CATHODE RAY TOMES

Mortal Kombat 3 Kit (16-44039-101 Mar 1995)

Mortal Kombat 3 (rev 2.1) (Midway, 1994) · Document · 42 pages · 25 sections · original scan

Page 1

MARCH 1995 & MIDWAY 16-44039-101

OPERATION MANUAL

Operation & Adjustments * Testing & Problem Diagnosis

Parts Information ¢ Wiring Diagrams

Page 2

MORTAL_KOMBAT

KIT

INSTRUCTIONS

Insert Coin(s).

In a two player game, the loser pays and the winner stays.

Press the Punch and Kick buttons to attack an opponent.

Press the Run button to make your on-screen character run.

Use the joystick to make the on-screen character jump, duck, move left, and move right.

Use different joystick and button combinations to discover secret moves.

Page 3

MORTAL_KOMBAT

KIT

information current at time of release.

MIDWAY Manufacturing Company reserves the rights to make modifications and improvements to its products. The specifications and parts identified in this manual are subject to change without notice.

Page 4

TABLE OF CONTENTS

Section One - Operation CHOVNYHHHDAODOR Safety Notices.. FCC Notice Conversion Procedure. Inspection and Parts List. CPU/Sound Board Assembly. Converting a Typical Video Game Cabinet. Cabinet Modifications....... Control Panel Modifications. Suggested Control Panel Template Layout. Suggested Control Panel Layout and Sticker Location: Upgrading a Mortal Kombat 2 to a Mortal Kombat 3. Install the PC Board Into a JAMMA Cabinet. Install the PC Board Into a Non-JAMMA Cabin Game Features. Starting-up.. WTSaRRGNNZLLSSSS CPU and Sound Board Test. Monitor Patterns and Burn-in Test. Coin Bookkeeping. Game Audits... Game Adjustments. Standard Pricing Table.

Utilities..... Hardware Info.. Volume Adjust. 1-24 Troubleshooting.....

Section Two - Cabinet Wiring JAMMA Chart. Interboard Wirin Cabinet Wiring Diagrar Coin Switch and Meter Wiring.

© Copyright 1995 MIDWAY Manufacturing Company

DYNAMO HS-5 IS A TRADEMARK OF DYNAMO CORPORATION.

Page 5

MORTAL_KOMBAT

KIT

SECTION

ONE

OPERATION

Page 6

SAFETY NOTICES The following safety instructions apply to all kit operators and service personnel. Specific warnings and cautions will be found throughout this manual where they apply. We recommend that you read this page before preparing your kit for play.

JN CAUTION

SALVAGED PARTS. Parts salvaged from old games are required to complete your kit. These salvaged parts must operate perfectly: otherwise, the converted game cannot perform properly or safety. Always repair circuit board malfunctions and cabinet damage before conversion is attempted.

POWER SUPPLY. Be sure the power supply from your old game is capable of +5Vdc at 5A, -5Vdce at 1A, and +12Vdc at 2A. These operating voltages are necessary for the kit. Your power supply must be FCC approved.

MONITOR. This kit is not intended for use with X-Y monitor. Suitable monitors have horizontally mounted CRTs and raster electronics with inputs for red, green, and blue video, as well as COMPOSITE NEGATIVE SYNC inputs.

COIN MECHANISMS. Be sure to clean and lubricate your old coin mechanisms. Servicing them is crucial to your game's earning potential and operation.

COIN METERS. Coin meters are not provided with this kit. Wiring information is provided as a convenience to the operator.

DISCONNECT POWER DURING INSTALLATION OR REPAIRS. To avoid electrical shock, disconnect the game from the AC power source.

!! ATTENTION !!

PROPERLY ATTACH ALL CONNECTORS. Be sure that the connectors on each printed circuit board (PCB) are properly connected. If they do not slip on easily, do not force them. A reversed connector may damage your game and void the warranty. All connectors are keyed to fit specific pins on each board.

Page 7

NOTICE - FCC WARNING STICKER THIS KIT WAS TESTED IN A MIDWAY UNIVERSAL VIDEO CABINET AND_A DYNAMO HS-5 CABINET, AND FOUND TO COMPLY WITH FCC PART 15 CLASS

AREQUIREMENTS.IFINSTALLEDINAMIDWAYUNIVERSAL VIDEO

CABINET, OR A DYNAMO HS-5 CABINET, THE FCC STICKER (16-9306) SUPPLIED IS TO BE PLACED ON THE REAR OF THE CABINET.

. INSTALLATIONOF THISKIT INTOANY OTHERPRODUCTDOESNOT
GUARANTY COMPLIANCEWITH THEFCCREQUIREMENTS.YOUARE

SOLELY RESPONSIBLE, AND MIDWAY WILL HAVE NO RESPONSIBILITY, FOR FCC COMPLIANCE FOR INSTALLATIONS IN OTHER PRODUCTS. THE FCC

WARNINGSTICKERSUPPLIEDSHOULDNOTBEINSTALLEDONTHE

CONVERTED PRODUCT UNTIL FCC COMPLIANCE IS VERIFIED.

CONVERSION PROCEDURE

INSPECTION Unpack the materials from the carton and inspected for obvious signs of damage. Use this checklist to be sure the kit is complete.

