CATHODE RAY TOMES

Pursuit TM-019

Pursuit (Atari) · Technical Manual · 46 pages · 22 sections · original scan

Page 1

TM-019

PURSUIT

Service Information

(PCB Logic)

A ATART Innovative leisure

14600 WINCHESTER BOULEVARD, LOS GATOS, CALIFORNIA 95030 - TELEPHONE (408) 374-2440 - TELEX 357-488

Page 2

>

Oo nm 0D 9 Ww PURSUIT

TABLE OF CONTENTS

INTRODUCTION/WARRANTY

NEW MACHINE SET-UP PROCEDURE

SERVICE ACCESS

NEW MACHINE CHECKOUT

PLAY

CIRCUITS

SET-UP PROCEDURE

PRODUCTION BOARD TESTS

MOTOROLA MONITOR

Q-530 COIN ACCEPTOR ADJUSTMENT & MAINTENANCE

GENERAL MACHTNe MAINTENANCE

TROUBLESHOOTING

P.C.B. SHIPPING

Page 3

INTRODUCTION/WARRANTY

PURSUIT is a video amusement device which simulates flying a fighter

plane.

This game has been designed with solid state circuitry to be as

maintenance free as possible. However, as with all devices mechanical

or electrical, there may be minor problems, If the printed circuit board (PCB) fails within the 90 day*warranty period, contact the

distributor from whom the game was originally purchased for replacement

or repair instructions. All such warranty returns must be accompanied

by completed warranty return forms, Any PCB repairs attempted by

anyone other than authorized Atari Service Center personnel will void

the warranty. If the PCB fails after the warranty period has expired,

it will be repaired for a nominal parts and labor charge.

Atari, Inc. warrants the T.V. monitor for a period of 30 days

commencing the day of shipment from the Atari factory, If the monitor

fails within that period, immediately contact the distributor from

whom the game was originally purchased for repair or replacement

instructions. Any T.V. repairs (other than replacement of fuses or

adjustments) attempted during the warranty period by anyone other

than authorized Atari Service Center personnel will void the warranty.

If the T.V. monitor fails after the warranty period has expried, it

may be returned to the distributor where it will be repaired for a

nominal parts and labor charge, or it may be taken to any competent

T.V. repair shop

*(From date of shipment from the factory)

Page 4

NEW MACHINE SET-UP PROCEDURE

Before turning this machine on, inspect it carefully for any damage

which may have occurred during shipment. Inspect both interior and

exterior of the machine for any obvious damage to the cabinet or

internal components. Check for cracked or broken cabinet parts,

assemblies pulling loose, broken or disconnected wires or foreign

objects shorting electrical connections, After the machine has been

plugged in and turned on, perform the checkout procedure,

-__ SERVICE ACCESS

All servicing is performed at the rear of the machine through the rear

door which provides access to all components, sub-assemblies, and

adjustments with the exception of the coin box, The coin door is

located on the front of the machine underneath the control panel. To

remove the coins, unlock the metal coin door and open. This exposes

the coin box.

To reach the interior of the machine, unlock and remove the rear door.

Please note that an interlock switch is provided for this door so that

the machine is completely turned off whenever this door is opened.

These switches protect the operator from accidental shock and so they

must always be kept in perfect working order, If the machine is

adjusted or tested with the rear door open, the interlock switch must

be placed in the closed (or "on" position) by pulling out the white

actuator shafts,

WARNING; The covered black terminal block carries full line voltage

whenever the line plug is connected to a power outlet, This cover

should be removed only with the line plug disconnected. Do not leave

off the cover once it has been removed,

Page 5

WEW MACHINE CHECKOUT

As each new machine leaves the factory, every component and subassembly

is carefully checked for proper operation. However, since parts may

have been damaged or adjustments changed during shipping, the following

checkout procedure must be repeated prior to placing the machine on

location:

1. Inspect both the exterior and interior of the machine for obvious

shipping damage such as cracked or broken cabinet parts, sub-

assemblies broken loose, etc.

Carefully inspect the interior of the machine to see that all

solder joints, slip-on connectors and plug-in type connectors are

firmly seated. Pay particular attention to the PCB edge connector,

the fuses and the connectors to the potentiometers. Also check

the connections to the coin switch, the T.V, monitor, the interlock

switches and all the other Molex-type connectors,

Plug the machine in, and pull out the white actuator shafts of

the interlock switches if the rear door is open, Inspect the CRT

(cathode ray tube) image for a steady and sharp picture which

exhibits the proper levels of brightness and contrast.

Insert several old and new coins into the coin acceptor. No genuine

coin should be rejected and each coin insertion should step the coin

counter one digit. Depress the coin rejector button to make sure

that the linkage is operating smoothly.

Coin insertion should start the game, (Check for proper game

sequence, making sure that all aspects of the game - i.e. plane

display and control, score count and display, etc. are functioning

correctly. If you are not familiar with the game sequence for

Pursuit, read the game sequence description.

Page 6

The door locks should turn to the "locked" and "unlocked"

positions smoothly and the doors should open and close without

binding.

The interlock switches must turn off the entire machine when the

rear door is opened. (See the "WARNING" under Section C).

Page 7

E, PLAY

Picture:

Joystick moves forward and backward and

from side to side.

Page 8

In the preceding figure, the view is from the cockpit of a Pursuit

airplane. The cross hairs are the sights of an airplane-mounted

machine gun.

Control is with a joystick. Pushing the joystick forward causes the

airplane to dive. Backward, it causes the airplane to climb. Turning

right is accomplished by moving the joystick to the right, and turning

left is accomplished by moving the joystick to the left. This is

exactly how a real World War I Pursuit aircraft was controlled.

Attract Mode: (1) Enemy aircraft (being followed) remains on the screen.

It will normally wander randomly up and down and from side to side. Occasionally it will stick on edge awaiting random circuit instructions

to push it back towards the center of the screen.

  • Sound is shut off in attract mode permitting machine

gun to be fired continuously. This is evident by a flashing spot of

light in the center of the cross hairs.

  • If the wandering enemy aircraft moves through the

center of the cross hairs, it will be shot down. A shoot down is

followed by an explosion sequence. The enemy disappears while the

debris of the destroyed aircraft radiates outward from the center. In

the latter half of the explosion sequence, a new airplane reappears on

the screen. Another plane is chalked up on the scoring strip on the

right hand side of the screen.

