CATHODE RAY TOMES

Cheyenne

Cheyenne (version 1.0) (Exidy, 1984) · Manual · 45 pages · 14 sections · original scan

Page 1

Operator's and Service

  • MANUAL

First Edition

Page 2

FOREWORD

PART ONE: Contains Preliminary Procedures, describing game inspection, installation, and checkout.

PART TWO: Adjustment procedures are given for Power Supply, Audio Volume, Selectable Options, Gun Sight Alignment and Optical Sensitivity Adjustment.

PART THREE: Modes of Operation, describes the four CHEYENNE™ modes: Automatic Self-Diagnostic Test Mode, Manual Diagnostic Mode, Attract Mode.

PART FOUR: Contains the Electrical Schematics.

PART FIVE: Contains the Mechanical and the Electronic Part Breakdown.

Page 3

TABLE OF CONTENTS

  • PRELIMINARY PROCEDURE
  • GAME INSPECTION ....
  • VISUAL INSPECTION FILING A CLAIM . INSTALLATION . MAJOR COMPONENTS . GUN STOCK INSTALLATION . PRELIMINARY CHECKOUT PROCEDURE
  • apyusrmMeNTS ORO EEE MO GOR we

1, POWER SUPPLY INFORMATION AND ADJUSTMENTS 9

  • AUDIO BOARD ADJUSTMENT 9
  • OPERATOR SELECTABLE OPTIONS ... 10 a, Coinage eee eee eeeeeeeeeeeeeees 10 b. Starting Number of Characters. . 10 c. Game Play Difficulty ...... 10
  • OPTICAL SENSITIVITY ADJUSTMENT ul
  • GUN SIGHT ALIGNMENT - 12
  • MODES OF OPERATION 1, AUTOMATIC SELF-DIAGNOSTIC TEST MODE ..
  • MANUAL DIAGNOSTIC MODE .
  • THE ATTRACT MODE
  • SCHEMATICS . WIRING DIAGRAM .. LOGIC PCB . AUDIO PCB .. . OPTICAL PCB . . POWER SUPPLIE!
  • PARTS LIST MECHANICAL 0... eee ce cece ener e ence en ene 35-37 2 LOGIC PCB .. sees : cee!
  • AUDIO PCB 4, POWER SUPPLY . 5. 6. heme

. OPTICAL PCB .

Page 4

LIST OF ILLUSTRATIONS

. Major Component Locations a. PCB Assembly Locations b. Rear Access Panel

. Cheyenne™ Stock . Gun Sight Alignment . Power Supply and Volume Adjustment

« Gun Stock

  • Optical Adjustment

. Gun Sight Alignment . EPROM and RAM Error Code Locations

. Wiring Diagram . Gun Assembly

. Audio PCB

. Power Supply

. Optical PCB

Page 5

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 6

PRELIMINARY PROCEDURE

GAME INSPECTION

All Exidy equipment is carefully packaged in well-padded cardboard containers to prevent damage during shipment. Before signing the delivery receipt, you should follow this procedure:

  • Check for obvious damage and make certain that the physical piece count of the shipment matches the piece count on the bill of lading. These wo procedures should always be done before signing the delivery receipt.
  • Shortages and/or obvious damage to the packaging on any given shipment should be noted in writing on the delivery receipt before signing for the delivery.
  • If concealed damage is suspected on any shipment, those packages believed to contain the damaged goods should be opened in the presence of the delivery driver. If the goods have sustained concealed damage, a description of said damage should be noted in writing on the delivery receipt before signing for the delivery.
  • Never apply power to any game with noticeable damage.

VISUAL INSPECTION

  • Remove the rear and front access doors with the appropriate packaged key.
  • Examine each major and electrical component thoroughly for scrapes, dents, broken or missing parts and loosening screws.
  • Check for loose cable connectors.
  • Visually verify that all the integrated circuit devices (IC’s) plugged into sockets are properly seated and that no IC pins are bent or misaligned. If you find any damage during this inspection, file a claim with the carrier. Send a complete report of the damage to Exidy Inc.

