CATHODE RAY TOMES

Skins Game Conversion Kit

Skins Game (1.06) (Midway, 2000) · Kit Manual · 45 pages · 26 sections · original scan

Page 1

FEBRUARY 2000 16-34042-101

Operations Manual Includes

Setup @ Service @ System @ Wiring @ Troubleshooting Midway Games West Inc. 675 Sycamore Dr. Milpitas, CA 95035 USA http://www.midway.com

Page 2

VIDEO GAME CONVERSION

KIT

Page 3

CONTENTS OF CONVERSION KIT

20-9620 KEY 7-20 TR-TX LONG ARM 4006-01005-08 MS 6-32x1/2 P—PH (2) 4006-01203-04 MS 6—32x1/4 P—PH W/SPRG SEMS (4) 4108-01219-10Y SMS #8x5/8 PIN HD-AB SPCL YEL (10) 4108-01193-10B SMS #8x5/8 TRX (10) 4408-01128-00 NUT 8-32 KEPS (14) 4700-00012-00 FW .172 x 3/75 x .047 (8) 5556—13956-00 FERRITE BEAD 2 PIECE 1-1/4 SQ. (2) H-21672 GROUNDWIRE H-23480 JOYSTICK ADAPTER HARNESS

20-10209-2 P/BUTTON LONG SHAFT WHITE (2) B~22589 OVaTIGK. AgSY, BASE, COLE | 20-10209-3 P/BUTTON LONG SHAFT BLUE (2) GI 2G4SS_ KEYEAD POD ASSEMBLY’ 20-10203-5 P/BUTTON LONG SHAFT YELLOW 04—12875 PLATE- JOYSTICK MOUNTING S8-3475 P/BUTTON ROUND ILLUMINATED 01-15029 BRACKET, HARD DRIVE > -

31-3456.3-2 BACKLIT MARQUEE. 31-3457“ DECAL, INSTRUCT BEZEL BOTTOM 4 31-3486 © DECAL, NSTRUCT BEZEL UPPER 31-3487 DECAL, SIDE_PANEL (2) 31-3488 DECAL, CONTL PNL WALLPAPER 41-3489 DECAL) CONTL PNL ADD ONS / 14-3490 DECAL, Joystic« 08-8067 CARDBOARD BEZEL, SLACK i 31-3602 DECAL, EXTREME MODE OVERLAY 03-9663 ATTRACTION ‘SHIELD __ A-23453 HARD DRIVE DISK ASSEMBLY 16-108'1 FLYER— SAFE HANDLING

A-23502 ELECTRONICS A 8587-825 LABEL~ FBI WARNING 9922.1 Lag EPILEPSY WARNING A an 10138 LABEL— WARNING FCC/CAN 03-9664 COVER, CONTROL PANEL TABEL- PATENT MI) oN REGISTRATION CARD MANUAC— UNIV. KIT TEMPLATE— CNTL PNL roy RM-28-01 1" BUBBLE PACK 24”

Ss

16-10812 LABEL, FRAGILE (3)

Poa 10055 LABEL

Page 4

CONVERSION KIT

CHAPTER

SAFETY & SETUP

NOTICE: This manual is subject to change without notice. Midway Games West Inc. reserves the right to make improvements in equipment function, design, or components as progress in engineering or manufacturing methods may warrant. Fill out and mail in the Game Information Card. Include the game serial number from the label on the rear of the cabinet. For your records, write the game serial number in the manual. SERIAL NUMBER

Page 5

SAFETY INSTRUCTIONS

The following safety instructions apply to operators and service personnel. Read these instructions before preparing the game for play. Other safety instructions appear throughout this manual.

DEFINITIONS OF SAFETY TERMS

DANGER indicates an imminent hazard. If you fail to avoid this hazard, it WILL cause death or serious injury.
WARNING indicates a potential hazard. If you fail to avoid this hazard, it COULD cause death or serious injury.
CAUTION indicates a potential hazard. If you fail to avoid this hazard, it MAY cause minor or moderate injury.
CAUTION also alerts you about unsafe practices.

NOTICE indicates information of special importance.

CAUTION: HANDLE DRIVES CAREFULLY The hard disk drive must be packed in an anti-static bag. When shipping the drive for repair or replacement, pack it in an approved container (P/N 08-8068). Do not stack or drop hard disk drives.
WARNING: DISCONNECT POWER Always turn AC power off and unplug the game before attempting service or adjustments unless otherwise instructed. Installing or repairing PC boards with power ON can damage components and void the warranty.
WARNING: GROUND GAMES. Avoid electrical shocks! Do not plug in a game until you have inspected and properly grounded it. Only plug this game into a grounded, three-wire outlet. Do not use a “cheater” plug, or cut off the ground pin on the line cord.
CAUTION: ATTACH CONNECTORS PROPERLY. Ensure proper mating. Do not force connectors that do not slip on easily. Reversed connectors may damage game and void warranty. Connector keys allow a connector to fit only one set of pins on a board. > Pebr
WARNING: HAZARD TO EPILEPTICS. A very small portion of the population has a condition that may cause them to experience epileptic seizures or have momentary loss of consciousness when viewing certain kinds of flashing lights or patterns present in our daily environment. These persons may experience seizures while watching some kinds of television pictures or playing certain video games. People who have not had any previous seizures may nonetheless have an undetected epileptic condition. If you or a family member experiences symptoms linked to an epileptic condition (e.g., seizures or loss of awareness), consult a physician at once before playing video games. We recommend that parents observe their children while they play video games. If you or your child experience the following symptoms: dizziness, altered vision, eye or muscle twitching, involuntary movements, loss of awareness, disorientation, or convulsions, DISCONTINUE USE IMMEDIATELY and consult a physician.

Setup - 2 Midway Games West Inc.

Page 6

Weicome to Skins Game!

It’s a beautiful day on the digital fairway. Midway Games West Inc. keeps the greens perpetually immaculate. In Skins Game, you and up to three other players are invited to practice your putting, perfect your drive, or simply haul off and lob a bucket of balls into the water hazards. Don’t worry. We'll refill the bucket.

Ultra-realistic Skins Game is just like a round of golf, minus the strenuous exercise. Your Midway caddy warns you about sand traps and water hazards and offers the best route for your shots. She selects what she thinks is the best club, but you may choose yourself from a full bag of putters, drivers, wedges, and irons—all custom crafted for optimal performance. As you enjoy your game, birds chirp peacefully in the distance and the sun shines with nary a cloud to speak of. Heatstroke is never a problem. Adjust your stance and shot direction all you like, but your virtual player begins each stroke oriented in the best stance and direction to hit the pin. While the three-dimensional terrain forces your ball to follow Newtonian physics, your shot “snaps” to the pin unless you choose to aim elsewhere. And a peek at the wind gauge may convince you to do so! The wind will send your ball off course if you're not careful. Of course in Extreme Mode, say bye-bye to Mr. Newton as you change the ball’s path or spin in mid-flight. Players who don’t dawdle at the tee earn QuickShot bonuses, rewards for hitting the ball within 15 seconds. Collecting 10 QuickShot bonuses gives you an extra Power Shot. And Power Shots mean added distance with your clubs. However, you must carefully time the joystick release, or your Power Shot becomes a nasty hook or slice. Normally, players earn one Power Shot for each three holes. As your game improves (or not), a hard drive records your scores. With the keypad, you can enter a PIN that identifies you and calls up your statistics—in case there was any doubt about your birdie on the fourth hole at Eagle Ridge.