[ [

l if if

Part NumberItemQuantity
A-18968-40039CPU/Sound board assembly1
H-18158main JAMMA cable1
H-19961control panel cable1
H-20242Speaker Extension Cable1 (Use only when converting MK2 to MK3)
03-8338-11/4" PCB mounting spacers8
16-9306FCC Warning sticker1
16-9922Epilepsy Warning label1
16-10044Template1
20-9687-1red push-buttons4
20-9687-2white push-buttons4
20-9687-3blue push-buttons4
20-9687-5yellow push-buttons2
20-9978-18-way joystick2
31-1789clear overlay1
31-2315screened overlay1
31-2316-1screened marquee1
31-2319side panel decal2
31-2320decal set1

4108-01092-10B torx head tamper resistant screws 10 (to attach clear overlay to control panel)

4308-01123-24B8-32 x 1-1/2 bolts8 (to attach joysticks to control panel)
4408-01128-008-32 nuts8 (to attach joysticks to control panel)
4700-00090-00B156 x .375 x .030 flatwashers10 (to attach clear overlay to control pane!)
5556-13956-00Ferrite Bead1

FBI label 1

DYNAMO HS-5 IS A TRADEMARK OF DYNAMO CORPORATION.

Page 8

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 9

CPU/Sound Board Assembly A-18968-40039

DesignationPart NumberDescription
Bi5880-11056-00Battery, 3V Lithium
U57A-20093Sound PLD Assy
U35A-20095FPGA Assy
U45A-20096FPGA Assy
U47A-20097FPGA Assy
U2A-5343-40039-02EPROM Assy, Music/Speech
U3A-5343-40039-03EPROM Assy, Music/Speech
U4A-5343-40039-04EPROM Assy, Music/Speech
USA-5343-40039-05EPROM Assy, Music/Speech
U133A-5343-40039-06EPROM Assy, Image
U132A-5343-40039-07EPROM Assy, Image
U131A-5343-40039-08EPROM Assy, Image
U130A-5343-40039-09EPROM Assy, Image
U129A-5343-40039-10EPROM Assy, image
U128A-5343-40039-11EPROM Assy, image
U127A-5343-40039-12EPROM Assy, Image
U126A-5343-40039-13EPROM Assy, Image
U125A-5343-40039-14EPROM Assy, Image
U124A-5343-40039-15,EPROM Assy, Image
U123A-5343-40039-16EPROM Assy, Image
U122A-5343-40039-17EPROM Assy, Image
U121A-5343-40039-18EPROM Assy, Image
U120A-5343-40039-19EPROM Assy, Image
u119A-5343-40039-20EPROM Assy, Image
U118A-5343-40039-21EPROM Assy, Image
U54A-5343-40039-22EPROM Assy, Program
U63A-5343-40039-23EPROM Assy, Program
U117A-5343-40039-24EPROM Assy, Program
U116A-5343-40039-25EPROM Assy, Program
U115A-5343-40039-26EPROM Assy, Program
U114A-5343-40039-27EPROM Assy, Program
P35791-12461-05Header, 5-pin
P95791-12461-07Header, 7-pin
P105791-12461-10Header, 10-pin
P8,P11,P125791-12461-15Header, 15-pin

1-5

Page 10

CONVERTING A TYPICAL VIDEO GAME CABINET

Recommended tools and supplies [ ] black semi-gloss paint [ ] electric dri black electrical tape surplus assorted screws [ ] electric screwdriver wire cutters [ ] grease pencil or marker soldering iron and solder [ ] hex driver razor knife [ ] 180 grit sandpaper or electric sander

CABINET MODIFICATIONS

1. Repaint the cabinet with black semi-gloss paint (games with wood grain sides: remove the old decal and artwork, and clean the glue residue before painting). Allow the paint to dry.

Pencil a line roughly at the top of the old graphic. Lightly moisten the cabinet with soapy water. Apply the decal starting at the top and working down. After the decal is in place, smooth it down, taking care to squeeze out air bubbles. If you miss an air bubble, pop it with a razor knife or a pin and burnish it down. Allow 12 hours for the adhesive in the decal to set. Remove the masking.

Remove the marquee from the game cabinet and install the MORTAL KOMBAT 3 marquee in its place.

Place the Epilepsy Warning label on the front of the monitor bezel. Be sure that in does not obstruct the CRT screen, but is in full view of the players.

CONTROL PANEL MODIFICATIONS

Remove the control panel buttons and joysticks and remove the old vinyl covering and artwork.

Use the control panel template to help you design the control panel. Refer to page 1-7 for suggested template layout. The template is separate from the manual: part number 16-10044.

Drill holes, as needed, for the joysticks and the control panel buttons. Plug previous holes with wood blocks, putty, cardboard, or epoxy. File the new holes smooth. Note: If converting from a MORTAL KOMBAT 2 cabinet, you only need to drill a hole for the Run button. There is one Run button per player for a total of two buttons. Holes for the other buttons and the joysticks are already in place.

Carefully remove the backing on the vinyl control panel overlay. Place the overlay on the top of the contro! panel. Prevent air bubbles from getting under the overlay.

After the overlay is secure, use a razor knife to cut holes for the control panel buttons and joysticks.

