CATHODE RAY TOMES

Air Trix DX

Air Trix (Rev A) (Sega / Hitmaker, 2000) · Manual · 166 pages · 244 sections · original scan

Page 1

A

MANUAL NO. 420-6614-01 Gj E

DX Type

+

Owner’s Manual

| — an] =~ oc bas}

= =

SEGA ENTERPRISES, INC. USA 1ST PRINTING JAN. 01

Page 2

Warranty

Your new Sega Product is covered for a period of 90 days from the date of shipment. This certifies that the Printed Circuit Boards, Power Supplies and Monitor are to be free of defects in workmanship or materials under normal operating conditions. This also certifies that all Interactive Control Assemblies are to be free from defects in workmanship and materials under normal operating conditions. No other product in this machine is hereby covered.

Sellers sole liability in the event a warranted part described above fails shall be, at its option, to replace or repair the defective part during the warranty period. For Warranty claims, contact your Sega Distributor.

Should the Seller determine, by inspection that the product was caused by Accident, Misuse, Neglect, Alteration, Improper Repair, Installation or Testing, the warranty offered will be null and void.

Under no circumstances is the Seller responsible for any loss of profits, loss of use, or other damages.

This shall be the exclusive written Warranty of the original purchaser expressed in lieu of all other warranties expressed or implied. Under no circumstance shall it extend beyond the period of time listed above.

Page 3

BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWING: To maintain the safety:

To ensure the safe usage of the product, be sure to read the following before using the product. The following instructions are intended for the users, operators and the personnel in charge of the operation of the product. After carefully reading and sufficiently understanding the warning displays and cautions, handle the product appropriately. Be sure to keep this manual nearby the product or elsewhere convenient for referring to it when necessary.

Herein, explanations which require special attention are enclosed with dual lines. Depending on the potentially hazardous degrees, the terms of WARNING, CAUTION, etc. are used. Be sure to understand the contents of the displays before reading the text.

Indicates that mishandling the Indicates that mishandling the product product by disregarding this by disregarding this caution will cause

warning will cause a potentially a slight hazardous situation which can
WARNING! hazardous situation which can CAUTION! result in personal injury and or material result in death or serious injury. damage.

For the sage usage of the product, the following pictographs are used:

Indicates “HANDLE WITH CARE.” In order to protect the human body an equipment, this display is attached to places where the Owner’s Manual and or Service Manual should be referred to.

© Perform work in accordance with the instructions herein stated. Instructions for work are explained by paying attention to the aspect of accident prevention. Failing to perform work as per the instructions can cause accidents. In the case where only those who have technical expertise should perform the work to avoid hazardous situation, the instructions herein state that the serviceman should perform such work.

© Be sure to turn off power before working on the machine. To prevent electric shock, be sure to turn off power before starting the work in which the worker touches the interior of the product. If the work is to be performed in the power-on status, the Instruction Manual herein always states to that effect.

O Besure to ground the Earth Terminal (this, however, is not required in the case where a power cord with earth is used). This product is equipped with the Earth Terminal. When installing the product, Connect the Earth Terminal to the “accurately grounded indoor earth terminal” by using an earth wire. Unless the product is grounded appropriately, the user can be subject to electric shock. After performing repair, etc. for the Control equipment, ensure that the Earth Wire is firmly connected to the Control equipment.

© Ensure that the Power Supply used is equipped with an Earth Leakage Breaker. This product does not incorporate the Earth Leakage Breaker. Using a power supply which is not equipped with the Earth Leakage Breaker can cause a fire when earth leakage occurs.

© Be sure to use fuses which meet the specified rating. (only for the machines which use fuses). Using fuses exceeding the specified rating can cause a fire and electric shock.

Page 4

© _ Specification changes (removal of equipment, conversion and addition) not designated by SEGA are not allowed. The parts of the product include warning labels for safety, covers for personal protection, etc. It is very hazardous to operate the product by removing parts and or modifying the circuits. Should doors, lids and protective parts be damaged or lost, refrain from operating the product, and contact where the product was purchased from or the office herein stated. SEGA shall not be held responsible for any accidents, compensation for damage to a third party, resulting from the specifications not designated by SEGA. ©. Ensure that the product meets the requirements of appropriate Electrical Specifications. Before installing the product, check for Electrical Specifications. SEGA products have a nameplate on which Electrical Specifications are described. Ensure that the product is compatible with the power supply voltage and frequency requirements of the location. Using any Electrical Specifications different from the designated Specifications can cause a fire and electric shock. © _ Install and operate the product in places where appropriate lighting is available, allowing warning labels to be clearly read. To ensure safety for the customers, labels and printed instructions describing potentially hazardous situation are applied to places where accidents can be caused. Ensure that where the product is operated has sufficient lighting allowing the warnings to be read. If any label is peeled off, apply it again immediately. Please place an order with where the product was purchased from or the office herein stated. © When handling the Monitor, be very careful. (Applies only to the product w/monitor.) Some of the monitor (TV) parts are subject to high tension voltage. Even after running off power, some portions are still subject to high tension voltage sometimes. Monitor repair and replacement should be performed only be those technical personnel who have knowledge of electricity and technical expertise. © Besure to adjust the monitor (projector) properly. (Applies only to the product w/monitor.) Do not operate the product leaving on-screen flickering or blurring as it is. Using the product with the monitor not properly adjusted may cause dizziness or a headache to an operator, a player, or the customers. © _ When transporting or reselling this product, be sure to attach this manual to the product. In the case where commercially available monitors and printers are used in this product, only the contents relating to this product are explained herein. Some commercially available equipment has functions and reactions not stated in this manual. Read this manual together with the specific Instruction Manual of such equipment.

  • Descriptions herein contained may be subject to improvement changes without notice. © The contents described herein are fully prepared with due care. However, should any question arise or errors be found, please contact SEGA.

INSPECTIONS IMMEDIATELY AFTER TRANSPORTING THE PRODUCT TO THE LOCATION.

Normally, at the time of shipment, SEGA products are in a status allowing for usage immediately after transporting to the location. Nevertheless, an irregular situation may occur during transportation. Before turning on power, check the following points to ensure that the product has been transported in a satisfactory status. Are there any dented portions or defects (cuts, etc.) on the external surfaces of the cabinet? Are Casters and Adjusters, damaged? Do the power supply voltage and frequency requirements meet with those of the location? Are all wiring connectors correctly and securely connected? Unless connected in the correct direction, connector connections can not be made accurately. Do not insert connectors forcibly. Do power cords have cuts and dents? Do the fuses used meet specified rating? Is the Circuit Protector in an energized status? Are all accessories available? Can all Doors and Lids be opened with the Accessory keys? Can Doors and Lids be firmly closed?

Page 5

TABLE OF CONTENTS

BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWING: TABLE OF CONTENTS,

INTRODUCTION OF THE OWNER'S MANUAL

  • HANDLING PRECAUTIONS .
  • PRECAUTIONS CONCERNING INSTALLATION LOCATION
  • OPERATION .4-
  • NAME OF PARTS . 9
  • ACCESSORIES .... 10 - 12
  • ASSEMBLING AND INSTALLATION 13-27
  • PRECAUTIONS TO BE HEEDED WHEN MOVING THE MACHINE 28-30
  • CONTENTS OF GAME... 31-37
  • EXPLANATION OF TEST AND DATA DISPLAY 38 - 60

9-1 SWITCH UNIT AND COIN METER .. . 39

9-2 SYSTEM TEST MODE 40-51

9-3 GAME TEST MODE... 52 - 60

  • MAINTENANCE OF CONTROLLER MECHANISM UNIT 61-80

10-1 ADJUSTING/REPLACING THE ROLL-DIRECTION VOLUME CONTROL .. . 61-66 10-2 ADJUSTING/REPLACING THE YAW-DIRECTION

VOLUME CONTROL . 67-70

10-3 GREASING 71-77

10-4 REPLACING THE ACCIDENT AVOIDANCE SYSTEM 78 - 80

  • PROJECTOR 81-94

11-1 CLEANING THE SCREEN 81

11-2 ADJUSTMENT OF TOSHIBA PROJECTOR .... .. 82-91

11-3 ADJUSTMENT OF MITSUBISHI PROJECTOR . 92-94

  • COIN SELECTOR, . 95
  • REPLACING THE FLUORESCENT LAMP, AND LAMPS . 96 - 103
  • PERIODIC INSPECTION TABLE 104
  • TROUBLESHOOTING .... 105 - 107

15-1 TABLE OF TROUBLESHOOTING .. 105 - 106

15-2 SYSTEM ERROR MESSAGES .... 107

  • GAME BOARD . 108-110 16-1 REMOVING THE GAME BOARD .. 108 - 109 16 - 2 COMPOSITION OF GAME BOARD 110
  • DESIGN RELATED PARTS, ll
  • PARTS LIST......... 112 - 156
  • WIRE COLOR CODE TABLE vse, 157
  • WIRING DIAGRAM .. 158 - 160
Page 6

SPECIFICATIONS

Installation space : 1,315 mm (W) X 2, 845 mm (D) (51.8 in. X 112.0 in.) Height : 2,298 mm (90.4 in.) Weight : Approx. 535 kg. (1,179.5 Ibs.) Power, maximum current : 570 W 6.45 A (AC 110V 50 Hz AREA) 560 W 6.30 A (AC 110V 60 Hz AREA) 555 W 5.70 A (AC 120V 60 Hz AREA) 570 W 3.50 A (AC 220V 50 Hz AREA) 560 W 3.40 A (AC 220V 60 Hz AREA) 560 W 3.35 A (AC 230V 50 Hz AREA) 555 W 3.25 A (AC 230V 60 Hz AREA) 565 W 3.25 A (AC 240V 50 Hz AREA) 555 W 3.15 A (AC 240V 60 Hz AREA) For TAIWAN (TOSHIBA PROJECTION DISPLAY TYPE) Power, current : 575 W 6.75A (MAX.) 360 W 4.10A (MIN.) For TAIWAN (MITSUBISHI PROJECTION DISPLAY TYPE) Power, current : 565 W 6.40A (MAX.) 345 W 3.95A (MIN.) MONITOR : 29 TYPE COLOR MONITOR

INTRODUCTION OF THE OWNERS MANUAL

This Owner's Manual is intended to provide detailed descriptions together with all the necessary information covering the general operation of electronic assemblies, electromechanicals, servicing control, spare parts, etc. as regards the product, AIR TRIX. This manual is intended for the owners, personnel and managers in charge of operation of the product. Operate the product after carefully reading and sufficiently understanding the instructions. If the product fails to function satisfactorily, nontechnical personnel should under no circumstances touch the internal system. Please contact where the product was purchased from.

Use of this product is unlikely to cause physical injuries or damages to property. However, where special attention is required this is indicated by a thick line, the word "IMPORTANT" and its sign in this manual.

Indicates that mishandling the product by disregarding this display can cause the product's intrinsic performance not to be obtained, resulting in malfunctioning.

IMPORTANT

SEGA ENTERPRISES, INC. (U.S.A.)/CUSTOMER SERVICE 45133 Industrial Drive, Fremont, California 94538, U.S.A. Phone : (415) 701-6580 Fax : (415) 701-6594

Page 7

DEFINITION OF LOCATION MAINTENANCE MAN AND SERVICEMAN

WARNING! Non-technical personnel who do not have technical knowledge and expertise should refrain from performing such work that this manual requires the location's maintenance man or a serviceman to carry out, or work which is not explained in this manual. Failing to comply with this instruction can cause a severe accident such as electric shock.

Ensure that parts replacement, servicing & inspections, and troubleshooting are performed by the location's maintenance man or the serviceman. It is instructed herein that particularly hazardous work should be performed by the serviceman who has technical expertise and knowledge.

The location's maintenance man and serviceman are herein defined as follows:

"Location's Maintenance Man" : Those who have experience in the maintenance of amusement equipment and vending machines, etc., and also participate in the servicing and control of the equipment through such routine work as equipment assembly and installation, servicing and inspections, replacement of units and consumables, etc. within the Amusement Facilities and or locations under the management of the Owner and Owner's Operators of the product.

Activities of Location's Maintenance Man : Assembly & installation, servicing & inspections, and replacement of units & consumables as regards amusement equipment, vending machines, etc.

Serviceman : Those who participate in the designing, manufacturing, inspections and maintenance service of the equipment at an amusement equipment manufacturer. Those who have technical expertise equivalent to that of technical high school graduates as regards electricity, electronics and or mechanical engineering, and daily take part in the servicing & control and repair of amusement equipment.

Serviceman's Activities : Assembly & installation and repair & adjustments of electrical, electronic and mechanical parts of amusement equipment and vending machines.

Page 8
  • HANDLING PRECAUTIONS

When installing or inspecting the machine, be very careful of the following points and pay attention to ensure that the player can enjoy the game safely. Non-compliance with the following points or inappropriate handling running counter to the cautionary matters herein stated can cause personal injury or damage to the machine.

without turning power off can cause an electric shock or short circuit. In the case work should be performed in the status of power on, this manual always states to that effect. To avoid electric shock or short circuit, do not plug in or unplug quickly. To avoid electric shock, do not plug in or unplug with a wet hand. Do not expose Power Cords and Earth Wires on the surface, (floor, passage, etc.). If exposed, the Power Cords and Earth Wires are susceptible to damage. Damaged cords and wires can cause electric shock or short circuit.

To avoid causing a fire or electric shock, do not put things on or damage

Power Cords. When or after installing the product, do not unnecessarily pull the power cord. f damaged, the power cord can cause a fire or electric shock. n case the power cord is damaged, ask for replacement through where the product was purchased from or the office herein stated. Using the cord as is damaged can cause fire, electric shock or leakage. Be sure to perform grounding appropriately. Inappropriate grounding can cause an electric shock. Be sure to use fuses meeting specified rating. Using fuses exceeding the

A @ Before performing work, be sure to turn power off. Performing the work

WARNING!

specified rating can cause a fire or electric shock. Completely make connector connections for IC BD and others. Insufficient insertion can cause an electric shock. Specification changes, removal of equipment, conversion and/or addition, not designated by SEGA are not permitted.

Failure to observe this may cause a fire or an electric shock. Non-compliance

with this instruction can have a bad influence upon physical conditions of the players or the lookers-on, or result in injury during play. SEGA shall not be held responsible for damage, compensation for damage to a third party, caused by specification changes not designated by SEGA. Be sure to perform periodic maintenance inspections herein stated.

For the IC board circuit inspections, only the logic tester is allowed. The use of a multiple-purpose tester is not permitted, so be careful in this regard. The Projector is employed for this machine. The Projector's screen is susceptible to damage, therefore, be very careful when cleaning the screen. For details, refer to PROJECTOR.

IMPORTANT
Page 9
  • PRECAUTIONS CONCERNING INSTALLATION

LOCATION

WARNING! This product is an indoor game machine. Do not install it outside. Even indoors, avoid installing in places mentioned below so as not to cause a fire, electric shock, injury and or malfunctioning. @ Places subject to rain or water leakage, or places subject to high humidity in the proximity of an indoor swimming pool and or shower, etc. Places subject to direct sunlight, or places subject to high temperatures in the proximity of heating units, etc. laces filled with inflammable gas or vicinity of highly inflammable/volatile chemicals or hazardous matter. Dusty places. Sloped surfaces. Places subject to any type of violent impact. Vicinity of anti-disaster facilities such as fire exits and fire extinguishers. The operating (ambient) temperature range is from 5 Celsius to 40 Celsius. Only in the case a projector is employed, the temperature range is from 5 Celsius to 30 Celsius.

LIMITATIONS OF USAGE REQUIREMENTS

WARNING! Be sure to check the Electrical Specifications. Ensure that this product is compatible with the location's power supply, voltage and frequency requirements. A plate describing Electrical Specifications is attached to the product. Non-compliance with the Electrical Specifications can cause a fire and electric shock. This product requires the Breaker and Earth Mechanisms as part of the

location facilities. Using them in a manner not independent can cause a fire

and electric shock. Ensure that the indoor wiring for the power supply is rated at 15A or higher (AC single phase 100 ~ 120V area), and 10A or higher (AC 220 ~ 240V

area). Non-compliance with the Electrical Specifications can cause a fire and

electric shock. Be sure to independently use the power supply equipped with the Earth Leakage Breaker. Using a power supply without the Earth Leakage Breaker can cause an outbreak of fire when earth leakage occurs. Putting many loads on one electrical outlet can cause generation of heat and a fire resulting from overload. When using an extension cord, ensure that the cord is rated at 15A or higher (AC 100 ~ 120V area) and 10A or higher (AC 220 ~ 240V area). Using a cord rated lower than the specified rating can cause a fire and electric shock.

Page 10

OPERATION AREA

A @ For the operation of this machine, secure a minimum area of 1.9m (W) X 3m

(D). In order to prevent injury resulting from the falling down accident

WARNING! during game play, be sure to secure the minimum area for operation. : @ Be sure to provide sufficient space so as to allow this product's ventilation fan

to function efficiently. To avoid machine malfunctioning and a fire, do not

place any obstacles near the ventilation opening. SEGA shall not be held responsible for damage, compensation for damage to a third party, resulting from the failure to observe this instruction.

S For transporting the machine into the location's building, the minimum necessary dimensions of the opening (of doors, etc.) are 1.3m(W) and 1.7m(H).

IMPORTANT

Electric current consumptionSaalaMy4,YYj Yy
SLLLLLLL.LLLY
MAX. 6.45 A (AC 110V 50 Hz)ZAY
MAX. 6.30 A (AC 110V 60 Hz)Wi,=aUy
MAX. 5.70 A (AC 120V 60 Hz)Uy“Yj
MAX. 3.50 A (AC 220V 50 Hz)YyYy

MAX. 3.40 A (AC 220V 60 Hz) MAX. 3.35 A (AC 230V 50 Hz) MAX. 3.25 A (AC 230V 60 Hz) MAX. 3.25 A (AC 240V 50 Hz) MAX. 3.15 A (AC 240V 60 Hz) MX A [| XX SS

For TAIWANY/

TOSHIBA projection display =

MAX. 6.75 AekY y[|YY
MITSUBISHI projection display|=Wy
MAX. 6.40 AUyv=YY
YZ)—=Y
WY—Yy

“4 Y/

458.4 1900

FIG. 2

Page 11
  • OPERATION

PRECAUTIONS TO BE HEEDED BEFORE STARTING THE OPERATION

To avoid injury and trouble, be sure to constantly give careful attention to the behavior and manner of the visitors and players.

A In order to avoid accidents, check the following before starting the operation: @ To ensure maximum safety for the players and the customers, ensure that

WARNING! where the product is operated has sufficient lighting to allow any warnings to be read. Operation under insufficient lighting can cause bodily contact with each other, hitting accident, and or trouble between customers. @ Be sure to perform appropriate adjustment of the monitor (projector). For operation of this machine, do not leave monitor's flickering or deviation as is. Failure to observe this can have a bad influence upon the players' or the customers' physical conditions. It is suggested to ensure a space allowing the players who feel sick while playing the game to take a rest. Check if all of the adjusters are in contact with the surface. If they are not, the Cabinet can move and cause an accident.

Ensure that all of the Adjusters are in contact with the floor.

Page 12

the product with the hazard preventive parts as is left in an irregular status

A @ Check to see if hazard preventive parts are damaged or omitted. Operating

will cause accidents.

WARNING!

By carrying out a test run, check that the Skateboard can normally be locked and unlocked.

Check that the side guard panel has not cracked or dropped out?

Check that the handrails do not rattle. N\

Check that the Skateboard can normally be locked and unlocked.

Check that the bellows have not torn. a“

Do not put any heavy item on this product. Placing any heavy item on the product can cause a falling down accident or parts damage. Do not climb on the product. Climbing on the product can cause falling down accidents. To check the top portion of the product, use a step. To avoid electric shock, check to see if door & cover parts are damaged or omitted. To avoid electric shock, short circuit and or parts damage, do not put the following items on or in the periphery of the product. Flower vases, flowerpots, cups, water tanks, cosmetics, and receptacles/ containers/vessels containing chemicals and water.

crowded situation at the installation location. Insufficient installation space can cause making bodily contact with each other, hitting accidents, and or trouble between customers. f\ To avoid injury, be sure to provide sufficient space by considering the potentially

CAUTION!
Page 13

PRECAUTIONS TO BE HEEDED DURING OPERATION (PAYING ATTENTION TO CUSTOMERS)

To avoid injury and trouble, be sure to constantly give careful attention to the behavior and manner of the visitors and players.

are not allowed to play the game. Those who need assistance such as the use of an apparatus when walking.

WARNING! Those who have high blood pressure or a heart problem. Those who have experienced muscle convulsion or loss of consciousness when playing video game, etc. Those who have a trouble in the neck and or spinal cord. Intoxicated persons. Pregnant women or those who are in the likelihood of pregnancy. Persons susceptible to motion sickness. Persons whose act runs counter to the product's warning displays. A player who has never been adversely affected by light stimulus might experience dizziness or headache depending on his physical condition when playing the game. Especially, small children can be subject to those conditions. Caution guardians of small children to keep watch on their children during play. Instruct those who feel sick during play to have a medical examination. To avoid injury resulting from falling down and electric shock due to spilled drinks, instruct the player not to place heavy items or drinks on the product. To avoid electric shock and short circuit, do not allow customers to put hands

and fingers or extraneous matter in the openings of the product or small

openings in or around the doors. To avoid falling down and injury resulting from falling down, immediately stop the customer's leaning against or climbing on the product, etc. To avoid electric shock and short circuit, do not allow the customers to unplug the power plug without a justifiable reason.

( @ To avoid injury and accidents, those who fall under the following categories

The player should be able to get on the Skate Board and hold on firmly to the Safety Bar. To avoid falling down accidents, instruct those who are shorter than 130 cm. not to play the game as the height of the Safety Bar is approximately 130 cm. Approx. 130cm Instruct those who wear high-heeled shoes to refrain from playing the game by explaining that playing game with high-heeled shoes is very likely to cause potentially hazardous situation.

Page 14

@ To avoid injury from potential falling down accidents, be sure to instruct that only one person is 'ARNING! W Gl allowed to play at a time.

Do not allow players to put any heavy item or beverages on the product. Falling down items can cause accidents and spilled beverages can cause electric shock.

the customers who are most likely to cause injury by playing without holding

() Instruct the player to hold on firmly to the Safety Bar during game. Caution

the Safety Bar, for example.

CAUTION!
Page 15

persons other than the player to standing on both feet. Standing

CAUTION! access to the Rear Cabi during on one leg to play can cause

: game play.

