CATHODE RAY TOMES

Turkey Shoot Service Manual (16-3025-101) June 1 1984

Turkey Shoot (prototype) (Williams, 1984) · Manual · 24 pages · 4 sections · original scan

Page 1

16-3025-101 WILLIAMS June 1, 1984

TURKEY sxHooT®

SERVICE MANUAL

For service... WILLIAMS Call your authorized Electronics, Inc. WILLIAMS distributor 3401 N. California Ave. Chicago, IL 60618

Page 2

TURKEY SHOOT ROM SUMMARY

ERROR CODE OR

ROMPART NO.DESCRIPTIONIC NO. BOARD INDICATION
Sound ROMA-5343-107062764 PROM, 8Kx8C8CPUno sound
TURKEY SHOOT 2A-5343-107072732 PROM, 4Kx8Ic9CPUfeathers
TURKEY SHOOT 3A-5343-107082732 PROM, 4Kx8IC10CPUspkr clicks
TURKEY SHOOT 4A-5343-107092764 PROM, 8Kx8IcllCPU213
TURKEY SHOOT 5A-5343-107102764 PROM, 8Kx8Icl2CPU209
TURKEY SHOOT 6A-5343-107112764 PROM, 8Kx8Icl3CPU205
TURKEY SHOOT 7A-5343-107122764 PROM, 8Kx8ICl4CPU201
TURKEY SHOOT 8 = A-5 3343-107132764 PROM, 8Kx8C15CPU214
TURKEY SHOOT 9 = A-5343-107142764 PROM, 8Kx8C16CPU210
TURKEY SHOOT 10 A-5343-107152764 PROM, 8Kx8C17CPU206
TURKEY SHOOT 11 A-5343-107162764 PROM, 8Kx81c18CPU202
TURKEY SHOOT 12 A-5343-107172764 PROM, 8Kx8C19CPU215
TURKEY SHOOT 13 A-5343-107182764 PROM, 8Kx8C21cPU207
TURKEY SHOOT 14 A-5343-107192764 PROM, 8kx8C23CPU216
TURKEY SHOOT 15 A-5343-107202764 PROM, 8Kx81c24CPUnone
TURKEY SHOOT 16 A-5343-107212764 PROM, 8Kx8C25CPU208
TURKEY SHOOT 17 A-5343-107222764 PROM, 8Kx81C26CPU204
Special Chip 2A-5410-10083Special Chip1c29.CPU)==
Special Chip 2.A-5410-10083 = Special ChipIc30.CPU=
Clock-Rom 1A~5282-10295828123 ROM, 32x8 C14VIDEO no video
TURKEY SHOOT 21 A~5343-107262764 PROM, 8Kx8IC41VIDEO vert lines
Horiz-sync ROM 1 A-5282-10294825129 ROM, 256x4 Ic47VIDEO --
TURKEY SHOOT 18 A-5343-107232732 ROM, 4Kx81c55VIDEO gobbles
TURKEY SHOOT 19 A-5343-107242764 PROM, 8Kx8IC57VIDEO vert lines
TURKEY SHOOT 20 A-5343-107252764 ROM, 8Kx8IC58VIDEO vert lines
Decoder-ROM SAA~5282-102926349 ROM, 512x8 IC60VIDEO --

(Horizontal)

CPU-BOARD JUMPERS: Wl, W3, W6, W8, W10, W1l, W14 and W16. Remove jumper W1l for cocktail games.

NOTICE

TO ORDER REPLACEMENT ROMS from your authorized WILLIAMS distributor, specify

  • part number shown above, (2) ROM-label color, (3) REV level (number) on the label, and (4) which game the ROM is used in.
Page 3

Examine your Game

{ INSPECT THE OUTSIDE of the carton or game cabinet for shipping damage.

[]UNLOCK AND OPEN the bottom-rear door. Now check circuitry.

{ JARE CONNECTORS SECURELY ATTACHED? Reconnect any found loose. DON'T FORCE CONNECTORS. They're keyed and only fit one way.

{JARE PLUG-IN CHIPS FIRMLY SEATED in their sockets?

{ JUNWRAP THE POWER CORD coiled inside the cabinet. DON'T PLUG IT IN YET!

