CATHODE RAY TOMES

Blasto

Blasto (Gremlin, 1978) · Manual · 75 pages · 56 sections · original scan

Page 1

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 2

BLASTO

OPERATING INSTRUCTIONS

AND

SERVICE MANUAL

GREMLIN INDUSTRIES, INC, 8401 Aero Drive San Diego, CA, 92123

Page 3

BLASTO

TABLE OF CONTENTS

INTRODUCTION

IMPORTANT NOTE

REPACKAGING INSTRUCTIONS

GAME CONCEPT & OPERATION

SYSTEM DESCRIPTION

SYSTEM BLOCK DIAGRAM

CHARACTER GENERATION CIRCUITRY DIAGRAM

TONE GENERATOR DIAGRAM

MAINTENANCE

KEY WAVE FORMS DIAGRAM

CHARACTER CODE TABLES

RECOMMENDED SPARE PARTS LIST

SCHEMATICS PAGE

op WN HP

1l

Page 4

INTRODUCTION

This is an electronic game that makes extensive use of digital integrated circuitry and television monitor circuitry. This manual assumes the maintenance technician possesses a general knowledge of solid state circuitry microprocessor, TTL digital integrated circuitry and T.V. monitor concepts. Any individual NOT knowledgeable in these areas SHOULD NOT attempt repair of the electronic portion of this game. IT SHOULD BE NOTED THAT ANY ATTEMPT TO REPAIR THE GAME IN THE FIELD WITHOUT THE EXPRESS CONSENT OF THE FACTORY WiLL IMMEDI- ATELY VOID THE WARRANTY!!!

IMPORTANT NOTES:

NEVER replace any components with anything other than exact replacement parts. (See Parts List located on Service Schematics.)

NEVER remove circuit boards/connections while power is on.

DO NOT replace the fuse with anything other than the proper value. A blown fuse indicates an overload condition within the game. Replacing the fuse with a higher value can cause severe damage to internal components if an overload occurs.

ALWAYS consult the manual before attempting repairs.

CORRESPONDENCE regarding this game should be addressed to:

GREMLIN INDUSTRIES, INC. 8401 Aero Drive

San Diego, California 92123

(714) 277-8700 ‘

-l1-

Page 5
IMPORTANT NOTE

An important service note is posted in this game and is repeated here for emphasis:

IF AT ANY TIME THE T.V, SCREEN SHOWS A MEANINGLESS DISPLAY OR THE GAME OTHERWISE MALFUNCTIONS, SIMPLY DROP A COIN INTO THE COIN MECHANISM. THIS SHOULD COR- RECT THE PROBLEM, IF NOT, THE GAME REQUIRES SERVICE.

The circuitry in this game has been arranged so that the insertion of a quarter through the coin mechanism will reset the restart in the system. This clears up temporary problems caused by power line disturbances, static, etc.

SERVICE TECHNICIAN NOTE:

The system reset circuitry described above requires that the coin counter is attached to the system. If there is a coin counter problem and no replacement is available, the game will function properly if a 10K Ohm resistor is connected across the coin counter input pins to the video logic board.

Page 6

REPACKAGING INSTRUCTIONS

Should it be necessary to ship this game, the following instructions are provided for game crating:

COCKTAIL VERSION:

  • Turn game upside down, taking care to protect the game top and player keys.
  • Attach pallet to game bottom with two 1/4"-20 x 1-3/4" bolts, as shown:
  • See Final Recrating Instructions, below.

STAND-AROUND VERSION:

  • Turn game upside down.
  • Attach pallet with two 5/16"-18 x 3" bolts, as shown:
  • See Final Recrating Instructions, below.

ARCADE VERSION:

  • Carefully lay game on its side.
  • Attach pallet with four 5/16"-18 x 1-3/4" bolts, as shown:

3, See Final Recrating Instructions, below,

FINAL RECRATING INSTRUCTIONS:

Place game upright. Tape down game keys. Then, crate the game using appropriate shock-absorbent packing material, Include padding on edges of game. SECURE PACKAGE WITH STRAPPING,

NOTE: If the game is to be shipped to Gremlin Industries for service or repair, attach a tag identifying the distributor and indicate the service or repair to be done; include the full serial number of the game.
Page 7

GAME CONCEPT & OPERATION

BLASTO is a two player video game in which opponents compete for high score. The game is available in two versions--a sitdown or standaround table version, and an arcade upright style version. Electronically, the two versions are nearly identical. This manual is intended to describe both versions.

Each player is provided with a set of controls to maneuver a spaceship, and launch a Gremmaray from the spaceship. In the sitdown version, these controls are four direction buttons, and a center mounted FIRE button, In the upright version, a four-position joystick assembly and fire button are used for each player.

The spaceships are highly mobile. The response to the motion controls has been carefully "tuned" for maximum response to the player's actions. Tapping a direction control moves the ship instantly in that direction. Holding a direction control down produces a quick "single step" motion, automatically followed by rapid continuous motion across the screen, This gives the players good control of the spaceships.

The playfield is arranged as a maze of small squares, with patterns of mines randomly interspersed. The mine pattern is different for every game played (the general maze pattern is always the same), Each player has a SCORE indication,

SCORING:

There are three ways to score. Hitting any of the squares which form the maze scores one point (sitdown version) or ten points (upright). Hitting a mine scores five points (sitdown) or fifty points (upright). Hitting the opponent scores 100 points (sitdown) or 1000 points (upright).

MINES:

(NOTE; Numbers in ( ) are values for the upright version.) Whenever a mine is hit, the player who hit it scores as the mine explodes (accompanied by a loud boom sound), Additionally, the exploding mine explodes everything adjacent to the mine. This includes squares, additional mines, or one of the spaceships if it has the misfortune of being next to an exploding mine. This makes several very interesting shots possible. Two examples: A player who runs up next to a mine and explodes it scores 5 (50) for the mine, but then blows up his spaceship (from the mine explosion) which scores 100 (1000) for the opponent. Also, if a long chain reaction of mines is touched off by hitting one of a series of adjacent mines, and a player's ship is next to any of the mines as they go off, he is blown up and the other player scores 100 (1000) points.

The score values are arranged so that players can enjoy the game at many levels. Beginners

Page 8

GAME CONCEPT & OPERATION: (Cont'd.)

MINES; (Cont'd.)

will usually play to hit the most mines, and ignore the 100 (1000) point "kill shot". As it is discovered that it is much more profitable to hit the opponent, the game takes on a renewed frenzy. Anytime a player is hit, he must hit the opponent to get back into the game. This type of balance at all skill levels insures a long playing history for BLASTO.

Whenever a player's spaceship is hit, it rapidly spins around (accompanied by a humorous spinning sound), and then explodes, awarding the opponent 100 (1000) points. Whenever this happens, both players are reset to their starting positions.

GAME TIME,

When a coin is accepted, the game timer is set to 90 seconds, and ticks down to zero for the end of the game. An internal jumper is provided to make the beginning time 60 seconds (see cable harness drawing),

ADVERTISING:

When the game is not in play, an advertising sequence continuously plays. The words "GAME OVER" appear in the screen center, and the two spaceships randomly move and fire. The scores from the previous game are retained during advertising, A switch inside the coin door allows the spaceship "spinning" sound, which occurs anytime a space= ship is hit, to be switched on or off during advertising.

GAME ADJUSTMENTS:

The E-Z Adjust ™ control panel, mounted on the rear of the cash box, provides two ad-

justments:

  • Volume control. Set to desired sound during game play. This game is a sonic spectacular, So set this as loud as you can stand; the sounds alone will really attract players. .
  • Advertising sound. Switches the spaceship "spinning" sound on or off during advertising. When the game starts, all sounds are automatically switched on.

FREE GAMES:

The upright version of BLASTO allows free games. As shipped from the factory, the free game feature is connected. YOU MUST DISCONNECT THE FREE GAME FEATURE IF

Page 9

GAME CONCEPT & OPERATION: (Cont'd.)

FREE GAMES: (Cont'd.)

