CATHODE RAY TOMES

Road Runner CO-285-01 1st Printing

Road Runner (Atari, 1979) · Change Order · 8 pages · 20 sections · original scan

Page 1

€O0-285-01 Ist printing

Road Runner’ Hall-Effect

Joystick Calibration

Procedure

‘The Hall-effect joystick control provides your Road Runner player’s character. re, i

game with more precise movement and speed control of the

“Trademark of Warner Bros. used by Atari Games Corporation under

Page 2

Calibration Procedure

Re ictceveon attach See the joystick does not respond correctly, perform the following procedure frst ensue tat the joysticks propedy cen

tered. After turning on the self-test switch located on the

Audio Printedl-Circuit Board (PCB) Assembly and then the

game power, press the 1-player start button until the screen

displays the Joystick Test. (See Figure 1.) The Joystick Test

screen indicates the center position and range of the Halleffect joystick.

vertical set-up values in hexadecimal are dis-

Page 3

should equal or be very close to 80 when the joystick is centered. If the joystick is not centered, calibrate it as follows:

  • Remove the control panel and tum itupside down so that it rests on the front edge of the cabinet with the bottom of the joystick control facing up.
  • Using a screwdriver, adjust the two potentiometers located in the lower comers of the Hall-Effect Joystick PCB Assembly so that both horizontal and vertical set-up values equal or are very close to 80. (See Figure 2.) The po-

tentiometer in the left corner (R7) controls the horizontal

value; the one in the right corner (R6) controls the vertical clockwise increases the set-up value. To decrease the set

value. Turning the inset screw of the potentiometer clockwise increases the set-up value. To decrease the setup value, turn the inset screw of the potentiometer counterclockwise.

Page 4

(Cronueyy ssorviedo J marsis nok uy 7 sordeyD, 01 Joyor ‘Ayquuasse sty BurAOUIa! UO UONeUOJUT JO) “UIqed oY Wo A[quIAssY God UEW-FeF Oy) 2AOWDT ‘QUO sjuaUMNsUy eee By “sjusuinnsuy sexay, Aq zi SEASU/PT UORWO] 1 ANDO parvsBaur ayy JI 998 01 YooyD °q ‘Tourd ssaoov quoy ayy puryaq ourqus 2up JO JoUIOD pury>YysE Joddn oyp ur A[quossy god Bs rages Mpa ha BS sBuUFMOTTOJ BY) YooUD ‘are UdAIB ‘at yovar 01 oBuer YBnouds oavy 10U Soop UBIS + dYI JT °Z “asixo 148! woyqord oemp.ey v ‘vare ud9I3 ay puockaq spuorxe uBis + oy JI ‘JoAaMoH “3991200 st yonsdof oy Jo ours oy ‘var U9e38 oY) UT sUTeUNAI USIS + oY JT “voIe Ud918 OY OUT SAAOUT UBIS + ot IY Os yonsAOl oy DAOC “| 13991700 st aBuer yonsdof oy wy? oMsud 01 aM. -s001d SuTMOTOY oy) WOJIed “y>NsAof ay2 BuTFOIUDD JOY a8ury yonssofisnfpy “paaotype st Buria1u99 jun yonsdof yi JO JouIOD Yyove Joy amMpavoad sip WyOJIEg “9 “srojowsonuaiod yonséof 2yp asnipe “xog a1mtjas ay Jo apIsino sureutos UBIS + oyIJT “S “uonrsod JoqUD OY} 01 suINIAI 11 WY? Os YoNsdof oy asea[Dy “IYBIE MO JO Yo] Jomo] ‘Iyspr Jaddn ‘yoy Joddn :xoq us213 ol ‘BUTMOTIOJ ay} JO 9UO 01 yonsAOf =P ZAC “fF S + ¥ S9WOIOq II ‘KOq aITYA dY1 JO INO soAouT JOSIND oY1 USYAM “XOq TY oy JO JON. sy) UL 9q pinoys Josino asenbs ypxIq ‘Tews y ‘BuprqUad Joy pasn. st usaios oy uO padeydsIp xog arya otp UTI are Oy, “¢

Page 5

‘sured asatp JopI0-95 01 JO JoULISTSSE [EOTUYOAI JOT “2OYJO SDIAJag JOWIOISND: leiy Isozeau amok JOKIUOD ‘aBuEI yonsdol ay asv2I0 -U] JOU S20p stp JT (-¢ eINBIy 22g) “wWejqord oy Der 409 01 ZCY UONLDO] JO wUBISap Ie JOISISor YY ¢°¢ ay ssoine a]Aas yoeqA88id sorsisor YY Z'Z ¥ JOpjos ‘USyL, ‘Pp

Page 6

2> AT GAMES

Atari Games Corporation

P.O, Box 361110

Milpitas, CA 95035

Page 7

d. Then, solder a 2.2 kQ resistor piggyback style across the 3.3 k@ resistor at designator location R52 to correct the problem. (See Figure 3.) If this does not increase the joystick range, contact your nearest Atari Customer Service office.

