CATHODE RAY TOMES

Harley Davidson

Harley-Davidson & L.A.Riders (Sega Enterprises, USA, 1998) · Manual · 99 pages · 76 sections · original scan

Page 1

1ST PRINTING

Harley-Davidson & L.A.Riders

OWNER’S MANUAL

STD TYPE

SEGA ENTERPRISES, USA

MANUAL NO. 4200-6367

Page 2

Warranty

Your new Sega Product is covered for a period of 90 days from the date of shipment. This certifies that the Printed Circuit Boards, Power Supplies and Monitor are to be free of defects in workmanship or materials under normal operating conditions. This also certifies that all Interactive Control Assemblies are to be free from defects in workmanship and materials under normal operating conditions. No other product in this machine is hereby covered.

Sellers sole liability in the event a warranted part described above fails shall be, at its option, to replace or repair the defective part during the warranty period. For Warranty claims, contact your Sega Distributor.

Should the Seller determine, by inspection that the product was caused by Accident, Misuse, Neglect, Alteration, Improper Repair, Installation or Testing, the warranty offered will be null and void.

Under no circumstances is the Seller responsible for any loss of profits, loss of use, or other damages.

This shall be the exclusive written Warranty of the original purchaser expressed in lieu of all other warranties expressed or implied. Under no circumstance shall it extend beyond the period of time listed above.

Page 3

TABLE OF CONTENTS

INTRODUCTION OF THE OWNERS MANUAL GENERAL PRECAUTIONS 1. PRECAUTIONS TO BE HEEDED FOR OPERATION

  • NAME OF PARTS NYAMWRW

8.

9.

10. 11. 12.

13. 14.

15.

16.

17. 18. 19. . ACCESSORIES . ASSEMBLY AND INSTALLATION . PRECAUTIONS TO BE HEEDED WHEN MOVING MACHINE . CONTENTS OF GAME . EXPLANATION OF TEST AND DATA DISPLAY 7-1 POWER SUPPLY UNIT AND COIN METER 7-2: TEST MODE 7-3, MEMORY TEST 7-4 VIDEO MEMORY TEST 7-5 BOUNDRY TEST 7-6 INPUT TEST 7-7 OUTPUT TEST 7-8 SOUND TEST 7-9 C.R.T. TEST 7-10 GAME ASSIGNMENTS 7-11 COIN ASSIGNMENTS 7-12 REAL TIME CLOCK TEST 7-13 VOLUME SETTING 7-14 NETWORK ASSIGNMENTS 7-15 BOOKKEEPING 7-16 BACKUP DATA CLEAR HANDLEBAR 8-1 ADJUSTING/REPLACING THE FRONT BRAKE VOLUME 8-2. ADJUSTING/REPLACING THE ACCELERATOR VOLUME 8-3 ADJUSTING/REPLACING THE HANDLE BAR VOLUME 8-4 GREASING FOOT BRAKE MECHA 9-1 ADJUSTING AND REPLACING THE VOLUME 9-2. GREASING COIN SELECTOR MONITOR REPLACEMENT OF FLUORESCENT LAMP AND LAMPS 12-1 REPLACEMENT OF FLUORESCENT LAMP 12-2 REPLACEMENT OF LAMPS PERIODIC INSPECTION TABLE TROUBLESHOOTING 14-1 REPLACEMENT OF FUSES GAME BOARD 15-1 REMOVING THE IC BOARD 15-2 COMPOSITION OF THE GAME BOARD COMMUNICATION PLAY 16-1 INSTALLATION PRECAUTIONS 16-2 CONNECTING THE COMMUNICATION CABLES 16-3 SETTING FOR COMMUNICATION PLAY DESIGN RELATED PARTS PARTS LIST WIRING DIAGRAMS

Page 4

Installation space:

Height:

Weight:

Power maximum current:

MONITOR: SPECIFICATIONS

65 in.(L) x 31 in.(W)

78 in.

Approx. 397 lbs.

5 Amp AC 120V 60 Hz

29” INCH COLR MONITOR

INTRODUCTION OF THE OWNERS MANUAL

SEGA ENTERPRISES, LTD., has for more than 30 years been supplying various innovative and popular amusement products to the world market. This Owners Manual is intended to provide detailed descriptions together with all the necessary installation, game settings and parts ordering information related to the HARLEY DAVIDSON U/R, a new SEGA product.

This manual is intended for those who have knowledge of electricity and technical expertise, especially in ICs, CRTs, microprocessors, and circuit boards. Read this manual carefully to acquire sufficient knowledge before working on the machine. Should there be a malfunction, non-technical personnel should under no circumstances touch the interior system. Should the need arise, contact our main office, or the closest branch office listed below.

SEGA ENTERPRISES, INC. (USA) Customer Service 45133 Industrial Drive Fremont, CA 94538 Phone 650-802-1750 Fax 650-802-1754 7:30 am - 4:00 pm, Pacific Standard Time Monday thru Friday

Page 5

General Precautions

Follow Instructions: All operating and use instructions should be followed. Attachments: Do not use attachments not recommended by the product manufacturer as they may cause hazards. Accessories: Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use only mounting accessories recommended by the manufacturer. Moving the Product: This product should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product to overturn. Ventilation: Slots and openings in the cabinet are provided for ventilation, to ensure reliable operation of the product and to protect it from overheating; these openings must not be blocked or covered. The openings should never be blocked by placing the product in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

Power Sources: This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your location, consult your local power company. For products intended to operate from battery power or other sources, refer to the operating instructions. Grounding or Polarization: This product is equipped with a three-wire grounding-type plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug. Power Cord Protection: Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. Overloading: Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

Object and Liquid Entry: Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. Servicing: Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. Damage Requiring Service: Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

  • If the power cord or plug is damaged;
  • If liquid has been spilled, or objects have fallen into the product;
  • If the product has been exposed to rain or water;
  • If the product does not operate normally when following the operating instructions. Adjust only those controls that are explained in the operating instructions. An improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation;
  • If the product has been dropped or damaged in any way;
  • When the product exhibits a distinct change in performance; this indicates a need for service. Replacement Parts: When replacement parts are required , be sure the service technician has used replacements parts specified by the manufacturer or that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.
Page 6

Safety Check: Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. Heat: The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

Lithium Battery- Dispose of batteries only in accordance with the battery manufacturer’s recommendations. Do not dispose in an open flame condition, since the battery may explode. Cleaning: When cleaning the monitor glass, use water or glass cleaner and a soft cloth. Do not apply chemicals such as benzine, thinner, etc. Location: This an indoor game machine, DO NOT install it outside. To ensure proper usage, avoid installing indoors in the places mentioned below: + Places subject to rain/water leakage, or condensation due to humidity; In close proximity to a potential wet area;

  • Locations receiving direct sunlight;
  • Places close to heating units or hot air; eIn the vicinity of highly inflammable/volatile chemicals or hazardous matter;
  • On sloped surfaces; «In the vicinity of emergency response facilities such as fire exits and fire extinguishers;
  • Places subject to any type of violent impact;
  • Dusty places.

INSTALLATION PRECAUTIONS

  • Verify the amperage of the branch circuit outlet before plugging in the power plug. Do not overload the circuit.

+ Avoid using an extension cord. If one is required, use an extension cord of type SJT, 16/3 AWG rated min. 120 VAC, 7A.

  • Moving this unit requires a minimum clearance (of doors, etc.) of 32” (W) by 77” (H). ¢ For the operation of this machine, secure a minimum area of 32” (W) by 42”(D).

REGULATORY APPROVALS This game has been tested and found to comply with the Federal Communications Commission Rules. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This game has been tested and listed by Underwriters Laboratories, Inc., to ANSI/UL22.

LISTED

5K92

AMUSEMENT MACHINE

Page 7

1 . PRECAUTIONS TO BE HEEDED FOR OPERATION

In order to prevent accidents, be sure to comply with the following points before and during operation.

PRECAUTIONS TO BE HEEDED FOR OPERATION BEFORE STARTING THE OPERATION

@ In order to avoid accidents, check the following before starting the operation: Check if all of the adjusters are in contact with the surface. If they are not, the cabinet can move and cause an accident.

WARNING!

Ensure that all of the Adjusters are in contact with the floor.

Do not climb on the product. Climbing on the product can cause falling down accidents. To check the top portion of the product, use a step. @ To avoid electric shock, check to see if door & cover parts are 508.5

@ To avoid electric shock, short circuit and or parts damage, do not put the following items on or in the periphery of the product:

Flower vases, flower pots, cups, water tanks, cosmetics, and receptacles/ containers/vessels containing chemicals and water.

To avoid injury, be sure to provide sufficient space by considering the potentially crowded situation at the installation location. Insufficient installation space can cause the player to come into contact with or hit others

CAUTION! and result in injury or trouble.
Page 8

PRECAUTIONS TO BE HEEDED DURING OPERATION

A

CAUTION!

A

CAUTION! To avoid injury and accidents, those who fall under the following catagories are not allowed to play the game:
  • Intoxidated persons
  • Pregnant women or those in the likelyhood od pregnancy.
  • Those who need assistasnce such as the use of an apparatus when walking.
  • Those who have high blood pressure or heart problems.
  • Those who have experienced muscle convulsion or loss of consciousness when playing video games, etc.
  • Persons susceptible to motion sickness.
  • Persons whose acts runs counter to the products warning displays.
  • Instruct those who wear high-heeled shoes to refrain from playing the game by explaining that playing the game with highheeled showes is very dangerous and likely to cause a potentially hazardous situation.

To avoid electric shock and short circuit, do not allow customers to put hands and fingers or extraneous matter in openings of the product or small openings in or around doors. To avoid falling down and injury resulting from falling down, immediatly stop the customer’s leaning against or climbing on the product, etc. To avoid electric shock and short circuit, do not allow the customers to unplug the power plug without a justifiable reason.

Page 9

2 .NAME OF PARTS

BILLBOARD

29 INCH MONITOR

CABINET

COIN CHUTE DOOR 2 @ =

CASHBOX DOOR A

SEAT CABI

AC UNIT =O u*

GAME SPECIFICATIONS WIDTH LENGTH HEIGHT WEIGHT

DURING SHIPPING All measurements are in inches 475 LBS.

CABINET3hOX38”x78”350 LBS.
SEAT CABIBs”xX)455"—OXS49 LBS.
WHEN ASSEMBLED3X65”xX78"400 LBS.
Page 10
  • ACCESSORIES

KEY MASTER KEY DESCRIPTION OWNERS MANUAL 220-8576 (2) (2) Part No. (Qty.) — 4200-6367-01 (1) - For opening/closing For the CASHBOX DOOR

Note the doors Figures If Part No. has no description, the Number has not been registered or can not be registered. Such a part may not be obtainable even if the customer desires to purchase it. ‘Therefore, ensure that the part is in safekeeping with you.

VOL CONT B-5K OHM POP HOLDER 220-5484 (1) HLD-0004 (2) For communications

FUSES POP PANEL LOCAL PURCHASE 429-0162-91 (1) For communications

ae

CONN 29 FLEX TUBE 310-5287-29 (1) 310-5285-290150 (1) For communications For communications

ASSY FIBER CABLE UPPER JOINT 600-6275-0500 (3) HLD-0001 (1) For communications For communications

LOWER JOINT JOINT PLATE HLD-0002 (1) HLD-0003 (1) For communications For communications

Page 11

THE SHIPMENT METHOD DESCRIBED BELOW ONLY APPLIES TO ‘MODEL 3’ BOARDS CONTAINED IN THE

WARNING! FOLLOWING GAMES:

LOST WORLD, VIRTUA FIGHTER 3, SUPER GT, SEGA BASS FISHING, STRIKER 2 HARLEY DAVIDSON

'!INEVER SHIP MODEL 3 GAME BOARDS

OUTSIDE OF CAGE!!

CARTON BOX 601-8928 (1) Used for transporting the GAME BOARD. {SUPPLIED WITH YOUR GAME}

DO NOT SHIP GAME BOARD WITHOUT THIS BOX AS IT MAY DAMAGE THE GAME BOARD AND VOID YOUR WARRANTY.

“CHECK SIDE” Display

FILTER BOARD

THEY MAY BE DAMAGED BEYOND REPAIR. PLEASE SHIP THEM

() NO OTHER GAMES BOARDS ARE TO BE SHIPPED IN THE CAGE AS

WITHOUT CAGE PROPERLY PROTECTED DURING SHIPPING.

