Cosmo Gang Preliminary Manual
Cosmo Gang (US) (Namco (Data East license), 1990) · Manual · 41 pages · 17 sections · original scan
PRELIMINARY MANUAL
DE DATA EAST USA, INC.
) 1850 Little Orchard Street
WB San Jose, California 95125 Telephone (408) 286-7080
COSMO GANG
The COMO GANG* final version Service Manual has not been completed yet. When the final version of the manual is completed we will mail a final version to you. Please, fill out the informations listed below and mail to:
DATA EAST USA, INC. 1850 Little Orchard St. San Jose, Ca. 95125 Attention: Customer Service
Or call DATA EAST Customer Service at (408) 286-7080. We will answer most of technical questions you may have.
COMPANY NAME:
ADDRESS:
CITY: STATE, ZIP:
PCB SERIAL NUMBER:
GAME CABINET SERIAL NUMBER:
2.
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10) When transporting or moving the machine, Be sure to separate the cabinet from the Gun Console.
Do not drop or give a strong shock (especially to the character box).
This machine is designed for indoor use only. Do not install this machine outdoor.
Install the machine on a solid level surface spaced an
appropriate distance.
Do not install the machine on an unstable surface or on
a floor with vibration.
Do not install the machine in areas directly exposed to the sunlight or with much moisture or dust. Avoid installing it near heating systems to prevent rising temperature inside of the machine.
Do not place the machine near fire equipment or emergency exits or any other places where it would be an obstacle in case of emergency.
Make sure to turn the power off when replacing any parts or connecting / disconnecting the connectors.
Do not attempt to repair the game PCB yourself. Instead, please return the board to your distributor for any repairs. This PCB contains sensitive chips which could be destroved even by the internal voltage of a multi-meter.
Be careful that players, especially children, do not interfere with the characters movements or attempt to reach beyond the side fences. Hands and fingers could be caught, casing injury.
To prevent mischief, this machine is designed to not give a credit if the coin switch is closed longer than the normal
coin passage time.
- INSTRUCTIONS ON GAME
- How to play Cosmo Gangs is a comical shooting game which can be enjoyed by all ages from young children to adults. When the.game starts, 5 characters (Cosmo) move forward trying to steal the energy containers. A player has to shoot a handgun at the inside of the characters (Cosmo) mouth and defend the energy containers from theft. If just one energy container is stolen, the game is over. If a player shoots a handgun at the target while the character (Cosmo) is moving forward or backward dragging the energy container, that character (Cosmo) will be blown away, and the play scores points. There are two stages in a normal game and three stages in a professional game. When a player manages to protect the energy containers for the period set for each stage, he can go to the
next stage. 1 In case of l-player game, only the left handgun can be used. 2 When one coin is inserted ( in case of 1 coin - 1 play ), the select buttons of normal course and professional course will flash on and off. [Ref. Fig. 5-1] These buttons serve both as select buttons and start switches
so make sure to insert 2 coins before pressing the select buttons in case of 2-players game.
Normal course button
Professional course button
Target LED
Instruction panel
Fig. 5-1
Mf Object of games: Defend your ENERGY CUBES by shooting at the approaching COSMO GAN members. DON'T LET THEM TAKE THE ENERGY CUBES BACK TO THEIR SPACE SHIP!
@ The game is over if: |. You win by successfully defending ENERGY CUBES in each stage, or 2 You lose when a COSMO takes an ENERGY CUBE back to his space ship.
M@The easy gare has 2 stage, the hard game has 3.
- Explanation of the SCORE PANEL
1 Stage This indicates the stage in progress.
2 Time This indicates the time left for the stage in progress. 3 Hit Score This indicates the number of the characters ( Cosmo ) hit by the players. 4 Top Score This indicates the highest scores of l-player game and 2-players game, separately, since the power has been turned on.
Score panel Fig.5-2
{ Time setting for each stage and for each course ] else ee lormal course | 40 sec. | sec. | 20 sec. Professional course a sec. 30 sec.
- There is no difference in time setting between l-piayer and 2-players game.
The Service Panel is located inside the coin door assembly. The service Panel inciudes:
COIN COUNTER. Increments once for a coin dropped through either coin slot.
VOLUME CONTROL. Adjusts the overall loudness of game sounds. This control is preset for mid range at the factory.
SERVICE SWITCH. (The upper switch on the panel) Can be used to start the game without incrementing the coin counter.
TEST SWITCH. (The lower switch on the panel) Used for the TEST MODE of the game. See TEST MODE description in this manual.
Volume Coin Councer
- CHANGING THE GAME DIFFICULTY The difficulties of the game and the game made are changed by dip switch (4P. DIPSW) on the game PCB. . {Ref. Table 6-1, Fig. 6-2]
STATE OF DIP SWITCH (4P. DIPSW)
————$ — cq _—_
STATE OF SWITCH
| a | CONTENT | y | 2/3 | 4 | |
| EASY | peter{ | [| | \ sound volume | |
| a | a | oF | i: | Jai] | |
| DIFFI- | fn | ks jg aP-DIPSH | ||
| CULTIES | off | on | ! | Ct | pp-pirse | |
| DIFFICULT on | on | | | Ost. | eppipse |
____} ne aa COIN MODE | GAME sODg oF a2 FREE PLAY| on | es
| TICKET- | No | | | OFF |
PRIZE |
| SPECIFIC] | vES | | | on | | |
- CHANGING THE GAME PRICING Game fees and attract play, etc. can be changed by the dip switch (8P. DIPSW) on the game PCB.
; [Ref. Table 6-2, Fig. 6-2]
STATE OF DIP SWITCH (8P. DIPSW)
Tata OF SWITCH (7, 8 unused)
se A
OFF | OFF
- 1OOINZPLAYER|| on | off COIN] PLAYER || off | on 3COIN] PLAYER || on | on ves OFF
TICKET. 5 PRIZE 20 TICKET, TICKET 10 on | off
PRIZE PRIZE 40
POINT, SETTING TICRET 15 off on PRIZE 60°.
