CATHODE RAY TOMES

Missile Command Caberat TM-158 1st Printing

Missile Command (rev 3, A035467-02/04 PCBs) (Atari, 1980) · Technical Manual · 52 pages · 46 sections · original scan

Page 1

Operation, Maintenance

and Service Manual Complete with Illustrated Parts Lists

L5¥UdU) GINESUUWUUC>)

Page 2

GAME SERIAL NUMBER LOCATION Your game’s serial number is stamped on a plate on the outside of the game. The same number is also stamped on the chassis of the TV monitor, Regulator/Audio Il PCB, and Game PCB. Please mention this number whenever calling your distributor for service.

GAME SERIAL # IDENTIFICATION TAG

TV MONITOR

REGULATORIAUDIO Il PCB

GAME PCB

Page 3

CABARET

Nill Le COMMVAN

Operation, Maintenance and Service Manual

Complete with Illustrated Parts Lists D

Published by: ATARI INC 1265 Borregas Avenue P.O. Box 427 Sunnyvale, California 94086 eS

Copyright © 1980 by Atari, Inc. All rights reserved. Ee

No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for . ATARI’ Cw] A Warner Communications Company public or private use, without permission from the publisher.

Lithographed in the U.S.A. Bd

Page 4

Table of Contents

Location Setup A. NeWParts... 0.0 cece ee cnet nee nena ene 1 B. Game Inspection . 3 C. Game Installation. . 4

  • Voltage Selection .............. 4
  • Interlock and Power On/Off Switches 4 D. Self-Test Procedure ...............- 6 E. Option Switch Settings . 8
  • Bonus Play Feature. . 8
  • CoinMechanism Multipliers . 8
  • Examples of Option Switch Settings . 8 F. GamePlay .. . 10
  • Attract Mode .... - 10
  • Ready-to-Play Mode . 10
  • PlayMode......... . 10
  • High Score Initial Mode +10

Maintenance and Repair 7s ©](-5- Ua] a0 12 B. Fuse Replacement..... C. Opening the Control Panel . 1, LED Switch Replacement........

  • Mini-Trak Ball™ Maintenance and Repair ‘ TV Monitor Removal ............-.00005 . 14 D. E. Printed-Circuit Board Replacement . - 15 F. Fluorescent Tube Replacement . . . 16 G. Game Operation. .... 2.6.6.6 ccc eect eee eens 17

Illustrated Parts Lists

Page 5

List of Dlustrations

Figure 1 Figure 2 Figure 3 Figure 4

Figure 5 Figure 6 Figure 7 Figure 8

Figure 9 Figure 10 Figure 11 Figure 12 Figure 13 Figure 14

Figure 15 Figure 16 Figure 17 Figure 18

Figure 19 Figure 20 Figure 21 Figure 22 Overview of Game 2 Installation Requirements . 4 Voltage Selection ........ 4 Interlock and Power On/Off Switches 5

Location of Self-Test Switch, Volume Control and Option Switches... 6 Self-Test Procedure ..... 2.0... cece eee c eect eee eens 7 Option Switch Settings ........ 9 Opening the Conirol Panel and Replacing Switches ............--. 12

Mini-Trak Ball™ Maintenance and Repair ................00000085 13 TV Monitor Removal ............-...0.0 14 Game and Regulator/Audio II PCB Replacement . 15 Fluorescent Tube Replacement........... Power Distribution Signal Distribution

Ilustrated Parts Lists: Cabinet-Mounted Assemblies ............0- 0000s eee e rece eeeee 22 Fluorescent Light Assembly ........ 00.00 cscs eee teen e neers 24 Control Panel Assembly .. . a Mini-Trak Ball™ Assembly ........0.0 00. :e eee ce eee e nee e ene eeee

Missile Command™ Game PCB Assembly ............- -. 28 Regulator/Audio Il PCB Assembly ...........-.+ . 32 Power Supply Assembly for Color Raster-Scan Games . .. 34 New Coin Door ..... 0.0... cee cece cece cent ee teeeeee 36

Page 6
NOTE

If reading through this manual does not lead to solving a certain maintenance problem, call Tele-Help™ at the Atari Customer Service office in your geographical area, as shown in one of the two maps below. Order all parts from the California office.

WEST and CENTRAL U.S.A.

Parts for all Atari Customers. Sales and Service

Atari Coin-Op Customer Service 1344 Bordeaux Drive, Sunnyvale, CA 94086 Telex 17-1103

(Monday - Friday, 7:30 - 4:00 pm Pacific Time)

From California, Alaska or Hawaii “ (408) 745-2900

a From anywhere else in this area toll-free (800) 538-1611

EAST U.S.A.

Sales and Service Only

Atari Inc. New Jersey Customer Service Office Cottontail Lane, Somerset, NJ 08873 Telex 37-9347

(Monday - Friday, 7:30 - 4:00 pm Eastern time)

From New Jersey z (201) 469-5993

Zz From anywhere else in this area toll-free (800) 526-3849

Page 7

A. New Parts

The Missile Command™/Cabaret game has four new parts. If you have worked on Atari games in the Past, then you should be aware of these important differences. The new parts are: @ 14Inch Color TV Monitor. Made to Atari specifications by either Matsushita or Sanyo, it has high reliability, a compact size, and should maintain its color convergence for a long period of time. @ Power Supply Assembly. It covers a wider voltage range than before, has higher reliability, a smaller overall size, and all fuse numbers and fuse amperages are marked directly on the metal chassis. Its transformer includes isolation windings, so no separate isolation transformer is needed. @ Cabaret Cabinet Design. This more compact cabinet was designed to occupy less than 4 square feet of floor space. © = Mini-Trak Ball™ Assembly. The widely used Trak Bali Assembly has been redesigned and scaled down for use in Atari's compact Cabaret and cocktail-table games.

These new parts, as well as ali other major parts in the game, are illustrated in Figure 1. Throughout this manual, wherever one of these new parts is

mentioned, you will see this symbol: a

Location Setup

Page 8

COLOR TV MONITOR

MINI-TRAK BALL™ CONTROL TV MONITOR SHIELD

CONTROL PANEL GAME SPEAKER

REGULATOR! AUDIO II PCB

ATTRACTION PANEL _

COIN DOOR

ACCESS PANEL

GAME PCB

(<< POWER SUPPLY

POWER ON/OFF SWITCH

Figure 1 Overview of Game

Page 9

B. Game Inspection

A— warninc —A

To avoid possible unpleasant electrical shock, do not touch internal parts of the TV monitor with your hands or metal objects held in your hands!

This new game is ready to play upon removal from the shipping carton. However, your careful inspection is needed to supply the final touch of quality control. Please follow these steps to help us insure that your new game was delivered to you in good condition.

NOTE Do not plug the game in yet!
  • Examine the exterior of the game cabinet for dents, chips, or broken parts. 2. Unlock and open the access panel of the cabinet and inspect the interior of the game as follows: Check that all plug-in connectors (on the game harness) are firmly seated. Replug any connectors found unplugged. DON’T FORCE CONNECTORS TOGETHER. The connectors are keyed so they only go on in the proper orientation. A reversed edge connector will damage a PCB! Check that all plug-in integrated circuits on the game PCB are firmly seated in their sockets.
Note the location of the game’s serial number—it is printed on the special label on the outside of the game cabinet. Verify that the serial numbers also stamped on the Game PCB, Regulator/Audio Il PCB and TV Monitor are all identical. A drawing of the serial number locations is on the inside front cover of this manual. Please mention this number whenever you call your distributor for service. Check all major subassemblies such as the power supply, control panel and TV monitor for secure mounting.

Q

Page 10

Figure 3 Voltage Selection

C. Game

J

Installation

‘Figure 2 Installation Requirements

Power 120 watts Temperature 0 to 38°C (32 to 100°F) Humidity Not over 95% relative Space Required 52x60 cm (20 3/8 x 23% in.) Game Height 140 cm (55 in.)