( JSCRUTINIZE MAJOR SUBASSEMBLIES, such as the monitor, control panel, transformer chassis and power supply. Make sure they're securely-mounted.

{ ]UNDO THE CONTROL-PANEL LATCHES. You can reach these two from the coin door by extending your arm upward and to either side. Now check connectors and circuitry as above.

Control Locations

//THE_ON-OFF SWITCH is below the back door.

L/TRE POWER-INTERLOCK SWITCH is behind the bottom-right corner of the hack door. The interlock switch is a spring-loaded DPDT type that will turn off the game when you remove the panel. For servicing purposes, pull the switch out and the game will power up.

Z/THE_VOLUME-CONTROL is inside the coin-door and to your right.

Z/TAREE DIAGNOSTIC SWITCHES are mounted together on a bracket behind the coin door. These switches are used to access the Diagnostic-Mode Tests, the BOOKKEEPING TOTALS screen and the GAME ADJUSTMENTS screen.

7 THE MEMORY-PROTECT INTERLOCK SWITCH is behind the coin door. This switch must be open when you clear BOOKKEEPING TOTALS or make GAME ADJUSTMENTS. It automatically opens when the coin door is open.

// TAR CPU-BOARD RESET SWITCH is on the CPU board near the batteries.

// THE CASHBOX ADVANCE SWITCH found inside the cashbox door allows bookkeeping information to be audited without permitting it to be zeroed.

//THE_SOUND DIAGNOSTIC SWITCH is on the CPU board near the small heatsink. Refer to Sound Self-Test for information on its use.

Page 4

=4-

Power Turn-On

WARNING

THREE-WIRE PLUG. This game must be plugged into a properly-grounded outlet to prevent shock hazard and to assure proper game operation. DO NOT use a “cheater” plug to defeat the ground pin on the power cord, and DO NOT cut off the ground pin.

WARNING

FCC STICKER. Check the back of your game to see that an FCC sticker was attached to your game at the factory. All games that leave WILLIAMS' plants have been tested and found to comply with FCC Rules. As the sticker is proof of this fact, legal repercussions to the owner and distributor of the game may result if the sticker is missing. If you receive any WILLIAMS game (manufactured after December 1982) that has no FCC sticker, call WILLIAMS for advice or write us a note on your game-registration card. Be sure the card bears your game's serial number.

WHEN THE GAME IS FIRST TURNED ON general illumination should light. A moment later the scanning "rug pattern" indicating RAM/ROM test should appear on the screen.

IN_A CORRECTLY-RUNNING GAME tests will be followed by the message "INITIAL CHECKS INDICATE ALL SYSTEMS GO." If failure messages come up on the screen instead, refer to Built-In Test Procedures.

DEMAGNETIZE THE GAME with a television degaussing-coil. Besides the monitor, remember to degauss large steel parts (for example, the back-door hinge). Do this as a daily procedure. Otherwise residual magnetism may cause color impurities that adversely affect your collections.

Game Operation

GAME START

INSERT COINS. The game allocates an adjustable number of credits per coin and displays this number on the CRT. Factory settings are one credit for two quarters. At factory settings, when two credits are displayed, pressing 2-PLAYER START initiates a two-player game.

PLAYER CONTROLS

//s800 mischievous turkeys with the laser gun.

/7PRESS GOBBL Freeze the turkeys and pick them off with the gun!

/7PRESS GRENADE! #liminate several turkeys in one blast!

GAME PLAY

WITH A HAND ON HIS GUN, his GOBBLE and GRENADE buttons at the ready, the player defends his territory from marauding TURKEYS! He's given 100 missions to eliminate all the turkeys.

Page 5

HE CAN TAKE AIM with his laser gun using the cursor on the screen to home in on his enemies. Or he can launch a GRENADE to blast all turkeys within range. Once each mission he can activate his GOBBLE button to momentarily freeze all the turkeys.

ASTUTE PLAYERS learn that most turkeys can be eliminated by a shot to the body. However the cyborg mechano-turkey persists until they hit him in the head. No turkey will succumb to a shot in the leg!