PRODUCT SPECIFICATIONS

Equipment Requirements

Video Display MonitorAudio SystemWiring
Standard Resolution RGB2 Channel AudioJAMMA harness

Game Characteristics

Player VariablesOperator VariablesDiagnostics
1 to 4 players per gameCoinage, Play Mode,Automatic Power-Up Test
Choice of CharacterDifficulty, Volume,Manual Multi-Level Menu System

Character Profile Memory Audits, Statistics

NOTICE Skins Game conversion requires use of a low resolution monitor. You must also have a standard JAMMA wiring harness.

Skins Game Conversion Kit Setup - 3

Page 7

KIT COMPONENTS

Unpack materials from carton and inspect for obvious signs of damage. Use this checklist to ensure the kit is complete. Some of these parts may already be installed. You must supply the remainder of the materials required for this conversion. > > Item Part No. ie) Item Part No. & Artwork Controls

Side panel decal81-34872 Noystick assembly|A-233891
Marquee Artwork31-3456.3-21 Joystick mounting plate4-128751
Joystick decal81-34901 Joystick adapter harnessIH-234801
Button decals81-34891 _|Keypad pod assembly|A-234581
(Wallpaper decal81-34881 _|Keypad harnessIH-23445.21
Bezel instructions bottom decal [81-34571 [Blue pushbutton[20-10209-32
Bezel instructions top decal81-34861White pushbutton[20-10209-22
Extreme Mode Decal81-36021Yellow pushbutton[20-10209-51
Hardware and Toolsllluminated red start pushbutton81-34751

\Screw 6-32 x 1/4 p-ph w/ spring 4006-01209-04 4 Printed materials

Screw 6-32 x 1/2 p-ph44006-01005-082 Epilepsy warning116-9922.11
Inut 8-32 keps4408-01128-00 | 14 \Control panel template116-109961
Washers700-00012-00 | 8 |Registration card16-106501
Screw #8 x 16 pin yellow4108-01219-10Y | 10 \Cardboard bezel8-80671
\Screw #8 x 5/8 torx4108-01193-10B|10Electronics
(Torx wrench(20-96201 Electronics assembly|A-235021
Screw 8-32 x 1 44308-01123-20B | 4 [Ferrite bead1556-13956-00| 2
OverlaysHard drive assembly|A-234531
(Control panel cover03-96641_Hard drive bracket1-150291
Marquee clear shieldbs-96631 [Ground wireIH-216722

Recommended tools and supplies Utility knife, screwdrivers, liquid soap, nut drivers or socket wrench, wood filler material, black electrical tape, hole saw or equivalent, squeegee, soldering iron and solder, pliers or wire cutters, 180 grit sandpaper or electric sander, black semi-gloss paint, electric drill and wood drill bit set.

Setup - 4 Midway Games West Inc.

Page 8

CONVERTING A TYPICAL VIDEO GAME CABINET

PREPARE EXISTING CABINET

i Verify operation of existing game before changing cabinet. Pay special attention to parts you will reuse during conversion (e.g., power supply, monitor, coin mechs). Repair or replace damaged parts before installing kit. Switch off AC power. Disconnect AC line cord. Clear work area and cover or protect non-wood items (marquee, monitor, coin door, brackets, line cord, etc.).

ARTWORK Note location of decals or \ artwork and remove. Clean off glue residue. Fill gouges or unused holes with suitable filler material like quickhardening wood putty. Sand wood smooth and remove dust. 91-2456.

Evenly cover entire cabinet with black paint and allow to dry before continuing. Lightly moisten cabinet with soapy water. Remove decal backing and apply from top to bottom. When in place, smooth decal outwards, squeezing out air bubbles. Pop persistent air bubbles with a knife and smooth down. Allow 12 hours for adhesive to set. ar-a4a8

MARQUEE Remove existing marquee from cabinet. Check lamp and replace if cracked or if ends are darkened, even if it still works. Install kit marquee. Using previous shield as a guide, trim new attraction shield to size and deburr edges. Install new marquee attraction shield. ARTWORK LOCATIONS

Remove viewing glass and set in safe place. Clean CRT glass. Apply instructions decals to top and bottom of bezel. Place Epilepsy Warning label on front of monitor bezel. Ensure decals and labels do not obstruct viewing area. Clean bezel and viewing glass before installing in cabinet. CABINET Remove and save screws at top and sides of rear door. Unlock rear door. Lift door off cabinet and set aside. Use a vacuum cleaner to remove dirt or debris inside cabinet.

CONTROL PANEL Locate and unlock control panel latches or fasteners. Free panel from operating position. Label each harness wire before disconnecting from controls. Once wires are disconnected, remove control panel from cabinet and set aside. Save mounting brackets and hardware for later reinstallation.

. Some cabinets have speakers or other components on the control panel. Note polarity and function of wires before disconnecting. Incorrectly phased speakers cause weak low frequencies or a thin, hollow sound quality.

Skins Game Conversion Kit Setup - 5

Page 9

INSTALL PLAYER CONTROLS

TEMPLATE If control panel template is creased, flatten with a stack of books, newspapers, magazines, etc. Remove buttons, joysticks, or other controls from control panel. Remove covering and artwork, hinges or mounting brackets. Fill holes with suitable material (i.e., wood putty, glue, etc.). Let dry. Sand or file flat both sides of surface. Should you choose to replace the control panel board, it must match the original panel in size and thickness, and include all fastening and grounding hardware. Tape template on top of panel. Orient template to center controls. Cut and deburr holes. Remove template.

NOTICE: If existing game already has a recessed area where the joystick will go, you may not need to cut a new hole.

DECAL Remove backing and apply control panel decal to panel. Work down from top. After decal is in place, smooth it outwards, squeezing out air bubbles. Pop persistent air bubbles and smooth decal. Let adhesive set. Trim decal edges and cut joystick, button, and keypad holes to fit control panel. BUTTON DECALS Position control decals next to appropriate holes in the following order:

a. Camera b. Select Club c.Turn d. Extreme Mode rectangular overlay e. Start/Select f. Troon logo g. Midway logo OVERLAY Place plastic overlay on top of panel decals. Deburr overlay edges. Tape control panel template on top of overlay in same position as holes beneath overlay. Cut and deburr holes. Remove template. Fasten overlay with included hardware.

NOTICE: Some games require you to cut out a circle rather than a rectangle for the joystick. Observe notice on template for further instructions.

BUTTONS Disassemble each switch from its pushbutton. Bend large prong away from switch enough to slide switch off housing. Unscrew nut from housing. . Insert pushbutton housing through a button hole from top of control panel. Screw nut finger tight on switch housing from underside of panel. Snap switch back on housing. Repeat for each button.

Setup - 6 Midway Games West Inc.

Page 10

ILLUMINA ray USHBU

BUTTON —— (YELLOW)

JSTICK MOUNTING PLATE —\

PUSHBUT (BLUE)

U STUD DER J’STICK PLATE) PUSHBUTTON .

OVERLAY DEC.