- Capital letter are the original setting. **Foreign mode
- USING THE SERVICE SWITCH Games can be played without incrementing the coin counter by pressing this switch. Please use this switch when repairing or adjusting. {Ref. Fig. 6-1]
- USING THE TEST SWITCH Pressing the test switch while in the state of waiting for for coin, enters the test mode. Press the normal startbutton to go to the next test. Please use this switch when repairing or adjusting. [Ref. Table 6-3, Fig. 6-1]
TEST MODE
Test Operation
horor Solenoid Test Operation in order of deor panel character, container and lock-out solenoid. ——__—_._! Lamp Test -|| Head lamp, bess spot lamp, cosm spot lamp, start lamp eet aD as lam flash on and off. i LED_and winning lam flash onand off. Xenon Lamp When handgun flashes and the characteris shot, the | Sensor Test Mumber of the character hit will be cated. i = { i
Switch Test
lex] On case of aiming at No. 1 High score indicate ll. When it continues to hit, the figure will change like 2, 13... . When two guns hit two characters at the same tim, the the lower number of characterwill be indicated as the order of priority is set fram No. 1. This test automatically goes to the next test without pressing the nommal start button when 1 minute has passed. 7 segment LED of the score PCS indicates irom 0 to 9.
test switch. When the switch is closed, voice synthesis sound is outoputted. | View Synthesis Test ||Voice synthesis sound is outputted in turn. When all = |
: sounds are through, it goes to the next test automatically:
| Music Test Music is outputted in tum. When all music is outputted, } it goes to the next test automatically. ee Drive Test Characters go back and forth between the hame station Hy and the position of the containers by turns starting i fram No. 1. *Characters are numbered 1 to 5 from the left.
TABLE 6-3
(6)ERROR INDICATIONS AND THE POSSIBLE SOLUTIONS When there is something wrong with this machine error messages are indicated automatically on the displays. While voice synthesis sounds of the handgun go off and on. tries to get rid of the errors comes back to the attract mode.
ERRORS AND POSSIBLE SOLUTIONS
ar Exror Indication | ERRORS [i , Every window of Door panel won't the score panel open. shows 1 Signals from the Limit switch of the upper door drive assy can't be sensed. {
i } H !
lu can't go forward. Top score shows L can't go forward Character No. 3
| Top score shows : Character No. 5 ae) : can't go forward
“21 cant go backward Top score shows | Character No. 2 22 { can't go a
Every window of | Door panel won't the score panel = close.
shows Signals from the Same as above
limit switch of the lower door @rive assy can't be sensed. Top Scare shows , Character No. 1 (CHEGK fo"See IF Gath CHETSCISE WORKS ——]
Gnaracter No. 2 \are connected correctly there might be
—:—jUse the dip switch (6P, DIPSW) In this circumstance, the auto-retum fimetion works and up to 3 times. If it clears the error, it | (Reg. Table 6-4)
a
Turn the power GFF and ON again and confirm the doar panel moves. If it does not move, check fuse Fl inside of the character box. In case that the fuse is OK, the motor or PCB may be bad, consult with your If there is a samething wrong with the door panel, manually push the door panel open, disconnect the motor connectors, and cover both the upper and the lower limit switches to playgames.
correctly in the test mode. If it does not, although the connectors
motor trouble, PCB failure or broken spring consult with your distributor. in case that a character drive system has troubles, games can be played mly ith the operating characters. By
(Characters with ON will not be used) H
off before changing any switches. Qn arder to avoid secondary trouble, the connectors of the motor, character assy and container assy, corresponding
Fix the container and character in these proper-places with marking tape. (Ref. Fig. 6-3, 6-4] *Characters are mmbered 1 to 5 fram the ane on the left. a
GUM TAP CHARACTER ASSY (TO FIX AT THE REAR)
MOTOR (STEPPING) (TO RELEASE CONNECTOR (6P) ) Fig.. 6-4
1°
- DAILY MAINTENANCE
- Be sure to turn the power off before procedures. (CAUTION] When replacing the character assy and the drive assy, turn the power off once, and turn the power on again to open the door panel. When it is fully open, turn the power off again to replace the assembly.
- Replacing the Character Assy @Move the container assy's(5) from the front field toward the character box by pressing the hook post of the lock arms. {Ref. Fig. 7-1]
' @ Remove the front field (M6 button bolt, washer : 2sets) (Ref. Fig. 7-2]
@Move the container assy's(5) toward the cockpit again.
@ Remove two field (main fields of right/lefct field) on either side of the character assy to be replaced. [Ref. Fig. 7-3}
@®Move the character assy to be replaced forward, remove the harness cover (M5 nut : 2 sets) and pull our the connector (6P). (Ref. Fig. 7-4]
@ Loosen the nuts (M5 nut : 2 sets) which hold the character assy and pull the character assy upward to remove and replace. ([Ref. Fig. 7-5]
Front Field
Light Field
=~, “~ Pe a Ga » a ow @ > a a
Harness Cover
fig. 7-4 fig.7-5
- Replacing the Drive Ass:
@ Follow the steps@-@ of (1) Replacing the Character Assy (Pl 7-(1))
@Remove two fields (main fields or right/left field) on either side of the drive assy to be replaced.
@Disconnect all of the connectors (front side : 6P, 4P, 3P ; stage box side : 4P, 3P) of the drive assy to be replaced.
® Cur the tie-wrap which the mobil harness connecting to the character carrier and the container carrier, and pull out the connector (6P). (After replacement use a new tie-wrap to fix.) (Ref. Fig. 7-6]
1 © Remove the front side bolts (M6 hex bolt : 2) which hold the drive assy, and remove the assembly by sliding it from the rail holder to replace. (Ref. Fig. 7-7] It makes the replacement easier if the bolts (M6 button bolt, washer + 3 sets) which hold the rear field are loosen.
Slide Rail Rear Field Main Fieleé / Caracter Carrier
Harness —a— |
fig. 7-6 Drive Assy Rail Holder fig. 7-7
- Replacing the Mobil Harness Follow the steps@)-@ of (1) Replacing the Character Assy (Pl 7-(1)).
