CATHODE RAY TOMES

Starship 1 TM-085 1st Printing

Starship 1 (Atari, 1977) · Technical Manual · 52 pages · 8 sections · original scan

Page 1

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 2

ft if . Oh io

Page 3

Operation, Maintenance and Service Manual

ATARI INC. 1265 BORREGAS AVENUE PO, BOX 9027 SUNNYVALE, CALIFORNIA 94086 408/745-2000 « TELEX 35-7488

Page 4

All rights reserved. Copyright © 1977 by Atari, Inc. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher.

For permission requests, write:

ATARI INC. 1265 BORREGAS AVENUE P.O. BOX 9027 SUNNYVALE, CA 94086

7F

Lithographed in the U.S.A.

Page 5

TABLE OF CONTENTS

LOCATION SETUP INTRODUCTION ... GAME INSPECTION . INSTALLATION REQUIREMENTS Power Requirements Temperature Range Humidity Range Location Space Required ... Length and Type of Power Cord . INTERLOCK AND POWER ON/OFF SWITCHES . SELF-TEST PROCEDURE IN TABLE 1 ....... OPERATOR OPTIONS IN TABLE 2 VOLUME CONTROL

GAME PLAY A. ATTRACT MODE B. READY-TO-PLAY MODE C. PLAY MODE 0... cree cence teen eee Mayen e AND ADJUSTMENTS CLEANING . : COIN MECHANISM . Components on Coin Door . Access to Coin Mechanisms Cleaning of Coin Paths Adjustment of Coin Switch Trip Wire . Mechanical Adjustments on Coin Mechanism General Troubleshooting Hints .. FUSE REPLACEMENT .. LAMP REPLACEMENT .. REMOVING THE CONTROL PANEL CONTROL YOKE .........-..2+- ADJUSTING THE CRASH CIRCLE REMOVING THE TV MONITOR ..

THEORY OF OPERATION GENERAL INFORMATION 0.2.6.0 eee cece cnet tenet eee eens 21 POWER SUPPLIES CRYSTAL OSCILLATOR AND TV SYNC COUNTDOWN CHAINS . MICROCOMPUTER INPUT/OUTPUT ... Digital Output Inputs ....... VIDEO SECTION STARFIELD CIRCUIT . SPACESHIP CIRCUIT LASER CIRCUIT ..... ALPHANUMERICS GENERATOR. CIRCLE GENERATOR ....... VIDEO PRIORITY CIRCUIT . AUDIO SECTION . ORP> NEW WWWKKNNNNA ammo

ZA™™OSO

™OOR>

ErATS ram

Page 6

LIST OF ILLUSTRATIONS

Figure 1 Location of Voltage-Changing Plugs Figure 2 Location of Power On/Off and Interlock Switches Figure 3 Location of Game Time and Volume Adjustments Figure 4 Coin Door Assembly .......++ 000 cree eens Figure 5 Hinging Open the Magnet Gate Assembly Figure 6 Removal of Coin Mechanism Figure 7 Surfaces to Clean Inside the Coin Mechanism . Figure Removal of Plate Covering Rear of Coin Slot Figure 9 Close-up View of Lubrication Point Figure 10 Detail View of Coin Switch and Trip Wire Figure 11 Adjustments on Coin Mechanism Figure 12 Removing the Cabinet Light Assembly . Figure 13, Removing the PROTON TORPEDOS Pushbutton Lamps Figure 14 Locations of Crash Circle Adjustments . Figure 15 Removal of TV Monitor Figure 16 Starship 1 Game Block Diagram Figure 17 Starship 1 PCB Block Diagram .. Figure 18 TV Monitor Schematic ......... Figure 19 Starship 1 Game Harness Diagram Figure 20 Starship 71 PCB Schematic Diagram ..

LIST OF TABLES

Table 1 Starship 1 Self-Test Procedure Table 2. Option Switch Settings

Page 7

LOCATION SETUP

A. INTRODUCTION Atari’s Starship 1™ is a futuristic one-player computer-controlled game that simulates space flight. The object of the game is to destroy alien spacecraft while maneuvering through star and asteroid fields. A player's score is determined by the number of alien spacecraft destroyed.

You, the owner of Starship 1, have options available in the game. The options are for the number of coins necessary to play the game and whether or not extended play is awarded. These options are selected by removing the game printed circuit board from the metal RF box and setting switches as desired.

Page 8

Starship 1, like all recent Atari video games, has a self-test function that tests approximately 75% of the game's circuitry. By energizing the Self-Test function, you can determine if the game is or is not operating properly.

B. GAME INSPECTION Your new Starship 1 is manufactured by Atari with the intent of being ready to play right out of the shipping carton. However since we cannot be sure that the shipper delivered Starship 1 to you in one piece, we need your cooperation in supplying the last touch of quality control. Therefore, we at Atari would appreciate your following the procedures below to ensure that you are getting the quality of game that you expect from Atari.

  • Examine the external parts of the game cabinet for dents, chips, or broken parts. If you have purchased this game as a new unit, make sure that it looks new.
  • Unlock and open the rear access door. Examine the inside of the game cabinet for anything that appears broken or out of place. Cc. INSTALLATION

REQUIREMENTS

All special requirements for the installation of the game are listed as follows:

Power Requirements: Atari ships Starship 1 for the domestic operation on 110 VAC, rated at approximately 150 watts. The game can be changed to operate at 95 VAC by unplugging the Molex connector plug (see Figure 1 for location of plug) with orange wires (110 VAC) and plugging in the Molex connector plug with black wires (95 VAC).

For those operating the game on 220 VAC (50 Hz), use the Molex connector plug that has red wires. For a location voltage that is less than 210 VAC use the Molex connector plug with green wires (205 VAC).

Temperature Range: Location and storage temperature ranges should be no lower than zero degrees Celsius (32 degrees Fahrenheit) to no higher than 49 degrees Celsius (120 degrees Fahrenheit).

voltage-changing plugs

on/off and interlock switches

Oo

Figure 1 Location of Voltage-Changing Plugs

Page 9

Humidity Range: Location and storage relative humidity should be no more than 95%.

Location Space Required: Starship 1 requires a minimum of 185 centimeters (73 inches) of vertical clearance, a minimum of 75 centimeters (29.5 inches) of width clearance, and 152 centimeters (60 inches) of depth clearance. Depth clearance includes 61 centimeters (24 inches) of minimum player space.