IT IS ILLEGAL IN YOUR AREA, To do this, simply remove the back from the game, and cut the wire loop at the rear of the video logic board (betwen pins 33 and 34), After you have done this, the game starts as follows:

When a credit is accepted, the screen clears, and the message PRESS START appears onthe screen. If the SINGLE PLAYER START button is pressed, the message "HIT ALL MINES FOR FREE GAME" appears for about five seconds; then the screen clears, the playfield sets up, and the game starts. It is not possible to win two free games in a row (no free games on a free game). When a free game is won, either a single player or two player game may be played.

Free games are awarded only for single player games.

STARTING THE GAME: (Sitdown version only.)

Inserting a coin starts the game. The playfield from the advertising sequence is cleared from the screen, a new playfield is built, and the player spaceships are placed at their starting positions. The spaceships alternately flash (accompanied by a random beeping sound) to indicate that the game is ready to play. As soon as any of the player buttons is pushed, the game starts. ~

STARTING THE GAME: (Upright version only.)

If the multiple coin option is implemented, inserting the first coin clears the screen. The game then waits for the proper number of coins to be inserted. For the single coin game (standard version), inserting a coin clears the playfield and displays the message "PRESS START". The player now has the option of playing a single player or two player game.

Note that the single player high score is always displayed at the bottom of the screen. This provides a powerful incentive to the single player.

Pressing SINGLE PLAYER START begins the game. With free games enabled, the game starts after briefly displaying the message "HIT ALL MINES FOR FREE GAME",

OPTIONS:

Both versions allow the game time to be shortened to 60 seconds. In addition, the following options apply to the upright (arcade) version only:

  • The number of coins for a game credit may be changed from one to two, three to four. Refer to the proper harness drawing at the rear of this manual.
  • The wire loop at the rear of the logic board (between pins 33 and 34) should be

«6-

Page 10

GAME CONCEPT & OPERATION: (Cont'd.)

OPTIONS: (Cont'd.)

left intact to enable free games. FREE GAMES ARE HIGHLY RECOMMENDED, Our earning reports show that this will significantly improve and prolong the earnings for the game.

Page 11

SYSTEM DESCRIPTION

SEE SYSTEM BLOCK DIAGRAM

MICROPROCESSOR -

The game microprocessor is a Model 8080A and it functions as the Central Processing Unit (CPU) in the system. The CPU (1) is synchronized by a clock circuit which provides frequencies required by the CPU and the Video Timing Logic (14).

Address Bus (4) selects the memory addresses to be accessed by the CPU. It is routed to three subsystems:

1. Read Write Memory (6): A random Access Memory (Ram) used to form a first in/last out (stack) memory. Used to perform subroutine calls and returns, also used for temporary data storage during program execution.

Read Only Memory (Rom) (7): Stores program instructions for the CPU.

Address Multiplexer (8); Selects either CPU addresses or addresses from the Video Timing Logic. Used to address the Video Refresh Memory (9).

Data Bus (5) carries data to and from the CPU. It receives data from Read Write Memory, Read Only Memory, Video Refresh Memory and Input Ports (12). The Bus transmits data to Read Write Memory, Output Ports and Video Refresh Memory. The Input Ports accept player control data (19). The Output Port (13) initiates sound control and activates any external logic and indicators needed by the game.

Timing and Control Logic (11) generates synchronizing signals to keep system operation synchronized to the CPU. It controls:

1. PWN Memory Read Memory Write Input Port Read Output Port Write

Page 12

SYSTEM DESCRIPTION: (Cont'd.)

MICROPROCESSOR - (Cont'd.)

The remaining elements in the System Block Diagram convert (CPU) system information into a video display format. The T.V. monitor (18) uses a standard 525 scanline system.

Video Refresh Memory (9) stores information from the CPU which is read out as the CRT beam sweeps across the screen. It is addressed from two sources as controlled by Address Multiplexer (8). During vertical sweep retrace of the CRT, the Video Refresh Memory is addressed by the CPU so information can be updated. During scan time, Video Refresh Memory is addressed by Video Timing Logic (14). Refresh Memory Control (10) insures that address demands from Video Timing Logic and the CPU never occur simultaneously.

Character Generator Memory (15) provides a means for Video Refresh Memory to select 64 dots for each 8 word access. Each image, onthe display, will have the dimensions of 8 dots high, and 8 dots wide. Shift register (16) develops this into a video signal. (Page 12.)

A tone Generator is driven by Output Ports (13), The CPU controls the frequency of the tone by loading a number (0-255) into the Output Ports (13). A direction change by a player will cause the CPU to load a different number into the Output Port, changing the tone. (Page 13.)

Page 13

VIDEO TIMING

LOGIC

address bus 4

CPU menory | | CRT beam

address

ADDRESS MULTIPLEXER] 8

CPU 8030A

v y

READ- 6 READ- 7 REFRESH

WRITE ONLY MEMORY MEMORY MEMORY CONTROL | data bus (8 lines)

VIDEO REFRESH WEMORY READ-WRI TE)

CHARACTER GENERATOR MEMO Timing & [1+ CONTROL

ready SYSTEM BLOCK DIAGRAM

mem R mem W input strobe output strobe

12 | outeut| +3 PORTS player controls +v sound indicators

position addr.

RY (READ- ONLY

sync & blanking

Page 14

VIDEO

REFRESH

MEMORY

ADDRESS~

FROM

ADDRESS

MULTI PLEXOR

CHARACTER

GENERATION CIRCUITRY DIAGRAM

MEMORY INPUT DATA FROM MICROPROCESSOR DATA BUS

1024 «8 1

ok a lout_out out out out out out out

haracter EIGHT ieeege™ OUTPUTS 256 x 8 TO SHIFT

REGISTER D7 D6 BS hy

2v lv

OCHrHNDAN AY & WwW

Page 15

a MICROPROCESSOR syste

OUTPUT STROBE

b4 p> p6 oD/

LATCH

(e.6, 7475)

(E.G, 7475) PRESET_COUNTER (e.6. 74163) LPP tea.

(E.G.

TONE GENERATOR DIAGRAM

OUTPUT

Page 16

MAINTENANCE

FACTORY ASSISTANCE:

TECHNICAL HELP 1S AVAILABLE FROM THE GREMLIN

FACTORY. IF A PROBLEM OCCURS WHICH CANNOT BE

EASILY RESOLVED BY YOUR DISTRIBUTOR, A PHONE CALL OR LETTER TO THE FACTORY WILL BRING ATTEN-

TION TO YOUR PROBLEM BY A TRAINED REPRESENTATIVE.

NOTE: IF AT ANY TIME THE T.V. SCREEN SHOWS A MEANINGLESS DISPLAY OR THE GAME OTHERWISE MALFUNCTIONS, DROP A COIN IN THE COIN MECHANISM, THIS SHOULD CORRECT THE PROBLEM. IF NOT, THE GAME REQUIRES SERVICE.

EQUIPMENT: THE FOLLOWING IS A RECOMMENDED LIST FOR ANYONE ATTEMPTING TO SERVICE THIS GAME

  • Oscilliscope - 50 Mhz or wider band width
  • DVM (Digital Volt Meter)

OHM Meter

  • Logic Probe
  • Solder Station - in most cases a digital IC can only take about 300* of heat for 10 seconds. (a 75 watt soldering iron is much higher), Recommended wattage should be 40 watts or less.
  • Jumpers
  • Replacement parts including game programs, see Recommended Spare Parts List, page 23.
Page 17

1.

2. MAINTENANCE PROCEDURES: (Cont'd.)

POWER SUPPLY MALFUNCTION:

Remove Output Connectors

Initial Tests: (GND lead to C-18 negative terminal located off board.)

+9 at "+" of C-18

+19v at C-6 (4700 mfd)

-19v at C-5 (4700 mfd)

-12v at pin 11

+12v at pin 12

+5v at pins 18-20

zero v (GND) at pins 14-16

If adjustments are required, attach meter ground to pins 14, 15 or 16 or equivalent local ground and:

a. +5v adjust - input lead to pins 18, 19, 20 and adjust R-9 for +5.0 to +5.1.VDC.

+12v adjust - input lead to pin 12 and.adjust R-10 for +11.5 to +12.1VDC.