  • Voltage Selection

Before plugging in your game, make sure that the voltage selection plug on the power supply (see Figure 3) is correct for your location’s line voltage. Check the wire color on the plug and see if it is correct per the list below.

Line Voltage Range Voltage Selection Plug Color

90-110 VAC (100) _—Violet 105-135 VAC (120) Yellow 200-240 VAC (220) Blue 220-260 VAC (240) Brown

  • Interlock and Power On/Off Switches

To minimize the hazard of electrical shock while working on the inside of the game cabinet, two interlock switches have been installed (see Figure 4). One is located behind the access panel and one is behind the coin door. These switches remove all AC line power from the game circuitry when the door or panel is opened.

Check for proper operation of the interlock switches by performing the following steps: @ Plug the AC line power cord into an AC outlet. @ Make sure the access panel and coin door are closed. @ Set the power on/off switch to the “on” position. Within 30 seconds the TV monitor should display a picture. @ Slowly open the access panel. The TV monitor picture should disappear when the panel is opened approximately 2.5 cm (1 inch). Close and lock the access panel and repeat this step with the coin door. @ = If the results of the previous step are satisfactory, the interlock switches are operating properly. If the TV monitor doesn’t go off as described, check to see if the corresponding interlock switch is broken from its mounting or stuck in the “on” position.

Page 11

Missiie Command™/ Cabaret

SWITCH COVER

SAFETY INTERLOCK

POWER ON/OFF SWITCH

Figure 4 Interlock and Power On/Off Switches

Page 12

D. Self-Test Procedure

This game will test itself and provide data to demonstrate that the game’s circuitry and controls are operating properly. The data is provided on the color TV monitor and the game speaker, no

VOLUME CONTROL,

VOLUME INCREASE: TURN CLOCKWISE additional equipment is necessary.

Part of the self-test procedure includes a display of the operator-selectable game options. Therefore, we suggest you run the self-test procedure anytime you need to change the game's options.

To run the self-test, follow the instructions outlined in Figure 6.

SWITCHES

Figure 5 Location of Self-Test Switch, Volume Control and Option Switches

Page 13

Instruction Figure 6 Self-Test Procedure Result if Test Passes Result if Test Fails

  • Set self-test switch to on Position (see Figure 5). Note: entering self-test will set the HIGH SCORE TODAY display to 7500.
  • Roll the Trak Ball control in all directions.
  • Press the following switchea: @ Coin switch trip wires @ Slam switch @ All three fire switches @ Player start buttons
  • Set self-test switch to off Position. After about 5 seconds of frozen attract mode, a low raspy tone is followed by a low beep, then high beep. TV monitor screen displays picture as shown below: ROM OK MAP OK RAM OK + ..plus the options display—see Figure 7 for explanation. Both LED start buttons will also be lighted.

The + moves around on the screen in directions corresponding to Trak Ball control—up to an invisible border along the screen’s edges.

A sound is heard as each switch is pressed. The background color also changes. A continuous raspy tone means V BLANK is malfunctioning. Self-test will not continue. A RAM failure is indicated by a blank or “garbage”-filled screen and a repeated series of 8 beeps, separated by a low raspy tone. See note 1 below. Self-test will not restart. ROM failure is indicated by BAD ROM; see note 2 below. BAD MAP means bit-mapping hardware has failed. BAD CHIP means custom audio I/O chip at location P8/9 has failed.

The + doesn’t move in same direction as ball, or not at all. One of the Steering PCBs on Trak Ball control may be bad, harness wires or connector may be loose, Trak Ball reading circuitry on Game PCB may be bad, or Trak Ball bearings may need oiling.

No sound or color changes are produced when pressing one of these switches: indicates a bad switch, loose harness wires, or loose connector.

Note 1:

High beep in Bad chip series of 8 tones: at location: 1st P4 2nd N4 3rd M4 4th L4 Sth K4 6th J4 7th H4 8th Fa In test no. 1, a low beep means a good chip; a high beep is a bad RAM, as follows:

Note 2: BAD ROM plus some or all of the digits 1 thru 6 are displayed. These numbers show which 2K. of memory are bad. For example, 1 means the first 2K are bad. The + may not appear.
Page 14

E. Option Switch Settings

Settings

  • Bonus Play Feature Missile Command™ is the first Atari game to offer a bonus play for every $1.00 worth of coins inserted. This bonus feature is operator-selectable, meaning you may choose to offer it or not.

With your game set at 50¢ per play, players who deposit four successive quarters or a $1.00 coin, then press the start button, will receive a bonus play. Therefore, players receive 3 plays for $1.00.

This bonus feature encourages players to insert more money than just the minimum 50¢ required for one game.

  • Coin Mechanism Multipliers Since early in 1980, Atari has made available its new coin door which has either two or three mechanisms. All recent Atari game PCBs identify the different mechanisms in a certain pattern.

The right coin mechs are all the same to the game’s logic, regardless of whether you have two or three mechs in your door. In addition, the logic sees the left mech in a 2-mech door and the center mech in a3-mech door as the same. Refer to the diagram below.

[ese Is1] [les [le=4 [lst]

This pattern is important for you to know, so you can correctly set the “multipliers” for each mech. The multipliers determine how much each mechanism will be worth to the game’s logic.

The basic unit of measurement is 25¢, which equals a multiplier of x1. Therefore, if you have a 25¢/25¢/$1 coin door, you will probably want to set the center and right option-switch multipliers at x 1/4. (The left mech in a 3-mech door always has a value of x 1—you cannot change its value.) You can set these multipliers with toggles 3 thru 5 on the Missile Command PCB switch assembly at location R10. For exact settings of these toggles, refer to Figure 7 on the next page.

  • Examples of Option Switch

To explain the options, we have provided below four examples of the most common U.S. situations. The toggles mentioned below only relate to game price, coin mechanism multipliers, and the bonus credit for 4 successive quarters or the $1.00 coin. You should set the toggles relating to other functions as you See fit, although Figure 7 provides “$” signs indicating Atari’s recommendations.

For the first and second examples, we will assume your door (either 2 or 3 mechanisms) has only 25¢ slots:

If you want 50¢ (2 coins) for 1 play, and $1.00 for 3 plays: At R10, set toggles—

54321
ononononoff

At R8, set toggle 3 off. If you want 50¢ (2 coins) for 1 play, and no bonus credit: At R10, set toggles—

54321
ononononoff

At R8, set toggle 3 on.

For the third and fourth examples, we will assume your door (either 2 or 3 mechanisms) has a 25¢ mechanism at left and center, and $1.00 mechanism at right:

if you want 50¢ (2 coins) for 1 play, and $1.00 for 3 plays: At R10, set toggles—

5421
ononoffonoff

At R8, set toggle 3 off.

If you want 50¢ (2 coins) for 1 play, and no bonus credit: At R10, set toggles—

54321
ononoffonoff

At R8, set toggle 3 on.

Page 15

Missile Command™ | Cabaret

Figure 7 Option Switch Settings To change toggle positions cn the switch assemblies, you need not remove the game PCB. The switches, usually colored blue, are easily accessible when the game PCB is mounted in place. When changing the options, verify proper results on the TV monitor display by performing the self-test. Note that changing an option on any toggle will cause an immediate change on the TV monitor screen during the self-test.