Page 9

Play Mode: The enemy aircraft moves randomly as in the attract mode, but

now we control our airplane to shoot him down. If the enemy is below us

we dive to get him. Pushing the stick forward does this. The horizon is

seen to move up whilewe get nearer to getting the enemy into the gun

sights. Conversely, if the enemy is high we climb to get him. The horizon

moves down as we get closer. Engine sounds are present in the play mode

and they change depending on whether we are climbing or diving.

If the enemy is to the right or left we move the stick sideways to catch

him. A motion to the right causes the cross hairs to tilt right simulating

the bank of the other airplane. The machine gun is fired by pressing the

button on top of the joystick. In addition to flashes of light in the

center of the cross hairs, a machine-gun sound comes from the speaker.

A hit results in the explosion of the enemy with the attendant picture

of flying debris (see Attract Mode), but we also have the explosion noise.

The noise is slightly delayed from the hit. There are 2 series of

explosions. The enemy disappears from the screen during the first

explosion but he reappears during the second explosion.

Scoring and game time are recorded on the left and right sides of the screen.

Play time shows up as a bar on the left. This is intended to simulate

a gas gauge. It starts as a bar that extends to the top. As the game

procedes it shortens until at the end of the game it disappears. Extended

play results in a gas tank refill occuring at the skill level that has been

set into the PCB with coded switches.

Page 10

Scoring is done with small marker planes on the right side. A hit marks

one plane (light) on the upper right. A score of 15 (light) airplanes is

possible, then the score restarts at the top with dark markers. 30 is the

maximum recorded score. In addition to score marks, the illuminated

tags are as follows:

4 WASHOUT

8 STUDENT PILOT

12 EAGLE

16 ACE

Switches on the PCB enable setting to any of these levels for Extended Play.

For example, if Extended Play is set for EAGLE, then when EAGLE is attained

the game time starts over again. This is seen as a refill of gas. At the

end of the game sound and control cease.

Page 11

F. CIRCUITS

  • Coin and game time. Schematic region CC6, DD6, 7.

a. Devices Q5 AB, 1 A8QA7 4B6 | 206, 47,5 ABEEG, D7, Ab,

b. Game starts when a voltage is applied at terminal 18. This

is also the terminal to which the coin counter is connected.

Current to the coin counter flows through the coin switch.

According to cherry switch this current helps keep this switch

operational. Diode CR13 holds down voltage spikes. Voltage

must be at terminal 18 long enough for C36 to integrate up

to Q5 conduction (.7V). Q5 sets Flip Flop ABI 1g when it conducts. A8 is a Hysterisis device to give extra protection

against noise or sparks triggering the game ON. (23 also helps prevent this. GT means GAME TIME and is used in the

same sense as ATTRACT is used in other games. When GT is

TRUE 555 timer (E6) is released to operate (Terminal 4).

E6 operates in the A stable mode. 8 cycles of operation

comprise a Game. These cycles of operation are counted in

7493-D7. The termination count is when the 4's significant

FF comes ON. This goes through B6, A6 and A7 to reset the

Game FF (A8)1_g)- When power is first applied to the game or an interruption in power occurs, the Q6 circuit assures that

game time will be in the OFF state. The rising 5V charging

C37 causes Q6 to conduct and reset via A6 and A7.

  • Game time display. Schematic region DD6-EE6

a. Devices C714 8,68712,6,4,2°°74° C6q, D4, Aly

Page 12

The game time count is compared to functions V32,64; and 127 in C7. When scan has moved down the screen to the point that

comparison is TRUE, this result is latched in C6,. The “moving down" vertical signal is ANDed with A functions in D4g to generate the fuel video bar.

  • Score, Memory and Display. Schematic region CC5,6 - DDS ~ EES.

a. Devices L63F7¢, L8,, 34,0975 966 11,83°°**86 10,8,4°--K34> K34> N43, ka kag, L4,, Lai. K43K3) 3-10, D4, M4, Ay, F65_19-47 C6g> 99, Q10, QIT, Q8, Ql2

Score memory is 5 bit counter L6, J7. At GT score is reset

to "zero" via L613 and Bog. Score is accumulated by counting explosion pulse arrowing from L6,. Score is compared with Functions V16, V32, V64 and V128 in comparison to J6 to generate a pulse when vertical scan moves down to the amount of score count. The occurance of this compare is stored in FF, 34>

K3q. The correct number of score marks (airplanes) is gated in at D4,. Airplane shape is formed at inputs 1,2, and 4 to D4

in at D4,. Airplane shape is formed at inputs 1,2, and 4 to D4. FF-N4,3 and Kay, form the "line" for score wings. The major position of the score body is formed in L4,_,, and K4,. Further shaping and vertical segmentation is done by K313 and K31 9° Exclusive gate M4g is used to reverse the polarity of the score signal from white to black for score counts 15 to 30. At

count of 15 is by J4i9 and the connection to L6,4 causes the least significant bit to be forced to ONE on the next count. This is done for skip count 15-17 as polarity of score changes. Otherwise there would have been no score showing at the 16th

Page 13

score. Score is decoded at H7 for operating skill lights (H7 is BCD to decimal order), DIP switch P6 selects level

at which extended play starts (4 to 8, 12, or 16). When the

extended play level is reached FF C6g is set lighting

EXT PLAY lamp and resetting fuel to full via A7 AB, . AB. is

a hysterisis gate and is operated in this circuit as a

monostable detecting rising voltage (FF-C6g coming ON).

  • Sound circuits. Schematic region DDS, EE5-6-7-8/

a.

b. Devices QX, N3, Q1, N2, K8, N8, N5, LM380, M8_L8,017.

Machine gun sound is generated by discharging capacitor c43

through the speaker voice coil. The machine gun pulses operate

relay L10 to do this. R118, CR8, CR11 are noise suppression

components to limit kickback from speaker inductance due to

machine gun operation. C43 recovers its charge between shots

through R115. Machine gun sound is enabled only during GT

(m8, ). The fact that audio from LM380 is disabled during

machine gun sounds is scarsely discernable, but this causes

considerable distortion of explosion sounds. Therefore,

explosion disables the machine gun (M85). The explosion sound

is constructed from a noise source (Al and N2) and a solid

variable gain amplifier QX and CA3080, Noise is generated by

Ql which is a 2N3643 whose base to emitter junction is forced

into an avalance (Zener) mode by applying 15 volts through 680K. In this mode white noise is generated. The noise is amplified

by N2 to the extent that some clipping occurs.

-ll-

Page 14

Noise is input to CA3080 at Pin 3 after the attenuation of

6.8K/150K. The CA3080 amplifies fully when QX pulls up pin 5.

