CATHODE RAY TOMES

Sprint One TM-095 1st Printing

Sprint One (Atari Inc, 1978) · Technical Manual · 136 pages · 62 sections · original scan

Page 1
Scan of page 1

This page is a drawing, shown as the original scan.

Page 2

(GAME SERIAL NUMBER LOCATION

- Your game's serial number is stamped on the circuit (back) side,

__ bottom right corner, of the printed circuit board—see the illustra-

tion below. The same number is also stamped on the TV monitor chassis and on the label located on the rear of the game cabinet Please mention this number whenever calling your distributor for

chassis and on the label located on the rear of the game cabinet.

service. "3 ;

Page 3

Woodgrain and Graphics Versions

OMe SOULE.

Operation, Maintenance and Service Manual

Complete with Illustrated Parts Catalog

ATARI INC. 1265 BORREGAS AVENUE PO. BOX 9027 SUNNYVALE, CALIFORNIA 94086 408/745-2000 = TELEX 35-7488

rE KEE GAMES ‘a wholly owned subsidiary of Atari, Inc.

A Warner Communications Company tw]

Page 4

Copyright © 1978 by Atari, Inc, All rights reserved

Motorola and TEC service manuals reprinted by permission of Motorola Data Products and TEC Videoelectronics, Inc. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher.

For permission request, write:

ATARI INC 1265 Borregas Avenue P.O.Box 9027 Sunnyvale, Calitornia 94086

4G Lithographed in the U.S.A.

Page 5

TABLE OF CONTENTS

1 LOCATION SETUP

Cc

arms INTRODUCTION oo. c cece eect nenenneeen eennen a ee GAME INSPECTION INSTALLATION REQUIREMENTS: Power Requirements ........... Temperature Range . Humidity .......... Location Space Requirements Type of Power Cord .. INTERLOCK AND POWER ON/OFF SWITCHES OPERATOR OPTIONS ... SELF-TEST PROCEDURE . : VOLUME CONTROL ..... 0 sec c ee eee eect tence eee nn tne CYAWKHKWENNNNA

2 GAME PLAY A. B. Cc. ATTRACT MODE READY-TO-PLAY MODE . PLAY MODE ...........

3 smreicrresoi AND ADJUSTMENTS

rammoae

4 THEORY OF OPERATION A. B. . STEERING PCB REPLACEMENT ...... |. LED START SWITCH REPLACEMENT .... COIN MECHANISM , Components on Coin Door ... Access to Coin Mechanisms . Cleaning of Coin Paths Lubrication .....6.. 06sec eee Adjustment of Coin Switch Trip Wire .... Mechanical Adjustments on Coin Mechanism ... General Troubleshooting Hints ... CLEANING «0... 0 cece cere eens ADJUSTMENTS ON TV MONITOR TV MONITOR REMOVAL .. FLUORESCENT LAMPREMOYAL | FUSE REPLACEMENT

GENERAL INFORMATION COMPONENTS OF THE MICROCOMPUTER SYSTEM . Program Memory .... Read/Write Memory Microprocessing Unit Tri-State Devices . MICROCOMPUTER SYSTEM tee Program Memory Enable RAM Enable Phase 1 and Phase 2 ..

Page 6

TABLE OF CONTENTS

RAM Output 27 D,. MICROCOMPUTER WATCHDOG . 27 E. GAME CIRCUITRY COMPONENTS 27 System Clock and Sync Generator 27 Playfield Generator Motion Generator .. Video Output ...... + Car/Playfield Comparator . 40 Manual Control Interface 41 Motor Generator ....... . 42 Bang and Screech Generator . 42 Audio Output .... . 42

5 ILLUSTRATED PARTS CATALOG... B

6 TV MONITOR SERVICING INFORMATION.............. MOTOROLA Service Manual A. GENERAL {NFORMATION . B. SERVICE NOTES ........ Circuit Tracing ..... Component Removal . CRT Replacement .. Adjustments ....... Regulator Adjustment .. eee Horizontal Hold/Oscillator Adjustment Vertical Height/Linearity Adjustment ...... Focus Adjustment .. Monitor Servicing .. C. THEORY OF OPERATION . Power Supply . +73 Volt Supply ... Video Amplifiers and Output .. D. HORIZONTAL DEFLECTION CIRCUITS .. Phase Detector Horizontal Oscillator ... Horizontal Pulse Shaper and Driver Horizontal Output Syne Circuits ........ Vertical Oscillator and Output . Spot Kill ws Blanking Amplifier ...0.... 60000 cece cece eee eect t ete

Page 7

TEC Service Manual A. GENERAL B. SPECIFICATIONS Power Supply Input Power Consumption Video Input Picture Tube ... High Voltage Horizontal Retrace Time Resolution .. Scanning Frequency Tone Burst Amplifier . Environment ........+

LIST OF ILLUSTRATIONS

Figure 1-1 Location of Voltage-Changing Plugs ........++.0000sceeeeeeeeeeee 3 Figure 1-2 Location of On/Off, Interlock, Self-Test Switches, and Volume Control 4 Figure 1-3 Location of On/Off, Interlock, Self-Test Switches, and Volume Control (Graphics)....0. 000000 c cee eee 5 Figure 1-4 Caution Label on RF Board/Option DIP Switch on Game PCB . . 6 Figure 2-1 Attract Mode... cece cece c eee e nese tenet ee ee ees . 12 Figure 2-2. Ready-To-Play Mode . 12 Figure 2-3 Play Mode ......... 12 Figure 3-1 Coin Door Assembly ... 14 Figure 3-2. Hinging Open the Magnet Gate Assembly .14 Figure 3-3 Removal of Coin Mechanism .............- 5 Figure 3-4 Surfaces to Clean Inside the Coin Mechanism 215 Figure 3-5 Removal of Plate Covering Rear of Coin Slot . 15 Figure 3-6 Close-Up View of Lubrication Point ..... 15 Figure 3-7 Detail View of Coin Switch and Trip Wire . 16 Figure 3-8 Securing the Coin Switch Trip Wire 16 Figure 3-9 Adjustments on Coin Mechanism 17 Figure 3-10 Locations of Adjustments on TV Chassis Figure 3-11 TV Monitor Removal .o.... 2.0.0 ee eee eee . 20 Figure 3-12 TV Monitor and Fluorescent Lamp Removal (Graphics) . . Figure 3-13 LED START Switch Replacement .. 19 Figure 4-1 Sprint One PCB Block Diagram ... . 24 Figure 4-2 Phase 1 and Phase 2 Signa/ Shaping . 26 Figure 4-3. RAM Write Enable Signal Shaping .. .27 Figure 4-4 TV Monitor Playfield Display ....... 28 Figure 4-5 Playfield Generator Character Trace for the Letter “C’” . Figure 4.6 PCB Schematic Diagram (5 sheets) Figure 4-7 Steering Printed Circuit Assembly Output Pulses «-++-+++++--++++++

Page 8

LIST OF ILLUSTRATIONS

vi ILLUSTRATED PARTS CATALOG

Figure 5-1 Sprint One Final Assembly (Woodgrain) Figure 5-2. Cabinet Assembly (Woodgrain). . . Figure 5-3 Control Panel Assembly (Woodgrain) Figure 5-4 N Shift Assembly ...... sous Figure 5-5 Steering Wheel Assembly ...... Figure 5-6 — Steering Board Assembly . . Figure 5-7 TV Shelf Assembly . Figure 5-8 Power Supply Assembly Figure 5-9 Coin Door Assembly . Figure 5-10 Harness Schematic Figure 5-11 RF Shield PCB Assembly... Figure 5-12 Sprint One PCB Assembly. . Figure 5-13 Single Foot Pedal Assembly with Harness aia Figure 5-14 Sprint One Final Assembly (Graphics). . Figure 5-15 Cabinet Assembly (Graphics) Figure 5-16 Control Panel Assembly (Graphics) Figure 5-17 Display Assembly (Graphics Only) . eee eee Figure 5-18 Fluorescent Lamp Assembly ( Graphics Onl iy). beeen teen eee ee nee 90

TV MONITOR SERVICING INFORMATION

Figure 6-1 Motorola Monitor Circuit Board in Service Position ... Figure 6-2 Motorola Monitor Block Diagram Figure 6-3 +73 Volt Supply Circuit ......... Figure 6-4 — Motorola Monitor Vertical Drive Waveform Figure 6-5 Motorola Monitor Video Amplifiers and Output Circuit. Figure 6-6 — Motorola Monitor Horizontal Deflection Circuit ...... 100 Figure 6-7 Motorola Monitor Horizontal Deflection Waveforms Figure 6-8 | Motorola Monitor Horizontal Output Circuit Figure 6-9 — Motorola Monitor Sync Circuit Figure 6-10 Motorola Monitor Vertical Oscillator Circuit . Figure 6-11 Motorola Monitor Spot Killer Circuit ..... Figure 6-12 Motorola Monitor Blanking Amplifier Circuit .. Figure 6-13 Motorola Monitor Chassis Rear View—Component Location Figure 6-14 Motorola Monitor Circuit Board Detail—Solder View Figure 6-15 Motorola Monitor Schematic Diagram Figure 6-16 Motorola Monitor Circuit Board Detail—Component Location .... 107 Figure 6-17. TEC Monitor Chassis, Rear View .. Figure 6-18 TEC Monitor Chassis, Top View ... Figure 6-19 TEC Monitor Printed Circuit Board, Top View . Figure 6-20 TEC Monitor Schematic Diagram .. Figure 6-21 TEC Monitor Wiring Diagram

Page 9

Table 1-1 Table 1-2 Table 1-3

Table 4-1

Table 4.2 Table 4-3

Table 4-4

Table 4-5

Table 6-1 Table 6-2 Table 6-3

LIST OF TABLES

Operator Options (Switch Settings) . Self-Test Procedure ROM Locations for ROM Test Failure Indications ROM Program Memory Chips for various Sprint One PCB Configurations ... soe Conditions of Car/Playfield Data Output. . Operation of Multiplexer M8 with Given Input Address... 0.660. c ccc c eect eeec ee eee 40 MPU Addresses for Reading Switch Status MPU Data Line D6 D7 Input Approximate Base Voltage of Transistor Q1 or Q2 for Given Address ... 00... 06. c ccc cect cece Motorola Monitor Electrical Specifications Motorola Monitor Replacement Part Numbers. TEC Monitor Replacement Part Numbers

vii

Page 10

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 11

LOCATION SETUP

A. INTRODUCTION

Sprint One™ is a one-player driving game developed by Kee Games. The game is contained in an upright cabinet of either a woodgrain finish or one which is illustrated with brightly colored graphics to further enhance player appeal. A 23-inch TV monitor is mounted in the top front of the cabinet, with the monitor screen tilted back from the vertical. The TV monitor viewing screen is covered with a Plexiglas® panel.

Page 12

Player-operated controls are mounted directly below the TV monitor viewing screen on the front of the game cabinet. The controls consist of a steering wheel, a fourspeed gear shifter, an accelerator foot pedal, and an LED switch labeled START. A speaker mounted above the steering wheel in the upper shelf of the woodgrain cabinet version or above the TV monitor in the upper shelf of the graphics cabinet version provides the game sound.

Two identical coin mechanisms are mounted on the lower front center of the cabinet, below the steering and shifting controls. Either coin mechanism can initiate play. The cash box is located behind a locked access door to the coin mechanisms.

The player’s objective is to successfully keep his or her car within the boundaries of the race track and complete as many laps as possible before the end of game time. After the proper coins have been inserted into the coin mechanism, the player must press the START button. This begins the game play and the timer starts counting down from 100. Operating the white car, the player competes with the two black computer-controlled cars. As each cycle is completed, the track automatically changes, becoming progressively more difficult until the twelfth track is reached. A cycle consists of one or two laps, depending on which option has been selected. (See Table 1-1.)

Acceleration is simulated to that of a real car. The car will accelerate slowly if started in anything but first gear. Starting in first gear will enable the car to accelerate normally. Once the car is moving, shifting into progressively higher gears will increase the speed of the car. If the car goes into a turn too rapidly, the car will go into a driver-controllable skid, with the sound of the skid on the game speaker. Whenever the player’s car comes in contact with any of the other three cars or with an oil slick, the car goes into a semi-controllable skid. If the player’s car makes contact with the track boundary, a crash sound will be heard and the car will stop.

By passing through checkpoint areas on the track, a score is tallied at the top of the TV monitor screen. Ten points are awarded for the completion of each lap. The checkpoint areas, however, are not identified on the displayed track.

The outstanding feature of Sprint One therefore, is that it is a highly competitive game. Players must compete against themselves, as well as against the two computer-controlled cars. B. GAME INSPECTION Your new Sprint One game is manufactured by Kee Games with the intent of being ready to play immediately upon removal from the shipping carton. Your cooperation is needed to supply the final touch of quality control. Please follow the procedures below to ensure that your game is in perfect condition.

  • Examine all external parts of the game cabinet for dents, chips, or broken parts.
  • After determining that the game has been received in good condition, unlock and open the rear access door. Carefully inspect the interior and verify that:

¢ All plug-in connectors are firmly seated. The fuses are all seated in their holders.

  • No harness wires are disconnected.
  • No loose foreign objects are present, especially metal objects that could cause electrical problems.

Be sure all major assemblies are checked. Check the game printed circuit board (PCB), the transformer, the two coin mechanisms, the speaker, the player controls, and the TV monitor chassis.

C. INSTALLATION

REQUIREMENTS

Power Requirements and Line Voltage Selection Sprint One is shipped for operation at 110 VAC, 60 Hz, single-phase, rated at about 200 watts. However, if your local current is not 110 volts, follow this procedure. You must select one of four connectors at the power supply and plug it into the voltage selection socket. Figure 1-1 shows the four connectors, with one of them plugged in. The plugs are identified by wire color as listed in this figure. Note that there are two basic operating voltages—110VAC, 60 Hz and 220 VAC, 50 Hz, with provisions for low line voltage in each case. To insure proper operation, measure line voltage. If voltage is consistently below 190 V (for 110 VAC lines) or below 210 V (for 220 VAC lines), use the low-voltage connections.

Temperature Range Location and storage temperatures should not be below 0 degrees Celsius (32 degrees Fahrenheit),

Page 13

LINE VOLTAGE 95 VAC VOLTAGE-CHANGING PLUG WIRE COLOR BLACK ORANGE instalied at factor, 10 VAC

ON/OFF AND C4 INTERLOCK ba ‘SWITCH

3 Amp, 250 V. Slow - blow 8 Amp, 425V. Fast-Blow

Figure 1-1 Location of Voltage-Changing Plugs on the Power Supply

and no higher than 49 degrees Celsius (120 degrees Fahrenheit).

Humidity Range Relative humidity for location or storage shouid be no more than 95%.

Location Space Requirements The Sprint One game requires a minimum of 152 centimeters (60 inches) of vertical space; a minimum of 64 centimeters (25% inches) of width clearance; and 137 centimeters (54 inches} of depth clearance, including 76 centimeters (30 inches) of actual cabinet depth.

Type of Power Cord Kee Games has added a strain relief power cord to Sprint One. The advantage of this type of power cord is that, if pulled accidentally, the strain relief will hold the cord in place at the cabinet wall. The plastic strain relief “cushions” the impact of the shock and prevents the cord from pulling the wires out of the harness connector.

D. INTERLOCK AND POWER ON/OFF SWITCHES To minimize the hazard of electrical shock while you are working inside the game cabinet, an interlock switch has been installed at the rear access door, This switch removes all power from the game while the access door is open.

To heip you conserve energy, a power on/off switch has been installed on the Sprint One game so that it can be turned off during closed periods. The switch is located above the foot pedal in a recess, as shown in Figure 1-2.

Page 14

INTERLOCK SWITCH

<=)

VOLUME CONTROL

Ic

SELF-TEST SWITCH ON/OFF POWER SWITCH

Figure 1-2 Location of On/Off, Interlock, Self-Test Switches, and Volume Control (Woodgrain Cabinet)

Page 15

INTERLOCK SWITCH |

VOLUME CONTROL

SELF-TEST SWITCH ON/OFF POWER SWITCH

Figure 1-3 Location of On/Off, Interlock, Self-Test Switches and Velume Control (Graphics Cabinet)

Page 16

Please check for proper operation of the rear access door interlock switch by performing the following steps:

  • Unlock and open the rear access door.
  • Plug the AC power cord into a power source (wall plug).
  • Set the power on/off switch to the on position.
  • Close the rear access door. Within thirty seconds, the TV monitor should display a picture.
  • Slowly open the rear access door until the picture on the TV monitor disappears. The picture should disappear when the rear access door is opened less than one inch from the top.
  • If the results of Step 5 are satisfactory, the interlock switch is operating properly. If the picture does not disappear as described in Step 5, check to see if the switch is broken from its mounting or stuck in the on position.
  • Close and lock the rear access door. E. OPERATOR OPTIONS Options of the Sprint One game offer maximum player appeal for each game location. These options are listed in Table 1-1. They are preset for a certain game structure during production. To determine how the switches have been set for your game, compare the TV monitor viewing screen during the attract mode with the information in Table 1-1.

An additional method for determining these switch settings involves the self-test procedure. Set the self-test switch, located inside and to the left of the coin mechanism, to the on position. Compare the information on the TV monitor viewing screen during the self-test with the information in Table 1-1.

In order to change the toggle positions of the switch assembly and set the desired options, the printed circuit board (PCB) must be removed according to the following procedure:

1, Unplug the game. Unlock and open the rear access door.

  • Locate the radio frequency (RF) shield assembly immediately inside the cabinet on the right. (It is

rc | caution | | To avoid damaging capacitors | | on back of this PCB, move 1" | | toward arrows. Then pull to- | | Ward you. | | Assy. No, —| Game —_ o DAS Ss == to

ROW 2

Row 1

f 0° ROW 1 Gi I ROW 2 RF BOARD oboo PCB fe) ° 12345678910) —]

Figure 1-4 Caution Label on RF Board/Option DIP Switch on Game PCB

Page 17

Table 1-1 Operator Options

Switch Settings TV Monitor Display 1)2)3)4/5 )6/71!) 8 Results During Self-Test

ON Oil slicks added to tracks Oil OFF No oil slicks

ON Cycle to next track every lap OFF Cycle to next track every two laps Cycle

ON] ONGame cost—25¢ per player1 Coin Per Player
ON | OFFGame cost—25¢ for two players2 Players Per Coin
OFF| ONGame cost—50¢ per player2 Coins Per Player
OFF] OFFGame is free (No attract mode)Demo

ON Extended play equalling 3/10 of game time (set by toggles 7 and 8), if player obtains | Extended Play enough points to place halfway between Rookie and Pro rating during normal play. Exact point totals for extended play are displayed on the screen during game play. OFF No extended play.

ON Not used, any position OK OFF Not used, any position OK

ON| ON | Game time—150 seconds Time 150 ON| OFF |} Game time—120 seconds Time 120 OFF] ON | Game time— 90 seconds Time 90 OFF| OFF | Game time— 60 seconds Time 60

an aluminum box with small holes.) On one end of the box is a printed circuit board with an edge connector coming from the edge of the board.

  • Remove the five pan-head Phillips screws from each of the long sides (total of ten screws) of the RF shield assembly.
IMPORTANT To prevent damage to the capacitors on the rear side of the PCB, move the board about ¥% inch towards the edge connector (same direction as the two arrows on the small white label). Then pull the-RF board out toward yourself. Never yank the RF board straight out of the metal box. (See Figure 1-3 for caution label identification.)
  • Carefully remove the PCB from the RF shield assembly.
  • Set the switches for the desired options, as shown in Table 1-1.

6, Reinstall the PCB following Steps 7 through 4 in reverse order. Do not force or bend the printed circuit board. Before reinstalling, always inspect the printed circuit board for damage. Close and lock the rear access door.

  • Plug in the game and verify option functions by playing it.

F. SELF-TEST PROCEDURE The self-test procedure permits you to check the TV monitor, the character-generating and sync circuits, and the controls. It speeds up troubleshooting by quickly isolating many kinds of component problems. This feature tests about 95% of the game's circuitry. The tests, except for the switches, are done

Page 18

Table 1-2 Self-Test Procedure | Test Instruction Results if Test.Passes Results if Test Fails 1 Unlock and open | coin door. Set selftest slide switch (located inside and to the left of the coin door), to the “on” position.

(RAM Test) TV mor.itor “flashes” alphanumerics (A through Z, and 0 through 9) on the screen, while audio “hash” sound comes from speaker. Rotating car appears in the lower right-hand corner of the screen and moves diagonally toward upper lefthand corner. When the car reaches the upper left corner of the screen, RAM test is complete.

Tif RAM testing is satisfactory, sel | {test feature automatically begins | [the ROM test (Test 2). ! TV monitor display freezes.