FILING A CLAIM

TO FILE A CLAIM, FOLLOW THIS PROCEDURE:

  • Any and all damaged freight, including packag- Tf warranted, a written claim must be filed with ing, should be retained by the consignee until a physical inspection of said freight can be made by a representative of the carrier involved.
  • The Claims Manager for the carrier involved should be notified as soon as possible after the damaged goods are received. Preferably, the cartier’s Claims Manager should be notified within forty-eight (48) hours of receipt of the goods by the consignee. the carrier(s) involved. A detailed description of the damage(s) must be provided including copies of delivery receipt and/or bill of lading, inspection report and invoice. The carrier(s) to which a claim has been filed against is required by law to respond to within thirty (30) days after receiving your claim and must reach a final disposition in the matter within one hundred twenty (120) days.

QUESTIONS

Exidy encourages technicians to use the toll-free customer service holline for any questions they may have regarding CHEYENNE™: That number is (800) 538-8402.

es Cl |

Page 7

INSTALLATION

Planning the location of the game should involve both physical and electrical considerations. Such physical considerations concern the placement of the equipment with respect to these clearances:

@ HEIGHT: 80.00 inches, 203.2 cm. @ WEIGHT: 25.25 inches, 65.1 cm. © DEPTH: 35.00 inches, 88.9 cm.

An indoor, relatively dust-free environment is necessary, with proper conditions required of any electrical component. Electrical considerations include availability of an AC outlet with the correct voltage and frequency. You should consider the working space required for technicians and operators including access to the rear of the game.

NOTE: CAUTION:

The cabinet must be within five feet of an AC outlet. Be certain DO NOT remove the AC ground prong from the plug. Doing so that a ground jack or terminal is available at the outlet. VOIDS YOUR WARRANTY! cadets

Page 8

MAJOR COMPONENTS

The Cheyenne™ game is a colorfully illustrated upright video game with high resolution graphics.

The major components of your Cheyenne game arc illustrated in (See Fig. 1). These major components are the following: © Cheyenne Gun © Coin Mechanism © Monitor Chassis © Power Supply Chassis © Control Panel © All PCB Assemblies @ Speakers

The PCB assemblies are listed as follows:

© Game Logic PCB Power Supply PCB © Audio PCB © Photo Optic PCB

—_—— GUN

MONITOR ——

START BUTTON

K SWITCH ENTERLOCK.; {= INTERLOCI

LOGIC BOARD ———— |______. COIN DOOR

POWER SUPPLY

ELI SERVICE| DOOR

Fig. 1 MAJOR COMPONENTS

Page 9

GUN STOCK INSTALLATION

MECHANICAL Gun Stock is detached from the forestock for shipping. To install Cheyenne™ gun stock, proceed as follows:

  • Locate the 3 mounting screws, packed inside shipping carton with Cheyenne Gun. . Loosen the 8/32 set screw in the FORESTOCK that secures down the OPTICAL TUBE ASSEMBLY.

. Check that the gun optic PCB connector is in place. x wo

Gently place gun stock onto forestock mount with the (2) 10-241 button head screws, and (1) 1/4-20x2 3/8 cap screws and secure gun stock to forestock (See Fig. 2).

NOTE: Be sure to tighten down the set screw in FORESTOCK that secures the OPTICAL TUBE ASSEMBLY.

CAP SCREW (/4-20%2-3/8)

Page 10

PRELIMINARY CHECK PROCEDURE

AFTER PROPERLY INSTALLING THE STOCK PROCEED AS FOLLOWS:

  • Connect the power plug into 110 VAC 60 Hz outlet.
  • Three seconds after power-up there should be a burst of sound followed by the AUTO SELF DIAGNOSTIC TEST.
  • Following the AUTO SEL the game will enter the A’ IAGNOSTIC TEST RACT MODE.
  • When AUTO SELF TESTS are completed and the gun stock is properly installed proceed with the GUN SIGHT ALIGNMENT.

GUN SIGHT ALIGNMENT

  • Open the Goin Door to access the AC interlock switch, game will power down.
  • While holding down the START BUTTON pull

GUN SIGHT —~ out the interlock switch to restore power. After a burst of sound the screen should display the MANUAL DIAGNOSTIC MENU MODE.

. Be sure the index is pointing to GUN SIGHT ALIGNMENT, use the Start Button to index if not.