@ Remove two fields (main fields or right/left field) on either side of the drive assy with the mobil harness to be replaced.
@Cut the tie wrap holding the mobil harness from the character carrier or the container carrier, and pull out the connector (6P). (After replacement use a new tie-wrap to fix.)
@ Remove the saddle (M4 Tapping) holding the mobil harness to the botton panel of the cabinet and pull out the connector (6P) to replace. : [Ref. Fig. 7-8]
Sadle
fig. 7-8
- Replacing the Gun Assy Qpen the gun console board on the gun console and pull out the connector (2P) of the gun assy to be replaced.
® Remove the xenon cover (M4 cap screws : 2), and pull out the fiber cap. {Ref. Fig. 7-9]
re) Remove the gun shaft (M9 cap bolt : 1) and pull out the gun assy to replace. (Ref. Fig. 7-10, 7-11]
M4 cup screw | a Gun Console SA
Xenon Cover
Xenon Lamp Assy Fuse Holder
fig.7-9
Gun Console Gun Assy Gun ,Shafe
Gun Cover
M6 Cap bolt Spacer
fig. 7-10 . fig. 7-11
- Replacing the Game PCB @ Open the gun console board and remove the cover (A) (M6 button bolt, washer : 6 sets). Pull out the connector (3P) of the Winning lamp at the same time. : (Ref. Fig. 7-12]
@ Pull off all the connectors on the game PCB and take out the game PCB by removing it from the locking supports (3) to replace. (Ref. Fig. 7-13]
Connector (3p)
PCB Base
Locking
Game PCB
- Replacing the Score PCB @ Open the gun console board and remove the cover (A) (M6 button bolt, washer : 6 sets). Pull off the connector (3P) of the winning lamp at the same time. (Ref. Fig. 7-12]
@ Disconnect the score PCB connector (J10) which is attached to the back of the score bracket (B), and take off the score PCB (M4 cap screw :
- to replace. (Ref. Fig. 7-14]
a score Bracket
Score PCB M4 Cup Ser
Coin-in 7
- Switch Bracket
Coin Selector
fig. 7-14
- Replacing the Xenon PCB @ Open the gun console board and remove the PCB cover (B) of the xenon PCB to be replaced (MS cap screw : 1).
@ Disconnect the connector (4P, 3P) on the xenon PCB, and pull out the xenon PCB to replace. (Ref. Fig. 7-15]
Xenon PCB
fig.
- =
- Replacing the Xenon Lamp Assy Open the gun console board and remove the xenon cover of the xenon lamp to be replaced (M4 cap screw: 2). {Ref. Fig. 7-9]
@ Remove the PCB cover (B) of the xenon PCB to which the xenon lamp assy to be replaced is connected (M5 cap screw : 1) and pull the connector (3P) off. {Ref. Fig. 7-15]
@ Remove the xenon lamp assy from the xenon holder to replace. (Ref. Fig. 7-16]
.. Xenon LampAssy
Fiber Cable
Fuse Holder
Xenon Lamp Holder
fig. 7-16
- Replacing the Boss Character Assy , @ Remove the UFO (A) (M5 button belt, washer : 5 sets). Disconnect the connectors of two head lamps at the same time. [Ref. Fig. 7-17]
@ Disconnect the connector (2P) of the boss character assy, loosen the nuts (M5 nut : 2) which are holding the assy, and pull the boss charac— ter assy upward and out to replace. {Ref. Fig. 7-18]
UFO(A) Head Lamp Cover .
etre. = M5 button bolt o —_ SS eo
Connector(2p) Se SEPA \aen. Boss Character Base Stage Box
fig. 7-17 fig. 7-18 é a #
- Illustrated Parts List
- Character Assy
CHARACTER ASSY LIST
No. | | DESCRIPTION [| xmouxt | PARTS NUMBER
| 1 | CHARACTER(H1) | rl |
| CHARACTER(H2) | . | 244-002 |
CHARACTER (H3) 244-003 ° CHARACTER(H4) 244-004 CHARACTER(HS). 244-005
| CHARACTER(F) | I | 244-006 |
44-00
ong
1 244-009
SHAFT (F) 244-012
a Oo} | wo] ~w
- | FEET) 244-015 “fone 244-016
| 130 | FRAHE(A) | . | . | 1 | 244-017 |
| 14 | FRAME(B)* | 1 | |. 244-018 | |
| 15 | FRAME(C) | 1 | | 244-019 |
BALL LINK 244-020
| 17. | CUSHION | 2 | } 244-021 |
| 18 | SPRING | 1 | | 244-022 |
| 19 | 0 RING | 1 | { 244-023 |
| 20 | FRANGE BUSH | ee eee |
{
| 21 | FRANGE BUSH | 4 | 225-100 |
- | HIT SENSOR PCB 244-024 23° |. SOLENOID(DC) 244-025
- AMOUNT IS FOR 1 ASSY. Ran Fig. 8-
- Drive Assy
fig. 8 - 2
—28.-
DRIVE ASSY LIST [no | pescazerron DESCRIPTION JaMOUNT | PARTS NUMBER |
—— SPACER(A) ARH BUSH ray [Ps [—enanscrer canna [Ty aetcaos I Cc [3 eenencrer supronrea| yaaa [ro |contarnen seacreT [a —=«dt=C eno ——i [n | aaewess cover [teen a [aa sear fatten a Ds ae stoped es fie [_“eusaon romtay__[ 3 SSS eet fir [7 eastzon wenn) [eenity a A ele ra
