Macross
Super Spacefortress Macross / Chou-Jikuu Yousai Macross (Banpresto, 1992) · Document · 11 pages · 23 sections · original scan
OWNERS MANUAL
VIDEO GAME OPERATOR:
Don’t Get Involved In A Federal Crime. Don’t
Buy Or Operate Copy Or Unauthorized Boards In
Your Games.
Every operator who buys or operates a counterfeit or unauthorized board (imported or domestic) is contributing to the end of our industry and committing a FEDERAL CRIME. New criminal laws have recently been enacted that provide for maximum penalties of $250,000 or five years in prison or both, per offense. EACH GAME IS PARATE OFFENSE.
If you have any information about any unauthorized games in the United States, contact your local FBI or,
(American Amusement Machine Association
205 The Strand Suite 3 Alexandria, Virginia 22314 (703) 548-8044 All information will be treated in confidence.
SAFETY
The following topics should be carefully studied to insure maximum reliability and safety for both serviceman and customer. Shock Hazard: The high voltage on the monitor may be very dangerous. Extreme caution must be used when working with or around the monitors. Be certain that the grounding strap is attached to the monitor frame. The picture tube in the monitor is also a hazard and should be handled with care. Do not strike, scratch, or subject the tube to more than moderate pressure as it may implode serious injury from flying glass. Be certain that the control panel, power supply monitor, and coin door are all properly grounded to the ground wire inside the line cord. Do not remove ground prong off plug end.
PARTS LIST
1 - Control Panel Overlay 1 - FCC Label 1 - Manual 1 - Macross PCB 4 - Button Tags 1- Player Instruction 1 - Side Marquee
FABTEK® 8434 154th Avenue NE Redmond, WA 98052 (206) 881-0900 FAX (206) 881-6503
FOR SERVICE CONTACT:
Your authorized Fabtek® Distributor or SUMMIT SERVICE 2274 University Avenue St. Paul, MN 55114 (612) 645-9077
WARRANTY REPAIRS
Fabtek PCB have a 90 day warranty from date of shipment. This includes all failures except those caused by the installer such as miswiring.
All PCB must be returned by an authorized Fabtek distributor. A Return Material Authorization must be obtained from Summit Service prior to returning material. A Purchase Order must also be given to Summit Service at this time. The package must be clearly marked with the RMA number.
MACROSS? is protected by federal copyright laws and is the property of Fabtek®. Any unauthorized versions of this game are illegal by federal law. AAMA protected stickers must be attached to the PCB. Please notify Fabtek of any boards not having the AAMA seal.
THIS EQUIPMENT COMPLIES WITH THE REQUIREMENTS IN PART 15 OF FCC RULES FOR A CLASS A COMPUTING DEVICE. OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA MAY CAUSE UNACCEPTABLE INTERFERENCE OF RADIO AND TV RECEPTION REQUIRING THE OPERATOR TO TAKE WHATEVER STEPS ARE NECESSARY TO CORRECT THE INTERFERENCE. YOUR FCC COMPLIANCE LABEL IS ENCLOSED IN YOUR KIT AND MUST BE ATTACHED TO YOUR GAME PRIOR TO PLACING ON LOCATION. THIS LABEL INDICATES YOUR GAME WAS DESIGNED TO MEET FCC STANDARDS 47CFR15.19. WE ADVISE USING STAPLES IF NECESSARY TO MAKE SURE THE LABEL STAYS ON.
DANGER
The isolation transformer must be used with the monitor and power supply.
This game must be equipped with a three wire 110 volt plug for safety. Under no circumstance remove the ground plug.
This game is designed with a JAMMA 56 pin connector. This plug is one of the finest operator friendly features in our industry today. What this means to you is that:
) 1, 2, A, B, 27, 28, e and f are grounded ) 3,4, C and D are +5 volts ) 5 and E are -5 volts ) 6 and F are +12 volts
Also, all video and joystick functions are always in the same place. Once a cabinet is wired for JAMMA, it is easily changed from game to game.
Many older games such as Pac Man®, etc., have the power supply on the board. This will not work! Only aJAMMA connector with proper voltage will work. Fabtek® recommends using an 11 or 15 amp switching power supply with Macross®.