MISSIONS REQUIRE QUICK REACTIONS to clever ploys such as turkey air-raids, turkeys disguising themselves as businessmen and turkey helicopter-getaways. Every 8th wave earns a rapid-fire bonus where the player has 15 seconds to eliminate as many turkeys as possible. The player can score bonus points by shooting fire hydrants and trashcans as well as by freeing hostages.

THREE FOWLUPS are allowed. These occur whenever a turkey escapes or when an innocent bystander is injured.

Bookkeeping Totals

BOOKKEEPING TOTALS SHOW YOU AT A GLANCE if game settings are bringing you a satisfactory return on your investment! Only games by WILLIAMS ELECTRONICS have this feature. Think of it as a unique way to keep your TURKEY SHOOT game the leader of the pack when it comes to earnings...location after location, week in and week out!

AUTO-UP O@O HIGH MANUAL. ADWANCE SCORE DOWN RESET

Diagnostic Button Switches

ENTERING BOOKKEEPING MODE. Inside the coin door is a bracket with three button switches, Set the AUTO-UP/MANUAL-DOWN (center) switch to AUTO-UP. Press the ADVANCE switch to display BOOKKEEPING TOTALS on the screen. Now check those totals. Here's what to look for...

BOOKKEEPING TOTALS

LEFT SLOT COINS 432 CENTER SLOT COINS 0 RIGHT SLOT COINS 398 PAID CREDITS 830 EXTRA MISSIONS EARNED 226 TOTAL PLAY TIME [HOUR: MIN] 34:28 TOTAL MEN PLAYED 689 TOTAL SINGLE PLAYER 548 TOTAL TWO PLAYER 141 TOTAL CREDITS PLAYED 830 AVERAGE TIME /GAME [MIN:SEC] 2:00

Bookkeeping screen

Page 6

AVERAGE TIME PER CREDIT: TWO MINUTES. Your most important figure on the BOOKEEEPING TOTALS screen is AVERAGE TIME/GAME. You'll want to pay special attention to this figure every day for this reason: Thorough field and factory research has shown that two-minute games both satisfy players and also keep the quarters flowing.

If games aren't running about two minutes long, then collections probably aren't at their peak. You'll want to tailor your game to your game-playing public. It's easy. But only WILLIAMS games let you do it!

GAME ADJUSTMENTS

EXTRA FOWL EVERY 50000 RECOMMENDED MISSIONS FOR 1 CREDIT GAME 3 RECOMMENDED ATTRACT MODE SOUNDS YES PRICING SELECTION 5 1/PIFTY 2/DOLLAR LEFT SLOT UNITS 1 CENTER SLOT UNITS 4 RIGHT SLOT UNITS 1 UNITS REQUIRED FOR CREDIT 2 UNITS REQUIRED FOR BONUS CREDIT 0 MINIMUM UNITS FOR ANY CREDIT

DIFFICULTY OF PLAY Ls RECOMMENDED

GUN RECOIL YES RESTORE FACTORY SETTINGS NO CLEAR BOOKKEEPING TOTALS NO HIGH SCORE TABLE RESET NO AUTO CYCLE NO

[PLAYER 1 START] TO MOVE UP - [PLAYER 2 START] TO MOVE DOWN (GOBBLE] TO INCREASE VALUE - [GRENADE] TO DECREASE VALUE

PRESS ADVANCE TO EXIT

Adjustments Screen Showing Factory Settings

Exclusive Game Adjustments

  • Inside the coin door is a bracket with three button switches. Set the AUTO-UP/MANUAL-DOWN (center) switch to AUTO-UP.
  • Press the ADVANCE switch twice. The GAME ADJUSTMENTS screen will come up.
  • Use PLAYER 2 START to move down to the desired adjustment.
  • Use PLAYER 1 START to move up.
  • Use GOBBLE (raise value or yes) or GRENADE (reduce value or no) to alter the value of an adjustment.
Page 7

Now for the multiple-choice section! Choose one or more:

//Sse GOBBLE or GRENADE to choose the appropriate difficulty level (0 = easiest or extra liberal, 5 = average, 9 = hardest or extra conservative).

Z/SELECT GAME PRICING with standard or custom settings. See the Pricing Table later in this chapter.