ray ra
WIRE ROPE 244-118 [is [tention Seemed SC [zo | aieney conraniex [Yee [ar | toreisner srrenen [yeni BEARING 235-057 23 FRANGE BEARING [2 | 244-122 KURATAITO SPRING 244-123 SENEOR PCB MOTOR (STEPPING)
- AMOUNT IS FOR 1 ASSY. 244-025
- Gun Assy
GUN ASSY LIST
| [ wo. | | DESCRIPTION | | amount __| | ||
| P| | unc) | a | rere | |
| : | p22 | | GUN(L) | | o21 | 244-202 |
: ee 244-204 244-205 —— a seu 2442206 244-207 [eww cover | pe [rarer srarng |) aeteane [es] teroce suarn | 1 «dC aaa +d [__6UN suaPr(a) | 1 | Ti] ww sears) a Fo storeencay | yen hs saree) a a Pr
| fe | | sracenay | [age |
a AT feos se a
SWITCH(MICRO) 000-110 XENON LAMP ASSY 1 215-123
- AMOUNT IS FOR 1 ASSY. Fig. 8-3
OTHER REPAIR. PARTS
=z ro)
SIDE FENCE(R) [SIDE FENCE(L) WASHER (@30) ADJUSTER BRACKET
FIELD STICKER MAIN A DESCRIPTION AMOUNT PARTS NUMBER
244-401
244-402
244-403
244-404
244-405 : ran r
: FIELD STICKER MAIN B
FIELD STICKER MAIN C “244-408 “9 FIELD STICKER (RIGHT) 1 ‘| 244-409 _
| 10 | FIELD STICKER (LEFT) | 1 | 244-410 | ||
| Ti | | | COSMO STICKER | 2 | 244-411 |
| 12 | LINE STICKER(A) | 2 | 244-412 | |
| 13 | LINE STICKER(B) | 2 | 244-413 |
i caSTER(FIEED) «4 #2004
| TS | " CASTER(FLEXIBLE) | 102-005 | ‘ |
| 16 | LEVEL ADJUSTER(LARGE)| 2 | 102-033 |
[re soars tee
| 15] | ___UF0(B) | ee ere | |||
| a | [~~ | ~‘DOME | ~ | 1 | 244-418 |
| 22 | LAMP WINDOW < | {1 | 244-419 | | | |
| 73 | TITLE STICKER | 1 | 244-420 | ||
| 2h | STAGE STICKER | 1 | 244—421 | ||
| 75 | CHARACTER (BH) | 1 | 244-422 | ||
| 26 | BOSS ANTHENA | 244-423 |
27 KURATAITO
| 28 | : DOOR PANEL | 1 |
| 29 | LAMP | 10 |
| | 30 | LAMP | 12 |
| {31 | HEAD LAMP COVER — | 2 |
Fig. 8-5 244-406
244-407 “
244-301
002-008
002-117
235-084
GUN CONSOLE PART LIST
x0. | DESCRIPTION PARTS NUMBER
PUNCHING wie
INSTRUCTION PANEL 244-427
SCORE PANEL eye i STAY(L)
0 LEVEL ADJUSTER (SMALL)
i COIN PLATE
15 REPAIR LAMP COVER 1 244-437
Fig. 8-6 L
1 | 244-435 100-015 we w
ac
- TROUBLESHOOTING
- If you suspect the unit may be malfunctioning, turn the power off and check the following points.
@ Be fully alert to mechanical problems. This machine has many mechanical devices. When the machine seems to be malfunctioning, check these mechanical devices because those parts might be loose, shaky, sliding, worn out, or damaged.
@Be alert to loose connections. Malfunctions are often caused by loose connections or soldering failures. Check the connected parts (connectors, solder joints) of the wiring first.
“@Make sure that foreign substances are not in the PCBs. Foreign substances in PCBs may cause improper operation. Check thar the PCBs are clean.
- When troubleshooting, check the wiring diagram.
This will make it easier to troubleshoot and avoid mistake. Refer to paragraphs "6-(5) Using the Test Switch" and "6-(6) Error Indications and Solutions" for troubleshooting.
- Be fully alert to avoiding an electric shock.
- If the above suggestions are not applicable, or no improvement is observed, contact your distributor or one of service offices printed in the ‘back cover of this manual.
- When sending parts to be repaired, make sure to pack them firmly with a complete explanation of the problem. When sending PCBs especially wrap them with sponges or air caps and pack them in cardboard boxes so that they can avoid direct impact from outside during shipment.
DATA EAST U.S.A., INC.
PARTS DEPARTMENT NOTICE
Dear Distributor/Operator:
Attached is a Bill of Materials to help you identify parts needed for replacement on Cosmo Gang. PLEASE NOTE: THIS IS ONLY A PRELIMINARY MANUAL. To obtain a copy of the final manual, please fill out all information on the request form at the beginning of the Cosmo Gang technical manual and a final version of the combined parts/technical manual will be sent to you at no charge.
SHOULD YOU REQUIRE HELP IDENTIFYING PARTS FROM THE ENCLOSED BILL OF MATERIALS, PLEASE CALL:
DATA EAST CUSTOMER SERVICE (408) - 286-7080 X281/280
Dimensions and Weights:
Crated: Uncrate:
117 X 44 X 82 110 - 132 X 37 X 68 1060 Lbs. 825 Lbs,
Current: 5 Amps
Thank you for your cooperation.