Length and Type of Power Cord: Atari has added a 1.83-meter (six-foot) strain relief power cord to Starship 1. The advantage of the strain relief cord is that if someone trips over the cord, the cord will break off just inside the game cabinet. Tripping over a non-strain relief cord may result in ripping out the insides of a game.

D. INTERLOCK AND POWER ON/OFF SWITCHES Atari had two concerns that resulted in our installing two on/off switches, as illustrated in Figure 2. The first concern was to minimize the hazard of electrical shock while you are working inside the game cabinet. Therefore, we installed an interlock switch on the rear access door frame that completely removes power from the game when the access door is open.

Our second concern was energy conservation. A power on/off switch has been added to Starship 1 so that the game can be turned off during low business periods and closing hours. This switch is conveniently hidden on the right side of the top panel, near the rear of the game cabinet.

Please check for the proper operation of the rear access interlock switch by performing the following:

  • Unlock and open the rear access door.
  • Plug the AC power cord into a 110-volt source. (If the voltage is less than 100 VAC, make sure that the voltage plug is changed to the black plug.)
  • Set the power on/off switch to the on position by flipping the toggle switch toward the front of the game cabinet.
  • Close the rear access door. Within approximately thirty seconds the TV monitor should display a picture.
  • Slowly open the rear access door until the TV monitor picture disappears. The TV monitor picture should disappear when the rear access door is opened to less than one-inch at the top of the door.
  • Close and lock the rear access door. If the results of Step 5 are OK, then the interlock switch is operating properly. If not OK, check to see if the switch is broken from its mounting or stuck in the on position.

E. SELF-TEST PROCEDURE IN TABLE 1 Starship 1 will test itself and provide data to communicate with you that the game’s circuitry and controls are working properly. We suggest that you do the Starship 1 Self-Test Procedure each time you empty the coins from the game’s cash box.

There are three tests perforined with the self-test switch on. The first test is done completely by the Starship 1 computer. In this test, the computer determines if its memory is OK. In the second test, you activate each switch to determine if they are operating properly. In the third test, you move the control yoke to determine if it is operating properly.

The fourth test is performed with the self-test switch in the off position. In this test you determine if the coin acceptors are operating properly.

Perform the Self-Test by following the instructions of Table 1.

F. OPERATOR OPTIONS IN TABLE 2 At this time, decide wha: options are best suited for your location of the Starship 1 game. The coinage options on Starship 1 are 2 games per coin, 1 game per coin, or 2 coins per game. Starship also has a time option ranging from a one-minute to a one-andone-half-minute game.

Set the options of the game as described in Table

  • Refer to Figure 3 for the location of the option controls.

If you decide to have a bonus time option, install the BONUS TIME player notice (comes in poly bag with new game) on the bezel immediately inside the game cabinet above the player controls. Refer to Chapter 3 for instructions for the removal of the front housing assembly.

Page 10

Figure 2 Location of Power On/Off and interlock Switches

Page 11

Table 1 Starship 1™ Self-Test Procedure

Results if Test Passes Results if Test Fails

Unlock and open Coin Door. Set Self- Test slide switch (located inside and to the left of the Coin Door) to the on position.

If test fails, record the BAD ROM number, shut off the game, call your distributor and tell him the ROM failure number.

Note to Distributors: BAD ROM 0 indicates a failure of PROM 1 (location C/D1) or PROM 2 (Location c/D2).

BAD ROM 1 or BAD ROM 2 indicates failure of ROM B (location E3).

BAD ROM 3 or BAD ROM 44 indicates failure of ROM A (location H3).

Press START pushbutton.

Press PROTON TORPEDOS pushbutton.

Set THRUST CONTROL to SLOW.

SET THRUST CONTROL to FAST.

Turn control yoke to left and down, then turn to right.

Pull control yoke up.

Set Self-Test slide switch to off position. Trip and hold in the tripped position each of the coin mechanism trip wires. TV monitor displays almost anything that is normal for the attract or play mode. Test tone is always present from both speakers during Self-Test 1.

Test tone volume increases.

Test tone volume increases.

Test tone frequency is lower than when control is in FAST position,

Test tone frequency is higher than when control is in SLOW. Position.

Test tone frequency increases as control yoke is turned from left to right.

Test tone frequency increases as control yoke is moved from downward position to upward position.

TV monitor displays the word COIN as long as one of the coin mechanisms trip wires is held in the tripped position. TV monitor displays the words BAD ROM followed by a number.

Test tone remains the same.

Test tone remains the same.

Test tone remains the same.

Test tone remains the same.

Test tone remains the same.

Test tone remains the same.

No change in the TV monitor.

Page 12

Table 2. Option Switch Settings

Option Switch Settings Option B A BT

2 Plays Per Coin ON ON

1 Play Per Coin OFF ON

2 Coins Per Play ON

No Bonus Time

Bonus Time

omer Option Switch__$§$» fg] ' (Location K6)

Page 13
NOTE G. VOLUME CONTROL There are six potentiometers on the Star- if voiume is incorrect for your jocation, remove ship 1 Game PCB. Ensure that you know the game PCB and adjust the volume to your desire. which potentiometer you are adjusting. See Figure 3 for the location of volume control. Adjusting the incorrect potentiometer may cost you money.

Game Time

Figure 3 Location of Game Time and Volume Adjustments

Page 14

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 15

During game play, Starship 1 can be described as operating in any of three modes: attract, ready-toplay or play mode.

A. ATTRACT MODE The attract mode begins with the application of power and ends when the proper amount of coins are accepted. During the mode, the T.V. monitor displays four one-line messages. The first line indicates the last player’s score and number of crashes. The second line appraises the previous game performance (for example, YOU HAVE SAVED THE FEDER- ATION or YOU HAVE LOST EVERYTHING). The third and fourth lines are an instruction for the player to deposit a coin to be in command of Starship 1.

Throughout this mode, all controls are inactive.

Page 16

B. READY-TO-PLAY MODE This mode begins when the proper number of coins are accepted and ends when the START button is pressed.

During this mode, the TV monitor displays the following message:

YOU ARE IN COMMAND PRESS START FOR NEXT MISSION

Throughout this mode, all player controls are inactive.

Cc. PLAY MODE This mode begins with pressing the START pushbutton and ends when the game time runs out. Throughout this mode, all player controls are active.

