CATHODE RAY TOMES

Race On

Race On! (World, RO2 Ver. A) (Namco, 1998) · Manual · 87 pages · 38 sections · original scan

Page 1

€S000SG06 “ON Hed “ATaSIOSYd GAMOT1IOS SHV TVANYW SIHL NI LNO LHS STIVLEC SHL LVHL SALLVYSdWI SI LI ONY ‘SSWIL TV LV ALAsSVS YAWNOLSND NIVLNIVW OL HOLVHAdO SHL SO ALIMISISNOdSSY SHL SI L] enue ssoyes9dO

Page 2

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 3

PORTABLE APPLIANCE TESTING

Please Note:

During testing of the machine with a portable appliance tester the insulation test will show a failure due to the fitting of two VDRs between Live/Earth and Neutral/Earth.

These components have been fitted to safeguard against high voltage surges that may occur on the mains supply to the machine and to comply with the EMC regulations.

To conduct an insulation test on this machine, the VDRs must be isolated from the circuit first.

Ensure that the VDRs are reconnected after the insulation test has been completed and before the machine is placed back into service.

The VDRs used have been specified and tested as safety critical components.

Page 4

GB) No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of phonographic recording, nor may it be stored in a retrieval system, transmitted or otherwise copied for private or public use, without permission from NAMCO EUROPE LIMITED.

While the information contained in this manual is given in good faith and was accurate at the time of printing. NAMCO EUROPE LIMITED reserve the right to make changes and alterations without notice.

This machine has been manufactured in accordance with European Community Directives, and has been tested and complies with the Directives 89/336/EEC and 72/23/EEC by the application of EN55014-1, EN55014-2 and EN60335-1 standards (see front of manual) and as such bears the C€ marking. Any changes or modifications to this machine must be in accordance with the European Directives. Any unauthorised changes to this product, may contravene such Directives.

Under some conditions of extreme external interference, e.g. radio transmissions, electrostatic discharge or mains borne transients, some degradation of performance may occur. However the machine will recover normal performance once the source of the interference has ceased or been removed. Following abnormally high surges on the mains supply, the video monitor may need to be manualy reset by turning the machine OFF and back ON.

Note:- If the game processor resets due to an interuption or reduction of the mains voltage any credits established may be lost.

This game is not a machine as defined by the Machinery Directive 89/392/EEC

SAFETY WARNING

In order to use this machine safely, be sure to read this Operators Manual carefully before installation, adjustment or use of this machine.

Whenever the owner of this machine entrusts dis-assembly, installation, adjustment or routine maintenance to another person, the owner should ensure that that person read the appropriate precautions and relevant sections of this manual before starting work.

In order that no accidents occur when the machine is in operation, strictly follow the notes on safety as described below.

This manual along with the Installation Manual (where applicable) form an integral part of the equipment and must be available to the operating and service personnel at all times.

This machine is for indoor use only and should only be used for the purpose intended.

Namco Ltd. bears no responsibility for accidents, injury or damage resulting from unauthorized changes to, or improper use of this machine.

SAFETY NOTES

The following safety notes are used throughout this manual. Familiarize yourself with each of these notes and its meaning before installing, servicing or making adjustments to this machine.

WARNING /\ Warning denotes a hazard that could result in injury or death. Do not proceed beyond a
warning note until the indicated conditions are fully understood and met.
CAUTION (1) Caution denotes a hazard that could result in damage to the machine. Do not proceed beyond a
warning note until the indicated conditions are fully understood and met.

GENERAL SAFETY CONSIDERATIONS

Only operate this machine after checking that it has been installed correctly and in accordance with the manual.

Parts of this machine move during game play, so there are places where the distance between the stationary section and moveable section changes. There are warning notices to keep hands and feet clear of moving parts, however if the operator feels that a person is in any danger, he should warn that person accordingly.

The warning notices must always be kept in good condition and replaced if worn, so that customers can read them clearly.

If there is an error or problem with the machine, operation must be stopped immediately and the problem rectified before any further use.

Installation, service, adjustment or routine maintenance should be carried out by suitably qualified persons only.

For continued protection against fire hazard, replace fuses with the same type and rating. The use of other fuses or material is prohibited.

The power supply inside the monitor will remain hot and have areas of high voltage even though the machine has been turned OFF, and there is the possibility of burns or electric shock. Be careful not to touch these areas.

To prevent possible electric shock due to failure, this machine MUST be fitted with a securely connected EARTHED plug.

If at any time the mains supply lead becomes damaged, it must be replaced immediately.

Do not turn the power switch ON until the machine has been installed correctly. OPP BBP BBB BP BE

Before connecting the machine to the mains supply, ensure that the machine is set for the correct voltage and that the correct fuses are fitted

Page 5

Va

Va NOTES ON INSTALLATION

A NEVER turn the power to the machine ON until installation has

A In order to prevent possible electric shocks, be sure that the -

A

0) been completed.

machine is connected to the mains with a securely connected earthed plug. = . :

So that customers are not injured by the movement of the machine, | ensure that there is as least 500mm separation between other = = machines or walls. “= |

In order to avoid damage to the machine due to mis-operation, ensure that the voltage of the mains supply is 230volts AC.

Note: If the location of this machine has a polished floor, it is recommended that rubber pads are fitted under the level adjusters to prevent the machine sliding on the floor.
Note: In order to gain access to the Power Supply and CPU assemblies, make ‘sure that the rear of the machine is separated from a wall or other machine by at least 500mm.

> bP FP Bb MOVING THE MACHINE

This machine is fitted with castors to make it easier to move. Take care when moving the machine on an inclined surface.

The Header Assembly has a forward centre of gravity, so it is important that at least two people are used to fit or remove the Header Assembly.

The fitting position of the Header Assembly is high, and it is important that a means of reaching the height safely,without stretching, is available. (e.g. Steps, Step Stool etc.)

The overall height of the machine, with the Header Assembly fitted, is 1990mm. Take care of any overhead obstructions. (e.g. Light Fittings, Electric Cables etc.)

When moving the game, ensure that the game is dis-assembled into 3 parts: Monitor Assy, Ride Assy and Header Assy.

>BeP BP B&B BP BP BB REMOVING AND REPLACING PARTS Adjustments or maintenance on this machine should be carried out by suitably qualified personnel only.

Do not make any alteration to this machine without prior approval. Doing so could cause unforeseeable

danger.

Only parts specified by Namco Europe Ltd should be used when replacing or repairing parts. (Including screws).

Ensure that the power to the machine is turned OFF before commencing any maintenance work. (Trouble shooting, repairs etc.)

If performing work not described in this manual, be sure to contact your distributor for instructions, as no responsibility will be accepted for damage or injury.

Parts of the Power Supply and Monitor remain hot and carry high voltage even after switching OFF and could cause burns or electric shock. Take care not to touch these parts accidentally.

Make sure that the machine is switched OFF before connecting or disconnecting any plugs or connectors.

When removing the mains connector from the machine, or the mains plug from the wall outlet, always grasp the plug and not the cable. ~\

Page 6

Dieses Dokument darf in keiner Weise vervielfailtigt werden. Jegliche Tonautnahmen sowie die Speicherung auf Datentrager (Suchsysteme), die Weitergabe oder sonstiges Kopieren fur den gewerblichen und privaten Gebrauch sind untersagt und bediirfen der vorherigen Genehmigung durch NAMCO EUROPE LIMITED.

Die informationen in diesem Handbuch entsprechen den Tatsachen bei Drucklegung. NAMCO EUROPE LIMITED behalt sich jedoch das Recht zu Anderungen ohne vorherige Bekanntgabe vor.

Dieses Gert tragt das CE-Zeichen und wurde gema8 den EU-Richtlinien produziert. Es erfillt die Richtlinien 89/336/EEC und 72/23/EEC und Standards EN 55014, EN55104 und EN60335-1 (s. Deckbiatt des Handbuches). Alle Veranderungen an diesem Gert missen in Ubereinstimmung mit den EU-Richtlinien erfolgen. Nicht genehmigte Veranderungen an diesem Gerat verstoBen gegen diese Richtlinien.

Extreme auBere Stérungen, wie z.B. durch Radiobetrieb, elektrostatische Entladung oder zeitweilige Netzschwankungen kénnen zu einer Leistungsminderung fihren. Sobald diese Faktoren jedoch ausgeschaltet oder beseitigt wurden, erreicht das Gert seine normale Leistung.

Achtung! Falls der Spielprozessor auf Grund von Netzunterbrechungen oder Abnahme der Netzspannung aussetzt, kann es zum Verlust von Spielkrediten kommen.

Dieses Gert fallt nicht unter die Maschinen-Richtlinie 89/392/EEC

SICHERHEITSHINWEISE

Um einen ordnungsgemasen Bettieb dieses Gerates zu gewahrleisten, muB vor Aufstellung, Inbetriepnahme und Gebrauch das Handbuch sorgfaltig gelesen werden Sobald der Besitzer dieses Gerates die Demontage, Aufstellung, Inbetriebnahme oder den Service einer anderen Person ibertragt, muB er sicherstellen, daB diese Person vor Arbeitsbeginn die nétigen Sicherheitshinweise und die dazugehdrigen Kapitel des Handbuches liest und versteht. Um jegliche Unfalle wahrend des Betriebes zu vermeiden, mussen obige Hinweise strikt befolgt werden. Dieses Handbuch sowie das spezielle Gerate-Handbuch (wenn vorhanden) gehéren zum Gerat und mussen dem Betreiber und Wartungspersonal stets zuganglich sein. Dieses Gerat ist ausschlieBlich flir den gewerblichen Gebrauch in geschlossenen Réumen bestimmt und darf nur dort betrieben werden. NAMCO LTD. dibernimmt keinerlei Haftung far Unfalle, Verletzungen oder Beschadigungen, die auf nicht genehmigte Verdinderungen oder unsachgemaBen Betrieb des Gerates zuriickzufihren sind.

SICHERHEITSHINWEISE

Folgende Sicherheitsbegriffe werden im gesamten Handbuch benutzt. Machen Sie sich daher bitte vor Inbetriebnahme, Wartung und Durchfiihrung von Einstellungen am Gerat mit diesen Warnhinweisen vertraut.

WARNUNG /\ WARNUNG bezeichnet eine Gefahrenquelle fir Leib und Leben. Erscheint dieser Warnhinweis, darf erst weitergearbeitet werden, wenn die entsprechenden Erklarungen vollstandig verstanden und befolgt wurden

VORSICHT (0) VORSICHT bezeichnet eine Gefahrenquelle fiir die Beschadigung des Gerates. Erscheint dieser Warhinweis, darf erst weitergearbeitet werden, wenn die entsprechenden Erklarungen vollstandig verstanden und befolgt wurden.

ALLGEMEINE SICHERHEITSHINWEISE

Das Gerat darf nur betrieben werden, nachdem es vorschriftsmaBig und in Ubereinstimmung mit dem Handbuch aufgestellt wurde.

Das Gerat bewegt sich wahrend des Spielbetriebes, somit verandert sich der Abstand zwischen feststehenden und beweglichen Teilen. Warnschilder verweisen darauf, fur Hande und FiBe einen gebihrenden Sicherheitsabstand einzuhalten. Sobald eine Person in Gefahr ist, muB der Betreiber sie warnen.

Die Warnschilder miissen in gutem Zustand sein und ersetzt werden, wenn sie nicht mehr gut lesbar sind.

Bei Auftreten eines Fehlers oder Problems muB das Gerat sofort abgeschaltet werden und darf erst nach fachgerechter Behebung des Fehlers wieder in Betrieb genommen werden.

Aufstellung, Service, Einstellungen und Wartung dirfen nur von dafiir qualifiziertem Fachpersonal durchgefiihrt werden

Zur Vermeidung von Feuer, defekte Sicherungen nur durch vorgeschriebene Sicherungen ersetzen. Die Verwendung von andersartigen Sicherungen oder unterschiedlichem Material ist untersagt.

Das Netzteil im Monitor bleibt nach Ausschalten des Gerates noch hei8 und fiihrt weiterhin Hochspannung. Daher besteht die Gefahr von Verbrennungen und Elektroschlagen. Diese Bereiche dirfen nicht bertihrt werden.

Zur Vermeidung von Elektroschlagen muB dieses Gerat mit einem ordnungsgemaé geerdeten Netzstecker versehen sein.

Bei Beschadigungen des Netzteiles muB dieses umgehend ersetzt werden

GerAt erst nach abgeschlossener Aufstellung einschalten.

Vor Einstecken des Netzsteckers bitte sicherstellen, daB Netzspannung und Gerdtespannung dbereinstimmen, und die vorgeschriebenen Sicherungen verwendet wurden. OP PBBPB BP BPE BB

Page 7

FO

Oo FP EB HINWEISE ZUR AUFSTELLUNG

NIEMALS das GerAt einschalten bevor die Aufstellung véllig —ssereres | Saneree——— abgeschlossen ist.

Zur Vermeidung von Elektroschlagen muB das Gerat mit einem eam ordnungsgemaB geerdetem Netzstecker an die Stromversorgung angeschlossen werden

Um zu vermeiden, daB Kunden durch die Geratebewegungen > | verletzt werden, muB ein Sicherheitsabstand zu anderen Geraten und Wanden von mindestens 50cm eingehalten werden.

Zur Vermeidung von Beschadigungen durch Fehibetrieb am Gerat sicherstellen, daB die Netzspannung 230 Volt betragt.

Hinweis: Ist das Gerat fiir einen Aufstellplatz mit glattem FuBboden bestimmt, missen die Standbeine mit Gummiplattchen unterlegt werden, damit das GerAt fest steht und nicht auf dem Boden hin- und herrutscht.

Hinweis: Zu Reparaturzwecken am Netzteil und den CPU-Komponenten muB die Rickseite des Gerates mindestens 50cm von anderen Geraten und der Wand entfernt sein. XN

be BPE &- Zum leichteren Transport ist das Gerat mit Rollen ausgeriistet. Daher besondere Vorsicht auf abschissigem Boden

Der Schwerpunkt des Aufsatzes liegt sehr weit vorn. Daher werden flr den Ab- und Aufbau des Aufsatzes mindestens 2 Personen bendtigt.

Der Aufsatz wird in groBer Héhe montiert. Daher muB aus Sicherheitsgriinden eine Steighilfe, wie z. B. eine Leiter, ein Tritt oder 4hnliches, verwendet werden.

Die Gesamthohe de Gerates betragt 1.90m. Daher Vorsicht bei tiefer hangenden Beleuchtungskorpern.

Fir den Transport oder bei einem Platzwechsel Ge! Fahreinheit in drei Teile zerlegen: Kopfteil, Vorderteil, und

PBPBBPBBE PB B&B AUS- UND EINBAU VON KOMPONENTEN UND TEILEN

Aufstellung, Service, Einstellung und Wartung dirfen nur von dafir qualifiziertem Fachpersonal durchgefiihrt werden.

Es diirfen keierlei Verainderungen ohne vorherige Genehmigung am Gerat vorgenommen werden. Zuwiderhandlungen stellen eine Gefahrenquelle dar.

Fir die Repartur dirfen nur Originalersatzteile (incl. Schrauben) von NAMCO EUROPE LTD. verwendet werden.

Vor Beginn aller Wartungsarbeiten (Fehlersuche, Reparaturen etc.) muB der Netzstecker gezogen werden

Bei Arbeiten, die nicht in diesem Handbuch beschrieben werden, muB vorher der Handler zu Rate gezogen werden, da sonst keinerlei Haftung bei Beschadigungen und Verletzungen Gbernommen wird.

Teile des Netzteiles und Bilschirmes bleiben nach Abschalten noch hei® und fihren Hochspannung. Dies kann zu Verbrennungen oder einem Elektroschlag fihren. Diese Teile dirfen nich beriihrt werden.

Vor der Montage oder dem Entfernen von Steckverbindungen und Steckern muB das Gerat ausgeschaltet werden.

Bei Ziehen des Geratesteckers oder des Netzsteckers aus der Wandsteckdose stets den Stecker greifen und nicht das Kabel S

Page 8

Denne udgivelse ma ikke reproduceres af nogen som helst mekanisk, fotografisk eller elektrornisk proces eller i form af indspilning, den ma heller ikke lagres i et eftersogningssystem transmitteres eller kopieres til nogen form for offentlig benyttelse uden tilladelse fra Namco Europe Limited.

Da informationerne i denne manual er givet med god tro og var korrekt pa udskivningstidspunktet, forbeholder Namco Europe Limited sig retten til, at foretage zendringer og forandringer uden varsel.

Denne maskine er frernstillet i overensstemmelse med Det Europziske feellesskabs direktiver og er blevet testet og fuldendt med direktiverne 89/336/EEC og 72/23/EEC standarder (se manualens forside) og som sadan beerer CE meerket. Enhver form for zendring eller modiflkation af denne maskine skal vere i overensstemmelse med Det Europeiske feellesskabs direktiver.

| tilfeelde af forbigaende ekstreme eksterne forstyrrelser, sA som radio udsendelser, elektronisk afgivelse eller forstyrrelser pa ledningsnettet, kan nedbrydning forekomme. Maskinen vil dog kore normalt sa snart forstyrrelsen ophorer eller bliver fjernet.

Bemeerk:- Hvis spilleprocessoren resetter p.g.a. en forstyrrelse eller reduktion af hovedstrommen kan de etabledrede kreditter gA tabt.

Dette spil er ikke en maskine defineret af maskin direktivet 89/392/EEC -

SIKKERHEDS ADVARSEL

For at betjene denne maskine sikkert, lags da denne brugemanual grundigt for installation, justering eller brug af maskinen. Nar som helst ejeren af denne maskine overlader demontering, installation, justeringer eller daglig vedligehold til en anden person, skal ejeren sikre sig at denne person leser de sikkerhedsregler og relevante punkter i denne manual for arbejdet begynder. For at undga ulykker nor maskinen er i gang, folg noje de sikkerhedsregler der er beskrevet herunder. Denne manual sammen med installations manualen er en uloselig del af udstyret og skal altid veere til raidighed for det arbejdende og servicerende personale. Denne rnaskine er kun til indendors brug og bor kun bruges til det beregnede formal. Namco Ltd. beerer intet ansvar for ulykker eller skader som er et resultat af uautoriserede zendringer eller fejlagtig brug af denne rnaskine.