NOTE TO TECHNICIAN

The TV monitor display freezes, with a letter or number showing on the screen. This letter or number corresponds to the alpha-numeric whose particular data code was not written into the RAM correctly.

2 No operator action required.

(ROM Test) Self-test operator sees a visual representation of game structuring in white characters at the top of the screen. No other visual effects appear on the screen, Black numbers appear in the center of the screen. Refer to Table 3 to to determine the failing ROM locations on the PCB. Match the part number of the game’s PCB with the part number in Table 1-3.

Set gear shifter in 4th position; then shift into 1st, 2nd, and 3rd positions.

Step on accelerator; foot pedal.

Press START button.

Trip tight and left coin acceptor wires. For each position except 4th gear, an audio screech sound occurs.

Audio screech sound occurs each time foot pedal is depressed.

Audio screech sound occurs each time START button is pressed.

Audio screech sound occurs each time wires are tripped. A constant screech sound indicates a stuck switch or a shorted harness. No screech sound indicates a broken switch or an open harness.

4 No operator action required. Light-emitting diode for START button activates automatically and stays on. Light in START button is not activated.

automatically when the self-test switch is turned on. The results of each test are displayed sequentially on the TV monitor until the self-test switch is turned off. High scores will reset to 000 when performing the self-test. We suggest that you run the self-test each time the coin box is emptied. See Table 1-2 for specific instructions on interpreting the self-test feature.

G. VOLUME CONTROL If volume is incorrect for your location, open the coin door and adjust the volume control. See Figure 1-2 for location of volume control.

Page 19

Table 1-3 ROM Locations for ROM Test Failure Indications ( Test 2 of Self-Test )

Failure Indication

Location of failing ROM for PCB 6433-01 B1 cl Lo} L1} MO} M1} NO] N1] PO | P1

Location of failing ROM for PCB 6433-02 BI ci D1 El

Page 20

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 21

During normal use Sprint One™ operates in one of three modes: attract, ready-to-play and play. Connecting the power cord to the proper AC source and activating the on/off switch energizes the game and begins the attract mode. When coins are inserted and clear the coin mechanism, the game goes into the ready-to-play mode. The play mode is then initiated by pressing the START button. The game timer will begin counting down from 100 by one-digit increments. When the game timer reaches zero, the game goes intoa “freeze mode” for approximately ten seconds before returning to the attract mode.

Page 22

A. ATTRACT MODE Figure 2-1 illustrates one of the TV monitor displays during the attract mode. The cars are displayed moving around the track. The tracks progressively change from the simplest to the most difficult. There is no sound during the attract mode. As the twelve tracks change, it is normal for some of the cars to “cheat’’ by going through some of the track boundary lines without crashing. On the TV monitor one or more of the following will be displayed:

1 COIN PER GAME 2 COINS PER GAME 2 GAMES PER COIN BLACK CARS DRIVE AUTOMATICALLY GAME OVER

B. READY-TO-PLAY MODE Figure 2-2 illustrates the TV monitor display during the ready-to-play mode before the START button is pressed. The insertion of the proper coins in the coin mechanism initiates this mode. When the coins clear the coin acceptor the display stops the automatic track changes, the easiest track is displayed, and the cars line up at the starting line.

In the ready-to-play mode the game reacts only to the START button. Pressing the START button places the game in the play mode.

C. PLAY MODE When the START button is pressed, a motor sound from the speaker begins. The TV monitor display is the same as the ready-to-play mode, except (1) the instruction PUSH START BUTTON disappears from the bottom of the display and (2) the game timer begins counting down from 100 (see Figure 2-3). Point requirements for extended play will also be displayed on the TV monitor screen during the play mode. (See Table 1-1 for specifics on extended play.)

When the play mode is initiated the player controls are activated. As the player advances his or her white car around the track, a score is tallied at the top of the TV monitor viewing screen. Two points are awarded for passing each of the five checkpoint areas on the track. The five checkpoint areas are not identified on the TV monitor display.

When the game timer reaches zero, a “freeze” mode is initiated for approximately ten seconds. The TV monitor display is the same as in the play mode, except (1) all car motion is “frozen,” (2) the words GAME OVER flash across the top of the TV monitor display, and (3) driver rating words GRANNY, ROOKIE, or PRO appear at the bottom of the display. After ten seconds the game will go back into the attract mode.

Figure 2-1 Attract Mode

TEME 200

WHITE,

Figure 2-2 Ready-To-Play Mode

Figure 2-3 Play Mode

Page 23

ADJUSTMENT

Due to its solid-state electronic circuitry, this Kee Games unit requires very little maintenance and only occasional adjustment. Information given in this chapter and elsewhere in the manual is intended to cover most servicing situations that may be encountered at the game site. The procedures given are in sufficient detail to be understood by a person with moderate technical background. If reading through this manual does not lead to solving a specific maintenance problem, you can reach Atari’s Customer Service Department by telephone Monday through Friday, from 7:30.a.m. to 4p.m. Pacific Time. From California, Alaska and Hawaii, call (408) 984- 1900; from the remaining 47 states call (800) 538-6892 toll-free.

If you are interested in gaining more information on video game technology, especially the electronics, we recommend reading the Video Game Operator's Handbook, manual number TM-043. This book is available from Atari, Inc., Attn. Customer Service Department, 2175 Martin Avenue, Santa Clara, CA 95050 for $5 each, or from your distributor.

Page 24

A. COIN MECHANISM Components On Coin Door Figure 3-1 shows the back side of the coin door assembly where the game’s two coin mechanisms are mounted. Included is the lock-out coil assembly; the lock-out wires are connected to this assembly but are hidden behind the coin mechanisms. During the attract mode the microcomputer energizes the lockout coil, causing the lock-out wires to retract far enough to allow genuine Coins to reach the coin box. But during the ready-to-play mode when the LED is lit, and during the play mode (and also when AC power to the game has been turned off), the lock-out coil is de-energized, causing the lock-out wires to move out far enough to divert coins over to the return chute.

Lamp Holder Coil

Figure 3-1 Coin Door Assembly

Directly below each coin mechanism is a secondary coin chute and a Coin switch with a trip wire extending out to the front edge of the chute. When the trip wire is positioned correctly, a coin passing down the secondary chute and into the coin box will momentarily push the trip wire down and cause the switch contacts to close.

Also shown in the photograph in Figure 3-1 is a slam switch assembly. It has been included to defeat Figure 3-2. Hinging Open the Magnet Gate Assembly:

any players who might try to obtain free game plays by violently pounding on the coin door to momentarily close the contacts on the coin switch. The slam switch contacts connect to the microcomputer system, which will ignore coin switch signals whenever the slam switch contacts are closed.

Access to Coin Mechanisms To remove jammed coins, and for maintenance cleaning, each magnet gate assembly can be hinged open without removing it from the door, as shown in Figure 3-2. Or, if necessary, each coin mechanism can be entirely removed from the door merely by pulling back ona release lever and simultaneously tilting the mechanism back, then lifting it up and out. This is shown in Figure 3-3. Cleaning of Coin Paths

CAUTION The use of an abrasive (such as steel woo! ora wire brush) or a lubrication on a coin mechanism will result in a rapid buildup of residue.

By talking to many operators, we have found that the best method of cleaning a coin mechanism is by using hot or boiling water and a mild detergent. A toothbrush may be used for those stubborn buildups

Page 25

of residue. After cleaning, flush thoroughly with hot or boiling water, then blow out all water with compressed air.

Figure 3-4 shows the surfaces to clean inside the coin mechanism. These include the inside surface of

(Clean both surfaces where coin enters the mechanism, as well as the magnet)

Figure 3-3 Removal of Coin Mechanism

the mainplate, and the corresponding surface of the gate assembly. There may also be metal particles clinging to the magnet itself. To remove these you can guide the point of a screwdriver or similar tool along the edge of the magnet.

If coins are not traveling as far as the coin mechanisms, you will need to clean the channel beneath the coin slot. To gain access to this channel, use a %-inch wrench and remove ali three nuts that secure the cover plate (refer to Figure 3-5. Removing the plate will provide access to the entire channel.

Also clean the inside surfaces of the secondary coin chutes, but when doing this be careful not to damage or bend the trip wires on the coin switches. Figure 3-5 Removal of Plate Covering Rear of Coin Slot Slot

Lubrication Do not apply lubrication to the coin mechanisms. The only points that may need lubrication (and only rarely) are the shafts of the scavenger buttons (coin rejection buttons) where they pass through the coin door. Apply only one drop of light machine oil, and be positive that no oil drops down onto a coin mechanism. Figure 3-6 shows this lubrication point. To ensure that no oil accidentally reaches the coin mechanism, remove the latter from the door before applying oil.

Manually hold down rejection button and apply one drop here

Lock-out Wire

Figure 3-4 Surfaces to Clean Inside the Coin Mechanism Figure 3-6 Close-Up View of Lubrication Point

Page 26

Correctly adjusted trip wire

Figure 3-7 Detail View of Coin Switch and Trip Wire

Figure 3-8 Securing the Coin Switch Trip Wire

Adjustment of Coin Switch Trip Wire In order for a coin switch to operate reliably when a coin travels down the secondary coin chute, the rest position of the switch’s trip wire should be as shown in Figure 3-7. Use extreme care when handling or touching these wires.

Three problems can occur with trip wires —they can be too long, too short, or become loosened and fall off. With a wire that is too long, you may have a problem of catching it on the opening in the cash box as a coin is accepted. You can cut off the end of the wire in small increments, making sure it still extends slightly through the “V’’ of the coin chute.

If the trip wire is too short (either by wrong adjustment or by being cut off too much), coins may slip by the wire without tripping it, and no credits will be given. The solution is to carefully bend and straighten out the wire to lengthen it. If you cannot straighten it sufficiently, contact your distributor to order another trip wire.

If (he wire is loose and falls off its mounting stud, it will also cause no credits to be given. Secure the wire by crimping together both ends of the brasscolored mounting stud with a pair of pliers (see Figure 3-8). If you should ever need to remove the trip wire, the two halves of the mounting stud can be separated with a small screwdriver.

Mechanical Adjustments on Coin Mechanism Coin mechanisms are adjusted prior to shipment from the factory and normally will retain these adjustments for many months. If, due to wear or other causes, it becomes necessary to make new adjustments, remove the coin mechanism from the coin door. Transfer it to a clean, well lighted area where it can be placed in a vertical position ona level surface (such as a bench top).

Along with a screwdriver you will need several coins, both old and new. Figure 3-9 shows an exploded view of the mechanism and gives procedures for adjusting the kicker, the separator, and the magnet gate. These adjustments should only be done by someone with experience in servicing coin mechanisms and who understands their operation.

General Troubleshooting Hints The first action item is to search for jammed coins. After these have been removed, examine the coin path for foreign material or loose objects (such as chewing gum, small metallic objects, paper wads, etc.). In cases where game usage is heavy, it may be necessary to clean the entire coin path periodically, in order to prevent buildup of contaminants that can hinder the movement of coins through the mechanisms. Also confirm that the trip wire on-each coin switch is intact, and is properly adjusted. If problems persist, check the condition and position of the lock-out wires, and the mechanical adjustment on the coin mechanisms, before suspecting the elec-

Page 27

ITEM IDENTIFICATIONS 1 Kicker and Separator Screws 2 Washers 3 Kicker 4 Separator 5 Gate Lever Spring 6 Gate Pivot Pin 7 Mainplate Assembly 8 “C" washer 9 Rail 10 Gate Assembly 12 Cradle Assembly

13 Gate Pivot Spring 14 Undersize Lever Assembly 15 Magnet Gate Assembly 16 Magnet Gate Adjuster 7 ‘ining Screws 18 Coverplate Assembly 19 Return Coverplate 20 Coverplate 21 Mounting Studs 22 Lower Gate Pivot Spring 23 Coin Release Lever Kicker and separator

  • Set the acceptor with the back of the unit facing you in the test position.
  • Loosen the kicker and separator screws (1) and move the kicker (3) and the separator (4) as far to the right as they will go. Lightly tighten the screws.
  • Insert several! test coins (both old and new) and note that some are returned by striking the separator.
  • Loosen the separator screw and move the separator a slight amount to the left. Lightly retighten the screw.
  • Insert the test coins again and, if some are still returned, repeat Step 4 until all the coins are accepted.
  • Loosen the kicker screw and move the kicker as far to the left as it will go. Lightly retighten the screw.
  • Insert the test coins and note that some are returned.
  • Loosen the kicker screw and move the kicker a slight amount to the right. Lightly retighten the screw.
  • Insert the test coins again and, if some are still returned, repeat Step 8 until all the coins are accepted.
  • Be sure that both screws are tight after the adjustments have been made.

Magnet gate

  • Set the acceptor with the front of the unit facing you in the test position.
  • Turn the magnet gate adjusting screw (16) out or counterclockwise until none of the coins will fit through.
  • With a coin resting in the acceptor entrance, turn the adjuster in or clockwise until the coin barely passes through the magnet gate. 4, Test this adjustment using several other coins (both old and new) ans, if any fail to pass through the magnet gate, repeat Step 3 until all the coins are accepted.
  • Fix the magnet gate adjusting screw in this position with a drop of glue.

Additional Cleaning

  • Remove the transfer cradle (12) and the undersize lever (14).
  • Use a pipe cleaner or similar effective cleaning tool to clean the bushings and pivot pins.
  • Replace the transfer cradle and the undersize lever.
  • To be certain the coin mechanism is completely free of any residue, place the mechanism in boiling water for several minutes. Carefully remove it and let it air-dry completely before reinstalling in the door.

Figure 3-9 Adjustments on Coin Mechanism

Page 28

tronics. lf a coin mechanism rejects genuine coins, try to readjust it. If this is not successful, replace it with a working mechanism.

B. CLEANING The exteriors of game cabinets and Plexiglas® panels may be cleaned with any non-abrasive household cleanser. If desired, special coin machine cleaners that leave no residue can be obtained from your distributor. Do not dry-wipe the plex panels because any dust can scratch the surface, thereby fogging the plastic.

C. ADJUSTMENTS ON TV MONITOR

CAUTION For best results be sure game has been turned on for a while before making any TV monitor adjustments.
NOTE The TV monitor adjustments are accessible through the rear door panel of the game cabinet. These adjustments have to be done while the game is energized. Therefore only persons familiar with safety measures and repair procedures on electrical equipment should perform them.

The TV monitor need be adjusted only when the picture is distorted or if the contrast or brightness seem out of adjustment.

The monitor's adjustments function like those of a conventional commercial television set, except that the volume adjustment has no effect. Instead, the game produces its sound in circuits separate from the TV monitor. Figure 3-10 shows the location of the adjustments on both TV monitors used by Atari. Your game contains a TV monitor manufactured to Kee Games’ specifications by either Motorola or TEC.

When making adjustments, follow these general guidelines: BRITE (Brightness) — Perform this adjustment before the contrast. Adjust so that the white lines covering the screen just barely disappear, when the brightness is turned up. CONT (Contrast) — Adjust so that the images are as distinct as possible against the grey background without being blurred. HORIZ HOLD (Horizontal Hold) or HORIZ OSC (Horizontal Oscillator) — Adjust if the picture is slightly off-center horizontally, if the images appear warped, or if the picture is broken up intoa series of diagonal lines. Adjust for a stable, centered picture. VERT HOLD (Vertical Hold) This needs adjustment only if the picture appears to be rolling up or down the screen. Adjust for a stable, centered picture.

D. TV MONITOR REMOVAL If the TV monitor proves to be at fault, remove the monitor as shown in Figure 3-11.

E. FLUORESCENT LAMP REMOVAL If the fluorescent lamp needs replacing, (Graphics version only) then remove the fluorescent lamp as illustrated in Figure 3-12.

F. FUSE REPLACEMENT Sprint One contains seven fuses, five on the power supply assembly in the lower cabinet and two on the TV monitor assembly in the upper (TV) cabinet. All fuses are easily accessible through the rear access door. Replace fuses only with the same type of fuse as follows:

TEC TM-600/TM-623 Monitors: 3AG 2-amp and 0.5-amp quick-blow, 250 volts

Motorola M5000/M7000 Monitors: 3AG 0.8-amp quick-blow, 250 volts Power Supply: Fuses F1 and F2 — 3AG 3-amp slow-blow, 250 volts Fuses F3 and F4 — 3AG 2.5-amp slow-blow, 125 volts Fuse F5 — 3AG 8-amp quick-blow, 125 volts

G. STEERING PCB REPLACEMENT

If it becomes necessary to replace the steering PCB, use the following procedure:

  • Unlock the coin door for easy access to the steering PCB.
  • Unplug the 10-pin Mojex connector from the steering PCB.
Page 29

Toontaast | \\ Cvgar Uvenr ow BRIGHT \ HEIGHT wontz voto) \_veRT Holo © VouTAGe SWITCH (leave im right position)

TEC MODEL TM- 600/623 2 FUSES~ REMOVE. COVER TO REPLACE (wotn 0.88 quick Bow)

MOTOROLA MODEL M5000/M7000

Figure 3-10 Locations of Adjustments on TV Chassis

  • With a 7/16-inch wrench, remove the self-locking hexagonal nut and %-inch internal tooth starlock washer fromthe steering wheel axle screw, while a helper holds the steering wheel at the front of the cabinet.
  • Remove the black plastic edge-toothed wheel.
  • Remove the steering PCB by removing two panhead #2-56 x ¥2-inch Phillips screws and lifting the board out.
  • Before installing the replacement steering PCB, be sure there is a sufficient amount of silicone \ubricant on the inner hole of the black plastic edgetoothed wheel.
  • Install the replacement PCB by completing Steps 1 through 5 in reverse order.

H. LED START SWITCH REPLACEMENT The start switch on the front panel has a very low failure rate. To test'a switch, unlock and open the. coin door. Remove the wires from the suspected switch. With a multimeter set on the Rx1 ohmmeter scale, test the contact opening and closing. If the contacts do not operate sharply, replace the switch. To change a switch follow the procedures listed in Figure 3-12.

  • Unlock and open the Coin Door.
  • Disconnect control panel cable connector, then remove two carriage bolts. Remove wires from suspected switch. Turn switch counterclockwise while holding cone-shaped nut on outside of game cabinet, Insiall new switch using reverse procedure, Reconnect harness wires.

Figure 3-13 LED Start Switch Replacement

Page 30

Pens

aan Remove control panel. Unplug connector. Remove playfield Plexiglas shield. Remove cardboard bezel. Unplug TV monitor chassis connector and remove four carriage bolts on TV shelf assembly Remove two eyebolt nuts. Remove TV monitor.

Figure 3-11 TV Monitor Removal

Page 31

TV MONITOR REMOVAL PEs

5. 6. Remove control panel. Unplug connector. Remove playfield Plexiglas shield Remove cardboard bezel. Unplug TV monitor chassis connector and remove four carriage bolts on TV shelf assembly. Remove two eyebolt nuts. Remove monitor.

FLUORESCENT LAMP REMOVAL 7.

  • Gently rotate fluorescent bulb until it slips out of socket. Remove fluorescent Remove attraction Plexiglas shield.

lamp.

Figure 3-12 TV Monitor and Fluorescent Lamp Removal (Graphics)

Page 32

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 33

A. GENERAL INFORMATION Electronically, the Sprint One game consists of a power supply, 2 TV monitor, a game printed circuit board (PCB), and a speaker. Mechanically, it consists of a control panel, foot pedal assembly, and a coin door.

This chapter provides a technical description of the Sprint One electronic circuitry. For easy reference, the Sprint One PCB is divided into 126 sections. These sections are identified by letters A through R (skipping letters G, I, O, and Q because they may be easily confused with numbers 6, 1, and 0 respectively) for the short side of the PCB, and numbers 1 through 9 for the long side of the PCB.

The following circuitry discussion is divided into two sections; the microcomputer circuitry and the game circuitry. Figure 41 is a block diagram of the entire Sprint One PCB.

THEORY OF OPERATION

Page 34

Figure 4-1 Sprint One PCB Block Diagram

PROGRAM

C(ADDRESS ADDRESS )S READIWRITE

MEMORY

RAM <ooc

PLAYFIELD

GENERATOR

PLAYFIELD OUTPUT

HORIZONTAL,

CAR LOCATION COUNTERS ENABLE VIDEO OUTPUT TO Tv

CAR VERTICAL LINE COMPARATOR CAR PLAYFIELD COMPARATOR

CAR PICTURE VIDEO.

