CATHODE RAY TOMES

X-Men vs Street Fighter

X-Men Vs. Street Fighter (Europe 961004) (Capcom, 1996) · Manual · 22 pages · 28 sections · original scan

Page 1

OPERATORS MANUAL

WARNING

This game is for use in the United States of America

and Canada. Sales, export or operation outside of

these countries may be constructed as copyright and

trademark infringements and is strictly prohibited. Violators are subject to severe penalties and will be prosecuted to the full extent of the law.

Page 2

CAPEOM’ coin-op, inc. X-MEN™ vs, STREET FIGHTER™

THANK YOU FOR PURCHASING X-MEN™ vs. STREET FIGHTER™, WE INVITE YOU

TO USE THE FOLLOWING MAILING ADDRESS, TELEPHONE OR FAX NUMBER FOR

PARTS OR SERVICE INFORMATION CONCERNING THIS GAME:

CAPCOM® COIN-OP, INC.

ATTN: FIELD SERVICE - VIDEO PRODUCTS

3311 N. KENNICOTT AVENUE

ARLINGTON HEIGHTS, ILLINOIS 60004 PHONE: (847) 797-6100 FAX: (847) 797-6306 THE SERIAL NUMBERS OF YOUR KIT ARE LOCATED ON THE GAME CARTRIDGES AS SHOWN BELOW. PLEASE HAVE THESE SERIAL NUMBERS AVAILABLE WHEN CONTACTING US FOR SERVICE INFORMATION.

PLEASE RECORD YOUR KIT SERIAL NUMBERS HERE: “FULL” KIT A-CARTRIDGE SERIAL # B-CARTRIDGE SERIAL # AAMA SERIAL # “B” KIT B-CARTRIDGE SERIAL # _ AAMA SERIAL # “E” KIT A-CARTRIDGE SERIAL # B-CARTRIDGE SERIAL # AAMA SERIAL # “BE” KIT B-CARTRIDGE SERIAL # AAMA SERIAL #

[Proprietary and confidential information, not to be disclosed or without the CAPCOM® COIN-OP, INC.

Page 3

@APEOMI* coin-op, nc. X-MEN™ vs. STREET FIGHTER™

TABLE OF CONTENTS

Warranty Information ——auanssenssnssescscatsreacacereucaeensuceeneaesucacacsnseensessessenensaeereneen ii

Kit Inspection anaestststestseseseescseseeecseseseesesesesecessesesesseesseesseseeaesesecseseeee 1

Kit Installation “FULL” Kit Cabinet Preparation Control Panel Overlay Reassembly of Components Control Panel Wiring Remote Volume/Test Switch Game Cartridges Cabinet Graphics

Cabinet Grahics Game Cartridge ‘E” Kit & “BE” Kits Cabinet Grahics Game Cartridge

Test Mode Test Menu Accessing the Menu Selecting an Item Closing the Menu Menu Item Descriptions Configuration Menu System Configuration Game Configuration

Wiring References JAMMA Connections Auxiliary Cable Connections

Template : Control Panel Drill Hole(s)

[Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM@ COIN-OP, INC. i

Page 4

GANPEOM* co-op, inc. X-MEN™ vs, STREET FIGHTER™

LIMITED PRODUCT WARRANTY (APPLIES TO DOMESTIC SALES ONLY)

CAPCOM® COIN-OP, INC. (Seller), warrants only to the initial purchaser of its products, that the items listed below are free from defects in material and workmanship under normal use and service for the warranty periods specified:

A. CPS II System Cartridges One (1) Year B. Electronic and Mechanical Components: Ninety (90) days

No other part of Seller's products are warranted.

Warranty periods are effective from the initial date of shipment from seller to its authorized distributors.