Pricing Table

Units Min. Units Req'd Units Left Center Right Req'd For Por Coin-Door Pricing Slot Slot Slot For Bonus Any Mechanism Games/Price Selection Units Units Units Credit Credit Credit

Twin Quarter 1/254, 4/$13141100
Quarter,1/25¢, 5/$1014114O
Dollar,2/50¢, 4/$101411Q2
Quarter2/50¢, 5/$10141142
@1/50¢, 2/$15141200
1/50¢, 3/$1, 4/$1.25 031234150
1/$10141400
1/50¢, 3/$1, 7/$2i)124812149624
1DM, 5DM2/1DM, 12/5DMa12it)2200
@1/ipM, 6/5DM26011')i)
1 Franc,@1/2F, 3/5F only411662it)ti)

5 Franc

25-Cent,01/25¢, 4/1G610ry100
1 Guilder1/25¢, 5/160ii)414oO
5 Franc,@1/5F, 2/10F7102100
10 Franco1/10F81i}220it)
1 Franc,e2/1F, 5/2F26i)1100

2 Franc

100 Lire,1/200 Lire8102200

200 Lire

Twin Coine@1/l Coin3141100
e1/2 Coins5141200
1/4 Coins01414it)it)
1/2 Coins, 3/4 Coins 1141240
1/3 Coins, 2/5 Coins 02025i)it)
1/2, 3/5411662i)0
1-Unit,1/1, 5/50105100
5-Unit1/3, 2/50201050i)
AnyeFree Play914110Q
Page 8

Game Pricing

PRICING SELECTION allows a shorthand method of setting the pricing functions. If a number from one to nine is entered into the PRICING SELECTION function, a corresponding standard setting (shown in the pricing table above) will be entered into the game. The rest of the pricing functions are automatically set for that standard.

FOR CUSTOM SETTINGS first set PRICING SELECTION to zero. Then set the remaining values according to the Pricing Table.

THE GAMES : PRICE RATIO is equivalent to the ratio 3 VC where: X = SLOT UNITS V = COIN VALUE C = UNITS REQUIRED FOR CREDIT

For example at factory settings with quarter chutes the variables produce l : 25x2 or one game for two quarters.

Diagnostic-Mode Tests

SET THE AUTO-UP/MANUAL-DOWN SWITCH to the MANUAL-DOWN position and press ADVANCE. The game is now in its Diagnostic Mode and a ROM test is performed. With ROM test results present on the CRT display, set the AUTO-UP/MANUAL-DOWN switch to the AUTO-UP position. Enter subsequent tests by pressing ADVANCE once more for each test. After the last test, Game-Over Mode commences.

AUTO-CYCLE MODE permits continuous ROM, RAM and CMOS RAM tests to detect failures that only appear after numerous checksum comparisons. If an error is detected Auto-Cycle Mode is aborted and a failure message is displayed on the CRT.

  • Open the coin door. It must remain open for AUTO CYCLE.
  • Display GAME ADJUSTMENTS.
  • Move down to AUTO CYCLE. 4, Display YES.
  • Press ADVANCE.
  • To enter Game-Over Mode turn the game off and on.

Built-In Test Procedures

POWER-UP TESTS

RAM TEST. A rug pattern scans across the screen. Only screen RAMS (dynamic type) are tested. A bad RAM is indicated on the CPU-board LED-indicator by an error code between 100 and 199 (eg., 1-3-1; see the table of Screen-RAM Error Codes below). If a RAM error is indicated, check all three DC power-voltages on the RAM indicated: -5/pin 1, +12/pin 8, +5/pin 9. None of these should have more than a few millivolts of AC on it. Never replace a RAM chip until you prove that these voltages are normal:

Page 9

Screen-RAM Error Codes

CHIP 98 99 100 101 102 103 104 105 CODE 115 116 117 118 lll 112 113 114

CHIP 106 107 108 4109 #110 211 112 113 CODE 125 126 127 128 121 122 123 124

CHIP 114 115 116 117 118 119 120 121 CODE 135 136 137 138 131 132 133 134

ROM TEST. A bad ROM is indicated on the CPU-board LED-indicator by an error code between 200 and 299 (eg., 2-1-1; see the ROM Summary for codes). An error message may also appear on the CRT. Power down and replace bad chips.

CMOS-DATA TEST. Checksums are compared. If the CMOS RAM fails the test, FACTORY SETTINGS RESTORED appears on the CRT.

