Warlords Cocktail TM-177 1st Printing
Warlords (Atari, 1980) · Technical Manual · 52 pages · 37 sections · original scan
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
GAME SERIAL NUMBER LOCATION Your game’s serial number is stamped on a plate on the outside of the game. The same number is also stamped on the chassis of the monitor, RegulatoriAudio Il PCB, and the Warlords™ Game PCB. Please mention this number whenever calling your distributor for service.
WARLORDS™ GAME PCB
REGULATOR/AUDIO Il PCB
GAME SERIAL # IDENTIFICATION TAG
Operation, Maintenance and Service Manual
Complete with Illustrated Parts Lists A ATARI o-
Warlords ™/Cocktail
Copyright © 1981 by Atari, Inc. All rights reserved.
No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher.
Published by: ATARI, INC. 1265 Borregas Avenue P.O. Box 427 Sunnyvale, California 94086
Lithographed in the U.S.A. 4k
Warlords ™/Cocktail
Notice Regarding Non-Atari Parts
WARNING
Use of non-Atari parts or modifications of your Atari game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.
Atari, Inc.’s warranty (printed on the inside back cover of this manual) may be voided, if you do any of the following:
1.) you substitute non-Atari parts in your coin-operated game, or
2.) you modify or alter any circuits in your Atari game by using kits or parts not supplied by Atari.
Not only may the use of any non-Atari parts void your warranty, but any such alteration may also adversely affect the safety of your game, and may cause injury to you and your players.
Warlords Cocktail
Table of Contents
1 Location Setup A. New Features. .... 0.0.6. ccc cence teens 1 B. Opening the Game Cabinet . a 3
- Opening the Table Top ....... 0.2.0... c cece eee eee ee 3
- AcceSS Panel. ..... 6... een neces 3
- Closing the Table Top. 3 C. Gamelnspection.... 3 D. Game Installation. . 4
- Voltage Selection .... 0... cee cee eee 4
- Interlock and Power On/Off Switches 1 4 E. Adjusting the Table Legs............. - 6 F. Self-Test Procedure ...........0.0 50.0020 se eee wi. 7 G. Option Switch Settings. 13
- Bonus Play Feature . 13
- Coin Mechanism Multipliers . . . 13
- Examples of Game Price Settings 13 H. GamePlay .. 13
- Attract Mode... 13
- Ready-to-Play Mode 13
- PlayMode........... . wee 14
- High Score Initial Mode ........ 0... cece eee eee eee eee 14
2 Maintenance and Repair A. Cleaning 0.0... cece cece etter eee ett ttt e nae 16 B. Fuse Replacement.... . 16 C. Opening the Control Panel .... .. 16
- LED Switch Replacement... .. -. 16
- Potentiometer Replacement -- 16 D. Monitor Removal ........... . 18 E. Printed-Circuit Board Removal .19
- Game PCB Removal........ 19
- Regulator/Audio II PCB Removal 19 F. Speaker Replacement......... . 20 G. Game Operation. ...... 0... eee eee eens 21
3 Illustrated Parts Lists Illustrations and parts lists begin on page .......... 0... eee eee eee 26
Warlords ™/Cocktail
List of Illustrations
Figure 1 Overview of Game ........... 0c cece eee ee eee eens 2 Figure 2 Installation Requirements . 4 Figure 3 Voltage Plug Selection. .... . 4 Figure 4 Interlock and Power On/Off Switches .... 2.0... 20000 c eee eee 5
Figure 5 Adjusting the Table Legs .... 2.0... 0. e ccc cee cece ee 6 Figure 6 Location of Self-Test Switch, Volume Control and Option Switches... 7 Figure 7 Self-Test Procedure 8 Figure 8 Game Option Settings ..... 0.66... cece cece cece eee ee 9
Figure 9 Game Price Settings .... 2... 6... ieee ccc ee 10 Figure 10 Coin Counter Option Settings ..... 0.0.6... cece cece eee ences 12 Figure 11. Replacing Player Controls .. 7 Figure 12 MonitorRemoval .......... 0-2... c eben een teens 18
Figure 13 Printed-Circuit Board Removal ........... 0... c ce en neces 19 Figure 14 Speaker Replacement Figure 15 Power Distribution .. . . Figure 16 Signal Distribution ............ 0... c eee eee
Illustrated Parts Lists: Figure 17 Cabinet-Mounted Assemblies Figure 18 Regulator/Audio II PCB Assembly ..............0000 0 cece eee ee 30 Figure 19 Warlords™ Game PCB Assembly ........... 060-00 e cece nee e eee 32 Figure 20 Control-Panel Assembly. .... 0.0... 0.00 e cece eee een tenet ee 35
Figure 21. Power Supply Assembly for Color Raster-Scan Games Figure 22. Double Coin Acceptor/Mount Assembly .............00 0000 eee
Warlords™/Cocktail
vi
WEST and CENTRAL U.S.A. Parts for all Atari customers in the U.S.A. Game sales and service
Atari, Inc. California Customer Service Office 1105 N. Fair Oaks Avenue P.O. Box 427, Sunnyvaie, CA 94086 Telex 17-1103 (Monday-Friday, 7:30-4:00 pm Pacific Time) Zs From California, Alaska or Hawaii (408) 745-2900 = From anywhere else in this area toll-free (800) 538-1611
EAST U.S.A. Game sales and service only
Atari, Inc. New Jersey Customer Service Office Cottontail Lane, Somerset, NJ 08873 Telex 37-9347 (Monday-Friday, 7:30-4:00 pm Eastern time) exe From New Jersey (201) 469-5993 ae From anywhere else in this area toll-free (800) 526-3849
EUROPE Parts for all Atari customers in Western Europe. Game sales and service
Atari Ireland Limited European Customer Service Office TIPPERARY TOWN, Tipperary Town, Ireland IRELAND Telex 28165 (Monday-Friday, 9:00-6:00 pm GMT)
@ 06252155
ae
Location Setup
A. New Features
The Warlords™/Cocktail game has three new parts. Even if you are familiar with Atari games, you should note these important differences. The new parts are: @ New-Style Cocktail-Table Cabinet. This cabinet design eliminates the side door and provides a new location for the game printed-circuit boards (PCBs). The table top is end-hinged for easy access to the PCBs and control panels. The coin box is accessible only from the outside of the cabinet. @ 14-Inch Color Monitor. Made to Atari specifications by either Matsushita or Sanyo, it has high reliability, a compact size, and should maintain its color convergence for a long period of time. @ Adjustable Table Legs. These newly-designed table legs provide improved cabinet stability while allowing two cocktail-table height settings: 27 7/8 and 30 inches. A third “upright” setting is 39% inches high, and allows the game to be placed in locations with other upright games. These new parts, as well as all other major parts in the game, are illustrated in Figure 1. Throughout this manual, wherever one of these new parts is
Warlords ™iCocktail
COLOR MONITOR
| _-—— TABLE TOP
UTILITY COIN SWITCH, GAME PCB: SELF-TEST SWITCH, AND VOLUME CONTROL
REGULATOR! AUDIO Il PCB CONTROL PANEL
‘SPEAKER
COIN ACCEPTORS
\ ADJUSTABLE LEG
COIN COUNTER
Figure 1 Overview of Game
B. Opening the © Game Cabinet
. Opening the Table Top To open the game cabinet unlock and open the two locks at one end of the game, located immediately below the table top (see Figure 1). @ Carefully lift the table top until the support arm locks into place. Do not jam the table top at the end of its upward swing. =
- Access Panel To open the access panel, lift up the U-shaped steel security bar inside the cabinet wall. @ The access panel near the bottom of the cabinet will then come out. This small panel was designed with a bar instead of the usual lock to reduce the number of keys required for this game.