MONITORS
Macross* is designed to be operated with a vertical raster scan monitor with negative sync (RGB). This means Macross?® will not work with any X-Y (Tempest, Space Dual, Star Trec), etc. An isolation transformer must be used in conjunction with the monitor. This is for your safety. The monitor also utilizes extremely high voltages. The monitor may also retain a charge for an extended period of time. Safety goggles must be worn while removing or replacing the monitor.
Itis highly recommended that the monitor is verified good before the new Macross? kitis installed in your new and or rebuilt cabinet.
INSTALLATION OF KIT IN USED CABINET
To Disassemble:
- Open back door and remove old board set and power supply, if you are using a new switching power supply.
- Remove marquee glass and monitor glass.
- Remove control panel and set aside.
- Remove old wire harness, leaving 110 volt wiring intact. Also, leave the grounding straps to the monitor, coin door, control panel, and power supply intact.
Installation:
- Mount the board set on the side panel of the cabinet as close to the middle of the game as possible (approximately 10-12" off bottom).
- Mount the power supply on the bottom of the cabinet with connectors facing the rear of the cabinet. An optional mounting might be on the side panel just below the board set, connector to rear.
- Ifthe game does not have an isolation transformer, you must protect your customers and your game. Install one between the 110 volt line and your monitor/power supply.
- Place the provided JAMMA wiring harness on the board. Connect the +5, +12, -5, and ground wires to the corresponding lugs on the power supply, connecting all the wires. If you don't, you will probably burn the board connector.
- Run awire from +12 volts to the coin door lights. Run a wire from +12 volts to the coin counters. This completes the power requirements.
- Connect the Audio (+) and Audio (-) to the speaker.
- Connect the video red, green, blue, ground, and sync to the corresponding wires on the monitor. If the monitor is not a negative composite sync, see sync modifications chart.
- Cut the marquee to size. Replace the marquee lamp, if needed. Install the marquee panel.
- Connect the coin 1 and coin 2 wires to the coin switch. Connect the coin counter 1 and coin counter 2 wires to the coin counters.
- Disassemble the contro! panel of all the hardware. Do not remove the old panel overlay. Determine where to place the new joystick and buttons if they must be repositioned. Then, cut new holes.
Cutand drill plex as needed. Remove the old control panel overlay carefully and apply the new overlay ontop of the old glue. Use an Exacto knife to cut out any button or bolt holes. Apply necessary decals over appropriate buttons. Now assemble the control panel.
- Bolt the contro! panel to the cabinet. Now connect the appropriate wires to the correct switches. Connect the 1 player and 2 player start wires.
- Be sure to install the FCC stickers on the back of the cabinet.
- Power up the game. Look over your installation for errors, and then apply power, listening for unusual sounds. Check for smoke or sparks. If everything is okay, wire tie all wires to form a nice, neat wiring harness. Clean the cabinet inside and out. Measure the +5 volts on the furthest point from the edge connector and adjust 5 volts to 5.05 volts. Use a tinted plex over the monitor is there are burns in the screen. We suggest bronze or grey tinted plex. Touch up the cabinet with fresh paint, and then repair all cabinet dents or chips, using an auto body product called Duraglass. This is similar to bondo. You can consult your local auto body shop or auto parts supplier for this product, as well as advice on how to use it.
- Be sure your ground plug is good. All metal exposed to the player must be grounded (coin door, control panel, etc.) including all metal inside exposed.
MACROSS®
Fabtek recommends installing your new MACROSS kit in only a new or refurbished cabinet. Installing MACROSS in an older cabinet will result in lower earnings. The cabinet should be as follows:
- VERTICAL MONITOR
- 11 amp or larger power supply
PLAYER 1 START PLAYER 2
L@ @r ~~ ~
e e 8-WAY JOYSTICK 8-WAY JOYSTICK
1.
SOL EXI
FIG.
FIG. Monitor Sync \f your monitor does not have dual polarity positions for sync, you may use on of the following methods to get your game going.
CURE 1: Install a simple one |.C. Circuit on your logic board. This I.C. may be “piggy backed” on to another 7404 series chip for power by bending up all but the two power pins so that they are parallel to the top surface of the new I.C. and then connecting the power pins only to the existing chip. (See Fig. 1) Next connect the sync wires as shown in Fig. 2. (Note: Figure 2 shows a hookup for either composite or separate syncs.)