The rate of pull-up is controlled by R13. The rate of

decay is controlled by R12. Motor sounds are generated

digitally in A stable Multi K8 (LM555) and counter 7493 N9.

The basic frequency is generated in K8. This frequency is

changed to indicate climbing or diving by a varying D.C.

input from the horizon circuit (MS at AA2). The airplane

engine sound is constructed from Fundamental and appropriate

mixing of harmonics. This mixing is done across R120. The

highest frequency comes via R117. The next frequency down is

a contribution of differentiated spikes via C35. The lowest

frequencies are added via R119 and R118. Explosion is

normally simulated by a sharp rise in break up sound with a

relative slow fading of this sound. In Pursuit, the rise is

also slow. A normal explosion is made up of 2 separate

explosions as controlled by explosion counter N7. (BB5).

  • Power Supply. Schematic Region CC7-8, DD6-8.

a.

b. Devices. (CR6 CR7) for scoring lights CR17 CR12, LM309.

Five volts is supplied by the TV chassis. The 5 volt wire

is larger than the other wires in the cable to minimize

voltage drop. For 15 volts the unfiltered voltage appears

across C42. The divider R112 and R113 changes the LM309

from a 5 volt regulator to a 15 volt regulator. Actually

it is connected as a 10 volt regulator with a +5 volt as

ground reference. This was done to increase the accuracy

of the +15 volts. A diode (CRX) is connected from +5 volts

Page 15

to +15 volts to prevent the +15 volts from being much

Tower than 5 volts at turn on. This situation could cause

lock up of the 15 volt supply. Lamp power is supplied

unfiltered from CR6 and CR7.

  • Timing Circuits. Schematic region 3 and 4 all across schematic.

a. Devices Mai Cl, Dl, D2, E3, D3, C3, B3 A3, C2 AS. p H3 all’ cs

F2i9-137 Algall’ 0’ B2 A2 8-12-10 Bary? Blary> Atay»

A new crystal frequency is used in Pursuit. This frequency

was selected because the logic functions that it generated

in division divides the screen in a much more symmetrical

way. This can be appreciated by operating the explosion

circuit and observing the symmetrical function radiants outward

from the exact center of the screen.

A ripple counter is used throughout. To avoid problems with

ripple propagation, intergate pulses BT and MF are generated

near the beginning to supply levels that occur only after

all settling has occured. The division to horizontal drive

frequency is divided by (256 x 3). There are no counter resets

required although the divide by 3 counter D2 accomplishes the

divide by 3 from the logical feedback via B23. The vertical fields are interlaced as in TV but with 544 lines per frame

instead of 525. Division for vertical and slower functions

continues through C3, B3 and A3. Wave form diagrams are

supplied for horizontal and vertical functions.

Page 16

7, Video Circuit. Schematic region DB and DD4, C4, Q5.

a.

b, The video mixing circuit picks up the various picture

components and mixing occurs at the junction of these

mixing resistors. A.C, coupling to the TV is through

C40, Q15 inserts H and V sync signals that are forced

negative TRUE. This deletes video during sync resulting

in a steady picture. A separate input to the video mixing

is provided for convenience when testing.

  • Cross hair circuit. Schematic region AA and BB 7,8 and 9.

a. Devices: Fl, Eg y2? K719

Aare Fara YBart> Blg,gs dls ATs 23 6415 C4eg> Ady a, Klaqq> Myo L3qny> Kb 45 MB y0 U4, L2, K2, Nag. Tilt since - (analog to digital).

Schematic region AAI-2

Devices E8,, £8), F7.

b. Counters L2 and K2 and J1 to H1 are compared to vertical and

horizontal timing functions to lines for the cross hairs.

Page 17

When there is no tilt, the counters are loaded at Pin 11 of

the counters. The counters being set to center number

generate only straight lines when compared to timing functions.

Jl and H1 being compared to horizontal will generate a vertical

line when the count number is center, L2 and K2 set to center

and compared to vertical functions generates a horizontal line,

When a tilted line is to be generated the counters are preset

to ZERO, (Pin 14). While L2-K2 generate the straight horizontal

line, the tilted line is essentially horizontal. N4 generates

a narrow window tin the center of the screen in which the

tilted line is to be generated. When this window opens the

counter starts to count and ti will have counted through to

256 by the time the window closes. If the cross hair tilt is

to be to the left, the count pulses are counted UP (d2). Thus

at the top of the picture the comparator writes a spot at the

left of the window. On subsequent lines the comparison is

farther and farther to the right. The result is a slanted line.

If the tilt is to be to the right, Jeg is enabled causing count down, While the counter starts at reset (ZERO), the first

count down put it at 256, and we write a line slanting to

the left. Jl and Jl generate the horizontal slanting line in

an analogous manner, except that the window is a V function and

the count H functions. Raw cross hair video is solid when there

is no slant. There is no way to avoid dotted lines when there

is slant. Therefore, to make the cross hairs consistant Flay

Page 18

Fig, K71 9» El, Elis Fl circuits are used to break up the lines for uniform appearance, and to gate out undesired portions.

  • Machine Gun Circuit. Schematic region AAS.

a.

b. Devices M7, L7, K7 M8, 18,5 F73. all’

Machine gun pulses are developed in counter, M7. V6 is counted

(1/60 second). During game time reset is released by trigger.

The audio portion of the count is decoded EM and DM at M86

(EE8) to operate the speaker, Ky 143 - L7, decodes a narrow

vertical line. 7184.13 decodes a narrow horizontal line. The AND of these signals at M8, gives Bullet Video. Bullet Video is a spot at the center of the screen. There is also a

spot at center-bottom but this is to be ignored.

  • Explosion Circuit, Schematic region BB and CC-5 and AA6.

a. Devices: N6, M6, M43 44° 46, Lag, Kae, L8_5 Pla Mai

M1 Veo F6.; FS, 6-12-8° | 8°

The explosion is an expanding window in which successively

larger blocks blink ON and OFF. The largest WINDOW is WFN3

which is a larger square taken in the center of the display.

WFNZ and WFN] are successively smaller. XFNI and 2 are broken

block functions, The above functions are multiplied in N6 and

M6 to give the expanding explosion function.

Page 19

n. Analog Motion. Schematic region AA and BBI.

a. Devices: Q7, N51 9» "8 7» E814 13° Q16, Q14, Q12, Q13 and

Random Target Motion Control: Schematic region AA and BB 1 and 2.