AY @ 1 avoid injury, do not allow @ Instruct the player to play by

@ Instruct the player not to put Regarding this product, the

baggages, etc. on the Rear Cabi to weight of the player is limited to

avoid damaging such items. 150 kg. To avoid machine damage and injury due to machine damage, playing by those who are as heavy as 150 kg. or heavier is strictly prohibited.

@ Immediately stop such violent acts as hitting and kicking the product. Such violent acts can cause parts damage or falling down, resulting in injury due to fragments and falling down.

Page 16
  • NAME OF PARTS

BILLBOARD

FRONT CABI ie PTV 50 Type Projector

SWITCH PANEL

COIN CHUTE DOOR

SIDE POP

CASHBOX DOOR

SAFETY BAR

AC UNIT

PTV BASE N& IN

REAR CABI SKATE BOARD

FOOT CONTROLLER

FIG.4 OVERVIEW

PHOTO 4 ASSY TUBE

TABLE 4

Width X = Length X Height Weight

PTV (50 type Projector)1,140mmX555mm =X1,670mm119 kg
PTV BASE (FRONT CABI)1,190mmX 1,020mmX785mm70 kg
BILLBOARD1128mmX440mmX400mm20 kg
REAR CABI990mmX 1,620mmX1,140mm256 kg
When assembled1,740mm=X 2,740 mmX 2,325 mm467 kg
Page 17
  • ACCESSORIES

When transporting the machine, make sure that the following parts are supplied.

TABLE 5 ACCESSORIES

DESCRIPTIONOWNERS MANUALKEY MASTERKEY
Part No. (Qty.)420-6614-01 (1)220-5576 (2)(2)
NoteFor opening/closingFor the CASHBOX DOOR

the doors Figures If Part No. has no description, the Number has not been fia \ au registered or can not be registered. Such a part may not Tan G be obtainable even if the customer desires to purchase it. Therefore, ensure that the part is in safekeeping with you. The Keys are inside the Coin Chute Door at the time of VOL CONT B-5K OHM GREASE GUN KH-120 shipment from the factory. 220-5484 (1) 540-0064 (1) Spare, see Section 10. For greasing, see Section 10.

LAMP 6V 3W (WEDGE BULB) 390-5160 (1) Spare, refer to Section 13.

GREASE ALBAMIA EP-1 400G (SPECIAL GREASE) 090-0275 (1) For greasing, see Section 10.

CARTON BOX TOSHIBA MITSUBISHI 601-10642 (1) Remote Controller used for Remote Controller used for adjustment of the projector. adjustment of the projector. See Section 11. See Section 11. 200-5536(1) 200-5532(1) Used for transporting the Game Board. Refer to FIG. 15.

One of the above 2 types of Remote Controllers is used for the Projector. The Remote Controller is attached to the Projector at the time of shipment.

Page 18

HOW TO USE THE CARTON BOX

@ When asking for the replacement or repair of the product's Game Board (SEGA HIKARU), be sure to put the Game Board together with the Shield Case in a Carton Box. Otherwise, the request is not acceptable. Put the Shield Case in the Carton Box by paying attention to the correct direction as per the following instructions and as shown by the instructions printed on the Carton Box. Handling in an erroneous manner can damage the Game Board. Remove the Shield Case Brackets from the Shield Case and put the Shield Case in the Carton Box.

SHIELD CASE BRACKETS The shape depends on the type of product.

"CHECK SIDE" Display

Wrap the Shield Case with the packing material and put it in the Carton Box as shown. Putting it upside down or packing otherwise in the manner not shown can damage the Game Board and parts. FILTER BOARD,

FIG. 5

Page 19

The following Table 5b lists the parts that had been separately packed when the product was shipped from the factory but are necessary when you use the product. These parts will be mounted on the product when installing and assembling it.

TABLE 5b

SIDE POP ATR-0003 (2) of Section 6. AC Cable (Power Cord) 600-6724 600-6729 (1) TAIWAN

600-6619 (1) HONG KONG 600-6618 (1) AC 220 ~ 240V AREA 600-6695 (1) USA Used for installation, see[ 5] of Section 6.

CORD CLAMP 280-5009-01 (1) Used for securing the power cord. see[5] of Section 6.

WIRE HARN EARTH W/LUG M6, 600-6664-02 (1) For TAIWAN. Used for installation, see[ 5] of Section 6.

Page 20
  • ASSEMBLING AND INSTALLATION
WARNING!

AN

CAUTION! Perform assembly work by following the procedure herein stated. Failing to comply with the instructions can cause electric shock hazard. Perform assembling as per this manual. Since this is a complex machine, erroneous assembling can cause an electric shock, machine damage and or not functioning as per specified performance. When assembling, be sure to use plural persons. Depending on the assembly work, there are some cases in which working by one person alone can cause personal injury or parts damage. Ensure that connectors are accurately connected. Incomplete connections can cause electric shock hazard. Be careful so as not to damage wirings. Damaged wiring can cause electric shock and short circuit hazards. Do not carelessly push the PTV. Pushing the PTV carelessly can cause the PTV to fall down. This work should be performed by the Location's Maintenance Man or Serviceman. Performing work by non-technical personnel can cause a severe accident such as electric shock. Failing to comply with this instruction can cause a severe accident such as electric shock to the player during operation. Provide sufficient space so that assembling can be performed. Performing work in places with narrow space or low ceiling may cause an accident and assembly work to be difficult. To perform work safely and avoid serious accident such as the cabinet's falling down, do not perform work in places where step-like grade differences, a ditch, or slope exist.

When handling plastic parts, use care. Do not give a shock or apply excessive load to the fluorescent lamps and plastic parts. Failure to observe this can cause parts damage, resulting in injury due to fragments, cracks and broken pieces. To perform work safely and securely, be sure to prepare a step which is in a secure and stable condition. Performing work without using the step can cause violent falling down accidents.

Page 21

When carrying out the assembly work, follow the procedure in the following 7-item sequence:

ASSEMBLING THE PTV (FRONT CABI)

WIRING CONNECTIONS BETWEEN THE CABINETS

SECURING IN PLACE (ADJUSTER ADJUSTMENT)

INTALLING THE SIDE POP

POWER SUPPLY, AND EARTH CONNECTION

TURNING POWER ON

ASSEMBLY CHECK Na] [a] fa) NJ [ea] IJIN

The master key (accessories) in addition to the tools such as a Phillips type screwdriver, Box nut screwdriver and wrench are required for the assembly work.

Phillips type screwdriver (for M4,MS5 screw) WRENCH (for M16 hexagon bolt)

Box nut screwdriver KEY MASTER SJ smm (For M4 hexagon nut)

Page 22

WA ASSEMBLING THE PTV (FRONT CABI) ® By using the specified screws, secure the 2 Mask Holders to the PTV ceiling

® By using the specified screws, secure the 2 Mask Holders to the PTV ceiling.

@ Insert the TV Mask from the underside as shown and secure with a total of 6 screws.

FLAT HEAD SCREW (2 each) M4 X 12

MASK HOLDER

TRUSS SCREW (2) MS X 25, flat washer used, chrome plated

\ SCREW (4), black \ ? M5 X 20, w/flat & FIG.6.1a spring washers

In order to prevent accidents during assembly work, have all of the Adjusters of the PTV Base make contact with the surfaces to secure the PTV Base.

For performing work, use 4 or more workers.

FIG. 6. 1b

Page 23

® Mount the assembled PTV on the PTV Base. After mounting the PTV, move it to the rear part of the PTV Base. When performing this work, be sure to use 4 or more persons. (FIG. 6. 1 b)

© install Panel Mount Bracket L and R to the front of the PTV by using 2 screws for each of them.

Connecting the 3 connectors to the connector panel

PANEL MOUNT BRACKET L

FRONT PANEL

TRUSS SCREW (4), black MS X 20, flat washer used.

HOLE LID

TRUSS SCREW (3 each), black, M4 X 20

SCREW (2 each), black M5 X 20, w/flat & spring washers

SCREW (2 each), black”

M4 X 10, w/flat & spring washers 4 FIG. 6.1¢

© Connect the 3 connectors (2 for power supply, 1 for video signal) of the wires already connected to the PTV Base, to the 3 connectors on the PTV connector panel. The connectors can be inserted only in the fixed orientation. If you attempt to apply constrained force when inserting the connector, it may break. Fully make sure that it is in the correct orientation. The reflection signal connector has the securing screws at the both ends. After connecting, fasten the screws tightly.

PHOTO 6. 1a

Page 24

@ install the Front Panel to the front

of PTV. Use the 4 truss screws for

securing.

TRUSS SCREW (4), black, MS X 20, flat washer used.

PHOTO 6. 1b

Install the 2 Hole Lids to the bottom of the Front Panel. For each of these, use the 2 screws and 3 truss screws for securing.

Note that different screws must be used for the Front Panel and PTV Base. HOLE LID

SCREW (2 each), black M4 X 10, w/flat & spring washers

TRUSS SCREW (3 each), black, M4 X 20

PHOTO 6.1 ¢

This work must be performed by two persons: Place the Billboard on the PTV top board.

With the Billboard shifted toward the PTV Screen, insert the base plate of the Billboard into the 2 mask holders of the PTV Top Board.

Use a step for the following works:

Using the 2 truss screws, secure the Billboard to the PTV Top Board.

® Remove the 2 truss screws. Then, remove the Hole Lid from the Billboard.

Connect the 2 connectors in the Billboard to the 2 connectors on the PTV top board. The connectors can be inserted only in the fixed orientation. If you attempt to apply constrained force when inserting the connector, it may break. Fully make sure that it is in the correct orientation.

(Reinstall the Hole Lid to the initial position by securing it with the 2 truss screws.

Page 25

TRUSS SCREW (2) \ M5 X 40, chrome plated

BILLBOARD

TRUSS SCREW (2)

M4 X 8, chrome plated

Connect the 2 Connectors.

FIG. 6. 1d

When performing work, For performing work, use 2 workers. be sure to use a step.

FIG. 6. le FIG. 6.1 f

Page 26

2 WIRING CONNECTIONS BETWEEN THE CABINETS

With the ASSY Tube installed to the Front and Rear Cabinets, perform the cabinet-to-cabinet wiring. The connectors can be inserted only into those with the same number of pins, respectively, and can be inserted only in the fixed orientation. If you attempt to apply constrained force when inserting the connector, the connector or wiring may be damaged. Fully make sure that it is in the correct orientation.

® Draw out the 6 wiring connectors and the earth wire from the Front Cabinet.

Connect the connector of the ASSY Tube and that of the Front Cabinet. Connect the connectors to those with the same number of pins, respectively.

Connect the Connector, f

@The plate of the ASSY Tube has a stud used to secure the earth wire. Let the earth wire round terminal, flat washer, and spring washer pass through the stud in order. Then tighten the hexagon nut. PHOTO 6. 2a

HEXAGON NUT (1) M4, flat & spring washers used.

PHOTO 6.2b

Page 27

® Install the plate of the ASSY Tube

to the front of the Front Cabinet by using the 4 truss screws. Do not pinch the wiring at this time.

TRUSS SCREW (4), black, PHOTO 6.2 ¢ M4 X 20

® Locate the Front and Rear Cabinets close to each other. If you jerk the wiring by applying constrained force (in order to connect the connectors), the wiring may be damaged.

@©Draw out the 6 wiring connectors from the Rear Cabinet.

@ Connect the connector of the ASSY Tube and that of the Rear Cabinet. Connect the connectors to those with the same number of pins, respectively.

Connect the Connector.

PHOTO 6. 2d

Install the plate of the ASSY Tube to the Rear Cabinet. Use the 4 screws for securing. Be careful not to pinch the wiring.

SCREW (4), black M4 X 10, w/flat & spring washers

20 PHOTO 6.2¢

Page 28

J

WARNING!

SECURING IN PLACE (ADJUSTER ADJUSTMENT)

cabinet can move and cause an accident. Make sure that all of the adjusters are in contact with the floor. If they are not, the

This machine has 8 casters (4 for the Front Cabinet, 4 for the Rear Cabinet) and 8 adjusters (4 for the Front Cabinet, 4 for the Rear Cabinet). (FIG. 6.3 a) When the installation position is determined, cause the adjusters to come into contact with the floor directly, make adjustments in a manner so that the casters will be raised approximately 5mm. from the floor and make sure that the machine position is level.

® Move the machine to the installation

position. To ensure the safe operation of the product, provide sufficient space by adequately keeping the product away from wall surfaces and other cabinets.

Cause all of the adjusters to make contact with the floor. By using a wrench, make adjustments in the height of the adjusters to ensure that the machine's position is level.

After making adjustments, fasten the adjuster nut upward and secure the

height of the adjuster. (FIG. 6. 3 b)

ADJUSTER (10 in total)

ADJUSTER a Le

ace

FIG. 6.3¢ Refer to this Fig. (Scale: 1/100) for the layout of the place of installation. FASTEN UPWARI CASTER (8 in total)

FIG. 6.3 a BOTTOM VIEW

CASTER

Approx.5mm. \ apiusTER

10cm FIG. 6.3 b ADJUSTER

FIG. 6.3d Es rs 7. ie LMM SU 14cm Provide sufficient space so as to allow for ventilation by the ventilation fan. Provide space approximately 14cm. between the Front Cabinet and the Rear Cabinet.

Page 29

Z INTALLING THE SIDE POP

View from above

First, fold along the crease lines, with the text facing the outside.

LE ft Crease lines

Peel off the tape on section @ and affix the card to

the side of the PTV. Insert the PTV side-screw into the hole in section (4) and tighten.

i oy

Peel off the tape on section (8), then affix it to the blank side of section (1). FIG. 6.4

Page 30

5 POWER SUPPLY, AND EARTH CONNECTION

Earth Leakage Breaker. Using a power supply without an Earth Leakage Breaker can cause a fire when electric leakage occurs. @ Ensure that the "accurately grounded indoor earth terminal" and the earth wire cable are available (except in the case where a power cord plug with earth is used). This product is equipped with the earth terminal. Connect the earth terminal and the indoor earth terminal with the prepared cable. If the grounding work is not performed appropriately, customers can be subjected to an electric shock, and the product's functioning may not be stable. Ensure that the power cord and earth wire are not exposed on the surface (passage, etc.). If exposed, they can be caught and are susceptible to damage. If damaged, the cord and wire can cause electric shock and short circuit accidents. Ensure that the wiring position is not in the customer's passage way or the wiring has protective covering. After wiring power cord on the floor, be sure to protect the power cord. Exposed power cord is susceptible to damage and causes an electric shock accident.

A @ Be sure to independently use the power supply socket outlet equipped with an

WARNING!

The AC Unit is mounted on the side of the machine. The AC Unit has Main SW, Circuit Protector and the Inlet which connects the Power Cord.

® Ensure that the Main SW is OFF.

MAIN SW

CIRCUIT PROTECTOR el a ® i ° °

SS 1 Ole2 @o °o @ = S Kj) o@ °

® ®

Main SW off

\ INLET = \ EARTH TERMINAL

i Connect with the

indoor earth terminal. AC Cable (Power Cord) Spe

FIG. 6. 5a AC unit

Page 31

Connect the Earth Wire to the Earth Terminal.

@ Connect one end of the earth wire to the AC

Unit earth terminal, and the other end to the indoor earth terminal. The AC Unit earth terminal has a Bolt and Nut combination.

Take off the Nut, pass the end of earth wire

through the Bolt, and fasten the Nut.

Note that the Earth Wire is incorporated in the Power Cord for the Areas of AC 120V (USA) and AC 220 ~ 240V, and therefore, this procedure is not necessary. FIG. 6. 5b Earth Wire Connection

@® Firmly insert the power plug into

the socket outlet. Insert the opposite side of Power Cord plug to the AC Unit's connector ("INLET").

@ Perform wiring for the Power Cord

and Earth Wire. Install protective covering for the Power Cord and Earth Wire.

FIG. 6. 5c Connecting Power Cord and Earth Wire

In case the Power Plug is apt to come out of place, secure the Power Cord to the periphery of the AC Unit with the Cord Clamp (an accessory).

HOW TO USE THE CORD CLAMP

Page 32

TURNING POWER ON

Turn on the AC unit main switch to power on the machine. Once it is powered on, the Billboard fluorescent lamp and Slim Tube light up. After several seconds, the screen changes to the Advertise Screen, which is in the wait-for-guest mode. At the same time, the loudspeakers to the left and right of the Switch Panel and the super woofer located at the bottom of the cache box door output voices. If No Voice Output has been set, no voices are output during the Advertise Mode. The four Cold-Cathode Tubes to the left and right of the Rear Cabinet light up or go out, depending on the status on the Advertise Screen. Even after being powered off, this product retains data about the number of credits and ranking. It does not retain the Factional Number of Coins (i.e., the number of coins put into the slot does not reach one credit) or Bonus Adder Count data. Thus, if you power on the machine after powering it off when the available number of credits for playing a game has remained, powering on machine causes the Start button to blink. The Skateboard is unlocked when a game starts. Thus, it cannot be moved to the left or right unless a coin is put into the slot and the Start button is pressed.

Billboard's fluorescent lamp and Slim lamp Always lit

On-screen images are outputted,

Start button,

Sound is emitted. _

| Cold-Cathode Tube On/Off

FIG. 6. 6

Page 33

7 ASSEMBLING CHECK

In the TEST MODE, ensure that the assembly has been made correctly and IC BD. is satisfactory (refer to Section 9). In the test mode, perform the following test:

  • MEMORY TEST

RAM TEST

IC15 IC16 IC17SIC18S GOOD 1C22 IC23 IC24S IC25S GOOD IC28 IC29S GOOD IC41 GOOD 1C42 GOOD 1C44 IC45S IC46 IC47S GOOD IC91S IC92S GOOD IC98 GOOD

OPTIONAL SOUND BOARD: 1c2 GOOD

PRESS TEST BUTTON TO EXIT

  • SOUND TEST

SOUND TEST MAIN SPEAKER LEFT MAIN SPEAKER RIGHT > EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON Selecting the RAM TEST on the System Test Mode menu screen causes the on-board memory to be tested automatically. The game board is satisfactory if the display beside each IC No. shows GOOD.

On the Menu screen in the System Test Mode, selecting SOUND TEST causes the screen (on which sound related BD and wiring connections are tested) to be displayed. Be sure to check if the sound is satisfactorily emitted from each speaker and the sound volume is appropriate.

Page 34
  • C.R.T. TEST

In the System Test Mode menu, selecting C.R.T. TEST allows the screen (on which the projector is tested) to be displayed. Although the projector adjustments have been made at the time of shipment from the factory, make judgment as to whether an adjustment is needed by watching the test mode screen. If it is necessary, adjust the projector by referring to Section 11.

C.R.T. TEST PAGE#1

RED C.R.T. TEST PAGE#2

GREEN

BLUE

WHITE

PRESS SERVICE BUTTON TO ANOTHER PAGE PRESS TEST BUTTON TO EXIT PRESS SERVICE BUTTON TO ANOTHER PAGEL. PRESS TEST BUTTON TO EXIT. io

  • INPUT TEST

INPUT TEST NODE V/1 BUTTON START OFF LEFT OFF RIGHT OFF UP OFF DOWN OFF SERVICE OFF TEST OFF VOLUME YAW 80

ROLL 80

PRESS TEST AND SERVICE BUTTON TO EXIT Selecting the INPUT TEST on the Game Test Mode menu screen causes the screen (on which each switch is tested) to be displayed. Press each switch. If the display beside each switch indicates "ON," the switch and wiring connections are satisfactory.

  • OUTPUT TEST

OUTPUT TEST

LEFT UPEER LAMP OFF LEFT LOWER LAMP OFF RIGHT UPEER LAMP OFF RIGHT LOWER LAMP OFF START LAMP OFF LOCK MECHA OFF > EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON The OUTPUT Test menu screen in the Game Test Mode allows Lamps and wiring connections to be checked. Check if each lamp lights up satisfactorily.

Perform the above inspections also at the time of monthly inspections.

Page 35
  • PRECAUTIONS TO BE HEEDED WHEN MOVING THE MACHINE

machine with the plug as is inserted can damage the power cord and cause fire

WARNING! and electric shock hazards. " When moving the machine on the floor, retract the Adjusters and ensure that Casters make contact with the floor. During transportation, pay careful attention so that Casters do not tread power cords and earth wires. Damaging the power cords can cause electric shock and short circuit hazards. When lifting the cabinet, be sure to hold the grip portions or bottom part. Lifting the cabinet by holding other portions can damage parts and installation portions due to the empty weight of the cabinet, and cause personal injury. en transporting the product in places with step-like differences in grade, isassemble into each unit before transporting. Lifting up the product in an attempt to cross the step-like differences in an as is assembled condition may

lamage the unit's joining portions and cause a personal injury resulting from

lamage. When moving the PTV, do not push it from the rear side. Push it from sideways. Pushing the PTV from the rear side can have the PTV fall down, causing personal injury etc. In case the floor has slanted surfaces or step-like ifferences, be sure to move the machine by 2 or more persons. Do not insert the fork to places other than designated when using a Forklift to transport the machine. Failure to observe this could cause falling down and injury resulting from falling down.

A\ S 2 2 2 Failure to observe this may damage parts and caus' Iting from damage.

CAUTION!

A @ When moving the machine, be sure to unplug the power plug. Moving the

S @ When transporting the product in places with steps, disassemble into each unit

before transporting. Inclining the product in an as is assembled condition or

INPORTANT placing the cabinet in places with steps can damage the unit's joining portions. : @ To protect surface, do not directly apply a rope to the surfaces of product. Use protective materials to the places the rope is applied to.

e Do not push PTV from the back. Pushing the PTV from the can cause the PTV to fall down. Push it from the side.

Page 36

On level surfaces, move the machine by causing the Casters to make contact with the surfaces.

FIG. 7a

f When transporting the product in places

with steps or step-like differences in grade, disassemble into each unit before transporting.

GRIP

FIG. 7b

Page 37

The pop is apt to break, and pay attention to it.

Hold the grip to move.

Plastic made parts

FIG.7¢

Page 38
  • CONTENTS OF GAME

The following explanations apply to the case the product is functioning satisfactorily. Should there be any moves different from the following contents, some sort of faults may have occurred. Immediately look into the cause of the fault and eliminate the cause thereof to ensure satisfactory operation.

While the machine is being energized, the Billboard's fluorescent lamp and Slim Tube continuously stay lit up. The left and right Rear Cabinets light up or go out, depending on the status on the Advertise Screen. The screen displays demonstration video images and ranking data. The loudspeakers to the left and right of the Switch Panel and the super woofer located at the bottom of the cache box door output voices. With the settings in the Test Mode, you can select whether to output voices in the Advertise Mode.