Sincerely,
Data East Parts
515-0076-00 CONTROL PANEL ASSY, COSMO Part Number Description
LIST OF MATERIALS
ITEM PART NUMBER REV QTY/ASY QTY/GM DESCRIPTION
| 036-0254-00 | 1 | Harness, Control Panel | |
| 180-0031-00 | 1 | Illuminated Pshbtn w/usw,Small,R,Green | |
| 180-0032-00 | 1 | Ill. Pshbtn w/yusw,Small,R,Orange | |
| 366-0032-00 | 1 | Control Panel | |
| 510~0202-00 | 2 | 2 | Gun Assy |
| 660~-0008-00 | 1 | 1 | Plex, Clear 15" X 11 7/8" |
| 234-0003-05 | 6 | Screw, #8-32 - 1 1/4, Button, Hex, MS | |
| 242-5011-00 | 6 | Washer, Flat #8 | |
| 239-0002-00 | 6 | Nut, Kep, #8-32 | |
| 810-0048-00 | 1 | 1 | Underlay, Instruction |
| 535~-0165-00 | 1 | 1 | Control Panel Retainer |
| 165~0008-00 | 2 | Lamp, #1816, 13V, .33A | |
| 077-5009-00 | 2 | 2 | Miniature Bayonet Socket |
| 040-0003-00 | 6 | Tywrap, 4" | |
| 232-0002-00 | 6 | Screw, Pan, #8 X 1/2 SMS | |
| 242-0019-00 | 2 | 2 | Washer (A), White, Plastic |
| 535-0172-00 | 1 | 2 | Gun Base (C), Top |
| 535-0173-00 | 1 | 2 | Gun Base (D), Bottom |
| 231-0015-06 | 4 | Bolt, Hex Head 5/16 - 18 X 1 1/2" | |
| 231-0004-04 | 4 | Bolt, 5/16 - 18 X 11/2 FH, Phil | |
| 244-0012-00 | 8 | Washer, Split Lock, 5/16 | |
| 238-0015~00 | 8 | Nut, Kep, 5/16 ~ 18 | |
| 234-0011-03 | 6 | Screw, Socket, Hex, #12-24 X 1",MS | |
| 530-0032-00 | 1 | 2 | Gun Shaft (A) |
| 254-0018-00 | 1 | 2 | Spacer (B), ID=.4, OD=.63, t=.41 |
| 234-0012-01 | 2 | 1/4 - 20 X 1/2", Socket Hex Head, MS | |
| 244-0002-00 | 4 | Washer, 1/4 Split Lock | |
| 242-0020-00 | 2. | 2 | Washer, Flat, Fender, ID=1/4, OD=3/4" |
| 285-0006-00 | 1 | 2 | Bumper, Rubber, Black |
| 237-0009-01 | 2 | Screw, Pan Head, Phil,10-24 X 1",MS | |
| 242-0010-00 | 2 | Washer, Fle #10 | |
| 239~0001-00 | 2 | Nut, Kep, 10-24 | |
| 233-0010-02 | 12 | Screw, FH, #10 X 1/2 SMS |
Preliminary : 01-04-91
510-0209-00 FRONT BOX ASSY, COSMO Part Number Description
LIST OF MATERIALS
ITEM PART NUMBER REV QTY/ASY QTY/GM DESCRIPTION
| 036-0239-00 | 1 | 1 | Harness, J5 - J10 (to display) |
| 036-0240-00 | 1 | 1 | Harness, J7- J91 (to fuse pcb) |
| 036-0241-00 | 1 | 1 | Harness, J6 - 387 (from cpu to fuse) |
| 036-0242-00 | L | 1 | Harness, J1 - 389 (from cpu to fuse) |
| 036-0245-00 | 1 | 1 | Harness, J2 - J9 (fr. cpu to ctrl pnl |
| 036-0246-01 | 1 | 1 | Harness, Xenon Tube, Player 1, 26" |
| 036-0246-02 | 1 | 1 | Harness, Xenon Tube, Player 2, 56" |
| 036-0244-00 | 1 | 1 | Harness, J90 (fr.fuse pcb - xenon pcb) |
| 036-0258-00 | 1 | 1 | Harness, J88 (from fuse pcb to P.S) |
| 036-0262-00 | 1 | 1 | Harness, Ticket Dispenser, Cpu Side |
| 036-0263-01 | 1 | 1 | Harness, Ticket Disp., Player 1, 4-S-S |
| 036-0263-02 | 1 | L | Harness, Ticket Disp., Player 2, DL1275 |
| 036-0270-00 | 1 | Harness, Maintenance | |
| 036-0271-00 | 1 | Harness, Lock out coil | |
| 040-0001-00 | 3 | Clamp, Cable, Stickdown | |
| 040-0007-00 | 4 | Clamp, Cable, Nylon, 3/8" | |
| 040-0006-00 | 8 | Clamp, Cable, Nylon, 3/4" | |
| 040-0003-00 | 10 | Tywrap, 4" | |
| 232-0003-00 | 10 | Screw, PH, #6 X 1/2 SMS | |
| 232-0002-00 | 12 | Screw, PH, #8 X 1/2 SMS | |
| 232-0002-01 | 18 | Screw, PH, #8 X 5/8 SMS | |
| 366-0022-00 | 1 | 1 | Front Box |
| 366-0026-00 | 1 | 2 | Ticket Door |
| 231-0007-03 | 8 | #10 - 24 X 11/4 Carriage Bolt | |
| 242-0010-00 | 8 | Washer, Flat, #10 | |
| 239-0001-00 | 8 | Nut, Kep, 10 -24 | |
| 535-0121-00 | 2 | 2 | Trim Plate . |
| 535-0174-00 | 1 | 1 | Xenon Peb Grill |
| 535-0131-00 | 4 | Z Bracket | |
| 232-0007-00 | 4 | Screw, #6-32 X 1/4, PH, MS | |
| 239-0009-00 | 4 | Nut, Kep, #6-32 | |
| 254-0008-00 | 8 | Spacer, Aluminum, ID=3/16, OD=3/8 | |
| 232-0003-01 | 8 | Screw, Phil, #6 X 3/4, SMS | |
| 510-0168-00 | 1 | 1 | Ticket Dispenser, DL-1275 |
| 510-0212-00 | 1 | 1 | Ticket Dispenser, DL-4-S-S |
| e 535-0094-00 | 2 | 4 | Ticket Cartridge |
| 510-0203~-00 | 1 | 1 | Coin Door Assembly w/ lockout coil |
| 535-0178-00 | 2 | . | Speaker Grill (For Ventilation) |
| 510-0200-00 | 1 | 2 | Peb, Xenon Power |
| 520-0106-00 | 1 | 1 | Pcb, Ticket Interface |