Toggle Settings of 8-Toggle Switch on Game PCB (at R10) (RIGHT switch when PCB is in game)

8765432

1 Option

On Off On Off

On On On Off

Off On

Off Off

Not Used

On Off

On On On Off

On 1 coin* for 1 play On Free play Off 2 coins* for 1 play $ Off 1 coin* for 2 plays Right coinmech x 1 $ Right coin mech x 4 Right coin mech x 5 Right coin mech x 6 Center coinmech x 1 $ (Center mech is a left Center coin mech x 2 mech in a 2mech door) English language French language German language Spanish language

Toggle Settings of 8-Toggle Switch on Game PCB (at R8) (LEFT switch when PCB is in game)

87654321Option
OffOffGame starts with 7 cities
OnOnGame starts with 6 cities$
OffOnGame starts with 5 cities
3OnOffGame starts with 4 cities
3OnNo bonus credit

Off 1 bonus credit for 4 successive quarters or a $1 3 coin $ = Switch position is Irrelevant for Missile Command/- Cabaret

Off Off On

OnOnOn
OnOnOff
OnOffOn
OnOffOff
OffOnOn
OffOnOff
OffOffOff

Bonus city every 8,000 points Bonus city every 10,000 points Bonus city every 12,000 points Bonus city every 14,000 points Bonus city every 15,000 points Bonus city every 18,000 points Bonus city every 20,000 points No bonus city

The format of the self-test display is as follows:

Bonus city every chosen) Points (line disappears if no bonus city is

+ Coinage setting 4, 5, 6, or 7 cities (always in English) A B cD

A is the center mech multiplier for 3-mech doors, left mech multiplier If a 2-mech door. This number is either 1 or 2. B is the right coin mech multiplier and is 1, 4, 5, or 6. C: ignore this display. Dis an “X” if switch 3 (of R8) is off. An example of an actual option switch display is as follows:

BONUS CITY EVERY 10,000 POINTS + 2 COINS 1 PLAY 6 CITIES 1 1 x

  • in the U.S..a “coin” is defined as 250. If your game also has a $1 mechanism, you must set the right coin mechanism multiplier as per your choice.

$ Manufacturer's suggested settings

Page 16

F. Game Play

Missile Command™ is a 1- or 2-player game witha color monitor. The game depicts an Armageddonstyle war in which players defend their bases and cities with antiballistic missiles (ABMs). The enemy—the game computer—launches incoming waves of attack missiles. These weapons may be either individual or branching attack missiles, In addition, the enemy occasionally {aunches missiles from a fast-moving “killer” satellite or from bombers. The enemy also launches “‘smart” missiles that usually avoid explosions.

Players receive varying numbers of points for intercepting attack missiles, for having unused missiles still in their bases’ arsenals, and for having their cities undamaged after a missile wave.

The game has five possible modes of operation: attract, ready-to-play, play, high-score initial, and self-test. The latter is a special mode for checking the game switches and computer functions. You may enter this mode at any time. When entered, all game credits are cancelled, and the “HIGH SCORE TODAY” is reset to 7500. A list of eight “highest” scores and initials are also reset onto the screen (to provide player challenge).

  • Attract Mode The attract mode begins when power is applied to the game, after a play or high-score initial mode, or after self-test. This mode is continuous and is only interrupted when a game is paid for and accepted, or when entering self-test.

In this mode, the Missile Command name is displayed, then the computer plays one wave—handling both offense and defense. Following this, the computer displays the high score table, then the Missile Command graphics reappear.

  • Ready-to-Play Mode This mode begins when sufficient coins have been accepted for a one- or two-player game. It ends when the 1 PLAYER START or 2 PLAYER START pushbutton is pressed.

When this mode begins, the message PRESS START scrolls along the bottom of the screen. DE- FEND CITIES and red arrows pointing down to each city also appear on the screen. The displayed pictures are otherwise the same as those shown in the attract mode.

  • Play Mode The play mode begins when either start pushbutton is pressed. The mode ends when the player’s last city is destroyed.

The three bases—Alpha, Delta and Omega—each have 10 ABMs ready to be fired (shown as 4’s). Players must be careful to fire the missiles more or less evenly from among those bases, because no more missiles are granted until the screen resets in preparation for a new wave of attack missiles. If the enemy missiles strike a city or base, the colorful buildings or base will change to the solid color of the landscape.

The game continues until all cities are destroyed. Missile Command™ has no operator-selectable fixed time length. Thus a highly skilled player can play longer than the novice.

During the second wave, a “killer” satellite and/or bomber will appear on the screen, moving quickly and launching attack missiles at the bases and cities. Players get bonus points for shooting down the satellites or bombers.

The general approach for getting high point scores is fairly quickly discovered: try to launch your ABMs when the enemy missiles have just appeared at the top of the screen. Then they are clustered together, where one ABM can usually destroy several enemy missiles. In the later more advanced waves, players can lay out a blanket of explosions.

  • High Score Initial Mode If a player's score exceeds the minimum on the high score initial list, he or she may put up to three initials on this list at the end of the game. Spinning the Trak Ball control changes the letters (A thru Z and a blank are available). Pressing any fire switch will fix that letter on the screen, and move the choice to the next letter. If the player doesn’t enter his or her initials within 90 seconds, three blank spaces will be entered automatically.
Page 17

LE, PLS q,

8 Maintenance

Oo and Repair

All games require certain maintenance to keep them in good working order. Clean, properly maintained games will attract players and earn more profits.

The most important maintenance item is running the self-test every time you collect money from the cash box. Just looking at a game will not tell you if the Mini-Trak Ball™ control or the light-emittingdiode switches are broken, or if LEDs have burned out. The self-test will inform you of any of these possible problems.

Second, you should regularly clean the outside of the game and the coin mechanisms. In addition, you will need to lubricate the Mini-Trak Ball control: for details see this chapter.

Page 18

A. Cleaning

The exterior of the game cabinet and the metal and acrylic surfaces may be cleaned with any nonabrasive household cleaner. If desired, special coin machine cleaners that leave no residue can be obtained from your distributor. Do not dry-wipe the acrylic monitor shield or attraction panel, because any dust can scratch their surfaces and result in fogging the plastic.

B. Fuse Replacement

This game contains six fuses—all on the power supply assembly (not including the TV monitor fuses). Replace fuses only with the same type as listed in Figure 21 of this manual. See the color TV monitor manual for the monitor fuse data. (The Matsushita monitor manual is Atari part number TM-153, and the Sanyo monitor manual is number TM-157.)

C. Opening the Control Panel

Prior to repairing any switch, the Mini-Trak Ball™ or the TV monitor, unplug the game. Then open the coin door. Reach through the opening and remove both sets of carriage bolts, wing nuts, split lock washers, and flat washers, located on the underside of the control panel (see Figure 8). Lift up the control panel’s top edge and swing it towards you.

  • LED Switch Replacement The light-emitting diode (LED) switches on the control panel have a very low failure rate. In case a switch should ever be suspect, first test it per the description that follows. To replace the switch, refer to Figure 8.

@ Remove the wires from the suspected switch. @ Set multimeter to ohms scale. Set ohms scale to Rx1, then zero the meter.

To remove LED switch: @ Remove all wires from the faulty switch. @ Tum the switch counterclockwise while holding the black cone-shaped bushing on the outside of the control panel. Install a new switch using the reverse procedure. @ Reconnect the hamess wires.

NORMALLY CLOSED Ge

Ss (N.C) CONTACT / __~ NORMALLY OPEN _ (N.0.) CONTACT \ \ LIGHT-EMITTING-DIODE (LED) CONTACTS cf COMMON CONTACT To service or replace Mini-Trak Ball Assembly, remove three black screws, self-locking hex nuts and flat washers.

Figure 8 Opening the Control Panel and Replacing Switches

Page 19

Disassemble in the order indicated. (Circled numbers maich the steps described below.)

LUBRICATE HERE (6 PLACES)

Ball Replacement First remove the entire Mini-Trak Ball assembly from the control panel as shown in Figure 8. Now locate the three countersunk machine screws in the acrylic top plate; remove these ‘screws, flat washers, and lock nuts. (When the assembly is installed, these three screws are right underneath the control panel.) Lift off the acrylic top plate; remove and replace the bali. Coupler PCB Replacement

  • Unplug the red connector on the coupler PCB. Remove the two socket-head machine screws, flat and lock washers, and hex nuts from the coupler PCB.
  • Remove the coupler PCB.
  • When replacing this PCB assembly, be certain that the black metal encoding wheel turns freely between the two halves of the red photosensor device.

Figure 9 Mini-Trak Ball™ Maintenance and Repair

Connect multimeter leads to appropriate LED switch contacts (see Figure 8 for designation of switch contacts), Check contacts (push and release the switch button) for closed and open continuity. If the contacts do not operate sharply or always remain closed or open, then replace the LED switch as outlined in the figure.

