Cruisn Exotica 27in
Cruisin' Exotica (Midway Amusement Games, LLC, 2000) · Manual · 105 pages · 61 sections · original scan
JANUARY 2000 MIDWAY 16-40072-101 “AMUSEMENT GAMES, LLC
27” DEDICATED
GAME OPERATIONS MANUAL
Manual Includes Operation & Adjustments + Parts Information + Wiring Diagrams » Testing & Problem Diagnosis
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
DECLARATION OF CONFORMITY
MIDWAY AMUSEMENT GAMES, LLC
3401 N. CALIFORNIA AVE. CHICAGO, IL 60618 U.S.A.
WE, HEREBY DECLARE UNDER SOLE RESPONSIBILITY THAT
THE MODEL: ‘cRUISIN' EXOTICA 27" VIDEO! 40272, 40372, 40472, 40772, 40972, 41072, 41172, 41272, 41372, 41472, 41872, 42072, 42172, 42272, 423 72, 47172, 47272
TO WHICH THIS DECLARATION RELATES IS IN CONFORMITY WITH THE FOLLOWING EUROPEAN PRODUCT SAFETY DIRECTIVES:
ELECTROMAGNETIC COMPATIBILITY DIRECTIVE (89/336/EEC AND AMENDMENTS 91/C 162/08, 92/31/EEC,93/68/EEC)
ELECTRICAL EQUIPMENT DESIGNED FOR USE WITHIN
EI DI T! (73/336/EEC AND AMENDMENTS 88/C 168/02, 92/C210/01, 93/68/EEC,94/C199/03, 95/C214/02)
AS IS VERIFIED BY COMPLIANCE WITH THE FOLLOWING STANDARDS:
EN55014: 1993 EN61000-4-2: 1995 IEC 801-3: 1984 (EN61000-4-3) EN61000-4-4: 1995 EN61000-4-5: 1995 EN335-1: 1995 IEC 335-2-82 (DRAFT)
Date issued: JANUARY 24, 2000
ae
CORPORATE V.P. OF QUALITY
QUICK REFERENCE CABINET LINKING INSTRUCTIONS
To link two cabinets, use the crossover coupler included in the spare parts bag. Connect the Zt factory installed linking cable to the coupler and follow the instructions for “Wiring Modifications
- | and Software Setup” located below starting with step #7.
To link three or more cabinets, use a standard 10 base-T ethernet hub and follow all of the instructions for “Wiring Modifications and Software Setup” located below.
CABINET ARRAYS To create a Video Game Machine (VGM) Array, join the cabinets together. Each VGM comes equipped with the necessary hardware to connect cabinets and provide maximum stability. Hardware is located in the spare parts bag inside the cash box.
To join cabinets, remove the flat-head carriage bolts from the top and rear of adjacent cabinet sides. Position cabinets next to one another and adjust the leg levelers until all holes are aligned. Insert long carriage bolts through the holes in both cabinets, and then fasten in place with the nuts provided.
NETWORK CONSIDERATIONS Each VGM comes complete with a factory installed network cable. Optionally, a hub can be installed and located remotely to monitor network activity. Cables up to 328 ft., or 100 meters, in length may be used in conjunction with the hub provided they are Category 3 or higher, 100 ohm unshielded twisted pair communications grade wiring. Standard telephone cables are not sufficient for this application and should not be used.
Take care to protect exposed wiring from player foot traffic, cleaning crews, service personnel, etc. Use approved conduit or wire channels to support cables. Please note that modular connectors do not have strain relief.
Prevent linking cables from becoming damaged by avoiding sources of extreme heat or moisture, and high amounts of electrical energy like neon signs, fluorescent fixtures, two-way radios, cordless phones, power circuits, public address system wiring, etc.
Universal RJ-45 modular plugs are not numbered or coded in any way. Clearly label all network connections to avoid confusing network cables with computer or telephone circuits.
WIRING MODIFICATIONS AND SOFTWARE SETUP
- Place the linking hub inside the base of a cabinet nearest the center of the array. Remember that the crossover couplers supplied with the game are not used when creating an array using the hub. Crossover couplers are only used to link two cabinets.
- Unlock and remove the rear door from the cabinets selected to be part of the array. Inside the cabinet you will find a coil of linking cable with one end already attached to game electronics. Uncoil just enough of the cable to reach the hub, then recoil the rest of the cable and tie it in place. Repeat this procedure for each of the other cabinets. Do not reinstall the cabinet door(s) at this time.
- Route the free end of each cable out through the notch located in the rear door opening and plug into any jack on the rear panel of the linking hub. Route the free end of the AC adapter for the hub and plug it into the 9VAC jack on the front panel of the hub. Now all of the cables can be connected to the hub.
- Refer to the manufacturer's instructions in order to set the hub switches for LNK (link) and X (crossover) activity.
- Fasten the hub to the bottom of the most central cabinet using a hook-and-loop type material. Orient the hub so that the indicator lights are visible and cable jacks are accessible.
- Make sure excess cable is tied into a coil and that all cables are routed through the notch in the rear door. Connect the AC adapter for the hub and all line cords to AC power.
Switch on power and closely observe the screen for each cabinet during start up. Each automatically enters ATTRACT MODE if no errors are found. Refer to Troubleshooting in the operation manual if errors are detected.
Unlock the coin door for each cabinet to access the operator control buttons inside coin vault. Press and hold the TEST button to enter the menu system. » Check the EPROM, GUTS, and MAIN information at the bottom of each game’s SELF TEST menu screen. » Verify linked games have compatible software versions. Newer versions may contain instructions previous versions do not, causing games to halt or reset at random. >» Repeat this and all remaining steps for each linked cabinet.
Press the View 1 or View 2 button to select GAME OPTIONS. Press the ABORT button to activate this item. Set the CABINET #; keeping in mind that each cabinet must have its own individual and unique number. The first cabinet on the left is always cabinet 1, the second is cabinet 2, etc.
Select NETWORK TESTS then press the ABORT button to activate it. Observe all linked cabinets will be listed in this screen. Refer to Menu System descriptions in the manual for more details.
Select CONTROLS TESTS. Follow on-screen instructions to confirm proper control operation. Press and hold the TEST button to reset steering wheel and pedal travel limits.
Select SOUND TESTS. Confirm operation of all cabinet and seat speakers, and each amplifier.
Select MONITOR TESTS. Perform all tests and adjustments to ensure high quality video.
Close and lock the coin door, and reinstall and lock the rear door for each cabinet. Lower the leg levelers for each cabinet until the casters do not touch the floor and the cabinets are level. Lock the levelers in position by tightening the nuts provided.
NOTES
CRUIS’N EXOTICA
SECTION
ONE
OPERATION
NOTICE: This manual is subject to change without notice. MIDWAY reserves the right to make improvements in equipment function, design, or components as progress in engineering or manufacturing methods may warrant.
Fill out and mail in the Information Card. Include the Video Game Machine (VGM) serial number from the label on the rear of the cabinet. For your records, write the serial number in the manual. SERIAL NUMBER
SAFETY INSTRUCTIONS Safety instructions apply to operators and service personnel. Read these instructions before preparing the Video Game Machine (VGM) for play. Other safety instructions appear throughout this manual.
Definitions of Safety Terms
| @ | DANGER indicates an imminent hazard. | If you fail to avoid this hazard, it WILL cause death or |
serious injury.
| @ | WARNING indicates a potential hazard. | If you fail to avoid this hazard, it COULD cause death or |
serious injury.
| @ | CAUTION indicates a potential hazard. | If you fail to avoid this hazard, it MAY cause minor or |
moderate injury. CAUTION also alerts you about unsafe practices.
@ NOTICE indicates information of special importance.
Operations - 2
If you or anyone in your family has experienced symptoms linked to an epileptic condition (e.g., seizures or loss of awareness), immediately consult your physician before using any video games.
We recommend that parents observe their children while they play video games. If you or your child experience the following symptoms: dizziness, altered vision, eye or muscle twitching, involuntary movements, loss of awareness, disorientation, or convulsions, DISCONTINUE USE IMMEDIATELY and consult your physician.
Operations - 3
PRODUCT SPECIFICATIONS
Operating Requirements Location Electrical Power Temperature Humidity
Domestic 120VAC @ 60Hz4.0Amps 32°F to 100°F Not to exceed 95% relative Foreign 230VAC @ 50Hz 2.0 Amps _(0°C to 38°C) Japan 100VAC @ 50Hz 4.0 Amps
Cabinet Statistics
| Shipping Dimensions | Shipping Weight (Approx.) | Design Type |
| Width 30" (76.2 cm) | 350Lbs (158kg) Main Cabinet | Sit-Down Dedicated Video Game |
| Depth 64" (162.5 cm) | 125Lbs (57kg) Seat Assy. | Machine with Steering Wheel |
Height 78" (198 cm) Feedback
Game Characteristics
| Player Variables | Operator Variables | Diagnostics |
1 Player per VGM (Up to 4 with Linking) | Coinage, Play Mode, Automatic Power-Up Self-Test
| High Score Recognition | Difficulty, Volume, | Manual Multi-Level Menu System |
AAMA Certified: Suitable for all Ages Audits, Statistics
Equipment Characteristics Video Display Monitor Medium Resolution RGB NK 27” (68.6 cm) CRT .
Audio System Digital Stereo 5” (12.7 cm) Coaxial Full Range Speakers os
Currency Acceptors a 2 Coin Mechanisms Dollar Bill Validator Ready Electronic Coin Acceptor Ready
PRODUCT CONFIGURATION
@ Stand Alone Video Game Machine Each VGM is ready to play right out of the box. Operators may use the menu screens in the game menu system to determine some player variables in advance or leave the choices up to the players.
@ Linked Video Game Machines Linking allows players to compete against each other on a single course. Operator menus are used the same way as in stand-alone VGMs. Crossover couplers and linking cables to connect two VGMs are factory installed. Use an optional 10 base-T ethernet hub to interconnect up to eight VGMs (two groups of four).
Operations - 4
Video Game Machine Array
SET-UP
- Inspect the exterior of the main cabinet and the seat pedestal for signs of damage prior to assembly.
- Remove the keys from the steering wheel. Unlock the coin, cash box, and rear doors to access the electrical cords, mechanical components, and spare parts packed inside the cash box.
- Install one nut onto each leg leveler. Tilting as needed, locate the threaded holes under the cabinet and pedestal, insert a leveler into each hole. Do not tighten nuts at this time.
- Roll cabinet to intended location, maintaining a clearance to work in, and lower each leveler until the cabinet is stable and level. Adjust levelers as necessary to equally distribute the weight.
Operations - 5
LEVELER PLATES
LEG LEVELER SNNEL CASTES fe °
Location of Casters and Levelers
Reach inside the base of the cabinet and remove the bolts used to fasten a mounting rail to the cabinet and set aside. Individually pull the rail out, flip it end for end, and reinsert it. Fasten the rail to the inside of the cabinet with bolts until finger tight; some movement is required in the mounting rails to align holes with pedestal assembly. Repeat for the mounting rail on the other side. See diagram for proper placement.
CABINET BASE J
2 CABINET NOUNTING HOLES
Location of Pedestal Assembly Mounting Holes
Operations - 6
- Roll the pedestal near the cabinet and align the opening in the pedestal with the ends of the rails. Slide the pedestal forward onto the rails leaving enough space to attach the wiring harness. Mate each cable connector and press firmly to seat the contacts. Ensure no wires are pinched during pedestal attachment. Fasten in place with the %4 -20 tamper resistant screws and large flat washers provided in spare parts. Tighten the screws firmly with the wrench provided, and then tighten the bolts for the mounting rails.
- Lower each leg leveler until the pedestal is stable and level with the cabinet. Adjust all levelers until both pieces are flush and parallel with each other. Inspect for pinched wires, and then insert and firmly tighten the remaining fasteners to attach the two pieces as one.
- Remove the hasp used to secure the rear door from the spare parts bag. Remove the lock bracket nuts from above the rear door opening. Slide the hasp bracket onto the bolts until it protrudes through the hole in the cabinet, and then reinstall nuts.
Rear Door Hasp Installation
- Modify the lock plate by removing the hardware at the top of the rear door, rotating it so the slot is above the door and reinstalling the nuts and bolts.
- Reinstall the rear door onto the cabinet and lock it. If necessary, insert an extra padlock in the hasp at this time. Install the screws at the top and sides of the rear door and tighten snugly.
- Remove the power cord from the spare parts bag and insert a portion of it in the cord clamp. Make sure there is enough slack before plugging the cord into the receptacle.
Line Cord Installation
Operations - 7
12.
13.
20.
21. Plug the VGM into a grounded (3-terminal) AC wall outlet. Press the ON/OFF switch located near the top of the cabinet to switch on power to the game cabinet. After the Self-Test Mode the game automatically enters Attract Mode if no errors are found.
Open the coin door. Locate the operator control switch panel and then press and hold the Begin Test button to enter the menu system. Wait until the Main Menu screen appears on the monitor.
Coin Door Switch Location
. Follow on-screen instructions to select Diagnostics, then choose SWITCH TEST. Follow the onscreen instructions to verify that each of the controls is operational. If no errors are found, the controls should function well.
. Return to the Diagnostics screen, then choose MOTION TEST. Follow the on-screen instructions to verify that motion seat is operational. If no errors are found, the seat should function well.
. Return to the Diagnostics screen, then choose SOUND BOARD TEST. Follow the on-screen instructions to verify that each of the speakers is operational. If no errors are found, the audio should function well.
. Return to the Diagnostics screen, then choose STEERING WHEEL TEST. Follow the on-screen instructions to verify the presence of steering resistance. If no errors are found, the aim will be good.
. Return to the Main Menu screen, then choose CALIBRATE CONTROLS. Follow the on-screen instructions to set steering limits. If no errors are found, the controls will have the maximum accuracy.
. Return to the Main Menu screen, and then choose EXIT. The game will automatically enter its “attract” mode of operation (scenes and sounds from typical races, player's scores, messages, etc.).
Insert currency or tokens and play a game. Change the volume and make any other adjustments. Close and lock all open doors. Tighten the leveler nuts and engage the caster locks.
Insert currency or tokens and play a game. Change the volume and make any other desired adjustments. Close and lock all open doors. Make sure the leveler nuts are tightly fastened and engage the caster locks.
Operations - 8
MAINTENANCE
@ Viewing Glass It is not necessary to switch off power to the VGM to clean the glass. Apply a mild glass cleaner to a clean cloth or sponge and wipe the viewing glass. Do not apply the cleaner directly on the glass! Liquid could drip down into switch or control circuits and cause erratic game operation.
@ Player Controls Use plastic-safe, non-abrasive cleaners to avoid damage. Apply cleaner to a clean cloth or sponge and wipe the player controls. Do not apply the cleaner directly on the controls!
@ Cabinet and Seat Use plastic-safe, non-abrasive cleaners to avoid damage. Apply cleaner to a clean cloth or sponge and wipe the seat or cabinet. Do not apply cleaner directly on artwork or cabinet!
GAME FEATURES
CRUIS’N EXOTICA™ ships configured for one-player game play. Cabinets may be linked to permit player competition. A lighted header option is available.
Cruis’n Exotica™ is the latest, most thrilling and adventurous driving game in the Cruis’n™ video game series. Players can select tracks located in nearly a dozen exotic locales around the globe. From Tibet to Atlantis, Mars to Hong Kong, it is every player’s goal to rack up high scores and mileage points.
Speeding on their way toward a first place finish, drivers listen to cool tunes on the radio as they pass palms swaying in the breeze, 3-Dimensional animals cavorting roadside, and a variety of shortcuts hidden along the way. A player’s combined speed and skill virtually assure a place in the winner’s circle.
Player incentives, like free games for top speeds and distance, are sure to captivate players and ensure many trips around the track. A player finishing in first place soon discovers they have been whisked away on a free trip to an exotic locale. (Player incentives are Operator Optional and enabled at the Operator's discretion)
For added excitement the dashboard now features a keypad. Player’s are encouraged to maintain a personal access code and to use the keypad to recall player statistics. Player statistics record mileage, win-to-loss ratio and high scores. As soon as the personal access code is entered, the stored player name and information is instantly recalled and displayed onscreen.
STARTING UP. Each time power is switched on or restored to the game machine, the system enters Start-up Tests. A "rug" pattern appears on the CRT screen. When the "rug" pattern ends, the screen shows a CPU Board map. Bad ICs are indicated in red, good ICs are in green. The software revision level is shown at the top of the screen.
A status screen to report on network activity will appear for about ten seconds. This screen is used to verify and troubleshoot connections on an array of cabinets.
The system enters Attract Mode once it passes all power-up tests. The Attract Mode screen will cycle endlessly and display a variety of scenes and sounds from a typical race on any given track. The system does not exit Attract Mode until the desired amount of coins or tokens is inserted and game play commences.
Operations - 9
GAME RULES AND OBJECTIVES The game is configured for one-player game play, but up to four cabinets may be linked at one time to promote multiple player competition. To enter Game Mode, individual player(s) must insert the required amount of currency or tokens, press the Start button, and select a car and track. The main objective of the game is to earn top ranking against other drivers.
PLAYER CONTROLS @ = Start button The start button is used to begin game play or to select certain features before a race.
@ Radio button The radio button allows the player to turn radio sounds on and off, and to change stations.
@ Lo button This button shows the view from the driver’s seat inside the vehicle. This is a normal driver view.
# Cam button This button shows the view from directly above. The player can see the front end of the vehicle.
@ Hi button This button shows an aerial view of the vehicle. This is what a helicopter camera would see.