- Closing the Table Top @ To close the cabinet, stand on the coin acceptor side of the cabinet and grasp the table top with your right hand. @ With your left hand, press the button at the middle of the support arm and pull the support arm toward the left. @ Gently lower the table top to the closed position. @ Be sure the control panel is properly engaged with the table top. Otherwise you might damage either the top or the control panel. Do not forcefit the table top in order to lock it. @ Lock the two latches on the left end of the cabinet, located just underneath the table top. Warlords™/Cocktail
Cc. Game Inspection
This new game is ready to play upon removal from the shipping carton. However, your careful inspection is needed to supply the final touch of quality control. Please follow these steps to help us insure that your new game was delivered to you in good condition.
[__vonotat NOTE rene _| Do not plug the game in yet!
- Examine the exterior of the game cabinet for dents, chips, or broken parts.
- Unlock and open the access panel of the cabinet and inspect the interior of the game as follows: @ Check that all plug-in connectors (on the game harness) are firmly seated. Replug any connectors found unplugged. Don’t force connectors together. The connectors are keyed so they only go on in the proper orientation. A reversed edge connector will damage a PCB and will void your warranty. @ Check that all plug-in integrated circuits on the game PCB are firmly seated in their sockets.
@ Note the location of the game’s serial number—it is printed on the special label on the outside of the game cabinet. Verify that the serial numbers also stamped on the Warlords™ Game PCB, Regulator/Audio II PCB, and monitor are all identical. A drawing of the serial-numbered components is on the inside front cover of this manual. Please mention this number whenever you call your distributor for service. @ Check all major subassemblies such as the Power supply, control panels, and monitor for secure mounting.
Warlords Cocktail
D. Game Installation
°
Figure 2 Installation Requirements
Power 100 watts Temperature Q to 38° C (32 to 100°F) Humidity Not over 95% relative Space Required 63% x 84 cm (25 x 33 in.) Game Height 65 to 101 cm (25% to 39% in.)
- Voltage Selection The power supply in this game has four colored voltage selection piugs and operates on the line voltage of almost any country in the world.
Before plugging in your game, check your power supply to be sure the voltage selection plug is correct for your location’s line voltage. Check the wire color on the plug and see if it is correct per Figure 3.
VOLTAGE $ SELECTION PLUGS
Fuse cover must be in place during gare operation.
- Interlock and Power On/Off Switches To minimize the hazard of electrical shock while working on the inside of the game cabinet, an interlock switch has been installed under the table top (see Figure 4). This switch removes all AC line power from the game circuitry when the table top is opened. Check for proper operation of the interlock switches by doing the following: @ Make sure the table top is closed. Plug the AC line power cord into an AC outlet. @ Set the power on/off switch to the on position. Within approximately 30 seconds the monitor should display a picture. @ Slowly open the table top. The monitor picture should disappear when the top is lifted approximately 2¥2 cm (1 inch). @ If the results of the preceding step are satisfactory, the interlock switch is operating properly. If the monitor doesn’t go off as described, check to see if the interlock switch is broken from its mounting or stuck in the on position.
Line Voltage Range Plug Color 90-110 VAC (100) Violet 105-135 VAC (120) Yellow 200-240 VAC (225) Blue 220-260 VAC (240) Brown
Figure 3 Voltage Plug Selection
SAFETY INTERLOCK' SWITCH
SWITCH COVER
SWITCH COVER
ON/OFF SWITCH Reach under game to activate switch
Figure 4 Interlock and Power On/Off Switches Warlords™/Cocktail
Warlords™/Cocktail
@ Remove or empty the coin box. Loose coins may slide out of the coin box and into the game cabinet. ®@ Lay the tabie on its side. Place a support (the coin box, books or tool box) under the recessed side of the cabinet. @ Loosen the two Allen-head screws on each leg. Grasp the legs and slide them into the desired position. Then tighten the screws.
REMOVE COIN BOX
USE TWO SCREWS WHEN ATTACHING EACH TABLE LEG!
27 718 in.
‘SHIPPING POSITION (2534 in.)
Figure 5 Adjusting the Table Legs
E. Adjusting the Table Legs
This cocktail-table game is designed for four adjustable heights—65, 70, 76 or 101 cm (25%, 27 7/8, 30 or 39% inches). To adjust the table height, refer to Figure 5.
F. Self-Test Procedure
This game will test itself and provide data to demonstrate that the game's circuitry and controls are operating properly. The data is provided on the monitor and the game speaker; no additional equipment is necessary. Warlords ™/Cocktail
Part of the self-test procedure includes a display of the operator-selectable game options. Therefore, we suggest you run the self-test procedure anytime you need to change the game’s options.
To run the self-test, follow the instructions outlined in Figure 7.
WARLORDS™ GAME PCB. OPTION SWITCH (ONE OF THREE SETS)
COIN SWITCH (FOR OPERATOR CONVENIENCE) VOLUME CONTROL VOLUME INCREASE: TURN CLOCKWISE SELF-TEST SWITCH
We
FOR EASIEST ACCESS TO BOTH 8-TOGGLE OPTION SWITCHES, REMOVE THE ACCESS PANEL ON SIDE OF GAME.
Figure 6 Location of Self-Test Switch,
Volume Control and Option Switches
Warlords™/Cocktail
Instruction Figure 7
Results if Test Passes Self-Test Procedure
Results if Test Fails
- Unlock and open the table top. Set self-test switch to on position (see Figure 6).
- Turn each shield control knob slowly back and forth and observe the monitor.
- Activate the following switches, if you can reach them: slam, utility coin, two coin mechanism, and four LED switches.
- When satisfied with test, set selftest switch to off position. Close and lock the table top. The monitor displays the picture below. You may hear RAM FAILURE is indicated by the message BAD RAM. a ticking sound. This is normal. ROMIPROM FAILURE is indicated by the message BAD ROM.
or Seceaatade tens ine
A fireball will move smoothly on a diagonal across the A fireball will jump erratically or not move at all, inscreen. Ignore any “wraparound” that the fireball does dicating a bad potentiometer or loose harness wires. on the screen.
You will hear a high tone; also, one of the characters in __A tone produced while you are not pressing any switchthe 4th row of Os and 1s on the screen will change toa _es indicates a shorted switch. 1 (on). Simultaneously pressing more and more switches will progressively lower the tone. Tone disappears No sound at all indicates bad sound circuitry, loose when switch is released. speaker wires, bad switch circuitry or volume control turned all the way down.
All coin acceptor and LED lamps are lit. Either some or all lamps are dark (burned out).
SWITCH TOGGLE 8 oeee OD gore OD Chee XX 1 al
/ — UTILITY COIN SWITCH
L&RCOIN SWITCHES Bore 00 Bb TOGGLE 1 AR
‘SWITCH AT J2
SWITCH AT M2 o20rF eian| Ignore this row
4 POWER-STONE SWITCHES
SLAM SWITCH
Warlords™/Cocktail
Figure 8 Game Option Settings To change toggle positions on the switch assemblies, you need not remove the game PCB. The switch, usually colored blue, is easily accessible when the Warlords™ Game PCB is mounted in place. When changing the options, verify proper results on the monitor display by performing the self-test. Note that changing an option on any of the following eight toggles will cause an immediate change on the monitor screen during the self-test.
Toggle Settings of 8-Toggle Switch on Warlords PCB (at J2—LOWER RIGHT switch when PCB is in game)
| 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | Option |
| On | On | English language | $ | |||||
| On | Off | French language | ||||||
| Off | On | Spanish language | ||||||
| Off | Off | German language | ||||||
| 3B | B | B | On | Music ends each game. | $ | |||
| 8 | 3 | g | Off | Music at end of game only for a new high score | ||||
| 3 | S | 3 | (1- and 2-player games only). | |||||
| =z | = | = | ||||||
| On | On | 1- to 4-player game costs 1 credit. | ||||||
| On | Off | 1-player game costs 1 credit; 2- to 4-player game costs |
2 credits. $
| Off | Off | 1- to 4-player game costs 2 credits. |
| Off | On | 1-player 1 credit; 2-player 2 credits; |
Splayer 3 credits; 4-player 4 credits.
