Alien Storm
Alien Storm (World, 2 Players) (FD1094 317-0154) (Sega, 1990) · Manual · 13 pages · 11 sections · original scan
ALIEN STORM |
3 PLAYER UPRIGHT
SEGA ENTERPRISES, INC
ALIEN STORM
by:
SEGA Enterprises, Inc. (U.S.A.)
2149 Paragon Drive San Jose, California 95131 Phone Number (408) 435-0201 FAX Number (408) 435-0294
SPECIFICATIONS
INSTALLATION SPACE : 25.5 INCHES X 33 INCHES HEIGHT > 76.5 INCHES
POWER + 250 WATTS WEIGHT + 209 POUNDS
DISPLAY TYPE : 19 INCH COLOR MONITOR
The Federal Communication Commission requires the verification of game kits. This game meets these requirements when installed in accordance with the instructions in this Manual and using only components and materials supplied.
Table of Contents
Introduction 3 Handling and Installation Precautions 3 Prevention of Counterfeiting and Conversion Labeling 4 Precautions Concerning the Place of Installation 5 Cabinet Diagram 6 Opening the Control Panel 7 Service Switches 8 In Case of Difficulty 9 Monitor Adjustments 10 Switch Setting Sheet 11 Schematic Diagram 12
INTRODUCTION OF THE OWNER’S MANUAL
SEGA ENTERPRISES, LTD., supported by its high electronic technology of LSIs, microprocessors, etc. and a wealth of experience, has for more than 30 years been supplying various innovative and popular game machines to the world market. This OWNER’S manual is intended to provide detailed comments together with all the necessary information covering the operation in general of electronic assemblies, electromechanical servicing control, spare parts, etc. The manual is intended for those who have knowledge of electricity and technical expertise especially in ICs, CRTs, microprocessors, etc. Carefully read so as to acquire sufficient knowledge before working on the machine. Should there be a malfunction, non-technical personnel should under no circumstances touch the interior system.
HANDLING PRECAUTIONS
When installing or inspecting, be very careful of the following points and pay attention to ensure that the player can enjoy the game safely.
o Be sure to turn the power off before working on the machine. o To insert or pull out the plug quickly is dangerous. 0 Itis necessary to make sure that the power cord or the grounding wire is not exposed on the road, etc. in a manner so as to be dangerous. Make sure that grounding connections are made safely at the position where specified. o Do not use any fuse that does not meet the specified rating. o Make complete connections for the IC board and other connectors. Insufficient insertion is very dangerous.
Also, for the IC board circuit inspections, only the logic probe is allowed. The use of a tester is not permitted, so be careful in this regard. After confirming that there are no irregularities, turn the power ON.
if PREVENTION OF COUNTERFEITING AND CONVERSION
LABELLING To prevent counterfeits and conversions, the following labels are put on all the SEGA products. When handling such goods, be sure to confirm the labels. They are used to prevent illegal acts such as the unauthorized copying of the products and the printed circuit boards thereof or carrying on business by manufacturing similar merchandise or by converting, selling or using such products or printed circuit boards.
The following seal is put on the machines manufactured by SEGA
A a te ato
AUDF IVE ORIGINAL SEAL, “Was mooUcT SoScaeD AD HARE ACTRED try av SECAEMERPARES LID nl sn i th seo te area ee Tere ee
ORIGINAL SEAL
COPYRIGHT NOTICE This SEGA product has the copyright notice as follows:
© SEGA 1990
This signifies that this work was disclosed in 1990 and is the property of SEGA ENTERPRISES, LTD.
PRECAUTIONS CONCERNING THE PLACE OF INSTALLATION
This is an indoor game machine. Absolutely do not install it outside. Even indoors, avoid installing in places mentioned below so as to ensure proper usage:
cooooooo 8 Places subject to rain or water leakage, or condensation due to humidity. In the proximity of an indoor swimming pool and/or shower. Places subject to direct sunlight. Places subject to heat sources from heating units, etc., or hot air. Vicinity of highly flammable/volatile chemicals or hazardous matter. Sloped surfaces. Vicinity of anti-disaster facilities such us fire exits and fire extinguishers. Places subject to any type of violent impact. Dusty places.
MARQUEE LAMPS, 2EA 40 WATT ie INCONDESCENT
8 OHM 10W SPEAKER, 2EA 880300600 “4
19" COLOR MONITOR, 200-5095
SIDE DECAL RIGHT 999-0008 |
MONITORGLASS ———~} 861100800
PLAYER JOYSTICK MARQUEE PLEX rm SC«éS-0NB
MONITOR BEZEL D851101000
SIDE DECAL LEFT ra 999-0008
CONTROL PANEL OVERLAY 999-0019
PLAYER BUTTONS 509-0001-01
STICKER 3 PLAYER 999-0020 509-0004-01 RED 509-0004-02 WHITE 509-0004-03 BLUE 509-0004-04 YELLOW
3 COIN ENTRY DOOR
OPENING THE CONTROL PANEL FOR SERVICE OR TO GAIN ACCESS TO THE PC BOARD AREA.