@ Pedals The gas and brake pedals control vehicle speed. Press the gas pedal twice to create a power boost.
@ Seat Position Adjuster The seat position may be changed at any time, even during competition. Pull the adjustment lever to the left while seated then slide the seat forward or backward. Release the lever to lock the seat into position.
Player Control Locations
Operations - 10
GAME OPERATION Access to the menu system for statistics, adjustments, and testing is secured by a keyed lock to prevent tampering. When the menu system is entered, on screen messages guide the operator through tasks.
Cabinet Switches o
o The ON/OFF SWITCH is located on the top side of the cabinet.
The REMOTE MONITOR ADJUSTMENTS are located inside the coin vault. Adjust video image size, brightness, contrast, etc. using the Monitor Test screens and the monitor controls.
The SLAM TILT SWITCH detects forceful vibrations against the coin door to eliminate pounding for free games. It is located on the inside of the coin door opening near the lock.
Control Buttons o The TEST BUTTON accesses the game Menu System. Press the Test button to access the Main Menu and select individual diagnostics, audits, utilities, etc.
The VOLUME UP BUTTON scrolls through menu selections or adjustment items and raises the sound level in game play. An audible tone accompanies each activation of this button.
The VOLUME DOWN BUTTON scrolls through the menu selections or adjustment items and lowers the sound level in game play. An audible tone accompanies each activation of this button.
The SERVICE CREDIT BUTTON allots credits without affecting the game's bookkeeping total. This button can also be used to exit from menu selections or to return to the main menu.
Coin Door Switch Location
Operations - 11
NOTES
Operations - 12
CRUIS’N EXOTICA.
SECTION TWO
ADJUSTMENT, DIAGNOSTIC & AUDIT
MENUS
MENU SYSTEM
WHAT IS THE MENU SYSTEM? The game’s Menu System is a series of auditing, game adjustments and diagnostic screens. You can easily access and apply these screens to optimize game performance. For instance...
» Use game audit screens to assess game performance. » Use adjustment screens to help you customize game performance. For example, you can restore factory default game settings. You can also calibrate player controls for player accuracy. » Use diagnostic screens to verify proper equipment operation.
ACCESSING THE MENU SYSTEM Open the coin door. Locate and press the TEST MODE switch. The game system will exit game Attract Mode and enter Diagnostic Mode. The system runs a brief self-test, and then displays the Main Menu. The Main Menu is the opening screen of the Menu System.
Game audits, adjustments and diagnostics are line items on the Main Menu. Selecting an item opens its submenu. Every submenu presents various options that you may act upon.
CRUIS’N EXOTICA DIAGNOSTICS
MAIN MENU DIAGNOSTIC MENU VERSION INFORMATION GAME AUDITS VERSION: ADJUSTMENT MENU DATE:
UTILITIES BUILD:
CALIBRATE CONTROLS SERIAL: ADJUST VOLUME CHIP DATE: EXIT
PRESS VOLUME UP/DOWN BUTTONS TO SELECT PRESS TEST BUTTON TO ACTIVATE PRESS SERVICE CREDIT BUTTON TO EXIT Typical Main Menu Screen
MENU LAYOUT Observe that each menu screen basically uses the same layout. The game ID, Serial Number, and Date of Manufacture will appear on most of the menu screens. These numbers will be helpful to factory personnel when referring to your game for parts or service.
» The block at the top of each screen displays the current menu title. » Data, such as menu items and video reports, etc., appears in the center of the screen. » Messages, for example explanations and active control functions, etc., appear at the bottom of the screen.
MENU NAVIGATION TOOLS Use the operator control buttons located inside the coin door to navigate menus. Press the Volume Up or Volume Down buttons to scroll through the menu options. Notice the options sequentially become highlighted. Press the Test button to select a highlighted option and access the next menu level. Press the Service Credit button to exit from a menu option screen. NOTE: Only one highlighted option can be selected at a time.
To return to play mode, press the Service Credit button while in the Main Menu screen.
Diagnostics - 2
Main Menu, continued Diagnostic Menu
DIAGNOSTIC MENU To verify the condition of the electrical and electronic hardware in the game, select DIAGNOSTIC MENU at the Main Menu. Diagnostic tests assist you in checking and adjusting the game’s major systems. It is
Use the Volume Up or Volume Down button to highlight the desired Diagnostic Menu option and press the Test button to enter. Use the Service Credit button at any time to exit the Diagnostics and return to the Main Menu. NOTE: The Burn-in Test cannot be halted from the menus.
DIAGNOSTIC MENU SWITCH TEST MOTION TEST DIP SWITCH TEST CPU BOARD TEST SOUND BOARD TEST LINKING TEST STEERING WHEEL TEST MONITOR TEST BURN-IN TEST LAMP TEST LED TEST EXIT TO MAIN MENU
PRESS VOLUME UP/DOWN BUTTONS TO SELECT PRESS TEST BUTTON TO ACTIVATE PRESS SERVICE CREDIT BUTTON TO EXIT
Main Menu Diagnostic Menu, continued Switch Test Menu
SWITCH TEST To verify proper operation of switch and button inputs in the game, select SWITCH TEST at the Main Menu.
SWITCH TEST HIT SERVICE CREDIT TO EXIT POT READING CMOS VALUE MIN CENTER
STEERING WHEEL = XXX XX XXX
GAS PEDAL XX XX BRAKE PEDAL XXX
VIEW 1
VIEW 2 VIEW 3 START COIN 1 LEFT COIN 2 RIGHT TEST COIN 3 CENTER VOLUME UP. COIN 4 RADIO.
SHIFT 1 SHIFT 3 SHIFT 2 SHIFT 4
=
VOLUME DOWN SERVICE CREDIT XX XXX
Diagnostics - 3
Use the Volume Up or Volume Down button to highlight the Switch Test option and press the Test button to access it. Press any switch on the control panel or coin door to cause the corresponding indicator on the screen to illuminate. Each illuminated square represents one completed switch circuit.
Main Menu Diagnostic Menu, continued Motion Test Menu
MOTION TEST To verify functionality of motion seat controls, select MOTION TEST at the Main Menu.
Use the Volume Up or Volume Down button to highlight the Motion Test option and press the Test button to access it. Use the Service Credit button at any time to exit the Motion Test and return to the Main Menu.
MOTION TEST HOME POSITION TILT LEFT TILT RIGHT TILT FORWARD TILT BACK MULTIPLE COMMANDS.
PRESS VOLUME UP/DOWN BUTTONS TO SELECT PRESS SERVICE CREDIT BUTTON TO EXIT
HOME POSITION. The Home Position routine automatically centers the motion seat so that it is positioned upright and does not tilt at any angle.
TILT LEFT. The Tilt Left routine automatically tilts the motion seat at a left leaning angle.
TILT RIGHT. The Tilt Right routine automatically tilts the motion seat at a right leaning angle.
TILT FORWARD. The Tilt Forward routine automatically tilts the motion seat at a forward leaning angle.
TILT BACK. The Tilt Back routine automatically tilts the motion seat at a backward leaning angle.
MULTIPLE COMMANDS. The Multiple Commands routine automatically cycles through and performs each of the other routines. Press the Service Credit button to stop the cycle and return to the Motion Test Menu
Main Menu Diagnostic Menu, continued DIP Switch Test
DIP SWITCH TEST To verify the functionality of both 8-position DIP switches on the CPU Board, select DIP SWITCH TEST at the Main Menu. Observe immediate on-screen results by changing the setting on a switch.
Use the Volume Up or Volume Down button to highlight the DIP Switch Test option and press the Test button to access it. The current settings appear on-screen. Consult the table on the next page to determine if changes are required. The default switch positions are all OFF for standard operation.
A vertical bar next to the switch position column indicates a common switch function.
Diagnostics - 4
DIP SWITCH TEST DIP SW 1 1 OFF KIT OFF 2 OFF MOTION OFF 3 OFF UPRIGHT CABINET 4 ON WHEEL INVERT ON
OFF UNUSED OFF LINK DISABLED OFF OFF
DIP Sw2 OFF OFF OFF | USA1 OFF | 3 COINS/1 CREDIT lag OFF
OFF
PRESS SERVICE CREDIT BUTTON TO EXIT
Function swi1 Sw2 SW3 SW4 SW5 SW6 SW7 SW8 Dedicated * OFF
Kit ON
Motion Disabled OFF Motion Enabled ON Stand Up Style Cabinet OFF Sit Down Style Cabinet ON Wheel Invert Disabled OFF Wheel Invert Enabled ON Unused OFF ON Link Disabled OFF Link Enabled ON Linking I.D. Number Master (Game Number 1) OFF | OFF Slave (Game Number 2) ON | OFF Slave (Game Number 3) OFF | ON Slave (Game Number 4) ON ON Setting Table for DIP Switch 1
- DIP 1, Switch 1 must be set to the OFF position in order for proper operation.
Game Adjustments for Linked Operation To avoid confusion, we recommend that all adjustments be set to identical values before Video Game Machines (VGMs) are linked. VGMs might operate incorrectly if this is not the case, with the following exceptions:
- Linked VGMs must all have compatible software versions. Newer versions may contain instructions that previous versions do not have, causing them to halt or reset at random. On-screen messages will indicate that different versions are in use when the linking feature is enabled for each.
Diagnostics - 5
2. The graphic effects and added attractions for the slave cabinets must be the same as the master. All games must have these features enabled or all must have them disabled. Mixed settings, for example road kill or a show girls setting, can cause games to become unsynchronized during competition and lead to incorrect final results (i.e., two first place finishes with different times, collisions with unseen objects, etc.).
The linking feature overrides some of the individual software settings. For instance, the master (VGM #1) sets and controls the difficulty level for all linked slaves. The difficulty level reported by the slave games may not match the setting of the master game.
The linked game with the highest ranking determines software settings. Adjustments such as bonus times will be controlled by the games in decreasing identification order. For example, if four games are linked, slave game #3 will always override game #4 but have no effect on games #1 or #2. This permits games to have different standards to help equalize players with different skill levels.
The linking cables attach to a connector on a metal bracket located under the CPU Board Assembly at the rear of the cabinet. Unlock and remove the cabinet rear door for linking access.
Notes on Linking: 1. For a 2-way link, the leftmost VGM is the master (#1); the second VGM is slave #2. One linking cable is required.
For a 3-way link, the left VGM is the master (#1); the center and right VGMs are slaves #2 and #3. Two cables are required.
For a 4-way link, the leftmost VGM is the master (#1); the left center VGM is slave #2, right center machine is #3, and the right most machine is slave #4. Three linking cables are required.
The linking feature will not function if the master is not turned on and in normal game play mode. If the master is turned off, disconnected from the linking cable, or in any other mode of operation (offline, diagnostics, etc.), none of the slaves will be able to link.
The linking feature will function for all other VGMs if one of the slaves is not turned on and in normal game play mode. If any slave is turned off, disconnected from the linking cable, or in any other mode of operation (offline, diagnostics, etc.), the linking ability of other slaves will not be affected.
The linking feature will function for some VGMs, and not others, if all of the link activity switches are not enabled or the software version numbers are not the same. The master game will not recognize other games with disabled linking or different link identification numbers.
DIP SWITCH SETTING FOR COINAGE There are many ways to select the type and quantity of currency recognized by the game machine.
1. The most common coin combinations for several countries are pre-programmed and may be selected from the table when Standard Pricing is activated (see Game Adjustments).
DIP Switch settings may be changed with the power switched on. Set any switch and then observe the screen to verify that the desired selection is enabled. NOTE: If CMOS Coin Settings are active, switch settings for an individual Country will have no effect.
Some European countries may accept currency used in other countries. The most popular coinage settings are listed beneath ‘Other’ in the Standard Pricing Table.
Alternate settings are listed beneath ‘General’ in the Standard Pricing Table.
Default settings are denoted by an (*). Switches 1 through 5 select country codes. Switches 6 and 7 are used to select one of four modes for each country.
Diagnostics - 6
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
Main Menu Diagnostic Menu, continued CPU Board Test
CPU BOARD TEST To verify proper operation of the memory circuits, select CPU Board Test at the Main Menu. This test checks the memory circuits in a manner similar to the Start-Up Test. A “rug” pattern representing the layout of the RAM and ROM circuits on the CPU Board will appear on-screen while the video circuits are tested.
Typical Rug Pattern
Use the Volume Up or Volume Down buttons to highlight CPU Board Test and press the Test button. The memory circuits are shown as gray with a white outline. During the test, ICs are good if they turn green; they are faulty if they turn red. The game automatically returns to the Diagnostic Menu after the test is completed.
Main Menu Diagnostic Menu, continued Sound Board Test
SOUND BOARD TEST To verify proper operation of the sound components, select Sound Board Test at the Main Menu. This test allows you to access and listen to the sounds used in the game.
UP TO CHANGE MUSIC DOWN TO TRIGGER SOUND EFFECTS SERVICE CREDIT TO EXIT
INE SPEED LOOP
SOUND EFFECT GIRL SPEECH
Use the Volume Up or Volume Down button to highlight the Sound Board Test option and press the Test button. Press Service Credit to return to the Diagnostic Menu when finished. Diagnostics - 8
Press Volume Up to activate the tune selection and each additional push of the switch automatically selects and plays the next tune. Pressing the Volume Down button will trigger a sound effect and each additional push selects and plays the next sound effect.
Main Menu Diagnostic Menu, continued Linking Test
LINKING TEST To verify communications between the game machine and others connected to it, select Linking Test at the Main Menu.
MACHINE 1 MASTER ACTIVE MACHINE 2 SLAVE ACTIVE MACHINE 3 SLAVE ACTIVE MACHINE 4 SLAVE ACTIVE
TOTAL TRANSMISSIONS =X TOTAL ERRORS. Xx
LINK ENABLED LINKED GAME NUMBER: X
PRESS TEST TO CLEAR ERRORS. PRESS SERVICE CREDITS BUTTON TO EXIT
Use the Volume Up or Volume Down button to highlight Linking Test and press the Test button. This test runs automatically and will display results on-screen.
Press the Service Credit button to clear errors and restart the test cycle. Press the Test button to exit from this menu screen.
Main Menu Diagnostic Menu, continued Steering Wheel Test
STEERING WHEEL TEST To verify the proper directional movement of the steering wheel, select Steering Wheel Test at the Main Menu. Make sure hands and other objects are clear of the steering wheel when this test is selected because the steering wheel will automatically rotate to the left. Follow the on-screen instructions.
STEERING WHEEL TEST TURN WHEEL LEFT PRESS TEST TO CONTINUE
TURN WHEEL RIGHT PRESS TEST TO CONTINUE
Use the Volume Up or Volume Down button to highlight the Steering Wheel Test and then press the Test button. The steering wheel immediately turns to the left. Press the Test button a second time and the wheel turns to the right and will automatically return to the Diagnostic Menu.
Diagnostics - 9
Main Menu Diagnostic Menu, continued Monitor Test
MONITOR TEST To verify color clarity of the monitor, select Monitor Test at the Main Menu.
Use the Volume Up or Volume Down button to highlight the desired monitor test and press the Test button. Repeatedly press the Test button to cycle through test screens and automatically return to the Main Menu. Watch for the following results on-screen during this test.
COLOR BARS. Observe 4 color bars in different shades appear on-screen as aids in adjusting the green, blue, and red color levels. Each color should appear sharp and clear. Check video brightness and contrast.
The CROSSHATCH PATTERNS test fills the screen with a series of dots within a grid. Observe the dots are perfectly round and that both the grid and dots are clear. Inspect monitor convergence, linearity, and screen size.
If any of the tests show a need for CRT adjustment, use the proper knobs on the Monitor Controls board.
Main Menu Diagnostic Menu, continued Burn-In Test
BURN-IN TEST To properly diagnose intermittent CPU problems, select Burn-in Test at the Main Menu. This test cycles non-stop through the CPU Board Test. A “rug” pattern representing the layout of the RAM and ROM circuits on the CPU Board will appear on-screen while the video circuits are tested.
("|
Typical Burn-in Test Rug Pattern
Use the Volume Up or Down Switch to highlight the Burn-in Test and press the Test button to activate. The Burn-in Test will stop and display an error message on-screen if an error is detected.
Inputs from the control buttons are ignored during Burn-in. The Burn-in Test cannot be halted from the menus, you must switch the power to the game machine off and then switch it back on.
Diagnostics - 10
Main Menu Diagnostic Menu, continued Lamp Test
LAMP TEST To detect intermittent or faulty incandescent bulbs, select Lamp Test at the Main Menu. This test ensures that the incandescent bulbs critical to game operation function properly.
Use the Volume Up or Volume Down button to highlight Lamp Test and press the Test button. During the test observe the selected lamp(s) switches turn on or off when the corresponding selection is made.
LAMP TEST TURN ON ALL LAMPS TURN OFF ALL LAMPS TURN ON START
TURN ON VIEW 1
TURN ON VIEW 2 TURN ON VIEW 3 TURN ON MARQUEE LAMP 1 TURN ON MARQUEE LAMP 2
PRESS VOLUME UP/DOWN TO SELECT PRESS TEST BUTTON TO ACTIVATE PRESS SERVICE CREDIT BUTTON TO EXIT
NOTES ON THE LAMP TEST:
- The RADIO button is not illuminated and requires no lamp test.
- The MARQUEE LAMPS are located inside the lighted header as part of the Deluxe Linking Kit.
- To override individual tests select either TURN ON or TURN OFF ALL LAMPS. The lamps also automatically switch off when the SERVICE CREDIT button is pressed to exit this screen.
Press the Service Credit button to return to the Diagnostic Menu.