SIKKERHEDSREGLER

De folgende sikkerhedsregler er brugt helt igennem denne manual. Gor dig bekendt med hver enkelt af dem og meningen heraf for installering, servicering eller justering af denne maskine.

ADVARSEL /\ Advarsel betegner en episode der kan resultere i skader eller dod. Begiv dig ikke forbi et advarselsskilt for de indikerede betingelser er fuldstaendig forstaet FORSIGTIG (7) _ Forslgtig betegner en episode der kan resultere i odelaggelse af maskinen. Begiv dig ikke forbi et advarselsskit for de indikerede betingeser er fuldstzendig forstaet.

GENERELLE SIKKERHEDSOVERVEJELSER

Betjen kun maskinen efter at have tjekket, at den er korrekt installeret og er i overensstemmelse med manualen.

Dele af denne maskine er i beveegelse nar den korer s& der er steder hvor afstanden mellem den stationzere og den bevaegende sektion zendrer sig. Der er advarselsskilt om, at holde hzender og fodder veek fra de beveegelige dele, dog skal lederen straks advare en person han foler der er i fare.

Advarselsskiltene skal altid veere i god stand og erstattes hvis de er slidt, sa kunden tydeligt kan lease dem

Hvis der er en fejl eller et problem med maskinen skal betjening straks stoppes, og problemet afhjzlpes for yderligere brug.

Installations service, justeringer eller daglig vedligehold bor kun udfores af en kvalificeret person.

For fortsat beskyttelse mod brandfare, sikres at hoved sikringerne kun erstattes med samme type kapacitet. Brug af anden kapacitet eller materiale er forbudt.

Stromforsyningen inde 1 monitoren vil forblive varin og have omrader med hoj spzending selvom maskinen har veeret slukket og der er fare for brandskader eller elektrisk stod. Pas pa med at rore disse omrader

For at undga elektrisk stod p.g.a. en fejl skal denne maskine veere forbundet med et sikkert jordstik.

Hvis hoved ledningerne pa noget tidspunkt bliver beskadiget skal de strakt erstattes

Teend ikke for strommen for maskinen er korrekt installeret.

For tilslutning af maskinen til hovedstrommen sikres, at maskinen er indstillet til den rette spending. OPBeB BBPBBP Be B B&

Page 9

Ne OP BBE PUNKTER OM INSTALLATION

Teend aldrig for strommen til maskinen for installering er fuldfort. i a

For at undga mulige elektriske stod sikres, at maskinen er forbundet til hovedstrommen med sikkert monterede jordstik. tae ated For at kunder ikke kommer til skade ved spillets bevegelser sikres, at der er mindst 50cm afstand til andre maskiner og veegge. aa

For at undga skader pA maskinen p.g.a. fejlbetjening sikres, at speendingen : pa hovedstrommen er 230 volt AC. | ==

BEMERK : Hvis denne maskine placeres pa et poleret gulv, anbefales det at ligge gummimatter under justeringsfodderne for at undga at maskinen glider pa gulvet.

BEM/ERK : For at f adgang til stromforsyningen og CPU justeringer sikres, at bagsiden af hoved kabinettet star adskilt fra andre maskiner eller a veeggen med mindst 50cm.

Va

> Maskinen er smurt med olie for at gore den lettere bevaegelig. Pas pa nar maskinen flyttes pa en skra overflade.

Hoved sektionens forreste center er meget tung, det er derfor vigtigt, at mindst 2 personer benyttes til at montere el. flytte hoved sektionen.

Monterins hojden af hoved sektionen er meget hgj og det er vigtigt, at have hjzelpemidler til at na sikkert uden at skulle straekke sig. (fek.s. trapper, trappestole el. lign.).

Den fulde hgjde af hoved sektionen er 1.90m. Pas pa ovre forhindringer f.eks. lys inventar.

Nar spillet skal flyttes eller bares skal det sikres at den er demonteret i 3 dele: - Hoved sektion - Front sektion - Kore sektion ~

/

bPRP Bb BP BP PBBE AT FJERNE OG UDSKIFTE SEKTIONER OG DELE.

Justeringer eller vedligehold af denne maskine bor kun udfores af kvalificeret personale.

Skift ikke noget pa maskinen uden godkendelse, det kan fore til uforudset fare.

Der bor kun bruges dele specificeret af Namco Europe Limited nar der skiftes eller repareres dele (inklusiv skruer).

Sorg for, at strommen til maskinen er slukket for der foretages nogen form for arbejde (fejlfinding, reparation etc.)

Hvis der foretages arbejde der ikke er beskrevet i denne manual, kontakt da din leverandor for at fa kyndig vejledning, da intet ansvar vil blive accepteret ved skader.

Dele af stromforsyningen og monitoren forbliver varme eller baerer hoj speending selv efter maskinen er slukket, det kan fore til forbraendinger eller elektriske stod. Pas pa ikke at rore disse dele ved et uheld.

Leeg meerke til at maskinen er slukket for samlinger eller stik tages ud eller szettes i.

Nar hovedsamlingen fjernes fra maskinen eller hovedstikket fjernes fra vaeggen, tag da altid ved stikket, ikke ledningen. ~

Page 10

© No se permite la reproduccién total ni parcial de esta publicacién por ningun medio mecanico, fotografico 0 electronico, grabaciones fonograficas, ni su almacenamiento informatico, su transmision o su copia, ya sea para uso pUblico o privado, sin permiso de NAMCO EUROPE LIMITED.

Si bien la informacion contenida en este manual se da de buena fe y es correcta en el momento de su impresion, NAMCO EUROPE LIMITED se reserva el derecho de hacer cambios y alteraciones sin previo aviso.

Esta maquina ha sido fabricada segun las directrices de la Comunidad Europea, ha sido probada, y se ajusta a las directrices 89/336/EEC y 72/23/EEC, mediante la aplicacion de los estandares EN65014, EN65104 y EN60335-1 (véase cubierta del manual) y por ende lleva el sello de la C.E. Cualquier cambio o modificacion que se haga a esta maquina ha de ajustarse a las directrices de la Comunidad Europea. Cualquier cambio no autorizado hecho al producto pudiera contravenir estas directrices.

Bajo ciertas condiciones de extrema interferencia externa, p. ej. transmisiones de radio, descargas electrostaticas u oscilaciones de la red eléctrica puede tener lugar un descenso del rendimiento. No obstante, la maquina recuperara su rendimiento normal una vez que la fuente de interferencias sea retirada o cese de producirlas. Nota: Si el procesador de juegos se reinicializa a causa de caidas o interrupciones en la alimentacion eléctrica, se perderan todos los créditos.

Este juego no se ajusta a la definicion de maquina de la Normativa de Maquinaria 89/392/EEC.

AVISOS DE SEGURIDAD.

Para utilizar esta maquina con seguridad, lea cuidadosamente este Manual de Operador antes de proceder a la instalacion, ajuste 0 uso de esta maquina. Cada vez que el propietario de esta maquina confie a terceros su desmontaje, instalacion, ajuste 0 mantenimiento tutinario debera asegurarse de que tales personas lean las precauciones adecuadas y las secciones relevantes de este manual antes de comenzar su trabajo Para que no ocurra accidente alguno mientras la maquina se encuentre en funcionamiento, siga estrictamente las notas de seguridad tal como mas adelante se describen. Este manual, junto con el Manual de Instalacion (cuando proceda), forma parte integral del equipo y debe estar a disposicién del personal de mantenimiento y operacion en todo momento. Esta maquina es Unicamente para ser usada en interiores, y solo debe usarse para aquello para lo que ha sido creada. Namco Ltd. queda exenta de cualquier responsabilidad por accidentes, heridas 0 dafios causados por cambios no autorizados 0 uso indebido de esta maquina.

NOTAS DE SEGURIDAD.

En este manual se usan las notas siguientes. Familiaricese con cada una de ellas y su significado antes de instalar, revisar, o hacer ajustes en esta maquina.

AVISO. /\ Aviso sefiala un riesgo que puede ocasionar lesiones 0 la muerte. Tras ver esta nota, no continue hasta entender completamente y cumplir las condiciones exigidas. PRECAUCION. (1) Precaucién sefiala un riesgo que puede ocasionar dafios a la maquina. Tras ver esta nota, no continue hasta entender completamente y cumplir las condiciones exigidas.

CONSIDERACIONES GENERALES DE SEGURIDAD.

Opere sélo con esta maquina tras comprobar que ha sido instalada correctamente y de acuerdo con este manual. >be Algunas partes de esta maquina se mueven durante el juego; por tanto, hay lugares en que la distancia entre las secciones moviles y estaticas cambia. Existen notas de aviso indicando que se mantengan manos y pies alejados de las partes moviles. No obstante, si el operador cree que cualquier persona se encuentra en peligro, debe advertir de ello a dicha persona.

Las notas de aviso deben mantenerse siempre en buen estado y reemplazarse si estuvieran desgastadas para que los usuarios puedan leerlas con claridad.

Si hubiera algun error o problema con la maquina, debe interrumpirse su operacion inmediatamente, y subsanar el problema antes de volver a usarla.

Las revisiones de instalacién, los ajustes, y el mantenimiento rutinario deberan llevarse a cabo s6lo por personal cualificado.

Para asegurar una continua protecci6n contra riesgo de incendios, asegurese de que los fusibles eléctricos sean reemplazados solamente por otros del mismo tipo y especificaciones. El uso de otros fusibles o material esta prohibido.

La fuente de alimentacion del monitor se mantiene caliente, y tiene zonas de alto voltaje incluso cuando la maquina ha sido desconectada, existiendo el riesgo de quemaduras y descargas eléctricas. Tenga cuidado de no tocar estas zonas. Para evitar posibles descargas eléctricas por cortes, esta maquina debe estar provista de un enchufe debidamente conectado, con TOMA DE TIERRA.

Si en cualquier momento el cable de alimentacin se dafiara, debera ser reemplazado inmediatamente.

No encienda el interruptor de la maquina hasta que ésta haya sido correctamente instalada.

Antes de enchufar la maquina a la red eléctrica, asegurese de que la maquina esta preparada para el voltaje correcto, y de que se usan los fusibles adecuados. OPP EP BP PB BEB

Page 11

~

Oo FP BP -

Notas :

Notas : NOTAS DE INSTALACION.

JAMAS ENCIENDA la maquina antes de haber completado la aaa instalacion.

Para evitar posibles descargas eléctricas, asegurese de que la ] = maquina esta conectada a la red con un enchufe provisto de toma de tierra.

Para que los usuarios no sufran lesiones debido al movimiento del juego, asegurese de que hay al menos 500 mm de separacion entre :

éste y otras maquinas o las paredes. :

Para evitar dafios a la maquina causados por operaci6n incorrecta, aseguirese de que el voltaje de la red es de 230 voltios, corriente alterna.

Si el lugar donde se instalara la maquina tiene un piso pulido, se recomienda colocar tacos de goma bajo los ajustadores de nivel para evitar que la maquina se deslice por el suelo.

Para acceder a las unidades de Fuente de Alimentacion y CPU, asegurese de que la parte trasera del mueble principal esta separada de muros u otras maquinas al menos 500 mm.

El juego tiene ruedecitas para hacer mas facil su traslado. Tenga cuidado al mover la maquina en una superficie inclinada.

La Unidad de Igualaci6n tiene el centro de gravedad desplazado hacia adelante. Es importante que su montaje y desmontaje se haga por al menos dos personas.

La posici6n de la Unidad de Igualacion es bastante alta, y es importante que haya un medio de alcanzar su altura con seguridad, sin estirarse (p. ej. una escalera, un taburete, etc.)

La altura total de la Unidad principal es de 1.90mm. Tenga cuidado de que no haya obstaculos p. ej. luces.

Cuando traslade o mueva el juego, asegurese de que éste haya sido desmontado en 3 partes: Unidad de Igualacién, Unidad Frontal, y Unidad de Juego. S/

> P PBB BP Be B&B RETIRAR Y REEMPLAZAR PARTES Y UNIDADES.

Las revisiones de instalacién, los ajustes, y el mantenimiento rutinario deberan llevarse a cabo solo por personal cualificado.

No realice alteraciones en esta maquina sin aprobacién previa. De hacerlo asi, pueden causar peligros imprevisibles.

Solo deben usarse las partes especificadas por Namco Europe Ltd. para reparaciones o reemplazos (incluidos los tornillos).

Asegirese de que la maquina esta desconectada antes de comenzar cualquier trabajo de mantenimiento (reparaciones, resolucion de problemas, etc.)

Al realizar trabajos no descritos en este manual, pongase en contacto con su distribuidor para recibir instrucciones. Se declina cualquier responsabilidad por dajios o lesiones.

Hay partes de la fuente de alimentacion y del monitor que se mantienen calientes o almacenan alto voltaje incluso tras desconectar la maquina, y pueden producir quemaduras o descargas eléctricas. Tenga cuidado de no tocar accidentalmente estas partes.

Asegurese de que la maquina esta apagada antes de conectar o desconectar cualquier enchufe o conector.

Al retirar el conector principal de la maquina, o la clavija de alimentacion del enchufe de la red, agarre siempre la clavija y no el cable. ~

y,

Page 12

©) Aucun élément de cette publication ne sera reproduit, ni par procédé mécanique, photographique ou électronique, ni par un moyen d'enregistement phonographique. Ces informations ne seront ni stockées grace un procédé de récupération, ni transmises ou autrement copiées pour un usage publique ou privé, sans l'autorisation de NAMCO EUROPE LIMITED.

Malgré le fait que les informations contenues dans ce manuel soient données de bonne foi et étaient actualisées au moment de leur impression, NAMCO EUROPE LIMITED se réserve le droit de procéder & des changements ou a des modifications sans avis préliminaire.

Ce jeu a été fabriqué en respect des normes de la Communauté Européenne, aprés avoir été testé il repond aux normes 89/336/EEC et 72/23/EEC, en application des standards EN55014, EN55104 et EN60335-1 (voir la couverture du manuel), et comme tel il comporte l'autocollant de conformité avec les normes de la Communauté Européenne. Tout changement non’autorisé sur ce produit pourrait contrevenir & ces normes.

Sous certaines conditions extrémes diinterlérence exteme, par example des transmissions radio, des décharges électrostatiques ou bien de interférences passagéres sur le réseau, certaines dégradations ou anomalies peuvent se produire. Le jeu retrouvera cependant son état normal de fonctionnement lorsque la cause de ces anomalies aura cessé ou se trouvera déplacée.

Not Si le processeur du jeu se reprogramme suite a une interruption ou une réduction de l'alimentation, les crédits qu'il aurait pu contenir peuvent se trouver perdus.

Ce jeu n’est pas une machine, telle que définie par la norme sur les machines 89/392/EEC

MESURES DE SECURITE

Afin d'utiliser ce jeu en toute sécurité, bien lire ce manuel d'utilisation avant de procéder a son installation, son réglage ou son exploitation. Si le propriétaire de ce jeu en confie la demontage, installation, le réglage ou la maintenance habituelle & une autre personne, il devra s'assurer que cette personne ait lu les conseils d'utilisation et les passages du manuel se rapportant a ce théme, avant qu’elle ne commence son travail. Afin d’éviter tout accident pendant la durée d’exploitation de ce jeu, se conformer strictment aux conseils de sécurité décrits a la suite. Ce manuel ainsi que le manuel d'installation du jeu (la o nécessaire) font partie des éléments nécessaires a l'installation de la machine et doivent étre mis a la disposition de ['utilisateur et du personnel de maintenance a tout moment. Ce jeu est uniquement destiné a un usage intérieur et devra étre utilisé comme tel. Namco Ltd. ne sera aucunement tenu responsable en cas d’accidents, de blessure ou de dommage quelconque résultant de modifications non autorisées ou d'usage impropre du jeu.

REMARQUES SUR LA SECURITE

Les termes de sécurité détaillés a la suite seront utilisés tout au long de la lecture de ce manuel. Il convient de vous familiariser aves chacun de ces tetmes ainsi que leur signification avant de procéder a installation, & la maintenace ou au réglage du jeu

AVERTISSEMENT /\ Ce terme annonce un danger qui pourrait éventuellement avoir des conséquences dommageables ou mortelles. Ne pas passer oiltre ce signal jusqu’a ce que les conditions indiquées soient entiérement comprises et effectuées.

ATTENTION O) Ce terme indique qu’un danger menace la machine. Ne pas passer oltre ce signal jusqu’a ce que les conditions indiquées soient entiérement comprises et effectuées.

CONSIGNES GENERALES DE SECURITE

A\ Allumer l'appareil seulement aprés avoir vérifié qu'il a été correctement installé, et que les instructions du manuel ont été respectées

> Certaines piéces du jeu bougent quand jeu est en fonctionment, il y a donc des endroits oui la distance entre la zone stationnaire et la zone en mouvement change. Il existe des notes de mise en garde pour les mains et pieds sur les piéces en mouvement. Cependant si l'opérateur pense qu'une personne court un danger, il doit l’en avertir.

Les notes de mise en garde doivent constamment demeurer en bon état et étre remplacées en cas de disparition, afin que le client puisse les lire clairement.

S'il y una erreur ou un probléme avec la machine, l'utilisation doit étre immédiatement interrompue et le probleme résolu avant toute nouvelle utilisation.

L’installation, le service, le réglage, ou la maintenance doivent étre effectués uniquement par les personnes qualifiées.

Afin d’éviter un éventuel incendie, s'assurer que les fusibles soient remplacés par le méme type de fusibles et au bon voltage. L'utilisation d'autres sortes de fusibles ou autres matériels est interdite.

L’alimentation a l’intérieur du moniteur reste chaude et comporte des zones de haute tension méme si la machine est éteinte. Il existe donc un risque de brulure ou d’électrocution. Attention a ne pas toucher ces endroits.

Pour prévenir une éventuelle électrocution due a un défaut matériel, ce jeu DOIT étre muni d’une prise de TERRE connectée en toute sécurité

Si A tout moment les fils électriques sont endommagés, il faut les remplacer immédiatment

Ne pas mettre le jeu en mode de fonctionnement avant qu’il n’ait été correctement installé. OPP BBB BP BE B&

Avant de connecter la machine au réseau, s’assurer que la machine est installée sous la bonne tension et que les fusibles correspondent.