Billboard's fluorescent lamp and Slim lamp Always lit

On-screen images are outputted.

Start button,

Sound is emitted.

Skateboard Lock,

\\ Cold-Cathode Tube On/Off

FIG. 8b

Page 39

The on-screen ADVERTISE before the commencement of game is comprised of the following:

DESCRIPTION OF SEGA ROGO }—-» ADVERTISE |—> TITLE [| OPERATION t [| RANKING

FIG. 8b

TITLE ADVERTISE DESCRIPTION OF OPERATION

The Skateboard is unlocked before the game starts. Thus, it cannot be moved to the left or right unless a coin is put into the slot and the Start button is pressed.

How to Play

® Get on the Skateboard (i.e., Controller Board).

@ The Coin Tower is located in the center of the enclosure. Once coins for one play session are put in the slot, the Start button lamp blinks. Pressing the Start button displays the Select Player Screen. Once it appears, credit display stops.

® On the Select Player Screen, select the

desired character for play. Using the Select button, select the desired one from the five characters. Then, determine it using the Start button. Select the character using the left and right Select buttons. Determine it using the Start button, located in the center. The numbers at the top right corner of the screen indicate the time START BUTTON limit for selection. OO The characters have both advantageous and disadvantageous FIG. 8 ¢ characteristics about their running performance. SELECT BUTTON

(O) Once you determine the player, you are brought to the Select Stage Screen. Using the Select button, select the desired one from the three stages. Then, determine it using the Start button. There are two stage modes: Tutorial and Score Attack. One stage is available for the Tutorial Mode, and two stages are available for Score Attack Modes.

© Tutorial Mode (left) Lets the player learn three ways of triggering elementary tricks.

O Score Attack Mode (center, right)

Allows the player to trigger tricks and compete for the number of coins acquired.

Page 40

@®while the Select Player or Stage Screen is on-screen, the remaining time for selection is displayed at the top right corner of the screen. If the player does not press the Start button within the time, the system will automatically regard the currently selected character and stage as the finally determined ones.

FIG. 8 d Player Select screen, Stage Select screen

© Once the stage is determined, the game starts. After message "Release the lock of the controller board" appears, the Skateboard (i.e., Controller Board) is unlocked. Then, the player can perform Spin operations. At the bottom, turn in the desired direction in the manner of skateboarding. Further, the player can enjoy a sharper turn by spinning the board.

Backward and forward inputting Curving (inclining) Input FIG. 8e

Page 41

At the bottom, turn in the desired direction in the manner of skateboarding. Further, the player can enjoy a sharper turn by spinning the board.

Lip

Ramp

Bottom

FIG. 8 f£

@The aim of this game is to get a high score by achieving a trick in the air. The player can achieve a trick by inputting data to the Controller Board on the lip.

A trick appears -- Acceleration ee Totters -- Lose Speed

\ & Succeed in kicking \e w Fail in kicking

In addition, the player can achieve tricks separately by inputting different types of data during kicking. FIG.8 g

Page 42

"Achieving a COMBO Trick" The player can cause a COMBO trick by kicking on the back of the Controller Board at the front of the lip. Once the player can succeed in the kicking, he or she can link the tricks by reinputting the data in the air. The knack of acquiring proficiency is to input data moderately to the Controller Board, taking account into the his or her speed (i.e., duration of jump). If the player inputs the first item of data after the jumping step is exceeded, the character loses its speed. The advice is displayed at this time.

"How to Achieve a Spinning Trick" The player can generate a spinning trick by spinning the Controller Board at the front of the lip. Once the player succeeds in the kicking, keeping the position achieved at the time of kicking in the air causes the character to start spinning. A longer time of spinning results in a higher score; however, if the player continues to keep the position at landing time, the character will fall down. If the player inputs the first item of data after the jumping step is exceeded, the character loses its speed. The advice is displayed at this time.

"Achieving a Grind Trick" The player can generate a grind trick by diagonally entering the bottom and kicking on the front of the Controller Board at the front of the lip. Once the player succeeds in the kicking, keeping the position achieved at the time of kicking in the air causes the character to start skating on the lip. A longer time of skating results in a higher score; however, the character falls down unless the player restores the board before it totters. If the player inputs the first item of data after the jumping step is exceeded, the character loses its speed. The advice is displayed at this time.

Page 43

® The fields on the screen are as follows while the game is in progress:

£ ee ene i= . o= 13Q160coIns

(CSRINTRICK7 OOD<—_ 2 1096

71°C (COOL i 70 BONES <<c——__ <= 1GOINS ¥ +i + v i D+ ——_ > TAIL GRAB

FIG. 8k

1: Number of Coins Acquired Displays the current number of coins acquired, and the number of coins that must be acquired until the next grade. 2: Bonus Title The bonus coins can be acquired by clearing the contents of the title while a play is in progress. The contents vary each time the character grades up. 3: Trick Displays the category and the contents of the currently achieved trick. 4: Evaluation per Jump Displays the grade that corresponds to the total number of coins acquired per jump by grade. This grade has no relation to that on the top left corner of the screen. 5: Trick Name Displays the name of the sill achieved. 6: Grade Displays the current grade, which will rise when coins will be acquired. 7: Coins Acquired Displays the current number of coins acquired, and the number of coins that must be acquired until the next grade. 8: Remaining Time Remaining time within the stage. When it reaches 0, the stage ends. 9: Evaluation of Kicking Appears when the timing of kicking is good. 10: Cool COMBO Bonus When COMBO tricks are in progress, this may appear if combined tricks are cool.

Page 44

when the time expires, the game is over. @atier the game ends, lock the Skateboard (i.e., Controller Board).

If the player establishes a high score, the final evaluation will be followed by a screen letting him or her enter the three initials. In response to the prompt, the player should select the characters while scrolling them with the Select button. Then, determine the characters one by one using the Start button. Once all the three are determined, the player should locate the cursor at END and press the Start button for determination.

On the Score Attack Mode, the password appears along with the Game Over display. Record this password. The player can be registered for the World Ranking by sending it to the home page of this game. Using the Start button, the player can skip this screen, which remains on-screen for several tens of seconds. Home page address: http://www.hitmaker.co.jp/AIRTRIX By making the settings in the Test Mode, you can select whether to display the password.

Page 45

9, EXPLANATION OF TEST AND DATA DISPLAY

By operating the switch unit, periodically perform the tests and data check. When installing the machine initially or collecting cash, or when the machine does not function correctly, perform checking in accordance with the explanations given in this section. The following shows tests and modes that should be utilized as applicable.

SEGA HIKARU GAME BOARD is used for the product. The system of this game board

allows another game to be played by replacing the ROM Board Case mounted on the SEGA. HIKARU CASE. As such, the Test Mode of this system consists of the System Test Mode for the system to execute SELF-TEST, COIN ASSIGNMENTS, ete. used in common for the machines employing the SEGA HIKARU BOARD, and the Game Test Mode for the specific product to execute Input/Output test for the operation equipment, difficulty setting, etc.

mode is finished from EXIT in the menu mode. If the power is turned off

before the TEST mode is finished, the contents of setting change become

IMPORTANT ineffective.

S @ The contents of settings changed in the TEST mode are stored when the test

Executing "BACKUP DATA CLEAR" in the SYSTEM TEST MODE does not clear the BOOKKEEPING data in the GAME TEST mode.

Entering the TEST mode clears fractional number of coins less than one credit

and BONUS ADDER data.

TABLE 9 EXPLANATION OF TEST MODE

ITEMS DESCRIPTION ene”

INSTALLATION OF | When the machine is installed, perform the following: 9-2 F.G,9-3D MACHINE 1. Check to see that each setting is as per standard setting made at the ~ time of shipment. 9.2C,9-3B

  • In the INPUT TEST mode, check such input devices as each SW, > V.R., etc. 93C
  • In the OUTPUT TEST mode, check such output devices as lamps, motors, etc. 9-2BJ
  • In the SELF-TEST mode, check ICs on the IC Board. *

MEMORY Choose RAM TEST and ROMBD TEST in the MENU mode to allow | 9 5 py the MEMORY test to be performed. In this test, PROGRAM RAMs, * ROMs, and ICs on the IC Board are checked.

PERIODICPeriodically perform the following:92BJ
SERVICING1. MEMORY TEST9-2F.G,9-3D
  • Ascertain each setting. 9.2C.93B
  • In the INPUT TEST mode, test the CONTROL device 93 Cc -
  • In the OUTPUT TEST mode, check such output devices as lamps, motors, etc.
CONTROL1. In the INPUT TEST mode, check such input devices as each SW,9.2C.9-3B

SYSTEM V.R., ete. ’

  • Adjust or replace each SW and VR. 9-3 F. 10
  • If the problem can not be solved yet, check the CONTROL's , moves.
MONITORIn the MONITOR ADJUSTMENT mode,02E

check to see if the PROJECTOR adjustment is appropriately made. D

IC BOARD1. MEMORY TEST92BJ
  • In the SOUND TEST mode, check the sound related ROMs. 9.2 D
DATA CHECKCheck such data as game play time and histogram to adjust the9-2H,9-3E

difficulty level, etc.

Page 46

9-1 SWITCH UNIT AND COIN METER

Never touch places other than those specified. Touching places not specified can cause electric shock and short circuit hazards.

WARNING!

Gr0%) @ Adjust to the optimum sound volume by considering the environmental

requirements of the installation location. @ [fthe COIN METER and the game board are electrically disconnected, game play is not possible.

IMPORTANT

SWITCH UNIT _—SOURD VOLUME \\ For Super Woofer Open the coin chute door, and the switch unit shown will appear. The functioning of each SW is as follows: TEST BUTTON

SERVICE BUTTON

SOUND VOLUME _ “ae For Right/Left Speakers. SUPER

SPEAKER WOOFER TEST SERVICE

FIG. 9. 1a SWITCH UNIT

SOUND VOLUME CONTROL : Adjusts the Right/Left Speakers. SPEAKER SOUND VOLUME CONTROL : Adjusts the Super Woofer . SUPER WOOFER

TEST BUTTON : For the handling of the test button, refer to

TEST the following pages. SERVICE BUTTON : Gives credits without registering on the coin SERVICE meter.

COIN METER

Open the Cashbox Door by using the key to have the Coin Meter appear underneath the Cashbox.

COIN METER

FIG. 9. 1b

Page 47

9-2 SYSTEM TEST MODE

A. SYSTEM TEST MODE MENU

Press TEST Button to enter the TEST MODE, and the following Menu screen will be displayed.

@ Press SERVICE Button to move the arrow (>) to the desired item and select with TEST Button. SYSTEM MENU XXXXXXXXX VERSION

RAM TEST JVS TES . SOUND TEST @ Bring the arrow to EXIT and press C.R.T. TEST TEST Button to return to the GAME SYSTEM ASSIGNMENTS, Mode. COIN ASSIGNMENTS BOOKKEEPING BACKUP DATA CLEAR ROMBD TEST CLOCK SETTING GAME TEST MODE > EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

B. RAM TEST

This allows for checking the functioning of the RAM on the Game BD. In this test, IC's are checked in every row. During the test, "CHECKING" is displayed at the right-hand side of the screen. "BAD" is indicated for irregular RAMs, if any. Upon finishing the test, "PRESS TEST BUTTON TO EXIT" is displayed on the lower center of the monitor. Press TEST Button to return to the MENU screen.

RAM TEST

IC15 IC16 IC17SIC18S GOOD 1C22 IC23 IC24S IC25S GOOD 1C28 IC29S GOOD IC41 GOOD 1C42 GOOD 1C44 IC45S IC46 IC47S GOOD IC91S IC92S GOOD IC98 GOOD

OPTIONAL SOUND BOARD: IC2 GOOD

PRESS TEST BUTTON TO EXIT

Page 48

C. JVS TEST

JVS TEST INPUT TEST > EXIT

NODE V/1 NAME SEGA ENTERPRISES,LTD.;I/O BD JVS; 837-13551 ;Verl.00;98/10 CMD VER 1.1 JVS VER 2.0 COM VER 1.0 SWITCH 2 PLAYERS 13BITS COIN 2 SLOTS ANALOG 8CH DRIVER OUT 6CH

SELECT WITH SERVICE BUTTON AND PRESS ST BUTTON In this test, Functioning of the I/O Board connected to Game Board is displayed and INPUT TEST can be performed. Execute EXIT to return to the MENU

screen.

When INPUT TEST is selected and executed, the following screen appears.

JVS TEST > DISPLAY CONFIG EXIT

NODE 1/1 SWITCH SYSTEM PLAYERI PLAYER2 COIN SLOT1 0000 SLOT2 8000 ANALOG CHI 6300 CH2 5A00 CH3 7D00 CH4 8100 CHS5 1F00 CH6 1D00 CH7 1F00 CH8 2000

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON When INPUT is performed, the Switch value changes to 1 from _.

Execute EXIT to return to the MENU screen.

Page 49

D. SOUND TEST

Sound Output can be performed and each Speaker can be checked.

SOUND TEST MAIN SPEAKER LEFT MAIN SPEAKER RIGHT > EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

E. C.R.T. TEST Select the desired item and press TEST Button, and sound is emitted from the corresponding Speaker. Execute EXIT to return to the MENU screen.

In this test, monitor adjustment can be performed. Periodically check to see if the monitor adjustment is appropriate in this test. This test consists of 2 screens. Use SERVICE Button to change the screen displayed. Press TEST Button to return to the MENU screen.

C.R.T. TEST PAGE#1

RED

GREEN

BLUE

WHITE

PRESS SERVICE BUTTON TO ANOTHER PAGE PRESS TEST BUTTON TO EXIT.

RESS SERVICE BUTTON TO ANOTHER PAGE} PRESS TEST BUTTON TO EXIT The first screen displays color bars. The color adjustment can be checked. Each

of red, green, blue is the darkest at the

leftmost end, and becomes brighter towards the right-hand end.

The second screen displays crosshatches. In this page, monitor size and deviation can be checked.

Page 50

F. SYSTEM ASSIGNMENTS

The settings of cabinet and board can be changed. Set each item suitable to the connected cabinet. Use the setting as is the time of shipment except for ADVERTISE SOUND.

SYSTEM ASSIGNMENTS,

CABINET TYPE IPLAYER ADVERTISE SOUND ON MONITOR TYPE HORIZONTAL DISPLAY MODE AUTOSCAN SERVICE TYPE COMMON

> EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

© CABINET TYPE specifies Control Panel and number of Coin Chute. The number of Player displayed in BOOKKEEPING varies in accordance with the value here.

© ADVERTISE SOUND is used for settings of emitting sound during ADVERTISE.

© MONITOR TYPE sets the on-screen display to the positional direction of monitor (HORI- ZONTAL or VERTICAL). If set to VERTICAL, the on-screen display for the test mode is vertically positioned in accordance with the setting.

© DISPLAY MODE sets the monitor's display frequency. In this mode, if other than AUTOSCAN is selected and EXIT is executed, the display frequency is changed to the selected setting.

© SERVICE TYPE sets the functioning of when the Service Button is pressed, in case that several Service Buttons exist.

*« INDIVIDUAL By pressing Service Button, Service credit can be obtained for the Player corresponding to the Service Button pressed.

  • COMMON By pressing any Service Button, Service credit can be obtained for all Players.
Page 51

G. COIN ASSIGNMENTS

In this mode, the setting of incremental credit increase as against coin insertion can be changed. This test consists of 3 screens, and the following is the first screen. The setting done in the first screen will be stored when exited.

COIN ASSIGNMENTS. COIN CHUTE TYPE COMMON COIN/CREDIT SETTING #1 COIN CHUTE #1 1COIN 1CREDIT

COIN CHUTE #2 1COIN 1CREDIT

MANUAL SETTING SEQUENCE SETTING > EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

© COIN CHUTE TYPE sets whether Coin Chute is used in common by all players or separately allocated to each player in case 2 or more Coin Chutes are incorporated. COMMON: This setting is for common use by plural players. INDIVIDUAL: As each player uses an independent coin chute, setting to INDIVIDUAL causes COIN CHUTE #2 to be disappeared.

© COIN/CREDT SETTING is set when using one of the existing 26 settings or FREE PLAY. The selected coin rates in the COIN/CREDIT SETTING are displayed below COIN CHUTE #1 and COIN CHUTE #2. If you wish to set a coin rate rather than to select from the existing setting, select MANUAL SETTING. The display next to COIN/CREDIT SETTING indicates "MANUAL", not "#n" in this case.

  • This game does not use SEQUENCE SETTING. Do not change the SEQUENCE SETTING data.
Page 52

© MANUAL SETTING

When MANUAL SETTING is selected in the first screen, the following second screen appears.

COIN ASSIGNMENTS MANUAL SETTING

COIN TO CREDIT 1 BONUS ADDER 0 COIN CHUTE #1 MULTIPLIER 1 COINCOUNT AS_— 1COIN COIN 123456789 CREDIT 123456789

COIN CHUTE #2 MULTIPLIER 1 COINCOUNT AS_— 1COIN COIN 123456789 CREDIT 123456789

SEQUENCE SETTING > EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

© COIN TO CREDIT determines how many coins are needed for one credit. (1 ~ 9)

© BONUS ADDER determines how many coins should be inserted to obtain one SERVICE COIN.

© COIN CHUTE #1 MULTIPLIER, COIN CHUTE #2 MULTIPLIER sets how many tokens one Coin represents inserted in each COIN CHUTE.

SETTING EXAMPLE 1)

Setting of 2 COINS 1 CREDIT, set to:

COIN TO CREDIT 2 BONUS ADDER 0 COIN CHUTE #1 MULTIPLIER :1

SETTING EXAMPLE 2)

Setting of 5 COINS 6 CREDITS (5 COINS 1 BONUS), set to

COIN TO CREDIT il BONUS ADDER 5 COIN CHUTE #1 MULTIPLIER :1

When exiting from MANUAL SETTING, if the identical coin rate is in the existing COIN/ CREDIT SETTING, such existing mode other than what is set in the MANUAL SETTING is confirmed.

Page 53

TABLE 1 COIN/CREDIT SETTING

NAME OF SETTING FUNCTIONING OF COIN CHUTE #1 FUNCTIONING OF COIN CHUTE #2

SETTING #1 1 _ COIN1 CREDIT1 COIN1_ CREDIT
SETTING #2 1_ COIN2_ CREDITS1 COIN1 CREDIT
SETTING #3 1_ COIN3_ CREDITS1 COIN1_ CREDIT
SETTING #4 1 COIN4 CREDITS1 COIN1 CREDIT
SETTING #5 1 COIN5 CREDITS1 COIN1_ CREDIT
SETTING #6 1 COIN2_ CREDITS1 COIN2_ CREDITS
SETTING #7 1 COIN5 CREDITS1 COIN2_ CREDITS
SETTING #8 1 COIN3__ CREDITS1 COIN3__CREDITS
SETTING #9 1 COIN4 CREDITS1 COIN4 CREDITS
SETTING #10 1_ COIN5 CREDITS1 COIN5 CREDITS
SETTING #11 1 COIN6 CREDITS1 COIN6 CREDITS

SETTING #12 2__COINS 1 CREDIT 2__ COINS 1 CREDIT

SETTING #13 1_COIN1 CREDIT2 COINS 1 CREDIT
SETTING #14 1 COIN2 CREDITS2 COINS 1 CREDIT
SETTING #15 1 COIN1 CREDIT1 COIN1 CREDIT

2_ COINS 3__ CREDITS 2 COINS 3__ CREDITS

SETTING #16 1 COIN3. CREDITS1 COIN1 CREDIT

2 COINS 3__CREDITS

SETTING #17 3 COINS 1 CREDIT 3 COINS 1_ CREDIT

SETTING #18 4 COINS 1 CREDIT 4 COINS 1 CREDIT

SETTING #19 1 COIN1 CREDIT1 COIN1 CREDIT

2 COINS 2 CREDITS 2 COINS 2 CREDITS

3 COINS 3. CREDITS 3 COINS 3. CREDITS

4 COINS 5 CREDITS 4 COINS 5_CREDITS

SETTING #20 1 COIN5 CREDITS1 COIN1 CREDIT

2 COINS 2 CREDITS

3 COINS 3. CREDITS

4 COINS 5_CREDITS

SETTING #21 5 COINS 1 CREDIT 5__COINS 1_CREDIT

SETTING #22 1 COIN2 CREDITS3 COINS 1 CREDIT

5_COINS 2 CREDITS

SETTING #23 2 COINS 1 CREDIT 2 COINS 1 CREDIT

4 COINS 2 CREDITS 4 COINS 2 CREDITS

5__COINS 3__ CREDITS 5 COINS 3__CREDITS

SETTING #24 1 COIN3. CREDITS2 COINS 1 CREDIT

4 COINS 2 CREDITS

5_COINS 3 CREDITS

SETTING #25 1 COIN1 CREDIT1 COIN1 CREDIT

2 COINS 2 CREDITS 2 COINS 2 CREDITS

3 COINS 3. CREDITS 3 COINS 3. CREDITS

4 COINS 4 CREDITS 4 COINS 4 CREDITS

5_COINS 6 CREDITS 5_COINS 6 CREDITS

SETTING #26 1 COIN6 CREDITS1 COIN1 CREDIT

2 COINS 2 CREDITS

  • COINS 3. CREDITS

4 COINS 4 CREDITS

5__COINS 6 CREDITS

SETTING #27 FREE PLAY FREE PLAY

Page 54

Table 2: COIN/CREDIT SETTING (COIN CHUTE INDIVIDUAL TYPE)

NAME OF SETTING] EACH SEAT'S COIN CHUTE NAME OF SETTING] EACH SEAT'S COIN CHUTE

SETTING #11COIN _ 1 CREDITSETTING #21S COINS_1 CREDIT
SETTING #21COIN2 CREDITSSETTING #232COINS1 CREDIT
SETTING #31COIN3 CREDITS4COINS2 CREDITS
SETTING #41COIN4 CREDITS5 COINS3 CREDITS
SETTING #51COIN5 CREDITSSETTING #251COIN1 CREDIT
SETTING #111COIN6 CREDITS2COINS2 CREDITS
SETTING #122 COINS_1 CREDIT3 COINS3 CREDITS
SETTING #151COIN1 CREDIT4COINS4CREDITS
2 COINS3 CREDITSS COINS6 CREDITS
SETTING #173 COINS_1 CREDITSETTING #27FREE PLAY
SETTING #184COINS1 CREDIT
SETTING #191COIN1 CREDIT

2COINS 2 CREDITS 3 COINS 3 CREDITS 4COINS _5 CREDITS

Table 3: MANUAL SETTING

COIN TO CREDIT1COIN1 CREDIT
2COINS1 CREDIT
3.COINS1 CREDIT
4COINS1 CREDIT
5COINS1 CREDIT
6COINS1 CREDIT

7__COINS 1 CREDIT

8COINS1 CREDIT
9COINS1 CREDIT

BONUS ADDER NO BONUS ADDER

2COINS GIVE1 EXTRA COIN
3COINS GIVE1 EXTRA COIN
4COINS GIVE1 EXTRA COIN
5COINS GIVE1 EXTRA COIN
6COINS GIVE1 EXTRA COIN
7COINS GIVE1 EXTRA COIN
8COINS GIVE1 EXTRA COIN
9COINS GIVE1 EXTRA COIN
COIN CHUTE (#1 / #2) MULTIPLIER1COIN COUNTS AS1 COIN
1COIN COUNTS AS2 COINS
1COIN COUNTS AS3 COINS
1COIN COUNTS AS4 COINS
1COIN COUNTS AS5 COINS
1COIN COUNTS AS6 COINS
1COIN COUNTS AS7 COINS
1COIN COUNTS AS8 COINS
1COIN COUNTS AS9 COINS
Page 55

This game does not use SEQUENCE SETTIN

Do not change the SEQUENCE SETTING

IMPORTANT

© SEQUENCE SETTING

When SEQUENCE SETTING is selected in either first or second screen, the SEQUENCE SETTING Mode (the third screen) appears. In this mode, number of credits required for starting game can be set.