. Pull gun trigger and a crosshair (+) will be displayed, release gun trigger.

. Aim the gun sight to center of crosshair, pull gun trigger once and gun sight will be aligned to the last burst.

. Press down the START BUTTON and return to the MANUAL DIAGNOSTIC MENU. With the START BUTTON move the index to EXIT MODE, press the GUN TRIGGER and return to the ATTRACT MODE.

fo GUN BURST

FIG. 3 GUN SIGHT ALIGNMENT.

Page 11

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 12

ADJUSTMENTS

I. POWER SUPPLY INFORMATION AND ADJUSTMENTS

ALL DG Power required to operate Cheyenne™ is supplied by the Exidy Power Supply Module. These supply outputs are as follows: e+5V ... ...@ 9 AMPS © +18V @ 3 AMPS © -18V ...@ 8 AMPS

CAUTION: Only certified technicians should make adjustments on all components of Cheyenne™ Only the +5v DC is adjustable. This must be adjusted to: +5.00 VDC as measured on the PCB near the microprocessor (location J2) (See Fig. 4).

COIN oN

AND CREDIT CHARACTERS \ OPTIONS SWITCH / OPTIONS SWITCH

SWITCH-1

a

Fig. 4 ADJUSTMENT LOCATIONS

II. AUDIO BOARD ADJUSTMENTS Adjust R15 master audio volume control located at position T2 on the Audio Logic Board (See Fig. 4) and adjust audio level while game is in progress. This audio board rides piggyback on the logic board, mounted inside of the cabinet on the side wall (See Fig. 1).

Page 13

III. OPERATOR SELECTABLE OPTIONS

Cheyenne™ has several selectable switch options controlled by an 8 position DIP SWITCH located at B1 of the AUDIO BOARD and a 4 position DIP SWITCH located at J19 of the LOGIC BOARD. Both switches are accessible through the rear door of the game.

SWITCH OPTION SETTINGS 8 POSITION SWITCH LOCATION B1

@ = FACTORY SETTINGS

COINAGEasirenoeali
FREE PLAY —ONOFFOFFOFFOFF
1 COIN— 1 CREDITOFFOFFOFFOFFOFF
@2COINS—1CREDITOFFOFFONOFFOFF
3COINS—1CREDITOFFONOFFOFFOFF
4COINS—1CREDITOFFONONOFFOFF
1 COIN— 2 CREDITSOFFOFFOFFOFFON
2COINS—2CREDITSOFFOFFONOFFON
3COINS— 2 CREDITSOFFONOFFOFFON
4COINS— 2CREDITSOFFONONOFFON
1 COIN— 3 CREDITSOFFOFFOFFONOFF
2COINS—3 CREDITSOFFOFFONONOFF
3COINS— 3 CREDITSOFFONOFFONOFF
4COINS—3CREDITSOFFONONONOFF
1 COIN— 4CREDITSOFFOFFOFFONON
2COINS—4CREDITSOFFOFFONONON
3COINS—4CREDITSOFFONOFFONON
4COINS—4CREDITSOFFONONONON

SWITCH OPTION SETTINGS 4 POSITION SWITCH LOCATION J19

GAME PLAY DIFFICULTY SWITCH SWITCH SWITCH swiren

123

+

1 EASYONON
@2 NORMALOFFOFF
3 HARDOFFON
5 MOST DIFFICULTONOFF

STARTING CHARACTERS

2 CHARACTERSOFFON
@ 3 CHARACTERSOFFOFF
4 CHARACTERSONOFF
5 CHARACTERSONON

-G

Page 14

IV. OPTICAL SENSITIVITY ADJUSTMENT The Cheyenne uses an Optical Sensor PCB mounted in the forestock to monitor the scanning electron beam of the CRT. Gun positioning information from this Optical Sensor PCB is monitored by the Logic PCB. The Optic PCB sensitivity adjustment allows for monitor intensity, distance between gun and monitor and the electronic circuitry tolerance. During game play each time the trigger is pulled there will be a white flash and a small dot is displayed wherever the gun is aimed. If for any reason the optic circuitry is not sensing the screen when the trigger is pulled the dot will not be displayed, and an audio

warning sound will be heard. When this occurs, the optical sensor sensitivity should be readjusted.
  • To access the optical electronics, remove the (2) button head screws and the (1) cap screw and gently lift the Gun Stock from the Forestock (See Fig. 5).
  • Select the MANUAL DIAGNOSTIC MODE. To enter this mode, hold down the Start Button while applying power,

SET SCREW FORESTO

PCB

  • Index the pointer to the CHECK INTERRUPTS test, pull gun trigger and execute. When test is complete it will return to the MANUAL DIAG- NOSTIC MENU MODE.
  • Index the pointer to the OPTICAL ADJUST- MENT and pull Gun Trigger, a white screen should appear.