Page 13
Note: NOTES D’ INSTALLATION

NE JAMAIS mettre le jeu en marche avant que l'installation ne 1 soit complétement effectuée. {

Afin de prévenir une éventuelle électrocution, s'assurer que la machine est connectée au réseau avec une prise de terre relige | selon les normes de sécurité. le

Afin que les clients ne soient pas blessés par les mouvements du jeu, s'assurer qu'il existe au moins 500mm de séparation = aves les autres jeux ou les murs. - -

Afin d’éviter que la machine ne soit abimée suite a une mauvaise opération, s'assurer que la tension sur le réseau principal soit de 230 volts AC.

Si 'endroit ou doit étre installée la machine a un sol pdli, il est recommandé de poser des tampons feutrés sous les vérins pour éviter que le jeu ne glisse sur le sol

Afin de facilité l'accés aux CPU at a l’alimentation, s’assurer qu'il y a un espace d’au moins 500 mm entre I’arriére du meuble et le mur ou — tout autre jeu.

Le jeu est foumi avec des roulettes pour une meilleure mobilité. Prendre garde quand la machine est déplacée sur une surface inclinée.

Le centre de gravité de la partie supérieure du jeu est situé sur l’avant, il est donc indispensable que deux personnes au moins soient employées pour installer ou déplacer la partie supérieure.

L'installation de la partie supérieure du jeu s’effectue en hauteur, il est donc important d’utiliser un élevateur quelconque pour en effectuer le montage.

La hauteur totale de l'assemblage principal est de 1990mm, prendre garde aux encombrements de la partie supérieure (ex : illuminations du bandeau).

Quand le jeu est déplacé ou transporté, s'assurer qu'il est séparé en 3 parties: l'assemblage du haut (le bandeau), l'assemblage de devant (la cabine), l'assemblage mobile. S

PRP BBP BP BP Be B& DEPLACER ET REMPLACER LES UNITES ET LES PIECES DETACHEES.

L'installation, le service, le réglage, ou la maintenance doivent étre effectués uniquement par les personnes qualifiées.

Ne pas apporter de modifications sur cette machine sans autorisation préalable, faute de quoi cela pourrait entrainer un danger

Seules les piéces détachées Namco Europe Ltd. doivent étre utilsées pour le remplacement ou la réparation de piéces (y compris les vis)

S'assurer que l'interrupteur soit sor OFF avant de commencer tout travail de maintenance (localisation d'une panne, réparations, etc.)

Si dans ce manuel il manque une information pour réaliser un quelconque travail, contacter votre distributeur, car aucune responsabilité ne sera acceptée en cas de domage ou de blessure.

Les piéces de |’alimentation et du moniteur restent chaudes, a tension élévée méme lorsque la machine est hors tension, elle pourrait occasionner des brilures ou des électrocutions. Attention de ne pas toucher ces endroits accidentellement.

S’assurer que la machine soit hors tension avant de brancher ou débrancher toute prise ou connecteur.

Lorsque l'on manipule la prise au réseau de la machine, ou lorsque les prises principales doivent étre débranchées, saisir toujours la prise, et non le cable. ~\

w

Page 14

Kavéva pépos avtiig ms éxdoans Sev pmopei va avanapayOel pe omoWdH MOTE |MZAVIKS ,POTOYPAGIKS H NLEKTPOVIKE [LEGO , H HE HOP GovNTIKs NZoYPaPHaNs Kat obtE va anoONKEDTE: He ENaVOPHOTIKO GbaTHHEL , Va LETASOBEt 1 Va avttypaget ya SHpdoIEG H WroTIK! zpi}on , opis my dev tag NAMCO EUROPE LIMITED.

Kadts avrés ot tanpopopies oe avtd to eyerpidto éyouv Soei we KaAA mioTH KL aKPIBag THY dpa THs THnMANS , n ETUIpE!A NAMCO EUROPE LIMITED xpataet to dikaiopa va Kaver onorecdinore adhayés opis erdonoinan,

Ta pnyaviipata éxovv KatacKevactel cppava je Tous pone Hs Evpamaixys Kowdrytag , Kat Exovv eheyDel cbppova pe Tos VoLoug 89/336/EOK kat 72/23/EOK pe my aitnon tov ENSS014 , EN55104 Kat EN60335-1 otavtapts (Ses jimpoata oto eyze\pid10) Kai ha Exovv to CE onpa . Onoadiinote adLayi H petatpom} ce avd to uNZévnpa mpéret va eivar copOOV HE TOUS Opovg THs Evpanaixiys Kowotntac, Oxotecdinore adkayés yopic ddera ce aut to mpoldv nope’ Va Mupapei avtOvS TOVs dpoUs. Ze Knots nepimtdoers vmepPokuaje etworeprrig Rape Podiig ,7.7, pudlopovixés petaddaets , NrextpootatiKés pETAPOREs H MapodtKés EUBORES , Hmopei va mapovaiaotoby Kano1Es aOAOTHTES oTHYTAPOVGIaGN . Tdvta< To jMLavN}LA Oa. EMAVEAIEL GtHY PLALOAOYLKH TapOvGiaEN Ep GOV AMY THE mapELPoAAs oTapaTHGEL 1 aRopaKpoVOE .

Enueiaon : Edy yivet reset otov processor tov pn Zavijpatos KaTé TH StapKeIa THE KOpIag RapOZIs , NoVTOI ToD éxovv KEpdnOei propeEt va zaboov.

Avté to naryvidt dev civar pnZavnpa dnos mpoodtopiCerat and tovg dpovg Myzavypétov 89/392/EOK .

OAHTIEY ALMAAEIAL

Pa thy aopadi xprion tov pngaviiparos , xpéner va diafdaers to eyxerpisio ypHang mpooEKTIKG API THY EyKATaETUGH ,tonoDETHAN F ZPHION TOD aviyporto. Ono rors © WioKrieNs avto0 Tov LNZavH|ATOS CyTaEL ANd KémOI0 TPdGeRo Va EyKaTUGTIOEL , Va KavEL OROLUd!TOTE arLaYA H édeyZO povtivas oto ymyavnpia , mpéner va. civat ciyoupos dui éze1 StaBdoet Tig Odnyies avtOd Tov eyxe1pdiov mpwv va apyioet va ovdE Tpog axopuyiy oxotovdirore atuziwatos Katd THY AeITOUpyia. TOV |NZAVAHATOS , avoTHPas UKOAOLDODVTAL OL OdNyiEs ao~PAAELAS dna< divovtat napaKéco . Avté 10 eyzeipidwo at ovvdvacpd We to eyze1pib10 eyKaréotaaNs (Snov duetiDeTa1) anotedei Eva OLOKANPOREVO LEpos TOV RapoOYov Kat mpénEL va. civat diadésyio 1a Thy Aettovpyia Kat to service omoidixoTE oTLYLN. Avté 10 pngavnja evan p1a YpHON LSVO GE eowtEplKG ZApO Kat Oa MPEREL Va. YPHOYLOROLEItaI LSVO 1a. Tos A6YOUS yta TOUS Omo{oUg KaTaoKevdatnKe. H_eraipeia NAMCO Ltd dev pépet Kapia evdivy ya atuyhpata , mAnyés H KatAatpOGés AOD HiRopEt Va mPoKANDOdY and arAayés Zopic dea Ge H e1ayeyeig avtod tov pNyZaviiLatos

XHMEIQLEIL AL@AAEIAL

O1 axdhovdes onperdsers aogddcrag ypnoyonoodyea pécw avtod tov eyfeiprdion . AtéPuce avtés npooeKTIKG ya. va. yiveL Kotavontd to voNHG Tous APL THY EyKUTHOTAGN , GépfIC H OnoLAdH|ROTE AdAUyH yiver oto LN ZavHLA.

TIPOEIAONOIHEH /\ H xposidoroinan apopé Kivévvo o onoiog propsi va sivar R6yos Oavarou . Na wy mpozapiiesis o& onowadyrote Kivyoy pézpL avtoi or Spor yivovv KatTavonToI.

TIPOZOXH GH xposoxh agope kivSuvo o oxoi0g ptxopet va xpoxadécet mpOPAnpia oto jngavngia . Na nv mpoyaphosic of onowdr}xore Kivnon stézpt avtoi o1 Spot yivovv Katavontoi.

EEETAZH PENIKHE AZ@AAEIAD

> Agod é721 KatavonBei avtd to eypeIpidi0 , pévo TétE va LeLToUpyHoet To UNZavHRA H Va iver EAEYL0s Ep daov Eyer yiveL H eykatéstasn.

> Mépn tov pngavinatos petaxwoovtan Katd Thy dépKeLa evos aLZVIdION , étOL Gore va. UMapZovV pépy 6xov y andotaOH pETAED Tov HEpovs GTAOEVENS Kal TdzOD KivyGHs Va HrOpEt va arAACEL . Yrapyovv npoeidoroujoeis va eivar ta 7épia Kat Ta T6dLA. HaKprd an6 ta pépy nov KWodvTaL, dpos 0 iOKTITHS NpéneI Va EhEYLEL LV KAmOLOg KISDVEIEL Va TOV ELdOTONI|SEL KA Va TOV aropakpiver .

Ot xposdonoujoris npéxei va pévovy Kabapss KaL GE Kaa} KaTéSTUOH ote o neddTMS va TIS LapaCEL KaBapG.

Ey vmépyet 2.400¢ mpopinna pe to pNZavyHA, y Aettoupyia mpénst va ctapaTast apésos Kat va dtopBGveTaL to L480s mp_W onovadynote 22 zon.

Eykaréotaon , petatpomi ¥ éAeyZ0s povtivas unopei va yivetan povo axé cLoverodoTmpéva drone «

Tia ovvep} mpootacia and pond , mpéner o1 aspadsies va avtKaBLotosvTUL JIE {dtOD THnOD .H pron G).OV aogarsidv H aytiKeipévov anayopsveta.

To tpopodoniké oto cowtepiKé tov jZavyjnatos Oa mapapciver Ceots KaL vRdpovv mepLozés WE DYNPa} Téon RAp"6L0 TOD TO mnzavqna dev dovdcber , Kai vndpyer | MOavStHTA NaEKTpLKOD GOK . HIposoy Va UY akODpMaEIC ATE TIs nepLozés.

Tia Ty anogvy) nhextprKdy cox L670 BLGPN , To j|ZavNH TIPENEL va ézet mpOra eves pe yeioon.

Edy Kénowa otty} Kataotpagei n KOpLa napoyi , mpénEL va avtIKaTasTUOEi apésos.

Na py avayer to pryzavnpa (switch ON) pézpr va ézet eyKataotadE! coord Kat Mia}pas.

Tpw thy napoxi pedpatos oto ungavnpa , va eicat aiyoupoc S11 ta voltage Kat dkes ot agpédeLEs civar caoté evepéva KaL tonoletmpéva. OPE BP BB BBE

Page 15

~

>be -

0) ZHMEIQLEIS PIA THN ET KATAZTAZH 1 manor 4

TOTE va jy avaper to pyzavypa cay dev ée1 odoKANpOdei y sykatéetaon. i Tia thy axopvyy nhextpiKdy cox mpémet to pNYavnna. va éyer yeroded.

Tia thy anopvyy KwSdvon oe Kéxo1ov naiKty , mpénet to uZavypa va ker = 8 8 axdotacy tovddzistov 500mm and 62.0 unZavn}a H TOizZ0. wel | Tia ty anoguri Pans ovo wnzioma by0 AAos erroupying , mpénst mapoyt va evan 230volt AC

ZHMEIOSH: Edy to nétopa oto onoio civat toxodempévo to jmZavnpa yLuotpaer,civat

ZHMEIOSH: Pa thy cdKodn apdaPacn omy Kvpiag napor Hy to CPU aj KOKO Va. purer éva. KOPATI HOKETUS ya aTOQUYH HLETaKivnGNS TOD jmZavipwatos ev dpa Aettoupyias tov

etn tio@ OPtA TOV HHZAVi|NATOS va aRExEI TOVAGOTOV 500MM and tov toiz0 H GiQo pnzavnte.

>Re BBE BE To wnzavqna civar cpodiacpévo te Kapodiia ya THY cbKOA.N [ETaKiv|GH TOD.

To exdveo pépos tov jmzavtinatos és emmd£ov Papos pavtd zperdtovtar dbo ya THY HETAPoPA.

H kepady (kandxt) tov pnzavijnatos civar noAb WNP6 Kar Lats ypeLdCera mposoy oTHY ToROBETHAH TOD , va. IV qeomost H katastpagei.

To avvonixé dos THs KEQads iva 190mm . Opévtise va pyV ZroMoEL GE Kapines KAT.

‘Otay petaxieitat to pyZavqna., mpénet va civar os 3 pépn: —Kepada (kandKt), Mapooté Epos (o86ves), Kéiopa

be BP BRP BBB ATIOMAKPYNZH KAI ANTIKATALTALZH MEPON - ANTAAAAKTIKON

Eykaréotaon , netatpom} Hf éheyyos poutivas wxopet va. yiverar pévo ané sZoverodoTmHEva Gropa .

Aey apénei va yivovrar petatponés ota wnzavinata opic EyKpion . Mropei va npoKinOei anpoBientoc Kivevvos.

Mévo pépy nov dtevxpwiGovtar and thy etaipcia NAMCO EUROPE Ltd propoty va zpnomonompody ya ayriKatéataan i emd.6p0oon. (cvMTEPU.apPavovre Kat o1 Bids)

Na sivan oiyoupa k2e1676 to pebpa mpi onoiadiitoTe Sov).£16 oto ZavnWA.

Eay yiver kéroia dovdc16 ot pZavana Zopic va dtevKpwierar oto eyyeipidio , va emKOWEVi\aEIs HE TOV aytizpécono ya odnyics lati Kapia cvdivy dev PEpovpe ya KataGtpOgés H BLABES.

Mépn tov tpogodotuKod # tov w6vitop nupapévouy Ceotd 1 Exouv vyNdi TAOH UKOpA KaL STAY oPi\szt To HHZdv|BE Kal jtxopovy va MpoKadésovv KayNpo i AeKTPOGOK.F AUTO dev MpénEL va EpyovraL Ge EnapH WE ZEpLa.«

To wnzavnua xpénci va civar oBnot6 Kata THY GbvdEGn H anoGsvdcon mpiac H KovéKTOpA.

Kara thy anopaxpoven tov Kevtpuxdy KovéKtop axé to unZavnna H THs KUpiag RpiLas , mpéneI va mavoupE to mhastiK6 Lépos Kat 671 To KaAABLO. ~

Page 16

@ Nessuna parte di questa pubblicazione pud essere riprodotta con processo meccanico, fotografico o lettronico, né sotto forma di registrazione fonografica, nd pud essere memorizzata in un sistema di salvataggio, trasmessa o in altro modo copiata per uso pubblico 0 privato, senza l'autorizzazione di NAMCO EUROPE LIMITED. Le informazioni contnute in questo manuale sono state date in buona fede ed erano accurate al momento della pubblicazione. Tuttavia NAMCO EUROPE LIMITED, si riserva il diritto di apporre cabiamenti e variazioni senza alcun preawviso.

Questo apparecchio é stato costruito in conformita alle Direttive della Comunita Europea, ed @ stato provato e soddisfa le Direttive 89/336/EEC e 72/23/EEC per l’'applicazione degli standards delle norme EN55014, EN55104 e EN60335-1 (vedi fronte del manuale), e per questo porta il marchio CE. Qualsiasi cambiamento o modifica di questo apparecchio deve essere in conformita con le Direttive della Comunita Europea.

In caso di condizioni di estrema interferenza dall'esterno, per esempio trasmissioni radio, scariche elettrostatiche o transitori sulla linea, pud verificarsi un decadimento delle prestazioni. Comunque l'apparecchio ritornera al rendimento normale quando la sorgente dell,interferenza avr cessato di emettere o sara stata rimossa.

Nota bene: se il processore del gioco “resetta” a causa di una interruzione o diminuzione del voltaggio di linea, un eventuale credito, gia concesso, pud essere annullato.

Questo goco non é una macchina cosi come viene definita dalla Direttiva Macchine 89/392/EEC.

AVVERTENZE PER LA SICUEZZA

Allo scopo di usare questo apparecchio in sicurezza, leggere questo Manuale dell’operatore attentamente prima dell’installazione, regolazione 0 uso di questa macchina. Tutte le volte che il proprietario di questo apparecchio affida lo smontaggio, l'installazione, la regolazione o la manutenzione ordinaria ad un’altra persona, il proprietario stesso deve assicurarsi che quella persona legga le precauzioni necessarie e i paragrafi importanti di questo manuale prima di iniziare a lavorare. Perché non succeda alcun incidente quando la machina é operante, seguire rigorosamente le note sulla sicurezza come specificato piu avanti. Questo manuale insieme con il manuale di installazione (dove si pud applicare) forma una parte integrante dell'apparechio e deve essere disponibile sempre al personale operante e di servizio. Quest macchina deve essere usata solo in interni e deve essere usata solo per gli scopi per cui é progettata. Namco Europe Ltd non si assume responsabilita per incidenti, ferite o damni risultanti da cambiamenti non autorizzati o da uso improprio della macchina.

NOTE PER LA SICUREZZA

Le seguenti note sulla sicurezza sono usate dal principio alla fine di questo manuale. Valutare attentamente ciascuna di queste note ed il loro significato prima di installare, fare assistenza o regolazioni su questa macchina.

WARNING /\ “Warning” evidenzia un rischio di ferita 0 di morte. Non procedere oltre una nota “Warning” finché le avvertenze specifcate non siano completamente capite e conosciute.
CAUTION (4) “Caution” evidenzia un rischio di danneggiare la macchina. Non proceder oltre una note “Caution” finché le awertenze specificate non siano completamente capite e conosciute.

CONSIDERAZIONI GENERALI SULLA SICUREZZA

Mettere in funzione l’apparecchio solo dopo aver controllato che |’installazione sia stata effettuata correttamente ed in conformita alle istruzioni del manuale.

Parti di questa machina si muovono durante il gioco, quindi ci sono posti dove le distanze tra la parte fissa e quella mobile cambiano. Ci sono avvisi “Warning” di tenere mani e piedi lontani dalle parti mobili, comunque se V'operatore crede che una persona sia in un qualche pericolo, deve avvisare quella persona.

Gli avvisi “Warning” devono sempre essere conservati in buone condizioni e sostituti se consumati, cosicche il cliente li possa leggere chiaramente. Se vi sono errori o problemi con la macchina, si deve interrompere il funzionamento immediatamente e risolvere il problema prima di ogni ulteriore uso.

