Cloak & Dagger Kit TM-257 1st Printing Installation for Defender
Cloak & Dagger (rev 5) (Atari, 1983) · Installation · 22 pages · 11 sections · original scan
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
If reading through this manual does not lead to solving a certain maintenance prob-
lem, call TELEHELP® at the Atari Customer Service office in your geographical WEST and CENTRAL U.S.A
area, as shown below. WEST and CENTRAL U.S.A.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
ti 21983 by Atari, Inc All rights reserved.
No part of this publication may be reproduced by any mechanical, Photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permisssion from the publisher.
The game play, all graphic designs, this technical manual, its accompanying
schenet ie diagrams, and the display manual are protected by the U.S. Copyright
Act of! 6
This Act provides for increased penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles.
In addition, the Act provides for payment of statuatory damages of up to $250,000 in certain cases. Infringers may also have to pay costs and attorneys' fees and face an imprisonment of up to five years,
Atari will aggressively enforce its copyrights against any infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation a copy video games made by us. Anyone who purchases such copies risks forfeiting such a game.
Published by: ATARI, INC. 790 Sycamore Drive P.O. Box 906 Milpitas, California 95035
Printed in the U.S.A. 12M
CLOAK AND DAGGER Installation Instructions T™-257
Remove Part of the Harness Assembly............ Remove the Game Printed-Circuit Boards. Remove the Control Panel....... Remove the Attraction Shield. Remove the Display Shield.... Install the Display Shield........ Install the Control Panel.........0+ Install the Attraction Shield. Install. the Wood Panel for the EMI Cag Attach the EMI Cage to the Wood Mounting Panel. Install the CLOAK & DAGGER Retrofit Main Harness....... Install the Self~Test Chart......... Performa Self Test........ Apply the Labels........... Attach the Side-Panel Decals. Attach the Coin-Mechanism Panel Decal.........sseeesececeees 14 Change Your Original Schematic Set To Reflect the CLOAK & DAGGER Retrofit.....cccccccccccccccccccccncccccsssccescces 14 ODOODDDANDAUWWEE
LIST OF ILLUSTRATIONS Figure 1 Attraction Shield and Display Shield Replacement.... 4 Figure 2. Printed-Circuit Boards and Volume Control Removal.... 7 Figure 3 CLOAK & DAGGER Control Panel Installation.......... 8 Figure 4 CLOAK & DAGGER Harness and EMI Cage Installation... 10 Figure 5 CLOAK & DAGGER Decal Installation..........eeeeeee5 13
LIST OF TABLES Table 1 Retrofit Kit Contents for Defender......-.esseeeeceseeee Lb Table 2 Tools Required... .. cc cece cen een ecceeccccccccseens F
iti
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
CLOAK AND DAGGER Installation Instructions TM-257
CLOAK & DAGGER™* Installation Instructions for Defender**
INTRODUCTION
The following information includes the necessary installation instructions for changing the Defender™ game into a CLOAK & DAGGER™ game. The modifications include changing the cabinet graphics, the control panel, the attraction shield, the display shield, the game printed-circuit boards, and harness assembly. A CLOAK & DAGGER Schematic Package is provided for the game circuitry. If you have a schemtic set that was originally provided for your game, ene the power supply, sound printed-circuit board, and monitor schematics.
KIT PARTS INVENTORY
Check the contents of the CLOAK & DAGGER Retrofit Kit (A041462-01) before proceeding with the retrofit procedure. The parts included in this retrofit kit are listed in Table 1.
Table 1 Retrofit Kit Contents for Defender A041462-01
Part No. Quantity Description
| A037701-01 | 1 | Electromagnetic Interference (EMI) Cage and |
Guides Assembly—includes
| 037700-02 | 1 | EMI Cage |
| 178047-032 | 4 | PCB Guide |
| A040733-01 | 1 | EMI Shield and Dual PCB Assembly—inclides |
| A039431~01 | 1 | CLOAK & DAGGER Interconnect PCB |
| A039938-21 | 1 | CLOAK & DAGGER Slave PCB |
| A039942-21 | 1 | CLOAK & DAGGER Master PCB |
| A040404-01 | 1 | EMI Shield PCB |
| 72-1604F | 4 | #6-36 x 1/4-Inch Cross-Recessed Steel Screw |
| 034536-02 | 1 | 0.50-Inch Thick Foam Pad |
| 034536-03 | 1 | 1.12-Inch Thick Foam Pad |
continued on next page—
- A trademark of Universal City Studios, Inc. and licensed by Merchandising Corporation of America, Inc. **Trademark of Williams Electronics, Inc.
