Club Kart STD
Club Kart (SEGA, 2001) · Manual · 114 pages · 121 sections · original scan
1ST PRINTING MAY 01 S
= ~
Standard Version
Owner’s Manual
MANUAL NO. 999-1282
Warranty
Your new Sega Product is covered for a period of 90 days from the date of shipment. This certifies that the Printed Circuit Boards, Power Supplies and Monitor are to be free of defects in workmanship or materials under normal operating conditions. This also certifies that all Interactive Control Assemblies are to be free from defects in workmanship and materials under normal operating conditions. No other product in this machine is hereby covered.
Sellers sole liability in the event a warranted part described above fails shall be, at its option, to replace or repair the defective part during the warranty period. For Warranty claims, contact your Sega Distributor.
Should the Seller determine, by inspection that the product was caused by Accident, Misuse, Neglect, Alteration, Improper Repair, Installation or Testing, the warranty offered will be null and void.
Under no circumstances is the Seller responsible for any loss of profits, loss of use, or other damages.
This shall be the exclusive written Warranty of the original purchaser expressed in lieu of all other warranties expressed or implied. Under no circumstance shall it extend beyond the period of time listed above.
BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWING: To maintain the safety:
To ensure the safe usage of the product, be sure to read the following before using the product. The following instructions are intended for the users, operators and the personnel in charge of the operation of the product. After carefully reading and sufficiently understanding the warning displays and cautions, handle the product appropriately. Be sure to keep this manual nearby the product or elsewhere convenient for referring to it when necessary.
Herein, explanations which require special attention are enclosed with dual lines. Depending on the potentially hazardous degrees, the terms of WARNING, CAUTION, etc. are used. Be sure to understand the contents of the displays before reading the text.
Indicates that mishandling the Indicates that mishandling the product product by disregarding this by disregarding this caution will cause
For the sage usage of the product, the following pictographs are used:
Indicates “HANDLE WITH CARE.” In order to protect the human body an equipment, this display is attached to places where the Owner’s Manual and or Service Manual should be referred to.
© Perform work in accordance with the instructions herein stated. Instructions for work are explained by paying attention to the aspect of accident prevention. Failing to perform work as per the instructions can cause accidents. In the case where only those who have technical expertise should perform the work to avoid hazardous situation, the instructions herein state that the serviceman should perform such work.
© Be sure to turn off power before working on the machine. To prevent electric shock, be sure to turn off power before starting the work in which the worker touches the interior of the product. If the work is to be performed in the power-on status, the Instruction Manual herein always states to that effect.
O Besure to ground the Earth Terminal (this, however, is not required in the case where a power cord with earth is used). This product is equipped with the Earth Terminal. When installing the product, Connect the Earth Terminal to the “accurately grounded indoor earth terminal” by using an earth wire. Unless the product is grounded appropriately, the user can be subject to electric shock. After performing repair, etc. for the Control equipment, ensure that the Earth Wire is firmly connected to the Control equipment.
© Ensure that the Power Supply used is equipped with an Earth Leakage Breaker. This product does not incorporate the Earth Leakage Breaker. Using a power supply which is not equipped with the Earth Leakage Breaker can cause a fire when earth leakage occurs.
© Be sure to use fuses which meet the specified rating. (only for the machines which use fuses). Using fuses exceeding the specified rating can cause a fire and electric shock.
© | Specification changes (removal of equipment, conversion and addition) not designated by SEGA are not allowed. The parts of the product include warning labels for safety, covers for personal protection, etc. It is very hazardous to operate the product by removing parts and or modifying the circuits. Should doors, lids and protective parts be damaged or lost, refrain from operating the product, and contact where the product was purchased from or the office herein stated. SEGA shall not be held responsible for any accidents, compensation for damage to a third party, resulting from the specifications not designated by SEGA. ©. Ensure that the product meets the requirements of appropriate Electrical Specifications. Before installing the product, check for Electrical Specifications. SEGA products have a nameplate on which Electrical Specifications are described. Ensure that the product is compatible with the power supply voltage and frequency requirements of the location. Using any Electrical Specifications different from the designated Specifications can cause a fire and electric shock. © _ Install and operate the product in places where appropriate lighting is available, allowing warning labels to be clearly read. To ensure safety for the customers, labels and printed instructions describing potentially hazardous situation are applied to places where accidents can be caused. Ensure that where the product is operated has sufficient lighting allowing the warnings to be read. If any label is peeled off, apply it again immediately. Please place an order with where the product was purchased from or the office herein stated. © When handling the Monitor, be very careful. (Applies only to the product w/monitor.) Some of the monitor (TV) parts are subject to high tension voltage. Even after running off power, some portions are still subject to high tension voltage sometimes. Monitor repair and replacement should be performed only be those technical personnel who have knowledge of electricity and technical expertise. © Besure to adjust the monitor (projector) properly. (Applies only to the product w/monitor.) Do not operate the product leaving on-screen flickering or blurring as it is. Using the product with the monitor not properly adjusted may cause dizziness or a headache to an operator, a player, or the customers. © _ When transporting or reselling this product, be sure to attach this manual to the product. In the case where commercially available monitors and printers are used in this product, only the contents relating to this product are explained herein. Some commercially available equipment has functions and reactions not stated in this manual. Read this manual together with the specific Instruction Manual of such equipment.
- Descriptions herein contained may be subject to improvement changes without notice. ¢ The contents described herein are fully prepared with due care. However, should any question arise or errors be found, please contact SEGA.
INSPECTIONS IMMEDIATELY AFTER TRANSPORTING THE PRODUCT TO THE LOCATION.
Normally, at the time of shipment, SEGA products are in a status allowing for usage immediately after transporting to the location. Nevertheless, an irregular situation may occur during transportation. Before turning on power, check the following points to ensure that the product has been transported in a satisfactory status. Are there any dented portions or defects (cuts, etc.) on the external surfaces of the cabinet? Are Casters and Adjusters, damaged? Do the power supply voltage and frequency requirements meet with those of the location? Are all wiring connectors correctly and securely connected? Unless connected in the correct direction, connector connections can not be made accurately. Do not insert connectors forcibly. Do power cords have cuts and dents? Do the fuses used meet specified rating? Is the Circuit Protector in an energized status? Are all accessories available? Can all Doors and Lids be opened with the Accessory keys? Can Doors and Lids be firmly closed?
TABLE OF CONTENTS
BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWING: TABLE OF CONTENTS
INTRODUCTION OF THE OWNER’S MANUAL HANDLING PRECAUTIONS ... PRECAUTIONS CONCERNING INSTALLATION LOCATION
OPERATION
ACCESSORIES ASSEMBLING AND INSTALLATION ..
- PRECAUTIONS TO BE HEEDED WHEN MOVING THE MACHINE
CONTENTS OF GAME
- EXPLANATION OF TEST AND DATA DISPLAY
8-1 SWITCH UNIT AND COIN METER
8-2 SYSTEM TEST MODE
8-3 GAME TEST MODE
- CONTROL PANEL .
9-1 ADJUSTING/REPLACING THE V.R.
9-2 GREASING
- ACCELERATOR & BRAKE
10 - 1 ADJUSTING AND REPLACING THE V.R.
10 -2 GREASING.....
- COIN SELECTOR
- REPLACING THE FLOURESCENT LAMP, AND LAMPS .
- PERIODIC INSPECTION TABLE
- TROUBLESHOOTING ....
- GAME BOARD 15 - 1 REMOVING THE GAME BOARD
- COMMUNICATION PLAY .....
16-1 INSTALLATION PRECAUTIONS
16-2 SETTING FOR COMMUNICATION PLAY 16-3 CAUTIONS TO BE HEEDED DURING COMMUNICATION PLAY
- DESIGN RELATED PARTS
- PARTS LIST
- WIRE COLOR CODE TABLE
- WIRING DIAGRAM VE 2 Sa
106 - 109
INTRODUCTION OF THE OWNERS MANUAL
This Owner's Manual is intended to provide detailed descriptions together with all the necessary information covering the general operation of electronic assemblies, electromechanicals, servicing control, spare parts, etc. as regards the product, CLUB KART STD TYPE. This manual is intended for the owners, personnel and managers in charge of operation of the product. Operate the product after carefully reading and sufficiently understanding the instructions. If the product fails to function satisfactorily, nontechnical personnel should under no circumstances touch the internal system. Please contact where the product was purchased from.
Use of this product is unlikely to cause physical injuries or damages to property. However, where special attention is required this is indicated by a thick line, the word "IMPORTANT" and its sign in this manual.
Indicates that mishandling the product by disregarding this display can cause the product's intrinsic performance not to be obtained, resulting in malfunctioning.
MPORTANT
SEGA ENTERPRISES, INC. (U.S.A.)/CUSTOMER SERVICE 45133 Industrial Drive, Fremont, California 94538, U.S.A. Phone : (415) 701-6580 Fax : (415) 701-6594
DEFINITION OF LOCATION MAINTENANCE MAN AND SERVICEMAN
Ensure that parts replacement, servicing & inspections, and troubleshooting are performed by the location's maintenance man or the serviceman. It is instructed herein that particularly hazardous work should be performed by the serviceman who has technical expertise and knowledge.
The location's maintenance man and serviceman are herein defined as follows:
"Location's Maintenance Man" : Those who have experience in the maintenance of amusement equipment and vending machines, etc., and also participate in the servicing and control of the equipment through such routine work as equipment assembly and installation, servicing and inspections, replacement of units and consumables, etc. within the Amusement Facilities and or locations under the management of the Owner and Owner's Operators of the product.
Activities of Location's Maintenance Man : Assembly & installation, servicing & inspections, and replacement of units & consumables as regards amusement equipment, vending machines, etc.
Serviceman : Those who participate in the designing, manufacturing, inspections and maintenance service of the equipment at an amusement equipment manufacturer. Those who have technical expertise equivalent to that of technical high school graduates as regards electricity, electronics and or mechanical engineering, and daily take part in the servicing & control and repair of amusement equipment.
Serviceman's Activities : Assembly & installation and repair & adjustments of electrical, electronic and mechanical parts of amusement equipment and vending machines.
LISTED
5K92 ®
AMUSEMENT MACHINE
- HANDLING PRECAUTIONS
When installing or inspecting the machine, be very careful of the following points and pay attention to ensure that the player can enjoy the game safely. Non-compliance with the following points or inappropriate handling running counter to the cautionary matters herein stated can cause personal injury or damage to the machine.
without turning power off can cause an electric shock or short circuit. In the case work should be performed in the status of power on, this manual always
To avoid causing a fire or electric shock, do not put things on or damage
Power Cords. When or after installing the product, do not unnecessarily pull the power cord. f damaged, the power cord can cause a fire or electric shock. n case the power cord is damaged, ask for replacement through where the product was purchased from or the office herein stated. Using the cord as is damaged can cause fire, electric shock or leakage. Be sure to perform grounding appropriately. Inappropriate grounding can
f) @ Before performing work, be sure to turn power off. Performing the work
cause an electric shock. Be sure to use fuses meeting specified rating. Using fuses exceeding the specified rating can cause a fire or electric shock. Completely make connector connections for IC BD and others. Insufficient insertion can cause an electric shock. Specification changes, removal of equipment, conversion and/or addition, not designated by SEGA are not permitted.
Failure to observe this may cause a fire or an electric shock. Non-compliance
with this instruction can have a bad influence upon physical conditions of the players or the lookers-on, or result in injury during play. SEGA shall not be held responsible for damage, compensation for damage to a third party, caused by specification changes not designated by SEGA. Be sure to perform periodic maintenance inspections herein stated.
S For the IC board circuit inspections, only the logic tester is allowed. The use of a multiple-purpose tester is not permitted, so be careful in this regard.
- PRECAUTIONS CONCERNING INSTALLATION
LOCATION
avoid installing in places mentioned below so as not to cause a fire, electric shock, ( This product is an indoor game machine. Do not install it outside. Even indoors, injury and or malfunctioning. @ Places subject to rain or water leakage, or places subject to high humidity in the proximity of an indoor swimming pool and or shower, etc. Places subject to direct sunlight, or places subject to high temperatures in the proximity of heating units, etc. Places filled with inflammable gas or vicinity of highly inflammable/volatile chemicals or hazardous matter. Dusty places. Sloped surfaces. Places subject to any type of violent impact. Vicinity of anti-disaster facilities such as fire exits and fire extinguishers. The operating (ambient) temperature range is from 5 C° to 40 C°. Only in the case a projector is employed, the temperature range is from 5 C° to 30.C°.
LIMITATIONS OF USAGE REQUIREMENTS
Be sure to check the Electrical Specifications. Ensure that this product is compatible with the location's power supply, voltage and frequency requirements. A plate describing Electrical Specifications is attached to the product. Non-compliance with the Electrical Specifications can cause a fire and electric shock. This product requires the Breaker and Earth Mechanisms as part of the
location facilities. Using them in a manner not independent can cause a fire
and electric shock. Ensure that the indoor wiring for the power supply is rated at 15A or higher (AC single phase 100 ~ 120V area), and 7A or higher (AC 220 ~ 240V area). Non-compliance with the Electrical Specifications can cause a fire and electric shock. Be sure to independently use the power supply equipped with the Earth Leakage Breaker. Using a power supply without the Earth Leakage Breaker can cause an outbreak of fire when earth leakage occurs. Putting many loads on one electrical outlet can cause generation of heat and a fire resulting from overload. When using an extension cord, ensure that the cord is rated at 15A or higher (AC 100 ~ 120V area) and 7A or higher (AC 220 ~ 240V area). Using a cord rated lower than the specified rating can cause a fire and electric shock.
OPERATION AREA
2.8m (D). In order to prevent injury resulting from the falling down accident during game play, be sure to secure the minimum area for operation. Be sure to provide sufficient space so as to allow this product's ventilation fan
to function efficiently. To avoid machine malfunctioning and a fire, do not
place any obstacles near the ventilation opening.
f) For the operation of this machine, secure a minimum area of 2.0m (W) X
SEGA shall not be held responsible for damage, compensation for damage to a third party, resulting from the failure to observe this instruction.
S For transporting the machine into the location's building, the minimum necessary dimensions of the opening (of doors, etc.) are 1.4m(W) and 1.7m(H).
- OPERATION
PRECAUTIONS TO BE HEEDED BEFORE STARTING THE OPERATION To avoid injury and trouble, be sure to constantly give careful attention to the behavior and manner of the visitors and players.
A In order to avoid accidents, check the following before starting the operation: @ To ensure maximum safety for the players and the customers, ensure that
Ensure that all of the Adjusters are in contact with the floor.
product can cause a falling down accident or parts damage.
A Do not put any heavy item on this product. Placing any heavy item on the
A
PRECAUTIONS TO BE HEEDED DURING OPERATION (PAYING ATTENTION TO CUSTOMERS)
A
A
@ To avoid injury and accidents, those who fall under the following categories are not allowed to play the game. Those who need assistance such as the use of an apparatus when walking. Those who have high blood pressure or a heart problem. Those who have experienced muscle convulsion or loss of consciousness when playing video game, etc. Those who have a trouble in the neck and or spinal cord. Intoxicated persons. Pregnant women or those who are in the likelihood of pregnancy. Persons susceptible to motion sickness. Persons whose act runs counter to the product's warning displays. A player who has never been adversely affected by light stimulus might experience dizziness or headache depending on his physical condition when playing the game. Especially, small children can be subject to those conditions. Caution guardians of small children to keep watch on their children during play. Instruct those who feel sick during play to have a medical examination. To avoid injury resulting from falling down and electric shock due to spilled drinks, instruct the player not to place heavy items or drinks on the product. To avoid electric shock and short circuit, do not allow customers to put hands and fingers or extraneous matter in the openings of the product or small openings in or around the doors. To avoid falling down and injury resulting from falling down, immediately stop the customer's leaning against or climbing on the product, etc. To avoid electric shock and short circuit, do not allow the customers to unplug the power plug without a justifiable reason.