  • Mini-Trak Ball™ Maintenance and Repair f To maintain this control, you will only have to lubricate the bearings approximately every 2,000 credits. The number of credits can be read off the coin counter, located on the coin door. Use only 2 drops of 3-in-One® oil in each of the ball bearings. (Each Mini-Trak Ball™ control has five bearings.)

For further instructions on how the replace the ball or either coupler PCB, see Figure 9.

Page 20

D. TV Monitor Removal

A— warninc —A; High voltages may exist in any television monitor, even with power disconnected. Use extreme caution and do not touch electrical parts of the TV yoke area with your hands or with metal objects in your hands! If you drop the TV monitor and it breaks, it will implode! Shattered glass and the yoke can fly 6 feet or more from the implosion. Use care when replacing any TV monitor.

If you should need to remove the color TV monitor, follow steps 7 thru 5 below. Refer also to Figure 10.

Disassemble in the order indicated. (Circled numbers match the steps above.) Open the control panel as described in Section C, Opening the Control Panel. Be sure the game is unplugged from its wall outlet! Remove the acrylic TV monitor shield by lifting up and sliding out its lower edge. Remove the small 4” plywood panel that acts as a monitor shield support (it prevents players from flexing the shield downwards). Carefully remove the black cardboard bezel: it lies on top of the wood cleats and is attached with staples. Open the rear access panel and unplug the 3-pin and 6-pin TV monitor harness connectors. Locate the four Phillips-head screws (one at each corner of the TV monitor screen) that attach the TV monitor to the cabinet. Remove these screws. Carefully lift the TV monitor chassis up and out of the cabinet’s top opening.

Figure 10 TV Monitor Removal

Page 21

REGULATOR! AUDIO 11 PCB

MISSILE COMMAND™ GAME PCB

Figure 11 Game and Regulator/Audio il PCB Replacement

E. Printed-Circuit Board Replace

Board Replacement

You may wish to remove the game printed-circuit board (PCB) or the Regulator/Audio II PCB for service or inspection. To do this, refer to Figure 11 and proceed as follows:

1, 2. Open the rear access panel. Locate the securing screw and fiber washer that hold down the PCB in its slots, and remove them. (Each PCB has one set of this fastening hardware.) If you are removing the game board, first remove the two tie wraps that fasten the edge connector to the game PCB. Then unplug the edge connector on the game PCB. If you are removing the Regulator/Audio Il PCB, simply disconnect the three small harness connectors on this board. 4. Carefully slide either PCB straight out of its gray plastic slots. Be careful not to twist the board, as this may loosen connections or components. Replace or repair as required. Reinstall the PCB, making sure that the connectors are properly plugged in. Note that they are keyed to fit on only one way, so if they don’t slip on easily, don’t force them! A reversed connector will probably damage your game and will void the warranty. Replace the securing screw and fiber washer in the PCB. Reinstall the fasteners used to secure the edge connectors to the PCB. Close and lock the rear access panel. Check that the operation of the game is correct and perform the self-test. This is especially important with any game when you replace a PCB. Normally the only adjustments on this game are option switch changes (made on both 8-toggle DiP switches). Unless you are a qualified technician, do not turn the small knob on the Regulator/Audio Il PCB.

Page 22

Figure 12 Fluorescent Tube Replacement

F. Fluorescent Tube Replacement

CAUTION {f you drop a fluorescent tube and it breaks, it will implode! Shattered glass can fly 6 feet or more from the implosion. Use care when replacing any fluorescent tube. To replace the white fluorescent tube behind the front graphics attraction panel, follow this procedure (see Figure 12).

1. Open ihe coin door. Remove the two Y-shaped connectors from the ends of the fluorescent tube. Now carefully remove the tube from its clamps by pulling it towards you. Replace with a new tube. Do not snap the tube in vigorously—you may break it, causing an implosion! Close the coin door and lock it.

Page 23

G. Game Operation

With this manual you received two large sheets that contain the wiring and schematic diagrams for your game. Sheet 1, Side A, includes information that explains the functions of the circuits and defines inputs and outputs.

Atari’s Missile Command™/Cabaret is a microprocessor-controlled game. The microprocessor is mounted on the game PCB. The game PCB receives switch inputs from the control panel and coin mechanism. These inputs are processed by the game PCB and output to the TV monitor, Regulator/Audio II PCB, loudspeaker, and control panel.

The Regulator/Audio Il PCB performs two functions: 1) it regulates the +10 VDC from the power supply to +5 VDG, and 2) it amplifies the audio output from the game PCB. The +5 VDC from the Regulator/Audio II PCB provides most logic power to the game PCB. The audio output from the Regulator/Audio Il PCB directly drives the game speakers and is controlled by the volume control, mounted on the bracket inside the coin door.

The Power Supply is the source of all voltages in the game. These voltages are protected by three juses (F3, F4 and F5) on the power supply chassis. The primary winding of the power supply transformer is protected by the fuses F1 and F2 on the power supply chassis.

Figure 13 illustrates the distribution of power in this game. Figure 14 illustrates the distribution of signals.

Page 24

TV MONITOR

FLUORESCENT LAMP

REGULATORI AUDIO II PCB

0) POWER INTERLOCK SWITCHES

COIN DOOR, GAME PCB

LINE VOLTAGE LINE VOLTAGE

+12 DC

+5vpc =svpc 10.3 DC 6.3 VAC

POWER SUPPLY U4 \

AC POWER CORD

POWER ON/OFF SWITCH

Figure 13 Power Distribution

Page 25

Figure 14 Si ignal Distribution COIN DOOR CONTROL PANEL

VOLUME CONTROL

SELF-TEST SWITCH

TRAK BALL V DIR & CK

TRAK BALL H DIR & CK

RIGHT FIRE

‘<= CENTER FIRE > Ve LEFT FIRE AY STARTILED __\ W ‘START? VW ‘START2LED \ \ COLOR MONITOR

COMP SYNC GREEN

BLUE

RED SPEAKER

> = m™ z fe} oa REGULATOR! AUDIO Ii PCB

Page 26

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 27

Illustrated

Parts Lists

The purpose of this chapter is to provide you with the necessary information for ordering replacement parts for your Atari Missile Command™/Cabaret game. Please note that, for simplicity, common hardware has been deleted from most of these parts lisis. This includes screws, nuts, washers, bolts, etc.

The parts lists have been arranged in alphanumeric order. For example, al! “A-” prefix numbers come first. Following this are numbers in sequence evaluated up to the hyphen, namely 00- thru 99-, then 000598- thru approximately 110000-.

When ordering parts from your distributor, give the part number, part name, applicable figure number of this manual, and serial number of your game. This will help to avoid confusion and mistakes in your order. We hope the results will be less downtime and more profit from your game.