STIC OVERLAY

TURN —/

PUSHBUTTON, JOYSTICK, AND KEYPAD LOCATIONS

  • Rotate pushbuttons so switch terminals are oriented toward JAMMA harness. Tighten nuts firmly.
  • JOYSTICK Align joystick mounting holes with control panel holes and insert carriage bolts. Install a flat washer and a nut on each carriage bolt and tighten securely.
  • Lay joystick mounting plate on top of joystick. Fasten with included hardware.
  • KEYPAD Insert keypad studs through holes in control panel. Install and tighten flat washers and nuts.
  • Remove backing from joystick mounting plate decal and place on plate. Smooth decal.
  • Close and lock control panel using existing fasteners.

Skins Game Conversion Kit Setup - 7

Page 11

INSTALL GAME ELECTRONICS

disconnect AC line cord before removing or replacing any component. After servicing ( WARNING: DISCONNECT POWER. To avoid electrical shock, turn off power switch and components, be sure all ground wires are secure before restoring power.

REMOVE OLD ELECTRONICS Label, then carefully disconnect cables on each printed electronics board assembly in cabinet. Note orientation of JAMMA edge connector on CPU Board Assembly. Remove boards and store in anti-static bags. Leave JAMMA harness in cabinet so you can reuse it. PREPARE ELECTRONICS Place Skins Game kit electronics assembly on flat, static-free work surface. Remove electronics cover and set aside. Inspect electronics for any damage and ensure all connectors are properly seated. LOCATE ELECTRONICS Place new groundplane (with electronics assembly, but without hard drive or groundplane cover) in cabinet in location of previous assembly. JAMMA edge connector header should face same direction as previous connector header. Mark mounting holes and set electronics aside. MOUNT ELECTRONICS Drill pilot holes where necessary and use hex-head screws to attach electronics to cabinet wall.

ELECTRONICS ASSEMBLY

Setup - 8 Midway Games West Inc.

Page 12

WIRE CABINET

CAUTION: ATTACH CONNECTORS PROPERLY. Be sure that printed circuit board (PCB) connectors mate properly. If connectors do not slip on easily, do not force them. A reversed connector may damage video game machine and void warranty. Connector keys only allow a connector to fit one set of pins on a board.
CAUTION: OBSERVE GROUNDING. Be aware of ground wires in game. Ground wires are usually green or green with a yellow stripe. Reuse any existing ground wires, and use ground wires included in this kit.

JAMMA HARNESS When wiring JAMMA harness to the controls and the CPU Board Assembly, refer to Cabinet Wiring Diagram in Wiring Chapter.

  • Attach component end of JAMMA harness to mate on CPU Board Assembly.
  • Attach free end of joystick adapter harness to its mate connector (P8) on the CPU Board Assembly.
  • Attach keypad harness to its mate connector (P26) on the CPU Board Assembly. Attach the other end of the harness to the pigtail on the keypad assembly Do not force connectors. They are keyed to fit only one way.
  • Attach Player 4 (P4) and coin door connectors to CPU Board Assembly.
  • Double check your connections to ensure they are all firm and secure. Do not force connectors.
  • JOYSTICK HARNESS Attach free connector of joystick harness to its mate connector on the joystick adapter harness H-23480. Connect one end of green/yellow wire to joystick mounting plate and other end to safety ground.
  • BUTTONS Mate each of the five small buttons and start button to corresponding JAMMA wires.
  • Connect one end of an H-21672 ground braid to control panel and other end to safety ground on power supply.
  • Ensure each button is connected to ground through JAMMA harness black ground.

= 5 NOTICE: Hard disk drives are sensitive to static. When not in use, store drives in anti-static ca bags. Do not drop or stack drives.

  • HARD DISK DRIVE Mount hard drive onto hard disk drive bracket. Note that end of bracket where holes are spaced closer together is where ribbon cable connects.
  • Mount bracket onto studs on electronics assembly with included KEPS nuts.
  • Connect data ribbon cable and power cable to Hard Disk Drive.
  • Replace groundplane cover. Secure to groundplane using all but one of the enclosed nuts.
  • Attach one end of second ground braid H-21672 to remaining groundplane post and fasten nut. Secure other end of braid to safety ground on power supply.
  • Replace and lock rear door.

Skins Game Conversion Kit Setup - 9

Page 13

POWER UP AND TEST GAME

Plug line cord into AC power source and turn on power switch. LEDs in electronics cage should illuminate. Using the 20-volt DC setting on a digital voltmeter, measure DC voltages at the power connector pins. Adjust the +5V source if it is necessary. Voltage tolerances are +.4 on +5V, +4 V on +12Vhe game begins self diagnostics. If no errors are found, Attract Mode begins. If problems occur, check wiring and refer to Troubleshooting Chapter. Unlock and open coin door. Press and hold TEST button to access Menu System. Use tests to verify operation of monitor, hard drive, speakers, and all pushbuttons and joystick and keypad. Exit the Select Test Menu to begin normal game operation. Open the coin door and press the SERVICE CREDITS button to allow game play. Choose a player position and press the START button to begin. Listen to the audio while playing the game. Note unexpected irregularities in sound (out of phase, no low frequencies, etc.). Check the wiring harness for internal shorts. Refer to Wiring for jumper locations and recommended settings, or Troubleshooting. Close and lock coin door. Allow the system to operate for several hours before attempting any game changes. Play several games to test operation of player panel buttons. Do they function? Do they operate consistently? Does each control perform its designated operation? Game play and earnings depend on proper performance of the VIEW, START and movement buttons. If any button does not operate properly, check connections against the wiring diagram. Replace intermittent or otherwise faulty controls.

CAUTION: SEEK FCC APPROVAL. Installation of this kit does not guarantee compliance with FCC requirements. You are solely responsible, and Midway has no responsibility for FCC. compliance of installed kits. Don’t install an FCC compliance label on the product until the FCC acknowledges compliance.

Setup - 10 Midway Games West Inc.

Page 14

SiS blll

CHAPTER

NOTICE: Instructions in this chapter apply to a typical converted Midway upright cabinet.

Page 15

SERVICE

CAUTION: Before attempting any of the following procedures on your Skins Game Video Game Machine, turn AC Power off. Failure to do so can cause personal injury, may damage the components, and may void your warrantee.

Control Panel

To remove controls, unlock and open control panel. Remove washers, nuts, and other fastening software before removing components. Disconnect and label wiring for easier reassembly. Remove plastic overlay if necessary.

Joystick Assembly Open control panel. Label and disconnect joystick wiring harness. Loosen and remove four nuts holding joystick to control panel. Lift joystick assembly out of control panel. To remove potentiometer, pull bottom of spring clip out to unlatch and pull clip up to remove. Pull potentiometer away from assembly gently to release.

Replace pot by seating snugly in its housing, flush against plastic base. If seated properly, pot cannot be rotated by hand more than a degree or two.

Service - 2 Midway Games West Inc.

Page 16

Push Buttons

Open control panel. Label and disconnect wires. Separate switch from its pushbutton. Bend large prong away from switch just enough to slide switch off housing. To remove light inside START button, pull light bulb up and out of socket. Unscrew switch mounting nut and pull entire pushbutton out from front of panel.

Fan Assembly Remove rear door. Remove hex

nutsongroundplanecover.

Remove cover and set in safe place. Disconnect wiring harness and remove mounting hex nuts and washers. Remove fan from cabinet.