WARNING!
Page 12

4 .ASSEMBLING AND INSTALLATION

WARNING! Assembling should be performed as per this manual. Since this is a complex machine, erroneous assembling may cause damage to the machine, or malfunctioning to occur. When assembling, be sure to perform work by plural persons. Depending on the assembly work, there are some cases in which performing the work by a single person can cause personal injury or parts damage.

When carrying out the assembly work, follow the procedure in the following 7-item sequence:

A

CAUTION!

A

WARNING! 1 | ASSY OFCABINET

SECURING IN PLACE (ADJUSTER ADJUSTMENT)

POWER SUPPLY #} | Wy] } rm

ASSEMBLING CHECK

ote that the tools such as a phillips screwdriver and wrench for M16 hexagon bolt w/24 mm width across flats are required for the assembly work.

ASSY OF CABINET

Ensure that the connectors are accurately connected. Incomplete connections can cause electrical shock or short circuit. Be careful not to damage wirings. Damaged wiring can cause short circuit or electrical shock.

To perform work safely and securely, be sure to prepare a step which is in a secure and stable condition. Not using a step or using an unstable step can cause a violent falling down accident.

Page 13

Tightly fit the seat cabi to the cabinet in a manner to insert it in.

Secure to the cabinet with 2 hexagon bolts and 2 truss screws.

Connect the connector. (2P white)

Install the joint lid. OOOCLO Secure the Joint lid with 4 screws.

TRUSS SCREW (4) black JOINT LID M4x8

SCREW (1) M4x8, w/flat & spring washers

CONNECTOR 2P white

HEXAGON BOLT (2) black M8 x30, w/flat & spring washers

Page 14

2 SECURING IN PLACE (ADJUSTER ADJUSTMENT)

Be sure to have all the Adjusters make contact with the surface. Unless the Adjusters come into contact with the surface, the Cabinet

WARNING! can move of itself, causing an accident.

This machine has 8 each of casters and adjusters (shown below). When the installation position is determined, cause the adjusters to come into contact with the floor directly, make adjustments in a manner so that the casters will be raised approximately 5mm. from the floor and make sure that the machine position is level.

CASTERS

@ Move the machine to the installation position.

Q) Cause all of the leg adjusters to make contact . with the floor. By using a wrench, make

adjustments in the height of the leg adjusters to a)

ensure that the machine's position is level. =

ADJUSTERS

QB) After making adjustments, fasten the leg

adjuster nut upward and secure the height of the leg adjuster. BOTTOM VIEW

  • Depending on the floor surface status of the installation location, the Rear Cabinet may move of itself. As shown, the NON-SLIP SHEET is attached to the back side of the CAUTION MAT. Ensure that the Adjuster is installed in the manner to match the position of NON-SLIP SHEET
  • After making adjustments, fasten the adjuster nut upwards and secure the height of the adjuster

FASTEN UPWARD.

Approx. Smm

Page 15
WARNING! 3 | Power SUPPLY

@ Ensure that the power cord is not exposed on the surface (passage, etc.). If exposed, they can be caught and are susceptible to damage. If damaged, the cord can cause an electric shock or short circuit. Ensure that the wiring position is not in the customer's passage way or the wiring has protective covering.

The AC unit is mounted on the rear side of the cabinet . The AC Unit incorporates the Main SW, Earth Terminal and Inlet. Firmly insert the Power Plug into the Socket Outlet and the other side of the plug to the Inlet. Turn the Main SW ON to turn power ON.

® Ensure that the Main SW is OFF.

@ Connect the Power cord to the Outlet

Socket. Ensure power cord is not in customer’s passage way or wiring has protective covering. as

AC

/ BRACKET

FUSE MAIN SW

a

LINE STRAIN RELIEF \BINDING POST NOT USED

Page 16

ASSEMBLING CHECK

The TEST MENU allows for each part of the cabinet to be checked, the Monitor to be adjusted, and the coin and

game related various functions to be performed.

Va CPU ROM TEST ~

S

PRESS TEST BUTTON TO EXIT

coopIcastaan
oop1c.tan
oop13tnaen
GOOD{CROMOOMASK)ICHhens
GOOD(CROMISMASK)ICSteens
GOOD—_(CROMII MAS16tsann
GOOD(CROMILMASK)ICTthee
GOOD{CROMIOMASK).ICRhens
GOOD(CROMSSEPRON)ICOteens
GOOD(CRON? EPRONDseen
GOOD(CRON EPRONDeee
GOOD—_{CROMS0 EPRONDseen
GOOD{CRON EPRONDsees
GOOD(CRON? EPROMseen
GOOD{CRON EPROMseen
GOOD{CROMOEPROM)IC IG_tee

PRESS TEST BUTTON T0 EX

/ INPUT TEST

HANDLEBAR or THROTTLE oF FRONT BRAKE oF REAR BRAKE oF

VIEW CHANGE or MUSIC SELECT oF HUET UP oF SHIET DOWN oF

start om

comet or

SERVICE SW or TES oF

XN

Ne >EXIT OUTPUT TEST

START LAMP

VIEW CHANGE LAMP

MUSIC SELECT LAMP

RACE READER LAMP OFF

OFF

OFF

OFF

SELECT WITH SERVICE BUTTON

PRESS TEST BUTTON TO EXIT J \ Selecting the MEMORY TEST on the test mode menu screen causes the on-board memory to be tested automatically. The game board is satisfactory if the display beside each IC No. shows GOOD.

Selecting the INPUT TEST on the menu screen in the test mode to display the screen on which each SW and Volume is tested. Press each switch. (To check the Coin SW, insert a Coin from the inlet with the Coin Chute Door being opened.) If the display beside each switch is ON, the switch and wiring connection are satisfactory. Check the display of each Volume value. The Volume could have an irregularity caused by differences between machines and vibration during transportation. Set the Volume values by referring to Section ?

In the output test mode, carry out lamp test to ascertain that each lamp lights up satisfactorily.

Page 17

la SOUND TEST

No «o)

>EXIT

SELECT WITH SERVICE BUTTON PRESS TEST BUTTON TO EXIT

CRITEST 1/2

We 7 ~_— PRESS TEST BUTTON TO CONTINUE wy

Ick Test 2p Ne

a

yy In the TEST mode, selecting SOUND TEST causes the screen, on which sound related BD and wiring connections are tested, to be displayed. be sure to check if the sound is satisfactorily emitted from each of speaker and the sound volume is appropriate.

In the TEST mode menu, selecting C.R.T. TEST allows the screen (on which the projector is tested) to be displayed. Although the projector adjustments have been made at the same time of shipment from the factory, color deviation, etc., may occur due to the effect caused by geomagnitism, the location building’s steel frames and other game machines in the periphery. By watching the test mode screen, make judgement as to whether an adjustment is needed. If it is neccessary, adjust the projector by refering to Section 9.

Perform the above inspections also at the time of monthly inspection.

Page 18

5 . PRECATIONS TO BE HEEDED WHEN MOVING THE MACHINE

@ When moving the machine, be sure to pull out the plug from the power supply. Moving the machine with the plug as is inserted can damage the power cord and cause a fire or electric shock. @ When moving the machine on the floor, retract the Adjusters and ensure that Casters make contact with the floor. During transportation, pay careful attention so that Casters do not tread power cords. Damaging the power cords can cause an electric shock and/or short circuit. @ When lifting the cabinet, be sure to hold the catch portions or bottom part. Lifting the cabinet by holding other portions can damage parts and installation portions, due to the empty weight of the cabinet, and cause personal injury.

WARNING!

Use care when handling glass made parts. When the glass is damaged, fragments of glass can cause injury

CAUTION!

Where there steps (or step-like differences in grade), move the machine by seperating jams) into each unit.

Uta Y

CASTER On level surfaces, move the machine by causing the _ handlebar can damage the handle bar. Pushing the glass made or plastic parts can damage the parts and cause injury. Also, moving machine by holding the

casters to make contact with the surfaces.

Page 19

6 .CONTENTS OF GAME

The following are operations and responses obtained when the machine functions satisfactorily. Any functioning different fromt he following may have been caused by a certain fault. Immediately investigate and eliminate the cause of the malfunctioning to ensure satisfacory operation. The explanation herein mainly refer to the case where the game machine is used independently. In communications play, some points may differ fromthe following explanations.

When energized, the Billboard’s fluorescent lamp is always lit. During ADVERTISE (in the status a coin(s) is not inserted), the contents of game and HOW TO PLAY, etc., are audiovisually explained. The status of the on-tank 3 buttons will change to and from lighting up/flashing/lights out. Although the Start button is unlit during ADVERTISE, it blinks if even one coin is inserted, and is always lit duriong game play. The View Change button and Music Select button are unlit during ADVERTISE and lit when the Select Mode is displayed. During Game, the flash alternately. The two lamps of the Billboard flash during ADVERTISE and Select Mode display, light up during game and flash for approximately 3 seconds at the time of passing the checkpoint. In case of communication play, the lamps light up during game, flash for approximately 3 seconds when passing the chackpoint (in top posistion), and light out for 3 seconds when passing the checkpoint (in the second position or lower).

BILLBOARD

SHIFT UP button

SHIFT DOWN button FRONT BRAKE LEVER

START button

VIEW CHANGE button —|

COIN INLET ~~ | ACCELERATOR p—_ ACCELERATOR

MUSIC SELECT button

REAR BRAKE PEDAL

Page 20

Be seated.

Insert coin(s). When one play worth of coin(s) is inserted, the Select mode appears. Select in order of BIKE and TRANSMISSION. Turn the handlebar to select and turn the ACCELORATOR GRIP

to decide.

When the Select Mode is displayed, countdown starts. At count 0, BIKE TRANSMISSION being selected are CIOTS)

automatically decided.

REMAINING TIME REMAINING TIME

Turn the handlebar and twist the grip tmiciacnvadaaieage

QOOCOCOO OOCOCO0O BIKE SELECT TRANSMISSION SELECT

® When TRANSMISSION is decided, the race starts. The checkpoint (desination) is displayed on the screen, and Time Limit countdown starts.

At the same time the race starts, the View Change button and Music Select button alternately light up/light out. Pressing the View Change button changes the View point in the game mode. Pressing the Music Select button changes the BGM (background music).

® The distance to the checkpoint is displayed onthe upper left section of the screen. the remaining time is indicated on the upper center, score points on the upper right, navigation window(map) on the lower left, and speedometer on the lower right. DISTANCE 10 CHECKPOINT SCORE Pt CHECKPOINT \ REMAINING TINE | ONT f to Airport y J aotom cs GO 2 30000pts

COMPETITOR’ S MARKER

COMPETITOR Pail a (SEAT NO.) DIRECTION OF CHECKPOINT PLAYER’ S i POSITION \ COMPETITOR ra NAVIGATION |]

1st STAGE moor

NAVIGATION WINDOW GAME MODE SPEEDOMETER

Page 21

Run towards the checkpoint by judging the route from the arrow and the NAVIGATION WINDOW. Passing the checkpoint within the time limit results in a Stage Clear. The time limit is extended and the next checkpoint is i)

displayed.

If the player fails to pass the checkpoint within the time limit, the game is over. © 2

Passing all of the checkpoints results in a Game Clear. The successful player can see the ending mode.

After a Game Over, the accomplishment results are displayed on the map. © ©

If the player scores high points, the Name Entry mode appears. Turn the Handlebar, select character, and turn the Accelorator Grip to register intial, etc.

NOTE 1:

Setting change can be made to no sound output during ADVERTISE.

NOTE 2:

In the case where several machines are linked together for communication play, the bike appearing first in the Select Mode is predetermined by the number of each cabinet set for the communication play.

NOTE 3:

The setting of the number of checkpoints required for game clear is changeable.

KNACK OF GAME PLAY

To make full use of bike characteristics;

Each of the 5 types of bike has specific characteristics. High points can be earned by fully utilizing the bike charcteristics and selecting the type which suites best for the player.

To memorize the courses;

The player will surely acomplish a game clear by selecting the course on which he can make full use of the bike characteristics instead of relying on the map and arrow.

Page 22

. EXPLANATION OF TEST AND DATA DISPLAY

By operating the switch unit, periodically perform the tests and data check. When installing the machine initially or collecting cash, or when the machine does not function correctly, perform checking in accordance with the explanations given in this section. The following shows tests and modes that should be utilized as applicable.

TABLE 7 EXPLANATION OF TEST MODE

ITEMS DESCRIPTION SECTIONS

When the machine is installed, perform the following: INSTALLATION | |. Check to see that each setting is as per standard setting made 7-10, 7-11 OF MACHINE at the time of shipment.

