CATHODE RAY TOMES

Water Ski

Water Ski (Taito Corporation, 1983) · Manual · 92 pages · 94 sections · original scan

Page 1

fon ive) w =

Page 2

Warranty

Your new Sega Product is covered for a period of 90 days from the date of shipment. This certifies that the Printed Circuit Boards, Power Supplies and Monitor are to be free of defects in workmanship or materials under normal operating conditions. This also certifies that all Interactive Control Assemblies are to be free from defects in workmanship and materials under normal operating conditions. No other product in this machine is hereby covered.

Sellers sole liability in the event a warranted part described above fails shall be, at its option, to replace or repair the defective part during the warranty period. For Warranty claims, contact your Sega Distributor.

Should the Seller determine, by inspection that the product was caused by Accident, Misuse, Neglect, Alteration, Improper Repair, Installation or Testing, the warranty offered will be null and void.

Under no circumstances is the Seller responsible for any loss of profits, loss of use, or other damages.

This shall be the exclusive written Warranty of the original purchaser expressed in lieu of all other warranties expressed or implied. Under no circumstance shall it extend beyond the period of time listed above.

Page 3

TABLE OF CONTENTS

INTRODUCTION OF THE OWNERS MANUAL

GENERAL PRECAUTIONS

NYNAURWNE . PRECAUTIONS TO BE HEEDED FOR OPERATION . NAME OF PARTS

. ACCESSORIES

. ASSEMBLY AND INSTALLATION

. PRECAUTIONS TO BE HEEDED WHEN MOVING MACHINE

. CONTENTS OF GAME

. EXPLANATION OF TEST AND DATA DISPLAY

7-1 POWER SUPPLY UNIT AND COIN METER

7-2: TEST MODE

7-3, MEMORY TEST

7-4 T.G.P. TEST

7-5 INPUT TEST

7-6 OUTPUT TEST

7-7 SOUND TEST

7-8 C.R.T. TEST

7-9 GAME ASSIGNMENTS

7-10 COIN ASSIGNMENTS

7-11 VOLUME SETTING

7-12 BOOKKEEPING

7-13 BACKUP DATA CLEAR

  • MAINTENANCE OF MECH UNIT 8-1 ADJUSTMENT AND REPLACEMENT OF SWING VOLUME

8-2 GREASING

  • COIN SELECTOR 10. PROJECTOR

10-1 CLEANING THE SCREEN,

10-2 MITSUBISHI MONITOR

. REPLACEMENT OF FLUORESCENT LAMP AND LAMPS

11-1 REPLACEMENT OF FLUORESCENT LAMP

. PERIODIC INSPECTION TABLE

. TROUBLESHOOTING

13-1 REPLACEMENT OF FUSES

. GAME BOARD

14-1 REMOVING THE IC BOARD 14-2 COMPOSITION OF THE GAME BOARD

. DESIGN RELATED PARTS

. PARTS LIST . WIRING DIAGRAMS 9-19

21~23

24~36

31~33

37~40

37~38

39~40

41~42

43~46

44~46

49~50

51~52

55~87

XXX

Page 4

SPECIFICATIONS

Installation space: 108 in.(L) x 53 in.(W)

Height: 90 in.

Weight: Approx. 871 lbs.

Power maximum current: 8 Amp AC 120V 60 Hz

MONITOR: 50 INCH PROJECTION DISPLAY

INTRODUCTION OF THE OWNERS MANUAL

SEGA ENTERPRISES, LTD., has for more than 30 years been supplying various innovative and popular amusement products to the world market. This Owners Manual is intended to provide detailed descriptions together with all the necessary installation, game settings and parts ordering information related to the SEGA WATER SKI, a new SEGA product.

This manual is intended for those who have knowledge of electricity and technical expertise, especially in ICs, CRTs, microprocessors, and circuit boards. Read this manual carefully to acquire sufficient knowledge before working on the machine. Should there be a malfunction, non-technical personnel should under no circumstances touch the interior system. Should the need arise, contact our main office, or the closest branch office listed below.

SEGA ENTERPRISES, INC. (USA) Customer Service 45133 Industrial Drive Fremont, CA 94538 Phone 650-802-1750 Fax 650-802-1754 7:30 am - 4:00 pm, Pacific Standard Time Monday thru Friday

Page 5

General Precautions

Follow Instructions: All operating and use instructions should be followed. Attachments: Do not use attachments not recommended by the product manufacturer as they may cause hazards. Accessories: Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use only mounting accessories recommended by the manufacturer. Moving the Product: This product should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product to overturn. Ventilation: Slots and openings in the cabinet are provided for ventilation, to ensure reliable operation of the product and to protect it from overheating; these openings must not be blocked or covered. The openings should never be blocked by placing the product in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

Power Sources: This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your location, consult your local power company. For products intended to operate from battery power or other sources, refer to the operating instructions. Grounding or Polarization: This product is equipped with a three-wire grounding-type plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug. Power Cord Protection: Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. Overloading: Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

Object and Liquid Entry: Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. Servicing: Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. Damage Requiring Service: Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

  • If the power cord or plug is damaged;
  • If liquid has been spilled, or objects have fallen into the product;
  • If the product has been exposed to rain or water;
  • If the product does not operate normally when following the operating instructions. Adjust only those controls that are explained in the operating instructions. An improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation;
  • If the product has been dropped or damaged in any way;
  • When the product exhibits a distinct change in performance; this indicates a need for service. Replacement Parts: When replacement parts are required , be sure the service technician has used replacements parts specified by the manufacturer or that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.
Page 6

Safety Check: Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. Heat: The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

Lithium Battery- Dispose of batteries only in accordance with the battery manufacturer’s recommendations. Do not dispose in an open flame condition, since the battery may explode. Cleaning: When cleaning the monitor glass, use water or glass cleaner and a soft cloth. Do not apply chemicals such as benzine, thinner, etc. Location: This an indoor game machine, DO NOT install it outside. To ensure proper usage, avoid installing indoors in the places mentioned below: + Places subject to rain/water leakage, or condensation due to humidity; In close proximity to a potential wet area;

  • Locations receiving direct sunlight;
  • Places close to heating units or hot air; eIn the vicinity of highly inflammable/volatile chemicals or hazardous matter;
  • On sloped surfaces; «In the vicinity of emergency response facilities such as fire exits and fire extinguishers;
  • Places subject to any type of violent impact;
  • Dusty places.

INSTALLATION PRECAUTIONS

  • Verify the amperage of the branch circuit outlet before plugging in the power plug. Do not overload the circuit.

+ Avoid using an extension cord. If one is required, use an extension cord of type SJT, 16/3 AWG rated min. 120 VAC, 7A.

  • Moving this unit requires a minimum clearance (of doors, etc.) of 32” (W) by 77” (H). ¢ For the operation of this machine, secure a minimum area of 32” (W) by 42”(D).

REGULATORY APPROVALS This game has been tested and found to comply with the Federal Communications Commission Rules. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This game has been tested and listed by Underwriters Laboratories, Inc., to ANSI/UL22.

LISTED

5K92

AMUSEMENT MACHINE

Page 7

. PRECAUTIONS TO BE HEEDED FOR OPERATION This product allows the game to be played by operating the SKATE BOARD. In order to prevent accidents, be sure to comply with the following points before and during operation.

PRECAUTIONS TO BE HEEDED FOR OPERATION BEFORE STARTING THE OPERATION

@ In order to avoid accidents, check the following before starting the operation: Check if all of the adjusters are in contact with the surface. If they are not, the cabinet can move and cause an accident.

WARNING! @ Check to see if hazard preventive parts are damaged or omitted. Operating the product with the hazard preventive parts as is left in an irregular status will cause accidents.

Ensure that all of the Adjusters are in contact with the floor.

Do not put any heavy item on this product. Placing any heavy item on the product can cause a falling down accident or parts damage. Do not climb on the product. Climbing on the product can cause falling down accidents. To check the top portion of the product, use a step. To avoid electric shock, check to see if door & cover parts are 508.5

To avoid electric shock, short circuit and or parts damage, do not put the following items on or in the periphery of the product:

Flower vases, flower pots, cups, water tanks, cosmetics, and receptacles/ containers/vessels containing chemicals and water.

To avoid injury, be sure to provide sufficient space by considering the potentially crowded situation at the installation location. Insufficient installation space can cause the player to come into contact with or hit the

CAUTION! others and result in injury or trouble.
Page 8

PRECAUTIONS TO BE HEEDED DURING OPERATION To avoid injury and trouble, be sure to constantly give careful attention to the behavior and manner of the visitors and players.

not allowed to play the game. > Intoxicated persons. W, G! > Pregant women or those who are in the likelihood of pregnancy. ARNING! > Those who need assistance such as the use use of apparatus when walking. > Those who have high blood pressure or a heart condition. > Those who have experienced muscle convulsion or loss of conciousness when exposed to intensive light stimulus due to watching television, playing video games or water surface flickering. > Persons susceptible to motion sickness. > Persons whose actions runs counter to the product’s warning displays. i @ To avoid injury and accidents, those who fall under the following catagories are

The player should be able to get on the skate board and hold on firmly to the safety bar. To avoid falling down accidents, instruct those who are shorter than 51 inches not to play, as the height of the saftey bar is approximately 51 inches.

Instruct those who wear high heel shoes to refrain from playing the game by explaining that playing game with highheeled shoes is very likle to cause potentially hazardous situation.

To avoid injury from potential falling down accidents, be sure to that only one person is allowed to play at a time.

Do not allow players to put any heavy items or beverages on the product. Falling items can cause accidents and spilled beverages can cause electric shock.

@ To avoid electric shock and short circuit, do not allow customers to put hands and fingers or extraneous matter in the openings of the product or small openings in or around the doors. @ To avoid falling down and injury resulting from falling down, immediately stop the customer’s leaning against or climbing on the product, etc. @ To avoid electric shock and short circuit, do not allow the customers to unplug the power plug without justifiable reason.

Page 9

A

CAUTION! Instruct the player to hold firmly to the Saftey Bar during game. Caution the customers who are most likely to cause injury by playing without holding the Safety Bar, for example.

To avoid injury, do not allow persons other than the player access to the mechanism base during game play.

Instruct the player to play by standing on both feet. Standing on one leg to play can cause injury.