Position the stickers next to the appropriate hole locations. Refer to page 1-7 for suggested control panel button and joystick locations.

Being careful not to displace the stickers, place the overlay on the control panel. Use the torx head tamper resistant screws and the flat washers to attach the clear overlay to the control panel. Once the clear overlay is securely in place, cut holes for the joysticks and control panel buttons.

Page 11
  • Remove the switch from the push-button by pulling the large prong away from the switch, then pull the switch off of the housing. Unscrew the nut from the housing. Open the control panel. Slide the push-buttons through the control panel from the front. Screw the nut onto the switch housing from the back of the panel. Snap the switch back onto the housing.
  • To install the joysticks, first remove the “E"-ring and slide the shaft and the plastic ring off the joystick base. Be sure that the bushings remain in the base. Use the 8-32 bolts and the 8-32 nuts to attach the base to the underside of the control panel. Slide the plastic ring around the shaft so that the rough side is next to the shaft handle. Slide the shaft through the control panel and base. Replace the "E"-ring.

{Hour veceno |[ se frouelan| \/ate7 [a [ve oo 16-1086

SUGGESTED CONTROL PANEL TEMPLATE LAYOUT

‘START SAR

sume wume

HicH HIGH hich Hick

PUNCH Kick PUNCH Kick

RUN puck r Low puck Low Low

©) PUNCH ick (©) PUNCH ck

SUGGESTED CONTROL PANEL LAYOUT AND STICKER LOCATIONS FOR A TYPICAL VIDEO GAME CONTROL PANEL.

1-7

Page 12

UPGRADING A MORTAL KOMBAT 2 TO A MORTAL KOMBAT 3

1. Remove the MORTAL KOMBAT 2 CPU and Sound board. Using 1/4" spacers and surplus screws, secure the MORTAL KOMBAT 3 CPU/Sound board to the rack.

Pull the JAMMA cable out of the two cable clamps on the top of the rack. This should give enough length to plug the JAMMA cable into the MORTAL KOMBAT 3 CPU/Sound board.

Find the speaker break-out in the JAMMA cable. Unplug the Speaker Break-out cable from the Speaker Cabinet cable. Plug one end of the Speaker Extension cable into the Speaker Break-out cable and the other end into the Speaker Cabinet cable.

The only difference between the Control Panel cables on MORTAL KOMBAT 2 and MORTAL KOMBAT 3 is the wiring for the player 1 and player 2 Run buttons.

Locate the control panel cable connector with blue-'color stripe’ wires. To connect the player 1 Run button, route a wire from the push-button switch, on the control panel, to pin 4 of the connector. For the player 2 Run button, route a wire from the push-button switch, on the control, panel to pin 9 of the connector. Extend the ground wire to the other side of both of the push-button switches.

If the original FBI Warning Label, for some reason, is no longer inside the cabinet, place the FBI

Warning Label included in this kit next to the CPU/Sound board. Be sure the label is completely visible.

INSTALL THE PC BOARD INTO A JAMMA CABINET

1. Replace the existing CPU board and sound board with the MORTAL KOMBAT 3 CPU/Sound board. Use the 1/4" PCB mounting spacers and surplus screws to secure the CPU/Sound board to the electronic rack, or to the inside wall of the cabinet.

If you choose to use the JAMMA cable provided with the kit, disconnect your old JAMMA cable from the speaker, power supply, control panel switches, (which may already be disconnected), and coin door. Remove the cable from the game. Leave your power chassis as is. Note: /f you choose to use your own JAMMA cable, check the JAMMA chart to be sure your cable is compatible.

AN CAUTION

Properly insulate any unused wires within the JAMMA cable, especially gray, gray-green, and grayyellow wires. This is a fully wired JAMMA cable. Many of the wires will not be used for this kit. These wires have been installed so that you can use this cable for future kits.

Connect the JAMMA cable to the CPU/Sound board. Use the Cabinet Wiring Diagram for reference and solder the correct JAMMA cable wires to the speaker. Then, connect the wires to the coin door, power supply and the control panel. Player 1 has white-'color stripe’ wires, except for the Start button, which has a solid white wire. Player 2 has violet-color stripe’ wires. Use the Cabinet Wiring Diagram in section two, or the Control Panel Wire Color list on the inside back cover for reference when connecting these wires to the player 1 and 2 control panel switches.

Connect the Auxiliary cable to P12 of the CPU/Sound board. Use the Cabinet Wiring Diagram in section two, or the Control Panel Wire Color list on the inside back cover for reference when connecting these wires to the Low Punch and Low Kick switches.

Page 13
  • Place the FBI Warning Label next to the CPU/Sound board. Be sure the label is completely visible.
  • Install the ferrite bead: If the kit is being installed into a Dynamo HS-5 cabinet, locate the 9-pin connector at the rear of the slide out rack assembly, going to the coin door. Unplug the connector. Open the ferrite bead and loop the cable through the ferrite bead twice. Close the ferrite bead and plug the connector back in.

If the kit is being installed into a MIDWAY Universal Cabinet, locate the player 3 connector going to the CPU/Sound board. Unplug the connector from the PC board. Open the ferrite bead and loop the cable through the ferrite bead twice. Close the ferrite bead and plug the connector back in.