Page 28

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA, This drawing is only conditionally’ issued. and neither receipt nor possession thereat confers or transfers any right in, or license to use, the subject matter 0’ the drawing or any design or technical information shown thereon, 036221-07 nor any sight to reproduce this Grawing ot any part . jereo!, Except for manufacture by vendors of Atarl. Inc, (Trim Cap) 036220-01 and for manufacture under the corporation's written . Shiel license, no right (0 reproduce this: drawing is granted or (Mon. Shield) the subject matter thereo! unless by written agreement with or written permission from the corporation. MinicTrak Ball™ Assy.— eee see Figure 18 y 03608301 or ‘A036084-01 (Monitor)

Contro! Panel Assy.— see Figure 17

036225-01 (Grille) 002728-01 (Ctrl. Panel Brkt), Fluorescent Lt. Assy.— see Figure 16 48-004 (Speaker)

035745-03 036360-01 : ] (Atiact. Panel) (10” PCB Retainer) 19-9032 (Vol. Ctrl.) 035745-02 | (18” PCB Retainer) 03016902 A036965.01 (Vol. Ctrl/Brkt) (Access Panel}

00687001 (Coin Box Brkt.) | 74-2114 (Lock) A021 700-01, 02, -03 (Coin Sox) Reg./Audio I! PCB Assy.— | see Figure 20 78-24012 (Separator) 007882.02 (Tie Wrap) (Interl, Sw. Cover) 75-07017 New Coin Door— see Figure 22 (PCB Spacer)

034536-03 ot 78-9201 (Foam) (Cabinet Leg) Game PCB Assy.— see Figure 19 Power Supply Assy.— see Figure 21

009992-01 (OnlO#f Sw, Cover)

A034631-01 A034841-02 or (On/Off Switch) A035863-02 (Power Cord)

Figure 15 Cabinet-Mounted Assemblies A036230-xx c

Page 29

Missile Gommand™ / Cabaret

Figure 15 Cabinet-Mounted Assemblies Parts List

Part No. Description

A021700-01 Coin Box Assembly (for al/ the same coins) A021700-02 Coin Box Assembly (for two different coin denominations—has one separator) A021700-03 Coin Box Assembly (for three different coin denominations—has two separators) A030169-02 Volume Control & Bracket Assembly A034631-01 On/Off Switch Assembly A034841-02 Strain Relief Power Cord (domestic) OR A034863-02 Strain Relief Power Cord (German) A036083-01 14Inch Matsushita Color Monitor Assembly OR A036084-01 14-Inch Sanyo Color Monitor Assembly A036189-01 Interlock Switch & Bracket Assembly (modified for safety) A036295-01 Main Harness Assembly A036365-01 Access Panel Assembly DP-158-01 Missile Command™/Cabaret Schematic Drawings, Sheet 1 DP-158-02 Missile Command/Cabaret Schematic Drawings, Sheet 2 TM-153 Service Manual for Matsushita Color Monitor OR TM-157, Service Manual for Sanyo Color Monitor TM-158, Missile Command/Cabaret Operation, Maintenance, Service Manual 19-9032 Volume Control Potentiometer 48-004 5-Inch 8-Ohm 5-Watt High-Fidelity Speaker 70-304 18-Inch 15-Watt Cool White Fluorescent Tube 71-2114 Panel Cartridge Lock Mechanism (for access panel) 7507017 Spacer for Mounting Printed-Circuit Boards (two per screw) 78-24012 5-Inch Beaded Nylon Tie Wrap (for securing edge connector to Game PCB) 78-3201 Cabinet-Leveling Leg 002728-01 Control-Panel Mounting Bracket 006870-01 Coin Box Bracket 007882-02 Interlock Switch Cover 009992-01 On/Off Switch Cover 030249-01 Coin Box Separator 034536-03 Foam Vibration Damper 035745-02 18-Inch Plastic PCB Retainer 035745-03 10-Inch Plastic PCB Retainer 036220-01 Monitor Shield (smoke color) 036221-01 Rounded Trim Cap 036225-01 Speaker Grille 036228-01 Cardboard Bezel (for monitor) 036360-01 Attraction Panel with Graphics

Page 30

70-304

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the Specific writton permission of Atati, Inc., Sunnyvaie, CA. This drawing is only conditionally issued, and either receipt ‘ior passession thereof conters or ansters any right in, OF license to use, the subject maiter of the drawing or any design or technical intormation shawn thereon, nor any right to reproduce this drawing or any part thereo!. Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's’ written license, no right 10 reproduce this drawing Is granted or the subject matter thereo! unless by written agreement with or written permission from the corporetion,

Figure 16 Fluorescent Light Assembly A005493-01

99-11008

A036205-01

Parts List A 035835-01

79-561816P

Part No. Description

A005493-01 Fluorescent Light Harness Assembly 70-304 18" 15-Watt Cool White Fluorescent Lamp

79-561816P Wire Nut for 16- to 18-Guage Wires 99-11003 Fluorescent Lamp Starter 99-11008 Ballast Transformer 99-11009 Starter Socket 99-11011 1%" Clamp 035835-01 Y-Lead Connector

Page 31

Mini-Trak Ball Assy.— See Figure 18 759118

A036297-01

75-07054

75-9115

78-6900402

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL, Reproduction forbidden without the specific written permission of Atari, Inc., ‘Sunnyvale, CA. This drawing 's only conditionally issued, and neither receipt nor possession thereof confers or transfers any right in, or license to use, the subject matter of the drawing of any design or technicai information shown thereon, nor any right to reproduce this drawing or any part thereo! Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's writ: ten license, no rignt to reproduce this drawing is 036357-01 granted or the subject matter thereot unless by Witten agreement with or written permission from the corporation:

Figure 17 Control Panel Assembly A036364-01 B

Parts List

Part No. Description

A036297-01 Control Panel Harness Assembly 62-039 SPDT Momentary Pushbutton Switch, with Red Cap and LightEmitting Diode ~ QLNYLER. 62-041 SPDT Momentary Pushbutton Switch with Black Cap fi Rin& Cust 75-07054 Flat Nylon Washer, 0.470 inch inside diameter x 0.968 inch outside diameter x 0.075 inch thick

75-911S, #10-24 Steel Stamped Nut 78-6900402 Self-Adhesive Foam Tape, 1/8 inch thick x % inch wide x 1842 inches long 033127-01 Black Molded Switch Bushing 036357-01 Control Panel with Graphics

Page 32

A035940-01 Figure 18 Mini-Trak Ball™ Assembly A NOTICE TO ALL PERSONS RECEIVING THIS DRAWING

75-3608S (8 PLACES) 75.0468 | (4 PLACES) : 03593701 75.9448 75-1606S (5 PLACES)

(4PLACES) (4 PLACES) 75-8406 (4 PLACES) ~~ / 035935-01 7 eS

é A035220-01 Not shown for clarity: Harness Assembly, part no. A036096-01 Lubrication Label, part no. 034168-01

Page 33

Figure 18 Mini-Trak Ball™ Assembly Parts List m

Part No. Description

A035220-01 Coupler PCB Assembly A036096-01 Harness Assembly 72-1606S #6-32 x 3/8" Cross-Recessed Pan-Head Cadmium-Plated Steel Machine Screw 72-8406 #4-40 x 3/8" Hex Socket-Head Cap Alloy Steel Machine Screw 72-8516 %4-20 x 1” Hex Socket-Head Cap Alloy Steel Machine Screw 72-8808 #8-32 x 2" Hex Socket-Head Cap Alloy Steel Machine Screw 75-0148 #4 Flat Plain SAE-Standard Zinc-Plated Steel Washer 75-016S #6 Flat Plain SAE-Standard Zinc-Plated Steel Washer 75-018S #8 Flat SAE-Standard Zinc-Plated Steel Washer 75-044S #4 Zinc-Plated Steel Split Lock Washer 75-046S #6 Zinc-Plated Steel Split Lock Washer 75-048S #8 Zinc-Plated Steel Split Lock Washer 75-944S #4-40 Self-Locking Steel/Polymer Hex Nut 75-945S %4-20 Self-Locking Steel/Polymer Hex Nut 75-946S #6-32 Self-Locking Steel/Polymer Hex Nut 85-1808B #8-32 x V2" Socket Cap Flat Countersunk-Head Black-Oxide Steel Screw 034168-01 Label with Lubrication Instructions 035926-01 Base Plate 035927-01 Top Plate (Metal) 035928-01 Top Plate (Acrylic) 035929-01 Corner Post 035930-01 End Post 036931-01 Roller Shaft 035932-01 Standoff 035933-01 Adjustable Post 035934-01 Spacer 035935-01 Angle Bracket 035936-01 Mini-Trak Ball™ 035937-01 Bearing 035938-01 Encoding Wheel

Page 34

SEE DETAIL,

ol -01 03 VERSION =O3VERSION| (PROM) (PROW) ~02 —oaversion) (ROM:

ol coiez94 -o1

SPLIT PAD CONNECTIONS AS DETAILED ARE

“ey Bus! +12v BUS

2708 ENABLE Bato “aus: B3I6E ENABLE

APPLICABLE TO USE OF @3IGE'S.USE OF 2708'S

DETAIL

REQUIRE BRIDGING OF OPEN PADS AND CUTTING

TYP, 6 PL, SCALE : NONE OF CONNECTED PADS.

