CATHODE RAY TOMES

Williams Recap Sound & Speech

Williams Recap Sound & Speech (Williams Electronics, Inc.) · Manual · 22 pages · 18 sections · original scan

Page 1

SOUND & SPEECH BOARD

SERVICING SERIES

Y Supplied by

Vidpin Amusements

ELECTRONICS, INC. www.vidpin.com

Page 2

SOUND AND SPEECH BOARD SERVICING

Welcome to Williams Electronics Video Based servicing series. This Recap Sheet contains the most

important points covered in the accompanying video tape. This Recap Sheet covers troubleshooting of Sound Boards and Speech Modules, using a logic probe and a multimeter.

The flow charts provided at the back of this Recap Sheet give you step-by-step instructions on checking power supply voltages ... logic operation .. . audio signal flow... and how to putit all together to locate and troubleshoot Sound Board and Speech Module problems.

BASIC OPERATION

The video tape began by describing the basic operation of the Sound Board and Speech Module. Sound and speech selections are always made by pulling one or more normally high input buffer lines down to ground. The inputs are tied, through buffer amplifiers, to a Peripheral Interface Adapter, or PIA, which generates an interrupt request to the Microprocessor, or MPU. The MPU reads the input and determines that a sound or speech selection has been made.

Based on the sound selection, the digital equivalent of the sound is selected from the Sound ROM, and placed on the Data Bus.

The PIA interfaces the Sound ROM with the Digitalto-Analog or D/A Converter, IC-13, which converts the digital form of the sound into a low level analog wave form.

This low-level audio signal is then amplified by IC-1, and fed to the game speaker, producing the selected sound output.

In addition to the components just described, the Sound Board has an on-board power supply, including input fuses, a bridge rectifier, and a voltage regulator. The supply provides reference and operating power for both the Sound Board and, where used, the Speech Module. Notice the test points for the Bridge and the various supply voltages.

Other circuits of interest on the Sound Board include the Clock and reset circuits. The Clock provides a common time base for Sound Board and Speech Module operation, while the Reset circuit ensures that all MPU and PIA registers are reset to zero during power up or circuit reset.

Finally, the board also contains a Scratchpad RAM, and a BCD to DEC decoder to provide chip select signals to the Speech Module and Sound ROMs, as well as the Scratchpad RAM and the PIA.

The Speech Module is a Sound Board add-on containing four Speech ROMs, one of which, IC-6, contains the main speech program.

|n addition to the Speech ROMs, the Speech Module contains a chip, IC-1, that converts digital speech data to a staircase waveform. This chip is similar toa digital-to-analog converter, The output of IC-1 is filtered and amplified by IC-3 and IC-2.

Putting it all together, a Sound Board buffer input causes the PIA to interrupt the MPU. The MPU reads Speech Program information from IC-6 on the Speech Module. The chip select and memory location information is read, and the resulting words or parts of words are read in a digital form from the Speech ROMs.

The PIA converts the speech data on the Data Bus to aserial form, and returns it to the Speech Module, at pin 12 of the D-to-A converter, IC-1.IC-1 converts the serial digital form of the Speech Data to a staircase waveform plus a sampling frequency.

The output of the D-to-A converter is filtered by two sections of IC-3, then further amplified and mixed with electronic sounds in IC-2, then fed back to the Sound Board, where it is further amplified and fed to the game speaker.

With that background the video tape next covered what it takes to locate a particular problem in the Sound Board or Speech Module of a typical game.

DETERMINE SOURCE OF PROBLEM

The first thing to determine is whether the problem is in the Sound Board or Speech Module — or whether it is really in the game itself. To find out, first run the game self-diagnostic program, selecting that part of the program which tests for sound and speech outputs.

Page 3

eee When you run the sound portion of the game diagnostics, you'll hear the appropriate sound effects.

It's important to know what to listen for in the selftest. Each game instruction booklet contains a listing of the sounds you'll hear at each step of the self-test.

As you listen to the self-test, make a note of any missing or incorrect sounds.

If there are any missing or incorrect sounds, you should refer to the flow charts at the end of this Recap Sheet to localize the component fault. This first flow chart, labeled “SOUND BOARD / SPEECH MODULE FLOW CHART #1” shows you how to determine whether the fault is in the Sound Board, the Speech Module, or in one of the other game boards.