$ Manufacturer's suggested settings For pricing for “credits”, see Figure 9.
Warlords™/Cocktail
Figure 9 Game Price Settings The white block below contains Atari's suggested settings. All numbers 1 thru 8 are toggle settings on the 8-toggle switch at location M2, on the Warlords™ game PCB (the LOWER LEFT switch assembly).
50¢ PER CREDIT: Bonus 50 = 1 credit Bonus $.75 = 2 credits No bonus $1.00 = 3 credits $1.00 = 3 credits
all 25¢ Mechs
25¢1$1.00 Mechs
25¢ PER CREDIT:
Bonus Bonus No bonus 8.50 = 3 credits $1.00 = 5 credits ae — : aha
| an | @) | on | on | on | on |
25¢ Mechs
| 4 | 3 | 2 | 1 |
| On | On | Off |
Circled numbers refer to coin-door labels you should use with each situation (labels are illustrated on the following page).
Warlords™/Cocktail
Figure 9 Game Price Settings, continued For your information, we have defined below the switch settings for those options relating to game price, coin mechanism multipliers, and bonus play. This information is useful in case you need to temporarily set the Warlords™ game on free play, or if you have German coin mechanisms in your door.
Toggle Settings of 8-Toggle Switch on Warlords
6 5 4 3 PCB (at MZQ—LOWER LEFT switch when PCB is in game) Option
On
On.
On
Off On
On
Off
Off On On On Off
Off On
Off Off
On Off
On
Off On On Off Off On Off On Off Free play 1 coin® for 2 credits 1 coin* for 1 credit $ 2coins* for 1 credit
Right coin mech x 1 $ Right coin mech x 4 Right coin mech x 5 Right coin mech x 6 Left coinmech x 1 $ Left coin mech x 2 No bonus coins = $ For every 2 coins* inserted, game logic adds 1 more coin*
For every 4 coins* inserted, game logic adds 1 more coin* For every 4 coins* inserted, game logic adds 2 more coins*
For every 5 coins" inserted, game logic adds 1 more coin*
“In the U.S., a coin is defined as 25¢. In Germany a coin is 1 DM.
$ Manufacturer's suggested settings
oe A. @@ 2 coins =1 play ‘ATARI
°e A. @ 1coin = 1 play
AO 6 @ 2 coins = 1 play ATARI
6 eee 4 coins = 3 plays
To receive any bonus “coins” from the game logic (as listed in the last four settings above), players must insert all coins before pressing any start button.
ne @@ 2coins
AA Q@®@ 3 coins 8080 4 coins
e @@ 2 coins =1 play A @ $1 coin =3 plays (Susan B. Anthony coin)
O71 @ 1 coin = 1 play amr’ 2 play minimum (2 coins = 2 plays)
(For operator use—write in the appropriate phrase. Use a permanent-ink water-resistant marker.)
Warlords Cocktail
Figure 10 Coin Counter Option Settings
[These toggles determine which coin mechanisms activate which counters]
Toggle Settings of 4-Toggle Switch on Game PCB (L9) Two coin acceptors Two coin acceptors and a pushbutton utility coin switch in the Three coin acceptors
| 4 | 3 | 2 | 1 | in the coin door: | game: | in the coin door: |
| On | On | Both acceptors activate ali coin | Do not use this setting. | All 3 are same denomination and |
counters simultaneously. they activate all coin counters simultaneously.
| Off | On | Both acceptors activate 2 count- | Do not use this setting. | Left and center acceptor activate |
| BOB | ers separately. | ‘one coin counter, right acceptor ac- | ||
| S$ | $ | tivates another coin counter. |
3 8
| = | = | On | Off | Both acceptors activate all coin | Utility coin switch will not acti- | Left acceptor activates one coin |
| counters simultaneously. | vate a coin counter, if you donot | counter; center and right acceptor |
hook up it up. Both acceptors ac- activate another coin counter. Not tivate all coin counters simulta- for any currently designed 3-mech neously. $ cain door.
| Off | Off | Both acceptors activate 2 count- | Utility coin switch will nat ac- | Left, center and right acceptors ac- |
ers separately. tivate a coin counter, if you do not hook it up. Left and right acceptors activate 2 coin counters ‘separately. tivate 3 coin counters separately.
$ Manutacturer’s suggested setting
G. Option Switch Settings
- Bonus Play Feature Warlords™/Cocktail is one of the first Atari games to offer a bonus play for certain combinations of coins inserted. This bonus feature is operatorselectable, meaning you may choose to offer it or not.
For example, with your game set at 50¢ per credit, players who deposit four successive quarters or a $1.00 coin, then press the start button, will receive a
sn00: credit. Therefore, players receive 3 credits for
1.00.
This bonus feature encourages players to insert more money than just the minimum 50¢ you could require for one credit. Various other bonuses are available (see Figure 9).
- Coin Mechanism Multipliers The Atari coin acceptor mount for this game is available with about a dozen different mechanisms. You may have both mechanisms accept the same or different denominations.
Regardless of the type of mechanism you install, you must correctly set the “multipliers” for each mech on the game PCB. The multipliers determine how much each mechanism will be worth to the game's logic.
The basic unit of measurement is 25¢, which equals a multiplier of x1. Therefore, if you have 25¢/$1 coin acceptors, you will probably want to set the left and right option-switch multipliers at x 1/ x 4.
You can set these multipliers with toggles 3 thru5 on the Warlords™ PCB switch assembly at location M2. For exact settings of these toggles, refer to Figure 9.
- Examples of Game
Price Settings
Figure 9 explains the options, giving twelve examples of the most common U.S. situations. The toggles mentioned are all in the switch at location M2, they only relate to game price, coin mechanism multiptiers, and the bonus credit for multiple quarters or the $1.00 coin. You should set the toggles relating to other functions as you see fit, although Figures 8, 9, and 10 provide “$” signs indicating Atari's recommendations. Warlords™/Cocktail
H. Game Play
Atari’s Warlords™/Cocktail is a one- to four-player game with a color raster-scan monitor. The game depicts a third-person view of four castles. The knights and kings use shields to defend their castle walls from the fireballs that ricochet around the playfield.
Players can capture and catapult the fireballs at opposing castles, using their shield control and “power stone” pushbutton. When a fireball hits a castle wall, it destroys one or more bricks, depending on its speed.
The computer controls any unactivated positions in the game, with black knights displayed in the appropriate castles. These knights catapult fireballs at the players with increasing accuracy, to provide challenge.
The game has five possible modes of operation: attract, ready-to-play, play, high score initial, and self-test. Self-test is a special mode for checking the game switches, potentiometers, and computer functions. You may enter this mode at any time. When entered, all game credits are cancelled.
- Attract Mode The attract mode begins when power is applied to the game, after a play or high score initial mode, or after self-test. This mode is continuous and is only interrupted when a game is paid for and accepted or when you enter self-test.
In this mode, the monitor displays a simulated game. A fireball bounces across the playfield, knocking out several bricks on castle walls. Shields are left invisible to indicate the attract mode. This is why the fireball appears to be deflected from something near the middle of the playfield.
If you select one of the three coined-play settings, the screen shows GAME OVER/INSERT COINS, followed by various messages regarding the number of coins required for multi-player games. If you set the appropriate option switches for free play, the game displays the messages PRESS YOUR POWER STONE and START YOUR KING.