DIAGNOSTIC-MODE TESTS

RAM_AND ROM TESTS... These tests are repeated, only the ROM test is performed first. Refer to RAM Test and ROM Test above.

CMOS-RAM TEST. A chip error is displayed on the CRT and the LED readout on the CPU board. I£ the CMOS RAM is bad, the error code 3 will appear on the LED readout.

SOUND, COIL AND LAMP TEST. Sound-lines 1 through 6 are tested. In addition, the grenade and gun lamps, feather and gun coils are checked. One by one, sound lines, lamps or coils are pulsed. When a sound line is pulsed, its number is shown on the CRT. You should hear a separate sound for each sound line. If a sound is missing, its corresponding line is stuck high (that is, open) or stuck low (that is, shorted to ground). If two lines produce the same sound, they're shorted together. Use AUTO-UP to cycle through all the sounds, coils and lamps. With MANUAL-DOWN, you'll continuously test one sound-line, lamp or coil.

SWITCH TEST. The name of the switch is highlighted when that switch is closed. Opto switches (used to determine gun position) are tested in a special way: Watch the graph on the left side and bottom of the switch-test screen as you move the gun. The graph should change color ("move") smoothly. If the graph appears to "jump," adjust the optos for smooth movement. To exit the switch test you must hold ADVANCE down until the next screen appears.

THE CROSSHATCH PATTERN aids the technician in converging the monitor.

THE PURITY SCREENS (solid red, green and blue screens) are intended for monitor adjustments and for checking the color RAMS. If these screens show contaminated colors, degauss the screen and adjust the purity magnets. If colors are missing, one of your color RAMs may be bad. A purity screen with vertical lines through it also signals a color-RAM error. (Please don't confuse the purity screens with the crosshatch pattern or color bars pattern. These test patterns are supposed to have vertical lines!)

Page 10

THE COLOR BARS are intended for monitor adjustments and for checking the color RAMS. The bars serve as a color and brightness reference when you adjust the color drives and cutoffs, screen and black-level controls. If colors are missing or the wrong colors are displayed, you may have a bad color RAM. From the left side of the CRT, here are the colors you should see: red, green, blue, black, white, yellow, cyan and magenta.

Sound Self-Test

  • NO_SOUND_IN DIAGNOSTIC-MODE TEST: Check the sound-select inputs (pins 2 through 9 of IC 4) on the CPU board for pulsing during the test. Also check for shorts between sound lines.
  • STILL NO SOUND: Turn the volume control all the way up. With the game turned on, momentarily place a powered-up AC soldering-pencil on the center tap of the volume control. DO NOT use a soldering iron of over 40 watts. Cordless models will NOT work here.

(A) If you hear a low hum, the power-amplifier chip (TDA2002A), volume control and speaker are okay.

(B) If you don't hear a hum, try the test again with the volume control turned halfway up.

  • GARBLED SOUNDS: One at a time, replace microprocessor IC27 and Sound Rom IC8 on the CPU board.
  • THE SOUND DIAGNOSTIC BUTTON on the CPU board isn't used in this game. If you accidentally press this button, game sounds will be disabled until you turn the game off and on again.

TURKEY SHOOT Circuitboards & Gun Mechanism

PART NO. DESCRIPTION

¢-10525 opto PC-board C-8809 heatsink assembly D-9444 or D-8784 power-supply PC-board

D-9868 video PC-board D-9886 power-transformer chassis D-10395 CPU PC-board

D-10413 interface PC-board D-10289 gun-mechanism SFL-24-750-pc gun coil-assembly SFL-25-750-DC feather-dispenser coil

Page 11

=-ll-

Warnings & Notices

WARNING

FOR SAPETY AND RELIABILITY, WILLIAMS does not recommend or authorize any substitute parts or modifications of WILLIAMS equipment.

USE OF NON-WILLIAMS PARTS and modifications of game circuitry may adversely affect game play, or may cause injuries.

SUBSTITUTE PARTS OR EQUIPMENT MODIFICATIONS may void FCC type-acceptance.

SINCE THIS GAME IS PROTECTED by Federal copyright, trademark and patent laws, unauthorized game-conversions may be illegal under Federal law.