L’installazione, l'assistenza, le regolazioni e la manuzenzione ordinaria devono essere eseguite solo da persone idonee e qualificate.

Per una protezione costante contro il rischio di fuoco, assicurarsi che i fusibili sulle alimentazioni siano solo sostituiti con lo stesso tipo e caratteristiche. L’uso di altri fusibili o materiali é proibito.

L’alimentatore all'interno del monitor rimane caldo ed ha zone di alto voltaggio anche se la macchina é stata spenta, c’é quindi la possibilita di bruciature o scosse elettriche. Fare attenzione a non toccare queste zone

Per prevenire possibili scosse elettriche dovute a difetti, quest macchina DEVE essere installata con un connettore sicuramente MESSO A TERRA.

In caso il cavo di alimentazione di rete risultasse danneggiato deve essere sostituito immedatamente. bPRPBBBPBBP BP BB

Non accendere la macchina finché la stessa non é stata installata completamente e correttamente. ©) Prima di collegare la macchina alla rete, assicurarsi che la machina sia preparata per il voltaggio corretto e che siano inseriti i fusibili adatti.

Page 17

Oo FP EB

Note:
Note: NOTES D’ INSTALLATION

NON ACCENDERE MAI la macchina finché l’installazione non é stata completata. - - - ;

Allo scopo di prevenire possibili scosse elettriche, la macchina deve essere obbligatoriamente collegata alla rete con un Go

connettore messo a terra con connessioni sicure. say sere

Perch i clienti non siano feriti dal movimento del gioco, assicurarsi che ci siano almeno 500mm di distanza rispetto alle altre macchine o rispetto al muro.

Per evitare danni alla macchina durante la messa in opera, } eed eee assicurarsi che il voltaggio della rete sia 230 volts AC.

II luogo di destinazione della macchina deve avere il pavimento liscio e si raccomanda di sistemare dei cuscinetti di gomma sotto i piedini di livellamento per prevenire lo sciovolament della machina sul pavimento.

Per garantire l'accesso all’alimentatore e alla scheda madre, assicurarsi che il retro del mobile principale sia separato dalla parete 0 da altre macchine di almeno 500mm.

(pe pb bp > Bp | ll gioco é fornito di ruote per rendere piu facile il suo spostamento. Fare attenzione quando si muove la macchina su una superficie inclinata.

La testata ha il baricentro spostato in avanti, é percid importante che ci siano almeno 2 persone per montare o smontare la testata stessa.

La posizione di fissaggio della testata é molto alta, ed é importante che ci sia un mezzo disponibile per raggiungere tale altezza in sicurezza e senza allungamenti. (Ad esempio scalini, scale portatili etc.)

L’altezza totale della parte principale é 2310mm, fare attenzione ad eventuali ostacoli soprala testata ovvero ad eventuali installazioni di luci.

Quando si muove o si trasporta il gioco assicurarsi che sia smantato in 3 parti: Testata, Parte frontale, Parte mobile ~\

S

>BP BBB BBE RIMOZIONE E SOSTITUZIONE DI GRUPPI E PARTI STACCATE

Liinstallazione, l’assistenza, le regolazioni e la manuzenzione ordinaria devono essere eseguite solo da persone idonee e qualificate.

Non apporre alcuna modifica alla macchina senza autorizzazione preventiva. Il fare questo pud causare un pericolo non prevedibile.

Quando si rimpiazza o si riparano delle parti (incluse le viti) si possono usare solo parti approvate dalla Namco Europe Ltd

Assicurarsi che la macchina sia SPENTA prima di incominciare qualsiasi lavoro di manutenzione (guasti, riparazioni etc.)

Se state per iniziare un lavoro non descritto in questo manuale, contattate il vostro distributore per instruzioni poiché non si accetta alcuna responsabilité per danni o ferite. Parti dell’alimentatore e del monitor rimangono caldi o portano alta tensione anche dopo aver spento V'apparecchiatura e possono causare bruciature o scosse elettriche. Attenzione a non toccare queste parti accidentalmente.

Assicurarsi che la machina abbia l'interruttore nella posizione OFF prima di inserire o disinserire qualsiasi connettore o spina.

Quando vengono rimossi i connettori principali dalla machina oppure la spina dell’alimentazione dalla parete bisogna sempre afferrare il connettore e non il cavo. ~\

w

Page 18

@)

Ingen del av denne utgivelsen ma reproduseres av noen mekaniske, fotografiske elle elektroniske prosesser, eller i form av fotografiske opptak, og ikke kan det lagres i et gjenvinnbart system, sendt eler kopiert for offentlig eller privat bruk, uten tillatelse fra NAMCO EUROPE LIMITED.

Da informasjonen i denne manualen er gitt i god tru og var korrekt da den ble utgitt, tillegger NAMCO EUROP LIMITED seg retten til A lage forandringer uten varsel.

Denne maskinen er produsert i samsvar med direktiver framsatt av det Europeiske samfunn. Maskinen er testet og samsvarer med direktivene 89/336/EEC og 72/23/eec med anvendelse av EN55014, EN55104 og EN60335-1 standarder (se i begynnelsen av manualen), og derfor beerer CE merket. Hvilken som helst forandring eller modifisering ma skje etter direktivene sat av det Europeiske samfunn. Uautoriserte forandringer pa dette produktet, kan motstride disse direktivene.

Under noen forhold av ekstreme ytre forstyrrelser, f.eks radio sendere, elektronisk utladning eller transiente spenninger, kan man regne med noe senket ytelse. Men maskinen vil oppna normal ytelse nar kilden til forstyrrelsene opphorer eller er fysisk fjernet.

Merk:- Hvis spillets prosessor resettes p.g.a et Kutt eller reduksjon av hovedspenningen kan oppsparte kreditt pa spillet forsvinne.

Dette spillet er ikke en maskin som er definert ved Maskin direktivet 89/392/EEC.

Sikkerhets advarsel.

For 4 bruke denne maskinen uten noe form for fare, sorg for a lese denne manualen noye for installasjon, justeringer eller bruk av maskinen. Nar eieren av denne maskinen overlater avmontering, installasjon, justering eller rutine vedlikehold til en annen person, skal eieren forsikre seg om at denne personen leser de passende forsiktighetsteglene og relevante deler av manualen for han starter pa arbeidet. For a forhindre at ulykker inntreffer nar maskinen er i drift, folg strengt teksten om sikkethet som beskrevet nedenfor. Denne manualen sammen med installasjons manualen (hvor det er anvendelig) er en intrigert del av utstyret og ma vaere tilgjengelig for drift- og servispersonell til alle tider. Denne maskinen er bare for innendors bruk og skal bare benyttes etter mente hensikter. Namco Ltd. beerer intet ansvar ved ulykker, kvestelse eller skade som folge av uautoriserte forandringer, eller for uriktig buk av maskinen.

Sikkerhets beskjeder.

Folgende sikkerhets punkter er brukt ut denne manualen. Gjor deg kjent med disse punktene og deres mening for installasjon, service eller du utforer noen innstillinger pa denne maskinen.

ADVARSEL /\ Advarsel innebeerer en risiko som kan fore til kvestelse eller dod. Ikke fortsett utover advarslen for den er ordentlig forstatt og mottiltak er igangsatt. FORSIKTIG ({) _ Forsiktig innebeerer en risiko som kan medfore skade pa maskinen. Ikke fortsett utover advarslen for den er ordentlig forstatt og mottiltak er igangsatt.

VANLIGE SIKKERHETSTILTAK

Bruk bare denne maskinen etter a ha kontrollert at den er korrekt installert ifolge manualen.

Deler av denne maskinen er i bevegelse under spill, det er derfor plasser hvor avstanden mellom de stillestaende deler og bevegelige deler forandres. Det er plassert skilt med advarsel for a holde hender og fotter borte fra bevegelige deler, men uansett skal operatoren varsle vedkommende hvis han foler at han er i noen form for fare.

Advarsel skiltene ma bestandig holdes i skikket stand og eventuelt byttes ut hvis det oppstar skade pa dem, slik at kunden uten vanskelighet kan lese dem Hvis det er en feil eller et problem med maskinen, ma den straks settes ut av funksjon. Og ma under ingen omstendigheter startes for problemet er rettet pa.

Installasjon, service, justering eller rutine vedlikehold skal bare utfores av kvalifiserte personer.

For fortsatt beskyttelse mot brann, forsikre deg at hoved sikringen bare byttes ut med en av samme type og verdi. Bruk av andre sikringer eller materiale er forbudt.

Stromforsyningen inne i monitoren vill vzere varm og ha omrader med hoy spenning selv om maskinen har blitt slat av. og det er muligheter for skader og elektriske sjokk. Veer forsiktig s du ikke berorer disse omradene. For a forhindre mulige elektriske sjokk grunnet funksjonsfeil, ma denne maskinen vzere ordentlig jordet Hvis ledningen til hoved stromforsyningen skades ma den straks byttes ut.

Ikke sla pa maskinen for den er korrekt installert.

For du kopler maskinen til stromnettet, forsikre deg om at maskinen innstilt for den korrekte spenningen og de riktige sikringene benyttes. OPBPP BP BBB Be BB

Page 19

MERKNADER VED INSTALLASJON

Sla ALDRI pa maskinens stromforsyning for installasjonen er t r fullfort. pases seers

For & forhindre eventuelle elektriske sjokk, forsikre deg om at =

maskinen er koplet til et stromnett med ordentlig jording. ——

For & forhindre at kundene blir skadet av spillets bevegelige deler } forsikre deg om at det er minst 500mm avstand mellom andre s =8 5 maskiner eller vegger. ag Oo PE -

For a fothindre skade pa maskinen p.g.a. feil bruk, sorg for at spenningen

til hoved stromforsyningen er 230Volt AC.

MERKNADER: Hvis plassen hvor spillet skal plasseres har polerte gulv anbefales det at du benytter gummi sko under niva justeringene, for a forhindre at maskinen kan flytte pa seg.

MERKNADER: For a f& adgang til stromforsyningen og CPU-kort, forsikre deg om at bakparten av hoved kabinettet er skilt fra vegger eller andre maskiner med minst 500mm.

Ns y,

Spillet har montert hjul for A gjore det letter & flytte pa. Hver forsiktig nar det skal flyttes pa en hellende overflate.

Hoved enheten i spillet har tyngdepunktet i fronten, sd det er viktig at minst 2 personer blir brukt til 4 montere eller flytte denne enheten.

Monterings posisjonen til hoved enheten er veldig hoy, og det er viktig at denne hoyden nas sikkert, uten at man ma strekke seg. Benytt deg av hjelpemiddel. (f.eks sto, krakk, gardintrapp osv)

Den totale hoyden pa hoved enheten er 1990mm. veer forsiktig med hoye hindringer som f.eks lysror.

Nar spillet skal flyttes, forsikre deg om at spillet er delt i 3 deler: Topp enhet, Front enhet, Hoved enhe PRP EPP B&B

FJERNE OG UTSKIFTE ENHETER OG DELER.

Installasjon, service, justering eller rutine vedlikehold skal bare utfores av kvalifiserte personer.

Ikke lag noen forandringer pa denne maskinen uten godkjenning. Dette kan medfore uforutsette farer.

Bare deler spesifisert av Namco Europe Ltd. skal benyttes ved utskifting eller reparasjon av deler (dette gjelder ogsa skruer).

Forsikre deg om at strammen er slat av for du pabegynner noe som helst vedlikeholdsarbeid (feilsoking, reparasjon osv.)

Hvis du utforer arbeid som ikke er beskrevet i denne manualen, ta kontakt med din distributor for instruksjon da ikke noe ansvar vill bli akseptert for skade pa maskin eller pa personer.

Deler av stromforsyningen og monitoren er fortsatt varm eller beerer hoye spenninger selv etter strommen er slatt av og kan forsake skader eller elektriske sjokk. Forsikre deg om at du ikke berorer disse delene.

Forsikre deg om at maskinen er slatt av for du kopler sammen eller tar fra hverandre plugger eller koplinger. >Re BBP BP PBB

Nar du fjerner hoved koplingene fra maskinen, eller hoved pluggen fra stopselet, ta bestandig tak i LL pluggen og ikke ledningen.

Page 20

@D Niets uit deze publikatie mag worden gereproduceerd door enig mechanisch, fotografisch of electronisch proces, of in de vorm van een fonografische opname, noch mag het opgeslagen worden in een retrieval systeem, doorgezonden of anderszins gekopieerd voor publiek of privégebruik, zonder toestemming van Namco Europe Limited.

Ofschoon de informatie in deze handleiding in goed vertrouwen is gegeven en nauwkeurig was ten tijde van het drukken, houdt Namco zich het recht voor om veranderingen en aanpassingen te maken zonder bericht.

Deze machine is geproduceerd volgens Richtlijnen van de Europese Gemeenschap, en is getest en is in overeenstemming met de Richtliinen 89/336/EEC en 72/23/EEC door de toepassing van de standaards EN55014, EN55104 en EN603365-1 (zie voorin de handleiding) en draagt als zodanig het CE-merk. Enige veranderingen of aanpassingen aan deze machine dienen in overeenstemming te zijn met de Richtlijnen van de Europese Gemeenschap. Enige ongeauthoriseerde veranderingen aan dit produkt kunnen in strijd zijn met deze Richtlijnen.

Onder sommige omstandigheden van extreme externe storingen, bijv. radiotransmissies, electrostatische ontladingen of pieken op het net, kan prestatieteruggang optreden. De machine zal echter normaal presteren zodra de storingsbron gestopt of verwijderd is.

Let op: - als de spelprocessor reset a.g.v. een onderbreking of vermindering van de netstroom, dan kunnen opgebouwde credits verloren gaan.

Dit spel is niet een machine zoals omschreven in de Machinery Directive 89/392/EEC.

Veiligheidsopmerkingen Om deze machine veilig te kunnen gebruiken, dient voor installatie, aanpassing of gebruik van deze machine, de Bedieningshandleiding Zorgvuldig gelezen te worden. Telkens wanneer de eigenaar van deze machine de demontage, installatie, aanpassing of routine-onderhoud toevertrouwd aan een andere persoon, dient de eigenaar er voor te zorgen dat deze persoon de juiste voorzorgsmaatregelen en relevante gedeeltes uit de handleiding lest voordat hij begint. Om er voor te zorgen dat geen ongelukken gebeuren als de machine gebruikt wordt, dienen onderstaande veiligheidsaanwijzingen Zorgvuldig opgevolgd te worden. Deze handleiding maakt samen met de installatiehandleiding (waar van toepassing) een integral deel uit van de apparatuur en moet te allen tijde ter beschikking staan van exploitatie- en onderhoudspersoneel. Deze machine is alleen bedoeld voor gebruik binnenshuis en dient alleen gebruikt te worden voor bedoelde doeleinden. Namco Ltd. is niet verantwoordelijk voor ongelukken, letsel of schade die voortkomt uit ongeoorloofde veranderingen aan of onjuist gebruik van deze machine

Veiligheidsopmerkingen

De volgende veiligheidsopmerkingen worden overal in deze handleiding gebruikt. Maak uzelf vertrouwd met deze opmerkingen en hun betekenis voor installatie, het plegen van onderhoud of het aanbrengen van aanpassingen aan deze machine.

WAARSCHUWING A Waarschuwing geeft een gevaar aan dat zou kunnen resulteren in letsel of de dood. Ga niet verder dan een waarschuwingsopmerking totdat de aangegeven omstandigheden volledig begrepen zijn en hieraan voldaan is.

VOORZICHTIG —(F)_Voorzichtig geeft een gevaar aan dat zou kunnen resulteren in schade aan de machine. Ga niet verder dan een voorzichtigheidsopmerking totdat de aangegeven omstandigheden volledig begrepen zijn en hieraan voldaan is

ALGEMENE VEILIGHEIDSOVERWEGINGEN

Stel deze machine alleen in gebruik nadat gecontroleerd is of de machine correct en overeenkomstig de handleiding is geinstalleerd. > & Gedeeltes van deze machine bewegen tijdens het spel, waardoor er plaatsen zijn waar de afstand tussen het stilstaande gedeelte en de bewegende sectie verandert. Er zijn waarschuwingsstickers om handen en voeten van bewegende delen af te houden; als de exploitant echter van mening is dat iemand in gevaar is, dan dient hij deze persoon dienovereenkomstig te waarschuwen.

De waarschuwingsstickers dienen altijd in goede staat te worden gehouden en vervangen indien versleten, zodat de klant ze goed kan lezen.

Als zich een fout of probleem voordoet met de machine, dan dient de machine onmiddellijk stopgezet en het probleem verholpen te worden voordat de machine verder gebruikt wordt.

Installatie, service, aanpassingen of routine-onderhoud dient alleen uitgevoerd te worden door hierin bekwame personen.

Om blijvende bescherming tegen brandgevaar te garanderen, dient ervoor gezorgd te worden dat de netzekeringen alleen vervangen worden door zekeringen van hetzelfde type en dezelfde sterkte. het gebruik van andere zekeringen of ander materiaal is verboden.

UlTgeschakeld is, waardoor er brandwonden of electrischee schokken kunnen worden opgelopen. Ben voorzichting en raak deze delen niet aan

Om mogelijke electrische schokken a.g.v. storingen te voorkomen, MOET deze machine voorzien zijn van een goed vastzittende aardstekker.

Mocht het netsnoer op enig moment beschadigd worden, dan moet deze onmiddellijk vervangen worden.

Zet de machine niet AAN totdat deze correct is geinstalleerd.

Voordat de machine op het lichtnet wordt aangesloten, dient gecontroleerd te worden of de machine op het correcte voltage staat A\ De voeding in de monitor blijft warm en er kunnen componenten electrisch geladen blijven ondanks dat de machine

© afgesteld en of de correcte zekeringen zijn aangebracht.

Page 21

Oo FP BP -

Ne Opmerkingen aangaande Installatie

Sluit de machine nooit aan op de stroomtoevoer totdat de installatie is voltooid. mesure Om mogelijke electrische schokken te voorkomen, dient ervoor PSone Meee gezorgd te worden dat de machine middels een goed vastzittende aardstekker op het lichtnet is aangesloten. Om ervoor te zorgen dat klanten niet gewond raken door de a beweging van het spel, dient ervoor gezorgd te worden dat er minimaal 500mm ruimte is tussen andere machines of muren. = a8

Om schade aan de machine door verkeerd gebruik te voorkomen, dient = ervoor gezorgd te worden dat het voltage van het lichtnet 230volts AC BELT bedraagt.