For example, if the test produces the correct electronic sounds, but no Speech sounds, Flow Chart #1 refers you to Flow Chart #2, which shows you how to locate faults in the Speech Module. Other parts of Flow Chart #1 help you spot faults in the game, faults in the Sound Board Input Buffer Circuits, as well as audio and digital faults in both old and new Sound Boards.

The video tape next followed a technician as he checked out a game which produced no sounds or speech at all.

REPLACE MAIN CONNECTOR

Since the problem could be in the main game, one of the first steps is to pull and then replace the main connector between the game and the Sound Board. If the problem is in the game, this usually produces some type of sound as the stuck input lines are disconnected and re-connected.

If no sounds are produced as the connector is pulled and replaced, the connector is pulled again and left off, and the Sound Board Self-Test switch, SW-1, is pressed to start the board self-test routine.

The self-test routine bypasses the buffer inputs of the Sound Board. If sounds are produced during this test — but not earlier — then a faulty input buffer circuit should be suspected.

CHECK POWER SUPPLY INPUTS AND OUTPUTS

If no sounds are produced during the Sound Board Self-Test, then the next check is at the power supply inputs and outputs using the schematic found in the schematic manual.

If the power is OK, then the next step is to pull the MPU and Sound ROM and replace them with known good IC's.

If replacing the MPU and Sound ROM doesn’t cure the problem, then the next step is to confirm that the audio amplifier is OK. To do this, find Jumper W-15 on the sound board and touch it with your finger. A good audio amplifier circuit will produce a click and a low humming sound.

CHECK AUDIO CIRCUIT

Checkout of the audio circuit is the last decision point on the first flow chart. If the audio amplifier circuit checks out OK, then the problem must be a digital fault. In the case of a digital problem, continue with the correct flow chart, either five or six, for the type of board being tested.

TROUBLESHOOTING FLOW CHARTS

Troubleshooting flow charts for each section of the Sound/Speech boards are included at the end of this Recap Sheet.

In each flow chart, actions you should take are enclosed in a box. Decisions to be made, based on your tests, are enclosed in a diamond, and the conclusions you should reach, based on your tests and decisions, are enclosed in circles or “bubbles.”

In addition, you should have the correct schematics for the game being serviced, as well as component level troubleshooting manuals, where these are available.

Instruments you will need as you use the Flow charts include an accurate multimeter and a three-state logic probe.

This concludes the video tape recap introducing you to the Flow Charts you will need to troubleshoot Sound Boards and Speech Modules.

Page 4

© TIPS ON USING THE FLOW CHARTS a SER

GENERAL INFORMATION e Diamonds are decisions you must make, based on the results of a test. For example, once you have pulled and replaced a connector, you must decide whether that action has, or has not, produced sounds. Such a decision would look like this: Flow charts can either be helpful or confusing, depending on how you use them.

You'll get the most out of the Sound Board/Speech Module flow charts if you will:

e Start by becoming familiar with the basic flow of control, address and data signals through the Sound Board and Speech Module. It isn’t necessary for you to understand the fine points of the programming, but you must understand the general way in which these boards operate. The video tape, the recap sheet, and the circuit schematics are the best references here.

e Use the flow charts in the order in which they are presented. Always start with Flow Chart #1, and go through the steps in the order they appear on the flow charts. Each action and decision is necessary in order for the next action or decision to make sense. Taking shortcuts seldom saves time.

e Use the recommended test instruments. A reliable multimeter, a three-state logic probe and some means of checking an audio path are essential. A list of recommended tools is given at the end of this section.

FLOW CHART SYMBOLS

The symbols used in the troubleshooting flow charts

@ Rectangles describe some type of action you must take. Usually it is some type of test. For example, if a diagnostic step requires that you pull and replace a connector, it might look like this:

Pull/Replace 10-P3 Sounds and/or Speech Produced? Yes

e Large circles or “bubbles” — always enclose some kind of conclusion, based on the actions and decisions to that point. For example, if pulling and replacing a plug (in this case, 10-P3) produced a game sound, you would conclude:

@ Small circles or “connectors” are used to connect one part of a flow chart with another, distant, part. Usually, connectors are used to indicate that you should skip some part of the flow chart, or that you should turn to the next page. For example, if you will look at Flow Chart #1, you will see a connector under the decision “Sounds only-Missing or Incorrect Speech?’’. In this case, the connector means that you should go to a later part of the flow chart.

Sounds Only*— Missing or Incorrect Speech?