Main Menu Diagnostic Menu, continued LED Test
LED TEST To verify that the Dashboard LED’s function properly, select LED Test at the Main Menu. This test allows you to control and test the illumination of the LED’s located on the dash PCB.
Use the Volume Up or Volume Down button to highlight the LED Test and press the Test button. This test detects intermittent or faulty LED’s that are critical to game operation. Observe the following activity on the dash PCB.
LEDS ON LEDS OFF LEDS CYCLE
PRESS VOLUME UP/DOWN TO SELECT PRESS TEST BUTTON TO ACTIVATE PRESS SERVICE CREDIT BUTTON TO EXIT
LED’s ON. This option simultaneously turns on all LED’s. LED’s remain illuminated until switched off.
LED’s OFF. This option simultaneously turns off all LED’s. LED’s will not be illuminated during this phase.
LED’s CYCLE. This option causes the LED’s to cycle sequentially turns LED’s on and off beginning with those located on the far left-hand side of the dash PCB. To stop the cycle press the Service Credit button. Diagnostics - 11
Main Menu Game Audits
GAME AUDITS Press the Volume Up or Volume Down button to highlight Game Audits in the Main Menu and press the Test button. To move between pages of the Game Audit Table, press the Volume Up or Volume Down button. Press the Service Credit button to return to the Main Menu from this screen.
The Game Audits Table displays the play statistics. The left side of the table names the Audit item; the right side shows the amount of play. Record these statistics before any service or repairs are done.
GAME AUDITS
COIN AUDITS, PAGE 1
COIN 1 LEFT COIN 2 RIGHT COIN 3 CENTER COIN 4 BILL SERVICE CREDITS
TOTAL STARTS TOTAL CONTINUES TOTAL GAMES
TOTAL FREE RACES FREE GAMES PERCENT EXPIRED RACES
PRESS VOLUME UP/DOWN FOR NEXT PAGE PRESS SERVICE CREDIT BUTTON TO EXIT Typical Audit Table, page 1
GAME AUDITS
MISC. AUDITS, PAGE 2
POWER-ON TIME SECONDS. GAME TIME SECONDS AVERAGE GAME TIME SECONDS KEYPAD LOG-INS
EVENT U-GAMES WATCHDOG(S) BURN-IN LOOPS
PRESS VOLUME UP/DOWN FOR NEXT PAGE PRESS SERVICE CREDIT BUTTON TO EXIT
Audit Table, page 2
Diagnostics - 12
€L - sonsoubeiq vy e6ed ‘alge. pny 4LIX3 OL NOLLNG LIGSHDS SDIAYSS SSAYd 39Vd LXAN 4YOS NMOQ/dN AWNIOA SS3¥d SOAS AWIL € WV SOAS AWIL 2 WV SOAS SWIL | WW SLNONIdS: SdWAP MOL @ad33d NYHOH S3ITaSHM sgor LNIVd WOLSND GaL037aS IWANVW Q3LO3TAS OILVWOLNV y JOVd ‘SLO3IS43 WI0adS SLIGAV SWV9 bed ‘alge pny 4LIX3 OL NOLLNG LIGSHS SDIAYSS SSAYd 39Vd LXAN ¥YOS NMOQ/dN SAWNIOA SS3¥d Iwas: aTOsnNW YadIA dvo Lar x x << YVvO ATON Adil ONVLSNW HSVN
x x x x YSWAWNH ALLA Ya 1MOdd daar <>< <>< € AOVd ‘GSLOIISS STOIHSA SLIGNV AWVD penuljuoo ‘syipny owed nue; ueW
Main Menu Game Audits, continued
GAME AUDITS
INDIVIDUAL TRACK SELECTED, PAGE 5
VEGAS KOREA ALASKA ATLANTIS HONG KONG INDIA. SAHARA HOLLAND IRELAND AMAZON TIBET MARS KX KOK OK KOK OK KOKO
PRESS VOLUME UP/DOWN FOR NEXT PAGE PRESS SERVICE CREDIT BUTTON TO EXIT Audit Table, page 5
GAME AUDITS
CRUIS’N EXOTICA STARTS, PAGE 6
VEGAS KOREA ALASKA ATLANTIS HONG KONG INDIA SAHARA HOLLAND IRELAND AMAZON TIBET MARS KKK KK OK OK OK OK OK
PRESS VOLUME UP/DOWN FOR NEXT PAGE PRESS SERVICE CREDIT BUTTON TO EXIT Audit Table, page 6
Diagnostics - 14
Main Menu Game Audits, continued
GAME AUDITS TRACK WINS, PAGE 7 VEGAS KOREA ALASKA ATLANTIS HONG KONG INDIA SAHARA HOLLAND IRELAND AMAZON TIBET MARS KK KK OK OK KOKO OK
PRESS VOLUME UP/DOWN FOR NEXT PAGE PRESS SERVICE CREDIT BUTTON TO EXIT
Audit Table, page 7
GAME AUDITS DRIVER SELECTION, PAGE 8 JEN JASON CLOWN RETRO DUDE ASIAN BABY AFM COWBOY ALIEN XK OK KK OK OK KOK
PRESS VOLUME UP/DOWN FOR NEXT PAGE PRESS SERVICE CREDIT BUTTON TO EXIT
Audit Table, page 8
GAME AUDITS BIG HEAD DRIVER SELECTION, PAGE 9
JEN BIGHEAD JASON BIGHEAD CLOWN BIGHEAD RETRO BIGHEAD DUDE BIGHEAD ASIAN BIGHEAD BABY BIGHEAD AFM BIGHEAD COWBOY BIGHEAD ALIEN BIGHEAD KX KOK OK KK OK OK
PRESS VOLUME UP/DOWN FOR NEXT PAGE PRESS SERVICE CREDIT BUTTON TO EXIT Audit Table, page 9
Diagnostics - 15
Main Menu Adjustment Menu
ADJUSTMENT MENU To optimize game performance and earnings or to change the look or sound of the game, select the Adjustment Menu at the Main Menu. The Attract Mode features, Game Pricing and Game Difficulty may also be customized. Free races may be awarded to encourage players. Free game player incentives may reduce earnings. NOTE: Individual Game Adjustments are explained in more detail on the following pages.
Press the Volume Up or Volume Down button to highlight the desired Adjustments Menu option on the Main Menu and press the Test button. Use these screens to optimize game performance and earnings.
The Adjustments Menu offers several options. Press the Volume Up or Volume Down button to highlight an option and press the Test button. Each time an option on the menu is activated you are provided with multiple setting choices. Use the Volume Up or Volume Down button to change the current value setting and observe a confirmation box as shown below appears.
SELECT THIS PRICING? ARE YOU SURE? YES TEST TO ACCEPT UP TO INCREASE DOWN TO DECREASE Typical Confirmation box
Press the Volume Up or Volume Down button to select YES or NO, then press the Test button to lock in the setting. Selecting NO cancels any changes values and returns the previous values to memory.
ADJUSTMENT MENU
STANDARD PRICING --USA 1 ON CUSTOM PRICING OFF FREE PLAY OFF FIRST PLACE GETS FREE RACE ON START TIME BONUS SECS 75 CHECKPOINT BONUS TIME SECS 20 ATTRACT MODE SOUNDS INITIAL ENTRY ON MINIMUM VOLUME LEVEL 1 STEERING WHEEL POWER 5 SPEED IN MPH OR KPH KEYPAD ACTIVE MANUAL TRANS DISABLED SHOW ROADKILL SHOW ENDING SHOW GIRLS HIGH SCORE RESET GAME DIFFICULTY MAXIMUM CREDITS MULTI PLAYER FREE RACES
PRESS VOLUME UP/DOWN TO SELECT PRESS TEST BUTTON TO ACTIVATE PRESS SERVICE CREDIT BUTTON TO EXIT
Diagnostics - 16
Main Menu Game Adjustments, continued Standard Pricing
Use the Standard Pricing Table illustrated below as a guide to select the desired coin credit setting(s) for your game machine.
| NAME | START | CONTINUE | CREDITS/COIN | COINT | COIN2 | COINS | COINS | BILL | |||||
| ANTILLES: | 2 | 2 | 17256, 4G | 25¢ | 1G | |||
| AUSTRALIA 1 | 2 | 2 | 173X206, 2/81.00 | 20¢ | $1.00 | |||
| AUSTRALIA 2 | 2 | 2 | 1/5X206, 1/$1.00 | 20¢ | $1.00 | |||
| AUSTRIA 1 | 2 | 2 | 1/5Sch, 2/10Sch | 5Sch | 10Sch | ||||
| AUSTRIA 2 | 2 | 2 | 1/2X5Sch, 3/2X10Sch | 5Sch__| | 10Sch | |||
| BELGIUM 1 | 2 | 2 | 1/20BF | 20BF | 20BF | |||
| BELGIUM 2 | 2 | 2 | 3/20BF | 20BF | 20BF | |||
| BELGIUM 3 | 2 | 2 | 2/20BF | 20BF | 20BF | |||
| BELGIUMECA | 2 | 2 | 1/20BF | 50BF. | 20BF | SBF | ||
| CANADA 1 | 2 | 2 | 172x256, 3/$1 | 25¢ | 25¢ | |||
| CANADA 2 | 2 | 2 | 1/2x 25¢, 3/$1 | 25¢ | $1.00 | |||
| CANADA 3 | 2 | 2 | 3/ $1.00, 6 / $2.00 | $1.00 | $2.00 | ||||
| CANADA ECA | 2 | 2 | 1/2x 25¢, 3/$1 | 25¢ | $1.00 _| $2.00 | |||
| DENMARK | 2 | 2 | 3/SDKr, 7/10DKr | ‘SDKr | TODKr, | |||
| FINLAND | 2 | 2 | TiFmk | Temk | Semk | ||||
| FRANCE 1 | 2 | 2 | 215Fr, SOFT | Fr | 10Fr | |||
| FRANCE 2 | 2 | 1 | 2I5Fr, 4/10Fr | SFr | 10Fr | |||
| FRANCE 3 | 2 | 1 | 1/5Fr, 3/10Fr | 5Fr | 10Fr | |||
| FRANCE 4 | 2 | 4 | 1/5Fr, 2/10Fr | SFr | 10Fr | |||
| FRANCE 5 | 2 | 1 | 2/5Fr, S/10Fr, 11/2 X 10Fr | SFr | 10Fr | |||
| FRANCE 6 | 2 | 1 | 2I5Fr, 4/10F tr, 9/2 X 10Fr | SFr | 10Fr | |||
| FRANCE 7 | 2 | 1 | 1/5Fr, 3/10Fr, 7/2 X 10Fr | 5Fr | 10Fr | |||
| FRANCE 8 | 2 | 1 | 1/5Fr, 2/10F r, 5/2 X 10Fr | SFr | 10Fr | |||
| FRANCE 9 | 2 | 4 | 1/3 X 1Fr, 2/5Fr | 1Fr | SFr | |||
| FRANCE 10 | 2 | 1 | 1/2 X 1Fr, 3/5Fr | 1Fr | SFr | |||
| FRANCE 11 | 2 | 1 | 1/3 X 1 Fr, 2/5F r, 5/2 X SFr | 1Fr | SFr | |||
| FRANCE 12 | 2 | 1 | 1/2 X 1Fr, 3/5Fr, 7/2 X SFr | 1 | 5Fr | |||
| FRANCE ECA 1 | 1 | 1 | 215Fr, S/10Fr | Fr | SFr | 70Fr | 20Fr | |
| FRANCE ECA 2 | 1 | 4 | 215Fr, 4/10Fr | 1Fr | SFr | 10Fr | 20Fr | |
| FRANCE ECA 3 | 1 | 1 | 1/5Fr, 3/10Fr | 1Fr | SFr | 10Fr | 20Fr | |
| FRANCE ECA 4 | 1 | 1 | 1/5Fr, 2/10Fr | 1Fr | SFr | 10Fr | 20Fr | |
| FRANCE ECA 5 | 1 | 1 | 2I5Fr, S/10Fr, 11/2 X 10Fr | 1Fr | SFr | 10Fr | 20Fr | |
| FRANCE ECA 6 | 1 | 1 | 2I5Fr, 4/10Fr, 9/2 X 10Fr | 1Fr | SFr | 10Fr | 20Fr | |
| FRANCE ECA 7 | 1 | 4 | 41/5Fr, 3/10Fr, 7/2 X 10Fr | 1Fr | SFr | 10Fr | 20Fr | |
| FRANCE ECA 8 | 1 | 1 | 1/5Fr, 2/10Fr, 5/2 X 10Fr | 1Fr | SFr | 10Fr | 20Fr | |
| FRANCE ECA 9 | 1 | 1 | 1/3 X 1Fr, 2/5Fr | 1Fr | SFr | 10Fr | 20Fr | |
| FRANCE ECA 10 | 1 | 1 | 1/2 X 1Fr, 3/5Fr | 1Fr | SFr | 10Fr | 20Fr | ||
| FRANCE ECA 11 | 1 | 4 | 1/8 X 1 Fr, 2/5Fr, 5/10Fr | 1Fr | SFr | 10Fr | 20Fr | |
| FRANCE ECA 12 | 1 | 1 | 1/2 X Fr, 3/5Fr, 7/10Fr | 1Fr | SFr | 10Fr | 20Fr | ||
| FRANCE ECA13 | 1 | 1 | 1/1 0Fr, 2/20Fr, 4/30Fr | 1Fr | 5Fr | 10Fr | 20Fr | ||
| FREE PLAY | = | = | = | None | None | None | None | None |
| GERMANY 1 | 2 | 2 | 771M, 6/5DM | 7DM | SDM | |||
| GERMANY 2 | 2 | 1 | 1/1DM, 7/5DM | 1DM | 5DM | |||
| GERMANY 3 | 2 | 1 | 1/1DM, 8/5DM | 1DM | 5DM | |||
| GERMANY 4 | 2 | 4 | 1/1DM, 5/5DM | 1DM | 5DM | |||
| GERMANY 5 | 2 | 1 | 1/1DM, 6/5DM | 1DM | 5DM | |||
| GERMANY ECA1 | 2 | 2 | 1/1DM, 2/2DM, 6/SDM | 1DM | 20M | 5DM | |||
| GERMANY ECA2 | 2 | 1 | 1/1DM, 2/2DM, 6/SDM | 1DM | 20M | 5DM | |||
| GERMANY ECA3_| | 1 | 1 | 1/1DM, 2/2DM, 6/SDM | 1DM | 20M. | 5DM. | ||
| HUNGARY, | 2 | 2 | T2X10Ft, S/2X20Ft | TOFt | 20Ft | |||
| TTALY | 2 | 2 | T7/S500LIt | S00L | SOOLIt | ||||
| ‘JAPAN 1 | 2 | 2 | 1/100Yen' | 100 | 100 |
Yen Yen
| JAPAN 2 | 2 | 2 | 2i00Yen | 100 | 100 |
Yen Yen
| JAPAN 3 | 1 | 1 | 100Yen | 100 | 100 |
| JAPAN 4 | 1 | 1 | 2/100Yen | 100 | 100 |
| JAPAN 5 | 1 | 1 | 4/100Yen | 100 | 100 |
| JAPAN 6 | 1 | 1 | 1/2X100Yen | 100 | 100 |
| NETHERLANDS | 2 | 2 | THFI, 3/2.5HFI | THF | 2.5HFI |
| NEW ZEALAND? | 7 | 1 | 17§1 | $1 | $2 | |
| NEW ZEALAND 2 | 1 | 1 | 2181 | $1 | $2 | |
| NORWAY. | 2 | 2 | /SNKr, 6/10NKr | ‘SNKr | 10NKr, |
| ‘SPAIN 7 | 2 | 2 | 77100Pta, 6/500Pta | T00Pta_| | 500PIa |
| SPAIN 2 | 2 | 2 | 1/100Pta, 5/500Pta | 100Pta_| | 500Pta |
| ‘SWEDEN | 2 | 2 | T3X18Kr, 2/5SKr | 1SKr | SSKr |
| SWITZERLAND1 | 2 | 2 | 1/1SFr, 6/5SFr | 1SFr | SSFr | |
| SWITZERLAND 2 | 2 | 2 | 1/1 SFr, 7/5SFr | 1SFr | 5SFr | |
| SWITZERLAND 3__| | 2 | 2 | ASFr, 8/5SFr | 1SFr | 5SFr |
Diagnostics - 17
Main Menu Game Adjustments, continued Standard Pricing, continued
| NAME | ‘START | CONTINUE | CREDITS/COIN | COIN 1 | COIN 2 | COINS | COIN4 | BILL | |
| UK ECA 1 | 1 | 1 | 1/50p, 3/£1.00 | £1.00 | 50p | 20p | 10p | £2.00 |
| UK ECA2 | 1 | 1 | 1/50p, 2/£1.00 | £1.00 | 50p | 20p | 10p | £2.00 |
| UK ECA3 | 1 | 1 | 1/30p, 2/50p, 5/£1.00 | £1.00 | 50p | 20p | 10p | £2.00 |
| UK4 | 1 | 1 | 1/50p, 3/£1.00 | £1.00 | 50p | |||
| UK5 | 1 | 1 | 1/50p, 2/£1.00 | £1.00 | 50p | |||
| UK ECA6 | 1 | 1 | 1/30p, 2/50p, 4/£1.00 | £1.00 | 50p | 20p | 10p | £2.00 |
| UK ECA7 | 1 | 1 | 3/£1.00 | £1.00 | 50p | 20p | 10p | £2.00 |
| UK ECA8 | 1 | 1 | 1/50p, 2/£1.00, 4/£2.00 | £1.00 | 50p | 20p | 10p | £2.00 |
| USA1 | 2 | 2 | 1/25¢ | 25¢ | 25¢ | $1.00 | ||
| USA2 | 2 | 1 | 1/25¢ | 25¢ | 25¢ | $1.00 | ||
| USA3 | 1 | 1 | 1/25¢ | 25¢ | 25¢ | $1.00 | ||
| USA4 | 1 | 1 | 1/50¢, 3/$1.00 | 25¢ | 25¢ | $1.00 | ||
| USAS | 2 | 1 | 1/50¢, 4/$1.00 | 25¢ | 25¢ | $1.00 | ||
| USA6 | 1 | 1 | 1/50¢ | 25¢ | 25¢ | $1.00 | ||
| USA7 | 1 | 1 | 1/50¢, 3/$1.00 | 25¢ | 25¢ | $1.00 | ||
| USA8 | 2 | 2 | 1/50¢, 4/$1.00 | 25¢ | 25¢ | $1.00 | ||
| USA9 | 3 | bs | 1/25¢, 4/$1.00 | 25¢ | 25¢ | $1.00 | ||
| USA10 | 3 | 3 | 1/25¢, 4/$1.00 | 25¢ | 25¢ | $1.00 | ||
| USA11 | 4 | Es | 1/25¢, 4/$1.00 | 25¢ | 25¢ | $1.00 | ||
| USA12 | 4 | 3 | 1/25¢, 4/$1.00 | 25¢ | 25¢ | $1.00 | ||
| USA13 | 4 | 4 | 1/25¢, 4/$1.00 | 25¢ | 25¢ | $1.00 | ||
| USA ECA | 3 | 3 | 1/25¢, 4/$1.00 | $1.00 | 25¢ | 10¢ | 05¢ | $1.00 |
Main Menu Game Adjustments, continued Custom Pricing
Use the custom Pricing Menu to specify pricing settings other than the ones listed in the Standard Pricing Table. Custom Pricing can also be used to select the amount of credits required to start a game and the amount of credits required to continue a game. This option is adjusted from the Dip Switch Settings.