OPMERKING: Als de machine op een gladde ondergrond wordt gebruikt, is het raadzaam rubber matjes onder de stelpootjes te bevestigen om te voorkomen dat de machine over de vioer gaat glijden

OPMERKING: Om toegang te krijgen tot de voeding- en de CPUassemblies, dient ervoor gezorgd te worden dat de achterkant van het kabinet minimaal 500mm verwijderd is van de muur of andere machines.

PRP BRP BP BB Het spel is voorzien van wieltjes, waardoor het gemakkelijker is om te verplaatsen. Wees voorzichtig als de machine op een hellend viak gereden wordt.

Het zwaartepunt van de Header Assembly ligt aan diens voorkant, waardoor het belangrijk is dat minimaal 2 personen de Header Assembly aanbrengen of verwijderen

De Header Assembly moet op een hoge positie geplaatst worden en het is dus belangrijk dat deze hoogte veilig kan worden bereikt zonder veel te strekken. (bijv. middels een trap of een kruk)

De hoogte van het hoofdgedeelte is 1990mm: kijk dus uit voor obstakels zoals lampen.

Als de machine verplaatst of gedragen wordt, dient ervoor gezorgd te worden dat deze in 3 delen wordt afgebroken: Header Assembly, Front Assembly, Ride Assembly

>EP Pe -

> & Verwijderen en vervangen van Assemblies en onderdelen

Installatie, service, aanpassingen of routine-onderhoud dient alleen uitgevoerd te worden door hierin bekwame personen.

Maak geen veranderingen aan deze machine zonder goedkeuring vooraf. Dit kan onvoorzien gevaar opleveren.

Alleen onderdelen die door Namco Europe Ltd. zijn gespecificeerd dienen gebruikt te worden bij het vervangen of repareren van onderdelen (incl. schroeven).

Zorg ervoor dat de machine UlTgeschakeld is voordat er enig onderhoudswerk wordt verricht (troubleshooting, reparaties etc.)

Bij het verrichten van werkzaamheden die niet in deze handleiding staan beschreven, dient voor instructies altijd contact opgenomen te worden met de verdeler aangezien geen verantwoording wordt genomen voor schade of letsel.

Delen van de voeding en de monitor blijven warm of behouden hoogspanning zelfs nadat de machine UlTgeschakeld is en zouden verbrandingen of electrische schokken kunnen veroorzaken. Ben voorzichting en raak deze delen niet per ongeluk aan.

Zorg ervoor dat de machine is UlTgeschakeld voordat pluggen of connectors ingestoken of uitgetrokken worden.

Als het netsnoer uit de machine of uit het stopcontact verwijderd wordt, dient altijd de stekker vastgepakt te worden en niet het snoer. w

Page 22

®) Nenhuma parte desta publicacdo podera ser reproduzida por processos mecanograficos, fotograficos, electronicos ou ainda sob a forma de gravacdo sonora nem téo pouco poder ser gravada através de sistemas informaticos transmissiveis ou de outra forma copiados para uso publico ou privado sem autorizagdo expressa da NAMCO EUROPA LIMITADA.

A informagao contida neste manual foi fornecida de boa fé, sendo rigorosa na altura da sua publicagao. A NAMCO EUROPA LIMITADA, reserva-se o direito de proceder a mudangas e alteragdes sem qualquer aviso prévio Esta maquina foi fabricada de acordo com as Directivas Comunitarias Europeias e tem sido testada em conformidade com as seguintes Directivas: 89/336/EEC e 72/23/EEC através dos requerimentos normativos, EN55014, EN55104 e EN60335-1 (ver capa frontal do manual) e como tal sustenta o certificado de marca de CE. Quaisqueres alteracdes ou modificagdes efectuadas nesta maquina deverao ser em conformidade com as Directivas da Comunidade Europeia. Quaisquer alteragdes nao autorizadas a este equipamento poderdo infrigir tais Directivas.

O funcionamento normal desta maquina, podera ser afectado debaixo de algumas condicées extremas de interferéncias externas tais como; transmissées via radio, descargas electroestaticas e passagens de corrente na rede de alimentacao. Contudo o seu funcionamento normal sera restabelecido logo que a fonte de interferéncias tenha cessado ou tenha sido neutralizada.

Nota :- Se 0 processador de jogo for inicializado devido a uma interrup¢ao ou quebra da corrente principal, quaisqueres creditos obtidos poderao desaparecer.

Este jogo por si so nao contitui uma maquina tal como defenido pelas Directivas de Maquinaria de 89/392/EEC8.

AVISOS DE SEGURANCA Afim de usar esta maquina com seguranga, cettifique-se que Ié este manual de operador atentamente antes de proceder 4 montagem e afinacao ou uso da mesma. Sempre que o proprietario desta maquina confiar a desmontagem, instalagdo, afinag4o ou manutengdo preventiva da mesma a outra pessoa, deverd este assegurar - se que a pessoa em questdo Ié as precaugées apropriadas e capitulos relevantes deste manual antes de iniciar o trabalho. Afim de evitar qualquer tipo de acidente quando a maquina estiver em funcionamento, devera seguir rigorosamente os procedimentos de seguranga descritos abaixo. Este manual juntamente com o manual de instalagdo (aonde aplicavel), contituem parte integrante do equipamento e deverao estar sempre disponiveis ao operador e pessoal tecnico de assisténcia. Esta maquina destina-se a ser operada em espacos interiores apenas e a sua utilizagdo deve circunscrever-se somente aos fins previstos. A Namco Ltd. declina qualquer responsabilidade por acidentes, ferimentos ou danos resultantes de modificagdes nao autorizadas ou uso indevido desta maquina.

AVISOS DE SEGURANCA

Os seguintes avisos de seguranga sao usados através de todo o manual. Familarize-se com cada um destes avisos e respectivos significados antes de instalar, assistir ou efectuar qualquer afinacdo nesta maquina.

PERIGO /\\_ Perigo revela uma situacao anormal que podera resultar em ferimentos ou morte. Nao avance para além de um aviso de Perigo sem que todas as condigées indicadas estejam completamente esclarecidas e resolvidas.

CAUTELA (0) Cautela revela uma situagdo anormal que podera resultar em danos materiais para a maquina. Nao avance para além de um aviso de Cautela sem que todas as condigées indicadas estejam completamente esclarecidas e resolvidas.

AVISOS DE PERIGO

A\ Esta maquina s6 devera ser colocada em funcionamento apés ter sido verificado que se encontra instalada correctamente e de acordo com o manual de instrugées.

> Algumas partes componentes desta maquina movem-se durante a acco de jogo, porconseguinte existem lugares aonde a distancia entre a seccdo fixa e movel altera-se. Existem avisos para manter as mos e os pés afastados da zona de perigo movel, contudo caso o operador se aperceba de alguma pessoa em perigo, devera avisar a mesma em conformidade.

Os avisos de perigo devem ser sempre mantidos em boas condigdes de leitura de forma a permitir uma leitura clara por parte do utilizador, caso se encontrem danificados deverao ser substituidos

Caso esta maquina manifeste algum erro ou problema durante o seu funcionamento, devera ser imediatamente parada até que o problema em questao seja rectificado.

A montagem, assisténcia e afinagdes ou manutengo de rotina desta maquina, deverao ser somente executadas por tecnicos ou pessoas devidamente qualificadas para o efeito.

Afim de garantir uma protegdo anti - fogo permanente nesta maquina, certifique-se que os fusiveis de prote¢do sdo sempre substituidos por fusiveis de igual valor ou calibre aos de origem. O uso de outro tipo de fusiveis ou material é proibido.

A fonte de alimentagao do monitor encontrar-se-a quente, tendo zonas de alta voltagem, mesmo apés a maquina ter sido desligada. Deste facto poder resultar a ocurréncia de queimaduras ou choques electricos. Seja cuidadoso para evitar contacto com estas zonas.

Esta maquina deve estar sempre equipada com uma ficha com circuito de protecgao a Terra, afim de evitar possiveis choques electricos, caso surga uma falha no sistema.

Se a qualquer altura o cabo de alimentagao principal ficar danificado, devera ser imediatamente substituido.

Nao ligar a maquina sem que esta tenha sido correctamente instalada.

Antes de ligar a maquina a tomada da rede de alimentagdo principal, certifique-se de que a maquina esta preparada para a voltagem correspondente e de que também se encontra protegida com os fusiveis apropriados. OPP BP BP BBB B&

Page 23

© PP BB)

NOTAS :

NOTAS :

NOTAS SOBRE A INSTALACAO

NUNCA ligar a maquina sem que a instalacdo esteja completamente finalizada. 7

Afim de evitar possiveis choques electricos, certifique-se que a eed maquina esta ligada a rede de alimentacao com uma ficha protegida com circuito de terra.

Afim de evitar ferimentos pessoais nos clientes, provocados pelo movimento da maquina, certifique-se que existe pelo menos 500mm de separagdo entre outras maquinas ou paredes = ss

Afim de evitar danos na maquina causados por falhas de operagao, - certifique-se que a voltagem da rede de alimentagao principal é de : 230volt AC. |

Se esta maquina estiver colocada sobre um chao polido, recomenda-se

a utilizago de tapetes de borracha debaixo dos pés niveladores, afim

de prevenir a maquina de deslizar no chao.

Quando precisar de aceder a fonte de alimentagao e as placas (CPU), certifique-se que a parte trazeira do movel central esta separada da parede ou de outras maquinas pelo menos 500mm afim de ganhar espago de manobra.

ae a a Co Esta maquina esta equipada com rodas afim de facilitar a sua deslocacao tenha cuidado ao mover a maquina num plano inclinado.

O bloco Superior (Cabega) tem o centro de gravidade para a frente, porconseguinte é importante que pelo menos sejam utilizadas duas pessoas para montar ou desmontar este Bloco Superior.

A posigao do bloco superior quando montado na maquina é muito alta. Torna-se importante ter meios seguros de alcance, tais como; escadotes ou escadas afim de evitar riscos desnecessérios.

A altura total do bloco principal, é de 1990mm, tenha cuidado com qualquer tipo de obstrugdes existentes em altura como por exemplo; calhas electricas ou candeiros.

Ao deslocar ou transportar a maquina, certifique-se que se encontra desmontada em 3 blocos: Bloco Superior, Bloco Frontal, Bloco da Cabine de Condugao ~\

bP BP BBB BP B&

SUBSTITUICAO E MONTAGEM DE PECGAS

A montagem, assisténcia e afinagdes ou manutengao de rotina desta maquina, deverao ser somente executadas por tecnicos ou pessoas devidamente qualificadas para o efeito.

Nao faca qualquer tipo de alteracao prévia nesta maquina sem aprovagao prévia. Se tal acontecer podera provocar danos e perigos imprevisiveis.

A substituigdo ou reparacao de pegas devera ser feita apenas com pegas de origem ou especificadas. pela “Namco Europa Ltd.” (incluindo parafusos)

Certifique-se que a maquina se encontra desligada sempre que iniciar qualquer tipo de trabalho de manutengao. (identifacao de avarias, reparacgao etc.)

Caso esteja a efectuar um trabalho nao descrito neste manual, certifique-se que contacta o seu distribuidor para obter instrugdes, caso contrario nao serao aceites responsabilidades por danos causados ou ferimentos.

Algumas zonas da fonte de alimentagao e do monitor ficam quentes e transportam correntes de alta voltagem, mesmo depois de a maquina ter sido desligada, podendo causar queimaduras e choques electricos. Tome cuidado para nao tocar acidentalmente estas zonas.

Certifique-se que a maquina esta desligada antes de ligar ou desligar qualquer tipo de fichas ou jungées

Quando desligar a ficha principal da maquina ou a ficha do cabo de alimentagao das tomadas da parede, devera sempre agarrar na ficha e nunca puxar pelo cabo da mesma.

Page 24

Ss Ingen del av denna publikation far reproduceras, varken fotografiskt, elektroniskt eller i nagon form av |judinspelning. Det far inte heller lagras i nagot atervinningssystem, dverséndas eller pa annat satt kopieras fér offentlig eller privat anvandning, utan tillstand fran NAMCO EUROPE LIMITED.

Eftersom informationen i denna manual lamnas ut i god tro och var korrekt nar den trycktes, reserverar sig NAMCO EUROPE LIMITED f6r andringar.

Denna maskin har tillverkats enligt direktiv fran europeiska unionen, ar testad och uppfyller direktiven enligt 89/336EEC och 72/23/EEC med tillampning av EN55014, EN55104 och EN60335-1 standard (se manualens framsida) och bar darmed ocksA CE-market. Varje férandring eller modifiering av denna maskin maste ske i dverens-stammelse med EU-direktiven. En férandring i denna produkt, som inte &r auktoriserad, kan strida mot dessa direktiv.

Under vissa omsténdigheter nar det galler extrema externa stdrmingar, t ex radiosdindningar, elektrostatiska urladdningar eller natburna strémstdrningar, kan resultera i en nagot nedsatt funktion. Maskinen kommer dock att aterga till normal funktion, sd snart stérningen har upphért eller avlagsnats

OBS! Om spelprocessorn startar om till {éljd av ett avbrott eller reducering av strémmen kan registrerade krediter gA férlorade.

Detta spel ar inte en maskin enligt definitionen i Maskindirektivet 89/392/EEC

SAKERHETS VARNING

For att maskinen ska kunna anvandas pa ett sakert stt, ska manualen l&sas noggrant fére installation, anvandning eller justering.

Om agaren till maskinen anfértror nagon annan person att montera isar, installera, justera maskinen eller utféra rutinunderhall, ska dgaren férsakra sig om att denna person laser om férsiktighetsatgarder och tillmpliga delar av denna manual innan arbetet pabérjas.

For att frhindra att nagon olycka hander nar maskinen ar igang, maste sakerhetspunkterna beskrivna nedan fdljas strikt.

Denna manual tillsammans med installationsmanualen (nar tillampligt) utgdr en integrerad del av utrustningen och maste vara standigt tillgnglig fdr operatérer och service personal.

Maskinen ar avsedd fér inomhusbruk och ska endast anvandas fér detta andamal.

Namco Ltd. bar inget ansvar for olyckor eller skador som orsakats av icke auktoriserade andringar i maskinen eller felaktigt anvandande av densamma.

SAKERHETSANVISNINGAR

Sakethetsanvisningarna nedan anvands genomgaende i manualen. Gér dig fortrogen med varje anvisning och dess innebérd innan installation, service eller justeringar gérs pa denna maskin.

VARNING A *Varning” anger en fara som skulle kunna skada eller fororsaka dédsfall. Fortsatt inte vid en sadan varningsanvising innan de pavisade férhallandena ar forstadda och atgardade i sin helhet.

OBSERVERA ® "OBSERVERA" anger en fara som skulle kunna férorsaka skada pa maskinen. Fortsatt inte vid en sadan varningsanvising innan de pavisade férhallandena ar férstadda och atgardade i sin helhet.

ALLMANNA SAKERHETSBEAKTANDEN

Satt inte igang maskinen utan att ha kontrollerat att den ar korrekt installerad och i 6verensstammelse med manualen.

Eftersom delar av maskinen rér sig under spel finns det stallen dar avstandet mellan den stationara delen och den rérliga Andras. Det finns varningsanvisningar om att halla hander och fétter borta fran rérliga delar, men skulle operatéren anse att en person ar i nagon som helst fara, ska personen ifraga varnas.

Varningsanvisningarna maste alltid hallas i got skick och ersattas nar de blir slitna, sa att kunderna kan lasa dem dem tydligt.

Om det uppstar fel eller problem med maskinen, maste anvandningen stoppas omedelbart och problemet rattas till innan den ater anvands.

Installation, service, justeringar eller rutinunderhall ska endast utféras av en fér Andamalet kvalificerad person

For kontinuerligt skydd mot brandfara, ska man férsakra sig om att huvudsakringarna endast ersatts med samma typ och specifikationer. Anvandandet av andra sakringar eller material ar férbjuden.

Strémférsérjningen inne i monitorn haller sig varm och har omraden med hég spanning, Aven nar maskinen stangts av och det finns risk for brannskada eller elektriska stdtar. Var forsiktig och vidrér aldrig sadana omraden.

Fr att forhindra en eventuell elektrisk stét fororsakad av fel, MASTE maskinen vara forsedd med sakert ansluten JORDAD kontakt.

Om strémférsérjningskabeln pa nagot satt skadas, maste den bytas ut omedelbart.

Vrid inte stro6mbrytaren till ON innan maskinen ar korrekt installerad. OPP BP BBB BBE BP B&

Innan strémmen sats pa till maskinen, maste man férsakra sig om att den ar installd pa ratt spanning och att ratt sakringar Ar isatta.

Page 25

A A

A

0)

OBSERVERA: Om maskinen ar placerad pa ett polerat golv, recommenderas

OBSERVERA: For att kunna komma at strémf6rsdrjningen och CPU, se till att ATT BEAKTA VID INSTALLATION + as 4 boawereem 0 eee Satt aldrig pa strommen pa maskinen innan installationen 4r klar.

Fér att forhindra elektriska chocker, férsakra dig om att maskinen oo ri kopplas till strémférsérjning med jordad kontakt af

Fér att undvika skador av spelets rérelser, forsakra dig om att det = u5 5 finns ett avstand pa minst 500 mm till annan maskin eller vagg. |

Fér att undvika skador pa maskinen p g a felaktigt handhavande,

forsakra dig om att strémstyrkan Ar 230 volt AC.

att placera gummibrickor under nivajusteringen for att | frhindra att maskinen glider pa golvet.

baksidan av huvudkabinettet ar placerat minst 500 mm fran vagg eller annan maskin.

Spelet ar férsett med hjul fr att underlatta férflyttningar. Var frsiktig om spelet ska flyttas pa en sluttande yta.

Toppskylten har tyngdpunkten framtill, darfér ar det viktigt att minst 2 personer satter dit eller tar bort den.

Toppskyltens placering ar mycket hégt upp och det ar viktigt att sAdana hjalpmedel anvands sa att man nar upp utan att stracka sig (t ex trappstege, pall osv).