Seller's sole liability shall be, at its option, to repair or replace products which are returned to Seller during the warranty periods specified, provided:

A. Seller is notified promptly upon discovery by buyer that stated products are defective;

B. Such products are properly packaged and then returned, prepaid to Seller's designated plant.

This warranty does not apply to any parts damaged during shipment or handling, or due to improper installation or usage, or alteration. In no event shall Seller be liable for any anticipated profits, loss of profits, loss of use, incidental or consequential damages or any other losses incurred by the customer in connection with the purchase of a CAPCOM® COIN-OP, INC. product.

WARRANTY DISCLAIMER

EXCEPT AS SPECIFICALLY PROVIDED IN A WRITTEN CONTRACT BETWEEN SELLER AND PURCHASER, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

IMPORTANT NOTICE

THIS SHIPMENT HAS BEEN CAREFULLY INSPECTED AND PROPERLY PACKAGED BEFORE LEAVING THE FACTORY. WE CANNOT ASSUME RESPONSIBILITY FOR BREAKAGE THAT MAY OCCUR DURING TRANSPORTATION OF THE GAME. IF THIS GAME IS DAMAGED UPON RECEIPT FROM THE CARRIER, IMMEDIATELY NOTIFY THE CARRIER AND FILE A DAMAGE REPORT.

ii Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM@ COIN-OP, INC.

Page 5

CAPO’ co-op, inc. X-MEN™ ys, STREET FIGHTER™

KIT INSPECTION

There are four kits available for cabinet conversion to X-MEN™ vs. STREET FIGHTER™:

  • XVS1000 (“FULL” kit) contains the complete game cartridges, all necessary graphics, and replacement joysticks and button switches. The “FULL” kit is intended for conversion of most JAMMAcompatible, horizontal screen cabinets.
  • XVS1000B (“B” kit) contains the game memory cartridge (B-cartridge) and must also be installed to a current CAPCOM® System II game. It includes all the necessary game graphics for a cabinet conversion (marquee, control panel overlay, monitor card, etc.). This kit is intended for conversion of most JAMMAcompatible, horizontal screen cabinets, currently configured with a CPS II system board (A-cartridge).
  • XVS1000E (“E” kit) contains the complete game cartridges. some game graphics, and an auxiliary cable for connections to the control panel and remote test bracket This kit is intended for conversion of most 6-button, JAMMA-compatible, horizontal screen cabinets.
  • XVS1000BE (“BE” kit) contains the game memory cartridge (B-cartridge) and must also be installed to a current CAPCOM® System II game. It includes a game instruction decal and an operators manual. This kit is intended for conversion of most 6-button , JAMMA-compatible, horizontal screen cabinets, currently configured with a CPS II system board (A-cartridge).

Check that all parts have been shipped (V ) with your kit. If any parts are missing, contact your distributor immediately.

KIT PARTS LIST

XVS1000 | XVS1000B | XVS1000E | XVS1000BE PART NO. DESCRIPTION v XVS1400 CPS II System Cartridges (A/B ) XVS1400B CPS II System Cartridge ( B ) GE1200 Monitor Card AW00233 Marquee AW00216 Overlay, Control Panel a Decal, Joystick & Button Switches AW00147 Decal, Cabinet Side AW00234-3 Decal, Monitor Card Instruction PMO00176-KIT Manual, Operators GE2030 [roystick, 8-way 16-0130 Switch, 1-Player Start Button (Whitey | 16-0131 Switch, 2-Player Start Button (White) 16-0133 Switch, Button (Red) 16-0134 Switch, Button (Blue) 16-0136 Switch, Button (Green) 03-0052 Cable, Auxiliary Volume/Test 13-0066 Bracket, A-Cartridge Mounting $C00104-05 Screw, Wood 2lejelelelejeleleselelelelejele)

[Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC, 1

Page 6

CAPGOL* coin-op, inc. X-MEN™ vs, STREET FIGHTER™

CAUTION

Please read the following instructions to keep the PC board in good condition:

Do not block the ventilation slots.

#Do not drop or bump the board.

Do not spill any liquids on the case.

Do not disassemble the case.

ATTENTION

The product that you have purchased contains a recyclable battery. At the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery into the municipal waste system. Check with your local solid waste official for details in your area for recycling options or proper disposal.