Devices A835 B8, BW N55 _46-g° Q4, Q3, M5156» Nay, Elgs E214.

b. The analog motion circuit outputs at H8, and H8,. The output is in the form of a DC voltage representing position on screen.

When this voltage is at about 7.5 volts (reference BB2), the

target should be at center of the screen. Comparator §844.73 and V-H ramp circuits translate the analog voltage for the

digital circuits, The analog voltages are normally always

changing. H8 and H8, being integrator will continually change in the direction of the input currents.

Input currents are supplied at H85 and H8¢ from 3 sources. Source

#1 is from the joystick pots and this arrives as the current

junction via R50 and R76. Source #2 is random motion. This comes

via R68 and R59. Source #3 is via R51 and R77 and this is pre-

dominantly bounce components intended to keep the target either

on the screen and/or to prevent the integrator from saturating.

A saturated integrator would result in a large time delay before

the target can be pulled away from the edge of the picture. The

bounce circuit is operated by changing or discharging C34 and C33,

When the target is moving around in the central area of the picture,

the bounce capacitor is charged only through R49 or R75. This is

nominally towards ZERO voltage with respect to reference, In other

words, towards "no effect", The small effect that these resistors

Page 20

have is to give motion some inertia to more realistacally simulate

real airplane behavior, At 1,2 meg, this effect is very small. -

However, if it is desired to change game characteristics, this

could be changed, When the target moves to the edge logic circuits

M5106 and F214 operate N54 to NB, for charging capacitor or N55 to N5¢ for discharging the capacitor. This action either forcefully bounces the target away from the edge or keeps

sufficient charge to the capacitor to prevent integrater saturation.

If integrator saturation is prevented, random motion summary

current will certainly sooner or later push the target back towards

center. This is more important in attract than in game because

in game the joystick is used to pull the target to the center.

Neutral voltage at the joystick pots during game time should be at

the reference level, hence giving no motion bias. At mechanical

neutral, the resistance on each side of the arm is unbalanced at

1K and 4K, Balance is recovered with on board pots connected on

the low resistance side of each hoystick control, These pots are

used for compensating all game time off center bias. At attract

time the control pots are disconnected by conduction of Q7. At

this time centering of both borizontal and vertical target motion

is done with the 250 ohm attract center pot. Random motion is always

imparted to the target by current inputs to the summary junction

via R65,64,61,63,66 and 62. For each of horizontal and vertical

the values are roughly in the ratio of 4-2-1, giving a D/A conversion

of the digital inputs from 08, . Voltages higher than reference

give down or right motion, whereas voltages less than reference

give up or left motion, The most significant bit from D810 or 08,

is essentially the direction bit. Random digital input to D8 is

Page 21

12. obtained from B8 (74164) which is a serial in parallel out

8 bit shift register, The input to the shift register is

oscillator 83. The shift register is advanced about every 2

seconds. The value that happens to be at the input at shift

time is the value that is shifted through the shift register.

Since advance time is asynchronous with respect to the free

running oscillator, the value at this time is random. As the

bit shifts its significance charges allowing the total change

instructed to also be random.

Digital Motion Circuit. Schematic region DD and EE1.

a. Devices: Ba Ea Foy 510° H5, J5, H6, L5,.

b. Prior to a compare of DC input, H8, with a ramp at E8q the output at F814 is down, This down condition holds 05,3 (latch) up unconditionally. When E814 rises upon detecting compare , 0513 is enabled to come down, but it will not do

so until DT comes down. DT is a negative going signal of 25% duty cycle that is exactly out of phase with MF. Since

detection of compare can occur only at a synchronous condition

with DT an interface is established from the analog signal

which can occur at any time to a synchronous system that has

forbidden times,

The negative signal is transmitted through E53 to release latch D5g and to DS). At that time both 1 and 2 of E5 are up giving a negative output at E5., This negative condition

is quickly terminated when D5g is reset by MF.

Page 22

The overall result is a very short negative pulse guaranteed

to occur at compare. This negative pulse resets HT window

counters H5 and H6, which count through once. Count is

stopped by a down Condition at K5, (The most significant

bit of the counter). While counting through the target functions are generated, The generation of the vertical

target function is completely analogous,

  • Target form circuits, Schematic region DD and EE2.

a.

b. Devices: Maw Ba Fay 10,4 Fl, Oa Ma Aba» Keg a1:

Wings, body and fins are ORed at 4, 3, and 5 of C5 respectively.

Gate Abs is disabled during explosion (A619) to cause target to disappear for a moment.

  • Horizon, Schematic region AA and BB2.

a.

b. Devices: H8,, H8,4-

The vertical joystick voltage is amplified by H89 and compared

to the vertical ramp with HB, 4- R73 and R74 give hysterisis to

smooth transition when a change of direction occurs. The step

function generated at 1844 is the horizon voltage. The changing

voltage at H8, is used to change motor sound.

Page 23

G. SETUP PROCEDURE

  • Instruments Required

(a)

(b)

(c) Watch or clock for timing.

Micronta 22-205A 20,000 ohm/volt meter or equivalent

Mirror to observe screen while adjustments are made at board.

  • Motion Centering Adjustment

(a)

(b) Make sure adjustment tabs on each of the joystick pots

are centered and secured. We use RTV to secure these tabs.

Center the joystick mechanically. This should be the

position to which spring loading holds the joystick.

Adjust H balance on board until titere is ZERO volts between

reference junction R39-R40 and the H control arm. Use a

Micronta meter on .5 volt scale.

Same as (3) except on V joystick pot.

While meter is connected between V arm and reference, turn

game OFF (interrupt power), and adjust ATTRACT center control

for ZERO volts.

Using clip leads short C27 and C24.

Adjust V and H ramp to center target. Explosions will occur

but position can still be observed in at least half of this

sequence.

  • Extended Play Adjustment

The extended play switch is located at P6 on the PCB. It isa

4 pole DIP switch. Each of the poles enables extended play at

the skill level of:

Page 24

2.

3.

4. Wash Out

Eagle

Note reversed sequence Student Pilot

Ace

If all switches are OFF no extended play occurs. Only one switch

should be ON at a time,

  • Game Time Adjustment

Location: About D6 on board.

Orientation: Face is from top of board.

Adjustment: Clockwise increases game time.

Range: 1/2 minute to 3.5 minutes.

  • Sound (Volume Control)

Location: About N9

Orientation: Facing is from top of board.

Adjustment: Clockwise to increase volume.

Page 25

H. PRODUCTION BOARD TESTS

  • Instruments Required:

(a)

(b) Oscilloscope

Test station with display and analog controls.