CAR VIDEO OUTPUT

ADDRESS

ADDRESS: MANUAL, CONTROL ROM INTERFACE Q ATTRACT as | vee ee MOTOR

AUDIO AMPLIFIER TO SPEAKERS

SCREECH AND] |_ DATA ¥ BANG

DATA MONITOR

Page 35

She

Pe B. COMPONENTS OF THE MICROCOMPUTER SYSTEM The microcomputer system carries out complex tasks of the game by performing a large number of simple tasks. Control of the system is the primary function of the microprocessing unit. The microprocessing unit causes the system to perform the desired operations by addressing the program memory for an instruction. It then reads that instruction and executes the simple task dictated by the instruction. Temporary storage of data necessary for executing future instructions (such as arithmetic operations) is stored into a read/write memory.

Program Memory

Programmemory consistsofread-only

memories (ROMs), permanently programmed by Kee Games to execute the Sprint One game. This memory has the capability of producing 8 bits of data for each of 8,192 unique address locations. In computer terminology this is stated as a memory size of 8k x 8.

The Sprint One game contains one of three combinations of ROM chips to make up the program memory, depending on the dash number configuration of the game PCB. These combinations are listed in Table 4-1 and all combinations are illustrated on schematic sheet 3.

Since the data in the program memory is a permanent physical configuration of the ROM chips, the data is not lost when power is disconnected from the game or when the chip is removed from its socket. Since the program consists of read-only memory, the result of an address input can only be the “reading” of data stored in the manufacturing process. It is not possible to “write”’ in more data.

Read/Write Memory Read/write memory consists of random-access memory (RAM) which is composed of eight 1K x 1 2102-1s. Data may be stored in the RAM (called “writing” the RAM), then recalled later (called ‘‘reading”’ the RAM). The memory size of the read/write memory is referred to as 1K x 8.

In order to read from the RAM, R/W (pins 3) input ofall random-access memories must be high; to write into the RAM, R/W input must be low.

Data can be stored in the RAM by the MPU for the purpose of performing operations on it, as instructed by the program memory. Since the RAM is a temporary storage area, removing power from the RAM chips will “erase” all stored date.

Microprocessing Unit The controller of the microcomputer is the mi roprocessor (MPU). From the MPU, a sixteen-bit address bus addresses program memory, RAM and an address decoder. An eight-bit bi-directional data bus serves a path for transferring data from program memory as well as to and from the RAM and other interfacing devices.

Tri-State Devices Tri-state devices, such as E5 of schematic sheet 3, are capable of having normal logic output of ones and zeros when disable (pin 1) is low. When disable is high, the output becomes a high impedance. In other words, when disable is high, it is equivalent to completely removing device E5 from the circuit. ROMs and RAMs are also tri-state devices. Each ROM or RAM must be enabled by a certain logic level at its chip-enable input before the device is capable of outputting or inputting data.

C. MICROCOMPUTER SYSTEM The primary function of the Sprint One microcomputer is to instruct the game circuitry for the proper TV monitor display and audio outputs for corresponding manual inputs.

Table 4-1 ROM Program Memory Chips for Various Sprint One PCB Configurations

Sprint One PCB Location

aB1c1D1E1LouiMOM1NON1POP1

Part No.

6433-01x|xxxxxxxxx
6433-02x|xxx
Page 36

Program Memory Enable With initial power supplied to the Sprint One PCB, the MPU addresses program memory for an instruction by placing a 16-bit code at outputs ABO through AB15. The address decoder, consisting of ROM E2, one-of-ten decoders D2, F2, and £8, and addressable latch A1, receives the five most significant bits of this address code (address 9 through 13) as an instruction of which part of program memory to access. Outputs of one-of-ten decoder F2 enable only the individual ROMs of program memory required for the desired instruction.

RAM Enable With the address decoder now addressed for the enabling of the desired program ROM and the ROM addressed for a data instruction, the MPU receives the 8-bit data instruction on the data bus. If this data instruction includes the temporary storage of information, the MPU addresses the RAM and writes data into the memory RAMs. The procedure of writing into RAM is enabled by two signals; chip enable CE (pins

  • and R/W (read/write not, at pins 3) of the RAM must be low. The address decoder ROM (E2) receives an address (A9 through A13}, and one-of-ten decoder D2 receives a high write signal from the MPU. The result of these signals is a low DISPLAY at the input of multiplexer K2 for a low chip enable CE at pins 13 of the RAM. The MPU also causes the R/W (pins 3) input to the RAM to be pulsed, via the WRITE signal. When this inputis pulled low, MPU data on the data input to the RAM (pins 11) is stored into the RAM location determined by inputs AO through A9.

Phase 1 and Phase 2. Phase 1 (1) and phase 2 (2) are outputs of the MPU and are formed by shaping the pulse of horizontal synchronization pulse 4H by D-type flip-flop A7. The 4H input of A7 (pin 13) is fed twice through the flip-flop at a clock rate of 12.096 MHz. The output of the first flip-flop is fed through an OR gate to produce a phase 0 (®0) signal, as illustrated in Figure 4-2. The MPU provides an output of ®2 that is exactly like 0, except with a slight delay, and an output 1 that is of an opposite phase of 2. Phase 2 is fed through AND gate N3, which acts as a buffer.

When 1 is positive, the address and data lines of the MPU change and stabilize for the next output. When 92 is positive, the MPU addresses memory on the address bus and inputs or outputs data on the data bus. In order to guarantee that the MPU data is written to external devices at the proper time, write enable (WRITE A7, pin 10) is shaped by NAND gate A8& and D-type flip-flop A7 as illustrated in Figure 4-3.

Phase 2 is also used to control the output of RAM addres$ multiplexer K2, J2, and H2. The multiplexer

« TUUUUUUU UU UU

rs

© Dee | J8 pin 10

oo ins

60 [ | J

we [oT tins

ol | | C3 pin 3 A7 pin 13

C3 pin 37

Figure 4-2 Phase 1 and Phase 2 Signal Shaping *

Page 37

12.096 MHZ

4H

es Cs A8 pin 5

| A7 pin 10

330 120 NSEC + NSEC tise 9012 34 5 6 s

AB pin 2

Figure 4-3 RAM Write Enable Signal Shaping

acts as a 12-pole double-throw switch, and is switched at a rate of @2. The RAM is addressed by the MPU and data is transferred between the MPU and RAM when ®2 is high. When 2 is low, the RAM is addressed by horizontal and vertical synchronization, and data is read out of the RAM by the game control circuitry. ’ RAM Output As mentioned, the RAM serves as a data storage medium for the MPU. This stored data is used for two different purposes. It can be read back by the MPU if the program has need to access that information again. In-this case, the RAM output data is fed back onto the MPU data bus via tri-state buffers E5 and K5. This ‘RAM read” cycle is done when 2 is high and the MPU address lines are valid.

The other valid access of RAM data is for video and audio generation. In this case, the game circuitry reads the RAM output data when 2 is low, by addressing the RAM with horizontal and vertical line count information. The RAM output data is then latched by hex latch F5 and L5, at the end of each time period when ®2 was low, so that this data is held stable for use by the peripheral circuitry.

D. MICROCOMPUTER WATCHDOG Watchdog is an external monitoring system that resets the program memory back to its initial start-up instructions if the program execution deviates from its intended sequence. This is accomplished by a watchdog statement (address code) incorporated in the program memory, resulting in a TIMER RESET pulse at the output of the address decoder. This reset pulse must occur before decade counter C6 and 7 reaches the count of eight. Therefore if the program memory is functioning properly, a TIMER RESET pulse occurs within every eight frames of video.

E. GAME CIRCUITRY COMPONENTS The game circuitry receives game instructions from the microcomputer and responds with the proper video and audio outputs. The manual player controls of the game provide control information as data input to the microcomputer.

System Clock and Sync Generator The crystal-controlled clock generates a 12.096-MHz clock frequency that is used to produce all of the operating frequencies of the game.

The horizontal and vertical synchronization signals are used to produce a TV monitor raster made up of 262 horizontal lines at a horizontal frequency of 15,750 Hz (256H). Synchronized with line 224 is a vertical blanking pulse that occurs for the duration of 38 more horizontal scans, resulting in the total number of 262 lines per frame.

Playfield Generator The playfield generator generates both the playfield and al! alphanumeric video for the TV monitor display. This is accomplished by the playfield ROM (consisting of ROMs P4 and R4 fora memory size of 512 x 8), shift register R3, and binary counter R2.

Page 38

je oe oe lene ole

lo eee oes eee s

a

om is ‘a (oan aie ee le ole aaeeeae :

nob ob lene clin

Figure 4-4 TV Monitor Playfield Display

As illustrated in Figure 4-4 the TV monitor display is made up to 32 horizontal by 28 vertical grid sections (each eight lines tall by eight bits wide). For each grid . section, the microcomputer RAM stores a btye of data (one byte equals eight bits D0 through D7),

During the 2 cycle (®2 is high), the RAM is addressed by the MPU, at which time the desired byte of data is transferred from program memory to the RAM. Then, during the ®1 cycle (®2 is low), the horizontal and vertical synchronization signals can access each of these bytes of data as that particular grid is to be displayed. The RAM then outputs six bits of data (DISPLAY 0 through DISPLAY 5) that address any of the 64 different alphanumerics and playfield characters stored in the playfield ROM, and one bit (DIS- PLAY 7) that determines whether the character is to be displayed as black or white video.

The playfield ROM is programmed by Kee Games to provide eight bits of data for each of 512 addresses

  • characters of eight lines each). The least significant addresses are from vertical synchronization 1V, 2V, and 4V, and the most significant addresses are DISPLAY 0 through DISPLAY 5 from the microcomputer RAM.
Page 39

OH 1H 2H 3H 4H 5H 6H 7H

w—J COL

Figure 4-5 Playfield Generator Character Trace for the Letier “C’”

The top of Figure 4-5 illustrates the letter “C’’ as it would be “traced” on the TV monitor display. The RAM would provide one six-bit address to the playfield ROM for the letter, while vertical synchronization 1V, 2V, and 4V would complement the RAM address for each of the horizontal scan lines. The bottom of Figure 4-5 ilustrates the output of shift register R3 for each horizontal scan.

Note the letter “"C” in the word SCORE in Figure 4-4, In order to generate the character in this location, the microcomputer RAM outputs a data code when this part of the display is being scanned. This six-bit code (DISPLAY 0 through DISPLAY 5) contains the playfield ROM address for the letter C.” Vertical synchronization 1V, 2V, and 4V determines which one of the eight lines of the character is being scanned at that time.

Shift register R3 then loads the actual playfield or alphanumeric data from the playfield ROM and shifts it out in serial video (R3 pin 13).

Binary counter R2 latches data DISPLAY 7 from the microcomputer RAM. This results in the selection of white playfield video if DISPLAY 7 is high, or black playfield video if DISPLAY 7 is low. Some alphanumerics and all oil slicks are represented in black video, while all of the racetrack boundary (playfield) is represented in white video.

Binary counter R2 is also used to produce the COMP SYNC, COMP BLANK, and a 256H signal that are al! delayed one character's width from their original timing. This delay is used to center the playfield on the monitor's horizontal scan.

Motion Generator The motion generator generates the video for the three cars, which are the only moving objects of the Sprint One game. The picture ROM (consisting of ROMs $6 and K6, for a memory size of 512 x 8) is programmed by Kee Games to provide 16 bits of data for each of the 8 lines of each of the 32 different states of rotation of a car.

The microcomputer RAM provides three words (bytes) of data for the display of each car picture. The first byte determines the vertical location of the car, the second determines the proper rotation picture of the car, and the third determines the horizontal location of the car. The accessing of these bytes of RAM data is done during the horizontal blanking period (256).

Vertical position data is received by vertical line comparator M4 and L4. Take, for example, the data code for a car to be displayed beginning on fine 120. The RAM byte data code of 01111000 would be loaded into the comparator. When the vertical line comparator reaches the count of 01111000, and 8H, 64H, 356H, and ®2 are all high, the conditions are met for alow signal at the output of NAND gate N4 (pin 8). One 2 clock pulse later, alow appears at the Q3 (pin

  • output of latch L5 (clock input for L5 is located on
Page 40

Pees FT Ts |e ds 7[,bB Pi Pe PS PE cer

PrEpLAY 5: DISPLAY + Fs y

z DISPLAY 3 Dis Heme DISPLAY DISPLAY # av &

av w BEPEIRRLE 1B cous9e CHAR LSB

yanor ses Re Jor fer as fo foe fe

y aw ay ew wy av wav.

CARS LAEK PLAYFIELD __ WHITE PAYED TART

tee COMP BLANK # —

ln] 5) 2 [oly + 2 peerage | ts, VfB) : sg, aa} ~ escnm™ Po 9316 aol — comp SYNC rs It aif — come sane

Page 41

NOTES: UNLESS OTHERWISE SPECIFIEO L RESISTANCE VALUES ARE IN OAMS 2 CAPACITANCE VALUES AREIN MICRO FARARDS NOTICE TO ALL PERSONS SECEWING THIS DRAWING CONFIDENTIAL: Reproduction forbidden winout the Specific written permission. of Atari, tne... Surayvale, California: This drawing #8 only conditionally Issued. and baither fecelpt no! possessior.theren! confers or tranafers any right. in, oF license te ier of the drawing or any design or tec ‘thereon, nor any rght (oreproduve ing or any ari Wareot axcept Yor manvlacture by vendors of Nar, cor porated and for manufacture under tne corporaticn's writ jen Tense, 00 ght to reproduce Us drawing Is granted ‘ie subjéct mavier thereof unless by willen agreement ‘with oF written permission from. the corporation.

BEF DES tGAATION

toc“TyreMighesT[Wor USED
Bes[PMG rhees082 ae354 A 5 C345.0738,69 9O,BE

orn SPY 2A2830.80, tp AT SEB 38, 7 fay ies as, ons

REFERENCE ONLY

zalVGLANRMawalgelalslalalelst 1]THI| TTTeTelB ie.
aeVRCANK®No8/313) S18 /e/8F9) !je838
saltvreserTemean 85[2|8)3/388iBered

1 |

arfaEatna
Af"RSET;
cu —-—/an7:

° R47 1 “HOWE Ua] R), 2,4,33, 38, H No.5 VAL ve ‘

  • 45 { EATER aa 1096

¥

2suc

CIN:1 EssthiG . PLAYEIELDAPo

peer RAYFIELD Taxa ETS S00 we

= i

ke

Figure 4-6 Sprint One Schematic Diagram Sheet 1 of 5 006433 c

Page 42

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 43

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Aaproduction forbidden without tre Specitic writer. permission of Aten, Inc, Sunnyvate, Galiforsia” This clawing Is only condiionally issued, and neither recerpl nor possession ineroot confers of transiers ny right In, or license 10 use, the subject matter of tne Grtwing oF any design oF Techical information shown ‘nateon, ner any rigntto reproduce inis drawing o! any part thereof. except tor manutacture by vendors of Alan, incor: poreted and fer manutaclure undor ine corpocalien's wit {en jicenso, n0 fight to reproduce IMs Orawing is granted for the subjset matter thereor unless by wrtten agreement Wit oF waltten permission trom the corporation.

DISPLAY DISPUT 1 cs RSPLAY a

la (efits Ja do be egg a uses of —— serv vio? vine wins vio 4 vid Ss vig 2 W301 NID B

DISPLAY be

ke 8 % Ps hs lev ausies co) fen | Sa ssacac Tete Te TT, | U Eras | | etl Bra

Pae

: yh mspiny @ DISPLAY 3 DISPLAY 2 of ispiny

a a im i 2 ole pt % z g & a T 74 S105

Figure 4-6 Sprint One Schematic Diagram Sheet 2 of 5 006433 Cc

Page 44

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 45

x Ka Br aieee i ceectt af, She a oa. 652 Hae Stic af Ape DISPLAY

si ATE DIOPLAYE De PLAve BISPLAYS

DISPLAYS NOTICE 70 ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, California. This drawing is only conditionally issued, and neither recelpt nor possession Hereo! confers or ansiers any right in, oF license to use, tne subject matter of the Grawing of ‘any design or technical information shown thereon, nor any ightto reproduce this drawing or any part tereo!, except for manutseture by Vendors of Ata, Incor porated and for manufacture under tne corporation's wrt 10 right to reprodyce this drawing is granted ‘matter thereo! untess by witten agreement ‘with or written permasion from the corporation,

OB

BSPLACS GisPuay? bt

bs

v2

D3

er

ADRI-ADRD, ADRB ADRS. De

Dp-p3 ADRG- ARs,

D4-07

Figure 4-6 Sprint One Schematic Diagram Sheet 3 of 5

006433 Cc

Page 46

CODSOS aud au 8 vt

-aeues35ais
  • asia 241 aia Agia [23 Als
ABi2 =oAlz
ABI zo+.Al

AB LA AIO Age HE sw3

os

20-6003

ace [Lt

40 ABT RESET Rk SYNC

ABS

a \ D WRITE orf ol bs 4 ®

au 13 | sal 2

£, 2750

Vss_Vss 08908! DBZ 083 024 DBS Doe 087] lo la] te) o

Be 1 fer ]33 |sz (31 [30 [29 [za [27 | 2a COOCOO = 2 ne34 07 DaIEF <y a

De7 deDBUse
os.Sopauss
oai SoopBuS4

ante pauSss Baus3 Ds Be

D2aeDeus

a

D1p62peas

Ba et

op£DBUS y

ATTRACT

VRESET

VBLANK®

Page 47

NOTICE TO ALL PERSONS RECEIVING THIS ORAWING CONFIDENTIAL: Reproduction” forbidden without the ‘specific welten permission of Atari, Inc... Sunnyvale, Gabfornias This crawing is only conditionally issued, and neither receipt nor possession thereof confers or translers ‘any right in, oF license To use, the subject matter of the drawing or ‘any design or technical information shown thereon, nor any “ight to reproduce this drawing or there! except for manutacture by vendors of Ata porated and for manufacture under the corporalior {envlicense, no right to reproduce this drawing Is granted forthe subject matter thereof unless By wl ‘witn oF weltten permission trom tne corpor ‘ 2 3

Beapl

sal

asHeagle‘a22
aiz—3asealHetara pil
antala Be 38'Sl,g32ROM
aB=2#p2——PROMS
AeHp9gio,ofaPROME
pag Be"ebpRom7
a3}?7SPROMS

ai ape 7 apt

Wea

Rw | Le im pot EOLLISION, po ey bt S14 9301-7 — : OTSPLAY

op

ob?

BoAB12TIMER RESE

WRITE 2plll —__carlision RESET |

ADRSaz3p

4p21 __. STEERING RESETT

ADRS.lay5b 3
eeopt 4NOISE RESET
aR?Sag7b

9301 8 p= a}2

14 la E yp 80 ATTRACT ‘i OR € w0 Ols aw MICROPROCESS:

Ape12ma7235ZH.et

anne fan es ales came Lk acns ——2]a ho ~

ADReABae

arte

P

Figure 4-6 Sprint One Schematic Diagram Sheet 4 of 5 006433 c

Page 48

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 49

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 50

schematic sheet 3). This signal is used to generate the LDV x A and LDV x B load pulses.

The RAM byte data code that controls car rotation is capable of addressing any of 32 different car pictures. The five bits of data code necessary to do this (DISPLAY 3 through DISPLAY 7} are applied directly to the address input of the car picture ROM J6 and K6.

The least significant address lines applied to the car picture ROM (inputs AQ, A1, A2 and A3) complement the rotation data code by determining which of the eight lines of the car is being described by the ROM data output, and whether it is the first half (right) or second half (left) of the car to be displayed. When ©2 is high, the video data output (VID 0 through VID 7) from the car picture ROM is timed with load vertical pulse LDV x B. Load vertical pulse LDV x B enables shift register M7 (K7 or H7) to load the video data from the car picture ROM. This data is for the right half of the car.

When ®2 is low, the video data output (VID 0 through VID 7) from the car picture ROM is timed with load vertical pulse LDV x A. Load vertical pulse LDV x Aenables shift register N7 (L7 or J7) to load the video data from the car picture ROM. This data is for the left half of the car. In review, the motion generator has received a RAM data code for where the car is to be displayed vertically and a RAM data code for the proper picture of the car. The final instruction needed is for the horizontal placement of the car. The RAM byte that determines this is received by the car horizontal location counter.

The car horizontal location counter R5 and R6 (P5 and P6 or N5 and N6), is loaded each horizontal line by a load horizontal pulse LDHx. The counter is preset to a given count by the RAM data code (DIS- PLAY 0 through DISPLAY 7) during horizontal blanking. At the end of horizontal blanking, 256H goes high, and the counter is enabled to begin counting up. at a clock rate of 6 MHz.

When the horizontal counter reaches its maximum count (all outputs are ones), it generates a “carry out” at pin 15. This carry pulse enables the car video shift registers M7 and M6 (K7 and L7 or H7 and J7) to begin shifting out the appropriate video previously loaded into it. The output of shift register N7 (L7 or J7) is now serial car picture information ready to be displayed as video. Video Output The video output circuit receives all video signals and gates them together through summing resistors R48, R49, and R50. Cars 2, 3, and the black video playfield are gated through resistor R49 to produce the black level video. Car 1 and the white playfield are gated through resistor R50 to produce the white level video.