The THRUST CONTROL sets the speed at which the displayed space objects move towards the player. This can be changed from SLOW to FAST or from FAST to SLOW anytime during the game mode.

The player has two ways of destroying alien spacecraft to earn game score points. One way is to line up an alien spacecraft in the laser sights (X mark on TV monitor screen) and then press one of the laser activator pushbuttons located on the end of each handle of the control yoke. The other way of destroying alien spacecraft is to press the PROTON TOR- PEDOS pushbutton. This results in destroying all alien spacecraft that are displayed on the TV monitor. This second method is obviously easier, but a player is limited to five proton torpedos per game.

The control yoke operates just like in an airplane. To operate the control, the player must imagine being in Starship 1 and flying toward the targets. To go up, the player must pull down on the control yoke. To go left, the player must turn the control yoke to the left.

Page 17

Due to its solid-state electronic circuitry, this Atari unit should require very little maintenance and only occasional adjustment. Information given in this chapter and elsewhere in the manual is intended to cover most servicing situations that may be encountered at the game site. The procedures given are in sufficient detail to be understood by a person with moderate technical ability.

NOTE If reading through the manual does not lead to solving the specific maintenance problem, you can reach Atari's Customer Service Department by telephone (open Monday through Friday, 7:30 am to 4:30 pm Pacific Time):

from outside California (800) 538-6892 (toll-free)

from inside California (408) 984-1900

For those interested in gaining more information on video game technology, especially the electronics, we recommend reading the Video Game Operator’s Handbook, manual no. TM-043. This book is available from Atari, Inc., attn. Customer Service Dept., 2175 Martin Avenue, Santa Clara, CA 95050 for $5.00 each, or from your distributor.

ADJUSTMENTS

Page 18

A. CLEANING

The exteriors of game cabinets and plex panels may be cleaned with any non-abrasive household cleaner. If desired, special coin machine cleaners that leave no residue can be obtained from distributors. Do not dry-wipe the plex panels because any dust on the surface can scratch the surface and results in fogging the plastic.

B. COLIN MECHANISM

Components On Coin Door Figure 4 shows the back side of the coin door assembly where the game’s two coin mechanisms are mounted. Included is the lock-out coil assembly; the lock-out wires are connected to this assembly but are hidden behind the coin mechs. During the attract mode the microcomputer energizes the lockout coil, causing the lock-out wires to retract far enough to allow genuine coins to reach the coin box. But during the ready-to-play mode when the LED is lighted and during the play mode (and also when AC power to the game has been turned off)

Slam Switch Assembly

Coin Lock-out Coil Lamp Holder

Figure 4 Coin Door Assembly the lock-out coil is de-energized, causing the lockout wires to move out far enough to divert coins over to the return chute.

Directly below each coin mechanism is a secondary coin chute and a coin switch with a trip wire extending out to the front edge of the chute. When the trip wire is positioned correctly, a coin passing down the secondary chute and into the coin box will momentarily push the trip wire down and cause the switch contacts to close.

Also shown in the photograph is a slam switch assembly. It has been included to defeat any players who might try to obtain free game plays by violently pounding on the coin door to momentarily close the contacts on a coin switch. The slam switch contacts connect to the microcomputer system, which will ignore coin switch signals whenever the slam switch contacts are closed.

Access To Coin Mechanisms To remove jammed coins, and for maintenance cleaning, each magnet gate assembly can be hinged open without removing it from the door, as shown in Figure 5. Or, if necessary, each coin mechanism can be entirely removed from the door merely by pushing

Figure 5 Hinging Open the Magnet Gate Assembly

Page 19

down on a release lever and simultaneously tilting the mechanism back, then lifting it up and out. This is shown in Figure 6.

Figure 6 Removal of Coin Mechanism

Cleaning of Coin Paths

CAUTION The use of an abrasive (such as steel wool era wire brush) or a lubrication on a coin mechanism will result in a rapid buildup of residue.

By talking to many operators, we have found that the best method of cleaning a coin mechanism is by using hot or boiling wateranda mild detergent. A toothbrush may be used for those stubborn buildups of residue. After cleaning, flush thoroughly with hot or boiling water, then blow out all water with compressed air.

Figure 7 shows the surfaces to clean inside the coin mechanism. These include the inside surface of the mainplate, and the corresponding surface of the gate assembly. There may also be metal particles clinging to the magnet itself. To remove these youcan guide the point of a screwdriver or similar tool along the edge of the magnet.

If coins are not traveling as far as the coin mechanisms, you will need to clean the channel beneath the coin slot. To gain access to this channel, use a %-inch wrench and remove all three nuts that secure the cover plate (refer to Figure 8). Removing the plate will provide access to the entire channel. (Clean both surfaces where coin enters the mechanism, as well as the magnet)

Figure 7 Surfaces to Clean Inside the Coin Mechanism

Figure 8 Removal of Plate Covering Rear of coin slot

Also clean the inside surfaces of the secondary coin chutes, but when doing this be careful not to damage or bend the trip wires on the coin switches.

Lubrication. Do not apply lubrication to the coin mechanisms. The only points that may need lubrication (and only rarely) are the shafts of the scavenger buttons (coin rejection buttons) where they pass through the coin door. Apply only one drop of light machine oil, and be positive that no oil drops down onto a coin mechanism. Figure 9 shows this lubrication point.

Page 20

Manually hold down rejection button and apply one drop here.

= Lock-out Wire

Figure 9 Close-up View of Lubrication Point

Adjustment of Coin Switch Trip Wire

In order for a coin switch to operate reliably when a coin travels down the secondary coin chute, the rest position of its trip wire should be as shown in Figure 10. Use extreme care when handling or touching these wires.

