Kram
Kram (rev 1) (Taito America Corporation, 1982) · Manual · 54 pages · 15 sections · original scan
Uraite/ ©1982 Trade Marks of Taito America Corporation 72-00017-001 _
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

This page is a drawing, shown as the original scan.
LIST OF ILLUSTRATIONS
Figure 1-1 Programming Plug...............0.....08 6
Figure 1-2 Power ON/OFF Switch............0...... 7
Figure 1-3 Interlock Switches & Memory Protect Switch... 7
Figure 1-4 Self Test Switches..........00........0... 7
Figure 1-5 Volume Control Setting.............2..... 7
Figure 1-6 Door Switches
Figure 1-7 Video Board (On Back of Service Door)....... 9
Figure 1-8 FlowChart..........0. 0.0.0... eee 10
Figure 1-9 ColorBar.............. 0... c eee eee eee 10 Figure 1-10 Color Bar... 2.0.0... eee eee eee "1
Figure 1-11 ColorBar.... 00.2... eee if]
Figure 2-1 Coin Door.......... 26... eee eee ee 16
Figure 2-2 Fuse Replacement. .
Figure 2-3 Monitor Removal....................005 16
Figure 2-4 Cover Glass Removal.................... 7
Figure 2-5 Printed Circuit Board.................... 17
Figure 2-6 Power Supply................2...00005 7
Figure 2-7 Current Limit Adjustment................ 18
Figure 3-1 Clock Timing................. 000000005 22
Figure 3-2 Dual Port RAM Timing LIST OF TABLES
Table 1-1
Table 1-2
Table 1-3
Table 1-4
Table 1-5
Table 1-6
Table 1-7
Table 1-8
Table 1-9
Table 1-10
Table 2-1
Table 2-2
Table 2-3
Table 3-1
Table 3-2
Table 2-3 Self Test Switches
Hardware Tests...... 0.0... 8
Video Board ROM Checksum............... 8
Decoding Jumper Location................ 8
Video Board RAM Checksum............... 9
Data/Sound Board ROM Checksum.......... 9
Screen ROM Content.................0.. 10
Audit Totals... 2... ee 12
Standard Coin Setting...............0... 13
Custom Coin Setting... 0.0.0.2... eee 13
Line Voltage... 0... eee. 17
Secondary Fuses
Video Board Test Points................... 19
Video Board Memory Map................ 22
Register Initialization.................... 23
Data/Sound Meory Map................. 24
Game Set-Up
1.8 SELF TEST PROCEDURE 1.8.1 GENERAL : The Self Test Procedure is performed using the two(2) Switcht located on the inside of the Coin Door, and the Self Test Button and the LED’s on the Video PC Board. (See Figure 1-6).
FIGURE 1-6 DOOR SWITCHES
1.8.2 ENTERING INTO THE SELF TEST MODE To enter the Self Test Mode, press the Advanced Sub Test Switch on the Coin Door or the Self Test Button found near the LED display. All the LED's should blink on and the Hardware Tests should start. The Diagnostics can be entered at the Location Programming Screen (Section 1.8.16) by pressing the Advance Test Switch on the Coin Door. If a continual test of the Video Board is desired, press the Self Test Button twice to start the Video Test in the Auto Test Mode. In this mode, the machine will continually run the Hardware Test until powered off. If the message ‘‘OPEN COIN DOOR TO TEST"’ appears the’ Coin Door must be opened or a jumper connected across J19, 1-2. This is because the CMOS RAM Test (Section 1.8.6) cannot be performed with the memory protected by the Coin Door Switch.
1.8.3 HARDWARE TESTS These tests are performed in the following order: VIDEO BOARD DATA BOARD ROM Checksum ROM Checksum Communications RAM Local RAM Communications RAM Handshake Test CMOS RAM Color RAM Screen RAM TABLE 1-2 HARDWARE TESTS
All LED Values are shown Left to Right, 0 if OFF, 1 is ON and X is dependent upon the test results. 1.8.4 VIDEG BOARD ROM CHECKSUM The ROM Checksum calculates the Checksum of each Video ROM and compares it to the Checksum stored for that ROM. If it differs from the stored value, the machine will halt and the Value of the ROM with the bad Checksum will be shown on the LED'S.
LED VALUES: TESTINPROGRESS 000001 FAILURE: 01 XXXX LED VALUE VIDEO
01 0000 A000-A7FF 01 0001 A800-AFFF 01 0010 BO00-B7FF 010011 B800-BFFF 010100 C000-C7FF 010161 C800-CFFF 010110 D000-D7FF 010111 0800-DFFF 01 1000 £000-E7FF 01 1001 £800-EFFF 01 1010 FO00-F7FF 011011 F800-FFFF
TABLE 1-3 VIDEO BOARD ROM CHECKSUM
If the Checksum ROM is bad, it will show U10 to be bad first. If this test fails, the ROM indicated on the LED display will need to be replaced. The E-PROM Memory in a given game may be implemented as banks either 2716 or 2732 E-PROMS. The E-PROM type for each bank is selected by the decoding jumper 26-00002-016 or 26- 00002-032.
LOCATION ul E-PROM BANK
U22 U29 TABLE 1-4 DECODING JUMPER LOCATION
1.8.5 COMMUNICATIONS RAM FROM VIDEO BOARD The Communications RAM Test determines the stability of memory shared by the two processors by storing a predefined series of numbers throughout the RAM, then reading it back to insure that it was stored correctly.
LEDVALUE 000010 A failure has been detected when the machine halts with the above display. Failure of Communications RAM during Video Board Tests May result from either defective RAM circuitry or failure of the Data Board. To isolate the failure, disconnect the Data Board at P6 and reenter the Test. A failure means trouble in U3, or U4 or associated circuits. Passing the retest suggests Data Board problems.
1.8.6 VIDEO BOARD CMOS RAM After saving values in another protion of memory, the CMOS RAM is tested in the same manner as the Communications RAM. If the CMOS RAM passes the test, all of the locations are restored to their previous values. LEDVALUE 000011 A failure of the CMOS RAM has been detected when the machine halts with the above LED value displayed. If this occurs U85 and U86 or associated decoding should be checked.
1.8.7 VIDEO BOARD COLOR RAM This tests the system Color RAM by storing predefined sequences of numbers in the Color RAM, then reading them back while testing for accuracy. LEDVALUE 000100 A failure is indicated by the Processor halting with the above value displayed on the LED'S. This signifies the need to check U56, U57 and associated multiplexing and decoding.
The Screen RAM is tested by writing a pattern to each page on the screen. The results of these writes is then compared to the original pattern. Any discrepancy causes the machine to halt with the LED displaying the faulty RAM. LED VALUES: TEST IN PROGRESS 000101 FAILURE 1X XXXX
LED VALUE 14 XXXX
10 0000 11.0000 10 0001 11.0001 10 0010 110010 10.0011 110011 10 0100 110100 100101 110101 100110 110110 100111 110111 10 1000 11 1000 10 1001 111001 10 1010 111010 101011 111011 10 1100 111100 101101 111101 101110 111110 101111 444111 TABLE 1-5 VIDEO RAM CHECKSUM
Upon failure of a Screen RAM, locate the problem RAM and replace it. Exchange the suspected RAM with a known good location to determine if the problem moves with the RAM, IC or whatever the problem is in the supporting circuitry. Further testing can be done with the Color Bar Test. If this Diagnostic appears to halt without indicating a RAM failure (00 0101 on LED'S), a failure to begin the next test (Data Hardware) is indicated. The interconnection to the Data Processor must be in place and the Data Processor must be functional to continue.
SELF TEST LEDS
oo 0000
SELF TEST BUTTON
FIGURE 1-7 VIDEO BOARD (ON BACK SERVICE DOOR)
1.8.9 DATA/SOUND BOARD SELF TESTS DATA HARDWARE (ROM CHECKSUM) The ROM Checksum calculates the Checksum of each Data ROM and compares it to the Checksum stored for that ROM. If it differs from the stored value, the machine will halt and the value of the ROM with the bad Checksum will be shown on the LED'S. LED VALUES: TEST IN PROGRESS 00.0110 FAILURE 01 XXXX 010000 01 0001 01 0010 010011 010100 010101 010110 010111 01 1000 01 1001 011010 011011 TABLE 1-6 DATA/SOUND BOARD ROM CHECKSUM If this test fails in the field, the bad ROM will need to be replaced.
1.8.11 DATA/SOUND BOARD LOCAL MEMORY The Data Processor uses a known sequence of numbers to test the bits in its local memoray. If a bad bit is found the machine will halt with the following display. LED VALUE: 000111
1.8.11 COMMUNICATIONS RAM ADDRESSING The function of this test is to ensure that both the Data and the Video Processor address the Communications RAM in the same manner. The Data Processor requests the Video Processor to fill the RAM with a known pattern then, the Data Processor compares the Tesults to the expected pattern. If it does not match one of the Processors is probably decoding the address incorrectly as the RAM itself was previously tested for stability by the Video Processor. The machine will halt with the following display. LED VALUE: 00 1000
1.8.12 DATA/VIDEO HANDSHAKE This test ensures that the Data Processor can send priority commands via interrupts to the Video Processor after the proper command acknowledgements are received. The machine will halt with the following display. LED VALUE: 00 1001
1.8.13 SWITCH TEST This Screen is used to determine all Switches are in working order before entering the switch dependent self-test screens. The Wiring Diagram supplied with each game will indicate the number associated with a particutar switch. The switch number appears in green if the switch is closed and white if it is open. The Advance Test Switch (Switch Number 9) is always RED in order to set it apart from the other switches on the screen. Switches 29, 30, 31 and 32 are not used and remain green. The user should check all other switches before pressing the Advance Test Switch, as this would move him to the next screen. In addition to the switches required, by the game, the User should be sure to test the Advance Sub Test, UP and DOWN Switches located in the Coin Door for proper closure as the switches are used to move about in the Self Test Screens. To advance to the next screen, activate the Advance Test Button on the Coin Door
SCREEN RAM CONTENT COLOR RAM ADDRESS
BINARY BIT TESTED GAME OVER Red 0000 0001 Orange 0000 0010 Yellow 0000 0100 Green 0000 1000 Blue Green 0001 0000 Blue 0010 0000 ADVANCE
ROM cHEcKsuM[_00 0001—G1 XEXx
COMMUNICATIONS RAM Y 00 0010
ADVANCE TEST
| Violet | 0100 0000 | wioeo | naw | Y 00 0011 |
| White | 1000 0000 | Bonne | ontovon nea Y os 8100 | |
| oft | ' M1 " 0 | seacen naw) | 00 010172 RE Hs |
range Yellow 41111011 auuge iia en fom nec { no eS
| Green Blue | 41101411 | FEET | commmennone Dery ov too | { |
Blue 11011111 Violet 10111111 White 01111111
Black XXXX XXXX
TABLE 1-7
TABLE 1-7 SCREEN RAM CONTENT — COLOR RAM ADDRESS HANDSHAKE TEST } 00 1004 NONSOMBAONaMAOWWA® ‘SwiTcH TEST GRAY SCALE COLOR BARS. ALIGNMENT CONVERGENCE LANGUAGE SELECT LOCATION PROGRAMMING Yq——————_¢ HIGH SCORE TO DATE AuDIT TOTALS, COIN SLOT PROGRAMMING SCREEN TESTS |
GAME OVER 1.8.14 COLOR BALANCE AND INTENSITY ADJUST SCREEN This screen is comprised of two sections. The first section provides a method for adjusting the intensity level of each color gun, FIGURE 1-8 FLOW CHART and achieving an initial color balance. Three squares, one blue, one green and one red, are drawn along the top of the screen at maximum intensity and brightness. The color guns should be adjusted so that these squares are barely visible and equal intensity. To complete the color adjustments, a gray scale is provided at 50 0 © 0 0 ’ : ide é 9.2 gh NR RN the bottom of the screen. Fine tune the color balance with this IIE SCC IC ICONS scale, then double check that the squares at the top are barely Meer ooP > PNP cOasahindan® organs
| visible. To advance to the next screen, activate the Advance Test | SOOFF | SSS | OT AN A | NS | secre |
Switch located on the Coin Door.
1.8.15 COLOR BARS The CPU divides the screen RAM into 16 areas corresponding to 16 bars on the screen. Each area is written with a data value from the Table below. Each value exercise one bit in the Screen RAM. The Color RAM is written with a pattern which outputs each data value with a recognizable color from the Table. All other data values are coded in black. This results in a normal screen of 16 color bars per the following table.