Car/Playfield Comparator The car/playfield comparator is a network of logic gates that gate together the three video outputs of the motion generator and the two video outputs of the playfield generator. Table 4-2 provides the seven pos- Table 4-2. Conditions of Car/Playfield Data Output

. rn Data Line Car/Playfield Comparator Conditions Output

Car 1 Coincident with Car 2 or 3 D6 Car 1 Coincident with Black Playfield (oil) De Car 1 Coincident with White Playfield (track) D7

Table 4-3 Operation of Multiplexer M8 with Given Input Address

Address Logic Level Output ADR6 ADR7 1¥ (D7) 2 (D6)

LL102C0
LH1C12C1
HL1C22C2
HH1323

sible conditions that would cause a high to appear on data lines D6 and D7 of the data bus. The microcomputer MPU recognizes an output from the comparator by outputting an address to the Address Decoder for a COLLISION 1 or COLLISION 2 “read” signal. This causes tri-state devices E5 and E6 to be enabled and allows the output of the car/playfield comparator to be transferred onto the MPU data bus.

When the MPU receives the data that a skid (a high on data line D6) or crash (a high on data line D7) condition exists, program memory instructs the MPU to cause the appropriate response to be displayed on the TV monitor display. It then tells the MPU to clear the car/playfield comparator. This is done by the MPU outputting an address that is decoded to cause a low COLLISION RESET 1 and/or COLLISION RESET 2. The

Page 51

RIGHT TURN

LEFT TURN

L__ STEERING A (L9 PIN 1 OR 9)

STEERING B (L9 PIN 13 or 11)

STEERING A (L9 PIN 1 OR 9)

STEERING B (L9 PIN 13 or 11)

Figure 4-7 Steering Printed Circuit Assembly Output Pulses Collision Reset signals reset latch H6 of the car/ playfield comparator.

Manual Control Interface The main component of the manual control interface is multiplexer M8. This component acts as a two-pole four-position switch, operated by address lines ADR6 and ADR7 from the microcomputer MPU. Table 4-3 lists the input/output relationship of multiplexer M8 with the given address inputs. Multiplexer M68 interfaces three different sources of information as follows: 1) coin information, 2) steering information, and 3) switch information. All information is received by the microcomputer MPU when the MPU addresses the address decoder for a low SWITCH signal that enables tri-state device K5 for adataoutput on the D6 and D7 data lines of the MPU.

Coin information is .a matter of storing in the microcomputer RAM the number of times alow pulse appears on the data lines, when the appropriate address input of multiplexer M8 is being addressed. The microcomputer MPU only “looks” for coin pulses during the attract mode. Steering information is “looked” for by the microcomputer MPU during the play mode. The steering printed circuit assembly consists of two lightemitting diodes that are optically aligned with two light-sensitive transistors. A toothed cylinder, turned by the steering wheel, is inseted between the lightemitting diodes and the transistors, and interrupts the light from the diodes. When the steering wheel is turned, two pulses appear at the output of the steering printed circuit assembly that differ in phase.

As illustrated in Figure 4-7 when the wheel is turned to the right, the A output pulse leads the B output pulse. When the wheel is turned to the left the A output pulse lags the B output pulse. The inverse of the two pulses are applied to the D and clock inputs of two D-type flip-flops (see schematic). The microcomputer. MPU recognizes that a steering maneuver has been made when a low appears on data line D7. The MPU then “looks” at data line D6 and determines from the logic level (high or low) if “Steering A” input is leading or lagging “Steering B’ input. Once the MPU has processed a steering maneuver, the MPU then outputs an address that is decoded by the Address Decoder and results in a low STEERING RESET 7 or STEERING RESET 2 signal that resets the D-type flip-flop responsible for the steering signal.

Table 4-4 MPU Addresses For Reading Switch Status

MPU MPU

Address Switch Name Data Line

(in hexi- Used to decimal) Read Switch

0828First GearD7
0829Second GearD7
082AThird GearD7
082BGas PedalD7
082CSelf-Test SwitchD7
082DStart SwitchD7
08301- or 2-Lap OptionD6
0830Oil Slick OptionD7
0831Coin Option AD6
0831Coin Option BD7
0832Spare (Unused)D6
0832Extended Play OptionD7
0833Game Time Option AD6
0833Game Time Option BD7
Note: A low signal on the MPU data bit listed at the MPU address specified (in hex) indicates a switch closure.
Page 52

Switch information is received by multiplexer M8 and inputs 1CO and 2CO. The microcomputer MPU addresses Decoders H9 and J9 to determine if a switch is opened or closed. If closed, a low pulse will result for the given address as listed in Table 4-4.

Motor Generator The key to the motor generator is the operation of transistor Q1 in conjunction with timer D7,8. Timer D7,8 operates as an oscillator with output frequency dependent upon the resistive charge path of capacitor C22.

Varying the collector-to-emitter resistive value of transistor Qi varies the combined resistive charge path of capacitor C22 through transistor Q1 and resistors R21 and R23, in parallel with resistor R22. As the combined resistive value decreases, the output frequency of the timer increases. Variable resistor R23 makes it possible for the technician to adjust the frequency for a desirable motor idle sound.

Note: Resistor R22 is placed in parallel with this resistive charge path. Even if there is no current through the transistor, there will still be an alternate current path, so that the frequency of the oscillator will always equal idle frequency at least.

The conductance of transistor Q1 is determined by its available base current. The current is controlled by adigital-to-analog conversion. This conversion is accomplished via latch D4 and resistors R5, R6, R7, R8 and R9. The input tothis D/A converter is stored in the MPU RAM, and is accessed at the appropriate time by a “latch pulse’ labeled MOTOR 1. Table 4-5 shows the 16 possible voltages that will appear at the base of Q1 in conjunction with the appropriate data codes stored in the MPU RAM (DISPLAY 0 through DISPLAY 3).

To derive a realistic car motor sound, the output of timer 07,8 is divided into three separate frequencies by counter D8, then summed by resistors R42, R43, and R44. A divide-by-three signal at QB (pin 11) output of D8 is applied to summing resistor R42. Outputs QB and QD (pin 8) are also applied to Exclusive OR gate C7 to provide a divide-by-twelve signal at the QA (pin 12) output of D8, which is applied to summing resistor R42.

Bang and Screech Generator The heart of the bang and screech generator is noise generator B7, D7. Shift registers B7 and D7 are connected in a manner to produce random noise at the QH (pin 13) output of B7.

Bang is the result of data from the microcomputer RAM, which is used to gate varying amounts of random noise through to the audio amplifier via latch C4 and AND gate C5. Noise is gated from noise generator B7, D7 through a digitally-controlled resistive network consisting of R24, R25, R26, and R27. The result is an envelope of sound from full on to full off.

Screech sound is produced by processing the output of the random noise generator with a type of hysteresis feedback loop, via Schmitt-trigger inverter AS (7414) and 100-ohm resistor R17, and then gating this processed noise with SKID 1.

Audio Output The summed signals of the motor generator and bang and screech generator are applied to one leg of a 5k-ohm potentiometer. Varying the wiper position of the potentiometer varies the signal input of audio amplifier D9. The output of the audio amplifier is connected to an 8-ohm speaker.

Table 4-5 Approximate Base Voltage of Transistor QI or Q2 for Given Address

Base Voltage of \Transistor Q1 or Q2 Address

L AV1dSIG

0 AV1dSIG

7 AVIdSIC € AVIdSIG

5.00 VDC 4.25 VDC 4.08 VDC 3.95 VDC 3.77 VDC 3.65 VDC 3.52 VDC 3.42 VDC 3.22 VDC 3.13 VDC 3.03 VDC 2.95 VDC 2.84 VDC 2.77 VDC 2.69 VDC 2.62 VDC Deteteteteririeier Doerr tier iter iter DoIDIrrre tit teeree TrrrrrcrmiRererrererrer

Page 53

ILLUSTRATED PARTS CATALOG

The purpose of this chapter is to provide you with the necessary information for ordering replacement parts for your Sprint One™ game (woodgrain or graphics version).

When ordering parts from your distributor, give the part number, part name, applicable figure number of this list, and the serial number of your Sprint One game. This will help to avoid confusion and mistakes in your order. We hope the results will be less downtime and more profit from your game.

\f there are any questions about this catalog, please contact Atari’s Customer Service Department by telephone Monday through Friday, from 7:30a.m. to 4 p.m. Pacific Time. From California, Alaska and Hawaii, call (408) 984-1900, from the remaining 47 states call (800) 538-6892, toll-free.

Page 54

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction torbidgen without the specific written permission of Alar. Inc.. Sunnyvale California, This drawing is only conditionally issued. an neither receipt nor possession three! conters ar transfers any cight in. or license 10 use, the subject matter of the ‘drawing or any design oF echnical formation shown {herean.nor any right to reproduce inis drawing or any part thereot. except for manulactura by vendors of Atart INcOr porated ana for manulaciure under the corporation 3 wrt feniicense.no right lo epraauce mis drawing is granted or the subject matter thereot uniess by written agreement wnt oF written permission trom the corporation

Page 55

2€0.@4)/ !

Leoe wens

A-—— ITEMS NOT CALCED OUT) ©©8® | e ZEA. &)

Figure 5-1 Sprint One Final Assembly A00887 2-01 Cc

Page 56

} 4 Warner Communications Company Figure 5-1 Sprint One Final Assembly Parts List

ItemPart NumberQty.Description

i i

aEA008873-011Cabinet Assembly
2A008874-011Control Panel Assembly
3A008875-011T.V. Shelf Assembly
4A007299-011Rear Door Assembly with Lock
5A009262-011R.F. Shield Box Assembly
6AQ08919-Xx1Shipping Container Assembly
7A007258-011Power Supply Base Assembly, Type "C"
8A009083-011Coin Door Assembly
9005419-011Speaker Mesh Cover
10002728-012Brkt. Control Panel
11006870-011Coin Box Bracket
12008901-011Bezel, Cardboard
13008903-011Shield, Plex Cover
14006311-011Harness, Schematic
15A006446-011R.F. Shield PCB Assembly
*16A006443- 021P.C.B. Assembly, Sprint I (ROM Version)
17005233-011Rear Door Seal
18006319-011Copyright Decal
19006305-011Printed Poly Bag
20TM-0951 Hl Tech. Manual
21007193-01LOn/Off Switch Cover
22008906-011Cover Panel, with Graphics
23A008845-011Single Foot Pedal Assembly
2478~-240074Cable Tie, Heat Stablized
2581-7022Tip-N-Tell Indicator
2678-66012161Alum. Foil, 1" Wide x 20" Lg. (Approx.)
2773-770044Rivets, 3/16" OD x .68 Lg. (.250 - .500 Grip)
2848-0091Speaker, 8"
2982-80166Screws, Button Hd. Socket Cap. #10~32 x 1.00" Lg.
3075-990900066Well Nuts, Blind Hole Fastener #10-32
3175-5524B4Carriage Bolts, %-20 x 1.50 ig.
3275-5516B4Carriage Bolts, 4-20 x 1.00 Lg.
3375-0456Washers, Split-Lock 4
3475-0158li | Washers, Flat %
3575-91582Hex Nuts, 4-20
3675-9354Wing Nuts, 4-20
3782-18248Wood Screws, #8 x 14 Lg. Ft. Hd. Phil.
3872-661020 | Screws, Sm. Pan Hd. Phil. #6 x 5/8 Lg.
3972-6608°| Screws, Sm. Pan Hd. Phil. #6 x 4 Lg.

*A substitute for Item 16 is A006423-01

Page 57

Figure 5-1 Sprint One Final Assembly Parts List

DESCRIPTION

Screws, Sm. Pan Hd. Phil. #8 x % Lg- Screws, Sm. Pan Hd. Phil. #8 x 3/4 Lg. Screw Down Tie-Wrap 78-25001

4346-201302Fuses, 3 AMP
44A007902-01Cash Box Assembly
451pc-095Illustrated Parts Catalog
46ST-095Self Test Chart

47 A009063-01 48 A006312-02 49 A009509-01 50 A033016-01 Speaker Harness Assembly Main HarnessAllembled To Volume Control Power Switch & Harness Assembly Strain Relief Power Cord Assembly PPP EPP Ee Ne Be

5275-990505S44-20 Nylon Locknuts
5375-070216#10 Nylon Black Washers

* A substitute for is A006443-01, Qty of 1, PCB Assy, Sprint 1 (ROM Version)

© A vvainer communications Company

Page 58

section AN

AX Ac res oe pants, pomiesen oy rus mpmen SWLL BE FITTED FOR CARTET ASSENLY, BIT SLL AT Be PEMWUCATLY IRSTALLED,

Figure 5-2 Cabinet Assembly A008873-01 A Ae NOTICE TO ALL PERSONS RECEIVING THIS ORAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari. inc... Sunnyvale. Caltornia. This drawing 1s anly coneitianally ssued, ane neither racist nor possession thereat contersor transters any right in. oF license to use, the subject matter of the Grawing oF any design or technical information shown thereon. norany tight o reproduce this drawing or any part thereot. except for manufacture by vendors of Atari Incor porates ans for manufacture under the corporation's writ fen license. norigh 1erepreduce his drawing is granted or the sudject matier thereef unless by writen agreement with of written permission fram the corporation

Page 59

AL ATARI’ Figure 5-2 Cabinet Assembly Parts List

ItemPart NumberQty.Description
1A008877-011Left Hand Side Panel Cleat Assembly
2A008877-021Right Hand Side Panel Cleat Assembly
3A008878-01LLower Control Panel Assembly
4A008879-011Foot Pedal Box Assembly
5A007298-01Ref Rear Door Assembly
6008908-011Panel, Top
7A008876-011Panel, Speaker Mounting Assembly
8008895-011Panel, Plex Support
9008897-01Ref T.V. Mounting Shelf
10008898-01Ref Panel, Control Support
11008881-011Panel, Front
12008896-011Panel, Base
13008882-011Panel, Lower Rear
14008883-011Panel, Upper Rear

© A Warner Communications Company

Page 60

(Q 2 REG'D (2)

“2 ©)

(© +a. (i?) 4 ReaD. @) 4 READ

Figure 5-3 Control Panel Assembly Cc A008874-01

Page 61

ATARI Figure 5-3 Control Panel Assembly Parts List

Description

Control Panel with Graphics Control Panel with Wood Support Assembly, Control Panel Harness N-Shift Assembly See Figure 4 Steering Wheel Assembly See Figure 5

Screws, #10-24 x 3/4 Lg "F" Type Phil.

Carriage Bolt, 4-20 x Ls Lg.

Washers, Split-Lock ¥

Screw, Sheet Metal, #6 x 5/8" Lg. #10 Split-Lock Washers

ItemPart NumberQty.

——_+-

1008902-011
2008898-011
3A006313-011
4A000608-021
5A000598-02L
6000567-011Bow Washer
7001856-011Bushing Alum.
8005255-011Shift Bezel
985-22F1121
1062-0021LED Switch
ll75-55242
1275-015S2Washers, Flat &
1375-0452
1475-915S2Hex Nuts, 4-20
1575-66102
1675-0401
1775-010810

© A Warmer Communications Company Washer, Flat #10

Page 62

VA waren (eM 4) REMOVED

FO SHOW RIVET CTEM A),

ens]

Figure 5-4 N-Shift Assembly A000608-02 NOTICE 70 ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL” Reproduction forbicgen without ine specific written permission of Atari, Inc.. Sunnyvale. California. This drawing is only conditionally issued, and either receipt nor possession tnereo! conters or transfers, Any right in, ar license to use, the subiect matter of the rawing or sny design or technical information shown thereon, nor any right to reproduce tnisdrawing or any art tmereot. except for manutacture by vendors of Atal Incorporated and for manutacture under the corporation's writ tenlicense. no right to reproduce nis drawings granted oF the subject matier thereot unless by written agreement with or written permission fom the Corporation.

OMIT THIS SWITCH CITEMG)

Page 63

A ATARI Figure 5-4 N-Shift Assembly Parts List

tem Part Number DESCRIPTION

1 000609-01 2 A000610-01 3 005671-01 4 73-7C0307SH 5 78-3002003 6 65~021A 7 75-046 8 75-044 9 85-22F412 1o 85-22F 608 11 76-113758 12 78~-16002 13 78- 33001 gu H lo

Ooo tunwrnn Shift Housing Handie Assy Shift Detent Shift Rivets Spring, Assoc. Spring Co. (Co 360-032-100M/W) Switch, Cherry (E18-00M) Washers, #6 Split-Lock Washers, #4 Split-Lock SCR Mach., 4-40 x 3/4 Lg. Pan HD., Self Threading Ty| SCR Mach., 6-32 x kLg. Pan HD., Self Threading Type Ball, Steel, 3/8 Dia. Bearing Grade Silicone Compound, Dow Corning #5 Clamp, Hose

NOTE; Item #13, 78-33001, Hose Clamp is to be used only with old shift housing P/N 000609 Rev. "D eo “Ft ope
Page 64

Figure 5-5 Steering Wheel Assembly A000598-02 NOTICE TO ALL PEASONS RECEIVING THIS DRAWING CONFIDENTIAL: Aeproduction forbidden without the specific writlan permission of Atari. Ine. Sunnyvale California, This draming #8 only conditionally sued. and nether receipt nor possession ihereot confers translers, any right im. of license to use, the subject matter of the drawing or any design oF technical information shown thereon. nor any right fo reproduce this drawing or any part inereot, excep! for manutacture by vendors of Alar INcor porated ana for manutaclure under the corporation's writ {on license, no night to eproducethis drawings granted or the subject matter thereot uniess By written agreement lenin or wnilten permission trom the corporation

Page 65

Figure 5-5 Steering Wheel Assembly Parts List i

ATARI

temPart NumberQty.DESCRIPTION
1A000598-02Ref | Steering Wheel Assembly
2002133~021Cover, Kee Games Logo
30006051Housing
40006061Shaft
585-22F2062Scr. Sht. Metal, #2-56 X 3/8 'F' Type
672-75123Mach Scr, 4-20 x 3/4 1g, Fillister Hd Slotted
7A0006071Printed Circuit Assembly See Figure 6
875-070022Washer, Fender, %
976-0920201Bearing, Thompson (20L20-FK)
io76-0910101Bearing, Thompson (10L10-FK)
1178-401041Steering Wheel, 10"
1275-990505 81Nut, 4-20, Nylon Lock, Shallow Pattern
1372-95801Mach Scr, 4-20 x 5 Lg, Truss Hd, Slotted
140006161Hub Light
1575-0551Washer, %" Int. Tooth, Starlock
1675-O4Z2 |Washer, Split Lock #2
Page 66

Figure 5-6 Steering Board Assembly A000607 M

TRACES ARE OWN OPPOSITE SIDE

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING. CONFIDENTIAL: Aeproduction forbidden without the specific wrillen permssion of Atari. Inc.. Sunnyvale. Cal or license to use. the subject matter of the ar ‘any design or lechnical information shown thereon, ner any right reprocuce this drawing orany part

with oF written permission fram the corporation

Page 67

Figure 5-6 Steering Board Assembly Parts List

ATARI’

= —— Item | __ Part Number | Qty. Description |

1009061-011P.C. Board
210-51012Res., Carbon Comp., %W, 5%, 100 Ohm R 8,9
310-515127""" " 150 " R1,8
410-53322.7=i " 3.3k " R 6,7
510-54714"":- " 470 " R 2-5
627-2501032Cap., Cer, Disc., 01 uf, 25Vc1,2
Ei34-2N36432Transistor, 2N3643 9 1,2
879-580051Connector, 10 position
9030369-011Radial Optical Coupler

rw) ‘A Warner Communications Company

Page 68

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING iL Reproduction forbiaden without the A permission of Atari, Ine.. Sunnyvale, California. This drawing Is only conditionally issued. an neither receipt nar possession thereat confers oricansters any right in. ar license to use, the subject mater of the raming thereon. nor any right to reproduce th's drawing or any part thereat. except for manufacture by vendors of Atari Incor poratec and for manufacture under the corporation's writ {en license, no rightto reproduce this drawing 'sorantea or the subject matter thereo! unless by written agreement with ar written permission from the corporation any design or technical intormation shown

8)ouT

' I '

  • + - + a S)+sv

Ra RI R2 Re R4 es 410 150 410 1SO ATO 470 ci | a4 -Ol

rot) Qi ANRC l

Figure 5-6 Steering Board Schematic Diagram

Page 69

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 70

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbldder without the specific writien permission of Atari, Inc... Sunnyvale, California. This drawing is only conditionally ‘ssued ane Neither receipt nor possession thereat confers or transfers any right in, or license to use, the subject matter of the Srawing oF ary design or technical information shown thereon. nor any right fo reproduce this drawing or ary part thereof. except for manulacture by vendors of Ata I-corporated and for manufacture under the corporation's writ fen license, no right to reproduce this drawing’s granted! or tine subject matter thereot unless by written agreement with or written permission trom tne corporation.