INSTALL THE PC BOARD INTO A NON-JAMMA GAME CABINET

  • Replace the existing CPU board and sound board with the MORTAL KOMBAT 3 CPU/Sound board. Use the 1/4" PCB mounting spacers and surplus screws to secure the CPU/Sound board to the electronic rack, or the inside wall of the cabinet.
  • Leaving several inches of wire, cut the wires at the coin door, control panel switches, (which already may be disconnected), speaker, and power supply. Remove the harness from the cabinet. Leave your power supply chassis as is. NOTE: Be sure that all spliced wires are well insulated with black electrical tape.
  • Install the JAMMA cable provided with the kit. Players 1 and 2, the coin door, and the power supply wires are bundled together in individual groups. Insure that the cable is properly dressed and supported.

AN CAUTION

Properly insulate any unused wires within the JAMMA cable, especially gray, gray-green, and grayyellow wires. This is a fully wired JAMMA cable. Many of the wires will not be used for this kit. These wires have been installed so that you can use this cable for future kits.

  • Connect the JAMMA cable to the CPU/Sound board. Use the Cabinet Wiring Diagram for reference and solder the correct JAMMA cable to the speaker. Then, connect the wires to the coin door, power supply and control panel. Player 1 has white-‘color stripe’ wires, except for Start 1 which has a solid white wire. Player 2 has violet-‘color-stripe' wires. Use the Cabinet Wiring Diagram in section two, or the Control Panel Wire Color list on the back cover, for reference when connecting these wires to the player 1 and 2 control panel switches.
  • Connect auxiliary cable to P12 of the CPU/Sound board. Use the Cabinet Wiring Diagram in section two, or the Control Panel Wire Color list on the inside back cover for reference when connecting these wires to the Low Punch and Low Kick switches.
  • Place the FBI Warning Label next to the CPU/Sound board. Be sure the label is completely visible.

1-9

Page 14

GAME FEATURES STARTING UP Switch on power to the game. A “rug” pattern appears on the screen. When the “rug” pattern ends, the screen shows Checking Scratch RAMS, then Checking ROMS. The next screen shows the revision level, the CMOS test results, and the coin setting. (Refer to page 1-4 for proper chip locations.) The game goes into the Attract Mode.

Insert the desired amount of coins, bills or tokens. Select which player receives the credit by pressing the appropriate Start button. Use the joysticks to select an on-screen character, and any control panel button to confirm your choice. Game play starts automatically once the on-screen characters are chosen.

NOTE When an error is detected during the Start-up tests, game start-up does not progress, and an error message appears on the screen.

PLAYER CONTROLS ¢ Start Button Each player has a Start bution. The Start buttons allow one or two players to begin or continue play.

« Joysticks Each player has a joystick which he uses to control an on-screen character. The player can make the on-screen character move, jump or duck.

¢@ High Kick/High Punch Buttons These buttons allow the on-screen character to kick or punch an opponent in the upper body.

¢ Low Kick/Low Punch Buttons These buttons allow the on-screen character to kick or punch an opponent in the lower body.

« Block Buttons These buttons allow the on-screen character to block an opponent's punch, kick, or special move.

« Run Buttons These buttons speed up the on-screen character.

NOTE Use joystick and button combinations to discover secret moves.

OO O a) puck Low Low ouck Low Low O PUNCH ack ©) PUNCH wick

Control Panel

1-10

Page 15

MENU SYSTEM OPERATION

OPERATION All game audits, adjustments and diagnostics are options of the Main Menu. Each option, in turn, has its own menu that lists several choices which you may act upon as desired.

Press the Begin Test switch on the coin door to open the Main Menu (shown below). Game adjustments, bookkeeping and diagnostics are all accessible from this menu.

Use either joystick to move the cursor up and down the menu screen. Notice that the options are highlighted in sequence. Press any button on the control panel to open a highlighted option.

NOTE Only highlighted options can be opened.

MAIN MENU

To exit the Main Menu and return to the Attract Mode, use either joystick to select EXIT TO GAME OVER and press any button.

Page 16

DIAGNOSTIC TESTS Use either joystick to select the Diagnostic Menu and any button to open it. Then, use either joystick to move the cursor up and down the menu and any button to open a highlighted option.

To exit the Diagnostic Menu, use either joystick to select RETURN TO MAIN MENU and press any button.

DIAGNOSTIC MENU

Switch Test The Switch Test allows the operator to test the switches on the control panel and in the coin door.

Use either joystick to highlight the Switch Test and any button to begin the test.

During the Switch Test the top of the screen shows the control panel switches while the bottom of the screen shows the coin door switches. Press a control panel or coin door switch and the switch location on the screen fights. Release the switch and the screen returns to normal.

© puver 1 siaRr paver 2 stan

O° oe O CO O © © © To exit the Switch Test, press both Start buttons together.

O OO

O O OO CO OO OC O con can 2 con 3 cone senver saw vest O O O ne vou oN vou uF ou

Page 17

DIP Switch Test The DIP Switch Test allows the operator to check or change the position of the DIP Switches on the CPU Board.