Hard Disk Drive

Remove groundplane cover and set in safe place. Disconnect wires from hard drive and remove bracket mounting screws. Loosen screws in sides of drive and gently remove hard drive from bracket. Store and transport hard drive in anti-static bag. CPU Board Assembly Remove groundplane cover and set in safe place. Disconnect wires from harness. Remove mounting screws.

Battery Lithium battery sits on top of timekeeper IC. Carefully pry off battery and replace with identical type. Modem Card

Removegroundplanecover.

Remove modem cable from modem card. Remove modem mounting screw. Carefully remove modem

cardfromPCIslotwithout

excessive rocking motion.

Skins Game Conversion Kit Service - 3

Page 17

NOTES:

Service - 4 Midway Games West Inc.

Page 18

CHAPTER

NOTICE: This manual is subject to change without notice. Midway Games West Inc. reserves the right to make improvements in equipment function, design, or components as progress in engineering or manufacturing methods may warrant.

Page 19

GAME OPERATION

PLAYER CONTROLS Start/Select and “Power Shot” After currency is accepted this button starts a 1-, 2-, 3-, or

Change Camera4-player game. During play, this button can increase a club’sKeypad Pod
Choose between amaximum distance, provided the joystick is released atAssembly
behind-the-playerprecisely the right moment. Players earn one Power Shot perLets players enter their
view ora bird's-eyethree holes, but can earn more after 10 QuickShots.PINs as well as allow

view. operators to navigate the system menus. Select Club \ Cycles through a, your selection of clubs. During Extreme down. Mode, — buttons Tr bl add top- or back- left (© right \ spin.

Aim (Get Left/Get Right) Joystick Assembly Left button swivels player counter-clockwise Pulling back on the joystick winds your club backwards. around ball (from an overhead view), changing Pulling to the left aims the swing a bit to the right; lateral aim to the right. Right button changes pulling to the right aims the swing a bit to the left. lateral aim to the left. In Extreme Mode, buttons The joystick assembly is designed to withstand move an in-flight ball left or right. numerous sudden snaps back to neutral position.

OPERATOR CONTROLS

Increases volume. Decreases volume.

Ceases game play O or Attract Mode and opens Menu System Increments number of credits up one.

A TEST VOL. VOL. SERVICE

WY MODE UP DOWN CREDIT wv,

TYPICAL TEST SWITCH BRACKET PUSHBUTTON LOCATIONS,

System - 2 Midway Games West Inc.

Page 20

Menu System Follow instructions at the bottom of each menu screen to access more menus and change settings. The current date and time are shown.

ATLANTIS TESTS|

Day Date Year Time

ADJUST VOLUME

STATISTICS

GAME OPTIONS COIN OPTIONS TOURNAMENT OPTIONS

SET DATE/TIME

TESTS

EXIT TO GAME

To select test, use +/-/LEFT/RIGHT To run test, Press START or TEST

EPROM: X.XX Sept 7 1999 XX:XX:XX GUTS: X.XX Aug 30 1999 XX:XX:XX Game: Sep 2 1999 XX:XX:XX Serial #: XXXXXXX

ADJUST VOLUME

Raise or lower the volume during the game and during Attract Mode. Set the game volume first, then decide if Attract Mode will be as loud as the game (100%), or less. Attract Mode cannot be louder than game volume. You can also adjust volume with the control switches.

Game

To ADJUST volume, use +/-/LEFT/RIGHT To SELECT which volume, Press START or TEST To RESTORE old settings, press and hold START or TEST To SAVE settings and exit, Press VIEW or CREDIT

Skins Game Conversion Kit System - 3

Page 21

View game play and coin statistics.

Coin 1 (Left) Coin 2 (Right) Coin 3 Coin 4 Bill Value Service Credits Idle Mins 1 Player Mins 2 Player Mins 3 Player Mins 4 Player Mins New Games Cont Games Total Games 1-Player Games 2-Player Games 3-Player Games 4-Player Games Error Count Total Coins: Avg TIME/COIN Percentage Play : eR )

To clear these counters,

Hold START or TEST and press VIEW or CREDIT For more stats, press VIEW or CREDIT

System - 4 Midway Games West Inc.

Page 22

HISTOGRAMS

New Game Times (in seconds) Course Selected

Golfer Selected

Holes/game total Holes/game 1 player Holes/game 2 player Holes/game 3 player Holes/game 4 player Players per game Game Type QuickShot percent Power Shot percent Power Shot usage

Navigated shot percent CLEAR ALL HISTOGRAMS

To select Histogram, Use +/-/LEFT/RIGHT To show Histogram, Press START or TEST To return to menu, Press VIEW or CREDIT

Reset High Scores After Reboot (One Time Effect) No

Conservative Mode Off

To change settings, use +/-/LEFT/RIGHT To RESTORE old settings, Press START or TEST To SAVE settings and exit, Press VIEW or CREDIT

Skins Game Conversion Kit System - 5

Page 23

PRICING OPTIONS

Free Play: No (or Yes) Start game cost 1 Coin (1-12 Coins) Continue Game Cost

  • Coin (1-12 Coins) Bonus for quantity buy-in None

To change settings, use +/-/LEFT/RIGHT To RESTORE old settings, Press START or TEST To SAVE settings and exit, Press VIEW or CREDIT

MECH SETUP Activate mech to test. Current Status Mech 1 Mech 2 Mech 3 Mech 4 x4 Bill Service Each Mech 1 Pulse Worth: 1 Coin (up to 60 coins) Each Mech 2 Pulse Worth: 1 Coin (up to 60 coins) Each Mech 3 Pulse Worth: 1 Coin (up to 60 coins) Each Mech 4 Pulse Worth: 1 Coin (up to 60 coins) Each Bill Pulse Worth: 1 Coin (up to 60 coins) Stats and Counters Count: Coins (or pulses)

To change settings, use +/-/LEFT/RIGHT To RESTORE old settings, Press START or TEST To SAVE settings and exit, Press VIEW or CREDIT

System - 6 Midway Games West Inc.

Page 24

Dialup System Setup

Dialup Diagnostics

Dialup Statistics.

Date: Day Month Date, YEAR

Time: 10:14:41

Time Zone: (Not defined)

Time Zone Uses Daylight Savings Time: No

To RESTORE old setting, Press START or TEST To set digit, use +/-/LEFT/RIGHT or keypad To SAVE setting and exit, Press VIEW or CREDIT

CONTROLS TEST

COIN MECHS

1234

svc BILL

3A3

START 430

VIEW ctl CLUB + CLUB — AIM LEFT AIM RIGHT OB2 1E1 Ctl x

LAMP ON 2E9 MISC

TILT VOL +

TEST VOL—

Keypd

*O#

GRN=ok RED=Sw ON. YEL=Sw maybe. To activate LAMP, press START To reset pot limits, Press and hold START To activate coin counter, Press TILT Switch. To return to menu, Press and hold VIEW or CREDIT

Skins Game Conversion Kit System - 7

Page 25

MONITOR TESTS

COLOR BARS

Shows horizontal bars of red, green, blue, and white.

To cycle format, press START or TEST to return To return to menu, press VIEW or CREDIT

MONITOR TESTS

CONVERGENCE

Shows grid with dots in the center of each box. You can change the color of the boxes and dots.