COIN ASSIGNMENTS SEQUENCE SETTING

SEQUENCE1 *CREDIT SEQUENCE2 *CREDIT SEQUENCE3 *CREDIT SEQUENCE4 *CREDIT SEQUENCES *CREDIT SEQUENCE6 *CREDIT SEQUENCE7 *CREDIT SEQUENCE8 *CREDIT > EXIT

[ XXXXXXXXXXXXXXXXXXXX] [ SEGA ENTERPRISES,LTD. ] DESCRIPTION OF SEQUENCE SEQ] #6 SEQ? #16 SEQ3 #16 SEQ4 #16 SEQS #14 SEQ6 SEQ7 #16 SEQS #6

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

Each sequence can be set between | ~ 5 Select EXIT to return to the first screen.

Page 56

H. BOOKKEEPING

This allows such data as operating time/No. of coins inserted/ No. of credits to be checked, etc. This test consists of 2 screens. Pressing SERVICE Button causes screen to be changed. Press TEST Button to return to the MENU screen. On the first screen, such data as total time, coin, and credit are displayed.

BOOKKEEPING

TOTAL TIME 55H27M13S

COIN1 16 SERVICE1 5 COIN2 4 SERVICE2 0

CREDIT 10

TOTAL COIN 20 COIN CREDIT 10 SERVICE CREDIT 5 TOTAL CREDIT 15

PRESS SERVICE BUTTON TO ANOTHER PAGE PRESS TEST BUTTON TO EXIT

© Total Time is displayed as "X X H X X M X XS" and no date will be displayed after exceeding 24 hours.

© The displays for number of coin and number of service vary depending on the CABINET TYPE set in SYSTEM ASSIGNMENTS.

Number of credit displays 1 if COIN CHUTE TYPE is set to COMMON in COIN

ASSIGNMENTS. If COIN CHUTE TYPE is set to INDIVIDUAL, the applicable number in CABINET TYPE setting will be displayed.

On the second screen, each sequence displays the frequency of functioning.

BOOKKEEPING

PLAYERI PLAYER2

SEQI1SEQI0
SEQ20 SEQ21
SEQ31SEQ30
SEQ40 SEQ41
SEQS0 SEQS0
SEQ60 SEQ60
SEQ70 SEQ70
SEQ80 SEQ80

PRESS SERVICE BUTTON TO ANOTHER PAGE PRESS TEST BUTTON TO EXIT

Page 57

I. BACKUP RAM CLEAR

Clears contents of BOOKKEEPING, operating time, coin/credit data, number of games played, ete.

BACKUP RAM CLEAR

YES (CLEAR) > NO (CANCEL)

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

Selecting YES clears the aforementioned data. Select NO and press TEST Button to have the MENU mode return without clearing data.

Note that this does not affect the data of BOOKKEEPING in GAME TEST Mode. To clear the contents of BOOKKEEPING in GAME TEST Mode, enter into GAME TEST Mode and execute BACKUP DATA CLEAR.

J. ROMBD TEST

In this test, on-ROM-BD ROM check is executed. If GOOD is displayed, it is satisfactory. The IC No., TYPE, RESULT, BYTE, and WORD refers to the check sum of each unit. Press TEST Button to return to MENU mode.

ROMBD TEST [XXXXXXXXXXXXXXX] [XXXXXXXXXXXXXXXXXXXXXXXXXXXXX]

jO. TYPE RESULT BYTE WORD 1C29 32M - XXXX XXXX 1C30 32M - XXXX XXXX 1C31 128M GOOD xxxx xxxx

1C50 128M GOOD xxxx xxxx

PRESS TEST BUTTON TO EXIT

Page 58

K. CLOCK SETTING

YEAR, MONTH, DAY, HOUR, and MINUTE are set for SEGA HIKARU BD. Select the desired item with SERVICE Button and press TEST Button to increase the value. Bring the arrow to EXIT and press TEST Button to return to MENU Mode.

CLOCK SETTING

1999 07/07 07:07 07 07 WED

YEAR MONTH DAY HOUR MINUTE SECOND

-> EXIT CANCEL

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

L. GAME TEST MODE

Enters the TEST Mode of the game connected to SEGA HIKARU BD. The TEST Mode

includes INPUT Test, GAME ASSIGNMENTS such as game difficulty, etc. Refer to 9-3 for details.

Page 59

9-3 GAME TEST MODE

A. MENU SCREEN

The Game Test Mode Menu Screen is displayed by selecting and executing "GAME TEST MODE" on the System Test Menu Screen. In the Game Test Mode, you should perform the tests and settings about the I/O devices dedicated to this product.

Operation method is same as in the SYSTEM TEST MODE. By pressing SERVICE Button, move the arrow to the desired item and press TEST Button to execute/change the selected item.

SYSTEM MENU

RAM TEST JVS TEST

SYSTEM ASSIGNMENTS COIN ASSIGNMENTS. BOOKKEEPING BACKUP DATA CLEAR ROMBD TEST CLOCK S| PING > GAME TEST MODE EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON GAME MENU

INPUT TEST OUTPUT TEST GAME ASSIGNMENTS, BOOKKEEPING CALIBRATION BACKUP DATA CLEAR > EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

FIG. 9.3 a GAME TEST MODE MENU screen

Page 60

B. INPUT TEST

CAUTION! In this mode, the Skate Board is unlocked. Entering this mode while the player is on the Skate Board can cause falling down accidents. Use care to avoid injury.

Selecting "INPUT TEST" displays the following screen, where you can view the switch settings and the Volume Control values of each cabinet. Periodically check the switch and Volume Control settings on this screen. If the indicator to the right of the name of a switch turns "ON" from "OFF" when the switch is pressed, this switch and its wiring are normal.

INPUT TEST NODE V1 BUTTON START OFF LEFT OFF RIGHT OFF UP OFF DOWN OFF SERVICE OFF TEST OFF VOLUME YAW 80

ROLL 80

PRESS TEST AND SERVICE BUTTON TO EXIT

FIG. 9.3 ba INPUT TEST screen

@ UP and DOWN indicate the status of the sensors that detect kicking on the front and back of the Controller Board (i.e., Skateboard). (FIG. 9.3bb).

@ YAW is the Volume Control value with which the left and right swings of the Skateboard are detected. ROLL is the Volume Control value with which the tilt relative to the horizontal surface is detected. (FIG. 9.3bb).

@ Pressing the TEST and SERVICE Buttons together causes the Menu Screen to return.

Page 61

YAW

UP, DOWN ROLL

FIG. 9.3 bb

At the time of centering the Volume (the Controller Board is level and faces the front), the Volume value is set to 180H + 08, and if the Volume value varies in a natural manner matching the operation of the Controller Board and meeting the operation in the right/left direction evenly, then the product allows for satisfactory play.

If the Volume value is widely deviated from the 80H + 08 which is set at the time of centering, or the value does not vary evenly in the right/left operation, the game can not be played satisfactorily, and also this causes Volume damage. Adjust the Volume by referring to "F. CALIBRATION", or adjust the gear engagement of the Volume by referring to Section 10, or replace the Volume.

Page 62

C. OUTPUT TEST

In this mode, the Skate Board is unlocked. Entering this mode while the player is on the Skate Board can ca ling down lents. Use care to avoi

CAUTION!

Selecting "OUTPUT TEST" displays the following screen, where you can view the lamp positions. Select the desired item using the SERVICE Button. Then press the TEST Button. The indicator to the right of the name of the currently selected item turns "ON" from "OFF". If the lamp associated with the selected item lights up and the Skateboard is locked when the indicator is "ON", the functionality is normal. Pressing the TEST Button causes the Menu Screen to return.

OUTPUT TEST

LEFT UPEER LAMP OFF LEFT LOWER LAMP OFF RIGHT UPEER LAMP OFF RIGHT LOWER LAMP OFF START LAMP OFF LOCK MECHA OFF > EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

FIG. 9. 3c a OUTPUT TEST screen

START LAMP

LOCK MECHA,

\RIGHT LOWER LAMP

FIG. 9.3¢b

Page 63

D. GAME ASSIGNMENTS

Selecting "GAME ASSIGNMENTS" displays the following screen, where you can make the settings about the game. If change is made to the settings, return to the Menu Screen and select and execute EXIT to exit the TEST MODE. The new settings will not take effect unless the TEST MODE is exited. The items represent the following:

GAME ASSIGNMENTS

STAGE SELECT TUTORIAL FIRST WEB RANKING ON LANGUAGE JAPANESE ONLY > EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

FIG. 9.3 d GAME ASSIGNMENTS screen

@ STAGE SELECT Set the stage that was selected first when the Select Stage Screen appears before the game starts. Select either SCORE ATTACK FIRST (center) or TUTORIAL FIRST (left). The stage being selected first is only set, but the restrictions to player selection are not set.

@ WEB RANKING

ON : The URL of the home page is displayed during the Advertise Mode, or the

password for the home page is displayed when the game is over. OFF : Neither the URL nor the password is displayed.

@ LANGUAGE Select the desired language from FRANCOIS, ESPANOL, ITALIAN, and ENGLISH.

SETTING CHANGE PROCEDURE

® Press the SERVICE Button to bring the arrow (>) to the desired setting change item. @Press the TEST Button to choose the desired setting item. @pBring the arrow to EXIT and press the TEST Button to return to the menu mode.

Page 64

E. BOOKKEEPING

You can view data about the game play time etc. Pressing the TEST Button causes the Menu Screen to return.

TUTORIAL SET-A SET-B

AVERAGE TIME

JAKE SPIDEY KYATIE LINDA TONY BOOKKEEPING

NUMBER OF GAME

CHARACTER COUNT

PRESS TEST BUTTON TO EXIT

FIG. 9. 3a BOOKKEEPING screen

@ NUMBER OF GAMES

@ TUTORIAL

@SET-A

@SET-B

@ PLAY TIME

@ CHARACTER COUNT : Number of games that were played.

: Number of games that were played by selecting the left stage on the Select Screen.

: Number of games that were played by selecting the central stage on the Select Screen.

: Number of games that were played by selecting the right stage on

the Select Screen.

: Total time of games played.

: Count of selection made for each character.

Page 65

F. CALIBRATION

CAUTION!

IMPORTANT

In this mode, the Skate Board is unlocked. Entering this mode while the player is on the Skate Board can cause falling down accidents. Use care to avoid injury.

When the Volume is adjusted or replaced, be sure to set the Volume value in the CALIBRATION mode.

Selecting CALIBRATION on the Menu Screen displays the following screen. You can determine the YAW and ROLL Volume Control values with which operation of the Skateboard is detected.

CALIBRATION

VOLUME CALIBRATION YAW : 78 <-> 79 ROLL: 85 <-> 86 > EXIT

SELECT MENU WITH SERVICE BUTTON AND PRESS TEST BUTTON TO START CALIBRATION

FIG. 9. 3 fa CALIBRATION screen

HOW TO VOLUME SETTING

Select "VOLUME CALIBRATION" using the SERVICE Button. Then press the TEST Button. The screen changes to the one shown in FIG. 9.3fb.

Get on the Skateboard. Then, set the minimum and maximum values of the Volume Control by operating YAW (left-right) and ROLL (tilt) even in both directions. If a large width of input is set, the Skateboard will be hard to make a turn. If a small width of input is set, it will be easy to make a turn.

@ Pressing the SERVICE Button exits VOLUME CALIBRATION.

® With EXIT selected, pressing the TEST Button causes the Menu Screen to return.

Page 66

If the Volume Control value is not set within 80 + 08 H when the Skateboard is horizontally placed in the progressive direction, improper engagement of the Volume Control gears or the Volume Control itself may be faulty. Take the proper action according to the instructions in Section 10.

CALIBRATION

VOLUME CALIBRATION YAW : 3C <-78-> B3 ROLL: 6E <-90-> 98 > EXIT

MOVE FOOT CONTROLLER TO THE EDGE IN ANY DIRECTION PRESS TEST BUTTON TO FINISH CONFIGURATION

FIG. 9.3 fb CALIBRATION screen

After operating the Skate Board evenly in both directions.

FIG. 9.3 fe

Page 67

G. BACKUP DATA CLEAR

This screen enables to clear the data of bookkeeping and to initialize the high-scorer ranking data.

BACKUP DATA CLEAR

YES (CLEAR) >NO (CANCEL)

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

FIG. 9. 3 g BACKUP DATA CLEAR screen

  • To clear the data: Press the SERVICE Button to move the > mark to YES, and press the TEST Button. When clearing is finished, the COMPLETED message appears on the screen. Press the TEST Button, in this instance, to return to the GAME TEST MODE screen.
  • Not to clear the data: Press the SERVICE Button to move the > mark to NO, and press the TEST Button. This action enables you to immediately return to the GAME TEST MODE screen.
  • What you can clear on this screen is the bookkeeping data accessible from the GAME TEST MODE screen. You cannot clear the bookkeeping data and settings accessible from the SYSTEM MENU screen.
Page 68
  • MAINTENANCE OF CONTROLLER MECHANISM UNIT

Before starting to work, ensure that the Power SW is OFF. Failure to observe this can cause electric shock or short circuit.

W, G! Use care so as not to damage wirings. Damaged wiring can cause electric

shock or short circuit. Do not touch undesignated places. Touching places not designated can cause electric shock or short circuit. This work should be performed by the Location's Maintenance Man or Serviceman. Performing work by non-technical personnel can cause electric shock hazard. Do not perform work other than those specified in this Manual in order to prevent accidents during performing work and operation after performing work. Performing work not specified in this Manual may require special training for this product. If performing work other than those stated in this manual is required for repair, contact the offices herein stated in this manual or where you purchased the product from and ask for repair or inquire how to repair. Take care not to get caught in the gears or the Mechanism Assembly. If you encounter such an accident, you may be seriously injured (e.g., a bone factures, or of your body is cut). Take care not to lose any fasteners or their related parts (e.g., screws, bolts, washers). If a metallic fastener or its related part touches a conductive part, a short circuit or fire may be caused.

The Skateboard (i.e., Controller Board) is equipped with the following operational input devices: a ROLL- and a YAW-direction detection Volume Control and a kicking sensor. Verify operation of the input devices in the Test Mode at least once a month. If a failure is found, take action immediately. This document explains how to adjust and replace a spare Volume Control. The Mechanism Assembly is required to be greased up.

10 - 1 ADJUSTING/REPLACING THE ROLL-DIRECTION VOLUME CONTROL

The Volume Control used to detect the Skateboard ROLL-direction (tilt) is located under the Skateboard, toward the rear. The following work requires a Phillips screwdriver for M4 screws, a flat-tipped screwdriver for M3 screws, and a wrench with an inter-opposite side distance of 11 mm.

Page 69

® Turn off power.

Remove the 6 Bellows Holder securing the bellows located under the Skateboard. Remove the 2 screws.

BELLOWS HOLDER

SCREW (2 each), blac!

BELLOWS HOLDER (6 in total a

BELLOWS HOLDER (6 in total) M4 X 12, w/flat & spring washers

PHOTO 10. 1a

@Remove the 2 truss screws located on the top surface of Floor Board Rear.

TRUSS SCREW (2), black M4 X 25, flat washer used.

PHOTO 10. 1b

Page 70

® Remove the 3 truss screws from the back of the Rear Cabinet.

TRUSS SCREW (3). Se

M4 X 8, chrome plated ‘ :

PHOTO 10. 1c

® Remove Floor Board Rear. The ROLL-direction Volume Control Mechanism Assembly is seen by raising the bellows.

FLOOR BOARD REAR

PHOTO 10. 1d

Page 71

Adjusting Procedure

Loosen the 2 screws securing the ROLL VR Holder.

SCREW (2) M4 X 8, wiflat & spring a 2; [ fam (cat maw sant

FIG. 10.1 a

@ Adjust the top and bottom positions of the ROLL VR holders so that the D-Cut side of the Volume Control spindle faces up when the Skateboard is placed horizontally. @ Retighten the 2 loosened screws. @with power on, check the volume control values in the Test Mode. (See Section 9-3 B)

Replacing Procedure

® Pull out the connector connected to the Volume Control. Then unfasten the wire.

Disconnect the connect

PHOTO 10. le

Page 72

@ Remove the 2 screws securing SCREW (2)

the ROLL VR Holder. 4 X 8, w/flat & spring washers

PHOTO 10.1 f

Remove the ROLL VR Holder with the Volume Control installed.

PHOTO 10.1 g Loosen the 2 cheese machine screws securing the crank.

CHEESE MACHINE SCREW (2)

PHOTO 10. 1h

Page 73

Pull out the crank from the Volume Control spindle.

PHOTO 10. 1i

@)Remove the hexagon nut securing the Volume Control to the ROLL VR Holder.

HEXAGON NUT VOLUME 220-5484

PHOTO 10. 1j

Ow replace the Volume Control, remove it from the ROLL VR Holder.

Install a new Volume Control to the ROLL VR Holder, and secure the crank. Paying attention to the angle of installation illustrated in the figure, secure the ROLL VR Holder. (See FIG. 10.1a.)

Connect the connector and secure the wire firmly. The wire may be disconnected by being caught in the Mechanism Assembly. Check that there is not the danger that movement of the Mechanism Assembly to either limit of the movable range may damage the wire.

(with power on, adjust the Volume Control values in the Test Mode. (See Section 9-3F)

Page 74

10 - 2. ADJUSTING/REPLACING THE YAW-DIRECTION VOLUME CONTROL

The Volume Control used to detect the Skateboard YAW direction (turn) is located under Table Lid L to the left of the Skateboard when facing the PTV screen. The following work requires a Phillips screwdriver for M4 screws, a flat-tipped screwdriver for M3 screws, and a wrench with an inter-opposite side distance of 11 mm.

® Turn off power.

Remove the 2 screws securing Table Lid L, located to the left of the Skateboard.

SCREW (2), black M4 X 20, w/flat & spring washers

PHOTO 10. 2a

Table Lid L can be removed by sliding it toward the Skateboard. The YAW-direction Volume Control Mechanism Assembly is seen by removing Table Lid L.

TABLE LIDL

PHOTO 10.2b

Page 75

Adjusting Procedure

@ Loosen the 2 screws securing the @ Adjust the angle for securing the

YAW VOL Holder.

YAW VOL Holder so that, when the Skateboard is placed in the progressive direction, the D-Cut side of the Volume Control spindle faces left.

@pRetighten the 2 loosened screws (Q) With power on, check the Volume

for securing.

Control values in the Test Mode. (See Section 9-3B)

D-CUT SIDE,

Replacing Procedure

Pull out the connector connected to the Volume Control. Then unfasten the wire.

Disconnect the connector.

@ Remove the 2 screws securing the

YAW VOL Holder.

SCREW (2), black

M4 X 8, wiflat & spring washers

SCREW (2), black M4 X 8, wiflat & spring washers

/ Oo

o oO

©

FIG. 10.2a

PHOTO 10.2¢

PHOTO 10. 2d

Page 76

® With the Volume Control installed,

remove the YAW VOL Holder.

Loosen the 2 cheese machine screws securing the Gear Wheel. PHOTO 10.2¢

CHEESE MACHINE SCREW (2) M3 X6

PHOTO 10. 2f

  • Draw out the Gear Wheel from the Volume Control spindle.

PHOTO 10.2 ¢

Page 77

@®Remove the hexagon nut securing the Volume Control to the YAW VOL Holder.

HEXAGON NUT

PHOTO 10. 2h

@ro replace the Volume Control, remove it from the YAW VOL Holder.

VOLUME, 220-5484

PHOTO 10. 2i

@®nstall anew Volume Control to the YAW VOL Holder, and secure the gear wheel. Paying attention to the angle of installation illustrated in the figure, secure the YAW VOL Holder. (See FIG. 10.2a.)

©) Connect the connector and secure the wire firmly. The wire may be disconnected by being caught in the Mechanism Assembly. Check that there is not the danger that movement of the Mechanism Assembly to either limit of the movable range may damage the wire.

(with power on, adjust the Volume Control values in the Test Mode. (See Section 9-3F)

Page 78

10-3 GREASING

WARNING! Grease is inflammable and must never be close to fire. Grease may be apt to be erroneously used or drunk, and must not be placed in a location where children can access.
CAUTION! Grease does harm to your body if you aspirate it. Do not perform any work related to grease in a location where ventilation is insufficient. f grease enters an eye, eye irritation may be caused. Take care to prevent it from entering your eyes (for example, by wearing protective goggles). Should grease enter an eye, rinse it in clean water and have your illness diagnosed by a doctor. f grease touches a human skin, skin irritation may be caused. Take care to prevent grease from touching your skin (for example, by wearing protective gloves). Should grease touch your skin, fully wash it using water and soap. Do not eat grease. Should you eat it, you may have loose bowels or feel like vomiting. Should somebody swallow it, immediately have his or her illness diagnosed y a doctor, without compelling him or her to vomit the grease. When attempting to open the bottle of grease, your hand may be cut. To prevent this, use protective gloves. The way of treating grease is regulated by law. Treat it legally according to the local law for the setup site. Illegal treatment of grease may cause environmental pollution. If you do not know how to treat grease, contact the dealer from which you bought it.