. If the screen should come up with wavering lines, repower the game and return to MANUAL DIAGNOSTIC MENU. Perform the CHECK INTERRUPTS, then index to the OPTICAL AD- JUSTMENT.

(continued)

Fig. 5 GUN STOCK

Page 15

6.

v.

3. Aim the Gun to the enter of the screen, an orange rectangular pattern with a brown leading edge should be displayed (See Fig. 6-C). . Turn sensitivity control CCW until oscillation and an orange rectangular pattern are displayed (See Fig. 6-A). Now turn sensitivity control CW until oscillation diminishes just beyond this oscillation point (See Fig. 6-B), from this point turn sensitivity control CW approx. 4 turn more. This should be the optimum setting.

S S SS S a

BAD

  • The rectangular pattern should appear on the screen wherever you aim the Forestock (Optic), with the exception of approx. 2” to the extreme left of screen.
  • Reinstall the Gun Stock Assembly. Refer to Cheyenne™ Stock Installation procedure (Page 4 Steps 2 & 3). This completes the optical check.

Fig. 6 OPTICAL ALIGNMENT.

GUN SIGHT ALIGNMENT

. Open the Coin Door to access the AC interlock switch, game will power down (See Fig. 1)

While holding down the START BUTTON pull out the interlock switch to restore power. After a burst of sound the screen should display the MANUAL DIAGNOSTIC MENU MODE. Be sure the index is pointing to GUN SIGHT ALIGNMENT, use the Start Button to index if not.

> Pull Gun Trigger and a crosshair (+) will be displayed, release gun trigger.

  • Aim the Gun Sight to center of crosshair, pull Gun Trigger once and Gun Sight will be aligned to the last burst (See Fig. 7).

p———————_——— PULSING BURST

Fig. 7 GUN SIGHT ALIGNMENT

Page 16

Modes Mae Opin | Mae Opin |

Page 17

MODES OF OPERATION

CHEYENNE™ HAS FOUR MODES OF OPERATION:

A. AUTO SELF DIAGNOSTIC TEST MODE B. MANUAL DIAGNOSTIC MODE C. ATTRACT MODE D. PLAY MODE

To bypass all diagnostics, press rifle trigger during the power-up sequence.

AUTO SELF DIAGNOSTIC TEST MODE

RAM TEST SCREEN RAM TEST CRC OF PROGRAM ROMS CHECKSUM OF DATA BANK ROMS AUDIO TEST E? PROM

MANUAL DIAGNOSTIC MENU MODE

To access the manual diagnostic mode, hold down the START BUTTON on power-up. Once this mode is accessed, any of the listed selections may be indexed by the player start button and executed by the GUN TRIGGER.

GUN ALIGNMENT

Displays a crosshair (+) for gun sight alignment. Aim the GUN SIGHT at center of crosshair and fire gun once. the GUN SIGHT will be aligned to the last burst.

NOTES: Press START BUTTON and return to the MANUAL DIAGNOSTIC MENU.

RAM TEST

Tests RAMS on logic board at locations A8 and Ag

SCREEN RAM TEST

Tests RAMS on logic board at locations:**

B14-B21 C14-C21 D14-D21 E14-E21

CRC CHECK OF PROGRAM ROMS

Tests ROMS on logic board at locations Al, A3, A4, and A6**

CHECKSUM OF DATA BANK ROMS

Tests ROMS on logic board at locations:* B1, B3, B4 B6,B7,B8,B10 C8, C10, Cll D1, D3, D4, D6,D7,D8, D10, El, E3, E4, E6,E7, E8, E10, Ell

AUDIO TEST

Tests the communication between logic and audio board.