Den totala héjden ar 1990mm, tank pa eventuella hégt placerade hinder, t ex lampor.

Om spelet ska flyttas eller baras, kontrollera att spelet ar monterat isar i 3 delar: Toppskylt, Monitorenhet, Spelkontrollenhet

> bP EP PB

> ATT TA BORT ELLER BYTA UT ENHETER OCH DELAR >)

Justeringar och underhall pa denna maskin skall endast utféras av kvalificerad personal.

Gér inga andringar pa denna maskin utan ett godkannande i férvag. Detta kan férorsaka oférutsagbar fara.

Endast delar som ar specificerade av Namco Europe Ltd. ska anvandas vid utbyten eller reparation av delar (inklusive skruvar).

Férsakra dig om att stroémmen 4r avstangd innan underhallsarbete pabérjas (felsékning, reparationer etc.)

Om arbete ska utféras som inte ar beskrivet i denna manual, ar det viktigt att kontakta aterférsaljaren fér instruktioner eftersom inget ansvar accepteras fér averkan eller personskador.

Delar av stromf6érsérjningen och monitorn ar varma och strémbarande aven efter strommen stangts av och kan orsaka brannskador eller elektriska stotar.

Forsakra dig om att maskinen ar avstangd innan kontakter sAatts i eller tas ur.

Nar kontakten tas ur maskinen eller ur vaggen, ta alltid tag i kontakten och inte i sladden. wv

Page 26

Ge)

Tasta julkaisusta ei saa ottaa missdan muodossa kopioita yksityis- tai julkiseen kaytt66n ilman NAMCO EUROPE LIMITED:in lupaa.

TAssa ohjekirjassa olevat tiedot pitavat julkaisuhetkella paikkansa. NAMCO EUROPE LIMITED.:illa on kuitenkin oikeus muutoksiin ilman erillista ilmoitusta.

Tama laite on valmistettu EC direktiivien mukaisesti. Se on testattu ja todettu noudattavan seuraavia direktiivej4: 89/336/EEC ja 72/23/EEC (EN55014, EN55104 ja EN 60335-1 standardit). Nain ollen tama laite on varustettu CE-merkinnailla. Kaikki tahan laitteeseen kohdistetut muutokset on tehtava EC- direktiivien mukaisesti. Mika tahansa valtuuttamattoman huoltomiehen tekema muutos voi olla direktiivien vastainen.

Laitteen toiminta voi hairiintya maaratyissa olosuhteissa, jotka johtuvat 4arimmaisista ulkoisista sahkéhairidista, kuten radiolahetys, elektrostaattinen purkaus tai vahvavirrasta syntynyt hairid. Toiminta normalisoituu kuitenkin heti, kun ulkoinen sAhkéhairié on poistettu.

Huom:- Jos peliprosessori resetoituu sahkékatkoksen tai vastaavan johdosta, voivat kaikki pelivaraukset havita.

Tama laite ei ole 89/392/EEC direktiivien mukainen kone.

Turvallisuusvaroitus

Taman laitteen turvallinen kaytté edellyttéa kayttdohjekirjan huolellista lukemista ennen laitteen asennusta, sdatda tai kayttda.

Jos taman laitteen omistaja antaa jollekin toiselle osapuolelle tehtavaksi purkaa, asentaa, sAatad tai muuten huoltaa laitetta, on omistajan varmistuttava siita, ett toinen osapuoli on lukenut ja ymmértanyt kayttéohjekirjan oleelliset osat ennen tyéhén ryhtymista.

Turvallisuusohjeita on seurattava tarkoin vahinkojen valttamiseksi laitteen ollessa kaytéssa .

Tama ohje seka mahdollinen asennusohje muodostavat laitteiston oleellisen osan ja on siksi aina oltava huolto- ja kayttéhenkildkunnan kaytettavissa.

Tama laite on tarkoitettu vain sisatilakaytté6n. Sita ei saa kayttaa muihin tarkoituksiin.

Namco Ltd ei vastaa niist& onnettomuuksista, loukaantumisista tai vahingoista, jotka johtuvat laitteeseen ilman Namco Ltd:n lupaa tehdyisté muutoksista laitteen vaarasta kaytésta.

Turvallisuusohjeet

Tass kayttdohjekirjassa on kaytetty seuraavia turvallisuuteen liittyvid huomautuksia. Tutustu jokaiseen ndista. Ald asenna, huolla tai s4&da laitteistoa, ennen kuin olet taysin ymmértanyt mit ne tarkoittavat.

VAARA —//\_“Vaara” tarkoittaa uhkaa, joka voi johtaa loukkantumiseen tai kuolemaan, Ala koskaan ohita Vaara-merkintaa, ennenkuin ohjeissa esitetyt olosuhteet on ymmarretty taysin.

VAROITUS © “Varoitus” tarkoittaa uhkaa, joka voi johtaa laitteen vioittumiseen. Ala koskaan ohita Vaara-merkintaa,

YLEISET TURVALLISUUSNAKOKOHDAT

Varmista, etd laite on asennettu oikein ja ohjekirjan mukaisesti ennen kayttddnottoa. >be Laite sisaltaa toimiessaan liikkuvia osia. On paikkoja, jossa liikkuvien osien ja paikalla pysyvien osien valimatka muuttuu. Tallaisissa paikoissa on varoitustaulut, joissa kehotetaan pitamaan kasia ja jalkoja poissa likkkuvista osista. Jos kayttaja on sit mielta, etta joku henkild on vaarassa, on kayttajan velvollisuus varoittaa vaarassa olijaa.

Varoitustaulut on pidettava hyvassa kunnossa. Jos ne ovat kuluneet, ne on ehdottomasti vaihdettava, jotta asiakkaalla olisi mahdollisuus lukea niita selvasti.

Jos laitteeseen tulee vika tai ongelmia, on se pysaytettva valittémasti ja ongelma selvitettava ennen uutta kayttddnottoa.

Vain riittavan ammattipatevyyden omaava henkilé saa suorittaa asennus-, huolto-, saat6- tai muita laitteeseen kohdistuvia rutiinitoimenpiteita.

Jotta palovaaraa ei syntyisi, saa padsulakkeita vaihtaa vain samankokoisiin sulakkeisiin. Muiden sulakkeiden tai materiaalin kaytté on ehdottomasti kielletty. Monitorin sisalla oleva virtalahde pysyy kuumana ja siina on alueita, joissa on korkeajannite vaikka laite on kytketty pois paalta. Palovammojen tai sahkdiskun saaminen on mahdollista. Ald koske naihin alueisiin.

Sahkdiskujen valttamiseksi vikatapauksissa, laite on ehdottomasti kytkettava maadoitetulla johdolla maadoitettuun pistorasiaan.

Vioittunut verkkojohto on valittémasti vaihdettava.

Ala kytke laitetta paalle, ennen kuin se on oikein asennettu. OPP BPBBPB BP BE

Varmista ennen verkkoon kytkemist, etta virtalahteen jannitteen asetus on asetettu oikealle jannitteelle ja etta siina on oikeat sulakkeet.

Page 27

Oo FP EP &

Huomio: Varmista, etta takaosan taakse ja@ vahintaéan 500 mm tilaa, jotta ASENNUSHUOMIOITA

Ala koskaan kytke laitetta paalle ennen kuin asennus on . suoritettu loppuun. + sae ~

Taman laitteen virtalahde on kytkettava maadoitetulla johdolla maadoitettuun pistorasiaan, jotta sahkdiskun vaaraa ei olisi. IT 7 — i Sap zone t Varmista, eta laitteen ja seinan tai toisen laitteen valissa on i vahintaéan 500 mm, jotta asiakkaat eivat loukkaannu laitteen =. 8 likkumisesta johtuen. we] |

Varmista, etta virtalahteen jannite on 230 V AC, jotta ei laite vioitu.

Huomio: Jos tama laite sijoitetaan liukkaalle esim. vahatulle lattialle, suositellaan laitettavaksi kumityynyt saatdjalkoihin liikkumisen + estamiseksi. :

virtalahteeseen ja CPU-korttiin padsee kasiksi.

PRP PB & Laite on varustettu kaantyvilla pydrilla. Tama on pidettava mielessA, kun laitetta siirretaan kaltevalla alustalla.

Yldosan painopiste on ylaosan etuosassa. Tasta syysta on ylaosaa asennettaessa tai poistettaessa oltava vahintaan kaksi henkilda.

Ylaosan asennusasento on erittain korkealla. On tarkeaa, ett tarvittavalle korkeudelle padstaan vaivattomasti ilman venyttamista. (esim. kayta tukevia tuoleja tai tikkaita)

Laitteen kokonaiskorkeus on yli 1990 mm. Varmista, ettei katossa ole esteita. esim. valaisimia.

Kun siirrat tai kannat laitetta varmista, ett laite on purettu neljéan osaan. Yldosa, koottu, Etuosa, koottu, Liikkuva ajo-osa, koottu /

PEP BP BE BP BB B&B

Va ~\ Vain riittavan ammattipatevyyden omaava henkilé saa suorittaa asennus-, huolto-, saaté- tai muita laitteeseen kohdistuvia rutiinitoimenpiteita.

Talle laitteelle ei saa tehda mi vaaroja. an hyvaksymatt6mia muutoksia. Se voi aiheuttaa ennalta-arvaamattomia

Vain Namco Europe Ltd:n maarittelemia varaosia saa kayttaa vaihtaessasi tai korjatessasi osia. (sisaltéen ruuvit).

Varmista, etta laite on kytketty POIS PAALTA ennen tyén aloittamista.

Ota yhteytté maahantuojaan ohjeita varten, jos joudut tekemaan tydtehtavid, joita ei ole esitelty huoltokirjassa, muuten vastuuta vioista tai loukkaantumisista ei ole.

Virtalahde ja monitori pysyvat kuumina ja niissa on alueita, joissa on korkeajannite vaikka laite on kytketty pois paalta. Palovammojen tai sahkdiskun saaminen on mahdollista. Ala koske naihin laitteisiin.

Varmista, ett laite on kytketty POIS PAALTA ennen johtojen kytkemista tai irrottamista.

Irrottaessasi verkkojohdon seinasta tai laitteesta, ota kiinni itse pistokkeesta, ei johdosta.

Page 28

Contents

OPERATORS MANUAL. PORTABLE APPLIANCE TESTING .... GENERAL SAFETY CONSIDERATIONS.. ALLGEMEINE SICHERHEITSHINWEISE . GENERELLE SIKKERHEDSOVERVEJELSER CONSIDERACIONES GENERALES DE SEGURIDAD. CONSIGNES GENERALES DE SECURITE.. E=ETAZH TENIKH2 AX@AAEIAD ................ CONSIDERAZIONI! GENERALI SULLA SICUREZZA VANLIGE SIKKERHETSTILTAK............:0c0ccc0 ALGEMENE VEILIGHEIDSOVERWEGINGEN. AVISOS DE PERIGO .........ceccceseceteteeeeeeeee ALLMANNA SAKERHETSBEAKTANDEN.. YLEISET TURVALLISUUSNAKOKOHDAT.

  • SPECIFICATIONS .29
  • HOW TOPLAY..... -30
  • MAJOR COMPONENTS. -31
  • MOVING THE MACHINE 32
  • INSTALLATION .............. 5-2 Fitting the Header Assembly 5-3 Fitting the Seat Assemblies. 5-4 Adjusting the Level Adjusters .. 5-5 Fitting the Number Decals... 5-6 Linking Two or More Games
  • ADJUSTMENTS ............ 6-1 Turning on the Power 6-2 Adjustment Switches . 6-3 Test Mode ...... 6-3-1 Coin Options 6-3-2 Game Options. 6-3-3 VO Test....... 6-3-3-1 I/O PCB Check... 6-3-3-2 How to [I/F Initialize] 6-3-3-3 Switch Test ..... 6-3-3-4 Camera Check 6-3-3-5 Lamp Test... 6-3-4 Monitor Test . 6-3-5 Sound Tesi 6-3-6 ADS Data 6-3-7 Others ..
  • INITIALIZATIO
  • MAINTENANCE... Replacing the Steering PCB and/or Fuse . Replacing the Fluorescent Lamp or Starter. . Replacing the Camera............. Replacing the Camera Housing .. Replacing the Credit Available / View Change Switch Removing the Steering Wheel ....... Replacing the Steeering Assembly Replacing the Steering Potentiometer Replacing the Drive Belt... 0 Removing the Pedal Assy 1 Replacing the Pedal Potentiometer 2 Replacing the Brake Damper .. Replacing the Pedal Stop Rubb Replacing the Monitor ..
  • PARTS........
  • SCHEMATIC.. DODDDHDODDDDDMDMDH SALA OHNO HKRODHA
Page 29
  • SPECIFICATIONS

POWER SUPPLY:-

AMBIENT OPERATING TEMPERATURE:

MONITOR:-

COIN ACCEPTOR:-

DIMENSIONS:- Assembled

Monitor Cabinet Seat Assembly Header Assembly

WEIGHT:- Assembled

Monitor Cabinet Seat Assembly Header Assembly

ACCESSORIES:- 230v/350watts AC

+5°C to +25°C

Hantarex 28” Polo - Medium Planar (Type 02193240)

Mars CashFlow - 4 Channel Dispense

1600(w) x 1630(d) x 1990(h)

1600(w) x 452(w) x 1470(w) x 870(d) x 1590(h) 820(d) x 1220(h) 450(h) 370(d) x

379kg

302kg 26kg x 2 25kg

Keys: (Cash Door). (Coin Door) (Back Door).

IEC Mains Lead ........ cece 1 Link Cable (HSB 2.9mtr) . Operators Manual Monitor Manual .... CashFlow Documents Race Number Decal (set 1-8) M5 Security Wrench Potentiometer 40°... 1

M6x20 Pozi pan head screw 1"/4” Flat washer M6 Spring washer...

M10 Hex head set screw. M10 Flat washer ..... M10 Spring washer.

Page 30
  • HOW TO PLAY

This is a multi-play car racing game which can be linked to allow up to 8 players to compete on the same course. (2 or more games linked together.)

When 2 or more players are playing, they compete for ranking position, and in

the case of a single player, the player competes against the computer.

[Game Overview] The object of the game is to complete a specified number of laps, or to cover a specified distance in the given time period. Extra time is awarded at specified points of the lap. Players complete the game by crossing the finish line after completing the specified number of laps (or by covering the specified distance) within the given time. If the game has been played by two or more players, the rankings of all players will be announced at the end of the game. The game is over if the time period reaches zero before the specified number of laps (or the specified distance) have been completed.

[To Start a Game] After establishing the correct credit, each player will first select a course to drive. The course is selected by turning the steering wheel and pressing the accelerator pedal to confirm the selection. There are three courses, :-’Mountain Course’, ‘Seaside Course’ and ‘Theme Park Course’. Each player will then select a car to drive from a choice of four cars. The car is selected by turning the steering wheel and pressing the accelerator pedal to confirm the selection. After the first player has established credit, there is a 24 second (adjustable) time period to allow other players to join in before the start of the game. If no other players join in within the 24 seconds the game will be played as a single play mode. After the course and car have been selected by all participating players a picture will be taken of each player and will be displayed above each players car during the game. The picture will be taken automatically after 5 seconds but can be taken immediately by the player pressing the brake pedal.

Page 31
  • MAJOR COMPONENTS

Main unit Assy

y Mains-In Assy (On/Off Switch)

SS23 Rack Assy

Power Supply Assy

Camera JNT ASSY Monitors

Control Panel Assy

Steering wheel Assy

AB Pedal Assy

Coin Box Assy

Seat Assy

Page 32
  • MOVING THE MACHINE

> & This machine is fitted with castors to make it easier to move. Take care when moving the machine on an inclined surface.

The overall height of this machine is 1990mm. Take care of any overhead obstructions. (e.g. Light Fittings, Electric Cables etc.)

uN When moving the game, ensure that the game is dis-assembled into 4

parts: Monitor Cabinet, Header Assembly and Seat Assemblies.

  • INSTALLATION

Notes on Installation

WARNING
WARNING
WARNING
CAUTION NEVER turn the power to the machine ON until installation has been completed.

In order to prevent possible electric shocks, be sure that the machine is connected to the mains with a securely connected earthed plug.

So that customers are not injured , ensure that there is at least 500mm separation between other machines or walls.

In order to avoid damage to the machine due to misoperation, ensure that the voltage of the mains supply is 230volts AC.

NOTE

If the location site of this machine has a polished floor it is

recommended that rubber pads are fitted under the level adjusters to prevent the machine sliding on the floor.

In order to gain access to the Power Supply and CPU assemblies, make sure that the rear of the machine is separated from a wall or other machine by at least 500mm.

When installation is complete, it is imperative that the game is initialized. (See section 7 page 57)

Page 33

This machine is designed for INDOOR USE ONLY. Do not install in the following places.

Outdoors

  • Direct Sunlight, places with excessive humidity or dust, places where there is water leakage, near air-conditioning or heating equipment, places with excessive heat or cold temperature.
  • Places where it would be in the way of emergency exits or fire extinguishing equipment. Unstable places or places with excessive vibration. Places that are not level.
  • This machine must not be cleaned with a water jet, or installed in an area where a water jet could be used. as

@) DIESES GERAT IST NUR FUR DIE GEWERBLICHE AUFSTELLUNG IN

GESCHLOSSENEN RAUMEN BESTIMMT. DAS GERAT DARF AN FOLGENDEN PLATZEN NICHT AUFGESTELLT WERDEN

  • Im Freien.
  • In direktem Sonnenschein, an extrem feuchten und staubigen Platzen, an Platzen mit Wasseranschliissen und méglichen Leckagen, nahe Klima- und Heizungsanlagen, an Platzen mit extrem hohen oder niedrigen Temperaturen.
  • In der Nahe von Notausgangen oder Feuerldschgeraten.
  • An unstabilen Platzen oder Platzen mit UbermaBiger Vibration.
  • An Platzen, die nicht eben sind.

(OK) DENNE MASKINE ER KUN DESIGNET TIL INDENDORSBRUG

INSTALLER IKKE MASKINEN PA F@LGENDE STEDER

Udendors

  • Direkte sollys, steder med hgj fugtighed el. stov, steder med vand udslip, i nzerheden af air-condition eller varme udstyr, steder med uszedvanlig hoj el. kold temperatur. Steder hvor den vil sta i vejen for nodudgange eller brandslukningsudstyr. Ustabile steder eller steder med for store vibrationer. Steder der ikke er plane. apo

ESTA MAQUINA ESTA DISENADA UNICAMENTE PARA USO EN INTERIORES. NO INSTALE LA MAQUINA EN LOS SIGUIENTES LUGARES.