  • Suggest logical sequence of investigation. A given circuit cannot

be assured of work until all that is before it has been confirmed

to be functional. (Can be changed as experience dictates).

(a)

(b)

(c)

(d)

(e)

(f)

(gs)

(h)

(4)

(5)

(k)

(1)

(m)

(n)

(0)

(p)

(a)

(r) Power Supply

Timing chain to Pix Sync.

Game Time circuits

Analog input adjustment

Confirm proper analog motion as varying DC at H8 1 and 7.

Confirm H and V ramp at E3 9 and 11.

Confirm H and V "step” signals at E8 14 and 13.

Trigger pulse should exit at E53 all These pulses are

very short and at E514 may be difficult to see. Check for H and V window at HO6, and Ls,. Check for structure of target body through to video.

Check for porper motion of target in response to control

input and random motion input.

If no random motion check oscillation AB, and shift register B8.

If target sticks check H and V bounce circuits.

Horizon video.

Bullet circuits

Explosion couter L6, to N7. Explosion video.

Explosion sounds. If more check audio.

Page 26
  • Motor sounds, If more check audio.
  • Audio output.
  • Machine gun sounds.
  • Cross hair circuits.

NOTES

  • R110 on PCB provides a video input point so that circuit may be

probed in the video display mode. This point is at E10 and is

marked "TP".

  • Balance control must be adjusted to match the test station analog

controls. See setup procedure. This setup procedure must be repeated

later with controls used in actual game.

Page 27

. MOTOROLA MONITOR

Monitor circuitry includes four stages of video amplification - a two

stage audio amplifier, sync and deflection circuits, and a regulated

power supply. An additional 5 volt supply is included to power the

external logic system. The rear panel controls work as in any normal

T.V. - vertical, horizontal, brightness and contrast. The vertical

and horizontal controls should be set in the middle of their range.

Turn control until picture tears or rolls, turn control back until

picture tears or rolls in the opposite direction and reset control in

the middle of the stable range. The brightness and contrast should be

set at a point where the ‘mages on the screen do not smear. Additional

controls are mounted on the printed circuit board (PCB) and are

accessible from the rear of the chassis. These include vertical size,

vertical linear, focus , etc.

  • Five Volt Supply: This is located on the power, audio PCB which

is on the left side of the monitor in back of the power transformer.

There is a 1,000 ohm trim pot to adjust the supply voltage. This

Measurement should be made on the logic PCB to allow for voltage

drop from monitor to PCB.

  • Regulator Adjustment: Connect monitor to AC line supply. Adjust

horizontal and vertical controls until display is synced. Connect precision voltmeter to any of the 73 volt test points and adjust

regulator control R74 on circuit board for an output of 73 volts.

CAUTION: Do not run the regulator control through its range or damage to the monitor may result, All that needs to be done isa

slight turn to adjust properly. Both the 5 volt and 73 volt

adjustments have been made at the factory and under normal

Page 28

conditions should not need readjustment.

The Yoke: The yoke should never need adjustment unless the

adjusters have been tempered with or the machine damaged. If

yoke adjustment is indicated, adjust both yoke rings simultaneously

for optimum centering of the image on the CRT, This adjustment is best handled by a qualified service person,

A.C. Voltage Switch: Set this switch to the 115V position ("115"

visible on the switch) if the machine is connected to a 115V source

or to the 230V position ("230" visible on the switch) if the machine is connected to a 230 volt source. The T.V. monitor will

not function if this switch is misadjusted, NOTE: If the monitor

of a 230 volt machine is set to 115 volts, it will blow the

machine line-fuse repeatedly.

The T.V. Monitor Fuse: One 6/10-amp, 250-volt fast-blo fuse

protects the T.V, from electrical overload (for 155V operation, the

T.V. fuse must be 1-amp fast-blo.) Replace blown fuses with ONLY

those which have the above rating. This fuse is located on the

electronics mounting board inside the rear door. The fuse furthest

from the door is the T.V. fuse, and the fuse nearest the door is

the P.C.B. fuse. The P.C.B. fuse should be replaced ONLY with a

one-amp, slo-blo, 250-volt fuse.

Monitor P.C.B. Removal:

  • Power, Audio PCB: Locate board on the left side of the

monitor in back of the power transformer, To remove, pull

board up. To replace board, locate the slot between pins

3 and 4 and put this on your left side, then simply insert

into the connector.

Page 29
  • Monitor PCB: To remove the monitor PCB take a screwdriver

or similar object and slowly pry the PCB up off of the chassis

until it clears the pins. Next, unplug the socket from the

yoke and slide board out. To replace this board, follow the

above steps in reverse order,

The monitor can be removed by way of the rear access door of the

cabinet. This door also provides access to the logic PCB,

transformer assembly, score light PCB and main harness connectors.

CAUTION: Any work performed on monitor chassis should be done

only by qualified service personnel who are familiar with

servicing procedures and precautions,

J. Q-530 COIN ACCEPTOR: OPERATION, ADJUSTMENT & MAINTENANCE

1. Adjustment: All coin acceptors leave the factory adjusted for

maximum performance, If, however, more critical adjustments are

desired, or if the unit has been completely disassembled for

service, the following adjustment procedure is suggested. If

the coin acceptor has been removed from the machine, place it in

a vertical position on a level surface. If the acceptor is still

mounted on the coin door, place the coin door in a vertical

position on a level surface.

Kicker and Separator

  • Set the acceptor with the back of the unit facing you in the

test position.

2, Loosen the screws holding the kicker (1) and the separator (3)

and move both the kicker (2) and the separator (4) as far to

the right as they will go. Tighten the screws.

Page 30

10. Insert several test coins (both old and new) and note that

some are returned by striking the separator.

Loosen the separator screw and move the separator a slight

amount to the left. Tighten the screw.

Insert the test coins again and, if some of them are still

returned, repeat Step 4 until all the coins are accepted.

Loosen the kicker screw and move the locker as far to the

left as it will go. Tighten the screw.

Insert the test coins and note that some are returned.

Loosen the kicker screw and move the kicker a slight amount

to the right. Tighten the screw.

Insert the coins again and, if some are still returned,

repeat Step 8 until all the coins are accepted.

Be sure that both screws are tight after the adjustments

have been made.

The Magnet Gate

1. Set the acceptor with the front of the unit facing you in

the test position.

Turn the magnet gate adjusting screw (2) out (counterclockwise)

until none of the coins will fit through.

