CATHODE RAY TOMES

Battlezone TM-156 1st Printing

Battlezone (rev 2) (Atari, 1980) · Technical Manual · 64 pages · 48 sections · original scan

Page 1
Scan of page 1

This page is a drawing, shown as the original scan.

Page 2

GAME SERIAL NUMBER LOCATION e@

Your game's serial number is stamped on a plate on the outside of the game. The same number is also stamped on the chassis of the TV monitor, Regulator/Audio II PCB, Battlezone Analog Vector-Generator PCB, and Battlezone Auxiliary PCB. Please mention this number whenever calling your distributor for service.

GAME SERIAL # IDENTIFICATION TAG

TV MONITOR

BATTLEZONE oO AUXILIARY PCB

BATTLEZONE ANALOG VECTOR-GENERATOR PCB REGULATORI/AUDIO II PCB

Page 3

Eg “

nance

and Service Manual

Complete with Illustrated Parts Lists

Published by: ATARI INC. 1265 Borregas Avenue P. O. Box 427 Sunnyvale, California 94086

Copyright © 1980 by Atari, Inc. All rights reserved.

No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher.

Lithographedin the USA. 10J © 4 warmer Communications Company

Page 4

Table of Contents

Location Setup A. N@WPartS.. 0... cece nnn cence ence teen een iaes 1 B. Game Inspection . . 3 C. Game Installation. . 3

  • Line Voltage Selection ... 4
  • Interlock and Power On/Off Switches 4 D. Self-Test Procedure . . 7 E. Option Switch Settings . 8
  • Bonus Play Feature. . 8
  • Coin Mechanism Multipliers . . 8
  • Examples of Option Switch Settings . 9 F. GamePlay ...............00.00. . 12
  • AttractMode....
  • Ready-to-Play Mode
  • PlayMode .
  • High Score Initial

Maintenance and Repair A. Cleaning B. Fuse Replacement... C. Opening the Control Panel . 16

  • LED Switch Replacemen . 16
  • Control Handle Maintenance and Repair . 18 TV Monitor Removal ...............55 . 19 D. E. Mirror Removal. . . 20 F. Housing Removal .21
  • Fluorescent Tube Replacement . - 22
  • Speaker Replacement......... - 22 G. Printed-Circuit Board Replacement . . 23
  • Analog Vector-Generator and Auxiliary PCB Removal . . 23
  • Regulator/Audio II PCB Removal .............. . 23 H. Game Operation... 0.0.0... c 0 eee ee eeeee eee 24

Illustrated Parts Lists

Page 5

Figure 1 Figure 2 Figure 3 Figure 4 Figure 5

Figure 6 Figure 7 Figure 8 Figure 9 Figure 10

Figure 11 Figure 12 Figure 13 Figure 14 Figure 15

Figure 16 Figure 17 Figure 18

Figure 19 Figure 20 Figure 21 Figure 22 Figure 23

Figure 24 Figure 25 Figure 26 Figure 27 Figure 28 List of Dlustrations

Overview Of GAME... cee eee eee eee 2 Installation Requirements . . 3 Line Voltage Selection ..... - 4 Interlock and Power On/Off Switches .......... : . 5 Location of Self-Test Switch, Volume Control and Option Switches ..... 6

Self-Test Procedure . 1.0.0... cece cece eee tent e ene nee Game Option Settings . Game Price Settings... . Coin Counter Option Settings Opening the Control Panel

Control Handle Maintenance and Repair........--.. 00. e eee eee 7 TV Monitor Removal . 19 Mirror Removal .. . . . 20 Housing Removal ......... .21 Fluorescent Tube Replacement... 0.0.6.0... cece eect eee eee 22

Printed-Circuit Board Replacement .........-.0. 000s cee e eee eee aes 23 Power Distribution Signal Distribution

Mlustrated Parts Lists: Cabinet-Mounted Assemblies Control Panel Assembly... . Control Handle Assembly Fluorescent Lights .... Housing Assembly

Power Supply Assembly for X-Y Games ......... 0.60 e cece eee eee 36 Batilezone™ Auxiliary PCB Assembly Battlezone Analog Vector-Generator PCB Assembly ~41 Regulator/Audio Il PCB Assembly ............. 46 New Coln Door... . cece secret tere evens cee densuesasten sens 48

Page 6
NOTE

If reading through this manual does not lead to solving a certain maintenance problem, call Tele-Help™ at the Atari Customer Service office in your geographical area, as shown in one of the two maps below. Order all parts from the California office.

WEST and CENTRAL U.S.A.

Parts for all Atari Customers. Sales and Service

Atari Coin-Op Customer Service 1344 Bordeaux Drive, Sunnyvale, CA 94086 Telex 17-1103

(Monday - Friday, 7:30 - 4:00 pm Pacific Time)

From California, Alaska or Hawaii (408) 745-2900 Od

From anywhere else in ihis area toll-free (800) 538-1611

EAST U.S.A.

Sales and Service Only

Atari Inc. New Jersey Customer Service Office Cottontail Lane, Somerset, NJ 08873 Telex 37-9347

(Monday - Friday, 7:30 - 4:00 pm Eastern time)

=z From New Jersey (201) 469-5993

z From anywhere else in this area toll-free (800) 526-3849

Page 7

Notice Regarding Non-Atari Parts

WARNING

Use of non-Atari parts or modifications of your Atari game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

Atari, Inc.’s warranty (printed on the inside back cover of this manual) may be voided, if you do any of the following: 1.) you substitute non-Atari parts in your coin-operated game, or 2.) you modify or alter any circuits in your Atari game by using kits or parts not supplied by Atari.

Not only may the use of any non-Atari parts void your warranty, but any such alteration may also adversely affect the safety of your game, and may cause injury to you and your players.

Page 8

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 9

A. New Parts

The Battlezone™ game has five new parts. If you have worked on Atari games in the past, then you should be aware of these important differences. The new parts are: @ The control handle is a redesign of the Atari gear shifter. It has been strengthened by adding several additional ribs to the interior and exterior of the housing. These ribs keep the assembly properly aligned to assure proper switch contact. Another new feature is the rubber centering bellows; it acts as a centering spring to return the control handle to the center position. The microswitches are now mounted with locknuts for easy replacement.

AAWARNING -SHOCK HAZARD &

This game is designed to be connected only to a grounded 3-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electric shock if this game is not properly grounded!

Page 10

SIDE WINDOW

ATTRACTION

PANEL SPEAKER HOUSING

(1of2)

ACCESS PANEL

CENTER VIEWING WINDOW (FOR PLAYER) TV MONITOR

INSTRUCTION PANEL

CONTROL HANDLE AUXILIARY PCB

START SWITCH

CONTROL PANEL LARGE ey <’) ANALOG VECTOR- GENERATOR PCB

REGULATOR) AUDIO II PCB

POWER ON/OFF SWITCH

POWER SUPPLY

C

mS) FOOTSTEP

Figure 1 Overview of Game

Page 11

e@ Atari's X-Y game circuitry has expanded into two interconnected printed-circuit boards—the Analog Vector-Generator and the Auxiliary PCBs. The circuitry produces more lines on the screen at a faster rate, thus creating a smoother screen image. @ This game includes a newly designed power supply assembly. This power supply has a larger transformer to handle the increased power requirements of the expanded game circuitry. @ Battlezone’s new cabinet design will accept Atari’s new deep-well coin box that holds more coins. The cabinet also includes a removable footstep for the convenience of shorter players. (If you do not wish to mount this footstep on the front of the game, you can store the footstep inside the cabinet.)

These new parts, as well as all other major parts in the game, are illustrated in Figure 1. Throughout this manual, wherever one of these new parts is mentioned, you will see this symbol:

B. Game Inspection

This new game is ready to play upon removal from the shipping carton. However, your careful inspection is needed to supply the final touch of quality control. Please follow these steps to help us insure that your new game was delivered to you in good condition. [co nern NOTE met Do not plug the game in yet!

  • Examine the exterior of the game cabinet for dents, chips, or broken parts.
  • Unlock and open the access panel of the cabinet and inspect the interior of the game as follows: @ Check that all plug-in connectors (on the game harness) are firmly seated. Replug any connectors found unpiugged. Don’t force connectors together. The connectors are keyed so they only go on in the proper orientation. A reversed edge connector will damage a PCB. @ Check that all plug-in integrated circuits on the game PCB are firmly seated in their sockets.
WARNING To avoid possible unpieasani eieciricai shock, do not touch internal parts of the TV monitor with your hands or metal objects held in your hands!

@ Note the location of the game’s serial number—it is printed on the special label on the outside of the game cabinet. Verify that the serial numbers also stamped on the Battlezone Analog Vector-Generator PCB, Auxiliary PCB, Regulator/Audio II PCB and TV Monitor are all identical. A drawing of the serial number locations is on the inside front cover of this manual. Please mention this number whenever you call your distributor for service. @ Check all major subassemblies such as the power supply, control panel and TV monitor for secure mounting. @ Finally, turn on the game and look at the screen through the player's viewing hole. Check that the radar “screen” is centered in the bright orange-banded round hole of the graphics bezel. If it’s misaligned, locate the tape that holds the graphics bezel to the wood mounting. You will find the tape at the rear of the monitor, and the graphics bezel is the upper cardboard. Carefully remove the tape. Then shift the bezel until the TV-monitor image is centered in the hole of the bezel.

Cc. Game

Installation

Figure 2. installation Requirements

Power 175 watts Temperature 0 to 38°C (32 to 100°F) Humidity Not over 95% relative Space Required With footstep: 64x 84/2 cm (25% x 33% in.) Without footstep: 64 x 64 cm (25% x 25% in.) Game Height 190 cm (74% in.)

Page 12

Figure 3 Line Voltage Selection

  • Line Voltage Selection

Before plugging in your game, make sure that the voltage selection plug on the power supply (see Figure 3) is correct for your location’s line voltage. Check the wire color on the plug and see if it is correct per the list below.