  • In the INPUT TEST mode, check each SW and VR. 7-6
  • In the OUTPUT TEST mode, check each of lamps. 7-7
  • In the MEMORY TEST mode, check ICs on the IC Board. 7-3,7-4

MEMORY Choose MEMORY TEST in the MENU mode to allow the MEMORY test to be performed. In this test, PROGRAM RAMs, ROMs, and ICs on the IC Board are checked.

PERIODIC Periodically perform the following: SERVICING

  • MEMORY TEST 7-3,7-4
  • Ascertain each setting. 7-10,7 -ll
  • In the INPUT TEST mode, test the CONTROL device 7-6
  • In the OUTPUT TEST mode, check each of lamps. 7-7
CONTROL1. In the INPUT TEST mode, check each SW and VR.7-6

SYSTEM

  • Adjust or replace each SW and VR. 8

3 If the problem can not be solved yet, check the CONTROL’s moves. 8

PROJECTORIn the PROJECTOR ADJUSTMENT mode, check to see if the7-9

PROJECTOR adjustment is appropriately made.

IC BOARD 1. MEMORY TEST

2.In the SOUND TEST mode, check the sound related ROMs. 7-8

DATA CHECKCheck such data as game play time and histogram to adjust the7-15

difficulty level, etc

Page 23

7-1 SWITCH UNIT AND COIN METER

Never touch places other than those specified. Touching places not specified can cause electric shock and short circuit.

@ Adjust to the optimum sound volume by considering the environmental requirements of the installation location. @ If the COIN METER and the game board are electrically disconnected,

IMPORTANT! game play is not possible.

Open COIN CHUTE DOOR, and the switch unit shown appears. The function of each switch is as follows:

SWITCH UNIT

(SOUND VOLUME

Controls the speaker volume of the right/left speakers on the coin chute tower.

(2) TEST BUTTON (TEST SW)

For the handling of the TEST BUTTON, refer to the section on test mode.

QB) SERVICE BUTTON (SERVICE SW)

Gives credits without registering on the coin meter.

VOL. FRONT VOL. SEAT

O VOLFRONT VOLSEAT “” TESTSW_SERVICESW _ DEMAG, SW

TEST | SERVICE DEMAG. SW.

Page 24

7-2 TEST MODE

This mainly checks if the operation of the game BD is accurate, and allows for COIN ASSIGNMENTS/GAME ASSIGNMENTS setting and Projector adjustments. Va TEST MENU

PU MEMORY TEST VIDEO MEMORYTEST BOUNDRY SCAN TEST INPUT TEST OUTPUT TEST SOUND TEST CRITEST GAME MENTS. COIN ASSIGNMNETS NETWORK ASSIGNMENTS

VOLUME ADIUSTMENTS

REAL TIME CLOCK TEST BOOKKEEPING BACKUP DATA CLEAR >EXIT

SELECT WITH SERVICE BUTTON

AND PRESS TEST BUTTON

NS Jo

@

@

FIG. 7.2 TEST MENU. Push the TEST BUTTON to cause the follow-

ing TEST MENU to appear:

By pushing the SERVICE BUTTON, bring the “>” mark to the desired item and press the TEST BUTTON. This will select the item’s

test.

After the test is complete, move the “>” mark to “EXIT” and press the TEST BUTTON to return to game mode.

The Following FIGURES/TABLES show the factory recommended settings.

7-3 MEMORY TEST

( CPU ROM TEST

GOOD(CROMO3 MASK)ea
GOOD(CROMO2 MASK)Ic2
GOOD(CROMOI MASK)Ics
GOOD(CROMOO MASK)Ica
GOOD(CROMI3 MASK)Ics
GOOD(CROMI2 MASK)Ico
GOOD(ROM MASK)ic7
GOODROMO MASK)Ics
GOOD(CROMS3EPROM)«C9

GOOD (CROMS2EPROM)—IC.10

Good(CROMSI EPROM)ICI
GOOD(CROMS0EPROM)C12
GOOD(CROM3 EPROM)ies
GOOD(CROM2 EPROM)ies
GOODROM! EPROM)Ieas
GOOD(ROMO EPROM)Ic16

PRESS TEST BUTTON TO EXIT \ \

FIG. 7.3a MEMORY TEST

Va CPU ROM TEST

Goop(SDRAM)Ie.3
GoopBACK UP SRAM)1c.21
GoopCROLL SDRAM)IC.94 or IC.19
GooD(SCROLL SDRAM)IC.17

PRESS TEST BUTTON TO EXIT Ics Ic.2 1c.20 Ic.18

FIG. 7.3b MEMORY TEST The MEMORY TEST mode is for checking the on-BD memeory IC functioning. “GOOD” is displayed for normal ICs and “BAD” is displayed for abnormal ICs

This test starts immediately after selection from the menu in the test mode. When in execution, the “TESTING NOW” message will be displayed at the lower part to the screen. Press the Test Button to proceed to CPU RAM TEST

Test starts immediately after proceeding to this mode from CPU ROM TEST. During execution, the “TESTING NOW” message will be displayed at the lower part of the screen. When an error occurs, the ERROR message is shown. After finising the test, press the TEST button to return to the menu mode.

Page 25

7-4 VIDEO MEMORY TEST

a

Goop Goop coop coop coop Goop Goop Goop Goop Goop coop Goop Goop coop coop coop VIDEO BOARD ROM TEST

(VROMO1) (VROMOO) (VROMO3) (VROMO2) (VROMOS) (VROMO4) (VROMO7) (VROMOS) (VROM11) (VROM10) (VROMI3) (VROMI2) (VROMI5) (VROMI4) (VROMI7) (VROM16) Ic30 Ic3 1c32 1C33 Ic34 Ics 1C36 1c37 Ic38 1c39 Ica0 Ica

PRESS TEST BUTTON TO CONTINUE ~

FIG. 7.4a VIDEO MEMORY TEST

Va

X VIDEO BOARD RAM TEST

PRESS TEST BUTTON TO CONTINUE ~S

7-5 BOUNDRY SCAN TEST FIG. 7.4b VIDEO MEMORY TEST

Va

NS BOUNDRY SCAN TEST

TOTAL ERRORS.

PRESS TEST BUTTON TO EXIT \

/

FIG. 7.5 BOUNDRY SCAN TEST This allows the functioning of the VIDEO MEMORY IC’s on the IC board to be checked.

“GOOD” is displayed for normal IC’s and “BAD” is displayed for abnormal IC’s if any.

Test starts immediately after proceeding to this mode from the menu in the test mode. During execution, the “TESTING NOW” message will be

didplayed at the lower portion of the screen. After fininshing the test, press the TEST BUTTON to proceed to VIDEO RAM.

Test starts immediately after proceeding to this mode from the VIDEO BOARD ROM TEST.

During execution, the “TESTING NOW” message will be displayed at the lower portion of the screen. If staus is satisfactory, nothing will be displayed. After fininshing the test, press the TEST BUTTON to return to the menu mode.

Selecting the “BOUNDRY SCAN TEST” causes the Game board’s testing in terms of hardware to be performed automatically.

When the test is completed, if the results are as shown left, it is satisfacory.

After finishing the test, press the TEST BUTTON to have the MENU MODE return on the screen.

Next, turn power off and then turn it back on again. To avoid malfunctioning, have the Board intialized by turning the power off and then on.

If there is any hardware problems, an error message is displayed. Please contact the offices herein stated or where the product was purchased from.

Page 26

7-6 INPUT TEST

When INPUT TEST is selected, the MONITOR will show the following, allowing you to watch the status of each switch and the value of each VR.

Va

HANDLEBAR THROTTLE, FRONT BRAKE REAR BRAKE,

VIEW CHANGE MUSIC SELECT SHIFT UP SHIFT DOWN

START

COIN

SERVICE-SW TEST-SW INPUT TEST

OFF OFF OFF OFF

orF OFF OFF OFF

OFF

OFF

orF OFF ~\

/

SHIFT UP

suet pom

—START__

VIEW CHANGE _

_cOIN 4x REAR BRAKE FIG. 7.6 INPUT TEST

7-7 OUTPUT TEST __ HANDLEBAR

Va

START

VIEW CHANGE

MUSIC SELECT

RACE READER

>EXIT OUTPUT TEST

LAMP,

LAMP,

LAMP,

LAMP, OFF

OFF

OFF

OFF

SELECT WITH SERVICE BUTTON ~\ FRONT BRAKE_

/ FIG. 7.7 OUTPUT TEST

r ) This test mode displays the status of each switch, button, and

Volu me. When the switch/button corrsponds to the name of the item is pressed, if OFF changes to ON, it is satisfactory. When corresponding Volume is operated, if the Volume value differs in a natural manner, it is satisfactory.

APPROPRIATE VALUE OF TENSION VOLUME

Tension volume values are displayed in hexadecimal numerals within the range of OOH~ffH. If the value does not satisfy the following limitations, adjust the Volumes gear mesh so as to meet the requiremnts.

LOWER LIMIT: Over 05H

UPPER LIMIT: Under faH

@ Press the test button to return to the menu mode

YN RACE LEADER LAMP Lo —_\

START LAMP

VIEW CHANGE LAMP

__MUSIC SELECT LAMP

Choose OUTPUT TEST to cause the following lower screen to appear. In this test, check the status of each lamp.

@ Pressing the TEST BUTTON causes “ON” to be displayed and the corresponding lamp lights up. Pressing the TEST BUTTON again cuases “OFF” to be displayed and the lamp goes off. The Foot Controller is locked with the Slide Lock in the ON status, and

Unlocked to become free with the Slide Lock in the

OFF status.

@ Press the test Button to return to the MENU MODE.

Page 27

7-8 SOUND TEST

No o)

>EXIT

SELECT WITH SERVICE BUTTON \ PRESS TEST BUTTON TO EXIT yy, FIG. 7.8 SOUND TEST

7-9 C.R.T. TEST

a an >)

MMM

it Terr 7 FIG. 7.9 C.R.T. TEST This enables sound used in the game to be checked. Sound related memory and each speaker are checked.

@ Press the SERVICE BUTTON to increse the number by one and the sound corresponding to the number will be emitted. Note that No. 000 does not emit any sound.

@ Bring the “>” to EXIT and press the TEST BUTTON to return to the MENU MODE.

Select C.R.T. TEST to cause the MONITOR to display the screen shown left, allowing MONITOR adjustment status to be checked.

Periodically check the MONITOR adjustment status on this screen.

The screen (1/2) enables color adjustment check to be performed. The color bar of each of the 4 colors, i.e..red, green, blue, and white, is the darkest at the extreme left and becomes brighter towards the extreme right.

Press the TEST BUTTON to shift to the next screen (2/2).

The screen (2/2) allows screen size and distortion to be tested.

Check if the CROSSHATCH FRAME LINE goes out of the screen and if the crosshatch lines are distorted.

Press the TEST BUTTON to return to the MENU mode.

Page 28

7 - 10 GAME ASSIGNMENTS

Selecting the GAME ASSIGNMENTS in the MENU mode causes the present game settings to be displayed and also the game settings changes (game difficulty, etc.) can be made. Each item displays the following content.

SETTING CHANGE PROCEDURE

S PORTANT! Setting changes cannot be stored unless the TEST BUTTON is pressed while the arrow is on EX IT.

  • Press the SERVICE BUTTON to move the “>” to the desired item.
  • Choose the desired setting change item by using the TEST BUTTON.

® To return to the MENU mode, move the arrow to EXIT and press the TEST BUTTON.

a

Ne (GAME ASSIGNMENTS \ ADVERTISE SOUND ON GAME DIFFICULTY NORMAL CABINET TYPE STANDARD

BGM. VOLUME 4 ENGINE VOLUME, 8

NUMBER OF STAGES 4

TOURNAMENT MODE ON START MONTH DEC DAY 25 YEAR 1998, HOUR 18 END MONTH DEC DAY 25 YEAR 1998, HOUR 18

DURATION DAILY > EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTTON

@ CABINET TYPE Set to DELUXE or STANDARD as applicable. Setting to wrong type can causefailure be sure to set correctly. (i.e. In communication Play Race Leader Lamp does not light up/flash/light out. The Cabinet appearing in the operation explanation mode differs from the type used.)