Instruct the player not to put baggages, etc. on the mechanism base to avoid damaging such items.

Immediately stop violent acts such as hitting and kicking the product. Such violent acts can cause parts to be damaged or falling down, resulting in injury due to fragments and falling down.

Regarding this product, the weight of the player is limited to 330 Ibs. To avoid machine damage and injury due to machine damage, playing by those who are as heavy as 330 lbs. or heavier is strictly prohibited.

Page 10

2 .NAME OF PARTS

GAME SPECIFICATIONSWIDTHLENGTHHEIGHTWEIGHT

DURING SHIPPING 1525 LBS.

All measurements are in inches

REAR CABINET63”xX70”x58”675 LBS.
PTV55”x37.5”x17°462 LBS.
PTV BASE/BILLBOARD54”x48”Xx43.5”387 LBS.
BILLBOARD46"18”xWw33 LBS.
REAR CABINET53”x60.25”x48”416 LBS.
PTV46”xX22”x67”263 LBS.
PTV BASE47”Xx41”x31.5”159 LBS.
WHEN ASSEMBLED93”x108”x90”871 LBS.
Page 11

3 . ACCESSORIES

DESCRIPTION OWNERS MANUAL Part No. (Qty.) 4201-6334-01 (1)

Note Figures If Part No. has no description, the Number has not been. registered or can not be registered. Such a part may not be obtainable even if the customer desires to purchase it. Therefore, ensure that the part is in safekeeping with you.

FUSE LOCAL PURCHASE

4 Aslow blow 2 Aslow blow

2@5 A slow blow

7 Aslow blow

TOSHIBA Remote Control! for Projector Used for adjustment. See Sec. 12. 200-5536 (1)

| 0° ef 28:

0! @lelo/0 o o} ts @|0/@-/0 & 0: <> <j

gE bj

One of the above two types of Remote Controls is used for the Projector. KEY MASTER KEY 220-5576 (2) (2) pad Speningiclosing For the CASHBOX DOOR (== (=

VOL CONT B-5K OHM 220-5573 () 220-5484

MITSUBISHI Remote Control for Projector Used for adjustment. See Sec. 12. 200-5532(1)

Page 12

4 ..ASSEMBLING AND INSTALLATION

WARNING! Assembling should be performed as per this manual. Since this is a complex machine, erroneous assembling may cause damage to the machine, or malfunctioning to occur. When assembling, be sure to perform work by plural persons. Depending on the assembly work, there are some cases in which performing the work by a single person can cause personal injury or parts damage.

When carrying out the assembly work, follow the procedure in the following 6-item sequence:

ote that tl 1 | ASSY OF PTV

WIRING CONNECTIONS BETWEEN CABINETS

SECURING IN PLACE (ADJUSTER ADJUSTMENT)

POWER SUPPLY un) | BY] |} Ww] |] hm

TURNING POWER ON

6 | ASSEMBLING CHECK

e tools such as a phillips screwdriver and wrench for M16 hexagon bolt w/24 mm width across flats are required for the assembly work.

1 | assy oF PTV

When installing the billboard, it is difficult to carry out work by one person. To perform work properly and safely, be sure work is performed by at least two people.

To perform work safely and securely, be sure to prepare a step which is in a secure and stable condition. Not using a step or using an unstable step can cause a violent falling down accident.

Page 13

By using the specified screws, secure the 2 Mask Holders t 0 the Projection Display ceiling. (Fig. 4.1a)

Q@) Insert the TV Mask from the underside as shown and secure with a total of 6 screws.

  • While supporting the Billboard by 2 persons, another person using a step is to insert the Billboard Connector into the Terminal Board of Projection Display ceiling. (Fig. 4.1b)
  • Insert the Billboard From the front as shown and secure with 2 screws (Fig. 4.1a)

t @ BILLBOARD

. SCREW (2), M5x16 w/flat & spring washers, black

PROJECTION DISPLAY

@ BILLBOARD'S Connector te

@ SCREW Q),M5x25 One each on both sides using flat washer, chrome

M4x14 (2) for each

@ TVMASK / SCREW (4),M5X20 w/flat & spring washers

FIG. 4.1a FIG. 4.1b

Page 14

©) In order to prevent accidents during assembly

work, have all of the leg adjusters of the PTV Base make contact with the surfaces to secure the PTV Base.

©) Mount the assembled PTV on the PTV Base. After mounting the PTV, move it to the rear part of the PTV Base. When performing this work, be sure to use 4 or more persons.(Fig. 4.1c)

Fig. 4.1¢

©) Connect the wires wired to the PTV Base to the PTV Connector Panel. Insert the wiring connectors, each of which wire covering is red, green, and blue, to the corresponding one of R.G.B. terminals as per connector panel display inside the PTV, and insert the remianing wire connector to the SYNC terminal. The connector’s insertion angle is predetermined. Inserting the connector in a forcible manner will damage the connector. Check for the correct inserting direction and then insert the connector. After insertion of the connector, turn the connector’s ring clockwise to lock the connection.

MITSUBISHI PTV

Fig. 4.1d

CONNECTOR PANEL

The connector panel has 3p white connector in addition to the connectors displayed as R.G.B. and SYNC. Connect the wiring coming from the PTV Base power supply unit to the 3p white connector.

Page 15

Q) Temporarily fasten the PTV Holders to the PTV

Base with a screw for each Holder (Fig. 4.1e)

Fig. 4.le PTV HOLDER

TRUSS SCREW

  • for each M5x25, chrome

Secure the Front Panel to the front of the PTV with 4 screw: 's. At this time, by using the underside 2 screws, tighten together with the PTV Holder. (Fig. 4.1f)

TRUSS SCREW

  • chrome M5x25, using flat washer Fig. 4.1f

FRONT PANEL

Page 16

2 WIRING CONNECTIONS BETWEEN THE CABINETS

FRONT CABI ASSY TUBE REAR CABI

Fig. 4.2a

Install the ASSY TUBE to the Front Cabinet which is assembled as per | 1 |and the Rear Cabinet, and perform wiring connection in between both cabinets.

@ The ASSY TUBE’s box side is to the Front Cabinet. @ Secure the box to the Front Cabinet with 4 screws. Connect all of the wiring connectors coming from at this time, be very careful so that wires are not the Front Cabinet and the box side wiring connec- caught and damaged. tors. Be sure to connect the connectors of identical (Fig. 4.2b) color and number of pins.

©) Connect all of the Rear Cabinet side Wiring Oo) By using the 4 screws, secure the ASSY Tube Connectors and ASSY Tube Wiring Connectors. Plate parts to the Rear Cabinet. At this time, use Ensure that connectors of identical color and care so that wirings are not caught and damaged. number of pins are connected with each other. (Fig. 4.2c)

Page 17

3 SECURING IN PLACE (ADJUSTER ADJUSTMENT)

Be sure to have all the Adjusters make contact with the surface. Unless the Adjusters come into contact with the surface, the Cabinet

WARNING! can move of itself, causing an accident.

This machine has 8 each of casters and adjusters (FIG. 3. 2 a). When the installation position is determined, cause the adjusters to come into contact with the floor directly, make adjustments in a manner so that the casters will be raised approximately 5mm. from the floor and make sure that the machine position is level.

Q@ Move the machine to the installation position.

Cause all of the leg adjusters to make contact with the floor. By using a wrench, make adjustments in the height of the leg adjusters to ensure that the machine's position is level.

After making adjustments, fasten the leg adjuster nut upward and secure the height of the leg adjuster.

Fig. 43a

Y Fig. 4.3b

Page 18

@) Depending on the floor surface status of the installation location, the Rear Cabinet may move of itself. As shown, the NON-SLIP SHEET is attached to the back side of the CUATION MAT. Ensure that the Adjuster is installed in the manner to match the position of NON-SLIP SHEET

Adjuster position (4 places)

ADJUSTER

c CAUTION MAT (SPW-0001) “— NON SLIP SHEET (ASK-0006) FLOOR

CASTER

FASTEN UPWARDS

Approx. 1/4” INCH

Ventilation Space Approximately [5 cm.

m= zi \ WHOA ‘Approx. 10cm Refer to this Fig, (Scale:1/100) for the layout of the place of installation. Provide sufficient space so as to allow for ventilation by the ventilation fan. Provide space approximately 10cm. between the Front Cabinet and the Rear Cabinet.

Page 19

4 | PowER SUPPLY

@ Ensure that the power cord is not exposed on the surface (passage, etc.). If exposed, they can be caught and are susceptible to damage. If damaged, the cord can cause an electric shock or short circuit. Ensure that the wiring position is not in the customer's passage way

WARNING! or the wiring has protective covering.

The AC unit is mounted on the left side of Front Cabinet DX. The AC Unit incorporates the Main SW, Earth Terminal and Inlet. Firmly insert the Power Plug into the Socket Outlet and the other side of the plug to the Inlet. Turn the Main SW ON to turn power ON.

® Ensure that the Main SW is OFF.

MAIN SW

WA fo) : ° POWER CORD {LJ} = >

MAIN SW is OFF. ° °

Fig. 4.4a

Page 20

5 TURNING POWER ON

To turn power on, turn the AC Unit’s Main SW on. The Billboard’s Fluorescent Lamp lights up and images will be outputted on the projector. The lamps on the right sides of the Coin Chute Tower alternate lighting up by halves. Background music (BGM) is outputted during ADVERTISE from the speaker. However, this BGM is not emitted if “No BGM output during ADVERTISE” is set. Since the Skate Board is locked unless the game is started, it can not be moved in the right/left directions.