COLOR BAR DIAGNOSTIC NORMAL
FIGURE 1-9 COLOR BAR (NORMAL)
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
are ruled out. This leaves latches U91, U96 and U105-109, direction select U81 and U104 and the CR side of the Color RAM MUX U55, U73 and U74. Stuck bits may be identified by observing abnormal bars. A bit stuck high will result in black bars (two bit high) on the left or top half of the screen except for the bar associated with the stuck bit will be black. The converse is true of a bit stuck low. An error across the entire bar indicates an error in the shift registers, direction select, or color RAM MUX which affects every pixel. Lines of error running crosswise to the bars indicates an error in one bank of RAM of every eighth pixel. To move to the next screen, activate the Advance Test Button. It self test fails, the Color Bars still may be useful. This screen may now be entered without going through on-board self test. Use ‘‘Advance Test’’ to enter the High Score Screen then ‘‘Down’’ to enter the Switch Test. Advance Test may then be used to access the Color Bars.
1.8.16 ALIGNMENT AND CONVERGENCE TEST This screen is provided to align the color guns and correct the convergence on the screen. The screen is composed of a red and green rectangle and white grid. Adjust the screen width and length so that the red rectangle is slightly within the boundaries of the tube. The adjustment is to be Made on the center of the lines which make up the rectangle. The corners of the rectangle will extend beyond the shadow mask. The green rectangle defines the normal playfield and so should be visible from the players view point. A grid of which squares is provided to help detect and correct any convergence problems the tube may have. Adjust the monitor until the squares are of equal size throughout the screen. To advance to the next screen, activate the Advance Test Button on the Coin Door.
1.8.17 LOCATION PROGRAMMING SCREEN (LANGUAGE SELECTION) This screen allows the user to select the language in which the Location Programming and the game will operate. Four (4) languages are provided. Use the Advance Sub Test Button to move through the offered languages. When the desired language is green, depress the Advance Test Button, to advance to the next screen.
1.8.18 LOCATION PROGRAMMING This screen allows the location to define the difficulty factor for the game. It also allows the location to set a maximum number of credits allowed in the machine prior to a game start up. The user selects the line to be changed by using, the Advance Sub Test Button until the desired fine is changed to green. The value associated with this line is then modified with the UP and DOWN Switch. If the machine is to be reset to the factory settings, use the Advance Sub Test Button until the reset line is lit in green, then press the UP Switch. The values will be reset and the user will be placed back on the first line for further adjustments. Advance test will move to the next screen at any time. The maximum credits defines a limit for the machine, which when crossed will disable the coin slots. This allows the location to set a limit on the amount of games a player will get if there is a line of people waiting. This value ranges from 1 to 99. However, it should not be set so close to 99 that a single coin can overflow the credits issued (maximum 99). A Free Play Mode may be selected by setting Maximum credits to 0. The credits per coin slot are set in the coin slot programming screen. This screen shows the scores and initials of the players with the te highest scores. It is used as an audit for the game. To reset tt values to the backup HSTD selected on the previous screen, pres the UP Switch. This will also set the initials to “‘TAC''. When the UP Button is activated it resets to default scores. To mov to the next screen, activate the Advance Test Button on the Coi Door.
1.8.20 AUDIT TOTALS The screen provides the audit totals for the game. Once they ar recorded, they may be zeroed by pressing the UP Switch. The fol lowing audits are kept.
The total number of paid credits issued. This total is never zeroed, but it will wrap around to zero when its total reaches 1,000,000. The only time this total can be zeroed is by physically removing the battery or jumper W1, while the power is OFF. Total Credits
Left Coins The number of coins dropped into the left slot. Center Coins The number of coins dropped in the center slot. Right Coins The number of coins dropped into the right slot. Paid Credits The number of credits issued for coins. Awarded Credits The number of credits awarded by the game. % Free Plays Awarded Credits/Paid Credits + awarded credits. *100 Minutes Played Number of minutes the game has been in play mode. Minutes Awarded Number of minutes the game has been in extended or awarded play. % Free Time Awarded minutes/minutes played *100. Average Game (Sec) | Minutes played/paid credits + awarded credits *60. The number of times which a player scorec high enough to bump someone else from the score list. TABLE 1-8 AUDIT TOTALS The UP Switch is used to zero the audits. To advance to the nex screen, activate the Advance Test Button on the Coin Door. High Scores
1.8.21 COIN SLOT PROGRAMMING This screen allows the user to either select a standard coinage setting for the game or program his own. If a standard setting is desired, use the UP and DOWN Switch to adjust the coinage setting while it is lit in green. The values for the variable will change as this number is altered. When the right selection is set, use the Advance Test to return to the game. If a non-standard setting is desired, use Advance Sub Test Switct to move down to the variables so that they may be programmec individually. Once this switch is pressed, the setting number is se’ to zero to show that the location has supplied their own settings. As the lower variables are unchanged, the user may minimize his effor! by first selecting a setting close to the one he desires. Once in programming mode, the Advance Sub Test Switch is used to move among the variables. It will also take you back to the standard settings, if you press it by mistake. The UP and DOWN Switches are used to increment or decrement the values. Advance Test Switch will return to the game when pressed.
TH GUT HUHIpHe! tH HUW Many Wun UND ale auEU IMT cau soin through a particular slot. Coin units for credit show the number of units necessary before a bonus credit is issued. Minimum coin is an optional value which will keep the credits from accumulating until the specified minimum amount of coin units is reached. It is not used in any of the standard settings. 1.6.22 GMUS MEMUNT FAILURE If the message ‘Memory Failure - Service Required" appears on the screen, the CMOS RAM which stores all of the location pro-
CMOS RAM.
STANDARD COIN SETTINGS TABLE 1-9
Standard Setting Center coin slot multiplier Left coin slot multiplier Right coin slot multiplier Coin units for credit gramming has failed. All the values stored in the RAM are set back to factory defaults. This condition probably indicates a battery failure or a failure of U85 or U86. Refer to Section 2 on Maintenance or 2.8
Coin units for bonus Minimum coin units
COIN DOOR MECHANISMS CREDIT/MONEY STANDARD ¥/.25, 4/91 1/.50, 3/41, 6/2 1/.50 1DM, 5 DM 1/10M, 6/5DM 1 FRANC, 5 FRANC V2F, 3/5F ONLY 8/8/2/8)8/8 25 CENTS, 1 GUILDER 1/25, 4/1G 5 FRANCS, 10 FRANCS 4VSF, 2/10F 1/10F
| 1 FRANC, 2 FRANC | QF, S/F | 09 | 00 | |
| 1 UNIT, 5 UNITS | 112, 45 | 10 | 01 | |
| TWIN COIN | 1/1 COIN | 01 | 01 | 04] | O1 | Ot | 00 |
1/2 COINS 00
CUSTOM COIN SETTINGS TABLE 1-10
3s 3/3
| ZF) | Els | &| | Bl | s | |
| gl|s| | 2 | 5/5] | |||
| g/ | 3) | 2 | 5) | 5| | 38 |
| zl | s|s | =/=/ | 6 | ||
| sg | sis | 5 | 5 | 2 |
COIN DOOR MECHANISMS CREDIT/ MONEY
| STANDARD | 17.25, 51 | oo | orf | of} | or] | ov | o4 | 00 | ||
| 27.50, 51 | oo | {or} | os} | or] | or] | 04 | 02 | |
| 27.50, 41 | oo | or} | of | or] | or| | 00 | 02 | ||
| 1750, 391, 41.25 | 00 | 03} | 12} | 03] | o+| | 15 | 00 | ||
| 17.50, 391, 792 | oo] | 2| | @| | 2] | 4] | 8] | 4 | |
| 25 CENTS, 1 GUILDER | 1725, 5G | 00 | 00 | 04 | 00 | |||
| 100 LIRE, 200 IRE | 1/200 LIRE | 00 | 00 | ||||
| TWIN COIN | 13 COIN, 25 | 00 | 00 | ||||
| T UNIT, 5 UNITS | 11, 55 | 00 | 00 | ||||
| 13, 25 | 00 | 00 |
NOTES
Maintenance
ALL GAMES REQUIRE A CERTAIN AMOUNT OF MAINTENANCE TO KEEP THEM IN GOOD WORKING ORDER. A PERIODIC CHECK OF THE MECHANICAL CONTROLS WOULD BE BENEFICAL TO THE SUCCESS OF YOUR GAME.
2.1 CLEANING The exterior of the game, all metal parts and all plastic parts can be Cleaned with a non-abrasive cleanser. Caution should be used when cleaning the glass, a dry cloth can cause scratches and result in a foggy appearance.
2.2 COIN DOOR The Coin Door used in the “‘KRAM''™ game needs little or no maintenance. See Figure 2-1. If desired a special coin mechanism Cleanser, that leaves no residue, can be obtained from your distributor. Refer to the manufacturers documentation if additional information is needed.
FIGURE 2-1 COIN DOOR
2.3 FUSE REPLACEMENT This game contains 8 fuses. Seven of these fuses can be found on the Power Supply Assembly, five (5) are on the PCB and two (2) are on the Power Supply Bracket. One (1) is located at the bracket where the AC line cord comes into the cabinet. See Figure 2-2 for locations of these fuses.
FIGURE 2-2 FUSE REPLACEMENT WW yuu Neva ww remove tne video Monitor, follow the instruction listed below:
© Disconnect power from the line voltage © Disconnect the Monitor cable connector. Remove the wire cable clamp. Take out the two side bolts, one on each side of the cabinet. Remove the four mounting bolts and disconnect the green ground wire. . © Slide the Monitor out by pulling the Monitor toward you
FIGURE 2-3 MONITOR REMOVAL
G9 UUYER uLAge nemuNne To remove the Cover Glass follow the instructions listed below:
- Remove the Control Panel.
- Loosen three (3) screws on the Cover Glass, front bracket.
- Open the Service Door and remove the (Rear) Cover Glass Bracket.
- Slide the glass out through the Service Door.
2.7 POWER SUPPLY The Power Supply produces all the necessary game voltage requirements. Refer to Figure 2-6 while reading the following circuit description.
FIGURE 2-4 COVER GLASS REMOVAL
2.6 PRINTED CIRCUIT BOARD REPLACEMENT You may wish to remove the ‘‘KRAM"'™ printed circuit board, Video Processor (08-00001-002), Data/ Sound Board (08-00002-002). or ROM 1/0 Board (08-00030-001) for servicing. Refer to Figure 2-5. The ‘“‘KRAM'’™ Printed Circuit Boards (PCB) are located on the inside of the rear service door for easy access.
- Open the Rear Service Door, the power will automatically be removed by the Interlock Switch located on the inside of the door frame.
- Disconnect the connectors from the board or boards you wish to remove.
- Disconnect the ribbon cable, connecting the boards by spreading eject latches on the connector.
- Remove the screws for the board you wish to remove. FIGURE 2-6 POWER SUPPLY
2.7.1 AC INPUT The AC Input Voltage is applied to the main Power Supply via the AC Line Cords, Line Filters, Line Fuse, Power Switch and Interlock Switch. Different Line Cords are used for 120V and for 240V. The Line Fuse is located on the Line Cord Assembly near the Strain Relief. A Voltage Programming Block is located on the primary side of the Transformer to compensate for high/low voltage conditions. The following line voltages may be made by inserting the appropriate Programming Plug.
Line Fuse
3 AMP 3 AMP 1.5 AMP 1.5 AMP 1.5 AMP Line Voltage 100 VAC + 10% 120 VAC +10% 200 VAC + 10% 220 VAC + 10% 240 VAC + 10% 50/60HZ 50/60Hz 50/60Hz 50/60Hz 50/60Hz TARLF 9.1 LINE VAI TAGE
vauniure For continuous protection against fire hazard, replace only with a fuse of the same type having the same electrical rating. There are five secondary sources. Three go to the Regulator PCB providing +5VDC, +12VDC, —12VDC and —5VDC. The other two are fused 6.3VAC used for the incandescent lighting and fused 120VAC used for the monitor, and in certain models for a flourescent lamp and fan. These secondary fuses are located on the bracket adjacent to the Power Transformer.