Page 5

Vs —_—-

At the bottom of the page, you will see an-

other connector 2 which directs you to con- ))

tinue with the flow chart on the next page.

e An oval shape is always used to indicate the end of a particular line of testing ina flow chart. For example, if your first tests of a game included correct operation of the game sound diagnostics, there would be no further need to check for problems in the sound board.

TEST INSTRUMENTS

You must have a reliable multimeter and a threestate logic probe to check out Sound Boards and Speech Modules in the field. The only alternative would be a ‘scope fast enough to see the timings.

Page 6

Locate SOUND BOARD/SPEECH MODULE FLOW Sound Bd/ CHART #1 Speech Mod / Game Page 1 of 2 Fault

Run Main (All sounds, speech produced correctly, per game Game instructions.) Diagnostics

Main Game Diagnostics Runs OK (No #)

Sounds Only — Missing or Incorrect Speech Some Sounds, and/or (Flow Chart #2)

Pull/Replace 10P3

Sounds (See game instructions, other tapes and recap and/or Speech sheets, this series.)

Run Speech (To run Sound Board Self Diagnostics, depress Board Self SW-1 on board.) Diagnostics

Speech Bd Diagnostics Run OK (Flow Chart #3, Old Boards, Flow Chart #4, New Boards.)

Check Power Supply Input Voltage (See board schematic.)

Check Power Supply Output Voltages

Replace MPO Output Voltages and Sound Rom OK Per Game

Page 7

eee

Run Sound Board Self Diagnostics

Speech Bd Self Diagnostics Run OK

Hum/Click Test Audio Output Circuit (Note 2)

Audio Output Hums Clicks OK Digital Fault

Notes:

  • Some games include a diagnostic chart for quick location of sound/speech board faults according to missing or incorrect sounds picked up on the main game and/or Sound Board diagnostic programs. Be sure to review the game instructions to locate this information.
  • To hum/click test an old sound board, pull connector 10-P4, and touch pin 1 of jack 10-J4. For new boards, locate and touch jumper wire W-15. Game Diagnostics SOUND BOARD/SPEECH MODULE FLOW CHART #1

Page 2 of 2

Main

(Flow Chart #5, Old Boards; Flow Chart #6, New Boards.)

(Flow Chart #7, Old Boards; Flow Chart #8, New Boards.)

In either case, you should hear a click, followed by a low hum. As an alternative, a source of AC test voltage can be obtained on a pin game by connecting any large resistor (100K ohm is a good value) to a test lead, and use this combination to jumper between either side of the power supply 12 VAC input and the points described earlier (J4, pin 1, or W-15). For the video games, it is necessary to jumper from the main power supply to get low voltage AC, since DC is normally supplied to the Sound Board Power supply.

[= |

Page 8

—— SS Sl

Locate INPUT BUFFER CIRCUITS (OLD BOARDS)

Input FLOW CHART #3 Buffer Circuit Page 1 of 1 Fault, Pull 10J3 (Verify Power) (Note 1)

Check Output of Input Buffer Amps

Buffer Check Ic 4

Amp Outputs IC 4 Output Low High Output

Possible Amp Fault

High Amp Yes 4:Micts

Input is Low

Repair, Retest Per Main Game Diagnostics Short Any Input Line to Ground

IC 10 Pin 38 (RQ) Pulses Low Notes:

  • Ifsound or speech is heard when the connector is pulled and replaced, then the problem is in the main game speech select (i.e. driver solenoids on the pin games, ROM Board on the video games). If no sound is heard, pull the connector and leave it off, then verify the power supply voltages if you have not already done so. Replace IC 10 Retest
Page 9

a

Locate Input Buffer Circuit Fault

Pull 10J3 (Verify Power)

Check Output of Input Buffer Amps (Mueaamemeedaa)

Amp Output OK

Suspected Faulty Amp Input is Low 2 Buffer Amp Fault

Pull-Up Resistor

Notes:

  • If sound or speech is heard when the connector is pulled and replaced, then the problem is in the main game speech select (i.e. driver solenoids on the pin games, ROM board in the video games.) If no sound is heard, pull the connector and leave it off, then verify the power supply voltages if you have not already done so.