- Ready-to-Play Mode This mode begins when sufficient coins have been accepted for at least a one-player game. It ends when any player presses a start pushbutton and the subsequent countdown has ended. The countdown lasts about 10 seconds (counting from 9 to 0) and allows more players to insert coins and join the first player.
Warlords™/Cocktail
- Play Mode The play mode begins when any start button is pressed and the countdown has ended. The mode ends when the last player's castle (containing a crown) is penetrated by a fireball. At this point a white cloud envelopes the crown, and both disappear.
During the countdown a dragon flys back and forth across the screen with a fireball in its mouth. By the end of the countdown, all positions activated by start buttons have had their black knights changed to kings’ crowns. The unactivated positions remain as knights and are controlled by the computer. The dragon then spits the fireball from its mouth ina random direction towards a player. The objective is to destroy the three other castles, while protecting one’s own castle with the moving shield (potentiometer). The LED pushbuttons have dual functions: in the ready-to-play mode they work as start switches, and during game play they become “power stones” to allow players to capture and catapult fireballs at opponents.
The spinning fireballs released from a shield have more destructive force on a castle wall than a fireball simply deflected from another wall or the sides of the playfield. However, players will soon find out that they cannot hold onto fireballs for long, since they slowly destroy their own castle walls under the fireball.
Additional fireballs appear at predetermined intervals or when a castle is destroyed, whichever comes first. Amaximum of four fireballs simultaneously appears on the screen.
In one- and two-player games, the players’ crowns will be accompanied by a zero, to begin scoring. The point-scoring system is printed on each control panel (the black knights do not earn points). In threeand four-player games, no scores appear: the winner is the survivor of the battle against the other three warlords—be they kings or black knights.
In one- and two-player games, if the black knight has the surviving castle, the game ends. However, if a player (king) has the surviving castle, that player receives bonus points, all castles are rebuilt, and the game continues with a new battle at a higher “level.”
The subsequent levels begin, as mentioned before, with the fireball thrown out by the dragon. In the higher levels black knights play more accurately and faster.
The game provides individual player percentaging based on the skill of the player or players. In sensing that a player is not very skilled, the computer softens the game play for a short period, allowing the player to adjust to the game play. In sensing that a player is more skilled, the game difficulty increases.
If players abuse the game and activate the slam switch, the computer will produce an oscillating high-pitched sound as a warning signal. However, game play will not be interrupted.
- High Score Initial Mode If one or more players have achieved the highest score currently in the memory, they can enter their initials. Turning the shield-control knob will change the letters, and pressing the start button will enter the selected initial. Up to three letters will be displayed next to the individual or team high score during the attract mode.
All games require certain maintenance to keep them in good working order. Clean, properly maintained games will attract players and earn more profits.
The most important maintenance item is running the self-test every time you collect money from the cash box. Just looking at a game will not tell you if potentiometers or light-emitting-diode (LED) switches are broken, or if LEDs have burned out. The selftest will inform you of any of these possible problems.
Second, you should regularly clean the outside of dq a CVG the game and the coin mechanisms. f,
>
Maintenance and Kepair
Warlords ™/Cocktail
A. Cleaning
The exterior of the game cabinet and the metal and glass surfaces may be cleaned with any nonabrasive household cleaner. If desired, special coin machine cleaners that leave no residue can be obtained from your distributor.
The large monitor shield is made of tempered glass and should be scratch-resistant: if cleaned without abrasive substances, you should hardly ever have to replace it.
B. Fuse Replacement
This game contains six fuses—all on the power supply assembly (not including the monitor fuses). Replace fuses only with the same type as listed in Figure 21 of this manual. See the Matsushita or Sanyo color-monitor manual for the monitor fuse data.
C. Opening the Control! Panel
Prior to repairing or replacing any component on either control panel, first unplug the game. Next, open the game top as described in Chapter 1, Section B, Opening the Game Cabinet. Then simply tilt the top edge of the control panel towards you.
- LED Switch Replacement The light-emitting diode (LED) switches on the control panel have a very low failure rate. In case a switch should ever be suspect, first test it per the description that follows. To replace the switch, refer to Figure 11.
@ Remove the wires from the suspected switch. @ Set multimeter to ohms scale. Set ohms scale to Rx 1, then zero the meter. ® Connect multimeter leads to appropriate LED switch contacts (see Figure 11 for designation of switch contacts). @ Check contacts (push and release the switch button) for closed and open continuity. @ If the contacts do not operate sharply or always temain closed or open, then replace the LED switch as outlined in the figure.
- Potentiometer Replacement Unsolder and remove the wires from the faulty potentiometer. Using a 5/64-inch Allen wrench, loosen both set screws on the side of the shield control knob; remove this knob. Then remove the flat hex nut on the outside of the panel with a wrench, as well as the internal-tooth lock washer.
Replace the potentiometer with a new one, making sure the hex nut and knob are tightened securely. Then resolder the three harness wires.
To remove LED switch: Remove all wires from the faulty switch. Turn the switch counterclockwise while holding the black cone-shaped bushing on the outside of the control panel. Install a new switch using the reverse procedure. Reconnect the hamess wires. Warlords ™/Cocktail
NORMALLY CLOSED y (N.C) CONTACT
NORMALLY OPEN (N.O.) CONTACT
\ LIGHT-EMITTING-DIODE COMMON ‘ TACT! common (LED) CONTACTS
Figure 11 Replacing Player Controls
Warlords “Cocktail
D. Monitor Removal
- Be sure the game is unplugged from its wall outlet! Unlock and open the table top.
- Lift up the “U’-shaped security bar, located along the inside wall of the cabinet. Remove the bar entirely from the cabinet. Remove the access panel from the game.
- Locate the 6-pin monitor and 3-pin power connectors underneath the monitor, just above the power supply transformer. Unplug these connectors.
- Remove the four Phillips-head screws and flat washers (one set at each corner of the monitor screen) that attach the monitor to the cabinet. Remove these screws.
- Carefully lift the monitor chassis up and out of the cabinet.
Disassemble in the order indicated. (Circled numbers match the steps above.)
Figure 12 Monitor Removal
Warlords ™/Cocktail
REGULATOR/ AUDIO II PCB
Figure 13 Printed-Circuit Board Removal
E. Printed-Circuit Board Kemoval
You may wish to remove the game printed-circuit board (PCB) or the Regulator/Audio || PCB for service or inspection. To do this, refer to Figure 13 and proceed as follows:
- Game PCB Removal @ Unlock and open the table top. @ Remove the nylon tie wraps from the top side of the game PCB. Then remove the 44-pin edge connector. @ Locate the Phillips-head screws that extend through the PCB and into the two wood blocks near the top of the game. Remove these two screws and the associated fiber washers. @ Remove the PCB from the game by sliding it up out of the plastic PCB retainers. Reinstall the PCB, making sure that the 44-pin edge connector is properly piugged in. Note that the connector is keyed to fit on only one way, so if it doesn’t slip on easily, don’t force it! A reversed connector will probably damage your game and will void the warranty. Check that the operation of the game is correct and perform the self-test. This is especially important with any game when you replace a PCB.
Regulator/Audio Il PCB Removal Unlock and open the table top. Remove the three plug-in connectors. Locate the Phillips-head screw that extends through the PCB and into the wood at the top of the PCB. Remove this screw and its associated washers. Remove the PCB from the inside wall of the cabinet by pulling it up and out of the wood retainer.
Warlords™/Cocktaii
REGULATOR’ AUDIO II PCB
PLUG-IN WIRE CONNECTORS
Figure 14 Speaker Replacement
F. Speaker Replacement
If the loudspeaker should ever need to be replaced, follow the instructions below and refer to Figure 14. Probably the only cause of speaker failure is an open voice coil or a ruptured cone, but both of these failures are highly unlikely.