Page 21

ASSEMBLING CHECK

Va

<ROM> Ic 15 Ic Ic 9 Ic7 Ics <RAM> Ic 58 Ic 63 Ic 79 Ic 109 Ic 16 Ic 95 IC 86 Ic 12 Ic 10 Ic Ic 82 Ic 61 Ic 81 coop Goop GooD GooD GooD

coop GooD GooD GooD Goop GooD oop GooD Goop GooD GooD GooD oop MEMORY TEST

Ic 16 Ic 12 Ic 10 Ic 8 Ics

Ic $4 Goop Ic 71 GooD Ic 73 GOoD Ic 101 GooD Ic 114 GooD Ic 87 GOOD Ic 94 GooD Ic 10 GooD Ic 102 Good Ic 103 GOOD Ic 75 GOOD Ic 69 Goo Ic ss GOOD coop GooD GooD GooD GooD

cn coop

Ic 115 Goop

Ic 100 Ieu Ic 95 Ic 97 Ic 68 Ic 76 Ic 54 0 Good Goop GooD GooD GooD coop coop

PRESS TEST BUTTON TO EXIT Ic 78

Ic 3

Ic9 IC 88 Ic 89 Ic 60 Ic 83 \

Goop

coop

coop GooD coop Goop coop

/ Ne

ya INPUT TEST

SLIDE

PITCH LEFT PITCH RIGHT

SELECT (UP) SET SELECT (DOWN)

COIN CHUTE#I COIN CHUTE#2

SERVICE TEST 80H

OFF OFF

OFF OFF OFF

OFF OFF

OFF OFF

PRESS TEST BUTTON TO EXIT SN

/ Ne

?

\ ‘OUTPUT TEST

SELECT LAMP (UP) SET LAMP OFF OFF SELECT LAMP (DOWN) OFF

SLIDE LOCK

>EXIT

PRESS TEST BUTTON TO EXIT OFF S

/ Selecting the MEMORY TEST on the test mode menu screen causes the on-board memory to be tested automatically. The game board is satisfactory if the display beside each IC No. shows GOOD.

Selecting the INPUT TEST on the menu screen in the test mode to display the screen on which each SW and Volume is tested. Press each switch. (To check the Coin SW, insert a

Coin from the inlet with the Coin Chute Door being opened.) If the display beside each switch is ON, the switch and wiring connection are satisfactory. Check the display of each Volume value. The Volume could have an irregularity caused by differences between machines and vibration during transportation. Set the Volume values by referring to Section ?

In the output test mode, carry out lamp test to ascertain that each lamp lights up satisfactorily.

Page 22

a SOUND TEST

No (o)

SELECT WITH SERVICE BUTTON PRESS TEST BUTTON TO EXIT

( CRILTEST 12 mm MMMM a

KS PRESS TEST BUTTON TO CONTINUE

wt

ORE AT By In the TEST mode, selecting SOUND TEST causes the screen, on which sound related BD and wiring connections are tested, to be displayed. be sure to check if the sound is satisfactorily emitted from each of speaker and the sound volume is appropriate.

In the TEST mode menu, selecting C.R.T. TEST allows the screen (on which the projector is tested) to be displayed. Although the projector adjustments have been made at the same time of shipment from the factory, color deviation, etc., may occur due to the effect caused by geomagnitism, the location building’s steel frames and other game machines in the periphery. By watching the test mode screen, make judgement as to whether an adjustment is needed. If it is neccessary, adjust the projector by refering to Section 9.

Perform the above inspections also at the time of monthly inspection.

Page 23

5 .PRECATIONS TO BE HEEDED WHEN MOVING THE MACHINE

WARNING!

AN

CAUTION! @ When moving the machine, be sure to pull out the plug from the power supply. Moving the machine with the plug as is inserted can damage the power cord and cause a fire or electric shock. @ When moving the machine on the floor, retract the Adjusters and ensure that Casters make contact with the floor. During transportation, pay careful attention so that Casters do not tread power cords. Damaging the power cords can cause an electric shock and/or short circuit. @ When lifting the cabinet, be sure to hold the catch portions or bottom part. Lifting the cabinet by holding other portions can damage parts and installation portions, due to the empty weight of the cabinet, and cause personal injury.

Use care when handling glass made parts. When the glass is damaged, fragments of glass can cause injury

Do not push PTV from the rear side. Pushing the PTV from the rear side can cause the PTV to fall down. Push it from the side.

Where there are steps (or step-like differences in grade), move the machine by separating into each unit.

Page 24
  • CONTENTS OF GAME

The following explanations apply to the case the product is functioning statisfactorily. Should there be any moves different from the following contents, some sort of faults may have occurred. Immmediatly look into the cause of the fault and eliminate the cause thereof to ensure satisfactory operation

HOW TO PLAY

@) Put your feet on the Foot Controller.

@ Facing the Projector screen, the Coin Chute Tower is on the right-hand side. Insert one play worth of coins to have the Character selection screen appear. Up to 9 credits can be counted at one time. Coins inserted after counting 9 credits are not counted, nor returned

©) In the Character selection mode, the on-screen player character is selected. Press either of the Panel’s left/right blue Select Buttons to select the desired player and press the center Red Button to decide. Four Characters are available for selection.

2) The Course Select Mode follows the character

select/SET. As in the Character Select, press either of the left/right Blue Buttons to select a course and decide the selection by pressing the Center Red Button. The Courrses available for

selection are 3 types.

«COURSE SELECT MODE) SOURSE'SELECL PALM BEACH for Beginners This course represents the image of a southwestern ¥ [Beginner] 4 resort. H PALM BEACI course image Advanced} PAU-PAU RIVER for Advanced players PAURAURIVES Represents the jungle course as in the Amazon.

Expert

WHALE PARK WHALE PARK for Expert players A water course in an amusement park.

Select SET Select

Page 25

©) In the Character Select Mode and Course Select Mode, the remaining time for selection is displayed on the upper right-hand portion of the screen. Failing to press the Select Button within the time limit cuases “TAKUTO” and PALM BEACH to be automatically selected for the character and the course (for beginers) respectively.

© In the Character Select Mode and Course Select Mode, the remaining time for selection is displayed on the upper right-hand portion of the screen. Failing to press the Select Button within the time limit cuases “TAKUTO” and PALM BEACH to be automatically selected for the character and the course (for beginers) respectively.

Slide lefvright and tum. Jump by standing on tiptoes.

> Sliding the Foot Controller left/right cuases the on-screen player to turn left/right so as to correspond to the Controller movement. > At the Ramp, jump by moving the Foot pedal with heels up. Taking off at the end of the Ramp will extend the flying (jump) distance. > While jumping, jump action can be determined by moving the Foot Pedal. > Jump Action commands are as follows.

COMMAND JUMPING FROM FRONT HALF OF RAMP |JUMPING FROM REAR HALF OF RAMP (less flying distance) (longer flying distance)

(LP+LP Daffy Daffy Twister

Twister Twister spread Double somersault Double front flip roll Helicopter 720 Double back roll twist Somersault Front flip roll Helicopter 360 Back roll twist LS+RS

*LP: Left foot pitch *RP: Right foot pitch *LS: Left slide

*RS: Right slide *+: Continuous input *&: Simultaneous input

Page 26

@) A gate is provided in between the courses.Passing the gate within the time limit allows the remaining time to be extended and game play to continue.

At the Ramp, jump with Foot Pedal’s heels up. while jumping, use the Foot Controller to cuase the jump action to be activated. Depending on the jump flight distance and the type of jump action, the points the player can earn will be variable. The points awarded to the player will affect the after-course finish ranking.

® When remaining time limit elapses while the player is in the middle of the course, or when he finishes the course, the game is over. At the time of finishing the course, the ranking and the level will be determined on the points earned by the jump action. If the ranking position is 100th or higher, the player can enter his name.

ail YOUR POINTS

PALM BEACH 70 1500 pts

YOUR RANK

95/100

After finishing the game, the Foot Controller is locked.

oO) After one game is finished, if there remian one play worth of credits, the Character Select mode appears on the screen.

Page 27

. EXPLANATION OF TEST AND DATA DISPLAY

By operating the switch unit, periodically perform the tests and data check. When installing the machine initially or collecting cash, or when the machine does not function correctly, perform checking in accordance with the explanations given in this section. The following shows tests and modes that should be utilized as applicable.

TABLE 7 EXPLANATION OF TEST MODE

ITEMS DESCRIPTION SECTIONS

When the machine is installed, perform the following: INSTALLATION | |. Check to see that each setting is as per standard setting made 7-9, 7-10 OF MACHINE at the time of shipment.

2.In the INPUT TEST mode, check each SW and VR. 7-5

  • In the OUTPUT TEST mode, check each of lamps. 7-6
  • In the MEMORY TEST mode, check ICs on the IC Board. 7-3,7-4

MEMORY Choose MEMORY TEST in the MENU mode to allow the MEMORY test to be performed. In this test, PROGRAM RAMs, ROMs, and ICs on the IC Board are checked.

PERIODIC Periodically perform the following: SERVICING

  • MEMORY TEST 7-3,7-4
  • Ascertain each setting. 7-9,7 -10
  • In the INPUT TEST mode, test the CONTROL device 7-5
  • In the OUTPUT TEST mode, check each of lamps. 7-6

CONTROL 1. In the INPUT TEST mode, check each SW and VR. 7-5 SYSTEM

  • Adjust or replace each SW and VR. 8

3If the problem can not be solved yet, check the CONTROL’s moves. 8

PROJECTOR In the PROJECTOR ADJUSTMENT mode, check to see if the PROJECTOR adjustment is appropriately made. 7-8

IC BOARD 1. MEMORY TEST

  • In the SOUND TEST mode, check the sound related ROMs. 7-7

DATA CHECK Check such data as game play time and histogram to adjust the 7-12 difficulty level, etc

Page 28

7-1 SWITCH UNIT AND COIN METER

Never touch places other than those specified. Touching places not d can cause electric shock and short uit.

IMPORTANT! @ Adjust to the optimum sound volume by considering the environmental requirements of the installation location. @ If the COIN METER and the game board are electrically disconnected, game play is not possible.

Open COIN CHUTE DOOR, and the switch unit shown appears. The functio n of each switch is as follows:

SOUND VOLUME TEST BUTTON SWITCH UNIT SERVICE BUTTON

(@) SOUND VOLUME Controls of the rig! coin chute

(2) TEST BUTTON (TEST SW)

the speaker volume O oO

ht/left speakers on the le tower. Ena ‘SERVICE Test

For the handling of the TEST BUTTON, Fig. 7.1 refer to the section on test mode.

©) SERVICE BUTTON (SERVICE SW)

Gives credits without registering on the coin meter.