Line Voltage Range Voltage Selection Plug Color

90-110 VAC (100) Violet 105-135 VAC (120) Yellow 200-240 VAC (220) Blue 220-260 VAG (240) Brown

  • Interlock and Power On/Off Switches

To minimize the hazard of electrical shock while working on the inside of the game cabinet, two interlock switches have been installed (see Figure 4). One is located behind the access panel and one is behind the coin door. These switches remove all AC line power from the game circuitry when a door is opened.

Check for proper operation of the interlock switches by performing the foliowing steps: @ Unlock and open the access panel and the coin door. @ Plug the AC line power cord into an AC outlet. ®@ = Close the access panel and coin door. @ Set the power on/off switch to the on position. Within 30 seconds the TV monitor should display a picture. @ Slowly open the access panel. The TV monitor picture should disappear when the panel is opened approximately 2.5 cm (1 inch). Close and lock the access panel and repeat this step with the coin door. @ = Ifthe results of the preceding step are satisfactory, the interiock switches are operating properly. If the TV monitor doesn’t go off as described, check to see if the corresponding interlock switch is broken from its mounting or stuck in the “on” position.

Page 13

SAFETY INTERLOCK SWITCH

ON/OFF SWITCH

Figure 4 Interlock and Power On/Off Switches

Page 14

y

BATTLEZONE ANALOG VECTOR-GENERATOR PCB

OPERATOR OPTION SWITCH

VOLUME INCREASE: TURN CLOCKWISE

VOLUME CONTROL

Figure 5 Location of Self-Test Switch, Volume Control

and Option Switches

Page 15

D. Self-Test Procedure

This game will test itself and provide data to demonstrate that the game’s circuitry and con- Part of the self-test procedure includes a display of the operator-selectable game options. Therefore, we suggest you run the self-test procedure anytime you need to change the game’s options. trols are operating properly. The data is provided on the TV monitor and the game speaker; no additional equipment is necessary. To run the self-test, follow the instructions outlined in Figure 6.

Figure 6 Self-Test Procedure

Results if Instruction Test Passes Results if Test Fails

  • Set self-test After about 3 RAM FAILURE is indicated by a sequence of 1 to 10 tones. You will hear a short low ‘switch to on position (see Figure 5). seconds, the TV monitor displays the picture below.

CENTER COIN MECH MULTIPLIER (LEFT MECH OF A 2-MECH DOOR)

RIGHT COIN MECH MULTIPLIER

SWITCH TOGGLE 8& SWITCH TOGGLE 1

SWITCH AT P10 (TOP ONE) (BOTTOM ONE) SWITCH AT M10

DISPLAY OF COMPLETE CHARACTER SET tone for each good RAM chip, and a long high tone for a failing RAM chip. The test stops with the first failing RAM chip. To restart the sequence, press the reset pushbutton on the Battlezone™ Analog Vector-Generator PCB, or set the self-test switch to off, then again to the on position. Identify the bad RAM chip with the table below. Example: four short low tones followed by a long high tone indicates failure of RAM at location B2.

Long High Tone Bad RAM Chip Location ist w2 and H2 3rd Az 4th Al 5th B2 6th B1 7th c2 ath C1 oth D2 40th D1

ROM/PROM FAILURE is indicated by two columns of numbers on the left side of the screen. The number in the left column indicates the failing ROM/PROM(s). Identify the bad ROM/PROM with the table immediately below. The number in the right column indicates the failing data bit of the failing ROM/PROM. Identify the bad bit with the second table below. If more than one bit is failing, the displayed number(s) are hexadecimal combinations of the numbers shown in the second table. Examples:

  • If bits D2 and D3 fail, C is displayed.
  • If bits D2, D3 and D7 faii, 8C is displayed.
  • If bits D4 and D5 fail, 30 is displayed.
  • If bits D1, D3, D5 and D6 fail, 6A is displayed.

Displayed No. Failing ROM Failing PROM BICc3* BIC3*, E3 A3 A3, FIH3- Et FIH1 Jt K1 LM Nt *If ROM or PROM BIC3 is bad, you will hear a continuous low tone, and the program may be unable to display a number. NOMnAwNAo

Page 16

Figure 6 Self-Test Procedure, continued

Results if

Instruction Test Passes

Results if Test Fails

  • Activate slam switch, all control panel switches and coin door switches. As switch activates, you'll hear a low beep. As switch deactivates, you'll hear a high When satisfied with { beep. test, set self-test switch to off position.
  • Sounds Test (Optional) You may test the hardware-generated sounds by starting agame and proceeding as follows: Engine Rumble (Idle): Should be heard as soon as start button is pushed. Engine Rumble (Active): Pushing both control handies forward should cause an increase in pitch. Releasing contro! handles Displayed No. Failing Bit 1 bo 2 D1 4 D2 8 Ds 10 D4 20 DS 40 06 80 D7 MATH BOX FAILURE is indicated by a single letter displayed in the upper right corner of the display. Identify the failure with the table below. Displayed Letter Failure T Time out error H Data error—high byte L Data error—low byte

You will not hear a low or high beep for the defective switch.

should cause engine rumble to return to idle. Loud Shot: Press the fire button. Loud Explosion: Heard when you get hit, indicated by cracked windshield, Soft Explosion: Is heard when you hit an enemy tank or another object.

E. Option Switch Settings

  • Bonus Play Feature Battlezone™ offers a bonus play for certain combinations of coins inserted. This bonus feature is operator-selectable, meaning you may choose to offer it or not.

For example, with your game set at 50¢ per play, players who deposit four successive quarters or a $1.00 coin, then press the start button, can receivea

fast ey Therefore, players can receive 3 plays

for $1.00. This bonus feature encourages players to insert more money than just the minimum 50¢ required for one game. Various other bonuses are also available (see Figure 8).

  • Coin Mechanism Multipliers Since early in 1980, Atari has made available its new coin door which has either two or three mechanisms. All recent Atari game PCBs identify the different mechanisms in a certain pattern.
Page 17

The right coin mechs are all the same to the game’s logic, regardiess of whether you have two or three mechs in your door. in addition, the logic sees the left mech in a 2-mech door and the center mech in a3-mech door as the same. Refer to the diagram below.

[ase isi] [ls] [Is]

ul

This pattern is important for you to know, so you can correctly set the “multipliers” for each mech. The multipliers determine how much each mechanism will be worth to the game’s logic. The basic unit of measurement is 25°, which equals a multiplier of x1. Therefore, if you have a 25¢/25¢/$1 coin door, you witl probably want to set the center and right option-switch multipliers at x 1/ x 4. (The left mech in a 3-mech door always has a value of x 1—you cannot change its value.)

You can set these multipliers with toggles 3 thru5 on the Battlezone PCB switch assembly at location P10. For exact settings of these toggles, refer to Figure 8.

  • Examples of Option Switch

Settings

To explain the options, we have provided in Figure 8 fourteen examples of the most common U.S. situations. The toggles mentioned are all in the switch at location P10; they only relate to game price, coin mechanism multipliers, and bonus play. You should set the toggles relating to other functions as you see fit, although Figure 7 provides “$” symbols indicating Atari’s recommendations.

Figure 7 Game Option Settings To change toggle positions on the switch assemblies, you need not remove the game PCB. The switches, usually colored blue, are easily accessible when the Battlezone Analog Vector-Generator PCB is mounted in place. When changing the options, verity proper results on the TV monitor display by performing the self-test. Note that changing an option on any of the following eight toggles will cause an immediate change on the TV monitor screen during the self-test.

Toggle Settings of &-Toggle Switch on Battlezone PCB (at M10) (BOTTOM switch when PCB is in game) 8 7 6 5 4 3 2 1 Option

On On Off Off

On On On Off

Off Off

On On

On On

Off On

On Off On Game starts with 2 tanks Off Game starts with 3 tanks $ On Game starts with 4 tanks Off Game starts with 5 tanks Missile appears after 5,000 points Missile appears after 10,000 points $ Missile appears after 20,000 points Missile appears after 30,000 points No bonus tank Bonus tank at 15,000 and 100,000 points $ Bonus tank at 25,000 and 100,000 points Bonus tank at 50,000 and 100,000 points English language $ French language German language Spanish language

Page 18

Figure 8 Game Price Settings

The white block below contains the manufacturer's suggested switch at location P10, on the Battlezone™ Analog Vector-Genesettings. All numbers 1 thru 8 are toggle settings on the &-toggle rator PCB (the top switch assembly).

50¢ PER PLAY: Bonus $.50 = 1 play Bonus $.75 = 2 plays No bonus $1.00 = 3 plays $1.00 = 3 plays

:8765;.6.

Straight On Off Off On ”

25¢ Door

4321
OnOnOffOff

25%/$1.00 Door or 25¢/25¢/$1.00 Door

25¢ PER PLAY:

Bonus $.50 = 3 plays

Straight 25¢ Door

25¢/$1.00 Door or 25°/25¢($1.00 Door

Circled numbers refer to coin-door labels you should use with each situation (labels are illustrated on apposite page).

Page 19

Figure 8 Game Price Settings, continued For your information, we have defined below the switch settings for those options relating to game price, coin mechanism multipliers, and bonus play. This information is useful in case you need to temporarily set the Battlezone™ game on free play, or if you have German coin mechanisms in your door.