Use either joystick to select the DIP Switch Test. Press any button to access the DIP Switch Setting Tables. The screen displays the current settings. To change a Setting, slide the switch to the desired Position. Check the screen to verify the new setting. In some cases, setting a function to OFF actually enables the function. For example, setting DIP Switch Coinage to Off enables DIP Switch Coinage.

Press any button to return to the Diagnostic Menu.

DIP Switch 1 Setting Table

  • Indicates factory setting. SW. 8 SW.7_ | SW.6 | SW.5 | SW.4 | SW.3 | SW.2 Coinage DIP Switch Off* CMOS On Coin Settings
USA1Ger. 1Fr.1Off*Off*
USA2Ger. 2Fr2OnOff
USA3Ger. 3Fr.3OffOn
USA 4Ger. 4Fr.4OnOn
USAECAGer.ECAFr.ECA | OffOff
N/UN/UNUOnOff
N/UOffOn
Free Pla)OnOn

Country USA Off*

Germany Off

France On

Not Used On 1 Count/Coin Totalizer Test Switch Game Mode otf Test Mode On

DIP Switch 2 Setting Table Sw.8 | Sw.7 [| SW.6 | SW.5 | SW.4 [ sw. 3 | SW.2 | SW.1 Violence On Off" On Blood In Game Off” | On Not Used Off* On Attract Sounds On Off" On Not Used Off* On Dollar Bill Validator Not Installed Off*

Installed On

Do Power Up Test Off" Skip Power Up Test On Not Used Off On

Page 18

CPU Board Test The CPU Board Test, much like the Start-up Test, allows the operator to check the RAMS and the ROMS.

Select the CPU Board Test with either joystick. Press any button to start the test.

When this test is activated, a "rug" pattern appears on the screen. The screen then changes to show the layout of the RAMS and ROMS. A chip location that is shown as black with a white outline is used. A chip location that is shown as gray with a white outline is not used. During the test, chips are good if they turn green and faulty if they turn red. Turn to page 1-4 for the exact chip location.

The test pauses if a faulty RAM or ROM is detected. Press any button to continue the test.

Sound Board Test This test allows the operator to listen to some of the sounds this game is capable of producing.

Use either joystick to select the test, then press any button to open the menu. The screen displays two test options. Use either joystick to select an option and any button to begin the test.

SOUND TEST MENU

GENERAL TEST analyzes the sound circuitry. The screen shows a list of error codes. A successful test causes a single "tone" to sound. Detection of a fault causes a series of tones or no tone at all to sound. Press any bution to return to the Sound Test Menu.

PLAY SOUNDS tests synthesized and digitized sounds from the CPU/Sound board. Advance to the next sound with any button. Use either joystick to end the test.

Select RETURN TO MAIN MENU or BACK TO DIAGNOSTIC MENU and press any button.

Page 19

Monitor Patterns The Monitor Patterns Test provides a menu for testing the monitor.

Select the test with either joystick. Press any button to open the test menu. Once the menu is open, use either joystick to select an option, and any button to begin it. Press any button again to return to the Monitor Patterns Menu.

MONITOR PATTERNS MENU

The RED, GREEN and BLUE SCREEN tests fill the screen with either red, green or blue. Press any button to return to the Monitor Patterns Menu.

The COLOR BARS test fills the screen with several shades of colors to help with red, green and blue level adjustments. Each color should appear sharp and clear. Press any button to return to the Monitor Patterns Menu.

The CROSSHATCH PATTERNS test fills the screen with a grid and a series of dots. The grid and the dots should be clear. The dots should be round. Press any button to return to the Monitor Patterns Menu.

If any of the tests show a need for adjustment, use the proper knobs on the Monitor Controls board. The Monitor Controls board is located just inside the control panel opening, beneath the monitor.

To exit this test, use either joystick to select RETURN TO MAIN MENU or BACK TO DIAGNOSTIC MENU, then press any button.

Burn-in Test The Burn-in Test continually repeats the CPU Board Test. Use this test to find intermittent CPU Board problems. The Audit Table specifies the number of Burn-in cycles that have been successfully completed.

Use either joystick to select the test, then press any button to activate it. When the Burn-in Test detects an error the test stops and an error message is displayed on the screen.

To exit this test, switch the game off, then on again.

Page 20

COIN BOOKKEEPING

The Coin Bookkeeping Table records the coin box totals and the game play counters.

Use either joystick to select the Coin Bookkeeping Menu, then press any button to open it.

COIN BOOKKEEPING TABLE

TOTAL COLLECTION TABLE

To exit Coin Bookkeeping, use either joystick to select RETURN TO MAIN MENU and press any button.

Page 21

GAME AUDITS Use joystick to select the Game Audits Menu, then press any button to open it. Page through the available audits by selecting NEXT AUDIT PAGE or LAST AUDIT PAGE. Select RETURN TO MAIN MENU and press any button to exit Game Audits. Game audits cannot be set. They can only be cleared.

PAGE 1 OF AUDIT TABLE

Agnes eo

PAGE 2 OF AUDIT TABLE

1-17

Page 22

GAME ADJUSTMENTS The Game Adjustments allow the operator to customize the game.

Use either joystick to select the Game Adjustments Menu. Press any button to open the menu.