@ TOURNAMENT MODE During the period set, special bookkeeping for ranking is executed. When set to ON, as shown above, the date of Tournament Mode Start, the end date of Tournament Mode, and itmes of bookkeeping periods are displayed. Duration refers to the unit of bookkeeping periods. The setting can be selected from among DAILY, WEEKLY, BI-WEEKLY, and MONTHLY .Be sure to set the present time in the Tournament Mode. @ ADVERTISE SOUND Determines wether ADVERTISE SOUND is to be emitted or not by the setting to ON when emitting it and to OFF when not emitting it.

@ GAME DIFFICULTY Sets the Game Difficulty in 5 catagories from | to

  • The greater the number is, the higher the difficulty level becomes. Alternately it may display each catagory by name; Very Easy, Easy, Normal, Hard, Very Hard

@ BGM. VOLUME BGM Volume Adjustment.

@ ENGINE VOLUME Engine Volume adjustment

The Following FIGURES/TABLES show the factory recommended settings.

Page 29

7-11 COIN ASSIGNMENTS

The “COIN ASSIGNMENTS” mode permits you to set the start number of credits, as well as the basic numbers of coins and credits. This mode expresses “how many coins correspond to how many credits.”

SETTING CHANGE PROCEDURE

Gror Setting changes cannot be stored unless the TEST BUTTON is pressed

while the arrow is on EXIT.

RTANT!

oO) Press the SERVICE BUTTON to move the arrow to the desired item. @ Choose the desired setting change item by using the TEST BUTTON.

@ To return to the MENU mode, move the arrow to EXIT and press the TEST BUTTON.

/ COIN ASSIGNMENTS \

COIN CHUTE TYPECOMMON@COIN CHUTE TYPE
CERISE POSTSRESCREDETS.Sets the combination of the number of COIN CHUTEs and

CREDIT TO CONTINUE 1 CREDIT 4 the number of players as applicable. In the case that the COIN/CREDIT SETTING #1 A a COIN CHUTE is changed, be sure the setting is made in a

CHUTES,ICONTCREDITmanner meeting the replaced coin chute.
CHUTE1COIN1 CREDITCOMMON:

Coins are accepted in common for both players.

MANUAL SETTING

INDIVIDUAL: >EXIT Each player uses a coin chute which accepts coins independently.

SELECT WITH SERVICE BUTTON LS ‘AND PRESS TEST BUTTON yy,

@ CREDITTO START Number of credits required for starting game (1~5 credits are selected.)

@ CREDITTO CONTINUE Number of credits required for continuing game (1~5 credits are selected.)

@ COIN/CREDIT SETTING Sets the CREDITS increase increment per coin insertion. There are 27 setings from #1 to #27, expressed in XX CREDIT as against XX COINS inserted. (TABLE 7.11a, 7.11b) #27 refers to FREE PLAY. When the COIN CHUTE TYPE is set to INDIVIDUAL, there are some setting numbers not displayed as indicated in TABLE 7.11b.

@ MANUAL SETTING This allows credit increase setting as against coin insertion to be further set in the manner finer than COIN/ CREDIT SETTING (refer to TABLE 7.1 Ic).

Page 30

TABLE 7.11a COIN/CREDIT SETTING (COIN CHUTE COMMON TYPE)

SETTING FUNCTIONING OF CHUTE#1

SETTING #11 COIN1 CREDIT
SETTING #21 COIN2 CREDITS
SETTING #31 COIN3 CREDITS
SETTING #41 COIN4 CREDITS
SETTING #51 COIN5 CREDITS
SETTING #61 COIN2 CREDITS
SETTING #71 COIN5 CREDITS
SETTING #81 COIN3 CREDITS
SETTING #91 COIN4 CREDITS
SETTING #101 COIN5 CREDITS
SETTING #111 COIN6 CREDITS
SETTING #122 COINS1 CREDIT.
SETTING #131 COIN1 CREDIT
SETTING #141 COIN2 CREDITS
SETTING #151 COIN1 CREDIT

2 COINS 3 CREDITS

SETTING #161 COIN3 CREDITS
SETTING #173 COINS1 CREDIT
SETTING #184 COINS1 CREDIT
SETTING #191 COIN1 CREDIT

2 COINS 2 CREDITS 3 COINS 3 CREDITS 4 COINS 5 CREDITS

SETTING #201 COIN5 CREDITS
SETTING #215 COINS1 CREDIT
SETTING #221 COIN2 CREDITS
SETTING #232 COINS1 CREDIT

4 COINS 2 CREDITS 5 COINS 3 CREDITS

SETTING #241 COIN3 CREDITS
SETTING #251 COIN1 CREDIT

2 COINS 2 CREDITS 3 COINS 3 CREDITS 4 COINS 4 CREDITS 5 COINS 6 CREDITS

SETTING #261 COIN1 CREDITS

SETTING #27 FREE PLAY

Page 31

MANUAL SETTING

>EXIT

NS COIN TO CREDIT

BONUS ADDER

COIN CHUTE #1 MULTIPLIER I COIN COUNTS AS 1 COIN COIN CREDIT

COIN CHUTE #2 MULTIPLIER L COIN COUNTS AS 1 COIN COIN CREDIT MANUAL SETTING 1COIN —-LCREDIT. = — NO BONUS ADDER —]

20345678
2 03456789
23456789
23456789

/ SELECT WITH SERVICE BUTTON

AND PRESS TEST BUTTON

FIG. 7.11b MANUAL SETTING

@ Determines Coin/Credit setting.

@ This sets how many coins should be inserted to obtain one Service Coin. Selecting MANUAL SETTING in the COIN ASSIGNMENTS mode displays the following screen. )--0

@ This sets how many tokens one coin represents.

Table 7.11c MANUAL SETTING

COIN TO CREDIT 1 COIN 1 CREDIT. 2 COINS 1 CREDIT. 3 COINS 1 CREDIT. 4 COINS 1 CREDIT. 5 COINS 1 CREDIT. 6 COINS 1 CREDIT. 7 COINS 1 CREDIT 8 COINS 1 CREDIT 9 COINS 1 CREDIT.

BONUS ADDER NO BONUS ADDER 2 COINS GIVE 1 EXTRA COIN 3 COINS GIVE 1 EXTRA COIN 4 COINS GIVE | EXTRA COIN 5 COINS GIVE 1 EXTRA COIN 6 COINS GIVE | EXTRA COIN 7 COINS GIVE 1 EXTRA COIN 8 COINS GIVE 1 EXTRA COIN 9 COINS GIVE 1 EXTRA COIN

COIN CHUTE MULTIPLIER 1 COIN COUNTS AS 1 COIN 1 COIN COUNTS AS 2 COINS 1 COIN COUNTS AS 3 COINS 1 COIN COUNTS AS 4 COINS 1 COIN COUNTS AS 5 COINS 1 COIN COUNTS AS 6 COINS 1 COIN COUNTS AS 7 COINS 1 COIN COUNTS AS 8 COINS 1 COIN COUNTS AS 9 COINS

Page 32

7-12 REAL TIME CLOCK TEST

/ REALTIME CLOCK TEST

QSDEC 1997 THRU 185530

BATTERY OK.

pay 2s

MonTH bec YEAR 1997 HOUR 8 MINUTE 5s SECOND 30 DAY OF THE WEEK THU

ser

>EXIT

SELECT WITH SERVICE BUTTON XS "AND PRESS TEST BUTTON Fig. 7.12 REAL TIME CLOCK TEST

7-13 VOLUME ADJUSTMENTS

a VOLUME ADJUSTMENTS

HANDLE BARMIN (00)MAX (FF)
THROTTLEMIN (00)MAX (FF)
FRONT BRAKEMIN (00)MAX (FP)
REAR BRAKE,MIN (00)MAX (FF)

EXIT WITH SAVE

EXIT WITHOUT SAVE

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON TO EXIT \

NUETRAL (80) CHECKING (00) CHECKING (00) CHECKING (00)

S Fig. 7.13b VOLUME SETTING

7-14 NETWORK ASSIGNMENTS

Va NETWORK ASSIGNMENTS

CABINET ID NUMBER 1

>EXIT

SELECT WITH SERVICE BUTTON

LO PRESS TEST BUTTON TO EXIT

COMMUNICATION NETWORK

PRIVILEGE MODE, MASTER \

SY FIG. 7.14 NETWORK ASSSIGNMENTS The system of this product has calandar functions. In the Game Assignments, if the Tournament mode is set to ON, ensure the present time is correct in this mode.

  • Press the Service button and bring arrow to the desired item to be changed.
  • Press the test button to change year, month, day, and hour.
  • Bring the arrow to SET and press test button.
  • Move the arrow to EXIT and press the TEST button to return to menu mode.

In the case an appropriate value is not displayed in the input test mode, the Volume can be adjusted in this mode. Set an appropriate Volume value by moving the HandleBar, Accelerator Grip, Front Brake, and Rear Brake fully within it’s movable range. The numeral values are hexadecimally displayed.

@ HANDLE BAR: After turning the handlebar fully to the left and right, return it to the cneter and ensure the status in which force is not exerted. @ THROTTLE: After fully moving accelerator grip, let go your hold and return to the status in which force is not exerted. @ FRONT BRAKE: Fully grip the front brake and let go your hold, then return to the status in which force is not exerted. @ REAR BRAKE: Fully step on the rear brake pedal and then release to return to the status of which force is not exerted.

Bring the cursor to EXIT WITH SAVE and press the test button to have the contents of the new input setting registered and return to the menu mode. Bring the cursor to EXIT WITHOUT SAVE to return to the menu mode without changing the current settings.

THIS TEST MENU ALLOWS FOR THE ADJUSTMENT OF THE NETWORK SETUP.

@ COMMUNICATION: Select NETWORK or STAND ALONE. When NETWORK is selected, the following are displayed.

@ PRIVILEGED MODE: In the case plural machines are used for interactive play, set one of them to MASTER and set the rest of them to SLAVE. The Game Assignments set to the MASTER cabinet will also be applied to the SLAVE cabinets. Changing the settings by the SLAVE units is ineffective.

@ CABINET ID NUMBER: In the case of plural machines are linked for interactive play, set the CABINET ID NUMBER in the order of 1, 2,3, and 4 starting from the left most cabinet as seen from the front of the cabinet. If an identical number is set to 2 or more cabinets or if settings is made in the wrong order, the display during the game will be incorrect. Be careful of this point.

Page 33

7 - 15 BOOKKEEPING Choosing BOOKKEEPING in the MENU mode displays the data of operating status up to the present are shown on 2 pages. Press the TEST BUTTON to proceed to PAGE 2/2.

/BOOKKEEPINGTAGE>@COIN CHUTEM:

COIN REPORT Number of coins put in each Coin Chute.

COIN CHUTE #1 XXXXXXXXXXX

COIN CHUTE #2XXXXXKXXKEX@TOTAL Cos:

TOTAL COINS XXXXXKXXXKX woe .

COIN CREDITSXXXKXXXKXKKTotal number of activations of Coin Chutes.

SERVICE CREDITS XXXXXXXXXXX TOTAL CREDIT XXXXXXXXXXX

NUMBER OF GAMES @ COIN CREDITs:

1 P.GAMES'XXXXXXXXXXXNumber of credits registered by inserting coins.

2 PGAMES XXXXXXXXXXX NUMBER OF CONTINUE

1 PGAMESXXXXXXXXXXX@SERVICE CREDITS:

2 PGAMES: XXXXXKXXXKX : : Credits registered by the SERVICE BUTTON.

TOTALTIMEXDXXHXXMXXS
PLAYTIMEXDXXHXXMXXS
AVERAGE PLAYTIMEXXMXXS@TOTAL CREDITS:
LONGEST PLAYTIMEXXMXXSTotal number of credits (COIN CREDITS+SERVICE
SHORTETEST PLAYTIMEXXMXXSCREDITS)
NePRESS TEST BUTTON TO CONTINUE/@ TOTAL TIME:

FIG. 7.15a BOOKKEEPING (1/2) The total energized time.

aBOOKKEEPINGPAGE 22 \

TIME HISTOGRAM XXXXXXXX XXXXXXXX XXXXXXXX On page (2/2), each play frequency is displayed. When XXXXXXXX etting diffi ev e Te:

= ins SECGOCX setting difficulty levels, the frequency can be refered to as a

IMI0s ~ IM19SXXXXXXXXstandard.

M208 ~ 1298 XXXXXXXX MOS ~ 1M395 XXXXXXXX

IMdos ~ 1M49SXXXXXXXXWhen in the PAGE 2/2 mode, press the TEST BUTTON to

IMS0S ~ 1MS9S XXXXXXXX

4M00s ~ 4M09SXXXXXXXXreturn to the MENU mode.