Figure 5-7 TV Shelf Assembly A008875-01 A

Page 71

A. ATARI" Figure 5-7 TV Shelf Assembly Parts List

Item Part Number Q Description

1 008897-01 2 92-032 3 75-5120 4 75-040 5 75-911S 6 75-010S 7 82-405 8 75-07002 9 75-045 10 75-9158 11 72-6012 12 75-015S BNNNNNAARBREH Panel, T.V. Shelf 23" T.V. Monitor Carriage Bolts #10-24 x 1.25 Lg. Lock Washer #10 Hex Nuts, #10-24 Flat Washers, #10 Eye Bolts, %-20 x 3" Lg. Flat Washer 4, Fender Lock Washers, Split % Hex Nuts, 4-20 Screws, Sm. #10 x 3/4" Lg. Flat Washer, #%

a a iw’) AWarer Communications Company

Page 72

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIA: Raproduction forsidden without the specitic written permssion of Atari, Inc.. Sunnyvale, California. This drawing ss only conditionally issued. ene neither receipt nor possession thereo! confers or transfers {ny right in, oF license to use, the subject mailer of the drawing of any design ar technical information shown thereon. nor any right to rapraduce nis crawingar any part thereot. except for manulacture By vendors oF Atari incor porated ang for manutacture under the corporation's writ ten license, na right io repraduce this raving Is granted or the subject matter thereaf unless by wntien agreement with oF written permission from the corporation OOOO

©

Poe) loo oo a for. Bob q

MGV VOCTAGE SELECTION BLOCK SHOWN e090

) g

fon

@) 2 acco} 3 o

Figure 5-8 Power Supply Assembly A007258-01

Page 73

AL ATARI Figure 5-8 Power Supply Assembly Parts List

© + Warner Communications Company

ItemPart NumberQty. LoDescription
1A009266-011Power Supply Base Weldment.
2A006886-021Transformer Termination Assembly “Type C”
378-2708alGrommet, Plastic
4A006958-01A/RVolt Sel Block, 95V
5AC06958-02=Volt Sel Block, 110v
6A006958-03"Volt Sel Block, 205V
7A006958-047Volt Sel Block, 220V
879-44110045Fuse Holder, Panel Mounting
9gA007192-01LPower Switch Termination Assembly
loA007444-011Power In Harness
ii41-20031Filter, Power Line, 5 AMP
1275-0486Washer, Split Lock, #8
1375-918S6Nut, Mach., Hex, Steel #8
1472-1810S6Screw, Pan Hd., Steel #8-32 x 5/8" Lg.
a5.75-01888Washer, Flat, Steel #8
1646-203801LFuse, 8 AMP, 125V, 3 AG Fast Acting
1746-2012512Fuse, 2%: AMP, 125V, Slow Acting
Page 74

Figure 5-8 Power Supply Schematic Diagram rt NS mT] OM De CEs L MS asO-NO se TOS Te Mm LS ™ CIT é38ha

MS DDOAWEINI L ak dl | NS Z| NO ANNI Lno ASI

D c ino A SII

90d waMod [2 |? [tm t= 0550 bame

NMOHS

2078 NOULDE73S BOVINON AOU

AQ Dp oe OUI B93c04 AD i> of —_ KP AS” Ps | san'3e) Agoe | HE/A | BOeaeAy BO! Koza Tw ~~ Yeni an MEWUOISNVEL

$5 ow by o—

Page 75

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 76

Ge) \ gs : © 2 PLCS QI) : : af ioe

2 PLCS @)

Oo)

4 PLCS (2)

YEL YEW/BK (2)4 PLCS BK/YEL

nell an ny "ight sf, oF Hicense to use, the subject matter ol the ‘Srauing or any sesign or technica. iormation show thereon, ior any ign to reproduce this drawng or any pat thereof, except for manufacture by vendors of Atari, incor porated and for manutecture under tne cosporation's wnt farlicenga, no right reproduce hrs draing is yraniea the subjéct matte: thereof untess by wiiten agresment ‘wite oF wiltten permission trom the eoeparation.

Figure 5-9 Coin Door Assembly A006794-01 through -07 F

  • 2 PLCS
  • 2 PLCS Qt) 2 PLCS

Qi) 2 PLCS

Page 77

Figure 5-9 Coin Door Assembly Ih Parts List ATARI

| ItemPart NumberQty.Description
1 i 4007637-011Front Bezel Assy. - Used only on -01 Coin Door Assy.

A007637-02 Ref.] Front Bezel Assy. - Used only on -02 Coin Door Assy. A007637-03 Ref.] Front Bezel Assy. - Used only on -03 Coin Door Assy. A007637-04 Ref£.| Front Bezel Assy. - Used only on ~04 Coin Door Assy. 007637-05 Ref£.| Front Bezel Assy. - Used only on -05 Coin Door Assy. A007637-06 Ref.| Front Bezel Assy. ~ Used only on -06 Coin Door Assy. A007637-07 Ref.| pront Bezel Assy. - Used only on -07 Coin Door Assy.

275-91654Nut 6-32
3030362-O11Coin Lock-Out. Assembly
4A007640-012Coin Switch Assembly
5A002465-01LCoin Counter Assembly
6004320-011Coin Door Weldment
7004341-012Secondary Coin Chute
8004344-011Key Loop
9004340~012Spring-Return
10004337-01FBracket, Wire Form
11004338-011Lock+Out, Wire Form, R.H.
12004336-011Lock-Out, Wire Form, L-H.
13004326-012Button, Scavenger
1475-046¢Lock Washer, #6
15006904-012Spacer
16007359-011Lamp Socket
770-11-471Lamp
1873-30082Retaining “C" Ring, Trnarc #5103-25
1975-99140016Self-Vmeading Nut, Tinmerman #SR786006
2075-02684Washer #6
2175-00516a3Kepnut, Style 842, Stl., 6-32
22008629-012Spring
2371-21181Lock Assembly, Hudson Lock
2471-1225CU2Coin Mechanism for American Quarter only

71-1205FF Ref.| Coin Mechanism for Belgian 5 Francs Only 71-1201MG Ref.| Coin Mechanism for German Mark only 71-1201KS Ref.} Coin Mechanism for Swedish Krona Only 71-12100vo Ref.| Coin Mechanism for Japanese 100 Yen Only 71-1210PE Ref.| coin Mechanism for English 10 Pence Only 71-1220CA, Ref.| Coin Mechanism for Australian 20-Cent Piece only

25007753-011Plate, Anti~Probe
264007638-011Switch Assembly - Slam
27A006921-011_|_ Harness Assembly
Page 78

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 79

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 80

fe) te) oO Oo

KLMNPRSTUVWKYT aes o00000

ROW 2 a

888888 ROW 14 meat

0009 0000 88 88888 > ROW 2

oboo ©000 1234567 890112134 Bot 1S 1920222 le)

ITEM 7, fo PLACES

RF Shield PCB Assembly Figure 5-11 B A006446-01

Page 81

AL Figure 5-11 RF Shield PCB Assembly

Parts List

ATARI’

[item] Part Number | Qty. Description

1005491-017PC Board
279-5172221Connector, 44 Pin P.C. Mount
341-30036Inductor, 100zh Large Case
427~250104ig | Cap, Cer. Dise O.tpf 25V
5.52-0028Jumper, .4 Center
652-0032Jumper, .6 Center
727-A2501046Cap, Cer Disc 0. luf 25V

L

Page 82
  • “s3u ‘.uonjetodson at spun 9unI2e}FUEW 10) pu OB\eI0d 1O3U iy Jo sOpUBA AQ erMDeIMUEUl 40} 0BOKA Joasut "eolu3a] 19 UBISep AUB 30 BwMep voneiodie9 24) wor uorssiused uaxuM 30 ule g

g z sd Aue io 6unmerp 43 9°PO1d0: 0} 4B AUB JOU Joan

ue -panss Al ‘sjenkusns, mous

  • 5028 siejsuen.

aunneenee 30-eoto

ion | O-

woad fea) alon[ rnlon|inlorfia g

r —t

B) loocaan §_| [El cocaes = B|Blooez30 1/12 looe2si eer : osid aa B00OaF eV aT Figure 5-12 Sprint One PCB Assembly A006433-01 and-02. C

Page 83

A ATARI’

Parts List -01 Version Figure 5-12 Sprint One PCB Assembly

Description Ttem | Part Number | Qty. FN (030626-01 1 2 10-5102 2 3 yo-5102 20 4 10-5108 n 5 10-5105 a 6 10-5182 2 7 10-5222 3 js 10-5224 a 9 10-5225 1 10 10-5331 3 a 10-5333 Fl cry 10-5335 1 13 19-5392 ja ary 20-5471 3 as 20-5474 a 1s 10-5683 1 uv 30-5822 1 qe 119-808WAPO 1 qs 19-313802 2 20 | 1g-315254 | | 2 22 10-5270 1 25 2i-101103 1

!

Sprint One P.C. Board Res., Carbon, 5%, 'ii 100 OHM

ie 470" 470K * eax" Res., Wixewourd 10W, 4 ORM Trimpot, 5K OHM fximpot, 250K OHM Res., Carbon, 58, kW 27 OHM cap., mylar, -Oluf 100v

RAT, 35 B1,2,4,19,26.33,38,50 68537 R3,21,31,42-44,58-61, BB R6 RAB, 49 RIS, 16/25 RB RS RAS , 46 ,51-53, 77-83, 86) R62 R24 R87,55,57 RT Ro Ra7 R66 B23 RES,

» & Part Number

Description aa a 4a sl

24-160808 24-250106 24-250108 24-250227 24-250478 27-250102 27-250103 27-250104 27-250224 28-101101 2a-101221 31-AL4F 3L-HR750 31-1NS14 33-2N3644 34-2N6044 37-7400 37-7402 37-7404

Cap., Electrolytic, 8000uf, 16v ” i lous -25v ” . looouf 25 . ” 220uf 25V " " 4700uf 25v cap., Ceramic Dise, -O0luf, 25v " “lowe sv " "aug 280 . ey \22uf 25 Cap.. Dipped Mica, 100p£, 100v ” "= -320p€ Ieow Diode, Alar Diode, MR750 Dicde, 1N914 Transistor, 2N3644 ‘Transistor, 2N6044 Integrated Circuit, 7400 : x 7402 ” "7408

65,66 c17,18,25 cag c1z cs? ess C28, °,57,44,45, c1-3,5,13-16, 19-2 26,27, 31-36 41-43 48,51,52,54,56,39 6-11,79,68,69 cm. R6,7 cra,s cri, 2 Qn F8,D0 Pz ERE4 ,W5,I5,16,N9 QD 22 Conmiresions Company

Page 84

Figure S-12 Sprint One PCB Assembly Parts List ATARI -01 Version Item | Part Number | Qtv. Deseription Ttem | Part Number | Qty. Description 60 37-7408 5 || tntograted Circuit 7408 52,C2,N3,CE.A6 95 61 37-7410 L 7410 RT 96 62 37-7414 2 7414 AS 19 97 62-001 1 || switen, sPst, Momentary a3 63 37-7420 1 . "7420 aa 98 64 37-1430 a . "7430 Na 99 e6-LleP17 1 || Switch, spst, xe, DIP sw, 65 37-7432 5 . “7432. -A2,L2,P3,76,38 100 66 37-7437 a ‘ "7497 RS aol 67 37-7474 2 ” 7476 RL M9 102 ee 37-748 74 a asta Re 103 | 72-2608¢ 2 || Screws, Pan Ha., Phil., 6-32 x4 Ig., CRES 6 37-7475 2 7475 ca,04 10a | 75-016 2 || Washer, Flat #6 70 37-7483 2 . “7483 Lama 105 | 75-056 2 || washer, Lock, Int. star, #6 n 37-7486 1 . “74867 aos | 75-916c 2 |} wut, Hes, #6-32 cRES R 37-7490 a . "7490 6/7 107 3 37-7492 a " "7492 pe 208 4 37-9312 5 " "932 Ro ios | 78-0601 a |] Heatsink, (24323) 75 37-74153 L 7 "74153 MB aio | 78-96009 1 || Heatsink, (roa1004) 16 37-74156 FY . 7415639 au | 78-1306 n/a || cement, (201004 Heatsink) n 37-741s163, 6 * 7418163 -NS,P5,R5, _N6,P6,R az | 7816005 a || sitpaa coms23) 78 37-74168 2 " 74164 B7,07 113 9 3727418165 6 - *7gUSL65—N7,47,97,87,07,07, aaa

us 60 37-7416 1 ” "aes RB 146 al 37-74174 3 . “741745, 5,R7 aw 82 37-74175 1 " “7417s m2 aie 83 sre TAzIS 2 . “74279 He a9 | 79242040 1 || Socket, 40 Pin, Med. Insertion 3, a4 37-9301 5 . 9301 2, F2,27,28,K8 io 8s 37-9316 5 . 9316 R2,L3,M3,88,P8 joi 96 37-9322 \3 ” 9322 H2,2,K2 be er 37-9334 u sea oHB az3| 90-202 a |) ceystai 12.096 v1 as 37-555 1 $55 v7/8 29 37-74367 3 . "7436785, KS,E6 is 90 90-7020 a . "mina 23/H8,93, 43,84, 54,04, is | Pr a i. []ptaguiteer, ates at} 006434-01 a |) sprint x Program Prom qi 92 37-7DA1004 a |} op-ase DA1004 D9 aze | 006435-01 1 || sprine r Program Prom 2 Lo 3 129 | 00846~01 a || sprint 1 program Prom 3 m oa 130 | 006437-01 1 || sprint 1 Program Prom 4 wo

Page 85

ATARI: ‘item

Part Number

Figure 5-12 Sprint One PCB Assembly

Parts List -01 Version

Description

Ttem

Part Number

Description ai 135, uw aan 14a a7 1as asi 1s2 asd 355, as? ise ase asi

006436-01 006439-01, 006440-01 006441-01 006396-02 006397-01 006398-01 (006399-01 906400-01, 006401-02,

Sprint t Program Prom 5 Sprint 1 Program Prom 6 sprint I Program Prom 7 Sprint 1 Program Prom 6 Sprint Character Prom LS3 Sprint Character Prom MSB Sprint Race Car Prom LSB Sprint Race Car Prom MSS Sprint sync Prom Sprint Adress Decote Prom

mL no Pl PO Pa Ke £2

006290-01 006291-01 90-6010

sprint Race Trak Rom 1 Sprint Race Trak Rom 2 Integrated Circuit

BL ct

Page 86

A,

Figure 5-12 Sprint One PCB Assembly Parts List -02 Version ATARI" ‘Part Number 1 030626-01 2 20-5101 3 10-5102 4 19-5109, 5 10-5105 6 10-8182 7 10-5222 8 19-5224 ° 10-5225 10 10-5331, un 10-5333, 2 10-5335, 1s 10-5392 4 19-5471 15 10-5474 as 10-5683 Ww 10-5822 18 19-808"4P0 19 19-315502 20 19-315254 aL 22 10-5270 25 21-101103

Quy. Description 1 | sprint 1 P.c. Board

  • |Res., carbon, 58, hit 100 o8 wf oy oe 8 aK ® ule se 20K tle oe my 2|° “8 eK 3 | mo 22K af 320K oe ee ee af 330» 1 " “aK * a PR FF gory rte * 3.9K" 3 "470" 1 . "470K" 1 | Res., wirewound 1oW, 4 ouM 1 | reimot, 5x oat 1 | reimpot, 250% ons 1 Res., Carbon, 5t, W 27 OHM a | cap., mylar, .oluf 100v

17,35 RL,2,4,19,28, 33,38, 50) 68,37 3,21, 31,42-44,58-61, R6 RAB, 49 RIS ,16,25 RB RS: RAS ,46, 51-53, 77-83, 86] R62 R22 R24 287,55,57 RT RO R27 RA?

24-160808 24-250106 24-250108 24-250227 24-280878 27-250102 27~250103 27-250104 27-250224 28-101101 28-101221 ai-auaP. 31-4750 31-1N914 33-2N3644 34-2N6044 37-7800 37-7402 37-7404

Cap., Electrolytic, B000uf, 16V 7 " gaf = _25v

. looouf 25v " " 220uf © 25 ” - 4700uf 25V Cap., Ceramic Disc, .00luf, 25V . " , oluf 26v . s * Ine 28y " w ™ 22ue 25v cap., Dipped Mica, 100pr, 100V . " * 220p€ Lo0v Diode, ALaF Diode, MR750 Diode, 1N914 ‘Transistor, 2N3644 ‘Transistor, 2N6044 Integrated Circuit, 7400 . "7402 ” "7404

65,66 617,18 ,25 cas c12 cer css 28, | 457,44,45 cr6,7 cra, 5 cr1,2 gu F8,D0 #3, 4/5 ,J5,L6,N9 © 1 Wo rce: Gammuneatons Company

Page 87

A Figure 5-12 Sprint One PCB Assembly Parts List ATARI” -02 Version Tem | Part Number | Qty. Description Ttem | Part Number | Qty. Description co | 37-7408 5 |[antesrated circuit 7408 — B2,C2,N3,C5,A6 95 61 37-7410 1 . 7410 RT 96 62 37-7416 2 " 741d A819 7 62-001 1 || Switch, seer, Momentary sw3 63 31-7420 1 . “7420 a8 98 64 37-7430 L 5 ¥ 7430 ‘NG 99 66-118P1T L Switch, SPST, x8, DIP ‘Swl 65 37-7432 5 . "7432 2,22,P3,F 6,08 100 66 a7-7437 1 . "7437 Ro 101 67 37-7474 2 . 7474 RAMS 102 68 37-748 74 1 ” 74874 RB 103 72-1608C 2 Screws, Pan Ha., Phil., 6-32 x 4 Lg., CRES 69 37-7475 2 . “7475 capa roa | 75-016 2 || washer, Fiat #6 70 37-7483 2 . “7083 Ldyma ros | 75-056 2 || washer, tock, Int. Star, #6 n 37-7486 1 . mas CT ros | 75-916c 2 || wut, wes, #6-32 cRES n 37-7490 1 7490 6/7 107 3 37-7492 1 . 7as2 a 108 4 37-9312 1 . "9312 Ho 103 | 78-0601 a || Heatsink, (19323) B 3774153, 1 . “7aiss Me 110 | 78-6009 1 || Heatsink, (rpa1004) 16 37-74156 1 . "74186 39 | 76-13016 lan || coment, (7pR1004 Heatsink) ” 37-7418163 6 . " 740s163—NS,P5,RS, _N6,P6.RI 112 | 7@-16005 a |] sitpaa am323) 78 37-74164 2 - " 7a164 87,07 3 19 a7-7ausi6s | 6 . "78165 NT.H7,37,K7,07,07, 1a

1s 20 37-74166 a "7416s RB hae al 37-74174 3 * 78174 FS,05,R7 a ez 37-74175, l "yas Ne us 83 lard v “ " itd #6 119 79-42 040 1 Socket, 40 Pin, Med Insertion 3 a4 37-9301 5 . "9301 2,82,27,28,K8 ie 85 37-9316 5 "9316 R2,23,M3,NB,PS a 86 37-9322 3 “9322 H2,02,K2 ie eT 37-9334 + 7 9334 #8 123 1 Crystal 12.096 YL 88 37-555 1 "555 7/8 ipa 89 37-74367 3 . "7436785 ,K5,6 1s 90 90-7020 8 ” " RULORA F9,H9,T3.K3, FAH Ay 126 91 37-1M323 a Regulator M323, a 92 37-TDA1004 1 Op-AMP ‘TDA1OO4 D9 128 = 129 a 130

Page 88

A ATART Part Number

Qty. Parts List -02 Version Description Figure 5-12 Sprint One PCB Assembly 006396-01 006397-01 006398-01 006399-01 006400-02 o06401-01 006442-01 006443-01

Sprint Character Prom zsB Sprint Character Prom MSB Sprint Race Car Prom LSB Sprint Race Car Prom MSB Sprint Sync Prom Sprint Address Decode Prom Sprint I Program Rom 1 Sprint I Program Rom 2

Pa x6 M2 DL BL

006290-01 00629102 90-6010

Sprint Race Trak Rom 1 Sprint Race Trak Rom 2 Integrated Circuit Oo ore conmncatosconsany