With a coin resting in the acceptor, turn the adjuster in

(clockwise) until the coin barely passes through the magnet gate.

Test this adjustment using several other coins (both old and

new) and, if any of them fail to pass the magnet gate, repeat

Step 3 until all the coins are accepted,

Fix the magnet gate in this position with a drop of glue or

lok-tite, if necessary.

Page 31

Acceptor Maintenance: Depending on the environment in which the

acceptor is used, periodic preventitive maintenance should be

performed. The mainplate (5) may be cleaned with any household

cleaner, Thorough rinsing and drying are necessary to remove

deposits and/or film. Remove all metal particles from the magnet

by guiding the point of a screwdriver or similar tool along the

edges of the magnet. You will notice that the particles will

cling to the point of the tool. Remove the transfer cradle (9)

and the undersize lever (10) and clean the bushings and the pivot

pins. A pipe cleaner is an effective cleaning tool. Apply

powdered graphite or pencil lead to the pivot pins and bushings

and reassemble. Spray the entire unit lightly with WD-40, a

silicone lubricant,

. GENERAL MACHINE MAINTENANCE

Due to its solid state circuitry, your Pursuit will require very little

maintenance other than periodic cleaning, lubrication and T.V.

monitor adjustment. The cabinet and plexiglass screen may be cleaned

with any non-abrasive household cleaner, The coin acceptor and the

rejector linkage should be sprayed lightly once every three months with

WD-40 or similar silicone lubricant. The potentiometer shafts must

never be lubricated in any way. The T.V. monitor is adjusted only when the CRT picture is distorted, or if the contrast or brightness

appear to be out of adjustment,

Page 32

~ TROUBLESHOOTING

The first step in any troubleshooting procedure is to identify the

observable characteristics of the malfunction. With these clues in

mind, examine the areas of the machine which might cause these symptoms,

For example, if there is no power, check the harness - not the PCB.

Likewise, if part of the playfield display is missing, check the PCB -

not the harress cr TV.

Three major areas of the machine can be isolated for troubleshooting

purposes: the T.V., the PCB and the harness. The harness includes

the fuses, the transformer, the interlock switches, the A.C. line

filter, the start and coin switches, the antenna wire, the potentiometers,

all plug-in type connectors, the PCB edge connector and all the

interconnecting wires.

  • Substitution: Substitution of parts is a legitimate and easy way

to troubleshoot the machine. For instance, if you suspect PCB

malfunction try substituting another and known-to-be-good PCB.

To check the T.V. monitor by substitution, connect the malfunction-

ing game to a known-to-be-good monitor. Harnesses are checked

by elimination. Substitute a good T.V. and PCB and if the

malfunction persists, the harness must be at fault.

  • Other Troubleshooting Tips: If you have a T,V. raster only

(a T.V. raster is a blank, but lit T.V. screen with the brightness

turned all the way up) and you want to determine if it is the

PCB or the T.V, that is causing the lack of video display, try

the following test: (A)disconnect the PCB edge connector;

(B) turn the brightness and contrast all the way up; (C) connect

pin 11 of the PCB edge connector to pin 12 with a test lead. If

Page 33

your T.V, monitor is functioning correctly, you will see faint

black bars ("hum bars") on the screen,

TO CHECK THE SPEAKER, turn the colume control all the way up,

and connect one end of a test lead to pin 2 (audio) of the

disconnected PCB edge connector. Momentarily touch the other end to either pin 3 or pin 4 (transformer secondary AC) of the

edge connector and if the speaker is functioning correctly, you

will hear a loud buzz (60 cycle hum), To check if the TV POWER

SUPPLY is functioning corrctly, use the following procedure:

check the T.V. power supply output between pin 6 and pin 8 with

a VOM, Meter should read 5 volts OC,

Troubleshooting by Symptom:

  • NO POWER: a. check for correct line voltage and if OK

then check fuses and interlock switches. If OK, check

transformer primary which should show line voltage. Then

check transformer secondary (pins 19 and 21) which should

be 10 VAC.

  • GAME CREDIT SHUTS OFF: Try cutting the antenna wire shorter

in increments of 1-2 inches.

3, GAME CREDIT SHUTS OFF AND/OR T.V. PICTURE SHRINKS: Check

line voltage with VOM and be aware that a large motor

nearby (e.g. air conditioner) may drop line voltage when

starting up.

  • NO PICTURE; NO RASTER: Check to see if T.V. connector is

plugged in; check for line voltage at T.V. and if T.V. AC

voltage switch is set to correct position. Check T.V. fuses

and brightness control.

  • 1.V. RASTER ONLY: Check harness and especially the PCB edge

=31-

Page 34
  • PICTURE ROLLS: Adjust T.V. vertical hold. Check or replace PCB.
  • PICTURE IS WAVY: Adjust T.V. horizontal hold. Replace

transformer, Check harness, particularly grounds.

  • PICTURE IS BROKEN INTO DIAGONAL LINES: Adjust T.V. horizontal

hold. Replace PCB.

  • JERKY PLANE MOTION: Replace appropriate potentiometer.
  • NO GAME CREDIT: Check coin switch and harness. Replace PCB.
  • GAME SEQUENCE INCORRECT OR PARTS OF PLAYFIELD DISPLAY MISSING,

DISTORTED OR NOT FUNCTIONING: Replace PCB.

  • NO AUDIO: Check volume control, speaker connections.

Replace PCB.

DIAGNOSIS:

SYMPTOM CHECK

No picture Power cord, harness connections, line and monitor fuses.

No sound Speaker connections, volume adjustment

Rolling or tearing picture Readjust T.V. controls connector. Check PCB. Check T.V.

White picture but no display Edge connector on logic PCB, 5 volt supply from monitor, 12 pin Molex connector on monitor.

Wavy Picture 5 volt supply, 73 volt regulator adjustment

Game will not start Coin mechanism, harness connections

No Firing Joystick, harness connections

NOTE: If the above checks do not solve the problem, consult the

appropriate theory of operation description of the logic PCB circuits.

Page 35

+ __P.C.B, SHIPPING

Careful packing of PCBs and other parts being returned is recommended

as we cannot be liable for items damaged in transit. If possible,

include a short statement describing the problem encountered with

the game.

