLYBACK A step-up transformer used in a display to provide the high voltage. GATE

  • A circuit with one output that responds when and only when a certain combination of pulses is present at the inputs.
  • A circuit in which one signal switches another signal on and off.
  • To control the passage of a pulse or signal. HARNESS A prefabricated assembly of insulated wires and terminals ready to be attached to a piece of equipment. HEXADECIMAL A number system using the equivalent of the decimal number 16 as a base. The symbols 0-9 and A-F are usually used.

GL2 IMPLODE To burst inward; the inward collapse of a vacuum tube.

vO Input/Output. IRQ Interrupt request. IRQ is a control signal to the microprocessor that is generated by external logic. This signal tells the microprocessor that external logic needs attention. Depending on the program, the processor may or may not respond. LED The abbreviation for a light-emitting diode. LOCKOUT COIL Directs coins into the coin return box when there is no power to the game.

LOGIC STATE The binary (1 or 0) value at the node of a logic element or integrated circuit during a particular time. Also called the logic level. The list below shows the voltage levels corresponding to the logic states (levels) in a TTL system. Logic 0, Low = 0 VDC to +0.8 VDC Grey Area (Tri-State Level) = +0.8 VDC to +2.4 VDC Logic 1, High = +2.4 VDC to +5 VDC

MULTIPLEXER ‘A device that takes several low-speed inputs and combines them into one high-speed data stream for simultaneous transmission on a single line. NMI Non-maskable interrupt. NMI is a request for service by the microprocessor from external logic. The microprocessor cannot ignore this interrupt request. PAGE A subsection of memory. A read-only memory device (see ROM) is broken into discrete blocks of data. These blocks are called pages. Each block has X number of bytes. PCB The abbreviation for a printed-circuit board.

PHOTOTRANSISTOR A transistor that is activated by an external light source. POTENTIOMETER

  • A resistor that has a continuously moving contact which is generally mounted on a moving shaft. Used chiefly as a voltage divider. Aiso called a pot (slang).

RETURN OF THE JEDI

  • An instrument for measuring a voltage by balancing it against a known voltage. RAM Random-access memory. A device for the temporary storage of data. RASTER-SCAN DISPLAY A display system whereby images are displayed by continuously scanning the cathode-ray tube horizontally and vertically with an electron beam. The display system controls the intensity of the electron beam.

RETRACE In a raster-scan display, retrace is the time during which the cathode-ray tube electron beam is resetting either from tight to left or from bottom to top.

RESISTOR A device designed to have a definite amount of resistance. Used in circuits to limit current flow or to provide a voltage drop. ROM Read-only memory. A device for the permanent storage of data.

SIGNATURE ANALYSIS A process of isolating digital logic faults at the component level by means of special test equipment called signature analyzers. Basically, signature analyzers (e.g., the ATARI® CAT Box) convert lengthy bit streams into four-digit hexadecimal signatures. The signature read by the analyzer at each circuit node is then compared with the known good signature for that node. This process continues until a fault is located.

TROUBLESHOOT The process of locating and repairing a fault. VECTOR A line segment drawn between specific X and Y coordinates on a cathode-ray tube. WATCHDOG A counter circuit designed to protect the microprocessor from self-destruction if a program malfunction occurs. If a malfunction does occur, the counter applies continuous pulses to the reset line of the microprocessor, which causes the microprocessor to keep resetting. X-Y DISPLAY A display system whereby images are displayed with vectors. ZENER DIODE A special diode used as a regulator. Its main characteristic is breaking down at a specified reverse-bias (Zener) voltage.

Page 75

TM-227 Ist printing

YOUR COMMENTS, PLEASE!

Your comments will assist Atari in improving our publications. The comments are an important part of preparing for revisions of game manuals. Please write in the space below. No postage stamp is necessary if mailed in the U.S.A.

If you have any technical questions about certain ATARI games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply:

Name

Firm O Distributor

Address CO Operator

City State Zip O Other

Area Code Phone

Page 76

POSTAGE WILL BE PAID BE ADDRESSEE

Atari Inc. Attn: Customer Service/Coin-Op Division 737 Sycamore Drive P.O. Box 906 Milpitas, California 95035 No postage necessary if mailed in the United States

Second Fold

aSpa stu adey, rosy

Page 77

TM-227 Ist printing

YOUR COMMENTS, PLEASE!

Your comments will assist Atari in improving our publications. The comments are an important part of preparing for revisions of game manuals. Please write in the space below.

If you have any technical questions about certain ATARI games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply:

Name

Firm U Distributor Address U Operator City Country U Other

Phone: Country Code Local Number

Page 78

First Fold

Attach Necessary Postage

Atari Ireland Limited Attn.: Field Service/Coin-Op Division

Tipperary Town, Ireland

word

Spa sp adey,

Page 79

Warranty

Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays (in games supplied with displays) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment, None of the Seller's other products or parts thereof are warranted If the products described in this manual fail to conform to this warranty, Seller's sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are returned to Seller during said warranty period, provided

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective; (b)Such products are returned prepaid to Seller's plant; and
  • Seller's mination Of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation, or improper testing, In no event shall Scller be liable for loss of profits, loss of use, incidental or consequential damages: Except for any express warranty set forth ina written contract between Seller and Buyer which contract supersedes the terms herein, this warranty ts expressed in liew of all other warranties expressed or bnplicd, including the implied warranties of merchantability and fitness for a particular purpose, and of all otber obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products by Seller. Pte, Natal lad, Salad Sates ated Nal’ 5

* > i

The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to you and others. Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.

Page 80

AL ® ATARI qyevereconsenencores

ATARI, INC. 1501 MCCARTHY BLVD. PO. BOX 906 MILPITAS, CALIFORNIA 95035 408/942-3100 ¢ TELEX 35-7488

© 1984 Lucasfilm Ltd. & Atari, Inc. Alll rights reserved. “Trademarks of Lucasfilm Lid. used by Atari, Inc. under license.