Immediately stop such violent acts as hitting and kicking the product. Such violent acts can cause parts damage or falling down, resulting in injury due to fragments and falling down. Instruct the Player to adjust the seat before playing the game. Playing the game in a forcible posture can cause a contingent accident.
- ACCESSORIES
When transporting the machine, make sure that the following parts are supplied.
TABLE 4 ACCESSORIES
DESCRIPTION OWNERS MANUAL Part No. (Qty.) 420-6588-01 (1)
Figures If Part No. has no description, the Number has not been registered or can not be registered. Such a part may not be obtainable even if the customer desires to purchase it. Therefore, ensure that the part is in safekeeping with you. KEY MASTER KEY 220-5576 (2) (2) For opening/closing For the CASHBOX DOOR the doors
TAMPERPROOF WRENCH M8 540-0009-01 (1) TOOL
CARTON BOX 601-10642 (1) Used for transporting the Game Board. Refer to Next Page.
CONN 22 310-5051-22 (2) For communication play, refer to Section 16. The Keys are inside the Coin Chute Door at the time of shipment from the factory.
AC Cable (Power Cord) 600-7228 (1) TAIWAN 600-6695 (1) USA 600-6618 (1) OTHERS 600-6619 (1) HONG KONG Used for installation, of Section 5.
ASSY FIBER CABLE 600-6275-0500 (1) For communication play, refer to Section 16.
HOW TO USE THE CARTON BOX
@ When asking for the replacement or repair of the product's Game Board (NAOMI 2), be sure to put the Game Board together with the Shield Case in a Carton Box. Otherwise, the request is not acceptable.
SHIELD CASE BRACKETS ‘The shape depends on the type of product. "CHECK SIDE" Display
Wrap the Shield Case with the packing material and put it in the Carton Box as shown. Putting it upside down or packing otherwise in the manner not shown can damage the Game Board and parts.
- ASSEMBLING AND INSTALLATION
Ensure that connectors are accurately connected. cause electric shock hazard. Be careful so as not to damage wirings. shock and short circuit hazards.
Damage
This work should be performed by the Location's Serviceman. Performing work by non-te: Depending on the assembly ing by one person alone can cause
Incomplete connections can
wiring can cause electric
Maintenance Man or chnical personnel can cause a severe accident such as electric shock. Failing to comply with this instruction can cause a severe accident such as electric s| ‘ock to t e player during operation. Provide sufficient space so that assembling can be performed. Performing work in places with narrow space or low ceiling may cause an accident and assembly work to be difficult. To perform work safely and avoid serious accident such as the cabinet's falling down, do not perform work in places where step-like grade.
To perform work safely and securely, be sure to prepare a step which is in a secure and stable condition. Performing work without using the step can cause violent falling down accidents.
When carrying out the assembling and installation, follow the following 6-item sequence.
SECURING IN PLACE (ADJUSTER ADJUSTMENT)
2 | POWER SUPPLY CONNECTION
w TURNING POWER ON
4 | ASSEMBLING CHECK
The master key (accessories) in addition to the tools such as a Phillips type screwdriver, wrench, socket wrench and Ratchet Handle are required for the assembly work.
Phillips type screwdriver
SOCKET WRENCH,(M8 hexagon bolt) RATCHET HANDLE .
TT KEY MASTER
1 SECURING IN PLACE (ADJUSTER ADJUSTMENT)
A e sure that all of the adjusters are in contact with the floor. If they are not, the inet can move and cause an
® Transport the product to the
installation position. Be sure to provide adequate space allowing the player to get on and off. ADJUSTER
@) Have all of the Adjusters make
contact with the floor. Adjust the Adjuster's height by using a wrench so that the machine position is kept level.
@aAtier making adjustment, fasten
the Adjuster Nut upward and secure the height of Adjuster (FIG. 5. 3b). CASTER
FASTEN UPWARD.
Approx.Ssmm. \ as USTER FIG. 5.3 b ADJUSTER
2] POWER SUPPLY
Be sure to independently use the power supply socket outlet equipped with an Earth Leakage Breaker. Using a power supply without an Earth Leakage
The AC Unit is mounted on the right side of the machine. The AC Unit has Main SW, Circuit Protector, Earth Terminal and the Inlet which connects the Power Cord.
® Ensure that the Main SW is OFF.
MAIN SW
Main SW off
FIG. 5. 4a AC unit
FIG. 5.5a TURNING POWER ON
Connect the power by turning on the AC unit's main switch. Then the billboard's fluorescent light comes on. The monitor displays a system power-on message, and then an advertising screen (a plying-forhire screen) appears. At the same time the right and left speakers on the control panel output an advertise sound. The sound is inaudible, however, when you have disabled its function. Before an advertising screen appears the system automatically conducts an initialization. Do not touch the product until the system completes an initialization and the advertising screen appears. During an initialization the handle (steering wheel) turns counterclockwise and clockwise and stops at the original center position (for a straight-ahead direction). This corrects the volume value inside the control panel. Do not touch the handle or play the game before an initialization is completed (that is, the handle automatically stops at the center position). Failure to observe this may affect the handle's operability and the handle's force feedback (force feedback against crashing) during playing the game. If the handle's operability or force feedback is abnormal, disconnect and reconnect the power for initializing the system again. When you disconnect the power, the system saves the data for the credit number, ranking, and latest game's score. Assume that the credits effective for playing a game remain when you disconnect the power. In this case, when you will reconnect the power a game startup screen will appear with the start button flashing. If several machines are interconnected or networked for a communication play, the system checks the network. A network-checking screen as illustrated below appears before an advertising screen appears. Usually, checking the network takes 1 to 3 minutes. If the system detects a problem related with the network, it keeps displaying the network-checking screen or an error message.
Fluorescent lamps are always lit,
On-screen images are outputted.
MODE : MASTER SIZE XXX GaP x STATUS : XXXX CHECKING NETWORK Handle turns counterclockwise and clockwi
FIG. 5.5 b NETWORK check screen
ound is emitted.
4 ASSEMBLING CHECK
In the TEST MODE, ascertain that the assembly has been made correctly and IC BD. is satisfactory (refer to Section 8). In the test mode, perform the following test:
- MEMORY TEST
RAM TEST
ICIS IC16 ICI7S IC188 GOOD 1C22 1€23 1C248 C258 GOOD IC28 1C298 Goop Ic4l GooD 1c42 GooD IC44. IC45S 1C46 IC478. GOOD Ic91s 1¢928 GooD Ic98 GooD
OPTIONAL SOUND BOARD: 1c2 GooD
OPTIONAL COMMUNICATION BOARD: IC7 IC8 IC9 IC10 GOOD
PRESS TEST BUTTON TO EXIT
- C.R.T. TEST
C.R.T. TEST PAGE#1
RED
GREEN
BLUE
WHITE
PRESS SERVICE BUTTON TO ANOTHER PAGE PRESS TEST BUTTON TO EXIT
PAGE#2
RESS SERVICE BUTTON TO ANOTHER PAGE PRESS TEST BUTTON TO EXIT i. Selecting the RAM TEST on the system test mode menu screen causes the on-board memory to be tested automatically. The game board is satisfactory if the display beside each IC No. shows GOOD.
In the system test mode menu, selecting C.R.T. TEST allows the screen (on which the monitor is tested) to be displayed. Although the monitor adjustments have been made at the time of shipment from the factory, color deviation, etc., may occur due to the effect caused by geomagnetism, the location building's steel frames and other game machines in the periphery. By watching the test mode screen, make judgment as to whether an adjustment is needed.
- SOUND TEST
SOUND TEST
MAIN SPEAKER LEFT MAIN SPEAKER RIGH" OPTION SPEAKER LE! OPTION SPEAKER RIGHT > EXIT
SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON
- INPUT TEST
INPUT TEST
STEERING WHEEL XXX GAS PEDAL XXX BRAKE PEDAL XXX GEAR POSITION ON START BUTTON OFF VIEW CHANGE BUTTON OFF
SERVICE SWITCH OFF TEST SWITCH OFF
PRESS TEST AND SERVICE BUTTON TO EXIT
JVS TEST > DISPLAY CONFIG EXIT
NODE 1/1 SWITCH SYSTEM _ PLAYER _ PLAYER2 _ COIN SLOT1 0000 SLOT2 8000 ANALOG CH1 0000 CH2 0000 CH3 0000 CH4 0000 CHS 0000 CH6 0000 CH7 0000 CH8 0000
SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON In the system test mode, selecting SOUND TEST causes the screen (on which sound related BD and wiring connections are tested) to be displayed. Check if the sound is satisfactorily emitted from each speaker and the sound volume is appropriate.
Selecting the INPUT TEST on the game test mode menu screen causes the screen (on which each switch is tested) to be displayed. Press each switch. For the coin switch test,
insert a coin from the coin inlet with the coin chute door open. If the display beside each switch indicates "ON," the switch and wiring connections are satisfactory.
- OUTPUT TEST
Select OUTPUT TEST from the Menu screen in the Game Test Mode to cause the OUTPUT TEST screen (on which output unit such as lamps > START BUTTON and wiring connections are tested) to appear. VIEW CHANGE BUTTON Ensure that the output unit functions BASS SHAKER(FRONT satisfactorily. BASS SHAKER(FRONT+REAR)
PRESS TEST BUTTON TO EXIT
Perform the above inspections also at the time of monthly inspection.
- PRECAUTIONS TO BE HEEDED WHEN MOVING THE MACHINE
A
IMPORTANT
When moving the machine, be sure to unplug the power plug. Moving the machine with the plug as is inserted can damage the power cord and cause fire and electric shock hazards. When moving the machine on the floor, retract the Adjusters and ensure that Casters make contact with the floor. During transportation, pay careful attention so that Casters do not tread power cords and earth wires. Damaging the power cords can cause electric shock and short circuit hazards. When lifting the cabinet, be sure to hold the grip portions or bottom part. Lifting the cabinet by holding other portions can damage parts and installation portions due to the empty weight of the cabinet, and cause personal injury. When transporting the product in places with step-like differences in grade, disassemble into each unit before transporting. Lifting up the product in an attempt to cross the step-like differences in an as is assembled condition may damage the unit's joining portions and cause a personal injury resulting from damage. Do not insert the fork to places other than designated when using a Forklift to transport the machine. Failure to observe this could cause falling down and injury resulting from falling down.
Do not push the plastic made parts. Failure to observe this may damage parts and cause injury due to fragments resulting from damage. Do not use the handle or lever to move the product. Failure to observe this may cause the parts to be deformed or damaged.
When transporting the product in places with steps, disassemble into each unit before transporting. Inclining the product in an as is assembled condition or placing the cabinet in places with steps can damage the unit's joining portions. To protect surface, do not directly apply a rope to the surfaces of product. Use protective materials to the places the rope is applied to.
- CONTENTS OF GAME
The following explanations apply to the case the product is functioning satisfactorily. Should there be any moves different from the following contents, some sort of faults may have occurred. Immediately look into the cause of the fault and eliminate the cause thereof to ensure satisfactory operation.
Advertising (Plying-for-Hire) Performance
The billboard's fluorescent light is always on when the power is connected. The monitor displays the demonstration images and ranking data. The ranking data is updated every week. The lights (integrated with the two buttons on the control panel) are off. The right and left speakers on the control panel output an advertise sound. The right and left speakers on the seat backrest and the bass shaker do not output an advertise sound. You can activate or deactivate an advertise sound output function on the test mode screen.
j Fluorescent lamps are lit.
Image output on the monitor.
Coin Inlet
HOW TO PLAY
Operation of a single machine allows a Single Play. Operation of interconnected machines allows a Communication Play.
START BUTTON STEERING WHEEL
HANDLE VIEW CHANGE BUTTON
BRAKE PEDAL
GAS (ACCELLETOR) PEDAL a 6.76
[Single Play]
In this game, the players make their karts and enter the race for competing with each other. (00 you want to make your original kart ?
By achieving a good score in the Championship Race mode, you can step up from “Class Novice” (at start) to “Class B,” “Class A,” and “Class S.” When you step up to a higher class, you may get an extended course along which you can drive, or the performance of the kart with your character may vary. The goal is to win in the race in the environment that may vary in such a manner. By selecting “Practice Race,” you can select and run along the course for a series of races, if you desire.
This game allows the data to be retained through the cards system. In addition to the kart’s name, frame, cowl, suits, helmet, etc., information such as the total time, achievements in a series of races, the highest rank by class can be recorded on the “Club Kart Card” (hereafter “CARD”).
How to Play the Game --- If you play the Championship Race for the first time:
+ Throw coins into the slot. At this time, the value converted for the number of credits is displayed at
the bottom right corner of the screen. JDo you have the (club kart
When you throw into the slot the number of coins enabling operation of one play session, you go to the screen that asks whether you have a card. + In response to the inquiry, “Do you want to create a new card?” + If you answer with “NO,” or you do not insert any card after you answer with “YES,” Rental Kart is automatically selected as the type of the kart you can luse. In this case, you go to Step | (creating a new card). One more credit is required in this case.
+ If you throw a card into the slot without making
the selection, you will go to selection of the Race Mode.
Rental Kart Mode
In the Rental Kart Mode, you select and run along the desired one of four courses
Plese insert the card d you have it
The race restart from the last continui
for competition in lap time. You choose either one of two types of karts: for the novice and middle classes. You are required to make the specified number of circuits of the course within the predetermined time-out time. + Once you complete the first circuit, the remaining time of the time-out time for the first circuit is added to the time-out time for the second circuit. + When you complete the specified number of circuits of the course within the specified time, the finish takes place. When the time-out time reaches 0, Game Over takes place. An example where “YES” was selected is described in this document.
+ Create a new card. After entering the name, select the cowl, frame, and racing suite colors and the helmet design according to the instructions on the screen.
DoEnter your name. ant Ciptease select your Suit. as
. =-= ee a a Aisi) cio & VV T)KIIL IM FoR Ss TU V Wik YZ
oe boos |e
Pisin your Wierds cus kart CARD whch hat aieady arpanied a team The myxten wil recore the tomes eta Net you On a ow oare.
+ After you have entered all the information, you go to the confirmation screen and must make operations according to the instructions on the screen.
+ Select the Race Mode. You can choose either Championship Race or Practice Race. (“Communicated Race” is additionally displayed when two or more machines are interconnected.) Turn the =: _Championst ionship race steering wheel clockwise or counterclockwise Gees tov eel fou td - OOO for selection. Then, determine the selection ——
by pressing the accelerator pedal. Practice race.
Championship Race
+ In this mode, you compete with the other players for the total achievement of a Series of Races that are done, depending on four classes (Novice, B, A, and S). The race in this mode begins after you have created the feature of creating your own original kart (one of the distinctive features of this game) and the card to save the running record. With the card, you can save the data before completion of the series of races; at the next play time, you can resume the game from the ending point in the previous session of the game.