Mechanical Adjustments on Coin Mechanism

Coin mechanisms are adjusted prior to shipment from the factory and normally will retain these adjustments tor many months. If, due to wear or other causes, it becomes necessary to make new adjustments, remove the coin mechanism from the coin door. Then take it to a clean, well lighted area where it can be placed in a vertical position on a level surface (such as a bench top). Besides a screwdriver, you will need a set of several coins, including both new and old, worn ones. Figure 11 shows an exploded view of the mechanism and gives procedures for adjusting the kicker, separator, and the magnet gate. These adjustments should only be done by one who has experience in servicing coin mechanisms and who understands their operation. Exe} Correctly adjusted trip wire

Figure 10 Detail View of Coin Switch and Trip Wire

General Troubleshooting Hints The first action is to look tor jammed coins. After these have been removed, examine the coin path for presence of foreign material or loose objects (such as chewing gum, small metallic objects, paper wads, etc.). In cases where game usage is heavy. it may be necessary to clean the entire coin path periodically, in order to prevent build-up of contaminants that can hinder the movement of coins through the mechanisms. Also confirm that the trip wire on each coin switch is intact, and is properly adjusted, If troubles still persist, check the conditions and positions of the lock-out wires, and the mechanical adjustments on the coin mechanisms, before suspecting the electronics. If a coin mechanism rejects genuine coins, try to readjust it. If this is not successful, then replace it with a working mechanism.

C. FUSE REPLACEMENT Starship 1 contains four fuses, two on the power supply assembly and two on the TV monitor assembly. These fuses are all easily accessible through the rear access door. Replace fuses only with the same type of fuse as follows: TV Monitor Fuses 3AG 1-amp slow-blow, 250 volts Power Supply Fuses 3AG 2-ainp sluw-biow, 250 volts

Page 21

ITEM IDENTIFICATIONS 1 Kicker and Separator Screws 2 Washers 3 Kicker 4 Separator 5 Gate Lever Spring 6 Gate Pivot Pin 7 Mainplate Assembly 8 “C” washer 9 Rail 10 Gate Assembly 12 Cradle Assembly

_/, 18 Upper Gate Pivot Spring 14 Undersize Lever Assembly 15 Magnet Gate Assembly 16 Magnet Gate Adjuster 17 Retaining Screws 18 Coverplate Assembly 19 Return Coverplate 20 Coverplate 21 Mounting Studs 22 Lower Gate Pivot Spring 23 Coin Release Lever

Kicker and separator

  • Set the acceptor with the back of the unit facing you in the test position.
  • Loosen the kicker and separator screws (1) and move the kicker (3) and the separator (4) as far to the right as they will go. Lightly tighten the screws.
  • Insert several test coins (both old and new) and note that some are returned by striking the separator.
  • Loosen the separator screw and move the separator a slight amount to the left. Lightly retighten the screw.
  • Insert the test coins again and, if some are still returned, repeat Step 4 until all the coins are accepted.
  • Loosen the kicker screw and move the kicker as far to the left as it will go. Lightly retighten the screw.
  • Insert the test coins and note that some are returned.
  • Loosen the kicker screw and move the kicker a slight amount to the right. Lightly retighten the screw.
  • Insert the test coins again and, if some are still returned, repeat Step 8 until all the coins are accepted.
  • Be sure that both screws are tight after the adjustments have been made.

Magnet gate

  • Set the acceptor with the front of the unit facing you in the test position.
  • Turn the magnet gate adjusting screw (16) out or counterclockwise until none of the coins will fit through,
  • With a coin resting in the acceptor entrance, turn the adjuster in or clockwise until the coin barely passes through the magnet gate.
  • Test this adjustment using several other coins (both old and new) and, if any fail to pass through the magnet gate, repeat Step 3 until all the coins are accepted.
  • Fix the magnet gate adjusting screw in this position with a drop of glue.
  • Remove the transfer cradle (12) and the undersize lever (14).
  • Use a pipe cleaner or similar effective cleaning tool to clean the bushings and pivot pins.
  • Replace the transfer cradle and the undersize lever.
  • To be certain the coin mechanism is completely free of any residue, place the mechanism in a solution of boiling water and mild detergent for several minutes. Carefully remove it and let it air-dry completely before reinstalling in the door.

Figure 11 Adjustments on Coin Mechanism

Page 22

REPLACING THE BLACK LIGHT TUBE

Remove the Front Housing Assembly as follows:

  • With a 7/16-inch wrench, reach through the coin door and remove four %-20 hex nuts, one at each corner of the Control Panel Assembly.

. Disconnect the harness connector from the Control Panel Assembly, then remove the Control Panel Assembly.

With a 0.125” hex wrench, remove three #10-32 x 1inch buttonhead screws and the metal seam cover from the top of the Front Housing Assembly.

. Lift off the Front Housing Assembly.

. With a Phillips-head screwdriver, remove two #8 x 1.5-inch wood screws from each side of the Display Light Assembly.

. Pull Display Light Assembly out of cabinet far enough to remove the black light.

Re-assemble the cabinet, performing steps 1 through 6 in the reverse order.

DISPLAY PLEX GRAPHICS PANEL

\__contaoe PANEL ASSEMBLY

REPLACING THE FLUORESCENT TUBE

  • Remove the Display Plex Graphics Panel by using a 0.125-inch hex wrench to unscrew five #10-32 x 1-inch socket head screws.
  • Remove the fluorescent tube. ‘METAL SEAM COVER

U7

ISPLAY LIGHT ASSEMBLY

RONT HOUSING ASSEMBLY

Figure 12 Removing the Cabinet Light Assembly

Page 23

D. LAMP REPLACEMENT Starship 1 contains five lamp: two PROTON TORPEDOS pushbutton lights, and a coin-door light. Cabinet lighting is done with an eighteen-inch fluorescent tube and on the back bezel with an eighteen-inch black light tube. Both the fluorescent and black light tubes are mounted in one lamp assembly. To remove the lamp assembly, follow the instructions in Figure 12. binet lights,

There are two lamps (Chicago Miniature type #328) in the PROTON TORPEDOS pushbutton. These may be changed by reaching through the coin door. However, if you have had a bad day, you might consider removing the Control Panel Assembly first. This will eliminate the aggravation of working with these tiny bulbs ina tight space. Figure 13 shows how to replace these lamps.

E. REMOVING THE CONTROL PANE Removing the Control Panel Assembly can easily be accomplished through the coin door. Reach in with a 7/16-inch wrench and remove the four % x 20-inch hex nuts, split-lock washers and flat washers at each corner of the Controi Panel Assembly. Remove the Control Panel Assembly. F. CONTROL YOKE The control yoke has two p: potentiometers supply player steering information to the game PCB. With a good amount of use, these potentiometers may eventually become dirty and require cleaning. To clean, use a tuner cleaner. This isa spray cleaner that is available at most electronics supplies stores. When you buy tuner cleaner, make sure that you get the long nozzle extension tube that comes with the spray can.