Secondary Fuse 120VAC 2.0AMP SLO-BLO, 6.3VAC 2.5AMP TABLE 2-2 SECONDARY FUSES Circuit
2.7.2 ~5VDC AND —12VDC REGULATORS The AC Input for the negative voltages comes into the Regulator PCB on J1-5 and J1-6 from the Transformer. Fuse F3 protects against short circuits. The AC Voltage is then full wave rectified by BR3 and filtered by C16. The raw DC is then applied to Reg 1,a three terminal - 12V Regulator. The output of this Regulator is the
- 12VDC output for the system and is also the input voltage for Reg 2, a —5V Regulator. The output of this Regulator is the — 5VDC for the system. Capacitors C17, C18, C19 are to improve the transient response and stability of the minus voltage regulator. Diodes D8 and D9 provide protection against C18 and C19 being shorted through the Regulator. Resistors R34 and R35 provide current limiting for LED'S 3 and 4 which will light when there is voltage present at the regulation outputs. 2.7.3. +5VDC REGULATOR The AC Input for the +5VDC Regulator circuit comes in on J1-4 and J1-2, via F1 into BR1 full wave rectifies the AC Input. This raw DC is applied to the collectors of (2) series pass transistors, mounted on the Heat Sink Assembly. The regulation is done by U3, which is a voltage regulator whose output controls the gain of 5, which in turn controls the gain of the series pass transistors. The emitter of te series pass transistor return to the Regulators PCB and through R11 and R12, which serve to force current sharing between the series pass devices. The voltage at the output of R11 and R12 are the +5VDC for the system. R11 and R12 are voltage set and current foldback adjustments respectively. These are factory adjusted to 5V .25V at AMPS. Q8, D3 and R20 comprises a SCR-Type Crowbar Circuit which will trigger when the OC output voltages rise above 5.8V. Once the SCR fires, the Power Supply has to be turned off to reset the device. R19 is a current limiter for the voltage indicator LED 1. R16 is used to set up the output voltage of the Regulator. C8, D2, R13 and 04 delay the start up of the 5V Regulator to allow the —5VDC Regulator to stabilize first. 2.7.4 +12VDC REGULATOR This circuit is essentially the same as the 5V REgulator described above. The AC current comes in on J1-3 and J1-4, via fuse F2 into BR2. The ACisrectified by BR2 and filtered by C9. The raw DC is fed into a single series pass transistor on the Heat Sink Assembly and also powers the +12V and +5V Regulator. R28 and R25 are voltage set and current foldback and factory adjusted to 12 Volts +Volts +.25V at 4AMPS. 07, Q9 and R31 are SCR Crowbar Circuits which trigger at 13VOC output which causes supply to go into Current foldback. There is an RC delay as in the 5V circuit to delay the + 12V rise time. The reset circuit will output a 2sec active low MRST pulse at J3-14 J4-14 when the power is first turned ON and whenever power fails for more than 35ms. The reset circuitry is comprised of a Dual Timer (556) and a fullwave type optical coupler across an AC secondary. The output of U1 is the input to one half of the 556 which is configured as a missing pulse detector. C1 and R3 determine the time before the output goes active. This is set for about 35ms. When two or more cycles are missing, the output of the first timer triggers the second timer which drives the MRST low for about 2 seconds. The timer constant for the second timer is set for R4 and C6. Power on reset is generated by C4, and R39 and D12 on the trigger input of the second timer. 03 inverts the signal out of the 556 so it is active low. R7 insures MRST is low while the power is rising.
2.7.6 POWER SUPPLY ADJUSTMENTS VOLTAGE Adjust voltages on +5V and +12V for +5.00V to +5.05V and —12.00V to +12.05V. CURRENT LIMITER Adjust control (5I and 121) counterclockwise until voltage just changes, then turn control clockwise until voltage goes back to original value with pointer, mark position of arrow on ‘potentiometer then turn control until beginning of 1st notch is aligned with the pointer. On the controls with the Blue Disk turn approximately 30°.
FIGURE 2-7 CURRENT LIMIT ADJUSTMENT
2.8 CMOS RAM If when powering the game up, it will not coin up because the battery is low. The following Procedure should be followed. Open the Back Door of the game, pull W1 out on the Video Board (Blue Jumper). Wait 2 minutes, power back on and insert W1 back in. Open the Coin Door and pull out bottom Interlock Switch. If the Language Select Frame does not come on the CRT, power down remove W1 again. Short pins 18 and 9 on U85, power back on and insert W1 back in. Leave the game on for 12 hours. If this Procedure does not work when you turn the game back on the battery may need to be replaced.
2.9 TEST POINTS The following is a list of Test Points to be used when troubleshooting.
DATA/SOUND BOARD (Master Clock) (Master Clock) Last Instruction Complete (Address Line) (Address Line)
(Sound Processor Data Enable) (Data Processor Data Enable)
(Clock Video Processor) (Clock Video Processor) (External Clock) Last Instruction Complete (Video Data Enable)
TABLE 2-4 VIDEO BOARD TEST POINTS
lf you ground any Data Enable Test Point (DTP7, DTP8, VTP7) the related processor will receive NO-OP and the address line will act like a 16 Bit Counter.
NOTES
Operation
THIS SECTION PROVIDES A TECHNICAL DESCRIPTION OF THE ‘“‘KRAM’’™ GAME. THE GAME ELECTRONICALLY CONSISTS OF PRINTED CIRCUIT BOARDS, TV MONITOR, POWER SUPPLY, AND SPEAKERS WHICH ARE DESCRIBED IN DETAIL IN THE FOLLOWING TEXT.
- Intunt ur urcnaniun
3.1 GENERAL The TAITO AMERICA CORPORATION'S arcade video system game is an advanced multiprocessor based circuit utilizing the Motorola 6809E microprocessor. The system is organized in three logical blocks: A. The Data Processor, which supervises the operation of the entire system. B. The Video Processor, which performs all screen based functions, such as playfield image motion, line drawing, etc. C. The Sound Processor, which generates sounds under the direct control of the Data Processor. In order to facilitate easy inter-system communications, the Data and the Video Microprocessor run synchronously using clock and timing signals developed on the Video Board. For this reason, discussion will begin by examining the Video Board.
3.3 VIDEO BOARD 3.2.1 SYSTEM CLOCK The fundamental system clock is developed by the 20MHZ crystal, inverters U24 and U39, and components. The 20MHZ signal is divided by the high speed flip flop U38 to obtain a 10MHZ main clock with a precise 50 percent duty cycle. This 10MHZ signal generates all other fundamental timing signals for the video system including the Data Processor. 1C23 divides the 10MHZ signal to obtain SMHZ, 2.5MHZ and CCLK, and their respective inversions. IC's U9, U37, and U38 combine these signals, presenting them to U25, which synchronizes the output signal to the system 10MHZ clock. This circuit produces waveforms whose active edges are synchronized to 15ns worse case, 2ns average. The characteristics of the clock circuit may be noted by reference to the Timing Diagram, Figure 3-1.
| i= wwe J} = rt yt LT 5 swe f \ 7 1 2siea i ij a nsw i eaux I ° i, —m i
ARERR ETT BI
ocK TIMING.
FIGURE 3-1 CLOCK TIMING 3.2.2 SCREEN RAM The Video Processor controls a Screen RAM of 256 X 256 pixels with 8 bits per pixel. In order to access of this information, the screen is divided into two pages, top and bottom, chosen under software control. These pages are both addressed at 0000 - 7FFF with address 0 corresponding to the lower left corner of the screen (horizontal scan). All CRT accesses to this RAM are transparent to the processor and the RAM may be read or written any time. The timing of the Screen RAM and the eventual scan is controlled by a 6845/6545/46505 CRT Controller Chip. It's address outputs are gated by U19, U20, U50, or US1 for inversion when used in a Cocktail table mode. The scan addresses are multiplexed with the address present on the microprocessor address bus by U35, U52, U53 and U54 for standard RAS-CAS accessing. The desired bank of Memory is addressed by U87, a one of four decoder. Data written into the Screem RAM comes directly from the system data bus, buffered by 33 Ohm resistors. |f a processor read is taking place, the data is placed on the data bus by U77, U78, U79 and U80. First byte, screen reads are latched by 374's U91, U92, U93 and U94. A second byte screen read is then performed and this data, together with the data from the first screen read latched by the 374's is loaded into the eight (8) 74LS299 shift registers. These registers may be shifted in either direction for cocktail table implementation. The byte stream then proceeds to the Color RAM.
VIDEO BOARD MEMORY MAP Dual Port RAM CMOS Batter Backup Memory LED Output and Color RAM Page Select Data FIRQ Activation Address Video FIRQ Deactivation Address Color RAM Address Latch Hi-Byte Address Latch Lo-Byte Address Latch Indexed Screen Location Scan Line Readback Location CRT Controller Base Address TABLE 3-1 VIDEO BOARD MEMORY MAP (S$ = HEXADECIMAL) 3.2.3 DUAL PORT RAM This RAM may be accessed in its entirety by either processor. This is arbitrated as follows:
- The Data Processor runs in quadraturne with (one quarter clock cycle ahead of) the Video Processor. In other words, E is inverted for use as DQ, and Q becomes DE. Refer to Timing Diagram, Figure 3-2.
- The Data Processor, by nature of this timing, accesses the Dual Port RAM ‘% cycle before the Video Processor. At this point the Video Processor is guaranteed to not be accessing the RAM. The Data Processor access is flagged by U36, which causes a cycle to be stolen from the Video Processor’s main clock, VO and VE.
- The Video Processor is unable to access the Dual Port RAM unless the Data Processor is not accessing it as it will not be receiving clocks during that time. The cycle steal is accomplished by the generation of signal DPMUX by U36. This signal directly steals the cycle, and also folds over multiplexers U5, U6 and U21, switching the address lines, R/W and gating signals. U1 and U2 gate the data to or from the desired Processor. U22 insures that no spurious writes are generated during foldover.
ona Lr 2 ous ty am oe v f
FIGURE 3-2 PORT RAM TIMING -
3.2.4 CMOS RAM The CMOS RAM is implemented for use as both a battery back-up storage area and a work area for the Video Processor. The gating U100, U101, U102 and U103 insure that writes to the block of RAM form $8700 - 87FF cannot be performed unless the Coin Door is open (J19-2 grounded). The 3.6V NiCAD battery is trickle charged by Q8, R64 and R65 when the system is powered. When turned off, supply current for U85, U86 and U100 is provided by this battery. U100 is included to solidly gate the MRST signal and prevent invalid operations during power Up and Down. LED and Color RAM Page Latch, U72, is addressed at address $8800. The upper six bits drive LED’S on the circuit board for diagnostics which cannot be done through the screen. The lower 2 bits select the Color RAM page and will be discussed later.
3.2.5 BI DIRECTIONAL FIRQ CAPABILITY To provide for immediate inter-system communication on demand a Bi-Directional FIRO capability has been provided. Any access of address $8C00 by the Video Processor will generate a FIRQ to the Data Processor will remove a FIRQ generated by the Data Processor to the Video Processor. This is accomplished by U7, U8 and U9.
3.2.6 COLOR RAM The Color RAM is used as a translation matrix so that a number of different pixel values may access a given color, or to change the color of a given area of the screen without rewriting the Screen RAM. The serial bit stream, eight bits wide comes from the shift registers of the Screen RAM to be presented to multiplexers U55, U73 and U74. These select between the Video Processor bus and the serial bit stream. As processor access times are considerbly greater than the basic bit time (200ns), it is necessary to access through U75, and serial output is latched by U76. This Data Stream is converted to a color pallet of 64 colors and four intensities. When the serial bit is selected for access, the two high order bits are provided by the LED output latch. This allows the Programmer to select between four pages of RAM rapidly.
3.2.7 ADDRESS LATCH CIRCUITRY Two methods of Screen Memory Address are provided:
- A 16 bit address may be written into latch U70 and U71 addressed at $9402 and $9403. The addressed location may be accessed by reference to location $9400. may be directly addressed by reference to locations $0000 - $7FF. U36, U70 and U71 latch the address. U36 is used in conjunction with U70 as U70 and U71 are tri-stated when inactive, The screen address deposited on the LA Bus by U84 and U98 for Processor Bus accesses, and by U70 and U71 for latched address. Decoding is performed by U87 and U88.
3.2.8 SCAN LINE READBACK When read, this location is the number of the scan line currently being drawn by the beam. U34 latches the last row address drawn and U101 prevents erratic updating at the end of a horizontal line. There are 256 valid scan lines 00 - FF.