Toggle Settings of 8-Toggle Switch on Battlezone PCB (at P10). TOP switch when PCB is in game

54324Option
OnOnFree play
OnOff1 coin* for 2 plays
OffOn1 coin™ for 1 play
OffOff2coins* for 1 play$
OnOnRight coin mech x 1$
OnOffRight coin mech x 4
OffOnRight coin mech x 5
OffOffRight coin mech x 6
OnCenter coinmech x 1$(Both these settings affect
OffCenter coin mech x 2the left mech in a 2mech

door)

Toggle Settings of 8-Toggle Switch on Battlezone PCB (at P10). TOP switch when PCB Is in game

876Option
OnOnOnNo bonus coins
OnOnOffFor every 2 coins” inserted, game logic adds 1 more coin*
OnOffOnFor every 4 coins* inserted, game logic adds 1 more coin*
OnOffOffFor every 4 coins* inserted, game logic adds 2 more coins*$
OffOnOnFor every 5 coins” inserted, game logic adds 1 more coin*

“In the U.S., a “coin” is defined as 25°. In Germany a “coin” is 1DM. $ Manufacturer's suggested settings To achieve bonus plays, all coins must be inserted before pushing Start button.

o A, @@ 2 coins =1 play ATARI

ys @ 1 coin = 1 play ATARI

AO @ @ 2 coins = 1 play ATARI

BOE 4 coins=3 plays ne @@ 2 coins = ATR’ -B@@ 3 coins @O@@ 4 coins =

6 @@ 2 coins = 1 play $1 coin=3 plays (Susan B. Anthony coin) ®

@ 1 coin = 1 play arg’ 2 play minimum (2 coins = 2 plays)

Note: Battlezone cannot be set for a 2-coin minimum. Therefore, do not stick the above label no. § on the Battlezone coin door.

ab

Page 20

Figure 9 Coin Counter Option Settings [These toggles determine which coin mechanisms activate which counters]

Toggle Settings of 4-Taggle Switch on Game PCB (at L11) 4 3 2 1 For Games Having These Coin Doors: Option

OnOnThai 1 Bahi/1 Baht, German 1 DM/1 DM, U.S. 25¢/-All 3 coin mechanisms are

25¢, Belgian or French 5 Fr/S Fr, Swiss or French same denomination; all 1 Fr/1 Fr, U.S, 25¢/25¢/25¢, Japanese Y100/Y 100, register on one coin Swedish 1 Kr/1 Kr, U.K. 10 P/10 P, Australian 20¢/- counter. 20°, or lialian 100 L/100 L.

OffOnGerman 2 DM/1 DM, German 1 DM/5 DM, U.S. 25¢-Left and center mechanisms

25¢/$1, or U.S. 25¢/$1. are same denomination; right mech is another denomination. Requires two coin counters.

OnOffNo coin door is currenily designed for this contig-Left mech is one denomina-

uration. tion; center and right mech are another denomination. Requires two coin counters.

OffOffGerman 1 DM/2 DM/5 DM.Left, center and right mechs

are 3 different denominations. Requires three coin ] counters.

F. Game Play

Atari’s Battlezone™ is a one-player game with an XY or vector-generation monitor. The game depicts a first-person view from inside a tank. The battles are fought in a large valley that is completely surrounded by mountains and volcanos. The valley floor contains pyramids and boxes that can provide temporary protection for players. (These cannot be destroyed by shots.)

The enemy consists of slow and fast “super” tanks and intelligent missiles—all of which become more evasive as the game progresses. In addition, flying saucers appear pericdically. These don’t shoot at players, but players can get very high point scores for shooting them.

The Battlezone game has five possible modes of operation: Attract, Ready-to-Play, Play, High Score Initial, and Self-Test. Self-test is a special mode for checking the game switches and computer functions. You may enter this mode at any time. When entered, all game credits are cancelled and the high score initials are reset.

  • Attract Mode The attract mode begins when power is applied to the game, after a play or high score initial mode, or after self-test. This mode is continuous and is only interrupted when a game is paid for and accepted or when in self-test.

In this mode, the TV monitor displays three possible pictures. One is a simulation of a typical game, another is the high score table, and the third picture shows the Battlezone logo rolling up from the bottom of the screen.

  • Ready-to-Play Mode This mode begins when sufficient coins have been accepted for a game. It ends when the start pushbutton is pressed. When this mode begins, the message PUSH START flashes in the center of the
Page 21

screen, and the start button will also flash on and off. The sequence of displayed pictures are otherwise the same as those shown in the attract mode.

  • Play Mode The play mode begins when the start pushbutton is pressed. The start LED will then stay on, and the audio will begin. The mode ends when the player's last tank of the game is lost.

The game starts with the slow tank visible on the screen. The player can determine the position of either type of tank or the missile by reading the messages in the upper left corner of the screen. For example, ENEMY TO RIGHT may be displayed. In addition, the sweeping radar display shows a dot for the enemy's location, accompanied by a sonar “blip” sound.

The upper pie-shaped area on the radar represents the player’s range of view on the screen below. If the enemy falls within this area, it will be shown on the screen below and will be accompanied by the message ENEMY IN RANGE.

Occasionally the flying saucer appears on the screen. It is a harmless observer to the battle and will not destroy the enemy or player. Its position is never shown on the radar, but players can earn 5,000 points for shooting it down. The saucer does act as a distraction, though, since it usually appears at the same time as the enemy tanks or missile. Saucers

ene shot down by the player as well as enemy

tanks. Scoring for hitting the enemy is as follows: the slow tank earns a player 1,000 points; the missile earns 2,000 points; and the super tank earns 3,000 points. A super tank moves and turns twice as fast as both the slow tank and the player’s tank.

Several options allow operators to set the Battlezone™ game for 2 through 5 tanks, for giving a bonus tank after earning various point scores, and for adjusting difficulty by having the missile appear for the first time at various point scores. For information on how to set your game for these options, refer to Figure 7 in this manual.

  • High Score Initial Mode If a player’s score exceeds the minimum on the high score initial list, he or she may put up to three initials on this list at the end of the game. The instructions are self-explanatory and are provided in four languages.
Note that this list is erased whenever you enter the self-test, press the RESET button on the Battiezone™ Analog Vector-Generator PCB, or turn off the power. This resetting will put a list of ten “highest” scores and initials on the screen (to provide player challenge).

Any score on the list over 100,000 points is specially highlighted with a tank symbol following the player’s initials. If a player doesn’t enter his or her initials within about 60 seconds, the game will automatically enter dashes instead. After this, the game reverts to the attract mode.

Page 22

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 23

nance

and Repair

All games require certain maintenance to keep them in good working order. Clean, properly maintained games will attract players and earn more profits.

The most important maintenance item is running the self-test every time you collect money from the cash box. Just looking at a game will not tell you if the control handle switches, fire button, or start switch is broken, or if the LED has burned out. The self-test will inform you of any of these possible problems.

Second, you should regularly clean the outside of the game and the coin mechanisms. In addition, you will need to regularly lubricate the control handle: for details see this chapter.

Page 24

A. Cleaning

The exterior of the game cabinet and the metal and acrylic surfaces may be cleaned with any nonabrasive household cleaner. If desired, special coin machine cleaners that leave no residue can be obtained from your distributor. Do not dry-wipe any of the acrylic panels, because any dust can scratch the surface and result in fogging the plastic.

B. Fuse Replacement

This game contains five fuses—all on the power supply assembly (not including the TV monitor fuses). Note that the F2 holder is unused. Replace fuses only with the same type as listed in Figure 24 of this manual. See the Quadrascan TV monitor manual, TM-151, for the monitor fuse data.

C. Opening the Control Panel

Prior to repairing or replacing any switch on the contro! panel, unplug the game. Then open the coin door,

Reach through the opening and remove ail three sets of carriage bolts, hex nuts, split lock washers, and flat washers, located on the underside of the control panel (see Figure 10). Lift up on the control panel and tilt it towards you.

  • LED Start Switch Replacement The light-emitting diode (LED) switch on the control panel has a very low failure rate. In case the switch should ever be suspect, first test it per the description that follows. To replace the switch, refer to Figure 10.

To remove LED switch: @ Remove all wires from the faulty switch. © Tum the switch counterclockwise (as viewed from inside of control panel) while holding the black cone-shaped nut on the outside of the control panel. ® Install a new switch using the reverse procedure. Reconneci the harness wires.

NORMALLY CLOSED (NC) CONTACT /_-

| \. UGHT-EMITTING-DIODE common / (L-E.D.) CONTACTS CONTACT

Figure 10 Opening the Control Panel

Page 25
NOTE:

Do not remove the flat actuator spring © co)

unless you have a replacement. Removing the spring will bend it, and it will no longer be usable.

LUBRICATE HERE

_ LUBRICATE | HERE FLAT ACTUATOR SPRING

ne ACTUATOR PIN

LUBRICATE HERE

Figure 11. Control Handle Maintenance and Repair

Page 26
  • Remove the wires from the suspected switch.
  • Set multimeter to ohms scale. Set ohms scale to Rx1, then zero the meter.
  • Connect multimeter leads to appropriate LED switch contacts (see Figure 10 for designation of switch contacts and meter lead placement).
  • Check contacts (push and release the switch button) for closed and open continuity.
  • If the contacts do not operate sharply or always remain closed or open, then replace the LED switch as outlined in the figure.

a

  • Control Handle Maintenance and

Repair

Normal maintenance involves lubricating three parts in the control handle approximately every six months (this requires removing the controls). First open the control panel as described in Figure 10. Then unplug the “quick-disconnect” connectors on the four contro! switches, as well as the three connectors for the fire switch.

From the inside of the control panel, remove the four flat and lock washers and four screws that mount the control onto the wood support and the round bezel.

Then open up the contro! handle assembly by removing the six split lock washers and screws (see Figure 11). In addition, remove the two switches and carefully save the small actuator pins.

For lubrication, use only Dow Corning #111 heavy silicone lubricant (Atari part no. 78-1710). Lubricate the following three parts inside the control:

  • The spherical part of the shaft and the two small pivot pins that protrude from this area
  • The two clear plastic actuator pins, located over the switches (push the narrow ends of the pins into the tube to cover them with lubricant)
  • The top surface only of the flat actuator spring. Note: do not remove this spring unless you have a replacement on hand! Removing the spring will bend it, and it will no longer be usable.

Reassemble the control handle, and then reinstall it in the control panel. Reconnect the harness wires as shown in the following diagram: make sure the right colors go to each switch.