BL cl Item | Part Number __| @ty. Description

u L

Page 89

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 90

ZL kea'D (6

NOTIGE TO ALL PERSONS RECEIVING THIS PRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc.. Sunnyvale California, This éraaing is only conditicnally Issued, and neither receipt nor possession theteot confers ar transfers any right in, oF license 10 use, the subject matter 0! the Grawing or any design er techrical information shown thereors, narany right to reproduce this drawing orany pan thereoT, except for manufacture by vendors of Alar incor porated and for manufacture under the cerporation's writ tenlicanse, ne tight to reproducethis drawings granted or the subject matter therecf unless by written agreement with or wetten permission from the corporain, ~ Secore Ih Final SSCEMEY — >

Figure 5-13 Single Foot Pedal Assembly with Harness Assembly A008845-01 c

Page 91

Figure 5-13 Single Foot Pedal Assembly with Harness Assembly Parts List ATARI

ItemPart NumberQty.Description
1A007183-01LFoot Pedal Assembly
2A008955-011Harness Assembly, Foot Pedal
3A009804-011Assy, Micro Switch & Bracket
475-0462Lock Washer #6
575-916S2Nut, Hex, #6-32
775-0432Washer, Split-Lock, 5/16"
875-915S24"-20 Hex Nut
975-5524B2Carriage Bolt, Blk, k"-20 x 1.50"

© 4 Warner Communications Company

Page 92

\ \ / ( LLLEAN ARROW JF Figure 5-14 Sprint One Final Assembly (Graphics)

A03283701 D

Page 93

Figure 5-14 Sprint One Final Assembly (Graphics)

Parts List

SO he Item |__ Part Number | Qty. Description

42 | a009509-01 1 | Power Switch s Harness Assembly a3 75-07021 6 | #20 nylon Black Washers | 44 81-095 a1 | sei Test chart 45 | M095 1 | Tilusteated Parts Catalog @ Tech. Manual 46 al-702 2 | tip--re11 Indicator a7 008233-03 1 | Rear Door Seal 40 | agosgo1-xx 1 | shipping Container Assexbly 49 75-55248 4 | Carriage Rolts, 4-20 X 1.50 Lg. {Plack) 50 006305-01 1 | Printed Poly Bag {5 75-9702 2 | washor, Flat Tenn _Pem Nissen [aor Ginn n gubstivute far reer] @ ts ROQS432-OL, GRY. of 1, F.C.B. Rew'y., Sprint T, iy [ acszeao-01 | 2 | Cabinet Aes'y. with Graphics 2 | A032837-01 1 | Control Panel Assembly 3 | aoosaas-o1 1 | Single Foot Pedal Assenbly 4 | n032638-01 1 Display Assembly 5 | Acoss8s-o1 1 | Sliding 7.V. shelf Assembly 6 | Aoos262-01 1 | R.F. shield Bex Assemb3y j 7 | roosaas-o1 1 | RF, Shield P.C.s. Assenbly +8 | x006433-02 1 | PiclB. Assembly, Sprint 1 (Rom Version) 9 | a0o7258-01 1 | Power supply Rase Assembly, Type x0 | aco30a3-o1 1 | coin Door assenbly i a 903053-01 2. | Hetainers, Plexiglas | 12 75-99090096 6 | Weli-nuts #10-32 3 82-8016 6 | Screws. Button Ha. Socket Cap. #10-32 X 1.00" Ls. 4 032843-01 1 | Attraction Plex. with Graphics 15 005378-02 1 | Playfield Piexigias With Graphics te 032842-01 1 | Cardbeard Bezel With Graphics 7 005419-61 1} Speaker, Grill Cover 18 73-7004, 4 | Rivets, 3/16" 0D. x .68 Lg. (.250-.500 Grip.) 1s | a007902-01 1 | cash Box Ass'y. 20 006870-01 | -1_‘| Coin Box Bracket 21 75-55168 3 | Carriage Bolts, 4-20 X 1.00 Lg. (Black) 22 75-045 6 | washers, Split-Lock # 23 75-0188 4 | washers, Plat #4 24 75-9305058 3. | #420 Myton Zockmut | \ 25 75-935 5 | Wing wuts, 4-20 26 75-9155 2 | Hex Nats, 4-20 i 2 72-6808 | 1 | screw, sm. Pan Ha., Phil. #8 Xb" 1g. | 28 72-6812 20. | Screw, Sm. Pan Ha.) Phil. 48 X 3/4" Lg. 29 72-6610 16 | Screw, sm. Pan Hd., Phil. #6 x 5/8" Ig. 30 72-6608 10 | Screw, sm. Pan td., Phil. #6 X45" La, aI 62-1824 | 8 | Wood Screvs, #8 X th" Ug. Fr. Ha. Phil. 32 007103-03 a | on/oee switch cover | 3 006319-03 1 | copyright Deca 34 002728-C1 2. | Rracket, Control Panel 35 46- 201302 2 | Fuses, 3 AMP 36 78-2407 4 | cable rie, Heat stablized 37 | 033016-01 1 | Strain Relief Power Cora ass'y. . 38 | 7e-25001, 1 | Screw Down Tie-Wrap 39 | Av0S90E-01 2 | Rear Door Aszenbly 40 72-8820 4 | screw, sm. Pan #a., Phit, 42 X 1k" 2g.

L sx! L 6 at eeomey = ‘ie

Page 94

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 95

Figure 5-15 Cabinet Assembly (Graphics) Parts List ATARI’

Item Part Number Qty. Description

1A032836-011Cabinet Assembly
2032841-021Side Panel Artwork, Right
3032841-011Side Panel Artwork, Left

KP020 rw] ‘A Warner Communications Company

Page 96

Figure 5-16 Control Panel Assembly (Graphics) A032834-01 D NOTICE TO ALL PERSONS RECEIVING THIS DRAWING.

Reo T=] NODIS wiso YY Wd

4y=2) NOWDaS o-4 ASSV TYNis ON@Nc daentes BG a. Sai GNACES

Page 97

AL ATARI’ Figure 5-16 Control Panel Assembly (Graphics) Parts List

Description

Screws, #10-24 X 7/8" Lg., "F" Type Phil.

ItemPart NumberQty. |
1A032844-011Control Panel W/Graphics
2A000608-02Ll"N" Shift Assembly
3A000598-021Steering Wheel Assy.
4005255-011Shift Bezel
585-22F11410
662-002LLed Switch
7005889-011Shift, Spacer Block
8032846-011Control Panel Support
9A006313-011Harness, Control Panel
10000567-011Bow Washer
1175-5524B2Carriage Bolts, %-20 X 14" Lg.
1275-01581Washer, Flat, ‘"
1375-0452Washer, Split-Lock, %"
1475-91582Hex Nuts, 4-20
1575-04010Washer, Split-Lock, #10
1675-010S10Washer, Flat, #10
17001856-011Bezel, Alum.
1s75-01981 | Washer, Flat

© 4 warner Communications Company KPO20

Page 98

Figure 5-17 Display Assembly (Graphics) [SOLES

A032838-01 D NOTICE TO ALL PERSONS RECEIVING THIS DRAWING tion a CONFIDENTIAL: forbidden without Specitic writ California. ther receipt nor possession thereol cones {ny right in, of license to use, the subject rawing or ‘any design or technical Information snown

ten license, ai ‘granted for the subjéct mater thereo! unless by written agreement With or written permlasion fom the corporation,

i

gi.

SSVI IV OL =~

AT IATS AarI0d G=-TF

Page 99

A ATARI

Part Number

A005374-01 A006917-01 A009063-01 48-001 72-6810 75-0108 72-6610 NYAUBWHH

‘Wainer Communications Company Figure 5-17 Display Assembly (Graphics) Parts List

Description

Display Light Support Assembly Fluorescent Light Assembly (18 inch) Speaker Harness Assembly Speaker, 8" Screws, S.M. Pan Hd. Phil. #8 x 5/8" Lg Washers, Flat, #10 Screws, S.M. Pan. Hd. Phil #6 x 5/8" Lg

KPO20

Page 100

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 101

A

ATARI

Figure 5-18 Fluorescent Lamp Assembly (Graphics) Parts List

Item

OURWNHE Part Number

93-104 70-303 4006916-01 78-2652 78-24001 79-561816 Description

Gibson Fluorescent Fixture 18 inch Fluorescent Tube 18 inch (or Equivalent) Fluorescent Light Harness, 100" Grommet, Rubber Tie Wrap Wire Nut, Ideal 71-B $$$ $$$

Page 102

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 103

TV MONITOR SERVICING

INFORMATION

This chapter provides servicing information taken from the Motorola and TEC service manuals. Each manual has been reprinted by permission of the respective monitor manufacturer.

Your game will include either the Motorola or TEC monitor, depending on their availability during production.

Page 104

M5000-155 M7000-155

MOTOROLA Service Manual

CAUTION No work should be attempted on any exposed monitor. chassis by anyone not Input and output connections for the monitors are made through a 12-pin connector plug located at the rear of the chassis. Inputs consist of composite video, audio, and 115/220 volt AC three-wire. familiar with servicing procedures and precautions. All monitors employ: four stages of video amplification, a two-stage sync separator, a two-stage vertical integrator, a four-stage horizontal sweep circuit, a three-stage vertical sweep circuit, a one-stage spot kill, a one stage blanking amplifier; and a regulated, full-wave bridge power supply.
  • A. GENERAL INFORMATION This manual contains information on the M5000/M7000 monitor series and the +5 volt logic power supply. The M5000 uses a 19-inch CRT and the M7000 uses a 23-inch CRT. All CRTs are of the magnetic deflection type with integral implosion pro- Model Breakdown Chart tection. Model Video Input | 19" CRT 23” CRI| All monitor power supplies are capable of producing both +73 and +12 volts regulated from either IM5000-155 | Composite | x 115-volt or 230-volt AC input to the transformer primary. All monitor variations described herein require IM7000-155 Composite | x a composite video input signal.

SAFETY WARNING

CAUTION No work should be attempted on an exposed monitor chassis by anyone not When handling, safety goggles and heavy gloves should be worn for protection. Discharge picture tube by shorting the anode connection to chassis ground (not cabinet or other mounting parts). When discharging, go from ground to anode or use a well-insulated piece of wire. When servicing familiar with servicing procedures and precautions.

1, Safety procedures should be developed by habit so that technicians rushed with repair work automatically take precautions.

  • A good practice, when working on any unit, is to first ground the chassis and to use only one hand when testing circuitry. This will avoid the possibility of carelessly putting one hand on chassis or ground and the other on an electrical connection which could cause a severe electrical shock.
  • Extreme care should be used in handling the picture tube as rough handling may cause it to implode due to atmospheric pressure (14.7 Ibs. per sq. in.). Do not nick or scratch glass or subject it to any undue pressure in removal or installation. or repairing the monitor, if the cathode ray tube is replaced by a type of tube other than that specified under the Motorola Part Number as original equipment in this Service Manual, then avoid prolonged exposure at close range to unshielded areas of the cathode ray tube. Possible danger of personal injury from unnecessary exposure to X-ray radiation may result.

. An isolation transformer should always be used during the servicing of a unit whose chassis is connected to one side of the power line. Use a transformer of adequate power rating as this protects the serviceman from accidents resulting in Personal injury from electrical shocks. It will also protect the chassis and its components from being

PART NO, 68P25253A47 COPYRIGHT 1977 BY MOTOROLA, INC. () MOTOROLA Data Products _ carovstream, LLinots 60187 PRINTED INU.S.A.

Page 105

damaged by accidental shorts of the circuitry that may be inadvertently introduced during the service operation.

  • Always replace protective devices, such as fishpaper, isolation resistors and capacitors and shields after working on the unit.
  • Before returning a serviced unit, the service technician must thoroughly test the unit to be certain thatit is completely safe to operate without danger of electrical shock. Do not use a line isolation transformer when making this test. a 1000-0 VOLT (OR HIGHER) AC VOLTMETER, NOTES: |, REPEAT EACH CHECK WITH THE LINE CORD REVERSED IN THE POWER OUTLET.
  • METER READING MUST NOT EXCEED 7s VOLTS AC. HOT” LEAD OF METER TO EACH EXPOSED PART OF CABINET, ASWELL AS THE CABINET | GROUND LEAD OF METER TO ANY EARTH

Voltmeter Hook-up for Safety Check In addition to practicing the basic and fundamental electrical safety rules, the following test, which is related to the minimum safety requirements of the Underwriters Laboratories, should be performed by the service technician before any unit whichhas been serviced is installed in a game again.

A 1000-ohm-per-volt AC voltmeter is prepared by shunting it with a 1500-ohm, 10-watt resistor. The safety test is made by contacting one meter probe to any portion of the unit exposed to the operator such as the cabinet trim, hardware, controls, knobs, etc., while the other probe is held in contact with a good “earth” ground such as a cold water pipe.

The AC voltage indicated by the meter must not exceed 7% volts. A reading exceeding 7% volts indicates that a potentially dangerous leakage path exists between the exposed portion of the unit and earth ground. Such a unit represents a potentially serious shock hazard to the operator.

The above test should be repeated with the | power plug reversed, when applicable.

Never reinstall a monitor which does not pass the safety test until the fault has been located and corrected.

Table 6-1 Motorola Monitor Electrical Specifications

MODEL MS5000-155 MODEL M7000-155

PICTURE TUBE 19” measured diagonally (48.2 cm); 184 sq. inch viewing area (1188 sq. cm); 114° deflection angle; integral implosion protection; P4 phosphor 23" measured diagonally (58.4 cm); 282 sq. inch viewing area (1820 sq. cm); 110° deflection angle; integral implosion protection; P4 phosphor standard standard

POWER INPUT 115/230 VAC, 110 Watts (nominal); 60 Hz provision for 230 VAC, 50 Hz

FUSES M5000-155, M7000-155—0.8A

+73 VOLT SUPPLY Electronically regulated over AC inputs from 103 VAC to 130 VAC, or 260 VAC to 260 VAC

VIDEO INPUT 0.5 Volts to 2.5 Volts P/P maximum, composite for 50V at CRT

RESOLUTION 500 lines at picture center

LINEARITY Within 3%, measured with standard FIA ball chart and dot pattern

Page 106

Table 6-1 Motorola Monitor Electrical Specifications

HIGH VOLTAGE 17KV (nominal) = HORIZONTAL BLANKING INTERVAL 11 microseconds typical (includes retrace and delay)

SCANNING FREQUENCY Horizontal: 15,750 Hz+500 Hz; Vertical: 50/60 Hz

ENVIRONMENT Operating temperature: 10°C to 55°C (ambient) Storage Temperature: —40°C to +65°C Operating Altitude: 10,000 ft. maximum (3048 meters) Designed to comply with applicable DHEW rules on X-Radiation CSA certified for use in coin-operated amusements in a combustible enclosure UL listed under specification 1410 (electronic components)

TYPICAL DIMENSIONS (35.8 x 46 x 37.6 cm) 14.11" H, 18.18" W, 14.83” D 16.72” H, 21.56" W, 16.18" D (42.4 x 54.7 x 41 cm)

Specifications subject to change without notice.

B. SERVICE NOTES

Circuit Tracing Component reference numbers are printed on the top and bottom of the three circuit cards to facilitate circuit tracing. In addition, control names are also shown and referenced on the schematic diagram in this manual.

Transistor elements are identified as follows: E—Emitter, B—Base, C—Collector.

Component Removal Removing components ftom an etched circuit card is facilitated by the fact that the circuitry (copper foil) appears on one side of the circuit card only and the component leads are inserted straight through the holes and are not bent or crimped.

It is recommended that a solder extracting gun be used to aid in component removal. An iron with a temperature-controlled heating element would be desirable since it would reduce the possibility of damaging the circuit card foil due to over-heating.

The nozzle of the solder extracting gun is inserted directly over the component lead and when sufficiently heated, the solder is drawn away, leaving the lead free from the copper foil. This method is particularly suitable in removing multi-terminal components. CRT Replacement Use extreme care in handling the CRT, as rough handling may cause it to implode due to high vacuum pressure. Do not nick or scratch glass or subject it to any undue pressure in removal or installation. Use goggles and heavy gloves for protection, In addition, be sure to disconnect the monitor from all external voltage sources.

  • Discharge CRT by shorting 2nd anode to ground; then remove the CRT socket, deflection yoke and 2nd anode lead.
  • Remove CRT from the front of the chassis by loosening and removing four screws, one in each corner of the CRT.

Adjustments A non-metallic tool is recommended when performing the following adjustments.

Regulator Adjustment

NOTE Misadjustment of the +73 volt regulator or the horizontal oscillator may result in damage to the horizontal output transistor or pulse-limiter diode. The following procedure is recommended to insure reliable operation.
Page 107

ene as

  • Connect the monitor to an AC line supply; then adjust supply to 120 volts (240 volts in some applications).
  • Apply test signal to proper input. Signal should be of same amplitude and sync rate as when monitor is in service.
  • Adjust HOR. SET coil L1 until display is stable.
  • Connect a DC digital! voltmeter or equivalent precision voltmeter to the emitter of the regulator output transistor, Q17, or any +73 volt test point.

5, Adjust the 73V ADJUST. control, R93, for an output of +73 volts. Do not rotate the control through its entire range; damage to the monitor may result.

  • When adjustment is complete, the AC line supply can be varied between 103 and 130 volts AC to check for proper regulator operation. With the regulator operating properly, changes in display size should be negligible.

Horizontal Hold/Oscillator Adjustment, Adjust the core of HOR. SET coil L1 until the horizontal blanking lines are vertical or the CRT display is stable (synced).

Vertical Height/Linearity Adjustment

  • Connect a test generator whose output is similar to the display signal normally used.

Figure 6-1 Motorola Monitor Circuit Board in Service Position

  • Rotate the vertical size control, R60, until the smallest display is obtained.
  • Adjust the vertical linearity control, R64, until the top and bottom of the test pattern is equally spaced.

4, Readjust R60 until the desired display height is obtained.

  • Readjust R64, if necessary, as in Step 2 above.

Focus Adjustment The best overall focus of the display is obtained by adjusting the focus control, R42, for best focus at a point which is near the center and approximately 1/3 down from the top of the display.

Monitor Servicing The monitor circuit board may be installed in a service position to provide easier access to the circuit foil when servicing the monitor (see Figure 6-1).

C. THEORY OF OPERATION Power Supply The power supplies are transformer-operated, full-wave, regulated supplies which maintain constant output voltages for input line variations of 103 volts AC to 130 volts AC, or 206 volts AC to 260 volts AC. Regulation of the output voltages is accomplished by using positive feedback through the integrated circuit reference amplifier.

+73 Volt Supply (See Figures 6-3,6-4) When the +73 volt supply attempts to increase, the voltage at pin 3 of IC1 will increase, while the voltage at pin 2 remains constant due to D20. The increasing voltage at pin 3 will cause the output voltage of the reference amplifier (pin 6) to increase the forward bias of Q19. The collector voltage of Q19, forward bias of Q18, and the base current of Q17 will all decrease. The resultant proportional increase of QI17 coliector-to-emitter voltage will cancel the attempted output voltage increase.

When the +73 volt supply bus attempts to decrease; the voltage at pin 3 of IC1 will decrease while the voltage at pin 2 remains constant. The decreasing voltage at pin 3 will cause the reference amplifier output voltage at pin 6 to decrease the forward bias of Q19. The collector voltage of Q19, the forward bias of Q18 and the base current of Q17 will increase. The collector-to-emitter voltage of Q17, which is in series

Page 108

composite oes ewirTER vioe9 WES +) rottowen PREAMP ry vioeo eno | a 4

vioea ota SS ry

Hom non we Sse HOR won won voy use, ort ote volte usin [-—Pregae Lorreny voursac owen | —o+tev eur SUPPLY

}

Figure 6-2 Motorola Monitor Block Diagram

~T nc. oc} i nc. 8<} Palette Pa POWER ! DBA Source} ine i t auCRD R84 150 “Ww "ow QL? ABW REGULATOR

IK | [doo 020

[e3ev bo I usv 2.7K iw ug ele REG, SUFFER

with the output, will decrease proportionally to the attempted decrease in the outbut bus.

Resistor R84 shunts a portion of the output current around Q17 so less power is dissipated within the device. Resistor R82 is the current-limiting resistor for Q18, and R86 controls the leakage current of Q17. Resistors R83 and R85 are the collector load for Q19, and R88 and R87 provide an emitter voltage for Q19 within the range of IC1’s output voltage variations. Capacitor C45 filters high frequency variations from the voltage at pin 7 of 1C1, and C49 is a Miller-effect capacitor which eliminates instability. , PARABOLA NLR _ Fromemitter | OF Q17

EXISTING VERTICAL SAWTOOTH WITHOUT VERT. PARABOLA ; ADDED

PARABOLA PULSE AND VERTICAL SAWTOOTH ADDED TOGETHER, \ HENCE PRODUCING THE REQUIRED VERT, DRIVING SIGNAL,

Figure 6-4 Motorola Monitor Vertical Drive Waveform meen reese

Page 109

+73V. +150V co Ri4 ot g WV ( L

VIDEOolos 8 ris | OR =
ozPREAMP=R17
|aNBKB8K
¢]+5242 | .05aw[ow
05S==
R11==

P/O

pian AstAme[c10

EMITTER —e—

COMPOSITEFe oweRhavBle0.22
VIDED xaea3Rigg0503VIDEO
047P2s |68KaouTPuT
eon]2085.0V

1,

lod63ey|=

C4 22 GND 2 22 1

ae22Kb.