3.2.9 CRT CONTROLLER The 6845/6545/46505 is a software programmable sync and scan generator. It has two ports based at $9C00 and $9C01. It is recommended that the reader consult Motorola, Hitachi, Rockwell, or Synertek supplied documentation. Register initialization are as follows:
Description Horizontal total-1 Horizontal displayed Horizontal sync position Sync pulse width Vertical total-1 Vertical hold adjust Vertical displayed Vertical sync position Scan lines per row-1 TABLE 3-2 REGISTER INITIALIZATION Initialization (decimal)
3.3 DATA/SOUND BOARD The Data Processor runs synchronously to the Video Processor, as was described in this Section (Dual Port Memory). All basic timing signals originate on the Video Processor Board and are bused onto the Data Processor Baord. This Sound Processor and Amplifier circuitry also resides on this board.
3.3.1 MEMORY MAP The following devices are available for access to the Data Processor.
Dual Port Memory Local Memory ACIA Base Address Video FIRQ Activation Address Data FIRQ Deactivation Address Sound PIA Game PIA 1 Game PIA 2 Game PIA 3 TABLE 3-3 DATA/SOUND MEMORY MAP (S = HEXADECIMAL)
3.3.2 DUAL PORT MEMORY See discussion of Dual Port Memory under Video Processor Heading (Section 3.2).
3.3.3 LOCAL MEMORY This is a 1K block of memory, U15 and U16, provided for scratch and work area for the Data Processor.
3.3.4 ACIA A Motorola 6850 ACIA has been provided for diagnostic and other communications. Timing is generated by crystal oscillator Y1-U23 and prescaled by U27 and U26. SW1 may be configured to allow one of eight baud rates (2 speeds may be software selected in the ACIA). Correct RS-232 levels are provided by U25 and U21.
3.3.5 BI-DIRECTIONAL FIRQ CAPABILITY Any access of $8C00 will generate a FIRQ to the Video Processor. Any access of $8C01 will remove FIRQ generated by the Video Processor to the Data Processor. This is accomplished by U7, U8 and U9 which resides on the Video Board.
3.3.6 SOUND PIA Both Ports of PIA U20 have been dedicated to the control of the Sound Processor. Port A is used to select a sound number, which is initiated by strobbing the U20 (CA2) - U8 (CA1) interrupt. Port B is used to control the amplitude of the generated sound to the Stereo Amplifiers. The output side B go to U24 and U28, which vary the ratio of the voltage divider across the noninverting inputs of U29 and U30. This allows balance control of the sound to coincide with real time events occuring on the screen.
3.3.7 GAME PIA’S Three 6820's are provided for interfacing with Play Controls and Coin Door Switches. These are located on the Game Board and are accessed through a Jumber Cable J16 and J15 respectively.
3.3.8 SOUND PROCESSOR A motorola 6802 resides on the Data Board for generation. This Processor runs at 3,68MHz and accesses only two devices. PIA’S U7 and U8. U8 as mentioned previously, interface to the Data Processor. It is also the digital to analog output of the Sound Processor. Data from Port B is presented to U13. The current based output is Converted to a voltage output by Q1, and controlled in amplitude by a potentiometer placed across J8. Speech circuitry is mixed with sound by RQ, and the sum is sent to the Amplifiers. U7 controls the speech synthesis chip U19. The speech signal is shaped and filtered by the multipole bandpass filter U18. 3.4 ROM/I/0/BOARD This board contains the Program ROM for both the Data, Video and Sound Processors, along with the PIA’S needed to interface control coils, lamps, etc.
3.4.1 GAME PIA’S Three Game PIA’S are located on the board $9400, $9900, $9C00. These devices, U11, U20 and U30 respectively, interface through noise control circuits A or B filbers for those lines dedicated to inputs. Eleven (11) High Current Drivers have been provided utilizing circuit C. Each of these is capable of switching a 1.5 AMP/ 24Volt load to ground.
3.4.2 ROM'S Eight ROM locations are provided for the Data Processor, U12 - U19. These are selected by U21. Eight ROM’S U3 --U10 selected by U2 are dedicated to the Video Processor. Sounds are supported by ROM’S U25, U26, U27, with select U28.
ROM Bank U3 - U10 may consist of either 2716 or 2732 type
EPROMS as determined by a jumper plug inserted in U1. It is assumed that all such EPROMS in the bank are of the same type. Likewise, ROM Bank U12 - U19 is determined by jumper plug at U22 ROM Bank jumpering for 2716's is as follows: Pin 1-14, 2-13, 3-12, 4-11 and 5-10. The highest Address EPROM is U10, U19 or U27 in each bank with addresses of adjacent sockets progressing downward in $800 byte blocks. Jumpering for 2732's is as follows: Pin 2-14, 3-13, 4-12, 5-11 and 6-10. The highest Address EPROMS is U10, U19 or U27 in each bank with addresses or adjacent sockets progressing downward in $1000 byte blocks.
Illustration
&
Parts Lists
NUNNWweVULN EA FIGURE 1
TAITO PARTNO. | DESCRIPTION .27-00006-001 | Lamp #47 26800009-001} Bayonet Base Socket 61000112-001 | Marquee Lighting
TAITO PART NO. O-WAT yUTOTIUN
FIGURE 2
DESCRIPTION 63B00031-001 Ball & Shaft 63A00033-001 Mask 63C00027-001 Mounting Plate 62C00002-001 Shock Mount Pad 63C00028-001 ‘Switch Plate 63A00030-001 Actuator 61A00078-001 “L” Bracket 63A00026-001 Switch S; 29800018-001 Leaf Switch 63A00029-001 Spacer
CONTROL PANEL FIGURE 3
DESCRIPTION
Push Button (Yellow)
Stamped Nut 94-11
Leaf Switch
CONTROL PANEL
FIGURE 3
DOOR ASSEMBLY FIGURE 4
TAITO PARTNO. | DESCRIPTION Car 00037- “7 Lock Kit
NOTES
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
CABINET ASSEMBLY UPRIGHT FRUNI Virw FIGURE 5
ITEM DESCRIPTION 07M00055-002| Incandescent Panel 63B00006-001 | 63B00006-003 ‘'U"’ Channel 47000012-005 | Marquee 61000115-001 | Marquee Retaining Bracket 61D00012-001 | Lower Cover Glass Bracket 07M00052-004 | Control Panel Assembly 07-00115-001 | Coin Door w@lriola]sfolrmj— 61B00113-001 | Switch Bracket g | 07M00057-001 | Service Switch Assembly 10 | 29-00022-001 | Slide, Center Return Switch 11_| 29800015-001 | _ Interlock Switch 12 | 61B00114-001 | Interlock Switch Bracket 13 | 59-00008-001 | Latching Clamp 14 _| 63B00002-004 | _‘T’' Molding 15 | 29A00023-001 | Power ON/OFF Switch 16 | 41D00015-001 | Finish Cabinet 17 |07M00116-001 | Volume Control Assembly 48 | 61000212-001 | Volume Control Bracket 29-00026-001 | Switch Interlock Non Cheat
CABINET ASSEMBLY UPRIGHT FRONT VIEW
FIGURE 5
TAITO PART NO. VABING! AOOCMOLE UrMUN ncAn vice FIGURE 6
DESCRIPTION 21€00003-001 Speaker 6” round 61B00009-001 Speaker Grill 41000015-001 Finished Cabinet Upper Cover Glass Bracket 63S00053-001 Monitor Shroud 61D00208-001 Monitor Mounting Bracket 27-00006-001 #47 Bulb, Lighted Instr. 26-00008-001 Socket, Snap-on Bayonet 47000016-002 Cover Glass 44C00001-001 Wheels 63C00005-004 “L" Molding 07M00042-001 A/C Line Cord Assembly 63C00005-002 "LE" Molding 61B00030-002 Interlock Bracket 59B00045-001 Switch Barrier 29800015-001 Interlock Switch 07M00039-001 Power Supply 61000054-001 Cash Box Lid '31-00004-001 19” (Horz.) Color Monitor 63-00019-001 Cash Tray Separator 61-00039-001 Cash Tray Handle 61C00060-001 Cash Box 63-00010-001 Cash Tray (Only) 07M00054-001 Cash Tray Assembly 42000013-001 Monitor Support Cleat 08M00002-002 Data/Sound P.C.B. 61B00142-001 Lock Rod Assembly 08M00030-001 ROM/10 P.C.B. 04M00037-002 Lock Kit 08M00001-002 Video Processor P.C.B. 61000079-001
CABINET ASSEMBLY UPRIGHT REAR VIEW
FIGURE 6
vw i FIGURE 7
er Leal 100-10000-80
TAITO PART NO. DESCRIPTION FIGURE 7
TAITO PART NO. DESCRIPTION
41-00001-102 Resistor 1.0K 5% ‘%«W 5% 12-10001-102 Capacitor, .0O1uf
11-00001-512 Resistor 5.1K %4W 5% 12-30001-106 Campacitor, Tantalum 10uf
11-00001-183. Resistor 18K MW 5% 12-20003-509 Capacitor, Electrolytic 50,000ut 11-00001-224 Resistor 220K YW 5% 12-30001-105 Capacitor, Tantalum 1.uf 35V 11-00001-472 Resistor 4.7K 4W 5% 12-20003-209 Capacitor, Electrolytic 20,000ut 11-00001-222 Resistor 2.2K %&4W 5% 12-10001-332 Capacitor, Ceramic .0033ut 11-10001-101 Resistor 100 4W 5% 12-30001-476 Capacitor, Tantalum 47ut
11-00001-102 Resistor 10K %&W 5% 12-30001-105 Capacitor, Tantalum 1.uf 35V
11-00001-472 Resistor 4.7K ”4W 5% 12-10004-103 Capacitor, Ceramic .Otuf
11-10001-101 Resistor 100 2W 5% 12-10001-102 Capacitor, .0O1uf
11-30001-015 Resistor .15 4W 5% 12-30001-476 Capacitor, Tantalum 47uf
11-30001-015 Resistor .15 4W 5% 12-20002-108 Capacitor, Electrolytic 1,000ut 11-00001-472 Resistor 4.7K YW 5% 12-30001-225 Capacitor, Tantalum 2.2uf 25V
11-00001-222 Resistor 2.2K 4W 5% 12-30001-225 Capacitor, Tantalum 2.2uf 25V
11-00001-222 Resistor 2.2K YW 5% 12-30001-105 Capacitor, Tantalum 1.uf 35V
11-60001-252 Pot 2.5K ‘4W 20% 24-00003-010 10A Fuse
11-00001-222 Resistor 2.2K ‘aW 5% 24-00003-010 10A Fuse
11-60001-102 Pot 1.0K YW 20% 24-00003-003 Fuse, 2A
11-00001-511 Resistor 510 ‘aW 5%. 24-00003-004 Fuse, 4A was labeled 5A
11-10001-470 Resistor 47 zW 5% 24-00003-004 Fuse, 4A was labeled 5A
11-00001-162 Resistor 1.6K %4W 5% 13-00100-025 Diode Bridge 25A, 100V
11-00001-103 Resistor 10K YW 5% 13-00100-012 Diode Bridge 12A, 100V