COIN METER

Open Cash Box Door and the Coin Meter will appear. The

Coin Meter counts the

number of coins inserted

Fig. 7.2

Page 29

7-2 TEST MODE This mainly checks if the operation of the game BD is accurate, and allows for COIN ASSIGNMENTS/GAME ASSIGNMENTS setting and Projector adjustments. (—

TGP.T

INPUT

CRI

>EXIT GAME ASS TEST MODE,

MEMORY TEST

EST

TEST

OUTPUT TEST

SOUND TEST

SNMENTS,

COIN ASSIGNMNETS

BOARD SETTING

BOOKKEEPING

BACKUP DATA CLEAR ~\

FIG. 7.2 TEST MENU

7-3 MEMORY TEST

Va

<ROM> Ic 1s. GooD Ic 1 Goop Ic 9 Goop Ic 7 Goop Ic 5 Goop <RAM> IC 58 GOOD IC s4 IC 63 GOOD IC 71 Ic 7 Good Ic 73 IC 109 GOOD IC 101 IC 116 GOOD IC 114 IC 95. GOOD IC 87 IC 8% GOOD IC 94 Ic 12 GOOD IC 10 IC 110 GOOD 1¢ 102 IC 11 GOOD IC 103 Ic 2 GOOD IC 75 IC 61 GOOD IC 69 Ic 81 GOOD Ic 55 MEMORY TEST

Ic 16 GOOD Ic 12, GooD Ic 10 GooD Ic 8 GooD Ic 5 Goop

coop 1c 2 Goop Goop Goop Good IC 115 Goop Good IC 100 Goo Ic 11 GOOD IC 95 Goop 1 97 GOOD IC 68 Good IC 76 Good IC s4 Goop

Goop

Goop GooD oop Goop Goop Goop Goop

XS PRESS TEST BUTTON 0 EXIT

Ic 78

Ic3

Ic9 Ic 88 Ic 89 Ic 60 Ic 83 a

Goop

Goop

coop coop Goop Goop Goop

FIG. 7.3 MEMORY TEST

7-4 T.G.P. TEST

Va

NS TGP. TEST

Ic 25 coop Ic 3 GooD

PRESS TEST BUTTON TO EXIT ~

  • Push the TEST BUTTON to cause the following TEST MENU to appear:

(2) By pushing the SERVICE BUTTON, bring the

“>” mark to the desired item and press the

TEST BUTTON. This will select the item’s

test.

‘S) After the test is complete, move the “>” mark to “EXIT” and press the TEST BUTTON to

return to game mode.

The MEMORY TEST mode is for checking the on-BD memeory IC functioning. “GOOD” is displayed for normal ICs and “BAD” is displayed for abnormal ICs

@ When the test is completed, if the display is as shown left, it is satisfactory.

@ After finishing the test, pressing the TEST BUTTON allows the

MENU MODE to return on the

screen.

IF THE TEST TIME FOR THE MEMORY TEST

EXCEEDS 5 MINUTES THE IC BOARD MAY BE

DEFECTIVE.

Selecting T.G.P. TEST cuases the functioning of the on-IC-BD T.G_P. (screen display related IC’s) to be checked automatically. If the IC is satisfactory, “GOOD” will be indicated and if the IC is not satisfactory, “BAD” will be displayed.

Page 30

7-5 INPUT TEST

When INPUT TEST is selected, the MONITOR will show the following, allowing you to watch the status of each switch and the value of each VR. of the cabinet to be viewed On the screen, periodically check the status of each switch & VR.

(

Ne SLIDE 80H

PITCH LEFT OFF PITCH RIGHT OFF

SELECT (UP) OFF SET OFF SELECT (DOWN) OFF

COIN CHUTE#I OFF COIN CHUTE#2 OFF

SERVICE OFF TEST OFF

PRESS TEST BUTTON TO EXIT TS

FIG. 7.5 INPUT TEST By pressing each switch, if the display on the right-hand side of the name of each switch changes to ON from OFF, the SW and the wiring connections are satisfactory. PITCH refers to the Switch for the left/right Foot Pedal’s UP/ DOWN. Normally, this is ON and stepping on the Pedal’s front side causes the Switch to become off.

Press the TEST BUTTON to have the menu mode return on the screen. Using the Decision (SET) button instead of TEST BUTTON will not allow for exiting from the Input Test Mode. Press the SET BUTTON and SELECT BUTTON (UP). By opening the Coin Chute Door, insert a coin from the Coin Inlet to check the Coin Chute Tower.

Page 31

7-6 OUTPUT TEST

Choose OUTPUT TEST to cause the following lower screen to appear. In this test, check the status of each lamp.

a ourenns > r ) Pressing the TEST BUTTON causes “ON” to be displayed and the corresponding lamp lights up. Pressing the TEST BUTTON again cuases “OFF” to be displayed and the lamp goes off. The Foot Controller is SETIAMB OF locked with the Slide Lock in the ON status, and SEEECTEAMP@OWN): OFF Unlocked to become free with the Slide Lock in the OFF status. SLIDE LOCK orr r ) Press the test Button to return to the MENU MODE.

>EXIT

FIG. 7.6 OUTPUT TEST

Page 32

7-7 SOUND TEST

Va

XX No (0)

>EXIT

SELECT WITH SERVICE BUTTON

PRESS TEST BUTTON TO EXIT wy,

FIG. 7.7 SOUND TEST

7-8 CR.T. TEST

o

\ CRITEST 1/2

WM YA

WHITE

PRESS TEST BUTTON TO CONTINUE =

T[ByTTON TO EXIT vy FIG. 7.8 C.R.T. TEST This enables sound used in the game to be checked. Sound related memory and each speaker are checked.

Press the SERVICE BUTTON to bring the arrow to the desired sound item to be tested. SE refers to sound effects and BGM refers to background music.

Each time the SERVICE BUTTON is pressed, the numeral displayed on the screen counts up and sound is admitted.

Bring the “>” to EXIT and press the TEST BUTTON to return to the MENU MODE.

Select C.R.T. TEST to cause the MONITOR to display the screen shown left, allowing MONITOR adjustment status to be checked.

Periodically check the MONITOR adjustment status on this screen.

The screen (1/2) enables color adjustment check to be performed. The color bar of each of the 4 colors, i.e..red, green, blue, and white, is the darkest at the extreme left and becomes brighter towards the extreme right.

Press the TEST BUTTON to shift to the next screen (2/2).

The screen (2/2) allows screen size and distortion to be tested.

Check if the CROSSHATCH FRAME LINE goes out of the screen and if the crosshatch lines are distorted.

Press the TEST BUTTON to return to the MENU mode. (FIG. 6.2)

Page 33

7-9 GAME ASSIGNMENTS

Selecting the GAME ASSIGNMENTS in the MENU mode causes the present game settings to be displayed and also the game settings changes (game difficulty, etc.) can be made. Each item displays the following content.

SETTING CHANGE PROCEDURE

Gror Setting changes cannot be stored unless the TEST BUTTON is pressed

while the arrow is on EXIT. PORTANT!

Press the SERVICE BUTTON to move the “>” to the desired item.

Choose the desired setting change item by using the TEST BUTTON.

©) To return to the MENU mode, move the arrow to EXIT and press the TEST BUTTON.

GAME ASSIGNMENTS \ @ ADVERTISE SOUND aaDIRCae, BOKMAL Determines wether ADVERTISE SOUND is to EXIT be emitted or not by the setting to ON when emitting it and to OFF when not emitting it.

@ GAME DIFFICULTY COUNTRY TYRE: seve Sets the Game Difficulty in 8 catagories from 1 to

  • The greater the number is, the higher the difficulty level becomes.

SELECT WITH SERVICE BUTTON YS AND PRESS TEST BUTTTON /)

The Following FIGURES/TABLES show the factory recommended settings.

Page 34

7-10 COIN ASSIGNMENTS

The “COIN ASSIGNMENTS” mode permits you to set the start number of credits, as well as the basic numbers of coins and credits. This mode expresses “how many coins correspond to how many credits.”

SETTING CHANGE PROCEDURE

PORTANT!

Gror Setting changes cannot be stored unless the TEST BUTTON is pressed

while the arrow is on EXIT.

  • Press the SERVICE BUTTON to move the arrow to the desired item. @ Choose the desired setting change item by using the TEST BUTTON.

@ To return to the MENU mode, move the arrow to EXIT and press the TEST BUTTON.

ya

\ COIN ASSI IGNMENTS \

COINCHUTETYPE COMMON @ COIN CHUTE TYPE

CREDET TO: SINET bepcnaneninad Sets the combination of the number of COIN CHUTEs and CREDITTO CONTINUE 1 CREDIT the number of players as applicable. In the case that the COIN CHUTE is changed, be sure the setting is made in a CHUTE COIN J.GREDI manner meeting the replaced coin chute. COINICREDIT SETTING #1

COMMON: Coins are accepted in common for both players. CHUTEM2 =1COIN I CREDIT

MANUAL SETTING INDIVIDUAL: >EXIT Each player uses a coin chute which accepts coins independently.

SELECT WITH SERVICE BUTTON

AND PRESS TEST BUTTON y,

@ CREDITTO START Number of credits required for starting game (1~5 credits are selected.)

@ CREDITTO CONTINUE Number of credits required for continuing game (1~5 credits are selected.)

@ = COIN/CREDIT SETTING Sets the CREDITS increase increment per coin insertion. There are 27 setings from #1 to #27, expressed in XX CREDIT as against XX COINS inserted. (TABLE 7.9a, 7.9b) #27 refers to FREE PLAY. When the COIN CHUTE TYPE is set to INDIVIDUAL, there are some setting numbers not displayed as indicated in TABLE 7.9b.

@ MANUAL SETTING This allows credit increase setting as against coin insertion to be further set in the manner finer than COIN/ CREDIT SETTING (refer to TABLE 7.9c).