Practice Race
You can select and run along the desired one of the courses along which you run in a Series of Races. The number of courses from among which can select depends on the number of racces included in the series, which varies with the class to which you belong (4 of Novice, 6 for B, 8 for Class, and 10 for S).
+ Information about the player’s kart (class, the number fo times won and defeated, the top ranking, the best time, the number of races in the series, etc.) and the course map are displayed before the race starts. When you created a card for the first time, the player’s kart starts at the rearmost position. You are required to make the specified number of circuits of the course within the predetermined time-out time. Once you complete the first circuit, the remaining time of the time-out time for the first circuit is added to the time-out time for the second circuit.When you complete the specified number of circuits of the course within the specified time, the finish takes place. When the time-out time reaches 0, Game Over takes place. + If your kart touches the wall of the course or another kart or goes outside the course while the game is in progress, you feel a reaction through the steering wheel. + While the game is in progress, pressing the Viewpoint Change button changes the viewpoint on the screen. The button is continually flashing while the game is in progress. + While the game is in progress, pressing the Start button toggles between the map that shows the player kart’s and the time display that indicates the other karts’ positions and the best time in the class and that of your records.
+ After each race is completed, the Results Screen appears if you have run along the whole course. After the Results Screen appears, the Select Sponsor Screen may appear, depending on the results of the series of races. The number of sponsors, at random, increases or decreases, depending on the achievement. The logo of the sponsor you selected can be attended to the kart if you desire this.
When Select Sponsor Screen appears for the first ince II Z 7 77 7 _7_ 777: ma =
you assign the team name to your kart. O)Selact a Sponsor
oxo
(iEnd of Series. are listed when the predetermined number of races have been completed for each of the classes. If you have established good achieve-
ment, a screen appears that lets you select vereeay Nene imavepwite
whether to try the next series of races at the NG current or upper class.
+ Ifthe Practice Race Mode is entered or all the credits have been exhausted after the data is written onto the card after completion, Game Over takes place. If you are in the Championship Race Mode, you go to the Continue Screen. If you still have credits for one or more play sessions at this time in the Championship Race Mode, you can go to the next course and enjoy one or more play sessions after jumping to the course map display is Step ???.
[Communicated Play]
Communicated Play differs slightly from Single Play regarding the game starting procedure and how to play the game.
+ When coins you throw into the slot the coins with which you can enjoy a play session, the Entry Screen appears and, at the same time, the Start button begins to flash.
+ If you desire a competitive play, throw the appropriate number of coins into the slot at another seat. If you desire the single play mode, press the Start button immediately after the Entry Screen appears.
+ Once the Entry Screen appears, a countdown starts. If a person who desires to compete with you does not appear before the count reaches 0 (zero), you have to enjoy the game in the Single Play Mode.
+ Once the count in the Entry Screen reaches 0, you are brought to the Select Rental Kart Screen. Turn the steering wheel clockwise or counterclockwise to choose selection by pressing the accelerator pedal and Start button. If you have a card, you will be subsequently able to use your own original kart by inserting the card into the slot. The course assignments to the players are determined by majority of the players.
+ Once the course assignments are determined, information about the players’ karts (class, the number of times won and defeated, the top ranking, the best time, the number of races in the series, etc.) and the course map are displayed before the race starts.
+ In the race, the players compete with each other for their ranks. Each time the first-rank player completes one circuit of the course, the time that remained is added to that of the next circuit of the course. When you complete the specified number of circuits of the course within the specified time, the finish takes place. When the time-out time reaches 0, Game Over takes place.
+ STEERING DIR This is a setting about the cabinet. Basically, you do not need to change it. You should use the factoryadjusted setting.
+ CARD SYSTEM This sets the mode of operation for the card system unit. For usual operation, set ENABLE. If the card system unit is detached from the system, set DISABLE.
+ BONUS GAMES This sets the count of plays given as a bonus when a new card is created. By setting this, the count can be set to 0 to 3 times.
- EXPLANATION OF TEST AND DATA DISPLAY
By operating the switch unit, periodically perform the tests and data check. When installing the machine initially or collecting cash, or when the machine does not function correctly, perform checking in accordance with the explanations given in this section. The following shows tests and modes that should be utilized as applicable.
SEGA HIKARU GAME BOARD is used for the product. The system of this game board
allows another game to be played by replacing the ROM Board Case mounted on the SEGA. HIKARU CASE. As such, the Test Mode of this system consists of the System Test Mode for the system to execute SELF-TEST, COIN ASSIGNMENTS, ete. used in common for the machines employing the SEGA HIKARU BOARD, and the Game Test Mode for the specific product to execute Input/Output test for the operation equipment, difficulty setting, etc.
The contents of settings changed in the TEST mode are stored when the test
mode is finished from EXIT in the menu mode. If the power is turned off
before the TEST mode is finished, the contents of setting change become
Entering the TEST mode clears fractional number of coins less than one credit
and BONUS ADDER data. When the 2 or more machines are linked for communication play, be careful to enter the test mode. If one of the machines linked enters the test mode, all others display the NETWORK CHECK screen.
TABLE 8 EXPLANATION OF TEST MODE REFERENCE ITEMS DESCRIPTION SECTIONS
INSTALLATION | When the machine is installed, perform the following: OF MACHINE 1. Check to see that each setting is as per standard setting made at | 8-2 F,G, 8-3 F the time of shipment.
- In the INPUT TEST mode, check such input devices as each 8-2C, 8-3B SW, V.R., etc.
- In the OUTPUT TEST mode, check such output devices as 8-3.C lamps, motors, etc.
- In the SELF-TEST mode, check ICs on the IC Board. 8-2 BJ
| MEMORY | Choose MEMORY TEST in the MENU mode to allow the | 8-2 BJ |
MEMORY test to be performed. In this test, PROGRAM RAMs, ROMs, and ICs on the IC Board are checked.
PERIODIC Periodically perform the following:
| SERVICING | 1. MEMORY TEST | 8-2 BJ |
- Ascertain each setting. 8-2 F,G, 8-3 F
- In the INPUT TEST mode, test the CONTROL device 8-2 C, 8-3B
- In the OUTPUT TEST mode, check such output devices as 8-3.C lamps, motors, etc.
| CONTROL | 1. In the INPUT TEST mode, check such input devices as each | 8-2C,8-3B |
SYSTEM SW, V.R., etc.
- Adjust or replace each SW and VR. 8-3 DE,
- If the problem can not be solved yet, check the CONTROL's 9,10 moves.
| MONITOR | In the MONITOR ADJUSTMENT mode, | 8-2E |
check to see if the adjustment is appropriately made. 11
| IC BOARD | 1. MEMORY TEST | 8-2 BJ |
- In the SOUND TEST mode, check the sound related ROMs. 8-2D
| DATA CHECK | Check such data as game play time and histogram to adjust the | 8-2 H, 8-3G |
difficulty level, etc.
8-1 SWITCH UNIT AND COIN METER
IMPORTANT
not specified can
Adjust to the optimum sound volume by considering the environmental requirements of the installation location. If the COIN METER and the game board are electrically disconnected, game play is not possible. A cover is provided on the bass shaker output adjustment volume in order to prevent the BASE SHAKER against being carelessly adjusted.
SWITCH UNIT
Open the coin chute door, and the switch unit shown will appear. The functioning of each SW is as follows: The sound volumes of the front and rear speakers are adjusted as indicated by the illustration on the switch unit, at the factory before shipping. This adjustment aims to attain the best output balance between the front and rear speakers. Remember that carelessly changing this adjustment may cause the best balance to be lost. COIN METER
| © SOUND VOLUME PUSH BUTTON
FIG. 8. 1 a SWITCH UNIT
TEST BUTTON : For the handling of the test button, refer to the following pages. TEST SERVICE BUTTON : Gives credits without registering on the coin meter. SERVICE SOUND VOLUME : Adjusts the sound volume of the left and right speakers on the control panel. FRONT SPEAKER SOUND VOLUME : Adjusts the sound volume of the left and right speakers on the seat backrest. REAR SPEAKER BASE SHAKER Output Adjustment Volume —: Adjusts the vibration output of the base shakers each on BASS SHEAKER the seat backrest and the control panel.
COIN METER
Open the Cashbox Door by using the key to have the Coin Meter appear underneath the Cashbox. COIN METER, ‘© ©)
FIG. 8. 1 b COIN METER
8-2 SYSTEM TEST MODE
The contents of setting changes in SYSTEM ASSIGNMENTS, COIN ASSIGNMENTS, and GAME TEST MODE are stored when the test mode is EXITed. Ifthe power is turned off before EXITing, the contents of setting
This test mode mainly allows the IC Board to be checked for accurate functioning, monitor color to be adjusted as well as COIN ASSIGNMENTS and GAME ASSIGNMENTS to be adjusted.
TEST ITEM SELECT
@) After turning power on, press the TEST button to have the following test item menu displayed.
SYSTEM MENU
RAM TEST JVS TEST SOUND TEST C.R.T. TEST SYSTEM ASSIGNMENTS COIN ASSIGNMENTS BOOKKEEPING BACKUP DATA CLEAR CLOCK SETTING
ROM BOARD TEST GAME TEST MODE [XXXXXXXXXXXXXXX]
-> EXIT
SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON
@ Press the SERVICE button to move the arrow. Bring the arrow to the desired item and press the TEST button.
® Upon finishing the test, bring the arrow to EXIT and press the TEST button to return to the Game mode.
A. RAM TEST
This allows for checking the functioning of the RAM on the NAOMI 2 Main BD. "GOOD" is displayed for satisfactory RAMs, and "BAD" is indicated for irregular RAMs, if any.
RAM TEST
TESTING NOW
1C29 GOOD 1C35 GOOD IC0O9 GOOD IC10 GOOD IC11 GOOD IC12 GOOD IC16 GOOD IC18 GOOD 1C20 GOOD IC22 GOOD IC17 GOOD IC19 GOOD IC21 GOOD 1C23 GOOD 1C106 GOOD 1IC107 GOOD IC108 GOOD 1IC109 GOOD IC111 GOOD 1C113 GOOD IC115 GOOD 1IC117 GOOD 1C112 GOOD IC114 GOOD 1C116 GOOD IC118 GOOD
PRESS TEST BUTTON TO EXIT
"TESTING NOW" shows up (flashing) on the screen during the test. Returns to the menu screen when the TEST button is pressed after the test is over.
B. JVS TEST
In this test, Specifications of the I/O Board connected to NAOMI 2 can be checked, and INPUT TEST can be performed. First, I/O Board Specifications are displayed.
JVS TEST INPUT TEST NEXT NODE -> EXIT NODE V/1 NAME SEGA ENTERPRISES,LTD. VO BD JVS 837-13551 Ver 1.00 CMD VER 1.1 JVS VER 2.0 COM VER 1.0 SWITCH 2PLAYER(S) 13BITS COIN 2SLOT ANALOG 8CH ROTARY OCH KEYCODE 0 SCREEN X:0 Y:0 CH:0 CARD OSLOT HOPPER OUT 0CH DRIVER OUT 6SLOT ANALOG OUT 0CH CHARACTER CHARA:0 LINE:0 BACKUP 0
SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON (A) (B) ©)
i Name and version of /O BOARD.
Select with the SERVICE button and press the TEST button. (A) (B)
Co) INPUT TEST NEXT NODE the next I/O Board.
EXIT
INPUT TEST SCREEN Proceeds to the INPUT TEST of I/O BOARD being displayed. In the case where more than 2 I/O Boards are connected, proceeds to
Returns to the menu mode.
JVS TEST INPUT TEST NEXT NODE -> EXIT
NODE 1/1
SWITC! SYSTEM PLAYERI 00000000 00000000 00000000 00000000 PLAYER2
COIN 00000000 1 j= When INPUT is performed for the switches of Control Panel, etc., the value changes to 1 from 0.
0000 0000 ANALOG—W_, 0000 0000 0000 0000 0000 0000 0000 0000 p> If the Coin SW is inputted, the count starts. When the TEST MODE is finished, the count is cleared and returned to[0000].
SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON pe Analogue values are displayed between 0000 and FFOO.
C. SOUND TEST
Sound Output test can be performed. Beep sounds can be emitted from each of left/right Speakers.
SOUND TEST
RIGHT SPEAKER OFF — Enmitted from the right-hand side Speaker. LEFT SPEAKER OFF — Emitted from the left-hand side Speaker. -> EXIT — Returns to the menu mode.
SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON
D. C.R.T. TEST
- RGB COLOR ADJUSTMENT SCREEN In this page, monitor color can be checked.
C.R.T. TEST 1/2 Each of red, green, and blue is the darkest at the 1 32 leftmost end, and becomes brighter towards the right-hand end in 31 gradations. Monitor RED brightness is satisfactory if the white color bar GREEN is black at the left end and if it is white at the right end. BLUE Press the TEST button to proceed to the next WHITE page.
PRESS TEST BUTTON TO CONTINUE
- MONITOR SIZE ADJUSTMENT SCREEN In this page, monitor size can be checked.
C.R.T. TEST 2/2 Adjust so that the checkered patterns do not go beyond the screen. Press the TEST button to return to the menu mode.
RESS TEST BUTTON TO EXIT
E. SYSTEM ASSIGNMENTS
The settings of cabinet and board can be changed. Game related assignments such as game difficulty, etc. are performed in K. GAME TEST MODE.
® Press the SERVICE button to move the arrow. Bring the arrow to the desired item.
@ Press the TEST button to change the setting.
® Upon finishing the setting, move the arrow to EXIT and press the TEST button.
SYSTEM ASSIGNMENTS,
| CABINET TYPE | 1PLAYER(S) | (A) |
ADVERTISE SOUND ON (B)
| MONITOR TYPE | HORIZONTAL] | (C) |
| SERVICE TYPE | COMMON | (D) |
-> EXIT
SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON
(A) CABINET TYPE (IPLAYER(S), 2PLAYER(S), 3PLAYER(S), 4PLAYER(S)) Sets the number of players between | and 4. Fix setting to 1 PLAYER(S).
(B) ADVERTISE SOUND (ON, OFF) Sets whether ADVERTISE sound is to be emitted or not.
(C) MONITOR TYPE (HORIZONTAL, VERTICAL) Sets the on-screen display to the positional direction of monitor (HORIZONTAL/VERTICAL) Fix setting to HORIZONTAL. HORIZONTAL: Normal on-screen display
VERTICAL: On-screen display when the monitor is vertically positioned as against
normal HORIZONTAL position.
(D) SERVICE TYPE (COMMON, INDIVIDUAL) Sets the functioning of when the SERVICE button is pressed, in case that several SERVICE buttons exist. Fix setting to COMMON.
COMMON: By pressing any SERVICE button, Service credit can be obtained for all
Players. By pressing SERVICE button, Service credit can be obtained for the Player corresponding to the SERVICE button pressed. INDIVIDUAL:
F. COIN ASSIGNMENTS
In this mode, the setting of incremental credit increase as against coin insertion can be changed.
® Press the SERVICE button to move the arrow. Bring the arrow to the desired item.
@ Press the TEST button to change the setting.
@Upon finishing the setting, bring the arrow to EXIT and press the TEST button.