DISASSEMBLING THE CASE OR REMOVING THE STICKER MAY CAUSE THE TERMINATION OF YOUR REPAIR WARRANTY

OF YOUR REPAIR WARRANTY.

[Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 7

® CARCOM\ COIN-OP, INC. X-MEN™ vs, STREET FIGHTER™

“FULL” KIT INSTALLATION

Ay WARNING:

MAKE SURE ELECTRICAL POWER TO THE GAME IS OFF BEFORE STARTING THE KIT INSTALLATION.

CABINET PREPARATION

  • Remove the marquee glass, old marquee overlay, and the old cabinet graphics.
  • Disconnect and remove the old printed circuit board(s) from the cabinet.
  • Remove or open the control panel, and disconnect and remove the buttons and joystick(s) from the control panel.
  • Remove any covering from the control panel overlay, and then remove the control panel overlay.
  • Place the Drill Hole Template (included in this manual) over the control panel to determine where any new holes should go. Center punch any needed new holes on the control panel.
  • Cut out the new holes using a 1-3/16" hole saw.
  • If there is an additional control panel cover (such as plastic or lexan) that will be utilized, cut any additional holes using the same template.
  • Plug up unused holes with wood dowel (1-1/8" diameter), being careful to sand any rough edges, or use available button plugs.

KIT INSTALLATION

Control Panel Overlay Installation (See Figure 1)

  • The control panel overlay in the kit is oversized to accommodate most control panel sizes. Center the overlay on the control panel, leaving some excess material at the edges.
  • Remove the protective backing from the overlay and press it down on the control panel, keeping it properly aligned. Press it down firmly, smooth out any bubbles, and press it over the edges.
  • Trim any excess from the overlay. Place the drill hole template on top of the overlay, aligning it with the joystick holes. Pierce through the overlay at each control panel hole. Then, cut away overlay material covering the joystick and button holes. Remove the template and clean off the overlay.
  • Peel off the backings of the 6-button and joystick decals, align over the control panel holes, and press in place on the overlay (refer to the drill hole template for proper placement). Using a knife, trim material from the center hole of the joystick decal.
  • Install the control panel cover (*if required).

Figure 1: Overlay Installation

Reassembly of Components

  • Install all buttons and retaining rings on the control panel as shown in Figure 2. Install two RED buttons to the immediate right of each joystick, install two GREEN buttons to the right of the red ones, and install two BLUE buttons to the right of the green ones.

[Proprietary and confidential information, not to be disclosed or ‘without the express permission of CAPCOM® COIN-OP, INC. 3

Page 8

CAPEOM* coin-op, inc. X-MEN™ vs, STREET FIGHTER™

Control Panel Red Green Blue Red Green Blue

& eb S evar

Red Green Blue Red Green Blue

Buttons.

Retaining Rings

Switches.

FIGURE 4 FIGURE 2 Joystick Installation Control Panel Buttons and Switches connector and the appropriate control or switch wire on

  • Notice that there are two white buttons. (See the normally-open connector of the switch. Figure 3.) Install the PLAYER ONE button on the top left-hand side of the control panel, and the PLAYER 18. Reconnect the existing JAMMA connectors to the TWO button on the top right-side of the control panel. control panel according to Table 1. The WHITE buttons are START buttons.
  • Connect the Player 1 and Player 2 buttons to the auxiliary cable harness connectors shown in Figure 5. Make the connections according to Table 2.

TO GAME CASE CONNECTOR 1 Player a

FIGURE 3 Function and Start Buttons

  • Install the switched on the buttons as shown in Figure 2. Orient the switches so that when a button is pressed, the red contact on the switch is depressed.
  • Install the joysticks on the control panel as shown in Figure 4.