D Figure 19 Missile Command™ Game PCB Assembly A035467-01 thru -04

Page 35

Figure 19 Game PCB Assembly Parts List

Part No. Description , (Reference Designations and Locations in Bold)

C012294-01Audio I/O N-Channel MOS/LSI Custom Chip(P8/9)

21-101683 .068 uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (C65-68) 24-250105 1 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C76-79, 98, 100-104)

24-25010610 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor(C20, 23, 39)
24-250107100 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor(C9, 10, 46, 57, 91)
24-25022622 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor(C90)
27-250103.01 uf Ceramic-Disc 25V Radial-Lead Capacitor(C76-79)

28-101102 1000 pf Epoxy-Dipped 100V Radial-Lead Mica Capacitor (C99, 105)

29-088.-1 uf Ceramic-Disc 25V Radial-Lead Capacitor(C1-8, 13-16, 18, 19, 21, 22, 30, 38, 43-45, 47-56,

58-64, 69-75, 80-89, 92-97, 106)

31-1N91475V Type-1N914 Switching Diode(CR2)

34-2N3643, Type 2N3643 NPN Switching Transistor (Q8) 34-2N6044, Type 2N6044 NPN Darlington Transistor (Q1-3)

37-4584BType 14584 Integrated Circuit(C9, C11)
37-7400Type 7400 Integrated Circuit(C5, D8)
37-74S00Type 74S00 Integrated Circuit(A8)
37-7404Type 7404 Integrated Circuit(E6, K7)
37-74HO4Type 74HO04 Integrated Circuit(B6)
37-74S04Type 74804 Integrated Circuit(D7)
37-7407Type 7407 Integrated Circuit(N11)
37-74LS08Type 74LS08 Integrated Circuit(R2, J6, H7)
37-74S08Type 74808 Integrated Circuit(M3)
37-74LS10Type 74LS10 Integrated Circuit(E3, B5)
37-74L814Type 74LS14 Integrated Circuit(D3, J9)
37-7427Type 7427 Integrated Circuit(B7)
37-7432Type 7432 integrated Circuit(C3, R5)
37-74LS32Type 74LS32 Integrated Circuit(J7)
37-74S32Type 74832 Integrated Circuit(C4, L5, K6)
37-7442Type 7442 Integrated Circuit(N2, E8)
37-7474Type 7474 Integrated Circuit(H6, A7, E7, F7, J8, A9)
37-74S74Type 74S74 Integrated Circuit(A6, B8, C8)
37-7475Type 7475 Integrated Circuit(R7)
37-7493Type 7493 Integrated Circuit(D4)
37-74109Type 74109 Integrated Circuit(D6)
37-74125Type 74125 Integrated Circuit(R6)
37-74LS139Type 74LS139 Integrated Circuit(P2, M5)
37-74LS153Type 74LS153 Integrated Circuit(F5, H5, J5, K5, P7)
37-74153Type 74153 Integrated Circuit(F3, H3, J3, K3)
37-74LS157Type 74LS157 Integrated Circuit(H2, J2, K2, L2, M2, M7, D9)
37-74S157Type 748157 Integrated Circuit(E4)
37-74160Type 74160 Integrated Circuit(E5)
Page 36

Figure 19 Game PCB Assembly, continued Parts List

Part No. Description (Reference Designations and Locations in Bold)

37-74163Type 74163 Integrated Circuit(D5)
37-74. S163AType 74LS163A Integrated Circuit(R4)
37-74LS 166Type 74LS166 integrated Circuit(P6)
37-74175Type 74175 Integrated Circuit(6)
37-74LS175Type 74LS175 (ntegrated Circuit(C7)
37-74LS191Type 74LS191 Integrated Circuit(K8, K9)
37-74191Type 74191 Integrated Circuit(A4, B4)
37-74LS195Type 74LS195 Integrated Circuit(M6, N7)
37-74LS244Type 74LS244 Integrated Circuit(A/B1, E2, F2, P5, L9, M9, P10, B/C1, NIP3)
37-74LS251Type 74LS251 Integrated Circuit(N5)

37-74S260 Type 748260 Integrated Circuit (A5)

37-74LS273Type 74LS273 Integrated Circuit(N6, F9)

37-LM324 Type LM324 Integrated Circuit (N10) 38-MV5053 Type MV5053 Light-Emitting Diode (CR1)

62-001SPST Pushbutton Switch(83)

66-118P1T 8Station Single-Throw, Dual-Inline-Package Bit Switch (R8, R10) 79-42C24 24-Contact Medium-insertion-Force Integrated Circuit Socket (For -01 and -03 PCB Assemblies: D1, Et, Ft, H1, J/K1, K/L1, LM1, M/N1, N/P1, R1, R3; For -02 and -04 PCB Assembties: H1, J/K1, KIL1, UM4, N/P1, R1) 79-42G40 40-Contact Medium-insertion-Force Integrated Circuit Socket (C2, P8/9) 81-4302 Nylon Snap-In Fastener

90-12310.000 MHz, + .005%, Crystal(Y1)

90-6013 Microprocessor (C2)

90-7005,Random-Access Memory(47)

020670-01 Test Point 035826-01 Programmable Read-Only Memory (L6)

100017-001Random-Access Memory(F4, H4, J4, K4, L4, M4, N4, P4)

110000-102 4K Ohm, +5%, YW Resistor (R1, 2, 4, 13, 16, 21-26, 39, 60, 61, 73, 74, 85, 95, 109-122) 110000-103 10K Ohm, +5%, %W Resistor (R3, 17-20, 30-38, 60-71, 83, 84, 86-88, 93, 94, 96-100)

110000-1521.5K Ohm, +5%, 4W Resistor(R79)
110000-22022 Ohm, +5%, YW Resistor(R46, 47, 82)
110000-221220 Ohm, +5%, %4W Resistor(R72)
110000-2222.2K Ohm, +5%, %W Resistor(R76)
110000-3323.3K Ohm, +5%, %W Resistor(R56-59, 89-92)

110000-270 27 Ohm, +5%, ¥4W Resistor (R5-12, 27-29) 110000-331 330 Ohm, +5%, YW Resistor (R14, 15, 78)

110000-391390 Ohm, +5%, %W Resistor(R45, 81)
110000-471470 Ohm, +5%, v4W Resistor(R40-44, 48-55, 80)
110000-47247K Ohm, +5%, 4W Resistor(R75)
110000-6826.8K Ohm, +5%, %4W Resistor(R101-108)
110000-8228.2K Ohm, +5%, %W Resistor(R77)

122004-224 .22 uf Ceramic-Disc 25V Radial-Lead Capacitor (C24-29, 31-37, 40-42)

137002-001Type 74886 Integrated Circuit(13)
137149-001Type 74LS11 Integrated Circuit(F6, N3)

For remaining memory components and their part numbers, see list on next page.

Page 37

Figure 19 Game PCB Assembly, continued Parts List

Memory Components and Their Equivalents (Locations Shown in Bold)

01 P.C. Boards -02 P.C. Boards -03 P.C. Boards 04 P.C, Boards (mostly PROMs) (ROMs) (mostly PROMs) (ROMs)

03681201 KILA 03581202 KIL ~~ 03582201 KILI ~~ 03682202 KILI 03581301 FA 036813-02 Fi

03582301 _LIM1 03582301 UNH 035823-02 _UM1 03682302 LMI

03581601 NIP 035816-02 NIP 03582401 NIP1 035824-02 NIP1 035817-01 MINA 035817-02 MIN1

035818-01 RI 03581802 Rt 035625-01 Rt 03582502 R1 036819.01 3 03581902 R3

035808-01 Ht 03680802 Hi 03582001 Hi 03582002 Ht 03580901 D1 035809-02 Dt

036810-01 WK1 035810-02 JIK1 03682101 J/K1 03582102 JIK1 03661101 E1 03681102 E1

Page 38

3015 3LIS0dd0 NO auv NMOHS S30vaL NOTICE TO ALL PERSONS RECEIVING THIS DRAWING. CONFIDENTIAL: Regroduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally Issued, and neither receipt nor possession thereot conters or transfers any right in, or license to use, the subject matter of the drawing or any design oF technical information shown thereon, nor any right to reproduce this drawing or any part thereof. Except for manufacture by vendors of Atati, Inc. and for manufacture under the corporation's writ ten license, no right to reproduce this drawing is Granted or'the subject matter thereof unless by written agreement with oF written permission from the corporation.