COIN ASSIGNMENTS
MANUAL SETTING SEQUENCE SETTING ->EXIT
SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON COIN ASSIGNMENTS
COIN CHUTE TYPE COMMON (A) COIN CHUTE TYPE INDIVIDUAL COIN/CREDIT SETTING #1 (B) COIN/CREDIT SETTING #1 COIN CHUTE #1 COIN CHUTE #1 1 COIN 1 CREDIT 1 COIN 1 CREDIT
COIN CHUTE #2 1 COIN 1 CREDIT © G MANUAL SETTING SEQUENCE SETTING ->EXIT
SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON
Setting to COMMON
(A) COIN CHUTE TYPE (COMMON, INDIVIDUAL) Fix setting to COMMON.
COMMON Setting to INDIVIDUAL
This setting is for the cabinet which has a coin chute(s) for common use by plural players. Up to 2 Coin Chutes (#1 and #2) can be used and also, (B) COIN/CREDIT SETTING ratio can be set separately for #1 and #2.
INDIVIDUAL This setting is for the cabinet in which each player uses an independent coin chute. Coins inserted by each player are handled as the player's credits. Depending on the CABINET TYPE setting in the SYSTEM ASSIGNMENTS and the functioning of the connected I/O Board, the number of Coin SW INPUT ports varies between | and 4. (B) COIN/CREDIT SETTING ratio is common for eath Coin Chute.
(B) COIN/CREDIT SETTING (#1 ~# 27) Sets the credit increase increment per coin insertion. There are 27 settings from #1 to #27, expressed in CQ © credit(s) as against © © coins inserted. #27 refers to FREE PLAY. For details, refer to Table 1 (COMMON) and Table 2 (INDIVIDUAL).
(C) MANUAL SETTING The Credit's incremental increase settings as against a coin insertion are shown in further details than in (B) above (refer to Table 3). Also, note that when this MANUAL SETTING is performed, (B) COIN CREDIT setting becomes ineffective.
MANUAL SETTING
COIN ASSIGNMENTS MANUAL SETTING
COIN TO CREDIT 1 BONUS ADDER NO BONUS ADDER COIN CHUTE #1 MULTIPLIER 1 COIN COUNT AS | COIN COIN 123456789 CREDIT 123456789
COIN CHUTE #2 MULTIPLIER 1 COIN COUNT AS 1 COIN COIN 123456789 CREDIT 123456789
SEQUENCE SETTING
->EXIT
SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON (D) (E)
(G) COIN ASSIGNMENTS MANUAL SETTING
COIN TO CREDIT 1 BONUS ADDER NO BONUS ADDER COIN CHUTE MULTIPLIER 1 COIN COUNT AS 1 COIN COIN 123456789 CREDIT 123456789
SEQUENCE SETTING
->EXIT
SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON
Setting to COMMON
(D) COIN TO CREDIT Determines COIN/CREDIT setting.
(E) BONUS ADDER Setting to INDIVIDUAL
This sets how many coins should be inserted to obtain one SERVICE COIN.
(F) COIN CHUTE ( # 1 / #2) MULTIPLIER This sets how many tokens one coin represents.
Table 1: COIN/CREDIT SETTING (COIN CHUTE COMMON TYPE)
NAME OF SETTING COIN CHUTE 1 COIN CHUTE 2
| SETTING #1 1 COIN | 1 CREDIT | 1 COIN | 1 CREDIT |
| SETTING #2 1 COIN | 2 CREDITS | 1 COIN | 1 CREDIT |
| SETTING #3 1 COIN | 3 CREDITS | 1 COIN | 1 CREDIT |
| SETTING #4 1 COIN | 4 CREDITS | 1 COIN | 1 CREDIT |
| SETTING #5 1 COIN | 5_CREDITS | 1 COIN | 1 CREDIT |
| SETTING #6 1 COIN | 2 CREDITS | 1 COIN | 2_ CREDITS |
| SETTING #7 1 COIN | 5_ CREDITS | 1 COIN | 2 CREDITS |
| SETTING #8 1 COIN | 3__CREDITS | 1 COIN | 3__ CREDITS |
| SETTING #9 1 COIN | 4 CREDITS | 1 COIN | 4 CREDITS |
| SETTING #10 1 COIN | 5_ CREDITS | 1 COIN | 5 CREDITS |
| SETTING #11 1 COIN | 6 CREDITS | 1 COIN | 6 CREDITS |
SETTING #12 2 COINS 1 CREDIT 2 COINS 1 CREDIT
| SETTING #13 1 COIN | 1 CREDIT | 2 COINS 1 CREDIT | |
| SETTING #14 1 COIN | 2_ CREDITS | 2_ COINS 1 CREDIT | |
| SETTING #15 1 COIN | 1 CREDIT | 1 COIN | 1 CREDIT |
2 COINS 3 CREDITS 2 COINS 3__ CREDITS
| SETTING #16 1 COIN | 3. CREDITS | 1 COIN | 1 CREDIT |
2_ COINS 3__ CREDITS
SETTING #17 3 COINS 1 CREDIT 3__ COINS 1 CREDIT
SETTING #18 4 COINS 1 CREDIT 4 COINS 1 CREDIT
| SETTING #19 1 COIN | 1 CREDIT | 1 COIN | 1 CREDIT |
2 COINS 2 CREDITS 2 COINS 2 CREDITS
- COINS 3. CREDITS 3. COINS 3. CREDITS
4 COINS 5_ CREDITS 4 COINS 5 CREDITS
| SETTING #20 1 COIN | 5 CREDITS | 1 COIN | 1 CREDIT |
2 COINS 2 CREDITS
3 COINS 3. CREDITS
4 COINS 5 CREDITS
SETTING #21 5 COINS 1 CREDIT 5 COINS 1 CREDIT
| SETTING #22 1 COIN | 2 CREDITS | 3. COINS 1 CREDIT |
5 COINS 2 CREDITS
SETTING #23 2 COINS 1 CREDIT 2 COINS 1 CREDIT
4 COINS 2 CREDITS 4 COINS 2 CREDITS
5 COINS 3 CREDITS 5 COINS 3__ CREDITS
| SETTING #24 1 COIN | 3. CREDITS | 2 COINS 1 CREDIT |
4 COINS 2 CREDITS
5 COINS 3 CREDITS
| SETTING #25 1 COIN | 1 CREDIT | 1 COIN | 1 CREDIT |
2 COINS 2 CREDITS 2 COINS 2 CREDITS
3 COINS 3. CREDITS 3. COINS 3. CREDITS
4 COINS 4 CREDITS 4 COINS 4 CREDITS
5 COINS 6 CREDITS 5 COINS 6 CREDITS
| SETTING #26 1 COIN | 6 CREDITS | 1 COIN | 1 CREDIT |
2 COINS 2 CREDITS
- COINS 3 CREDITS
4 COINS 4 CREDITS
5 COINS 6 CREDITS
SETTING #27 FREE PLAY FREE PLAY
Table 2: COIN/CREDIT SETTING (COIN CHUTE INDIVIDUAL TYPE) NAME OF SETTING] EACH SEAT’S COIN CHUTE | NAME OF SETTING] EACH SEAT'S COIN CHUTE
| SETTING #1 | TCOIN | _1 CREDIT | SETTING #21_| | 5 COINS | 1 CREDIT |
| SETTING #2 | 1COIN | 2 CREDITS | SETTING #23 | | 2COINS | 1 CREDIT |
| SETTING #3 | 1COIN | 3 CREDITS | 4 COINS | 2 CREDITS | |
| SETTING #4 | 1 COIN | 4 CREDITS | SCOINS | 3 CREDITS | |
| SETTING #5 | 1COIN | _5 CREDITS | SETTING #25 | | 1COIN | 1 CREDIT |
| SETTING#I1_| | 1COIN | _6CREDITS | 2COINS | 2 CREDITS | |
| SETTING #12_| | 2 COINS | 1 CREDIT | 3 COINS | 3 CREDITS | |
| SETTING #15 | | 1COIN | 1 CREDIT | 4COINS | 4 CREDITS | |
| 2 COINS | 3 CREDITS | SCOINS | 6 CREDITS | ||
| SETTING #17_| | 3 COINS | 1 CREDIT | SETTING #27_| | FREE PLAY |
SETTING #18 | 4COINS 1 CREDIT SETTING #19 | 1COIN 1 CREDIT 2COINS 2 CREDITS
3 COINS 3 CREDITS 4 COINS _5 CREDITS
Table 3: MANUAL SETTING
| COIN TO CREDIT | 1 | COIN | 1 | CREDIT |
| 2 | COINS | 1 | CREDIT | |
| 3. | COINS | | | CREDIT | |
| 4 | COINS | 1 | CREDIT | |
| 5 | COINS | 1 | CREDIT | |
| 6 | COINS | 1 | CREDIT | |
| 7_COINS | 1 | CREDIT | ||
| 8 | COINS | 1 | CREDIT | |
| 9 | COINS | 1 | CREDIT |
BONUS ADDER NO BONUS ADDER COINS GIVE EXTRA COIN COINS GIVE EXTRA COIN COINS GIVE EXTRA COIN COINS GIVE EXTRA COIN COINS GIVE EXTRA COIN COINS GIVE EXTRA COIN COINS GIVE EXTRA COIN ©]}oo]ra}la}ufa}oo}r COINS GIVE EXTRA COIN
COIN CHUTE (#1/#2) MULTIPLIER COIN COUNTS AS COIN COIN COUNTS AS COINS COIN COUNTS AS COINS COIN COUNTS AS COINS COIN COUNTS AS COINS COIN COUNTS AS COINS COIN COUNTS AS COINS COIN COUNTS AS COINS COIN COUNTS AS C}olralatufA}ofrml— COINS
(G) SEQUENCE SETTING Number of credits required for starting game, etc. can be set. Function varies depending on the specific games. To find out what kind of functions are allotted to each sequence, or what is the initial value for each sequence, refer to the Instruction Manual of the game connected. Each sequence can be set between | ~ 5 credit(s).
COIN ASSIGNMENTS SEQUENCE SETTING
SEQUENCE 1 1 CREDIT(S) SEQUENCE 2 1 CREDIT(S) SEQUENCE 3 1 CREDIT(S) SEQUENCE 4 1 CREDIT(S) SEQUENCE 5 1 CREDIT(S) SEQUENCE 6 1 CREDIT(S) SEQUENCE 7 1 CREDIT(S) SEQUENCE 8 1 CREDIT(S) -> EXIT [WILD RIDERS XXXXXXXXXX] DESCRIPTION OF SEQUENCE 1 CREDIT TO START 2 NO USE 3 NO USE 4 NO USE 5 NO USE 6 NO USE 7 NO USE 8 NO USE
SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON
In cases of video games such as WILD RIDERS. : SEQUENCE | : Number of credits required for game start (initial value=1) SEQUENCE 2~8: NOT USED.
G. BOOKKEEPING
+ BOOKKEEPING 1/2 This allows such data as operating time/No. of coins inserted/ No. of credits to be checked.
BOOKKEEPING 1/2
TOTAL TIME OD 00H 00M 00S
CREDIT °
COIN 1 COIN 2 COIN 3 COIN 4 ocooo
TOTAL COIN 0 COIN CREDIT 0 SERVICE CREDIT 0 TOTAL CREDIT 0
PRESS TEST BUTTON TO CONTINUE
Press the TEST button to proceed to BOOKKEEPING 2/2.
- BOOKKEEPING 2/2 Each sequence displays the frequency of functioning.
BOOKKEEPING 2/2
PLSEQI 0 P1SEQ2 0 P1SEQ3 0 P1SEQ4 0 PISEQS 0 PLSEQ6 0 P1SEQ7 0 PISEQ8 0
PRESS TEST BUTTON TO EXIT
In cases of video games such as WILD RIDERS. : PISEQ1: Play frequency of Player | PI SEQ2~8: NOT USED.
H. BACKUP DATA CLEAR
Clears the contents of BOOKKEEPING.
BACKUP DATA CLEAR
YES(CLEAR) -> NO(CANCEL)
SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON
When clearing, bring the arrow to YES by using the SERVICE button and press the TEST button. Bring the arrow to NO and press the TEST button to have the menu mode return without clearing the data. COMPLETED is displayed when clearing is completed. Press the TEST button to return to the menu mode.
I. CLOCK SETTING
Set YEAR, MONTH, DAY, HOUR, and MINUTE for NAOMI 2 Main BD.
CLOCK SETTING
1998 12/02 14:30 33 WED
YEAR MONTH DAY HOUR MINUTE -> EXIT
SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON
Select the desired item with the SERVICE button and press the TEST button to increase the value. Upon finishing the SETTING, bring the arrow to EXIT and press the TEST button to return to the menu mode.
J. ROM BOARD TEST
In this test, on-ROM-BD ROM check is executed. If GOOD is displayed below RESULT, it is satisfactory. BYTE and WORD refers to the check sum of each unit.
GAME ROM TEST [XXXXXXXXXXXXX]
NO. TYPE RESULT BYTE WORD 1C22 16M _ ---- 0123 4567 IC1 64M GOOD 0123 4567 IC2 64M GOOD 0123 4567 IC3 64M GOOD 0123 4567 IC4 64M GOOD 0123 4567 IC5 64M GOOD 0123 4567 IC6 64M GOOD 0123 4567 IC7 64M GOOD 0123 4567 IC8 64M GOOD 0123 4567 IC9 64M GOOD 0123 4567 IC1064M GOOD 0123 4567
1C20 64M GOOD 0123 4567
PRESS TEST BUTTON TO EXIT
Program ROMs (IC22) do not display GOOD or BAD. Press the TEST button to return to the menu mode.
K. GAME TEST MODE
Enters the TEST mode of the game connected. The TEST mode includes INPUT test, GAME ASSIGNMENTS such as game difficulty and others, BOOKKEEPING, etc. Depending on specific games, necessary items are added and unnecessary items removed. As such, the contents thereof may be changed.
8-3 GAME TEST MODE
A. SETTING THE CARD
S
The card reader/writer is located on the top of the coin chute tower. Place the cards on the card reader/writer.
+ Unlock and open the cover to find the card reader/writer. The dispenser on which you should place the cards is located at the rear of the reader/writer.
+ From the car reader/writer, take out the dispenser upward in a straight line.
+ Remove the cover from the back of the dispenser.
+ Place the cards into the dispenser according to the instructions on the sticker annexed to the dispenser. There is no print face on a card of the Club Kart. Determine the card in reference to the inserting direction mark located at corners of the cards. Do not confuse the top/bottom or direction.
+ Reinstall the cover to the dispenser.
+ Insert the dispenser into the card reader/writer. The dispenser can be inserted only in the predetermined orientation.
+ Close and lock the cover.