Wiring TO VOLUME & TEST

NOTE: SWITCHES

All switch wires used in this game must be wired to the normally-open connection on the switches. Each switch FIGURE 5 requires a ground wire on the common Auxiliary Cable Harness

4 [Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 9

@ CAPEOM* co-op, inc. X-MEN™ vs. STREET FIGHTER™

JAMMA CONNECTS

CONNECTOR REF. | *WIRE COLOR TO ps | WHITE/BLACK PLAYER 1 PLAYER 1 19 WHITE/BROWN 20 WHITE/RED 21 WHITE/ORANGE PLAYER 1 JOYSTICK 22 WHITE/YELLOW, 23 WHITE/GREEN_ PLAYER 1

PLAYER 1 PLAYER 1 PLAYER 1 COMPONENT JOYSTICK FUNCTION UP JOYSTICK JOYSTICK

PUNCH BUTTON PUNCH BUTTON PUNCH BUTTON DOWN LEFT RIGHT LIGHT MIDDLE HEAVY

VIOLET/BLACK VIOLET/BROWN VIOLET/RED VIOLET/ORANGE VIOLET/YELLOW PLAYER 2 PLAYER 2 JOYSTICK UP. JOYSTICK DOWN PLAYER 2 JOYSTICK LEFT PLAYER 2 PLAYER 2 VIOLET/GREEN VIOLET/BLUE PLAYER 2 JOYSTICK PUNCH BUTTON PUNCH BUTTON PLAYER 2 PUNCH BUTTON

Table 1: JAMMA Wiring Connections RIGHT LIGHT MIDDLE HEAVY

  • Wire Color Note: Wire colors shown are according to the AAMA -AMOA Standard for wire color assignments; your harness may contain different colors than shown above.

AUXILIARY CABLE CONNECTOR REF. WIRE COLOR BLACK BLUE CONNECTS TO

PLAYER 1 COMPONENT FUNCTION

KICK BUTTON. LIGHT RED PLAYER 1 KICK BUTTON PINK PLAYER 1 KICK BUTTON MIDDLE HEAVY

BLACK PLAYER 2 KICK BUTTON COMMON GRAY/YELLOW PLAYER 2 KICK BUTTON LIGHT PINK/YELLLOW PLAYER 2 KICK BUTTON MIDDLE PURPLE/YELLOW

GRAY/YELLOW PLAYER 2 KICK BUTTON HEAVY

TEST BRACKET VOLUME SWITCH UP PINK/YELLOW TEST BRACKET VOLUME SWITCH BLACK/WHITE TEST BRACKET VOLUME SWITCH

Table 2: Auxiliary Cable Wiring Connections DOWN COMMON

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC. 5

Page 10

® (CARCOM| COIN-OP, INC. X-MEN™ vs. STREET FIGHTER™

  • An optional Test/Volume bracket (see Figure 6) is available through your local Capcom distributor (part number 03-0050). Your cabinet may already contain this bracket. When installing, the bracket should be mounted inside the coin door and on top of the cashbox for easy access.
NOTE: The A-cartridge also contains the same Test and Volume functions found on the test bracket.

'v300500 Figure 6: Test Bracket

Wiring of the Test Bracket requires connections to both the main JAMMA harness as well as the Auxiliary Cable hamess (refer to Table 3).

LEAD WIRE SWITCH CONNECTS COLOR FUNCTION TO VOLUME-UP | AUX. CABLE ‘29°(GRAY/ YELLOW) COMMON | AUX. CABLE ‘31’(BLACK/ WHITE) VOLUME- AUX. CABLE DOWN “30°(PINK/ YELLOW) AUX. CABLE *31’(BLACK/ WHITE) JAMMA ‘15’ JAMMA ‘A’ or ‘B’ or ‘e’ or ‘f? or ‘1’ or ‘2’ or ‘27’ or ‘28’ COMMON

Table 3: Test Bracket Wiring Chart Game Cartridge Installation

  • Install the four (4) mounting brackets to the underside of the “A” cartridge as shown in Figure 7.

Figure 7: Mounting Bracket Installation

  • Using the supplied wood screws, fasten the game cartridge case to the control panel shelf, as shown in Figure 8.

