CATHODE RAY TOMES

AquaJack

Aqua Jack (World) (Taito Corporation Japan, 1990) · Manual · 21 pages · 4 sections · original scan

Page 1

ROMNSTAR

TAN ACK

OPERATING MANUAL

ROMSTAR, wc. 22857 Lockness Avenue, Torrance, CA 90501 (213) 539-2744 © FAX: 213-539-3626

Page 2

SPECIFICATIONS

POWER SUPPLY 120 VAC (60Hz)

POWER CONSUMPTION 250 WATTS

TV MONITOR 19"/24" COLOR RASTER

DIMENSIONS 26 1/4"W x 37"D x 72"H

TABLE OF CONTENTS Page Numbers

GAME INSTALLATION POM OUMONE ALO © 0 6 HK NEES TSS Ke elelesiolediiceseeivae 2

CABINET ILLUSTRATIONS nc Sc <1

GAME OPERATION & PLAY INSTRUCTIONS COO Pore e err wreewiseeensdvone 7

SELF-TEST MODE 2H Me C180 We Oo Ow HE COTE TES Osa s cee esogerecrviscere 8 — 10

CONTROL GRIP ALIGNMENT Ce coeee 9

SERVICE ACCESS DRAWER AND POWERHOUSE ASSEMBLY eee cee ee eeeeeee LI -— 12

OPTION DIP-SWITCH SETTINGS Coe ewe e reece rere cenneseccccsesessee 13 — 14

SUB-ASSEMBLY ILLUSTRATIONS & PARTS IDENTIFICATION ............ 15 - 18

  • WARNING *

THIS GAME MUST BE PROPERLY GROUNDED. FAILURE TO DO So MAY RESULT IN DESTRUCTION TO THE ELECTRONIC COMPONENTS.

  • ATTENTION *

THE COPYRIGHTED VIDEO GAME THAT ACCOMPANIES THIS MANUAL CARRIES WITH IT A ROYALTY FREE, NON-EXCLUSIVE LICENSE FROM THE COPYRIGHT OWNER TO THE OWNER OF THE VIDEO GAME TO PUBLICLY PERFORM THE COPYRIGHTED VIDEO GAME IN THE UNITED STATES OF AMERICA, CANADA, AND MEXICO. THIS PUBLIC PERFORMANCE LICENSE ATTACHES AND APPLIES ONLY TO THE PHYSICAL EMBODIMENT OF THE VIDEO GAME THAT ACCOM- PANIES THIS MANUAL. THIS PUBLIC PERFORMANCE LICENSE MAY ONLY BE TRANSFERRED TO THE SUBSEQUENT OWNER(S) OF THE PHYSICAL EMBODIMENT OF THE VIDEO GAME THAT ACCOMPANIES THIS MANUAL.

Page 3

Li. GAME INSPECTION

Aqua-Jack has been thoroughly tested and readied for operation at the factory and should not require any special set-up procedure. However, it is suggested that upon receiving your game you examine the following to further insure the game is in proper working condition:

CHECK:

Plug-in connectors are firmly seated. All player control connections are complete. No loose components on the printed circuit boards. Fuses are installed firmly in holders. Coin mechanisms are operating properly. No loose foreign objects in cabinet (screws, components, etc.) which may cause shorting and result in damage to the game. manmne

If problems do occur or technical assistance is required, please call our Customer Service Department at 213/539-2744.

II. POWER REQUIREMENTS

The game is shipped ready for operation at 120VAC, 60Hz with a power consumption of approximately 250 watts.

CAUTION

FOR SAFE OPERATION IT IS STRONGLY RECOMMENDED THE CABINET BE PROPERLY GROUNDED. THIS GAME IS EQUIPPED WITH A THREE CONDUCTOR POWER CABLE. THE THIRD PRONG (round in shape) WILL AUTOMATICALLY GROUND THE GAME WHEN PLUGGED INTO A PROPERLY GROUNDED THREE PRONG RECEPTACLE. IF IT BECOMES NECESSARY TO USE AN ADAPTER, THE GROUNDING LUG OR WIRE ON THE ADAPTER MUST BE PROPERLY GROUNDED TO ASSURE SAFE OPERATION.