BLACK GREEN | YELLOW instal YELLOW

YELLOW GREEN WHITE

Repairs on the control handle would probably only involve replacement of switches. When removing a switch, be careful not to lose the small clear plastic actuator pins that sit above the white switch actuators. Note: the flat head of the pin must always face towards the switch actuator.

Page 27

D. TV Monitor Removal

WARNING High voltages may exist in any television monitor, even with power disconnected. Use extreme caution and do not touch electrical parts of the TV yoke area with your hands or with metal objects in your hands! If you drop the TV monitor and it breaks, it will implode! Shattered glass and the yoke can fly 6 feet or more from the implosion. Use care when replacing any TV monitor.

If you should need to remove the Quadrascan X-Y TV monitor, follow steps 1 thru 6 as listed on this page. Refer to Figure 12.

  • Unplug the harness connector underneath the TV monitor. Be sure the game is unplugged from its wall outlet!
  • Remove the two sets of carriage bolts, flat and split lock washers, and hex nuts that hold down the TV chassis. (This hardware is located at the left and right side of the monitor, near the access panel opening.) Carefully slide the TV monitor chassis out the rear of the game. If you must replace the TV monitor, place the red and green overlays on the face of the new picture tube as follows. Place the red overlay within the top 4 inches of the screen; then butt up the green overlay to the red one. (These overlays may overlap by a maximum of 1/8 inch.) Once the monitor has been installed in the cabinet, check for proper alignment with the graphics bezel as follows. The horizon line (the floor of the valley) should be even with the short horizontal line in the graphics bezel. This line is located between the two screws in the bezel design. Also, the vertical center line of the gunsight should be directly under the D in RADAR (at the top center of the bezel).

Disassemble in the order indicated. (Circled numbers match the steps above.)

Figure 12 TV Monitor Removal

Page 28

‘a 7A

Figure 13 Mirror Removal

E. Mirror Removal

If you wish to remove the half-silvered mirror for cleaning or replacement, follow these instructions. Handle the glass mirror with care—it is heavy! Never wipe the silvered side with an abrasive cloth: you will scratch the coating. Unlock and remove the rear access panel. Unplug the harness connector located at the left side of the cabinet opening.

Remove the two Phillips screws that secure the wood support (located at the mirror’s rear edge): see Figure 13. Carefully slide the wood support and the mirror out of the cabinet. Note that the wood is NOT attached to the mirror!

Page 29

F. Housing Removal

If you wish to replace the fluorescent tube, either speaker or any of the acrylic panels, you will need to remove the front housing from the game. Follow the illustration in Figure 14. Remove the three Allen-head screws and split iock washers at the top of the game, as well the three at the bottom of the housing. They secure the housing to the cabinet.

Tilt the top of the housing towards you,-then unplug the harness connector for the speakers. Remove the housing and lay it on a clean surface,

Figure 14 Housing Removal and Speaker Replacement

Page 30

Baitlezone™

with its inside facing up. You can now service any parts in the housing, as well as replace either fluorescent tube. You'll find a list of housing replacement parts in Figure 23.

  • Fluorescent Tube Replacement
CAUTION If you drop a fluorescent tube and it breaks, it will implode! Shattered glass can fly 6 feet or more from the implosion.

he care when replacing any fluorescent

ube.

To replace the white fluorescent or blacklight tube behind the front graphics attraction panel, follow this procedure (see Figure 15):

  • Remove the housing as described previously. Unplug the harness connectors for both fluorescent tubes. If you have to replace the blacklight tube, then also remove the two screws that

Figure 15 secure the light board to the cabinet, and slide out the whole assembly.

  • Remove the two Y-shaped connectors from the ends of the fluorescent tube. Now carefully remove the tube from its clamps by pulling it towards you.
  • Replace with a new tube. Do not snap the tube in vigorously—you may break it, causing an implosion!
  • Reconnect the Y-shaped connectors. Reinstall the fluorescent light assembly with the two screws (if you removed it). Reconnect the harness connectors, and replace the housing on the front of the game.
  • Speaker Replacement First disconnect the harness plugs for the defective speaker. Then remove the four screws that hold the speaker in the wood mounting block (the wood block and speaker grille remain attached to the housing with rivets). Replace the speaker, then reconnect the harness connectors.

Fluorescent Tube Replacement

Page 31

REGULATORY AUDIO II PCB BATTLEZONE AUXILIARY PCB

“~» BATTLEZONE ANALOG VECTOR: GENERATOR PCB

Figure 16 Printed-Circuit Board Replacement

G. Printed-Circuit Board Replace

Board Replacement

You may wish to remove the Battlezone™ Analog Vector-Generator printed-circuit board (PCB), Auxiliary PCB, or the Regulator/Audio I! PCB for service. or inspection. To do this, refer to Figure 16 and pro-

ae ceed as follows:

1. Analog Vector-Generator and

Auxiliary PCB Removal

Unlock and open the access panel. Unplug the 24-pin PCB interconnector from the Auxiliary PCB or the Analog Vector-Generator PCB (whichever board you are removing). Remove the 44-pin edge connector from the tight side of the PCB. Locate the Phillips-head screw that extends through the PCB and into the wood block (at the right side of the board). Remove this screw. Remove the PCB from the cabinet by pulling it out of the plastic PCB retainer. Reinstall the PCB, making sure that the 44-pin edge connector is properly plugged in. Note that the connector is keyed to fit on only one way, So if it doesn’t slip on easily, don’t force it! A reversed connector will probably damage your game and will void the warranty. Check that the operation of the game is correct by performing the self-test. This is especially

important with any game when you replace a PCB.

Regulator/Audio Il PCB Removal Unlock and open the access panel. Remove the five plug-in connectors. Note that all of these connectors are also keyed for proper orientation. Locate the four Phillips-head screws that extend through the PCB and into the wood behind the PCB. Remove and save these four screws and the fiber washers behind the board. Remove the PCB from the interior wall of the cabinet.

Page 32

Battiezone™

H. Game Operation

With this manual you received three large sheets that contain the wiring and schematic diagrams for your game. Sheet 1, Side A, includes information that shows the arrangemeni of these diagrams. The diagrams include information that explains the functions of the circuits and defines inputs and outputs.

Battlezone™ is a microprocessor-controlied game. The microprocessor is contained on the Analog Vector-Generator PCB. This board receives switch inputs from the control panel and coin door. These inputs are then processed by the Analog Vector-Generator PCB and output to the TV monitor, Regulator/Audio {| PCB, and contro! panel.

The TV monitor is an X-Y monitor. Therefore, the monitor receives signals for the X, Y and Z axes. Since the location of the beam in the monitor is totally controlled by the X- and Y-axis outputs of the Analog Vector-Generator PCB, this board does not contain a standard sync circuit. The X- and Y-axis inputs to the monitor step in increments of 1024 steps for the X (horizontal) axis, and 768 steps for the Y (vertical) axis. The Z axis merely controls the intensity of the beam. The Regulator/Audio I! PCB performs two functions: 1) it regulates the voltages from the power supply to +5 VDC, +12 VDC, and + 22 VDC, and 2) it amplifies the audio output from the Auxiliary PCB.

Specifically, the +5 VDC from the Regulator/Audio Il PCB provides most logic power to the Analog Vector-Generator and Auxiliary PCB; + 12 VDC provides power for the analog output of the Analog Vector-Generator PCB; and +22 VDC provides power for the audio output of the Auxiliary PCB. The audio output from the Regulator/Audio II PCB directly drives the game speakers and is controlled by the volume control, mounted inside the coin door.

The Power Supply is the source of all voltages in the game. These voltages are protected by four fuses in the fuse block on the power supply chassis. The primary winding of the power supply transformer is protected by the cartridge-type fuse in the power supply chassis.

Figure 17 illustrates the distribution of power in this game. Figure 18 illustrates the distribution of signals.

os

Page 33

CONTROL PANEL

COIN DOOR

INTERLOCK SWITCHES:

REGULATOR/AUDIO II PCB i a

FLUORESCENT & BLACK LIGHTS

TV MONITOR

AUXILIARY PCB 4 >

ANALOG VECTOR- GENERATOR PCB

ON/OFF SWITCH

/__6.1vAC

LINE VOLTAGE

POWER CORD

< POWER SUPPLY

Figure 17 Power Distribution

Page 34

SPEAKERS

SPEAKER

SPEAKER1&2 CONTROL PANEL

VOLUME CONTROL

AUXILIARY PCB

COIN DOOR

ANALOG VECTOR- Peso) GENERATOR PCB

REGULATORIAUDIO II PCB.

Figure 18 Signal Distribution

Page 35

Illustrated Parts Lists

The purpose of this chapter is to provide you with the necessary information for ordering replacement parts for your Battlezone™ game. Please note that, for simplicity, common hardware has been deleted from most of these paris lists. This includes screws, nuts, washers, bolts, etc.

The parts lists have been arranged in alphanumeric order. For example, all “A-” prefix numbers come first. Following this are numbers in sequence evaluated up to the hyphen, namely 00- thru 99-, then 000598- thru approximately 110000-.

When ordering parts from your distibutor, give the part number, part name, applicable figure number of this manual, and serial number of your game. This will help to avoid confusion and mistakes in your order. We hope the results will be less downtime and more profit from your game.