-12v adjust - input lead to pin 11 and adjust R-10 for -11.5 to -12.1 VDC

If initial test is good, attach output connectors to Video Logic Board. Repeat Step 2.

a. If readings differ from those previously taken, a loading problem exists on the Video Logic Board.

No -12VDC or 5VDC on the Video Logic Board: (Power Supply Normal)

Video Logic Board Schematic (VLBS) (SH. 2). CHECK U-65, C-29 for open/short. CHECK R-40, C-12, .D-2 (VLBS) (SH. 1).

Page 18

MAINTENANCE PROCEDURES: (Cont'd.)

POWER SUPPLY MALFUNCTION: (Cont'd.)

No +12VDC at CPU: (Power Supply Normal)

(VLBS) (SH. 2). CHECK U-65, C-28. (VLBS) (SH. 1) CHECK C-23, C-25,

VIDEO LOGIC BOARD MALFUNCTION:

No P1, #2 CLOCKS: (Ref. Fig. 4A)

(VLBS, (SH. 1). CHECK U-32 pins 1 and 3 for 20.79 MHZ. CHECK U-31 pins 14, 13, 12, and 11 for 150 nsec sinewave. CHECK U-17 pins 1, 3, 4, and 10, CHECK latch network U-18 and U-8. CHECK high voltage outputs of U-30 pins 3 and 6. If not present, remove driver transis tor. Should U-30 now show output, replace driver transistor, if still not present replace U-30. U-45 could load down 21 clock.

No Coin Start:

(VLBS) (SH. 1) CHECK output U-9 pin 6. If signal not present, lift U-10 pin 5. Should signal return, replace U-10. If still not present, check output of U-8 pin 3. CHECK D-8 pull up diode and C-18, CHECK U-14, U-32 could be shorting signal to Q, and Q,-

Screen Flashes: (Similar to COIN START clear)

Power Interrupt Board bad (Q-3, U-2). Wires on coin box leading to Antenna of power Interrupt are intermittent. Wires on +VAC from power supply open/intermittent. Power Interrupt Board not secure on TP3 and TP4.

No Coin Meter Action:

(LBS) (SH. 1) Signal from U-8 pin 11 feeds current limiter R-27 toQ,.

Saturated Q, turns high current transistor Q.. Eight Q, or Q, faulty, wit

ane 5 4 5 inhibit meter.

No Player Control:

(LBS) (SH. 1) Input accepted through U-12 and U-13 via data lines when strobe IND2 signal is generated through U-18 from U-45 and U-51 (status latch), CHECK U-18 pin 11, U-45 pin 8, U-45 pin 11, U-51 pin 10 for strobe pulse.

Page 19

MAINTENANCE PROCEDURES: (Cont'd.)

V!DEO LOGIC BOARD MALFUNCTION: (Cont'd.)

No Game Time Select:

(VLBS) (SH. 1). Input accepted through U-10 and U-11 via data lines when strobe IND1 signal is generated through U-18 from U-45 and U-51. CHECK U-18 pin 3, U-45 pin 8, U-45 pin 11, U-51 pin 10 for strobe pulse.

Meaningless Display on Screen: (Inserting coin does not correct problem)

Possible areas:

  • A program malfunction

a. Check ROM sockets, U-2, U-3, U-4 and U-5.

b. Power Interrupt Board bad (Q-3, U-2)

c. Power Interrupt Board not properly secure on TP3 and TP4.

  • A data transfer malfunction

a. Test the CPU Data Bus by ensuring proper voltage levels. Pullup resistors are used to make memory outputs compatible with the 8080A. High State Logic on the Data Bus should be 3.3v minimum. For involved problems in this area contact GREMLIN INDUSTRIES,

Characters on Screen not correct: (Wrong image behaves normally)

(VLBS) (SH, 2). Use character generator code table to isolate possible bad RAM (U-35, U-36, U-37, U-38, U-39, U-40, U-41, or U-42). Also probable are U-22, U-23 (data buffers), U-24, U-25, U-26 (raultiplexers), U-29 and U-43 (character Proms) and U-49 (shift register).

No Video: (Ref. Fig. 4B, 4C, 4D)

(VLBS) (SH. 2) CHECK U-54, U-53 circuitry for H reset. U-52 pin 1, clock for horizontal scan, U-55, U-58 provides timing for vertical blanking.

Page 20

MAINTENANCE PROCEDURES: (Cont'd.)

VIDEO LOGIC BOARD MALFUNCTION: (Cont'd.)

Bad Video:

(VLBS) (SH. 2) Bad video could be vertical roll or horizontal sliding. CHECK U-55 pin 12 and U-56 pin 4 of horizontal or vertical generators. CHECK U-63 pins 12 and 13 for vertical and horizontal blanking. U-64 develops sync pulses.

Monitor Malfunction:

Refer to Monitor Service Manual. This manual is included with the game's schematics.

Audio Tones; Sour/None:

(VLBS) (SH. 2). U-68, U-61, U-62, U-66, U-67, U-60 comprise tone generator, Amplifier on Power Supply Board (U-4, Q., Q,,Q,, Q,). Could also be problem area. 3' *8’ “9

Boom; Sour/None:

(VLBS) (SH. 1, SH. 2). D-6,Q_,, Qo, Qa , U-5, Q., Qe, Generates Boom. Amplifier section on Power dpply Board U-4 , Q,, Q,, Qe, QQ), also probable.

Page 21

KEY WAVEFORMS DIAGRAM

p2 240.8 NS . ' | 5 vi H { I t i} 1

© ct H264 H330 C V224 V262

Fl V =1V H Blank ov V Blank ov

H Reset H330 Flv V Reset V262 z1V

Vv 0 ov H272 H288 V238 V248

or <<

Connector Pin 38 #2 V

With connector off 0 V

4 INVERTED HORIZ. DURING V BLANK a

Page 22

CHARACTER CODE TABLE (Sit-Down & Stand-Around Versions)

Ic (u#) Image IC (U#) Image

40 41 42 37 38 39 40 41 42

0 0 Oo|010000 0
0 o l=o 10 0 0 1
0 1 0lad0 10 010 %
o1u+E0 100 2 2. WwW
1 0 0=o 1021 0 A
10 14o 10 10 1 WN
1 10H010602122108
111<o i102 11 N
0 0 0M7o 1210000
0 0 1Go 1 10 01 7
0 1 0A0 1 10 1 0 Ik
o 11Mo 1 10 1 1 (BLeWwUP)
1 0 0E0 1 1 1 0 0 {BLOW UP)
101oOo 1 1 1 0 21. (BLOwUP)
1 10Vvo 11110 he
liuR012221211 al

=19-

Page 23

CHARACTER QODE TABLE

(Sit-Down & Stand-Around Versions)

Ic (u#) Image Ic (U#) Image

37 38 39 40 41 42 37 38 39 40 41 42

1 0 0 0 0 0 (BLANKY 1 10 0 0 0 fo) 10 00 01 € 1 1000 1 1 0 0 0 1 °0 a 2 100 1 «0 N 10 0 0 1.1 > 1 100 i121 Mm 210 0 1°00 y 1 1010 0 + 100 1210 1 fF 21021021 a) 10 0 11 0 H 1 1021 £21 «0 .o 210021211 => 1102121421 N 1 01 00 0 in| 2 12100 0 (va) 10 1 0 1 fa) 1 11001 on 1 0 10 21 0 © 1 1210 100 (BLOWUP) loilo321121 © loll o2i1 (BLOwUP) 101 1 00 © 1 11210 0 (BLOWUP) 101101 1121101 (BLOWUP) 102111 ~°0 a 1 112110 (BLOW UP) l1o2l.i1ia2121 v l1li2.iiu (BLOWUP)

Page 24

Ic (u#)

40 41.