The Game Adjustments Menu offers several options. Each option has several choices. Use either joystick to select an option, then press any button to open the option. The next menu screen provides a setting value. Use either joystick to change the setting value and press any button to lock it in.

To exit the Adjustments Menu, use either joystick to select RETURN TO MAIN MENU, and press any button.

NOTE Adjustment values set by DIP SWITCH, override adjustment values set by the menu system.

GAME ADJUSTMENT MENU

Game Adjustments

Standard Pricing Standard pricing allow the operator to choose any of the "standard" selections from the Standard Pricing Table. See page 1-20.

Modify the setting value with either joystick. Press any button to lock in the new value and return to the Adjustments Menu.

Custom Multipliers Customize the internal coin chute muttipliers for each chute.

Custom Pricing Custom pricing allows the operator to install pricing other than that of the Standard Pricing Table. Custom pricing also allows the operator to select the maximum amount of credits per game, the amount of credits required to start a game, and the amount of credits required to continue a game. This option is being adjusted from the DIP Switch settings. See page 1-21.

Modify the setting value with either joystick. Press any button to lock in a new value and return to the Adjustment Menu.

Page 23

Game Adjustments Continued...

Free Play This option selects free play. The setting choices for this adjustment are: -No

  • Yes
  • Factory Setting: No

Computer Difficulty This option determines how tough the computer opponents are. The setting choices for this adjustment are:

  • (1) Extra Easy
  • (2) Easy
  • (3) Medium
  • (4) Hard
  • (5) Extra Hard
  • Factory Setting: Medium
Page 24

STANDARD PRICING TABLE

Name Setting - Coin/Credit Coin 2

USA11/25¢(2 to Start, 2 to Continue)25¢
USA2125¢(2 to Start, 1 to Continue)28e
USA3125¢(1 to Start, 1 to Continue)28¢
USA41/50¢, 3/$1.00(1 to Start, 1 to Continue)25¢
USA51/50¢, 4/$1.00(2 to Start, 1 to Continue)28¢
USA 6V50¢(1 to Start, 1 to Continue)25¢
USA71/50¢, 3/$1.00(1 to Start, 1 to Continue)25¢
USA81/50¢, 4/$1.00(2 to Start, 2 to Continue)25¢
USA91/25¢(3 to Start, 2 to Continue)25¢
USA 101/25¢(3 to Start, 3 to Continue)25¢
USA ECA1/25¢, 4/$1.00__(2 to Start, 2 to Continue)A25¢
German 11/1DM, 6/5DM5DM
German 21/1DM, 7/5DM5DM
German 31/1DM, 8/5DM5DM
German 41/1DM, 5/SDM5DM
German 51/1DM, 6/5DMSDM
German ECA1/1DM, 2/2DM, 6/5DM20M
France 12/5F, S/10F10F
France 22/5F, 4/10F10F
France 31/5F, 3/10F10F
France 41/5, 2/10F10F
France 52/5F, 5/10F, 11/2 x 10F10F
France 62/5F, 4/10F, 9/2 x 10F10F
France 71/5F, S/10F, 7/2 x 10F10F
France 81V/5F, 2/10F, 5/2 x 10F10F
France 91/3 x 1F, 2/5F5F
France 10V2 x 1F, 3/5F5F
France 111/3 x 1F, 2/5F, 5/2 x 5FSF
France 121/2 x 1F, 3/5F, 7/2 x 5FSF
France ECA1/3 x 1F, 2/5F, 5/2 x 5FSE

4/2 x 25¢, 3/$1.00 $1.00 VIF, 6/5F 5F WF, 7/5F 5F IAF, 8/SF SE

1/500 lire500 lire500 lire
UK 1 ECA1/50P, 3/21£150P
UK2ECA1/50P, 2/21£150P
UK3ECA1/30P, 2/50P, 5/£1£150P
UK41/50P, 3/21£150P
UK51/50P, 2/£1£150P
Spain 11/100 peseta, 6/500 peseta100 peseta500 peseta
Spain 21/100 peseta, 5/500 peseta.100 peseta500 peseta
Australia 11/3 x 20¢, 2/$1.0020¢$1.00
Australia 2415 x 20¢, 1/$1.0020¢$1.00
Japan 11/100 yen100 yen100 yen
Japan 22/100 yen100 yen100 yen
Austria 11/5 schilling, 2/10 schilling5 schilling10 schilling
Austria 21/2 x5 schilling, 3/2 x 10 schilling5 schilling10 schilling
Belgium 1V20F20F20F
Belgium 23/20F20F20F
Belgium 32/20F20F20F
Belgium ECA1V20FSOF20F
Sweden1/3 x1 krona , 2/5 krona1 krona5 krona.
New Zealand 1 | 1/3x20¢20¢20¢
New Zealand 2_|1/2 x 20¢20¢20¢
Netherlands4/1 guilder, 3/2.5 guilder1 guilder2.5 guilder
Finland4/1 markka4 markka1 markka
Norway1/2 x 1 krone, 3/5 x 1 krone1 krone1 krone,
Denmark1/2 x1 krone, 3/5 krone, 7/2 x § krone1 krone5 krone
Antilles1/25¢, 4/1 guilder25¢1 guilder
Hungar1/2 x 10 forint, 3/2 x 20 forint10 forint20 forint

1-20

Page 25

1)

2) CUSTOM PRICING

CUSTOM PRICING MENU

Coins inserted accumulate units. This adjustment specifies the number of units given for each coin in the fourth chute (see "Units/Credit’).