11-00001-472 Resistor 4.7K ‘MW 34 13-00100-002 Diode Bridge 2A, 100V
11-00001-222 Resistor 2.2K ‘aW 5% 13-14002-001 Diode IN4002
11-60001-102 Pot 1.0K &@W 5% 13-14002-001 Diode IN4002
11-00001-472 Resistor 407K YW 5% 13-10752-001 Diode, Zener IN752
11-00001-222 Resistor 2.2K %4W 5% 13-14002-001 Diode IN4002
11-60001-252 Pot 2.5K YW 20% 13-14002-001 Diode 1N4002
R29 | 11-00001-472 Resistor 4.7K YW 5% 13-14002-001 Diode IN4002
R30 | 11-00001-122 Resistor 1.2K “4W 5% 13-10964-001 Diode, Zener IN964
R31 | 11-10001-470 Resistor 47 %W 5% 13-14002-001 Diode IN4002
R32 | 11-30001-015 Resistor .15 4W 5% 13-14002-001 Diode IN4002
R33 | 11-00001-222 Resistor 2.2K aW 5% 13-14002-001 Diode IN4002 R34 | 11-00001-122 Resistor 1.2K YW 5% 13-14002-001 Diode IN4002
R35 | 11-00001-511 Resistor 510 4W 5% 13-14002-001 Diode IN4002 R36 | 11-00001-222 Resistor 2.2K YW 5% 13-14002-001 Diode IN6276 or 1.5KE 16
R37 _| 11-00001-104 Resistor 100K 13-14002-001 Diode IN6218 or 1.5KE 27 R38 | 11-00001-103 Resistor 10K YW 5% 13-14002-001 Diode IN4002
R3Q | 11-00001-224 Resistor 220L M4W 5% 13-14002-004 Diode IN4002
R40*| 11-00001-225 Resistor 20HM _%4W 13-00001-001 LED (Red)
12-30001-225 Capacitor, Tantalum 2.2uf 25V 13-00001-001 LED (Red)
12-10004-103 Capacitor, Ceramic O1uf 13-00001-004 LED (Red)
12-10004-103 Capacitor, Ceramic .O1ut 13-00001-001 LED (Red)
42-30001-105 Capacitor, Tantalum 1 .uf 35V 15-62500-001 Opto Coupler H11AA2 15-50556-001 Timer (Dual) 556 15-50723-001 Voltage Regulator 723 15-50723-001 Voltage Regulator 723
POWER SUPPLY FIGURE 7
DESCRIPTION 15-57912-001 | Voltage Regulator 7912 15-57905-001 | Voltage Regulator 79L05 [at _[14-22905-001 | Transistor 2N2905 [2 | 14-22905-001 | Transistor 2N2905
[a5 | 14-23055-001 | Transistor 2N3055 Q6 | 14-22905-001 | Transistor 2N2905 [1e-2640r-00r [oR Newari [14-26401-001 [ScR 2Ne4o1
[2e-io00r-oot [Fuse Gps 30-00003-001 | Heat Sink Single To-3 g
VIUEU rnuUucIoUN FIGURE 8
TAITO TAITO ‘SYM | PART NO. DESCRIPTION SYM | PART NO. DESCRIPTION C1 | 12-10002-104 | Capacitor Ceramic, .tuf,50V, +80/—20% C55 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C2 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/-20% C56 | 12-10002-104 | Capacitor Ceramic, .1uf,S0V. +80/—20% C3 | 12-10002-104 | Capacitor Ceramic, .tuf,50V, +80/-—20% C57 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/-20% C4 | 12-10002-104 | Capacitor Ceramic, .tuf,50V, +80/-20% C58 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C5 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/-20% 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—36 C6 | 12-10002-104 | Capacitor Ceramic, .tuf,50V, +80/—20% 12-10002-104 | Capacitor Ceramic, .1ut,50V, +80/-20% C7 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/-20% 12-30001-106 | Capacitor Tant, 10uf, 16V C8 | 12-10002-104 | Capacitor Ceramic, .tuf,50V, +80/-20% 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C9 | 12-30001-106 | Capacitor Tant, 10uf, 16V 12-30001-106 | Capacitor Tant, 10uf,16V C10 | 12-10002-104 | Capacitor Ceramic, .tuf,50V, +80/~20% 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C11 | 12-10002-104 | Capacitor Ceramic, .1uf,S0V, +80/—20% 12-10001-471. | Capacitor Ceramic, 470uf,50V,10% X7R €12_| ¥2-10002-104 | Capacitor Ceramic, .tuf,S0V, +80/—20% Axial Lead €13 | 12-10002-104 | Capacitor Ceramic, .tuf,50V, +80/—20% 42-10002-104 | Capacitor Ceramic, 1uf,S0V, +80/—20% 14 | 12-10003-101 | Capacitor Ceramic, 100pf, 10% NPO Axial Lea 12-10002-104 | Capacitor Ceramic, -Tut,S0V, +80/—20% 15 | 12-10002-104 | Capacitor Ceramic, tuf,50V, +80/—20% 12-10002-104 | Capacitor Ceramic, -tut,50V, +80/-20% Ci6 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% 12-10002-104 | Capacitor Ceramic, Tuf,S0V, + 80/—20% Ci7 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/— 20% C70 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/-20%
| tie | ae Capacitor Ceramic, .1uf,50V, +80/—20% | C71 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% |
19 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% €72 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/-20% (20 | 12-10002-104 | Capacitor Ceramic, .tuf,50V, +80/-20% C73 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/-20% C21 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C74 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/-20% (22 | 12-30001-106 | Capacitor Tant, 10uf, 16V C75 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% 23 | 12-10002-104 | Capacitor Ceramic, .tuf,50V, +80/—20% C76 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20%
| 26 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/-20% | | C77_| | 12-30001-106 | Capacitor Tant, 10uf, 76V |
Ca7 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C78 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/-20% 28 | 12-10002-104 | Capacitor Ceramic, -1uf,50V, +80/-20% C79 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/~20%
| G29 | 12-10002-104 | Capacitor Ceramic, 1uf,50V, +80/—20% | C80_| | 12-30001-106 | Capacitor Tant, 10uf, 16V |
30 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C81 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% 31 | 12-10003-101 | Capacitor Disk 100pf, 10% NPO C82 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/-20%
| €32_| | 12-10002-104 | Capacitor Ceramic, 1uf,50V, +80/—20% | C83 _| 12-10002-104 | Capacitor Ceramic. 1uf,50V, +80/—36 |
33 | 12-10002-104 | Capacitor Ceramic, -1uf,50V, +80/-20% C84 | 12-10002-104 | Capacitor Ceramic, .1uf.S0V, +80/—20% C34 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/-20% C85 | 12-10002-104 | Capacitor Ceramic, .1uf,50V. +80/-20% 35 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/— 20% 86 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/— 20% 36 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C87 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% 637 | 12-10002-104 | Capacitor Ceramic, .tuf,50V, +80/-20% C88 | 12-20001-107 Gapactor, Electrolytic 100uf, 25,
| 38 | 42-10002-104 | Capacitor Ceramic, .1uf,S0V, +80/—20% | a9} | 12-20001-107 | Capacitor Electrolytic, 100uf,25V. |
C39 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/~20% +100/—20% C40 | 12-10002-104 | Capacitor Ceramic, 1uf,50V, +80/-20% C90 | 12-20001-107 | Capacitor Electrolytic, 100uf.25V, 41 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/-20% + 100/-20% 42 | 12-10002-104 | Capacitor Tant, 10uf,16V C91 | 12-10002-104 | Capacitor Ceramic, .1uf.50V, +80/-20% C43 | 12-10002-104 | Capacitor Ceramic, .1ut,50V, +80/—20% c92 | 12-10002-104 Capacitor Ceramic, .1uf,50V, +80/-20% 44 | 12-30001-106 | Capacitor Tant, 10uf,16V C93 | 12-10002-104 | Capacitor Ceramic, .tuf,S0V, +80/-20% C45 | 12-30001-106 | Capacitor Tant, 10uf,16V 94 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/~20% 50 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/~20% C95 | 12-10002-104 | Capacitor Ceramic, .tuf,50V, +80/—20% 51 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/- 20% €96 | 12-10001-471 | Capacitor Ceramic, 470pf,50V,10% X7R 52 | 12-10002-104 | Capacitor Ceramic, 1uf,50V, +80/-20% eal eae (53 | 12-10002-104 | Capacitor Ceramic, .1u,50V, +80/— 20% GOP? | 12-10001-471 | Capacitor Ceramic, 470p1-S0V.10%, XZ 54 | 12-10002-104 | Capacitor Ceramic, uf,S0V, +80/—20% 98 | 12-10001-471 | Capacitor Ceramic. 470pf,50V, 10% X7R Axial Lead
FIGURE 8 TAITO PART NO. 11-00001-473 R38_| 11-00001-332| ‘R39 | 11-00001-331 R40 | 11-00001-331 R41 | 11-00001-331 R42 | 11-00001-331 R43 | 11-00001-331 R44 | 11-00001-331 R45 | 11-00001-151 R46 | 11-00001-820) R47 | 11-00001-471 R48 | 11-00001-181 R49 | 11-00001-271 DESCRIPTION Resistor 47K OHM, YW, 5% Resistor 3300 OHM, MW, 5% Resistor 330 OHM, %&W, 5% Resistor 330 OHM, MW, 5% Resistor 330 OHM, %&W, 5% Resistor 330 OHM, %W, 5% Resistor 330 OHM, %&W, 5% Resistor 330 OHM, 4W, 5% Resistor 150 OHM, %W, 5% Resistor 82 OHM, %W, 5% Resistor 470 OHM, MW, 5% Resistor 180 OHM, 4 W, 5% Resistor 270 OHM, %4W, 5% R50 | 11-00001-473] Resistor 47K OHM, %&W, 5% R51 | 11-00001-330| Resistor 33 0HM, YW, 5% R52 _| 11-00001-330} Resistor 33 OHM, &«W, 5% R53 | 11-00001-330] Resistor 33 OHM, “W, 5% R54 | 11-00001-330| Resistor 33 OHM, %W, 5% RSS | 11-00001-330] Resistor 33 OHM, %W, 5%
| R56_| | 11-00001-330] | Resistor 33 OHM, YW, 5% |
R57 | 11-00001-330] Resistor 33 OHM, %W, 5% R58 | 11-00001-330| Resistor 33 OHM, %&W, 5% R59 | 11-00001-473] Resistor 47K OHM, YW, 5%
| R60_| | 11-00001-332] | Resistor 3300 OHM, %W, 5% |
| R61_| | 11-00001-391] | Resistor 390 OHM, %W, 5% |
R62 | 11-00001-332| Resistor 3.3K, MW, 5% R63 | 11-00001-102} Resistor 1K, %“W, 5% R64 | 11-00001-121] Resistor 120 OHM, %W, 5% R65 | 11-00001-151] Resistor 150 0HM, %W, 5%
| R66_| | 11-00001-332] | Resistor 3.3K, %&W, 5% |
R67 _ | 11-00001-332| Resistor 3300 UHM, %&«W, 5% R68 _| 11-00001-332] Resistor 3.3K, MW, 5% R69 | 11-00001-332| Resistor 3.3K, %4W, 5% R70 | 11-00001-472] Resistor 4.7K. %W, +5% FB1_|17-00001-001 | Ferrite Bead FB2_|17-00001-001| Ferrite Bead FB3 | 17-00001-001 | Ferrite Bead FB4 | 17-00001-001| Ferrite Bead FBS | 17-00001-001 | Ferrite Bead R37