IMPORTANT

Be sure to use the designated type of grease. If a non-designated type grease is

used, components may break. To prevent dust or water from mixing into the grease, firmly cork the grease bottle for sealing. Store the grease in a dark place not exposed to direct sunlight. The period for greasing specified herein is a standard. Apply greasing to the specified portions as occasion arises.

Grease the swing bearing, once a month, with the Special Grease accompanying the product. In addition, grease the gear mesh portion and the crank sliding portion of the Volume Control Mechanism Assembly, and the mesh portion of the pinion gears (for locking the Skateboard).

Page 79

Greasing the Swing Bearing

When greasing the swing bearing, move the Skateboard fully to the clockwise or counterclockwise end to allow grease to reach every part of the bearing. When

CAUTION! performing this work, hold the handrail firmly to prevent you from falling down.

S @ For the swing bearing, be sure to use the Special Grease accompanying the

product. The same type of grease is injected for shipment. Using another type of

grease may cause a chemical change, thereby causing the system to be unavailable or hang up. When the Special Grease is used up, place an order with your dealer for another bottle of grease. When operating the Grease Gun lever, be sure to either open or close fully. If it is operated halfway, the grease cannot be injected. If the grease does not come out when the lever is operated, this may be due to an air pocket in the grease. To resolve this, warm the Lubricant Tube once or twice to release the air. The weight of grease used at a time should be 16 g. Injecting more grease results in the same effect.

IMPORTANT

To grease the swing bearing, prepare the following:

  • Grease Gun (540-0064)
  • Special Grease (090-0275)
  • Protective goggles
  • Protective gloves + Phillips screwdriver for M4 screws + Master key

Remove Table Lid R, which is located to the right of the Skateboard when facing the PTV screen. Remove the 2 screws securing it.

“a screw eo, me AS/, M4 X 20, w/flat & spring washers

PHOTO 10.3 a

Page 80

@ Table Lid R can be removed by sliding toward the Skateboard.

TABLE LIDR

ieee

PHOTO 10.3 b

Once Table Lid R is removed, the

Grease Nipple for greasing is seen.

GREASE NIPPLE

(| y | PHOTO 10.3 ¢

® Install the Grease Gun nozzle to the body of the gun.

LEVER

LUBRICANT TUBE

NOZZLE

CHAL

FIG. 10.3 a

Page 81

Screw back the Lubricant Tube to remove it from the body.

PHOTO 10.3 d

©@pull the chain to lock it to the

grooves in the Lubricant Tube.

PHOTO 10.3 €

Remove the cap from the Special Grease bottle, and directly pour it into the Lubricant Tube. At this time, take care not to allow air or dust to mix into the grease.

PHOTO 10. 3 f

Page 82

@Retun the Lubricant Tube to the

body as before.

@®)Unlock the chain and store it in the while moving the lever between

Lubricant Tube.

the opposite ends twice or three times, checking that the grease comes out from the tip of the nozzle.

Enter the Test Mode and unlock the Skateboard. (See Section 9-3B or C)

(DWith the Skateboard turned fully

to either the clockwise or counterclockwise end, insert the Grease Gun nozzle into the Grease Nipple. PHOTO 10.3 g

PHOTO 10. 3h

PHOTO 10. 3i

Page 83

40D 4100 y

FIG. 10.3b

Pour approximately 0.8 g of grease during one reciprocating motion of fully opening and closing the lever. Thus, pour a total of 8 g of grease during eight reciprocating lever motions.

@®Tun the Skateboard fully to the opposite end, and secure it there. (©) Pour a total of 8 g of grease during ten reciprocating lever motions. @®rTurn the Skateboard clockwise and counterclockwise several times to allow grease to reach every part of the swing bearing.

Because the grease in the Lubricant Tube will be used for the next greasing work, store it in the tube. Lock the chain for storage. At time of the next greasing work, the grease in the nozzle will have been altered in quality because it will have been exposed to the outside air. Move the lever between the opposite ends twice or three times, and drain the grease from the nozzle. Then insert it into the nipple.

Page 84

Greasing the Volume Control Mechanism Assembly

Grease the gear mesh portion of the Volume Control Mechanism Assembly and the crank sliding portion once every three months. For this purpose, use spray grease Grease Mate (Part No. 090-0066). Make the Volume Control Mechanism Assembly seen externally, according to the instructions in Sections 10-1 and -2. With an extension tube installed to the outlet of the spray grease, apply it to the gear mesh portion and the crank mechanism sliding portion. The gears of the YAW-direction Volume Control Mechanism Assembly are of two-step type. Apply the grease also to the gear mesh portion at the lower step.

PHOTO 10. 3j PHOTO 10.3 k ROLL-Direction Volume Control Mechanism Assembly YAW-Direction Volume Control Mechanism Assembly

Greasing the Pinion Gears Mesh Portion

The pinion gears are used to lock the Skateboard. Grease the pinion gears mesh portion once every three months. For this purpose, use spray grease Grease Mate (Part No. 090-0066). To perform the greasing, keep the ROLL-Direction Volume Control Mechanism Assembly seen externally. (See Section 10-1.) With an extension tube installed to the outlet of the spray grease, apply it to the gear mesh portion of the gears.

PHOTO 10.31 Pinion Gear

In the photograph, as a matter of convenience the turn table has been removed to allow the pinion gears to be seen externally. Actually, the greasing can be performed without removing the gears.

Page 85

10 - 4 REPLACING THE ACCIDENT AVOIDANCE SYSTEM

If the hazard preventive parts have any irregularity, be sure to replace the part(s) immediately. Operating with the part(s) as is damaged or omitted can cause

WARNING! |_iiury.

If the bellows under the Skateboard broken, replace them immediately. The following work requires a Phillips screwdriver for M4 screws and a socket wrench (or spanner) for M8 hexagon bolts.

® Turn off power.

@ Remove the 3 screws from each of the 2 end and 2 side bellows sashes securing the bellows to the Skateboard.

=

PHOTO 10. 4a black SCREW (3 each), M4 X 12, w/flat & spring washers END BELLOWS SASHE

SCREW (3 each), black M4 X 12, w/flat & spring washers SIDE BELLOWS SASHE

a

PHOTO 10. 4b

Page 86

Release a total of 6 hooks (3 hooks

at each side) and lower the bellows.

Pull out the 2 connectors. Release all the cord clamps securing the wire of the connector that was pulled out.

Disconnect the connector.

PHOTO 10. 4¢

Remove the 4 hexagon bolts securing the ASSY Skateboard.

HEXAGON BOLT (4) M8 X 16, w/flat & spi

PHOTO 10.4d

HEXAGON BOLT (4) MB X 16, w/flat & spring washers

FIG. 10.4

Page 87

Remove the ASSY Skateboard. At this time, take care not to damage the wiring.

PHOTO 10. 4e

Remove the 6 Bellows Holder securing the bottom of the bellows. Remove the 2 screws from each of the holders.

Replace the bellows.

BELLOWS HOLDER

AS

BELLOWS, ATR-3102

SCREW (2 each), black, M4 X 12, wiflat & spring washers PHOTO 4¢

Page 88

11. PROJECTOR

Ay Since the Projector has been adjusted at the time of shipment, avoid making further adjustments without good reason.

CAUTION!

The Projector is subject to color deviation due to Convergence deviation caused by the geomagnetism at the installation location and peripheral magnetic field. After the installation of machine, and before commencing operation, check for Convergence deviation and if deviated, make adjustments.

IMPORTANT

Projector adjustments are stored. Due to distortion or color deviation in the TEST mode, if an adjustment is necessary, use the Remote Control to make adjustments. There are two Projector Makers (Toshiba and Mitsubishi) and the adjustment method varies depending on the specific maker.

11 - 1 CLEANING THE SCREEN

Since the Projector screen is susceptible to damage, pay careful attention to its handling. When cleaning, refrain from using water or volatile chemicals.

CAUTION!

When the screen surface ecomes dirty with dust, etc., clean it by using a soft cloth such as gauze. When water, and volatile chemicals such as enzine, thinner, etc., spill on the screen surface, it may be subject to damage, therefore, do not use them. Also, since the surfaces are susceptible to damage, refrain from rubbing them with a hard material or using a duster.

FIG. 11.1

Page 89

11-2 ADJUSTMENT OF TOSHIBA PROJECTOR

SETTING THE INTERFACE

In this product, set to INPUT LEVEL: 0.7V and IMPEDANCE: 75Q. Failure to observe this can cause CRT membrane to burn or Shutdown device to function resulting in power off.

IMPORTANT

The Projector's Connector Panel contains the Interface setting SW.

  • (0) () oe WINNER AC IN LAMP scioo-120¥~ “RGBIN IMPEDANCE INPUT LEVEL [eo

REMOTE CONTROL BUTTONS

When adjusting the Projector, direct the Remote Control's light emitting portion towards the Projector Screen.

REMOTE CONTROL LIGHT EMITTING PORTION

MODE (mode selection) f \ WRITING (storing the data) TEST (adjust/normal shift)

SS ‘SO P (automatic color matching)

I in 6.8 $ 6 3 SET (to decide the selection) PIC - ADJ (item selection) O(OlO Aq Ai Adittem selection) R. G.B. (color selection)

POSITION (to select the position) ES aes | TT I RESET eo/é| es

ADJUST (adjustment) lo @ ie x SELECT (pattern selection)

+) sec

NE”

Page 90

AUTOMATIC COLOR MATCHING

The Projector may be subject to color deviations affected by earth magnetism, the building steel frames, etc. When the Projector is initially installed or the Projector's installation position is changed, have the color matching performed automatically.

® Keep pressing the P button (red) for approximately 3 seconds to have

the ensuing movements performed automatically.

The Projector will shift to the color deviation cor-

® rection mode from the game mode, with the green

cross pattern appearing on the screen.

an The cross pattern moves up/down and right/left to i @ © > ©

ION (9) co) o\e

start the movement of searching the correct screen [- position and inclination.

When the green cross pattern movements are finished, similar detection is performed sequentially in order of red and then blue cross movements. After detecting by green, red and blue cross movements, the game mode returns with the color deviation status being corrected.

@ Although very rarely, the TRY AGAIN error display in red may appear. At this time, press the P button (red) for approximately 3 seconds. Even after the above operation is repeated, if the error condition still exists, then the display shifts to PLEASE ADJ. In this case, the auto color matching function can not be used. Contact the place of contact herein stated or where the product was purchased from.

@ [fthe automatic color matching indicates an error, color matching can manually be performed. Refer to CONVERGENCE ADJUSTMENT (manual color matching).

Page 91

ADJUSTING THE ON-SCREEN CONTRAST

Although the on-screen picture quality has been adjusted at the time of shipment from the factory, the on-screen contrast can be readjusted if desired. When the Game Board is replaced, readjustment may be necessary. Changing the CONTRAST causes the light and shade of the on-screen images to be changed. ® Press either 4. or W PIC - ADJ button.

The on-screen menu will have CONTRAST lees BRIGHTNESS one item in purple and 6 items

6 6 6 vail ®@ Sar

@ @

@) Choose CONTRAST by using either 4 or W

¥ A Herein, 2) A PIC - ADJ button. Vv. oe -@ 73@ procedure | ene pon at PIC-ADJ Have CONTRAST displayed is skipped. CON TRAS I in purple. Since CONTRAST Me H.POSI is selected initially, no V.POSI particular operation is required H.SIZE Hi V'SIZE in this case. EXIT

SET ® Press the SET button (to decide selection). When the selection of the CONTRAST adjustment mode is decided, the adjustment data scale bar appears on the screen. CONTRAST 230 [pacnene Bpcacsas4 Cae

Make adjustment by using either <4 or > ADJUST ADJUST button.

adjustment data value changes. Make adjustment so as to obtain the desired on-screen contrast status. CONTRAST 156 aes Bprocsaseed 7

WRITING ® Press the WRITING button (for storing and finish).

The WRITING display appears and the adjustment data is stored.

WRITING

@ When discontinuing the adjustment, choose EXIT from the menu at the stage of procedure @ and press the SET button. To continue adjusting other menu items, repeat procedure @ ~ ®. Unless the adjustment data is stored, the data in the adjusted status will be erased at the time the power is turned off and the pre-adjustment status will remain when the power is turned on next time.

Page 92

ADJUSTING THE SCREEN BRIGHTNESS

Although the on-screen picture quality has been adjusted at the time of shipment from the factory, readjustment can be made if desired. When the Game Board is replaced, readjustment may be necessary. Changing the BRIGHTNESS causes the brightness of the on-screen images of black portions to be changed.

PIC-ADJ Vv = = ) @ oe @- @ @ oe

g eo IS) Pe ® @\® @e

@;® Oe = © A ® Pre

CONTRAST BRIGHTNESS H.POSI V.POSI H.SIZE V.SIZE EXIT seither 4. or W PIC - ADJ button.

The on-screen menu will have one item in purple and 6 items in white.

Choose BRIGHTNESS by using either 4 or W PIC

  • ADJ button. oe i> <4

PIC-ADJ Fi

SET

WRITING CONTRAST BRIGHTNESS H.POSI V.POSI H.SIZE V.SIZE EXIT

BRIGHTNESS

button.

BRIGHTNESS remo EE peee sa or

WRITING Have the BRIGHTNESS displayed in purple.

® Press the SET button (to decide selection).

When the selection of the BRIGHT- NESS adjustment mode is decided, the adjustment data scale bar appears on the screen.

® Make adjustment by using either < or > ADJUST

As the Cursor is moved, the adjustment data value changes. Make adjustment so as to obtain the desired on-screen brightness status.

  • Press the WRITING button (for storing and finish).

The WRITING display appears and the adjustment data is stored.

When discontinuing the adjustment, choose EXIT from the menu at the stage of procedure @ and press the SET button. To continue adjusting other menu items, repeat procedure @ ~ 0) . Unless the adjustment data is stored, the data in the adjusted status will be erased at the time the power is turned off and the pre-adjustment status will remain when the power is turned on next time.

Page 93

ADJUSTING THE ON-SCREEN DISPLAY POSITION

Although the on-screen display position (H. POSI, V. POSI) has been adjusted at the time of shipment from the factory, readjustment can be made if desired. When the Game Board is replaced, readjustments may be necessary.

@ PIC-ADJ V = eB g @: \®@ @e @ @ © @ @ @

? ee S) Ee = @ Cy te :

A PIC-ADJ Vv | e\e/e wust Je <> 4

ADJUST

When making adjustments in vertical directions, also use either < or > ADJUST button.

WRITING

press the SET button. CONTRAST BRIGHTNESS H.POSI V.POSI H.SIZE V.SIZE EXIT

PIC ADJ button.

CONTRAST BRIGHTNESS H.POSI V.POSI H.SIZE V.SIZE EXIT

button.

WRITING

® Press the SET button (to

To continue adjusting other menu items, repeat procedure @ ~ @. /\ Press either 4 or W PIC - ADJ button. The on-screen menu will have one item in purple and 6 items in white.

Choose H. POSI or V. POSI by using either 4 or W

Have the H. POSI or V. POSI displayed in purple. The Figure shows the status in which H. POSI is selected.

decide selection).

When the selection of the H. POSI or V. POSI is decided, the adjustment data scale bar appears on the screen.

(O) Make adjustment by using either <4 or > ADJUST

As the Cursor is moved, the adjustment data value changes. Make adjustment so as to obtain the desired on-screen position status.

® Press the WRITING button (for storing and finish). The WRITING display appears and the adjustment data is stored.

When discontinuing the adjustment, choose EXIT from the menu at the stage of procedure @ and

Unless the adjustment data is stored, the data in the adjusted status will be erased at the time the power is turned off and the pre-adjustment status will remain when the power is turned on next time.

Page 94

ADJUSTING THE SCREEN SIZE

a @/@-@ @ oe! @ :

z Although the on-screen size (H. SIZE, V. SIZE) has been adjusted at the time of shipment from the factory, readjustment can be made if desired. When the Game Board is replaced, readjustments may be necessary.

PIC-ADJ yj @ < Coe r ® ee

-® QO &

.@! (®)

«= AbUUST

When making adjustments in vertical directions, also use either <q or > button.

WRITING. Press either & or W PIC - ADJ button.

CONTRAST BRIGHTNESS H.POSI V.POSI H.SIZE V.SIZE EXIT

PIC - ADJ button.

CONTRAST BRIGHTNESS H.POSI V.POSI H.SIZE V.SIZE EXIT

® Press the SET button

button.

WRITING The on-screen menu will have one item in purple and 6 items in white.

@ Choose H. SIZE or V. SIZE by using either & or W

Have the H. SIZE or V. SIZE displayed in purple. The Figure shows the status in which H. SIZE is selected.

(to decide selection).

When the selection of the H. SIZE or

V. SIZE adjustment mode is decided, the adjustment data scale bar appears on the screen.

Make adjustment by using either <q or > ADJUST

As the Cursor is moved, the adjustment data value changes. Make adjustment so as to obtain the desired on-screen position status.

® Press the WRITING button (for storing and finish). The WRITING display appears and the adjustment data is stored.

When discontinuing the adjustment, choose EXIT from the menu at the stage of procedure @ and press the SET button. To continue adjusting other menu items, repeat procedure @ ~ ® . Unless the adjustment data is stored, the data in the adjusted status will be erased at the time the power is turned off and the pre-adjustment status will remain when the power is turned on next time.

Page 95

CONVERGENCE ADJUSTMENT (manual color matching)

A

CAUTION!

IMPORTANT

To avoid circuitry malfunctioning due to electrical load increase, never utilize CONVERGENCE ADJUSTMENT (Line Convergence Adjustment in particular) for adjusting screen size changes. There is no means to restore the Convergence Adjustment data once stored, to its original state. To avoid changing the screen size by erroneously using convergence adjustment, do not perform the green Line Convergence Adjustment. As such, be sure to perform the adjustment work from this page onward by the Technical staff and the location's Maintenance Personnel who are well versed in such adjustment work. In the Static Convergence Adjustments, if satisfactory adjustments can not be performed, do not make another convergence adjustments inadvertently. Contact the office herein stated or where the product was purchased from.

@ To avoid making the adjustment work ineffective, do not press the RESET button during adjustment.

@ To discontinue adjustment work, keep pressing the TEST button for approximately 3 seconds at the stage before storing the adjustment data by pressing the WRITING button.

Should the screen be abnormally disturbed by noise due to static electricity, etc., turn the power off without storing the adjustment data. Pressing the & or W PIC - ADJ button in the Convergence Adjustment mode status will display the Adjustment Menu shown right. Do not utilize this Adjustment Menu as this is the one

applied at the factory. Sue Naas

SUB BRIGHT EXIT ADJUST

Adjusting this menu causes the Customer's adjustment range to be deviated. Adjustment menu used in the factory. Should the menu shown right be displayed by mistake, first choose EXIT by using either 4 or W PIC- ADJ button and then press the SET button.

Page 96

STATIC CONVERGENCE ADJUSTMENT

In the static convergence adjustment, each of red and blue images is comprehensively moved to and superimposed on the green color. If automatic color matching function is not sufficiently satisfactory, perform this adjustment. Be sure to perform automatic color matching before starting the above adjustment.

When either of (2) @) COLOR

SELECT buttons (R, B) is pressed, if the color desired to be adjusted disappears, press that particular button again. For example, if the red color needs to be

adjusted again at the stage of ® ,theR

button need to be pressed twice. DO NOT PUSH THIS. Keep pressing the TEST button for approximately 3 seconds.

[ADIOS MODE— The screen will change to ADJUST mode from the Game mode to cause the green test pattern to be displayed on the screen.

@ Press the R button to have the red adjustment

mode.

[—ADIUS}] MODE— The red test pattern is added to the display. The frame color turns red and this signifies the red adjustment mode.

@) Make adjustment by using the & W < > ADJUST button: S.

[—ADIUSF MODE— Make adjustment so as to have red superimposed on green, When red is superimposed on green, the color becomes yellow.

mode.

(@) Press the B button to have the blue adjustment

Similarly as in the case of red, —ADIUY FF MODE— adjust the blue color. When green, red, and blue are superimposed, the color becomes white.

® Press the WRIT!

ADJUSf MODE— ING button (for storing and finish). The WRITING display appears and the adjustment data is stored. After the data is stored, the Game mode returns. ING

Page 97

POINT CONVERGENCE ADJUSTMENT

Note 1
Note 2
Note 3 In the POINT CONVERGENCE adjustment, each of red, green and blue images is partially moved for color matching. The adjustment may be necessary when the Game Board is replaced or changed, or screen size is changed. Be sure to perform automatic color matching before starting the adjustment.

MARKER.

® Keep pressing the TEST button for

approximately 3 seconds.

= ADIUSy MODE— The screen changes to ADJUST mode from the Game mode and displays the green test pattern.

@ Press the MODE button twice to have the POINT

ADJUSTMENT mode. Note 1

=H] The crosshatch test pattern appears and the MARKER indicating the adjust-

When the MODE button is repeatedly pressed, the adjustment modes will circulate as follows:

STATIC ADJUSTMENT MODE

LINE ADJUSTMENT MODE

POINT ADJUSTMENT MODE

When either of the COLOR SELECT

buttons (R, B) is pressed, if the desired color to be adjusted disappears, press that particular button again.

By repeatedly pressing the SELECT button, only the Projector's TEST pattern screen and the screen superimposing the Game Board Test pattern can be alternately displayed. DO NOT PRESS. ment point is displayed.

g) Using either R or B button, select the desired

color to be adjusted. Note 2 By using the G button, the green color can also be selected.

EFEH The selected color is displayed by superimposing on green. The MARKER will be in the color selected.

Ey @) By using © AV << p> ADIUST buttons, move the MARKER to the position to be adjusted. = The MARKER moves in the direction

of the button’s arrow. However, the

movable point is predetermined.

® Make adjustment by using the & W <q > ADJUST buttons.

Although the direct vicinity of the

MARKER's center moves most conspicuously, make adjustment by paying attention to the periphery area also, Shown left is the magnified MARKER periphery.

© Press the SELECT button as necessary to superimpose Game Board images. Note 3

If the test pattern is not displayed in the periphery of the screen, adjustments can be made by pressing the SELECT button to superimpose the test pattern and the Game Board's CRT test screen.

@ Press the WRITING button (for storing and finish). WRITING is displayed and the adjustment data is stored. After the data is stored, the Game Board screen returns.

Page 98

LINE CONVERGENCE ADJUSTMENT

In the LINE CONVERGENCE ADJUSTMENT, the adjustment point of the column line (vertical) or row line (horizontal) is comprehensively moved for color matching. It is convenient to utilize this adjustment when the color of the column line or row line is uniformly deviated.