Coins inserted accumulate units. This adjustment specifies the number of units given for each bill validated (see "Units/Credits").

This is the number of coin units required to buy one credit.

There is one bonus credit awarded after this many coin units have accumulated.

This is the minimum number of units required before any credits are awarded.

Each player needs this many credits to begin a game.

Each player needs this many credits to continue a game.

The detailed bookkeeping screen shows total collection based on this many coins per dollar. (Set to zero to disable the display of money totals.)

This is the limit for the credit counter. Additional coins inserted will be lost (factory setting: 30).

1-21

Page 26

UTILITIES The Utilities Menu allows the operator to clear the game's bookkeeping memory.

Use either joystick to select the Utilities Menu, then press any button.

Use either joystick to select a utility. Press any button to activate the selection.

UTILITIES MENU

Once the selection is made, a dialogue box appears, and the operator can choose to reset the utility.

For example:

CLEAR COIN COUNTERS? ARE YOU SURE?

YES

Use either joystick to choose a setting value. Press any button to lock in the new setting value.

To exit the Utilities Menu, use either joystick to select RETURN TO MAIN MENU, then press any button.

1-22

Page 27

HARDWARE INFO

The Hardware Information screen gives the date the game was manufactured and the game's serial number.

HARDWARE INFO MIDWAY MANUFACTURING COMPANY

WOLF UNIT

SERIAL NUMBER: XXXXXXXX

DATE OF MANUFACTURE: XX/XX/KXXX

Press any button to exit this screen and return to the Main Menu.

1-23

Page 28

VOLUME ADJUST The Volume Adjust feature allows the operator to determine the sound and music level of the game.

The volume level can be adjusted from either the Attract Mode or the Menu System. Press the Volume Up button to raise the volume level and the Volume Down button to lower the volume level. Either joystick can also be used to raise or low the volume level. The current volume level is shown with a red bar.

Press any button to return to the Main Menu.

VOLUME ADJUST

MAX.

1-24

Page 29

TROUBLESHOOTING

PROBLEM 1)

2)

3)

4)

5)

6)

7)

8) No picture or distorted picture.

Turn game On and nothing happens.

No sound.

No general illumination.

Press Start button and nothing happens.

No credit given for number of coins inserted.

Too many credits for number of coins inserted.

Game stays in test mode. POSSIBLE SOLUTION 1)

2)

3)

4)

5)

6)

7)

8)

1-25 Check for faulty video board or monitor. Check for disconnected video signal cable.

Check line fuse. Check for +5Vdc at pins C, D, 3 and 4 of the JAMMA connector.

Check the speaker and the speaker connection to pin L and 10 on the JAMMA connector. Check volume control setting. Check for +12Vdc at pins F and 6 on the JAMMA connector. Check for -5Vde at pins E and 5 on the JAMMA connector,

Check the 1A, S.B. fuse in the AC power pack assembly.

Check for open wires between the button and the CPU board. Check for contamination on CPU board pins or the Start button switch blade contacts. Check for proper ground.

Check DIP switch coin settings. Check for contamination on the coin switch contacts. Check for an open wire between Coin Switch 1 and pin 16 on the JAMMA connector or Coin Switch 2 and pin T of the JAMMA connector.

Check the game pricing settings. Check for a short between pins T & 16 on the JAMMA connector.

Check that the switch #8 of DIP switch bank #2 is set to off.

Page 30

NOTES

1-26

Page 31
Scan of page 31

This page is a drawing, shown as the original scan.

Page 32

JAMMA Chart

FUNCTION WIRE COLOR WIRE COLOR _| FUNCTION Black Black

+5VDC Red -5VDC Yellow +12VDC Orange Key Coin Counter 2__| Brown-Red Coin Counter 1

Speaker + Speaker-

Video Red Video Blue Video Ground Video Green Video Sync Service Credits] White-Gray _ Slam Titt Black-Green Black-Red Violet-White Violet-Black Violet-Brown Violet-Red Violet-Orange Violet-Yellow Violet-Green Violet-Blue Black-Blue Black-Brown

White-Black White-Brown White-Red White-Orange White-Yellow White-Green White-Blue White-Violet

SOLDER SIDE COMPONENT SIDE 10 jalo |olp IN)<|x<|/S/</Cla]/m|D) V)ZJZ/-|A]C| Tl n|mM|olo|w| >

2-2

Page 33

INTERBOARD WIRING

N/e_GND_| [357] oS * CPU/SOUND BOARD

Gei|*PUUN

a A—18968—40039

A

BILL_INBLK-WHT7
COIN 4BLK-YEL6
+12v‘ORG:aPg
+RED3

COIN-3_——BLK=ORG 1] 3

GND BLK 1

N/C KEY 3° N 8 N/C 7

N/C6PIO

: INTERLOCK_BLK—GRY P fOLUME 2 ;

