VS TKO Boxing
Vs. T.K.O. Boxing (Namco / Data East USA, 1987) · Document · 12 pages · 10 sections · original scan
vs. TEO BOXING
for
Nintendo vs. System, vs. DualSystem, and Table model games
INSTALLATION & SERVICE MANUAL
470 NEEDLES DRIVE SAN JOSE, CA 95112 TELEPHONE: (408) 286-7074 ) fa DATA EAST USA, INC.
780-0071-00
FCC WARNING: This equipment generates and uses radio frequency energy and if not installed and used properly, ie., in strict accordance with this Instructions ganual, ay cause haraful interference to radio communications.
FBI WARHINGs Federal Jaw provides severe civil and crininal penalties for the unauthorized Teproduction, distribution, or exhibition of copyrighted audiovisual works and video gages. The Federal Bureau of Investigation investigates allegations of criminal copyright infringement.
TRADEMARK NOTICES VS. TKO Boxing {s Trademark and Copyright Namco LTD and Data East USA, Inc., all rights reserved. Developed under license froa Nintendo for play on the VS. System,
REPLACEHENT PARTS AND SERVICE:
To obtain replacement parts or technical assistance, contact the oe during the hours of 8:00 am to 5:00 pm Pacific Time at (408)
authorized Data East distributor in your area, If you require referral or further technical assistance, you say contact Data East’s Customer Service
7074,
[ TKO BOXING j
INSTALLATION & SERVICE MANUAL
TABLE OF CONTENTS
1, INSTALLATION INSTRUCTIONS
A. Before you Begins. .csscsecseceseeeeeseeeeeseneseseens eeeeed
B. Graphics......seeeseeee peeeeeneee Seeenneneeaee Sbeeeeensaae 1 C. Sub-Board.... cee ccsecseeseeeee sees een ene e eee n ee eneeee ees 3
2, GENERAL INFORMATION
A, Operator Selectable OptionS.......ccsssseceeessseeeeseeeee 4
B. Sub-Board OptionS......secseecscereseeeeseeteeseeeees seened
C. Warranty Information. ..sscssceesseeceseeeeeeteeeeteeees 6
Copyright 1987 Data East USA, Inc. 470 Needles Drive San Jose, CA. 95112 (408) 286-7074
Manual Part Number: 780-0071-00 Ast printing: 09/30/87
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Betore You Begin.
Thank you for purchasing this Data East product. This game pak is intended to be installed into any Nintendo Dual-System, Uni-System, or VS. Table-System video game. Check your pak for the components listed below.
| 1 | ‘SUB-BOARD, TKO BOXING | §20-0089-00 |
| 1 | NAMEPLATE OVERLAY | 800-0034-00 |
| 2 | HEADER STRIPS, UNI-SYSTEM | 820-0062-00 |
| 2 | HEADER STRIPS, DUAL-SYSTEK | 820-0043-00 |
| 1 | GAME INSTRUCTION SHEET, TABLE-SYSTEM | 406-0071-00 |
| 1 | INSTRUCTION MANUAL | 780-0071-00 |
Remove the marquee glass or plex from the cabinet and carefully remove the Nameplate Overlay. VS. UNI-SYSTEH ONLY: Install the two top and bottom Header strips to the back of the marquee glass or plex as shown in figure 1.
VS. DUAL-SYSTEM ONLY: Install the Header strips to the right and left rear edges of the glass or plex as shown in figure 1.
Tape the Nameplate Overlay to the Header strips and re-install the glass or plex into the cabinet.
VS. TABLE SYSTEM: Remove the Instruction Plate and replace the existing instruction label with the TKO Boxing Instruction Label as shown in figure 1.
VS. TKO BOXING PAGE 1
VS. UniSystam™ ‘VS, DualSystem”™
NAMEPLATE OVERLAY
Figure 1
The VS. TKO Boxing game utilizes a Sub-Board pcb which mounts to the Nintendo MDS pcb and allows the use of larger capacity memory devices in
the Nintendo System. Install the Sub-Board using the procedures specified
ow.
- Remove the Nintendo MDS pcb from the cabinet.
- Remove the existing game program Eproms, PPU, and CPU chips from the side you wish to instal! the Sub-Board (see specific information below).