+5VDC
DER To STING CHIP ,
HORIZONTAL SYNC INPUT FROM P.C.B. +5VDC COR COMPOSITE SYNC INPUT > HORIZONTAL SYNC OUTPUT TO MONITOR NC. COR COMPOSITE SYNC OUTPUT > pgtsos VERTICAL SYNC INPUT FROM P.C.B. NC.
VERTICAL SYNC OUTPUT TO MONITOR NC. 74Ls04
NC. NC. GND
NC. NC.”
+ GROUND NC.
BENT PINS
FIG. 2
EXISTING I.c.
SOLDER
CURE 2: Used for Wells-Gardner Video-Sync boards with positive sync connections only. (Vertical mount board 85x14 OB.)
Cut the traces on the solder side of the board between input pins 5 & 6 to the unbanded (anode) ends of diodes X201 & X202. Add MPSA 56 transistor as follows: Collector to anode leads of diodes X201 & X202. Base pins 5 & 6 of the video input connector. Emitter to cathode (banded) lead of zener diode ZD201. Insert a 1N4148 diode - cathode to the emitter of the MPSA56 and anode to the base. (See Fig. 3)
1N4148 MPSASG
- a RED Fel
GREEN
BLUE
GND
VERT.
HORZ. zD201 on bw ne
x201 CUT BOTH TRACES
- Horizontal Tearing CAUSE: The negative sync signal of most logic sets are slightly different than the GO7-CBO monitor negative sync inputs. The result of this mismatch is a horizontal “wave” or “curl”.
CURE 1: On the monitor deflection board, replace C303 with a 10uf 25V radial lead capacitor with the positive lead towards the collector of X305. (CAUTION: be sure to check this step as the original cap is not polarized.) Then replace C501 with the cap removed from the C303 location.
CURE 2: Connect 1N4148 fast-switching diodes across both the positive and negative sync inputs to the monitor. (See Fig. 4) NOTE: Both diodes must be installed or you will not have vertical stability.
1N4148
NEGATIVE SYNC INPUT
- HORZ. — VERT. GND
FIG. 4 1N4148
+ HORZ. + VERT. GND BLUE GREEN RED
CURE 3: Join negative sync inputs J2 and J3 together with a jumper. Locate W102 and install a jumper from W102 to either J2 or J3.
CURE 4: For Wells-Gardner K4600 series monitors. Replace C356 (4 7uf 25V) on the Horizontal/vertical board (vertically mounted board nearest the flyback transformer) and center the horizontal hold pot. Turn L351 for the best horizontal stability and fine-tune with the horizontal width pot.
COIN COUNTER DIAGRAM
If only one coin counter is to be used install two diodes in the following manner:
ANa001 COIN COUNTER 1
COIN COUNTER COIN COUNTER 2
DIP SWITCH 1 MACROSS? DIP SWITCH SPECIFICATIONS
NUMBER OF PLAYERS ON
ON alalrwleo ON ON
DIFFICULTY NORMAL
EASY ON
HARD ON
HARDEST ON ON
LANGUAGE JAPANESE
ENGLISH ON
SCREEN INVERT NO
YES ON
DEMO SOUND YES
NO ON
MODE NORMAL
TEST MODE ON
DEFAULT SETTING OFF OFF OFF OFF OFF OFF OFF OFF
DIP SWITCH 2
COIN SWITCH A 1 COIN /1 PLAY
1 COIN / 2 PLAYS. ON