B. TURNING ON THE POWER
Turn on th AC unit’s main switch to supply power to the unit. Once power is turned on, the flourescent lamp in the bill board lights up. The Start System Screen displays after a lapse of several seconds. It is followed by the screen that indicates that the network is currently being checked if the communication mode has been set. If there is a bad or improper communication connection, each screen will not proceed to the next, remaining on the currently network-checked sreen. If this occurs, resolve the error according to the instructions in this document. If the communication mode has not been set or the communication check ends normally, the Motor Check Screen returns. While the Motor Check Screen is on-screen, the steering wheel can move either clockwise or counterclockwise. If you touch the wheel, the motor check is hindered and the game will not operate normally. So, you must not touch it at this time. Failures are displayed, if found. Resolve the errors according to the instructions in this document. Pressing the Start button while a failure is on-screen allows you to go to the next screen and start the game without reaction. Next the Check Card Reader/Writer Screen displays. If cleaning is required or a failure is found, this is indicated on the screen. In this case, resolve the error according to the instructions in this document. Once all the above steps have been completed, the Advertise Screen displays and voices are output through the left and right loudspeakers, unless you have set the machine so that no voices are output during the Advertise mode. This product retains the number of credits and the ranking data even after the power is turned off. It does not retain data about the fractional number of coins (i.e., the number of coins not reaching one credit) or the bonus adder count.
C. CARD READER/WRITER.
Take care if you work with the machine, without turning the power, in an attempt to return to the game. In the alive state, the machine may operate suddenly, causing your finger to
If a trouble such as card jamming occurs on the card reader/writer, you are notified of the trouble on the screen. You cannot proceed to a play unless you resolve the trouble at this time. First identify the trouble before you begin to take action. When all cards are used up, you can no longer issue a new card, with the message “Now new Club Kart Card” cannot be created” on-screen, instead of a trouble indication.
To obtain the dedicated or cleaning cards, place an order to the contact point or the dealer from which you purchased the product. In the order form, write down the card name and the amount of cards. With each of the following part numbers, you can purchase 200 dedicated and 30 cleaning cards. Dedicated Card Part number: 601-11051 Name: CARD PACKAGE CKT Cleaning Card Part number: 601-11050 Name: CLEANING KIT
- Action in Operation
The game board of this product backs up the data only when the card reader/writer detects a trouble DURING OPERATION and the Error Screen displays. However, no written data is backed up in the following cases:
+ An action deemed to be illegal was detected while the game or write was in operation.
If backed up data remains when the power is turned on, the Check Card Reader/Writer Screen will be replaced with the Save Data screen. The backed up data is cleared in the following cases:
+ After an action was taken against a trouble, normal write ended. + The backed up data was cleared in the Game Test Mode. + Data save taking place at power-on time was canceled, and the succeeding game ended.
If the card reader/writer has not been set as being unused, you will be unable to select any game mode with use of cards while the game will be in progres Thus, for the card reader/writer, deal with the player, paying attention to the following points:
+ When a trouble occurs during write operation, the retained data can be written for proceeding to the game by resolving the trouble without turning on the power. If you resolved the trouble with power off, write the data according to the instructions on the screen when you attempt to turn on the power.
+ Even if the player request the system for use of cards when you have set the machine so that the card reader/writer is not used, the request is rejected because of the nature of the system.
- Setting the Card
The card reader/writer is located on the top of the coin chute tower. Place the cards on the card reader/writer. Card setting is enabled with power either on or off.
+ Unlock and open the cover to find the card reader/writer. The dispenser on which you should place the cards is located at the rear of the reader/writer. + From the card reader/writer, take out the dispenser upward in a straight line. + Remove the cover from the back of the dispenser. + Place the cards into the dispenser according to the instructions on the sticker annexed to the dispenser. There is no print face on a card of the Club Kart. Determine the card in reference to the inserting direction mark located at corners of the cards. Do not confuse the top/bottom or direction. + Reinstall the cover to the dispenser. + Insert the dispenser into the card reader/writer. The dispenser can be inserted only in the predetermined orientation. + Close and lock the cover.
- Head Cleaning
This product memorizes the count you use the card reader/writer. When the power is turned off and on after the count of use exceeds 100, the head cleaning mode is entered while the Check Card Reader/Writer Screen is on-screen after you turn on the power. At this time, using a dedicated cleaning card, use the cleaning card procedure according to the instructions on the screen. The head cleaning mode cannot be quitted for being ready for starting the game unless the head cleaning is completed. You can use the Test Mode to perform the head cleaning mechanism assembly. For details, see the “Test Mode” section in this document.
Start the cleaning clears the count of use above.
+ Insert the cleaning card into the slot according to the instructions on the screen. The card is retracted automatically.
+ Ascreen displays that shows that cleaning is in progress.
+ Once the cleaning is completed, the cleaning card is ejected from the slot. Take out the cleaning card.
Cleaning Card Reader/Writer Screen
CARD R/W
CLEANING PLEASE INSERT CLEANING CARD
PRESS START TO CANCEL
Insert the cleaning card into the slot. Now cleaning. Wait for a minute. Cleaning is complete. Take out the card. You cannot proceed to the next step until you take it out.
- Takin Action Against Card Jamming
If card jamming occurs, the error is shown on the screen. Use the procedure to take action against the trouble:
+ Unlock and open the cover.
+ Unlock the hatch by drawing the green shaft attached to the top cover on the card reader/writer. While drawing the shaft, open the cover up.
+ Remove the card jammed in the card reader/writer.
+ While drawing the shaft, close the cover. With the top cover closed, release the green shaft. Check that the top cover has been locked securely.
Forcible Cleaning
This product memorizes the count you use the card reader/writer. When the power is turned off and on after the count of use exceeds 100, the head cleaning mode is entered while the Check Card Reader/Writer Screen is on-screen after you turn on the power. The head cleaning mode cannot be quitted for being ready for starting the game unless the head cleaning is completed. When the card reader/writer is subjected to head cleaning, the count of use is cleared and the the mode ends. At this time, using a dedicated cleaning card, use the cleaning card procedure according to the instructions on the screen. The count of use above is cleared also when the Test Mode is used for head cleaning.
Cleaning Card Reader/Writer Screen
CARD R/W
CLEANING PLEASE INSERT CLEANING CARD
+ Insert the cleaning card into the slot. The card is retracted automatically.
+ Now cleaning. Wait for a minute.
+ Cleaning is complete. Take out the card. You cannot proceed to the next step until you take it out.
D. REWRITING DATA ONTO THE CARD
The game board of this product backs up the data only when the card reader/writer detects a trouble DURING OPERATION and the Error Screen displays. However, no written data is backed up in the following case:
+ An action deemed to be illegal was detected while the game or write was in operation.
If backed up data remains when the power is turned on the Check Card Reader/Writer Screen will be replaced with the Save Data screen. Once written onto the cord, the backed up data is cleared before the mode ends.
Write the data onto the desired card according to the instructions on the screen. You can use the Start button to cancel the write. The backed up data is cleared in the following cases: + Normal write ended. + The backed up data was cleared in the Game Test Mode. + Data save taking place at power-on time was canceled, and the succeeding game ended.
Rewrite Data Onto Card Screen
CARD R/W
DATA SAVE PLEASE INSERT CARD
PRESS START TO CANCEL
Insert the cleaning card into the slot. The card is retracted automatically.
+ Now writing data. Wait for a minute.
+ Data write is complete. Take out the card. You cannot proceed to the next step until you take it out.
E. CARD LOW LEVEL ADJUSTMENT
+ Your game is equipped with a card “Low Level” system. It consists of a screw that moves with the magazine as cards are dispensed. When the screw gets low enough, the beam is interrupted and the LED is illuminated.
Added tape creates a flag to break beam sooner,
x
Low Level LED
\
x * \ ‘oo Hecreal Tage \|
+ Current configuration provides notification at approximately 10 card (+/- 2). If you feel you need sooner notification, see the diagram for suggested adjustment method.
E. TROUBLESHOOTING
Card Reader/Writer Trouble
When a card reader/writer failure is detected while the game is in progress, the error type is shown on the screen. Take the appropriate error according to the actions listed below. The game board of this product backs up the data only when the card reader/writer detects a trouble DURING OPERATION and the Error Screen displays. However, no written data is backed up in the following case:
+ An action deemed to be illegal was detected while the game or write was in operation.
If backed up data remains when the power is turned on, the Check Card Reader/Writer Screen will be replaced with the Save Data screen. The backed up data is cleared in the following cases:
+ After an action was taken against a trouble, normal write ended. + The backed up data was cleared in the Game Test Mode. + Data save taking place at power-on time was canceled, and the succeeding game ended.
Error Error condition + Action
“CONNECTION ERROR” Reader/ Writer Communication Error - Check the connection cables and then turn on the power again.
“MECHANIC ERROR1” DC Motor/Encoder Error - Check the connection cables and then turn on the power again. (Note 1)
“MECHANIC ERROR2” Thermal Head Elevation Error - Check the connection cables and then turn on the power again. (Note 1)
“CARD STUFFED” Card Jamming - Remove the card jam. (Note 2)
“MECHANIC ERROR3” Abnormal Temperature of Thermal Head - Check the connection cables and then turn on the power again. (Note 1)
“CARD EMPTY” Hopper Card Not Found - Supply card to the hopper. (Note 2)
“DRAW CARD ERROR” Error in Taking Out from the Hopper - Remove the card jame and check the hopper. (Note 2)
“CAN’T SAVE” No Data Can Be Written onto the Card. (Note 3)
“UNKNOWN ERROR” Error Other Than Above - Check the connection cables and then turn on the power again.
“SCIF ERROR” SCIF Error - Check the connection cables.
Without entering the Test Mode, turn on the power, again, to the cabinet if the following is included in the “Action” column in the above table: “turn on the power again.”
If the error is not included in the “Error” column in the above table, merely turn on the power again.
If no improvments result from the appropriate action listed in this document, contact one of the contact points listed in this document or the dealer from which you purchased the product.
Reaction Motor Trouble
When a failure is detected on the Check Motor Screen, which appears when the power is turned on. Use the following procedure to take action:
Error Display 1
STEERING DRIVE BD. IS NOT CONNECTED
PRESS START TO CANCEL OR PRESS VIEW TO RETRY
This is an error in communication between NAOMI 2 and the motor driver. Check the wiring. Pressing the Start button starts the game without steering-wheel reaction. Pressing the View button reinitiates the machine.
Error Display 2
STEERING DRIVE BD. DOES NOT WORK
PRESS START BUTTON TO CONTINUE WITHOUT REACTION FORCE
This is an error that occurs when the motor could not be initialized properly. Check the wiring between the driver motors. Pressing the start button starts the game without steering-wheel reaction.
When a failure is detected while the game is in progress, it continues to operate until it ends.
After the game ends, you are brought to the same screen as Check Motor that appeared at power-on time. Ifa failure is detected at this time, Error Display 2, above, appears. Take action against it. Usually, the encoder annexed to the motor is used for detection of the steering wheel; however, it will be unavailable if a failure is detected on the motor. The handle mechanism is provided with a spare volume for this reason. When the handle center is set with Set Volume Control Screen in the Test Mode, volume center setting, as well as encoder setting, takes place. However, when you make the machine operate without reaction because of a motor failure, center the volume control again by way of precaution.
PORTANT! F. GAME MENU
@ The new settings will not take effect until the Game Test Mode is exited. When you make change to the settings, exit the Game Test Mode by proper operation.
@ You must not attempt to demonstrate this game (for the selling purpose) with any other than those specified in this document. Use of such settings may cause malfunctions or bad operation on the machine.
SYSTEM MENU
RAM TEST
M ASSIGNMENTS COIN ASSIGNMENTS BOOKKEEPING BACKUP DATA CLEAR CLOCK SETTING
ROM BOARD TEST GAME TEST MODE [XXXXXXXXXXXXXXX]
-> EXIT
SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON GAME TEST MENU
CARD R/W TEST BOOKKEEPING BACKUP DATA CLEAR > EXIT
SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON
Pressing the SERVICE button moves the arrow on the screen. Move the arrow to select the item you want to run. Pressing the TEST button runs the currently selected item. The screen changes to the one for that item, and you can change or adjust the settings. Select EXIT and press the TEST button to return to the System Test Menu Screen.
G. INPUT TEST
@ By selecting INPUT TEST on the Menu Screen and pressing the Test button, the steering wheel is centered automatically as done when the machine is started. To protect persons from accidents make sure that nobody is in contact with the steering !
INPUT TEST tests the input devices. Using this screen, check the input devices periodically. Operate each input device. If the display at the right of the appropriate device changes from OFF to ON, it is diagnosed as being normal.
Check that each of the indications at the right of STEERING, ACCEL, and BRAKE change smoothly in response to operations of each of the input devices
change smoothly in response to operations of each of the input devices.
INPUT TEST
STEERING WHEEL: veme ACCEL. 7 eile BRAKE : +=e%
VIEW SW : OFF START SW H OFF
PRESS TEST AND SERVICE BUTTON TO EXIT
Pressing the TEST button returns you to the Game Test Menu Screen.
VOLUME CONTROL RECOMMENDED SETTINGS
- Steering wheel: Centered (when traveling in a straight line) 2000H
+ Accelerator: When the pedal is released 30H When the pedal is pressed fully COH
+ Brake: When the pedal is released 30H When the pedal is pressed fully COH
H. OUTPUT TEST
You can monitor the state of the lights. Use this screen to check the lights periodically.
OUTPUT TEST
START LAMP OFF VIEW LAMP OFF > EXIT
SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON
Pressing the SERVICE button moves the arrow. With the arrow aligned with the tested lamp item, press the TEST button. If the lamp lights up when the indication at the right of each name is ON and goes out when it is OFF, this lamp and wiring connections are normal. By selecting EXIT and pressing the TEST button, you return to the Game Test Menu Screen.
I. GAME SETTING
You can make the settings about cabinet operations such as the communicated mode or the reaction force of the steering wheel.
MAKING CHANGE TO THE SETTINGS
By pressing the SERVICE button, move the arrow (>) to the desired item to change.
- Pressing the Test button changes the display at the right of the currently selected item. Change the item to the desired display.
- Press the SERVICE button to select EXIT. Then press the TEST button. This returns you to the Game Test Menu Screen.
> EXIT GAME SBET1
LINK TYPE: XXXXXX STEERING POWER; #2384: saa
STEERING DIR. : REVERSE
CARD SYSTEM: ENABLE
BONUS GAMES: 0
SELECT WITH SERVICE BUTTON
PRESS TEST BUTTON TING
AND
@ LINK TYPE:
@ STEERING POWER:
@ STEERING DIR.:
@ CARD SYSTEM: @ BONUS GAMES: Used for settings of communicated play. You have four options:
MASTER, SLAVE, SATELLITE, and STAND-ALONE. If you
want to enjoy the game alone, set to STAND-ALONE. Setting for communicatedplay, be sure to set MASTER for only one machine, or seat, and set SLAVE for all the remaining ones. SATELLITE is a setting for a relay monitor. Sets reaction for the steering wheel. Increase or decrease in the number of asterisks (*) is reflected to the reaction force. The more the asterisks, the reaction force the larger. Sets steering reaction direction. Default for deluxe game is REVERSE. Activates card reader system.
Choose 0-3.
J. VOLUME SETTING
S
@ Jo prevent accidents, breakage of parts, and malfunctions, do not touch the
steering wheel until centering of the steering wheel is completed.
@ No normal play is guaranteed unless all the input devices are set properly. Be sure to makethe proper settings before you begin demonstration for the selling purpose. @ Once you have completed change to the settings, select EXT and press the TEST button. The new settings will not take effect until this mode is exited.
By setting the VOLUME SETTING on the Menu Screen and pressing the Test button, centering of the steering wheel in initiated automatically. After the centering is completed, you can use the screen below to make the steering wheel, accelerator, and brake settings. If the operability of the steering wheel, accelerator, or brake is poor, use this screen to make the proper settings for the volume control.