Figure 8: Case Mounting

  • Connect the JAMMA harness connector and the Auxiliary Cable connector to the “A’ cartridge. If your cabinet is equipped with Q-SOUND, also attach the audio cables.

6 [Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN=

Page 11

@AP@ON*co IN-oP, INC.

CAUTION

IMPROPER INSTALLATION OF THE JAMMA HARNESS TO THE GAME CARTRIDGE WILL CAUSE DAMAGE TO THE ENCLOSED PCB.

  • Power-up the game and set all operator adjustable options by pressing the TEST switch. Follow the instructions under the TEST MENU section of this manual.

Cabinet Decals & Marquee Installation

  • Install the new game marquee and and re-install its’ protective covering.
  • Peel-off the backing to the game instruction decal and place on the top of the monitor card. Also, apply the cabinet decals to both sides of the cabinet.

MARQUEE

MONITOR CARD

INSTRUCTION DECAL

Figure 9: Cabinet Decals X-MEN™ vs. STREET FIGHTER™

“B” KIT INSTALLATION

  • To install the cabinet graphics, you must follow the “FULL” Kit Preparation and Installation Procedure, steps 1 and steps 3 through 14.
  • To remove the existing “B” cartridge from the “A” cartridge, pull the old case clamps apart (see Figure 10). Carefully remove the old “B” cartridge and install the new “B’ cartridge. Re-install the case clamps.

Case Clamp

"A" Cartridge

Figure 10 : Case Clamp Installation

JAN WARNING DISASSEMBLY OF EITHER GAME CARTRIDGE WILL VOID YOUR WARRANTY.

  • Power-up the game and set all operator adjustable options by pressing the TEST switch. Follow the instructions under the TEST MENU section of this manual.

[Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM COIN-OP, INC, 7

Page 12

@ANPEON° coin-op, inc. X-MEN™ vs, STREET FIGHTER™

“E” KIT INSTALLATION

  • Remove the monitor glass and throughly remove the old game stickers from the monitor card or bezel. Peeloff the backing to the game instruction decal and apply to the top of the monitor card (bezel)
  • VERIFY that the existing control panel wiring conforms to the JAMMA configuration for this game , as shown in Tables | & 2 on page 5 of this manual. If any of the lower button wires are frayed or nicked, replace with new auxiliary cable (included in the kit).
  • To install the game cartridges, follow the Game Cartridge Installation instructions, steps 21 through 24, on page 6 of this manual.

“BE” KIT INSTALLATION

  • Remove the monitor glass and throughly remove the old game stickers from the monitor card or bezel. Peeloff the backing to the game instruction decal and apply to the top of the monitor card (bezel)
  • Follow the “B” KIT INSTALLATION instructions, steps 2 and 3, on page 7 of this manual.

8 [Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 13

@APEOM? coin-op, inc. X-MEN™ vs, STREET FIGHTER™

TEST MENU

The test menu allows you to test the functions and configure the game. These items include input devices such as joysticks, buttons and coin door or switches, output devices such as monitor, speakers and meters. Through the Test Menu you can also access the Configuration Menu, where you can change the settings of the game.

ACCESSING THE TEST MENU

© For a CAPCOM® cabinet, or a cabinet with a test switch: Make sure the game is on and push the test switch. The screen shown below will appear.

¢ For a cabinet without a test switch: Push the blue test switch on the outside of the black plastic casing (refer to the inside back cover of the manual).

TEST MENU

. INPUT

. OUTPUT

. SOUND & VOICE

}. COLOR

. DOT CROSS HATCH

  • GAME DATA

. CONFIGURATION

. MEMORY CHECK

  • EXIT

SELECT = 1P UP or DOWN START =1P SHOT1

SELECTING AN ITEM

© On the control panel, move the PLAYER I JOYSTICK (1P UP OR DOWN) to move the arrow in front of the desired item and then push the PLAYER I SHOT 1 (1P SHOT1) button, as shown below:

Player 1 Joystick Player 1 Start (ie Player 1 Shot 1 Player 1 Shot 2 vi601

[Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC. 9

Page 14

CAPCOM co-op, inc. X-MEN™ vs, STREET FIGHTER™

SELECTING AN ITEM (continued) © To return to the test menu, push the PLAYER I START (1P START) and PLAYER I SHOT 1 (1P SHOT1) buttons simultaneously. ° The test menu will return to the screen:

  • After you exit the “7. CONFIGURATION MENU” and
  • After the memory is tested from the menu, “8. MEMORY CHECK”.