1 COIN /3 PLAYS ON 1 COIN / 4 PLAYS ON ON
1 COIN/5 PLAYS ON
1 COIN /6 PLAYS ON ON
1 COIN /7 PLAYS ON ON
2 COINS / 1 PLAY ON ON ON
2 COINS /3 PLAYS ON
2 COINS / 5 PLAYS ON ON
3 COINS / 1 PLAY ON ON
3 COINS / 2 PLAYS ON ON ON 3 COINS / 4 PLAYS ON ON
4 COINS / 1 PLAY ON ON ON
4 COINS /3 PLAYS ON ON ON
FREE PLAY ON ON ON ON
COIN SWITCH B 1 COIN / 1 PLAY
1 COIN /2 PLAYS ON
1 COIN / 3 PLAYS ON
1 COIN/ 4 PLAYS ON ON
1 COIN / 5 PLAYS. ON
1 COIN /6 PLAYS ON ON
1 COIN /7 PLAYS ON ON
2 COINS / 1 PLAY ON ON ON
2 COINS /3 PLAYS ON
2 COINS / 5 PLAYS ON ON
3 COINS / 1 PLAY. ON ON
3 COINS / 2 PLAYS ON ON ON
3 COINS / 4 PLAYS ON ON
4 COINS /1 PLAY ON ON ON
4 COINS / 3 PLAYS ON ON ON
5 COINS /3 PLAYS ON ON ON ON
DEFAULT SETTING OFF OFF OFF OFF OFF OFF OFF
JAMMA
re | op2[_]
PARTS SIDE
CPU PCB
Test Mode Turn on power source with No. 8 of DIP
SWITCH 1 “ON”. Finish dot-cross-hatch by button 1 of
1P. Continue your necessary examinations according to
instructions on screen. Finish test mode by power source
turned on again with No. 8 of DIP SWITCH 1 “OFF”. MACROSS® JAMMA EDGE CONNECTOR CABLE
COMPONENT SIDE SOLDER SIDE
FUNCTION COLOR COLOR FUNCTION
GROUND BLK BLK GROUND
GROUND BLK BLK GROUND
+5 VOLTS. RED RED +5 VOLTS
+5 VOLTS. RED RED +5 VOLTS
-§ VOLTS BRN BRN -5 VOLTS
+12 VOLTS BLU BLU +12 VOLTS
COIN COUNTER 1 BLU/BRN WHT/PUR COIN COUNTER 2}
N.C, alo|e|o}ol|njolo N.C.
AUDIO POS + WHT/BLK BLK AUDIO NEG -
N.C. N.C.
VIDEO RED RED GRN VIDEO GRN
VIDEO BLU BLU WHT VIDEO SYNC*
VIDEO GND BLK = BRN/WHT SERVICE SWITCH
N.C. YEL ry WHT/BRN N.C.
COIN INPUT 1 WHT/YEL. © GRN/YEL COIN INPUT 2
START 1 PNK/BLK bes RED/BLK START 2
1PUP ORG/BLU J BRN/BLU 2PUP
1 P DOWN GRN/ORG = ORG/WHT 2P DOWN
1P LEFT GRN/BLU & ORG/GRN 2P LEFT
1 P RIGHT RED/YEL WHT/ORG 2P RIGHT
1 P SHOOT RED/WHT BRN/BLK 2 P SHOOT
1 P BOMB WHT/RED YEL/WHT 2P BOMB
N.C. YEUBLK BRN/GRN NC.
NC NC.
N.C. N.C.
GROUND BLK BLK GROUND
GROUND BLK 8|<|ajofofwlu jz [> |x ))s]z/eljalolr|>/>/B)x]> [nN] e]2/ofojo|~
a BLK GROUND
“Video sync composite negative
ISOLATION
3 AMP, VARISTOR TRANSFORMER
SLO-BLO
410 VAC FUSE ON/OFF
SWITCH EMI FILTER
11 AMP GND currowmne = ws} 1,2,€,B GROUND 3,4,0,0 +5¥DC
LN 110 vac 1} oo tT] rower surety -s[ +12 5.E -S¥OC 6,F +12¥DC
COIN COUNTERS.
COUNTER
8 OHM SPEAKER AUDIO. AUDIO —
aaa SEO
RGB COLOR MONITOR 12 VIDEO RED N VIDEO GREEN 130 VIDEO BLUE P NEG COMP. 14 VIDEO GROUND 16 COIN INPUT #1 T COIN INPUT #2
VERTICAL SYNC
= COIN SWITCHES
COIN DOOR LIGHTS) #44 BULES 1ST PLAYER CONTROLS SHOMN = CIP C2P > 17 1P START u 2P START 21 RIGHT 20 LEFT 19 DOWN 18 uP, +KMED BOMB.
i]
sa OF arR Wa OFCEe ohh Oo0=z aE GAOrE SHOOT
moro 27,28,e,f GROUND
[oheteTa]
ty = MACROSS
8 WAY JOYSTICK