CLOAK AND DAGGER Installation Instructions TM-257
Table 1 Retrofit Kit Contents for Defender (continued) Part No. Quantity __ Descriptio
| A041463-01 | 1 | Control Panel Assembly—includes |
| A041465-01 | 1 | Control Panel and Decal Assembly |
| A040729-01 | 1 | Control Harness Assembly |
| 171021-001 | 2 | 8-Position Joystick Assembly |
| A041509-01 | 1 | Retrofit Main Harness and Component Assembly |
| A041402-01 | L | Main Harness |
| 119006-103 | 1 | 10 kQ Dual Potentiometer |
| SP-~242 | 1 | CLOAK & DAGGER Schematic Package |
| ST-242-01 | 1 | CLOAK & DAGGER Chart with Self-Test Procedure |
and Option Switch Settings
| TM-242 | 1 | CLOAK & DAGGER Operators Manual |
| 72-1816F | 4 | #8-32 x 1~Inch Long Cross-Recessed, Pan-Head |
Machine Screw (used to mount wood panel to cabinet wall)
| 75-048S | 4 | #8 Split-Lock Washer (used to mount wood panel |
to cabinet wall)
| 75-018S | 4 | #8 Flat Washer (used to mount wood panel to |
cabinet wall)
| 038086-01 | 1 | Shock Warning Label |
| 038158-03 | 1 | Product ID Label |
| 039450-01 | 1 | FCC Compliance Label |
| 041471-01 | 1 | Left Side-Panel Decal |
| 041471-02 | 1 | Right Side-Panel Decal |
| 041472-01 | 1 | Coin-Mechanism Panel Decal |
| 041473-01 | 1 | Display Shield |
| 041474-01 | 1 | Attraction Shield |
| 041476-02 | 1 | Attraction Shield Semi-Rigid Film |
| 041477-02 | 1 | Wood Mounting Panel for EMI Shield Assenbly |
| 175004-708 | 2 | #8 Flat Fiber Washer (used to mount EMI cage |
to wood 1)
| 176015-112 | 3 | #10 x 3/4-Inch Long Cross-Recessed, Pan-Head’ |
Screw (one used to mount EMI cage to wood panel; two used on control panel)
The Master, Slave, and Interconnect Printed- Circuit Boards are already installed in the EMI Cage of the retrofit kit.
CLOAK AND DAGGER Installation Instructions T™-257
TOOLS REQUIRED
The tools-listed in Table 2 (or their equivalents) are required to performa complete retrofit.
Table 2 Tools Required
| Quantity | Description | Purpose |
| 1 | Phillips-head screwdriver | Remove ami install retainers, |
attraction shield, display shield, and hamess
| 1 | Squeegee | Install decal graphics |
| 1 | X-ACTO™ blade or suitable | Install decal graphics |
substitute
RETROFIT INSTRUCTIONS
These procedures mist be performed by qualified service personnel. All interior and exterior surfaces should be clean and free of foreign material before starting this retrofit procedure.
The following procedures are arranged in a sequence recommended for performing the retrofit modification. The parts of your game that are affected by the retrofit (see Figure 1) are removed first. Then, the CLOAK & DAGGER kit parts are installed.
Unplug the game before performing the following procedures.
CLOAK AND DAGGER Installation Instructions ‘TM-257
_— Upper Attraction | ! Retainer
Attraction Shield
Display Shield Retainer
Lower Attraction Retainer
Display Shield
Figure 1 Attraction Shield and Display Shield Replacement
CLOAK AND DAGGER Installation Instructions 'T™-257
Remove Part of the Harness Assembly
10.
ll.
12.
DO NOT REMOVE the game harness wiring to the following items:
©@ Power Supply Transformer Connectors (see
Speaker Safety Interconnect Switch at Rear of Cabinet On/Off Switch Moniter AC
Unlock and remove the rear access panel.
Unplug the coin-door connector.
Remove the coin-deoor interlock switch with a Phillips-head screwdriver.
Unplug the control-panel connectors.
Unplug the sound PCB connectors. Remove ami discard the microprocessor and ROM socketed integrated circuits on the sound PCB.
Unplug the speaker connector.
Unplug two of the three power-supply base connectors. BE SURE TO LEAVE THE TRANSFORMER CONNECTOR IN PLACE (see Figure 4).
Remove the volume control from the U-shaped bracket that is located on the side of the cabinet next to the sound PCB. SAVE THE BRACKET AND SCREWS FOR THE CLOAK & DAGGER VOLUME CONTROL INSTALLATION.
Unplug the signal connector on the monitor PCB.
Unplug the connectors from the game printed-circuit boards.
Remove the white nylon harness screw-down clamps that secure the loosened harness wires. BE SURE TO SAVE THESE CLAMPS AND SCREWS FOR INSTALLING THE CLOAK & DAGGER HARNESS.
Discard the removed harness.