INPUT BUFFER CIRCUITS (NEW BOARDS) 6

FLOW CHART #4

Page 1 of 2

(IC5-2, 4, 6, 10, 12, 1 high

IC 7-4 High and IC 6-4 Low

IC-7 Pin 4 is Low

Replace Part Retest, Using Main Game DX

a

Page 10

INPUT PUFFER CIRCUITS (NEW BOARDS) FLOW CHART #4

Page 2 of 2

Short Any Input Line (Low Pulse @ IC3, Pin 37, 38) to Ground Check IRQ

IC3 Pins 37, 38 Pulse

Replace IC-3 Retest

Page 11

a rrrrrrnnnrnnnnnnnnnEEnEEEEEEEnmen! DIGITAL FAULT DIAGNOSIS Locate Sound (OLD BOARDS)

Board FLOW CHART #5

Digital Fault Page 1 of 4 (Note 1)

(AUDIO FAULT DIAGNOSIS (OLD BOARDS) (Depress Sw-1) FLOW CHART #7 Run Sound Board Self Diagnostic (On pages 3 and 4, this chart.)

Self Test Runs OK (Located Fault per Flow Chart #3)

Check for High @ MPU Pin 36 (Reset)

Pin 36 Check for MPU (IC 1) is High @ MPU High (Note.2) Pin 6 (NMI)

Check for Pin'6 Pulsing @ MPU (IC 1) is High

Debounce' Circuit Fault

Repair Fault Retest Notes:

  • Assumes that audio output amp has been click/ hum tested OK, that power is known good, and that MPU and Sound ROM have been replaced with known good IC’s.
  • Allow for short warmup. MPU Pin 2 (@2 Clock)

Pin 37 IC 1 Pulsing

Page 12

® ——————— ee DIGITAL FAULT DIAGNOSIS (OLD BOARDS) FLOW CHART #5

Page 2 of 4

Check for Pulsing @ MPU Pin 5 (VMA)

Pin 5 Check for of MPU (IC-1) High or (R/W Signal — See Note 3) Pulsing at MPU, Pin 34 (R/W)

IC 1 Pin 34 High Power, Remove or Pulsing ROM, Turn On

Check for Pulsing @ Address Lines

Address Lines Pulsing

IC 2, 3, 5 or Cont. LN Fault

Fault in Address LN Chip Repair, Retest

(Chips on Address Line are IC 2, 3 and 5)

Notes:

  • RIWis high with no sound inputs, but pulses with an input, when SW-1 is depressed, and on Self- Test running.
Page 13

SS DIGITAL FAULT DIAGNOSIS (OLD BOARDS) FLOW CHART #5

Turn Off Power Page 3 of 4 Replaces ROM - Restore Power

Check for Pulsing Data AE Check IC 5 IC5 Yes

@ MPU Lines Pulsing for Pulsing Pins 3&4

Data Lines @ Pins 3&4 Pulsing

(IC’s on Data BUS Replace are IC 2, IC 3) 1 Chip, Retest

AUDIO FAULT DIAGNOSIS (OLD BOARDS) FLOW CHART #7

Page 1 of 2

IC6 Audio. Inputs Pulsing @ C-31 Input Check IC-6 Inputs, Outputs!

Short Across Q-3

Audio @ C-31 Input

Repair, Retest

Page 14

DIGITAL FAULT DIAGNOSIS (OLD BOARDS) FLOWCHART #5

Page 4 of 4

AUDIO FAULT DIAGNOSIS (OLD BOARDS) FLOW CHART #7

Check for Page 2 of 2 Audio @ Pin 1, IC 10

Audio @ Pin 1, IC 10 Audio @ Pin 4, IC 10 Audio @ Speakers

Wiring or Vol. Cont. Fault.

Repair, Retest

Page 15

a rrrrErnEEEIEnEEDEEEIEEEEEEEEEEEEEEmnmeemmemmemmenemenst DIGITAL FAULT DIAGNOSIS (NEW BOARDS) t ) FLOW CHART #6 Locate Sound Board Digital Fault Page 1 of 5

h Board (AUDIO FAULT DIAGNOSIS Install W-1 (NEW BOARDS) FLOW CHART #8) Run Sound Board Self- Test (Note 1) (On pages 4 and 5, this chart.)