| 510-0198-00 | 1 | 1 | Cpu Board |
| 510-0201-00 | 1 | 1 | Fuse Pcb |
| 200-0022-00 | 1 | Fuse, 10A, 125V, Slo Blo | |
| 200-0023-00 | 1 | 1 | Fuse, 20A, Fast Blo |
| 200-0024-00 | 10 | Fuse, 2.5A, 250V, Fast Blo | |
| 515-0076-00 | 1 | 1 | Control Panel Ass |
| 515-0078-00 | 1 | 2 | Xenon Lamp Assy |
510-0209-00 FRONT BOX ASSY, COSMO (Continued) Part Number Description
ITEM PART NUMBER REV QTY/ASY QTY/GM DESCRIPTION 515-0057-00 535-0169-01 535-0169-02 535-0184-00 515-0079-00 515-0081-00 406-0431-01 406-0431-02 406-0432-00 055-0018-00
Preliminary : 01-11-91 PRPPRPRPNPRP Service Panel Assy Bracket, Speaker Panel, Right Bracket, Speaker Panel, Left Bracket, Lock Display Board Assy Win Lamp Panel Assy Label, Ticket Dispenser DL - 1275 Label, Ticket Dispenser DL 4-S-S Label, Xenon Power Pcb Quicksplice, 18-22 AWG #10-24 X 1", Carriage bolt
510-0208-00 BACK BOX ASSY, COSMO Part Number Description
LIST OF MATERIALS
ITEM PART NUMBER REV QTY/ASY QTY/GM DESCRIPTION
| 036-0243-00 | L | 1 | Harness, J3 - J86 |
| 036-0247-00 | 1 | 1 | Harness, J4 (to motors & resistors |
| 036-0250-01 | 1 | 1 | Harness, Energy Box 1 Extension |
| 036-0250-02 | 1 | 1 | Harness, Energy Box 2 Extension |
| 036-0250-03 | 1 | 1 | Harness, Energy Box 3 Extension |
| 036-0250-04 | 1 | i | Harness, Energy Box 4 Extension |
| 036-0250-05 | 1 | 1 | Harness, Energy Box 5 Extension |
| 036-0251-01 | 1 | 1 | Harness, Character 1 Extension |
| 036-0251-02 | 1 | 1 | Harness, Character 2 Extension |
| 036-0251-03 | 1 | 1 | Harness, Character 3 Extension |
| 036-0251-04 | 1 | 1 | Harness, Character 4 Extension |
| 036~0251-05 | 1 | 1 | Harness, Character 5 Extension |
| 036-0255~-00 | 1 | 1 | Harness, J8, (to lamps) |
| 036-0259-00 | 1 | 1 | Harness, Power Supply Extension |
| 036-0267-00 | 1 | 1 | Harness, Coin Door Lamp Extension |
| 040-0003~00 | 20 | Tywrap, 4" | |
| 040-0006-00 | 5 | Clamp, Cable, Nylon | |
| 232-0002-00 | 10 | Screw, PH, Phil, #8 X 1/2 SMS | |
| 366-0023-00 | 1 | 1 | Back Box |
| 366-0027-00 | 1 | a | Side Door |
| 366-0028-00 | 4, | 1 | Rear Door |
| 510-0205-00 | 1 | 5 | Drive Unit Assy |
| 535-0158-00 | 1 | 1 | Bracket, Drive Unit |
| 231-0014-00 | 13 | Bolt, 1/4 - 20 X 1 1/4", Hex H.,MS | |
| 244-0002-00 | 13 | Washer, Split Lock, 1/4 | |
| 242~0016-00 | 13 | Washer, Flat, 1/4 | |
| 535-0159-00 | 1 | 4 | Playfield Divider Panel, Middle |
| 535-0160-01 | i | 1 | Playfield Divider Panel, Right |
| 535-0160-02 | 1 | 1 | Playfield Divider Panel, Left |
| 820-0056~00 | 1 | 4 | Decal, Playfield Panel, Wide |
| 820-0057-00 | 1 | 2 | Decal, Playfield Panel, Narrow |
| 820-0058-01 | 2 | Decal, Side, Back Box | |
| 820-0058-02 | 2 | Decal,Side, Back Box | |
| 820-0058-03 | 2 | Decal, Side, Back Box | |
| 820-0058-04 | 2 | Decal, Side, Back Box | |
| 535-0155-01 | 1 | 1 | Grate, Right |
| 535-0155-02 | 1 | as | Grate, Left |
| 535-0166-00 | 1 | 1 | Roll Bar (U Channel) |
| 535-0156-00 | 2. | 1 | Energy Divider Panel |
| 234~0013-02 | 2 | 2 | Bolt, #10-24 X 3/4", Button Head,MS |
| 535-0157-00 | 1 | 1 | Cosmo Divider Panel |
| 515-0030-03 | 1 | 1 | ON/OFF Switch Assy |
510-0208-00 BACK BOX ASSY, COSMO (Continued) Part Number Description
ITEM PART NUMBER REV QTY/ASY QTY/GM 231-0013-10 231-0013-05 231-0013-04 242-0022-00 242-0021-00 238-0015-00 239~0010-00 242-0010-00 232-0014-02 660-0012-00 660-0011-00 660-9010-00 535-0189-01 535-0189-02 234-0003-03 242-0023-00 285-0011-60 231-0016-02 231-0007-02
Preliminary : 01-15-91 PREPP
Pw DESCRIPTION Bolt, Button Head,Hex, 5/16-18 X 2 1/4 Bolt, Button Head,Hex, 5/16-18 X 2" Bolt, Button Head,Hex, 5/16-18 X 1 1/2" Washer, flat, 5/16 Washer, Fender, Black, 5/16 X 1 1/4" Nut, Kep, 5/16-18 Well Nut, #10-32 Washer, Flat, #10 , Black Screw, Button Head, Hex, #10-32 X 1", MS Shield, Vertical Shield, Angled Shield, Top Bracket, Shield, Insde Bracket, Shield, Outside Screw, Button Head,Black #8-32 xX 3/4, MS Washer, Flat, #8 , Black Rubber Bumper, Black, t=1/4",#SJ5018 Bolt, But.H, 1/4-20 X 1/2" Bolt, Carriage, #10-24 X 1", MS