4ML0S ~ 4M198 XXXXXXXX

4M20S~ 4M298XXXXXXXX

4M30S ~ 4398 XXXXXXXX 4Ma0s ~ 4M498 XXXXXXXX 4MS0S ~ 4MS9S XXXXXXXX sMO0S ~ XXXXXXXX

NePRESS TEST BUTTON'TO EXITyy,

FIG. 7.15b BOOKKEEPING (2/2)

7-16 BACKUP DATA CLEAR Clears the contents of BOOKKEEPING and high BACKUP DATA CLEAR . /— > score player ranking entry.

oenay @ = When clearing, bring the arrow to “YES” and when

not clearing, to “NO”, by using the SERVICE BUTTON, and push the TEST BUTTON.

@ = When the data has been cleared, “COMPLETED”

will be displayed. Bring the arrow to “NO” and press the TEST BUTTON to cause the MENU mode to return on to the screen.

@ Note that the contents of the GAME SETTING, SELECT WITH SERVICE BUTTON COIN SETTING, and BOARD SETTING are not

LOmess es BeTONTOyyaffected by BACKUP DATA CLEAR operation.

FIG. 7.16 BACKUP DATA CLEAR,

Page 34

8 . HANDLEBAR

‘ARNING! W a or short circuit accident. @ In order to prevent an electric shock and short circuit, be sure to turn power off before performing work by touching the interior parts of the product. @ Be careful so as not to damage wirings. Damaged wiring can cause an electric shock

8 - 1 ADJUSTING/REPLACING THE FRONT BRAKE VOLUME

In the test mode, if the Front Brake Volume’s Value movements are irregular, adjust or replace the Volume by using the following procedure: Take out the 4 screws and remove the VR cover.

The Front Brake Volume is inside the VR cover.

VOLUME ADJUSTMENT

Move the VR Bracket to disengage the gear mesh. GICIOKOIC)

SCREW (4)

VOLUME ADJUSTMENT

Replace the Volume if it is malfunctioning. Install the Volume in the manner so that 20+/-5

is indicated when force is not exerted.

Remove the 2 screws which secure the VR iS) Bracket. @ Remove the Volume Gear from the Volume Shaft and remove the Volume from the VR

Bracket to replace the volume. @ After the replacement, be sure to perform the Volume setting in the Test Mode. Loosen the 2 screws which secure the VR bracket to move the VR Bracket.

By adjusting gear mesh, fasten the 2 screws which secure VR Bracket. Move the Brake Lever fully to the movable range and check if the Volume Shaft’s revolvable range is exceeded. After adjustment, be sure to perform the Volume setting in the Test Mode.

VOLUME

220-5484

VR BRACKET

Page 35

8 - 2 ADJUSTING/REPLACING THE ACCELERATOR VOLUME

In the test mode, if the Front Brake Volume’s Value movements are irregular, adjust or replace the Volume by

using the following procedure:

Take out the 4 screws and remove the VR cover.

The Front Brake Volume is inside the VR cover.

VOLUME ADJUSTMENT

® Loosen the 2 screws which secure the VR bracket to move the VR Bracket.

@ Move the VR Bracket to disengage the gear mesh.

(6) By adjusting gear mesh, fasten the 2

screws which secure VR Bracket.

® Move the Brake Lever fully to the movable range and check if the Volume Shaft’s

revolvable range is exceeded. M4x8 ® After adjustment, be sure to perform the

Volume setting in the Test Mode. ACCELERATOR GRIP

VOLUME ADJUSTMENT

Replace the Volume if it is malfunctioning.

Install the Volume in the manner so that 20+/-5

is indicated when force is not exerted.

® Remove the 2 screws which secure the VR Bracket.

@ Remove the Volume Gear from the Volume Shaft and remove the Volume from the VR

Bracket to replace the volume.

©) After the replacement, be sure to perform the

Volume setting in the Test Mode.

VOLUME 220-5484

SCREW (1)

M4x8 ACCELERATOR VR BRACKET

Page 36

8 - 3 ADJUSTING/REPLACING THE HANDLEBAR VOLUME

In the Test Mode, if the HandleBar Volume’s value movements are irregular, adjust or replace the Volume.

® Remove the 4 s

TRUSS SCREW (4)

MAx8 (black)

CONNECTORS

@ Disconnect the 3 connectors and remove

the mask cover.

When the mask cover is removed, monitor

screen adjustment knob appears.

ADJUSTMENT KNOB

Page 37
  • Remove the bolt w/hexagon hole and pull out the handle from the shaft.

Bolt w/hexagon hole M10x20, w/flat and spring washers

® Take out the 3 screws, disconnect the connector inside the tank, and remove the tank.

CONNECTOR

8P YELLOW

i “= ude a

a

a

Page 38

SCREW (1) M4x8, w/ flat and spring washers

©) Remove the 4 hexagon nuts which secure the centering mecha. By viewing the centering mecha from above, remove the hexagon nuts from the four corners only.

HEXAGON NUT (4) M8

w/ flat and spring washers

© Carefully lift the centering m a and disconnect

the connector connected to the centering mecha.

} ae mm

Page 39

V.R. ADJUSTMENT

Gror Do not touch places other than those specified. Touching placers not specified can cause an electric shock and /or short circuit accident.

IMPORTANT!

® Loosen the 2 screws which secure the V.R. Bracket to move the V.R. Bracket. @ Move the V.R. Bracket to disengage ADJUST GEAR mesh and move the V.R. shaft in the SCREW (2) VR. SHAFT manner so that the V.R. shaft cut portion faces yy4xg the oppisite side of ADJUST GEAR as shown. Have the gears meshed and tighten the 2 ADJUST GEAR iC) screws. ® Carefully turn the Handle Shaft to left/right and check to ensure the value variation is

within the mobile range of the Volume. © After finishing adjustments, be sure to perform Volume Setting in Test Mode. VE. BRACKET

V.R. REPLACEMENT

SCREW (2) 0) Take out the 2 screws which secure the Volume

Bracket to remove the Volume Bracket.

@ Remove the Volume Gear fromt he V.R. to replace the V.R.

® After the replacement, perform Volume Setting in the Test Mode.

HANDLE VR.

Page 40

8-4 GREASING

Be sure to use the designated grease. Using undesignated grease can cause parts damage. Do not apply greasing to places other than those specified. Greasing to undesignated

IMPORTANT! places can cause malfunctioning and the quanlitative deterioration of parts.

Once every three months, apply greasing to the following places. For Greasing use Grease Mate (P.No. 090-0066).

GEAR MESH PORTION

(FRONT VR.) GEAR MESH PORTION

(ACCELERATOR)

SLIDING FACE OF BRAKE

GEAR MESH PORTION

(FRONT V.R.)

Page 41
  • FOOT BRAKE MECHA

In order to prevent an electric shock and short circuit, be sure to turn power off before performing work by touching the interior parts of the product. Be careful so as not to damage wirings. Damaged wiring can cause an electric

WARNING! shock or short circuit accident. Do not touch places other than those specified. Touching places not specified can cause an electric shock or short circuit accident.

9-1 ADJUSTING AND REPLACING THE VOLUME

In the Test Mode, if the Rear Brake’s (Foot Brake’s) volume movements are irregular, adjust or replace the Volume by using the following procedure.

® Remove the 6 screws.

@ Disconnect the connector, and remove the Foot Brake Mecha from the cabinet.

TRUSS SCREW (6) M6x16, chrome CONNECTOR

WHITE 4P

FOOT BRAKE MECHA

TRUSS SCREW (6) M6x16, chrome

Page 42

V.R. ADJUSTMENT

©

2)

i)

® Loosen the 2 screws which secure the V.R.

Plate to move the VR. Plate.

Move the VR. Plate to disengage ADJUST GEAR mesh and move the V.R. shaft and

ensure that when force is not exerted on the

pedal, the cut face of the Volume Shaft faces in the direction shown.

Have the gears meshed and tighten the 2 screws. At this time, tighten gear backlash. Carefully move pedal fully within the movable range and check if the Volume range is

exceeded.

After finishing adjustments, be sure to perform Volume Setting in Test Mode.

V.R. REPLACEMENT

0)

@ Take out the 2 screws which secure the Volume

Plate to remove the Volume Plate.

Remove the Volume Gear from the V.R. to

replace the V.R. After the replacement, perform Volume Setting in the Test Mode. SCREW (2) M4x8, w/flat and spring washers V.R. SHAFT

V.R. PLATE

O}| \ aprusT GEAR

Page 43

9 - 2 GREASING

S

IMPORTANT! Be sure to use the designated grease. Using undesignated grease can cause parts damage. Do not apply greasing to places other than those specified. Greasing to undesignated places can cause malfunctioning and the quanlitative deterioration of parts.

Once every three months, apply greasing to the following places. For Greasing use Grease Mate (P.No. 090-0066).

GEAR MESH PORTION

SLIDING FACE OF SPRING AND SHAFT

Page 44

10 .COIN SELECTOR

HANDLING THE COIN JAM

to see that the selector correctly functions.

CLEANING THE COIN SELECTOR

The coin selector should be cleaned once every 3 months. When cleaning, follow the procedure below: (@) Turn the power for the machine OFF. Open the coin chute door. Open the gate and dust off by using a soft brush (made of wool, etc.). @ Remove and cleen smears by using a soft cloth dipped in water or diluted chemical detergent and then squeezed dry. (@) Remove the CRADLE. When removing the retaining ring(Ering), be very careful so as not to bend the shaft. ©) Remove stain from the shaft and pillow portions by wiping off with a soft cloth, etc. ©) After wiping as per #5 above, further apply a dry cloth, etc. to cause the coin selector to dry completely. FIG.9b

@ Never apply machine oil, etc. to the coin selector @ After cleaning the Coin Selecting,

IMPORTANT! Insert a regular coin in the normal

working status and ensure that the Selector correctly functions. ©

@

Insert a coin

COIN INSERTION TEST Mii

Once a month, when performing the COIN SW Button pressed TEST, simultaneously check the following: down and check if it is + + ye rejected. O Does the Coin Meter count satisfactorily? 7 O Does the coin drop into the Cashbox correctly? COIN METER

O Is the coin rejected when inserted while keeping

the REJECT BUTTON is pressed down? FIG. 9c

4l If the coin is not rejected when the REJECT BUTTON is pressed, open the coin chute door and open the selector gate. After removing the jammed coin, put a normal coin in and check

Page 45

OPTIONAL DOLLAR BILL ACCEPTOR

@ THE COIN DOOR ASSEMBLY USED ON HARLEY DAVIDSON U/R COMES EQUIPPED TO ACCEPT A DOLLAR BILL ACCEPTOR. ALL NEEDED WIRING CONNECTIONS ARE CONVIENENTLY LOCATED INSIDE THE GAME FOR THIS APPLICATION.

@ THE COIN DOOR CAN ACCCOMMODATE THE FOLLOWING VALIDATORS:

HOLE POSITION#1 Mars 2000 series (FORWARD-MOST POSITION)

HOLE POSITION#2 Mars 2000 series DBV45 (JCM)

HOLE POSITION #3 CURRENTLY NOT USED

HOLE POSITION #4 DsI01*

*The back flange on the chute can be removed for hold position #4. If the flange is not removed, it may interfere with the back of the cabinent.

The frame and cashbox enclosure on this coindoor has been modified to accomodate a Mars 2000 series upstacker. A 2000 series stacker can be added by simply removing the top two entry door and replacing it with a one entry door with a cut-out for a stacker. This one entry door can be ordered through Coin Controls or one of Coin Controls autherized distributors. The part number is 91-4000-01. The Mars stacker can be obtained through an autherized Mars distibutor.