Self-Test Speech

OK Per Note 1 Board Fault

Check for High @ MPU Pin 36 (Reset)

Pin 36 Check for High " IC 9, High @ MPU, Pin 6 (Note 3) (NMI)

Y Check for Pin 6 es Pulsing @ IC 9, High MPU Pin 37 (Clock)

Pin 37 IC 9, Pulsing

Notes:

  • Sounds produced per game chart, with electronic sounds substituted for speech at points where speech is normally synthesized. (Good board should make this change.)
  • This flow chart assumes a known good MPU and Speech ROM, audio click tested, and known good power supply voltages.
  • Allow short time for warmup.
Page 16

—KWKe_arererrr— SSS DIGITAL FAULT DIAGNOSIS (NEW BOARDS) FLOW CHART #6

Page 2 of 5 Check for Pulsing @ MPU Pin 5 (VMA)

Check for High or Pulsing @ MPU Pin 34 (R/W) (Note 4) Pin 5, IC 9, High or Pulsing

Turn Off Power, Ic 9 Pin 34, High Remove Sound or Pulsing ROM, Restore

Check for Pulsing @AII MPU Address Lines (A 0-A 15)

Address Lines Pulsing

Repair, Retest

(Chips on Address Line Are IC 2, IC 3, IC 10, IC 11)

Notes:

  • R/W is high with no sound select inputs, but pulses low with an input, when depressing SW-1, and when Self-test is running.
Page 17

EEUU EEE EEE DIGITAL FAULT DIAGNOSIS (NEW BOARDS) FLOW CHART #6

Page 3 of 5

Turn Off Power, Replace ROM, Restore Power

Check for Pulsing @ MPU Data Lines Yes (eitealew Inputs, Outputs Per Table 1 Ic2 OK Per Table Data Lines Pulsing

Fault in Data Bus IC (IC’S on Data Bus are IC 10, 11 and 12)

Repair Retest

TABLE 1

IC 2 (BCD/DEC Decoder) Inputs/Outputs

Should Be If pins are not as they should be: Check/Repair/Replace

12 Pulsing Check IC3-12, 13 input, Pin 11 output; lift connections as required to determine fault, then repair or replace, retest.

} Putsing | Replace IC2

i)

Page 18

DIGITAL FAULT DIAGNOSIS (NEW BOARDS) FLOW CHART #6

Page 4 of 5

Check Inputs,

fomancxedieked (*Those Inputs Not Previously Checked) 1C4,1C 10,1C11

RCS Check Input Inputs Outputs of IC 13 Inputs OK OK (A1-A8) Pulsing

Repair, Retest

AUDIO FAULT DIAGNOSIS (NEW BOARDS)

FLOW CHART #8

Page 1 of 2

Check for = Audio Audio @ - Output, Either Q 2 Side of @ W-15 Side Side of C-29, A of C-29 Using PST-2 “3})

Jumper Q-2 Emitter to Collector

Audio @ Q 2 Side of C-29

Repair, Retest

Page 19

DIGITAL FAULT DIAGNOSIS i

(NEW BOARDS) FLOW CHART #6

Page 5 of 5

AUDIO FAULT DIAGNOSIS (NEW BOARDS) FLOW CHART #8

Page 2 of 2

Check for Audio at IC 1-4 Audio @ Speaker

Repair, Retest

0)

Page 20

[one SPEECH BOARD FLOW CHART #2

Page 1 of 3

Connect Sound Board/Speech Module, Position W-1 “Out”

Run Sound Board Self Diagnostics

No Speech Speech Per at All Speech Game Chart eapeeg in Mod Self Test OK

Replace Speech ROMs Per Game Chart

Retest Per ®

NOTES:

1, Depress SW-1 to start self-test; turn off game to stop self test.

  • Consult game chart for speech ROM location of missing speech sounds.
  • Replace Speech ROMs one at atime; when problem clears, retest failed ROM to confirm fault.
  • Set balance control at mid-point (you may have to try various settings of the R-8 control to achieve balance on an operating game.)
Page 21

Neen en rEEnnnrnEEEEEnEEEErEESnEEEEEE SPEECH BOARD FLOW CHART #2 as Page 2 of 3

Silent Int. Between Each Selection

Pulsing Sound Board Pulses @IC 1 (Speech) Low Each Speech Pins 9 & 12

Speech & Sampling Signal @ IC 3, Pin2 Speech Mod @ (Speech Bd Fault

Ic3 Speech Replace Speech (Speech) @IC 3, Pin 7

ROMs, Retest Fault (Speech Mod)

Per @

Replacement Ic 2 Speech of Speech ROMs (Speech) @IC 2, Pin7 Cures Fault Fault (Note 4)

Run Main Game Diagnostics

Replace IC Retest Per ® ®

Page 22

SPEECH BOARD FLOW CHART

Page 3 of 3

Speech @ C-29 on Sound Board

Speech @ J4-2, R-12

Speech @ IC 1, Pin 4, Sound Board

Speech @ Speaker Game Speaker Fault

Repair/Replace Retest Per