Tekken 5 Card Reader Kit
Tekken 5 (Namco) · Kit Manual · 9 pages · 11 sections · original scan
namco
TEKKEN 5
CARD READ/WRITE
FITTING & CONNECTIONS
Paget Issue 4
Kit Contents
Description Part No Quantity
Read/Write Assembly XTEK5-CARDRWASSY 2
S-CONV PCB XTEK5-SCONVPCB 2
| EXCARD PCB to S-CONV PCB Loom | 69200134 | 1 |
| Read/Write Surround Decal - Player 1 | 40000817 | 1 |
| Read/Write Surround Decal - Player 2 | 40000818 | 1 |
| Card Decal | 40000792 | 1 |
| Card Read/Write Decal | 40000793 | 1 |
1.
2.
3. Ensure that all functions of the game are working correctly
and the machine is switched OFF before commencing any work.
Fit the Card Read/Write assemblies to the cabinet. The cut-out dimensions are shown below.
ins 62mm =
Cut-Out Dimensions
Fit the S-CONV PCBs into the cabinet and connect the Card Read/Write assemblies to the S-CONV PCBs.
Connect the EXCARD to S-CONV PCB loom to the Game PCB.
Game PC board
Player 1 Player 2 12way \ 10way
a EXCARD to S-CONV PCB Loom
- Connect the EXCARD to S-CONV PCB loom to both S-CONV PCBs.
Game PCB Connectors Power Supply Connection
S-CONV PCB Connectors
Not Used
Disconnect the 9way connector from the Power Supply and connect this connector to the EXCARD to S-CONV PCB Loom, and connect the other 9way connector on the EXCARD to S-CONV PCB Loom to the Power Supply.
Switch the game on and check the Card Read/Write operation by conducting the Card Options Test.
Card Options Test
This test is used to set the Read/Write unit and TEKKEN-NET IDcard.
- Select Card Options from the Main Test Menu. The following screen is displayed.
CARD OPTIONS
| (a) | +> P1 card RW found | P2 card RIW found | ||
| (b) | [> Sensor | OFF | Sensor | OFF |
| (c) | [> Solenoid | UNLOCK | Solenoid | UNLOCK |
Insert CARD Insert CARD
Exit: P4 - Start
Item Options Description
P1 card RW found (P2 card R/W found) [found] or [not found] Displays [found] if the card R/W unit is connected to the Game PC board, and displays [not found] if it is not connected.
- Sensor [ON] or [OFF] Displays [ON] when a card is inserted in the card RW unit, and displays [OFF] when there is no card in the card R/W unit
- [UNLOCK] or [LOCK] [UNLOCK] or [LOCK] As soon as the card is inserted into the card R/W unit, the card is locked into position and the screen displays "LOCK". If the card is not locked in position, the screen displays "UNLOCK"
- To conduct a test or data restoration, insert a card into the Read/Write unit
CARD OPTIONS
P1 card R/W found Sensor OFF Solenoid UNLOCK
cardNo 0000 0000 0000 0000 cardNo 0000 0000 0000 0000
Press Button 1 to WRITE/READ TEST Press Button 2 to REJECT
Exit: P2 card R/W found Sensor OFF Solenoid UNLOCK
Insert CARD
P1 - Start
- Note: The above is an example of the screen display when two cards are inserted into the P1-side card R/W unit
Display after card insertion
Item Description
(CardNo 0000 0000 0000 0000 (CardNo 0000 0000 0000 0000 When a card is inserted in the card R/W unit, the 16-digit number (access code) printed on the reverse of the inserted card is displayed on the screen. When two cards are inserted, the access codes for both cards are displayed in two rows
If a card is inserted in the P1-side card R/W unit, press the P1 Button switch 1 to conduct the card read/write test. If a card is inserted in the P2-Side card R/W unit, press the P2 Button switch1 to conduct the card read/write test. To eject the card from the card R/W unit, press the Button switch 2 on the side in which the card is inserted.
Exit: P1 card R/W found P2 card R/W found Sensor OFF Sensor : OFF Solenoid UNLOCK Solenoid : UNLOCK
READ DATA ERROR Insert CARD cardNo 0000 0000 0000 0000
Press Button 1 to WRITE/READ test Press Button 2 to REJECT Press Button 3 to Restore Data *Note 1 CARD OPTIONS
P1 - Start
- Note 1: This item is only shown when an error card is inserted
Item Description
CARD READ ERROR This indicates that a card other than a TEKKEN-NET ID card was inserted land data could not be read.
CARD WRITE ERROR This indicates that the Write test has failed.
READ DATA ERROR This indicates that comparison of the data after the write test resulted in a mismatch.
WRITE READ OK This indicates that both read and write operations were successful.
- Note 1: Conducting the card read/write test will not damage the game play data on the card.
- Note 2: When two cards are inserted, the card read/write test cannot be performed.
If a card on which a write error was generated is inserted or if a card on which data was destroyed due to power-off during data writing is inserted, pressing the Button switch 3 of the applicable player side initiates an attempt to restore the data on the card.
Card data may or may not be restored depending on the condition of the card, as described below.
Data may only restored with the card that was used to play the game with the Game PC board that you are working on and has been set to the test mode. It should be noted that there is a limit to the amount of data saved (10 cases max.). If a write error was indicated during a game play, it may be possible to restore the data successfully. If power interruption ocured when data was being written to the card, it may be possible to restore the data successfully. If the card was pulled out during a game play, the data cannot be restored. Data restoration can be tried only once for one error. Data restoration cannot be conducted with a card whose access code is different from the data stored in the cabinet. Data cannot be restored with a card which disallows data reading or writing due to damage.
To return to the test menu screen, press P1 Start switch.
Tekken 5 Card Read/Write Connections EXCARD PCB S-CONV PCB Loom
" Ps Ie_cARO CABLE
[RESET
System256 RACK Assy | EXCARD
PCB Assy
L Rin 1 N IC CARD UNIT<P1>
EE Ie_CARO CABLE
wh.
EI szl[sfol<[ [ol] } IC CARD UNIT<P2>
OO T [oR [oN
- 479 2u17 (1N9 2017 caw) S-CONV Com
(pauy
you ar H PCB Assy -&e
(9) oO}
To Power Supply
Copies of Namco Game Manuals can be downloaded from our website: www.namco.co.uk They are located under Components, Sales and Service
For all Parts or Technical Support contact:
Brent Electronic, Namco House, Units 5-8, Acton Park Estate, The Vale,
London. W3 7QE
www.brentelectronic.co.uk
For Technical Support, Warranty and
Advance Replacement Parts:- J +44 (0) 20 8324 6120
For Consumable Parts:- J +44 (0) 20 8324 6102
Fax for both:- [L} +44 (0) 20 8324 6126