CUSTOM PRICING MENU
LEFT CHUTE UNITS RIGHT CHUTE UNITS CENTER CHUTE UNITS FOURTH CHUTE UNITS BILL CHUTE UNITS UNITS PER CREDIT UNITS FOR BONUS MINIMUM UNITS CREDITS TO START CREDITS TO CONTINUE LEFT CHUTE COUNTER RIGHT CHUTE COUNTER CENTER CHUTE COUNTER FOURTH CHUTE COUNTER BILL CHUTE COUNTER SHOW FRACTIONS SELECT CUSTOMER PRICING EXIT TO MAIN MENU XK KOK KK OK OK OK OK OK OK OK OKO
Sn of
PRESS VOLUME UP/DOWN TO SELECT PRESS TEST BUTTON TO ACTIVATE PRESS SERVICE CREDIT BUTTON TO EXIT
Diagnostics - 18
The following table clarifies Pricing Menu terms...
SCREEN TERM DEFINITION Chute Units Currency inserted accumulates units. This adjustment specifies the quantity of units given for each coin or bill in each coin chute. Units Per Credit Units needed to accumulate a credit. Units For Bonus Units awarded after a player has accumulated enough points for a bonus. Minimum Units No credits will be awarded until the minimum required currency units have been accumulated. Credits to Start Units needed to enter game play. Credits to Continue Units needed to continue game play. Chute Counter Total number of units accepted by a chute. Show Fractions Fractional credits are observable on the credit screen when YES is selected. Select Customer Pricing Selecting YES enables custom pricing and overrides default settings.
Main Menu Game Adjustments, continued
To further optimize game performance and earnings, select any one of the options on the Adjustments Menu. Press the Volume Up or Volume Down button to highlight an option and press the Test button.
Each time an option on the menu is activated you are provided with multiple setting choices. Use the Volume Up or Volume Down button to change the current value setting and observe a confirmation box as shown below appears.
SELECT THIS PRICING ARE YOU SUR YES TEST TO ACCEPT UP TO INCREASE DOWN TO DECREASE Typical Confirmation box
Press the Volume Up or Volume Down button to select YES or NO, then press the Test button to lock in the setting. Selecting NO cancels any changes values and returns the previous values to memory.
Main Menu Game Adjustments, continued Free Play Menu
Free Play This option selects free play. The setting choices for this adjustment are: -ON -OFF -Factory Setting: | OFF
Main Menu Game Adjustments, continued First Place Awards Free Game Menu
First Place Awards Free Game Awards a player a free game on first place finish. The setting choices for this adjustment are: -ON -OFF -Factory Setting: ON
Diagnostics - 19
Main Menu Game Adjustments, continued Start Time Bonus Seconds Menu
Start Time Bonus Seconds This determines the initial time a player is given to finish a race. The setting range is: -Maximum: -Minimum: 60 -Factory Setting: 75
Main Menu Game Adjustments, continued Checkpoint Bonus Time Menu
Checkpoint Bonus Time This awards the player a time bonus for passing a checkpoint. The setting range is: -Maximum: 10 -Minimum: 25 -Factory Setting: 20
Main Menu Game Adjustments, continued Attract Mode Sound Menu
Attract Mode Sound This determines if the game will make sounds in the attract mode. The settings for this adjustment are: -ON -OFF -Factory Setting: | OFF
Main Menu Game Adjustments, continued Initial Entry Menu
Initial Entry This determines if the game will allow High Score Entry and Display Table. The setting choices are: -ON -OFF -Factory Setting: ON
Main Menu Game Adjustments, continued Minimum Volume Level Menu
Minimum Volume Level This determines the minimum volume level of the game sounds. The setting range is: -Maximum: 30 -Minimum: 0 -Factory Setting: 11
Diagnostics - 20
Main Menu Game Adjustments, continued Steering Wheel Power Menu
Steering Wheel Power This determines the amount of power provided to steering. The setting choices are: -Maximum: 10 -Minimum: 1 -Factory Setting: 5
Main Menu Game Adjustments, continued Speed in MPH or KPH Menu
Speed in MPH or KPH This determines speedometer setting in miles per hour or kilometers per hour. The setting choices are: -MPH -KPH -Factory Setting: MPH
Main Menu Game Adjustments, continued Manual Trans Disabled Menu
Manual Trans Disabled This provides control of the manual transmission option. The setting choices are: -ON -OFF -Factory Setting: OFF
Main Menu Game Adjustments, continued Keypad Active Menu
Keypad Active This determines whether players’ are allowed to use the keypad for inputs. The setting choices are: -ON -OFF -Factory Setting: ON
Main Menu Game Adjustments, continued Show Road Kill Menu
Show Road Kill This determines if dead animals are shown in the game. The setting choices are: -ON -OFF -Factory Setting: ON
Diagnostics - 21
Main Menu Game Adjustments, continued Show Ending Menu
Show Ending This determines if an image of the President is seen at various points in the game. The setting choices are: -ON -OFF -Factory Setting: ON
Main Menu Game Adjustments, continued Show Girls Menu
Show Girls This determines if "sexy" girls are seen at various points in the game. The setting choices are: -ON -OFF -Factory Setting: ON
Main Menu Game Adjustments, continued High Score Reset Menu
High Score Reset This determines the number of points required to reset the high score. The setting range is: -Maximum: 25000 -Minimum: 1000 -Factory Setting: 5000
Main Menu Game Adjustments, continued Game Difficulty Menu
Game Difficulty This allows the operator to select the difficulty level of the game. The setting range is: -Easiest: 0 -Hardest: 19 -Factory Setting: 5
Main Menu Game Adjustments, continued Maximum Credits Menu
Maximum Credits This allows the operator to select the maximum number of credits alotted. The setting range is: -Minimum: 1 -Maximum: 99 -Factory Setting: 30
Diagnostics - 22
Main Menu Game Adjustments, continued Multi Player Free Races Menu
Multi Player Free Races This determines whether or not multiple players win free races for top scores. The setting range is: -On: -Off: -Factory Setting: Off
Main Menu Utilities
UTILITIES To clear bookkeeping memory and reset factory defaults, select Utilities at the Main Menu. Press the Volume Up or Volume Down button to highlight the Utilities option on the Main Menu, then press the Test button. Press the Service button to return to the Main Menu from this screen.
CLEAR CREDITS CLEAR GAME AUDITS RESET HIGH SCORES DEFAULT ADJUSTMENTS FULL FACTORY RESTORE EXIT TO MAIN MENU
PRESS VOLUME UP/DOWN TO SELECT PRESS TEST BUTTON TO ACTIVATE PRESS SERVICE CREDIT BUTTON TO EXIT Utilities Menu
The Utilities Menu offers several options. Press the Volume Up or Volume Down button to highlight an option, then press the Test button. Each time an option on the menu is activated you are provided with multiple setting choices. Use the Volume Up or Volume Down button to change the current value setting and observe a confirmation box as shown below appears.
CLEAR CREDITS ARE YOU SURE? YES
TEST TO ACCEPT UP TO INCREASE DOWN TO DECREASE Typical Confirmation Box
Press the Volume Up or Volume Down button to select YES or NO, then press the Test button to lock in the setting. Selecting NO cancels any changes values and returns the previous values to memory.
Diagnostics - 23
Main Menu Utilities, continued Clear Credits Menu
Clear Credits Press the Volume Up or Volume Down buttons to highlight the Clear Credits option on the Main Menu, then press the Test button. This returns all credit values to zero and removes credit amounts from memory.
- Yes -No
- Factory Setting: NO
Main Menu Utilities, continued Clear Game Audits Menu
Clear Game Audits Press the Volume Up or Volume Down buttons to highlight the Clear Game Audits option on the Main Menu, then press the Test button. This returns all audit values to zero and removes totals from memory.
- Yes -No
- Factory Setting: NO
Main Menu Utilities, continued Reset High Scores Menu
Reset High Scores Press the Volume Up or Volume Down buttons to highlight the Reset High Scores option on the Main Menu, then press the Test button. This deletes all high scores and removes player identities from memory.
- Yes -No
- Factory Setting: NO
Main Menu Utilities, continued Default Adjustments Menu
Default Adjustments Press the Volume Up or Volume Down buttons to highlight the Default Adjustments option on the Main Menu, then press the Test button. This sets the adjustments back to their original values.
- Yes -No
- Factory Setting: NO
Main Menu Utilities, continued Full Factory Restore Menu
Full Factory Restore Press the Volume Up or Volume Down buttons to highlight the Full Factory Restore option on the Main Menu, then press the Test button. This returns every variable in the game to the original factory settings.
- Yes
- No
- Factory Setting: NO Diagnostics - 24
Main Menu Calibrate Controls
CALIBRATE CONTROLS To calibrate controls for optimum performance, select Calibrate Controls at the Main Menu.
CALIBRATE CONTROLS TURN WHEEL LEFT PRESS THE TEST TO CONTINUE
TURN WHEEL RIGHT PRESS THE TEST TO CONTINUE
PRESS THE GAS PEDAL PRESS THE TEST TO CONTINUE
PRESS THE BRAKE PEDAL PRESS THE TEST TO CONTINUE
Press the Volume Up or Volume Down buttons to highlight the Calibrate Controls option on the Main Menu, then press the Test button. Follow the instructions that appear on-screen.
Main Menu Adjust Volume
ADJUST VOLUME To select a desirable volume level, select Adjust Volume at the Main Menu. Press the Volume Up or Volume Down button to highlight the Adjust Volume option on the Main Menu, then press the Test button. Remember that the minimum sound level is set under Game Adjustments.
Press the Volume Up button to increase, or the Volume Down button to decrease the sound level of the game. Press the Test button to lock the volume level at the selected value and return to the Main Menu.
ADJUST VOLUME
MIN MAX
TEST EXIT VOL UP INCREASE VOLUME VOLDN DECREASE VOLUME Adjust Volume Screen
Diagnostics - 25
NOTES
Diagnostics - 26
CRUIS’N EXOTICA.
SECTION THREE
SERVICE
SAFETY INSTRUCTIONS The following safety instructions apply to operators and service personnel. Read these instructions before preparing the Video Game Machine (VGM) for play. Other safety instructions appear throughout this manual.
DEFINITIONS OF SAFETY TERMS @ DANGER indicates an imminent hazard. If you fail to avoid this hazard, it WILL cause death or serious injury.
@ WARNING indicates a potential hazard. If you fail to avoid this hazard, it COULD cause death or serious injury.
@ CAUTION indicates a potential hazard. If you fail to avoid this hazard, it MAY cause minor or moderate injury. CAUTION also alerts you about unsafe practices.
@ NOTE indicates information of special importance.
Service - 2
If you or anyone in your family has experienced symptoms linked to an epileptic condition (e.g., seizures or loss of awareness), immediately consult your physician before using any video games.
We recommend that parents observe their children while they play video games. If you or your child experience the following symptoms: dizziness, altered vision, eye or muscle twitching, involuntary movements, loss of awareness, disorientation, or convulsions, DISCONTINUE USE IMMEDIATELY and consult your physician.
CONTENTS OF TYPICAL TOOL PACK
Service - 3
SERVICING Only qualified service personnel should perform maintenance and repairs. The product guidelines apply to all operators and service personnel. Specific notes, cautions, and warnings appear throughout the manual where they apply. We recommend that you read the SAFETY NOTICES section thoroughly before beginning service. NOTE: Always switch off power to the game before servicing.
To service the Marquee... Refer to the Marquee Service illustration. » Switch off the power to the game machine and unplug the AC line cord. » Remove 6 tamper-resistant screws used to fasten the marquee to the top of the cabinet. » Lift the marquee straight out from cabinet and set aside to expose the opening in the cabinet. » Perform the desired repair or equipment replacement. » To re-install, align the contoured marquee with contour of the cabinet. » Fasten in place with the screws provided.
Marquee Service
To service the Fluorescent Light Assembly... Refer to the Marquee Service illustration. » Switch off the power to the game machine and unplug the AC line cord. » Remove the marquee. Refer to service instructions for Marquee. » Reach inside the opening in the cabinet and disconnect the power cable from the fluorescent light assembly. » Loosen, but do not remove the screws fastening the assembly to the cabinet. » Slide the assembly slightly forward to disengage the keyholes. Lift out the assembly.
Service - 4
To service the Fluorescent Lamp or Starter... Refer to the Marquee Service illustration. > VVV Switch off the power to the game machine and unplug the AC line cord. Remove the marquee. Refer to service instructions for Marquee. Reach inside the opening in the cabinet and remove the fluorescent lamp locks. Both the fluorescent tube and the starter require a quarter turn for removal. Grasp the tube or starter, give it a quarter turn and pull it from its socket. Carefully place a new starter or tube into the sockets and rotate it a quarter turn to reinstall. Reinstall both fluorescent lamp locks. Clean the tube to remove fingerprints and dust.
To service the Cabinet Speakers... Refer to the Marquee Service illustration. Speakers are located under the marquee. > > > Switch off the power to the game machine and unplug the AC line cord. Remove the marquee. Refer to service instructions for Marquee. Reach inside the opening in the cabinet and disconnect the wires, including the ground strap. Remove the nuts on the mounting screws before removing the speakers from the enclosure. Perform the desired repair or equipment replacement. Carefully reseat the seals upon completing any task in the speaker enclosure. Reconnect the wires, including ground. Refer to the Cabinet Wiring Diagram for correct speaker polarity.
To service Monitor Bezel.. Refer to the Bezel Service illustration. VVVVVV Switch off the power to the game machine and unplug the AC line cord. Remove the Dashboard. Refer to service instructions for Dashboard. Gently slide the viewing glass up and lift it out of the cabinet to. Set Viewing Glass aside. Grasp the monitor bezel at the bottom and lift it out of cabinet. Perform the desired repair or equipment replacement. Clean both the bezel and the viewing glass before reinstallation.
To service Viewing Glass... Refer to the Bezel Service illustration. > vVVVY Switch off the power to the game machine and unplug the AC line cord. Remove the Dashboard. Refer to service instructions for Dashboard. Gently slide the viewing glass up and lift it out of the cabinet to. Set Viewing Glass aside. Perform the desired repair or equipment replacement. Clean the glass before reinstallation.
Service - 5
Bezel Service
To service the Monitor (CRT)... We recommend that you read the WARNINGS thoroughly before beginning this procedure.
The monitor does not require isolation from the AC line voltage in normal operation. When operating outside the cabinet or servicing the monitor on a test bench, ISOLATE THE MONITOR FROM LINE VOLTAGE WITH AN ISOLATION TRANSFORMER. f WARNING
Vv Switch off the power to the game machine and unplug the AC line cord. Remove the Dashboard, Viewing Glass, and Monitor Bezel. Refer to service instructions for the Dashboard, Viewing Glass and Monitor Bezel. Open the rear cabinet door and disconnect the monitor from the wiring harness and ground wires. Remove 4 nuts securing the monitor mounting flanges to the mounting panel. Pull the monitor carefully from the cabinet and set aside. Perform the desired repair or equipment replacement.
To service the Dashboard... Refer to Dashboard Service illustration. > vVvVV
vvvv Switch off the power to the game machine and unplug the AC line cord. Open the rear cabinet door. Label and disconnect all dash wiring, including the ground strap. Remove the four screws used to fasten the Dashboard to the cabinet. Firmly grab the dash and pull it straight out. NOTE: The Dashboard is heavy, with most of the weight concentrated in the center near the Steering Mechanism. Perform the desired repair or equipment replacement. To re-install, line-up the holes on either side of the Dashboard and push straight back. Check for pinched wires, and then reconnect dash wiring and ground strap. Fasten in place with the screws provided.