Page 36

EGS IDS eer snsen— KICKER SCREW KICKER SEPARATOR SCREW SEPARATOR MAINPLATE ASSEMBLY GATE ASSEMBLY COVERPLATE ASSEMBLY RAIL CRAOLE ASSEMBLY UNDERSIZE LEVER MAGNET GATE ASSEMBLY MAGNET GATE ADJUSTER SCREW LOWER GATE PIVOT SPRING UPPER GATE PIVOT SPRING GATE PIVOT PIN WIPER LEVER SPRING WIPER LEVER WIPER FIGURE D: COIN ACCEPTOR - EXPLODED

ar FIGURE C: COIN MECHANISM — EXPLODED

Page 37

area fr ATED I F Innovative a Checked Proj. Eng.-t-----;, -

DARRWNHOWDNARGOHWN DESCRIPTION

002780 4002783 002784 002809 002786 A002781 73-02-08 78-2622 71-5203 75-666 75-S616h 75-991102 75-943 75-5512N 75-915S 75-045 PTT CC Ci ee ee ey Joystick - Final Assy Shaft Weld Assy Mounting Plate Stop Mounting Bracket Kraft joystick Assy Cotter Pin 1/8 dia x 1/2 long Grommet Links of chain - Stl, Single Jack #12- 2-1/2" long Sheet Metal Screw #6 - 3/8 long Carriage Bolt 5/16-18 x 1 Nut 5/16- 18 Split Lock Washer - 5/16" Carriage Bolt 1/4-20x3/4 Nut 1/4-20 Lock Washer 1/4

Page 38

Innovative leisure

Part Number

A002869 002804 002882 002870 A002871 A002780 002878 73-7401 75-5520N 75-0158 75-045 75915S 75-5132N 75-9118 75-0146 75-040 A002807 A002808 A002879 75-2124S 75-9118 75-014C 75-050 75-7606 Fo] a HNENMH BHABHA ADEHAHOP SSH HAHD DESCRIPTION

Cabinet Final Assy Cabinet Upper, Formed Panel Assy Flourescent Light Assy T.V. Mounting Assy Joystick Assy Double Coin Switch Assy Southco Rivet #38-106-30-13 Carriage Bolt 1/4-20 x 1-1/4 Plain Washer 1/4" Lock Washer 1/4" Hex Nut 1/4-20 Carriage Bolt #10-24 x 2" Hex Nut #10-24 Plain Washer #10 Lock Washer #10 Harness (Sub) Harness (Main and Sub) PCB Tray Assy R.Hd. Mach, Screw #10-24 x 1-1/2 Hex Nut #10-24 Flat Washer #10 Lock Washer #10 Sht. Metal Screw Pan Hd. Phil. #6 x 1"

Page 39

t : Innovative leisure Proj. Eng. i°° P/L 002490;

Page 1 of 3

Mech. Eng.

tytn Elec. Eng

Description Apprv.t Rev. seve] BRST

37-7400 37-7402 37-7404 37-7405 37-7406 37-7410 37-7420 37-7427 37-7442 37-7474 37-7486 37-7493 37-74107 37-74132 37-74153 37-74164 37-74193 37-74279 37-555 37-741 37-L339 37-LM324 37-3080 37-LM309K 37-LM380 10-02P7

10-0220 10-0101 10-0181 10-0221 10-5331 11-5331 10-0331 10-0471

10-0561 10-0102

10-0563 10-0122 oo NwUIN POND

ee ern CER ene Ce Ste Ey

aN RE DWH NNN Cc Cc c c Cc Cc Cc, c c Cc c c $s esis 7400 7402 7404 7405 7406 7410 7420 » 7427 » 7442 7474 7486 7493 74107 74132 « 74153 » 74164 » 74193 . 74279 » 555

. LM339 « LM324 + 3080 RCA « LM309K LM380 tor, 27

K

56K 1.2K ohm, 1/4 watt, 10%R125 Description

"R101 "R120. " R37, 54 " R39,86, 5%R39,R40 5%R112 103R3,R2 "'RO7,R32 . ,RB3,R84,81, 109,110,111 “R79, 94 60 ,67 *R107,38,10,104,85,27, | 28,1,18,55,90,15,,124,80 "R21 ,23 ae \ "R70,71,57,58 69,78 ,56 |

Page 40

ASSEMBLY TITLE PURSUIT P/L 002490 _ —— S_LIST SPECIFICATION ||oaze 2 of 3 [iten| Part sunber _[aty.] DESCRTPTTON . 10-0222 Resistor, 2,2K ohm, 1/4 watt,10%, 92, .,16, 9,108,105

10-02722,/K *"™ R31,41,42,74,95,

35,36 ,17,32,100

11-522122025% R113
10-03923 9K74R119
10-04724.7K"R93,102,103
10-05625.6KR47,91,3118

44572

0-06826.8KR11
10-08228.2KR117
0-010310KR87 83,106, 96,98,

99, 43,73

10-0153 10-0223 0-0333 15K R68,19,22,59, 22K R13,R24,R26 33K R25,48,52, 12,20

0-5563 10-0823 10-0104 56K R46 R44

82KR53-

100K R29,30,51 ,77,121°

150K R7 RS 470K R33 34 390K Ri, »76" 560K R1Z,R14 680K ye 1 meg R63 ,65,6,5 7 R75,49 " R64 ,66 " R62 61 Transistor, NPN, 2N3643 7 PNP, 2N3644 C26,27, 12 Diode, 1N914 C4,21,20,38, Diode, 1N4001 C19,23,22,47,2, Capacitor, .luf, +80%,-20% Ceramic\c15,16,9, 3, 25, ” +20%, 12 volts,C24, C28" " #80%,-20%, 25vol ts, Cat, 46,8 .Oluf,+80,-20%,Cer,C17,1,30,35,15,14 .O0luf ,t10% ,100v,C32,C11,7 .22uf,+10%,Mylar, C31,29 220pf, Ceramic Disc,10%,C5 100pf, Ceramic Disc,10%, C45 4.7uf,25v, +10%, Electrolytic, C6 l0uf ,25v,Electrolytic,C10,33,34,18 luf ,25v, Electrolytic ,C44 ,36,37 50uf, 25v, Electrolytic,c40

500uf, 25v,:C48
100uf, 6v,"C39

10-0154 0-0474 10-0394 10-0564 10-0684 0-0105 10-0125 10-0225 10-0395 34-2N3643 34-2N3644 31-1N914 31-1N4001 27-120104 29-008 27-250104 27-101103 29-009 21-101224 28-101221 28-101101 24-250475 24-250106 24-060105 24-250506 24-250507 24-060107 DAY VNNFHNYNANY NHN Awe

we See w Foo aN won se

24-250478 4700uf, 25v,GMV Nichicin N7419 or equiv,

19-311105 Pot, 1 meg, CTS x201 R105B

Page 41

ASSEMBLY TITLE PURSUIT P/L oo2us0 __PARTS LIST SPECIFICATION IJrage 3 of 3 | | part Number _|oty. | DESCRIPTION Rev _D