Page 36

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL! Reproduction. forbidden without the Specitic written. permission of tat, inc. Sunnyvale, Gaiifornia” This drawing is only conditionally issued. and either ceceipt nor possession thereo! conver or vansfars any fightin, or license to use, the subject matter of the Housing Assy.— rain or any sigh or teémical information stown 036263-01 treo, fran gto epaaice ne tiga eat

036263-02036143-01Fluorescent Lights—ore sub él rater thea uneas by wit ageument
(Green Overlay)(Micron)‘See Figure 22Sin‘ wien permission Hom fhe corporation

oe=a 035829-04 (Graphics Bezel)

036124-01 (Black Bezel) A036150-01 Auxiliary PCB— (Monitor Assy.) See Figure 25 036116-01 (Retainer Strip) A036245-01 Control Handle Assy.— (Lt. & Spkr, Harness) See Figure 21

Control Panet Assy.—i.al
See Figure 20Pe.148001-001:

= | (Oval Speaker) (Lock)

19-9032B&D&%

(Vol. Control) 00788202 —— ¢ (Interl. Sw. Cover) > | 036130-01 (Speaker Grille) 03626201 (Coin Box Bracket) 035745.03 A036247-01 (10* PCB Retainer) (PCB Interconnector) A036189-01

(Interl. Sw. Assy.)0361.24.02:034536-02

(Coin Deflector). SS __ (Vibration Damper) WL 7F™ A021700-01, -02, -03 : New Coin Door— (Coin Box) See Figure 28 | 030249-01 (Separator) 78-6H002 Analog Vect.-Gener. PCB— 035745.02 (Rubber Matting) See Figure 28 (184PCB Retainer) Reg./Audio I! PCB— = See Figure 27 x

009992-01 (On/Off Sw. Cover)

en 036280. a BQ (Footstep Assy.) Power Supply Assy.— ‘See Figure 24 (On/Oft Sw. Assy.)

A036244.01 (Main Harness)

Schematics, Self-Test Label & Manuals— see parts list on opposite page 78-3201 (Cabinet Leg) AQanaan eo (Power Cord)

Figure 19 Cabinet-Mounted Assemblies A036140-xx B

Page 37

Figure 19 Cabinet-Mounted Assemblies Parts List

Part No. Description

A002465-01 Coin Counter A021700-01 Coin Box Assembly (for all the same coins) A021700-02 Coin Box Assembly (for two different coin denominations—has one separator) A021700-03 Coin Box Assembly (for three different coin denominations—has two separators)

A034841-03Strain Relief Power Cord(domestic)
A034863-03Strain Relief Power Cord(German)

A034631-01 On/Off Switch Assembly A036150-01 Monitor Assembly

A036189-01Interlock Switch Assembly(modified for safety)
A036244-01Main Harness Assembly(a/so includes on/off switch, 2 interlock switches and their brackets,

and volume control and its bracket) A036245-01 Fluorescent Light and Speaker Harness Assembly A036247-01 Printed-Circuit-Board Interconnector A036260-01 Footstep Assembly (includes rubber matting) The following six items are the technical information supplements to this manual:

DP-156-01Battlezone™ Schematic Drawings(Sheet 1)
DP-156-02Battlezone Schematic Drawings(Sheet 2)
DP-156-03Battlezone Schematic Drawings(Sheet 3)

ST-156 Label with Self-Test Procedure and Option Switch Settings ™-151 Instruction and Service Manual for G05-802/805 Quadrascan™ X-Y Monitor TM-156 Battlezone Operation, Maintenance and Service Manual 19-9032 Volume Control

71-2110Panel Cartridge Lock Mechanism(for access panel)

7507017 Spacer for Mounting Printed Circuit Boards 78-3201 Cabinet-Leveling Leg 78-6H002 1/8-Inch Thick Corrugated Rubber Matting for Footstep (74% x 23 5/8 inches are required)

78-240125-Inch Beaded Nylon Tie Wrap(for PCB Edge Connectors)

007882-02 Interlock Switch Cover 009992-01 On/Off Switch Cover 030249-01 Coin Box Separator 033266-01 Monitor Mounting “L” Bracket 034536-02 Foam Vibration Damper for Printed-Circuit Boards 035829-01 Graphics Bezel 036116-01 Housing Retainer Strip 036124-01 Black Cardboard Monitor Bezel 036124-02 Cardboard Coin Deflector 036130-01 Speaker Grille 036143-01 Mirror 036262-01 Coin Box Bracket 036263-01 Red Monitor Overlay 036263-02 Green Monitor Overlay 148001-001 6x9-Inch 4-Ohm 15-Watt Oval High-Fidelity Speaker 035745-02 18-Inch Plastic PCB Retainer 035745-03 10-Inch Plastic PCB Retainer

Page 38

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 39

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Ino. Sunnyvale, GA, This drawing is only conditionally issued, and neither receipt nor possession thereot confers or transfers any ight in, or license to use, the subject matter of the drawing or any design of technical Information shown thereon, nor any Control Handle Assy.— right to reproduce this drawing or any part thereof. @ See Figure 21 Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's writ: ten license, no right to reproduce this drawing Is (<>) Granted or ‘the subject matter thereot ‘written agreement with or written permis the corporation,

P . 78-6900402 005255-04:

Figure 20 Control Panel Assembly A036139-01 A

Parts List

Part No. Description

A036246-01 Control-Panel Harness Assembly 62-039 SPDT Momentary-Contact Pushbutton Start Switch with Red Light-Emitting Diode 75-07054 Flat Nylon Washer, 0.470" inside diameter x 0.968” outside diameter x 0.075” thick 75-9910W0 #15/32-32 Steel Stamped Nut 78-6900402 Vinyl Foam Single-Coated-Adhesive Tape, 1/8” thick x %4” wide 005255-04 Control-Handle Bezel 033127-01 Black Molded Switch Bushing 035830-01 Control Panel with Graphics 036102-01 Wood Support Block for Control Handles

Page 40

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor possession thereot confers or transfers any right in, of license to use, the subject matter of the drawing or any design of technical information shown thereon, nor any Tight to reproduce this drawing or any part thereof. Except for manufacture by vendors of Atari, inc., and for manufacture under the corporation’s writ: ten license, no right to reproduce this drawing is Granted or the subject matter thereof unless by written agreement with or written permission from the corporation.

A035840-01 assembly has NO fire switch and harness (left control handle) A035940-02 assembly HAS the fire switch and harness (right control handle)

65-021A

7214128 ad 72-8614

~ ~

85-22F608

Figure 21 Control Handle Assembly A035940-01 and -02 B

Page 41

Figure 21. Control Handle Assembly Parts List

Part No. Description

A036277-01 Shaft Assembly with Fire Switch Harness A036278-01 Shaft Assembly without Fire Switch Harness A036281-01 Centering Bellows 62-043 SPST Pushbuiton Switch with Red Non-Lighting Cap (used as fire switch) 65-021A Single-Pole Single-Throw Low-Force Miniature Switch 7214128 #4-40 x 34” Pan-Head Cross-Recessed Steel Cadmium-Plated Machine Screw 72-8614 #6-32 x 7/8" Hex Socket-Head Steel Machine Screw 75-046 #6 Internal-Tooth Steel Split Lock Washer 75-944S #4-40 Steel Self-Locking Polymer Hex Nut 78-1710 Dow Corning Heavy Silicone Compound #111 Lubricant 78-3002003 Spring 85-22F608 #6-32 x ¥2" Pan-Head Phillips Self-Threading Type F Steel Machine Screw 000609-02 Control Handie Housing (two of these required per contro! handle assembly) 005255-04 Control-Handle Bezel 035792-01 Straight-Pattern Detent 035844-01 Clear Plastic Actuator Pin 035995-01 Plastic Control Handle (Right Half) 035995-02 Plastic Control Handie (Left Haif) 035997-01 Plug for Control Handle 036276-01 Bezel for Fire Pushbutton 036282-01 Flat Actuator Spring 178010-001 Nylon Actuator Ball

Note: The control-handle bezel is not part of this control handle assembly. It is listed here for your convenience.
Page 42

Wire Nuts Not ‘Shown for Clarity NOTICE TO ALL PERSONS RECEIVING THIS GONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally. issued, and neither receipt nor possession thereot confers or transfers any right in, or license to use, {he subject matter of the drawing or any design of technical information shown thereon, mor any Fight to reproduce this drawing or any part thereo' Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's writ: ten license, no right to reproduce this drawing Is granted or the subject matter thereof unless by written agreement with or written permission from the corporation.

Figure 22 Fluorescent Lights A036146-01

Parts List A

Part No. Description

‘A005493-01 Fluorescent Light Harness 70-304 18-Inch 15-Watt Cool White Fluorescent Tube 70-306 18-Inch 15-Watt Blacklight Fluorescent Tube 79-561816P Wire Nut for 16- to 18-Guage Wires 99-11003 Fluorescent Lamp Starter

99-11008 Ballast Transformer 99-11009 Starter Socket 99-11011 1%2-Inch Clamp (for white tube) 99-11012 1-Inch Clamp (for blacklight tube) 035835-01 Y-Lead Connector

Page 43

Batilezone™

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., ‘Sunnyale, CA. This drawing is only conditionally issued, and neither receipt nor possession thereof confers ot transfers any right in, or license to use, the subject matter of the drawing or any design of 48-004 technical information shown thereon, nor an right to reproduce this drawing or any part thereof. Except for manufacture by vendors of Atari, Inc., gan for manufacture unde the corpration’s wit ten license, no right to reproduce this drawing is Granted or the subiect matter thereof Unless by A036248-01 Written agreement with or written permission from the corporation.

036258-01 ™,

036256-01

036826-01

Figure 23 Housing Assembly A036147-01 B

Parts List

Part No. Description

A036248-01 Speaker Harness Assembly 48-004. 5-Inch 8-Ohm 5-Watt High-Fidelity Speaker 000869-01 Speaker Grille 036152-01 Side Window 036256-01 Center Viewing Window 036258-01 Housing 036827-01 Attraction Panel with Graphics 036828-01 Instructions Decal

Page 44

TOP VIEW 034482.02

78-70501SC NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the Specific written permission of Atari, Inc., Sunnyvale, CA. This drawing Is only conditionally issued, and neither receipt nor possession thereof confers or transfers any right in, or license to use, the subject matter of the draw: Ing or any design or technical information shown thereon, nor any right to reproduce this drawing of any part thereof. Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's written cense, no right to reproduce this drawing is granted or the Subject matter thereof unless by written agreement with of written permission from the corporation.