0 0

0 0

ool

1 oo

lo

lou

lou

0 0

a)

0 1

loo

loo

lou

lou

CHARACTER CODE TABLE

( Arcade Version)

Image Ic (U#)

  • 38 «39 «40

@ 0 10.0

(BLANK) 0 10 0

(BLANKY 0 10 0

(BLANK) 0 1 0 0

(BLANKY o 1021 = 0 1021 bl o lol +E o 102

  • o 1 1 0

A o 1 1 0

c o 1 1 0

£ 0 11 0

F o lit

6 0 11.2

H o 121i

L o 12.1 Image

edwunwavynozeer

Y MN oes

(@LOWUP)

(BLOW UP) a i

Page 25

CHARACTER CODE TABLE

(Arcade Version)

Ic (U#) Image IC (U#) Image

37 38 39 40 41 42 37 38 39 40 41 42

1 0 0 0 06 0 (BLANKY 1 1000 0 °

1000021 (BLANK) 1100021 \ 1 0 0 0 1 0 (BLANK) 1 1 06 1 °0 2]

1000 211 (BLAN k) 1 1004121 a 10 0 10 0 (BLAN K) i 1.0 10 0 A

1001021 €-1103210 215
10 0 1 1 4 a1 10211 0o
1002121221 >1 10321ida21d217
1 0 1 0 0 0 ¥1 1 1 0 6 08
1021001 qQ1 121001q
10 10 10 ©1 i 1010(BLOWUP)

10210 121 © 112102121 (BLOWUP)

1 0 1 10 0 (0)1121210 0(BLOW UP)

lo 121201 a 21212101 (BLOW UPS

10 21 2 1 ~°0 €11 21 21 1 «6(BLOW UP)

102 21221 1 >} 21.21.2121 (BLOW UP)

Page 26

RECOMMENDED SPARE PARTS LIST

Per Ten Units

PART NO. QTY.DESCRIPTIONARCADE COCKTAIL/STANDAROUND
130-90011Speaker, 6x9xxX
150-90192Cap.,4700MFD, 25 VxXx
150-90221Cap., 9000MFD, 12 VxXxX
213-90022Socket, 18 pin, dual-in-line XxX
213-90042Socket, 16 pin, dual-in-line XX
220-90081Counter, DigitalxxX
220-90351Lock, Coin DoorXxX
220-90662Coin Mech., singlexXER
240-90062Button, redxX
240-900725 Button, blackxX
240-90092Button, yellowx
240-90905Button, red firex
313-90012IC LM 723xx
313-90042Ic LM 741 EN DIPxxX
314-90012IC NE555 DIPxXx
314-90062Ic 7474xXxX
314-90092Ic 7400xxX
314-90122Ic 7408xXx
314-90172Ic 74125xx
314-90461Ic 74804xXx
315-90141IC 8080A,CPUXx
315-90152IC 2102 RAMxXxX
315-90181IC 2111 RAMxxX
316-90891PROM, U2X
316-90901PROM, U3xX
316-90911PROM, U4Xx
316-90921PROM, U5xX
316-90931PROM, U29xX
316-90941PROM, U43x
316-90951PROM, U2xX
316-90961PROM, U3x
316-90971PROM, U4Xx
316-90981PROM, US~23-xX
Page 27

SPARE PARTS LIST, CONT'D

PART NO.

316-9099

316-9100

390-9009 482-9006

482-9010

482-9011 482-9013

482-9014

482-9015

482-9016

510-9023 510-9041

560-9003 807-9003

807-9012 819-9001

819-9026 QTY.

PPE RR Ro NNN NEN NN HB DESCRIPTION

PROM, U29 PROM, U43 Lamp, #47 Transistor, 2N4403 Transistor, PE 8050 Transistor, MJ 3000 Transistor, TIP 110 Transistor, 2N4401 Transistor, TIP 115 Transistor, TIP 29

Switch Assy., WICO Snap acting switch Transformer #4-10345B Power Supply Assy. Power Interrupt Assy. Video Logic Board Video Logic Board

*** Used in some table models.

~24- ARCADE

ms

ec oe COCKTAIL/STANDAROI” >

Po PS PS PS be PS OS OO

ms PS OPS oP

Page 28

R . RF 252-0028 2 @) ReaD CAB. TOP 2 PLC. \ GHEET 3)

Vans (faVrs ever Cone On 4 2)

|__|220-001[cover cas Boxa
  • 4 TEE NUT, Y4-20 x 2 WAGHER, LOCK .26 I.D. 4 ISCREW, SH MET, <R REC ROUND “0 x.79i4] CAD PLT a
ThauBOLT, HEX 4:20 x Lo LoCAD PLTc

mI +~ 4 IECREW, SH MET, CR RECES POW “By. 75LG] CAO PLT i 250-0063 | LIGHT BRACKET

1293-0018| LIGHT WINDOW

1 140-0006 | PEDESTAL

|__| t250-0099PEIESTAL ADAPTER
’250-0049|GETAINER CLIP
me250-0030__|RETAINER , OOR LATCHiz

z{_| NUT, 10-24, CAO PLT. z WUT, 74-20, CAD PLT.

zUWASHER, FLT, .28 1.0.cAp PLT
2iSCREW, MACH, FLT HO.CR.REC -20x125 [CAD PLT
2]GCREWN, MACH FLT HP CR.REC, “10x |./3thgCAC. PLT:
|[aecREW, GH MAT, END CREEC,“Bx 50 Le. CAD PLT

{| ecARW. SH MET ROND CRREC X.C9 La [CAT PLT. ub 250-0047 | Lock catTtH PLATE Cc \ 220-0023 | Lock Asoy.

VIEWACAf250-0046|[RIENFORCING PLATE

4 SCREW, SH. MET, FLT HO CR. REC, fron os Ar. 2 250-0033 | HINGE 4 Go eS _h 280-0034 | HINGE AZsy

i252-0071[Access DOOR Ase.
bt220-0013 _|casH Box

1 252-002!-| | BASE Asov. Fa Se | otra no.

  • 12 PLACES — [onion ‘ \9 ONT [ex reewze pear we. x20-0025 (29\#) RROD NOTES: ta)
Page 29

View GeG ROTATED 73° CW

SECTION [3 © 13 13.3 — (ger

SECTION IF _-FF

Fare]SesoneowBat_| sermons

a 7 = Whee

  • JUNCTION 80K Assy BOB-0009A REF (COVER NOT SHOWN Foe <LaR/TY)

*

2.15 REF

™. ~@

  • t (PARTS 21ST CONTO Ow SH 3)
1250 - 0090 | CLAMP, STORAGE, RODat
1250-0089 | BRACKET, POTt40)
1250-0097|RoDFS
2SCREW. SHUT MTL, FLT Hb, CROSS BEC /O N35 lS138
éNUT , 8-32, CARB STL, CAD PET37
[-]|WASHER, FLT 472 /.D. CARB SR,CADPLT36
8BOLT, CARRIAGE Ht 8-32 x PI $7q,Cao PLT35

S| |SCREW.SHT MTL RD HO, CROSS FEC, #0“ 75 6,caRé ST, (AOR 24

'CARRIAGE BOLT # 10-24 x 2.016 ,CARB)STL,CA PLT33
[Vy][252-0018| BRACKET, CASH Box32
U|COIN MECHANISM3

Sar | omen vo, + On nesnron PARTS ust seme = industries, a —

eaeTRS,Date
ramT, LopateTOP ASSEMBLY
SEE PARTS LsHE Joon2.37BL A S T 0

kd 719-0001 DO NOT SCME DRAWING seu [peer 2 oF

321

mR

719-000/

Page 30

NO. ¢ OPERATOR — SWITCH PLATE

PLAYER CONTROL Assy P/N 8/9 -0002

212-001@ CONN (REF)

‘SINGLE CONG SHLO WIRE

V/DEO LOGIC BD ASSY P/N B08 ~

212-0016 CONN

@VOLT COIN —— COUNTER P/N 807-001! NO. 2 OPERATOR SWITCH PLATE

LU (COM) om A

Kh MONITOR CHASSIS / / \ a |

BLU (com) buy

FUSE HOLDER

INTERLOCK SWITCH

JUNCTION 80x ASSY P/N BOB-0009 EMI FILTER

WHT \\ ‘ eene 2/2-O000.5 CONN

\ 70 momiToR \ conn BLoek

\ \ \ cre mene oooh Os TO MONITOR TO COIN MECH. TO TRANSFORMER

FOR CONTROL BLOCK ASSY ¢ SPEAKER HOOK-UP SEE SH 2

To TRANSFROMER JUNCTION BOX SCHEMATIC Ne (GRouns) WTERCONNECT HARNESS FIN 807-0006

2/2-001@ CONN (REF)

a alan ag San Deoge, Catiforaée 9228 CABINET WIRING BLASTO

D| | 7/9-OOO/A [scare NONE [seet_3 OF

Page 31

DESCRITION RELEASED

COIN MECH. WRING TYP. FOR FOLLOWING PARTS P/N 220-00: Of COIN MECH) 220 - 0066 [SINGLE US. B/LLARS) 220- 0067/ D008 CASH)