Page 35

TABLE 7.10a COIN/CREDIT SETTING (COIN CHUTE COMMON TYPE)

SETTING FUNCTIONING OF CHUTE#1

SETTING #11 COIN1 CREDIT.
SETTING #21 COIN2 CREDITS
SETTING #31 COIN3 CREDITS
SETTING #41 COIN4 CREDITS
SETTING #51 COIN5 CREDITS
SETTING #61 COIN2 CREDITS
SETTING #71 COIN5 CREDITS
SETTING #81 COIN3 CREDITS
SETTING #91 COIN4 CREDITS
SETTING #101 COIN5 CREDITS
SETTING #111 COIN6 CREDITS
SETTING #122 COINS1 CREDIT.
SETTING #131 COIN1 CREDIT.
SETTING #141 COIN2 CREDITS
SETTING #151 COIN1 CREDIT

2 COINS 3 CREDITS

SETTING #161 COIN3 CREDITS
SETTING #173 COINS1 CREDIT.
SETTING #184 COINS1 CREDIT.
SETTING #191 COIN1 CREDIT

2 COINS 2 CREDITS 3 COINS 3 CREDITS 4 COINS 5 CREDITS

SETTING #201 COIN5 CREDITS
SETTING #215 COINS1 CREDIT.
SETTING #221 COIN2 CREDITS
SETTING #232 COINS1 CREDIT

4 COINS 2 CREDITS 5 COINS 3 CREDITS

SETTING #241 COIN3 CREDITS
SETTING #251 COIN1 CREDIT

2 COINS 2 CREDITS 3 COINS 3 CREDITS 4 COINS 4 CREDITS 5 COINS 6 CREDITS

SETTING #261 COIN1 CREDITS

SETTING #27 FREE PLAY

Page 36

MANUAL SETTING __|

COIN TO CREDIT

BONUS ADDER

COIN CHUTE #1 MULTIPLIER

  • COIN COUNTS AS 1 COIN cON 1203 cREDIT 102003

COIN CHUTE #2 MULTIPLIER

L.COIN COUNTS AS 1 COIN

CON 1203 CREDIT 100203

>EXIT MANUAL SETTING

1COIN 1 CREDIT

NO BONUS ADDER

‘SELECT WITH SERVICE BUTTON

AND PRESS TEST BUTTON

wy, FIG. 7.10b MANUAL SETTING

@ Determines Coin/Credit setting.

@ This sets how many coins should be inserted to obtain one Service Coin. Selecting MANUAL SETTING in the COIN ASSIGNMENTS mode displays the following screen. )--0

@ This sets how many tokens one coin represents.

Table 7.10e MANUAL SETTING

COIN TO CREDIT 1 COIN 1 CREDIT 2 COINS 1 CREDIT. 3 COINS 1 CREDIT 4 COINS 1 CREDIT 5 COINS 1 CREDIT 6 COINS 1 CREDIT 7 COINS 1 CREDIT 8 COINS 1 CREDIT 9 COINS 1 CREDIT

BONUS ADDER NO BONUS ADDER 2 COINS GIVE 1 EXTRA COIN 3 COINS GIVE 1 EXTRA COIN 4 COINS GIVE 1 EXTRA COIN 5 COINS GIVE 1 EXTRA COIN 6 COINS GIVE 1 EXTRA COIN 7 COINS GIVE 1 EXTRA COIN 8 COINS GIVE 1 EXTRA COIN 9 COINS GIVE 1 EXTRA COIN

COIN CHUTE MULTIPLIER 1 COIN COUNTS AS 1 COIN 1 COIN COUNTS AS 2 COINS 1 COIN COUNTS AS 3 COINS 1 COIN COUNTS AS 4 COINS 1 COIN COUNTS AS 5 COINS 1 COIN COUNTS AS 6 COINS 1 COIN COUNTS AS 7 COINS 1 COIN COUNTS AS 8 COINS 1 COIN COUNTS AS 9 COINS

Page 37

7-11 VOLUME SETTING

This allows Slide Volume to be set.

VOLUME SETTING

SLIDE MAX 77 (D0) MIN 77 (17) NEU 77 (77)

>CANCEL & EXIT SET & EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

Fig. 7.11 VOLUME SETTING

Stop at the center position after fully swinging the Foot Controller right and left.

SLIDE SETTING

After swinging the Foot Controller fully to the left and right, return to the nuetral position. Selecting SET & EXIT with the Foot Controller as is in the muetral position causes the currently executed setting to be stored and the TEST MENU mode returns to the screen. If CANCEL & EXIT is selected, the present setting will not be stored and teh previously set value (in parenthesis) will remain.

Page 38

7 - 12 BOOKKEEPING

Choosing BOOKKEEPING in the MENU mode displays the data of operating status up to the present are shown on 2 pages. Press the TEST BUTTON to proceed to PAGE 2/2.

BOOKKEEPINGTAGEI@COIN CHUTE#*:

COIN REPORT Number of coins put in each Coin Chute.

COIN CHUTE #1 ceaveneor oocoontes Total number of activations of Coin Chutes

com cm: #2x@TOTALCOINS:
ceaveneoroocoontesTotal number of activations of Coin Chutes.

SERVICE CREDITS XXXXXXXXXXX

oesees1@com crept:
1 PGAMESXXXXXXXXXXKNumber of credits registered by inserting coins.

2P GAMES XXXXXXXXXXX NUMBER OF CONTINUE

ee@SERVICE CREDITS:

“es Credits registered by the SERVICE BUTTON.

TOTALTIME,XDXXHXXMXXS
LONGEST PLAYTIMEXXMXXSTotal number of credits (COIN CREDITS+SERVICE
SHORTETEST PLAYTIMEXXMXXSCREDITS).

\ PRESS TEST RUTTON TO CONTINUE y, @ TOTAL TIME: FIG. 7.12a BOOKKEEPING (1/2) The total energized time.

/ BOOKKEEPING PAGE 2/2 \ TIME HISTOGRAM OMO0S ~ 0M29S (OM30S ~ 0M39S M408 ~ oM49S (OMSOS ~ OMS9S XXXXXXXX IMO0S ~ IMO9S XXXXXXXX IMI0S ~ IM19S 1M20! IM30! On page (2/2), each play frequency is displayed. When setting difficulty levels, the frequency can be refered to as a standard.

When in the PAGE 2/2 mode, press the TEST BUTTON to penne return to the MENU mode.. XXXXXXXX

SMO0S ~

FIG. 7.12b BOOKKEEPING (2/2)

Page 39

7-13 BACKUP DATA CLEAR

Va

Ne BACKUP DATA CLEAR

YES (CLEAR) >NO (CANCEL)

SELECT WITH SERVICE BUTTON PRESS TEST BUTTON TO EXIT ~\

S/S FIG. 7.13 BACKUP DATA CLEAR, Clears the contents of BOOKKEEPING and high score player ranking entry. When clearing, bring the arrow to “YES” and when not clearing, to “NO”, by using the SER- VICE BUTTON, and push the TEST BUTTON. ‘When the data has been cleared, “COMPLETED” will be displayed. Bring the arrow to “NO” and press the TEST BUTTON to cause the MENU mode to return on to the screen.

Note that the contents of the GAME SETTING, COIN SETTING, and BOARD SETTING are not affected by BACKUP DATA CLEAR operation.
Page 40

8 . MAINTENANCE OF MECHANISM UNIT

@ In order to prevent an electric shock and short circuit, be sure to turn power off before performing work by touching the interior parts of the product.

WARNING! @ Be careful so as not to damage wirings. Damaged wiring can cause an electric shock . or short circuit accident.

8 - 1 ADJUSTMENT AND REPLACEMENT OF SWING VOLUME

Turn the power OFF.

@) Remove the SWING COVER from the front of the

REAR CABINET, Remove the 6 truss screws. Facing the INSIDE REAR COVER, the SWING VOLUME

is on the upper left side.(see photo)

M4X10, chrome

Page 41

Vv. R. 220-5373 5484

To move the Volume Bracket, loosen the 2 screws which secure the Volume Bracket.

Move the Volume Bracket, disengage the gear mesh and turn the Volume shaft so that the d-cut portion of the Volume shaft faces the Volume bracket side as shown.

Have the gears mesh, fasten the 2 scres, and secure the Volume Bracket.

After making adjustments, be sure to perform volume setting in the TEST MODE.

If the volume is malfunctioning, first disconnect the connector which is connected to the Volume, remove the 2 screws which secure the Volume Bracket and remove the Volume Bracket together with the Volume as is attached.

Remove the gear from the Volume shaft and replace the Volume.

Page 42

8-2 GREASING

damage. @ Do not apply greasing to places other than those specified. Greasing to undesignated places can cause malfunctioning and the qualitative deterioration Gror @ Besure to use designated grease. Using undesignated grease can cause parts

IMPORTANT!

of parts.

Once every 3 months, apply greasing to the SWING Volume gear mesh portion, Swing Frame supportive bearings, and Motor gear mesh portion. For spray greasing, use GREASE MATE (PART No. 090-0066).

Apply grease to the Grease Nipple for bearings Apply grease to SWING Volume gear mesh by using the Grease Gun. portion.

Page 43

GREASING TO BRAKE GEAR PORTION

qd) Take out the 4 screws and remove the

Upper Cover.

aa <= x ‘wamou W4X10, chrome

@ By using the spray grease, apply greasing

only to the gear mesh portion.

Page 44

9 .COIN SELECTOR

HANDLING THE COIN JAM

If the coin is not rejected when the REJECT BUTTON is pressed, open the coin chute door and open the selector gate. After removing the jamed coin, put a normal coin in and check to see that the selector correctly functions.

CLEANING THE COIN SELECTOR

The coin selector should be cleaned once every 3 months. When cleaning, follow the procedure below: (@ Turn the power for the machine OFF. Open the coin chute door. Open the gate and dust off by using a soft brush (made of wool, etc.). @ Remove and cleen smears by using a soft cloth dipped in water or diluted chemical detergent and then squeezed dry. (@) Remove the CRADLE. When removing the retaining ring(Ering), be very careful so as not to bend the shaft. ©) Remove stain from the shaft and pillow portions by wiping off with a soft cloth, etc. ©) After wiping as per #5 above, further apply a dry cloth, etc. to cause the coin selector to dry completely.

@ Never apply machine oil, etc. to the coin selector @ After cleaning the Coin Selecting,

IMPORTANT! Insert a regular coin in the normal

working status and ensure that the Selector correctly functions. ©

@ FIG.9b

Insert a coin [

COIN INSERTION TEST mE TEST, simultaneously check the following: down and check O Does the Coin Meter count satisfactorily? rejected O Is the coin rejected when inserted while keeping

Once a month, when performing the COIN SW Button pressed

O Does the Coin Meter count satisfactorily? rejected. O Does the coin drop into the Cashbox correctly? COIN METER

the REJECT BUTTON is pressed down?