  • See Diagnostic Error Gode FIG. 8 for suspected location of RAM or ROM. ** The Processor may not run dependent on the extent of chip failure of these locations. ee —————————
Page 18

CHECK INTERRUPTS Tests for horizontal and vertical frame interrupts.

GRAY SCALE

Displays a graduated gray scale for monitor check or adjustments.

CROSSHATCH

Displays horizontal and vertical lines for monitor linearity and convergence checks or adjustments.

COLOR BARS AND BLOCKS

Displays a color visual test pattern utilizing the backround and moving object circuitry. ‘The bars are produced by the backround circuitry and the blocks are produced by the moving object circuitry.

OPTICAL ADJUSTMENTS

Displays a rectangular pattern for adjusting the sensitivity of the Optical Sensing Circuitry.

RESET TO FACTORY SETTINGS

Sets the high score and also checks the E? ROM*** located at B11 of the logic board. The E* PROM contains the high score table and gun alignment information. Running this diagnostic will reset the high score table. It will also require that the accuracy of the gun alignment be rechecked.

RESET HIGH SCORE TABLE TO ZERO

Resets all high scores on the high score table to zero. (Same as reset to factory set )except to zero.

EXIT

Returns game to the ATTRACT MODE.

FREE PLAY

For those wishing to demonstrate Cheyenne, a freeplay mode may be achieved by turning on switch #1 on audio board at location Bl.

ATTRACT MODE

The attract mode appears after power-up auto self diagnostic and after every game. This mode will continue to display the attract mode repeatedly until a coin, and the start button is pressed.

HIGH SCORE TABLE

GAME SCENE

COIN AND CREDIT INSTRUCTIONS

GAME PLAY INSTRUCTIONS

NOTE: ** E? PROM = Electrically Erasable Programable READ ONLY MEMORY.
Page 19

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 20

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 21

‘Avo0 ano,

Fig. 10 WIRING DIAGRAM

Page 22

eee

Page 23

ee) erik amet Y90 sretene

Page 24

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 25

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 26

id

nae Arms meen eam) Sr onr os ney

Page 27

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 28

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 29

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 30

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 31

mae |

  • re DELTA moo (A a o fone” Pet El Pia eT v “ Feol
Page 32

0g

a 20K. paws aI aNyt04 Lt 8 re WK

Kw sae agh § cA,

Page 33

PRODUCTION NOTES: | JUWER WITHLLD To ONE Sonne Las, 20,00

= AC CONNECTION TABLE A, FOR USE AT. USAC | 225UAC

aTEENIEas‘
aPRLY AEA[assTetee EG,Ja"bon

FUSE INPUT AT SA 75K t ‘se 1 Lied

wan ers

Tor ae 01 Faces) * — nt dan TL &; Ba | Cid provi © a

ta pho fu fa oa, ' ul 2 aTZ> enn @ 0 P user

® ™ ame, b

© q@ cay eas jeas fom |, + Ay ry

:GonSara

a A Me, OE Sag

mH ws++—

+ 5 VOLT REGULATOR SUPPLY

Page 34

bs ee)

sMTeH x)

PROGRAM PLUG

RED RED

MO PLUS yet

HSC POWER SUPPLY WIRING DIAGRAM ruren-

PIT aw

Page 35

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 36

MECHANICAL PARTS

APPENDIX B: The following is a list of parts with part numbers should you ever need to order replacement parts for your Cheyenne™. Replacement parts orders should be placed through your local “Exidy” Distributor.

PART NUMBER DESCRIPTION

01-0111-00 ASSEMBLY, LOGIC & AUDIO PCB SET

98-0006-00 ASSEMBLY, CABINET 74-0001-00 ASSEMBLY, REAR DOOR 65-0131-00 BRACKET, INTERLOCK REAR DOOR 65-0132-00 BRACKET, INTERLOCK COIN DOOR 48-5012-00 SWITCH INTERLOCK 48-3006-00 SWITCH, START BUTTON