CLOSING THE TEST MENU To close the Test Menu, highlight “9. EXIT” and push the PLAYER I SHOT 1 (1P SHOT1) button.

TEST MENU ITEM DESCRIPTIONS

INPUT Used to test all the input switches, such as joysticks and buttons. The “0” changes to a “1” as the button is pushed or joystick is moved. Check connections and switches in case the “0” doesn’t change to a “1” when depressed or moved.

Used to test the coin meter and the coin lock.

SOUND & VOICE Select a code of SOUND or VOICE with the PLAYER I JOYSTICK. Push the PLAYER I SHOT I button to hear the sound of the selected code.

COLOR Shows color bars of red, green, blue, and white. Adjust RGB and brightness to obtain the optimum color balance and solid black background.

DOT CROSS Used to test the screen size, focus and distortion. HATCH GAME DATA Coin méter and playtime information will be displayed.

CONFIGURATION _ | Used to change the game play settings. Refer to the CONFIGURATION MENU section. a MEMORY CHECK | Used to test memory. “OK” appears when each block of memory passes test, “NG” appears in case of malfunction. If “NG” appears, repeat the memory test and wait for the “OK” message. Contact your distributor if “NG” still appears.

Select this item and push the PLAYER I SHOT I (1P SHOT1) button to return to game play mode.

10 [Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 15

@AP@OM® coin-op, inc. X-MEN™ ys, STREET FIGHTER™

CONFIGURATION MENU

The Configuration Menu is used to change various game settings such as level difficulty, credits, sound configuration, etc. These settings are stored in memory on the PCB.

The Configuration Menu is divided into 2 sections. In the SYSTEM section, you can change credits, sound, and coin door configurations. In the GAME section, you can change the play difficulty level and duration of the game.

ACCESSING THE CONFIGURATION MENU . From the TEST MENU, move the arrow to “7. CONFIGURATION” and push the PLAYER 1 SHOT I button. The screen below will be displayed. A description of each option is explained in the table below.

. SYSTEM

. GAME

. DEFAULT

. SAVE & EXIT

P UP or DOWN

CONFIGURATION MENU ITEM DESCRIPTIONS

SYSTEM | Select this item to change settings for credits, monitor flip, sound and coin door configurations. GAME Select this item to change difficulty level, damage level, time count speed, maximum number of rounds and event type. DEFAULT | Use this item to restore configuration settings to the original factory values. Press the PLAYER I SHOT I and PLAYER I SHOT 2 buttons at the same time to restore default values. SAVE & | Use this to save new configuration settings and exit to the Test Menu. The message EXIT “SAVING NEW CONFIGURATION IN EEPROM” will appear while the new settings are being saved. DO NOT turn power off to the game until “SAVING” is complete and the Test Menu reappears.

[Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC. ll

Page 16

CAPEOM* coin-op, inc. X-MEN™ ys, STREET FIGHTER™

SYSTEM CONFIGURATION

CHANGING THE SYSTEM CONFIGURATION SETTINGS

Move the PLAYER I JOYSTICK up or down to highlight the desired option. Once the option is highlighted, move the PLAYER | JOYSTICK left or right or press the PLAYER 1 SHOT 1 button to select.