For cleaning the potentiometers, remove the Control Panel Assembly (see Figure 12). Insert the spray nozzle extension tube into each potentiometer, spray, then work the control yoke to make the potentiometers rotate.

G. ADJUSTING THE CRASH CIRCLE When Starship 1 crashes into another spacecraft or into a planet, an explosion occurs and a crash scene appears on the TV monitor. The crash scene isa circle of negative video. This circle is derived froma complex analog signal which is size-, shape- and position-adjustable.

‘CHICAGO MINIATURE TYPE #328

Figure 13 Removing the PROTON TORPEDOS Pushbutton Lamps

Page 24

To adjust the circle, set all four toggles of DIP switch S2 at location B8 to the on position. This will result in the display of all or part of a circle. Refer to Figure 14 for the location of the Circle Generator potentiometers VRAMP AMPLITUDE, H POS, V POS, and DC OFFSET. Adjust potentiometers H POS (horizontal position) and V POS (vertical position) to center the circle. Adjust potentiometer V RAMP. AMPLITUDE for a round circle. Then adjust potentiometer DC OFFSET for a circle with a diameter that is about 2/3 the horizontal width of the TV monitor. After you have adjusted the circle, set all four toggles of SW2 at location B8 to the off position. This concludes the adjustment.

H. REMOVING THE TV MONITOR The TV monitor in Starship 1 may easily be replaced. This is accomplished by opening the rear access door, unplugging the Molex connector from the monitor, removing four securing screws, and sliding the monitor out the back door. See Figure 15 for the location of the securing screws on the monitor.

V RAMP We

DC OFFSET

Vv POs

Figure 14 Locations of Crash Circle Adjustments

Page 25

Remove Screw.

Remove wood screws.

Reach through coin door and remove two securing nuts (and screws) from front of TV shelf assembly.

Unplug Molex connector from TV monitor chassis.

Lift back of TV shelf assembly and slide out of cabinet.

Figure 15 Removal of TV Monitor

Page 26

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 27

THEORY OF OPERATION

A. GENERAL INFORMATION The block diagram of Figure 16 shows the major controls, circuits and outputs of the game. Figure 17 is a block diagram of the Starship 1 game PCB.

The game’s television monitor is a self-contained transistorized unit. Because the composite video signal sent to the monitor differs in many respects from the signal derived from commercial TV broadcasts, the picture appearing on the screen is unlike that of a home TV set and the monitor does not produce any sound. See Figure 18 for a schematic diagram of the TV monitor.

The game’s composite video signal is made to produce only four video levels instead of the more or less continuous shades of grey seen on a home TV screen. The background of the picture is black video level only, but game objects may use any of the four video levels.

Page 28

On the game PCB schematic diagram, Figure 20, the symbol “‘P” (appearing at various inputs of integrated circuit devices) indicates a connection of +5 volts DC through a pullup resistor. For easy reference, the game PCB is divided into grid sections. Along the short side of the board these sections are identified by letters A through R (skipping letters G, |, O and Q because they may be easily confused with the numbers 6, 10, and 0 respectively). Along the long side of the board the numbers 1 through 12 are used. For example, sheet 1 of Figure 20 illustrates the type-MC1495 analog multiplier F11 at the lower left of the drawing. This device F11 will be found at coordinates F and 11 on the PCB.

Figure 19 is a harness schematic of the entire Starship 1 game. This figure illustrates how all electrical and electronic assemblies are electrically connected together.

B. POWER SUPPLIES (lower right corner of sheet 1, Figure 20) The two AC voltage inputs to the board come from the 25 VAC and 16.5 VAC center-tapped secondary windings of the power transformer inside the

ON/OFF

INTERLOCK SWITCH

SWITCH Ac souace L—ve Power Supply Assembly. The +5 volt regulated supply provides Vcc for most of the board’s integrated circuits. The +12 volt and —12 volt regulated supplies provide lower-current voltages for analog circuitry on the game PCB. The unregulated +18 volts connects to the audio driver stage for the game’s audio output.

Cc. CRYSTAL OSCILLATOR AND TV SYNC COUNTDOWN CHAINS A 12.096-MHz crystal oscillator (sheet 1 of Figure

  • generates the basic clock frequency that is divided down to produce the TV synchronization signals. The signals used to produce a TV monitor raster consisting of 262 horizontal lines at a horizontal frequency of 15,750 Hz (256H). Synchronized with line 240 is a vertical blanking pulse that occurs for the duration of 22 more horizontal scans, resulting in the total number of 262 lines per picture frame.

Besides being used for the TV raster, the TV timing signals are also used in the motion circuits, in the alphanumerics display circuit, in the phasor generator, in the microcomputer clock and in various other places on the board.

GAME LIGHTING

GAME PCB

Figure 16 Starship 1 Game Block Diagram

Page 29

D. MICROCOMPUTER The microcomputer is the control center for the action of the circuitry that makes up the game. The microprocessing unit (MPU) send out addresses on its address bus and accepts data or outputs data onto the data bus. When the MPU is reset, by receiving first a low level and thena high level on its RESET line, it outputs addresses that cause the program memory to put data onto the data bus. The MPU reads this data and uses it to address the main program.

The program instructs the MPU what operations to execute and at which address to execute them. This controls the flow of data on the bus and “‘reads”’ inputs and “writes” to outputs. Data may flow into the MPU from program memory, “zero page” read/ write random-access memory (RAM) and through the transceivers from the Data In bus (D1N7 is one line of this bus) which comes from the data input selectors.

Data may flow out of the MPU to zero-page RAMs or through the transceivers to the Buffered Data bus (BD7 is one line of this bus) to the following output interfaces: the message RAM, the digital output section, the digital-to-analog converter (DAC) section, and the position RAM in the motion circuitry.

The interrupt request (IRQ) line of the MPU comes from the coin switches. If the line stays low rather than pulses low, it will cause the game to display “COIN” on the screen, indicating a broken line, bad switch or jammed coin mech.

E. INPUT/OUTPUT Digital Output The digital outputs of the MPU consist of decodes and data outputs. The decodes respond to various outputs of the address bus and enable the appropriate sections of the circuit to become active. For example, the state of the address bus can determine if the player up/down control is being sensed, or if alphanumeric messages are being output.