©

DO NOT PUSH. _

® Keep pressing the TEST button for approximately

3 seconds.

  • aon Tt The screen changes to ADJUST mode

from the Game Board mode and displays the green test pattern.

@ Press the MODE button once to have the POINT

ADJUSTMENT mode. Note 1

The crosshatch test pattern appears MARKER and the vertically long MARKER is

Note | When the MODE button is repeatedly pressed, the adjustment modes will circulate as follows:

STATIC ADJUSTMENT MODE

LINE ADJUSTMENT MODE

POINT ADJUSTMENT MODE: shown.

Using either R or B button, select the desired color to be adjusted. Note 2 Although the green color can also be selected by using the G button, to avoid the screen size change adjustment, do not choose green. The selected color is displayed by superimposing on green. The MARKER will be in the color selected.

@By using the A W < > POSITION buttons, move the MARKER to the position to be adjusted.

Use the <q p> buttons to select the column line, and the MARKER moves

Note 2 When either of the COLOR SELECT

buttons (R, B) is pressed, if the desired color to be adjusted disappears, press that particular button again. in the right/left direction. However, the movable range is predetermined.

Use the QW buttons to select the 4 row line and the MARKER moves in the up/down direction. However, the movable range is predetermined.

B G@) Make adjustment by using the A W <q > ADJUST buttons. The selected column line or row line (shown left is the column line) can be moved in the desired up/down or right/ left directions as applicable.

© Press the WRITING button (for storing and finish). WRITING is displayed and the adjustment data is stored. After the data is stored, the Game Board screen returns.

Page 99

11-3 ADJUSTMENT OF MITSUBISHI PROJECTOR

S @ For the operation of Remote Control, use only the Keys of R/B, A (UP shift), <I (LEFT shift), W (DOWN shift), [> (RIGHT shift), TEST,

IMPORTANT -, +, and PICTURE. Do not press keys other than those explained in this manual. @ When operating the Remote Control, have it point the screen.

The Projector has DYNAMIC CONVERGENCE adjustment functions. This manual does not refer to the functions as the adjustment of DYNAMIC CONVERGENCE is very troublesome and in addition, visual effects are negligible. Very rarely, you cannot solve a color-shift problem even with the adjustment procedure described below. If this is the case, contact where you have procured the projector and ask for further information on the adjustment method.

(UP shift) KEY

(LEFT shift)KEY (RIGHT shift)KEY

(DOWN shift)KEY

R-MUTE G-MUTE B-MUTE +KEY

MITSUBISHI

PICTURE KEY

Page 100

POWER KEY.. - This does not have power ON/OFF function. Does not function even if it is pressed.

*R/B KEY «wee Used to select "R" for red adjustment or "B" for blue adjustment in the STATIC CONVERGENCE ADJUSTMENT mode.

+ A (UP shift) KEY ... Used to move the test cross upward in the STATIC CONVERGENCE ADJUSTMENT mode.

+ <j (LEFT shift) KEY ... Used to move the test cross to the left in the STATIC CONVERGENCE ADJUSTMENT mode.

+ 'W (DOWN shift) .................. Used to move the test cross downward in the STATIC CONVERGENCE ADJUSTMENT mode.

+ [> (RIGHT shift) KEY . Used to move the test cross to the right in the STATIC CONVERGENCE ADJUSTMENT mode.

*TEST KEY This is the ON/OFF key in the STATIC CONVERGENCE ADJUSTMENT mode. In the ON status of this key, the test cross pattern appears in the approximately on-screen center.

  • Used for DYNAMIC CONVERGENCE.

Used to decrease the adjustment data in the adjustment mode of CON- TRAST, BRIGHTNESS, HORIZONTAL/VERTICAL POSITIONS and WIDTH.

Used to increase the adjustment data in the adjustment mode of CON- TRAST, BRIGHTNESS, HORIZONTAL/VERTICAL POSITIONS and WIDTH.

*PICTURE KEY ......................, Used for the ADJUSTMENT mode of CONTRAST, BRIGHTNESS, HORIZONTAL/VERTICAL POSITIONS and WIDTH. Every time this key is pressed, the ADJUSTMENT mode proceeds as follows:

NORMAL CONTRAST BRIGHTNESS H-POSI

  • > OPERATION t—t>) ADJUSTMENT }|—?> ADJUSTMENT }|—?> ADJUSTMENT MODE MODE MODE

V-HEIGHT V-POSI H-WIDTH ADJUSTMENT \}«@— ADJUSTMENT jt ADJUSTMENT }<t— MODE MODE MODE

EXPLANATIONS OF ADJUSTMENT MODES

*CONTRAST.................. Used to vary image contrast. Use + and - keys to adjust.

«BRIGHTNESS .. Used to change image brightness. Use + and - keys to adjust.

*H-POSLI..................., Used to move the image position in the horizontal direction. Use + and - keys to adjust.

-H-WIDTH .. Used to change the horizontal width of image. Use + and - keys to adjust.

*V-POSI......... .. Used to move the image position in the vertical direction. Use + and - keys to adjust.

*V-HEIGHT................... Used to change the vertical width of image. Use + and - keys to adjust.

Page 101

STATIC CONVERGENCE ADJUSTMENT

Press the TEST KEY to change the screen to Red Line Adjustment mode.

Superimpose the red line on the green line. When the red line is superimposed on the green line, the green line turns to yellow or white.

To MOVE RED LINE: Use <q] key to move it left. Use [> key to move it right. Use key to move it upward. Use Vv key to move it downward.

Press the R/B KEY. Changes to the Blue Line Adjustment screen. Every time the key is pressed, "from red to blue" and "from blue to red" are alternated.

SUPERIMPOSING BLUE LINE ON GREEN LINE: Superimposing blue line on green line causes the green line to turn to white.

TO MOVE BLUE LINE: Use <]_ key to move it left. Use [> key to move it right. Use key to move it upward. Use Vv key to move it downward.

Press the TEST KEY. Adjustment is finished. RED 31K

H¥75 Vi-11

R < ———* A

V

B < ———* A

V

AUTOMATIC CANCELLATION OF ADJUSTMENT MODE

In each adjustment mode, only in the case where an effective key input (variation of values and images) is not performed within the time limit indicated below, the adjustment mode is automatically cancelled and finished, shifting to on-screen normal images.

Approximately 6 seconds

Approximately 5 min. CONTRAST BRIGHTNESS H-POSI H-WIDTH V-POSI V-HEIGHT

STATIC CONVERGENCE

Page 102
  • COIN SELECTOR

HANDLING THE COIN JAM

If the coin is not rejected when the REJECT button is pressed, open the coin chute door and open the selector gate. After removing the jammed coin, put a normal coin in and check to see that the selector correctly functions.

CLEANING THE COIN SELECTOR

@ Remove and clean smears by using a soft cloth dipped in water or diluted chemical detergent and then squeezed dry. Never apply machine oil, etc. to the Coin Selector. After cleaning the Coin Selector, insert a regular coin in the normal working status and ensure that the Selector correctly functions.

The coin selector should be cleaned once every 3 months. When cleaning, follow the procedure below: Turn the power for the machine OFF. Open the coin chute door.

Open the gate and dust off by using a soft brush (made of wool, etc.) Remove and clean smears by using a soft cloth

(made of wool, etc.).

dipped in water or diluted chemical detergent and then squeezed dry. @Remove the CRADLE. When removing the retaining ring (E ring), be very careful so as not to bend the rotary shaft. Remove stain from the rotary shaft and shaft

receiving portions by wiping off with a soft © After wiping off as per aD above, further apply

cloth, etc.

a dry cloth, etc. to cause the coin selector to dry completely.

COIN INSERTION TEST

Once every month, when performing the Coin SW Test, simultaneously check the following:

[Does the Coin Meter count satisfactorily?

[Does the coin drop into the Cashbox correctly? Is the coin rejected when inserted while keeping the Reject Button pressed down? FIG. 12a

Insert a coin while keeping the Reject Button

pressed down and “a

check if it is f rejected.

COIN METER

FIG. 12¢

Page 103

13. REPLACING THE FLUORESCENT LAMP, AND LAMPS

nN e

WARNING! e

When performing work, be sure to turn power off. Working with power on can cause electric shock and short circuit hazards. The Fluorescent Lamp, when it gets hot, can cause burn. Be very careful when replacing the Fluorescent Lamp. Be sure to use lamps of the designated rating. Using lamps of undesignated rating can cause a fire or malfunctioning.

AN

CAUTION! To perform work safely and securely, be sure to prepare a step which is ina secure and stable condition. Performing work without using the step can cause violent falling down accidents. Be careful when handling the plastic made parts. Failure to observe this may cause injury due to damage or fragments resulting from damage.

BILLBOARD FLUORESCENT LAMP

@tun off power. @ Use a step for the following work.

@tun off power @ Use a step for the following work Using a short flat-tipped

screwdriver, remove the 2 truss screws securing the FL Cover TRUSS SCREW (2) Plate.

@Draw out the FL Cover Plate

toward you.

@® Replace the fluorescent lamp.

When performing work, prepare a step. M4 X 12, chrome plated

PHOTO 13a

FL COVER PLATE,

PHOTO 13b

FLUORESCENT LAMP 32W:390-5251-32-01) GLOW LAMP:390-5638-5P

PHOTO 13 c

Page 104

BILLBOARD SLIM TUBE

@Mtum off power.

@Use a step for the following

work. Remove the 2 truss screws securing the Billboard Plate. TRUSS SCREW (2)

M4 X 8, chrome plated

PHOTO 13d

@Remove the Billboard Plate by

pulling it out upward.

BILLBOARD PLAT!

PHOTO 13 €

@Remove either one of the left and right acryl holders.

ACRYL HOLDER

[TRUSS SCREW (2) a PHOTO 13 f M4 X 8, chrome plated ore

SLIM TUBE @®Remove the Slim Cover by 90-6579-0999B pulling it out toward the side where the acryl holder was removed. The cover is plastic. Pay attention to that applying load carelessly to it may cause it to break.

@©Replace the Slim Tube. SLIM COVE!

PHOTO 13 g

Page 105

START BUTTON LAMP

® Turn off power.

® Turn off power @ Remove the 6 truss screw

securing the Switch Panel.

TRUSS SCREW (6) M4 X 10, chrome plated PHOTO 13h

SWITCH PANEL

Remove the Switch Panel. The Switch Panel contains wiring connections. Remove this panel, taking care not to damage the wiring.

PHOTO 13i

® Hold both sides of the switch

portion with fingers and pull out from the button's base LAMP 6V 3W(WEDGE BULB) portion. At this time, be careful \30 5160 so as not to damage the wiring connected to the switch.

® The lamp is positioned at the (& r

end of the switch portion. Pull w out the lamp straight without turning it.

FIG. 13 b

Page 106

Cold-Cathode Tubes of Rear Cabinet

The Rear Cabinet is equipped with two Cold-Cathode Tubes, each of which is located on the lamp unit to the left or right of the coin chute door. To replace a Cold-Cathode Tube, remove the lamp unit from the Rear Cabinet. ® Turn off power.

@) Remove the 2 truss screw and then Lamp Sash Upper.

LAMP SASH UPPE!

TRUSS SCREW (2), black M4x8 PHOTO 13 j

@Remove the 2 truss screw and then Lamp Sash Lower.

LAMP SASH LOWER

TRUSS SCREW (2), black M4X8 PHOTO 13 k

Page 107

@Remove the lamp panel by pulling it out

downward. The panel is plastic. Pay attention to that applying load carelessly to it may cause it to break.

PHOTO 131

SCREW (4), black M4 X 10, w/flat & spring washers

PHOTO 13m

Page 108

© With the lamp unit tilted, pull out

the inside connector.

@ Remove the lamp unit from the

Rear Cabinet.

Disconnect the connector,

PHOTO 13 n

(8) Unfasten the wire that is from the

Cold-Cathode Tube. Then, pull out the connector connected to the Inverter BD.

Disconnect the connector.

Remove the flange nut securing each of the flange nuts to the left and right of the Cold-Cathode Tube.

FLANGE NUT (one each) PHOTO 130

PHOTO 13 p

Page 109

(Remove the Cold-Cathode Tube

from the lamp unit, and replace it with a new one.

COLD-CATHODE TUBE 390-6697-BL

Xx

PHOTO 13 q Cold-Cathode Tube Inverter BD

Any trouble of turning on/off a Cold-Cathode Tube may be due to breakage of the Inverter BD for the Cold-Cathode Tubes as well as the end of the safe useful life or failure of the lamp unit itself. On its backside, the lamp unit is equipped with the Inverter BD for the respective Cold- Cathode Tubes.

Remove the lamp unit by using the same procedure that was used to replace the Cold-Cathode Tube.

Q@nfasten the wire connected to the

Inverter BD. Then, pull out the connectors each located at either side of the BD.

Disconnect the connector.

INVERTER BRACKET PHOTO 13r

® Remove from the lamp unit the

inverter bracket on which the Inverter BD is placed. Remove the 4 securing screws.

SCREW (4)

M4 X 8, wflat & spring washers

PHOTO 13s

Page 110

@ Remove the Inverter BD from the INVERTER BD

inverter bracket, and replace it 838-14010-01 with a new one. Remove the 2 securing screws.

PHOTO 13t

Page 111
  • PERIODIC INSPECTION TABLE

The items listed below require periodic check and maintenance to retain the performance of this machine and to ensure safe business operation.

@ Be sure to check once a year to see if Power Cords are damaged, the plug is securely inserted, dust is accumulated between the Socket Outlet and the W Gi! Power Plug, etc. Using the product with dust as is accumulated can cause fire : and electric shock hazards. Periodically once a year, request the place of contact herein stated or the Distributor, etc. where the product was purchased from, as regards the internal cleaning. Using the product with dust as is accumulated in the interior

without cleaning can cause a fire or accident. Note that cleaning the interior

parts can be performed on a pay-bas

TABLE 14

ITEMSDESCRIPTIONPERIODREFERENCE
CABINETEnsure that Adjusters are in contact with the floor.|/Before

commencing 3 Check hazard preventive parts. daily operation.

SKATE BOARDCheck the Volume and Sensor.Monthly9

(Controller Board)

Greasing the swing bearingMonthly10-3
Greasing the Volume Control gears,Trimonthly10-3

crank sliding portion, and pinion gears

PROJECTORSCREEN cleaning.Weeklyll
Check adjustments.Monthly6,9, 11
COIN CHUTE DOORCoin insertion testMonthly12
CleaningTrimonthly12

GAME BD MEMORY TEST Monthly 9

Setting check

ITERIORCleaningAnnuallySee above.

POWER PLUG Inspection and cleaning

CABINET SURFACECleaningAs necessarySee below.

CLEANING THE CABINET SURFACES

When the cabinet surfaces are badly soiled, remove stains with a soft cloth dipped in water or diluted (with water) chemical detergent and squeezed dry. To avoid damaging surface finish, do not use such solvents as thinner, benzine, etc. other than ethyl alcohol, or abrasives, bleaching agent and chemical dustcloth.

Page 112
  • TROUBLESHOOTING

@ norder to prevent electric shock and short circuit, be sure to turn power off before performing work.

WARNING! @ Be careful so as not to damage wirings. Damaged wiring can cause electric shock or short circuit. @ After removing the cause of the functioning of the Circuit Protector, reinstate

the Circuit Protector. Depending on the cause of the functioning, using the

Circuit Protector as is without removing the cause can cause generation of heat and fire hazard.

In case a problem occurs, first check wiring connector connections.

15-1 TABLE OF TROUBLESHOOTING

TABLE 15a

PROBLEMS CAUSE COUNTERMEASURES

When the main SW_| The power is not ON. Firmly insert the plug into the outlet. is turned ON, the machine Incorrect power source/voltage. Make sure that the power supply/voltage are is not activated. correct.

The CIRCUIT PROTECTOR functioned Remove the cause of overload to reset the circuit due to momentary overcurrent. protector (see Sec. 6 / FIG. 15. 1).

CIRCUIT PROTECTOR CIRCUIT PROTECTOR

Functions due to the activation of bimetal. To restore the function, wait for approximately one minute or longer until the bimetal cools off. (Press the Button.)

FIG. 15.1

Page 113

TABLE 15 b

PROBLEMS CAUSE COUNTERMEASURES

Although sound is emitted, PTV screen is blackened and Fluorescent lamp does not light up. Poor connection of connector between Front Cabinet and PTV. Check for connection of 3p white connector (see Sec. 6).

The color on the PTV screen is not correct. Poor connection of connector between Front Cabinet and PTV.

Screen adjustment is not appropriate.

Check if R. G. B. and SYNC Connectors are

correctly connected (see Sec. 6).

Make adjustment appropriately (see Sec. 11).

PTV screen has a color deviation. Affected by the periphery, such as other machines, location building's steel frames, ete. Make convergence adjustments (see Sec. 11).

Change installation direction/ position. Move the other machines which cause the problem.

Foot Controller operation is Poor V. R. setting. Perform V. R. setting (see Sec. 9).

unsatisfactory. V.R. deviation or malfunctioning. Adjust or replace the V. R. (see Sec. 10).

Poor mesh of GEAR. Adjust GEAR mesh (see Sec. 10).

Can not be Connection fault of connector between Accurately connect the connector. unlocked. Front & Rear Cabinets.

Irregular sound emitted from inside of Rear Cabinet. Greasing to gear mesh portion is not satisfactory, or extraneous matter mixed in. Apply greasing or eliminate extraneous matter (see Sec. 10).

Fluorescent Lamp does not light up. Poor connection of connector in the Billboard.

Fluorescent lamp need replacement. Accurately connect the Connector (see Sec. 6).

Replace Fluorescent Lamp (see Sec. 13).

The Cold-Cathode Tube does not blink normally. Connection fault of connector between Front & Rear Cabinets.

Cold-Cathode Tube need replacement.

Failure of Inverter BD. Accurately connect the connector (see Sec. 6).

Replace the Cold-Cathode Tube (see Sec. 13). 390-6697-BL

Replace the Inverter BD (see Sec. 13). 838-14010-01

Sound is not emitted. Poor connection of connector between Front Cabinet and Rear Base.

Sound volume is incorrect. Accurately connect the connector (see Sec. 6).

Adjust the Sound Volume Adjustment V. R. of the SW Unit (see Sec. 9).

Page 114

15 - 2 SYSTEM ERROR MESSAGES

When you have connected the power or exited the GAME TEST MODE screen, the system may display an error message as listed below, if: + A system-related failure is detected, or + A setting does not conform to the specifications of the product. If this is the case, you cannot play the game.

ERROR 1 Main board's serial ID is incorrect or unrecognizable. For repairing, ship it to a distributor from which you purchased the product.

ERROR 2 ROM board's serial ID is incorrect or unrecognizable. For repairing, ship it to a distributor from which you purchased the product.

ERROR 3 Serial ID cannot be set correctly on the main board. Reset the system by disconnecting and reconnecting the power. If the problem is still reproduced, ship it to a distributor, for repairing, from which you purchased the product.

ERROR 4 Monitor type is set incorrectly. Open the SYSTEM ASSIGNMENTS screen, select the MONITOR TYPE item, and reset it correctly.

ERROR 5 Display mode is set incorrectly. Open the SYSTEM ASSIGNMENTS screen, select the DISPLAY MODE item, and reset it correctly.

ERROR 6 Area code is not compatible between the main board and the game software saved in the ROM board. You cannot solve the problem by resetting.

ERROR 7 Cabinet type is set incorrectly. Open the SYSTEM ASSIGNMENTS screen, select the CABINET TYPE item, and reset it correctly.

ERROR 8 Jumper is set incorrectly on the ROM board. For repairing, ship it to a distributor from which you purchased the product.

Usually, no error message is displayed except a setting error on the SYSTEM MENU screen. System error may occur when you have replaced a system-related part (game board etc.) with the one used by other games.

Page 115
  • GAME BOARD

AY @ !n order to prevent electric shock and short circuit hazards, be sure to turn power off before performing work.

WARNING! @ Be careful so as not to damage wirings. Damaged wiring can cause fire, electric shock and short circuit hazards. @ Do not expose the Game BD, etc. without a good reason. Failure to observe this can cause electric shock hazard or malfunctioning.

electricity. Before performing IC Board related work, be sure to discharge /\ The electronic parts on the IC Board could be damaged due to human body's static

CAUTION! physically accumulated statics by touching grounded metallic surfaces, etc.

Put the Game Board in the Carton Box (an accessory) together with the Shield Case when requesting for the replacement or repair. Transporting the Game Board in an undesignated status for replacement/repair is unacceptable. In this manual, how to remove the Game Board is explained for convenience. However, this work should be performed by SEGA SERVICEMAN.

IMPORTANT

16 - 1 REMOVING THE GAME BOARD

The Game Board and all the other IC boards are located on the back of the Front Cabinet.

@tun off power.

@ Remove the 2 truss screws securing the Back Door.

TRUSS SCREW (2), black M4 X 20

PHOTO 16. 1a

Page 116

® Unlock and remove the Back Door. The Game Board is located in the shield case inside the door. Take off 3 screws to remove Shield Case Lid, and the Game Board appears. This work should never be performed by those other than Sega Serviceman.

Unlock.

/SHIELD CASE

PHOTO 16. 1c

PHOTO 16. 1b

@Disconnect all connectors connecting to the Filter Board of Shield Case.

Take off 4 screws which secure the Shield Case to the Base (wooden base) and take out Shield Case from the Cabinet. Disconnect all of

  • Take off 2 screws for each the wiring connectors. and remove 2 Shield Case Brackets from the Shield Case. Pack up the Shield Case with packing materials, put it into a carton box, and request service. SCREW (3) MAX 8, wiflat & spring washers

SHIELD CASE BRACKET SHIELD CASE LID

FIG. 16.1 _~ SCREW oo” M4 X 16, w/flat & spring washers

Page 117

16 - 2 COMPOSITION OF GAME BOARD

GAME BD ATR (833-14150)

SCREW (5) MB X 50, w/flat & spring washers \

FLANGE NUT (8) M3, plastic washer used.

SAMURAI EXTEND SOUND BOARD 837-13629 ROM BD ATR 834-14149 MAIN BD SEGA HIKARU 834-13821-01

BD TRAY FOR SEGA HIKARU 105-5380

FIG. 16.2

ROM BD MAIN BD JUMPER SETTING JUMPER SETTING

JP3.2-3JPp41-2
JP42-3JP51-2
JP52-3JP61-2
JP6—2-3JP71-2

JP8 = 2-3 JP9 2-3 JP10 1-2 JP11 2-3

Page 118
  • DESIGN RELATED PARTS For the Warning Display stickers, refer to Section 1.