THIS "CONVERSION" PRINCIPLE ALSO APPLIES to unauthorized facsimiles of WILLIAMS equipment, logos, designs, publications, assemblies and games (or game features not deemed to be in the public domain), whether manufactured with WILLIAMS components or not.

WARNING

This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to correct the interference,

RF-INTERFERENCE NOTICE

CABLE PLACEMENT and ground-strap routing on this game have been designed to keep RF radiation and conduction within levels accepted by FCC regulations.

TQ MAINTAIN THESE LEVELS, reposition harnesses and reconnect ground straps to their original placements if they should be disconnected during maintenance.

"TURKEY SHOOT" is a trademark cf Williams Electronics, Inc.

©1284 Williams Electronics, Inc.

Page 12

PIN

WHITE wires

ITEM

eR woh Vewne

FOowar HV eUONne a12<

TURKEY SHOOT GUN ASS'Y. (D-10302

PART NO. DESCRIPTION

03-7890 GUN, MOLDED B-10293 GUN SHAFT ASS'Y 03-7891-24 GUN NOZZLE C-10423-3025-1 3025 BIN ASSY GRND 4106-01099-16B S.T.S. #6 TORX (T-15) TRX-PH 4106-01099-18B S.T.S. #6 TORX (T-15) TRX-PH 4106-01099-06B S.T.S. #6 TORX (T-15) TRX-PH 4106-01099-26B S.T.S. #6 TORX (T-15) TRX-PH 03-7786 P/GRIP TRIGGER 01-7994 T/S TRIG. SPRING 5647-10163-00 TRIGGER SWITCH 8-10328 GUN CABLE 4106-01009-06 SMS #6 x 3/8 P.PH P A-10512 SKT. & BULB #1866 ASSY. A-10441 COIL BRKT SUB-ASSY 01-7991 T/S COIL RET BRKT 02-4211 T/S KICKER PLUNGER 10-257 SPRING-CREDIT BTN SPL-24/750-pC 3025 GUN COIL ASSY 23-6557-9 NEOPRENE GASKET 5791-09138-00 9P1625 03-06-2092 RM- 23-01 H.S. TUBING 1/8 POLY

9-PIN MALE CONNECTOR

COLOR FUNCTION

ORG-BLK 22 SW. GND ORG-BRN 22 TRIGGER SW. ORG-RED 22 GRENADE SW. BLK-RED 22 LAMP COMMON 6V D.C. BLK-RED 22 TRIGGER LAMP ON-OFF BLK-ORG 22 GRENADE LAMP ON-OPF BLK-YEL 18 TRIGGER SOLENOID ON-OFF BLK-BLU 18 SOLENOID COMMON (+12V D.C.) NoT USED

HOUSING 5791-09138-00 (REF.). Install item 21 after are installed in gun shaft.

FEATHER CHAMBER ASSY. (D-10344)

PART NO. DESCRIPTION

11-768 FTR DEVICE FRAME 01-7906 F/D GLASS CLAMP 4206-01016-08 WS #6 x 1/2 P-RH 03-7902 FTR DEVICE SCREEN 4208-01041-10 WS #8 x 1/2 P-FH 01-7927 FEATHER GUIDE 01-7979 F/D FLOW DIVIDER 31-1228-3025-U 3025 F/D COVER 08-7424 FTR DEVICE GLASS 20-9435 FEATHERS 23-6573-4 NEOPRN GSKT 17" QTY.

One Ree

D e een

Page 13

CPU BOARD

rr erry

fore | [rere | fers | rT Law]

[exe] [c] [ewe]

Circuitboards & Gun Mechanism

CONNECTOR KEY _

1 CPU BOARD7 CONTROL PANELeeeenON
2 VIDEO BOARD8 COIN DOORporeopto PC-Docee! subarsembty
3. INTERFACE BOARD9 CASH BOXoeheatsink cssernioyy
4 POWER SUPPIY10 VERTICAL OPTO-BOARD+
5 MONITOR11 HORIZONTAL OPTO-BOARDLallias__ |" Powersupply PC-board
6 CABINET12 GUN0.9868video PC-board

0-9886 Power-transformer chassis D-10395, _ CPU PC-board 7 j b-40413 interface PC-board j 0-10289 gun mechanism ‘SFL-24-750-DC gun coil-assembly | SL-25-750-DC featherdispenser coil