GRN WIRE TO PWR "BOX GND STUD

2 COND SHLO WIRE - CONTROL BLOCK ASSY P/N 808-0007

SPEAKER, OVAL @XK9 7 TO PWR SUPPLY BO R2E F/N 130-O00/

PWR INTERRUPT bby 7 70 TRANSFRMER TERM. 8 PI 807-0012

VIDEO LOGIC BOARD Pi’ 808-00 0} OM 08 00 Or SPEAKER HARNESS ASSY P/N 808-0010

——. POWER SUPPLY ASSY

CONTROL BLOCK _ASSY ¢ SPEAKER HOOK-UP NOMENCLATURE OR DESCRIPTION PARTS UST ioe

= ts 2/2Z-O005 CONN (REF) INTERRUPT Bo. Sone Gremlin Industries, inc. Pmt , San Diage, California 9272 BLK £ SRA 2 + BLANK _ C, | —PLe Ker wur ¢ Ben ae CABINET WIRING BLK SOLDER 70 THs : é BLASTO ENb OF 228 ONLY - [CODE TGENT NO. ORARING NO 719-OCO!

Page 32
87654321

REVISIONS DESCRIPTION Zone [ ire A] er eASED

VIDEO LOGIC Bo.

Poe o® 990000000 ' D enyye aa ) ?

z2|zya\G 2] 3za} Zo 2
\5} 8eg|XS 8gLd4) fe 8
|5eaYAz

Qa d oe Ei 3

——vDCBA
me“TL_—Fire putrons—PLAYER <
g|CONT ROL:
©- 3idtrcon wecn.BUTTONS

Fa ND. OFF OOM’ SW. BLK

:6|PoweR suppiy[ !20V+
\100v @RIBBED¢

TRANSFORMER lo}

o-%z|ov ®
et2|sHieLD O4-@8N

5 om . 8

aleaux1ATSg
> |ewar3

ze J S BOR ff RIBBED

=18I}-—

: ry Fy PLUG

© B © BREAKER nL © Cred < ©

©wonToR GuesI )fe)

ci T9INCH MONITOR 3 ()

ALL DIRECTIONS VIEWED FROM TOP OF GAME AND BOTTOM OF SCREEN "PART OR HOMENCLATURE I SNES WO. Ege PARTS UIST SHIELDED WIRE GREMLIN INDUSTRIES INC. G4o1 AERO OR. SAN DIEGO.CA. 92178] bn ae lance SCHEMATIC pee re ee BLASTO Pp 7 7 CABINET WIRING

AX CONNECT TO PIN 32 FOR 60 SECOND GAMEbrszsaee bereSOE ERT Fs] oRRTOT RO

Asses tttae Bo Bi Ms “MEE ™ aoe —— fel 7/9-O00I|A

NOTES:00 NOT SCALE ORANGSCE NONEseer 5 oF
=76541
Page 33

2 RED 2PLaces

2 PLACES 2 PLACES

SECTION Aca : a ae

KO: REGS

t SCREW SHMTL, CRs RECES. FLT WO, WHO x. 75 “Teceew si MIL CRS RECES RD HB,t¢ x 63 + STUCad PLT] (2. CARB. ST. (AD PLT) aT] cae | iW ee Ed

D

(PARTS e157 con Te ct) SY 2) |

4SCREW.SAT MATL Pa HO PRESS REC. #19 x. ua,caee swe, CAD PLT [24
9Se 7 MT _RD HD. C0055 REC B x|.5OLS, CARB STLOWA232
B“VNUT. 832 CARB STL, CAD PLT22
BWASHER, FLT./72 ., CARB STL, CADax
5BOLT, CARRIAGE #B-32 v5, CARB ST.20] ¢

| COIN MECHANISM 19 \ LOCK ASST a0

3[NUT wi0-24,caR STL,cAb PLTv
2NUT, 4-20 CARB STL,CAD PLT%
leWASHER, FLT .26 1.D..CARB ST.CaD Pt\5

2 SCREN,MACH,CRS RECS FLT Ha 20x 1 Ca STLcao ar| 14 3 SCREW, MACH CRS RECES FLT Hoar 10-24 x | 13 cae sc RY (3 |

250-0049 | RETAINER CLIP, BOOR RETAINER, DOOR LATCH T [rock CATCH REINFORCING PLATE HINGE, TOP rT HINGE ASSY,ACLESS DOOR ACCESS DOOR AssT BASE ASSY

PART OF, IDENAFTIN NO,

TF OF NONAL PART NO 220-0025

NOTES 8 TT 7 ease = . bp eeeniy a A Life TOP ASSEMELY BLASTO

| TW9-O002

GAME] Cri

Page 34

8 7 6 5 i 4 3 2 1 T REVISIONS tec BERRI [cent [arraveo \

  • JUNCTION BOX (PEF) (COVER IT “THIN =F2° thA a= | D ° 1p) ~ ——— .80 REF rm -—— I Z aaa ae

~~ USE EXSTING SCREW Tey \PARTS Lis? Gute ww SH 3) (TEM 7 C

+ = 280-0038 |GL12F /N ASSY 250-009/ | 20D 250-0030 [Cham S7OZAGS, ZOD 250-0089 | BACK ET, PivoT SECTION B s B Gry SCREW, SHT MILB HD. CROSS RECs 1099.75 16,CaRB STL Co OO CARRIAGE BOLT 10-24%20 LG,Caed StL,Cap PLT 220-0016 [cash Box COVER

220-0012 |CASH BOK

TCP ASSEMBLY BLAST O [E> oeKut .38 DA HOLE THRU CApmeT " “F 19 -0002 act DoF LOWER PLATE TO MATLH Gwe PIN.

NOTE
Page 35

FOR 719-0002 CABINET

WIRING DIAGRAMS, SEE

719-0001 SHEETS 3, 4 a5,

Page 36

ame. | PARTS [TITLE Gremlin Industries, Ine. LIST BLASTO- ASOoY TIA- oe GEETS SF THRYUBE DRAWN Ga. SMITA ARE 'D SIZE CHECK fw. De Ye [APPR | LTR| DATE REVISION DESCRIPTION i RELEASED eo FORM NE 901-1500

Page 37

WIP POMLMNOG? NIH1/ ASSS ANOD FIO NVA) ASSY TI2L NAL SPO FD 770°WS VA 070520 NOI1d1IN9S3aa ASSV Ydd ALO ASEY - nee sr | “DU S9p42SNpUL UAUIDAD

Page 38

Gremiin industries, inc. PARTS | TITLE San Biege, California 92123 LIST TE! No| PART NO

QTY PER ASSY

REF DES

BOLT; 8-3: cARRINGE 1'/d'LG BOLT; 10-32 CARRIAGE |9/4'L@ MACH SCR | 8-32 SLOT OVAL HO SER; "BQ SHT. MTL. ROND CRS. REC, SCR; 48 SHTMTL. RD.AD. CRS. REC. SCR; “3 SATMTL. KEX.ND | fale WASHER ; 78 FLAT WASHER: #/0 FLAT WASHER; *8 S/2L/T LOCK WASHER, “/0 SPLIT LOCK 10-32 HEX NUT; 10-32 WING SPACER; 3/6 1.0 x 1/4 LG. POLY BANDING BLACK fax 01S it | & GQ LO Je | [OO SREBSERR SS SRE Sale eeialalyey +

Page 39

250-009 | 280-0285 |

CLIP: SWITCH MOLOING; TRIM LWR. 293- 008/ 250-0004 [390-00 |

LAMP, (8° FLOR i it ox “3 “o zo 2/

° /

  • i
  • /

/

  • /

/ [390-c0/2 [420-0026 [1 [4z0-0080 | / lazo-cosa [2 i[4#Z0-004o | / @0. 001-1501 253-008z [280-00/0 __ | SSS RSOUSSS ee

LAMP, FU FLOR

Page 40

Far sive G) pies

  • PLCS RT ecee oF caper TO EUGE OF GRAPHICS TY? ALL ARounP BETH SIDES REVISIONS DESCRIPTION
Page 41

Tyr (4) CORNERS GREMLIN IND. ING Sal DIEGO, cA.