tuf,50V, +80/- 20% luf,50V, +80/ -20%| itor Ceramic. .1uf,50V, +80/-20% acitor Ceramic, .1uf,50V, +80/ —20%| 42-10002-104 citor Ceramic, .1uf,50V, +80-20% 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% 12-10002-104 Capacitor Ceramic, .1uf,50V, +80/—20% 12-10001-471 | Capacitor Ceramic, 50V, 10% 470PF 12-10002-104 | Capacitor, .1uf, 50V+80/-—20% 11-00001-330 | Resistor 33 OHM, %W, 5% 11-00001-152 | Resistor 1.5K, %4W, 5% 11-00001-271 | Resistor 270 OHM, %4W, 5% 11-00001-271 | Resistor 270 OHM, %4W, 5% 11-00001-271 | Resistor 270 OHM, YW. 5% 11-00001-332 | Resistor 3.3K, %«W, 5% 11-00001-221 | Resistor 220 OHM, YW, 5% 11-00001-222 | Resistor 2.2K, %sW, 5% 11-00001-330 | Resistor 33 OHM, 4W, 5%. R10 | 11-00001-330 | Resistor 33 OHM. %&«W, 5% R11 | 11-00001-330 | Resistor 33 OHM. ‘&«W, 5% R12 | 11-00001-330 | Resistor 33 OHM, %W, 5% R13 | 11-00001-820 | Resistor 82 OHM, "sW, 5% R14 | 11-00001-181 | Resistor 180 OHM. 4W, 5% R15 | 11-00001-271 Resistor 270 OHM, YaW, 5% R16 | 11-00001-151 | Resistor 150 OHM, %W, 5% R17 | 11-00001-151 | Resistor 150 OHM, %W, 5% R18 | 11-00001-271 | Resistor 270 OHM, YW, 5% R19 | 11-00001-181 | Resistor 180 OHM, %W, 5% R20 | 11-00001-820 | Resistor 82 OHM, 4W, 5% R21_| 11-00001-330 | Resistor 33 OHM, %W, 5% R22 _| 11-00001-330 | Resistor 33 OHM, %W, 5% R23 T11-00001-330 Resistor 33 OHM, %&W, 5% R24 | 11-00001 330 [Resistor 33 OHM, YW, 5% R25 _| 11-00001-330 | Resistor 33 OHM. YW, 5% R26_| 11-00001-330 | Resistor 33 OHM, %W. 5%
| R27_| | 11-00001-330 | Resistor 33 OHM, YW, 5% | £86 1 17-00001-001} | Ferrite Bead | |
| R28 | |11-00001-181 | [Resistor 180 OHM, YW, 5% | EB7_117-00001-001/ | Ferrite Bead |
R29 | 11-00001-471 | Resistor 470 OHM. ‘aw, 5% 17-00001-001 | Ferrite Bead
| 830_| | 11-00001-471 | [Resistor 470 OHM, ‘AW, 5% | 17:00001-001 | Ferrite Bead |
R31 | 11-00001-471 | Resistor 470 OHM, YW, 5% 17-00001-001 | Ferrite Bead
| 832_{ | 11-00001-471 | [Resistor 470 OHM, “AW. 5% | 47-00001-001| | Ferrite Bead |
833 | 11-00001-471 | Resistor 470 OHM. Yaw, 5% 14-23904-001 | Transistor NPN Silicon (2N3904) 14-23904-001 03 |14-23904-001 Q4__|14-23904-001 Transistor NPN Silicon (2N3904) Transistor NPN Silicon (2N3904) Transistor NPN Silicon (2N3904) R35_{ 11-00001-391 | Resistor 390 OHM, %W. 5% R36 111-00001-330 IResistor 23HM UW 5% R34_| 11-00001-681 | Resistor 680 OHM. 4W, 5% |
TAITO PART NO. DESCRIPTION 14-23904-001 | Transistor NPN Silicon (2N3904) FIGURE 8
DESCRIPTION TAITO SYM_|PART NO. U1t [15-10001-001 RAM 16K x 1 Dynamic (4116) 14-23904-001 |Transistor NPN Silicon (2N3904) [26-00001-016 Socket DIP 16 Pin for U11 =
14-23904-001 |Transistor NPN Silicon (2N3904) 12 [15-10001-001 RAM 16K x 1 Dynamic (4116)
[Led1 |13-00001-001 14-23905-001 | Transistor NPN Silicon (2N3905) 26-00001-016 Socket DIP 16 Pin for U12
|. RED, TL-1% . RED, TL-1% 15-10001-001 13-00001-001 -D. RED, TL-1% 26-00001-016 . RED, TL-1% 15-10001-001 }26-00001-016 RAM 16K x 1 Dynamic (4116) Socket DIP 16 Pin for U13 RAM 16K x 1 Dynamic (4116) Socket DIP 16 Pin for U14 13-00001-001 . RED, TL-1% U15 |15-10001-001 RAM 16K x 1 Dynamic (4116) 13-00001-001 . RED, TL-1% 26-00001-016 Socket DIP 16 Pin for U15 19-00003-001 | CRYSTAL, 20,000MHZ U16 }15-10001-001 BAI
T TT
Test Point
P3. 20-00001-001 | Battery, NICAD, 3.6V, 1/3 AA 26-00001-016 RAM 16K x 1 Dynamic (4116) Socket DIP 16 Pin for U16 Switch Momentary RAM 16K x 1 Dynamic (4116) Socket DIP 16 Pin for U17
59-00021-001 59-00021-001 {Test Point CRT CONTROLLER 68A45 Socket DIP 40 Pin for U18 15-20086-001 59-00021-001 |Test Point Quad 2 Input Exclusive or (74LS86) 15-20086-001
'59-00021-001 [RP1 |11-50001-102 '59-00021-001 | Test Point U21 '59-00021-001 {Test Point u22 Quad 2 Input Exclusive or (74LS86) 15-20157-001 | Multiplexer Quad 2-Input (74LS157) Quad 2 Input or (74LS157) Test Point 15-20161-001 Counter, 4 Bit Presetable (74LS161) 1K OHM Resistor Sip Pack 15-20004-001 15-70374-001 RP3 RP4 |11-50001-332 {3.3K Resistor Sip Pack 11-50001-473 |47K OHM Resistor Sip Pack 11-50001-332 |3.3K Resistor Sip Pack Inverter, HEX (74LS04) Latch, Octal Shockey (74LS374) 15-10001-001 | RAM 16K x1 Dynamic (4116) 26-00001-016 | Socket DIP 16 Pin for U26 15-10001-001 | RAM 16K x1 Dynamic (4116) Socket DIP 16 Pin for U27
[26-00001-016 {Socket DIP 16 Pin for U10 J6 — |25-00001-001 | Connector, 50 Pin Header Vertical 15-10001-001 | RAM 16K x1 Dynamic (4116)
| J19 | _|25-00002-002 | Connector, 2 Pin .156 Center | 26-00001-016 |
wt [25-00021-002 [Connector .1 Center for W1
| [wi | [ee-00007-001 | [snorting in | = |
| eee | P.C.B. Video Processor Board | [ wai [15-10001-001 [RAM 16K x1 Dynamic (4116) | |
| U1_[15-20245-001 | [Bus Transiciever, Octal (741S245) | [ _|[26-00001-016 | Socket OIP 16 Pin for 31 | |
| U2_[15-20245-001 | [Bus Transiciever, Octal (74LS245) | | u32|15-10001-001 [RAM 16K x1 Dynamic (4116) | | |
3 Ram 1K x 4 NMOS Static (2114) ‘Socket DIP 18 Pin for U3 33 | 15-10001-001 | RAM 16K x1 Dynamic (4116)
| ua | Ram 1K x 4 HMOS Static (2114) | | __[26-00001-016 | Socket DIP 16 Pin for U33. |
Socket DIP 18 Pin for U4 |_u34 [15-20374-001 | Latch, Octal (74LS374)
| U5 | Multiplexer Quad 2-Input (74LS157) | 15-20153-001 | Multiplexer, Dual 4-Input (74L$153) | |
| U6 | Multiplexer Quad 2-Input (74LS157) | U36 | 15-20074-001 | Flip Flop Dual-D (74LS74) | |
| {U7 | Flip Flop, Dual D (74LS74) | U37 [15-20008-001 | Quad, 2-Input and (74LS08) | |
| us | Quad 2 Input or (74LS32) | U38 [15-70113-001 | Flip Flop JK Schottky (74LS113) | _| |
| ug | Quad 2 Input or (741532) | u39 | 15-20004-001 | Inverter, HEX (74LS04) | |
| U0 [15-10001-001 | [RAM 16K x 1 Dynamic (4116) | 40 [15-30017-001 | Butfer/Driver, HEX (7417) |
U41 | 15-10001-001 RAM 16K x 1 Dynamic (4116) 26-00001-016 Socket DIP 16 Pin for U41
wwKU rnuussoun FIGURE 8
DESCRIPTION SYM DESCRIPTION RAM 16K x 1 Dynamic (4116) U8t }15-20157-001 Multiplexer Quad 2-Input (74LS157) 26-00001-016 | Socket DIP 16 Pin for U42 u82 '15-00002-001 | Microprocessor 68A09E 15-10001-001 RAM 16K x 1 Dynamic (4116) 26-00001-040 | Socket DIP 40 Pin for U82 Socket DIP 16 Pin for U43 U83 [15-20244-001 | Octal, Buffer (7415244) RAM 16K x 1 Dynamic (4116) 15-20244-001 | Octal, Buffer (74LS244) Socket DIP 16 Pin for U44 '15-10002-001 | RAM 1K x 4 CMOS Static (6514) 15-10001-001 | RAM 16K x 1 Dynamic (4116) 126-00001-018 | Socket DIP 18 Pin for U8S Socket DIP 16 Pin for U45 H5-10002-001 | RAM 1K x 4 CMOS Static (6514) RAM 16K x 1 Dynamic (4116) Socket DIP 18 Pin for U86 26-00001-016 | Socket DIP 16 Pin for U46 15-20139-001 | Decoder Dual 1 of 4 (7415139) 15-10001-001 | RAM 46K x 1 Dynamic (4116) 15-20032-001 | Quad 2-Input of (741532) Socket DIP 16 Pin for U47 15-20074-001 | Flip Flop, Dual-D (74LS74) 15-10001-001 | RAM 16K x 1 Dynamic (4116) 15-20004-001 | Inverter, HEX (74LS04) 26-00001-016 | Socket DIP 16 Pin for U48 15-20374-001 | Latch, Octal (74LS374) 15-20032-001 | Quad 2-Input or (74LS32) 15-20374-001 | Latch, Octal (74LS374) 15-20086-001 | Quad 2-Input Exclusive or (74LS86) [_u93 |15-20374-001 Latch, Octal (7415374) 15-20086-001 | Quad 2-Input Exclusive or (74LS86) U94 15-20374-001 | Latch, Octal (74LS374) 15-20153-001 | Multiplexer, Dual 4-Input (74LS153) U95 |15-20299-001 | Shift Register 8 Bit (74LS299) 15-20153-001 | Multiplexer, Dual 4-Input (74LS153) '15-20299-001 U96 Shift Register 8 Bit (74LS299) 15-20153-001 | Multiplexer, Dual 4-Input (74LS153) UQ7 }15-20244-001 | Buffer, Octal (74LS244) 15-20157-001 Multiplexer, Quad 2-Input (74LS157) 115-20244-001 | Buffer, Octal (74LS244) RAM 1K x 4 HMOS Static (2148) 15-20138-001 | Decoder, 1 of 8 (74LS138) Socket DIP 18 Pin for US6 U100/15-40000-001 | Quad 2-Input NOR (74C00) RAM 1K x 4 HMOS Static (2148) | U101]15-20008-001 | Quad 2-Input AND (74LS08) 26-00001-018 | Socket DIP 18 Pin for US7 U102[15-20010-001 | Triple 3-Input AND (74LS10) 15-30017-001 | Buffer/Driver, HEX (7417) U103|15-20000-001 | Quad 2-Input NAND (74LS00) 15-10001-001 | RAM 16K x 1 Dynamic (4116) U104]15-20157-001 | Multiplexer Quad 2-Input (74LS157) 15-10001-001 | RAM 16K x 1 Dynamic (4116) U105]15-20299-001 | Shift Register 8 Bit (7415299) 15-10001-001 RAM 16K x 1 Dynamic (4116) U106|15-20299-001 | Shift Register 8 Bit (74LS299) 15-10001-001 | RAM 16K x 1 Dynamic (4116) U107|15-20299-001 | Shift Register 8 Bit (74LS299) 15-10001-001 | RAM 16K x 1 Dynamic (4116) U108|15-20299-001 | Shift Register 8 Bit (74LS299) 15-10001-001 | RAM 16K x 1 Dynamic (4116) U109|15-20299-001 | Shift Register 8 Bit (74LS299) 15-10001-001 | RAM 16K x 1 Dynamic (4116) U110[15-20299-001 | Shift Register 8 Bit (74LS299) 15-10001-001 | RAM 16K x 1 Dynamic (4116) 15-20032-001 | Quad 2-Input or (74LS32) 15-20244-001 | Octal Buffer (74LS244) 15-20245-001 | BUS Transciever, Octal (74LS245) 15-20374-001 | Latch, Octal (74LS374) 15-20374-001 | Latch, Octal (7415374) 15-20374-001 | Latch, Octal (74LS374) 15-20157-001 Multiplexer Quad 2-Input (74LS157) 15-20157-001 Multiplexer Quad 2-Input (74LS157) 15-20245-001 | BUS Transciever, Octal (74LS245) U76 | 15-20273-001 | Register 8 Bit (74LS273) U77 | 15-20373-001 | Latch, Octal (74LS373) 15-20373-001 | Latch, Octal (74LS373) U79 | 15-20373-001 | Latch, Octal (74LS373) U80 | 15-20373-001 | Latch, Octal (74LS373)