19-311502 19-311104 66-02 19-311251 002743 75-2601S -75-056 78-016S 75-916S 12-0101 38-MV5013 10-0274 Pot, 5K, CTS x201R502B Pot, 100K, CTS x201R104B Dip Switch, Molex 4130 #01-70-0104 Pot, 250 Crystal 12,096 MHz Screw, 6-32 x 5/8", Pan Hd., S.S. Washer, Internal Star Lock, #6 Washer, Flat Nut, Hex, 6-32 Resistor, 100 ohm, 1 watt, 10% LED, MV5013 Resistor, 270 K ohm, 1/4 watt, 10% SBHe@4nnnn 777

Page 42

MOD © MOD It

D

Weth

Welt MOD 10. DEScEIPTION peta [ARV a Ns D [Gav een eon 106, ISTE ‘i. fal

MODIFICATIONS 5 |. CHANGE REO € BGT FROM 5.6K TO Sedn.

  • ADD INGOOL BETWEEN +ISV % 45V , CATHODE TO +I5V,
  • ADD LED IN SERIES WT B3O.n RESISTOR BETWEEN HEV 2 GHD. 4, DELETE 1.¢. AS (7493), S. JUMPER PIN 1 TO PIN I4 ON AB 1. PATTERN. ©. CHANGE RIB FROM 2.2% TO IK.
  • ADD 160.2.,1W RESISTOR IN EXISTING HOLES NEXT TO cei2, ©, DELETE. HEATSINK FROM LM3OS. @. DELETE THE FOLLOWING COMPONENTS + as ~ 250mF A. Bar - 2NBeAS co. ce - INDIA D.cel - IN4eor &, cee -INDIGA Fee 1K Gene + 1S 4, RNS ~ 1002 tr. Lid - Rear
  • ADD SOMPER. BETWEEN WIPER AND NLC, OF RELAY PATTERD, I. ABD 27OK RESISTOR FROM M& PING TO Cw. SIDE OF loon Par.
  • COT TRACE, AS SHOWN, ABIACENT TO KS £15. 20N ALMPER. FROM TRAE TO 1.¢.LG PINS, 1B. AOMPEe LEADS OF 2121 € 2IZ2 NEAREST IOOK POT.

BP-A PRSvIT fev. D KEE GAMES INC. ASSN. W000 WINCHESTER BLVD. LOS GATOS CA. 45030 @o8) 274-2440 A

scate: i pepe: DATE: nT H ton Jyprord P.BRISTOND Cais 7 DRWe.NO. AOOZ49 0 _

Page 43

euler TRIGBER, a po Explesim Coster Exptesan Matt a n

EOSIN VIDEO

te

ql 8 i sie TGP Me cxoss wait vineo

fe rf TRIAD FaOX es 43627 f 4001 cA ans) (AAS) (GSE) (EMPLosioN DISABLED (st) (GAME Time) aod BPQINTS

nee

e+ POINTS

PG.1OR2

aw PATE

330 MATHEW ST SANTA CLAGA CA

002490

Page 44

omiecr DRIFT Rew DIGITAL MOTION

gov sven. Tor view TO (cr o1eecTioN) Boe V. BOUNCE, VT winvow S2NT

Te (reser Bony) ah

HORIZON VIDEO

IR GOES UP fin coEs ve os a

TIMING FUNCTIONS ALL J 3, Pigye Tarr vse ep (ens)

fos Lys “483, 493 ia

v s

vw TPP a0 so w 1 sos — AS oe T,

7 —_

ot

TEST POINT (TP)

(ARB) CROSSHAIE, WIDE

nS) GULLET vInEo (WDE) SCORE VIDEO (OBZ) MORIZON VIED (Eb) FUEL DED. (een) ET VIED — aaa

(CES) EWPLOSION WibEO—4 wr | OF “ohare he,

Video Mixing, dumper 73 ner wo

3S WAT HED 3 SAUTR CLAGR 1

Page 45

SPEAKER 22 PIN EDGE KI 16- OHMS + 1 CONNECTOR _ CONNECTOR _ —. ac POWER, 268VcT - En a oo Tea TRIAD FUSE

F-40x SCORE-DISPLAY LIGHTS

I : OOF Ext Ls | IG PTS Ey I2PTS a a eae 0 Se 31 @-@44 PTS JOY-STICK 10 PIN EDGE BULLET-TRIGGER CONNECTOR

ry

0 eo 87 TV COIN MECH 2 95 98 all CONNECTOR | sp 8

VIDEO

FLOURESCENT—LAMP

COIN COUNTER

14600 Winchester Boulevard

ATARI Los Gatos, California 95030

pat elee ™K8P-PURSUIT ELI 12-374 ee

ELECTRIC- HARNESS DWG es es Co Decree ere

nmi Fl

Page 46

‘DESCRIP eben

© a

sHarT Assy-pusus 4002783 E))

MTG. PLATE M2 OOZ784

CARRIAGE BOLT 2-18, /'LONG Ores acim ; : SaTH Lock WASHER? adr (2 REG CI) $208) coremes 2 : CB 7-20 HEX. wuT s = Corre FIM Zax EL. 4 * $1 nex wor (8) cont —sivace sre JAC “18. CD) i CHAIN Stu.Sincus dace #72 [BRACKE 1-DWG.N? 002786 COTTER PIN goin X Ven. 4-20 x} CAREIAGE BOLT| 4g LOCK WASHER Z-20 HEX NUT risen ALD ti NNTS PLATE C264 27) LOCK WASHER- Sg KEAFT yor sricK Assy. ; HEX NUT Go-/8 Cit le eae TSHEET METAL SCREW “= ¥e oozses | STOP 262781 | KRAFT JOY STICK MODIFICATIO: (002766| BRACKET 5

CARRIAGE BOLT Z-78x! 4062763| SHAFT ASS'Y. Dws We | DESCRIPTICA WISERT Wheto WIRE INTO PIN") HOLE ¥ BACK VIEW SIDE VIEW — GAMES, ware de WIRE INTO "& HOLE JOY STICK HARNESS 002807 -~0F 12s mmm 1 loy STICK WIRE DETAIL Ditz.A00ZBO7-O3 e USUI T FINAL ASSY- JOY STICK