Service - 6
Dashboard Service
To service the Center Control Pod.. Refer to Center Control Pod Service illustration. Switch off the power to the game machine and unplug the AC line cord. Remove the Dashboard. Refer to service instructions for Dashboard. Disconnect the light bulbs from the sockets for both the Radio and Start buttons, and set aside. Remove 5 hex head screws that form the outline of the pod and set aside. Lift the Center Control Pod from the Dashboard. Perform the desired repair or equipment replacement. NOTE: It may also be necessary to remove the Dash PCB. Refer to service instructions for Dashboard PCB. Re-install and fasten in place with the screws provided. vVVV
VVV
Vv
_ STEERING MECHANISM SHIFTER POD
by HARNESS
STARTIRADIO BUTTON —/ HARNESS, HARNESS“
44-2041 ‘SOCKET HEAD BOLT BUTTON POD _ HARNESS ~ STEERING WHEEL
DASH PLATE—/
BurronEdD CENTER CONTROL POD. / Lock WASHER -/
Jam nur -/
SPLIT LOCK WASHER, PAS |" STEERING CAP COVER
Center Control Pod Service
Service - 7
To service the Dashboard PCB... Refer to the Dash PCB Service illustration. » Switch off the power to the game machine and unplug the AC line cord. » Remove the Dashboard and the Center Control Pod. Refer to service instructions for the Dashboard and the Center Control Pod. » With the Center Control Pod removed from the dash, remove 5 hex head screws that are used to fasten the PCB to the pod and set aside. Remove the ribbon and power cable connections. Perform the desired repair or equipment replacement. Connect the ribbon and power cable to a Dashboard PCB. NOTE: The red stripe on the ribbon cable must be lined up with pin 1 on the PCB, and the black wire on the power cable must line up with pin 1 on the power connection for the Dashboard. Re-attach the PCB to the pod, and then fasten the pod to the dashboard. Check for pinched wires. Re-install the Dashboard and fasten in place with the screws provided. VVV
VVV
8-32 X 5/16 SCREW SPECIAL DASH PCB ASSEMBLY
DASH LED_/ POWER CABLE MOLDED CENTER ‘CONTROL POD /
X
26 PIN RIBBON CABLE
OVAL PUSH BUTTON START
OVAL PUSH BUTTON RADIO Dash PCB Service
To service the Left or Right Control Pods.. Refer to the Control Pod, Buttons and Shifter Service illustration. Switch off the power to the game machine and unplug the AC line cord. > » Remove the 4 tamper-resistant buttons used to fasten the faceplate. » Pull the plate forward enough to expose the switches. » Label and disconnect the wiring for the pod(s) being serviced. » Lift the buttons or shifter mechanism out of the pod and set aside. » Remove the 2 hex head screws used to fasten the pod to the dash, and then gently lift the pod off the dashboard. » Perform the desired repair or equipment replacement. » Re-install and fasten in place with the screws provided.
Service - 8
Control Pod, Buttons and Shifter Service
To service a Start or Radio Button... Refer to the Control Pod, Buttons and Shifter Service illustration. vVVVy
> Switch off the power to the game machine and unplug the AC line cord. Remove the Dashboard. Refer to service instructions for Dashboard. Gently remove the bulb(s) from the socket using a rocking motion. Perform the desired repair or equipment replacement. NOTE: If changing a bulb, simply reseat it in original socket. If repairing a button, unscrew the ring at the base and remove the button. Re-install the Dashboard and fasten in place with the screws provided.
To service View Buttons.. Refer to the Control Pod, Buttons and Shifter Service illustration.
VVVVVVV
Vv Switch off the power to the game machine and unplug the AC line cord. Remove the 4 tamper-resistant buttons used to fasten the faceplate. Pull the plate forward enough to expose the switches. Label and disconnect the wiring for the pod(s) being serviced. Lift assembly completely out of the pod and set aside. Perform the desired repair or equipment replacement. Reconnect wires and re-install buttons. NOTE: Insert the left edge of the button plate, then the right edge to fully seat. Check for pinched wires. Fasten the faceplate with the screws provided.
Service - 9
To service Shifter.. Refer to the Control Pod, Buttons and Shifter Service illustration. > > >
VVVV
Vv Switch off the power to the game machine and unplug the AC line cord. Remove the 4 tamper-resistant buttons used to fasten the faceplate. Pull the plate forward enough to expose the switches. NOTE: Pulling the shifter out of the pod requires quite a bit of force. Label and disconnect the wiring for the pod(s) being serviced. Lift assembly completely out of the pod and set aside. Perform the desired repair or equipment replacement. Reconnect wires and re-install shifter. NOTE: Orient the spring mechanism on the bottom edge of the shifter toward the floor and insert in pod followed by the top edge to fully seat. Check for pinched wires. Fasten the faceplate with the screws provided.
To service Steering Assembly... Refer to the Steering Assembly Service illustration. > > > Switch off the power to the game machine and unplug the AC line cord. Remove the Dashboard. Refer to service instructions for Dashboard. Remove 6 screws used to fasten the cover plate to the center of the steering wheel. Remove the cover plate and set aside. Remove the 3 screws used to fasten the wheel hoop to the shaft. Pull the wheel hoop off of the dashboard. Remove 4 flange nuts holding the motor shield, motor and shaft to the wheel assembly (Presence of motor shield not required on all cabinet styles). Slide the motor and the shaft off of the assembly. Perform the desired repair or equipment replacement. Re-install and fasten all items in place with the screws provided.
While the steering mechanism is exposed, inspect the belt for splits in the rubber or other signs of wear at the edges of the teeth. Install a new belt if necessary following the instructions below.
To service Steering Assembly... a >
> Loosen four mounting nuts for the motor bracket. Tighten the tension-adjust bolt only until there is no belt deflection, then loosen the bolt one full turn and tighten the four nuts. Reattach the mechanism and recalibrate the assembly.
Service - 10
MAIN ‘STEERING MECHANISM (SEE DETAIL DRAWING) CENTER CONTROL FERING BELT \ \ SHIFTER HARNESS
[SHIFTER POD
surTon POD! SPLIT Lock
Steering Assembly Service
To service Keypad... Refer to the Keypad Service illustration. » Switch off the power to the game machine and unplug the AC line cord. Remove the Dashboard. Refer to service instructions for Dashboard. Label and disconnect wiring for keypad. Remove the 4 nuts and set of spacers used to fasten the Keypad to the dashboard. Lift the keypad out. Perform the desired repair or equipment replacement. Re-install keypad, seat the spacers and fasten in place with the nuts provided. Re-install Dashboard and fasten with hardware provided. Vv
VVVVVVV
/—GEAR SHIFT CABLE
BUTTON POD ASSEMBLY Keypad Service
Service - 11
To service Lower Cabinet Speaker... This speaker is located just above the pedal assembly. > > >
> Switch off the power to the game machine and unplug the AC line cord. Unlock and remove the rear cabinet door. Label and disconnect the wiring, including ground strap, to Board assemblies attached to the electronics shelf. Remove the screws used to fasten the electronics shelf inside the cabinet, then remove the shelf and set it aside. Locate the speaker. Remove the nuts from the mounting screws before removing the speaker form the enclosure. Perform the desired repair or equipment replacement. Carefully reseat the seals upon completing any task in the speaker enclosure. Reconnect the wires, including the ground. Refer to the Cabinet Wiring Diagram for correct speaker polarity.
To service Pedal Assembly... > > >
Vv
Vv Vv Switch off the power to the game machine and unplug the AC line cord. Adjust the seat to the maximum rear position. Remove 4 tamper resistant screws used to fasten the Pedal assembly to the cabinet.
To service Coin Meter.. > > >
> > Switch off the power to the game machine and unplug the AC line cord. Unlock the cash door and swing it open. Remove the cash tubs. The meter is located on a plate at the vault bottom. Remove the screws and lift the plate just enough to disconnect the meter wires from the harness. Record the meter count before testing or replacement. Perform the desired repair or equipment replacement.
To service Coin Mechanism.. > > >
> > Switch off the power to the game machine and unplug the AC line cord. Unlock the coin door and swing it open. Unlatch and remove each coin mechanism separately to clean or replace with a different type. Ensure mechanism seats fully in the holder upon reinstallation. Close and lock the release latch, then close the door. Turn on the game and change the mechanism setup, then test known good and bad coins to verify operation.
To service Dollar Bill Validator... (Use MARS AE2411-U3 UL recognized currency changer) Dollar bill validators or other currency acceptors may be installed in games that are manufactured with the additional wiring connector. Refer to Dollar Bill Validator Service Illustration > >
> Switch off the power to the game machine and unplug the AC line cord. Unlock the coin door and swing it open. Read the label affixed to the door for additional information. Disassemble the validator and remove material to permit it to fit inside the coin door as illustrated then reassemble unit.
Service - 12
Dollar Bill Validator Service
To service CPU Board Assembly... VVVVYV
Vv Switch off the power to the game machine and unplug the AC line cord. Unlock and remove the rear door. Remove the perforated metal cover to expose the CPU Board Assembly. Carefully note the orientation of the JAMMA connector and the other cables. Extract the harness and other cables from the board connectors. Remove CPU board assembly mounting screws. Lift the board out of the cabinet and set in a safe place. Use anti-static bags and protective containers from new parts for storage if not reinstalled immediately. Perform the desired repair or equipment replacement. Be certain to reinstall the perforated cover so that it seals tightly against the metal plate.
To service Memory... The ROM (Read Only Memory) circuits contain the computer operating instructions for this game. Memory devices are especially sensitive to static charges. Use grounding precautions when handling these parts. VVVVV Switch off the power to the game machine and unplug the AC line cord. Unlock and remove the rear door. Remove the perforated metal cover to expose the CPU board assembly. Carefully note each IC position, and then remove using a chip extraction tool. To install memory circuits, orient a chip over the corresponding socket and press firmly to seat pins. Do not force.
Service - 13
To service the Battery... > > > Switch off the power to the game machine and unplug the AC line cord. Unlock and remove the rear door. Carefully note the position, and then gently lift the contact arm to release tension. Do not bend the arm. Slight finger pressure may be needed to pry the cell from its holder. Avoid direct shorts across terminals or from terminals to ground. To install a battery, orient cell near its holder and slide it in under the contact arm. Do not force.
To service Wheel Driver Board Assembly... > VVV Switch off the power to the game machine and unplug the AC line cord. Unlock and remove the rear door. Remove the perforated metal cover to expose the wheel driver board assembly. Carefully note the orientation of the cables. Extract the harness and other cables from the board connectors. Remove the wheel driver board assembly mounting screws. Lift the board out of the cabinet and set in a safe place. Use anti-static bags and protective containers for storage if not reinstalled immediately. Perform the desired repair or equipment replacement. Be certain to reinstall the perforated cover so that it seals tightly against the metal plate.
To service the Power Supply... > > > Switch off the power to the game machine and unplug the AC line cord. Unlock and remove the rear cabinet door. Unplug the IEC AC connector from the rear of the supply and the DC connector from the front. Remove the two front and two rear screws from the supply, then lift it off of the power chassis. Note voltage setting. Perform the desired repair or equipment replacement. Be sure to set the voltage switch to the correct value prior to reinstallation. Set the supply on the power chassis and align the mounting holes. Install the four screws and the two power connectors.
To service the Transformer.. a > > Switch off the power to the game machine and unplug the AC line cord. Unlock and remove the rear door. If the power to the Video Game Machine (VGM) was only recently disconnected, the transformer may still be warm. Allow the transformer to cool completely before handling. Label and disconnect all wiring, including ground. Remove the screws used to fasten the transformer to the base of the cabinet. Perform the desired repair or equipment replacement.
Service - 14
To service Fan Assembly... > VVVVV Switch off the power to the game machine and unplug the AC line cord. Unlock and remove the rear door. Remove the perforated metal cover to expose the fan assembly and set aside. Unplug the fan power connector from the wiring. Remove the screws used to fasten a fan down and then lift fan out. Perform the desired repair or equipment replacement.
To service Speakers in Head Rest.. Refer to the Seat Pedestal Service illustration. > > >
VVVV
a Switch off the power to the game machine and unplug the AC line cord. Remove the tamper resistant screws from the speaker grille. Remove the tamper resistant screws used to fasten the speaker plate to the seat and pull forward. Label and disconnect wires, including ground. Remove the nuts used to fasten the speaker to the plate and remove speaker(s). Perform desired repair or equipment replacement. Reinstall the speaker(s) to the speaker plate and reattach wiring, including ground. Attach the speaker plate to the seat. Reinstall speaker grille and fasten in place with hardware provided.
To service Speaker in Seat Back.. Refer to the Seat Pedestal Service illustration. VVVV
VVV Switch off the power to the game machine and unplug the AC line cord. Remove the tamper resistant screws used to fasten the grille to the seat and pull forward. Label and disconnect wires, including ground. Remove 4 Philips head screws used to fasten the speaker to the seat and remove speaker. Perform desired repair or equipment replacement. Reinstall speaker and reattach wiring, including ground. Reinstall speaker grille and fasten in place with hardware provided.
To service the Seat Assembly... The Seat Assembly includes the pedestal base. Refer to the Seat Pedestal Service illustration. > > Switch off the power to the game machine and unplug the AC line cord. Disconnect the Seat Assembly from the cabinet by removing 8 tamper resistant screws used to fasten the assembly to the slide rails in the cabinet. Slide the Seat Assembly halfway back along the rails to expose wiring. Disconnect the speaker cable and slide the seat the rest of the way off the rails. Remove 3 tamper resistant screws from each side of the seat mounting plate. Lift the seat and mounting plate assembly off the pedestal. Place the seat on its back, on a flat surface. Perform the desired repair or equipment replacement. Reinstall using the hardware provided.
Service - 15
Seat Pedestal Service
To service the Seat Slide Assembly... Refer to the Seat Pedestal Service illustration. » Switch off the power to the game machine and unplug the AC line cord. » Disconnect the Seat Assembly from the cabinet by removing 8 tamper resistant screws used to fasten the assembly to the slide rails in the cabinet. » Slide the Seat Assembly halfway back along the rails to expose wiring. » Disconnect the speaker cable and slide the seat the rest of the way off the rails. » Remove 3 tamper resistant screws from each side of the seat mounting plate. Lift the seat and mounting plate assembly off the pedestal and set aside. » Slide the seat assembly forward, and remove the two tamper resistant screws from the rear of the metal panel on top of the pedestal assembly. » Slide the seat assembly backward and remove the two tamper resistant screws from the front of the metal panel. » Lift the metal panel out of the pedestal base and turn the unit over. » Remove the four nuts holding the metal panel to the slide assembly. Set the metal panel aside and slide assembly is exposed. » Perform the desired repair or equipment replacement. » Reinstall by performing the steps in reverse and fasten in place using the hardware provided.
Service - 16
GCRUIS’N EXOTICA
SECTION
FOUR
PARTS
Cabinet Front View
04-12542.1 MOLDED MARQUE!