02 :

© Ow.iec4aFas

CONTRAST 7PF A. 10.033 rie: (CATHODE! + Fs OF V1 (oRT) VIA R7B Y a

To Q10 ‘i To Ql BAITTER coutectoR

Figure 6-5 Motorola Monitor Video Amplifiers and Output Circuit

Capacitor C32A filters horizontal frequency variations from the output bus.

Resistor R91 provides bias current for D20, and the value of R99 presents an impedance from pin 2 of IC1 to AC ground (through D20). Capacitor C46 couples high frequency voltage variations, which occur at the output bus, back to pin 3—preventing oscillations for proper operation of the reference amplifier. Resistors R92, R93, and R94 provide voltage division such that the adjustment of R93 can be set equal to the voltage of pin 2 of IC1. Resistor R95 provides bias current for D21 and also provides the +12 volt output. Diode D23 is necessary to temperature-compensate for variations within D21. Capacitor C328 filters AC variations from the output of the full-wave bridge.

Video Amplifiers and Output (See Figure 6-5) The composite video signal is coupled to the emitter-follower Q1 through the input connector P7 and capacitor C1. Transistor Q1 is a buffer stage which matches the impedance of the signal source to the video preamplifer and the sync separator stages. Resistor R1 is a terminating resistor for the video signal source, and resistors R2, R3, R4, and R5 form the biasing network for the stage. Capacitor C2 bypasses higher video frequencies to ground. The composite video signal is coupled from the emitter of Q1 to the sync separator Q10 through C33 and to the contrast control R6 through C47.

The contrast control varies the amplitude and couples the composite video signal to the base of Q2 through capacitor C3. Transistors Q2 and Q3 are complimentary, direct-coupled, common emitter amplifiers. The voltage gain (approximately 12) of the preamplifier stage is controlled by the feedback arrangement of R9, R10, R11, and R12. Resistors R7 and R8 provide the base bias voltage for Q2. Capacitor C48 is used for high-frequency peaking.

The output of the video preamplifier stage is coupled to the video output stage through capacitor C4. Diode D2 clamps the video signal to approximately +0.7 volts (DC restoration) when a sync pulse turns on the sync amplifier Q11. The video output stage is connected in a cascade configuration. Transistor Q4 is a common emitter amplifier and Q5 is connected in a common base arrangement. Capacitors C7, C8, and resistor R16 are used for highfrequency compensation, and resistor R18 controls the gain of the stage to approximately 47. Diode D3 maintains the base of Q5 at +6.2 volts, while capacitor C5 filters the video signal variations from the base voltage. Resistor R13 provides a DC bias path for D2, and R19 and D4 are used to limit the current through the CRT.

Page 110

8 ASF HORIZ ORIVER Q6 A6s HORIZ OSC arg n HORIZ DRIVER 1 x 9 BASE

434 10 wwe 27139 3.3K uaw ™

Figure 6-6 Motorola Monitor Horizontal Deflection Circuit

Capacitor C10 AC-couples the video from the collector of Q5 to the cathode of the CRT if D4 turns off due to high beam currents. Resistor R17 is the collector load for Q5, and R15 provides the bias current for the zener diode D3. Capacitors C9 and C6 filter video frequencies from the +150 volt and +12 volt supplies. Resistor R14 and zener diode D1 are used to supply +12 volts for Q1, Q2, and Q3.

D. HORIZONTAL DEFLECTION CIRCUITS (See Figure 6-6) Phase Detector (See Figure 6-7) The phase detector consists of two diodes (D5 and D6) in a keyed clamp circuit. Two inputs are required to generate the required output, one from the horizontal sync amplifier, Q11, and one from the horizontal output circuit, Q9. The required output must be of the proper polarity and amplitude to correct phase differences between the input horizontal sync pulses and the horizontal time base.

The horizontal output (Q9) collector pulse is integrated into a sawtooth by R24 and C12. During horizontal sync time, diodes D5 and D6 conduct, which shorts C12 to ground. This effectively clamps the sawtooth on C12 to ground at sync time. If the horizontal time base is in phase with the sync (waveform A), the sync pulse will occur when the sawtooth is passing through its AC axis, and the net charge on C12 will be zero (waveform B). If the horizontal time base is lagging the sync, the sawtooth on C12 will be clamped to ground at a point negative from the AC axis. This will result in a positive DC charge on C12 (waveform C). The positive polarity causes the horizontal oscillator to speed up and correct the phase lag. Likewise, if the horizontal time base is leading the sync, the sawtooth on C12 will be clamped at a point positive from its AC axis. This results in a net negative charge on C12 which is the required polarity to slow the horizontal oscillator (waveform D).

Components R23, C15, R25 and C17 comprisé the phase detector filter. The bandpass of this filter is chosen to provide correction of horizontal oscillator phase without ringing or hunting. Capacitor C13 times the phase detector for correct centering of the picture on the raster.

Horizontal Oscillator The horizontal oscillator employs the principles of the Hartley-type oscillator. Its operating frequency is sensitive to its DC base input voltage, thus permitting the frequency of the oscillator to be varied by the output voltage of the phase detector, The main frequency-determining components are 11, C19, and R28. The oscillator operates as a switch being biased alternately into saturation and cut-off. The initial forward starting bias is supplied via R26.

Horizontal Pulse Shaper and Driver The horizontal pulse shaper Q7 serves as a buffer stage between the horizontal oscillator and driver. Capacitor C20 and resistor R30 combine to shape the input waveform to the required duty cycle of 50%, which is necessary to drive the horizontal output stage.

Page 111

REFERENCE HORIZ. SYNC

OSC,ON FREQ NO CORRECTION VOLTAGE DEVELOPED

OSC,SLOWS, POS. CORRECTION VOLTAGE

OSC. FAST, NEG. CORRECTION VOLTAGE

Figure 6-7 Motorola Monitor Horizontal Deflection Waveforms

The horizontal driver Q8 operates as a switch to driving horizontal output transistor Q9 through T1. Because of the low impedance drive and fast switching times, very little power is dissipated in Q8.

Resistor R35 and capacitor C21 provide damping to suppress ringing in the primary of T1 when Q8 goes into cut-off. Resistor R36 is used for limiting currentin the collector of Q8, and C22 filters the horizontal frequency variations from the DC side of the transformer primary.

B Horizontal Output (See Figure 6-8)

The secondary of T1 provides the required low drive impedance for Q9. Resistor R37 limits current in the base of Q9, while capacitor C23 provides additional reverse bias to keep Q9 turned off during the horizontal retrace pulse. Transistor Q9 operates as a switch which once each horizontal time period connects the supply voltage across the parallel combination of the horizontal deflection yoke and the primary of T2. The required sawtooth deflection current through the horizontal yoke is formed by the L-R time constant of the yoke and output transformer primary. The horizontal retrace pulse charges C27 through D8 to provide operating voltage for G2 of the CRT. Momentary transients at the collector of Q9, should they occur, are limited to the voltage on C27, since D8 will conduct if the collector voltage exceeds this value.

The damper diode D7 conducts during the period between retrace and turn-on of Q9 to reduce retrace overshoot; capacitor C28 is the retrace tuning capacitor. Capacitor C25 blocks DC from deflection yoke. Components R38 and C26 are damping components for the width and linearity coils. Capacitor C32D is charged through D10, developing the video output supply voltage.

Lz. = L4A wig oma YOKE WIDTH’ OL o2y

n Qo 7696 1 ona been MORE et +m rornal [ova 03 =. COLLECTOR }

c22

+73V HEATER VOLTAGE! FOR Vi

Dio Fans porssoy| tlesen [20 + crt ‘2nd ANODE

ToC R19; 56K° ov cat

To.cRT PINS

Figure 6-8 Motorola Monitor Horizontal Output Circuit

Page 112

L T0036

Figure 6-9 Motorola Monitor Sync Circuit Syne Circuits (See Figure 6-9)

The video signal is coupled from the emitter of Q1 to the base of Q10 through C33. The negativegoing sync tips turn on Q10 and are clamped to the value of the base voltage due to the base-emitter diode junction. The video information within the composite video signal, however, is less negative and Q10 remains off between each sync tip. Therefore, the waveform at the collector of Q10 will contain only the composite sync pulse information.

Resistors R45 and R46 provide base bias for Q11. The composite sync pulses are amplified and inverted by Q11 where they are coupled to the vertical sync integrator Q12, the horizontal phase detector, and the video clamp diode D2. Resistors R47, R48, and R49, are the collector load for Q11, and also provide base bias for Q12. Resistor R56 limits current through the base-emitter junction of Q12, and R51 is its collector load. Components R52, C34, R53, C35, and R54 forma double integrator which removes the horizontal pulses from the composite sync signal, leaving the vertical pulses to be amplified by Q13 and coupled to the vertical oscillator.

Vertical Oscillator and Output (See Figure 6-10) The vertica! oscillator is a relaxation oscillator and operates at a free-running frequency thatis set by = +12 +73V

VERT. U5 2} CHOKE |

RO6 /

Togs _ COLLECTOR c40 c4l _ fe 10 R68 100} 0.1 gus B2V al VERT. ouTPUT

Figure 6-10 Motorola Monitor Vertical Oscillator Circuit

Page 113

the value of resistors R56 and R57. The series combination of C37 and C38 charges through D14, R61, and R60, until D12 turns on. This occurs when the anode voltage of D12 exceeds the gate voltage by approximately 1.0 volt. When D12 conducts, C37 and C38 are discharged to nearly zero volts; then D12 turns off and the cycle repeats. The value of R61 and thesetting of R60 determines the amplitude of the waveform.

Diode D14 provides a small incremental voltage above ground to overcome the forward base-emitter drop of Q14; D13 provides temperature compersation for the output stage. Resistor R96 provides a constant oscillator load for variations in input impedance of Q14. Transistor Q14 is an emitter-follower used to transform the high impedance drive sawtooth to a low impedance drive for Q15.

The vertical choke L5 acts as a Current source during linear scan time and provides a high-voltage pulse to aid retrace when Q15 shuts off. To limit this pulse to a safe value, a varistor, R66, is connected across the choke.

Since the impedance of the choke decreases when the collector current of Q15 increases, severe vertical non-linearity will result unless some compensation is employed.

Resistors R64 and R62 couple the emitter voltage of Q15 to the junction of C37 and C38. This path is resistive, and the waveform coupled back will be integrated by C38. This results in a pre-distortion of the drive sawtooth. This is done to compensate for the non-linear charging of C37, C38 and the changing impedance of C5. An additional feedback path through R63 and C39 serves to optimize the drive waveshape for best linearity. Capacitor C40 couples the signal to the vertical yoke winding and blocks DC.

Spot Kill (See Figure 6-11) The spot kill circuitry is used to reduce the effect of the electron beam concentrating on one area of the CRT after the monitor is turned off. The circuitry is accomplished by raising the arm of potentiometer R73 to the +150 volt level and, therefore, increasing the brightness to maximum to dissipate the highvoltage charge that normally remains in the CRT.

When the monitor is operating, transistor Q20 is on and its collector is near zero volts. Capacitor C44 charges through the base-emitter junction of Q20 and R97. Resistor R72 provides the base bias voltage required to keep Q20 on. When the monitor is turned R73 BRIGHTNESS

TO R77 CRT, PIN2

Figure 6-11 Motorola Monitor Spot Killer Circuit

off, the falling +73 volts is coupled to the base of Q20 to turn off the transistor causing its collector voltage to rise to approximately +150 volts. Diode D24 Prevents the negative voltage swing at the base of Q20 from exceeding the reverse voltage rating of the transistor.

Blanking Amplifier (see Figure 6-12) The blanking amplifier combines both the vertical and horizontal retrace pulses to turn off the electron beam in the CRT once every horizontal line and once every vertical field. Capacitor C41 couples the vertical retrace pulses and capacitor C31 couples the horizontal retrace pulses to the blanking amplifier. Resistor R68 determines the amplitude of the vertical pulses, while R69 determines the amplitude of the horizontal pulses. Capacitor C42 bypasses R69 to couple the leading and trailing edges of the horizontal retrace pulses to the amplifier. Resistor R70 alfows C41 to discharge when the retrace pulses swing below zero volts. Diode D15 prevents the retrace overshoot from exceeding the reverse voltage rating of Q20. Resistor R71 permits Q20 to turn off between retrace pulses, while R75 and R76 provide the collector voltage for Q20. Capacitor C43 couples the blanking pulses to the control grid of the CRT.

Figure 6-12 Motorola Monitor Blanking Amp Circuit

Page 114

RG / (CONTRAST) 1 u (HORIZ.Osc.) R73. ir (BRIGHT) Rag (Focus) L2

Figure 6-13 Motorola Monitor Chassis Rear View —Component Location

Page 115

FLEA! so em NCAT

Sas

fo wy

an cht LEAD)

To Lan nome TOKE

rocarsins

rote +

” LWCAT LEROY

s310N aioe 88

BOA 14a 4

Figure 6-14 Motorola Monitor Circuit Board Detail—Solder View

Page 116

Figure 6-15 Motorola Monitor Schematic Diagram Alda ¥3m0¢d

Page 117

(NOT

SHOWN) SHOWN)

pg (NOT

R64 —s REO VERT. VERT.

Pi a1 P5 CONTRAST

D23 018 C1

R73

BRIGHT

Figure 6-16 Motorola Monitor Circuit Board Detail—Component Location

Page 118

Table 6-2 Motorola Replacement Part Numbers

PART

NUMBER[DESeRierioNNO.NOAIBERDESCRIPTION |
Capacitors:Gi8S10191B98——.01, 10%, 250V; Poly.
All values ar» in Microfarads unless otherwise noted.C3223S10255B7320/200, 400/125, 600/100,
a123$10255A2747, 50V; Lytic200/50; Lytic
(ov218135660.05, +80-20, Z5V, 50V;C338S10191A51-033, 10%, 160V; Poly.
Cer. Disc.€34,C358S10191A32_—-.047, 10%, 250V; Poly.
C3, C423$187A2622, 25V; LyticC3621S180E60-01, +80-20, Z5V, 50V;
cs215180E60.01, +80-20; Z5V, 50V;Cer. Disc.
Cer. Disc.C37, 38,39 8S10191B670.22, 10%, 250V; Poly.
C6218135660.05, +80-20, Z5V, 50V;c4023S10255A60100, 63V; Lytic
Cer. Disc.ca8S10212B160.1, 20%, 400V; Mtlz.
c7218131625330pf, 10%, X5F, 500V;Poly.
Cer. Disc.can21$180C820.33, 10%, N150, 500V;
C821$180B87220pf, 10%, X5F, 500V;Cer. Disc.
Cer. Disc.C438S10191B670.22, 10%, 250V; Poly.
o)8S10191B99——.015, 10%, 250V; Poly.a423510255B284.7, 100V; Lytic
c1085102128180.22, 10%, 400V;cas8S10191B90—.033, 10%, 250V; Poly.
Mtlz. Poly.C4621813249201, +80-20, Z5V, 100V;
cn218131625330pf, 10%, X5F, 500V;Cer. Disc.
Cer. Disc.C4723S10255B63100, 10V; Lytic
C1221$180C41.0027, 10%, Z5F, 500V;C4821S180D5647pf, 10%, N750, 100V;

Cer. Disc. Cer. Disc.

C1321$180C0210pf, 10%, N150, 500V;4921S180B51-001, 10%, XSF, 500V:

Cer, Disc. Cer. Disc.

c14218180D34~—-..005, 20%, Z5F, IKV;;

Cer. Disc. Diodes:

C1523510229A321.0, 16V; LyticD148510813A03Diode, Silicon, Zener;
c178510191B90——.033, 10%, 250V; Poly.IN5242
cig8510299B28——.01, 10%, 100V; Polycarb. | D248D67120A13Diode; A13
c198510299B29.0082, 10%, 100V;D348S10813A01Diode, Silicon, Zener;

Polycarb. IN5234B

C208S10191B98.01, 10%, 250V; Poly.D448S191A02Rectifier, Silicon; 91A02
(2121S180B51.001, 10%, X5F, 500V;D5,D6= 48D67120A11_—Diode; At
Cer. Disc.D7488134921Diode, Damper; D1D
C228510191898.01, 10%, 250V; Poly.bs485134978Diode, Pulse Lim; D1K
C2323S10255B50150, 10V; LyticD1048S191A05Rectifier, Silicon; 91A05
C2421$180B51.001, 10%, X5F, 500V;pu485137114Rectifier, H.V., D2Y
Cer. Disc.D12485137638Vert. Osc.; MPU6027
C258S10299B270.82, 10%, 200V; Mtlz.D13,D14485191A05Rectifier, Silicon; 91A05
Polycarb.DI1548D67120A11Diode; A11
C26PISIGTG25350 DH th, XSH, BPMsoe Pig’ 485191405Rectifier, Silicon; 91A05
C278S10212A111.0, 10%, 630V; Mtlz.D2048S10813A02Diode, Silicon, Zener;

Poly. 1N5231B

C288S10571A06.01, 5%, 1200V;D2148S10813A03Diode, Silicon, Zener;

Polyprop. Foil 1N5242

C298510212853—-0.47, 10%, 630V; Mtlz.02248D67120A11Diode; A11
Poly.D23,D244819105Rectifier, Silicon; 91A05
Page 119

Table 6-2 Motorola Replacement Part Numbers

e | Part No. Description

Fuses:

F1, F2658138269Fuse, 0.8A-250V

Integrated Circuits:

IC151$10732A01Ref. Ampl.; T3F

Coils/Chokes: u 24C25448A01_ ~— Coil, Horiz. Osc. 12 24D25603A09 ~— Coil, Horiz. Width 13 24D25248A14 — Coil, Horiz. Lin.

1424D25261A09Coil, Defl. (M5000-155,

M5010-155) L4 24D25261A10 — Coil, Defl. (M7000-155, M7010-155) LS 25D25221C12 ~~ Choke, Vertical

Transistors:

Q1488137171Emitter Follower; A6H
Q2488137172Video Pre-Ampl.; A6}
Q3488137127Video Pre-Ampl.; P2S
Q4485134952Video Driver; A2J)
Q5488137476Video Output; BIE
Q6488137172Horiz. Osc.; A6)
Q7488137127Horiz. Pulse Shaper; P2S
Q8485137093Horiz. Driver; A5F
Qo488137570Horiz. Output; B2L
Q10485137173Sync Separator; P2W
Qu485137172Sync Ampl.; A6}
Q12485137172Vert. Sync Integrator; A6)
Q13485137172Vert. Sync Ampl.; A6)
Q14485137639Vert. Driver; MPS A13
Q15485137596Vert. Output; B2V
Q16488137172Blanking Ampl.; A6)
Qi7485137368Regulator; ASW
Q18485134952Reg. Driver; A2)
Q19485137476Reg. Buffer; BIE
Q20485137476Spot Kill; BIE

Resistors/Controls:

NOTE: Only power or special resistors are listed. Use the description when ordering standard values of fixed resistors up to 2 watts. Ro R14 R17 R36 R42 18D25245A27 178135204 17S10731A01 17S10130B07 18D25218A14 Control, Contrast; 500 100, 10%, 5W 3.9K, 5%, 5W. 1.5K, 10%, 3W Control, Focus; 2M om Part No. Description
R6018D25245A29Vert. Size; 250K
R6418D25245A31_—-Vert. Lin.; 100K
R666S$10201A04Varistor, 1 ma, 120V, 0.5
R7318D25245A28Control, Brightness; 200K|
R84178135589150, 10%, TOW
R9318D25245A21Control, +73V out Adj.;

2.5K

R9510731A031.5K, 10%, 5W.

Switches:

swt40S10624A07Switch, Slide; D.P. D.T.