4l

Page 45

OPTIONAL DOLLAR BILL ACCEPTOR

@ THE COIN DOOR ASSEMBLY USED ON SEGA WATER SKI COMES EQUIPPED TO ACCEPT A DOLLAR BILL ACCEPTOR. ALL NEEDED WIRING CONNECTIONS ARE CONVIENENTLY LOCATED INSIDE THE GAME FOR THIS APPLICATION.

@ THE COIN DOOR CAN ACCCOMMODATE THE FOLLOWING VALIDATORS:

HOLE POSITION#1 VFMS (MARS)

(FORWARD-MOST POSITION)

HOLE POSITION#2 VFM2 (MARS)

VFM4 (MARS)

DBV45 (JCM)

HOLE POSITION #3 CURRENTLY NOT USED

HOLE POSITION #4 DSIO1*

*The back flange on the chute can be removed for hold position #4. If the flange is not removed, it may interfere with the back of the cabinent.

Page 46

10 .PROJECTOR

Since the Projector has been adjusted at the time of shipment, avoid making further adjustments without good reason.

CAUTION!

The Projector is subject to color deviation due to Convergence deviation caused by the geomagnetism at the time of installation location and peripheral magnetic field. After the installation of machine, and before commencing operation, check for Convergence deviation and if

IMPORTANT! deviated, make adjustments..

Fine adjustments are stored in the Projector. Pressing the Fine Adjustment SW (Convergence Adjustment) results in entering the Fine Adjustment mode, and this may cause the stored fine adjustment to be changed. During work other than for adjustment, Should you topuch the Fine Adjustment SW by mistake, immediately turn power off by using the main SW and then turn it back on again. If any distortion or color deviation is found in the test mode and adjustments are needed, use the specified adjustment knob, or perform adjustment by remote control. To find the adjustment knob, move Cabinet DX and remove the PTV Front Service Door by using the procedure opposite the one for installing and assembling. In some cases a cover is installed to the Adjustment Knobs. Remove the Cover.

10 - 1 CLEANING THE SCREEN

Since the Projector screen is susceptible to damage, pay careful attention to it’s handling. When cleaning, refrain from using water or volatile chemical.

CAUTION!

When the screen surface becomes (

dirty with dust, etc., clean it by using a soft cloth such as gauze. When water, and volatile chemicals such as benzine, thinner, etc., spill on the screen surface, it may be subject to damage, therefore, do not use them. Also, since the surfaces are susceptible to damage, refrain from rubbing them with a hard material or using a duster.

Fig.10.1

Page 47

10-2 MITSUBISHI PROJECTOR

MITSUBISHI PROJECTOR CONTROL PANEL POWER BUTTON

®2e2OeCGO0O0000

Convergence Adjustment SW @) vos 8 H.POS R-GAIN (4) G-GAIN ©® B-GAIN ® ©

  • CONT BRI VW H.W 1 RL. Linearity adjustments in horizontal directions B.HLL. (red or blue) are made. STATIC CONVERGENCE ADJUSTMENT

qa rpva Ob & & o® © e © test Test mode on/off key TEST RB POWER ® ep R/B key Convergence Adjustment SW <J Left shift key

Ob Right shift key

R Vv Lower shift key

a @MA Upper shift key

® POWER Power button

@ For the Convergence adjustment mode, press the test mode on/off key. ©) @ Ensure that “R” is displayed on the screen.

  • Make adjustments so as to cause the red cross pattern to match with the green cross pattern by using Left shift key , Right shift key (5) , Lower shift key sand Upper shift key a . @ By using R/B shift key 13 , cause the red adjustment “R” to shift to blue adjustment “B” and make sure that “B” is displayed on the screen.

In the same manner as in 3 above, cause the blue cross pattern to match with the green cross pattern. © After making adjustment, press the test mode on/off key @® to cancel the convergence adjustment mode.

Page 48

STATIC CONVERGENCE ADJUSTMENT METHOD WITH REMOTE CONTROL

@ Although Remote Control Buttons other than those specified below do not function even if pressed during Convergence Adjust-

Gror ment, do not press them during adjustment work so as to avoid

causing malfunctioning. @ Operate the Remote Control towars the PTV screen. If directed other than to the PTV screen, the Remote Control does not function.

IMPORTANT!

BEFORE USING REMOTE CONTROL: First make sure that the main SW on the Projector’s control panel is ON (the LED adjascent to the main SW is lit). The Remote Control has 2 different types. Depending on the type, the Adjustment procedure is different.

In case of REMOTE CONTROL (Part No. 200-5298): oO) For the Convergence Adjustment mode, press the test button. Ensure that “R” is displayed on the screen.

@ Make adjustment so as to cause the red cross pattern to match with the green cross pattern. < When the red cross matches the green cross, the green cross turns yellow or white. -~

Use remote control buttons shown below to move the red cross as follows: | Button @———_ to the left 2222 ad to the right (Sooo —___— Upward ——— Downward

Use Remote Control button 6 to shift “R” to “B”. Make sure that “B” is displayed on the screen. Each 1 . 5 fe} ofea a

time Button(6) is pressed, red and blue adjustments ® In the same manner as in@2)above, cause the blue OOO oO

are shifted. on) e)

< cross to match the green cross. When the blue cross 2 . 3 . 4 <6) ODO matches the green cross, the green cross turns white. OD O

© After adjustment is made, press the test button to 0600

cancel the Convergence Adjustment mode. *When 2 minutes or more elapses in the Convergence mode screen without taking any action, the on-screen adjustment mode will disappear.

Page 49

In case of REMOTE CONTROL (Part No. 200-5532):

® Press the TEST KEY to have the red line

adjustment screen appear.

Oo) Superimpose the red cross on the green cross at

the center of the screen. Move the red cross to the left, right, up, and down respectively with the corresponding buttons of the remote control. When the red cross is superimposed on the green cross, the green cross turns into yellow or white. Redlineadjustment

Press the R/B Key to have the blue line adjustment screen appear. Each time R/B Key is pressed, the red line and blue line will be alternated. Press shift to superimpose the red line on the green line. .

7 O) In the manner similar to 2) above, press each

key to superimpose the blue cross on the green cross. When it is superimposed, the cross in the center will become white. RED xXx

©) Press the TEST KEY to exit from the adjustment mode.

Completion of Adjustment. (6) During STATIC CONVERGENCE Adjustment

Mode, if no action is taken within 5 minutes, the adjustment mode will be exited automatically.

NORMAL FUNCTIONING

H- WIDTH Adjustment mode ‘The horizontal width of image is adjusted.

Every time the PICTURE KEY is pressed, the Adjustment mode proceeds sequentially in order as above.

In each Adjustment mode, press the + or - key to make adjust ment. In each Adjustment mode, unless the key input (value or image variation) is effectively performwed within approxiamately 6 seconds, the Adjustment mode is automatically cancelled and shifts to the normal image. When the horizontal width or vertical width is adjusted the convergence is automatically corrected (auto adjuster functioning).

Page 50

11 .REPLACEMENT OF FLUORESCENT LAMP AND LAMPS

@ When performing the work, be sure to turn power off. Working with power on can cause an electric shock or short circuit accident. @ The Flourescent Lamp, when it gets hot, can cause burns. Be very careful when replacing the Fluorescent Lamp.

CAUTION! To perform work safely and securely, be sure to prepare a step which is in a secure and stable condition. Not using a step or using an unstable step can cause a violent falling down accidents.

11 -1 REPLACEMENT OF FLUORESCENT LAMP

  • Take off the 3 screws which secure the Holder on the upper part of Billboard.

@ Take out the billboard from the cabinet and replace the fluorescent lamp (20W)

TRUSS SCRE¥_ (3) M48, black

BILLBOARD

PREPARE A STEP BEFORE PERFORMING WORK.

Page 51
  • PERIODIC INSPECTION TABLE

The items listed below require periodic check and maintenance to retain the performance of this machine and ensure safe operation.

@ Be sure to check once a year to see if Power Cords are damaged, the plug is securley inserted, dust is accumulated between the , Socket Outlet and the Power Plug, etc. Using the product with

WARNING! dust as is accumulated can cause a fire or electrical shock. Periodically once a year, request the place of contact herin stated or the Distributer, etc. where the product was purchased from, as regards the interior cleaning. Using the product with dust as is

accumulated in the interior without cleaning can cause a fire or

accident. Note that cleaning the interior parts can be performed on a pay-basis.

ITEMS DESCRIPTION PERIOD REERENCE

CABINETEnsure that adj. are in contact | Daily1

with floor

Check hazard preventive Daily 1

parts

FOOT CONTROLLER Check volume and sensor Monthly 7

Apply greasing to volumeTrimonthly7

gear, R guide and brake gear

COIN SELECTOR Check COIN SW Monthly 7 PROJECTOR Screen cleaning Weekly 10

COIN SELECTOR cleaning __| Trimonthly 9

Check adjustmentsMonthly4,7, 10
GAME BDSetting check,Monthly7
INTERIORCleaningAnnuallysee above.

POWER PLUG Inspection and cleaning

CABINET SURFACECleaningAs necessary | see below

CLEANING CABINET SURFACES

When the cabinet surfaces are badly soiled, remove stains with a soft cloth dipped in water or diluted (with water) chemical detergent and squeezed dry. To avoid damaging surface finish, do not use such solvents as thinner, benzine, etc. other than ethyl alcohol, or abrasives, bleaching agent and chemical dustcloth.

Page 52

13 . TROUBLESHOOTING Should trouble occur, first check connector connections.

PROBLEMS CAUSE COUNTERMEASURES

With Main SW ON, no activation Power is not supplied.

Power supply/voltage is not correct.

AC main fuse causes the power to be cut off due to momentary overload. Plug in correctly

Make sure that power supply/voltage is

Check fuse. Remove the cause of overload and replace fuse

Foot Controller operation is unsatisfactory Poor mesh of ADJUST GEAR

VR. deviation of malfunctioning.

Poor VR. setting Adjust gear mesh

Adjust or Replace V.R.

Perform VR. setting.

Irregular sound emitted from inside Rear Cabinet Greasing to gear mesh portion is not satisfactory, or extraneous matter mixed in. Apply greasing or eliminate extraneous matter.