Digital outputs or control signals, such as PHASOR ON, are levels or pulses required to perform various tasks to output game video and audio,

Decodes also enable the transceivers to transfer data from the Data !In bus to the Data bus, or to put data from the Data bus onto the Buffered Data bus, or to be put into an off state (so that data is input from program memory or zero-page RAM) or output to RAMs. Address buffers are merely digital followers to provide enough power for the addiesyes tu fully drive the TTL loads on the Buffered Address bus (BA9). The Buffered Address bus always exactly follows the Address Bus (AB9) from the MPU.

Analog output is produced by the Digital-to- Analog Converter (DAC) that produces a string of analog voltages corresponding to data on the DAC input. This string of values is demultiplexed to individual voltage level outputs by the analog demultiplexer. The signals are spaceship size (SSSIZE), noise amplitude, tone pitch, motor speed, circle horizontal (H POSITION), circle vertical (V POSITION), and circle size.

Inputs Analog inputs consist of three voltage levels: up/down control, left/right steering, and game time. These go to the Analog-to-Digital (A/D) converter. A fourth input, a feedback line from the DAC, is not used. The Analog multiplexer (N11) selects which source to input to the comparator (L11). When the A/D RAMP voltage passes the level of the selected input, a flip-flop (F7) clocks in the change and causes another flip-flop group (J7) to clock in a digital value corresponding to the level. This value is then input through the digital input selectors.

Digital Inputs are chosen by the selectors (E6, F6, J6 and H6) according to the address the MPU outputs. Sources for the inputs are the D/A value, game digital logic inputs (such as RDATA4 or EXPLOSION), game option switches and game cabinet switches. The switches are start, coin 1, coin 2, test, slow, laser and the proton torpedo switch.

F. VIDEO SECTION The video section consists of the circuits that generate the video and the output area which assembles the composite video signal. The microcomputer writes data to the motion RAMS (J4, K4, 14, M4 and N4) to specify the objects and directions of all motion objects.

G. STARFIELD CIRCUIT The starfield generator is a two-shift-register noise generator (D-E5) to produce the fixed starfield and the “grain” seen in the planets.

H. SPACESHIP CIRCUIT (Patent Pending) The spaceship circuit has a voltage-controlled oscillator (VCO, at E11); the VCO produces a clock to

Page 30

run counters that address the ROMs containing the spaceship pictures. If the VCO runs fast, the counters count through the picture very fast and the resulting picture is small.

Asa spaceship grows in size, the frequency from the VCO becomes lower and objects appear larger.

I. LASER CIRCUIT The laser circuit is fired by PHASOR ON and produces the signal (M6, N6) that makes the laser apear in the video.

J. ALPHANUMERICS GENERATOR Messages are stored in RAMs K7 and M7 and are output by sync functions which address the alphanumerics ROM, N7. This data is loaded into shift register P7 and shifted out into the video.

Adressing of the RAM is controlled by selectors K8, M8 and N8 which use sync functions to display the RAM, but use MPU addresses to write into the RAM.

K. CIRCLE GENERATOR The circle generator begins with a current source to bias Q1, Q2 and Q3 to produce the following ramps: A/D RAMP; H RAMP and VRAMP. A/D ramp is only used in the analog input section, not in the circle. The H.and V ramps are each adjusted to cross zero, then are multiplied (multipliers F11 and J11). Then they are summed and fed to comparator L11 which decides whether the video is scanning within the circle.

L. VIDEO PRIORITY CIRCUIT All video comes to the ROM R10 which gives appropriate priority to all video. Outputs are through Ril to form the composite video containing sync blanking and all images.

M. AUDIO SECTION The laser generator is a 556 located C10 used to produce the distinctive laser sound. Noise is generated by the shift registers B9 and C9 and is fed to the £10-D11 noise filter. This filter produces different sounds for the ‘‘whoosh” of a planet, the crash and the explosion. The motor sound is made by a 566 at A9, and its level is controlled by the signal MO/LVL. Variable tones are produced by the 4136 (at E10) and the 555 at B10. Level control is provided by SL1 and SL2. All audio is summed at the volume control and goes to the TDA1004 audio amplifier and from there to the speakers.

Page 31

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 32

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 33

sranrewo

cts es A

Pe 10 speaens

Figure 17 Starship 1 PCB Block Diagram

Page 34

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 35

Figure 18 TV Monitor Schematic ots Ste swig 018

al cities Bi ae

  • a ale

Se

Page 36

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 37

MONITOR | 03 ou Doe peor ee Tl crest FLUORESCENT on oa LIGHT

mee=)BE
FORPOWER SUPPLYLoot:[efeaten=
SCHEMATIC.ie.~of]ww
007197-01pepteBLACK LIGHT

A 3pWw

re

twmf!04brbo

BPH F5 fo fo pute fufepedngy -

'

i

Hl i d f

[elevpee)COIN:
'-COUNTERLocKouT |
poy &ite}COIL
LAl en/e'23)SLAM
species|COIN SWITCHES Y%
iOlWtD

OR/

HORNexomCol|#2Eea)&
7OR[OR/BKalx©
B| BK/YOR[neaHNo}OG
ine}BO)fone]
9]BK1i)

Se ee a || so] Y ui) GY

x2] GY 13] BN wf Few

wo]|enee,

Figure 19 NOTICE TO ALL PERSONS RECEIVING THIS ORAWING CONFIDENTIAL, Reproduction forbidgen without the Specific written permission of Alar. Ine. Sunnyvale California This drawing #8 only conditionally resued anc neither receipt nor possession thereo! confers or iransters| any night in. or license to use, the subject matter of the Grawing or any design oF lechnical information shown thereon sor any right te reproduce ths drawing or any par! thereat excepl for manulactore by vendors of Alar Incor porated and lor manufacture under ine corporation s wi fen license. no righ! to reproduce this draning granted at the subject maller thereol unless by written agreement sh of willen permission from the eorporalion

Starship 1 Game Harness Diagram (Sheet 1 of 2)

Page 38

TRANSF¢ NOTICE TO ALL PERSONS RECEIVING THIS ORAWING

HOV VOLTAGE OR SELECTION [- BLOCK | SHOWN

i OUT

AC INPUT

Page 39

PCB AOOL555-01 MR7SO coes)|

Ee

TP INTERLOCK

SWITCH

ON/OFF SWITCH Bke/wl oo = BK

POWER SUPPLY SCHEMATIC

Figure 19 Starship 1 Game Harness Diagram (Sheet 2 of 2)