Figure 20 Regulator/Audio li PCB Assembly A035435-02

Page 39

Figure 20 Regulator/Audio Il PCB Assembly Parts List

Part No. Description (Reference Designations and Locations in Bold)

12-52P7 2.7 Ohm, + 5%, 1W Resistor (R5) 16-54P0 4 Ohm, + 5%, 5W Wirewound Resistor (R25) 19-100P1015 1 Ohm, + 3%, 7W Wirewound Resistor (R24) 19-315102 1K Ohm Vertical PCB-Mounting Cermet Trimpot (R8)

24-25010610 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor(C5, 15)
24-2501081000 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor(C9, 10, 13)
24-250477470 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor(C1, 4, 12)

24-250478 4700 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C29)

24-2501081000 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor(C13)

24-250477 470 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C1, 4, 12) 24-350226 22 uf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor (C24, 31) 24-350338 3300 uf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor (C9, 10, 18, 19)

24-5001051 uf Aluminum Electrolytic Fixed Axiai-Lead 50V Capacitor(C22, 23)

27-250102 .001 uf Ceramic-Disc 35V Radial-Lead Capacitor (C2, 7, 16) 27-250103 .01 uf Geramic-Disc 25V Radial-Lead Capacitor (C5, C14) 29-088 -1 uf Ceramic-Disc 25V Radial-Lead Capacitor (C3, 11, 20, 21) 31-A14F 50V 2.5A Miniature Axial-Lead High-Current Rectifier (CR1, 4-8)

33-TIP32PNP Power Transistor, Type TIP32(Q2)
34-2N3055NPN Silicon Transistor, Type 2N3055(Q3)
37-LM3055V Linear Voltage Regulator(Qt)
37-7812+12V Voltage Regulator, Type 7812(Q8)
37-7905—5V Voltage Regulator, Type 7905(Q9)

72-1608C #6-32 x 2” Cross-Recessed Pan-Head Corrosion-Resistant Steel Machine Screw 75-F60405 #6-32 x 14" Binder-Head Nylon Screw 75-99516 #6-32 Nut/Washer Assembly

78-16008Thermally Conductive Compound(Q3)
78-6014Thermally Conductive Compound(Q2, 5, 7-9)
79-583066-Position Connector Receptacle(u6, 9)
79-§83089-Position Connector Receptacle(J7)
79-5834612-Position Connector Receptacle(J10)
79-583544-Position Connector Receptacle(J8)

020670-01 Test Point 034531-01 Heat Sink

110000-0101 Ohm, + 5%, %4W Resistor(R10, 19)
110000-10010 Ohm, + 5%, YW Resistor(R11, 20, 29, 30)

110000-101 100 Ohm, + 5%, %4W Resistor (R4, 12, 22) 110000-102 1K Ohm, + 5%, %4W Resistor (R27, 28)

110000-10310K Ohm, + 5%, %W Resistor(R13, 14)
110000-271270 Ohm, + 5%, “%4W Resistor(Ri)
110000-33033 Ohm, + 5%, YW Resistor(R3)

110000-392 3.9K Ohm, + 5%, %4W Resistor (R6)

110000-5625.6K Ohm, + 5%, %W Resistor(R32, 33)

110000-752 7.5K Ohm, + 5%, ‘4W Resistor (R7)

110001-221220 Ohm, + 5%, veW Resistor(R9, 21)

116000-220 22 Ohm, + 5%, 10W Wirewound Resistor (R31)

122004-224.22 uf Ceramic-Disc 25V Capacitor(C6, 8, 15, 17)
137151-002Type TDA2002A 8W Linear Audio Amplifier Integrated Circuit(Q5, 7)
Page 40

034482.01 79-4411006 46-2017002 034544.01 462013002

TOP VIEW 78-2708

ln oi

29-053

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the Specific written permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally’ issued, and neither receipt nor possession thereo! confers or transfers any right in, or license fo use, the subject matter of the draw: ing or any design or technical information shown thereon, hot any right fo reproduce this drawing or any part thereot Except for manufacture by vendors of Atan, Inc, and for manufacture under the corporation's written license, no tight to reproduce this drawing is granted or the subject matter thereof unless by written agreement with or written petmission from the corporation 142001.001

Z| BOTTOM VIEW ia

Figure 21 Power Supply Assembly for Color Raster-Scan Games A036099-01 A

Page 41

Figure 21 Power Supply Assembly for Color Raster-Scan Games Parts List

Part No. Description

A006555-01 Rectifier Printed Circuit Board Assembly A036098-01 Transformer and Harness Assembly (includes Shielded Power Transformer) A034629-01 AC Harness Assembly A034630-01 RFI Filter Assembly A035674-01 Voltage Plug Assembly (set of four plugs) 29-053 26,000 uf 15V Electrolytic Capacitor 46-2013002 3-Amp. 250V 3AG Slow-Blow Glass Cartridge-Type Fuse 46-2017002 7-Amp. 250V 3AG Slow-Blow Giass Cartridge-Type Fuse 78-2708 Nylon Type 6/6 Hole Bushing with 5/8” Inside Diameter x 55/64” Outside Diameter x %”" Thick 78-70501SC. 2"-Diameter Capacitor Mounting Bracket 79-15021001 2-Circuit Single-Row Terminal Block 79-3206 5-Position 3AG Fuse Block with 4” Quick-Disconnect Terminals 79-4411006 Panel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post 034544-01 Fuse Block Cover ASS 142001-001 Shielded Power Transformer Only (with isolation windings)

Page 42

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING 99-10103 CONFIDENTIAL: Reproduction forbidden without the pecilic wntten permission of Atari, Inc. Sunnyvale, CA his drawing is only conditionally’ issued, and neither receipt nor possession thereof confers or transters any 99-10086 99-10095 fight in, or license to use, the subject matter of the draw ing of any design or technical information shown thereon, nor any ight to reproduce this drawing or any part thereot. Except for manutacture by vendors of Atari Inc., and for manufacture under the corporation's written license, no right to reproduce this drawing is granted or the subject matter thereot unless by writfen agreement <a with of written permission from the corporation. ra 99-10071 a oS 99-1073

PART OF 99-10095

99-10064

COIN INLET CHUTE 99-10097 99-10101

70-11-47

99-10105

COIN MECHANISM SEE PARTS LIST (71-12x.009

99-10102 65-441C COIN RETURN; —98-10065 SWITCH WIRE CHUTE 99-10068 _/ SEE PARTS LIST (99-10075 thru 99-100 COIN SWITCH ASSY. ad PART OF 99-10047 SEE PARTS LIST 99-1008 99-10082 (99-1042 thru 75-14128, 99-10045)

Figure 22 New Coin Door 71-10xxxx

Page 43

COIN RETURN BUTTON COVER— SEE PARTS LIST (99-10055 thru 99-10059)

COIN RETURN BUTTON ASSY.— PRICE PLATE— SEE PARTS LIST SEE PARTS LIST (99-10012 thru 99-10022, {99-10070, 99-10083 99-10074 and 99-10107) thru 99-10092, and 99-10108) 72-JA1405B COIN DOOR ONLY— SEE PARTS LIST 99-10062 99-10054 (99-0009 and 10010) 72-HA1404C