BOTTOM VIEW

3A-MDA3501

A034629-01 79-15021001

A Figure 24 Power Supply Assembly for X-Y Games A035892-01

Page 45

Figure 24 Power Supply Assembly for X-Y Games Parts List

Part No. Description (Reference Designations in Bold)

A034629-01 A.C. Harness Assembly A034630-01 RFI Filter Assembly (FL1) A035674-01 Voltage Plug Assembly (set of four plugs) A035888-01 or -02 Transformer Assembly (T1) A035890-01 Power Harness Assembly A035891-01 Fuse Harness Assembly 29-053 26,000 uf 15 V Electrolytic Capacitor (C1) 3A-MDA3501 Bridge Rectifier, Tyoe MDA 3501 (CR1) 46-2014001 4-Amp. 125 V 3AG Slow-Blow Glass Cartridge-Type Fuse (F4, F5, F6) 46-2017002 7-Amp. 250 V 3AG Slow-Blow Glass Cartridge-Type Fuse (F1) 46-301203 20-Amp. 32 V 3AG Slow-Blow Glass Cartridge-Type Fuse (F3) 78-2708 Nylon Type 6/6 Hole Bushing with 5/8-Inch Inside Diameter x 55/64-Inch Outside Diameter x Ya-Inch Thick 78-70501SC 2-Inch Diameter Capacitor Mounting Bracket 79-15021001 2-Circuit Single-Row Terminal Block 79-3206 5-Position 3AG Fuse Block with ¥%-Inch Quick-Disconnect Terminals 79-4411006 Panel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post 034482-02 Power Supply Chassis 034544-01 Fuse Block Cover 036304-01 Label for Fuse Values

Page 46

NOTICE TO ALL PERSONS RECEIVING THIS ORAWING CONFIDENTIAL! Reproduction forbidden without tne Specific watten pormission of Ataf. Inc... Sunnyvale, California’ This drawing Ts only conditionally issued, and no! possession thereo! confers or rancters 3 Ticense to use, the subject matter of the ig oF any design or technical information. shown thereon, nor any rigntto reproduce this drawing or any part thoreot except tor manufacture by vendors ot A and for manutacture under the corporation's writ. no right to reproduce this drawing is granted thoreo! uniess by wilten agreement ission trom the corporation,

a

uae

[o3ei76%

GEISEEZ

o3e160%

TAL sie ria eb

TAL

7418374

ras

gz OH hh.

osei78e Aww iS

a <n nag OGEEoss erred

# é

i IS A

sis!

“\F| Gee} ae Ea 37004 r ¢ ¢ 2953 ' [_srooe oe &

SPAREpace,Pace,

wad

2Focn3
64hoeEt
137004se QofaseGeyGR)”

rs i 8 cr D> 74508, [rasBet T Tied BB haw I 137004 HH

paisoRTasorasoeyGA

S88805

TabaTasErie)

ox ORG '

ware ¢EZIXSSPARES,

R40 o i ce ty coed 2 |

onSPARES‘SPARE|

m7 | BaocsscsaqpCENOCGTEE]' «ON ie a [o} Ss |

Figure 25 Battlezone Auxiliary PCB Assembly A035678-01 A

Page 47

Figure 25 Battlezone Auxiliary PCB Assembly Parts List

Part No. Description (Reference Designations and Locations in Bold)

C012294-01 Audio VO N-Channel MOS/LSI Custom Chip (B/C2) 19-315254 250K Ohm Vertical PCB-Mounting Cermet Trimpot (R11) 21-101153 015 uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor 21-101472 .0047 uf, +10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (C21, 22) 21-101474 .47 uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor

24-25010610 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor(C13, 14)

24-250107 100 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C27)

24-25047547 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor(C9)

(24-250477 470 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C28) 29-088 -1 uf Ceramic-Disc Radial-Lead 25V Capacitor (C1-8, 10, 12, 15-20, 23, 24, 26, 30-35) 31-1N914 75V Type-1N914 Switching Diode (CR1)

37-LM324Type LM324 Integrated Circuit(K5, M5)

37-4066 Type 4066 Analog Switch Integrated Circuit (J3, L4)

37555Type 555 Timer Integrated Circuit(F3)
37-74LS00Type 74LS00 Integrated Circuit(D3)
37-74LS02Type 74LS02 Integrated Circuit(D4)

37-74LS04 Type 74LS04 Integrated Circuit (E4) 37-74LS20 Type 74L820 Integrated Circuit (J4)

37-74LS32Type 74LS32 Integrated Circuit(C4)
37-74LS74Type 74LS74 Integrated Circuit(C5, J5)

37-74S86 Type 74S86 integrated Circuit (E5) 37-74LS139 Type 74LS139 Integrated Circuit (C3) 37-74LS161 Type 74LS161 Integrated Circuit (D1, E1, F4, F5)

37-74LS164Type 74LS164 Integrated Circuit(H4, H5)
37-74LS273Type 74LS273 Integrated Circuit(M2)

37-74LS374 Type 74LS374 Integrated Circuit (C1)

37-74S08Type 74S08 integrated Circuit(D5)
37-74109Type 74109 Integrated Circuit(B4)

38-MV5053, Type MV5053 Red Light-Emitting Diode (CR2)

79-42C1616-Contact Medium-insertion-Force Integrated Circuit Socket(B1, F1, H1, J1, K1, L1, M1)
79-42C4040-Contact Medium-Insertion-Force Integrated Circuit Socket(B/C2, D/E2, F2, HiJ2, K2)

020670-01 Test Point

036174-01Programmable Read-Only Memory(B1)
036175-01Programmable Read-Only Memory(M1)
036176-01Programmable Read-Only Memory(L1)

036177-01 Programmable Read-Only Memory (K1)

036178-01Programmable Read-Only Memory(J1)
036179-01Programmable Read-Only Memory(H1)
036180-01Programmable Read-Only Memory(F1)
110000-1021K Ohm, + 5%, %W Resistor(R2, 3, 5, 7, 15, 16, 22, 38, 46-52)
Page 48

a Figure 25 Battlezone™ Auxiliary PCB Assembly, continued Parts List

Part No. Description (Reference Designations and Locations in Bold)

110000-10310K Ohm, + 5%, %4W Resistor(R13, 18, 30, 36)

110000-104 100K Ohm, + 5%, %4W Resistor (R8, 10, 23-25, 28, 31) 110000-151 150 Ohm, + 5%, %4W Resistor (R37, 45) 110000-223 22K Ohm, + 5%, ¥4W Resistor (R9, 14, 17, 29)

110000-33333K Ohm, + 5%, %4W Resistor(R12, 19-21, 26, 34, 35)

110000-334 330K Ohm, + 5%, %4W Resistor (R27, 32, 33)

110000-471470 Ohm, + 5%, %4W Resistor(R1, 39-44)

110000-472 4.7K Ohm, + 5%, %4W Resistor (R6)

137003-001Type 74S03 Integrated Circuit(E3)

137004-001 Transistor Array (D/E2, F2, H/J2, K2) 179010-001 12-Pin PCB Header

Page 49

Figure 26 Battlezone™ Analog Vector-Generator PCB Assembly A036424-01 and -02 A Bit BH Be 0 noel te ea Wives 00sec.) REY athe OE gH cool Pi sea

ee ee

Page 50

Figure 26 Battlezone™ Analog Vector-Generator PCB Assembly Parts List

Memory Components and Their Equivalents (Locations Shown in Bold)

-01 P.C. Boards 02 P.C. Boards (PROMs) (ROMs)

036409-01 (N1) 036409-01 (N1)

036410-01 (L/M1) 03641001 (LIM1)

036411-01 (K1) 036411-01 (K1)

03641201 (J1) 03641201 (1)

036413-01 (F/H1) 036413-01 (FIH1)

036414-02 (Et) 036414.02 (E1)

036415-01 (A3) 036421-01 (A) 036418-01 (3)

036416-01 (BIC3) 03642201 (BIC3) 036419-01 (FIH3)

Page 51

Figure 26 Battlezone™ Analog Vector-Generator PCB Assembly, continued Parts List

Note: The Battlezone™ Analog Vector-Generator PCB consists of the Battlezone memory chips (described on the previous page -») in the Memory Equivalents Table) PLUS the Universal Vector- Generator PCB. The latter is interchangeable with Battlezone and future X-Y games, but not with Lunar Lander™ or Asteroids™, All the following parts in this figure make up the Universal Vector-Generator PCB Assembly.

Part No. Description (Reference Designations and Locations in Bold)

Universal Vector-Generator PCB Assy., A035742-01 and -02, Rev. B, consists of the following parts: 49-007 10K Ohm, + 20%, 1/%4W 8-Pin Dual-Inline-Package Resistor Network (RP1, RP2—use only if board has 74LS170s or 74LS670s at locations E6, F6, H6} 19-315103 10K Ohm Vertical PCB-Mounting Cermet Trimpot (R88, 98) 19-315201 200 Ohm Vertical PCB-Mounting Cermet Trimpot (R73, 74) 21-101102 .001 uf, +10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (C69, 70, 93, 94) 21-101473 .047 uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (C56, 59) 24-250106 10 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C17, 18) 24-250107 100 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C78, 83-86) 24-500105 1 uf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor (C30, 89, 90) 28-101100 10 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C44) 28-101101 100 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C27) 28-101151 150 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C63) 28-101221 220 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C82) 28-101390 39 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C25, 64) 29-006 1 uf, + 10%, 35V Tantalum Capacitor (C88) 29-088 -1 uf Geramic-Disc 25V Radial-Lead Capacitor (C1-16, 19-23, 26, 28, 29, 31-39, 45, 46, 50-54, 61, 72-77, 79-81, 97,98. Also, for -01 PCB Assy. only: C40, 41, 48, 49. For -02 PCB Assy. only: C42, 43, 50, 51)

31-1N100100V Type-1N100 Switching Diode(CR11)
31-1N91475V Type-1N914 Switching Diode(CR1, 3-10)

33-2N3906 Type-2N3906 PNP Switching and Amplifying Transistor (Q3, 7) 34-2N3904 Type-2N3904 NPN 60V 1-Watt Transistor (Q1, 2, 8, 9) 34-2N6044 Type-2N6044 Darlington NPN Transistor (Q4-6)