Exteriores.

  • Bajo luz solar directa, en lugares con polvo o humedad excesiva, lugares donde hay filtraciones de agua, cerca de aparatos de calefaccion o de aire acondicionado, lugares con temperatura ambiente muy alta o muy baja.
  • Lugares donde la maquina obstruya salidas de emergencia 0 equipos de extincion de incendios. Suelos inestables o lugares con vibraciones excesivas. Lugares con suelos no nivelados. as
Page 34

PO

pam od A

CETTE MACHINE EST DESTINEE UNIQUEMENT A UN USAGE INTERIEUR NE PAS INSTALLER LA MACHINE DANS LES ENDROITS SUIVANTS

A l’extérieur. Directement exposée au soleil, aux endroits excessivement humides ou poussiéreux, aux endroits ou il y ades risques de fuite d’eau, prés de ventilateurs ou source de chaleur, aux endroits trés chauds ou froids. Dans des zones de proximité des sorties de secours ou d’accés aux équipements d’extinction du feu. Dans des emplacements instables ou soumis a de fortes vibrations. Dans des endroits dénivelés.

TO MHXANHMA EINAI LXEAIAZMENO IIA XPHEH LE ELQTEPIKO XQPO MONO MHN TOMOOETHZIETE TO MHXANHMA XTOYE AKOAOYOOYE XQPOYE

Efortepixa Azev0eiac otov 210,68 pépy 6200 vadpyer vypacia } oKévy,pépy 6z0v vTAPYE1 GQVOVO vep6,KovTa 6 air-condition } G.A00 cidouc Oéppavon,pépy pe vtepPokiKy vyyAY H YanHAY OeppoKpacia. Le pépy 6z0v eprodiCovv péca avayKys 7.y. TvpooPectipess H GAXG. My otabepa pépy h pépy pe 70Ad00¢ Kpadacpotc. Mépy ov dev sivan exineda.

QUESTA MACCHINA E’ PROGETTATA PER ESSERE USATA ESCLUSIVAMENTE IN AMBIENTI INTERNI. NON INSTALLARE LA MACCHINA NEI SEGUENTI LUOGHI.

In ambienti esterni. Alla luce diretta del sole, in posti con eccesiva umidita o polvere, in luoghi dove ci siano infiltrazioni d’acqua, vicino ad apparecchi di condizionamento d’aria oppure riscaldamento, in posti eccessivamente caldi 0 freddi. In luoghi dove potrebbe esserci un uscita di emergenza 0 un’attrezzatura per lo spegnimento del fuoco. In posti non stabili o con eccessive vibrazioni. In luoghi non piani.

DENNE MASKINEN ER BARE KONSTRUERT FOR INNENDORS BRUK IKKE INSTALLER MASKINEN PA FOLGENDE PLASSER.

Utendors Konstant sollys, plasser med mye fuktighet og stov, plasser hvor det er vannlekasje, neere luft kjolere eller varme elementer, plasser med overdreven hoy eller lav temperatur. Plasser hvor det vill stai veien for nodutganger eller brannslukking utstyr. Ustabile plasser eller plasser med overdreven vibrasjon. Plasser som ikke er i vater.

DEZE MACHINE IS ALLEEN VOOR GEBRUIK BINNENSHUIS ONTWORPEN INSTALLEER DE MACHINE NIET OP DE VOLGENDE PLAATSEN

Buiten In direct zonlicht, op plaatsen met een zeer hoge vochtigheidsgraad of met veel stof, op plaatsen waar een waterlek is, dichtbij airco’s of verwarmingsapparatuur, op plaatsen met een zeer hoge of koude temperatuur. Op plaatsen waar nooduitgangen of blusapparatuur worden geblokkeerd. Op onstabiele plaatsen of plaatsen waar grote trillingen voorkomen. Op plaatsen die niet viak zijn.

Page 35

®

as

® A

ESTA MAQUINA FOI CONCEBIDA PARA UTILIZACAO EM ESPACOS INTERIORES APENAS NAO INSTALAR A MAQUINAS NOS SEGUINTES LOCAIS:-

Exteriores. “Luz solar directa, locais com humidade excessiva ou pd, locais aonde existam fugas de agua perto de ar condicionados ou equipamentos calorificos e locais com temperaturas excessivamente quentes ou frias. Locais aonde ficaria colocada no caminho de saidas de emergéncia ou equipamentos extintores de fogo. Locais estruturalmente instaveis ou locais com vibrag6es excessivas. Locais nao nivelados.

DENNA MASKIN AR AVSEDD ENBART FOR INOMHUSBRUK INSTALLERA EJ MASKINEN PA FOLJANDE STALLEN

Utomhus | direkt solsken, platser med extremt hég luftfuktighet eller damm, platser dar det férekommer vattenlackage, nara luftkonditionering eller varmeelement, i extremt hég eller lag temperatur. Platser dar den skulle kunna vara i vagen fér nédutgangar och brandslackningsutrustning. Instabila stallen eller dar stark vibration f6rekommer. Platser med nivaskillnad.

TAMA LAITE ON SUUNNITELTU VAIN SISAKAYTTOON ALA ASENNA LAITETTA SEURAAVIIN PAIKKOIHIN:

Ulkotilaan Suoraan aurinkovaloon, kosteisiin tai pdlyisiin paikkoihin, vesivuotopaikkojen laheisyyteen, ilmanvaihto- tai lammityslaitteen lahistdlle tai paikkoihin, jossa on erittain kuumaa tai kylmaa. Varauloskaytavien, muiden pakoteiden tai tulensammutusvalineiden eteen. Epavakaisiin tai tariseviin paikkoihin. Kaltevalle alustalle.

Page 36

5-2 Fitting the Header Assembly

The Header Assembly has a forward centre of gravity, so it is important that at least two people are used to fit or remove the Header Assembly.

The fitting position of the Header Assembly is very high, and it is important that a means of reaching the height safely , without stretching, is available (e.g. steps, step stool etc.)

  • Place the Header Assembly on to the top of the Monitor Cabinet and connect the connector.

Header Assy

Connector

  • Slide the Header Assembly forward, taking care not to trap any wires, so that it fully engages under the retaining brackets.
  • Fit the 30ff pozi head screw, with flat and spring washer, (M6x20) to retain the Header Assembly in position.

Pozi Head Screw (with flat and spring washer) M6x20

Header Assy

Page 37

5-3 Fitting the Seat Assemblies

  • Remove 10off security screw (M5x16) and remove both floor plates.

Security Screw (M5x16)

Floor-plate (R)

  • Place the Seat Assemblies up to the Monitor Cabinet and set the adjustable feet so that the seat base is level with the main cabinet.
  • Connect the connectors.
  • Fit the 80ff Hex head screws (M8x25), 4 screws per seat, with flat and spring washers to retain the Seat Assemblies in position.

Hex Head Screw (M8x25)

  • Refit the floor plates with the 10off security screws (M5x16).
Page 38

5-4 Adjusting the Level Adjusters

  • When the assembled game is in its final position, lower the twelve (12) level adjusters,(4off Monitor Assy and 4off each Seat Assy), with a spanner so that the machine is level and all castors are raised from the floor by approx. 5mm. Tighten the lock nuts with a spanner to ensure that the level adjusters do not move.

Level Adjuster y castor

Note: If the location site of this machine has a polished floor it is recommended that rubber pads are fitted under the level adjusters to prevent the machine sliding on the floor when in use.

5-5 Fitting the Number Decals

  • Fit the self adhesive number decals to the rear of each seat with the left seat, viewed from the rear of the seat, as No1 and the right seat as No.2. (See Section 6-3-2 page 46 to set the game PCB ID correctly)

Numbered label

Numbered label

  • If linking 2 or more cabinets, the numbering should continue consecutively from left to right. (viewed from the rear of the seat)
Page 39

2 Games Linked

Numbered label 2, Numbered label

3 Games Linked

Numbered label

Numbered label Gog

4 label

oO label Numbered label

4 Games LinkedZ

Page 40

5-6 Linking Two or More Games

  • Remove 2off pozi head screws (M5x12) and remove the Link Cover Bracket.

Pozi Head Screw (M5x12)

  • Fit the Link Cable (supplied) as shown in the following diagram.

Linking Two Games

Main Unit Assy (1) Main Unit Assy (2)

ct) OD (oo i

Attached Communication Cable

  • Refit the Link Cover Bracket with the 2off pozi head screws (M5x12).
  • See section 6-3-2 page 46 to set the game PCB ID. Failure to set the ID will prevent the games operating correctly.
Page 41

Linking Three Games

Main Unit Assy (1) Main Unit Assy (2) Main Unit Assy (3)

Attached Communication Cable Attached Communication Cable

Linking Four Games

Main Unit Assy (1) Main Unit Assy (2) Main Unit Assy (3) Main Unit Assy (4)

Attached Attached Attached

Communication Cable Communication Cable Communication Cable

Page 42
  • ADJUSTMENTS

@

6 © 0680660 6 @ @ A

Adjustment or maintenance on this machine should be carried out by qualified personnel only.

Einstellungen und Wartung des Gerates dirfen nur von dafir qualifiziertem Fachpersonal vorgenommen werden.

Justeringer eller vedligehold af denne maskine bor kun udfores af kvalificeret personale.

Los ajustes y el mantenimiento de esta maquina deben ser realizados sOlo por personal cualificado.

L’installation, le service, le réglage, ou la maintenance doivent étre effectués uniquement par les personnes qualifiées.

Metatponécs 1 extd10p0doeic ota pyyavipata mpérer va yivovtat povo and e§ovorodsotynpéva Gtopa.

Regolazioni e manutenzione su questa macchina devono essere fatti solo da personale specializzato.

Justering eller vedlikehold pa denne maskinen skall bare utfores av kvalifiserte personell.

Aanpassingen of onderhoud aan deze machine dient alleen uitgevoerd te worden door bekwaam personeel.

Afinagées ou manutengao nesta maquina, deverdao ser efectuadas sOmente por pessoal qualificado.

Justeringar och underhall pa denna maskin skall endast utféras av kvalificerad personal.

Tata laitetta saa saataa tai huoltaa vain siihen ammattipatevyyden omaava henkilékunta.

6-1 Turning on the Power

After the machine has been installed, turn ON the power. The power switch is located on the rear of the monitor cabinet.

Page 43

6-2 Adjustment Switches

The Adjustment switches are located inside the coin door.

1. Service Switch. Press this switch to obtain game credits without incrementing the play meter.

Test Switch Slide the test switch ON to enter test mode. Test mode allows testing and the changing of game settings. (Refer to section 6-3 "Test Mode" page 44)

Select Up/Down Switch This switch is used to select the test required when in the Test Mode.

Enter Switch This switch is used to enter a selected test and to change settings within a test.

COIN COUNTER a 2 Amp Q/B (Coin Fuse) : O

PLAYER 1 PLAYER 2

UP UP @| SELECT SELECT|® DOWN DOWN

O *" Oo *o*

TEST SERVICE TEST SERVICE

Page 44

6-3 Test Mode

  • Open the coin door and slide the test switch “ON”. The “Menu Screen’ will be displayed on the monitor.
  • Select the test required by using the select up/down switch. The colour of the selected test will change.
  • Activate the test by pressing the Enter switch. Select “EXIT” in each test to return to the “Menu Screen’.
  • After testing is completed, slide the test switch to the “OFF” position to return to normal game mode.

The Test Switch must always be in the “OFF” position for normal game mode.

(— >) MENU

COIN OPTIONS. .....ceccceceseetssseseseeneeesesesteeeens Used to set the price of play.

GAME OPTIONS .....cecceeseseesesseseetesseeseeeeeeeeees Used to set the game options.

VO TEST .| Used for testing switches, lamps and camera. MONITOR TEST sisssiscsiscssscisesnssrscrsavesssvenasoancaied Used for setting the monitor.

SOUND TEST crsseresnarecssniecnsassessscemaseeanavsd Used for setting the volume.

ADS DATA secscssessssseseeeseesesseeseseeseseesseseeeeee Used to view bookkeeping.

OTHERS —— i reeceececssseseseeestsessesesteasessesseeeees Used for testing the PCB.

.| Only displayed when the battery is faulty (Refer to your Distributor). The internal battery’s dead..

(| SELECT SW:CHOOSE ENTER SW: ENTER)

Page 45

6-3-1 Coin Options

  • Select “COIN OPTIONS” on the menu screen to set the game cost and related settings. The following screen is displayed.
  • Use the Select Up/Down switch choose the required item then press the Enter button.
  • Use the Select Up/Down switch to change the setting.
  • Select “EXIT” and press the Enter button to return to the menu screen.
Note:- The price of play on this machine is set within the Cashflow Coin Mech. Ensure that the Game Cost is set to 1 Coin 1 Credit.

(— > COIN OPTIONS <DEFAULT IN GREEN>

GAME COST (1P) 1 COIN (S) 1 CREDIT .......pocceeee (a)

FREE PLAY OFF aun venened eaxsossnaneneny (b)

EXIT

SELECT SW :CHOOSE ENTER SW : ENTER

N J

Item Description Default

  • Game Cost |Coins required for number of credits ---- settable 1~9 1 Coin 1 Credit
  • Free Play No coins required for credit ---- On (Yes) / Off (No) OFF
Page 46

6-3-2 Game Options

  • Select “GAME OPTIONS” on the menu screen to set the game variables, the following screen is displayed.
  • Use the Select Up/Down switch to choose the required item then press the Enter button.
  • Use the to Select Up/Down switch to change the setting.
  • Select “EXIT” and press the Enter button to return to the menu screen.

( »

GAME OPTIONS [1/2] [DEFAULT IN GREEN]

PCB ID. RED 1 LINKON O04 +1

Ne ENTRY WAIT 20 SEC LAPS

MOUNTAIN 4 LAPS MOUNTAIN C (MEDIUM)

THEME PARK 3 LAPS GAME TIME (LINK)

MOUNTAIN C (MEDIUM)

SEA SIDE C (MEDIUM) THEME PARK C (MEDIUM) GAME TIME (SOLO)

SEA SIDE C (MEDIUM) THEME PARK C (MEDIUM) BROADCAST ON

NEXT PAGE EXIT

SELECT SW: CHOOSE ENTER SW: ENTER Ne y,

( >)

GAME OPTIONS [2 / 2] [DEFAULT IN GREEN]

SPEED DISPLAY MPH

SYCHRONIZE ON

HI-SCORE INIT

NEXT PAGE EXIT

SELECT SW: CHOOSE ENTER SW: ENTER zo S

Page 47

Item Description Default

ay RED1, GREEN2, YELLOW3, BLACK4, RED1

  • Sats player position D REDS, GREEN6, YELLOW7, BLACK8 | GREEN2 b Time in seconds for other players . 20 to join game before game start.

0) number of laps for Mountain settable 2-8 4

Number of laps for Theme Park

d Course.settable 2~83
Game time for Mountain Course:.
©) in linked modeA (), B (), C (Medium), D (), E()C (Medium)
Game time for Sea Side Course..
f) in linked modeA (), B (), C (Medium), D (), E()C (Medium)
Game time for Theme Park in..
g linked modeA (), B (), C (Medium), D (), E()C (Medium)
e came time for Mountain Coursea |)(),C (Medium), D (),E(C (Medium)

iy Game time for Sea Side Course | 0, B,C (Medium), D 0), £0 © (Medium)

Game time for Theme Park in..
(g solo modeA (), B (), C (Medium), D (), E()C (Medium)
h) Commentary during the gameOFF / ONON
i) Sets speed displayMPH or km/hMPH
0)OFF / ONON
(k) Hi-Score initialized at power-up|YES / NONO
Page 48

6-3-3 I/O Test

  • Select “I/O TEST” on the menu screen to test the switches and lamps. The following screen is displayed.
  • Use the Select Up/Down switch to choose the required item then press the Enter button to enter the test.
  • Select “EXIT” and press the Enter button to return to the menu screen.

(— > VO TEST

DIP 4 = 12845678 [ON:RED] —eessscsssssssssesessssssssefessesseseseeneees (a) LINK ON O4FT ————aansvinespavavesinnasaiiese] eesarencesisasens (b)

VO PCB CHECK —i hascecssesesesetestsstsesfecseesesseeeenes(c)
HOW TO [I/F] INITIALIZEceeececeeeeeeeeeseeeeeeeeeseesseeteneeeee(d)

SWITCH TEST (e)

LAMP TEST=—«—-—-—__taataneczeensanasnnavanncan|vegtseseaenssenn(f)
CAMERA CHECK —ll eaeeeccsesesetestsstetseate[essstseeteneeree(g)

EXIT

SELECT SW: CHOOSE ENTER SW: ENTER XN S

  • Shows the condition of the DIP Switches on the PCB. In normal operation all switches are OFF. (If a switch is ON, it will be displayed in red.)
  • Shows how many players are linked and condition of link.
  • Checks function of I/O PCB.
  • Initialize game potentiometers. (see Section 7 page 57)
  • Selecting this item allows all switches to be checked. (See 6-3-3-3 page 50)
  • Selecting this item allows the testing of the lamps. (See 6-3-3-5 page 53)
  • Selecting this item allows the testing and setting of the camera. (See 6-3-3-4 page 51)
Page 49

6-3-3-1 I/O PCB Check

  • Select ‘I/O PCB CHECK’ from the I/O Test Screen. The following screen is displayed:-

( > VO TEST

DIP 4 12345678 [ON=RED] LINK ON2

1/0 PCB CHECK

master TX 3536 NAMCO LTD. RACE ON! ; Ver 1.00 ; JPN

1/0 PCB CONNECT OK NAMCO LTD.

ASCA-4

EXIT

Ne /

Note: This screen is for information only. No adjustments are available.

6-3-3-2 How to [I/F Initialize]

Select ‘How to [I/F Initialize]’ from the I/O Test menu. The following screen is displayed.