95-0018-00 ASSEMBLY, FLUORESCENT FIXTURE 95-0019-00 BULB, FLUORESCENT 15W 95-0030-00 STARTER, FLUORESCENT

95-0017-00 SPEAKER 6 x 9 65-0114-00 GRILL, SPEAKER

79-0001-00 ASSEMBLY, 19" COLOR MONITOR 90-0101-00 ASSEMBLY, BEZEL

90-0096-00 ASSEMBLY, COIN DOOR 95-0036-00 COIN BOX ENCLOSURE 95-0035-00 COIN DOOR 95-0016-00 CASH BOX PLASTIC 95-0015-00 COIN COUNTER

90-0098-00 ASSEMBLY INTERNAL ARTWORK 80-0075-00 INTERNAL ARTWORK RIGHT & LEFT 80-0077-00 INTERNAL ARTWORK TOP 80-0078-00 INTERNAL ARTWORK BOTTOM

80-0106-00 OVERLAY, CONTROL PANEL 80-0110-00 DECAL, LEFT SIDE 80-0109-00 DECAL, RIGHT SIDE

80-0108-00 PLEX, MONITOR 65-0113-00 BRACKET, MONITOR

80-0107-00 PLEX, LOGO 65-0110-00 BRACKET, LOWER 65-0111-00 BRACKET, UPPER

80-0068-00 MIRROR 65-0113-00 BRACKET, MIRROR 51-2204-00 SCREW, #8 x 1/2 P.H.X.

(continued)

| es

Page 37

HARNESS

PART NUMBER DESCRIPTION

49-0067-05 ASSEMBLY, GUN 49-0066-05 ASSEMBLY, FLUORESCENT LAMP 49-0065-05 ASSEMBLY, 50 PIN RIBBON CABLE 49-0064-05 ASSEMBLY, COIN DOOR 49-0063-05 ASSEMBLY, CONTROL & COIN INTERFACE 49-0062-05 ASSEMBLY SPEAKER 49-0061-05 ASSEMBLY, INTERLOCK DIST. 49-0060-05 ASSEMBLY, LAMP & MONITOR 49-0059-05 ASSEMBLY, VIDEO 49-0058-05 ASSEMBLY, D.C. SUPPLY

GUN ASSEMBLY

PART NUMBER DESCRIPTION

90-0091-00 ASSEMBLY, GUN MOUNT 75-0011-00 KNUCKLE MOUNT 75-0012-00 RING MOUNT 70-0048-00 PIVOT PIN 50-1108-27 SCREW, 6/32 x 3/8 90-0092-00 va ASSEMBLY, FORE STOCK 95-0033-00 ROLL PINS 3/16 x 1-1/4 95-0034-00 SPRING, TRIGGER 75-0013-00 * FORESTOCK, CASTING 70-0047-00 BUSHING, TRIGGER 70-0049-00 TUBE MOUNT 65-0125-60 TRIGGER PLATE 55-0004-00 a NYLON SPACER 1/2 x 8 CLEARANCE 50-9905-00 SCREW, 256 x 5/8 P.H.X 50-2103-27 SCREW, 8/32 x 3/8 50-2104-00 SCREW, 8/32 x 1/2 50-2106-00 SCREW, 8/32 x 3/4 48-3005-00 SWITCH, MICRO #483005-001 37-0018-00 CLAMP, NYLON RICHO N-2

90-0093-00, ASSEMBLY, OPTIC TUBE 77-0020-05 ASSEMBLY PHOTO DETECTOR PCB 80-0076-00 PHOTO SENSOR HOLDER 80-0069-00 PLANO-CONVEX LENS 25MM x 100MM F.L.

90-0113-00 ASSEMBLY, GUN STOCK

  • CASTING, GUN BARREL CASTING, GUN STOCK ALLEN SCREW, 10-32 x .625 ALLEN BOLT, 1/4-20 x 2 1/4
Page 38

GUN ASSEMBLY

BUTTON HEAD SCREW (10 "24x 1)

OPTIC TUBE

SIGHT ALIGNMENT

SET SCREW CAP SCREW 8-32x3/8 (1/4-202 3/8)