510-0210-00 TOP BOX ASSY, COSMO Part Number Description
ITEM PART NUMBER REV QTY/ASY QTY/GM 036-0256-00 036-0257~-00 036-0260-00 036-0261-00 036-0269-00 040-0007-00 366-0032~00 366-0024-00 366-0029-00 366~0030-00 800-0052-00 820-0059-00 231-0013-04 242-0021-00 242-0022-00 238-0015-00 545-0017-00 545-0018-00 232-0002-02 545-0019-00 232-0008-02 242-5011-00 239-0002~00 545-0020-00 545-00321-00 077-5101~00 545-0023-00 232-0007-02 239-0009-00 535-0185-00 510-0206-00 239~0001-00 077-0003-00 165-5000-89 077-0002-00 165-0008-00 232-0003-00 810-0049-00 200-0024-00 205-0003-01 233-0001-03 234-0013-02 242-0010-00 406-0002-00 406-0003~00 406-0004-00
Preliminary : 01-11-91 PWOWRPYPPNN DR APPRPPPP RPP P PB
BP PPRUUDPPPODMROCONEPH ERP H LIST OF MATERIALS
NPRPRPR
PRRPPPRH
NNPPR
PPP DESCRIPTION Harness, Lamp Extension,Top Box Harness, UFO Lamp (8 lamps Harness, Cosmo Spot lamp (5 lamps) Harness, Boss Spot Lamp (3 lamps) Harness, Wing Lamp Clamp, Cable, Nylon, 3/8 Title Board Top Box Access Door, Top Box Light Board, Top Box Overlay, Marquee Decal, Above Cage Bolt, Button Head, 5/16-18 X 1 1/2 Washer, Fender, Black, 5/16 X 1 1/4" Washer, Flat, 5/16 Nut, Kep, Hex, 5/16-18 UFO (A) UFO (B) Screw, PH, #8 X 3/4, SMS UFO (C), Red Dome Insert Screw, PH, #8-32 X 1/2, MS Washer, Plat, #8 Nut, Kep, #8-32 Dome Film, Plastic, Red Socket (Wing Lamp) Lens, Red Screw, Lens, PH, 76-32 X 1/2, MS Nut, Kep, #6-32 Bracket, Character Boss Charcter Boss Nut, Kep, #10-24 Socket, Short, Standup #89 Lamp, #89, 13V Socket, Miniature Bayonet, straight Lamp, #1816, 13V, .33A Screw, PH., #6 X 1/2 SMS Back Board w/artwork (cardboard) Fuse, 2.5A, 250V, Fast Blo Fuse Holder, 1 position Screw, FH, #8 X 11/4", SMS Screw, Button Head #10-24 X 3/4 Washer, Flat, #10 Label, FCC Warning Label, FBI Warning Label, Serial Number
510-0211~00 POWER SUPPLY ASSY, COSMO Part Number Description
LIST OF MATERIALS
ITEM PART NUMBER 036-0264-06 036~-0265-00 036-0266-00 036-0268-00 010~0011-00 040-0003-00 040-0007-00 112~-0054-00 112-0057-00 116-0021-00 120-0001-43 121-0008-00 124-0001-00 125-0016-00 125-0019-01 135-0003-00 150-0006-00 232-0003~00 1 232-0008-07 242-5011-00 239-0002~00 232-0002-01 233-0001-02 034-0001~-00 280-0001-00 535-0010-00 200-0021~-00 200-0017-00 200-0018-00 200-0012-00 200-0020-00 205-0003-05 406-0433-00 406-0434~-00 660-0003-00 232-0004-06 366-0033-00 232-0027-01 REV QTY/ASY QTY/GM BRRPREH PUN PNP RPNUURPEBE PRP RP PRP PPP PPP HPP EPR RU WURPEPEBENHEBPEP
PPR
_ Preliminary : 61-11-91 DESCRIPTION Harness, Power (Power Supply) Harness, Coin Door Lamp Harness, Fuse Harness, Power (On/ Off Sw. Side) Transformer, 24Vac, 12Vac, 9Vac Tywrap, 4" Clamp, Cable, Nylon, 3/8" Bridge Rectifier, MDA 2501 Bridge Rectifier, MDA 3502 Heat Sink Resistor, 2.2Kn, 1/4 W Fixed Power Resistor, 100n, Resistor Mounting Hardware Capacitor, Elec.Can Style 21000,35Vdc Cap., Elec. Can Style, 23000uF,40Vdc Cap. Mounting Hardware MALLORY Filter, Noise Screw, Pan, #6 X 1/2 SMS Screw, #8-32 X 11/4, PH, MS Washer, Flat 78 Nut, Kep, #8-32 Screw, PH, #8 X 5/8, Screw, Flat, #8 X 1" SMS Power Cord, 12 ft Strain Relief Strain Relief Plate Fuse, 3A, Fast Blo Fuse, 6A, Fast Blo Fuse, 6A, Slo Blo (Coin Lamp) Fuse, 8A, Fast Blo (12v) Fuse, 15A, Fast Blo (24V) Fuse Holder, 5 position Fuse Label Label, Caution, Power Supply Fish Paper, 4 X 8" (safety cover) Screw, PH, #10 X 5/8, SMS Power Supply Board (Plywood) Screw, PH, Phil, #8 X 3/8, self tapping 50W
SMS
(8.5V) (line fuse)
§10-0205-00 DRIVE UNIT ASSY, COSMO Part Number Description
LIST OF MATERIALS
ITEM PART NUMBER 036-0248-01 036-0248-11 036-0249-01 036-0248-02 036-0248-12 036-0249-02 036-0248-03 036-0248-13 036-0249-03 036-0248-04 036-0248-14 036-0249-04 036~-0248-05 036-0248-15 036-0249-05 510-0204-00 535-0175-00 535-0176-00 545-0016-00 080-0005-00 535-0177-00 VUNUKHUMOHHHUNOOP PPP RPP PRP PRPRPPRPRPR
121-0007-00 1 305-0002-00 535-0171-00 520-0097~00 1 305-0002-00 530-0033-00 254-0019-00 10 250-0009-00 20 315-0001-00 5 232-0021-03 30 239-0010-00 15 232-0009-06 15 232~0008-02 20 232-0009-02 20 535-0186-00 5 535-0187-00 5 285-6010-00 15 PUP PE ERYUDPENPHUHPEPNE PPP EP BPP EPEPBPEBRPRPRPPPBRPPE