Open the table top. Unplug both speaker-wire connectors. li the speaker is stap/ed to the cabinet wall, use a flat-bladed screwdriver to pry loose the staples that secure the speaker. If screws are used to secure the speaker, use a very short-handled Phillips screwdriver to remove the four screws. For greater ease in reaching these screws, and to prevent slipping and damaging the Regulator/Audio II PCB, remove this PCB first.
G. Game Operation
With this manual you received three large sheets that contain the wiring and schematic diagrams for the Warlords™/Cocktail game. Sheet 1, Side A, includes information that shows the arrangement of these diagrams. These diagrams include information that explains the functions of the circuits and defines inputs and outputs.
Atari’s Warlords™ is a microprocessor-controlled game. The microprocessor is mounted on the game PCB. The game PCB receives switch inputs from the control panels and coin acceptors. These inputs are processed by the game PCB and output to the monitor, Regulator/Audio Il PCB, loudspeaker, coin counter, and control panels.
The Regulator/Audio || PCB performs two functions: 1) it regulates the + 10.3 VDC from the power supply to +5 VDC, and 2) it amplifies the audio out- Warlords ™/Cocktail
put from the game PCB. The +5 VDC from the Regulator/Audio Il PCB provides most logic power to the game PCB. The audio output from the Regulator/- Audio II PCB directly drives the game speakers and is controlled by the volume control, mounted on the bracket inside the game.
The power supply is the source of all voltages in the game. These voltages are protected by four fuses (F3 thru F6) on the power supply chassis. The primary winding of the power supply transformer is protected by the fuses F1 and F2 on the power supply chassis.
Figure 15 illustrates the distribution of power in this game. Figure 16 illustrates the distribution of signals.
Warlords™/Cocktail
MONITOR
GAME PCB
INTERLOCK SWITCH
REGULATOR! AUDIO 11 PCB
POWER SUPPLY
COIN ACCEPTORS
POWER ON/OFF SWITCH
Figure 15 Power Distribution
Warlords Cocktail
MONITOR
GAME PCB be
UTILITY COIN SWITCH
VOLUME CONTROL
SELF-TEST SWITCH
REGULATOR! AUDIO II PCB
SLAM SWITCH
SPEAKER
COIN ACCEPTORS
COIN COUNTER
Figure 16 Signal Distribution
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This chapter provides you with the necessary information for ordering replacement parts for your Warlords™/Cocktail game. Please note that, for simplicity, common hardware has been deleted from most of these parts lists. This includes screws, nuts, washers, bolts, etc.
The parts lists are arranged in alphanumeric order. For example, all “A-” prefix numbers come first. Following this are numbers in sequence evaluated up to the hyphen, namely 00- thru 99-, then 000598- thru approximately 190000-.
When ordering parts from your distributor, give the part number, part name, applicable figure number of this manual, and serial number of your game. This will help to avoid confusion and mistakes in your order. We hope the results will be less downtime and more profit from your game.
Illustrated
Parts Lists
Warlords /Cocktail
037184-01 (Tabletop Panel) aeane (Eyebolt)
037183-01 (Tabletop Retainer)
036078-01 035851-01 (Mon. Bezel) | things)
000268-02 034536-03 one, An36189.01 (interl. Sw. Mnitg. Brkt.) (interl. SwJBrkt. Assy.) 007882-02 (inter. Sw. Cover)
78-3118 {Tabletop Support) 036788-01 (Security Bar)
035867-02 (Mon. Overlay) 036774-01 (Grille)
48-004 71-2110 —_ eo (Lock) 02-305010: (T-Molding) 000869-01 (Spkr. Grille) Control Panel Assy.— see Figure 20
A A037173-01 (Cabinet Assy.)
e
036772-01 (Access Panel)
036773-01 Base Grille 78-3205 ‘ ) 78-3206 NOTICE TO ALL PERSONS RECEIVING THIS DRAWING. (Endcap) bi CONFIDENTIAL: Reproduction forbidden without the (Adj'ble Foot) Specific written permission of Atari, Inc., Sunnyvale, CA This drawing is only conditionally issued, and neither receipt nor possession thereot conters or transfers any right in, or license to use, the subject matter of the draw: ing oF any design or technical information shown thereon, or any right to reproduce this drawing or any part there: of. Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's written license, ‘no right to reproduce this drawing 1s granted or the subject matier thereof unless by written agreement with or written permission from the corporation,
Figure 17 Cabinet-Mounted Assemblies A037172-01 B
Warlords ™/Cocktail
Schematics, Self-Test Labels & Manuals— > see parts list on next page
A036083-01 or A036084-01 (Monitor Assy.) 037188-01 (Glass Tabletop) 035745.04 \ (PCB Retainer)
036764.01 (Hook-Type Cam) 62.041 (Util, Coin Sw.) 036774.02 (Grile) 75-9910NO ‘n03620.01 (Stamped Nut) (Vol./Self-Test/ qweren) Coin Sw. Assy.) ’ 69-001 (Self-Test Sw.) 036321-01 (Vol. Ctrl/Self Test/- Coin Sw. Brkt.) A037047-01 (Main Harness)
Game PCB Assy.— see Figure 19
034536-03 (Vibr. Damper) Reg./Audio Il PCB— see Figure 18 037197-01 = Coin Acceptor/Mount Assy.— (Grille) see Figure 22
035848.01 03724501 kpl: (Backplate) (Support)
A007638-01 aosasaios, > (Slam Sw. Assy.) A034863-08 or 004339.01 ‘A035989-08 — . (Slam-Sw. Brkt.) (Power Cord)’
037335-01 (Brace) Power Supply Assy.— see Figure 21 A037246-01 (Leg Assy.) ( 4 A002465-01 a (Coin Counter) ard tel 009992-01 NOTICE TO ALL PERSONS RECEIVING THIS DRAWING ‘oin Box| IDENTIAL Reproduction forbidden without the : ) (On/OH Sw. Cover) Specie watten permission of Aton inc. Sunnyvale, CA This drawing is only conditionally issued, and neither 61-162A receipt nor possession thereo! confers or transfers any Tight in, or license to use, the subject maiter of the draw: (On/Off Switch) ing or any design or technical information shown thereon 1 nor any right to reproduce this drawing or any part 0 thereol. Except for manufacture by vendors of Alar. Ine (On/Off Sw. Mntg, Plate) and for manutacture under the corporation's written license. no right to reproduce this drawing is granted or the subject matter thereof unless by written agreement with or written permission from the corporation’
Figure 17 Cabinet-Mounted Assemblies A037172-01 B
Warlords™/Cocktail
Figure 17 Cabinet-Mounted Assemblies Parts List
Part No. Description
A002465-01 Coin Counter
| A007638-01 | Slam Switch Assembly | (inc/udes bracket) |
| A034631-01 | On/Off Switch Assembly | (includes mounting plate) |