FORE STOCK SWIVEL MOUNT

MOUNTING KNUCKLE

PIVOT PIN

Fig. 11 GUN ASSEMBLY

Page 39

Fig. 12 LOGIC PCB

Page 40

LOGIC PCB

PART NUMBER DESCRIPTION

77-0019-04 77-0019-05 74-8547-00 49-0065-05 48-5016-00 44-1601-00 44-2401-00 44-2801-00 44-4001-00 41-0009-00 40-0021-06 40-0021-10 40-0061-00 29-0005-00 28-0005-00 28-0006-00 27-0003-00 25-0007-00 23-0045-00 22-0001-02 22-0002-02 22-0003-02 22-0005-02 22-0007-02 22-0010-02 22-0011-02 22-0012-02 22-0013-02 22-0014-02 22-0015-02 22-0016-01 22-0016-02 22-0017-02 22-0020-02 22-0021-01 22-0021-02 22-0022-02 22-0027-01 22-0027-02 22-0030-02 22-0041-02 22-0043-02 22-0044-02 22-0061-02 22-0062-02 22-0063-02 LOGIC PCB BLANK LOGIC PCB SPACER, SNAP-IN CABLE, RIBBON 50 CONDUCTOR SWITCH, 4 POSITION DIP SOCKET, 16 PIN SOCKET, 24 PIN SOCKET, 28 PIN SOCKET, 40 PIN CONNECTOR, 50 PIN RIBBON CONNECTOR, 6 POSITION INLINE CONNECTOR, 10 POSITION INLINE CONNECTOR, 10 POSITION MALE CRYSTAL, 12.979 MHZ 1.C., 2804 RAM (300NS) 1.C., 2149 RAM (35NS) L.C., NE555 1.C., 68B09E CPU 2MHZ 1.C., 6116 1.G,, 74LS00 LC, 74LS02 LC, 74LS04 LC., 74LS08 1.C., 74LS20 L.C., 741832 LC., 74L874 LC,, 74LS112 LC., 74LS138 .C., 74LS139 , T4LS157 .C., 748161 LC, 74LS161 LC., 74LS166 LC., 7418245 L.C., 748374 .C., 74LS374 .C., T4LS154 1.C., 74886 LC., 74LS86 1.C., 74LS151 1.C., 74LS10 1.C., 74LS169 1.C., 74LS283 1.C., 7418244 1.C., 74LS05 LG., 741830

(continued)

Ci

Page 41

PART NUMBER LOGIC PCB

DESCRIPTION

22-0064-02 22-0065-02 22-0066-02 22-0067-02 22-0068-02 21-0006-00 21-0007-00 21-0008-00 20-0008-00 13-1062-00 13-1075-00 13-6844-00- 11-3305-02 10-1034-1 10-1044-1 02-1012-00 02-1021-00 02-1022-00 02-1032-00 02-1052-00 02-1631-00 02-2021-00 02-2222-00 02-2712-00 02-3312-00 02-3322-00 02-4021-00 02-4712-00 02-4722-00 02-8021-00 L.C., 74L825 L.C., 7418153 LC., T4LS173 LC., 7415189 LC, 7418273 REGULATOR, 7812 ‘TRANSISTOR, 2N3904 TRANSISTOR, 2N3906 DIODE, 1N914 CAPACITOR, 10UF CAPACITOR, 100UF CAPACITOR, 6.84F DIP-TANT CAPACITOR, 3.34F CAPACITOR, .014F CAPACITOR, .1 uF RESISTOR, 100 OHM RESISTOR, 1K 1% RESISTOR, 1K RESISTOR, 10K RESISTOR, IMEG RESISTOR, 16K RESISTOR, 2K 1% RESISTOR, 2.2K RESISTOR, 270 OHM RESISTOR, 330 OHM RESISTOR, 3.3K RESISTOR, 4K 1% RESISTOR, 470 OHM RESISTOR, 4.7K RESISTOR, 8K 1%

Page 42

AUDIO PCB

PART NUMBER DESCRIPTION _|

77-0022-04 AUDIO PCB BLANK 77-0022-05 AUDIO PCB 49-5002-00 SWITCH, 8 POSITION DIP 44-1601-00 SOCKET, 16 PIN 44-2401-00 SOCKET, 24 PIN 44-2801-00 SOCKET, 28 PIN 44-4001-00 SOCKET, 40 PIN 41-0003-00 CONNECTOR, 10 PIN FEMALE