31-3373.2 BACKLIT MARQUEE 03-9895 EAR MARQU
ENT LAMP 01-14802 SPEAKER GRILLE 08-7456-21
CRT GLASS
DASH ASSEMBLY DECALS DETAIL DRAWING) ~y 5675-16273-00 MID RESOLUTION 27” MONITOR
03-9893.1 (SEE APPLICATION
04-10635__ COIN VAULT ENCLOSURE
04-12760-1 LEFT SECURITY BRACKET
CASHBOX DOOR—
OTHER ASSEMBLIES
LEFT DASH BRACKET 04-12461-1 RIGHT DASH BRACKET 04-12461-2 MAIN CABINET TREAD PLATE 01-1489 S
04-12760-2 RIGHT SECURITY BRACKET
SEAT/PED (SEE
Pedestal Assembly
4920.01123.268, 14-20 X 2-1/4 IMPER RESSTANT CAP SCREW 4-12959
- SUBORT BEAM
cases
4701-00005-00
- 174 sect togewasien —
4920-01124-16_- (@) 1/20 #1 BOLT
OTHER ASSEMBLIES
LEG LEVELER, 12-13 08-8028 SWIVEL CASTER, HARD, 25 DIA. 20-1036 SWIVEL CASTER SOFT, 2.5DIA. 20-10596 oo A70-00075:008 _ | SWIVEL CASTER, LOCKING, 2.5 DAl. 20-10361 (2) 298 8 00 Foe
Parts - 2
Cabinet Rear View o1-10714 LINE CORD COVER
5642-14632-00 [ON/OFF SwiTcH
03-8326
- HANOLE PULL/VENT
'5555-16059-00 J 88, SUB 01-13980 FRONT GRILLE ER SPEAKER
oe POWER SUPPLY /— (SEE DETAIL DRAWING)
ELECTRONICS ASSEN (SEE DETAIL DRAWI
SEAT/PEDESTAL ASSEMBLY _/ (SEE DETAIL DRAWING)
6.5 SUB WOOFER
(SEE APPLICATION
OTMERASENELEENOT HOM as agie \ BRACKET, PADLOCK 0111286 it sue BRACKET, KEY LOCK 01-11287 a Eye DETAIL DRAWING) BRACKET, AC PLUG —A- 23089 \_ CASTER WHEEL 1 \_ REAR D00R assMaLy (SEE DETAIL DRAWING) DETAIL DRAWING)
Rear Door Assembly
__01-8989 4108-01219-11 [UPPER DOOR LOCK CAM
- 8-32 X 11/16 SCREWS \ ~ / 01-7264 / {LOCK RETAINER PLATE __4420-01141-00
- 1/4-20 FLANGRIP NUTS
__01-11285 LOCK PLATE
4420-01141-00 | __20-10350
- 1/4-20 FLANGRIP NUTS DOOR LOCK ¢ M ASSEMBLY
4320-01164-20B
- 1/4-20 X 1 1/4 FLAT HEAD BOLTS
01-11291 DOOR BRACKET
aoe 03-7602 J 4320-01164-208 20" VENT HOLE COVER (a) 174-20 X 11/4 FLAT HEAD BOLTS
Parts - 3
Seat Pedestal Assembly
31-3974 seat Decal \ 44108-01193-108 \ H.29202 ‘SCREW WITH WASHER
- #8 X65 TAVPER RESISTANT — \ [/SERES SPEAKER CABLE 4406-01 128-00 f(s) 6-2 KEPS UTS pA est NS 5555-16223-00 \ tse 4 (2) TWEETER:
~ se 04-12765,
VA 4110-01001-20 @) #10 x 1.25 TAMPER RESISTANT SCREW
SPERKER. WOOFER N ‘|
o |
4110-01001-20
- #0 x 1.25 TAWPER RESISTANT SCREW
H.29575 WOOFER SPEAKER CABLE
H-23081.2 04124533 SEAT SPEAKER CABLE ‘SEAT SLIDE ASSEMBLY
OTHER ASSEMBLY
SEAT DC POWER CABLE H-23277
4924.01124-12 f~ (8) 1/4-20 & 2.1/2 TAMPER RESISTANT SOLT 4700-00091-00
E1125
- LOCKTTE BLUE 242-31
LoceTine Lu
4924-01124-08,
- s/r6-18 x 72— thee HEAD BOAT 4106-01042-12 [#8 x 374 seme
4702-00014-008 {8} 174 INTERNAL TOOTH } Lock ‘wasHER
\ \__ 4700-00075-008
- 1/4 FLAT WASHER \_o4-t2962.1 PEDESTAL
Parts - 4
AC Power Plug Assemblies __ 4004-01041-06 \ (2) 4-40 FLAT HEAD PHILLIPS SC 5102-14240-00 LINE FILTERT\
5733-12869-00 PANEL FUSE HOLDER \
4004-01041-06
- 4-40 FLAT HEAD PHILLIPS SCREW
01-15054 AC BRACKET COVER
Zo INE RD AND P
Parts - 5
Marquee Assembly
Parts - 6
Fluorescent Lamp Assemblies A-23252
20-10444 L LAMP HOLDER
20-10480 “~~ STARTER
4408-01128-00 NUT 8-32 KEPS
LLAST
< 24-8809 08 24-8874 . CONVENTIONAL LAMP BALLASTS Ean veS iS Ss YS
20-10263 1OOVOLT 50/60 Hz 20-8749-8 120VOLT 6OHz 20-1020 220VOLT SOHz 20-10384 220VOLT OTHER ASSEMBLY aeets very LIGHT FIXTURE SHIELD 04-12696
20-10380 240VOLI
20-10236 240V0LT 6
20-10444 LAMP HOLDER
4002-01105-04
SCREW #2-56 P-PH FLUO
20-10481.2
/ AMP HOLDER >s / H-22507
fi CABLE : 24-8809 ald FLOURES!
Parts - 7
Parts - 8 02-5370 4408-01 128-00
- KEYPAD MOUNTING \ ;— (6) 8-32 KEP NUT \ 03-7655-4 \ f° CABLE CLAMPS \ \ 20-10592
4404-01124-00
STEERING MECHANISM
) | _Heti24.4 // KEYPADS
(SEE DETAIL DRAWING) \ KS) 4= 40 °KEP NUS \ \ \ \
4408-01128-00 8-32 KEP NUT H-23266 _ START/RADIO BUTTON HARNESS. H-23263
LINE VOLTAGE
CABLE GROUND
H-22327,
GROUND BRAID)
Dashboard Assembly
4420-01141-00_|
- NUTS 1/4-20 FLANGRIP 04-12409.2._/
DASH PLATE
OTHER ASSEMBLIES KEYPAD CABLE 04-12928.1
Main Dash Assembly
4108-0121905, pane) DASH ASSEMBLY —/
04-12515.1, MOLDED MAIN gessis DASH START |
/ ana971-3 | PLASTIC DASH) | INSERT -THIRD |
5795-15067-20_/ 26 PIN RIBBON —/ CABLE
\_staart2 PLASTIC DASH INSERT - SECOND
f sraarta PLASTIC DASH INSERT FIRST 31-0216-2 (OVAL PUSH BUTTON RADIO
Steering Wheel
4028-01191-16B OCKET HEAD BOLT 1/4-28 x 1 STEERING W \ Mi ANISM
02-5345 Hut Lo B
_20-10189 LOCK WASHER EXTERNAL TOOTH
_ 20-10606 STEERING E1219 f REQ'D LOCKTITE 680 FEL
--4020-01100-20
- 1/4-20 x 1 1/4 AMPER RESISTANT CAP. STEERING WHEEL __/ MECHANISM KEY (SEE DETAIL DRAWING) 4427-01183-00 _| 03-9911 JAM NUT, 1/2-20 - EERIN
4701-00005-00B OK
- 1/4 SPLIT LOCKWASHER
TAMPER f
Parts - 9
Steering Mechanism 20-10627
AD LAVHS
YOLOWN 6208-rL 2 / J WA NSISNOILNELOd ONINZaLS _// 00-6062 1-vL0S
Parts - 10
Button Pod Assembly
__ 03-9797 / MOLDED BUTTON HOUSING
__ 4008-01041-10
- 8-32 X 5/8 FLATHEAD SC
4008-01093-10B
- 8-32 X 5/8 | TAMPER RESISTANT SCR
N MOUNTING BRACKET 31-2390-16 OVAL PUSH ? BUTTON — RED A-22781 PUSH BUTTON SWITCH OVAL ~~ 31-2390-17 ASSEMBL OVAL PUSH
BUTTON —WHITE OTHER ASSEMBLIES {| 31-2390-18 LAMP MINI-SWITCH, D41 5647-12133-00 PUSH LAMP BULB, 14V, #658 24-8828 TON — BLUE
Shifter Pod Assembly
03-9793 MOLDED SHIFTER HOUS
_ 4008-01041-10 [~(2) 8-32 X 5/8 FLATHEAD S
| 04-12410 SHIFTER MOUNTING BRACKET
Parts - 11
Shifter Assembly 20-10495
vA
nnnnnnnne
Parts - 12
Coin Door Assembly
KEY- NN S C . CAM LOCK—- & sec Po 36
wr | 27-3725
CAM LOCK ARM——F ENTRY/REJ ' BUTTON
i i
REJECT BEZEL
27-3731 CT FLAP
om
BLANKING PLATE
Lag
}-8863 SH TUB
STEEL ENCLOSURE
COIN METER
Parts - 13
Power Supply 20-10537
CORD —\ R \
H-20353 IDC AC KI2 CABLE
_»~5060-15755-00 E FILTER (REQUIRED EUROPEAN MODELS) 01-15100 / D.C. MAIN POWER, R SUPPLY R Suen CONNECTOR
—12 VDC BLUE
Electronics Assembly A-23075 14-1251 4 ID ELECTRONICS R,
A-22536 / 6PURSSEMBLY WHEEL ORIVER
__5556-13956-00 / 2 PIECE FERRITE BEAD
\ 04-10652-09 RIBBON CABLE W/FERRITE BEAD 5733-12869-00
- FUSE HOLDER)
OTHER ASSEMBLIES NOT SHOWN H-23493.2 GAME ae nie LED ADAPTER ASSEMBLY 04-11132 MAIN HARN
Parts - 14
U20 ¢¢ U22 ¢¢ 24 ¢¢
CPU Board Assembly A-22536
U26 ¢ ¢
3S A
DIP SWITCH SERIAL PORT |
Lop SWITCH 2
Parts - 15
Field Replaceab e CPU Board Parts
DESIGNATION | PART NUMBER FUNCTION DESCRIPTION
| U47 | 5460-15676-00 | Config Memory Backup | Module |
| F1, F2 | 5735-13853-00 | Circuit Protection | 2A SB Fuse 5x20mm |
| U2 | A-5341-16431-11 | Sounds | EPROM Assembly |
| U3 | A-5341-16431-14 | Sounds | EPROM Assembly |
| U4 | A-5341-16431-15 | Sounds | EPROM Assembly |
| U10 | A-5341-16431-1 | Programming & Images | EPROM Assembly |
| U11 | A-5341-16431-2 | Programming & Images | EPROM Assembly |
| U12 | A-5341-16431-12 | Programming & Images | EPROM Assembly |
| U13 | A-5341-16431-13 | Programming & Images | EPROM Assembly |
| U14 | A-5341-16431-3 | Images | EPROM Assembly |
| U15 | A-5341-16431-4 | Images | EPROM Assembly |
| U16 | A-5341-16431-5 | Images | EPROM Assembly |
| U17 | A-5341-16431-6 | Images | EPROM Assembly |
| U18 | A-5341-16431-7 | Images | EPROM Assembly |
| U19 | A-5341-16431-8 | Images | EPROM Assembly |
| U22 | A-5341-16431-17 | Images | EPROM Assembly |
| U23 | A-5341-16431-18 | Images | EPROM Assembly |
| U24 | A-5341-16431-19 | Images | EPROM Assembly |
| U25 | A-5341-16431-20 | Images | EPROM Assembly |
| U26 | 5347-16378-00 | High Score Memory Backup | Module |
| U53 | A-23250 | 27” Game Instructions | PIC Assembly |
Parts - 16
Wheel Driver Board 04-12770.1
Field Replaceable Board Parts
Description Part Number Designation
Fuse 4A SB 5731-14094-00 | F1, F2
| Fuse .63A FB | 5731-15627-00_| | F3 |
| PLD Assy Primary | A-23362 | U3 |
| PLD Assy Secondary | A-23363 | U3 |
Parts - 17
Supplementary Parts
Power & Protection AC Line Filter, 6A, 250V 5102-14240-00 Ferrite Bead, 1-1/4 SQ 5556-13956-00 Fuse Holder Panel 5733-12869-00
Cables Fire Wire Linking Cable, 16FT 20-10536-16 IDC Cable H-20353 Keypad Harness 04-12928.1 Line Voltage Cable H-23491.1 Main Wiring Harness H-23493.2 Ribbon Cable, 26 Pin 5795-15667-48 Seat DC Power Cable H-23277, USA DBV Acceptor Cable H-20398
Documentation Caster Installation Instructions 16-11010 DBV Installation Instructions 16-9637 Game Operation Manual 16-40072-101
Bolt, 4-20 x1 Product Registration Card 16-10650
Tools & Game Installation Hardware 4320-01124-16 Bulb, #161 24-8840 Bulb, #555, 6.3V, .25A 24-8768 Fuse, FB, .63A, 5x20mm 5731-15627-00 Fuse, SB, 1A, 250V 5731-06569-00 Fuse, SB, 3A, 250V 5731-10356-00 Fuse, SB, 4A, 250V 5731-06314-00 Fuse, SB, 4A, 5x20mm 5731-14094-00 Screw, #8 x 1-1/2 4108-01160-24B Screw, Tamper Resistant, 14-20 x 1-1/4 4020-01100-20 Torx Key, T-20 20-9620 Torx Key, T-27 20-10140 Washer, Flat, .265 x .626 x .067 4700-00135-00B Washer, Flat, .265 x .750 x .067 4700-00033-00 Washer, Lock, Internal Tooth, %4-20 4702-00014-00B Washer, Split, 4
Transformer Application Chart Part Number
Voltage & Country 5610-16292-00 4701-00005-00
5610- 16292-01 5610-16292-00
120 VAC _USA 230 VAC Europe 100 VAC Japan
Parts - 18
Line Cord Application Chart art Number | 5850- 5850- 5850- 5850- 5850- 5850- 5850com 14699-01 | 14699-02 | 14699-03 | 14699-00 | 14699-04 | 14699-05 | 14699-06 Country USA . UK . Italy . Japan . New Zealand . Germany . Spain . Denmark . Finland 5 Holland 5 Norway . Switzerland . Hungary . Canada . Austria . France . Australia . Belgium .
Coin Door Application Chart
Part Number
9-96023- | 02 | 03 | 04 | 06 | 07 | 09 | 11 | 13 | 14 | 15 | 17 | 18 | 20 | 22 | 23 | 24 | 33
Country USA . K (09-80000) Italy . Japan . New Zealand . Germany ° Spain . Denmark . Finland . Holland . Norway . Switzerland . Hungary . Canada . Austria . France . Australia . Belgium .
Parts - 19
NOTES
Parts - 20
CRUIS’N EXOTICA
SECTION FIVE
WIRING
Wiring - 2 JAMMA Chart FUNCTION WIRE COLOR PIN | PIN WIRE COLOR FUNCTION
| Ground | Black | A | 1 | Black | Ground |
| Ground | Black | B | 2 | Black | Ground |
| +5VDC | Red | Cc | 3 | Red | +5VDC |
| +5VDC | Red | D | 4 | Red | +5VDC |
| -5VDC | Yellow/Brown | E | 5 | Yellow | -5VDC | |
| +12VDC | Orange | EF | 6 | Orange | +12VDC | |
| Key | H | 7 | Key | ||
| N/C | J | 8 | Brown | Coin Counter 1 | |
| N/C | K | 9 | N/C | ||
| N/C | L | 10 | NC | |||
| N/C | M | 11. | NC | |||
| Video Green | Yellow/Green | N | 12 | Yellow/Red | Video Red | |
| Video Sync | Yellow/White | P | 13 | Yellow/Blue | Video Blue | |
| Service Credits | White/Gray | R | 14 | Yellow/Black | Video Ground | ||
| Slam Tilt | Black/Green | Ss | 15 _| Black/Blue | Test Switch | |
| Coin 2 | Black/Red | T | 16 | Black/Brown | Coin 1 | |
| N/C | U | 17_| | White | Start | |
| Gear 1 | Green/Black | Vv | 18 | NIC | ||
| Gear 2 | Green/Brown | Ww | 19 | White/Brown | Radio Switch | |
| Gear 3 | Green/Red | Xx | 20 | [NC | |
| Gear 4 | Green/Orange | Y | 21 | NC | ||
| NIC | zZ | 22 _| White/Yellow | View 1 Switch | ||
| N/C | a | 23 | White/Green | View 2 Switch | ||
| N/IC | b | 24 | White/Blue | View 3 Switch | ||
| N/C | c | 25 | NIC | |||
| N/C | d | 26 | NC | |||
| Ground | Black | e | 27 | Black | Ground | |
| Ground | Black | f | 28 | Black | Ground |
SOLDER SIDE COMPONENT SIDE
Dashboard Wires (Not part of the Main JAMMA Harness)
| Wheel Motor Black | Brown + | Green/ Black | Gear Shift 1 (1°) |
| Wheel Motor Red | Brown/ White - | Green/ Brown | Gear Shift 2 (2°) |
| Red/ Brown | +5V Steering | Green/ Red | Gear Shift 3 (37) |
| Orange/ Blue | Steering Position | Green/ Orange | Gear Shift 4 (4™) |
| Black/ Gray | Ground Steering | Black | Gear Ground |
DC Power Source Voltage Limits
| FUNCTION | RANGE LIMITS | ID | ID | RANGE LIMITS | FUNCTION |
| Digital Circuits | +4.90V to +5.10V | +5V | -5V_| | -4.72V to -5.25V | Audio; Lights | |
| Audio; DBV | +11.5V to +12.5V | 12V | NOTE: +5V is adjustable on the power supply. |
Cabinet Wiring
| Ss | Series Specker Coble, | H~23222 | PA cofS ew | ||
| 3 mm | Ne | . | wo oRG = ster Lame | gone | |
| es | [Leura | igo | RED GRY = Speckee | fer] GR | start |
| L | saciny| | REL | ‘ir BRN Raes ean — | |
MMO BLK = view 1 Lame JonG aux + view 1 Lame 2]
| Fr | UIE we Gna | we | iter > tore |
pow B |e rae ie ge Ke
| | | leneen ve en | M4 |
Fb fae ae ea) fe Cate shud care i
| st | a | . | Hy | aig Sit Cone | ||
| TE vie- Sd) | WEL | Gear Suit + | ce | gO | Si | one |
| BIE ec | ne sc. | | ACRE) Gear | Si | B |
Iauue veo Seer
| [3 ||3 [GREEN vig Grr | = | ne | ||||
| FP | feo we ne | ale | ||||
| Ald | 2 | AK | Grant | E | ||
| : | ELA — | Ground | b| Be | |||
| 6 Pin 084 | a | RED Bin +5v (Fused) | > -h | |||
| { | Heowy Line indicates | fer] | Pee | |||
| aT | 40 O86 woo tera] | fran/coble rout'ng ff [ORC ALU steerne pa | —E| 2 ORS AED | |||
| ee! | ORG BLK her Lar | from PC Boords to ff (EK Ca¥ Gouna (eet) | [3 [reace | |||
| { | wo-eectestarels| — Contot Pare, Coin | fI-Semonn —s vnast Water = | BLACK | |||
| a | Ri | tos Lae | oor, and Soeakers, | TERN WHT= Wheel Motor | (ees | Gworor |
| BUC | To optional | AG | ||||
| mt | Overhead orquee | fr | ||||
| 1 | “ | MAIN HARNESS: | j2| |e |
; B| BRN Is | Is el BI is
| oso) | BEERS | an | ||
| oe oto | s6888 | rr | eax] fr | |
| rast | eae | b | foe 1] [| en | ||
| ' | Ini 2 | {3 |(3 fax METIS | 13) | Disploy | |
| tN | [wo vel ver Lomas | EE bel | i | 3 favace | [3] Disploy |
| ni | (ome sx suart Lama. ¢ | Free | fs | 5 fauack | js] PB |
| oan | face | eee |
me 8 Beta
| soo | 23 | sé Kemet TE | ||||
| 8 | = | YEL BRN -SvOC_ (Loma) fF] ff | ||||
| r | Bice | Lama reine | |b | |||
| 3] | ap | Bac — Cra | ||||
| S| | 38 | | | CK BAN Core | i fa | ||
| al | 43 | BuCeED eon 2 | | 5 | |||
| @ | we | RED Bx +S¥0C. | elle | |||
| L__| | &| | ex | ||||
| ACAcK | Ground | os 8| | 8 | Dg | RoW coin voter te | [2 | |
| A | on 8 | om] | ee | 1B Pc | |||
| po fs | 7 | K G2 Som 1 | fofBL GaN | |||
| 100 ff | if | le | ta) | |||
| bE | RG | ave aioe | z | a | Se Bux | i] | Reg -veteR |
| E | foi, | soaks) | E | oats | | | joe cuelen | |
| B Face wet Bela | “ | | |e tere | ||||
| ene voume — f | aa | & | slack | e | ||
| ke | sce] | gt | 8 | Bin ORE | s | |
| ao | i | BUC | 3 | |||
| co | Es | BUC | & | |||
| Et | z | BLACK | Ground | __{7) | [yALAGK | |
| 3, | 1a0)3 | 2) pete | fue es | : | zh | bE | ||
| ° | is | iB) Cette | ft mar Stina | s | ails | fs FRE | |
| he | sure | | BIE | a | |||
| be | L | ‘[GOIN_VAULT ASS. | ||||
| Re | fR | em | FOOT PEDAL ASSM. | |||
| ea | ft | “Lew | RED GaN _+5y (Fused) (p_RED | |||
| ero, | | ey wit eee] PS, | Seg | tea Pees h | | Loewe | eS | ||
| ua) | | BROWN | —=Mser 2 | (2 | OREGRY Brave Peas [| ff our cey Ma srake. | |||
| eu | via} | L | i | rE | | ee | ooe |
ad —
| Ne | oD Gu | +055 Sp | ED GRY |
Pine Ly
| a | iB | ass | ||
| 1S | ey ay ows BSH | ft | =H | | SPEER |
| LL 8G, | BIE | ‘ | si | |
| elu el | 1 Power Cave t-zazny | ase Seether Gale 23218 |
ay
| is | cD BK IF]; [aa ak | RED LX SC) To pid Powent | ||||
| [EtTcmx, | hin 1 must meteh solid Golr on Raton Cable | ary Computer Grae | BLA | | au | | | LK | “Ground fp | Waton Seot (40078) |
| ue | oe | 2a oe we | ||||
| Ps | 7 eas is Se anew | Jes ane SEAT ASSEWELY) |
gece’ | [2 Leer’
| rr | = | [ | SRN WET | —a |
| TMMMMIEIM] Linking | Connector | 5 | See | |
| 9 | i | pence | ||
| mmm) Ribbon | PCB | 4 | ||
| Coble | B | = |
Wiring - 3
Wiring - 4
Power Wiring Diagram
fon
AC POWER CORD
NY 100 Power Cot 580-1927100
POWER SWITCH
BLKRED (> _BLKYEL_ HOT | ___ | BLACK LINE SRN EL neuen ~< ware
WHT RED.