CLOAK AND DAGGER Installation Instructions 'TM-257
Remove the Game Printed-Circuit Boards
Use the Phillips-head screwiriver to remove the screws that secure the three game printed-circuit boards to the cabinet (see Figure 2).
Remove the Control Panel
- Reach inside the game cabinet and release the two spring-draw latches on the sides of the cabinet to the rear of the control panel.
- From the front of the game cabinet, remove the control panel from the game cabinet.
Remove the Attraction Shield
Use the Phillips-head screwdriver to remove the hardware that fastens the upper attraction shield retainer to the cabinet (see Figure 1). Remove the retainer and the attraction shield. BE SURE TO THE HARDWARE AND RETAINER FOR REASSEMBLY.
Remove the Display Shield
Use the Phillips-head screwdriver to remove the hardware that fastens the plastic retainer to the top of the game display shield (see Figure 1). Remove the retainer and display shield by pulling out on the retainer. BE SURE TO KEEP THE HARDWARE AND RETAINER FOR REASSEMBLY.
Install the Display Shield
- Slide the top of the CLOAK & DAGGER display shield into the groove of the display shield plastic retainer (see Figure 1).
- Slide the display shield (with plastic retainer attached) into the groove in the wood at the bottom or the monitor screen.
- Hold the retainer tight against the game cabinet and securely attach the top retainer to the game cabinet with the mounting hardware.
Install the Control Panel
- Position the CLOAK & DAGGER control panel on the game cabinet (see Figure 3).
- From the back of the game, fasten the two spring-draw latches at the sides of the cabinet and install the #10 x 3/4-inch pan-head screws to secure the control panel to the cabinet.
CLOAK AND DAGGER Installation Instructions ‘T™™-257
= NOTE nage | Remove ROM & microprocessor integrated circuits Sound Printed Circuit Board Volume Control ircult Boat
Figure 2 Printed-Circuit Boards and Volume Control Removal
CLOAK AND DAGGER Installation Instructions TM-257
CLOAK & DAGGER Control Panel
Figure 3 CLOAK & DAGGER Control Panel Installation
CLOAK AND DAGGER Installation Instructions TM-257
Install the Attraction Shield
1.
2.
3. Slide the CLOAK & DAGGER attraction shield into the lower attraction retainer (see Figure 1).
Slide the CLOAK & DAGGER attraction film behind the attraction shield.
Hold the upper attraction shield retainer firmly against the top of the attraction shield and attach the upper retainer to the game cabinet with the mounting hardware.
Install the Wood Panel for the EMI Cage
Mount the wood panel included in the kit to the stand-offs on the cabinet wall
Signe ar el #8-32 x l-inch screws and #8 split-lock and flat washers (see
fe 4).
Attach the EMI Cage to the Wood Mounting Panel
1.
2. Slide the EMI cage into the wooden cleats on the mounting panel
Attach the EMI cage to the wood mounting panel with the #10 x 3/4-inch screw and the two #8 flat fiber washers (see Figure 4).
If you wish to change the option-switch settings, do so at this time. Refer to the CLOAK & DAGGER Operators Manual, TM-242, for further option-switch setting information.
Install the CLOAK and DAGGER Retrofit Main Harness (see Figure 4)
All CLOAK & DAGGER retrofit harness connectors are keyed to fit properly.
Install the volume control on the U-shaped bracket removed earlier. DO NOT attach the bracket to the cabinet wall at this time.
Plug the two keyed-to-fit 44-pin edge connectors into the EMI Shield PCB on the end of the EMI cage. Attach the ground clip to the bottom of the EMI cage.
CLOAK AND DAGGER Installation Instructions T™-257
Metal Mounting Piste
CLOAK & DAGGER ‘Hamess:
EMI Shield & Game PCB Assy.
Figure 4 CLOAK & DAGGER Harness and EMI Cage Installation
CLOAK AND DAGGER Installation Instructions ‘™-257
Plug in the two keyed-to-fit power-supply base connectors. Secure the harness to the power-supply base with the white nylon adhesive-backed mount.
Plug in the three keyed-to-fit conmectors to the sound PCB located on the cabinet wall above the EMI cage. Attach the grounding clip to the meta] mounting plate behind the sound PCB.
Plug in the coin-deor comector at the coin door.
Plug in the two control-panel connectors.
Plug in the speaker connector.
Plug the monitor-signal connector into position on the chassis-mounted main PCB.
Secure the CLOAK and DAGGER harness with the white nylon screw-on clamps removed earlier. Follow a routing similar to the original game hhamess. Attach the bracket/volume control to the cabinet wall.
Install the Self-Test Chart
1.
2. Staple the CLOAK & DAGGER self-test chart on the inside of the rear access panel.
Install the rear access panel on the game cabinet.