G-LOLe-ulv GuVvVOESLVMS YSMOILS g-LOLE-aLV Vv LVW di1S NON O-LOLE-YLV ‘@ LVW di1S NON

S-LLLE-aLv 4 di 318VL YayoILs d-60LE-YLV 101 318VL YayolLs 9-€92€-ULW YSLV1d NUNL YaMOLLS Ovoe-aLW g-€928-ULV SSAYdGV YAMOILS BLV1d NUNL YaMOLLS. 2000-YLV d3LS YSMOILS,

  • a-208-ULV

¥ GYVO JdIs YSHOLLS 3aIS : g-€208-ULV

7] GuvO8g JdIs YSNOILS als 6E0E-YLV UY SWVes YV3Y YSHOILS S8E0E-YLV TAWVas YV3Y YSHOILS ‘g-veOe-Y LV uvay YOOT1S YAMOILS g-€€0E-aLV ANOUS YOOTS YSMOILS

OZ0E-YLV TANVd dAVT iy wa

Lo-zo00-4Lv SNA ULV HS YLSNI AW1d Loze-ULv —

ALV1d MS wa

  • Z1ZL-ULV 4 YAGIS Ald YANOLLS 10-£000-4LV - LIZL-aLv DNA dOd 3aIs ————_ >» ea 73dIS Ald YSMOLLS set ~\ v2zl-ULy GuVOSTIE YSHOILS PxT2er 357174 ALW1d YO1OD LezL-ULv SLvid duvog T1198
Page 119
  • PARTS LIST

©@ rop assy ATR

  • )arr-1000 ASSY FRONT CABI

L- Q)arr-1200 ASSY PTV

L @)arr-1300 ASSY FRONT PANEL

L- @arr-3000 ASSY REAR CABI

L_ @arr-3700 ASSY SW PANEL

  • Qarr-1001 ASSY SUBCABI FRONT

L— @).arR-4000 ASSY MAIN BD

L— @3 uzev-4200 ASSY TRANS EXP

\_ @ urv-4210 ASSY TRANS EXP 200V

———. @ arr-1210 PIV W/STICKER ATR

L- @xez-1150 ASSY MASK

L_ @arr-1220 ASSY BILLBOARD

  • @arr-3100 ASSY MECHA

L— @)arr-3500 ASSY TOWER

L— @.arr-3600 LAMP UNIT

L_ @arr-6002 ASSY WIRE REAR CABI Q@arr-1050 AC UNIT

t— (G)arr-1060 FAN UNIT

@ arr-1070 ASSY BACK DOOR

@jarr-6001 ASSY WIRE FRONT CAB1

@3arr-4050 ASSY SHIELD CASE ATK

LINES

  • ©) arR-3150 ASSY BOARD

-— @3arr-3200 ASSY ROLLING BASE

t— Go arr-3250 ASSY SWING MECHA

  • ©}. arr-3300 YAWING SENSOR UNIT

L_ @Y arr-3350 BRAKE UNIT

  • 2) rwy-1180 SW UNIT

L_ @) arr-3550 METER UNIT

Page 120

C) Top Assy ATR ‘ (p-1/2)

Page 121

C) Top assy ATR

ITEM NO.

Gow sauaene PART NO.

ATR-1000 ATR-1200 ATR-1300 ATR-3000 ATR-3700 ATR-0001 ATR-0002-01 421-7308- ~ 421-8479-01 SGM-4306 SGM-4469 ATR-0003-01 440-WS0002XEG 440-WS0033XEG 440-CS0231-EG 440-CS0122-EG 440-WS0143-EG 440-CS0175-EG 440-CS0232-EG 440-CS0233-EG 440-CS0234-EG ATR-0007

000-T00520-0B 068-552016-0B 000-T00410-0C 000-P00410-WB 000-T00420-0B 050-H00400 060-S00400 060-F00400

ATR-60030

601-6604-70 SGM-2675 420-6614-01 600-6664-02

390-5160 600-6729 600-6619 600-6618 600-6695 SGM-4111 220-5576 280-5009-01 220-5484 540-0064 090-0275

105-5356 421-8740 421-6690-03 421-6690-06 421-6690-01 421-6119-91 421-6120-92 (D-2/2)

DESCRIPTION NOTE

ASSY FRONT CABI ASSY PTV ASSY FRONT PANEL ASSY REAR CABI ASSY SW PANEL HOLE LID PLAY INSTR SH ATR ENG DENOMI SH 1GAME ~ STICKER INSTR SUNLIGHT ENG POLYE COVER 1100 X 1200 X 1000 POLY COVER 1000 X 1700 X 1100 SIDE POP ENG STICKER W POWER OFF ENG. STICKER W BD POWER OFF ENG STICKER C PANEL ATR ENG STICKER C FENCE ENG STICKER W POWER OFF WIDE ENG STICKER C EPILEPSY ENG STICKER C ATR A ENG STICKER C ATR B ENG STICKER C STEP ATR ENG STICKER STEP

M SCR TH BLK MS X 20 FLT WSHR BLK 5.5-20 X 1.6 M SCR TH CRM M4 X 10 M SCR PH BLK W/FS M4 X 10 M SCR TH BLK M4 X 20 HEX NUT M4 SPR WSHR M4 FLT WSHR M4

WH DC TUBE

CARTON BOX 70 POLYETHYLENE BAG 240 X 370 OWNERS MNL ATR ENG WIRE HARN EARTH W/LUG M6 TAIWAN NOT USED OTHERS LAMP WG B TYPE 6V 3W (C2R) AC CABLE CONNECT TYPE 154A TAIWAN AC CABLE CONNECT TYPE FOR UK ~=HONG KONG AC CABLE CONNECT TYPE FOR EXP = AC 220 ~ 240V AREA AC CABLE CONNECT TYPE USA ISA USA KEY BAG KEY MASTER FOR 220-5575 CORD CLAMP 21 VOL CONT B-SK OHM GREASE GUN KH-120 GREASE ALBANIA EP-1 400G

SHIPPING BRKT

CAUTION INSTR COP U/R STICKER 220V AC 220V AREA STICKER 110V AC 110V AREA STICKER 120V AC 120V AREA STICKER FCC USA STICKER SEGA USA
Page 122
  • ASSY FRONT CABI (ATR-1000) (D-1/2)
Page 123
  • ASSY FRONT CABI (ATR-1000) (D-2/2)
ITEM NO.PART NO.DESCRIPTIONNOTE
1ATR-1001ASSY SUBCABI FRONT

ATR-4000 ASSY MAIN BD

3421-8885STICKER CAUTION FORK.
201000-P00530-SMSCR PH WIS MS X 30
202068-552016FLT WSHR 5.5-20 X 1.6
/000-P00630M SCR PH M6 X 30
/068-652016FLT WSHR 6.5-20 X 1.6
/060-S00600SPR WSHR M6
/JEY-4210ASSY TRANS EXP 200V LINESAC 220 ~ 240V AREA
/JEY-4200ASSY TRANS EXPAC 110 ~ 120V AREA
Page 124

G) ASSY SUBCABI FRONT (ATR-1001) (D-1/2)

Page 125
  • ASSY SUBCABI FRONT (ATR-1001) (D-2/2)

ITEM NO.

CHOIDARWNHE PART NO.

ATR-1002 ASK-1152 ARC-1006 117-5233 ATR-1050 ATR-1060 ATR-1070 253-5460-01 117-5402-06-91

601-9377 601-5699X 280-5009-01

000-P00416-W 030-000630-SB 000-T00416-0B 000-T00420-0B 011-F00316 060-F00600 050-H01600-0B 011-F00316

ATR-6001 ATR-60021 ATR-60022X 600-7232-1200 600-7009-2500 DESCRIPTION

FRONT CABI LOCK BRKT LEG BRACKET PLATE LEG BRACKET BLACK AC UNIT FAN UNIT ASSY BACK DOOR AIR VENT BLACK EARTH TERMINAL PLATE 6P.

CASTER FAI=75 LEG ADJUSTER BOLT M16 X 75 CORD CLAMP 21

M SCR PH WIFS M4 X 16 HEX BLT BLK W/S M6 X 30 M SCR TH BLK M4 X 16 M SCR TH BLK M4 X 20 TAP SCR FH 3 X 16 FLT WSHR M6 HEX NUT BLK M16 TAP SCR FH 3 X 16

ASSY WIRE FRONT CABI WH AC OUT XFMR WH EXT AC WH EARTH VD1.25-4 1200MM ASSY RGB CA D-SUB 15P 2500MM

Page 126

G) AC UNIT (ATR-1050) (D-1/2)

Page 127

G) AC UNIT (ATR-1050)

ITEM NO.

RON PART NO.

JBA-1031 DYN-0402 421-8202 421-7468-01

214-0202 512-5046-8000 512-5046-5000 450-5126 450-5134 450-5133 450-5135 509-5453-91-V-B 270-5115 280-0417

310-5029-K20 280-0419 601-0460

000-P00416-WB 000-P00408-WB 012-P00408 060-F00400 060-S00400 050-H00400

JBA-60001 JBA-60002 JBA-60003 ATR-60100 JBA-60037 600-7232-0350 (D-2/2)

DESCRIPTION NOTE

AC BRKT NOISE FILTER BASE STICKER EARTH MARK STICKER C.P W/PIC

AC INLET PANEL TYPE C.P 8000MA CE UL AC 110 ~ 120V AREA C.P 5000MA CE UL AC 220 ~ 240V AREA MAGNET CONTACT S-NIOCX TAIWAN MAGNET CONTACT S-NIOCX AC 230V OTHERS MAGNET CONTACT S-NIOCX AC200V KOREA MAGNET CONTACT S-NIOCX AC120V USA SW ROCKER J8 V-B NOISE FILTER 15A GT-215J TERMINAL BINDING POST BLACK TAIWAN NOT USED OTHERS SUMITUBE F K 20MM HARNESS LUG PLASTIC TIE BELT 100MM

M SCR PH W/FS BLK M4 X 16 M SCR PH WI/FS BLK M4 X 8 TAP SCR #2 PH4 X 8 FLT WSHR M4 SPR WSHR M4 HEX NUT M4

WIRE HARN AC UNIT IN WIRE HARN MAIN SW. WIRE HARN M.CONTACT & N.FILTER WH AC UNIT OUT WIRE HARN EARTH INLET WH EARTH VD1.25-4 350MM

Page 128

(S) FAN UNIT (ATR-1060)

i G) a ZA,

CONNECTOR

ITEM NO. PART NO. DESCRIPTION

1ATR-1061FAN BRKT
101260-0011-02AXIAL FLOW FAN AC100V 50-60HZ
102601-8543FAN GUARD
201000-P00312-WM SCR PH W/FS M3 X 12
Page 129
  • ASSY BACK DOOR (ATR-1070)

ITEM NO. PART NO.

ATR-1071 TH-1015 253-5460-01

220-5575

000-T00408-0B DESCRIPTION

BACK DOOR LOCKING TONGUE AIR VENT BLACK

CAM LOCK MASTER W/O KEY

M SCR TH BLK M4 X 8

Page 130

@) ASSY PTV (ATR-1200)

ITEM NO. PART NO. DESCRIPTION

1ATR-1210PTV W/STICKER ATR
2MGL-1150ASSY MASK
3ATR-1220ASSY BILLBOARD

4 RAL-0501 MASK HOLDER

5DYN-0501PANEL MOUNT BRKT L
6DYN-0502PANEL MOUNT BRKT R
201000-T00525-0BM SCR TH BLK MS X 25
202068-552016-0BFLT WSHR BLK 5.5-20 X 1.6
203000-P00520-WBM SCR PH W/FS BLK MS X 20
204000-T00540-0CM SCR TH CRM MS X 40
205000-F00412M SCR FH M4 X 12
Page 131
  • PTV W/STICKER ATR (ATR-1210)

ITEM NO. PART NO.

ATR-1211 ATR-1212

200-5788-31 200-5799-31 DESCRIPTION

STICKER PTV SIDE L STICKER PTV SIDER

PROJECTION DSPL T SOTYPE 31K PROJECTION DSPL M SOTYPE 31K

Page 132

Q@) ASSY MASK (MGL-1150)

ITEM NO. PART NO. DESCRIPTION

1MGL-1102TV MASK
2MGL-1151SLIT PLATE
3MGL-1152MASK SIDE HOLDER
201012-F00408-0BTAP SCR FH BLK 4 X 8
202000-F00410M SCR FH M4 X 10
Page 133

(D-1/2)

ASSY BILLBOARD (ATR-1220)

Page 134

ASSY BILLBOARD (ATR-1220) (D-2/2)

ITEM NO.PART NO.DESCRIPTIONNOTE
1ATR-1221BILLBOARD BASE
2ATR-1222BACK PANEL
3ATR-1223BILLBOARD PIPE
4ATR-1224COLOR PLATE
5ATR-1225HOLDER L
6ATR-1226HOLDER R
7ATR-1227PLATE SASH
8ATR-1228FL COVER PLATE
9ATR-1229ACRYL HOLDER
10ATR-1230SLIM COVER
llATR-1231BILLBOARD PLATE
12ATR-1232PLATE HOLDER
13ATR-1233WIRE COVER L
14ATR-1234WIRE COVER R
15ATR-1235BALLAST BASE
16ATR-1236BILLBOARD LID
17ATR-1237HOLE LID
18ATR-1238STICKER BILLBOARD
19253-5460-01AIR VENT BLACK
20253-5457FL HOLDEROTHERS

Locally supplied. USA

21421-7501-18STICKER FL32WOTHERS

Locally supplied. USA

22440-WS0027-EGSTICKER W HIGH TEMP WIDE ENG
23440-WS0143-EGSTICKER W POWER OFF WIDE ENG
101LOC. PURCHASE36” FL. LIGHT FIXTURE
102LOC. PURCHASE36” FL. LAMP
103182-5078-ABCOIL BALLAST AB-116OTHERS

Locally supplied. USA

104214-0223-03FL SOCKET W/CONNOTHERS

Locally supplied. USA

105280-5009-01CORD CLAMP 21
106280-5275-SR10CORD CLAMP SR10
201000-P00540-0CM SCR PH CRM MS X 40
202050-F00400FLG NUT M4
203000-T00412-0CM SCR TH CRM M4 X 12
204050-U00400U NUT M4
205060-F00400FLT WSHR M4
206000-T00408-0CM SCR TH CRM M4 X8
207031-000414-0CCRG BLT CRM M4 X 14
208050-F00500FLG NUT M5
209068-552016FLT WSHR 5.5-20 X 1.6
210000-T00408-0BM SCR TH BLK M4 X 8
211000-P00430-SM SCR PH W/S M4 X 30OTHERS

Locally supplied. USA

212068-441616FLT WSHR 4.4-16 X 1.6OTHERS

Locally supplied. USA

213000-P00412-WM SCR PH W/FS M4 X 12OTHERS

Locally supplied. USA

214000-P00408-WM SCR PH W/FS M4 X 8OTHERS

Locally supplied. USA

215011-F03516TAP SCR FH 3.5 X 16
301ATR-60091WH SLIM INV
302ATR-60092WH SLIM
303ATR-60093WH FL
Page 135
  • ASSY FRONT PANEL (ATR-1300) (D-1/2)
Page 136
  • ASSY FRONT PANEL (ATR-1300) (D-2/2)

ITEM NO.

AuWhRWNH PART NO.

ATR-1301 ATR-1302 EZT-0603 EZT-0604 ATR-1303 440-WS0002XEG

000-T00420-0B 068-441616-0B 050-F00500 068-552016 DESCRIPTION

FRONT PANEL, FRONT LID SIDE BRKT BRKT UPPER BRKT LOWER STICKER W POWER OFF ENG

M SCR TH BLK M4 X 20 FLT WSHR BLK 4.4-16 X 1.6 FLG NUT M5 FLT WSRR 5.5-20 X 1.6

Page 137
  • ASSY REAR CABI (ATR-3000) (D-1/3)

eS zssaz ss qe

SCREW FAS

f)

BOTH SIDES @)

Page 138
  • ASSY REAR CABI (ATR-3000) (D-2/3)

ITEM NO.

CoOIDAHAARWNHY PART NO.

ATR-3100 ATR-3500 ATR-3600 ATR-3001 ATR-3002 ATR-3003 ATR-3004 ATR-3005 ATR-3006 ATR-3007 ATR-3008 ATR-3009 ATR-3010 ATR-3011 ATR-3012 ATR-3013 ATR-3014 ATR-3015 ATR-3016 ATR-3017 ATR-3018 ATR-3019 ATR-3020 ATR-3021 ATR-3022 ATR-3023 ATR-3024 ATR-3025 ATR-3026 ATR-3027 ATR-3028 ATR-3029 ATR-3030 ATR-3031 ATR-3032 ATR-3033 ATR-3034 ATR-3035 ATR-3036 ATR-3037 ATR-3038 ATR-3039 421-8885

130-5228 130-5097 280-5009-01 209-0023 601-0460 DESCRIPTION NOTE

ASSY MECHA ASSY TOWER LAMP UNIT REAR FRAME SUPPORT PIPE PIPE HOLDER FRONT A PIPE HOLDER FRONT B PIPE HOLDER SIDE STAND PIPE PIPE HOLDER REAR PIPE SUPPORT BRKT STEP BRKT PIPE LIDL PIPE LIDR INNER BOARD L INNER BOARD R SPEAKER HOLDER CNT PANEL STAY L STAYR TOWER BRKT BASS BRKT LAMP PANEL LAMP SASH UPPER LAMP SASH LOWER SIDE BOARD L SIDE BOARD R SIDE PIPE L SIDE PIPE R SIDE PIPE HOLDER L SIDE PIPE HOLDER R. SIDE GUARD PANEL SIDE PANEL HOLDER SIDE PIPE BRKT A SIDE PIPE BRKT B FLOOR BOARD FRONT FLOOR BOARD REAR FLOOR BRKT WOOFER HOLDER LID REAR STICKER REAR FRAME L STICKER REAR FRAME R STICKER CAUTION FORK

SPEAKER BOX 40HM 40W SPEAKER BOX SUPER WOOFER CORD CLAMP 21 CONN CLOSED END. PLASTIC TIE BELT 100MM

Page 139
  • ASSY REAR CABI (ATR-3000) (D-3/3)

ITEM NO. PART NO.

030-001025-S 068-A52820 030-000820-SB 060-F00800-0B 000-P00410-WB 030-000840-SB 030-000860-SB 031-000650-0C 059-0083 060-F00600-0B 000-T00408-0C 000-P00516-W 030-000616-SB 050-U00500 060-F00S00 050-U00400 060-F00400 000-T00408-0B 030-000630-SB 068-652016-0B 030-000635-SB 000-T00412-0B 050-C00400-3B 000-T00620-0C 059-0082 069-0140 000-T00425-0B 068-441616-0B 012-P00512-0B 008-T00412-0B

ATR-6002 ATR-60081 DESCRIPTION

HEX BLT W/S M10 X 25 FLT WSHR 10.5-28 X 2 HEX BLT W/S BLK M8 X 20 FLT WSHR BLK M8 M SCR PH BLK W/FS M4 X 10 HEX BLT W/S BLK M8 X 40 HEX BLT W/S BLK M8 X 60 CRG BLT CRM M6 X 50 CAP NUT TYPE 3 BLK M6 FLT WSHR BLK M6 M SCR TH CRM M4 X 8 M SCR PH W/FS MS X16 HEX BLT W/S BLK M6 X 16 U NUT MS FLT WSHR M5 U NUT M4 FLT WSHR M4 M SCR TH BLK M4 X 8 HEX BLT BLK W/S M6 X 30 FLT WSHR BLK 6.5-20 X 1.6 HEX BLT BLK M6 X 35 M SCR TH BLK M4 X 12 CAP NUT TYPE3 BLK M4

M SCR TH CRM M6 X 20

CUP NUT TYPE 3 CRM M6 FLT WSHR NI M6 M SCR TH BLK M4 X 25 FLT WSHR BLK 4.4-16 X 1.6 TAP SCR #2 PH BLK 5 X 12 TMP PRF SCR TH BLK M4 X 12

ASSY WIRE REAR CABI WH WOOFER

Page 140
  • ASSY MECHA (ATR-3100) (D-1/2)
Page 141
  • ASSY MECHA (ATR-3100)

ITEM NO. PART NO.

1 ATR-3150 2 ATR-3200 3 ATR-3250 4 ATR-3300 5 ATR-3350 6 ATR-3101 7 ATR-3102 8 ATR-3103 9 ATR-3104 10 ASL-3105 11 ASL-3106 12 ATR-3107 13 ATR-3108 14 ATR-3109-A 15 ATR-3110 16 ATR-3109-B 17 ATR-3111-B

101 100-5302 102 280-5009-01 103 280-5275-SR10 104 601-0460

201 030-000816-S 202 030-0008 16-W 203 000-P00408-W 204 030-000825-S 205 031-000620-0B 206 060-F00600 207 060-S00600 208 050-H00600 209 000-T00410-0B 210 000-P00412-WB 2u1 FAS-200014 212 020-000825-0Z 213 060-S00800 214 050-H00800 215 050-H00400 216 000-P00410-W 217 068-852216 218 060-F00400 219 060-S00400 220 000-P00408 221 000-P00420-WB 222 DYN-1019

301 ATR-60051 302 ATR-60052 303 ATR-60053X 306 ATR-60103 (D-2/2)

DESCRIPTION NOTE

ASSY BOARD ASSY ROLLING BASE ASSY SWING MECHA YAWING SENSOR UNIT BRAKE UNIT BOARD BELLOWS SIDE BELLOWS BRKT BELLOWS HOLDER HOOK STOPPER UPPER HOLDER SIDE BELLOWS SASH END BELLOWS SASH TABLE LID BLANK BELLOWS END BRKT STICKER TABLE LID L STICKER TABLE LIDR

BEARING 15 CORD CLAMP 21 CORD CLAMP SR10 PLASTIC TIE BELT 100MM

HEX BLT W/S M8 X 16 HEX BLT W/FS M8 X 16 M SCR PH W/FS M4 X 8 HEX BLT W/S M8 X 25 CRG BLT BLK M6 X 20 FLT WSHR M6 SPR WSHR M6 HEX NUT M6 M SCR TH BLK M4 X 10 M SCR PH W/FS BLK M4 X 12 HEX SKT H CAP SCR BLK OZ M8 X 45 HEX SKT H CAP SCR BLK 0Z M8 X 25 SPR WSHR M8 HEX NUT M8 HEX NUT M4 MSCR PH W/FS M4 X 10 FLT WSHR 8.5-22 X 1.6 FLT WSHR M4 SPR WSHR M4 M SCR PH M4 X 8 M SCR PH WIFS BLK M4 X 20 FLT WASHER M8

WH BOARD WH BRAKE WH EXT SWING VOL WH EARTH BOARD TUBE

Page 142

(D-1/2)

ASSY BOARD (ATR-3150)

(wo- 4649) WNO'O :LAN EW (WO J0>4Z) WNZ'O EW

‘T]OM se (Satossao0R) LONOW (wo-JO481) WNOZ) YN Suns yi « ;

Uy} Sursn synu a}qnop osn [[ejsurt Of, (wo- JOGO) WNEOL “SW @) (€0H) (WO {040,Z) WNG'OZ BW AA OL ANOWOL ONINALSWA MANOS

Page 143

ASSY BOARD (ATR-3150)

ITEM NO. PART NO.