FRAGILE

HANDLE WITH CARE 3 2 1

REVISIONS =I — = T

H

1 i i t

uP

IND, ING 1, CA.

\ ! Fed bie WANDLE |} CARE 1 I

i

i

Qo] Bent | weNneving no. Oe CeSoRTON. PARTS LIST = omits Ane CHES Gremlin Industries, inc. seer Sam Dioge, Cxtiformes 9923

BLASTO- ASS.

EXT ASSY USED OW [APPLICATION THE [EOE TOENT WO] DRAWING FO, 2 D T\9-O002 ev EAE NOE eet © OF B

719-0003

Page 42

REVISIONS BANCTION

SSY_ WITH WIRE NUT 280-0010 2EA. FLOURESCENT LIGHT FIXTURE 390-0012

819-0027 ™ VIEWED FROM BACK PLAYER CONT. HARNESS 819-0029 ee @ir: CONTROL BLOCK HARNESS 819-0030

COIN MECH. SINGLE 220-0066 2EA. COIN DOOR 250-0285 COIN COUNTER ASSY. 813-0012 VIDEO LOGIC BD. 819-0026 PWR. INTERRUPT BD. 807-0012 -WHT- TWIST ON TO. JUMPER HARNESS POWER SUPPLY IASSY 807-0003

JUMPER HARNESS 807-0006 SPEAKER HARNESS ASSY. 807-0010

SPEAKER. 130-0001

CABINET WIRING

719-0003 BLASTO ARCADE JUNCTION BOX ASSY 807-0009 INTERLOCK SWITCH BLK FUSE

Page 43

xevine pin —<& © —} een —&

sw ud —}> ‘4 ®

KEYING PIN

OFF MUTE SW.

TRANSFORME! POWER SUPPLY 20V ov @ BRAID xen PO

HGFE oc BA PLAYER ° CONTROL-—— BUT TONS

FLUORESCENT ov LIGHT FIX. 390-00/2 2 SHIELD g & -& Fd ry z oO re SMOOTH » “ef ee wd 3 RiBBED.

« E

@ BOTTOM sr eanee. L K 5%. o— 2 PLAYER START IPLAYER START 7)

one¥VIEWED FROMrT

BACKSIDE OF

®CONTROL PANEL.6

4 i) | | IQ INCH MONITOR —_ ° Ui) €

L MONITOR EDGE SHIELDED CABLE

°

PARTS UST RES SInGRRE SESE [EORTC WO GREMLIN INDUSTRIES INC < S : A 840i AERO BR SAN DIEGO, CA. 32!23 RS FOR MORE THAN ONE COIN PER PLAY a _ wins OMe apie SCHEMATIC 2 GND OPEN BL ne LASTO PIN” 16 1S GND — CABINET _WIRING ZY somPeR 11s wae TO PINae FOR TO SECOND GAME +5 SSR CUT THIS WIRE IG DISABLE FREE GAMES wor assy | vee On NOTES. APPLICATION ext NONE

787654!1

[779-0003 |B

Page 44
3'2|1

REVISIONS tow [ue BESCRIPTON onte | nopnove BICERECN b> KB [7-6-7 Cl cr2 713/15 was 25v Bk |yupe |Rxd

D D

¢c ¢c

Zaye pees [CONT MALES ON 31 -S5-caos [eons Mate 1g BIN 1 \_ | 176= cogeal ©. C. BomeD >

jaa= 4a7 pole RST TPle
ar1]482 -oos [xiSTOR TIP US
its1482-0013 | XiSTOR TiP 110

en x1 462-o0le | xistee ahaa aiasGa 2 Cook | xIsTSR SNaaSS [pada Z| 4e1 0006 [DIODE INFI4 Se NAA pa Be 2 | 4B1-0008 | DiObe ZENER IN

ji -Da4 | 481 = 9004 |DIOSE MRSo}
[ex1 [151-oone [ERE SER ICSFSow

Sota Higr20008_ ene. CER. .ocIM Boy

eeeeaseB
BGace10 Soylene. 0S ht
Ieecaca(Ss CallTCAP.CER+ .OIM SOV
cei\Si=itCAP. CER, -| M Sov
C14, C16.21150 =000a | Ene, E OM a5v1)

C1, CnCRLET S| a= 00 S| SAP EOE

ai[as =c04 [BorsSIMMER
a2 418 -Ooes | Por2KTRIMMER
es11473-9081 | RES!zl

Ris Ri Rez BZ [a7 = ior [Res. 10S am

= RI4]472-901021 om bw 3%N
Raa|_|471=clo¢RES, OOK OUM Kw 5%&
=([ari=5a32[Res ase one

Re Ba a [ayiseies [Res low oum ews

—Searizoisz| Regs1.8 6 CaM yey

Rr Ras Rao 3S art= 6272] RES. 27 KUM ew 5

Rsi [a= oatRES. 82K — Ou ew Se

Raven ite Rake] 6 | 471-0102] wes, 1K OnM aw 2%

cary| a7is08e2RES SK OuM Ew 3%
ieT[3a=e50Teas
[Oi Ua Ue[3 [313-0004[1-6 M741 EN
iPART ORNOMENCLATURE
[rem wo.few foot ne noOP eenI

PARTS UST

hepeGREMLIN INDUSTIESINC,

Feacrions Decals anours 8401 AERO DR SAN DIEGO, CA 92123

AapaPOWER SUPPLY/AMP. BOARD| A
| is-ccer wustce |ol jlBLOCKADE
ocite-tiu408-0001 leomotien[NEFSHE] CORETOENT NO [ORAWIG WO
767=Coo! [BLockanedD.§ 807-0002}C

NEXT ASSY USED ON

APPLICATION00_NOT SCALE DRAWINGacax|sates 1 OF

[708 -cce2 [como 7oe@-coos | comeTIONTIA No TN Scar kere: PARTS OVERLAY

2 1

Page 45

r MDA 3500 _ REV & PER ECN @2 WIS als 4 120 V REV C C/,2,7,/3,/5 WAS 25V Har/7 9 tab

i ov SHIELD O———~

560-0003 B NOT ON P.C. BOARD

@ix ce INH Y707 4LMI4IEN ee 2N4403 R33 a () hom > ) Ras aR 27K SIR

Rig C4 100.n +7 l0uf 25V

1N5231

LAST © NO. USED C I9 LAST DNO. USED DQ LAST Q@ NO. USED Q10 LAST R NO. USED R U 3: LAST U NO. USED U 4

IGREMLIN INDUSTRIES INC. 8401 AERO DR. SAN DIEGO, CA. 92123 PTE JT SCHEMATIC

BLOCKADE PWR. SUPPLY erECED

Page 46

GREMLIN INDI SAN DIEGO CA92124 TR Ba UTH g ES Ad [| | a P|

RELEASED

ADDED CAP CLAMP

Page 47

GREMLIN IND INC TITLE

SAN DIEGO CA 92123 ASSY. PWR.SUPPLY

QTY PER ASSY

ne DESCRIPTION | REF oes | ra0- 0018 _| PT [CHASSIS POWER SUPRLY| ——S—~™S rig0-0022 _| J P2i= 0008 | J rai 0007 _| F2n- oo |

{ REFERANCE) [a | | 2 | 3 | | 4 | 5 | 6 | 7 | 8 | 10 | Li | 12] = 13 | 14 | 15 | 16 | 18 | Hq) 20) ry