Power Inlet
Mounting Plate
10.PIN ‘COMMON BLOCK BLACK BLACK 54 4
BLACK [Black 2 |l2
BLACK BLACK BLACK WHITE To Seat Speaker Connection on Main Hames
RN YEL BLACK ‘GRN YEL WHITE BLACK ‘GRN YEL WHITE O6¢ BLACK 55 BLACK GRNYEL |S 5 | 3 | GRNYEL WHITE | WHITE H-20353 LIGHT.
RED VIO BRN VIO KEY RED WHT BRN WHT GRN YEL ‘GRN YEL FEMALE
“Transformer BLUBLK —_36Vrms
BLUE BLU WHT WHT BRN WHITE WHT BLK
VIDEO MONITOR: POWER SUPPLY 2FT IDC Power Cable FIXTURE For optional Dollar Validator, et To Seat Speaker Cable In Seat Assembly TRANSFORMER
CPU Board LED Indicator Status Chart
| DESIGNATION | LOCATION | FUNCTION | COLOR | STATE | MEANING | ||
| LED6 | Bottom Center | Diagnostic | Green | Off | Abnormal Game Play |
On Abnormal Game Play
Blinking Signals Normal Game Play
| LED5 | Bottom Center | 7e) | Green | Off | PIC Recognized |
On PIC Not Recognized
| LED 4 | Bottom Center | Sound | Orange | Off | Abnormal Operation |
On Abnormal Operation
Blinking Signals Normal Operation
| LED 3 | Bottom Center | Power | Red | Off | Power Not Received |
On Signals Normal Operation
Blinking Abnormal Power Reception
CPU DIP Switch 1 Settings
Function swi sw2__SW3__SW4_SW5__—SW6_SW7__SW8
Dedicated OFF
Kit ON
Motion Disabled OFF Motion Enabled ON Stand Up Style Cabinet OFF Sit Down Style Cabinet ON Wheel Invert Disabled OFF Wheel Invert Enabled ON Unused OFF ON Link Disabled OFF Link Enabled ON Linking I.D. Number Master (Game Number 1) OFF | OFF
| Slave (Game Number 2) | ON | OFF |
| Slave (Game Number 3) | OFF | ON |
| Slave (Game Number 4) | ON | ON |
Wiring - 5
CPU DIP Switch 2 Settings
DIP Switch 2 Settings SWi | SW2 | SW3 | SW4 | SW5 | SW6 | SW7 | SWS COUNTRY CODE USA OFF* | OFF* | OFF* | OFF* | OFF* GERMANY ON | OFF | OFF | OFF | OFF
| FRANCE | OFF_[_ON | [OFF | [OFF | OFF |
| CANADA | ON | [ON | OFF | OFF | OFF |
SWITZERLAND OFF | OFF | ON | OFF | OFF ITALY ON | OFF | ON | OFF | OFF
| UK | OFF | [ON | ON | OFF | OFF |
| SPAIN | ON | [ON | ON | OFF | OFF |
AUSTRALIA OFF | OFF | OFF | ON | OFF JAPAN ON | OFF | OFF | ON | OFF
| TAIWAN | OFF | [ON | OFF | ON | OFF |
| AUSTRIA | ON | [ON | OFF | ON | OFF |
| BELGIUM | OFF | OFF | [ON | ON | OFF |
SWEDEN OFF | OFF | OFF | OFF | ON FINLAND ON [| OFF [| OFF | OFF | ON
| NETHERLANDS | OFF | [ON | OFF | OFF | ON | ||
| NORWAY | ON | [ON [| OFF | OFF | ON | ||
| DENMARK | OFF | [OFF | [ON | OFF | [ON |
| HUNGARY | ON | [OFF | ON | OFF | ON | ||
| GENERAL | ON | [ON [ ON | OFF | ON | ||
| USAT/GER(/FRI/SPNT/AUSTRIAT/GENT | OFF__[_ | OFF | ||
| USA3/GER1/FR1/SPN1/AUSTRIA1/GEN3 | ON | [OFF | ||
| USA7/GER1/FR1/SPN1/AUSTRIA1/GEN5 | OFF_[ | ON | ||
| USA8/GER1/FR1/SPN1/AUSTRIA1/GEN7 | ON | ON | ||
| CANT/SWIT/ITL1/UK 1/JPN1/TWN1/BLGN1 | OFF__[_ | OFF | ||
| CAN2/SWI2/ITL2/UK2/JPN2/TWN2/BLGN2 | ON | [OFF | ||
| CANS/SWIS/ITLS/UK3/JPN3/TWNS/BLGNS | OFF_[ | ON | ||
| NTHRLDS1/FNLD1/NRWY1/DNMK1/HUNT | OFF__[ | OFF |
NTHRLDS2 ON | OFF
- Denotes default setting. Switches 1 through 5 select country. Switches 6 and 7 are used to select one of four modes for each country.
NOTES ON COINAGE: There are many ways to select the type and quantity of currency recognized by the game machine.
- The most common coin combinations for several countries are pre-programmed and can be selected from the table when Standard Pricing is activated (see Game Adjustments).
- DIP Switch settings may be changed with the power switched on. Set any switch and then observe the screen to verify that the desired selection is enabled. NOTE: If CMOS Coin Settings are active, switch settings for an individual Country will have no effect.
- Some European countries may accept currency used in other countries. The most popular coinage settings are listed beneath ‘Other’ in the Standard Pricing Table.
- Alternate settings are listed beneath ‘General’ in the Standard Pricing Table.
Wiring - 6
CRUIS’N EXOTICA
GCHAPTER
SIX
TROUBLESHOOTING
CN 7 (IR
@ Before servicing electronics, turn off AC power to the VGM. Wait for capacitors to discharge.
@ Before touching or handling electronic assemblies, discharge static electricity on your body. To discharge static, begin by connecting the line cord to a properly grounded outlet, but do not turn on the power! Next, touch the safety ground stud of the power supply chassis.
@ Store electronic assemblies in an anti-static area. Use anti-static bags to store or transport circuit boards. Transport the hard drive in original shipping container.
# Do not remove or connect electronic assemblies when power to cabinet is switched on. Otherwise, you'll damage electronic assemblies and void the warranty.
@ Replace ground wires, shields, safety covers, etc. upon completion of maintenance or service. Install and firmly tighten all ground and mounting screws.
Coin Mechanism and Pricing Troubleshooting Table
SYMPTOM
- Video Game Machine (VGM) accepts currency or tokens, but number of credits per coin or bill is incorrect. CAUSE
Improper settings at Pricing Menu REQUIRED ACTION
Press and hold TEST MODE switch inside coin door to enter Menu System. Select SWITCH TEST from Diagnostics menu. Conduct test to confirm operation of game switches. Select PRICING MENU from General Adjustments Menu. Verify units and credits are set correctly.
Faulty wiring Confirm cabinet wiring is correct for this game. Assure coin meter and coin switches connect properly to control input wires.
- VGM will not accept currency or tokens.
- VGM will not enter play mode.
+ Audio and video are present. Improper currency Unlock and open cash door. Empty cash box and inspect revenue for counterfeit currency. Check vault. Remove any items that block path from mechanism.
Faulty coin mechanism RON Unlock and open coin door. Check each mechanism for proper mounting. Remove mechanism. Clear currency path. Reinstall mechanism and close latch.
Tilted coin mechanism or game Verify mechanism is level after doors close. Repair or replace coin door if it is bent or damaged. If necessary, adjust cabinet leg levelers to keep mechanisms level.
- Coin indicators do not light Burned-out bulb Burned-out bulbs may appear white or darkened. Check continuity with digital voltmeter. Replace burned-out bulb with an identically rated part.
Open fuse circuit Check fuse continuity with digital voltmeter. If fuse is blown, replace fuse with an identically rated part. If fuse isn’t blown, check wiring.
Troubleshooting - 2
Coin Switch and Meter Wiring
FACTORY STANDARD
| COIN SWITCH 1 | JAMMA PIN 16 | JAMMA PIN 8 |
COIN
| COIN SWITCH 2 | AMMA PINT | || | METER | y |
| COIN SWITCH | JAMMA GROUND | JAMMA *5VOLTS |
‘COMMON
OPTIONAL WIRING
| COIN SWITCH 1 | JAMMA PIN 16 | JAMMA PIN 8 |
COIN SWITCH 2
| COIN SWITCH | JAMMA GROUND | JAMMA +5VOLTS |
COMMON
INCORRECT WIRING
Aconnection between JAMMA coin input pins will cause twice the desired credits for each coin inserted. Acoin meter with a defective or missing diode may eventually damage driver circuits on the CPU Board.
| COIN SWITCH 1 | JAMMA PIN 16 | JAMMA PIN 8 |
COIN
GOIN SWITCH 2 JAMMA PINT 5 || METER
| ‘COIN SWITCH | JAMMA GROUND | JAMMA +5VOLTS |
COMMON
Troubleshooting - 3
Startup Troubleshooting Table
SYMPTOM
- Video Game Machine (VGM) does not start.
- VGM appears completely non-functional.
- No audio
- No illumination
- No video display CAUSE
Power problem REQUIRED ACTION
Check power is switched on. Make sure fans are turning. If not: Is the power supply connected to its power cable? Is power supply turned on? Plug cord into AC power outlet. Verify presence of AC line voltage.
Improper line voltage switch setting Turn off power. Unplug AC line cord. Check line voltage switch. If necessary, set it to agree with local AC line voltage. Retest game.
Open fuse
Ag Turn off power. Examine AC fuse on power chassis. Examine DC fuses on cabinet wall or electronic equipment shelf. Replace faulty fuses with identically rated parts. Turn on game power. If fuse opens again, check DC wiring harness and connectors.
Faulty wiring Remove line cord. Test line cord, power plug, and IEC connector for breaks or damage. Verify continuity of each wire in cord. Install cord on power chassis. Press connector firmly to seat it. Assure that cabinet wiring harness connectors fully seat in corresponding power supply and board connectors. Inspect wiring for breaks or damage.
Troubleshooting - 4 Location of Power Supply and Line Cord
Startup Troubleshooting, continued
SYMPTOM
appears non-functional.
+ Currency acceptor price indicator is illuminated. CAUSE
+ Video Game Machine (VGM) | Power problem REQUIRED ACTION
Inspect circuit boards under low-light conditions. The LED's glow and the fan turns when processor circuits receive voltage and indicate presence of DC from power supply. However, voltages or signals may not be normal. Turn on power. Set the digital voltmeter to the 20-volt DC setting and measure DC voltages at power connector pins. Adjust the +5V source if necessary. Refer to Cabinet Wiring Diagram for specific wiring information and voltage limits. Set the digital voltmeter to the 2-volt AC setting and measure DC voltages at power connector pins. Any reading here indicates that supply voltages are unstable and may contain ripple or noise.
Faulty wiring Turn off power. Check wiring harness connectors attach and fully seat onto mating board connectors. Verify harness connects to CPU Board. Check other connectors in same way.
Improper DIP switch settings Verify switches are set as intended. Check DIP switch settings.
Faulty circuit boards
& Run power-up self-test sequence. Note errors or failures during test. Compare LED's with LED indicator status charts. Note discrepancies. Press and hold TEST MODE switch inside coin door to enter Menu System. Select MONITOR TEST from Diagnostics Menu. Conduct test to confirm operation of each screen used in the game.
Front View of Coin Door
Troubleshooting - 5
Startup Troubleshooting, continued
SYMPTOM
- Video Game Machine (VGM) does not start.
+ VGM accepts currency or tokens.
- Audio and video are present.
Troubleshooting - 6 CAUSE
Faulty coin mechanism REQUIRED ACTION
Unlock and open coin door. Check each currency acceptor to assure proper mounting. Verify each release latch is closed and locked. Test mechanism with good and bad coins to see if mechanism accepts and rejects currency correctly. Inspect to see if external acceptor indicators (Pricing, Flashing Arrows, etc.) are lit. Verify each acceptor operates properly by placing it in working game. Replace bad parts.
Faulty switches Press and hold the TEST MODE switch inside coin door to enter Menu System. Select SWITCH TEST from the Diagnostics Menu. Conduct test to confirm operation of each switch. Assure no loose parts or wires are caught in switch contacts. Check for continuity in each suspect switch connection (Common to Normally Open or Common to Normally Closed). Replace faulty switches (bent levers, broken actuators, etc.).
Faulty wiring Assure no wires are caught in hinges, latches or switch contacts. Check wiring continuity from circuit board connectors to acceptors.
Interior View of Coin Door
Linking Problem Troubleshooting Table
SYMPTOM
- Cannot connect multiple Video Game Machines (VGMs) together CAUSE
Faulty wiring REQUIRED ACTION
Do not extend linking cables supplied with VGM. Install required crossover between cabinets. Each coupler connects two VGMs (one pair). Do not use standard telephone type couplers or wiring for linking. Use only 10 Base-T, Ethernet-type, Category 5, twisted-pair wiring.
Improper linking hardware Use required network hub for your local network. A Hub Link Kit permits up to eight VGM connections. Array completion requires basic kit brackets and spacers.
- VGM does not recognize other players in linking Operation
- VGM functions normally by itself Improper settings Record any error messages that occur during self-test. From the Diagnostic Menu select DIP SWITCH TEST. Confirm the link is enabled. Be sure that each VGM has a unique ID number. Select LINKING TEST from the Diagnostic menu. Run tests for each linked VGM.
Power problem Verify the hub receives power. AC adapter wires are thin and easily damaged.
Faulty wiring (3 or more VGMs) Inspect hub indicator lights. Illuminated indicator lights for each active port light up if the cable(s) are properly connected. Check for cable continuity from hub to VGM for each indicator that failed to light. Assure no loose wires are caught in hinges, doors or under cabinet. Verify linking cable connects to CPU Board for each game. Verify each linking cable operates properly by placing it in working game.
Troubleshooting - 7
Linking Problem Troubleshooting, continued
SYMPTOM
+ Some Video Game Machines (VGMs) in the group link properly, while others do not. CAUSE
Improper hub switch setting REQUIRED ACTION
Assure switches on hub are set according to Hub Link Kit instructions. (Networked VGMs do not require couplers. Hub has electronic crossover.) Inspect hub indicator lights for link activity. See manufacturer's literature for diagnostics.