To change color, press START or TEST to return To return to menu, press VIEW or CREDIT

MONITOR TESTS

PURITY

Fills the screen with red, green, blue, bright white, and white for brightness, 50% grey, grey, ones and black.

To change color, Press START or TEST To toggle text on/off, use +/-/LEFT/RIGHT To Return to menu, Press VIEW or CREDIT

System - 8 Midway Games West Inc.

Page 26

SOUND TESTS

HARDWARE TEST

** Testing Audio Hardware

Hardware Reset PASSED

V/O port test PASSED

DSP IDMA Test PASSED

Diag version 0.01

SDRC Revision 3

D/RAM 0 Test PASSED

D/RAM 1 Test PASSED

Bong Test: PASSED

Software Reset PASSED

DSP OS Version: 0.02

To return to menu, press VIEW or CREDIT

SOUND TESTS

SPEAKER TEST

A voice alternates speaking the word “left” into the left speaker and “right” into the right speaker to test your stereo capability.

To return to menu, Press VIEW or CREDIT

Skins Game Conversion Kit System - 9

Page 27

DISK TESTS

DRIVE READ TEST

Hard Drive Connected: Yes

Hard Drive Manufacturer_

Logical Sectors available: XXXXXXXX

LBA MB/SEC

—— ___ avg

min

max

Tests completed: 0

To return to menu, Press VIEW or CREDIT

DISK TESTS

FILESYSTEM CHECK

Total Files Used: XXXX

Passes Completed : x

Checking File: XXX.X

To Return to menu, Press VIEW or CREDIT

System - 10 Midway Games West Inc.

Page 28

MEMORY TESTS

VIDEO MEMORY TESTS

Bank 0:

Testing Bank 0... This test takes about 75 seconds. Please wait.

MEMORY TESTS

ROM TEST

Boot EPROM PASSED

Expansion EPROM (U17) test master is NOT installed

To return to menu, Press VIEW or CREDIT

UART TESTS

UART 0 (IOASIC) TEST

UART 1 (XMODEM )TEST UART 1 (XMODEM) RCV ONLY UART 2 (RS485) TEST UART 2 (RS485) RCV ONLY UART 3 PCI MODEM DIAL UART 3 PCI MODEM ANSWER

To select test, Use +/-/LEFT/RIGHT

To run test, Press START or TEST

To return to menu, Press VIEW or CREDIT

PRINTER PORT TEST

Printing Line:

Waiting for printer

To return to menu, Press VIEW or CREDIT

Skins Game Conversion Kit System - 11

Page 29

DIP SWITCHES TEST

U49

1 OFF - Run Game

2 OFF - Normal

3 OFF - Normal

4 OFF - Normal

5 OFF - Normal

6 OFF - Normal

7 OFF - Not Used

8 OFF - Not Used

U50

1 OFF - Not Used

2 OFF - Not Used

3 OFF - Not Used

4 OFF - Not Used

5 OFF - Not Used

6 OFF - Not Used

7 OFF - Not Used

8 OFF - Not Used

To return to menu, Press VIEW or CREDIT

System - 12 Midway Games West Inc.

Page 30

STANDARD PRICING TABLE

NAME.‘STARTCONTINUE | CREDITS/COINCOINT | COIN2[COINS | COINa | BILL
ANTILLES,221/25¢, 4G2561G
AUSTRALIA 122173X206, 2/$1.0020¢$1.00
AUSTRALIA 2221/5X20¢, 1/$1.0020¢$1.00
AUSTRIA 4221Sch, 210Sch5Sch_| 10Sch
AUSTRIA 2221/2X5Sch, 3/2X10Sch5Sch__|10Sch
BELGIUM 1221/20BF20BF20BF
BELGIUM 2223/20BF20BF20BF
BELGIUM3222/20BF20BF20BF
BELGIUM ECA221/20BF50BF20BFSBF
CANADA 1221/2256, 3/8125¢25¢
CANADA 2221/2x25¢,3/$125¢$1.00
CANADA 3223/$1.00, 6 / $2.00$1.00 | $2.00
CANADA ECA221/2x25¢,3/$125¢$1.00 | $2.00
DENMARK22B/SDKr, 70DKr‘SDKrTODKr
FINLAND.22TEmk.temk | 5¢mk
FRANCE 1222/5Fr, S/10FrFr10Fr
FRANCE 2212I5Fr, 4/10FrSFr10Fr
FRANCE 3211/5Fr, 3 0FrSFr10Fr
FRANCE 4211/5Fr, 21 0FrSFr10Fr
FRANCE 5212U5Fr, 5/10Fr, 11/2 X 10FrSFr10Fr
FRANCE 6212I5Fr, 4/10Fr, 9/2 X 10FrSFr10Fr
FRANCE 7211/5Fr, 3/1 0F r, 7/2 X 10FrSFr10Fr
FRANCE 8211/5Fr, 211 0F r, 5/2 X 10FrSFr10Fr
FRANCE 9211/3 X 1Fr, 2/5Fr1FrSFr
FRANCE 10211/2 X 1Fr, 3/5Fr1FrSFr
FRANCE 11211/3 X 1Fr, 2/5Fr, 5/2 X SFr1FrSFr
FRANCE 12211/2 X 1Fr, 3/5Fr, 7/2 X SFr1FrSFr
FRANCE ECA 111215Fr, S0FrFrSFr10Fr20Fr
FRANCE ECA 2112/5Fr, 4/10Fr1FrSFr10Fr20Fr
FRANCE ECA 3111/5Fr, 3M 0Fr1FrSFr10Fr20Fr
FRANCE ECA 4111/5Fr, 210Fr1FrSFr10Fr20Fr
FRANCE ECA 5112I5Fr, 5/10Fr, 11/2 X 10Fr1FrSFr10Fr20Fr
FRANCE ECA 6112I5Fr, 4/10Fr, 9/2 X 10Fr1FrSFr10Fr20Fr
FRANCE ECA7111/5Fr, 3/1 0F r, 7/2 X 10Fr1FrSFr10Fr20Fr
FRANCE ECA 8111/5Fr, 2/1 0F r, 5/2 X 10Fr1FrSFr10Fr20Fr
FRANCE ECA 9111/8 X 1Fr, 2/5Fr1FrSFr10Fr20Fr
FRANCE ECA10 | 111/2 X 1Fr, 3/5Fr1FrSFr10Fr20Fr
FRANCE ECA 1111118 X 1Fr, 2/5Fr, S/10Fr1FrSFr10Fr20Fr
FRANCE ECA12 | 111/2 X 1Fr, 3/5Fr, 7/1 0Fr1FrSFr10Fr20Fr
FRANCE ECA13 | 111M0Fr, 2/20Fr, 4/30Fr1FrSFr10Fr20Fr
FREE PLAY===NoneNoneNoneNoneNone
GERMANY 122T/1DM, 6/5DM1DMSDM
GERMANY 2211/1DM, 7/5DM1DM5DM
GERMANY 3211/1DM, 8/5DM1DM5DM
GERMANY 4211/1DM, 5/SDM1DM5DM
GERMANY 5211/1DM, 6/SDM1DM5DM
GERMANY ECA1 | 221/1DM, 2/2DM, 6/5DM.1DM20M5DM
GERMANY ECA2 | 241/1DM, 2/2DM, 6/5DM.1DM20M5DM
GERMANY ECA3_|111/1DM, 2/2DM, 6/5DM.10M20M5DM
HUNGARY,22T/2X10Ft, S/2X20Ft0Ft20Ft
TTALY221/500LItSOOLIt | SOOLIt
‘JAPAN 1221/100Yen'100100
JAPAN 2222H00Yen100100
JAPAN 3114/100Yen100100
JAPAN 4112H00Yen100100
JAPAN 5114/00Yen100100
JAPAN 6114/2X100Yen100100
NETHERLANDS22HPI, 3/2.5HFITHFI2.5HFI
NEW ZEALAND 1 | 7117$1$1$2
NEW ZEALAND 2 | 112181$1$2
NORWAY22SISNKr, 6/10NKr‘SNKrONKr
‘SPAIN 7227/100Pta, 6/500Pta700Pta_|S00Pta
SPAIN 2221/100Pta, 5/500Pta100Pta_|500Pta
SWEDEN22TBX18Kr, 2/5SKr1SKr5SKr
SWITZERLAND1| 221/1SFr, 6/SSFr1SFrSSFr
SWITZERLAND 2 | 22AMSFr, 7/5SFr1SFr5SFr
SWITZERLAND 3 | 221 SFr, 8/SSFr18FrSFr