Page 48

FERED &- S : c (2. STRIP ange [sero xs A WY

}

BLK eS Be 5. —4 7 = 5 —_ Lo 2 mai 8 —————————— Ss ry FN io) WINDOWS UP

H+}1--BLk 6” 4 fe-nee é

ye UNLESS OTHERWISE °

ZA AU. POWER TRANSISTORS TO BE MOUNTED WITH HEAT SINKING PASTE & INSULATING HARDWARE, LAL WIRE TO BE Awe#22

SPECIFIED REF ONLY

REF. ONLY

A J

707-000 1 TRANSFORMER REVISIONS ue DESCRIPTION cate | sorngyeo RELEASED 5-3-7al SP7 : tomiensme

MOLEX CONN

WIRING DIAGRAM

SEE DETACHED PARTS LIST 607-0003

PART OR LOEN TYING. NO. NOMENCLATURE OR ORSERIPTION

race 0 [18-0002 [SLAsTO \Faseecn me" PARTS UST

[BLASTO —_|rmcrow

coMoTION L BLOCKADE

Page 49

bCe 130-30 22s 803-00 {zone | ure]

  • [A [REVISED + REDRAWN PER ECN TSI Ke [eS A] [B| C0ES was “CAPE. IM 750, “amepsat] 277%

170 = 0073 } P.C. BOARD 2Z- OOI7 CONN FEMALE !0 PIN RT ANGLE me

#82- 00/4 TRANS(STOR 2N 4401 482 - D006 TRANSISTOR ZN4402

DiCbE ZENER INS523/ RES. 0K OHM 'iW5%e RES. 470K OHM “2,.W5% RES. 33K O#M !/2W5% RES. 100K OHM “2 W 5% R4, R5 RES. 1K OHM “zWS5%o Ri-R3,RB-F

CAP, F, .22M /00¥ CI c/ CAP. E. 1M S0¥ _IC_TIMER NE555 C2, 03 DIU { +

‘CODE PART OR NOMENCLATURE SENT IDENTIFYING NO. OR DESCRIPTION

TUNCESS OTHERWISE SPECIFIED [CONTRACT NO, DIMENSIONS ARE iN INCHES TOLERANCES ARE. PARTS LIST

DECIMALS ANGLES, xx = XXX

NEXT ASSY USED ON APPLICATION DO _NOT SCALE DRAWING ‘SIZE | CODE IDENT NO. [DRAWING NO. 807 -OO1Z

[seme none Teer on

Page 50

REVISIONS: ZONE, ea E DESCRRTION Al per €=0 731 TP3 Q3 2N440! Ri IK Qz 2N4403 [or GREMLIN INDUSTRIES INC. | avons | me | B¢0/ AERO DR. SAN DIEGO,CA.92125 enone, (2/27)

Ig SCHEMATIC — i POWER INTERRUPT

Page 51

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 52

Parts | Tl Gi Jin industries, Inc.

  • PROM ST2X4F _PROM S/2X4 4lo = ” 48 | 49 | = 50 | 57 | 52]

IS0K OWMS 2W SM R72 22 OHMS Y2W 5% R43,R45 | 220 OHMS Y2W $% F28,R42Z,R54, 2.2K OHMS /2W5% R35 22K OHMS '/2ZW 5% FP 29-R36,RG0 ZZOK OHMS VAW 508 POS 2.7K OHMS (/2WSS, R7B 330 OHMS /2_W 5% R4G,R47,R8I,RBZ | 33K OHMS 72 W 5d P59,R63,RG6,R70_| 330K OHMS VaWS5% RST fA ~

N O}A/0 | S RSSEEERERH

Page 53

0G) BOARD

BLASTO

RS tm]

INFOO02. S “0 4FBl- OOOG IN 914 OR IN4/4B)

ZENER _IN523) 2N 3565 48Z2-0006[/ | 2NF#4O3 482-00/0|1| PE BOSO

2Nt4O! 70 | N ~

Page 54

VIDEO LOGIC BOARD | 819-000/ |sH3 A

DWG NO REV

U1,UI7 U2Z0, U2Z2,U23, 033 pu2z8 Pusey

Page 55

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 56

REVISIONS Zone [er DESCRIPTION

™~

Ne 6 PLACES

2 PLACES

819-0001

wlFae ORNOMENOUATRE
aeeesoe BESERIHON

PARTS LIST, ONLESS OTMERWIGE SPECIFIED [CONTRACT NO DIMENSIONS Ae IN INCHES TOLERANCES ARE: FRACTIONS DECIMALS ANGLES = xe = ‘APPROVALS woe aaTERAL PRAWNT. JOHNSON

L@ 5 PLACES 2 PLACES

Gremiin Industries, inc. San Diegs, Catiternta 92723 A A

  • OMIT Q1.Q2,D,D3,04,U35,U36 CILCSLELE2 PC ASSEMBLY
  • LAST C,NO USED © 52 > JUMPER WIRES AT NOTES _ VIDEO LOGIC BOARD
  • LAST D.NO USED DB 9. CAPAGITANCE VALUES ARE IN MICROFARADS BLASTO
3 LAST QNS UD au.8. RESISTANCE VALUES ARE IN OHMS715-008]SEE [GOSHEN [OIEmE
CAST UNO USED U6S7 ON CONNECTOR PINS 315 273944,46 52,54S57ARE BLANK KE YING PINSZig_0001_|BLASTO_D819-000!

OTES: UNLESS OTHERWISE SPECIFIED APPLICATION DO ROT SCALE DRAWING 8 7 6 5 t 4

Page 57

PEVISIONS:

126 gR2S S24 R73 SRI7QR2 SR20. Rin SPig Ris GRia Bis OR SRi Skee gh SP 1K SK SK SIR STK me IK Sim Sim SK Sm Sim Sim Sie StH

i

i

Uz Us 1ozax4 PROM c) 1o24x4 PROM owe 0034 2 se 0022 . TT

29 gR30 gR3 32 1K S22k HI $722k

READY 4

RESET H 219-0001

WOMENCLATURE Of DESCRIPTION PARTS LIST IGREMLIN INDUSTRIES INC] B40! AERO OR SAN DIEGO, CA. 92123

ee SCHEMATIC Boe Set 2 BLASTO Aare aa VIDEO LOGIC BOARD LON CONMEC TOR PINS 5,!5. .139.64,98,52,54,57 ARE, 119-000: ‘ DRAWING BO. BEATA KEYING Pins 7 TF-DT01 NEXT Assy USED ON NOTES: "APPLICATION DO_WOT SCALE DRAWING

Page 58

REVISIONS DESCRIPTION Peccace Ros =cw Ror

IMEG 10K

N.C. Psy PRr7 RRs RRs AR RRrg PReo

NOMENCLATURE OR DESCRIPTION PARTS List IGREMLIN INDUSTRIES INC] B40! AERG DR. “AN DIEG2. =A 92123

SCHEMATIC BLASTC VIDEO LOGIC BOARD

Page 59

REVISIONS DESCRIPTION A|TRELEASED oe | SWITCH SLIDE 510-0014

oe, CONN. BLOCK FEM. {fin1 OPIN 2/2-00/6 CONN. QUICK 1/4"FEM 2u- 0017 (6£A) .O-—— _——CONN. CRIMP LocK SI 31/0005 (GEA)

CONN KEY PLZ. “a fee 211-0007 (IEA) CABLE T/E 280-0005 APPOX. 6” APART (/2E£A) f—~4.0 —-74.0 TO VIDEO LOGIC BO. \- CONN. RING LUG CONN. SPADE LUG 2N-OO19 (1EA) 21-0027 (EA)

Soke R —Y BRACKET SWITCH 250-003) (EA) CONTROL BLOCK DECAL——_ 420-0046

. CONT. — KNOB VOL. Con =|PIN! CONN. BLOCK FEM. "4 PIN 212-0005 240-0001 CABLE, SHIELDED NN TWO CONDUCTOR “CONN CRIMP LOCK 600-0029 \ 2il-cO0S (3EA) <POT. 1OK VOL CONT. \ 475-0007 \-CONN. KEY PLZ, 211-0007 (WEA) CONN. BLOCK FEM— 4PIN 212-0005