——— SSS

Figure 3 Installing Resistors Piggyback Style

a

NOTE Installing a resistor piggyback style is necessary on TTL Main PCBs only. LSI Main PCBs, used in System I games built from June 1986 on, do not require this piggyback modification.

For technical assistance or to re-order these parts, call Atari Field Service at (408) 434-3950 (Monday-Friday, 7:30 am—4:00 pm Pacific time) A

ATARI

GAMES

Atari Games Corporation 737 Sycamore Drive P.O. Box 361110 Milpitas, CA 95035 CO-285-01 Ist printing

Road Runner’ Hall-Effect Joystick Calibration

Procedure

The Hall-effect joystick control provides your Road Runner game with more precise movement and speed control of the player’s character. Therefore, it is important that the centering and the range of the joystick be correct. You can assure this by performing the joystick calibration procedure.

i

CAUTION Do not adjust either of the long metal spacer screws positioned perpendicular to the bottom of the joystick control or you can damage it. These screws should only be adjusted if you remove the Hall-Effect Joystick PCB. For instructions on how to adjust these screws, refer to “Reassembling the Joystick” in Chapter 3 of the Road Runner Operators Manual.

“Trademark of Warner Bros, used by Atari Games Corporation under license

Page 8

Calibration Procedure

The joystick control is calibrated at the factory. However, if the joystick does not respond correctly, perform the following procedure first to ensure that the joystick is properly centered. After turning on the self-test switch located on the Audio Printed-Circuit Board (PCB) Assembly and then the game power, press the 1-player start button until the screen displays the Joystick Test. (See Figure 1.) The Joystick Test screen indicates the center position and range of the Halleffect joystick.

soustick fest

Figure 1 Joystick Test Screen

Adjust Joystick Centering

Horizontal and vertical set-up values in hexadecimal are displayed in the top left-hand corner of the screen. Both values Potentiometer should equal or be very close to 80 when the joystick is centered. If the joystick is not centered, calibrate it as follows:

  • Remove the control panel and turn it upside down so that it rests on the front edge of the cabinet with the bottom of the joystick control facing up.
  • Using a screwdriver, adjust the two potentiometers located in the lower corners of the Hall-Effect Joystick PCB Assembly so that both horizontal and vertical set-up values equal or are very close to 80. (See Figure 2.) The potentiometer in the Jeft corner (R7) controls the horizontal value; the one in the right corner (R6) controls the vertical value. Turning the inset screw of the potentiometer clockwise increases the set-up value. To decrease the setup value, turn the inset screw of the potentiometer counterclockwise.

Potentiometer

#6-20 Spacer re Screw

HallEffect PCB Assy

2¥e-Inch Screw Yelnch Screw

Figure 2 Hall-Effect Joystick PCB

  • The area within the white box displayed on the screen is used for centering. A small, black square cursor should be in the center of the white box. When the cursor moves out of the white box, it becomes a + sign.

4. Move the joystick to one of the following Seuione

green box: upper left, upper right, lower left, or lower right. Release the joystick so that it returns to the center position.

  • Ifthe + sign remains outside of the white box, adjust the joystick potentiometers.
  • Perform this procedure for each corner of the joystick until centering is achieved.

Adjust Joystick Range

After centering the joystick, perform the following procedure to ensure that the joystick range is correct:

  • Move the joystick so that the + sign moves into the green area. If the + sign remains in the green area, the range of the joystick is correct. However, if the + sign extends beyond the green area, a hardware problem might exist. Contact your nearest Atari Customer Service office.
  • If the + sign does not have enough range to reach the green area, check the following: \ a. After turning off the game power, locate the BS Main PCB Assembly in the upper right-hand corner of the cabinet behind the front access panel. b. Check to see if the integrated circuit at location 14/15D is manufactured by Texas Instruments. c. If the integrated circuit is a Texas Instruments one, remove the Main PCB Assembly from the cabinet. (For information on removing this assembly, refer to Chapter 2 in your System I™ Operators Manual.) ze