III. GAME INSTALLATION

The following precautions should be followed when installing the game:

  • Handle the game with care so as not to damage the fragile picture tube.
  • Do NOT install the game in direct sunlight or near a heat source. Doing so might cause the internal temperature of the game to exceed it’s maximum operating temperature and could result in damage to the game’s components.
  • Do NOT install the game in excessively dusty or damp environments.
Page 4

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 5

CABINET FRONT PARTS LIST

ta UPRIGHT CABINET 185-197648 | ? initia i. ~ oo one | eisai ee eh ae |

185-194019 4 FLOURESCENT LAMP ASSEMBLY |eoweee | ane ae nen ee ee renee wn en ene ce conan | coseeeccce | pooceeee ence | 5 MONITOR FRAME W/ARTWORK 185-198002 |

185-110008 | | 185-1g1901 |

Page 6

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 7

CABINET REAR PARTS LIST

DESCRIPTION

Page 8

Iv. GAME INSTRUCTIONS

AQUA-JACK is a shooting/maneuvering game in which the player advances down-river in a hovercraft and launches an attack behind enemy lines. His goal is to rescue the hostages held at enemy headquarters by an evil alien commander who has managed to brainwash all humans in his command.

The player uses a control grip to maneuver the hovercraft and aim, a trigger to shoot and two thumb buttons for launching missiles and jumping clear of floating mines and enemy fire. A unique sighting system allows the player to sight a target, lock-on and destroy it, all without impeding the player’s control of the vehicle. Each stage grows progressively more difficult and ends when the player successfully destroys an enemy blockade, a feat which gains him access into the next stage. Eight completely unique stages comprise the game, each featuring varied terrain and different enemy activity. The eighth and last stage is nothing short of spectacular as the player comes face to face with the extraterrestrial villain responsible for the attack.

Breathtaking graphics and an action-packed storyline unfold in accelerating progression, assuring total player involvement.

And Romstar’s Continue Play feature keeps the player in the action.

  • TO AIM: Use the control grip to position the sight over the enemy target. When the sight is locked on its target, the word FIRE will appear and an audible command to fire will be heard.
  • Pull TRIGGER to fire vulcan gun.
  • Press MISSILE button to launch a missile. (Limited supply)
  • Press JUMP button to jump over floating mines and other obstacles.
  • When each stage is cleared, a map is displayed showing your progress and destination.
Page 9

V. GAME PCB ADJUSTMENTS

SOUND VR

VR1 (RIGHT) VR2 (LEFT)

® } ® }

VI. SELF-TEST MODE

A. TO ENTER THE SELF-TEST MODE

  • Turn power OFF.
  • Locate Dip Switch Bank A on the main logic PCB and slide switch #3 to the ON position.
  • Turn power ON.

The game will automatically conduct a test of its rom and ram memory and indicate if a problem is found.

  • ROM/RAM & COLOR MONITOR TEST - This screen is the first to appear in the self-test mode.
  • CONTROL GRIP ADJUSTMENT - Pull the TRIGGER one time to enter this test.
  • SWITCH/FUNCTION TEST MODE - Pull the TRIGGER two times to enter this test.

B. ROM/RAM & COLOR MONITOR TEST

  • During the first stage of this test, the game conducts a self-test of its ROM and RAM memory and indicates if a problem is found.
  • During the second stage of this test, the screen displays a color bar and crosshatch pattern to assist in adjusting the color monitor.
Page 10

c. CONTROL GRIP ADJUSTMENT PROCEDURE

1. Open the coin door. Locate the two latches under the service access drawer. Unlock the drawer and slide out. Locate the two adjustment knobs for control grip horizontal and vertical. (See illustration on page 11 for location.)

Allow the control grip to rest in the neutral (center) position. Rotate both adjustment controls until the moving cursor is positioned directly over the stationary cursor in the center of the screen.

Once adjusted, move the control grip out of the center position and then let go. The cursor should return to the approximate center position when released.

Check your adjustments by moving the control grip and confirming the cursor travel is approximately equal in all directions.