Page 14

Fe Gi EER UF sean ct) —~ am S co) Coe Ics [ep TB ce oe: coc ay cocees sah ten # x88 | Bi ° Se

Page 15

ig a8 gasegaoedt ath

4] oe x? Ria oo & f i ie

18 4 oF i 7 Fo rege 9 re

SERRE GATES. ee cI

wear [yt 3a en ea fear Pe oe cae Se

Page 16

apteeett

wages ce. aca

B 12203 “119M ce Pi 34 ; y 4 3 5 8

He

2] &§ ¥

=r oN WILLIAMS ELECTRONICS, INC. crn carom wv “oacngo oe "SCHEMATIC, CEU PSoearic ce [Zs [ezoel"™ 1-902 F4

Page 17

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 18

> ‘o B cess Coms § ood |

: p Cactoms cos § cn coms ams oom © cess $cc = cosh

Coz § com Cis coras § Cs) Coe

=a) i =

eed ' na qa ek 0 See rch F + 7 7 Ee] ATTIRE TOOL CHUL

a

oh NC | LY S|

Page 19

Hi 38] SER

EREQERE

a ane se aaa @ [aa 8? wae

we fom dae

aCe moe

EN eel Ed Seo eae ert Letitia Teaoe

$ é

ata OHEMATI [—ranrmnnen [aso ca WILLIAI IS ELECTRONICS, INC. & VIDEO. ae bl

Page 20

: = Ryepiente ; lees

SS

Hest Paros

7 Ef

ct i. a6 1C97 9 i. 0 Ole eee che ie, Sie ek

i

Mite Rarer ro

BYPASS_CAPS INGEST Sect i SRP TS —T— ces TWILLIAMS ELI ECTRONICS, cena,

Page 21

@ socarion semonmare

© \ freceook fococcensh poceeowesh °

HRT | 6 H

4 jc | O|ececctece

1 FOR SCHEMATIC. REFER TO OROWING MO. 16-8918. 2 MESISION, 4.7K) Ale Re AG ATs RIB RID. APPLY ITER 33. BETWEEE TEMS 7 295 aacto0 = 82 HEX HUT Tang

RESISTOR, oF log

D

@ puma | Ee orn 2's vatwart | 2 a 1

  • 1

a 2

Fu Fe 2

a 4

eyes €6,¢7(° * [ei ft, BL, Py So feo. tev */-ine aaa [eo bapematmyaen (eae. ELECT. Wb, cs co | oe’ neo, sev"ese-t0r| 2

vadRESESTOR. Ce7

fae 7 [sie RESISTOR CF,

4 |go1ts-e0fs| Sse omn se i7a varr | #

Ela RESISTOR CF

13 |g0776-00ne| oe cent174 vant | 1

oie RESISTOR CF. 12 [eseze-ee | RS RO | Seger sy irs varr | 2

1feiRESISTOR CF7

feat sy 1/4 vant RESTSTON. CF. oeow se 17s vert | &

>“TeanSTSTOR2

Begia2 NN

-yTRERSTSTOR,Fy

ad

=TRSSTSTOR=

Bara

© (8%oerPBTBGE RECTIFIER.|"

sese-20 SR on sees Fee

ssack Shes [170 orien on 963
7rrEAC)7

Gis" wee everrer. Lee 712s

3Ceer4

TC. FaSiST

£ve us[ii 2710 tex

Ber PL. BORD

Page 22

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 23

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 24

wesbe1g o1peway. > pseog Ajddng Jemog 818-0

MOUNTED ON HEAT SINK

WF The iB Ess THAN ¢4.9ayoe REMOVE H10, ie Trt os ati. Less Tuan 4.9000, THEN Ghecx pmecisiou mesisTOns nea Red, IF ‘ney ARE yeTWin THE TR TOLERANCE Tren Greek tee. +83v0c

OURTEO ON HEAT SIR . 2N3055, 1

s2eevoc save

erm bt

nore: cee hoa ‘W118 NOT USED On UP mn OAM Bae wbancncr oe, Tha teow 2 ty

3 taavoe ne

>] 3 9270 unaea,