TAITO iYM | PART NO. FIGURE 9
DESCRIPTION ‘SYM | PART NO. OESCRIPTION
| 1 | [11-00001-473 | Resistor 47K YW +5% | 17-00001-001 | Ferrite Bead |
| 32 | | 11-00001-332 | Resistor 3.3K YW +5% | 17-00001-001 | Ferrite Bead |
33 | 11-00001-332 | Resistor 3.3K 4W +5% 17-00001-001 | Ferrite Bead
| 34 | | 11-00001-332 | Resistor 3300 OHM %W +5% | FB10 | 17-00001-001 | Ferrite Bead |
%5 | 11-00001-472 | Resistor 4.7K 4W +5% FB11 | 17-00001-001 | Ferrite Bead %6 | 11-00001-103 | Resistor 4.7K 4W +5% FB13 | 17-00001-001 | Ferrite Bead
| 37 | | 11-00001-103 | Resistor 10K %4W +5% | FB14 | 17-00001-001 | Ferrite Bead |
11-00001-332 | Resistor 3.3K OHM YW +5% FB15 | 17-00001-001 Ferrite Bead 11-60001-502 | Pot, P.C. Mount SK FB16 | 17-00001-001 Ferrite Bead 11-00001-473 | Resistor 47K %W +5% FB17 | 17-00001-001 Ferrite Bead 11-00001-473 | Resistor 47K 4W +5% FB18 | 17-00001-001 Ferrite Bead 11-00001-332 | Resistor 3.3K %W +5% FB19 | 17-00001-001 Ferrite Bead 11-00001-332 | Resistor 3.3K YW +5% FB20 | 17-00001-001 Ferrite Bead 11-00001-332 | Resistor 3.3K %W +5% 12-10002-104 Capacitor Ceramic .1uf 50V Axial Lead 11-00001-332 | Resistor 3.3K ¥4W +5% 12-10002-104 Capacitor Ceramic .1uf SOV Axial Lead 11-00001-682 | Resistor 6.8K YW +5% 12-10002-104 Capacitor Ceramic .1uf 50V Axial Lead 11-00001-332 | Resistor 3.3K OHM %4W +5% 12-10002-104 Capacitor Ceramic .1uf SOV Axial Lead 318 | 11-00001-124 | Resistor 120K YW +5% 42-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead 219 | 11-00001-472 | Resistor 4.7K YeW +5% 6 | 12-10002-104 | Capacitor Ceramic .1uf SOV Axial Lead
| R20 | |11-00001-221 | Resistor 220 OKM %W +5% | C7 | 42-20001-107 | Capacitor Electrolytic 100uf 16V |
| R21 | |11-00001-221 | Resistor 220 OHM YW +5% | 8 | | 12-20001-107 | Capacitor Electrolytic 100uf 16V |
| R22 | 11-00001-332 | Resistor 3.3K ¥4W +5% | C9 | | 12-20001-107 | Capacitor Electrolytic 100ut 16V |
R24 | 11-00001-182 | Resistor 1.8K %W +5% C10 | 12-20001-107 | Capacitor Electrolytic 100uf 16V R25 | 11-60001-104 | POT, P.C. Mount 100K C11 | 12-20001-107 | Capacitor Electrolytic 100uf 16V R26 | 11-00001-103 | Resistor 10K %W +5% 7 C12 | 12-10002-104 | Capacitor Ceramic .1uf SOV Axial Lead R27 | 11-00001-103 | Resistor 10K %4W +5% C13 | 12-10002-104 | Capacitor Ceramic . uf SOV Axial Lead R28 | 11-00001-223 | Resistor 22K 4W =+5% C14 | 12-10002-104 | Capacitor Ceramic .1uf SOV Axial Lead
| R29 | 11-00001-562 | Resistor 5.6K %W +5% | | | C15 | |12-10002-104 | Capacitor Ceramic .1uf SOV Axial Lead |
R30 | 11-00001-332 | Resistor 3.3K %W +5% C16 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead R31 | 11-00001-020 | Resistor 2.2 OHM %W +5% C17 eset Capacitor Ceramic .1uf 50V Axial Lead R32 | 11-00001-010 | Resistor 1 OHM %W +5% 18 | 12-10002-104 | Capacitor Ceramic .1uf SOV Axial Lead R33 | 11-00001-020 | Resistor 2.2 OHM YW +5% C19 | 12-10003-470 | Capacitor 47pt 10% NPO Axial Lead R34 | 11-00001-010 | Resistor 1 OHM %W +5% 20 | 12-20001-105 | Capacitor Electrolytic 1uf R35 | 11-00001-102 | Resistor 1.0K OHM YW +5% 21 | 12-10002-104 | Capacitor Ceramic .1ut 50V Axial Lead R36 | 11-00001-332 | Resistor 3.3K ¥4W +5% 22 | 12-20001-807 | Capacitor Electrolytic 800uf, 16V 41-00001-152 | Resistor 1.5K ¥aW +5% C23 | 12-20001-807 | Capacitor Electrolytic 800uf, 16V 11-00001-222 | Resistor 2.2K %W +5% 24 | 12-10001-471 | Capacitor Ceramic 470pt 50V 10% Axial Lead R39 | 11-00001-221 | Resistor 220 OHM “MW «5% 25 | 12-10001-471 | Capacitor Ceramic 470pf SOV 10% Axial Lead R40 | 11-00001-332 | Resistor 3.3K YW +5% €26 | 12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead
| R41 | 11-00001-562 | Resistor 5.6K YsW +5% | | | 27 | 12-10001-471 | Capacitor Ceramic 470pt SOV 10% Axial Lead |
R42 | 11-00001-223 | Resistor 22K YW +5% €28 | 12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead R43 | 11-00001-103 | Resistor 10K %W +5% €30 | 12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead
| R44 | [11-00001-103 | Resistor 10K YW +5% | 31 | 12-10001-471 | Capacitor Ceramic 470pt SOV 10% Axial Lead |
R45 | 11-00001-103 } Resistor 10K %W +5% 32 | 12-10001-471 | Capacitor Ceramic 470pf SOV 10% Axial Lead R50 | 11-00001-472 | Resistor 4.7K YW +5% 33 | 12-10002-104 | Capacitor Ceramic . uf 50V Axial Lead FB1 | 17-00001-001 | Ferrite Bead €34 | 12-10002-104 | Capacitor Ceramic . 1uf SOV Axial Lead |FB2 | 17-00001-001 | Ferrite Bead C35 | 12-10002-104 | Capacitor Ceramic .1uf SOV Axial Lead FB3 | 17-00001-001 | Ferrite Bead 36 | 12-10002-104 | Capacitor Ceramic . tut SOV Axial Lead FRA 17-n0nN1-0N1 | Ferrite Read
FIGURE 9
TAITO PART NO. DESCRIPTION TAITO PART NO. DESCRIPTION 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead 59-00021-001 Test Point 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead 59-00021-001 Test Point 12-10001-123 | Capacitor Ceramic .012 50V Axial Lead 59-00021-001 Test Point 12-10001-183 | Capacitor Ceramic .018 50V Axial Lead 59-00021-001 Test Point 12-10004-103 | Capacitor Ceramic .O1uf 50V Axial Lead 59-00021-001 Test Point 12-10002-104] Capacitor Ceramic . 1uf SOV Axial Lead 59-00021-001 Test Point 12-10001-153 | Capacitor Ceramic .015uf 50V Axial Lead 59-00021-001 Test Point 42-10001-105 | Capacitor Ceramic . 1uf SOV Axial Lead 59-00021-001 Test Point
12-10003-100 12-10002-104 12-20001-105 Capacitor 10pf NPO Axial Lead Capacitor Ceramic .1uf 50V Axial Lead Capacitor Electrolytic 1uf Axial Lead 59-00021-001 Test Point 11-50001-332 Resistor Sip Pack 3.3K 11-50001-332 Resistor Sip Pack 3.3K 12-20001-105 } Capacitor Electrolytic 1uf Axial Lead 11-50001-471 Resistor Sip Pack 47K 12-10001-471 | Capacitor Ceramic 470uf SOV Axial Lead 11-50001-471 Resistor Sip Pack 47K 12-10001-471 | Capacitor Ceramic 470pf SOV Axial Lead 11-50001-103 Resistor Sip Pack 10K 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead 11-50001-332 Resistor Sip Pack 3.3K 15-20244-001 Octal Buffer (74LS244) 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead 0002-104 | Capacitor Ceramic .1uf 50V Axial Lead 15-00002-001 Microprocessor 68A09E Capacitor Ceramic .1uf 50V Axial Lead 26-00001-040 Socket 40P DIP-For 68A09E
Capacitor Electrolytic tut 15-20244-001 Octal Buffer (74LS244) Capacitor Ceramic .1uf 50V Axial Lead 15-20244-001 Octal Buffer (74LS244) Capacitor Electrolytic 470uf, 16V 15-00007-001 Microprocessor 6802 Capacitor Electrolytic 470uf, 16V 26-00001-040 Socket 40P DIP for 6802 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead 15-20244-001 Octal Buffer (74LS244) 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead 15-00004-002 Parallel 1/0 6821
12-10001-471 Capacitor Ceramic 470pf 50V 10% Axial Lead 15-00004-002 Parallel 1/0 6821
12-10001-471 Capacitor Ceramic 470pf 50V 10% Axial Lead 15-20245-001 BUS Tranciever. Octal (74LS245)
12-10001-471 Capacitor Ceramic 470pf 50V 10% Axial Lead 15-20244-001 Octal Buffer (74LS244) Capacitor Ceramic 470pf 50V 10% Axial Lead 15-20245-001 BUS Tranciever, Octal (74LS245) 12-10001-471 Capacitor Ceramic 470pf SOV 10% Axial Lead 15-20244-001 Octal Buffer (74LS244) 12-10001-471 Capacitor Ceramic 470pf 50V 10% Axial Lead 15-50001-001 Digital to Analog Converter 8 Bit (1408)
12-10001-471 Capacitor Ceramic 470pf 50V 10% Axial Lead 15-20032-001 Quad 2-Input or (74LS32) 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead 15-10003-001 RAM 1K x 4 NMOS Static (2114) 12-10002-104 | Capacitor Ceramic .1uf SOV Axial Lead 26-00001-018 Socket 18P DIP for 2114 | C70 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead 15-10003-001 RAM 1K x 4 NMOS Static (2114) | C71 | 12-10002-104 | Capacitor Ceramic .1uf SOV Axial Lead 26-00001-018 Socket 18P DIP for 2114 C72 | 12-10003-101 | Capacitor 100pt 10% NPO Axial Lead 15-20138-001 Decoder 1 of 8 (74LS138) C73 | 12-10003-221 | Capacitor 220pf 10% NPO Axial Lead 15-50003-001 Quad OP AMP LM324
C74 Capacitor Ceramic .1uf SOV Axial Lead 15-60004-001 Speech Synthesis TMS5200 C75 | 12-20001-105 Capacitor Electrolytic tut 26-00001-028 Socket 28P DIP for TMS5200 C76 | 12-20001-105 | Capacitor Electrolytic 1ut 15-00004-001 Parallel VO 68A21
C77 12-10002-104 | Capacitor Ceramic .1uf SOV Axial Lead 15-60002-001 Line Driver (MC1488) C78 | 12-10002-104 | Capacitor Ceramic .1uf SOV Axial Lead 15-00005-002 Serial 0 68A50 C79 | 12-10002-104 | Capacitor Ceramic .1uf SOV Axial Lead 26-00001-024 | Socket 24P DIP for 68A50 C80 | 12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead 15-20004-001 | Inverter, HEX (74LS04) C81 | 12-10001-471 | Capacitor Ceramic 470pf SOV 10% Axial Lead 15-44066-001 | Quad Analog Multiplexer (4066) C83 _ | 12-30001-106| Capacitor Tant, 10uf. 16V 15-60001-001 | Line Receiver (MC 1489) TP1 | 59-00021-001 | Test Point 15-20161-001 | Counter 4-Bit Presettable (74LS161) TP2 59-00021-001 | Test Point 15-20092-001 Counter Divide By Twelve (74LS92)