(Table continues on next page)

Skins Game Conversion Kit System - 13

Page 31

STANDARD PRICING TABLE, continued

NAME.STARTCONTINUE | CREDITS/COINCOINT | COIN2 | COINS | COINS | BILL
UK ECA111150p, 3/£1.00£1.00__| 50p20p0p.£2.00
UK ECA2111150p, 2/81.00£1.00 | 50p20p0p.£2.00
UKECAS111730p, 2/50p, 5/£1.00£1.00__| 50p20p0p.£2.00
UK4111750p, 3/81.00£1.00 | 50p
UKS111750p, 2/81.00£1.00__| 50p
UK ECA 6111730p, 2/50p, 4/£1.00£1.00 | 50p20p0p.£2.00
UK ECAT113/£1.00£1.00 | 50p20p0p.£2.00
UK ECA8111/50p, 2/81.00, 4/£2.00£1.00 | 50p20p0p.£2.00
USAT221/25625¢25¢$1.00
usa2211/25¢25¢25¢$1.00
uUsA3111/25¢25¢25¢$1.00
usA4111/50¢, 3/$1.0025¢25¢$1.00
USAS211/50¢, 4/$1.0025¢25¢$1.00
USA111/50¢25¢25¢$1.00
USA7111/50¢, 3/$1.0025¢25¢$1.00
usas221/50¢, 4/$1.0025¢25¢$1.00
usa321/25¢, 4/$1.0025¢25¢$1.00
USA10331/25¢, 4/$1.0025¢25¢$1.00
usA1t421/25¢, 4/$1.0025¢25¢$1.00
USA12431/25¢, 4/$1.0025¢25¢$1.00
USA13441/25¢, 4/$1.0025¢25¢$1.00
USA ECA331/25¢, 4/$1.00$1.00 | 25¢10¢O5¢$1.00

System - 14 Midway Games West Inc.

Page 32

MIS CoA

CHAPTER

WIRING

NOTICE: This manual is subject to change without notice. Midway Games West Inc. reserves the right to make improvements in equipment function, design, or components as progress in engineering or manufacturing methods may warrant.

Page 33

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 34

CABINET WIRING DIAGRAM

ANIMA

CLUB DOWN AIM” LEF AIM. RIGHT CLUB UP CAMERA START

GROUND

+5v YoaXiS GROUND

PLAYER 4

Ne AS LAMP. K NG NC

KEYPAD

bos bao bos DoS Dae baz Dot KEY

HD PWR

rev GND GND +12V : |g egy

22+5v

5 > +8y

4|ono
5i> GND

6 t 7 t 5 p28 +iy

°||

a NOTE: MANY COMPUTER GRADE vet ol | PoweR'sueetes Use YELLOW | EL COIN | FOR =12V0C, AND WHITE OR |

LAMPS| BLUE FOR -SvOC. THIS 1S|

| ACCEPTABLE AS LONG AS THE | |. Pinour 'S CORREC

RN YeL BRN YeL oa 19] fishers

<8)alvo g
vio_oaNvio oRNoN
WHT BLU2]Slower Butain RiGHti
T_GRN2| | 4/oWRT RNeLOKUP,
aiT-YEL3) | §verveal
  • | 3[nwer START LAMP (C
  • | Lux U H contro §

i}

a)fssp ek 794gy
BLK2\loWHT BLK2\ Hone
WHT4BLK"

«er 6] Jo] Key

wiralle

3| [3 7] |?

I

CRN YE 4

KEYPAD

{ DISK } (ore)

AUXILLARY FAN

Skins Game Conversion Kit Wiring - 3

Page 35

Wiring - 4 see apsucaTION cHARt Bic

_J) POR PROPER INE CORD

POWER SWTCH axl S| Bux YE BLK YEL

1 RED

no WHT RED wt

BLK Buk

LINE

COMMONING

NEUTRAL

BLOCK

Midway Games West Inc. aux aux

NOTE: THERE ARE 4

FOR

  • RATING
  • FLUORESCENT LAMP ASSEMBLY OPERATION ON ITEMS THAT MUST 3E CHANGED FUSE APPLICATION CHART,

OTHER LINE VOLTAGES: OF POWER SUPPLY FUSE 120 LINE VOLTAGE FUSE RATING 3A SB _250V 24 SB 250V

  • VOLTAGE SWITCH ON POWER SUPPLY
  • AC. PO WER TRANSFORMER can vel

Buk BLK

BLK Buk eK Buk

aux ax Bu ak oan Yeu

Buk auk toa] |2 wt

ne e999

we Ne wat war aux Buk

GaN veL wi CRN veL

wer J = wer POWER CHASSIS GROUND LEADS

CONTROL PANEL COIN DOOR CASH DOOR war ax can vet Ir-uorescent oan VEL cH wt FOTURE

ne POWER WIRING DIAGRAM

Page 36

LED INFORMATION

On power-up, the seven segment LED display (LED2) counts from 0 to 6 twice, and then up to "f" (hexidecimal) as it initializes the board and loads the game software. When the first title screen appears, the LEDs darkens, and are not used during normal game play.

The red LEDs marked “CPU Power” and “Power” should be lit whenever AC power is on.

The red LEDs “RSTO,” “RST1,” and “RST2” behave as follows:

RST2RST1RSTOMeaning
ONONONNormal after AC power is on
ONONOFFSnapHat watchdog reset occurred
ONOFFONExpansion connector reset (This is not normal.)
ONOFFOFFOnboard reset button pressed
OFFONONSoftware issued a reset

JUMPER INFORMATION

Jumpers located around the CPU Board Assembly perform as follows: Jumper | 1-2 2-3 Meaning

JiX__|Normal 27C040 (512K x 8) boot EPROM
Jix27C080 (1024K x 8)
J2xXNot installed (development use only)
53X__|27C040 (512K x 8)

J3 xX Normal 27C080 (1024K x 8) expansion (update) EPROM

J4xNot installed (not used)
J5xNot installed (RS485 termination)
J6xNormal

DIP SWITCH INFORMATION

There are two banks of DIP switches on the CPU Board Assembly: U49 and U50. The following table describes the significance of the first two of the eight switches on the U50 DIP switch bank. The remaining six switches on U50 should be off. All eight switches on U49 should be off.