535-0188-00
Preliminary : 01-04-91 REV QTY/ASY QTY/GM DESCRIPTION Harness, Sensor, Front Harness, Sensor, Back Harness, Sensor, Center Harness, Sensor, Front Harness, Sensor, Back Harness, Sensor, Center Harness, Sensor, Front Harness, Sensor, Back Harness, Sensor, Center Harness, Sensor, Front Harness, Sensor, Back Harness, Sensor, Center Harness, Sensor, Front Harness, Sensor, Back Harness, Sensor, Center Character Assy w/photo pcb Character Carrier Energy Carrier w/ sensor pcb Energy Box Motor, 5.5VDC, 1.25A Motor Bracket Ceramic Resistor, 16, 30W Pulley, Big Rail Sensor Pcb Pulley(B), w/bearing, Small, SAVA MP-614 Shaft, Small Pulley Spacer, Bronze, ID=, OD= E-Ring Cable, 148", 1/32 Screw, Pan, #4-40 X 1/4", MS Well Nut, #10-32 WACHTEL 7 G-1032 Screw, Phil, #10-32 X 1", MS Screw, Phil, #8-32 X 1/2, MS Screw, Phil, #10-32 X 1/2, MS Front Stopper Bracket w/hook Rear Stopper Bracket Cushion, t=1/2" Bracket, Small Pulley
515-0077-00 SEAT UNIT ASSY, COSMO Part Number Description
LIST OF MATERIALS
ITEM PART NUMBER REV QTY/ASY QTY/GM DESCRIPTION
| ol | 231-0001-20 | 8 | Bolt, Hex Head, 1/4-20 X 1 3/4", MS |
| 02 | 231-0012-13 | Bolt, Hex, 3/8-16 X 2 3/4" | |
| 03 | 234-0003-02 | 1 | Screw, Button Head, #8-32 X 1/2 MS |
| 04 | 238-0009-00 | Nut, Hex, 3/8 | |
| 05 | 242-0017-00 | Washer, Flat, Fender, ID=9/32, OD=1" | |
| 06 | 244-0008-00 | Washer, Split Lock, 3/8 | |
| 07 | 366-0021~00 | Spacer, Particle Board | |
| 08 | 535-0161-00 | Seat Frame | |
| 09 | 535-0164-00 | Seat, Bottom | |
| 10 | 535-0170-00 | Guide, Hat, Seat Frame | |
| ll | 545-0021-00 | Seat | |
| 12 | 400-0003-00 | Foot Leveling, #3/8 - 16 X 1 1/2 |
NPRPRPPENONAN NEPNPY
Released : 01-11-91
§15-0078-00 XENON LAMP ASSY, COSMO Part Number Description
LIST OF MATERIALS
ITEM PART NUMBER REV QTY/ASY QTY/GM DESCRIPTION
| o1 | 160-0006-00 | 1 | 2 | Xenon Tube w/harness |
| 02 | 535-0163-00 | 1 | 2 | Bracket w/Xenon Clip |
| 03 | 535-0179-00 | 1 | 2 | Grill, Xenon Tube |
end
Released : 01-04-91
515-0057-00 SERVICE PANEL ASSY, COSMO Part Number Description
LIST OF MATERIALS
ITEM PART NUMBER REV QTY/ASY QTY/GM DESCRIPTION
| 01 | 036-0211-01 | Harness, Service Panel |
| 02 | 090-0002-00 | Coin Counter |
| 03 | 123-0008-11 | Potentiometer, 100, 2W |
| 04 | 180-0024-00 | Pushbtn w/usw, Black |
| 05 | 180-0024-02 | Pushbtn w/usw, Red |
| 06 | 232-0018-01 | Screw, PH, Phil, #5 X 1/2", SMS |
| 07 | 406-0096-00 | Label, Volume |
| 08 | 406-0287-00 | Label, Test |
| 09 | 535-0135-00 | Bracket, Service Panel |
PRRPNPRPREREH PRPNPPPEPB
Released : 12-17-90
515-0079-00 DISPLAY (SPEAKER) PANEL ASSY, COSMO Part Number Description
LIST OF MATERIALS
ITEM __PART_NUMBER__REV_OQTY/ASY QTY/GM DESCRIPTION
| o1 031-0008-00 | 1 | 2 | Speaker, 4.68 X 4.68, 8N,6W | |
| 02 | 036-0253-00 | 1 | 1 | Harness, Speaker |
| 03 232-0003-00 | 8 | Screw, #6 X 1/2, Ph, SMS | ||
| 04 232-0003-06 | 8 | Screw, Ph, #6 X 5/8 SMS | ||
| 05 232-0007-00 | 6 | Screw, #6-32 X 1/4, PH, MS | ||
| 06 239-0009-00 | 6 | Nut, Kep, #6-32 | ||
| 07 | 366-0031-00 | 1 | 1 | Display (Speaker) Panel, Wood |
| 08 510-0199-00 | 1 | 1 | Pcb, Display | |
| 09 | 535-0131-00 | 6 | - Z Bracket | |
| 10 535-0178-00 | 2 | Speaker Grill | ||
| 11 830-0053-00 | 1 | 1 | Score Panel Plex | |
| 12 | 233-0001-05 | Screw, FH, #8 X 5/8, SMS |
Released : 01-15-91
515-0081-00 WIN LAMP PANEL ASSY, COSMO Part Number Description
LIST OF MATERIALS
ITEM__PART NUMBER REV OTY/ASY OTE GM DESCRIPTION
| ol | 036-0252-00 | Harness, Win Lamp |
| 02 | 040-0001-00 | Clamp, Cable, Stickdown |
| 03 | 077-5100-00 | Socket, Laydown |
| 04 | 165-5000-89 | Lamp, 13V, #89 |
| 05 | 232-0007-02 | Screw, PH, #6-32 X 1/2", MS |
| 06 | 232-0007-09 | Screw, PH, #6-32 X 1 3/4, MS |
| 07 | 239-0009-00 | Nut, #6-32 |
| 08 | 406-0430-00 | Label, Win Lamp |
| 09 | 535-0168-00 | Panel, Win |
| 10 | 545-0022-00 | Lens, Win Lamp |
PEP PUNY N OPP
PPP
Released : 12-17-90