1 ATR-3151 2 ATR-3152 3 ASL-3153 4 ATR-3154 5 ATR-3155 6 ATR-3156 7 ATR-3157

101 370-5232-01 102 100-5302 103 601-5564 104 280-5275-SR10 105 280-5207

201 000-P00308-W 202 000-P00408-W 203 000-P00314-S 204 030-0008 16-S 205 068-852216 206 020-000820-OZ 207 250-5421 208 050-H00300 209 060-S00800

301 ATR-60061 (D-2/2)

DESCRIPTION

BOARD BASE UPPER BASE SW PLATE A SW PLATE B STOPPER B STOPPER BRKT B WIRE COVER

PHOTO SENSOR OMT-01L-SS BEARING 15 STOPPER CORD CLAMP SR10 HARNESS LUG CC-1005

MSCR PH W/FS M3 X 8 MSCR PH W/FS M4 X 8 MSCR PH WIS M3 X 14 HEX BLT W/S M8 X 16 FLT WSHR 8.5-22 X 1.6 HEX SKT H CAP SCR BLK OZ M8 X 20 FLT WSHR 3.5-12 T=1.0 HEX NUT M3 SPR WSHR M8

WH PHOT FRONT

Page 144

@ e@|_-le in © ——

(5) ASSY ROLLING BASE (ATR-3200)

i ; _ 2.45Nm (25kgf cm) 1.76Nm (18kgf cm) M4 NUT: 1.47Nm (15kgf «cm) M3: 0.2Nm (2kgf + cm) M3 NUT: 0.6Nm (6kgf - cm)

To instal 103) , use double nuts using the

M6NUT (accessories) as well. (D-1/2)

Page 145
  • ASSY ROLLING BASE (ATR-3200) (D-2/2)

ITEM NO.

DCIDNRWNHH PART NO.

ATR-3201X ASL-3204 ATR-3205 ASL-3206X ASL-3207 ASL-3208 ATR-3209X ASL-3210

100-5018 601-9354 601-5564 100-5386 370-5232-01 280-5207 280-5288 280-6632

050-F00600 030-000616-S 060-F00600 000-P00408-W 030-000612-S 068-652016 050-F00400 050-H00600 000-P00510-W 000-P00314-S 060-S00300 000-P00308-W 250-5421 050-H00300

ATR-60062 600-6897-073 DESCRIPTION

ROLLING BASE UPPER ROSTA HOLDER ROSTA ARM HOLDER UPPER STOPPER UPPER STOPPER A STOPPER BRKT A SWING STOPPER RUBBER

BEARING BALL 8 ROSTA STOPPER BEARING 10 PHOTO SENSOR OMT-01L-SS HARNESS LUG CC-1005 HARNESS LUG CC-1003 CORD CLAMP MSC-2

FLG NUT M6 HEX BLT W/S M6 X 16 FLT WSHR M6 MSCR PH W/FS M4 X 8 HEX BLT W/S M6 X 12 FLT WSHR 6.5-20 X 1.6 FLG NUT M4 HEX NUT M6 M SCR PH WIFS MS X 10 MSCR PH WIS M3 X 14 SPR WSHR M3 MSCR PH W/FS M3 X 8 FLT WSHR 3.5-12 T=1.0 HEX NUT M3

WH PHOT REAR WIRE HARN FRONT SENSOR,

Page 146
  • ASSY SWING MECHA (ATR-3250) (D-1/3) Ee & ~ 2
ale| @=| @
elséS|
OyoSE| 2
prea prea#) 22) 2
ol Oyelera
x| x=) 3a
mysS| 2a) ot
LE| =z
7 5\54) 2Zz

Z y| &| = a oe HOE = a <=

es)

St)

& >

co

cs)

(<2) és) () 3) & @- ° a -) Q y -)

  • g-) (Ss)
Page 147

ASSY SWING MECHA (ATR-3250) (D-2/3)

ITEM NO. PART NO.

ASL-3251 ATR-3252 ATR-3253 ATR-3254X ATR-3255 ATR-3256 ATR-3257X ATR-3258 ATR-3259 ATR-3260X ATR-3261 ATR-3262 ATR-3263-A ATR-3264 ATR-3265 ATR-3266 ATR-3267 ATR-3268 ATR-3269 ATR-3270 ASL-3308 ATR-3271 ATR-3263-B ATR-3263-C ATR-3251

100-5388 601-11016 100-5387 601-8458 601-8596 100-5274 601-5564 601-11019 601-11005 220-5484 280-5008 280-5009-01 280-5169 280-5275-SR10 310-5029-F20 DESCRIPTION

MOUNT BLOCK STOP BASE SWING BASE MECHA BASE ROLL ROSTA HOLDER CENTERING CAM ROLL COLLAR ROLL SHAFT FOLLOWER COLLAR FOLLOWER SHAFT TABLE FRAME TURN TABLE TURN PLATE BLANK. ROLL VR HOLDER ROLL VR BRKT PIN GUIDE PIN CRANK ROLL PIN STOPPER BRKT L STOPPER BRKT R SPL WASHER M12 CENTERING FIXER STICKER TURN PLATE L STICKER TURN PLATE R MOUNT BLOCK ATR

TURN BEARING 336 ROSTA SE-27 ROLLER 15 ROSTA 22 DR-S27X100 ROSTA 22 BEARING 20 STOPPER SHOCK ABSORBER FK-2525-C-SE4 STOPPER RI-30HD VOL CONT B-SK OHM CORD CLAMP 15 CORD CLAMP 21 CORD CLAMP TL-20S CORD CLAMP SRI10 SUMITUBE F F 20MM

Page 148
  • ASSY SWING MECHA (ATR-3250) (D-3/3)

ITEM NO. PART NO.

050-H01200 060-S01200 FAS-300015 030-000820-S 060-F00800 030-000830-S 060-F01200 030-000850-S 031-000625-0B 060-F00600 060-S00600 050-H00600 000-P00408-W 000-P00418-W 050-H00400 028-C00306-P 060-F00300 065-E00200 030-000840-S FAS-290002 060-S01000 030-000625-S 068-652016 000-P00406-W 030-000870-S

ATR-60060 DESCRIPTION

HEX NUT M12 SPR WSHR M12 HEX BLT W/S M12 X 20 HEX BLT W/S M8 X 20 FLT WSHR M8 HEX BLT W/S M8 X 30 FLT WSHR M12 HEX BLT W/S M8 X 50 CRG BLT BLK M6 X 25 FLT WSHR M6 SPR WSHR M6 HEX NUT M6 M SCR PH W/FS M4 X 8 M SCR PH W/FS M4 X 18 HEX NUT M4 SET SCR CH CUP P M3 X 6 FLT WSHR M3 E RING 2MM HEX BLT W/S M8 X 40 HEX SKT SCR BH BLK M10 X 16 SPR WSHR M10 HEX BLT W/S M6 X 25 FLT WSHR 6.5-20 X 1.6 M SCR PH W/FS M4 X 6 HEX BLT W/S M8 X 70

WH ROLL VOL

Page 149

(1) YAWING SENSOR UNIT (ATR-3300)

Greasing the gears.

SCREW FASTENING TORQUE TO BE

1.76N -m(18kaf «cm) M4 SET SCR 2.45N -m(25kaf -cm) M3 SET SCR 1.27N -m(13kgf -cm)

ITEM NO. PART NO. DESCRIPTION

1ATR-3301YAW SENSE BOX
2ATR-3302REDUCTION SHAFT
3ATR-3303SHAFT HOLDER
4ATR-3304YAW VOL HOLDER
5ATR-3305GEAR 18 M2
6ATR-3306GEAR 15 M0.75
7ATR-3307KEY 2X2 X24
8601-6296-91GEAR 75B
103220-5484VOL CONT B-SK OHM
104280-0419HARNESS LUG
105310-5029-F20SUMITUBE F F 20MM
201000-P00408-WMSCR PH W/FS M4 X 8
202028-C00306-PSET SCR CH CUP P M3 X 6
203028-C00416-PSET SCR CH CUP P M4 X 16
301ATR-60050WH SWING VOL
Page 150
  • BRAKE UNIT (ATR-3350)

ITEM NO. PART NO.

1 ATR-3351 2 ASL-3352 3 ATR-3353 4 ASL-3354 5 ASK-3606

101 601-10806 102 100-5229

201 020-000530-0Z 202 060-S00500 203 065-S014S0-Z 204 065-A030H0-Z 205 028-A00408-P SCREW FASTENING TORQUE TO BE

Md:3.7Nm

M4:1.8Nm

DESCRIPTION

BRAKE BASE PINION GEAR 25 BRAKE SHAFT KEY 5X5 X 24 KEY 5 X 5-10.5

BRAKE BXH-08 BEARING 17

HEX SKT H CAP SCR BLK OZ MS X 30 SPR WSHR M5 STP RING BLK 0Z S14 STP RING BLK 0Z H30 SET SCR HEX SKT CUP P M4 X 8

Page 151

(D-1/2)

ASSY TOWER (ATR-3500)

SECTION A-A

Page 152
  • ASSY TOWER (ATR-3500)

ITEM NO.

RWNY PART NO.

ATR-3501 INY-1180 ATR-3550 105-5171 105-5172 DP-1167

421-7501-02

253-5366

220-5237-92- ~ 220-5482-91- ~

220-5575

220-5574

310-5029-F20

280-5009-01 280-5275-SR10 280-5008 601-0460

000-P00408-W 000-P00408 060-S00400 060-F00400

600-6455-02

600-7237-0150 600-7237-0250 ATR-60070 ATR-60071 ATR-60072 DESCRIPTION

COIN CHUTE TOWER SW UNIT METER UNIT CHUTE PLATE SINGLE CHUTE PLATE DOUBLE TNG LKG Locally supplied. STICKER 6.3V 0.15A Locally supplied. CASH BOX

ASSY C.C 2DR ~ ASSY C.C 2DR ~ Locally supplied. CAM LOCK MASTER W/O KEY Locally supplied. CAM LOCK W/KEYS Locally supplied. SUMITUBE F F 20MM Locally supplied. CORD CLAMP 21 CORD CLAMP SR10 CORD CLAMP 15 PLASTIC TIE BELT 100MM

MSCR PH W/FS M4 X 8 M SCR PH M4 X8 SPR WSHR M4 FLT WSHR M4

WIRE HARN C.C DOOR SINGLE Locally supplied. WH EARTH VD2-5&VD1.25-4 150MM. WH EARTH VD2-5&VD1.25-4 250MM WH SPEAKER TOWER WH COIN TOWER WH EXT CONT PNL TOWER (D-2/2)

NOTE

OTHERS USA OTHERS USA OTHERS USA

OTHERS HONG KONG, KOREA, TAIWAN USA OTHERS USA OTHERS USA OTHERS USA

OTHERS USA

Page 153

SW UNIT (INY-1180)

ITEM NO. PART NO.

INY-1181 421-8911

220-5179 509-5028 601-0042 310-5029-D20 601-0460

600-6609-32 600-6609-33 600-6609-34 DESCRIPTION

SW BRKT STICKER SW UNIT

VOL CONT B-SK OHM SW PB 1M KNOB 22 MM SUMITUBE F D 20 MM PLASTIC TIE BELT 100 MM

WIRE HARN TEST & SERVICE WIRE HARN VOLUME A WIRE HARN VOLUME B

Page 154

Qi) METER UNIT (ATR-3550)

ITEM NO.PART NO.DESCRIPTIONNOTE
1ATR-3551METER BRKT
2421-9168-01STICKER COIN METER
3HOT-1007LID COIN CNTROTHERS

NOT USED USA

101220-5643-01MAG CNTR DCSV 6P WH MZ-674-D04OTHERS

220-5617-02 MAG CNTR DCSV W/CONN 6P YE . USA 220-5643-02 MAG CNTR DCSV 6P YE MZ-674-D05_ -

102280-5275-SR10CORD CLAMP SR10
201000-P00308-WMSCR PH W/FS M3 X 8OTHERS

NOT USED USA

Page 155

(D-1/2)

  • LAMP UNIT (ATR-3600) as ova

(WI. J6)GE)W-NEP*E LON GW (wd. J6102)W-NS6*F LAN PW (WO. JBPT )W-NZE “TF vw (W9- $619) W- NBG *O

Page 156

@2) LAMP UNIT (ATR-3600)

ITEM NO. PART NO.

1 ATR-3601 2 ATR-3602 3 ATR-3603 4 ATR-3604 5 ATR-3605 6 ATR-3606 7 440-WS0002XEG

101 601-8288 102 390-6697-BL 103 838-14010-01 104 280-5275-SR10 105 280-5009-01 106 270-5052-04 107 601-0460

201 050-F00400 202 000-P00408-W 203 000-P00310-W

301 ATR-60082 (D-2/2)

DESCRIPTION

LAMP BASE DAMPER BRKT UPPER DAMPER BRKT LOWER LAMP HOLDER HOLDER BRKT INVERTER BRKT STICKER W POWER OFF ENG

RUBBER DUMPER CCFL TUBE W/PIPE L=330 BLUE CCFL INV S-12617C-7M W/L. CORD CLAMP SR10 CORD CLAMP 21 L.FILTER D PLASTIC TIE BELT 100MM

FLG NUT M4 MSCR PH W/FS M4 X 8 M SCR PH W/FS M3 X 10

WH LAMP

Page 157

@3) ASSY SW PANEL (ATR-3700)

ITEM NO. ° Q)

PART NO. DESCRIPTION

ATR-3701 SW PLATE

509-5712-04 SW PB W/L 6V ORANGE 509-5499-03-LN SW PB TRIANGLE YELLOW W/O LAMP 601-0460 PLASTIC TIE BELT 100MM

ATR-60080 WH CONT PNL

Page 158

ASSY MAIN BD (ATR-4000)

(D-1/2)

Page 159

ASSY MAIN BD (ATR-4000)

ITEM NO. PART NO.

1 ATR-4001 2 ATR-4050 3 105-5382 4 837-13551-92 5 APC-4002

101 400-5397-01 102 838-11856-UL 103 601-10369 104 610-0609 105 839-1073-03 106 400-542 1-03024 107 400-5421-05012 108 601-7467 109 280-0419 110 280-5009-01 111 601-0460 112 270-5117

201 000-P00308-W 202 000-P00408-W 203 000-P00416-W 204 011-P00325 205 011-T03516 206 011-T03512 207 011-F00316

301 ATR-60001 302 ATR-60002 303 ATR-60003 304 ATR-60004 305 ATR-60005 306 ATR-60006 307 ATR-60007 308 ATR-60010 309 ATR-60011 310 ATR-60012 311 ATR-60013 312 600-7141-100 313 600-7159-070 (D-2/2)

DESCRIPTION

WOODEN BASE ASSY SHILD CASE ATR SHIELD CASE BRKT I/O CONTROL BD FOR JVS SW REGU BRKT

SW REGU FOR JVS VA CONNECT BD UL STEREO PWR AMP 47 LOWPASS AMP 40HM 30W SSR BD 1 DC 2A SW REGU LCA30S-24 SW REGU LCAS0S-12 L-LOCK BK. HARNESS LUG CORD CLAMP 21 PLASTIC TIE BELT 100MM FERRITE CORE TDK ZCAT3035-1330

MSCR PH W/FS M3 X 8 M SCR PH W/FS M4 X 8 M SCR PH W/FS M4 X 16 TAP SCR PH 3 X 25 TAP SCR TH 3.5 X 16 TAP SCR TH 3.5 X 12 TAP SCR FH 3 X 16

WH CONN BD AC IN WH AC OUT 15P WH AC OUT 9P WH EXT DC MAIN BD WH VOL AND SOUND WH CENTER LINE WH SOUND LINE WH A/D WH I/O WH DC24V WH BRAKE OUT CABLE JVS TYPE A-B 100CM WIRE HARN JVS PWR 070CM

Page 160
  • ASSY SHIELD CASE ATR (ATR-4050)

ITEM NO.

COIAHARWNY S PART NO.

833-14150 839-1079-01 105-5378 105-5379 105-5381 421-9174 421-10023-AAB 421-10023-BCO. 441-314150 601-10642

260-0064 280-5275-SR10

010-P00310-F 000-P00408-W 000-P00325-W

FRQ-60037 DESCRIPTION

GAME BD ATR FLT BD SEGA HIKARU FRQ SHIELD CASE FOR SEGA HIKARU SHIELD CASE LID FOR SEGAHIKARU FLT BD BRKT FOR SEGA HIKARU STICKER CAUTION ANTISTATIC STICKER BD SERIAL NUMBER AAB STICKER BD SERIAL NUMBER BCO STICKER 833-14150 CARTON BOX SEGA HIKARU

FAN MOTOR DC12V CORD CLAMP SR10

S-TITE SCR PH W/F M3 X 10 MSCR PH W/FS M4 X 8 M SCR PH W/FS M3 X 25

WIRE HARN FAN SHIELD CASE,

Page 161

ASSY WIRE FRONT CABI (ATR-6001)

ASSY WIRE FRONT CABI (ATR-6001) is comprised of the following wire harnesses. An ASSY DRG. is unavailable.

ITEM NO. PART NO.

601-0460

ATR-60024 ATR-60025 ATR-60026 ATR-60027 ATR-60028 DESCRIPTION

PLASTIC TIE BELT 100MM

WH EXT COIN FRONT WH EXT INTERFACE FRONT WH EXT BRAKE FRONT WH EXT CONT PNL FRONT WH EXT LAMP FRONT

@7) ASSY WIRE REAR CABI (ATR-6002)

ASSY WIRE REAR CABI (ATR-6002) is comprised of the following wire harnesses. An ASSY DRG. is unavailable.

ITEM NO. PART NO.

601-0460

ATR-60040 ATR-60041 ATR-60042 ATR-60043 ATR-60044 DESCRIPTION

PLASTIC TIE BELT 100MM

WH EXT LAMP REAR WH EXT COIN REAR WH EXT CONT PNL REAR WH EXT SPEAKER REAR WH EXT INTERFACE REAR

Page 162

ASSY TRANS EXP (JEY-4200)

g 10A\ one 0 Je} UUUUY |Siere) cielo em:

Note: Make sure that there is no parts, wiring, etc. in the slash mark portions. When assembling, change PRIMARY side pin assignments if necessary depending on destinations.

ITEM NO. PART NO.

1 JEY-4201

101 560-5384 102 280-0419 103 514-5095-10000 104 514-5093 105 310-5029-F20 106 421-6595-08

201 000-P00516-W 202 068-552016 203 011-T03512 204 011-P00316

301 JEY-60080 302 JEY-60081 DESCRIPTION

WOODEN BASE TRANS EXP

XFMR 100-120V 100V 10A WB HARNESS LUG FUSE S.B 10000MA 250V HBC FUSE HLDR F-64AB COVER SUMITUBE F F 20MM STICKER 10A

M SCR PH W/FS MS X 16 FLT WSHR 5.5-20 X 1.6 TAP SCR TH 3.5 X 12 TAP SCR #1 PH 3 X 16

WIRE HARN XFMR IN WIRE HARN XFMR 100V OUT

Page 163

ASSY TRANS EXP 200V LINES (JEY-4210)

,

folifs| O

Note: Make sure that there is no parts, wiring, etc. in the slash mark portions. When assembling, change PRIMARY side pin assignments if necessary depending on destinations.

ITEM NO. PART NO.

JEY-4201

560-5377 280-0419 514-5095-10000 514-5093 310-5029-F20 421-6595-08

000-P00516-W 068-552016 011-T03512 011-P00316

JEY-60080 JEY-60081 DESCRIPTION

WOODEN BASE TRANS EXP

PWR XFMR 200-240V 100V 10A CE HARNESS LUG FUSE S.B 10000MA 250V HBC FUSE HLDR F-64AB COVER SUMITUBE F F 20MM STICKER 10A

M SCR PH W/FS MS X 16 FLT WSHR 5.5-20 X 1.6 TAP SCR TH 3.5 X 12 TAP SCR #1 PH 3 X 16

WIRE HARN XFMR IN WIRE HARN XFMR 100V OUT

Page 164
  • WIRE COLOR CODE TABLE

THE WIRE COLOR CODE is as follow:

mOaADPy PINK

SKY BLUE

BROWN

PURPLE

LIGHT GREEN

Wires other than those of any of the above 5 single colors will be displayed by 2 alphanumeric characters.

CaerIKNR WN RED

BLUE

YELLOW

GREEN

WHITE

ORANGE

BLACK

GRAY

If the right-hand side numeral of the code is 0, then the wire will be of a single color shown by the left-hand side numeral (see the above).

Note 1:
Note 2: If the right-hand side alphanumeric is not 0, that particular wire has a spiral color code. The left-hand side character shows the base color and the right-hand side one, the spiral color.

<Example> 51 oo... WHITE / RED

RED WHITE

The character following the wire color code indicates the size of the wire.

U: AWGI16

K: AWGI18

L: AWG20

None: AWG22

Page 165

VISIT OUR WEBSITE!

s9pI0H 2604 © SegaService.com

poeta G) http://www.seuservice.com/

‘Sega Ereerpeises Inc. USA Service Department phone 415.701.6580 fax 415.701.8594 Search criteria:

SERVICE

Dari's Office What's New Game Manuals Bultetins

[what! ! | (stafflDar's office) technical service][customer service][corporate info)[plugins][Non-framed page

A total of 661 people have accessed this page since June Sth.

Ifyou have any questions or comments about this Home Page please E-Mail to

darl davidson@seu sega. com OR dave cantrelle@seu sega com

> Sega Enterprise Inc., USA. All rights reserved

You will need the following items to view this page in its entirety.

Page 166

SEGA ENTERPRISES, INC. (USA)

45133 Industrial Drive Fremont, CA 94538 (415) 701-6580 phone (415) 701-6594 fax