- Carefully bend down the Capacitors on the Nintendo MDS pcb at locations
c3, Chl, bso, and C47 to prevent them from touching the Sub-Board and from locations 6A, 6B, 6C, 6D, 8A, and 8B. Remove the PPU and the CPU
causing a short circuit. UNI-SYSTEH: Sub-Board must be installed on the SUB-SIDE, remove Eproas
from locations 8F and 8J.
DUAL-SYSTEM: The Sub-Board can be installed on the HAIN SIDE (Left Screen) or the SUB SIDE (Right Screen). Remove only the Eproms, PPU, and CPU from the side that you select.
PAGE 2 VS. TKO BOXING
Position the two 40 pin headers protruding from the solder side of the Sub- Board into the respective 40 pin sockets on the Nintendo MDS pcb. Usin the palm of your |» apply pressure down on to the Sub-Board until i seats securely into the Nintendo MDS pcb’s sockets. Install the CPU chip removed from the Nintendo MDS pcb into the CPU socket of the Sub-Board.
Install the standoff and retaining screw to ensure proper contact between the Sub-Board and the Nintendo ADS pcb as shown in Figure 2 to coaplete the installation.
INSTALL SPACER HERE
INSTALL SPACER HERE
SUB-BOARD SPACER “MDS PCB
Figure 2
VS. TKO BOXING PAGE 3
GENERAL INFORMATION |
Operator Selectable options.
The KO Boxing game containg game play options selectable by changing the
settings of a Dip-Switch Bank on the Nintendo MDS pcb. Use SWI if you have Installed the Sub-Board on the MAIN SIDE, and SW2 if you have installed the Sub-Board on the SUB SIDE. The available option settings are shown below in Table !.
- To change the Dip-switch settings, remove power to the game, open the tear access, and remove the Nintendo MDS pcb from its cage.
+ Change the switch positions to the desired settings. + Re-install the pcb into the cage, making certain that all cabling is plugged in properly and secure.
- Apply power to the game and test for proper game operation.
2 CREDIT: ON OFF 3 CREDIT: OFF ON 1 CREDIT: ON ON EXSY: GAME Hy
DIFFICULTY HARD:
VERY HARD:
P.P.U TKO BOXING SELECTION
Table 1
PAGE 4 VS. TKO BOXING
The Namco Sub-Board (see Figure 3) is used to expand the memory capacity of the Nintendo MDS pcb. The Sub-Board contains a 4 position dip-switch that configures the pcb for the specific memory chips (Eproms or Ros) used for a particular game. If the switches on the Sub-Board are not set properly, the gase will not operate. Table 2 outlines the various memory devices that can be utilized by the Sub-Board, and the proper switch settings for each configuration. The device numbers in the table are abbreviated. For example, 64 in the table would be a 2764 Eprom or an equivalent memory device.
PROT: SIZ S12 SIZ SIZ Be BS OG PRG 2: «512 256 128 64 256 126 64
su 2 ON ON OFF OFF
CHA: 512 256 128 64
Su4 ON ON OFF OFF -- -- --
TABLE 2
VS. TKO BOXING PAGES
a rT | B. Warranty information. er
Data East USA, Inc., ("Seller"), warrants only to the initial purchaser
("Buyer") of its products that the items listed below are free from defects in material and workmanship under normal use and service for the period specified:
su ARD PCB (AS SUPPLIED IN VS. PAK) 90 DAYS
No other parts of Seller’s products are warranted.
Warranty periods are effective from initial date of shipment from Seller
to Buyer. Seller's sole liability shall be, at its option, to repair or
replace products which are returned to Seller during the warranty periods specified, provided:
- Seller is notified promptly upon discovery by Buyer that stated products are defective.
2, Such products are properly packaged and then returned freight pre-paid, to Seller’s plant.
Thig warranty does not apply to any parts damaged during shipment and/or
due to inproper hand] ing, or due to improper installation or usages or
alteration. n no event shall the Seller be liable for any anticipated profits, loss of profits, loss of use, accidental or consequentia| damages, or any other losses incurred by the customer in connection with the purchase of a Data East USA, Inc., product.
EXCEPT AS SPECIFICALLY PROVIDED IN A WRITTEN CONTRACT BETWEEN SELLER AND PURCHASER, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING Aa cnPLieD WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A’ PARTICULAR
PAGE 6 VS. TKO BOXING
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.