To open the control panel and gain access to the PC Board for maintenance or replacement follow these procedures:
o Open the Coin Door, and disengage the 2 Super Clamps holding the control panel. This can be done by putting your arm through the coin door opening and reach up to the upper right hand corner of the control panel and un-latch the super clamp. Repeat this process for the clamp in the upper left hand corner.
o Toremove the control panel, remove the four bolts on the hinge that hold the panel in place, and disconnect the control panel harness.
o To gain access to the PC Board remove the cover of the RFI cage by pulling upward on the Ny-latch fasteners.
SERVICE SWITCHES
Open the COIN CHUTE DOOR, and the following SERVICE SWITCH layout will appear:
SERVICE TEST
- SERVICE SWITCH
- TEST SWITCH
- VOLUME ADJUSTMENT sw gw. SP VOL
3 - VOLUME ADJUSTMENT
2- TEST SWITCH
1 - SERVICE SWITCH
Used for the purpose of servicing and increasing the credits without registering on the meter (this allows you to check the game).
For the operation of this switch, see SELF- TEST.
Used for adjusting the volume of the speaker.
In Case of Difficulty No Raster/No Video -Check A.C. line cord -Check line fuse -Check monitor brightness -Check power switch and/or interlock switch -Check all solder connections on line filter and transformer -Check for proper orientation of the 56 pin PCB connector Raster/No Video -Check all PCB to monitor connections -Check power supply voltage on PCB No Video/ Game sounds can be heard -Check monitor brightness -Check all PCB to monitor connections Incorrect Colors -Monitor needs degaussing -Check for proper wiring between PCB and monitor -Check monitor adjustment and adjust if necessary Wavy Picture -Check monitor ground is properly connected to monitor -Be certain sync inputs are properly connected to monitor -Check horizontal hold adjustment Vertical Roll/Horizontal Tear -Check horizontal and/or vertical hold adjustments -Check for proper wiring of sync from PCB to monitor No Sound -Check volume control potentiometer adjustment -Check for + 12 volts on edge connector of PCB -Check wiring from PCB to speaker -Check speaker for low resistance between the "+" and" -" tabs Bad Sound -Check wiring to speaker for bad solder connections -Check sound with another speaker No Switch Input -Check ground connection to switch/es -Check wiring between PCB and switch/es for proper connection -Check switch/es with an ohm meter to verify proper operation Switch Operates Incorrect Function -Check wiring between PCB and switches for proper orientation -Check wiring for shorts between switch inputs No Coin Meter -Check wiring to coin meter -Check that + 5 volts is on + side of meter -Verify a + 5 volt meter is used When coin switch is made and meter pulses, the screen blanks out and/or game resets -Verify that a meter with a diode is used -If no diode is built in meter a 1N4004 can be used across the meter. Cathode to "+" side of meter and anode to "-"side of meter.
GREEN DRIVE
@LU CUT OFF HORIZ SIZE GREEN CUT OFF
RED ORIVE
REO HORIZ RASTER CUT OFF POSITION
FUSE
% ‘ ~V.SYNC
Focus” ; ~H.SYNC SCREEN v. q HORIZ uipee . +H. SYNC HORIZ HOLD ey SYNC
VERT RASTER POS VERT SIZE
VERT HOLD BRIGHTNESS
BLUE BLUE ORIVE CUT OFF
GRN ORIVE
GREEN CuT OFF
RED DRIVE HORIZ RASTER POSITION
FUSE
Focus SCREEN HORIZ VIOEO. SHIFT HORIZ HOLO VERT RASTER POS VERT SIZE VERT HOLD BRIGHTNESS CONTRAST
MONITOR ADJUSTMENTS
_ ALIEN STORM
DIP SWITCH ASSIGNMENT
[COIN / CREDIT OPTION SWITCH SETTING
2 CREDITS 1COIN 3CREDITS 1COIN 4CREDITS 1 COIN 5 CREDITS 1COIN 6CREDITS 2COINS 1 CREDIT 3 COINS 1 CREDIT 4COINS 1 CREDIT 2 COINS _3 CREDITS 2COINS 1 CREDIT 4COINS 2CREDITS 5COINS 3 CREDITS 6 COINS _4 CREDITS eas PST 4 COINS _3 CREDITS 1COIN 1CREDIT 2COINS 2CREDITS | OFF | OFF] ON | ON 3COINS 3 CREDITS 4COINS 4 CREDITS
- COINS 6 CREDITS
ON | OFF} ON | ON 3 COINS 3 CREDITS 4 COINS _5 CREDITS
2 COINS _3 CREDITS [ rreepay [ON | oN| onfon| | [| |_| 1COIN 1CREDIT 2COINS 2 CREDITS
IGAME OPTION SWITCH SETTING:
OPTION 1 CREDIT TO START. 2 CREDITS TO START
ADVERTISE OFF
ee oe ee ee et 56 PIN EDGE CONNECTOR ane nor warns IAS le ZRANGA
ALIEN STORM PCB - SYSTEM 18
3P SERVICE
GND GND «s! [GN (COIN) [GSD (CONT) [GND
GND POWER
+12 volts SUPPLY
+5 volts ASSY