Page 46

CjO|TN| |C O|N|T/R/O|L|S G OVER/UNDER TWO

riRIN)al tENTRYCOINDOOR*

1850 HOWARD ST., ELK GROVE 1L 60007 (847) 228-1810

+ MARS SERIES 2000 UPSTACKER ADAPTABLE

PART #DESCRIPTIONCOSTPART #DESCRIPTIONCOSTPART #DESCRIPTIONCOST
1) I2-4060-KX $-10 ACCEPTOR19.5016) 91-{109-16 RRUBCT PLAP AYLOK, BLACK = 2.7028) 23-L0UL-00 L270 ABTER8.50
[4150-011 S-7 US 8.252.0017) H-ALN3-O1BNTRY/REJECT BUTTON 25e44523-03-00 4.57 OC WBTER3.50
2) AHITT+0 PLASTIC CASBBOX7.4018) S1-L117-00 LAMPHOLDER1.402%) 90-1032-01 ABTER & LOCKOUT SCREE)
3) 20-4189-00—NCLOSTRE, 2200027.5019) 91-1121-00 B/R BUTTON SPRINGA30) 22-1400-00 LOCKING BAR7.00
4) 90-1002-00 HINGE SCRETP]20) SI-1118-00 GV LAMP TEDGE BASEMhSLY Q0-4018-00 3/4" LOCKTASHBRB
5) 90-1003-00 CLAMP SCRET42U) M1-1311-16 BUTTON BRZEL BLACK2.70
6) 90-1017-00 SCREV BRZEL NYLON&2) M-1312-16 BRJECT BEZEL BLACK2.70
7) 9-1206-02 H-40 KEP AUP3B23) 91-2125-00 12¥ LOCKOUT COLL ASSEMBLY12.85
8) 90-1300-00 KEYHOOK324) St-2216-16 MICROSTITCH ASSEMBLY6.00|
9) 91-0508-16 FRAME30.002A) QI-LEL6-16 MICROSFITCE BLACK5.40
10) 91-0506-00 CLANPAbSE-ALIG-LL MICROSELTCH WRITE5.40
$1) 91-0547-00 DOUBLE D Call LOCK5.2SH-LL16-10 MICROSEETCH RED5.40
12) 91-0603-16 BLACK MINT DOOR5.40248) $1-1125-00 MICROSRETCH PLASTIC COVERtb
13) 91-0604-16 2 ENTRY UPPER DOOR10.002%) 92-1002-01COIN INLET LAP SIDE1.80
14) 91-4008-099 LOCKOUT BRACKET4.3026) $2-1002-021 COIN INLET COVER SIDE1.80
15) 91-1008-107 RASEPLATE ASSENBLY5.0027) 92-1002-10 HOLD DOWN BRACKET1.50

JAN. 1998 FORM 92-1003-05

Page 47

11 . MONITOR

When performing such work as installing and removing the monitor, inserting and disconnecting the external connectors to and from monitor, be sure to disconnect the power connector (plug) before starting work. Proceeding the work without following this instruction can cause electric shock of malfunctioning. Using the monitor by converting it without obtaining a prior permission is not allowed. SEGA shall not be liable for any malfunctioning and accident caused by said conversion.

Primary side and secondary side The monitor’s circuit which is divided into the Primary side and secondary side, is electrically isolated. Do not touch the primary side and the secondary side simultaneously. Failing to observe the instruction can cause electric shock, and this is very dangerous. SECONDARY SIDE When making monitor adjustments, use a non- (Chassis, CRT) conductive driver and make adjustment without touching any other part other than the Adjustment V.R. and Knob. Also, be sure not to cause a shortcircuit to the Primary side and the Secondary side. If short-circuited, it can cause electric shock or malfunctioning, which is very dangerous.

High tension Voltage Some of the parts inside the monitor are subject to high-tension voltage in excess of 20,000 volts and very dangerous. Therefore, do not touch the monitor interior. Should soldering & paper wastes, etc. be mixed in the monitor, turn the power off so as not to cause malfunctioning or fire hazard.

() ANODE CAP PRIMARY SIDE DEMAGNETIZER REAR PART

IL ANODE LEAD |_MAIN BD Approx. 29 kV DEMAGNETIZER| ) @® FOCUS LEAD COIL (black), Approx. 10 kV

SECONDARY SIDE a FBT Approx.

(Chassis, sheet metal work, CRT, etc.) & Disconnect or unplug 29kV

Connecting the CRT and PCB For combining the CRT and PCB, use the specified part No. to maintain the status of adjustments made at the factory. The anode of the CRT itself will be accumulitavly charged as time elapses, generating high tension voltage which is very dangerous. The monitor should be used with the Chassis, CRT and PCB assembled. When repair, etc. is required at the time of malfunctioning, be sure to send it in an “as assembled” condition. If these are dissassembled, what’s charged to said high tension voltage can be discharged, cuasing a very hazardous situation. Therefore, under no circumstances should it be dissasembled.

Static Electricity Touching the CRT surface sometimes cuases you to slightly feel electricity. this is because the CRT surfaces are subject to static and will not adversly affect the human body. Installation and removal Ensure that the Magnetizer Coil, FBT (Fly-Back Transformer), Anode Lead and Focus Lead are not positioned close to the sheet metal work’s sharp edges, etc. and avoid damaging the insulated portions so as no to cause an electric shock and malfunctioning. (For the name of parts, refer to the above figures.)

Page 48
CAUTION! For the purpose of static prevention, special coating is applied to the CRT face of this product. To protect the coating, pay attention to the following points. Damaging the coating film can cause electric shock to the customers. For the caution to be heeded when clearing, refer to the Section of Periodic inspection Table. Do not apply or rub with a hard item (a rod with pointed edge, pen, etc.) to or on C.R.T. surfaces. Avoid applying stoickers, seals, etc. on the C.R.T. face. Do not remove aluminum foils from the C.R.T. corners. Removing the aluminum foils can cause static prevention effects to be lowered. Aluminum Foil
Page 49

NANAO monitor: 200—5242-—2 4—0 4 (24K mode)

S| Bgl °

® © i o i Oooo

SANWA monitor: 200-5 2 43-2 4 (24K mode)

ooaagsa

ORONO CHORCEOMOROM®

RGAIN GGAIN BGAIN BRIGHT HSIZE HHOLD HPOS! VSIZE VHOLD VPOSI

iS) z Qa z Zz

G-GAIN ......... Controls colors.

B-GAIN

BRIGHT........... Controls screen brightness.

H. SIZE .......... Controls horizontal screen size.

H. HOLD.......... Provides horizontal synchronization, i.e., controls right/left hold.

H. POSI........... Controls horizontal display position on screen.

V. SIZE .....s000+ Controls vertical screen size.

V. HOLD......... Provides vertical synchronization, i.e., controls up-down hold.

V. POST ......s0000 Controls vertical display position on screen. BOOQEVLOOHOH CONTRAST.... Adjusts image contrast.

Page 50

12 . REPLACEMENT OF FLUORESCENT LAMP AND LAMPS

@ When performing the work, be sure to turn power off. Working with power on can cause an electric shock or short circuit accident. @ The Flourescent Lamp, when it gets hot, can cause burns. Be very careful when replacing the Fluorescent Lamp.

To perform work safely and securely, be sure to prepare a step which is in a secure and stable condition. Not using a step or using an unstable step can cause a violent falling down accidents.

CAUTION!

12 -1 REPLACEMENT OF FLUORESCENT LAMP

® Take off the 3 screws which secure the Holder on the upper part of Billboard.

@ Take out the billboard from the cabinet and replace the fluorescent lamp (20W)

TRUSS HEAD SCREW (3) ost x M4X12, BLA \ — —x0 a, 12, BLACK’ vi =L ay

ro ot CO a®) DESIGN PLATE LEADER

LAMP_110V_25W 390-5573

Page 51

12-2 REPLACING THE LAMP

® Take out the screw to remove the lamp from the lamp body.

LAMP 24V_20W 390-5754

Page 52
  • PERIODIC INSPECTION TABLE The items listed below require periodic check and maintenance to retain the performance of this machine and ensure safe operation.

@ Be sure to check once a year to see if Power Cords are damaged, the plug is securley inserted, dust is accumulated between the Socket Outlet and the Power Plug, etc. Using the product with

WARNING! dust as is accumulated can cause a fire or electrical shock. @ Periodically once a year, request the place of contact herin stated or the Distributer, etc. where the product was purchased from, as regards the interior cleaning. Using the product with dust as is

accumulated in the interior without cleaning can cause a fire or

accident. Note that cleaning the interior parts can be performed on a pay-basis.

ITEMS DESCRIPTION PERIOD REFERENCE BIKE MECHA Volume V.R. inspection Monthly 7,8

Greasing to gears and springs | Monthly 8

Memory Test Monthly 7 Setting Check Monthly 7

BRAKE MECHA SW Volume inspection Monthly 7,8

Greasing to gears and springs [Tri-monthly | 8

Check Volume Value. Monthly 7

COIN SELECTORCheck COIN SWMonthl7

COIN SELECTOR cleaning __| Trimonthly 10

PROJECTORScreen cleaningWeeklyll
Check adjustments.Monthly4,7, 11
GAME BDSetting checkMonthly7
INTERIORCleaningAnnuallysee above.

POWER PLUG Inspection and cleaning

CABINET SURFACESCleaningAs necessary | see below

(CLEANING CABINET SURFACES

If the cabinet is badly stained, use a cloth which is dipped in the chemical detergent liquid diluted with water and then suezzed dry. Do not use thinner, benzine, alcohol or chemical dustcloth as these can damage Cabinet surfaces.

Page 53
  • TROUBLESHOOTING Should trouble occur, first check connector connections.

PROBLEMS CAUSE COUNTERMEASURES

With Main SW ON, no activation Power is not supplied.

Power supply/voltage is not correct.

AC main fuse causes the power to be cut off due to momentary overload. Plug in correctly

Make sure that power supply/voltage is correct. Check fuse. Remove the cause of overload and replace fuse

Operation is unsatisfactory Volume Setting Failure

Poor mesh of V.R. gear.

Spring failure due to secular change of Accelerator and brake mecha. Perform Volume setting Adjust or replace V.R.

Adjust Gear mesh..

Replace the Spring.

Irregular sound emitted from inside Rear Cabinet Greasing to gear mesh portion is not satisfactory, or extraneous matter mixed in. Apply greasing or eliminate extraneous matter.

The color of the image on PROJ. screen is incorrect. Connector connections are defective. Check the connection for the RGB and SYNC connectors of the PROJ. TERM. BD and VPM BUFFER BD.

The image on PROJ. screen has color deviation. Affected by the magnetic field of installation location. Make CONVERGENCE adjustment. (Refer to Section 9.)

No sound is emitted. Sound Volume adjustment is not appropriate.

Sound BD and speaker are malfunctioning. Adjust sound volume. (see Section 6).

Perform sound test to find and replace defective parts.(Refer to Section 6).

NETWORK check will not finish. Communication cable’s connection failure. Perform VR. setting, Adjustment.

Communication play is not possible. Communication cable’s connection failure. Communication Play setting is wrong. Check for Communication cable disconnection Correctly set in test mode.

No sound from Vibration Mecha. In correct Cabinet Type Setting. Correct Cabinet Type Setting.

The Fluorescent lamp does not light up. The Fluorescent tube is burnt out. Replace the Fluorescent tube (Refer to Section 10).

Shift operation is not is not satisfactory in Manual transmission. Shift SW malfunctioning. Replace SW

Page 54

14 - 1 REPLACEMENT OF FUSE

WARNING! @ !n order to prevent an electric shock, be sure to turn power off before performing work by touching the interior parts of the product. @ Be careful so as not to damage wirings. Damaged wiring can cause an electric shock or short circiut accident @ After eliminating the cause of the blowing of fuse, replace the fuse. Depending on the cause of the fuse blowing, using the fuse as is blown can cause generation of heat resulting in fire.

Take out the truss screws and remove the back door to replace fuse.

Truss Screw (2) Black

Page 55

15 . GAME BOARD

WARNING!
CAUTION!

@ In order to prevent an electrical shock, be sure to turn power off before

performing work by touching the interior parts of the product. @ Be careful so as not to damage wirings. Damaged wiring can cause an electric shock or short circuit accident.

Do not expose the Game BD, etc. without a good reason. In this product, setting changes are made during the test mode. The Game BD need not be operated. Use the Game BD, etc. as is with the same setting made at the time of shipment.

REMOVING THE GAME BOARD

Remove the 2 screws which secure the Front Door.

the Cabinet

Disconnect all of the connectors connected to the Shield Case. (Blue 2P, Black 4P, Black 6P, White 8P, Black 10P, Black 12P, Red 12P, Blue 12P) 15-1

@) Unlock and remove the Front Door from

Screw (2)

M4x30, flat washer used

52,

Page 56

® Remove the truss screws fromthe wooden base on which the Shield Case is mounted.

© Withdraw the base from the cabinet together with the Shield Case as is mounted.

SHIELD CASE

© Remove the 3 screws, take out the Shield Case Lid and the Game Board will appear.