15-44066-001 Quad Analog Multiplexer (4066)
DATA/SOUND PROCESSOR FIGURE 9
TAITO PART NO. DESCRIPTION 15-50002-001 | Audio Amplifier (2002) 30-00001-001 } Heatsink to 220 15-50002-001 | Audio Amplifier (2002) 30-00001-001 | Heatsink to 220 29-00001-001 | Switch, DIP 4 Pole 19-00002-001 | Crystal 7.3728 MHZ 14-23904-001 | Transistor NPN, Silcon 2N3904 25-00002-004 | Connector 14 PIN Locking 25-00001-001 | Connector Header 50 PIN 25-00001-001 | Connector Header 50 PIN 25-00002-005 | Connector 5 PIN Locking 25-00002-005 | Connector 5 PIN Locking 25-00003-001 | Connector RS232 YM
FIGURE 10
~ | TANTO | TAITO
| SYM | PART NO. | DESCRIPTION | SYM PART NO. | DESCRIPTION |
R1 | 11-00001-562 | Resistor 5.6K, 4W +5% R51 | 11-00001-471 | Resistor 470 OHM %W +5% R2 | 11-00001-471 | Resistor 470 OHM %4W +5% R52 | 11-00001-562 | Resistor 5.6K, %“W +5% R3_ | 11-00001-471 | Resistor 470 OHM %4W +5% R53 | 11-00001-562 | Resistor 5.6K, %4W +5% R4 | 11-00001-471 | Resistor 470 OHM YW +5% R54 | 11-00001-471 | Resistor 470 OHM %W +5% R5 | 11-00001-471 | Resistor 470 OHM YW +5% R55 | 11-00001-471 | Resistor 470 OHM YW +5% R6 | 11-00001-471 | Resistor 470 OHM %4W +5% R56 | 11-00001-471 | Resistor 470 OHM %4W +5% R7 | 11-0000%-471 | Resistor 470 OHM %W +5% R57 | 11-00001-471 | Resistor 470 OHM %W +5% R8 | 11-00001-471 | Resistor 470 OHM %W +5% R58 | 11-00001-471 | Resistor 470 OHM %W +5%
| RQ “[r-00007-474 | Resistor 470 OHM YW +5% | R59 | 11-00001-471 | {Resistor 470 OHM %W +5% |
| R10 | 11-00001-471 | Resistor 470 OHM %W +5% | R6O | 11-00001-471 | |Resistor 470 OHM YW +5% |
R14 | 11-00001-471 | Resistor 470 OHM %4W +5% R61 | 11-00001-471 | Resistor 470 OHM YW +5% R12 | 11-00001-471 | Resistor 470 OHM %4W +5% R62 | 11-00001-471 | Resistor 470 OHM YW +5%
| R13 | 11-00001-471 | Resistor 470 OHM %4W +5% | R63 | 11-00001-471 | |Resistor 470 OHM %W +5% |
| R14 | 11-00001-471 | Resistor 470 OHM “W +5% | C1 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead |
R15 | 11-00001-471 | Resistor 470 OHM %4W +5% C2 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead R16 | 11-00001-471 | Resistor 470 OHM %W +5% C3 | 12-10001-471 [Capacitor Ceramic 470pt Axial Lead
| R17 | 11-00001-471 | Resistor 470 OHM “MW +5% | C4 | 12-10001-471 | |Capacitor Ceramic 470pf Axial Lead | |
| R18 | 11-00001-471 | Resistor 470 OHM YW +5% | C5 | 12-10001-471 | |Capacitor Ceramic 470pf Axial Lead | |
| {R19 | 11-00001-471 | [Resistor 470 OHM %4W +5% | C6 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead | |
| R20 | 11-00001-562 | Resistor 5.6K, 4W +5% | C7__| | 12-10001-471 | |Capacitor Ceramic 470pf Axial Lead |
| R21 | 11-00001-562 | Resistor 5.6K, %W +5% | C8 | 12-10001-471 | |Capacitor Ceramic 470pf Axial Lead | |
| R22 | 11-00001-562 | Resistor 5.6K, %W +5% | C9 | 12-10001-471 | |Capacitor Ceramic 470pf Axial Lead |
R23 | 11-00001-562 | Resistor 5.6K, 44W +5% 42-10001-471 | Capacitor Ceramic 470pf Axial Lead
| R24 | 11-00001-562 | Resistor 5.6K, YW +5% | 12-10001-471 | {Capacitor Ceramic 470pf Axial Lead |
| R25 | 11-00001-562 | Resistor 5.6K, 4W +5% | 12-10001-471 | |Capacitor Ceramic 470pf Axial Lead |
| R26 | 11-00001-562 | Resistor 5.6K, “W +5% | 12-10001-471 | |Capacitor Ceramic 470pf Axial Lead |
| R27 | 11-00001-562 | Resistor 5.6K, %4W +5% | 12-10001-471 | }Capacitor Ceramic 470pf Axial Lead |
| R28 | 11-00001-471 | Resistor 470 OHM %W +5% | 12-10001-471 | |Rapacitor Ceramic 470pt Axial Lead |
R29 | 11-00001-471 | Resistor 470 OHM %W +5% 12-10001-471 | Capacitor Ceramic 470pf Axial Lead
| R30 | 11-00001-471 | Resistor 470 OHM %W +5% | 12-10001-471 | |Capacitor Ceramic 470pt Axial Lead |
| R31 | 11-00001-471 | Resistor 470 OHM %W +5% | 12-10001-471 | |Capacitor Ceramic 470pf Axial Lead |
R32_ | 11-00001-471 | Resistor 470 OHM %W +5% 12-10001-471 | Capacitor Ceramic 470pf Axial Lead
| R33_ | 11-00001-471 | Resistor 470 OHM %W +5% | 12-10001-471 | {Capacitor Ceramic 470pf Axial Lead |
| R34 | 11-00001-471 | Resistor 470 OHM %W +5% | 12-10001-471 | |Capacitor Ceramic 470pf Axial Lead |
11-00001-471 Resistor 470 OHM %W +5% 12-10001-471 Capacitor Ceramic 470pf Axial Lead 11-00001-471 Resistor 470 OHM %W +5% 12-10001-471 Capacitor Ceramic 470pf Axial Lead 11-00001-471 Resistor 470 OHM %W +5% 12-10001-471 Capacitor Ceramic 470pf Axial Lead
11-00001-471 [Resistor 470 OHM %W +5% 12-10001-471 Capacitor Ceramic 470pf Axial Lead 11-00001-471 [Resistor 470 OHM YW +5% 12-10002-104 Capacitor Ceramic .1uf Axial Lead 11-00001-562 Resistor 5.6K, ¥4W +5% 12-10002-104 Capacitor Ceramic .1uf Axial Lead 11-00001-562 Resistor 5.6K, “4W +5% 12-10002-104 Capacitor Ceramic .1uf Axial Lead 11-00001-562 Resistor 5.6K, ¥4W +5% 12-10002-104 Capacitor Ceramic .1uf Axial Lead
11-00001-562 Resistor 5.6K, YW +5% 12-10002-104 Capacitor Ceramic .tuf Axial Lead 11-00001-471 Resistor 470 OHM %W +5% 12-10002-104 Capacitor Ceramic .1uf Axial Lead 11-00001-471 Resistor 470 OHM %4W +5% 12-10002-104 Capacitor Ceramic .1uf Axial Lead
11-00001-471 Resistor 470 OHM %4W +5% 12-10002-104 Capacitor Ceramic .1uf Axial Lead 11-00001-471 Resistor 470 OHM %W +5% 12-10002-104 Capacitor Ceramic .1uf Axial Lead 11-00001-471 Resistor 470 OHM YW +5% 12-10001-471 Capacitor Ceramic 470pf Axial Lead Resistor 470 OHM YW +5%
KRUM/I/U F.U. AOOLMDLT FIGURE 10 TAITO TAITO PARTNO. | DESCRIPTION PARTNO. | DESCRIPTION Ferrite Bead £-PROM ''KRAM'’™
| Ferrite Bead | 26-00001-024| | Socket 24 Pin Dip for U6 |
Ferrite Bead E-PROM ‘'KRAM''™
| Ferrite Bead | 26-00001-024| | Socket 24 Pin Dip for U7 |
17-00001-001 | Ferrite Bead E-PROM "‘KRAM’'™ 17-00001-001 | Ferrite Bead 26-00001-024 | Socket 24 Pin Dip for US
| 17-00001-001 | Ferrite Bead | ug | E-PROM ‘‘KRAM'’™ |
17-00001-001 | Ferrite Bead 26-00001-024 | Socket 24 Pin Dip for U9
| 17-00001-001 | Ferrite Bead | U10. | E-PROM ‘‘KRAM’'™ |
17-00001-001 | Ferrite Bead 26-00001-024 | Socket 24 Pin Dip for U10 17-00001-001 | Ferrite Bead U11 | 15-00004-001 | Paralell 1/0 68A21
| 17-00001-001 | Ferrite Bead | ui2 | Not Used |
| 13-14001-001 | Diode IN4001 | 26-00001-024| | Socket 24 Pin Dip for U12 |
| 13-14001-001 | Diode IN4001 | U13 | Not Used |
| 13-14001-001 | Diode IN4001 | 26-00001-024| | Socket 24 Pin Dip for U13 |
| 13-14001-001 | Diode IN4001 | U14 | E-PROM ‘‘KRAM’'™ |
13-14001-001 | Diode IN4001 26-00001-024 | Socket 24 Pin Dip for U14
| 13-14001-001 | Diode IN4001 | U15 | E-PROM ‘‘KRAM"'™ |
13-14001-001 | Diode IN4001 26-00001-024| Socket 24P Dip Used for E-PROM
| 13-14001-001 | Diode IN4001 | Ui6 | E-PROM ‘‘KRAM''™ |
13-14001-001 | Diode IN4001 26-00001-024| Socket 24 Pin Dip for U16
| 13-14001-001 | Diode IN4001 | U7 | E-PROM ‘‘KRAM'’™ |
13-14001-001 | Diode IN4001 26-00001-024 | Socket 24 Pin Dip for U17 13-14001-001 | Diode IN4001 E-PROM ‘’KRAM''™ 14-00001-001 | Transistor NPN Darlington TIP120 26-00001-024 | Socket 24 Pin Dip for U18 14-00001-001 | Transistor NPN Darlington TIP120 E-PROM ‘‘KRAM’’™ 14-00001-001 | Transistor NPN Darlington TIP120 26-00001-024 | Socket 24 Pin Dip for U19 14-00001-001 | Transistor NPN Darlington TIP120 15-00004-001 | Paralell I/0 68A21 14-00001-001 | Transistor NPN Darlington TIP120 15-20138-001 | Decoder 1 of 8 (138)
| 14-00001-001} | Transistor NPN Darlington TIP120 | 26-00002-016 | ROM Select |
| 14-00001-001| | Transistor NPN Darlington T!P120 | 26-00001-014 | Socket 24P Dip for U22 |
| 14-00001-001} | Transistor NPN Darlington TIP120 | 15-20004-001 | Inverter, HEX (74LS04) |
Not Used = Not Used
| 14-00001-001| | Transistor NPN Darlington TIP120 | Not Used |
| 14-00001-001| | Transistor NPN Darlington TIP120 | Not Used |
14-00001-001 | Transistor NPN Darlington TIP120 E-PROM ‘‘KRAM''™ 26-00002-016} ROM Select 26-00001-014 | Socket 14P Dip for U27 26-00001-014| Socket 14P Dip, for U1 15-20138-001 | Decoder 1 of 8 (138) 15-20138-001 | Decoder 1 of 8 (138) ROM Select Not Used 26-00001-014 | Socket 14P Dip Used for ROM Select 26-00001-024] Socket 24 Pin Dip for U3 45-00004-001 | Paralell 1/0 6821 Not Used 25-00001-001 | Connector Header SOPIN
| 26-00001-024| | Socket 24 Pin Dip for U4 | 25-00001-001 | Connector Header SOPIN |
E-PROM ‘‘KRAM’'™™ 25-00001-001 | Connector Header SOPIN ket 24 Pin Dip for US 25-00002-014 Connector 14 Pin Header .156 Center 25-00002-014 Connector 14 Pin Header .156 Center 25-00002-014 Connector 14 Pin Header .156 Center 125-000023-014 Connector 14 Pin Header .156 Center
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
FIGURE 12 BOARD LAYOUT
RKXXO OE Yd Fa Fae a a a Say SN] x] [>] a] [>
0} IY VY YYY HOE {es} -(00b+ {0} -[0lb}
Vav 6, cop} 9 fs0ze} Ss 02}
O) -{100b}- Ys tga} sa} WY se ’
Th VIDEO PROCESSOR S34 COIN DOOR Efizrise7esnnn
PCB. 08-00001-001 tove | ff] v0 seononry ewerer (20 vie)
a
MARQUEE
SG "uckrs N)(OO0)_ — _ rransrorwen
DATA /SOUND PCB. 08-00002-001 wining viAunAm FIGURE 11
we —— 97Pa gh ez | a eS a3} & Eas os) 25) “PFO 1@t
14s =>"
+
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.