4 SWITCH D GRY-VIO 14 9 SWITCH C~GRY=SE 1] 13 4 “SWITCH BGRY-GRN 1] 55 4 SWioCH A_GRY-YEL 1

4 RIGHTGRY-ORG10
LEFT—GRY=RED_I9
DOWNGRY=BRN 1] 3Pit

4_uP GRY=BLK_ [17

NZC5PLAYER 4

NZC a

N/C. 2

  • Nfe TS

N/C 15 3 SWITCH _D BLU-VIO- 14 3 SWITCH B BLU-GRN |] +> S_SWITCH A SLU=YEL "1 SRIGHT —BLU=CRG_ | 9

LEFTBLUSRED[1gP12
+ OWNBLU-BRRB

Saat sees, | PLveR 3 N/C 5 N/E 3 N/C 3 N/C 2 N, 1 i

Page 34

TWOIdAL) T3NVd TOSINOO ’ * tre ! treet tant in it

(9661-H oT ONAS 3H MO4 LNON'd INI TBNve TOMLNOD »* ¥ J¥INDIN SHOLNON TAS.

14410 NOS WVYOVIC ONIMIM LANIGVD

2-4

Page 35

COIN SWITCH AND METER WIRING

OPTION 1 COIN SWITCH 1 WA +5V

COIN SWITCH 2 L — METER A JAMMA PIN 16

GROUND JAMMA PIN 8

OPTION 2 COIN SWITCH 1 A a JAMA PIN 16 +5V WA COIN ii IT WITCH COIN SWITCH 2 —_ 8 c A JAMMA PIN T METER

GROUND JAMMA PIN 8

!! WRONG WAY !!

Do not connect the coin switches in this manner. This circuit is INCORRECT, and will cause twice as many credits per coin.

COIN SWITCH 1 pe JAMMA PIN 16

COIN SWITCH 2 WA

B= AMMA PIN T

GROUND

Page 36

NOTES

Page 37

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 38

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 39

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 40

7~S~ N -;

Page 41

Control Panel Wire Color List

PLAYER ONE PLAYER TWO

FUNCTIONWIRE COLORFUNCTIONWIRE COLOR

Start White Start Violet-White

Up White-Black Up Violet-Black

Down White-Brown Down Violet-Brown

Left White-Red Left Violet-Red

Right White-Orange Right Violet-Orange

High Punch White-Yellow High Punch Violet-Yellow

BlockWhite-GreenBlockViolet-Green
High KickWhite-BlueHigh KickViolet-Blue
Low PunchBlue-BlackLow PunchBlue-Yellow
Low KickBlue-BrownLow KickBiue-Green
Run (Speed)Blue-RedRun (Speed)Blue
Page 42

WARNINGS & NOTICES

WARNING : USE OF NON-MIDWAY PARTS OR CIRCUIT MODIFICATIONS MAY CAUSE SERIOUS INJURY OR EQUIPMENT DAMAGE! USE ONLY MIDWAY AUTHORIZED PARTS.
  • For safety and reliability, substitute parts and modifications are not recommended.
  • Substitute parts or modifications may void FCC type acceptance.
  • This game is protected by federal copyright, trademark and patent laws. Unauthorized modifications may be illegal under federal law. This also applies to MIDWAY logos, designs, publications and assemblies. Moreover, facsimiles of MIDWAY equipment (or any feature thereof) may be illegal under federal law, regardless of whether or not such facsimiles are manufactured with MIDWAY components.
WARNING
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generated, uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

NOTICE - FCC WARNING STICKER |. THIS KIT WAS TESTED IN A MIDWAY UNIVERSAL VIDEO CABINET AND A DYNAMO_HS-5 CABINET, AND FOUND TO COMPLY WITH FCC PART 15 CLASS A REQUIREMENTS. IF INSTALLED IN A MIDWAY UNIVERSAL VIDEO CABINET, OR A DYNAMO HS-5 CABINET, THE FCC STICKER (16-9306) SUPPLIED IS TO BE PLACED ON THE REAR OF THE CABINET. Il. INSTALLATION OF THIS KIT INTO ANY OTHER PRODUCT DOES NOT GUARANTY COMPLIANCE WITH THE FCC REQUIREMENTS. YOU ARE SOLELY RESPONSIBLE, AND MIDWAY WILL HAVE NO RESPONSIBILITY, FOR FCC COMPLIANCE FOR INSTALLATIONS IN OTHER PRODUCTS. THE FCC

WARNING STICKER SUPPLIED SHOULD NOT BE INSTALLED ON THE CONVERTED PRODUCT UNTIL FCC COMPLIANCE IS VERIFIED
WARNING Prevent shock hazard and assure proper game operation. Only plug this game into a properly grounded outlet. Do not use a cheater plug to defeat the power cord's grounding pin. Do not cut off the ground pin.

NOTICE No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may be transmitted, or otherwise copied for public or private use, without permission from the publisher.

Entire contents of this manual copyright © 1995 MIDWAY Manufacturing Company, INC. All Rights Reserved. DYNAMO HS-5 IS A TRADEMARK OF DYNAMO CORPORATION.

FOR SERVICE: CALL YOUR AUTHORIZED MIDWAY DISTRIBUTOR.

MIDWAY MANUFACTURING COMPANY 3401 N. CALIFORNIA AVE. CHICAGO, IL 60618