7-1. SYSTEM CONFIGURATION

  • COIN MODE 2 COINS 1 CREDIT

. CONTINUE ON

  • MONITOR NORMAL

}. DEMO SOUND ON

. SOUND MODE STEREO (QSOUND)

. CHUTE TYPE 2 CHUTES SINGLE

. EXIT

SELECT OPTION P UP or DOWN MODIFY SETTING = 1P LEFT or RIGHT = 1P SHOT1 or SHOT2

SYSTEM CONFIGURATION ITEM DESCRIPTIONS

  • COIN MODE SELECT THE CHARGE PER PLAY.
  • CONTINUE. SELECT ON FOR CONTINUOUS PLAY OR OFF FOR NON-CONTINUOUS PLAY.
  • MONITOR FLIPS THE POSITION OF THE SCREEN. IF THE SCREEN APPEARS UPSIDE-DOWN, CHANGE THE SETTING TO FLIP; IF THE SCREEN APPEARS CORRECT, SELECT NORMAL.
  • DEMO SOUND. TURNS ATTRACT SOUNDS ON OR OFF.
  • SOUND MODE SELECT STEREO OR MONAURAL FOR USE WITH YOUR CABINET.
NOTE: STEREO SHOULD ONLY BE SELECTED FOR USE WITH CAPCOM® QSOUND CABINETS. 6, CHUTE TYPE | SELECT THE NUMBER OF PLAYER(S) AND COIN CHUTE TYPE.
  • EXIT TO SAVE THE SETTINGS AND RETURN TO THE CONFIGURATION MENU, HIGHLIGHT THIS ITEM AND PUSH. EITHER THE PLAYER J SHOT] BUTTON OR THE PLAYER I SHOT 2_ BUTTON.

SYSTEM CONFIGURATION OPTION SETTINGS

1 CREDIT2 CREDITS:3 CREDITS4CREDITS5 CREDITS

6 CREDITS 9 CREDITS: 1 CRED} IT

3. COINS‘5 COINS7 COINS
1. CREDIT1 CREDITCREDIT.

8 COINS 9 COINS 2COINS START FREE PLAY 2 CONTINUE = or | oF | DEMO SOUND fe ON or

NOTE: FACTORY SETTING

12 [Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 17

CAP@OM® coin-op, Inc. X-MEN™ ys, STREET FIGHTER™

GAME CONFIGURATION

CHANGING THE GAME CONFIGURATION SETTINGS

Move the PLAYER J JOYSTICK up or down to highlight the desired option. Once the option is highlighted, move the PLAYER I JOYSTICK left or right or press the PLAYER 1 SHOT I button to select.

7-2. GAME CONFIGURATION

. DIFFICULTY EXPERT

. DAMAGE LEVEL NORMAL

. TIMER SPEED NORMAL

}. AUTOMATIC OFF

. JOIN-IN ON

. EVENT OFF

. GAME SPEED TURBO 2

. EXIT

SELECT OPTION P UP or DOWN MODIFY SETTINGS P LEFT or RIGHT = 1P SHOT1 or SHOT2

GAME CONFIGURATION ITEM DESCRIPTIONS

  • DIFFICULTY SETS THE DIFFICULTY LEVEL.
  • DAMAGE LEVEL SETS THE OFENSIVE POWER LEVEL
  • TIMER SPEED SETS THE SPEED OF THE COUNTDOWN FROM THE TIMER DISPLAY
  • AUTOMATIC SETS AN AUTOMATIC BLOCKING FEATURE FOR MOST CHARACTERS (SHOULD BE USED ONLY FOR BEGINNING PLATERS; NOT RECOMMENDED FOR MOST LOCATIONS).
  • JOIN-IN _| SETS THE OPTION TO ALLOW OTHER PLAYERS TO JOIN-IN. _|
  • EVENT TURNS ON EVENT MODE. USEFUL FOR CHAMPIONSHIP TOURNAMENTS. OFF: NORMAL SETTING. SETS THE MODE TO NORMAL OPERATION. 1 MATCH: MATCHES PLAYER WITH ONE CREDIT. A WIN OR A LOSS RESULTS IN GAME OVER (CONTINUE Is NOT AVAILABLE).
  • GAME SPEED SETS THE SPEED AT WHICH CHARACTERS FIGHT. FREE SELECT ALLOWS THE PLAYER TO SELECT THE. GAME SPEED.
  • EXIT RETURN TO THE CONFIGURATION MENU.