SCREW (3)

SHIELD CASE LID

Page 57

15 -2 COMPOSITION OF GAME BOARD

GAME BD HARLEY DAVIDSON (833-13325) SCREW (16) M3x55, flat and spring washers used SCREW (1)

JUMPER SETTING (@CPU BD)

ROM BD HARLEY DAVIDSON (834-13326) [Oo [e) fe} [e) fe) ToT ROT = OEacnosa7 tas Tear wranoo1 Tey ierowai | (ie? ero MPR-20378 MeR=20361_ | PMPR-20362

[ieze waa,Texs rootTes exawon | [rea icrowoorzl-2irle
MPR-20379MPR-20360wen=20363_|pren-2o36e | 198198 ]a5 8
MPR~20381MPR~20382wer-20365 | pMPR-20366 | Jog leg |aa laa
Tes ROOTTesE Wace)ver rerun)Tee (cronio)Erg od bed ed
MPR-20383MPR-20384MPR-20367_ | (MPR-20368
Teas RuTERE WRONO)ves tera | [reroverowaasof

MPR-20385 MPR-20386

‘eae omcTeronTevvrenonany | (ievziereazorwl uo
MPR-20387MPR-20368eek

iO ‘eae mows) Tenmonn | O Ceneroan | Caveman | |85|3S

MPR-20389MPR-20390Epr-z0409_|(ePR-20410 | |89|8%
Teco ROTea fonerersenoan | Crereteromy | [5/5
MPR-20391MPR-20392EPR-20411 | PEPR-20412 | LIES

SEGA

DESCRIPTION

MODEL3 STEP2 VIDEO BOARD 834-13326 ROM BD HARLEY DAVIDSON 837-11861-91 MODEL3 COMM BD COM

NOTE: THIS PICTURE IS FOR REFERENCE ONLY!! UNIT IS NOT TO BE OPENED. EXPOSING THE GAME BD FOR ANY REASON MAY VOID WARRANTY.
Page 58
  • COMMUNICATION PLAY
WARNING! Before performing between-cabinets connection work, be sure to turn the Power SW OFF and unplug the power plug from the wall socket. Failure to observe this can cause electric shock and/or short circuit accidents. Perform assembling as shown in this manual. Erroneous assembling can cause electric shock accidents and malfunctioning.

By linking 4 machines, up to 4 persons can play simultaneously. Although accessory parts are to be installed for communication play, some of the parts will remain as spares.

16 - 1 INSTALLATION PRECAUTIONS ye

(0) Simplemultiple machines are to be linked, sufficient

power corresponding to the number of machines used i

need to be supplied. As standard, amperage is 7A Ex (AC100~110~120V area).

between machines is 20 cm. If parts are not installed, adjascent players will come nto contact with each other Due to the parts used for communication play, interval APPROXIMATELY 0.2m j

and this can cause accidents and trouble.

16 - 2 CONNECTING THE COMMUNICATION CABLES,

S

IMPORTANT! The Communication Cable is optic-fiber made and will break if excessively bent. Handle with care.

Connect machines with the protective tube and pass the communication cable in the tube. Depending on the number of machine units to be linked, connect the communication cables (optic-fiber cables) in a manner shown in the following figures.

Page 59

® Take out the 2 screws and remove the Back Door.

TRUSS SCREW (2) Black

TRUSS SCREW (4) Black

Page 60

(©) Loosen the screw and turn the Fiber Lid so as to After securing Connector 29, secure Fiber Lid with the screw. install Connector 29 to the Fiber Lid Base. Take

out the nut from Connector 29 and insert Connec-

tor 29 into the Fiber Lid Base hole, then fasten the

nut to secure.

® Insert Protective Tube to Connec-

tor 29. With a click sound, the tube

is secured to the connector.

CONNECTOR 29

® Pass the communication cable through the Protective Tube.

Page 61

© Reinstall Fiber Lid to the original position.

@ Take out the 2 screws, unlock and remove the Front Door, and the Shield Case appears. the communica-

tion cable insertion connector is with the Filter Board

in front of the Shield Case. Take off the Cap from the connector and insert the communication cable.

Page 62

EXAMPLE OF HOW CABINETS SHOULD BE SET UP FOR COMMUNICATION PLAY

Page 63

Loosen the hexagon bolt on the side where the machine for communication play is to be installed.

Install joint parts used to join interactive play machines together. ® Loosen the hexagon bolt on the lower rear of the cabinet. Loosen the hexagon bolt onthe side where machines are to be linked for communication play.

® Insert the notch portion of the lower joint to the loosened hexagon bolt and retighten the hexagon bolt.

Page 64

LOOSENED HEXAGON BOLT

As in the rear of the cabinet, loosen the hexagon bolt of the side where the lower joint in front of the cabinet is to be installed.

@) __ Insert the Joint Plate’s notch portion to the loosened hexagon bolt and retighten the hexagon bolt. At this : . . JOINT PLATE time, align the Joint Plate’s hole and the lower joint’s screw hole, then retighten the hexagonal bolt. Align the hole positions.

@ Secure the joint Plate and Lower Joint with the 2 hexagon bolts.

ea

od

HEXAGON BOLT (2) Black s t 7 M6x12, nna i w/flat & spring washers ~

Page 65

e) Remove the Shipping Hook Align to the cabinet side board.

Bracket from the side where the \, UPPER JOINT Joint Parts are to be installed.

SHIPPING HOOK BRACKET

Secure the Upper joint by using the 2 hexagon bolts which secured the Shipping Hook Bracket.

HEXAGON BOLT (2) M8 X30, w/flat & spring washers

Remove the 2 screws out of a total of 4 screws, which secure the a Lamp Holder, from the rear side and utilize these to install the POP

HOLDER.

POP HOLDER

TRUSS SCREW (2) chrome M4 Xx 16

Page 66

In the similiar manner shown as on the previous page, connect the communication cable for the other machine and install joint parts.

@ By using 2-sided tape, install the POP PANEL to the POP HOLDER installed for the adjoining machines.

POP PANEL POP HOLDER (Adhere with 2-sided tape)

o

Page 67

16 - 3 SETTING FOR COMMUNICATION PLAY

S

IMPORTANT! During communication play, if communication is interrupted due to a certain cause, ERROR MESSAGE will be displayed, then NETWORK check mode appears on the screen automatically.

Cause all of the seats to enter the Test Mode and change the NETWORK ASSIGNMENTS of each seat for communication play. For the Changing procedure, refer to the explanations of Section 7.

® Press the TEST button to enter the test mode and choose “NETWORK ASSIGNMENTS”.

@ Bring the arrow to COMMUNICATION and select “NETWORK”.

©) Bring the arrow to PRIVILEGE MODE and press the Test Button to set one of the plural seats (basically the leftmost seat) to “MASTER”. Set other seats to “SLAVE”

® Bring the arrow mark to “CABINET ID NUMBER”, press the TEST BUTTON and set the seat number of the machines sequentially to No. 1, No. 2, No. 3, No. 4 as applicable starting from the extreme left facing the monitor’s front side. If the same number is for 2 or more cabinets, or if the sequential order is incorrect, the game display, etc. will be confused (different from the actual status). Therefore, be careful of this point.

In the case of communication play, all the settings other than CABINET TYPE, B.G.M. VOLUME, and ENGINE VOLUME from among the Game Assignments will be executed by the MASTER SEAT. All other seats (“SLAVE”) are subject to the setting change made by the “MASTER” seat.

Va NETWORK ASSIGNMENTS

COMMUNICATION NETWORK

When COMMUNICATION PRIVILEGE MODE MASTER : CABINET ID NUMBER 1 is set to STAND ALONE, >EXIT these are not displayed

SELECT WITH SERVICE BUTTON

AND PRESS TEST BUTTON,

Page 68

16 - 4 NETWORK CHECK

With the communication play setting, NETWORK check is executed when the power is turned on or the test mode is exited.

CHECKING NETWORK (SLAVE) During the network check, the screen shown right

will be displayed. If communication play setting andNETWORK BOARDDETECTED
communication cable connection are correct, theDOWN LOADSUCCESS
Game mode (the ADVERTISE MODE) isNETWORK BOARD RAMGOOD

displayedand the network check is finished.

PLEASE WAIT

CHECKING NETWORK (MASTER)

If communication play setting error or communica-

tion cable error is found, the screen shown rightNETWORK BOARDDETECTED

appears. Press the TEST BUTTON to enter the TEST DOWN LOAD SUCCESS

MODE. Check and correct the communication playNETWORK BOARD RAMGOOD

setting. Check communication cable connection by

watching. OTHER BOARD NOT READY

OR

NETWORK CABLE ERROR,

During communication play, if communication is interupted due to a certain cause, the screen shown right will appear and then, network check starts . NETWORK ERROR automatically. In the network check, if an irregularity such as the communication cable diconnection is detected, the screen shown right appears.

Page 69
  • DESIGN RELATED PARTS

ITEM NO. PART NO.

4230-0318-91 HLDO-1110X HLDO-1111X 4220-0654 4220-0655-91 4220-0656-91 HLDO-1117 HLDO-1118 HLDO-1104-A HLDO-1104-BX HLDO-1082-B HLDO-1082-C HLDO-1082-DX HLDO-1082-EX HLDO0-3055-B HLDO0-3055-C HLDO-3051-CX 4210-9747 DESCRIPTION

BILLBOARD PLATE HLD STD STICKER CABIL STICKER CABIR PLAY INSTR HLD STD A PLAY INSTR HLD STD B SUB INSTR HLD STD STICKER CABI FRONT L STICKER CABI FRONT R STICKER MASK COVER L STICKER MASK COVER R STICKER FUEL TANK A STICKER FUEL TANK B STICKER TANK L STICKER TANK R STICKER REAR FENDER L. STICKER REAR FENDER R STICKER BAR AND SHIELD STICKER HLD CUP

Page 70
  • PARTS LIST

TOP ASSY HARLEY-DAVIDSON STD

Page 71

TOP ASSY HARLEY-DAVIDSON STD

ITEM NO

wns yaw PART NO.

HLD-10001 HLD-3050 DYN-O011 422-0654 422-0655-01-91 422-0656-91 DESCRIPTION

ASSY CABINET ASSY SEAT CABI DENOMI PLATE W/O ORIGINAL PLAY INSTR HLD STD A PLAY INSTR HLD STD B ENG SUB INSTR HLD STD

Page 72

ASSY CABINET (HLD-10001)

Page 73

ASSY CABINET (HLD-10001)

ITEM NO. PART NO.

HLD-1100 HLD-1080 HLD-1090 DYN-1080 HLD-2000 HLD-2800 HLD-4700 HLD-4500 HLD-4600 MIT-3650 HLD-1103 HLD-1104 HLD-1105 HLD-1106 HLD-1107 HLD-1108 HLD-1109 GBN-1076 TTR-1067X 117-5235 MITS5-3603 MITS-3612 HLD-1116 HLD-1130 423-0318-91 MIT-3005 253-5366 HLD-1126 HLD-1127 200-5243-24 280-5112 280-5113 280-5114 130-5152 3901-5753 280-5185-15 DESCRIPTION

ASSY SUBCABI STD ASYY FUEL TANK SW UNIT AC UNIT ASSY HANDLE ASSY FOOT BRAKE MECHA ASSY MAIN BD STD ASSY ELEC ASSY POWER SUPPLY ASSY CENTERING MECHA MASK HOLDER LOWER MASK COVER SASH LOWER SASH UPPER LAMP HOLDER LAMP FRAME SP BRKT MASK SUPPORT MONITOR MASK PLATE 6-30 MOUNT BLOCK HANDLE HOLDER TANK BASE ASSY FL BILLBOARD PLATE HLD STD. CALLAR CASH BOX GUARD PLATE CUSHION ASSY CLR DSPL 29 TYPE 24K 100V BUSH FOR TV COLLAR FOR TV SPACER 6.4-25X2 SPKR BOX MINI DOME ASSY LAMP 24V 20W SPACER TUBE L=5

Page 74

ASSY SUB CABI STD (HLD-1100)

)

OPPOSITE SIDE

Q®

Page 75

ASSY SUB CABI STD (HLD-1100)

ITEM NO.