Perform a Self Test
1. Plug the game in.
Turn on the game.
Perform the self-test procedure as described in the CLOAK & DAGGER Operators Manual, TM-242.
Apply the Labels
1. Remove the protective backing from the product identification label, the FCC compliance label, and the shock warning label included in the CLOAK & DAGGER kit.
Apply the three labels to the back of the game cabinet directly above the rear access panel.
il
CLOAK AND DAGGER Installation Instructions TM-257
Attach the Side-Panel Decals
We recommend that the following procedure be
performed by two persons. One person may have
fficulty hi andling the cabinet and the large decals.
Mix a normal dishwashing solution of approximately three quarts of water and any liquid dishwashing detergent in a shallow pan.
Tip the game cabinet sideways and gently lay it ona soft blanket.
Thoroughly clean the side of the game cabinet to ensure the removal of all dust.
Use a sponge to liberally apply the water and detergent solution over the entire side of the game cabinet.
Grasp the top edge of the appropriate decal for the side of the game cabinet. Hold the decal up off the floor and peel away the protective backing.
Gently lay the decal, sticky side down, in the center of the wet surface of the game cabinet (see Figure 5). Position the decal to ensure that the color graphics are centered on the side of the cabinet.
With the decal down and in position, use the squeegee to remove all the excess water and detergent from beneath the decal by quickly working
from the center to the outside sa7e8- Hint: If any air bubbles form,
puncture them with a pin or the tip of an X-ACIO™ blade. Rub gently with a soft cloth to disperse air.
Insert a #11 X-ACTO™ blade or suitable substitute between the T-molding and cabinet wall and, following the contour of the cabinet, cut off the excess decal. Rub the cut edges with a soft cloth to smooth down any rough edges. .
When the wrinkles are removed and the decal is free of all excess water and detergent, gently turn the game cabinet over to the opposite side. Be careful to avoid damaging the freshly applied decal.
CLOAK AND DAGGER Installation Instructions
CLOAK & DAGGER Side- Panel Decal
Figure 5 CLOAK & DAGGER Decal Installation ‘TM-257
X-ACTO™ Blade
CLOAK AND DAGGER Installation Instructions TM-257
- Repeat steps 2 through 9 for the remining decal. ll. Carefully raise the cabinet to the upright position.
- When both decals are firmly affixed, remove the protective covering.
- Use a lint-free cloth to wipe off any excess water and detergent from inside and outside of the cabinet. Allow time to dry before proceeding!
Attach the Coin-Mechanism Panel Decal
- Wet the cabinet surface surrounding the coin-door opening.
- Carefully position the lower edge of the decal across the bottom of the coin-mechanism area on the cabinet and gently smooth the decal into Position with a sponge or squeegee.
Change Your Original Schematic Set to Reflect the CLOAK & DAGGER Retrofit
A CLOAK & DAGGER Schematic Package is provided for the game circuitry. If you have a schematic set that was originally provided for your game, save the power supply, sound printed-circuit board, and monitor schematics.
workmanship under normal use and service for a period from Tarren wactactans poscra pacer ne Ifthe electronic parts supplied in this kit fail to conform to this warranty, Seller’s sole liability shall be, at its option, to repair, replace, or credit ‘for such electronic parts which are returned to Seller during said warranty provided: Seller is promptly notified in. ‘said
(a) ae writing upon discovery by Buyer that said products
- Such products are returned prepaid to Seller's plant; and Seller’s examination of said. ‘Seller's satisfaction that such al- © products discloses to leged misuse, neglect, alteration, improper repair, installation, or improper testing. Inno event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages. Except for any express warranty set forth in a written contract between Seller and. | Buyer which contract supersedes the terms herein, this in lieu of all other warranties ere eng pepe elas assumes nor authorizes any other person to assume for the. Seller tion with the sale of products by Seller.
The use of any non-Atari may void according to the terms of the warranty. ee ba your warranty, GS TOu id SUS Be ery estes wi vebigacas Ate Earnie com oreo ee oa eat order to ensure your safety. Te eee Ee Ee ee ee es ei wl may sell parts or accessories other than. | parts or accessories. cannot’ the quality, A ceay ny anion ted noma ee is performed by distributor.
PA AANUGSOOUUUOUUAUGUANONUAUUUOOOOOOOUUUOOOOUOUOUOOOOOAUO00OU00000000000000N0U0UNUOQUOOOOOOOOQONEEE, BLT FUQOUUAUUSUOUOUGUUODOOGUUOOOUNOOUOOUUOUOUUUL
MI STITT TTT TTT
VOCSGUOOUOUCOOGOAONGAONSOUANUOUCHUOOSUOUONONCOUOUOGUOOOCOUONOUOONOOOOOOGOOOOOOOOGOONGNOONEERNZ