Switch 1 Switch 2 Meaning

OFFOFFNormal boot and run game or boot and run tournament update
OFFONBoot EPROM based self test
ONOFFBoot on-disk based self test
ONONBoot and run factory tests (labview) then run EPROM self test

Skins Game Conversion Kit Wiring - 5

Page 37

LOCATION OF LEDS, JUMPERS, DIP SWITCHES ON CPU BOARD ASSEMBLY

L nN NOeea

JIL

  • 000TH = ra = ee (ba

a aaTo% ron

ac fo)

CONNEC

(a es fat ‘eo

HEAT SINK

asnz i

Expansion EPROM S

ys BATTERY|| 5 Be

J5Es LED CONNECTOR

Wiring - 6 Midway Games West Inc.

Page 38

SMIWS Gli

CHAPTER

TROUBLESHOOTING

CAUTION: Turn AC power off before attempting any of the following procedures, unless otherwise specified. Failure to do so may damage equipment, cause personal injury, or void warranty.
Page 39

Machine Does Not Start Symptom Problem Suggested Solution

  • Machine appears non-functional.
  • Audio non-functional ¢ Fan non-functional
  • No video display Lack of electricity Check that power switch is on and line cord is plugged into grounded AC outlet.

Poor AC connection Test line cord, power plug and IEC receptacle for breaks or damage. Verify continuity of each wire. Fully seat IEC connector into cabinet receptacle. Verify wiring harness connectors are fully seated in the corresponding power supply receptacles. Verify AC wire connections at power supply terminals.

Broken fuse Replace broken fuse with identical type. Faulty AC line filter 1.

2. Check line filter with ohmmeter to verify operation. Replace line filter if bad.

  • Machine appears non-functional. ¢ Fan functional Wrong voltage Using voltage meter, correctly adjust +5V output on power supply using adjustment knob.
*Machine appearsPoor DC1.Fully seat DC cable connectors in power supply.

. Aaa Cohnection 2. Check power supply DC fuse. Replace broken fuse

orescent lg) with one with identical current and voltage rating. functional

Short circuit on3.Place CPU Board Assembly in known working

CPU board machine to verify operation.

assembly4.Replace faulty assembly with identical one.
*Machine appearsPoor connection1.Inspect CPU Board Assembly under low light
non-functional.across CPU Boardlevels. When board gets DC power, its LEDs glow,
*Currency acceptorAssemblyalthough voltages or signals may be incorrect.

Alumni aii 8 2. Turn AC power off. Ensure JAMMA connectors are

illuminated. fully seated onto mating CPU Board connector.

  • Power supply fan
functional3.Turn AC power on. Using 20-volt DC setting on a

digital voltmeter, measure DC voltages at the hard drive power connector pins. Adjust +5V source if necessary. Refer to Cabinet Wiring Diagram for wiring information and voltage limits

  • Using 2-volt AC setting on a digital voltmeter, measure same DC voltages as above. Any reading here indicates that supply voltages are unstable and may contain ripple or noise.
*Power-Up Self-Test | Faulty hard disk1.Turn AC power on. Press TEST MODE pushbutton
runs.driveto access Menu System. From DISK TESTS Menu,
*Attract Mode doeschooseDRIVEREADTEST.This _ indicates

not begin. | whether hard disk drive mechanism is functional.

eeiiiiialaialal2.Turn AC power off. Unlock and open rear door.

Troubleshooting - 2 Inspect board assemblies. Check that hard disk drive ribbon cable connector is fully seated in the mating connector on the CPU Board Assembly. Verify that all drive mounting screws are installed.

Midway Games West Inc.

Page 40

3. Check that hard disk drive is correct part. A label with assembly number and software version appears on each drive. Wrong component Verify that ROM instruction set and CPU Board set are correct. Components are marked with manufacturer name, assembly number and hardware version. Wrong voltage 1. Turn AC power on. Using 20-volt DC setting on a digital voltmeter, measure DC voltages present at power connector pins. Verify +5V source if it is adjustable. Refer to cabinet Wiring Diagram. Using the 2-volt AC setting on a digital voltmeter, measure the same DC voltages as above. Any reading indicates that the supply voltages are unstable and may contain ripple or noise.

Audio Problems Symptom Problem Suggested Solution

Video functional Game functional Audio non-functional Poor connection 1. Press TEST MODE pushbutton to enter Menu System. Choose ADJUST VOLUME. Ensure Attract Mode and game volume levels are not at zero. Adjust levels if necessary to produce sound. Inspect wiring harnesses and verify connections as indicated by the Cabinet Wiring Diagram. Using 20-volt DC setting on a digital voltmeter, measure DC voltages present at power connector pins. Verify +5V, -5V and +12V sources. Refer to Cabinet Wiring Diagram. Using 2-volt AC setting on a digital voltmeter, measure same DC voltages as above. Any reading here indicates that the supply voltages are unstable and may contain ripple or noise. Bad IC Place CPU Board in known good machine. Repair or replace if audio is non-functional. Audio distorted, muffled, missing frequencies Low hum present Faulty speakers 1.

2. Press TEST MODE to enter Menu System. From the Self-Test Menu, choose SOUND TESTS to verify some audio circuit functions. Turn AC power OFF. Remove grill and that each speaker is full range (100 Hz to 10 KHz response) and rated for at least 10 watts. Bad wiring Turn AC power off. Remove grille. Ensure no loose parts are caught in speaker cones, terminals, mounting screws, or stuck to magnets. Ensure wiring is not reversed on a speaker. Weak, low frequencies and thin or hollow sound quality suggests incorrectly phased speakers.

Verify wiring against Cabinet Wiring Diagram. Ensure there is a separate wire (not a common return) for each speaker. Ensure cabinet ground wires are connected.

Skins Game Troubleshooting - 3

Page 41
  • Using 2-volt AC setting on a digital voltmeter, measure voltages at the speaker terminals. Any reading here indicates that supply voltages are unstable and may contain ripple or noise.
  • Place speaker in working game to verify operation. ¢ Audio monaural Poor connection Verify wiring against Cabinet Wiring Diagram. Check for shorted wires.

Controls Problems Symptom Problem Suggested Solution + Joystick non- Joystick is out of From Self-Test Menu, choose CONTROLS TEST. functional or calibration Follow screen instructions to recalibrate joystick. functions erratically = Faulty wiring 1. Ensure wiring connectors are firmly seated in control panel and no wires are broken or pinched.