A034841-08 U.S. Strain-Relief Power Cord A034863-08 German Strain-Relief Power Cord A035989-08 Australian Sirain-Relief Power Cord A036083-01, or 14-Inch Matsushita Color Monitor Assembly or A036084-01 14-Inch Sanyo Color Monitor Assembly A036189-01 Interiock Switch/Bracket Assembly (modified for safety) A036320-01 Volume/Self-Test/Utility Coin Switch Assembly (includes bracket) A036775-01 Coin Box Assembly (includes lock) A037047-01 Main Harness Assembly
| A037173-01 | Wood Cabinet Assembly | (includes legs, support arm, grilles, locks and tabletop) |
A037246-01 Leg Assembly {includes support, brace, adjustable feet and endcaps) The following seven items are the technical information supplements to this game: DP-177-01 Warlords ™Cocktail Schematic Drawings (Sheet 1) DP-177-02 Warlords/Cocktail Schematic Drawings (Sheet 2) ST-177-01 and -02 Labels with Self-Test Procedure and Option Switch Settings TM-153, or Matsushita 14-Inch Color Monitor Manual, or TM-157 Sanyo 14-Inch Color Monitor Manual 1M-177 Warlords/Cocktail Operation, Maintenance and Service Manuat 02-305010 25/32-Inch Black Plastic T-Molding 19-9032 50-Ohm, 12z-Watt, Wirewound Rheostat (volume control) 48-004 5-Inch, 8-Ohm, 5-Watt Round High-Fidelity Speaker 61-1624 DPST Power OniOff Toggle Switch 62-041 SPDT Momentary-Contact Pushbutton Utility Coin Switch with Black Cap 69-001 DPDT Slide Switch (for self-test) 71-2110 Panel Cartridge Lock Mechanism (does not include black hook-type cam)
| 75-9910NO | 5/8-11 Steel Stamped Nut | (for utility coin switch) |
78-24012 5-Inch Beaded Nylon Tie-Wrap (for PCB edge connector) 78-3118 Right-Hand Tabletop Support (acceptable substitute is part no. 178015-001, left-hand support) 78-3205 Square Black Endcap for Leg Assembly 78-3206 Adjustable Foot 82-406 # 4-20 x 2-Inch-Long Eyebolt, with 34-Inch Threads 000268-02 Inierlock Switch Mounting Bracket 000869-01 Speaker Grille 004339-01 Slam-Switch Bracket 006450-01 On/Off Switch Mounting Plate 007882-02 Interlock Switch Cover 009992-01 On/Off Switch Cover 034536-03 Foam Vibration Damper 035745-04 16-Inch-Long Plastic PCB Retainer 035848-01 Backplate for Attaching Leg 035851-01 Tabletop Hinge 035867-02 Smoke-Color Acrylic Monitor Overlay [Continued on next page]
Warlords™/Cocktail
Figure 17 Cabinet-Mounted Assemblies, continued Parts List
Part No. Description 036078-01 Cardboard Monitor Bezel 036321-01 Bracket for Volume Control, Self-Test and Utility Coin Switches 036686-01 Card with Game Pricing Labels 036764-01 Black Hook-Type Cam for Locking Tabletop 036772-01 Access Panel 036773-01 Grille in Cabinet Base 036774-01 Upper End-Panel Grille (about 9 inches long) 036774-02 Upper End-Panel Grille (6% inches long) 036788-01 “U"-Shaped Security Bar 037183-01 Black Retainer for Tabletop Glass (two per game) 037184-01 Wood Tabletop Panel 037188-01 Tempered-Glass Tabletop with Graphics 037197-01 Grille underneath Control Panel 037245-01 Leg Support 037335-01 Leg Brace
A035435-02 Figure 18 Regulator/Audio I! PCB Assembly D
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING
CONFIDENTIAL: Reproduction
specifi Al lon.
agreement
R5-z. TIP 32 az
ia Trea] R4 33IRS C2 GD alae CRA
Fy Fl Risto ee PERI RIG |O' eo ce
cS C4
he TOAZ002 A ase
ood C6GD $
wis} I
“Se
3500, Fi lo
+E TDAZO02A
cleo S AR24, 10, 7W]— [o} R32 fog 4425wh os as 7812 C225 foram c23 “feee +
Res C3 422}
7905
Reet cl
- R2l ew R3I —] 224,10W a Warlords ™/Cocktail
Warlords Cocktail
Figure 18 Regulator/Audio Il PCB Assembly Parts List
Part No. Description (Reference Designations and Locations in Bold)
12-52P7 2.7 Ohm, + 5%, 1W Resistor (R5) 16-54PO, 4 Ohm, +5%, 5W Wirewound Resistor (R25) 19-100P1015 -1 Ohm, + 3%, 7W Wirewound Resistor (R24)
| 19-315102 | 1K Ohm Vertical PCB-Mounting Cermet Trimpot | (R8) |
| 24-250108 | 1000 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor | (C13) |
| 24-250477 | 470 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor | (C1, 4, 12) |
| 24-350226 | 22 uf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor | (C24, 31) |
| 24-350338. | 3300 uf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor | (C9, 10, 18, 19) |
| 24-500105, | 1 uf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor | (C22, 23) |
29-088 .1 uf Ceramic-Disc 25V Radial-Lead Capacitor (C3, 11, 20, 21)
| 31-1N4002 | 100V 1-Amp. Silicon Rectifier Type 1N4002 Diode | (CR1, 4-8) |
| 33-TIP32 | PNP Power Transistor, Type TIP32 | (Q2) |
| 34-2N3055, | NPN Silicon Transistor, Type 2N3055 | (Q3) |
| 37-LM305 | 5V Linear Voltage Regulator | (Q1) |
| 37-7812 | +12V Voltage Regulator, Type 7812 | (Q8) |
| 37-7905 | -5V Voltage Regulator, Type 7905 | (Q9) |
72-1608C #6-32 x ¥-Inch Cross-Recessed Pan-Head Corrosion-Resistant Steel Machine Screw 75-F60405, #6-32 x 1%4-Inch Binder-Head Nylon Screw 75-99516 #6-32 Nut/Washer Assembly
| 78-16008 | Thermally Conductive Compound | (Q3) |
78-16014 Thermally Conductive Silicon Insulator (Q2, 9)
| 79-58306, | 6-Position Connector Receptacle | (J6, 9) |
| 79-58308 | 9-Position Connector Receptacle | (J7) |
| 79-58346 | 12-Position Connector Receptacle | (J10) |
| 79-58354 | 4-Position Connector Receptacle | (J8) |
020670-01 Test Point 034531-01 Heat Sink
| 110000-010 | 1 Ohm, + 5%, %W Resistor | (R10, 19) |
110000-100 10 Ohm, + 5%, %4W Resistor (R11, 20, 29, 30) 110000-101 100 Ohm, + 5%, %4W Resistor (R4, 12, 22)
| 110000-102 | 1K Ohm, + 5%, %W Resistor | (R27, 28) |
110000-103 10K Ohm, + 5%, YW Resistor (R13, 14) 110000-271 270 Ohm, + 5%, 4W Resistor (R1) 110000-330 33 Ohm, + 5%, YW Resistor (R3)
| 110000-392 | 3.9K Ohm, + 5%, %W Resistor | (R6) |
| 110000-562 | 5.6K Ohm, + 5%, %4W Resistor | (R32, 33) |
| 110000-752 | 7.5K Ohm, + 5%, YW Resistor | (R7) |
110001-221 220 Ohm, + 5%, YeW Resistor (R9, 21) 116000-220 22 Ohm, + 5%, 10W Wirewound Resistor (R31)
| 122002-102 | .001 uf Ceramic-Disc Minimum 25V Radial-Lead Capacitor | (C2, 7, 16) |
| 122004-224 | .22 uf Ceramic-Disc 25V Capacitor | (C6, 8, 15, 17) |
| 100015-103 | .01 uf Ceramic-Disc 25V Radial-Lead Capacitor | (C5, C14) |
| 137151-002 | Type TDA2002A 8W Linear Audio Amplifier Integrated Circuit | (Q5, 7) |
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
Warlords ™/Cocktail
Figure 19 Warlords” Game PCB Assembly, continued Parts List