37-LM319Type LM319 Integrated Circuit(B12, D12)

37-TLO82CP Type TLO82 Integrated Circuit (A10, D10)

37-13201Type LF13201 Integrated Circuit(B10, D11, E10)
37-347Type TLO84 Integrated Circuit(C11)
37-74LS00Type 74LS00 Integrated Circuit(J4)
37-74LS02Type 74LS02 Integrated Circuit(N9, M7)
37-74LS08Type 74LS08 Integrated Circuit(L5, P8)
37-74LS10Type 74LS10 Integrated Circuit(K4)
37-74LS14Type 74LS14 Integrated Circuit(B6)
37-74LS20Type 74LS20 Integrated Circuit(M5)
37-74LS27Type 74LS27 Integrated Circuit(N7)
Page 52

Parts List a Figure 26 Battlezone™ Analog Vector-Generator PCB Assembly, continued

Part No. Description (Reference Designations and Locations in Bold)

Universal Vector-Generator PCB Assy., A035742-01 and -02, Rev. B, consists of the following parts:

37-74LS32Type 74LS32 Integrated Circuit(J5, K10, L2, M8)
37-74LS42Type 74LS42 Integrated Circuit(B4, J7)
37-74LS74Type 74LS74 Integrated Circuit(H10, L9, L10, M9)
37-74LS86Type 74LS86 Integrated Circuit(D7)
37-74LS109Type 74LS109 Integrated Circuit(N8)
37-74LS139Type 74LS139 Integrated Circuit(C4, K5, M2)
37-74LS157Type 74LS157 Integrateduit(D4, E4, F4, H4)
37-74LS161Type 74LS161 Integrated Circuit(K6, L4, L6, M6, N6)
37-74LS164Type 74LS164 Integrated Circuit(P9)
37-74LS174Type 74LS174 Integrated Circuit(C7, L7, M11)
37-74LS175Type 74LS175 Integrated Circuit(F8, F9, J8, K8)
37-74LS191Type 74LS191 Integrated Circuit(F10, J6)
37-74LS193Type 74LS193 Integrated Circuit(E5, F5, H5)
37-74LS194Type 74LS194 Integrated Circuit(A5, A6, B5, C5, D5, D6)

37-74LS244 Type 74LS244 Integrated Circuit (K3, N2, N11, P11, R11)

37-74LS245Type 74LS245 Integrated Circuit(F2,P2,P4) Acceptable substitute is part no. 37-8304B.
37-74LS273Type 74LS273 Integrated Circuit(C8)
37-74LS367Type 74LS367 Integrated Circuit(F7, H7)
37-74LS393Type 74LS393 Integrated Circuit(M4, N5)
37-74LS399Type 74LS399 Integrated Circuit(H8)
37-74LS670Type 74LS670 Integrated Circuit(E6, F6, H6) Acceptable substitute is part no. 37-74LS170.
37-74S00Type 74S00 Integrated Circuit(C6)
37-74802Type 74S02 Integrated Circuit(K9)
37-74804Type 74804 Integrated Circuit(K2, R9)
37-74S74Type 74S74 Integrated Circuit(J10)
37-74S260Type 748260 Integrated Circuit(L8)
37-7404Type 7404 Integrated Circuit(H11)
37-74193Type 74193 Integrated Circuit(N4)

37-7805 +5V Voltage Regulator (VR2) 37-7815 +15V Voltage Regulator (VR3) 37-7915 —15V Voltage Regulator (VR1) 38-MV5053 Type MV5053 Light-Emitting Diode (CR2)

41-3003100 uH, + 10%, Hot-Molded Plastic Fixed R.F. Choke(L1)

62-001 SPST Momentary Pushbutton Switch (SW1)

66-114P1T4-Station Single-Throw, Dual-Inline-Package Bit Switch(L11)
66-118P1T8-Station Single-Throw, Dual-Inline-Package Bit Switch(M10, P10)

79-42C24 24-Contact Medium-Insertion-Force Integrated Circuit Socket (A3, B/C3, D3, E1, E3, F/H1, F/H3, J1, J3, K1, L/M1, N1) 79-42C40 40-Contact Medium-Insertion-Force Integrated Circult Socket (L/M/N3) 81-4302 Nylon Snap-In Fastener

90-10212.096 MHz, +.005%, Crystal(¥2)

90-6013 Microprocessor (L/M/N3) 90-7033 Random-Access Memory (A1, A2, B1, B2, C1, C2, D1, D2, H2, J2) 020670-01 Tesi Point

036408-01Programmable Read-Only Memory(K7)
Page 53

Figure 26 Battlezone™ Analog Vector-Generator PCB Assembly, continued Parts List AS Part No. Description (Reference Designations and Locations in Bold)

Universal Vector-Generator PCB Assy., A035742-01 and -02, Rev. B, consists of the following parts: 110000-101 100 Ohm, +5%, %W Resistor (R70, 75) 410000-102 1K Ohm, +5%, %4W Resistor (R18, 20, 27, 67, 84-86, 94, 110, 128-133) 110000-103 120 Ohm, +5%, %4W Resistor (R1-17, 19, 21, 25, 26, 33, 44, 51-66, 95, 99, 100, 101, 125-127. In addition, for -01 PCB Assy. only: R48, 50) 110000-104 100K Ohm, +5%, %W Resistor (R35-42)

110000-1221.2K Ohm, +5%, %4W Resistor(R46)

110000-151 150 Ohm, +5%, %4W Resistor (R103) 110000-153 15K Ohm, +5%, %4W Resistor (R93) 110000-221 220 Ohm, +5%, “4W Resistor (R24)

110000-2222.2K Ohm, £5%, Y4W Resistor(R45, 92, 102, 112, 114-116, 119-121, 123)

110000-223 22K Ohm, +5%, VW Resistor (R28-32) 110000-270 27 Ohm, +5%, %4W Resistor (R111) 110000-332 3.3K Ohm, +5%, %4W Resistor (R87, 97)

110000-3923.9K Ohm, +5%, %4W Resistor(R47, 49)
110000-471470 Ohm, +5%, %4W Resistor(R34, 104-109)
110000-4724.7K Ohm, +5%, %sW Resistor(R43)

110000-474 470K Ohm, +5%, %4W Resistor (R113, 117, 118, 122)

110000-561560 Ohm, +5%, %4W Resistor(R96)

110000-680 68 Ohm, +5%, %4W Resistor (R124) 110000-821 820 Ohm, + 5%, %W Resistor (For -02 PCB Assy. only: R68, 69, 82, 83) 110003-752, 7.5K Ohm, + 1%, 1/8W Metal-Film Resistor (R71, 72, 76-81, 89) 122000-225 2.2 uf, +10%, 35V Tantalum Capacitor (C87) 122005-103 .01 uf Ceramic-Disc Minimum 25V Radial-Lead Capacitor (C47, 55, 57, 58, 60, 62, 65-68, 71, 91, 92, 95, 96, 99, 100)

137002-001Type 74886 Integrated Circuit(B7)

137149-001 Type 74LS11 Integrated Circuit (J9) 137159-001 Type DAC-08 Digital-to-Analog Converter (C9) 137158-002 OR Type AM6012ADC Digital-to-Analog Converter (A9, D9) For -02 PCB Assemblies only 137160-003 Type MC3410 Digital-to-Analog Converter (B9,E9) For -01 PCB Assemblies only 179010-001 12-Pin PCB Header (J19)

Page 54

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor possession thereof confers or transfers any rightin, or license te use, the subject matter of the drawing or any design of technical information shown thereon, nor any right to reproduce this drawing or any pani thereot, Except for manufacture by vendors of Atari, Inc., ae] and for manufacture under the corporation's writ 2 ten lleense, no right to reproduce this drawing Is 2d granted or the subject matter thereof unless by om fitten agreement with or written permission from 3a the corporation. Qu az ae gz

A> Ey m

Figure 27 Regulator/Audio I! PCB Assembly A035435-02 c

Page 55

Figure 27 Regulator/Audio ll! PCB Assembly Parts List

Part No. Description (Reference Designations and Locations in Bold)

12-52P7 2.7 Ohm, + 5%, 1W Resistor (R5) 16-54PO 4 Ohm, +5%, 5W Wirewound Resistor (R25) 19-100P1015 -1 Ohm, + 3%, 7W Wirewound Resistor (R24) 19-315102 1K Ohm Vertical PCB-Mounting Cermet Trimpot (R8) 24-250108 1000 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C13) 24-250477 470 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C1, 4, 12) 24-350226 22 uf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor (C24, 31) 24-350338 3300 uf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor (C9, 10, 18, 19) 24-500105 1 uf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor (C22, 23) 29-088 -1 uf Ceramic-Disc 25V Radial-Lead Capacitor (C3, 11, 20, 21) 31-A14F 50V 2.5A Miniature Axial-Lead High-Current Rectifier (CR1, 4-8)

33-TIP32PNP Power Transistor, Type TIP32(Q2)

34-2N3055 NPN Silicon Transistor, Type 2N3055 (Q3) 37-LM305 5V Linear Voltage Regulator (Q1)

37-7812+12V Voltage Regulator, Type 7812(Q8)
37-7905—5V Voltage Regulator, Type 7905(Q9)

72-1608C #6-32 x V2" Cross-Recessed Pan-Head Corrosion-Resistant Steel Machine Screw 75-F60405 #6-32 x V4" Binder-Head Nylon Screw 75-99516 #6-32 Nut/Washer Assembly

78-16008Thermally Conductive Compound(Q3)

78-16014 Thermally Conductive Silicon Insulator (Q2, 9)

79-583066-Position Connector Receptacle(J6, 9)
79-583089-Position Connector Receptacle(J7)
79-58346,12-Position Connector Receptacle(J10)
79-583544-Position Connector Receptacle(J8)