VOLUME SETTING
MIN MID MAX [2000] 2000 STEER: *--.
[2000]3000 ACCEL: a2 ennnncneneneeeneneeneee
[8100]3000 C000 BRAKE: ----*-------------------------' >
> EXIT
SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON
- By moving the SERVICE button to move the arrow, select the input device for which you want to make settings.
- For either the accelerator or brake, press START without pressing the pedal. Set the value resulting when you release it.
- With the pedal pressed fully, press START to set the value resulting when you press it fully. For the steering wheel, press START while supporting it along the straight line.
- Select EXIT and press the TEST button. The setting changes are not updated until you select EXIT. After you make change to the settings, be sure to select EXIT. By selecting EXIT and pressing the TEST button, you return to the Game Test Menu Screen. aa
K. CARD R/W TEST
Gror Check operation of the card reader/writer (R/W) and clean it periodically.
This screen lets you check operation of the card reader/writer (R/W) or clean it.
CARD R/W TEST
CARD R/W STATUS: ****##* INFORMATION
INITIALIZE CLEANING CHECK R/W: ---
> EXIT
SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON
The arrow can move to the following items: + INITIALIZE: _ Initialization
* CLEANING: — Cleaning
- CHECK R/W: _ R/W Operation Check
Depending on the R/W running mode, one of the following is displayed in “ *****” in “CARD R/W STATUS: **##*" :
READY Now waiting (Clear to Send Command) INITIAL Now initializing (Not Clear to Send Command) CLEAN Now cleaning (Not Clear to Send Command) GET Cards are being taken out from the hopper (Not Clear to Send Command) SAVE Sample data is saved onto the card (Not Clear to Send Command) LOAD Load card data and compares it with sample data (Not Clear to Send Command) OUT Eject cards (Not Clear to Send Command)
ERROR Error ( Clear to Initialize Command Only)
While a status with a note of “Not Clear to Send Command” in parentheses is on-screen, no operations are accepted. If such a status has occured, wait until the operation in that status stops automatically and the display comes to READY. Should you need to cancel the operation forcibly, turn off the power. If you cancel it forcibly, be sure to select and run INITIALIZE after turning on the power.
Occasionally, the “INFORMATION” field on the screen outputs one of the instructions below, although it usually contains nothing.
While cleaning is in progress, waiting in the ready mode for inserting a cleaning card:
----- PLEASE INSERT CLEANING CARD -----
After the operation check, waiting for the ready mode for ejecting the card:
----- PLEASE REMOVE CARD -----
When an error occurs, its type is displayed in the “INFORMATION” field:
CONNECTION ERROR Connection Error MECHANIC ERROR 1 DC Motor / Encoder Error MECHANIC ERROR 2 Thermal Head Elevation Error CARD STUFFED Card Jamming MECHANIC ERROR 3 AbnormalTemperature of Thermal Head CARD EMPTY Hopper Card Empty DRAW CARD ERROR Error in Taking Card from Hopper CAN’T SAVE Data cannot be written onto the card. UNKNOWN ERROR Unknown Error SCIF ERROR RC-232C Communication Error NO ERROR No Error
The “---” field in “CHECK R/W: ---” shows the result of the operation check.
_ Not Checked OK No Failure NG Failure
The operation check takes out each card from the hopper, and writes the sample data onto it. The check whether the read data matches the sample data. Then, the check ejects the card. When you draw out the card at this time, the entire process of the check is completed.
CHECKING R/W OPERATION
- Select “CHECK R/W” and press the TEST button.
R/W operates automatically as follows:
Takes out the card from the hopper: GET is displayed. Saves the sample data onto the card: SAVE is displayed. Loads the data on the card for comparison with the sample data: LOAD is displayed. Ejects the card: OUT is displayed. Draws out the card. Now the entire process of the check is completed. AAPRWN
If execution of the operation check results in display of NG, check the error condition. If you can take action against the error, execute the operation check again after you take the proper action. If you cannot take action against the error, repeat the check several times. If the result of the check is still NG, clean the R/W. If the subsequent execution of the operation check still results in NG, the R/W may be faulty.
If an error occurs, it is cleared by executing the INITIALIZE command. Note that when an error has occured, the R/W only accepts this command (except EXIT).
CLEANING PROCEDURE
- Select “CLEANING” and press the TEST button.
The following message appears to show that the R/W is ready for insertion of the cleaning card: ---PLEASE INSERT CLEANING CARD---
- Insert the cleaning card into the R/W. On the screen, the status display is replaced with “CLEAN”, and cleaning begins.
- Once cleaning ends after a lapse of a certain time, the R/W automatically ejects the card. The status. display changes from “CLEAN” to “OUT.”
L. BOOKKEEPING
In four pages, this screen lists the data about the operation status up to now. Pressing the TEST button brings you to the next page of the screen. When you press the TEST button on Page 4/4 of the screen, you return to the Game Test Menu.
BOOKKEEPING 1/4
NUMBER OF GAMES 0 NUMBER OF CARD GAMES, 0 NUMBER OF NEW CARDS v)
| PLAY TIME | OD | OH | OM | Os |
| AVERAGE PLAY TIME | OH | OM | Os | |
| LONGEST PLAY TIME | OH | OM | Os | |
| SHORTEST PLAY TIME | OH | OM | Os |
SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON
@ NUMBER OF GAMES: Number of games played.
@ NUMBER OF CARD GAMES: Number of games played with cards.
@ NUMBER OF NEW CARDS: Number of games played with cards.
@ PLAY TIME: Time played.
BOOKKEEPING 2/4
TIME HISTOGRAM
OMO0S - OM29S OM30S - OMS59S 1MOOS - 1M29S 1M30S - 1M59S 2MOO0S - 2M29S 2M30S - 2M59S 3MOOS - 3M29S 3M30S - 3M59S 4MOOS - 4M29S 4M30S - 4M59S OVER - 5MOOS coooooococ](“
SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON
T IME HISTOGRAM lists the number of plays for each of the play times.
BOOKKEEPING 3/4
PLAYS/CLASS
RENTAL BEGINNER RENTAL NORMAL CLASS NOVICE CLASS B CLASS A CLASS S CLASS SS. CLASS SSS. RRR RR RHE
SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON
PLAY/CLASS shows the count of plays by class.
BOOKKEEPING 4/4
PLAYS/COURSE
1-A 7 1-B * 1-C * 2-A 7 2-B = 2-C * 3-A * 3-B ae 3-C = 4-A * 4-B * 4-C *
SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON
The PLAYS/COURSE Screen lists the count of plays by course. Pressing the TEST button returns you to the Game Test Menu Screen.
M. BACKUP DATA CLEAR
BACKUP DATA CLEAR deletes data on the Bookkeeping Screen. To delete data about the coins/credits, run BACKUP DATA CLEAR in the System Test Mode. Clearing the data does not influence any data settings (except the data).
BACKUP DATA CLEAR
YES (CLEAR) > NO (CANCEL)
SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON
To delete the data, use the SERVICE button to align the arrow with CLEAR and press the TEST button. Once the data is deleted, this screen displays “COMPLETED.” Pressing the TEST button again returns you to the Menu Screen. If you choose not to delete the data, press the TEST button with the arrow aligned with NO. This returns you to the Menu Screen.
9. CONTROL PANEL (STEERING MOTOR UNIT)
Before starting to work, ensure that the Power SW is OFF. Failure to observe this can cause electric shock or short circuit. Use care so as not to damage wirings. Damaged wiring can cause electric
pinched in. Failure to observe this can cause a serious injury such as a
fracture. @ When performing work such as parts replacement other than those specified in this manual, be sure to contact where you purchased the product from and confirm the work procedures and obtain precautions prior to performing work. Inappropriate parts replacement and/or installing with erroneous adjustment can cause an overload or the parts to come into contact, resulting in an electric shock, a short circuit, and a fire.
9-1 ADJUSTING OR REPLACING THE V.R.
In cases the Steering operability is poor and the adjustment of VOLUME SETTING in the TEST mode is ineffective, the causes may be the Volume Gear's mesh failure and or Volume malfunctioning. By using the following procedure, adjust Volume gear mesh, or replace the Volume. In this product, when the Steering Wheel is moved fully left/right, if the Volume shaft is rotating within the movable range, the Volume is not feared to be damaged. Secure the Volume in the manner the Volume shaft is oriented as shown and the gears are appropriately engaged when the steering wheel is in the centering position allowing the car to go straight forward.
ADJUSTING THE VOLUME
Prepare a Phillips screwdriver and a wrench for M8 hexagonal nut.
® Turn off power.
Remove the 6 Trusshead screws and open the back of the main cabinet.
@)The V.R. is on the VR BASE (a white, plastic made part). Loosen the 2 screws which secure the VR BASE and adjust the angle and appropriateness of gear mesh by moving the VR BASE.
@adiust to an appropriate mesh by securing the Steering Wheel in the direction allowing the car to advance straight forward and ensuring the "D" CUT FACE of the Volume shaft is oriented as shown.
® Tighten the 2 screws to secure the VR BASE.
1 | SCREW (2) Sew M4 X 12, wiflat & spring washers
"D" CUT FACE,
FIG.9. 1a
© Turn on power.
@ Set the Center Value of the Volume in the TEST mode.
In the TEST mode, check to see if the Volume Value varies smoothly in accordance with the steering wheel operation.
REPLACING THE VOLUME SCREW (2) M4 X 12, w/flat & spring washers
® Disconnect the connector from the
Volume.
@ Take out 2 screws to remove the
Volume together with VR BASE from the HANDLE MECHA.
PHOTO 9. 1b
Take out 2 screws from the VR. BASE reverse side to remove the Volume together with VR Bracket from the VR BASE.
@ Remove the Volume from VR. Bracket and replace.
TRUSS SCREW (2). M4 X 12
PHOTO 9. 1c
® After replacing the Volume, engage the gears at the angular position shown and fix the VR Bracket.
SCREW) M4 X 12, w/flat & spring washers
FIG. 9. 1b
V.R, 220-5484 220-5373
© Turn on power.
Dset the Center Value of the Volume in the TEST mode. @®m the TEST mode, check to see if the Volume Value varies smoothly in accordance with the steering wheel operation.
9-2 GREASING
@ Be sure to use the designated grease. Using undesignated grease can cause parts damage. @ Do not apply greasing to undesignated places. Failure to observe this can cause malfunctioning or quality deterioration of parts.
. VOLUME GEAR MESH PORTION, Apply greasing to gear mesh portions once every 3 months. ' Use GREASE MATE (SEGA — én PART NO. 090-0066).
PHOTO 9. 2
- ACCELERATOR & BRAKE
If Accel. and Brake operation is not satisfactory, adjustment of Volume installation position or Volume replacement is needed. Also, be sure to apply greasing to the gear mesh portion once every 3 months.
10 - 1 ADJUSTING AND REPLACING THE V.R.
® Secure the Potentiobase.
® Secure the Potentiobase (O) Perform Volume setting in the
The appropriate value for both ACCEL. Volume and Brake Volume is under 30H when released and over COH when stepped on. Check Volume values in the TEST mode. Since work is performed inside the energized cabinet, be very careful so as not to touch undesignated places. Touching places not specified can cause electric shock or short circuit.
Take out the 2 truss screws and remove the Front Cover from the Accel. & Brake Unit
Loosen the screw which secure the Potentiobase, and adjust the Volume value by moving the Base. (FIG. 10. 1 b)
Volume setting mode.
SCREW / M5 X12, \/ wiflat & spring washers
.POTENTIOBASE
220-5484 220-5373
REPLACING THE VOLUME
@tum the power off. FIG. 10.1 ¢
@tum the power off @ Take out the 2 screws and remove the
Pedal cover (FIG. 10. 1c).
@Disconnect the connector of the ® Remove the screw which secures the
Volume to be replaced.
Pedal base (FIG. 10. 1 b).
® Remove the Pedal base together with
the Volume as is attached. (FIG. 10. 1 c)
© Remove the Base and Gear to replace @aAdiust the Volume as per the previous
the Volume.
page after replacing. an le
10 - 2 GREASING
Be sure to use the designated grease. Using undesignated grease can cause parts damage.
GREASING
IMPORTANT
Once every 3 months, apply greasing to the Spring and Gear mesh portion. For spray greasing, use GREASE MATE (PART No. 090-0066).
FIG. 10.2
- COIN SELECTOR
HANDLING THE COIN JAM
If the coin is not rejected when the REJECT button is pressed, open the coin chute door and open the selector gate. After removing the jammed coin, put a normal coin in and check to see that the selector correctly functions.
CLEANING THE COIN SELECTOR
@ Remove and clean smears by using a soft cloth dipped in water or diluted chemical detergent and then squeezed dry. Never apply machine oil, etc. to the Coin Selector. @ After cleaning the Coin Selector, insert a regular coin in the normal working status and ensure that the Selector correctly functions.
The coin selector should be cleaned once every 3 months. When cleaning, follow the procedure below: Turn the power for the machine OFF. Open the coin chute door.
Open the gate and dust off by using a soft brush (made of wool, etc.) Remove and clean smears by using a soft cloth
(made of wool, etc.).
dipped in water or diluted chemical detergent and then squeezed dry. Remove the CRADLE. When removing the retaining ring (E ring), be very careful so as not to bend the rotary shaft. Remove stain from the rotary shaft and shaft
receiving portions by wiping off with a soft After wiping off as per ® above, further apply
cloth, etc.
a dry cloth, etc. to cause the coin selector to dry completely. Insert a coin while keeping the Reject Button COIN INSERTION TEST
Once every month, when performing the pressed down and
Coin SW Test, simultaneously check the rejected. following: [Does the Coin Meter count satisfactorily? | |Does the coin drop into the Cashbox correctly? Is the coin rejected when inserted while keeping the Reject Button pressed down? COIN METER. \ °
FIG. llc
WELLS-GARDNER WGD15-2110-01 ELECTRONICS CORPORATION OVER/UNDER MINI DOOR
2701 N. KILDARE CHICAGO, IL 60639 2 ENTRIES WITH BILL 1-800-336-6630 WWW.WGEC.COM VALIDATOR BOTTOM DOOR
& SPECIAL ENCLOSURE
WG. PART # DESCRIPTION
812-4150-011 $-7 US 25c COIN MECH LEFT
$12-4050011 S10 US $1 CONNECH RIGHT
890-1002-00 HINGE SCREW
890-1003-00 CLAMP SCREW
890-1017-00 ‘SCREW TRILOBULAR
890-1019-00 WASHER INTERNAL TOOTH 3/4"
890-1300-00 KEYHOOK
891-0514-00 ‘CLAMP UK 5/8" CABINET
025X3711-001 ENCLOSURE W/CHUTE
025X3712-001 ‘METAL CASHBOX
891-0509-162 ‘DOUBLE FRAME
891-0547-00 LOCK SINGLE BIT
891-010-4016 COVER PLATE.