Transformers: 71 25D25221A05 —- Horiz.Driver

T224D25240B23_HV. Transformer
T325D25239B20Transformer, Power

(M5010-155, M7010-155) T3 25D25239B30 = Transformer, Power

Misc. Electrical Parts: v1 96S241A01

v1 96S10848A01

Mechanical Parts: 9B25456A01 42D25158C01 26510251A08 PI 15S10183A69

39S10184A67

P2 15$10183A82

P2 15S10183A81

39510184467

P3 28S10586A35 (M5000-155, M7000-155)

19"—CRT; Type 19VARP4 (M5000/M5010) 23"-CRT; Type M22VATP4 (M7000/ M7010)

Block, Fuse (F1, 2) Clamp, Defl. Coil Heat Sink (Q5) Housing, Connector; Female (12-Contact, Less Contacts) Contact, Plug; 5 Req'd MS5000/M7000, 9 Req'd; M5010/M7010 Housing, Connector; Male (3-Contact, Less Contacts), M5000/M7000 Housing, Connector; Female (3-Contact, Less Contacts), M5010/M7010 Contact, Plug; 3 Req'd for P2 Header, Connector; 2-Contact

Page 120

Table 6-2 Motorola Replacement Part Numbers

REF. PART REF. PART NO. NUMBER DESERIBTION NO. | NUMBER DESCRIPTION

P4, P515810183B12Housing, Connector;14B25459A01Insulator, Fuse Cover

Female (3-Contact, Less (F1, 2)

Contacts) M5010/14A562353Insulator, Mica (Q9,

M7010 Q15, Q17)

39S10184A84Contact, Plug; 3 ea.14C25230A01Insulator, Molded (On

Req'd for P5, M5010/ D11 Body)

M701014810157A30Insulator, Nylon (2-
$215810183A81Housing, Connector;Req'd.); Mtg. P.C. Board
Female (3-Contact, Less14S10550A02Insulator, Transistor

Contacts), M5000/M7000 Cover (Q9, Q15, Q17)

$215810183A82Housing, Connector;35136050Screw, Tpg; 6-20x% CLU

Male (3-Contact, Less Pan (Mtg. Q9, Q15, Q17 Contacts), M50710/M7010 and D11 Socket)

39S10184A64Contact, Receptacle;9D25470A01Socket, CRT; Incl’s.

3 Req'd. for $2 R77, R78, R79, R80

$315810183A94Housing, Connector;9D25201A01Socket, H.V. and CRT

Female (2-Contact, Less Anode

Contacts) 9C63825A03 Socket, Power Transistor

39510184472Contact, Receptacle;Q9, Q15, Q17)

3 Req'd. for $3 41D65987A01 — Spring Special; CRT Aquadag Gnd.

Page 121

A. GENERAL

TM-600 and TM-623 is a television monitor for video games. It is designed for operation either from a power supply of 115 volts/50-60 Hz AC or 230 volts/ 50-60 Hz AC. The complete monitor incorporates a picture tube, an integrated circuit, 20 silicon transistors, 18 silicon diodes, 2 germanium diodes, anda high-voltage selenium diode.

This model is equipped with 5V/3A power supply for the operation of the TTL control board and operation double-pulse-type AFC circuit to obtain a stable picture.

B. SPECIFICATIONS Power Supply Input 115 volts/230 volts 50-69 Hz +10%

Power Consumption 60 watts

Video input 0.5 volts composite P/P for 100 volts 2.5 volts P/P maximum Sync negative at input TEC VIDEOELECTRONICS INC. SERVICE MANUAL

Picture Tube 19” (500 mm), 114° deflection for Mode! TM-690 23” (584.2 mm), 114° deflection for Model TM-623 Integral implosion protection

High Voltage 18 KV nominal at 0 microamperes beam current

Horizontal Retrace Time 12 microseconds maximum

Resolution 500 lines minimum at picture center

Scaning Frequency Horizontal: 15.750 Hz +500 Hz Vertical: 50-60 Hz

Tone Burst Amplifier 5 watts peak output with TTL drive at nominal line, fully adjustable. 4 watts peak output at low line.

Environment Operation: Maximum ambient temperature 50°C (122°F) Storage: Temperature range from —40°C to +65°C

Mode! TM-600 and TM-623 Monitors

TEC Videoelectronics Inc. (TVI} 3610 Scott Boulevard Santa Clara, CA 95050 m1

Page 122

DEFLECTION CENTERING a RINGS HORIZ LIN,

i

Pt CONNECTOR

Figure 6-17 TEC Monitor Chassis, Rear View

soa CONDENSER © SY REGULATOR Goa) py REGULATOR. | con ‘CONDENSER Bs ne

  • iuit

.aa08 VERT. OUT ‘TRANSISTOR

2305 RT. OUT re TRANSISTOR

VERT. LIN.

POWER TRANS. conr, VERT. HEIGHT RESISTOR BRIGHT ‘VERT. HOLD

Figure 6-18 TEC Monitor Chassis, Top View

Page 123

HOAIZ, DRIVER TRANS.

HoRIZ. osc, [— Horiz. ouTPUT con

Hy RECT

HV TRANS

wioT# com,

‘CONTRAST BRIGHT vert HOLD

Figure 6-19 TEC Monitor Printed Circuit Board, Top View

Table 6-3 TEC Monitor Replacement Parts Numbers

Ref. . Ref. -

NoPart No.DescriptionNo,PartNo.Description
Electrical Parts:Q3035300500201MPS9700UVert Amp
PCB12215303600Main PCBDr NAPSBS4
‘A801485TM60003«CRT PCB3044310400030—«-2SC1106_—Vert Output

305 or 2N6307

Transistor and IC:Q4005310500202~~ MPS9700TPhase Inv
Q2005310500202»MPS9700Tst Video Ampor MPS834
or MPS634Q4o15310500202MPS9700T—Horiz Osc
Q2015310500261MPS9750T2nd Video Ampor MPS834
or MPS4356Q40253105004102N6558Horiz Amp
Q2025310500410~=—-2N6558._~—-Video Outputor MJE9742

or MPSU-10 of 2N4354

Q3015310500261MPS9750TSync Separator5310400040—-2SC 1875. Horiz Output

or MPS4356 or MJ205

Q3025310500201© MPS9700U__Vert Osc5310400030=» 2SC1106.-~—-Power Regulator

or MPS834 or MJ3430

Page 124

Table 6-3 TEC Monitor Replacement Parts Numbers

CRT and Diode:

  • veo1 5380000060

D203 5340200280

D204 5340200430

D205 5340200430

D206 5340200430

D207 534020280

D301 5340200260

D401 5340100040

D402 5340100040

D403 5340200300 *D404 5340400120

D801 5340200290

D901 5340200270

D902 5340200270

D903 5340200270

D904 5340200270

D906 5340300220 or 5340300310

D907" D908 0909 D910. 5340200690

Coils and Trans: *1401 589515015

1402 589512015

1403 589512012

1404 5589512012

L405 589514013

1406 589514016 500SB4 CRT

MR9712 Silicon Diode

or IN4004 L. V. Rectifier 1N4148, Silicon Diode or IN4002 Blanking Clip 1N4148 Silicon Diode or IN4002 Blanking Clip 1N4148 Silicon Diode or IN4002 Blanking Clip MR9712 200V Rect or 1N4004

MR-9701 Rectifier Silicon

Diode

AA143 Phase Det

AA143 Phase Det

MR9722 Damper TV20-2K80) H.V. Rectifier or HS30/lb MR9713 400V Rectifier MR9704 or IN4005

MR9704 or IN4005 Silicon Diode MR9704 Rectifier or IN4005 Silicon Diode MR9704 Rectifier or IN4005 Silicon Diode

IN5858A Zener Diode IN6002A

MDA970-1__ Rectifier

TDY1005 D.Y. Coil

HCH1005 Horiz Choke Coil

HC2-035 Choke Coil

HC2-035, Choke Coil AZ-9177DM_ Width Coil LH-15)54 Lin Coil Description Ref. .

No,PartNo.DescriptionRetPart No.

Q902 5310500410 2N6558. Regulator Amp.

or 5310500070MPS-U04Ta01589514015
903 5310500280LM1796-—_—Reference Amp40g589518012
or MPS-D01* 7403589517017
Q904 5310500450MJ2955SV Regulator* 7901589519021

Resistors R201 RD-4L471 R202 RD-4L223} R203 RD-4L563) R204 RD-4L471J R205 RD-41332) R206 RD-21823) R207 RD-41560) R208 RD-4L102) R210 RS-029562) R215 RD-42101)

  • R216 RD-4L101)
  • R217 RD-4L470)

R218 RD-41223)

R219 RD-4L563) R220 RD-4L102) R221 RD-4L102)

R222 RD-2L.102) R223 RD-2L102) R224 RD-2L122)

  • R226 RSO1P101) R227 RD-2L123] R228 RD-2L105) R229 RD-4M681) R302 RD-4M331)

R303 RD-4L562) R304 RD-4M102) R308 RD-4M104)

R309 = RD-4M155T R310 RD-4M332J R311 RD-4M563) R312 RD-4L182) R313 RD-4L153) R314 RD-4L183) R315 RD-41.203) R316 RS-2P333) R327 RD-41104) R320 RD-4L124J TLN-506BX — Horiz Osc TLN-519 Horiz Drive

TFB-1006AS F.

TPW-600 Power Trans

470 ohmJ %W 22K ohm J] % W 56K ohm J %W 470. ohmJ %4 W 33 KohmJ %W 82K ohm J %2W 56 ohm J %W 1K ohm) %W 5.6 K ohm J 2W 1K ohm J %W 100 ohm) %W

47, ohm] %W 22Kohm J %W 56 K ohm J % W 1K ohm) %W 1KohmJ %W 1Kohm) %W 1Kohm] %W 1.2K ohm] %W 100 ohm) 1W 12K ohm | 1% W 1.5 K ohm J %W

680 ohm) %W 330 ohmJ % W 5.6K ohm J % W 1Kohm) %W 100 Kohm J % W

1.5Mohm) % W 3.3 Kohm J % W 56 Kohm J % W

1.8K ohmJ %W 15K ohm) % W 18 K ohm J % W 20K ohm J % W

33 Kohm) % W 100 Kohm J % W 120K ohm J % W

Page 125

Table 6- 3 TEC Monitor Replacement Parts Numbers

Ref. No. Part No.

R322. RD-4L224) R323. RD-4L433) R324 RD-41471) R326 =RD-4L152) R339 RD-4L101) R331 RD-4M331)

R332 RD-4L102)

R333 RSO1P682) R334 RD-21183) R336 = RD-4L221j R337 5160122901

R338 RS-2P150)

R339 5760112901

R340 =RS01P220T

R401 RD-4L153) R402 RD-4L821)

R403 RD-4M561) R404 RD-4M103)

R405 RD-4M103) R406 = RD-41272) R497 RD-4L681) R408 RSO2P682)

R419 RD-4L270) R410 RD-4L182)

R411 RD-4L151)

R412 RD-4L561) R413 RSO1P582) R414 RD-21221)

R415 5160122903

R416 RD-2L569) R417 RS02P182)

R478 RSO1P123) R420 RX05P220) *R421—- RD-2L569)

R422 RD-4L153) R425 RD-4L153) R426 = 55337153 R802 RD-2L154) R804 RD-21474)

R611 RD-2L561) *R901 — RX20P251J R902. RD-2L101)

R903. RD-2L123) Description

220 K ohm J 43 K ohm}

470 ohm) 1.5 K ohm J

100 ohm) 330 ohm J 1K ohmJ

6.8 K ohm J

18 K ohm J

220 ohm)

2.2 ohm) 15 ohm) 1.2 ohmj

  • ohmJ

15 K ohm J 820 ohm)

560 ohm)

10 K ohm J

10 K ohm J 2.7 K ohm J 680 ohm} 4.7K ohm J

  • ohm§J 1.8 K ohm J

150 ohm)

560 ohmJ 6.8 K ohm J 220. ohmJ 2.2 ohm J 5.6 ohmJ 1.8 K ohm J 12K ohm J 22 ohmJ 5.6 ohm J 47° ohm) 15 K ohm J 15 Kohm J 150 K ohm J 470 Kohm J

2MQ}

250 ohmJ 1K ohm J

12 K ohm J %W Ye W % W

ww

ww

YW vw W 1W Ya W Ye W ”W

hw

*%W

1W Ye W Ys W % W Ye W Ya W Ya W Ye W WwW te W YW Ya W Va W 1W

% W

TW v2 W 2W

1W

5W

%W

1W Ye W ve W va W 2 WwW

ve W 20 W *%W v2 W Ref. No.

R904

R905

R906

R907

R909 Part No.

RD-21123) RD-2L223)

RD-21563) RD-21563) RD-21.682)

Controls: R211

R319

R321

R327

R335

R427

R803

R805,

R908 553102005E

553104005B

553124008B

553472008B

553102007B

553303005B

553254005B

553205005B

553472007B

Capacitors: C201

C202

C203

C204

C205

C206

C207

C208

C209

C270

can

C213

C220

C304

C305

C306

C307

C308 CE2G1C470

Ce2G1F101

CE2G1C220

CE2G1H101

CE2G1C220

CI1SLIHS61K

CE2G0)221

5270322401

CE2G2F229

CE2G1H220

CE2G1H339

CK1F2H102K

CE2G2F220

CQIM1H473k

CK1B1H391K

CE2G1H478

56405333

CQIM1H562Kk CQIM1H273K CQIMIH123k

CQIM1H124k

CQIM1H392Kk D$5D1C229M

CQIM1H474} CQ1M1H333K CF2G1A470 Description

12K ohm J 22 Kohm J 56 K ohm J 56 K ohm J 6.8 K ohm J

1K ohm

100 K ohm 220 K ohm 4.7 K ohm

1K ohm

30 K ohm 250 K ohm 2 Mohm

4.7 K ohm

47 mF

100 mF

22 mF

100 mF

22 mF

560 pF K 220 mF

0.22 mF M

2.2 mF

2 mF

3.3 mF

0.001 mF

2.2 mF 0.047 mF K 470 pF K 0.47 mF

0.033 mF K 0.0056 mF K 0.027 mF K

0.012 mF K

0.12 mF K

0.9039 mF K

2.2 mE

0.47 mF

0.033 mF K

47 mE *%W

% W ve W vs W ve W

Contrast

Vert. Hold

Vert. Height Vert. Linearity Vert. Balance

Horiz Hold

Bright Focus

B+ADJ

16V

25V

16V

35V

16V

50V

6.3V

400V

315V

35V

50V

500V

250V

50V

50V

50V

50V

50V

50V

50V

50V

50V

16V

50V

50V

10V

Page 126

Table 6-3 TEC Monitor Replacement Parts Numbers

[ ih Part No. Description Ref. Part No. Description

C317CE2G2A101«100 mF_—sT00VFuses:
318CKIEZH103K0.01 mF_—500V*F9026990620011-250V. 2 Amp.
C3195270310301«0.01 mF_—«630V*F9035990610013-250V. 0.5 Amp.
C401=CQIM1H103K0.01 mMFK = 50V.F904599063001030V 5 Amp.
C402.CQIMIH103K0.01 mF K—50V
403. = CQIM1H393K0.039 mFK_50Vitechanical Parts:
C404CK1B2H151150 mF500VKOO1 = 22-463020Mate-N-Lock Connector (AMP)

60085005 Edge Collector (Molex)

C405CE2G1H3393.3 mF50VS-A3915,Transistor Sacket (SMK)
C406CQIMIH1M4K0.1 mFKSOV*TMe0085001Fuse Holder
C407CQIM1H223K0.022 mF_ J SOVor “TM60085001Fuse Holder
C408=CQIM1IH683K = 0.068 mF J50 VKO05—1-380826-0Stand-Off Fastener (AMP)
409CE2G1F47047 mF25VPag1—PE19-15694P Plug Assy. (Yoke Line)
C410CKIB2H681K680 pF KK500VP42PE19-15704F Recep Assy (Yoke Line)
C411CK1B2H222K—_0,0022 mF K 500VP403PE19-15713P Connector Assy. (Video
C412CKIBIH152K0.0015 mF K 50VInput)
C413CKIBIH102K0.001 mF K 50A621PEI9-15724P Connector Assy.
*C414CKIBSD471K470 pFK—.2KV(Q901 Line)
C415CQIM2AI04K0.1 mFK100¥A631PE19-15736P Connector Assy.
“cate:5270333201OSSTRY406PE19-1574wren 59. net Line)
C417CE2G2C10010 mF160V
C41852703334010.33 mE K200vP407-—-PE19-15752P Recep Assy. (Heater Line}

TE9O1 PE19-1576 Terminator, 6 Pin

Cae56835100Momrav£001135431015Ground Plate
C42056625471470mF = -25VFoor22-164001Frame
C80152703563020.056 mF K 630V0035432001-1Plate Heat Sink A
*C9015240700400450 mF = 200Q403D 54320011Plate Heat Sink C
C902100 mF160. V
C90426202292.2 mF160V
905CKIF2ZH102K0.001 mF_—500V
C9115662510510000 mF-25V
C912566160181 mF16V
NOTE

Laid Gaps: 1, Design and specifications are subject to change

a) 599030001EGP-H751Awithout notice:
  • J—Indicates + 5% tolerance

7803 K—Indicates =10% tolerance

switches: M-—Indicates =20% tolerance

*SW-1PE13-1567115V/230V Power Line

Slide Switch

Page 127

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 128
WARNING Safety-Critical Components Components marked with an asterisk (*) on the parts list and with gray shading in the schematic have special characteristics important for safety. You may create shock, fire, or other hazards by using a replacement that does not have the same characteristics as the recommended part.

280:-0904 MRE7Oa

erg Pl 10 PLT

Tat iw-e23} TPW-600

TR, IC, and Connector Lines

te NES UIO_LMI786 MPS 9417 INSE5DA Woe wes a7s0Mes 9700 1NEOD2A NES U08 wes o7soMeS 9700 1N6 poe eed coone| o ‘msEsa0 ro we reosce = mEo7a2

1 Pe ram

OF o8

Msz985 2sci 106 asc 1978 Mes 97807

=

Pas pee

Page 129
  • Unless otherwise specified, all resistance values are in ohms.
  • Unless otherwise specified, in the schematic diagram all capacitor values less than 1 are expressed in mfd, and values more than 1 are in pfd.
  • Voltage readings are taken with VTVM from point indicated on chassis to ground. NOTES
  • All waveforms are measured with strong signal input and contrast set to give normal picture.
  • This schematic diagram covers basic or representative chassis only. There may be some differences between actual components on chassis and the schematic diagram.

101 CONTRAST J tu

aa wes 87507

Figure 6-20 TEC Monitor Schematic Diagram

Page 130

CRT P.C.B.

Page 131

BOTTOM VIEW

Figure 6-21 TEC Monitor Wiring Diagram

Page 132

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 133

TM-095, 1st Printing

YOUR COMMENTS, PLEASE!

Your comments will assist Atari in improving the usefulness of our publications. They are an important part of preparing for revisions of manuals and parts catalogs. No postage stamp is necessary if mailed in the U.S.A. If you have any technical questions about certain Atari or Kee Games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply:

Name Firm C Distributor 0 Operator

Address OD Other

City State _ Zip

Page 134

euy siya Buoye IND. Tape This Edge

Atari, Inc. P.O. Box 9027 Sunnyvale, CA 94086

le Plog pues LL

Buyeauibug do-ulog ‘dnoiy suonesqng -uny

980r6 EWIOHIED ‘ejeaKuuNg 1206 X08 “O'd “2u| ‘ue

vO ‘aleakuung POOL# NWUWWed SSPID ISil4

plod S41}

Page 135

WARRANTY

Seller warrants that its printed circuit boards and parts thereon are free from defects in material and workmanship under normal use and seryice for a period of ninety (90) days from date of shipment. Seller warrants that its television monitors (in games

supplied with monitors) are free from defects in material and workmanship under

normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted.

If the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer’s account for such

products which are returned to Seller during said warranty period, provided:

(a) Seller is promptly notified in writing upon discovery by Buyer that said products are defective; ; ‘

(b) Such products are returned prepaid to Sellers’ plant; and

  • Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing.

In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages.

EXCEPT FOR ANY EXPRESS WARRANTY SET FORTH IN A WRITTEN CONTRACT BE- TWEEN SELLER AND BUYER WHICH CONTRACT SUPERSEDES THE TERMS OF THIS ORDER, THIS WARRANTY IS EXPRESSED IN LIEU OF ALL OTHER WARRANTIES EX- PRESSED OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTA- . BILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND OF ALL OTHER OBLIGA- TIONS OR LIABILITIES ON THE SELLER'S PART, AND IT NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR THE SELLER ANY OTHER LIABILITIES IN CONNECTION WITH THE SALE OF PRODUCTS UNDER THIS OR- DER.

This document is and contains confidential trade secret information of Atari, Inc.

This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed | to any person for any other purpose whatever, and remains the property of Atari, Inc.

Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc. :

Page 136

> = oO Cc a ES < o ee BS xX > ne om ot =e) Le mal i [e) 2D we n> Eg QS Oo a (oD) on 7 WD © oe: 109) > Bo OL She mi = lon m ATARI INC ‘ x > ‘ Pi ‘ > owned subsidiary of Atari, Inc. a wholly

KEE GAMES

RD