Wrong software version Verify all linked VGMs use same version of software. Error message “VERSION MISMATCH” will appear if you try to link different versions. Contact your distributor.
Faulty wiring (2 VGMs) Insert crossover connection between coupled VGMs. Standard couplers appear identical to devices supplied with games, but do not include an internal crossover. Verify each linking crossover coupler operates properly by placing it in a working link between two VGMs.
Faulty wiring (3 or more VGMs) Use an additional crossover connector and cable to extend game or hub link connection. Two crossovers cancel each other out and results in same problem as no link crossover. Connect cables directly to hub. Do not use a crossover coupler and hub together in single network. Separate communications wiring from other wiring. Wires that must cross can only cross at right angles to limit noise pickup.
Troubleshooting - 8
Player Control Troubleshooting Table
SYMPTOM CAUSE REQUIRED ACTION
| * — Intermittent or completely | Faulty switches or | 1. | Press and hold TEST MODE switch inside coin |
| non-functional player | lamps | door to enter Menu System. Select SWITCH |
controls TEST from Diagnostic Menu. Conduct tests to confirm switch and lamp operation.
| * | Video Game Machine (VGM) | 2. | Check for loose parts or wires caught in switch |
starts normally. contacts.
- Check continuity at each switch connection (Common to Normally Open or Common to Normally Closed).
- Verify player control operates properly by placing it in working VGM.
- Verify light bulbs used for dashboard switches are type specified in parts listing. Other types will light, but may produce too much heat. Excess heat may cause switches to bind.
| Faulty switch wiring | 1. | Check for wires caught in door hinges, latches, |
or switch contacts.
- Verify harness connectors are attached and fully seated.
- Assure control switches connect properly to control input wires.
- Check cabinet wiring is correct for this VGM.
| * — Steering pulls to one side | Faulty Wheel Driver | Find power amp on Wheel Driver Board's large |
Board heatsink. Test and replace bad part or board.
| * | No wheel feedback | Improperly set | 1. | Select STEERING WHEEL TEST on the |
feedback Diagnostics Menu.
| * — Steering aims vehicle as | 2. | Set feedback to match player requirements. |
expected Maximum force may be too extreme for very young or inexperienced customers.
| Faulty circuit | 1. | Examine fuses and cables on Wheel Driver |
Board.
- Check cables and wiring between CPU board, wheel driver and motor.
- Check resistance of motor series resistors.
- Replace bad parts.
| Faulty motor | 1. | Turn off power. Open dashboard. | Support |
steering wheel and remove outer mounting screws.
- Remove metal shield (if VGM has one) over motor.
- Unscrew caps.
- Inspect motor brushes. Replace worn parts.
Troubleshooting - 9
Player Control Troubleshooting, continued
SYMPTOM
- Sloppy, unpredictable or ineffective steering
+ Video is present
- Video Game Machine (VGM) operates normally CAUSE
Blocked or faulty fan REQUIRED ACTION
Fan located on power supply functions as an exhaust fan. With power on, check airflow near each fan to assure that nothing blocks airflow.
Faulty mechanical parts Turn off power. Open dashboard. Support steering wheel and remove outer mounting screws. Remove metal shield (if VGM has one) over motor. Inspect for faulty or worn belts, bearings, couplings, gears, etc.
Faulty Wheel Driver Board Inspect Wheel Driver Board under low-light conditions. To indicate presence of AC from the transformer the LED’s glow when receiving voltage. However, voltages or signals may not be normal. Examine fuses and cables on Wheel Driver Board. Replace bad fuses. Use digital voltmeter to verify AC voltage between each fuse holder and ground. You should measure approximately 25V. See Wiring Diagram. Use the 20-VAC setting on digital voltmeter to measure DC voltage at motor. Do not move steering wheel, drive belt, or motor while making this measurement. Any reading _ indicates unstable supply that may contain ripple or noise. Select the STEERING WHEEL TEST from the Diagnostic Menu. Follow on-screen instructions to verify operation of the wheel motor and steering position sensor. Verify proper operation of Wheel Driver Board by placing it in working VGM.
Loose or worn drive belt Turn off power. Open dashboard. Support steering wheel and remove outer mounting screws. Remove metal shield (if VGM has one) over motor. Inspect for faulty or worn belts, bearings, couplings, gears, etc. If drive belt isn’t worn or damaged, check its tightness.
+ Inability to make a transmission selection.
- Video Game Machine (VGM) Operates normally. Improper DIP Switch setting(s) From the Diagnostics Menu, choose DIP SWITCH TEST. Make sure DIP 1, SW 1 is set to the OFF position.
Troubleshooting - 10
TENSION BOLT
How to Adjust Belt Tightness
4—SPEED SHIFTER
Player Panel Controls
Troubleshooting - 11
Video Troubleshooting Table
SYMPTOM
- Monitor appears nonfunctional
+ Audio is present
- Video Game Machine (VGM) controls operate normally CAUSE
Power problem REQUIRED ACTION
Verify connection of AC Power to video monitor. Inspect neck of CRT in dim light. Glowing filament near CRT base confirms monitor circuits receive power. However, voltages or signals may not be normal.
Faulty wiring Turn off game power. Verify that video signal and Remote Adjustment Board connectors seat properly on Video Monitor Board. Assure that no wires are caught on chassis or mounting brackets.
Improper monitor adjustments Check BRIGHTNESS (intensity) and CONTRAST are set above their minimum levels.
Faulty monitor circuitry Examine AC line fuse on Video Monitor Board. If fuse is faulty, replace it with an identically rated fuse. If the fuse is good, verify video monitor operates correctly by placing it in working VGM. If monitor is bad; Check monitor power supply. If the power supply is good, Check monitor horizontal output transistor and related circuitry.
+ Graphic images from game do not appear
- No audio
+ Power-up self-test runs
Troubleshooting - 12 Improper components Verify circuit boards are correct for this game. Label on each board record manufacturers’ name, assembly number and program version. Verify ROM instruction set is correct for this game. Game set includes more than one ROM. Label on each ROM records assembly number and software version.
Faulty Circuit Board Allow game to load normally. Note and record any error messages that occur during self-test. Press and hold TEST MODE switch inside coin door to enter Menu System. Select Diagnostic Menu from the Main Menu. Then select CPU BOARD TEST. Conduct this test to check operation of critical components. Turn off power. Inspect CPU Board to ensure JAMMA cable connector is fully seated onto the mating edge connector of the CPU. Check all other cable connectors for correct alignment and continuity. Compare activity of LED’s on CPU with the CPU Indicator Chart.
Power Problems Turn on Power. Use 20-volt DC setting on digital voltmeter to measure DC voltages present at Power connector pins. Verify +5V source if it is adjustable. Refer to Cabinet Wiring Diagram for specific wiring information and voltage limits. Use 2-Volt AC setting on digital voltmeter to measure DC voltages at Power Connector pins. Any reading indicates the supply voltages are unstable and may contain ripple or noise.
>
Typical Cutaway Rear View
Troubleshooting - 13
Video Troubleshooting, continued
SYMPTOM
+ White areas at screen edges appear tinged with color
- Dots at screen edges appear ovoid or cylindrical CAUSE
Picture tube dynamic convergence is out of alignment REQUIRED ACTION
Have service bureau dynamically re-converge monitor. This procedure requires removing and repositioning yoke. Service bureau must follow instructions from monitor manufacturer.
- Video images tear or roll, or have black bar down middle of screen Faulty wiring
| Check | connectors | and | cables | for | wiring |
continuity. Video cables connect circuit boards to video monitor. Assure connection of all cabinet ground wires, especially at video monitor chassis.
Faulty monitor circuitry Verify video monitor operates correctly by connecting it to working Video Game Machine (VGM). Assure video monitor is correct type for this game. Video monitors with wrong resolution can’t lock sync.
Improper sync signals Check to see if Video Board puts out type of sync that your monitor requires. Verify jumpers are set correctly for monitor.
Electromagnetic fields
| Move | cabinet | far | away | from | machines, |
appliances, or competitors’ video games.
- Missing colors Faulty wiring
| Check | connectors | and | cables | for | wiring |
continuity from circuit boards to video monitor.
Faulty monitor color drive circuitry Verify video monitor operates correctly by connecting it to working Video Game Machine (VGM).
- One color is dimmer or brighter than others
+ Whites appear tinted everywhere on screen Maladjusted color bias pots BONS
aa Turn on Video Game Machine (VGM). From Diagnostic Menu select MONITOR TEST. Watch Color Bars screen in mirror. Adjust three bias pots for best colors. (Most monitor neck boards include these pots.) Check White Screen. Touch up controls. If whites still seem tinted, have service bureau rejuvenate picture tube.
+ Picture is dim or faded
Troubleshooting - 14 Maladjusted BRIGHTNESS pot or subnormal picture tube emission From Diagnostic Menu select MONITOR TEST. Watch Color Bars screen. Adjust BRIGHTNESS and CONTRAST pots for greatest number of grays. You'll find these pots on Monitor Remote Control Board, behind coin door. If pots have no effect, have service bureau rejuvenate picture tube.
SYMPTOM
Picture is too narrow Video Troubleshooting, continued
CAUSE
Maladjusted WIDTH pot REQUIRED ACTION
From Diagnostic Menu select MONITOR TEST.
| Watch | Crosshatch | Screen | while | adjusting |
WIDTH pot for best picture. You'll find this pot on Monitor Remote Control Board, behind coin door.
Picture is too short Maladjusted HEIGHT pot or damaged vertical circuit From Diagnostic Menu select MONITOR TEST.
| Watch | Crosshatch | Screen | while | adjusting |
HEIGHT pot for best picture. You'll find this pot on Monitor Remote Control Board, behind coin door. If pot has no effect, service vertical output circuit.
Picture seems shifted to one side Maladjusted HORIZONTAL POSITION pot From Diagnostic Menu select MONITOR TEST.
| Watch | Crosshatch | Screen | while | adjusting |
HORIZONTAL POSITION pot for best picture. You'll find this pot on Monitor Remote Control Board, behind coin door.
Keystone-shaped picture Shorted turns in yoke Substitute working yoke. Have service bureau converge monitor. Retest monitor.
Blotches of color appear on screen Picture tube aperture mask is magnetized Demagnetize monitor with external degaussing coil. Take care not to magnetize neighboring games. Monitor may be left on or off during this procedure.
White areas in center of screen appear tinged with color
Object edges have fringe of one or more colors Picture tube purity or static convergence is out of alignment Turn on Video Game Machine (VGM). Press and hold TEST MODE to enter Menu System. Select Diagnostic Menu from the Main Menu. Select MONITOR TEST. Perform tests for Crosshatch, Red, Green and Blue screens to find clearest display of problem. Display screen with the most severe problem. Display Crosshatch Screen. Locate purity and static convergence ring magnets on back of monitor neck. Watch screen in mirror. Adjust magnets to minimize problem. Follow instructions from monitor manufacturer. Display Crosshatch Screen. Touch up adjustments while watching screen in mirror.
Troubleshooting - 15
Audio Troubleshooting Table
SYMPTOM CAUSE REQUIRED ACTION
| * | No audio | Improper volume | Press and hold TEST MODE switch inside coin |
setting door to enter Menu System. Select VOLUME
| * | Video is present | MENU from the Main Menu. Make sure the |
Attract Music is on (enabled). Verify all volume
| * | Video Game Machine | levels are set well above zero. If necessary, |
(VGM) appears to operate change levels to make game audible. normally
| Faulty wiring | Turn | off | power. | Assure | wiring | harness |
connectors attach and fully seat onto mating board connectors. Verify harness connects to CPU Board. Check audio cable connectors in same way.
Faulty or obstructed Remove grilles and inspect speakers. Free speaker speaker cones, terminals, mounting screws and magnets of loose parts or wires.
Faulty Audio Board Verify proper operation of Audio Board by placing it in a working VGM.
Power Problems Use 20-volt DC setting on digital voltmeter to measure DC voltages present at Power connector pins. Verify +5V, -5V and +12V sources. Refer to Cabinet Wiring Diagram for specific wiring information and voltage limits.
| * | Audio is distorted, muffled | Faulty or improper | 1. | Turn off power. Remove grilles and check |
| or has missing | speaker | speakers. Verify that speakers are full range |
frequencies. (100 to 10,000 Hz response) and rated for at least 20 watts. Woofers must be rated for at least 40 watts.
- Verify proper speaker operation by placing speaker in question in a working VGM.
Faulty wiring Multiple-speaker installations: Check for reversed wires at one speaker. Weak or low frequencies and thin or hollow sound quality are symptom of incorrectly phased speakers. Sound tests may not detect this condition, but you can hear it during operation.
Improper Setting Press and hold TEST MODE switch inside coin door to enter Menu System. Select SOUND TEST from Diagnostics Menu. Increase volume as required. This test will verify some audio circuit functions.
Troubleshooting - 16
Audio Problems, continued
SYMPTOM
Dead sound channel CAUSE
Faulty speaker REQUIRED ACTION
From Diagnostics Menu, choose SOUND TEST. Recheck speakers with audio signals provided by test.
- Verify proper speaker operation by connecting speaker in question to working Video Game Machine (VGM).
Faulty circuit board Run power-up self-test sequence. Note errors found during tests. Compare circuit board LED's with LED indicator status charts. Note discrepancies.
- Constant low hum from all | Faulty wiring 1. Check cabinet wiring is correct. speakers. 2. Verify cabinet wiring provides separate wires (not common return) for each speaker.
- Check connection of all cabinet ground wires.
Faulty power supply Use 2-Volt AC setting on digital voltmeter to measure voltages at speaker terminals. Any reading indicates unstable supply that may contain ripple or noise.
Troubleshooting - 17
Miscellaneous Problem Troubleshooting Table
SYMPTOM
- Marquee lamp is intermittent or nonfunctional
- Video Game Machine (VGM) starts and plays normally CAUSE
Faulty fluorescent tube REQUIRED ACTION
Remove fluorescent tube from sockets. If you find cracks or darkened ends, install new lamp. Clean tube. Check continuity of both fluorescent tube filaments. Check lamp ballast is rated for local AC line voltage and frequency. Verify fluorescent tube operates by placing it in working VGM.
Faulty lamp fixture Verify lamp pins make good connection with socket contacts. Check ballast and/or starter are working properly.
Faulty wiring Measure fluorescent lamp AC voltages. Check wiring and connector continuity from AC power chassis to lamp assembly.
+ VGM operates normally
- Cabinet becomes warm after several hours of use Obstructed fan Check bottom and rear of cabinet for blocked airflow. Move VGM away from sources of heat. Turn off power. Remove dust from vent holes with high-power vacuum cleaner.
Faulty wiring Check fan wiring and connectors.
Faulty fan Check operation of all fans.
- Error messages appear on screen
Troubleshooting - 18 Faulty hardware Check any assembly (RAM, ROM, Battery, etc.) identified in error messages. Call your authorized distributor for help with unresolved screen messages.
WARNINGS & NOTICES
- Substitute parts or modifications may void EMC directive or FCC type acceptance.
- This game is protected by federal copyright, trademark and patent laws. Unauthorized modifications may be illegal under federal law. This also applies to MIDWAY logos, designs, publications and assemblies. Moreover, facsimiles of MIDWAY equipment (or any feature thereof) may be illegal under federal law, regardless of whether or not such facsimiles are manufactured with MIDWAY components.
If you or anyone in your family has experienced symptoms linked to an epileptic condition (e.g. seizures or loss of awareness), immediately consult your physician before using any video games.
We recommend that parents observe their children while they play video games. If you or your child experience the following symptoms: dizziness, altered vision, eye or muscle twitching, involuntary movements, loss of awareness, disorientation, or convulsions, DISCONTINUE USE IMMEDIATELY and consult your physician.
COPYRIGHT & TRADEMARK NOTICE You may not reproduce any part of this publication by mechanical, photographic, or electronic means. You may not produce phonograph recordings of this document. You may not transmit this publication or otherwise copy it for public or private us, without permission from the publisher.
CRUIS'N EXOTICA is a trademark of Nintendo. © 1999 Midway/Nintendo. All rights reserved. Manufactured and sold by Midway Amusement Games, LLC. under license. HUMVEE®, HUMMER®, and the VEHICLE GRILL DESIGN are registered trademarks of AM General Corporation. © AM GENERAL CORP. 1999 all rights reserved. FORD TRADEMARKS USED UNDER LICENSE FROM FORD MOTOR COMPANY. CHEVROLET, CHEVY, CORVETTE (1963, 1981 and 1998 models) and VETTE are General Motors Trademarks used under license to Midway Amusement Games, LLC. JEEP and the JEEP grille design, DODGE and PLYMOUTH are registered trademarks of DaimlerChrysler Corporation and are used under license. © DaimlerChrysler Corporation.
For service: Call your authorized MIDWAY AMUSEMENT GAMES, LLC Distributor.
When MIDWAY ships a game, it is in compliance with FCC regulations. The FCC label on your cabinet is proof. If this label is missing or damaged, legal repercussions to the owner or distributor of the game may result. If your game does not have an FCC label, contact MIDWAY immediately.
MIDWAY AMUSMENT GAMES, LLC 3401 N. CALIFORNIA AVE. CHICAGO, ILLINOIS 60618-5899 http:Avww.midway.com
Entire contents of this manual copyright © 2000 MIDWAY AMUSEMENT GAMES, LLC All Rights reserved.