Page 40

SYNC GENERATOR

wisene |

are [aw],Lk7

[pape AE] | | more seer Soe glo ly, 2ardtsverave

£2? sapcanialoe ©we s7ecae

seem 2 seer TSK R yl a), MY aaf2—f evaeser

supe eeepvaeo SUMMERela: 8Es
  • =I voto Proes TP ai ° 2223
sienpe? Tah-5RaS
2weo
His2 zeZz,6Spe yee[sta.
ven BEEsoeASPesDee

vacene on BAR jg ALPHA: NUMERICS Se enna

is8e Ks PUi Bfote[:

%

oo ee 8w SheiS
siey So igay NTT]fen neolsfc

t 2 »

tie2Boeon
1TEDweFYSaar
vents] xD2aet

jens g

1 13a) )e2 > EE9L

a ‘ns can Lilo ses c seh EDA se, oune —EE eae, ——hag— ome ae — * aft 6 hn s ale tev rs a) > Hn:

aise2ee
Ig2* CIRCLE GeENERSTOR& fsaring

meg fe 5 the

eaSloe &BAO ——SSHaw_

ROM A i Alex

ip,swers
ZR2Ap RaveDP ow

sa

raworeB32:
gemenLS-— INDICATES SHORT LEAD LENGTHS REGVETe RE SEE aw
‘BIAS,bolstom ALIN,4
Rae ulfee3304 position:5
Vo TewRet$

se mon

Okeveosino3

®

4 SYNC:mc ideshs

sano IPO rome f

bag)4Sv vd I,

cane | iseL i

a = EMPOT Blog ose ae a wer beak] San po

eetfox aSERS MRad.

2} venue va) Mees tt

Ros ALE

o* [sep omer

Page 41

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL Reproduction lorbiiden wiltiout tne Speuiine whiten perimimsion oF Atal anc. Sunnyvale California’ This drawings only condiorally issued. and either recerpl nor possession thereol conlers ar translers any right in, oF license 19 use. Ihe subIect matter of the drawing or any design oF technical information shown thereon narany night to reproduce this drawing orany part thereot. except for manutactute oy vendors ol Atat Ineor porated and for manufacture under the corporatan s writ len icense. no night to reproduce thisdrawingisqianted or Ine subject matter thereot uniess by written agreement with oF written permission from the corporation,

~ aupio ourpur—

SPeateR

  • seage

—sveyne

verena

Blo.” aE apa womenies co Hoses af asen or ise! — eeu! AARPIELD RES] by 114 gc}! STARFIELS FES Caw RES Ao, Gy! SPASESHIP RES

ebe 8s

vee

01 version ont 4 ger

Fare 00753)

g oe? Dee bes bea bes ez bat vee

-O1 VERSION ONLY Tow ers

Powe SUPPLY

tay ue Ghee [Z BES 3 aso? aie aie ancy oI

totfelTI}oe
‘dlalee
ItTeasLersenaien,Tip

sol th Ze AE NE 82,8 3.27-823

ma7so |OKaoeeeBabesEA

ieee fr ay pase

t ns aS 2 ey

poy

cee ton

a

slers io

wtow

Figure 20 Starship 1 PCB Schematic Diagram (Sheet 1 of 3)

Page 42

9f Nousauia voussoa Winaziuon awe =a = al ei Cen —

ow ie08 woILwanwoe emrumbenng 2h tlm |u te fees 4 Whar ages ee oan “2 3957 2 iar iva g xe 0 98 en a ig wos a Eee mae om oS wna arsises —]8 Ke [ + (a ranas +8 aE rarrenitg S t way (— savas an ve ANS H spent now at aReavas

Page 43

NOTICE TO ALL PERSONS RECEIVING THIS ORAWING CONFIDENTIAL Paproduchon forbidden without the specific writen permission of Atari ine. Sunnyvale California This drawing 1s only conditionally issued. an nther receipt nr possession thereol confers or ransters any right in oF license tO use the subject matter Of the ‘irawing oF any design or technical iaformation shown thereon. norany night to reproduce this drawing or any part Imoreot except for manufacture by vendors ol Atat incor

wives

HvrPrRSSC amen |

7[iesur exp —2fh,of

ran —— 35 20 | TE nas

uoTe{s 2 = HYaR,2cmeaen—4}sBSR
“Zee|ehe8 oft
>aBiam4tre|
.= 7Edeers Cat=“ ee4
4recestepfeePeout |
>cermeur cen LES)TRg7|wee

—e] “oes

stannieyael

L 2 ae OG go tt 7 2 comp BLANK

Puascie9 omPrat)SELESox

he elas e ce 4d

tev

A PosiTiOn. seri scree mise y

FBCARK x5 PLACES i

ATH je mare

wom C2} RTE

pre,

BEET OHPLAY

INTAL POSTION

Tio DeTECT CERRY

Aor L_sprapt PAS

rs

Pa

ar R58, Pr 4 sey pers He eLANK. SERED RS nib — SPACESHIP RES

oe ac

12 Fconr Stan

Figure 20 Starship 1 PCB Schematic Diagram (Sheet 2 of 3)

Page 44

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 45

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL Reproduction forbidden without Ihe specific written permission of Atart Inc. Sunnyvale Calinrnia This dtmwina re nny enaditianaliy eed ant neutner receipt nor possession Inereot! contersor tanslers| any night oF license to use the SuBject mater of he Srawing oF any design or technical information shown thereon nor any ngnlto reproduce is drawing or any part thereat except for manufacture by vendors of Alar Incor BESS map porated and for manutacture under the corporation $ writ re) 4)3.2,1 0.8 W en ticense no nightie reproduce his deawing granted oF ERE Ror the subject matter therect unless by wrilten agreement

ve[MSALPHANUMERICS WRITETHwith or written permission Irom the corporation
We “Putps | Me OY Shactwie Stan noonTetaap

ex y wpe wenonttl Stats SST See las Uepuasah TRACER a GCE SHIP TE STARFIELD RESET s 4g Coon Cate eset so

Peesan,4 Satoejesse
ifsBEL¢ Rgeespe$4
Topiason32Te Rowe eetPo Bie se" $= ethenessw
gebustsarkFooagcom 2A ga a