CONN.CRIMP Lock“ TOVIDEO 3 )1-0005 (2EA} LOG/C BD. ro puAL CONN. KEY PLZ. -O007 COIN MECH, eu 0007 (ZEA)

QTy CODE PART OR NOMENCLATURE REQD} IDENT IDENTIFYING NO. OR DESCRIPTION: PARTS LIST GNLESS OTHERWISE SPECT 6RN BIMENSIONS. mein INCHES. Gremlin Industries, Inc. GRO. WIRE FRACTIONS DECIMALS ANGLES San Diego, California 92122 = x50 = ; —

CONT REL BLOCK BLAS/C CODE IDENT NO. [ORAWING NO. Co

7/9 -0002 | BLASTO 719-9001 | BLASTO NEXT ASSY USED ON APPLICATION DO_NOT SCALE DRAWING SCALE OAS

Page 60

TITLE

Gremlin Induséries, Ine, al VIDEO LOGIC BOARD) 817-0026 a A mewn Contormie BLASTO DWG NO OF 8 | REV

= APPR {1.2 54 ot /LTR| DATE REVISION DESCRIPTION DRAFT | CHECK | APPR Pa [5-57|_@EORAWN —=T edo [eee | FORM NO. 001-1500

Page 61

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 62

TITLE

Gremlin Industries, Inc. Pier | V/iDEO LOGIC BOARD

BLASTO

| QTY PER ASSY |

S.1K OHM VY2W 5 %e| R#8,R51, R5G,R73 6.8K OHM YaW 5%70| ROI,RU 8.2K OHM Y2W_5% DIODE (N#002 XSTR 2N 3565 |XSTR 2N44O3R

Page 63

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 64

Gremlin Industries, Inc.

PART NO

PARTS Li

LIST

QTY PER ASSY

TLE

(DEO LOGIC BOARD

BLASTO

DESCRIPTION

3/b-O0OVG | 1 |

JI924X4 PROM

B19-O0026 |SH4t OF 6

REF DES

31@-O09T| 7 | 3ib- OOFB

é (le 1024 X4 PROM /O24X4+ PROM ‘2B /. iD Js 310-0099 [I . Cc. 5Ii2X + PROM 316-0100 [I C. 5IZX 4 PROM U43 fl LED. RED D7 48| 47/-O101 |/ RES /00 OHM “2W 5%| R53 49 RES 1K OHM VW 5% | RI-RC7,R3R39-R41,R44,R50,

R55, P64, RE5,RLI,R16,R TP, REQ tn S

RES 1OK OHM

Y2W 57 &

RES 15 OHM Y2W 5% 471 - DI54¢

RES 150K OHM /2W 5%

RTZ 471-0220

RES 22 OHM AW 5%

RF3,R45 RES 220 OHM YAW S%

RF 28,R4Z,R54,RB4,R86 > rs

PES 2.2K OHM VY2W 5%

R38 by S

RES 22K OHM AW 5%

R29-R36,RLO 8) N

RES 220K OAM YaWS%

R68 58 RES 2.7K OHM Y2W 5%| RTB 411-0331 [4 RES 330 OHM 2W S%| R46,R 47, RAI,RSZ

| | RES S2K OHM AW 5% 59, R63,REL,R1O 47/- 033F|1 = RES 330K OHM Y2W S% 471-O4 71 |_| 410 OHM (72W 5%

Page 65

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 66

TRB

‘|

omit 5 last Cast 3, Last @ LAST

  • Last Notes: QQ? .DI,D3,D4, 036, USL, CH, CSI EL EZ ¢ No. USED C52 d USED D& R No, USED RBG @Q No. USED Qi U No. USED Ves

UNLESS OTHERWISE SPECIFIED \o.

q JUMPER WIRES AS NoreD

CAPACITANCE YALUES ARE IN MiCROFA@ADS

  • RESISTANCE YALUES ABE IN OHMS Y CONNECTOR PINS 4,/5,27, 74,44 ,48,52,54,57 ABE BLANK KEYING PINS

i 6 REVISIONS. DESCRIFTON

_—® 7 PLACES

2 PLACES

SEE DETACHED PARTS LIST

NOMENCLATURE OR DESCRIPTION

Foncess orremwise SpEGIIED DIMENSIONS ARE IN TOLERANCE: PARTS LST Gremlin Industries, Ine. San Bioge, caiifornia 92723 S/9-2026 \A

B.C. ASSEMBLY -——— VIDEO LOGIC BOARD BLASTO

Do_NOT SCALE DRAWING [CODE TOENT NO] DRAWING NO. 8B19- O02

Page 67

Ris 1K

AS ii oO ODO © em © > 13,2490 rey s b 5 icy) off VEV EVE VE VEY:

U2 Us 1024x4 PROM 1024x4 PROM 316-0098.

OUT 7 SHT.2 T our 6 sur. 2¢

  • OUTS SHT. 2 ouT 4 Ser?

ouT 3 SHT. 2

our 2 sH7.2 READY ah ols SHT.2 aN TP3 A START O Res 1? Tes

,1kiy se

al MEMW

pe38SHT. 2

220.0 2K me Le os ‘SHT. +

iabe R18PadeSan

220.2 1P7 as Reg "7406 .

aReeSe SE | eclith.PaI

$ PARTS LST

onspaeca yen meres | PTTIGREMLIN INDUSTRIES INC
,anarLice iaal ET=app bao! AERO DR.SAN DIEGO, GA. 92123

lout by ae Cond

Coated] C25mamepam Joe M._—j014-T6SCHEMATIC
eae] O5ufane2/re]BLASTO

af 3 +5 Fos Sono Ded = VIDEO LOGIC_BOARD LON CONNECTOR PINS 3,15, 27,15,44,48,52,54,57ARE | OED OD Hin SE [0008 (Dent no. |DRANG We ed

BLANK KEYING PINS.19-0003) BLASTOD8 "q -0026 A

: Terr ASSY USED On

NOTES:APPLICATIONDO NOT SGALE_DRAWNGSeAe NONEper] FB
—7654321

819-0026] A

Page 68

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 69

B9-0027 ~—= *(|SH!

DWG NO OF 3

SHEET 32 19 D SIZE

| LTR] DATE REVISION DESCRIPTION Ti |s/«| Peeto LA Way FORM NO. 001-1500

Page 70

{

avis Ol, ‘wahowM “XAH 2¢-0O1 DLN H2LIMS ODIM' aardvdAS LHANAdN TWOALNOD ' TaN

  • yaa YVAnMd NaLLhNAa MONNAA AWENAA NOLLNE PALS AOL ASS HDLIMS 1400 - bis Nolladlaosaa ON luvad a ASSW Yad ALO au

ON SMG STLIL ol—[P]s [a

Page 71

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 72

—rrP (6) PLES

  • TO INSTALL SI9- 003) switch AGS. TO OPERATOR PANEL , REMOVE CONTROL KNOB. WHEN RE-INSTALLING KNOB, SECURE TO THREADEO ROP WITH LOCTITE OR RQUIVALENT SE:ZING COMPOUND,

DRAWING RO,

NOTE eT BI9- 027
Page 73

THEE CWwitcn Aooy, |8'197- COB! |sH |], JOY STick DWG NO OF 7 | REV DRAWN. SMITH

PARTS

LIST

Sat Ss Le [LTR] DATE |

APPR

DRAFT

REVISION DESCRIPTION

fh/rs| RELEASED | FORM NO. 001-1500

CHECK

| CHECK | APPR | x14)

Page 74

PART NO

B17 -CO3l

DWG NO

ZS0- 029%

ADAPTER, SWITCH MOUNTING

SPACER, SW ITCH

PLATE , SWITCH

SPACER ,TUBULAR ("

SVACER ,TUBLAR a"

SPACER, TUBULAR (275) Rov, THREADED

Page 75

REVISIONS

‘DESCRIPTION

RELEASED

Decontron KNOG TO BE TEMPORARILY INSTALLED THIS AGSY.

SWITCH ASSY. TOY STICK TE] CODE IDENT NO [DRAWING NO. A

NOTE’ oa = — | 8 19-0031 ss.