GAME CONFIGURATION OPTION SETTINGS

HARD 3 HARD 4 HARD 5 EXPERT.

HIGH MAXIMUM

FASTEST

NOTE: [_FACTORY SETTING

[Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC. 13.

Page 18

CAPCOM? coin-op, inc. X-MEN™ vs. STREET FIGHTER™

JAMMA Connections

SOLDER SIDE COMPONENT SIDE

Z o ; fa) Z i=] 4 Q)Q)| +5 VDC +5 VDC +5 VDC +5 VDC

+12 VDC +12 VDC

KEY7_|KEY

COIN COUNTER 1 COIN LOCK 2 COINLOCK 1 *SPEAKER (-) a *SPEAKER (+) :

VIDEO RED VIDEO BLUE VIDEO GROUND DIAGNOSTICS. 1 1 PLAYER - COIN [17 _|_1 PLAYER - START I PLAYER - UP 1 PLAYER - DOWN 1 PLAYER - LEFT 1 PLAYER - RIGHT 1 PLAYER - LIGHT PUNCH 1 PLAYER - MIDDLE PUNCH 1 PLAYER - HEAVY PUNCH VIDEO GREEN VIDEO SYNC SERVICE (FREE CREDIT) NK 2 PLAYER - COIN 2 PLAYER - START. 2 PLAYER - UP 2 PLAYER - DOWN 2 PLAYER - LEFT 2 PLAYER - RIGHT 2 PLAYER - LIGHT PUNCH 2 PLAYER - MIDDLE PUNCH 2 PLAYER - HEAVY PUNCH NIC NIC GND. GND fo} z\glalz fe} fo}

Q]O}Z/z ZIZIAIA.

WIRE COLOR CONNECTOR ODD ROW CONNECTOR EVEN ROW WIRE COLOR

NIC NIC

NICENIC
NICEoa]Nic
NICExemNIC
PURPLE/YELLOW_|PLAYER 2 HEAVY KICKENIC

NIC i NIC NIC PLAYER | HEAVY KICK PLAYER | MIDDLE KICK PLAYER 1 LIGHT KICK GRAY/YELLOW__| PLAYER 2 LIGHT KICK PINK/YELLOW PLAYER 2 MIDDLE KICK

NIC NIC

GRAY/YELLOWTEST BRKT-VOLUME UP:TEST BRKT-VOLUME DOWN_| PINK/YELLOW

BLACK/WHITE TEST BRKT-VOLUME COMMON_f

BLACKPLAYER 2 KICK - COMMONae#9PLAYER 1 KICK-COMMON

14 [Proprietary and confidential information,

Page 19

1-3/4" DRILL FOR JOYSTICK HOLE 1-3/16" DRILL FOR PLAYER HOLE

TRIM LINE (TYPICAL)

1-3/16" DRILL FOR BUTTON HOLES

CAPCOM , INC. i 3311 NORTH KENNICOTT RO tn. ARLINGTON HEIGHTS: ILLINOIS 60004

X-MEN -VS- STREET FIGHTER DRILL TEMPLATE

DATE: 09/16/96 DRAWN BY: JMA

1600100 REVISION NO:

Page 20

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 21

ONT'dO-NIOD @WODAYD 10808 {nOWHEA patos 20 pasoPsip oq 1 ou “WOReuZORN TeRUSpUOD pue Creat @IOH CNV SSHadHd ‘SWAIGOUd TONLNOD SWNTOA ONIONSTYSdXA TUV NOAA = “ALON ‘008006 (GNNOS 0 XO LNO OIGNY ATAVO ANVITIXAY WAWVE STOULNOD 3SV9 AWVD NOILLVIYOANI SONSYS43y

Page 22

NOTICE

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.

WARNING

Copyright © 1995 CAPCOM ® con-oP, INc., All Rights Reserved