The color of the image on PROJ. screen is incorrect. Connector connections are defective. Check the connection for the RGB and SYNC connectors of the PROJ. TERM. BD and VPM BUFFER BD.

The image on PROJ. screen has color deviation. Affected by the magnetic field of installation location. Make CONVERGENCE adjustment. (Refer to Section 9.)

No sound is emitted. Sound Volume adjustment is not appropriate.

Sound BD and speaker are malfunctioning. Adjust sound volume. (see Section 6).

Perform sound test to find and replace defective parts.(Refer to Section 6).

During advertise the Foot Controller cannot be locked Connection fault of connector between Front Cabi and Rear Cabi

Due to instantaneous over current, fuse on ASSY ELEC is blown Accurately connect the Connector.

After eliminating the cuase of overcurrent, replace the fuse.

The Fluorescent lamp does not light up. The Fluorescent tube is burnt out. Replace the Fluorescent tube (Refer to Section 10).

Switches of Control Panel, Switch Unit, Foot Sensor (PITCH), etc. cannot be turned ON or OFF. Connection fualt of connector between Front and Rear Cabi. Accurately connect the connector.

Page 53

13 - 1 REPLACEMENT OF FUSE

@ !n order to prevent an electric shock, be sure to turn power off before performing work by touching the interior parts of the product. @ Be careful so as not to damage wirings. Damaged wiring can cause an electric shock or shor circiut accident

WARNING!

@ After eliminating the cause of the blowing of fuse, replace the fuse. Depending on the cause of the fuse blowing, using the fuse as is blown can cause generation of heat resulting in fire.

Turn off the AC Unit’s Main SW.

Unplug from the Plug Socket. QO CO

Remove the 2 truss screws, unlock with the

Master Key, and remove the Back Door from the rear part of the Front Cabi.

‘O) Two types of fuse are on the Power Supply Unit.

TRUSS SCREW (2) M4X25, Black

Page 54
  • GAME BOARD
WARNING!
CAUTION! @ In order to prevent an electrical shock, be sure to turn power off before performing work by touching the interior parts of the product. @ Be careful so as not to damage wirings. Damaged wiring can cause an electric shock or short circuit accident.

Do not expose the Game BD, etc. without a good reason. In this product, setting changes are made during the test mode. The Game BD need not be operated. Use the Game BD, etc. as is with the same setting made at the time of shipment.

14-1 REMOVING THE IC BOARD

The IC board such as Game BD, etc., is on the Rear side of the Front Cabi.

Take out the 2 Truss screws, unlock with the Master Key, and remove the Back TRUSS SCREW (2) Door from the rear part of the Front M4X25, Black Cabinet.

Take out the3 screws, unlock with the Master Key, and remove the Back Door from the rear part of the Front Cabinet. (photo 14.1a)

SHIELD CASE LID Unlock with the Master Key

Page 55

14-2 COMPOSITION OF GAME BOARD

GAME BD SPW ROM BD SPW (833-13204) (834-13205)

MODEL 2 C-CRX MAIN BD COM (837-12469-01) MODEL 2 C-CRX MAIN BD COM (837-12469-91)

SCREW (9) X39, flat spring washers used SCREW (4 Ww | spring washers

Page 56
  • DESIGN RELATED PARTS

(Grae 90.) G4) Caras (8) )

) (crs ste) (24)

Page 57

ITEM NO.

wns OIA

ll PART NO.

423-0303-91 SPW-1301 SPW-3003-B SPW-3003-C SPW-3003-D SPW-3003-E SPW-3003-F SPW-3003-G SPW-3003-H SPW-3010-B SPW-3011-B SPW-3004-B SPW-3004-C SPW-3004-D SPW-3004-E SPW-3851-B SPW-3851-C 422-0628-01 421-7308-~ SPW-3851-E SPW-0001-01 SPW-3702 SPW-9617-91 SPW-9618-91 DESCRIPTION

BILLBOARD PLATE SPW STICKER FRONT PANEL STICKER SWING COVER A. STICKER SWING COVER B STICKER SWING COVER C STICKER SWING COVER D STICKER SWING COVER E STICKER SWING COVER F STICKER SWING COVER G STICKER SIDE LID L STICKER SIDE LID R STICKER UPPER COVER A STICKER UPPER COVER B STICKER UPPER COVER C STICKER UPPER COVER D STICKER CONT PNLA STICKER CONT PNL B PLAY INSTR SH SPW ENG DENOMI SHEET I GAME STICKER CONT PNL ENG

CAUTION MAT SPW ENG STICKER TOWER STICKER PTV SIDE L SPW. STICKER PTV SIDE R SPW
Page 58
  • PARTS LIST

TOP ASSY SEGA WATERSKI

Page 59

TOP ASSY SEGA WATERSKI

ITEM NO. PART NO. DESCRIPTION

1SPW-1000ASSY FRONT CABI
2SPW-3000ASSY REAR CABI
3ASK-0001CONT PNL PLATE

4 SPW-0001-01 CUATION MAT SPW ENG 5 DYN-O011 DENOMI PLATE W/O ORIGINAL 6 421-7308-~ DENOMINATION SHEET 1 GAME. 7 422-0628-01 PLAY INSTR SH SPW ENG 101 600-6695-01 AC CABLE CONNECT TYPE USA 154

Page 60

ASSY FRONT CABI (SPW-1000)

ITEM NO. PART NO. DESCRIPTON

1 SPW-1100 ASSY BASE CABI 2 SPW-1200 ASSY PTV 3 SPW-1300 ASSY FRONT PANEL 4 SPW-1001 PTV HOLDER

Page 61

ASSY BASE CABI (SPW-1100)

ITEM NO.

we PART NO.

SPW-1120 SPW-1140 SPW-1150 SPW-4000 SPW-4100 DESCRIPTION

AC UNIT ASSY BACK DOOR ASSY SUB BASE CABI ASSY ELEC ASSY MAIN BD

Page 62

AC UNIT (SPW1-1120)

MAIN SW

POWER CORD. ,

MAIN SW is OFF,

ITEM NO. PART NO. DESCRIPTION

1 SPW-1121 AC BRKT 104 509-5453-91-V-B SW ROCKER TYPE J8 V-B

Page 63

ASSY BACK DOOR (SPW-1140)

ITEM NO. PART NO. DESCRIPTION

1 ASK-1141 BACK DOOR 2 TH-1015 LOCKING TONGUE 101 220-5575 CAM LOCK MASTER W/O KEY

Page 64

ASSY SUB BASE CABI (SPW-1150)

Page 65

ASSY SUB BASE CABI (SPW-1150)

ITEM NO. PART NO. DESCRIPTION

1SPW-1151BASE CABI
2ASK-1152LOCK BRKT
3105-5238FAN BRKT
4UP-1018AIR VENT
ByARC-1006LEG BRKT
6117-5191PLATE

101 260-0011-02 AXIAL FLOW FAN AC100V 50-60Hz

102601-8543FAN GAURD
103999-0168CASTER 2 1/2"

104 999-0167 LEVELER (LEG ADJUSTER BOLT)

Page 66

ASSY ELEC (SPW-4000)

ITEM NO. PART NO.

SPW-4001 GBN-4002 839-0451-01 838-11650-32 838-11856-01 560—5345 LOCAL PURCHASE LOCAL PURCHASE 514-5084 DESCRIPTION

WOODEN BASE ELEC HANDLE LIGHT CONTROL BD TTR EQ. PWR AMP SPW CONNECT BD W/FUSE & COVER PWR XFMR 114.8 VA FUSE FUSE FUSE HOLDER

Page 67

ASSY MAIN BD (SPW-4100)

ITEM NO. PART NO.

1 SPW-4101 2 GBN-4102 3 SPW-0100 4 839-0582-03 101 400-5306CE-01 DESCRIPTION

WOODEN BASE MAIN SW REG BRKT ASSY SHIELD CASE RGB BUFFER BD 0.7V OUT BNC SW REG +5V +12V -5V CE

Page 68

ASSY SHIELD CASE (SPW-0100)

ITEM NO. PART NO. DESCRIPTION

1105-5218SHIELD CASE
2105-5219-91SHIELD CASE LID
3833-13204GAME BD SPW
4839-0949-01FLT BD C-CRX SPW
102260-0055FAN MOTOR DC 5V
Page 69

ASSY PTV (SPW-1200)

SEE A

Note: 1. SCREW FASTENING TORQUE TO BE W4:18kgf-cm 5: 25kgf-cm

we

ITEM NO. PART NO. DESCRIPTION

1SPW1-1220ASSY BILLBOARD
2MGL-1150ASSY MASK
3RAL-0501MASK HOLDER

101 200-5639-SPW ASSY PROJECTION DISPLAY US SPW

Page 70

ASSY MASK (MGL-1150)

ITEM NO. PART NO.

MGL-1102 MGL-1151 MGL-1152 DESCRIPTION

TV MASK SLIT PLATE MASK SIDE HOLDER

Page 71

ASSY BILBOARD (SPW1-1220)

ITEM NO. PART NO. DESCRIPTION

1SPW-1221LEFT COVER
2SPW-1222RIGHT COVER
3SPW-1223BILLBOARD BOX

4 SPW-1224 BILLBOARD HOLDER 5 423-0303-91 BILLBOARD PLATE SPW

10280-5308SPACER 4.5-12X2

101 LOCAL PURCHASE ASSY FL 20W EX W/CONN HIGH T CE

Page 72

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 73

ASSY REAR CABI (SPW-3000)

ITEM NO.

SIDHAWNE .o

ll PART NO.