(03 - START, ton ’

oexxx)+ Annee out

es +. pour see Fe eee: 218s SS eto fg

.$0 TOME era5. Uae omerRa?Jma
‘ATTRACTAAA8
'netei

ees ; Es weurs

=eesi
eo)Be:
eeehaw,BRT a3 se [rren!
sfRoP“oy1
Eefeifr\
Pp a‘aee "rou
RoscS,=

geen irene (oR

“e 1 CIRCLE GEN7_+ Sv
S¢ expiosionet19,2.7K
nTSonrmo. oureursEpopetvoor receES
CESHIWE0 peeAIee
seaceomir| YBS00 noe FRET eoGame tine

baa oy 7 egy

Bal hyFhca Hg=28 mow S
Seeaeer>ons

, cont Ses. | —§

Erkennoue wey Srarrme niu were ee See ERP

seoite NOISE AnpaTuoe TONE AIreN ss,

220" MOTOR SPEED

DACIN

Figure 20. Starship 1 PCB SChematic Diagram (Sheet 3 of 3)

Page 46

Wy WWHLNIGLINOD.

90-Go10 ‘ONIMYHG SIL ONIAIZOI4 SNOSYSE TTY OL 3DILON

aut inowne voperao)

COT LUE

Starship 1° PCB (Sheet 1 of 3)

Page 47

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 48
Tem [Part NaberDeseriotionTem | Part Nonber‘Bescription
as | 2e-2so1081 |) ean. etece tar 25cnsso

ai | seeansis 1 |] transsstor, ans00

as | r4-asozasid:a.aue 290oe*
.eaenfar-r002 |] ac. 2600conf
aa | 242502271+ aanue a9v©.coeni0,r10
na | aera0n2 |] rc. r402none
as | 24aso0n2 || cap. etece e700 25073,0
as | ar-re08s |] = 408£7.97.69.9 4
so | ze-asozxefanatcatan
ye | 7-70612406wo
si | aeasciefa |] ©anmue =om'
m7 | arowo |}1408£2,82,02,86,25.87,
sz | arasmor | || cap, cer vise .otut ase99,54,56,61-79,86nS aka
si]grasmne | 52 || =ovtur asea-5,6019,22,23,27rs | arto1 |[ + sa8

43, Valea, 48-50,

52157,$8.63065.67,a | areaa |] - saeFo

Fol79, 7486.87.09,

ca | apasozaposeeo | sre0n7420°s
:-wae?n7abe
ss | zrrsom[acote *es
e2 | waneL220es
se | zetorion[1 |P capy pinned mica topt voye20
|aeraasvd]sae2
aeee|
ea | ota.vane2600790 8, 80.89
se}reinefa:pipe toy77*
es | sramsarfa |] = satsassae
so}ronfa:oope toa625, 26,72
we | sr rensas | araises6.06
co}reammfa+gnqpe toneen
evaesonez[a |] *= © ronone tow66.:el
se]37-20071vaiove
ee | eerfa]Z2opt awovcan

ea | srausiss | 5 |) © aatesy £2. F6.H6.08

es | 20101 |] cap, taneatum 2.206 necon
vo | osermsisr | apasts?a 8,H0.¥8

64 | 20-001 1 |] can, poiyearton, .oa7ue,bov,1 05s

|amass | |] + sanePana, F5, 18,08,
6 | nina — | o0 |] soe, amare8-9 162 | amvacies[a |] = oaenes05.85,89.09
er | sustneon | 4 || diode, ineoorcmaasor | ansasira | 6vusita2 ,42,72,99.88
eooe | ay-rausissais0
69 | aa-anacea | 2 || rransaseor, 2nsoaeonos | seretsisa[a||» ratsinsiviesait
no | aeeanoss | a || ranesstor, maneauras | mermesis | 2yausi9s5.07
or | s-7e298222208r55
Tem] Part Nonber [5DescriptionTem | Pan Nonber 7 @5-]Tescciion
oe | a7-ss51 | ee. 558moree]eetiaert | 2 |) eipawiten, aner tomy caw ayRO,
oe | sess6a || - osecoar]aonnaa1 |] cevsten, 12.096 mza
roo}37-566166aze | 79420901 || socket, 49 F8nes
rr]s7-x00811408”x20]m-osoce1 || mearssni, siaoos
roe]a7-1952lf 1a9sFulx0 | 78-26081 || siteea
res}a7-75107rn |mnri]72-26062 |] sores, mach., Pan ti. PRL 86-32 x 4 Cres
ros]a7-aanaamus1,06az]016s5 |] Wesker, raat v6
aos]97-99212saatauedrn]reo562 |] waster, took, tne Star a
roe | a7-aa382oecaera]r91602 |) wat, nox, ws-32 exns
aor]a7-a6o21002ssas]aacaaoe | avn |] coment, uar004 Heat sink
ann]37-20011sooanis|—aorsior | 1 |] eran, atpnetonertes
ree]ar-arae2eranvaraan]oommemfa |synew
no]ayane1anneunase}commenfaomteceus
ant]sreratooe | 1 fpr. ame eoatonamre]oomiem — | aSpacesnits 22ft
riz]argos2 |] aes aonanePeSpaceship 21"
na]saae2aiss1oi2ran}oorsieor |wadeo ontputno
nis]a wcanow |mossieppuraz]oorsimm | 2naaronsns
nis]sue1 || eoutetor waa29ae
ne2 || coutator «rv 7m20rea]0752002 | a || Program Rew 3000»
wy1 |] sesstator -ia¥ 7912covas}oorssi-or | 1 || proacan mum 28002
ae]oorsze-o2 | 2 |] prom. program 2¢00-0cm
us}aresv |] ac. m5on
ua]aovsaneoz | a |) prom, peogran ze00-cpr
nsras]0-0721 || pes, canton, 4, 5, 2.7 On NIE
120]90-60101 || ne21a
10 | eni021 |fres, eine, ww, 1, 2-00 ohma6
rai]90-70055 || mam. nase14,8, U64Fim, WwIs,
ri | 1a-n62aie=" eo omaes
122]90-7022||mom, 2517pa.ma9.P3.R83
123]90-70182 || ras, niowa-2sou
rea]s0-70192 || saw, antinspct

as

Starship 1° PCB (Sheet 3 of 3)

Page 49

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 50

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 51

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 52

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.