PART OF 99-10074

75-5520B

99-10061 NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunayvale, CA, This drawing is only conditionally ‘ issued, and neither receipt nor possession thereof confers or transfers any right in, or license to use, 99-10066 the subject matter of the drawing or any design or technical information shown thereon, nor any right to reproduce this drawing or any part thereof. Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's writ ten license, no right to reproduce this drawing IS 7g gy 55 granted or the subject matter thereof unless by +9 written agreement with or written permission from the corporation. 72-JA1405B

99-10051

Figure 22 New Coin Door 71-10xxxx

Page 44

ao Figure 22 New Coin Door, continued Parts List Pa

Part No. Description

31-1N4002 100V Silicon Rectifier 1N4002 Diode 65-441 General-usage low-force miniature switch 70-11-47 Miniature bayonet-base incandescent lamp, type #47 71-1201ADU U.S, $1.00 coin mechanism 71-1201FCH Swiss 1 Fr coin mechanism 71-1201MG German 1 DM vanananen 71-1202MG German 2 DM coin mechanism 71-1205FB Belgian 5 Fr coin mechanism 71-1205MG German 5 DM coin mechanism 71-1210PE U.K. 10 P coin mechanism 71-1220CA Australian 20¢ coin mechanism 71-1225CU U.S. 25¢ coin mechanism 71-12100LI Italian 100 Lire coin mechanism 71-12100Yu Japanese Y100 coin mechanism 72-HA1404C #4x14" Slotted pan-head thread-rolling tri-fluted ‘“‘Taptite” cadmium-piated screw 72-JA1405B #4x5/16” Slotted pan-head thread-rolling tri-fluted “Plastite” black screw 72-9406S #4-40x3/8" Slotted truss-head steel machine screw 72-9603S #6-32x3/16" Slotted truss-head steel machine screw 75915S #14-20 Standard pattern cadmium-plated steel hex nut 75-918S #8-32 Standard pattern cadmium-plated steel hex nut 75-9445, #4-40 Polymer self-locking steel hex nut 75-9485, #8-32 Polymer self-locking steel hex nut 75-1408S, #4-40x V2" Slotted pan-head steel machine screw 75-1412S #4-40x34" Slotted pan-head steel machine screw 75-§520B #1%4-20x1%4" Round-head square-neck steel bolt with black finish , 99-10008 Switch wire retainer 99-10009 2-Mech coin door only 99-10010 3-Mech coin door only 99-10011 Inner panel 99-10012 U.S. 25¢ coin return button assembly 99-10013 U.S. $1.00 coin return button assembly 99-10014 German 1 DM coin return button assembly 99-10015 German 2 DM coin return button assembly 99-10016 German 5 DM coin return button assembly 99-10017 Belgian 5 Fr coin return button assembly 99-10018 Swiss 1 Fr coin return button assembly 99-10019 Japanese Y100 coin return bution assembly 99-10020 U.K. 10 P coin return button assembly 99-10021 Australian 20¢ coin return button assembly 99-10022 Italian 100 Lire coin return button assembly 99-10040 Goin inlet chute assembly 99-10041 Coin counter assembly 99-10042 Coin switch assembly for U.S. 25¢ and Belgian 5 Fr coins (siiver wire) 99-10043 Coin switch assembly for German 1 DM, Swiss 1 Fr, and Japanese Y100 coins (black wire) 99-10044 Coin switch assembly for U.S. $1.00, German 2 DM, and Italian 100. Lire coins (gold wire)

Page 45

Figure 22 New Coin Door, continued Parts List

Part No. Description

99-10045 Coin switch assembly for German 5 DM, U.K. 10 P, and Australian 20¢ coins (green wire) 99-10047 Lockout coil assembly 99-10048 Coin door harness assembly 99-10049 Locking arm assembly 99-10051 Coin door frame 99-10052 Coin return lever 99-10054 Coin button housing 99-10055, Coin return button cover for Japanese Y100 coin 99-10056 Coin return button cover for German 1 DM and Swiss 1 Fr coins 99-10057 Coin return button cover for U.S. 25¢ and Belgian 5 Fr coins 99-10058 Coin return button cover for U.S. $1.00, German 2 DM, and Italian 100 Lire coins 99-10059 Coin return button cover for German 5 DM, U.K. 10 P, and Australian 20¢ coins 99-10061 Coin return bezel 99-10062 Coin return button 99-10063 Right half of coin inlet chute 99-10064 Left half of coin inlet chute 99-10065 Coin return box 99-10066 Coin return cover 99-10070 U.S. 25¢ price plate 99-10071 Slam switch assembly 99-10073 Test switch decal 99-10074 Lock assembly 99-10075 Black switch wire—for German 1DM, Swiss 1Fr and Japanese Y100 coins 99-10076 Silver switch wire—for U.S. 25¢ and Belgian 5Fr coins 99-0077 Gold switch wire—for U.S. $1.00, German 2DM and Italian 100 Lire coins 99-10078 Green switch wire—for German 5DM, U.K. 10P and Australian 20¢ coins 99-10080 Miniature bayonet-base lamp socket 99-10081 Wire key holder 99-10082 Switch cover 99-10083 U.S. $1.00 price plate 99-10084 German 1 DM price plate 99-10085 German 2 DM price plate 99-10086 German 5 DM price plate 99-10087 Belgian 5 Fr price plate 99-10088 Swiss 1 Fr price plate 99-10089 Japanese Y100 price plate 99-10090 U.K. 10 P price plate 99-10091 Australian 20¢ price plate 99-10092 Italian 100 Lire price plate 99-10094 Fish paper insulation 99-10095 Toggle switch 99-10096 “U"-type fastener 99-10097 Fish paper insulation 99-10101 Coin inlet chute sub-assembly 99-10102 Switch and lockout coil bracket sub-assembly 99-10103 Inner panel with levers sub-assembly 99-10104 Anti-penny-flip bar retainer 99-10105, Anti-penny-flip bar 99-10107 U.S. 50¢ coin return button assembly 99-10108 U.S. 50¢ price plate—for two quarters

Page 46

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 47

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 48

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 49

a 1st printing

YOUR COMMENTS, PLEASE!

Your comments will assist Atari in improving the usefulness of our publications. They are an important part of preparing for revisions of manuals and parts catalogs. No postage stamp is necessary if mailed in the U.S.A.

If you have any technical questions about certain Atari or Kee Games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply:

Name Firm OU Distributor

Address. O Operator City State Zip (1 Other.

Page 50

First fold

. BUSINESS REPLY MAIL

FIRST CLASS PERMIT NO. 1004 SUNNYVALE_CA

POSTAGE WILL BE PAID BY ADDRESSEE

Atari, Inc. Attn.: Field Service/Coin-Op Division P. O. Box 427 Sunnyvale, California 94086 No Postage Necessary if mailed in the United States

Cut along this line —~*e

Second told

eBpe siyy edey :WOl4

Page 51

Seller warrants that its printed circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its television monitors (in games supplied with monitors) are free from defects in material and workmanship under normal use and service for a period of thirty

  • days from date of shipment. None of the Seller's other products or parts thereof are warranted.

If the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are returned to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
  • Such products are returned prepaid to Sellers’ plant; and
  • Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing.

In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages.

Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms of this order, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantabil-. ‘ity and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products uhder this order.

The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to yourself and others. Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety.

Atari distributors are independent, being privately owned and operated. In their judgment they may.sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible forthe quality, suitability or safety of any non-Atari part or any modification including labor which is‘pérformed by such distributor.

This document is and contains confidential trade secret information of Atari, Inc.

This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for @ any other purpose whatever, and remains the property of Atari, Inc. Neither it nor the information it contains may be reproduced, used, or disclosed to persons not haying a need to know Consistent with the purpose of the loan, without written-consent of Atari, Ino:. SERS ASEM ES SAS AS AN

Page 52

ATARI" ATARI ING 1265 BORREGAS AVENUE PO. BOX 427 SUNNYVALE, CALIFORNIA 94086 408/745-2000 © TELEX 35-7488 FS svn tonvarncion canon