Part No. Description (Reference Designations and Locations in Bold) C012294-01 Audio 0 N-Channel MOS/LSI Custom Chip (B3/4) 24-250107 100 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C29, 65) 28-101101 100 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C10) 28-101390 39 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C68) 29-088 -1 uf Ceramic-Disc 25V Radial-Lead Capacitor (C1-9, 11-28, 30-35, 37-43, 45-63, 66, 69) 31-1N100 100V Type-1N100 Switching Diode (CR2) 31-1N4001 75V Type-1N4001 Switching Diode (CR3, 5) 33-2N3906 Type-2N3906 PNP Switching and Amplifying Transistor (Q2, 8) 34-2N3904 Type-2N3904 NPN Silicon Transistor (Q1, 7, 9) 34-2N6044 Type-2N6044 Darlington NPN Transistor (Q3-5) 37-LM324 Type-LM324 Integrated Circuit (K9) 37-LM339, Type-L$339 Integrated Circuit (A5) 37-74LS00 Type-74LS00 Integrated Circuit (C4) 37-74LS04 Type-74LS04 Integrated Circuit (B6, J6) 37-74LS08 Type-74LS08 Integrated Circuit (C7) 37-74LS10 Type-74LS10 Integrated Circuit (C5, F3)
37-74LS32 Type-74LS32 Integrated Circuit (D4, E4, N9) 37-74LS42 Type-74LS42 Integrated Circuit (D3) 37-74LS74 Type-74LS74 Integrated Circuit (N4, K6, B7) 37-74LS83 Type-74LS83 Integrated Circuit (E5, F5) 37-74LS86 Type-74LS86 Integrated Circuit (D6) 37-74LS90 Type-74LS90 Integrated Circuit (B5) 37-74LS139 Type-74LS139 Integrated Circuit (C3) 37-74LS153 Type-74LS153 Integrated Circuit (H4, J4, K4, L4, M4, P7)
37-74LS157 Type-74LS157 Integrated Circuit (E7, F7, H7, J7, C6) 37-74LS163A Type-74LS163A Integrated Circuit (M8, K7, P4, P5, P6, N5, N6) 37-74LS166 Type-74LS166 Integrated Circuit (D7, J8) 37-74LS174 Type-74LS174 Integrated Circuit (D5, D8) 37-74LS175. Type-74LS175 Integrated Circuit (L6) 37-74LS244 Type-74LS244 Integrated Circuit (B1, C1) 37-74LS245 Type-74LS245 Integrated Circuit (E2) 37-74LS257 Type-74LS257 Integrated Circuit (L2, K2, M3, M5, F8, H8) 37-74LS259 Type-74LS259 Integrated Circuit (P9) 37-74LS273 Type-74LS273 Integrated Circuit (F4, L7) 37-74LS373 Type-74LS373 Integrated Circuit (F2) 37-74S04 Type-74S04 Integrated Circuit (P3) 37-74S74 Type-74S74 Integrated Circuit (N8) 38-MV5053 Type-MV5053 Light-Emitting Diode (CR1) 41-3003 100 uH, +5%, Hot-Molded Plastic Fixed R.F. Choke (L1) 62-001 SPST Momentary Pushbutton Switch (A7) 66-114P1T 4-Station, Single-Throw, Dual-Inline-Package Bit Switch (L9) 66-118P1T 8-Station, Single-Throw, Dual-Inline-Package Bit Switch (J2, M2) 79-42C16 16-Contact Medium-Insertion-Force Integrated Circuit Socket (M6, N7) 79-42024 24-Contact Medium-Insertion-Force Integrated Circuit Socket (K/L1, M1, D1, E/F1, H1, J/K1, F/H6, E6) [Continued on next page]
Warlords™/Cocktail
Figure 19 Warlords” Game PCB Assembly, continued Parts List
Part No. Description (Reference Designations and Locations in Bold) 79-42C40 40-Contact Medium-insertion-Force Integrated Circuit Socket (B3/4, C2)
| 81-4302 | Nylon Snap-In Fastener | (Q3-5) |
| 90-102 | 12,096 MHz, + .005%, Crystal | (¥1) |
90-6010 Microprocessor (C2)
| 90-7031 | Random-Access Memory | (H3, J3, K3, L3, H5, J5, K5, L5) |
| 90-7033 | Random-Access Memory | (N14, P1) |
| 90-7035 | Random-Access Memory | (L8, K8)° |
020670-01 Test Point
| 03715301 | Read-Only Memory | (K/L1) |
| 037154-01 | Read-Only Memory | (M1) |
037155-01 Read-Only Memory (D1) 037156-01 Read-Only Memory (E/F1)
| 037157-01 | Read-Only Memory | (H1) |
| 037158-01 | Read-Only Memory | (J/K1) |
037159-01 Read-Only Memory—Graphics (E6, F/H6) 037161-01 Programmable Read-Only Memory (M6) 037235-01 Programmable Read-Only Memory (N7) 100015-103 .01 uf Ceramic-Disc 25V Radial-Lead Capacitor (C64)
| 110000-102 | 1K Ohm, +5%, %W Resistor | (R20-23, 26-32, 37, 38, 42, 62-69, 74-81, 84, 85, 88, 90, 91) |
110000-103 10K Ohm, +5%, %W Resistor (R1-19, 24, 33, 44, 92, 93, 96) 110000-104 100K Ohm, +5%, %4W Resistor (R50-53)
| 110000-105 | 1M Ohm, +5%, YW Resistor | (R34) |
110000-122 1.2K Ohm, +5%, YW Resistor (R72)
| 110000-153 | 15K Ohm, +5%, %4W Resistor | (R36) |
110000-182 1.8K Ohm, +5%, YW Resistor (R71, 73) 110000-183 18K Ohm, +5%, ‘4W Resistor (R87)
| 110000-221 | 220 Ohm, +5%, YW Resistor | (R45-49, 94) |
| 110000-471 | 470 Ohm, +5%, %W Resistor | (R54-61, 82, 83) |
| 110000-472 | 4.7K Ohm, +5%, YW Resistor | (R25) |
110000-563 56K Ohm, +5%, %W Resistor (R35) 110000-681 680 Ohm, +5%, %4W Resistor (R95) 121008-105, 1uf, +10%, Polyester 50V Radial-Lead Capacitor (C44) 122002-102 .001 uf Ceramic-Disc 25V Radial-Lead Capacitor (C36) 122004-224 .22 uf Ceramic-Disc 25V Radiai-Lead Capacitor (C67) 131000-001 39 V, + 10%, 0.4 W, Type-1N748 Zener Diode (CR4)
78-6900401 (Foam Tape)
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the spe- ‘A037186-01 (Ctrl, Panel) Warlords™/Cocktail
A037048-01 (Harness)
62.039 {LED Switch) 75-9910WO (Stamped Nut) 75.0178 (Spacer)
19-9022 (Potentiometer)
cific written permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor possession thereo! confers or transfers any right in, or
right to reproduce this drawing or any part thereot. Except 033127-01 g@ > ’ 73-834 license to use, the subject matter of the drawing or any (Knob) design or technical information shown thereon, nor any {or manufacture by vendors of Atari, Inc., and tor manutac: ture under the corporation's written license, no right to re: (Sw. Bushing) produce this drawing is granted or the subject matter thereof unless by written agreement with or written permis: sion ‘rom the corporation,
Figure 20 Control Panel Assembly A037185-01 A
Parts List
Part No. Description
A037048-01 Control-Panel Harness Assembly A037186-01 Control Panel with Graphics 19-9022 5K Ohm, + 20%, Linear Slip-Clutch Potentiometer 62-039 Momentary-Contact SPDT Light-Emitting-Diode Switch with Red Cap 73-834 Black Knob with Skirt 75-017S Spacer for Light-Emitting-Diode Switch 75-9910W0 #15/32-32 Stee| Stamped Nut 78-6900401 Vinyl Foam Single-Coated-Adhesive Tape, 1/16-inch thick x %-inch wide (specify no. of inches required) 033127-01 Black Molded Switch Bushing
Warlords ™/Cocktail
79-441001 (Fuse Post) onseee01 Se-2017002 (Fuse Block Cover) 46.2013002 (Fuse) (Fuse)
03448201 (Chassis)
A034623-03 (Power Supply Harn. Assy.) A035674-01 3206 (Volt. Plug Assy.) 7%: (Fuse Block)
78-2708 (Bushing)
78-70501SC: TOP VIEW (Bracket) NOTICE TO ALL PERSONS RECEIVING THIS DRAWING rackel CONFIDENTIAL. Reproduction forbidden without the 29.053 Specific written permission of Atari, Inc... Sunnyvale, CA This drawing is only corssitionally’ issued, and neither (Elec, Cap.) receipt nor possession thereo! conters or transfers any right in, oF license to use, the subject matter of the draw: :ng or any design or technical information shown thereon, nor any right to reproduce this drawing or any part thereof. Except for manufacture by vendors of Alan, Inc., and for manufacture under the corporation's written license, no right to reproduce this drawing iS granted or the subject matter thereof unless by written agreement 442000-001 with or written permission from the corporation BOTTOM VIEW (Power Trans.) A006555-01 (Rect. PCB Assy}