101 SEE DESCRIPTION PART NO.

HLD-1101 HLD-1102 GBN-1074X HLD-1110X HLD-1111X HLD-1120 117-5098 117-5235 105-5169 105-5171 HLD-1112 DP-1167 HN-1042X 253-5396-91 HLD-1113 HLD-1114 HLD-1115 HLD-1117 HLD-1118 HLD-1119 HLD-1122 HLD-1123 HLD-1124 HLD-1125

260-0011-02 220-5412 DESCRIPTION

WOODEN CABINET BACK DOOR MONITOR SUPPORT STICKER CABI L STICKER CABIR ASSY FRONT DOOR TNG RETAINER PLATE PLATE 6-30 LOCK BRKT W CHUTE PLATE SINGLE METER BRKT TNG LKG FAN BRKT CABINET HANDLE JOINT HOLDER FOOT REST STEP RUBBER STICKER CABI FRONT L STICKER CABI FRONT R FIBER LID BASE FIBER LID FOOT COVER A FOOT COVER B FOOT COVER C ASSY COIN DOOR AXIAL FLOW FAN AC 100V 60-60Hz MAG CNTR W/CONN

Page 76

ASSY FRONT DOOR (HLD-1120)

ITEM NO. PART NO. DESCRIPTION

1 HLD-1121 FRONT DOOR 2 DP-1148X LKG TNG 3 117-0062 PLATE LOCK RETAINER 101 220-5575 CAM LOCK MASTER W/O KEY

Page 77

ASSY FUEL TANK (HLD-1080)

ITEM NO. PART NO.

HLD-1082 509-0161 509-5779-RE 509-5779-YE DESCRIPTION

FUEL TANK SW PB TYPE 1T YEL W LAMP. SW PB W/LAMP 6V RED SW PB W/LAMP 6V YELLOW

Page 78

ASSY FL (HLD-1130)

tO

ITEM NO. PART NO. DESCRIPTION

1 HLD-1131 FL BASE 101 390-5538-20SD ASSY FL20W SD W/CONN HIGH L.

Page 79

SW UNIT (HLD-1090)

eye) iO | «és VOLIFRONT | VOLSEAT 7 | <5 TEST SW SERVICE SW DEMAG. SW. ikem o «

ITEM NO. (103)

PART NO. DESCRIPTION

1HLD-1091W PLAT!

101 220-5179 VOL CONT B-5K OHM

102601-0042KNOB 22M
103509-5028SW PB 1M
Page 80

AC UNIT (HLD-1095)

ITEM NO. PART NO. DESCRIPTION

1 DYN-1081 AC BRACKET 101 280-0417 TERMINAL BINDING POST BLACK 102 509-5453-H-B SW ROCKER J8 H-B 103 280-5134-6N4 BUSHING STRAIN RELIEF 105 514-5030-91 FUSE HOLDER 106 LOCAL PURCHASE FUSE 5A SLO 107 117-5225 TERMINAL PLATE 3P 20A

Page 81

ASSY HANDLE (HLD-2000)

ITEM NO. PART NO. DESCRIPTION

1HLD-2001HANDLE BAR
2HLD-2002GRIP LEFT
3HLD-2500ASSY BRAKE MECHA
4HLD-2600ASSY THROTTLE
5HLD-2700ASSY SHIFT SWITCH
6HLD-2003PLATE PROTECT TUBE
Page 82

ASSY BRAKE MECHA (HLD-2500)

AND COMO

© GOO OG

  • @)
Page 83

ASSY BRAKE MECHA (HLD-2500)

ITEM NO. PART NO.

HLD-2501 HLD-2502 HLD-2503 HLD-2504 HLD-2505 HLD-2506 HLD-2507 HLD-2508 HLD-2509 HLD-2510 HLD-2511 HLD-2512 HLD-2513 HLD-2514 601-10023 HLD-2004 220-5484 601-7944 000-T00408-0B 050-C00400-3B 000-P00408-W 030—000620-SB 028-A00306-P FAS-500015 065-S016H0-Z 065-F00600-0B DESCRIPTION

BRAKE MASTER CASE MASTER CASE HOLDER MASTER CASE COVER BRAKE GEAR IDOL GEAR PIVOT SHAFT VR BRKT LEVER STOPPER IDOL GEAR SHAFT MASTER PISTON END CAP BRAKE LEVER VR COVER RETURN SPRING PROTECT TUBE TUBE WSHR VOL CONT B-5K OHM GEAR 15 M SCR TH BLK M4X8 CAP NUT TYPE 3 BLK M4 M SCR PH W/FS M4X8 HEX BLT W/S BLK M6X20 SET SCR HEX SKT CUP P M3X6 CAP NUT BLK M6 STP RING BLK OZ M16 FLT WSHR BLK M6

Page 84

ASSY THROTTLE (HLD-2600)

APPLY GREASING TO GEAR PORTIONS.

Page 85

ASSY THROTTLE (HLD-2600)

ITEM NO.

wn OI AH

ll PART NO.

HLD-2601 HLD-2602 HLD-2603 HLD-2604 HLD-2605 HLD-2606 HLD-2607 HLD-2608 HLD-2609 HLD-2610 HLD-2611 HLD-2612 601-10023 HLD-2613 HLD-2614 HLD-2004 220-5484 601-7944 000-T00408-0B 000-P00408-W 000-F00408 030-000625-SB 060-F00600-0B 028-A00306-P 012-P00306 DESCRIPTION

THROTTLE CASE LOWER THROTTLE CASE UPPER INNER GRIP ACCEL GEAR BASE PLATE ACCEL GEAR SHAFT ACCEL VR BRKT SPRING HOOK RETURN SPRING VR COVER ACCEL GRIP SLIDE PLATE PROTECT TUBE SPRING STOPPER GEAR SPRING TUBE WSHR VOL CONT B-5K OHM GEAR 15 M SCR TH BLK M4X8 M SCR PH W/FS M4X8 M SCR FH M4x8 HEX BLT FLT WSHR BLK M6 SET SCR HEX SKT CUP P M3X6 TAP SCR #2 PH 3X6

Page 86

ASSY SHIFT SWITCH (HLD-2700)

ITEM NO. PART NO. DESCRIPTION

1HLD-2701SWITCH CASE

2 421-7752 STICKER UP DOWN 3 601-10024-01 PROTECT TUBE EX S

4HLD-2004TUBE WSHR

101 509-5003 SW PB TYPE IT GREEN 14.2

102509-5003-03PB SW RED
Page 87

(20520 GI (06) (202) (13) GREASING,

LZ) (207) (Q2\(203\ (202 CREF) DOBBS ASSY CENTERING MECHA (MIJT-3650)

Page 88

ASSY CENTERING MECHA (MIJT-3650)

ITEM NO. PART NO.

MIJT-3651 MIT-3652 MIT-3653 MIT-3654 MIT-3655 MIT-3656 MIT-3657 MIT-3658 MIT-3659 TTR-2010 601-6555 601-6450 RDY-2106 100-5096 100-5043 601-8847 220-5484 050-F00600 060-F00800 060-S00800 050-H00800 030-000612-S 060-F00600 000-P00408-W 060-F01200 060-S01200 050-H01200 028-A00410-P DESCRIPTION

MAIN SHAFT STOPPER COLLAR B MACHA CASE A MECHA CASEB LOSTA HOLDER HOLDER VR HOLDER SHAFT GEAR HOLDER 110 GEAR Z=30 M=0.75 GEAR 110 VR BRACKET BEARING 17 BEARING 25 FYH SBP FL 205 LOSTA DR-S-18X30 VOL CONT B-5K OHM FLG NUT M6 FLT WSHR M8 SPR WSHR M8 HEX NUT M8 HEX BLT W/S M6X12 FLT WSHR M6 MSCR PH W/FS M4X12 FLT WSHR M12 SPR WSHR M12 HEX NUT M12 SET SCR HEX SKT CUP P M4X10

Page 89

ASSY FOOT BRAKE MECHA (HLD-2800) © -

Page 90

ASSY FOOT BRAKE MECHA (HLD-2800)

ITEM NO.

SBIYDHAAWNH PART NO.

HLD-2801 HLD-2802 HLD-2803 HLD-2805 HLD-2805 HLD-2806 HLD-2807 HLD-2808 POW-2613 HLD-2809 220-5484 601-7944 601-6450 000-P00412-W 000-P00408-W 028-C00308-P 050-U00600 060-F00600 050-U00800 060-F00800 DESCRIPTION

PEDAL PLATE PEDAL BRKT BRAKE PEDAL PEDAL SHAFT TORSION SPRING STOPPER RUBBER UPPER STOPPER RUBBER LOWER RUBBER HOLDER VR PLATE PROTECT PLATE VOL CONT B-5K OHM GEAR 15 GEAR 110 M SCR PH W/FS M4X12 M SCR PH W/FS M4X8 SET SCT CH CUP P M3X8 U NUT M6 FLT WSHR M6 U NUT M8 FLT WSHR M8

Page 91

ASSY MAIN BD STD (HLD-4700)

\e @ @

rg)

°

gi]

° H

co} ® &

;

  • (3) 4 oy

ITEM NO. PART NO. DESCRIPTION

1 HLD-4400 ASSY SHIELD CASE 2 HLD-4701 WOODEN BASE MAIN BD 3 105-5241 SHIELD CASE BRKT

Page 92

ASSY SHIELD CASE (HLD-4400)

101)

tot

ITEM NO.

Skune PART NO.

105-5240Y 105-5242X 839-0932 833-13325 260-0064 DESCRIPTION

SHIELD CASE MODEL 3 SHILED CASE LID MODEL 3 FILTER BD MODEL 3 SPG GAME BD HARLEY-DAVIDSON FAN MOTOR DC 12V

Page 93

ASSY ELEC (HLD-4500)

QS

S

YZ ZY

Z

101) (1)

ITEM NO. PART NO. DESCRIPTION

1HLD-4501WOODEN BASE ELEC
2BY-4102FAN MOTOR BRACKET
3838-13142BASS AMP 50WX2
4838-11650-36EQ. PWR AMP HLD STD
101400-5330-02-91SW REGU FOR MODEL 3

102 260-0011-02 AXIAL FLOW FAN AC100V 50-60HZ

103280-0419HARNESS LUG
Page 94

ASSY POWER SUPPLY (HLD-4600)

ITEM NO. PART NO.

HLD-4601 838-11856-01 839-1011-01 560-5380 LOCAL PURCHASE DESCRIPTION

WOODEN BASE PWR SUPPLY CONNECT BD W/FUSE & COVER SSR 1EA BD BR AUDIO XFMR 12.8V 6A 23V 9.6AX2 FUSE 5A SLO

Page 95

ASSY SEAT CABI (HLD-3050)

@Y &) @)

ei

Page 96

ASSY SEAT CABI (HLD-3050)

ITEM NO. PART NO. DESCRIPTION

1HLD-3051SEAT CABINET
2HLD-3052MAINTENACE LID
3HLD-3053EX PIPEL
4HLD-3054EX PIPER
5HLD-3055REAR FENDER
7HLD-3057JOINT FRAME
8HLD-3058FENDER STAY
9.HLD-3059JOINT LID
10HLD-3600ASSY VIBRATOR
201000-T00408-0BM SCR TH BLK M4X8
202000-T00416-0BM SCR TH BLK M4X16
203000-T00425-0BM SCR TH BLK M4X25
204000-T00412-0CM SCR TH CRM M4X12
205000-T00425-0CM SCR TH CRM M4X25
206030-000820-SBHEX BLT W/S BLK M8X20
207030-000860-SBHEX BLT W/S BLK M8X60
208068-441616-0BFLT WSHR BLK 4.4-16X1.6
209068-44 1616-0CFLT WSHR CRM 4.4-16X1.6
210060-F00800-0BFLT WSHR BLK M8
211050-U00600U NUT M6
212068-652016FLT WSHR 6.5-20X1.6
Page 97

ASSY VIBRATOR (HLD-3600)

ITEM NO. PART NO.

HLD-3601 130-5172 050-U00400 060-F00400 DESCRIPTION

MOUNT PLATE BASS SHAKER U NUT M4 FLT WSHR M4

Page 98

Come see Sega GameWorks Service Department’s Homepage

fedaaetsste bot oh

ericeee a tne ee st Do oT Pere | Pee ee es fmt on eee ie oe i OS es GN SS SE PD Pa Pel Mee Se ee ee oe pm ce ee om fo alee oo go: cell om 1 LL es PE at a a

ay Se Komen oop coms om = Lae a

Page 99

SEGA

SEGA ENTERPRISES, INC. (USA)

45133 Industrial Drive Fremont, CA 94538 415/650-802-1750 phone 415/650-802-1754 fax