  • Repair or replace damaged cables. Reposition wires as necessary to avoid cinching. Poorly seated potentiometer
  • Inspect joystick assembly. A potentiometer may not be seated snugly. Remove a spring clip to reveal potentiometer. Try rotating potentiometer. If snug, it will not turn. If it turns, push it inward while turning until you correctly realign it and it seats tightly.
  • Replace clip and inspect other potentiometer. Bad potentiometer
  • Turn AC power on. Check voltage at each potentiometer. Put voltmeter leads on center tap and ground. Leave joystick in default position. Meter should read about +1.5V.
  • Use analog or bar graph digital voltmeter for this test: Put voltmeter leads on wiper and ground. Move joystick through its range. Check for smooth, linear transition between .5V and 1.5V. If meter jumps at any point, potentiometer is bad.
  • Replace a potentiometer that fails either test. Bad inline power fuse
  • Check voltages to CPU Board Assembly.
  • If +5VDC is absent, replace inline fuse on power cable. Use identical type fuse and retest voltages. Faulty Pot Amp chip
  • Test CPU Board Assembly in working machine.
  • If joystick is still bad, repair or replace. ¢ Joystick slips, seems loose. Poor response. Nylon spacer worn by rotating bracket
  • Remove joystick assembly, turn upside down, and check whether there is too much play in brackets when stick moves.

Invert nylon spacer 180 degrees and replace. If already inverted, replace with new spacer.

Troubleshooting - 4 Midway Games West Inc.

Page 42

Loose potentiometer captivating bracket Ensure pot captivating bracket is flush to flat of pot shaft and retaining screw is secure.

¢ — Joystick nonfunctional Faulty fuse Replace broken fuse with identical type.

¢ Button nonfunctional or functions erratically Poor connection Check connection and tighten.

Faulty button1.Place button in known working machine.
  • Replace faulty button with identical type.
+Startup button bulb | Faulty bulb4.Remove bulb and inspect filament.

non-functional ae .

  • Replace faulty bulb with identical type.
*Keypad non-Poor connection1.Check that connections are tight.

functional or .

functions erratically 2. Compare to Wiring Diagram to ensure accurate

connections.

Faulty keypad1.Place keypad in known good machine.
  • Replace faulty keypad with identical type.

Coin Mechanism Problems

SymptomProblemSuggested Solution
  • Currency or tokens are accepted
  • Number of credits per coin or bill is incorrect. Improper software settings Press TEST MODE pushbutton. Access CONTROLS TEST. Confirm operation of each coin or bill mechanism.

Access COIN OPTIONS. Verify that each mechanism’s pricing and setup options are set correctly. Faulty wiring Check that cabinet wiring is correct. Check that coin meter and coin switches connect properly to control input wires from JAMMA connector and CPU Board wiring. Ensure coin meter and coin switches connect properly to control input wires. ¢ Currency or tokens are accepted.

  • — Startup fails.
  • Audio and video functional Improper settings at Menu System Press TEST MODE pushbutton. Access COIN OPTIONS. Confirm pricing and setup of each mechanism.

Skins Game Troubleshooting - 5

Page 43

Bill Validator Problems Symptom Problem Suggested Solution

  • Bill validator does not function after field installation.
  • Coin mechanisms functional Improper software settings
  • Press TEST MODE to enter Menu System. Choose COIN OPTIONS. Confirm pricing and setup. If necessary, adjust pricing and setup. Check validator switch settings + = against manufacturer’s instruction sheet.

Miscellaneous

  • Game functional
  • Cabinet becomes warm after several hours of use. Obstructed fan Check air flow at bottom and rear of cabinet.

Clear obstructions.

Move cabinet away from sources of heat. FeN> Turn AC power off. Remove dust from vent holes with high-power vacuum cleaner. Faulty wiring Repair or replace fan wiring and connectors. Faulty fan Check operation of all fans. Replace if faulty.

  • Error messages appear on screen. Faulty hardware Check assembly cited in message. Call authorized distributor for help with unresolved screen messages.
  • Modem nonfunctional Bad connection Check that modem is well seated in PCI slot.

Cable disconnected Ensure cable is well seated in jack and modem.

Bad phone line

  • Plug cable into another wall jack.
  • Test jack with fax machine or telephone. Server down Reattempt connection tomorrow.

Bad modem card Replace faulty card with identical type

  • Clock is wrong Software set wrong Use Set DATE/TIME in Menu System to reset clock. Drained battery Replace lithium battery with identical type.

Troubleshooting - 6 Midway Games West Inc.

Page 44

NOTICE

The ‘libc” and “libm” libraries (the “Libraries”) are used with the “banner,” “bootbr,” “run_game,” “swts,” “host_hddnl,” “targ_hddnl” and “os.elf” applications (the “Applications”). The Libraries and their use are licensed without charge and are covered by the GNU Library General Public License. See the source and related files for the Libraries, which are found on the hard drive in /usr/src. Each Application, as linked with one or both of the Libraries (as the case may be), is referred to as a “Work.”

The owner of this coin-operated video game is permitted to modify the Works for his/her own use and to reverse engineer the Works in order to debug these modifications, provided that this permission applies only to the extent necessary to comply with the GNU Library General Public License. This permission does not include, and the owner does not have, any right whatsoever to distribute, transmit or otherwise disseminate the Applications or any copies thereof to any third party whatsoever. However, ANY SUCH MODIFICATION VOIDS ALL WARRANTIES, EXPRESS OR IMPLIED, RELATING TO THIS COIN-OPERATED VIDEO GAME AND ANY OTHER COIN-OPERATED VIDEO GAME INTO WHICH ANY MODIFICATION IS INSTALLED AND VOIDS ANY PARTICIPATION IN ANY TOURNAMENT THROUGH THIS COIN-OPERATED VIDEO GAME AND ANY OTHER COIN-OPERATED VIDEO GAME INTO WHICH ANY MODIFICATION IS INSTALLED.

Page 45

WARNINGS & NOTICES

WARNING Use of non-Midway Games West Inc. parts or circuit modifications may cause serious injury or equipment damage. Use only Midway authorized parts. + Use only authorized components and parts. Failure to do so will void warranty and may result in incorrect and/or unsafe operation.
  • This game is protected by federal copyright, trademark and patent laws. Unauthorized modifications may be illegal under federal law. This also applies to Midway Games West Inc. and Skins Game logos, designs, publications and assemblies. Moreover, facsimiles of Midway Games West Inc. equipment (or any feature thereof) may be illegal under federal law, regardless of whether or not such facsimiles are manufactured with Midway Games West Inc. components.
WARNING Prevent shock hazard and assure proper game operation. Plug this game only into a properly grounded outlet. Do not use a cheater plug to defeat the power cord's grounding pin. Do not cut off the ground pin.
WARNING A very small portion of the population has a condition which may cause them to experience epileptic seizures or have momentary loss of consciousness when viewing certain kinds of flashing lights or patterns that are present in our daily environment. These persons may experience seizures while watching some kinds of television pictures or playing certain video games. People who have not had any previous seizures may nonetheless have an undetected epileptic condition. If you or anyone in your family has experienced symptoms linked to an epileptic condition (e.g. seizures or loss of awareness), immediately consult your physician before using any video games. We recommend that parents observe their children while they play video games. If you or your child experience the following symptoms: dizziness, altered vision, eye or muscle twitching, involuntary movements, loss of awareness, disorientation, or convulsions, discontinue use immediately and consult your physician.

NOTICE No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may be transmitted, or otherwise copied for public or private use, without permission from the publisher.

For Service: Call your authorized Midway distributor.

MIDWAY GAMES WEST INC. 675 SYCAMORE DRIVE MILPITAS, CALIFORNIA 95035 UNITED STATES OF AMERICA

Entire contents of this manual copyright © 2000 Midway Games West Inc. Alll rights reserved.