A034630-01 79-15021001 (RFI Filter Assy} (Block)
A034629-01 {AC Harness Assy )
Figure 21 Power Supply Assembly for Color Raster-Scan Games A036099-01 A
Warlords™/Cocktail
Figure 21 Power Supply Assembly for Color Raster-Scan Games Parts List
Part No. Description A006555-01 Rectifier Printed Circuit Board Assembly A036098-01 Transformer and Harness Assembly (inc/udes shielded power transformer) A034629-01 AC Harness Assembly A034630-01 RFI Filter Assembly A035674-01 Voltage Plug Assembly (set of four p/ugs) 29-053 26,000 uf 15V Electrolytic Capacitor 46-2013002 3-Amp. 250V 3AG Slow-Blow Glass Cartridge-Type Fuse 46-2017002 7-Amp. 250V 3AG Slow-Blow Glass Cartridge-Type Fuse 78-2708 Nylon Type 6/6 Hole Bushing with 5/8-Inch Inside Diameter x 55/64-Inch Outside Diameter x Ya-Inch Thick 78-70501SC 2-Inch-Diameter Capacitor Mounting Bracket 79-15021001 2-Circuit Single-Row Terminal Block 79-3206 5-Position 3AG Fuse Block with %-Inch Quick-Disconnect Terminals 79-4411006 Panel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post 034544-01 Fuse Block Cover 142001-001 Shielded Power Transformer Only (with isolation windings)
Warlords™/Cocktail
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING 99-15038 CONFIDENTIAL: Reproduction forbidden without the 99-15001 thru 99-18012 e701 for Butlon) Specific written permission of Atari, Inc., Sunnyvale, CA (Ret. Button) This drawing is only conditionally’ issued, and neither receipt nor possession thereo! coniers or transiers any fight in, or heense to use, the Subject matter of the draw ing or any design or technical mformaticn shown theieon, ‘ot any right to reproduce ‘this drawing or any. part tMereot, Except for manufacture by vendors oF Atar, Ine., and tor manutaclure. under the corporation's. written license, no right to reproduce this drawing is Granted or the subject matter thereo! unless by writven agreement with oF written permission from the Corporation
——— 099.15082
(Spring for Button) 99-15051 (Lamp Holder) S&
—— 99-45026 99-15056 (Coin Inlet) (Screw for Bezel)
(Bezel for Cover)
99-15036 (Cover)
99-15055 99-18041 (Retng. Screw) iLockout Coil) / 99-15053 (Lockt. Coil Spring) 99-15054 f " 99-15027 (Pivot for Lever) (Coin Ret Box)
—+——— 99-15028 (Coin Ret. Box)
99-15037 (Sw. Adjuster) 99-15056 (Screw for Bezel) 99-15060 _o (Sw. Cover)
A036597-01 (Harness—not shown for clarity) 99-15029 (Bracket)
99-15042. (Switch)
Figure 22 Double Coin Acceptor/Mount Assembly A036693-xx A
Warlords™/Cocktail
Figure 22 Double Coin Acceptor/Mount Assembly Parts List
Part No. Description A036597-01 Double Coin Acceptor Harness Assy. 99-15001 Coin Return Button with U.S. 25¢ Price Plate 99-15002 Coin Return Button with U.S. $1 Price Plate 99-15003 Coin Return Button with German 1 DM Price Plate 99-15004 Coin Return Button with German 2 DM Price Plate 99-15005 Coin Return Button with German 5 DM Price Plate 99-15006 Coin Return Button with Belgian 5 Fr Price Plate 99-15007 Coin Return Button with French 1 Fr Price Plate 99-15008 Coin Return Button with Japanese 100 Yen Price Plate 99-15009 Coin Return Button with British 10 Pence Price Plate 99-15010 Coin Return Button with Australian 20¢ Price Plate 99-15011 Coin Return Button with Italian 100 Lire Price Plate 99-15012 Coin Return Button with U.S. 50¢ (2 x 25¢) Price Plate 99-15025 Left Half of Coin Inlet 99-15026 Right Half of Coin Inlet 99-15027 Side Plate of Coin Return Box 99-15028 Base Plate of Coin Return Box 99-15029 Switch Bracket 99-15030 Flap for Lockout Coil (U.S. 25¢) 99-15036 Coin Return Cover 99-15037 Switch Adjuster 99-15038 Bezel for Coin Return Button 99-15039 Bezel for Coin Return Cover 99-15040 Coin Return Lever 99-15041 Lockout Coil 99-15042 Coin Switch for U.S. 25¢ 99-15051 Lamp Holder 99-15052 Spring for Coin Return Button 99-15053, Spring for Lockout Coil 99-15054 Pivot for Coin Return Lever 99-15055 Retaining Screw 99-15056 Screw for Both Bezels 99-15060 Switch Cover
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Warlords™/Cocktail
YOUR COMMENTS, PLEASE! 1st printing
Your comments will assist Atari in improving the usefuiness of our publications. They are an important part of preparing for revisions of manuals and parts catalogs. No postage stamp is necessary if mailed in the U.S.A.
If you have any technical questions about certain Atari or Kee Games products, or are requesting additional publications, we will immediately forward your note to the appropriate person. | Page: Comments:
Fill in if you wish a reply:
Name
Firm 1 Distributor
Address OU Operator
City _ State Zip OC Other.
Area Code _. Phone
BUSINESS REPLY MAIL
FIRST CLASS PERMIT NO. 1004 SUNNYVALE, CA
POSTAGE WILL BE PAID BY ADDRESSEE
Atari, Inc. Attn.: Field Service/Coin-Op Division P. O. Box 427 Sunnyvale, California 94086
Second fold No Postage Necessary if mailed in the United States
eBpe siyy odes “WO aut) siyy Buoye yng
ae
@ EEE GE ME PETE TES
°
BS AS SR ES ES
Warranty
Seller warrants that its printed circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its television monitors (in games supplied with monitors) are free from defects in material and workmanship under normal use and service for a period of thirty
- days from date of shipment. None of the Seller's other products or parts thereof are warranted.
If the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer’s account for such products which are returned to Seller during said warranty period, provided:
- Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
- Such products are returned prepaid to Sellers’ plant; and
- Seller's examination of said products discloses to Seller’s satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing.
In no event shall Seller be liable for loss of profits, toss of use, incidental or consequential damages.
Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms of this order, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products under this order.
The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to yourself and others. Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety.
Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.
This document is and contains confidential trade secret information of Atari, Inc.
This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc.
Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc. © © ©
© s s %
ATARI INC 1265 BORREGAS AVENUE P.O. BOX 427 SUNNYVALE, CALIFORNIA 94086 408/745-2000 * TELEX 35-7488
© > Werner Communications Company