891-1008-107 BASE PLATE ASSEMBLY
891-1113-03 E/R BUTTON US 4x25c/$1 LEFT 891-1113-01T E/R BUTTON US $1 COIN RIGHT 891-1117-00 LAMPHOLDER-
891-1118-00 LAMP WEDGE BASE 6 VOLT
891-1121-00 ‘SPRING, E/R BUTTON
891-1311-16 BUTTON BEZEL, NYLON
891-1312-16 REJECT BEZEL, NYLON
891-1109-16 REJECT FLAP
020X1877-005 NUT KEPS #8-32 X 5/16 HEX
891-2216-16 MICROSWITCH ASSEMBLY
890-1007-00 ‘SCREW,FLAT HEAD M/S
890-1206-02. KEP NUT
891-1105-01 REJECT CUP SIDE PLATE
891-1106-00 REJECT CUP BASE PLATE
891-1107-00 BRACKET, MICROSWITCH
891-1110-00. “ADJUSTER, COIN 891-1116-16 ‘MICROSWITCH, BLACK - MED. 891-1125-00 COVER, PLASTIC
892-1002-07 ‘CUP, SNAP-ON:
892-1002-08 ELASTIC SNAP NUT
892-1002-09 ‘SLEEVE, SNAP-ON
892-1002-11 ‘SCREW, PAN HEAD 891-0604-16. ‘MINI DOOR 2 ENTRIES 891-0614-16 ‘MIN DOOR W/DBV C/O
892-1002-01 BRACKET, LAMPSIDE
892-1002-021 BRACKET, COVERSIDE
892-1002-10 BRACKET, HOLD DOWN:
Tom Happ Ph: 847-593-6161 ext. 107 tom.happ@happcontrols.com Fx: 847-956-2091 Happ Controls, 106 Garlisch Drive, Elk Grove, IL 60007 Visit our website http://www.happcontrols.com 42-0641-00 = 42-0405-00 FOR § 25 COIN 42-0405-05 FOR $1.00 COIN o.. 0231-00 et 42-1044-00 $1.00 4 x .25 1 PLAY 42-0895-5 $1.00 PUSH TO REJECT
g1-1319-00 © #2-0288-00 (7 43-0047. ‘ 42-051-00 a ° 43-1002-00 \ e 43-1003-00 . 42-7355-00 _ (s) 48-1000-00
42-0065-00. Nes
2T 42-7201-00 G- 42-0232-00 42-0119-00
$0.25 42.3079.00 $1.00 42-3113-00 42-7087-00 . 42.0641-00 43-0196-00—e" 42-0206-00 @=— 43-0021-00 42-86178-00
- 42-8174-10
aa 42-8177-00 Guardian Hasp 30-2400-200
42-8176-00
OPTIONAL DOLLAR BILL ACCEPTOR
@ THE COIN DOOR ASSEMBLY USED ON CLUB KART STD COMES EQUIPPED TO ACCEPT A DOLLAR BILL ACCEPTOR. ALL NEEDED WIRING CONNECTIONS ARE CONVIENENTLY LOCATED INSIDE THE GAME FOR THIS APPLICATION.
@ THE COIN DOOR CAN ACCCOMMODATE THE FOLLOWING VALIDATOR(S):
FORWARD-MOST Mars 2000 series HOLE POSITION
**42-1155-00 MARS VALIDATOR $1, 2,5 300 CAP
The frame and cashbox enclosure on this coindoor has been modified to accomodate a Mars 2000 series upstacker. A 2000 series stacker can be added by simply removing the cut-out plate. This one entry door can be ordered through Happ Controls or one of Happ Controls authorized distributors. The part number is 40-6000-10EX. The Mars stacker can be obtained through an autherized Mars distibutor.
**Happ part number
Security Locking Bar/Bracket Set Part No.# 999-0966
Modified Cash Box (For use when DBA installed) Part No. # 999-1106
Plastic Cash Box - Full Size Part No. # 999-1177
12. REPLACING THE FLUORESCENT LAMP, AND LAMPS
can cause electric shock and short circuit hazards. j\ When performing work, be sure to turn power off. Working with power on The Fluorescent Lamp, when it gets hot, can cause burn. Be very careful
secure and stable condition. Performing work without using the step can cause violent falling down accidents.
( To perform work safely and securely, be sure to prepare a step which is ina
INSIDE THE BILLBOARD
Remove the billboard holder, slide up the billboard plate, and replace the fluorescent tube.
FIG. 12a FLUORESCENT LAMP 24W:390-5251-32-01 GLOW LAMP:390-5638-5P_
START BUTTON, VIEW CHANGE BUTTON
® Turn power off.
@ Remove the 4 Trusshead screws.
START BUTTON VIEW BUTTON
TRUSS SCREW (4) M4 X 8, chrome
PHOTO 12a
Remove the switch plate from the control panel carefully without damaging the wires.
@on the rear side of the switch plate there is a metallic projection
on the foot of each button. Turn the projection to unlock, and remove the wire connection part from the button body.
The lamp is inside the wiring connecting portion. Push and then turn the Lamp counterclockwise to remove.
- PERIODIC INSPECTION TABLE
The items listed below require periodic check and maintenance to retain the performance of this machine and to ensure safe business operation. When handling the controller, the player will be in direct contact with it . In order to always allow the player to enjoy the game, be sure to clean it regularly. Also, it is advisable to provide wet tissue, etc. available for player use.
@ Be sure to check once a year to see if Power Cords are damaged, the plug is securely inserted, dust is accumulated between the Socket Outlet and the
without cleaning can cause a fire or accident. Note that cleaning the interior
parts can be performed on a pay-basis.
TABLE 13
| Item | Interval | Reference | |
| CABINET | Check Adjusters'contact with surface. | Daily | 3 |
CONTOROL PANEL Cleaning As necessary
| Inspection of SW, VR. | Monthly | 8 | |
| Greasing to the gear mesh portion. | Trimonthly | 9-2 | |
| ACCEL. & BRAKE | Check VOLUME VALUE. | Monthly | 8 |
| Gear and Spring portion greasing | Trimonthly | 10-2 | |
| COIN CHUTE DOOR | Check COIN SW. | Monthly | 8 |
| Coin insertion test. | Monthly | 11 | |
| Cleaning of COIN SELECTOR. | Trimonthly | ll | |
| PROJECTOR | SCREEN cleaning. | Weekly | |
| Check adjustments. | ‘Monthly or when moving. | 5,8, 10 | |
| SEAT | Greasing to the seat rail | Trimonthly | FIG.13 |
| GAME BD | MEMORY TEST. | Monthly | 8 |
| Check settings. | Monthly | 8 | |
| INTERIOR | Cleaning | Annually | See above. |
POWER SUPPLY PLUG Inspection and cleaning
| Cabinet surfaces | Cleaning | As necessary. | See below. |
CLEANING THE CABINET SURFACES
When the cabinet surfaces are badly soiled, remove stains with a soft cloth dipped in water or diluted (with water) chemical detergent and squeezed dry. To avoid damaging surface finish, do not use such solvents as thinner, benzine, etc. other than ethyl alcohol, or abrasives, bleaching agent and chemical dustcloth.
SEAT (Greasing to Seat Rail Portion)
Move the Seat to the rearmost portion and apply spray greasing to the portion shown at the right once every 3 months by using NOK KLUBER L60 or GREASE MATE SEGA PART No. 090-0066. After greasing, move the Seat a few times forward and backward so as to allow the grease to be applied all over uniformly. Be sure to wipe grease which attaches to the surfaces of the PROTECT RUBBER on the Seat Rail, or any excess grease. a
FIG. 13
- TROUBLESHOOTING
the Circuit Protector. Depending on the cause of the functioning, using the
Circuit Protector as is without removing the cause can cause generation of heat and fire hazard.
In case a problem occurs, first check wiring connector connections. TABLE 14a
PROBLEMS CAUSE COUNTERMEASURES
With Main SW ON, no activation. Power is not supplied.
Power supply/voltage is not correct.
The Circuit Protector functioned due to the momentary overload. Securely insert the power plug into the plug socket.
Make sure that power supply/voltage is correct.
After eliminating the cause of overload, reinstate the AC Unit's Circuit Protector (see [4], Sec. 5, Refer to the following). Reset the circuit protector on the ASSY ELEC. (see PHOTO 16 a, b)
The color on monitor screen is incorrect. Image adjustment is inappropriate. Adjust appropriately.
Color deviation on monitor screen. Affected by peripheral machines or the building's steel frames. Perform convergence adjustment
Change installation direction or position.
Move the machine which causes the problem.
No sound is emitted. Sound volume adjustment is not appropriate.
Board and Amplifier malfunctioning. Adjust sound volume (see Sec. 8).
Perform the sound test and confirm (see Sec. 8).
TABLE 14b
PROBLEMS CAUSE COUNTERMEASURES
Operability of the Steering wheel (handle) is poor. Deviation of the volume value.
Volume gear engagement fault.
Volume malfunctioning. Adjust the volume value in the Test mode. (see 8-3)
Adjust the engagement of the gear. (see 9-2)
Replace the Volume. (see 9-2)
Steering wheel (handle) is abnormal in its force feedback. It is not centered. Failure of power-on checking procedure.
The volume is not centered.
Failure of the volume. Reconnect the power, and complete a power-on checking procedure. (see [5] Sec. 5,)
Adjust the volume value in the test mode. (see Sec. 8)
Replace the volume. (see 9-1)
Steering wheel (handle) is week in its force feedback.
Aging of the force feedback
mechanism. Reset in the test mode. (see Sec. 8)
Gas pedal (accelletor) and/or brake pedal do not operate normally. The volume is not centered.
Failure of the volume. Adjust the volume value in the test mode. (see Sec. 8)
Replace the volume. (see 10-1)
The Fluorescent lamp does not light up. The Fluorescent tube is burnt out. Replace the Fluorescent tube (see Sec. 12).
Lights integrated with the start button and the view change button do not come on. The lamp is burnt out. Replace the lamp. (see Sec.12)
Failure of the Communication cables are Reconnect the cables. (see 18-2) communication disconnected. play. Communication cables are wrongly Reconnect the cables correctly. (See 18-2) connected.
Communication play is wrongly set. Reset correctly. (see 18-3)
"ERROR *' is Setting error in the test mode. Reset correctly in the test mode according displayed. to the product. (see Sec. 8)
- GAME BOARD
@ ‘norder to prevent electric shock and short circuit hazards, be sure to turn power off before performing work. @ Be careful so as not to damage wirings. Damaged wiring can cause fire, electric shock and short circuit hazards. @ Do not expose the Game BD, etc. without a good reason. Failure to observe this can cause electric shock hazard or malfunctioning.
The electronic parts on the IC Board could be damaged due to human body's static electricity. Before performing IC Board related work, be sure to discharge physically accumulated statics by touching grounded metallic surfaces, etc.
Put the Game Board in the Carton Box (an accessory) together with the Shield Case when requesting for the replacement or repair. Transporting the Game Board in an undesignated status for replacement/repair is unacceptable. In this manual, how to remove the Game Board is explained for convenience. However, this work should be performed by SEGA SERVICEMAN.
15 - 1 REMOVING THE GAME BOARD
@Tum power off. @ Remove the 2 trusshead screws of the back lid, unlock it, and detach it from the main cabinet.
® Disconnect the connectors of all the wires between the ASSY MAIN BD STD and the main cabinet.
® Disconnect the connectors of all the wires between the shield case's filter board on the ASSY MAIN BD STD and the main cabinet.
® Remove the 2 wing bolts that fix the base (a wooden plate) of the ASSY MAIN BD STD.
© Draw out the ASSY MAIN BD STD from the main cabinet. More than two workers
must engage in this action. Note that the ASSY MAIN BD STD is heavy, and, if a
single worker draws out it alone, he/she may damage the wires by snagging or catching the wires on other parts.
@ Remove the 4 screws that fix the shield case onto the base (a wooden plate), and detach the former from the latter.
® Remove the 2 screws each, and detach the shield case from the shield case brackets. Wrap the shield case with protective shipping materials, and contain it in a carton box. Send it for repairing.
- COMMUNICATION PLAY
For this game, up to 8 machines can be connected to allow up to 8 players to play simultaneously. In this instance, connecting the communication cable and setting for the communication play are required.
16 - 1 INSTALLATION PRECAUTIONS
Before starting to work, ensure that the Power SW is OFF. Failure to observe this can cause electric shock or short circuit. Use care so as not to damage wirings. Damaged wiring can cause electric shock or short circuit. Do not touch undesignated places. Touching places not designated can cause electric shock or short circuit. This work should be performed by the Location's Maintenance Man or Serviceman. Performing work by non-technical personnel can cause electric shock hazard. When linking a number of machines, be sure to supply sufficient power for the corresponding number of machines. Be sure to secure per machine current as stated in this manual. Failure to observe this can cause a fire and an electric shock accident. Due to the length of the communication cable, the distance in between the machines is limited. However, to avoid accidents, be sure to secure space in excess of 70 cm between the machines. To perform work safely and avoid serious accident such as the cabinet's falling down, do not perform work in places where step-like grade differences, a ditch, or slope exist.
To perform work safely, be sure to onding to number of machines to be linked. dent.
Excessive bending may damage the communication cable. Be very careful in this regard. S The optic fiber cable is used for the communication linkage.
IMPORTANT
Since 2 or more machines are to be linked, sufficient power corresponding to the number of machines used need to be supplied. Note that as a standard, the per machine capacity should be 15A for the 100 ~ 120V area, and 7A for the 220 ~ 240V area.
DISTANCE BETWEEN MACHINES
Be sure to secure space in excess of 70cm between machines.
\
ume
oy 7 ot Aor = ; a \ \ E TT h
70cm
16 - 2 SETTING FOR COMMUNICATION PLAY
During communication play, if the test mode is not finished within 3 minutes on all the linked machines, the NETWORK CHECK cannot be performed, causing NETWORK ERROR.
IMPORTANT
Change the game setting for each seat in a manner so as to meet communication play. If the setting is not correct, communication play cannot be played.
SETTING FOR COMMUNICATION PLAY
® Turn the linked machines' power on.
@) Cause all of the machines to enter the test mode.
® Select the SYSTEM ASSIGNMENTS.
® Turn the linked machines' power on @) Cause all of the machines to enter the test mode ® Select the SYSTEM ASSIGNMENTS ® Perform the COMMUNICATION MODE setting in the SYSTEM ASSIGNMENTS screen. Set
one of the machines to MASTER and all others to SLAVE. Set to RELAY for exclusive use of LIVE Monitor.
SYSTEM ASSIGNMENTS
CABINET TYPE IPLAYER ADVERTISE SOUND ON MONITOR TYPE HORIZONTAL DISPLAY MODE AUTOSCAN SERVICE TYPE COMMON > COMMUNICATION MODE MASTER EXIT
SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON
FIG. 16.2a
® Activate the game test mode. (8-3)
© Select and open the GAME ASSIGNMENTS screen. Note that the screen looks different between the MASTER and SLAVE game machines.
@ Perform the SEAT NUMBER setting in the GAME ASSIGNMENTS screen. Set the machines sequentially to No.1, No.2, No.3, and so on as applicable starting from the extreme left facing the monitor's front side. Set every seat number correctly without duplication.
GAME SETTINGS
LINK TYPE: STAND ALONE STEERING POWER: ****#####4#%% STEERING DIR.: REVERSE CARD SYSTEM: ENABLE BONUS GAME: 0
EXIT
SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON
FIG. 16.2b
Cause all of the machines to exit from the test mode. After the test mode, the screens proceed to and display the NETWORK CHECK.