SPW-3100 SPW-3200 SPW-3500 SPW-3700 SPW-3800 SPW-3850 ASK-3001 ASK-3002 SPW-3001 SPW-3002 SPW-3003 SPW-3004. SPW-3005 SPW-3006 SPW-3007 SPW-3008 SPW-3009 SPW-3010 SPW-3011 SPW-3804. SPW-3010-B SPW-3011-B 440-CS0094-EG 100-5249 DESCRIPTION

ASSY SUB REAR CABI ASSY SWING CONTROLLER, ASSY BRAKE MECHA ASSY COIN CHUTE TOWER ASSY CONT PNL BASE ASSY CONT PNL SWING LINK BAR BOTTOM BOARD PIPE HOLDER L PIPE HOLDER R SWING COVER UPPER COVER FRAME LID F GRIP PIPE GRIP SUPPORT L GRIP SUPPORT R HOLDER PLATE SIDE LID L SIDE LIDR PIPE HOLDER STICKER SIDE LID L STICKER SIDE LIDR STICKER C FOR PLAYER ASK ENG BEARING FAI16

Page 74

ASSY SUB REAR CABI (SPW-3100)

Note: SCREW FASTENING TORQUE TO BE 218kgf-cm M10:354kgf-cm

ITEM NO. PART NO. DESCRIPTION

1 SPW-3101 REAR FRAME 2 ASK-3102 BUFFER BRKT 101 601-8918 SHOCK ABSORBER RH

Page 75

ASSY SWING CONTROLLER (SPW-3200)

N4:18kef-co M14 :800kgf-cm

Note: SCREW FASTENING TORQUE TO BE

SECTION A-A

Page 76

ASSY SWING CONTROLLER (SPW-3200)

ITEM NO.

URwWNe PART NO.

ASK-3250 SPW-3300 SPW-3400 ASK-3201 ASK-3202 ASK-3203 111-0050 280-5009-01 000-P00408-W FAS-200005 060-S01400 060-F01400 050-H00800 030-000820-S 060-F00800 050-U00800 000-F00308 DESCRIPTION

ASSY SWING VOLUME ASSY SWING FRAME L ASSY SWING FRAME R SWING FRAME BASE SWING ROSTA BRKT STEP LINK ROD LINK BALL RBL8D CORD CLAMP 21 M SCR PH W/FS M4X8 HEX SKT H CAP SCR B OZ M14X40 SPR WSHR M14 FLT WSHR M14 HEX NUT M8 HEX BLT W/S M8X20 FLT WSHR M8 UNUT M8 M SCR FH M3X8

Page 77

ASSY SWING VOLUME (ASK-3250)

ITEM NO. PART NO. DESCRIPTION

1 ASK-3251 SWING VOL BRKT 2 601-7945 GEAR 20 101 220-5373 VOL CONT B-5K

Page 78

ASSY SWING FRAME L (SPW-3300) ASSY SWING FRAME R (SPW-3400)

Details of PART A

Note:

Page 79

ASSY SWING FRAME L (SPW-3300)

ASSY SWING FRAME R (SPW-3400)

ITEM NO.

ll PART NO.

SPW-3350 SPW-3450 SPW-3301 SPW-3401 ASK-3302 ASK-3402 ASK-3303 ASK-3307 ASK-3308 ASK-3309 SPW-3302 SPW-3402 SPW-3303 SPW-3403 ASK-3312 ASK-3406 ASK-3313 ASK-3407 TTR-2009 TTR-3205 601-6005 100-5240 601-8917 050-H01400 060-S01400 000-P00408-W FAS-000029 020-000830-HZ 060-S00800 060-F00800 028-C00416-P 050-U00500 030-000820-S 000-F00308 DESCRIPTION

ASSY STEP L ASSY STEP R SWING FRAME L SWING FRAME R STEP COLLAR L STEP COLLAR R LINK BRKT ROSTA SPACER STEP ROSTA BRKT SWING GEAR 130 WIRE COVER L WIRE COVER R TUBE HOLDER L TUBE HOLDER R UPPER PROTECTOR L UPPER PROTECTOR R LOWER PROTECTOR L LOWER PROTECTOR R GEAR HOLDER 80 FLT 14.5-36X3.2 ADJUST GEAR BEARING FAI30 ROSTA 22 HEX NUT M14 SPR WSHR M14 M SCR PH W/FS M4X8 M SCR PH W/FSM4X50 HEX SKT CAP SCR BLK OZ M8X20 SPR WSHR M8 FLT WSHR M8 SET SCR CH CUP P M4X16 U NUT M5 HEX BLT W/S M8X20 M SCR FH M3X8

Page 80

ASSY STEP L (SPW-3350)

ASSY STEP R (SPW-3450)

Page 81

ASSY STEP L (SPW-3350)

ASSY STEP R (SPW-3450)

ITEM NO.

N

wIdaAHwaRwW

ll PART NO.

SPW-3351 SPW-3451 SPW-3352 SPW-3452 SPW-3353 SPW-3354, ASK-3355 ASK-3356 ASK-3357 SPW-3374, SPW-3380 ASK-3362 ASK-3363X SPW-3356 SPW-3357 SPW-3358 SPW-3359 SPW-3360 SPW-3361 SPW-3363 SPW-3364. SPW-3365 SPW-3366 SPW-3367 SPW-3453 SPW-3368 SPW-3390 SPW-3369 SPW-3370 SPW-3371 SPW-3372 3376 601-8847 000-P00412-WB 000-P00408-W 050-U00800 050-U00600 030-000820-S 060-F00600 030-000820-S 060-FO0800 DESCRIPTION

STEP BASEL STEP BASER STEP COVER L STEP COVER R COVER HOLDER L COVER HOLDER R COVER HOLDER B EDGE GUARD A EDGE GUARDB EDGE GUARD C SENSOR UNIT CUSHION A CUSHION B STEP SHAFT PITCHING SHAFT COLLAR 17 STOPPER BOLT STOPPER RUBBER SENSOR PLATE ROSTA BRKT 18X30 SIDE GUARD PLATE FRONT GUARD PLATE REAR GUARD PLATE GUARD HOLDER F L GUARD HOLDER FR GUARD HOLDER R ASSY STOPPER KEY 5X5-12.5 RUBBER HOLDER A RUBBER HOLDER B RUBBER HOLDER C COVER HOLDER F ROSTA DR-S-18X30 M SCR PH W/FS BLK M4X12 M SCR PH W/FS M4X8 U NUT M8 U NUT M6 HEX BLT W/S M6X12 FLT WSHR M6, HEX BLT W/S M8X20 FLT WSHR M8

Page 82

SENSOR UNIT (SPW-3380)

ITEM NO. PART NO. DESCRIPTION

1 SPW-3382 SENSOR BASE 101 370-5138-01 SENSOR ASL

Page 83

ASSY STOPPER (SPW-3390)

ITEM NO. PART NO.

SPW-3391 SPW-3392 030-000616-S 068-652016 DESCRIPTION

STOPPER BRKT STOPPER RUBBER S HEX BLT W/S M6X16 FLT WSHR 6.5-20X1.6

Page 84

ASSY BRAKE MECHA (SPW-3500)

——)

Hote: SCREY FASTENING TORQUE TO BE

W8:178kgf-cm

ITEM NO. PART NO. DESCRIPTION

1ASL-3350BRAKE UNIT
2SPW-3501BRAKE BRKT

201 030-000820-S. HEX BLT W/S M8X20

202060-FO0800FLT WSHR M8
Page 85

BRAKE UNIT (ASL-3350)

NSS A

i XX SSIS SS

ITEM NO. PART NO. DESCRIPTION

1ASL-3351BRAKE BASE
2ASK-3603PINION GEAR 25
3ASL-3353BRAKE SHAFT
4ASK-3606KEY 5X5-10.5
101601-8982BRAKE BXH
102100-5229BEARING 17
201060-S00500SPR WSHR M5

202 065-S014S0-Z STP RING BLK OZ S14 203 065-A030HO-Z STP RING BLK OZ H 30 204 020-000530-0Z HEX SKT H CAP SCR BLK 0Z M5X30.

Page 86

ina

SECTION C-C

ASSY COIN CHUTE TOWER (SPW-3700)

Page 87

ASSY COIN CHUTE TOWER (SPW-3700)

ITEM NO.

Auwne PART NO.

MIT-3350 SPW-3701 INY-1162 DP-1167 105-5172 BOX-CASH 220-5237-92-~ 220-5574 220-5575 DESCRIPTION

SW UNIT COIN CHUTE TOWER METER BRKT TNG LKG CHUTE PLATE DOUBLE CASH BOX ASSY C.C.2 DOOR CAM LOCK W/KEY CAM LOCK W/O KEY

Page 88

SW UNIT (MIT-3550)

ITEM NO. PART NO.

INY-1181 421-8126 220-5179 509-5028 601-0042 DESCRIPTION

SW BRKT STICKER SW PANEL VOL CONT B-5K OHM SW PB 1M KNOB 22 M

Page 89

ASSY CONT PNL BASE (SPW-3800)

ITEM NO. PART NO.

1 SPW-3801 2 ASK-3802 3 ASK-3803 101 130-5162 DESCRIPTION

CONTRL PNL BASE SPEAKER BRKT BOTTOM SUPPORT GULL BOX SPEAKER 80 OHM 8W

Page 90

ASSY CONT PNL (SPW-3850)

ITEM NO. PART NO. DESCRIPTION

1 SPW-3851-01 CONTRL PNL COVER ENG 2 SPW-3852 SPEAKER NET L 3 SPW-3853 SPEAKER NETR 101 509-5547-91-02 SW PB 60M RED W/L 102 509-5547-91-03 SW PB 60M BLUE W/L

Page 91

Come see Sega GameWorks Service Department’s Homepage

Netscape: SEU SERVICE HOMEPAGE

°° @t¢ereunaid gs A [http 7 Avww seuser vice com/SEGASERVICE /mainpage htm!

Gl” what’s Related

MAILING LIST

SEGA DISTRIBUTORS

SERVICE STAFF

DARL'S OFFICE

HOME

[Y¥2K COMPLIANCE]

Sega Enterprises Inc.,USA Service Department Phone (650)-632-7580 Fax (650)-632-7594

Best Viewed with [What's new] [Manuals] [Bulletins] [Part Numbers] [Game Monitors] [Board Systems] [Mailing List] [SEGA Distributors] [Service Staff] [Darl's Office] [Samples]

Coin-Op Links:

Star Tech Journal

Amusement industry Mega Site

if you have any questions about this Home Page please E-Mail to:

dari.davidson@seu.sega.com OR han.rockhifi@seu.sega.com

A total of 3910 people have accessed this page.

Page 92

SEGA

SEGA ENTERPRISES, INC. (USA)

45133 Industrial Drive Fremont, CA 94538 415/650-802-1750 phone 415/650-802-1754 fax