020670-01 Test Point 034531-01 Heat Sink 110000-010 1 Ohm, + 5%, %W Resistor (R10, 19) 110000-100 10 Ohm, + 5%, %W Resistor (R11, 20, 29, 30) 110000-101 100 Ohm, + 5%, %W Resistor (R4, 12, 22) 110000-102 1K Ohm, + 5%, YW Resistor (R27, 28) 110000-103 10K Ohm, + 5%, %W Resistor (R13, 14) 110000-271 270 Ohm, + 5%, %4W Resistor (R1) 110000-330 33 Ohm, + 5%, %4W Resistor (R3) 110000-392 3.9K Ohm, + 5%, %4W Resistor (R6) 110000-562 5.6K Ohm, + 5%, %4W Resistor (R32, 33)

110000-7527.5K Ohm, + 5%, %4W Resistor(R7)

110001-221 220 Ohm, + 5%, ¥2W Resistor (R9, 21) 116000-220 22 Ohm, + 5%, 10W Wirewound Resistor (R31) 122002-102 .001 uf Ceramic-Disc 35V Radial-Lead Capacitor (C2, 7, 16)

122004-224.22 uf Ceramic-Disc 25V Capacitor(C6, 8, 15, 17)

122005-103 .01 uf Ceramic-Disc 25V Radial-Lead Capacitor (C5, C14) 137151-002 Type TDA2002A 8W Linear Audio Amplifier Integrated Circuit (Q5, 7)

Page 56

99-10103

PART OF 99-10095

COIN MECHANISM SEE PARTS LIST (71-1200)

98-10102 COIN RETURN { —99-10065 SWITCH WIRE CHUTE 99-10068 _/ SEE PARTS LIST 10075 thru 4002 oo COIN SWITCH ASSY. 0078) FART OF 96-1008) SEE PARTS LIST 99-10008 99-10082 (99-10042 thru 7514128 99-10045)

Figure 28 New Coin Door 71-10xxxx B

Page 57

COIN RETURN BUTTON ASSY.— SEE PARTS LIST (99-10012 thru 99-1022, and 99-10107)

COIN DOOR ONLY— SEE PARTS LIST (99-10009 and 10010)

99-10094

PART OF 99-10074 |

99-10049

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyale, CA. This drawing 1s only conditionally issued, and neither receipt not possession thereof confers or transfers any right in, or license to use,

‘he subject matter of the drawing or any design o!

technical information shown thereon, nor any right to reproduce this drawing or any part thereof. Except for manufacture by vendors of Atarl, inc., and for manufacture under the corporation's writ- {en license, no right to reproduce this drawing is granted or the subject matter thereot unless by written agreement with or written permissien from the corporation COIN RETURN BUTTON COVER— SEE PARTS LIST (99-10055 thru 99-10059)

PRICE PLATE— SEE PARTS LIST (99-10070, 99-10083 thru 99-10092, and 99-10108) 99-10074

72-JA1405B

99-10062

72-HA1404C

99-10061

99-10066

75-9158 q

72-JA1405B

99-10051

Figure 28 New Coin Door 71-10xxxx B

Page 58

Figure 28 New Coin Door, continued Parts List

Part No. Description

31-1N4002 100V Silicon Rectifier 1N4002 Diode 65-4416 General-usage low-iorce miniature switch 70-11-47 Miniature bayonet-base incandescent lamp, type #47 71-1201ADU U.S. $1.00 coin mechanism 71-1201FCH Swiss 1 Fr coin mechanism 74-1201MG German 1 DM coin mechanism 71-1202MG German 2 DM coin mechanism 71-1205FB Belgian 5 Fr coin mechanism 71-1205MG German 5 DM coin mechanism 71-1210PE U.K. 10 P coin mechanism

71-1220CA Australian 20¢ coin mechanism 71-1225CU U.S. 25¢ coin mechanism 71-12100LI Italian 100 Lire coin mechanism 71-12100YJ Japanese Y100 coin mechanism 72-HA1404C #4x%" Slotted pan-head thread-rolling tri-fluted “Taptite” cadmium-plated screw 72-JA1405B #4x5/16” Slotted pan-head thread-rolling tri-fluted “Plastite” black screw 72-9406S #4-40x3/8” Slotted truss-head steel machine screw 72-9603S #6-32x3/16" Slotted truss-head steel machine screw 75-915S. #1%-20 Standard pattern cadmium-plated steel hex nut 75-9188, #8-32 Standard pattern cadmium-plated steel hex nut 75-944S #4-40 Poiymer self-locking steel hex nut 75-948S #8-32 Polymer self-locking steel hex nut 75-1408S #4-40x¥2" Slotted pan-head steel machine screw 75-1412S #4-40x34" Slotted pan-head steel machine screw 75-5520B #¥%4-20x1%4" Round-head square-neck steel bolt with black finish 99-10008 Switch wire retainer 99-10009 2-Mech coin door only 99-10010 3-Mech coin door only 99-10011 Inner panel 99-10012 U.S, 25¢ coin return button assembly 99-10013 U.S. $1.00 coin return button assembly 99-10014 German 1 DM coin return button assembly 99-10015 German 2 DM coin return button assembly 99-10016 German 5 DM coin return button assembly 99-10017 Belgian 5 Fr coin return button assembly 99-10018 Swiss 1 Fr coin return button assembly 99-10019 Japanese Y100 coin return button assembly 99-10020 U.K. 10 P coin return button assembly 99-10021 Australian 20¢ coin return button assembly 99-10022 Italian 100 Lire coin return button assembly 99-10040 Coin inlet chute assembly 99-10041 Coin counter assembly 99-10042 Coin switch assembly for U.S. 25¢ and Belgian 5 Fr coins (silver wire) 99-10043 Coin switch assembly for German 1 DM, Swiss 1 Fr, and Japanese Y100 coins (black wire) 99-10044 Coin switch assembly tor U.S. $1.00, German 2 DM, and Italian 100 Lire coins (gold wire)

Page 59

Figure 28 New Coin Door, continued Parts List

Part No. Description

99-10045 Coin switch assembly for German 5 DM, U.K. 10 P, and Australian 20¢ coins (green wire) 99-10047 Lockout coil assembly 99-10048 Coin door harness assembly 99-10049 Locking arm assembly 99-10051 Coin door frame 99-10052 Coin return lever 99-10054 Coin button housing 99-10055, Coin return button cover for Japanese Y100 coin 99-10056 Coin return button cover for German 1 DM and Swiss 1 Fr coins 99-10057 Coin return button cover for U.S. 25¢ and Belgian 5 Fr coins 99-10058 Coin return button cover for U.S. $1.00, German 2 DM, and Italian 100 Lire coins 99-10059 Coin return button cover for German 5 DM, U.K. 10 P, and Australian 20¢ coins 99-10061 Coin return bezel 99-10062 Coin return button 99-10063 Right half of coin inlet chute 99-10064 Left half of coin inlet chute 99-10065 Coin return box 99-10066 Coin return cover 99-10070 U.S. 25¢ price plate 99-10071 Slam switch assembly 99-10073 Test switch decal 99-10074 Lock assembly 99-10075 Black switch wire—for German 1DM, Swiss 1Fr and Japanese Y100 coins 99-10076 Silver switch wire—for U.S. 25¢ and Belgian 5Fr coins 99-10077 Gold switch wire—for U.S. $1.00, German 2DM and Italian 100 Lire coins 99-10078 Green switch wire—for German 5DM, U.K. 10P and Australian 20¢ coins 99-10080 Miniature bayonet-base lamp socket 99-10081 Wire key holder 99-10082 Switch cover 99-10083 U.S. $1.00 price plate 99-10084 German 1 DM price plate 99-10085 German 2 DM price plate 99-10086 German 5 DM price plate 99-10087 Belgian 5 Fr price plate 99-10088 Swiss 1 Fr price plate 99-10089 Japanese Y100 price plate 99-10090 U.K. 10 P price plate 99-10091 Australian 20¢ price plate 99-10092 Italian 100 Lire price piate 99-10094 Fish paper insulation 99-10095 Toggle switch 99-10096 “U”-type fastener 99-10097 Fish paper insulation 99-10101 Coin inlet chute sub-assembly 99-10102 Switch and lockout coil bracket sub-assembly 99-10103 Inner panel with levers sub-assembly 99-10104 Anti-penny-flip bar retainer 99-10105 Anti-penny-flip bar 99-10107 U.S. 50¢ coin return button assembly 99-10108 U.S. 50¢ price plate—for two quarters

Page 60

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 61

te 1st printing

YOUR COMMENTS, PLEASE!

Your comments will assist Atari in improving the usefulness of our publications. They are an important part of preparing for revisions of manuals and parts catalogs. No postage stamp is necessary if mailed in the U.S.A.

If you have any technical questions about certain Atari or Kee Games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply:

Name Firm O Distributor

Address CO Operator City State Zip Ci Other.

Page 62

First fold

BUSINESS REPLY MAIL

FIRST CLASS PERMIT NO. 1004 SUNNYVALE, CA

POSTAGE WILL BE PAID BY ADDRESSEE

Atari, Inc. Attn.: Field Service/Coin-Op Division P. O. Box 427 Sunnyvale, California 94086 No Postage Necessary if mailed in the United States

=~

Cut along this line

Second fold

eBpe siuy edey sWol4

Page 63

@ RRR EEE ES

P ° ° > ° >

Warranty

Seller warrants that its printed circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its television monitors (in games supplied with monitors) are free from defects in material and workmanship under normal use and service for a period of thirty

  • days from date of shipment. None of the Seller's other products or parts thereof are warranted.

If the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are returned to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
  • Such products are returned prepaid to Sellers’ plant; and
  • Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing.

In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages.

Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms of this order, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products under this order.

SEE RES ES EE The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to yourself and others. Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety.

Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.

This document is and contains confidential trade secret information of Atari, Inc.

This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for any other. purpose whatever, and remains the property of Atari, Inc.

Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc. © © © S

© s IS

Page 64

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.