When a network-checking is finished, the system displays am advertisement screen. This means a successful completion of setting. If any seat number is duplicated, an error message appears on the screen. Normally the NETWORK CHECK takes less than one minute. If the screen does not proceed from the NETWORK CHECK screen, some sorts of errors such as incorrect setting, or incorrect connection or malfunctioning of the communication cable can be considered.
16 - 3 CAUTIONS TO BE HEEDED DURING COMMUNICATION PLAY
IMPORTANT
With a communication play, the ADVERTISE SOUND and GAME DIFFICULTY items can be set only on the MASTER game machine. New settings by the MASTER game machine become effective to all the interconnected game machines. If any setting is inadequate or if the communication cables are improperly connected, the system keeps displaying the network-checking screen or an error message. If this is the case, you cannot play the game. During communication play, if communication is interrupted due to some cause, the game is discontinued and the NETWORK CHECK screen is displayed.
If one of the linked machines enters the test mode, all others display the
NETWORK CHECK screen.
Machine's operation when linked for communication play alters comparing to that of when independently operated. Be careful of this point. As described above, some setting items must be set only on the MASTER game machine. They cannot be set on any SLAVE game machines or, if set, will not become effective. When any game machine is in a test mode, a network-checking screen appears on the other game machines interconnected for a communication play. While a guest is using any one of the interconnected game machines, therefore, do not activate a test mode even on the unused game machine.
- DESIGN RELATED PARTS
For the Warning Display stickers, refer to Section 1.
ITEM NO.
NOT SHOWN
NOT SHOWN
NOT SHOWN
NOT SHOWN PART NO.
999-1263 999-1265 999-1264 999-1250 999-1256 999-1251 999-1268 999-1269 999-1267 999-1266 999-1270 999-1271 DESCRIPTION
MARQUEE DECAL SIDE LEFT - MONITOR DECAL SIDE RIGHT - MONITOR DECAL NUMBER SHEET #2-8 SEAT DECAL NUMBER SHEET ##2-8 PEDESTAL DECAL REAR SEAT DECAL TOP REAR BASE DECAL BACK REAR BASE DECAL LEFT SEAT BASE DECAL RIGHT SEAT BASE DECAL CONTROL PANEL DECAL INSERT CLUB CARD
C) Top Assy
- PARTS LIST
(D-1/1)
() Top assy
ITEM NO.
NOT SHOWN
NOT SHOWN
NOT SHOWN
NOT SHOWN PART NO.
LOC. PURCHASE 999-1258 999-1257 999-1262 999-1287 999-1285 999-1286 999-0167 999-0169 SPGS5-2200-A SPGS5-2200-B SPG-2001 N/A 130-5162 130-5156 (D-2/2)
DESCRIPTION
FLUORESCENT FIXTURE 20 WATTS 24” CARD READER ASSY REAR SEAT COVER (GREEN) S/A; TUBE - BUTTERCUP YELLOW FLOOR MAT COVER PEDAL FRONT COVER PEDAL BACK LEG LEVELER 1/2-13 X 3” (6 PER) CASTER 160-2 1/2 #25188 SWIVEL (8 PER) ACCELERATOR PEDAL BRAKE PEDAL STEERING WHEEL COIN METER GULL BOX SPEAKER 8 OHM 8W (SEAT) SPEAKER BOX 8 OHM 20 WATT
@) Ac UNIT
ITEM NO. PART NO.
1 999-1043 NOT SHOWN DYN-0402 NOT SHOWN 421-8202
104 999-0676 DESCRIPTION
AC BRKT NOISE FILTER BASE STICKER EARTH MARK
SW ROCKER J8 V-B
- FAN UNIT (STR-1070)
ITEM NO. PART NO. DESCRIPTION
| 1 | 105-5340-01 | FAN BRKT LONG |
| 101 | LOC. PURCHASE | FAN AC120V |
102 601-8543
| 201 | 000-P00312-W | M SCR PH W/FS M3 X 12 |
@) ASSY CONNECTOR PLATE (NCR-1080)
ITEM NO. PART NO.
NCR-1081 421-7515
211-5479-01
000-P00312-W DESCRIPTION
CONNECTOR PLATE STICKER FIBER CABLE TX/RX
CONN OPT JOINT
M SCR PH W/FS M3 X 12
G) sw UNIT
ITEM NO. PART NO. DESCRIPTION
| 1 | LOC. PURCHASE | COIN METER 6 VOLTS |
| 2 | LOC. PURCHASE | PUSH BUTTON SW |
| 3 | LOC. PURCHASE | 5 K POTENTIOMETER & VOLUME KNOB |
- ASSY CTRL PNL (NCR-2000)
ITEM NO.
NOT SHOWN i Se
agdadda
PART NO.
LOC. PURCHASE NCR-2006 SPG-2001 SPG-2002 LOC. PURCHASE DESCRIPTION
PUSHBUTTON SML ROUND YEL VLT COMP. 57-2000-35 STEERING COLLAR STEERING WHEEL STEERING EMBLEM PUSHBUTTON RECT. VLT BLUE 57-2000-62
- STEERING MOTOR UNIT (NCR-2100) (D-1/2)
SCREW FASTENING TORQUE TO BE
DG
(206) We)
@) STEERING MOTOR UNIT (NCR-2100) (D-2/2)
ITEM NO. PART NO.
FRI-2101 FRI-2102 NCR-2101 FRI-2104 SPG-2504 SPG-2505 SPG-2506 FRI-2105 SPG-2453 ASK-3502 ASK-3503 DYN-1270 SLC-1130 SPG-2454 FRI-2106
350-5448-01 100-5112 601-8966 601-6172 601-6959 601-9173 220-5373 220-5484 310-5029-F20 280-0419 280-5009-01
028-A00408-P 028-A00308-P 065-S012S0-Z 065-S020S0-Z 000-P00408-W 000-P00412-W 030-000612-S 060-F00600 030-000820-S 030-000840-S 068-852216 060-F00800
NCR-60055 DESCRIPTION
MECHA BASE BASE LID MOTOR SHAFT SHAFT LOCK PLATE PULLEY 20 SSM PULLEY 60 SSM MOTOR BRKT VR BRKT KEY 4X4X 40 MOTOR SPACER MOTOR COLLAR STOPPER KEY ADJUST RING MOTOR SHAFT COLLAR VR BASE
SERVO MOTOR 500W NEW BEARING 17 GEAR HOLDER GEAR 48 GEAR 64 TIMING BELT VOL CONT B-5K VOL CONT B-SK OHM SUMITUBE F F 20MM HARNESS LUG CORD CLAMP 21
SET SCR HEX SKT CUP P M4 X 8 SET SCR HEX SKT CUP P M3 X 8 STP RING BLK OZ S12 STP RING BLK OZ S20 MSCR PH W/FS M4 X 8 M SCR PH W/FS M4 X 12 HEX BLT W/S M6 X 12 FLT WSHR M6 HEX BLT W/S M8 X 20 HEX BLT W/S M8 X 40 FLT WSRR 8.5-22 X 1.6 FLT WSHR M8
WIRE HARN HANDLE VR
(Z/1-@) (007Z-DdS) ANVUAY TADOV ASSV @)
- ASSY ACCEL&BRAKE (SPG-2200) (D-2/2)
ITEM NO.
NOT SHOWN NOT SHOWN NOT SHOWN PART NO.
SPGS5-2201-A SPGS5-2201-B SPG-2202 SPG-2203 SPG-2204 SPG-2205 SPG-2206 SPG-2207 SPG-2208 SPG-2209 SPG-2210 SPG-2211 SPG-2212 SPG-2213 SPG-2214 SPG-2215 999-1260 999-1273 999-1274 SPG-2219 SPG-2220 SPG-2221
100-5263 220-5484 220-5373 601-7944 310-5029-F15 280-0419
028-A00304-P 020-000520-0Z 000-P00420 000-P00508-W 000-T00408-0C FAS-450005 000-P00405 FAS-000001 050-H00500 060-F00400
600-6840 DESCRIPTION
BASE ACCELERATOR BASE BRAKE ACCEL PEDAL BRAKE PEDAL. ACCEL SPRING BRAKE SPRING SHAFT ACCEL GEAR BRAKE GEAR NEUTRAL STOPPER VR PLATE ACCEL VR PLATE BRAKE AMPL GEAR GEAR SHAFT STOPPER RUBBER CUSHION PEDAL PLATE LEFT PEDAL PLATE RIGHT PEDAL PLATE REAR (2) GEAR STAY WSHR NEUTRAL STOPPER D
BEARING 12 VOL CONT B-SK OHM VOL CONT B-5K GEAR 15 SUMITUBE F F 15MM HARNESS LUG
SET SCR HEX SKT CUP P M3 X 4 HEX SKT H CAP SCR BLK MS X 20 M SCR PH M4 X2 MSCR PH W/FS MS X 8 MSCR TH CRM M4 X8 SPR PIN BLK OZ 6 X 10 M SCR PH M4 X 5 M SCR TH CRM M3 X 6 HEX NUT MS FLT WSHR M4
WIRE HARN ACCEL&BRAKE
(@) ASSY SEAT (NCR-2400) (D-1/2)
SCREW FASTENING TORQUE TO BE
M4 Sonic Lock Portion: 0.9Nem
M8 Others: 19.9Ne«m
@) ASSY SEAT (NCR-2400)
ITEM NO. PART NO.
1 999-1257 2 NCR-2402 3 NCR-2403 4 NCR-2404 5 SRT-2402 6 999-1048 9 FRI-3309 12 STC-1608 13 STC-1609 15 DUT-2205 16 STC-1607 17 INY-1302-B
103 280-5297 104 130-5162 106 280-5009-01 107 280-5275-SR10 108 601-698 1-009 109 601-6563-225
201 030-0008 16-S 202 030-000850-S 203 050-H00800 204 060-S00800 205 068-852216 206 000-T00408-0B 207 000-P00410-W 208 000-T00516-0B 209 000-T00616-0B 210 000-P00408-S 211 060-F00400 212 050-U00400 213 030-000855-S 214 012-P00412 (D-2/2)
DESCRIPTION
SEAT BACK COVER UPPER SEAT LOWER SEAT SEAT BASE SEAT FRAME TURTLE COVER CABLE BEAR BRKT SPEAKER NET L SPEAKER NET R SHAKER BASE REAR SP MOUNT BRKT MASK CUSHION SIDE.
SCRIVET 8 1K31 GULL BOX SPEAKER 80HM 8W, CORD CLAMP 21 CORD CLAMP SR10 CABLE BEAR L=009 BUSH 2.4T
HEX BLT W/S M8 X 16 HEX BLT W/S M8 X 50 HEX NUT M8 SPR WSHR M8 FLT WSHR 8.5-22 X 1.6 MSCR TH BLK M4 X8 M SCR PH W/FS M4 X 10 MSCR TH BLK MS X 16 M SCR TH BLK M6 X 16 MSCR PH W/S M4 X 8 FLT WSHR M4 U NUT M4 HEX BLT W/S M8 X 55 TAP SCR #2 PH 4 X 12
CARD READER ASSY (999-1258)
ITEM NO. PART NO.
1 253-5512 2 601-11039 3 999-1259 4 999-1272 NOT SHOWN 601-11051-01 NOT SHOWN 6017-11050 DESCRIPTION
CARD GUIDE CARD R/W UNIT CR-1231R OPTIC UNIT OPTIC BRACKET CARDS (200 PACK) CLEANING KIT
(@) ASSY MAIN BD STD
ITEM NO.
YAURWNHY PART NO.
600-7141-250 837-13844 400-5368-07512 400-5397-01 998-0148 600-7009-2500 840-0062D-01 DESCRIPTION
CABLE JVS TYPE A-B 250 CM PCB I/O CONTROL BD 2 FOR JVS SW REGU LCA75S-12 (Used for Card Reader) SW REGU DC 3.3V 12A 5V 10-A 12V 2A TRANSFORMER MCT 4-06-8036 ASSY RGB CA D-SUB 15 PIN 2500 MM ASSY CASE NAT CKT USA
@) Assy AMP BD
ITEM NO. PART NO. DESCRIPTION
1 838-14174 SERVO MOTOR DRIVE MD MIDI 2 838-13475 PWR AMP 4CH & MIXER
(D-1/2)
- ASSY ELEC (NCR-4200)
AAO 01 (COP) 99EET-SER PUL (AP) PSE I-LER) SOMOS dIC Op [TP 19S °Z
SNOLLYOd YUVW HSVIS AHL NI “OLA “ONTAIA\ ON SIAAAHL LVL TANS AAV “TALON COW
- ASSY ELEC (NCR-4200)
ITEM NO. PART NO.
1 NCR-4201 2 NCR-4202 3 837-13844 4 838-13366 5 838-12912-01 7 421-7468-01
102 998-0135 103 117-5225
104 512-5046-15000 105 310-5029-K20 106 280-5009-01 108 601-0460
201 011-T00316 202 011-T00325 203 000-P00516-W 204 000-P00416-W 205 O11-T03512 206 011-F00312 (D-2/2)
DESCRIPTION
WOODEN ELEC BASE C.P.BRKT 1/O CONTROL BD 2 FOR JVS FRI DRIVE BD SRT SERVO MOTOR DRIVE BD NEW STICKER C.P W/PIC
POWER TRANSFORMER ER-501 FUSES 1-6.25 A SLOW BLOW 2-3A SLOW BLOW 1-15A SLOW BLOW C.P 1S5000MA CE UL SUMITUBE F K 20MM CORD CLAMP 21 PLASTIC TIE BELT 100 MM
TAP SCR TH 3 X 16 TAP SCR TH 3 X 25 M SCR PH WIFS MS X 16 M SCR PH W/FS M4 X 16 TAP SCR TH 3.5 X 12 TAP SCR #1 FH 3 X 12
- WIRE COLOR CODE TABLE
THE WIRE COLOR CODE is as follow:
moawe
PINK
SKY BLUE
BROWN
PURPLE
LIGHT GREEN
Wires other than those of any of the above 5 single colors will be displayed by 2 alphanumeric characters.
Cerdunpewne RED
BLUE
YELLOW
GREEN
WHITE
ORANGE
BLACK
GRAY
If the right-hand side numeral of the code is 0, then the wire will be of a single color shown by the left-hand side numeral (see the above).
<Example> 51 we
RED WHITE
The character following the wire color code indicates the size of the wire.
U: AWGI16
K: AWGI18
L: AWG20
None: AWG22
VISIT OUR WEBSITE!
0 ?O Se agaService.com
SERVICE
- Dari's Office '" What's New
- Game Manuals *" Bultetines
Sega Enterprises Inc. USA Semice Department phone 415.701.6580 tax 415.701.6594 { ‘ 1 ! UstaffllDarl's off [technical service)[customer service]icorporate info][plugins)[Non-framed page]
A total of Bake 61 people have accessed this page since June Sth.
Ifyou have any questions or comments about this Home Page please E-Mail to
darl davidson@seu sega. com OR dave. cantrelle@seu sega com
Sega Enterprise Inc., USA. All rights reserved
THIS WES SITE POWERED OY 8 \icbSTAR 3
You will need the following items to view this page in its entirety
SEGA ENTERPRISES, INC. (USA)
45133 Industrial Drive Fremont, CA 94538 (415) 701-6580 phone (415) 701-6594 fax