Page 11

D. SWITCH/FUNCTION TEST MODE

1. Press each game control switch to test. While depressed, the corresponding display for that switch will change from OFF to ON. This indicates the switch is operating properly. (See illustration.)

TEST MODE

COIN A :OFF COIN B :OFF

SERVICE: OFF

TILT : OFF

VULCAN: OFF

MISS1LE; OFF

JUMP: OFF

ACCEL: OFF

8 7 6 5 4 38 A H H H H H L DIP-SwW B H H H H H H

SOUND CODE:00

RAM OK

ROM OK

To test the game sounds, move the control grip to the right or left until the desired sound address appears next to the SOUND CODE display. Then press the MISSILE button to activate that sound.

E. TO EXIT THE SELF-TEST MODE

1.

2.

3. Turn Power OFF.

Locate Dip Switch Bank A on the main logic PCB and return switch #3 to the OFF position.

Turn Power ON.

Page 12

CONTROL GRIP HORIZ. CONTROL GRIP VERT.

Page 13

POWERHOUSE ASSEMBLY DRAWER PARTS LIST

|=saece seaeeesssessssssss | KEY DESCRIPTION |=sese= Saeeeeceessesesneessssssesessessesss | 1 D/A CONVERTOR

Page 14

DIP SWITCH SETTINGS

The following option switch settings were designed to allow the customizing of AQUA-JACK’s various game features to suit different environments. If used wisely, the flexibility they offer can maximize game performance and increase potential earnings.

IP SWITCH A |__ FUNCTION | ___ SETTING z

COCKTAIL *UPRIGHT

MUST REMAIN IN "OFF" POSITION

TEST MODE

ATTRACT *ENABLED SOUNDS DISABLED

PLAY PRICING

CONTINUE PRICING

  • = FACTORY RECOMMENDED SETTINGS.

CONTINUE PRICING - THIS SWITCH ALLOWS YOU TO PRICE THE "CONTINUED" GAME DIFFERENTLY THAN THE INITIAL GAME. AN EXAMPLE WOULD BE AN OPERATOR WHO ALLOWED HIS PLAYERS TO CONTINUE AT A DISCOUNTED RATE. EXAMPLE: PLAY PRICING IS SET AT (2 COINS = 1 PLAY) AND THE CONTINUE PRICING AT (1 COIN = 1 PLAY). THE PLAYER PAYS THE FULL AMOUNT (2 COINS) TO BEGIN PLAYING, THEN PAYS ONLY HALF AS MUCH (1 COIN) TO CONTINUE HIS GAME. WHEN THE CONTINUE PRICING IS SET AT "SAME PRICING", THE CONTINUED GAME IS PRICED THE SAME AS THE INITIAL GAME.

Page 15

DIFFICULTY *B - MEDIUM A - EASY Cc - HARD D - HARDEST

  • 50,000 PTS 80,000 PTS 100,000 PTS 30,000 PTS

MUST REMAIN IN “OFF" POSITION

*NORMAL ENDLESS

FACTORY RECOMMENDED SETTINGS.

Page 16

i $d INSTALL WITH CONTROL GRIP UPPER ASSEMBLY

Page 17

CONTROL GRIP UPPER ASSEMBLY PARTS LIST

DESCRIPTION | REF NO. | PART NO. | [===

| 8 BLADE, TRIGGER RETURN SPRING 58993961 185-818008 |

| 9

| 18 TUBE, HANDLE 96254000 185-818019 |

BEZEL, THUMB SWITCH

Page 18

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 19

CONTROL GRIP LOWER ASSEMBLY PARTS LIST

185-818820 |

185-818621 |

185-818828 11 DEAD STOP BRACKET 96459866 | -----= | --------- ---- eee | He] We | 12 DEAD STOP 96458000 185-818829 | ----~-- | --------------------------------- ++ ee | eee peel | 13 POTENTIOMETER 5K 58882709 185-81803»0

185-818631 |

185-818836

185-818837 |

185-818038 |

185-8186839 |

185-818048 |

185-818641 |

185-818642 | SSS ae I

Page 20

FLUORESCENT LAMP & SPEAKER ASSEMBLY

Page 21

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.