40-0005-10CONNIR, 10 PIN MOLEX
40-0021-08CONN‘OR, 8 POS. INLINE
40-0021-10CONNIR, 10 POS. INLINE

40-0021-12 CONNECTOR, 12 POS. INLINE 27-0004-00 L.C., MC3417L 27-0006-00 L.C., AD558 27-0007-00 LC., MC3418 26-0005-00 ‘ 25-0008-00 .C., 6809 CPU 23-0045-00 LC., 6116 22-0001-02 IC., 74LS00 22-0003-02 IC., 74LS04 22-0004-00 1C., 7407 22-0005-02 IC., 74LS08 22-0010-02 IC., 74LS32 22-0011-02 IC., 74LS74 22-0014-02 IC., 74LS139 22-0015-02 IC, 74LS157 22-0016-02 IC., 74LS161 22-0017-02 IC., 74LS166 22-0020-02 IC., 7418245 22-0021-02 IC., 74LS374 22-0026-00 IC., LM324 22-0027-02 IC., 74LS86 22-0028-00 IC., 4051 22-0036-00 1C., LM741 22-0038-02 IC., 74LS367 22-0039-02 IC., 74LS42 22-0061-02 IC., 74LS244 22-0067-02 IC., 74LS189A. 22-0071-00 IC., 7406 22-0077-00 1C., CA3080 21-0001-00 TRANSISTOR, TIP 120 21-0002-00 TRANSISTOR, TIP 125 21-0005-00 REGULATOR, 7912 21-0006-00 REGULATOR, 7812 21-0007-00 TRANSISTOR, 2N3904 21-0008-00 TRANSISTOR, 2N3906 21-0010-00 TRANSISTOR, 2N2222 20-0001-00 DIODE, 1N4002

Page 43

aod O1GAV EF ‘Bur

Page 44

POWER SUPPLY

PART NUMBER DESCRIPTION

90-0094-00 32-0002-00 130-0003-00 90-0017-00 77-0003-04 77-0003-04 65-0133-00 65-0134-00 58-0062-00 45-0012-00 40-0005-06 34-0002-00 31-0001-00 20-0007-00 ASSEMBLY, POWER SUPPLY PLUS 5 VOLT REGULATED POWER SUPPLY ASSEMBLY, TRANSFORMER GROMMET PRE-REGULATOR, PCB BLANK PRE-REGULATOR, PCB CHASSIS, POWER SUPPLY PROTECTIVE COVER, +5 VOLT POWER SUPPLY STANDOFF, PCB TERMINAL, TAB CONNECTOR, 6 PIN FUSE HOLDER FILTER, AC LINE RECTIFIER, BRIDGE

ISOLATION AND DG SUPPLY TRANSFORMER

Fig. 14 POWER SUPPLY

Page 45

OPTICAL SENSOR PCB

PART NUMBER DESCRIPTION

77-0020-04 PHOTO DETECTOR PCB BLANK 77-0020-05 PHOTO DETECTOR PCB 22-0070-00 LC., LM311 21-0007-00 TRANSISTOR, 2N3904 20-0012-00 DIODE, PHOTO (TELEFUNKEN 153P) 13-1062-00 CAPACITOR, 10uF 10-1044-1 CAPACITOR, .1uF 10-1201-02 CAPACITOR, 120PF CERAMIC DISC. 10-6800-02 CAPACITOR, 68PF CERAMIC DISC. 07-0004-00 CAPACITOR, VARIABLE 10K TEN TURN TRIMPOT 02-1032-00 RESISTOR, 10K 02-1532-00 RESISTOR, 15K 02-2222-00 RESISTOR, 2.2K 02-5022-00 RESISTOR, 5K 02-8242-00 RESISTOR, 820K

77 0020 04

10nF ct

RIGHT ANGLE 3 POS. HEADER -100 CENTERS 2N3904 (4x)

Fig. 15 OPTICAL PCB

MISCELLANEOUS

PART NUMBER DESCRIPTION

00-0007-00, CHEYENNE™ MANUAL 49-0069-05, AC POWER CORD 35-0001-00 AC LINE FUSE 5 AMP 135-0024-00 110 AC PROGRAM PLUG 137-0025-00 220 AC PROGRAM PLUG