(— > VO TEST DIP 4 12345678 [ON=RED] LINK ON2

HOW TO [I / F INITIALIZE]

  • 1/7 F INITIALIZE *
  • HOLDING SERVICE SW *
  • AND TURN ON TEST SW * ee es

EXIT

Ne S

Note: Initialization cannot be executed from this screen. (see 7 page 57)
Page 50

6-3-3-3 Switch Test

  • Select “Switch Test” on the I/O menu screen to test the switches. The following screen is displayed.
  • The display shows the current state of the switches.
  • Press the Up Select switch and the Enter switch together to EXIT and return to the I/O menu screen

( VO TEST »

DIP 4 123456787 [ON/RED]

SWITCH TEST COIN 0 SERVICE OFF TEST ON UP SELECT OFF DOWN SELECT OFF ENTER OFF

HANDLE +0000 RIGHT OK GAS 0000 BRAKE 0000 VIEW CHANGE

EXIT UP SELECT SW + ENTER SW )

  • Not Used

(b to f) Display will change from OFF to ON each time a switch is operated.

  • Numbers increase when the steering is turned to the right and decrease when turned to the left. Right OK and Left OK is diplayed just before the steering wheel is turned to its full extent. Centre is displayed when the steering wheel is in the central position.
  • Numbers increase when the accelerator pedal is pressed, and OK is displayed just before the pedal reaches its full travel.
  • Numbers increase when the brake pedal is pressed, and OK is displayed just before the pedal reaches its full travel.
  • The display will change from OFF to ON each time the switch is operated.

Note: If Left OK or Right OK is not displayed when the steering is

turned or OK is not displayed when the pedals are pressed reinitialize the game. (see 7 page 57)

Page 51

6-3-3-4 Camera Check

1. Select ‘CAMERA CHECK’ from the I/O Test Screen. The following screen is displayed:-

\_ SELECT SW:CHOOSE ENTER SW: ENTER /) ~ VO TEST

CAMERA CHECK [DEFAULT IN GREEN]

MIRROR . (a) IRIS ADJUST DIII MII 18 - (b)

TINT ADJUSTGIMPPRo ee (c)
V POSITION4000raneeeesssssseecfesssseeneeseceessees (d)
H POSITION4000eaneeeesssssseecfesssseeteescceesseee (e)

EXIT

TAKE A PHOTO AND RELEASE : BRAKE OR SERVICE SW

In the CAMERA CHECK Screen, the current view of the camera is displayed in the centre box.

MIRROR/PHOTO By pressing the Brake Pedal or Service Switch, the image from the camera is frozen on the screen and the word MIRROR, just below the image box, changes to PHOTO. This is the mage that would be used during the game. Pressing the Brake Pedal or Service Switch again reverts back to current camera image, and the word PHOTO changes to MIRROR. The mode of [MIRROR] is used for adjustment of the image, and the mode of [PHOTO] to verify the picture to be used during the game.

IRIS ADJUST This setting is used to adjust the brightness of the image. The brightness of the image is automatically adjusted to the optimum value by the system, but this item allows the brightness level to be set manually. Select this item and press the ENTER button. Use the Select UP/ DOWN switch to make the image brighter or darker. There are three brighter and three darker settings available. Press the ENTER button to store the new setting and to exit this mode.

Page 52
  • TINT ADUST This setting is used to adjust the colour tint of the image. The colour tint of the image is automatically adjusted to the optimum value by the system, but this item allows the colour tint level to be set manually. Select this item and press the ENTER button. Use the Select UP/DOWN switch to increase or decrease the red tint. The red tint can be increased or decreased by three levels each. Press the ENTER button to store the new setting and to exit this mode.
  • V POSITION This setting is used to set the vertical position of the camera view. Select this item and press the ENTER button. Use the Select UP/DOWN switch to move the camera view up or down. Press the ENTER button to store the new setting and to exit this mode.
  • H POSITION This setting is used to set the horizontal position of the camera view. Select this item and press the ENTER button. Use the Select UP/DOWN switch to move the camera view left or right. Press the ENTER button to store the new setting and to exit this mode.

° Select EXIT and press the Select Button to return to the I/O Test Screen.

Adjustment of the Camera

Adjust the camera to obtain the best image by following the steps below.

  • Verify moving images. Make sure that the image in the test screen box is moving. If a still picture is shown press the Brake Pedal once.
  • Adjust the image quality. Check the brightness and colour tint of the image and if neccessary adjust by following steps (b) and (c) above.
  • Adjust the position. Make any adjustments neccessary by following steps (d) and (e) above. To set the position for the average height try to set the position of the camera as shown below.

Facial picture frame

Seat speakers

  • Check the image. Sit in the seat and step om the Brake Pedal. Check the quality and position of the still image. If the image is not correct, step on the Brake Pedal and follow repeat steps 2 and 3 above.
Page 53

6-3-3-5 Lamp Test

  • Select ‘LAMP TEST’ from the I/O Test Screen. The following screen is displayed:-

Va VO TEST

DIP 4 12345678 [ON:RED] LINK ON 04+1

LAMP TEST VIEW CHANGE OFF lo haeseesesseseeeses EXIT

SELECT SW: CHOOSE ENTER SW: ENTER ~

/

  • The View Change lamp will turn On or OFF each time the Enter switch is pressed, and the display will change from OFF to ON.

6-3-4 Monitor Test

1. Select “MONITOR TEST” on the menu screen to test and adjust the Monitor. The following screen is displayed.

Use the Select Up/Down switch to choose the required item then press

the Enter button. To return to the Monitor Test Menu from a test pattern

press the Enter button.

Select “EXIT” and press the Enter button to return to the menu screen.

ya MONITOR TEST

GRADATION PATTERN CROSSHATCH PATTERN (CRT) CROSSHATCH PATTERN (PROJ) WHITE WINDOW (H) WHITE WINDOW (M) WHITE WINDOW (L) INTERLACE PATTERN VIEW ANGLE ADJUST (CRT) VIEW ANGLE ADJUST (PROJ) FULL WHITE EXIT SELECT SW : CHOOSE ENTER SW: ENTER ~

S

Note: Items (c) and (i) are not used on this game.
Page 54

6-3-5 Sound Test

  • Select “SOUND TEST” on the menu screen to test the audio and adjust the volume settings. The following screen is displayed.
  • Use the Select Up/Down switch to choose the required item then press the Enter button.
  • Use the Up/Down switch to change the setting.
  • Press the Enter button to return to item select mode
  • Select “EXIT” and press the Enter button to return to the menu screen.

SOUND TEST

<DEFAULT IN GREEN> GAME VOLUME AUTO SETTING FRONT L&R SP

FRONTL SP(0~64)
FRONTR SP(0-64)

REAR L&@R SP

REARL SP(0~64)
REARR SP(0-64)

ATTRACT VOLUME AUTO SETTING FRONT L&R SP (0~64) REAR L&R SP (0~64)

EXIT

REQUEST : SERVICE SW XN REQUEST SONG NO. 0000...

MESSAGE : \

ENTER : ENTER SW CHOOSE : SELECT SWITCH

yy,

Page 55

AUTO SETTING The volume levels of all speakers will be adjusted at the same time with the balance between front and rear speakers being set automatically.

RONT L&R SP he volume levels for both front speakers will be adjusted together.

RONTLSP [0~64, DEFAULT = 40] he volume level for the front left speaker only will be adjusted. san

FRONT R SP [0~64, DEFAULT = 40] The volume level for the front right speaker only will be adjusted.

REAR L&R SP The volume levels for both rear speakers will be adjusted together.

REARLSP [0~64, DEFAULT = 30] The volume level for the rear left speaker only will be adjusted.

REAR RSP [0~64, DEFAULT = 30] The volume level for the rear right speaker only will be adjusted.

AUTO SETTING The volume levels of all speakers, during attract mode, will be adjusted at the same time with the balance between front and rear speakers being set automatically.

RONT L&R SP [0~64, DEFAULT = 40] he volume levels of both front speakers, during attract mode, will be adjusted together. An

REAR L&R SP [0~64, DEFAULT = 30] The volume levels of both rear speakers, during attract mode, will be adjusted together.

REQUEST SONG No.

Each number produces a different sound each time the service

button is pressed. (The sound will turn off after approx 10 seconds)

Number 001 will produce a stereo test. Sound will be produced from the left speaker then the right speaker and then both speakers, first from the cabinet speakers and then from the seat speakers. The message on the screen will display which speaker is active.

Page 56

6-3-6 ADS Data

By selecting ADS Data from the menu screen, all of the bookkeeping details can be read and/or reset.

6-3-7 Others

Select “OTHERS” on the menu screen. The following screen is displayed.

  • Use the Select Up/Down switch choose the required item then press the Enter button.
  • Select “EXIT” and press the Enter button to return to the menu screen.

( OTHERS >)

ROM1 Ver.97/07/07MON21:15:59epee (a)
ROM2 Ver.97/06/27FRI20:11:35
CLOCK97/08/27WED28111112eeepc (b)

PCB TEST LANGUAGE ENGLISH BACKUP MEMORY INITIALIZE

EXIT

SELECT SW : CHOOSE \ ENTER SW : ENTER )

(a,) Displays game software version.

  • The current time is displayed (the time cannot be reset)
  • Used to test the PCB. (this function is only for factory testing)
  • Sets the language displayed on the screen. (English:ENG, German:GER, French:FRA, Spanish:SPA, Portugese:POR, Italian ITA)

When selected the Data Initialization Menu appears. To reset all game settings to factory setting and clear all stored data , select YES from the Data Initialization menu then press the Enter button.

After initializing the backup data ensure that the game is reinitialized. (see section 7 page 57)

Page 57
  • INITIALIZATION

Adjustments when Replacing Parts

The following operation must always be performed after replacing the Game PCB, Rom, or Control Potentiometers. The game will not operate correctly if these adjustments are not made.

  • Slide the TEST switch ON while pressing the SERVICE switch . The following screen is displayed.

(— >) VF INITIALIZE

HANDLE +0000

GAS 0000

BRAKE 0000

GO TO [SWITCH TEST] : ENTER EXIT : DOWN TEST SW

N w

  • Ensure that the steering wheel is set to its centre position and both the accelerator and brake pedals are released.
  • Press the Service Switch to reset the the numbers displayed on the screen.
  • Turn the steering wheel fully to the left and then the right.
  • Fully depress and release the accelerator and brake pedals.
  • Press the Enter Switch to store the new limits and to go to Switch Test to confirm that the steering and pedal controls are working correctly.
Page 58
  • MAINTENANCE

A

@ Adjustment or maintenance on this machine should be carried out by qualified personnel only. Ensure that the POWER to the machine is turned OFF before commencing any maintenance work. (Trouble shooting, service or repairs etc.)

® Einstellungen und Wartung des Gerates dirfen nur von dafir qualifiziertem Fachpersonal vorgenommen werden. Vor Beginn aller Wartungsarbeiten (Fehlersuche, Reparaturen etc.) muB der Netzstecker gezogen werden.

&® Justeringer eller vedligehold af denne maskine bor kun udfores af

kvalificeret personale. Sorg for, at strommen til maskinen er slukket for der foretages nogen form for arbejde (fejlfinding, reparation etc.)

© Los ajustes y el mantenimiento de esta maquina deben ser realizados sOlo por personal cualificado. Asegtrese de que la maquina esta desconectada antes de comenzar cualquier trabajo de mantenimiento (reparaciones, resoluci6n de problemas, etc.)

® L’installation, le service, le réglage, ou la maintenance doivent étre effectués uniquement par les personnes qualifiées. S’assurer que l’interrupteur soit sor OFF avant de commencer tout travail de maintenance (localisation d’une panne, réparations, etc.)

@ Metatponés i extd10p0doeic ota pyHyYavipata mpéreEr va yivovtat povo and e§ovorodsotypéva atona. Na eivar ciyoupa KAEloT6 To peta mpi omoladymote SovdELa OTO WHZGVHPG.

@® Regolazioni e manutenzione su questa macchina devono essere fatti solo da personale specializzato. Assicurarsi che la macchina sia SPENTA prima di incominciare qualsiasi lavoro di manutenzione (guasti, riparazioni etc.)

@ Justering eller vedlikehold pa denne maskinen skall bare utfores av kvalifiserte personell. Forsikre deg om at strommen er slatt av for du pabegynner noe som helst vedlikeholdsarbeid (feilsoking, reparasjon osv.)

Page 59

@ Aanpassingen of onderhoud aan deze machine dient alleen uitgevoerd te worden door bekwaam personeel. Zorg ervoor dat de machine UlTgeschakeld is voordat er enig onderhoudswerk wordt verricht (troubleshooting, reparaties etc.)

® Afinagées ou manutencgao nesta maquina, deverao ser efectuadas sOmente por pessoal qualificado. Certifique-se que a maquina se encontra desligada sempre que iniciar qualquer tipo de trabalho de manutengao. (identifagao de avarias, reparagao etc.)

© Justeringar och underhall pa denna maskin skall endast utféras av kvalificerad personal. Forsakra dig om att str6mmen ar avstangd innan underhdllsarbete pabérjas (felsékning, reparationer etc.)

@ Tata laitetta saa saataa tai huoltaa vain siihen ammattipatevyyden omaava henkilékunta. Varmista, etta laite on kytketty POIS PAALTA ennen ty6n aloittamista.

Page 60

8-1 Replacing the Steering PCB and/or Fuse

1. Remove 2off security screw (M5x12) and lower the steering PCB tray.

Fuse 3A Q/B

Steering PCB

Security screws (M5x12)

Replace the fuse.

OR

Disconnect the connectors.

Replace the steering PCB.

Raise the steering PCB door and refit the 2off security screw (M5x12).

Page 61

8-2 Replacing the Fluorescent Lamp or Starter.

1.

2.

3.

4. Remove 3off security screw (M5x12) and remove the top retaining bracket.

Remove the Header Acrylic.

Security screw (M5x12) Top retaining bracket

Header acrylic

Replace the Fluorescent tube or starter.

Reassemble in reverse order.

Page 62

8-3 Replacing the Camera

  • Remove 4off security screw (M5x20) and remove the Camera Joint Assy.

Connector Camera Joint Assy ‘

Security Screw (M5x20)

  • Disconnect the connector.
  • Remove 1off pozi head screw retaining the cable clamp.
  • Remove the Camera PCB Assy from the Camera Joint Assy by gently pulling the retaining tab to the right to release the PCB .

Cable Tie

Retaining Tab

Pozihead Screw Zz “Camera PCB

  • Replace the Camera PCB Assy.
  • Reassemble in reverse order.
Page 63

8-4 Replacing the Camera Housing

  • Remove the Camera Joint Assy. (see section 8-3 page 62)
  • Remove 3off pozi head screws (M4x6) and 1off pozi head screw (M4x8), with flat and spring washer, and remove the Camera Housing.

Camera Housing

\ \w \\ Pozihead screw (M4x6) ~\o \ /

Pozihead screw (M4x8) with flat and spring washer

Pozihead scrw (M4x6)

  • Reassemble in reverse order.
Page 64

8-5 Replacing the Credit Available / View Change Switch

  • Remove 4off security screw (M5x12) and 2off security screw (5x20).

Security screw (M5x20)

Control Panel Assy

as

  • Disconnect the connectors and remove the Steering Vac-form.
  • Remove the switch/lamp assembly by pulling it out from the switch body.
  • Replace the switch or lamp.
  • Reassemble in reverse order.
Page 65

8-6 Removing the Steering Wheel

  • Remove 3off countersunk socket head screws and remove the centre cap.
  • Remove 3off countersunk socket head screws and remove the steering wheel.

Steering Wheel B

Center Cap

Countersunk socket head screw (M3x16)

Countersunk socket head screw (M6x25)

Note: When replacing the steering wheel ensure that the steering wheel shaft is in the centre position and the wheel is fitted with central spoke pointing downwards.
Page 66

8-7 Replacing the Steeering Assembly

  • Remove the steering vac-form. (see 8-5 page 64)
  • Remove 4off pozihead screws (M5x20) and remove the Steering Support Bracket B.

Steering Support Brkt B

Pozi ead screw (M5x20)

  • Disconnect the Steering Motor and Steering Potentiometer connectors.
  • Remove 4off hex head screws (M6x20) and remove the Steering assembly.
Page 67

8-8 Replacing the Steering Potentiometer

1.

2.

3.

4.

5. Remove the steering assembly. (see 8-6 page 65)

Remove 2off hex socket head screws (M4x10) holding the potentiometer mounting bracket to the front plate.

Slacken the grub screw (M4x10) and remove the potentiometer complete with the mounting bracket.

Hex socket head screw (M4x10)

Grub screw (M4x10) Mounting bracket

Potentiometer

Replace the potentiometer taking care to replace the correct colour wire to the correct terminal.

Reassemble in reverse order.

Note: When refitting the potentiometer ensure that the grub screw engages

6. on the flat of the potentiometer shaft.

After replacing the potentiometer ensure that the game is reinitialized. (see section 7 page 57)

Page 68

8-9 Replacing the Drive Belt

1.

  • Slacken the adjustment screw (hex head M6x60).
  • Slacken the 4off hex nuts to remove the tension from the belt.

Drive belt

Hex nut (M5)

  • Replace the drive belt.
  • Tighten the adjustment screw (M6x60) to tension the belt correctly.
Note: Do not over tension the drive belt.
  • Retighten the 4off hex nuts.
  • Refit the steering assembly.
Note: After replacing the drive belt ensure that the game is re-initialized. Remove the steering assembly. (see 8-6 page 65)

(see section 7 page 57)

Page 69

8-10 Removing the Pedal Assy

  • Remove 4off security screw (M5x20).

Pedal Assy Connectors

  • Withdraw the pedal assembly only sufficiently to disconnect the connectors.

3 Remove the pedal assembly.

  • Reassemble in reverse order
Page 70

8-11 Replacing the Pedal Potentiometer

  • Remove the pedal asembly. (see 8-9 page 68)
  • Slacken the double point screw (M4x8) and remove the potentiometer complete with potentiometer bracket.

Accelerator Assy Hexagon wrench x

Countersunk head washer nut

Connector

Cord grip i

Connector Control Potentiometer

  • Replace the potentiometer ensuring that the correct colour wires go to the correct terminals.

Hexagon nut Accelerator

Potentiometer Potentiometer bracket

Note: When replacing the potentiometer Flat face of the

ensure that the double point screw Potentiometer shaft 1)

engages on the flat of the potentiometer — shaft. Double point scréw

  • Reassemble in reverse order.
Note: After replacing the potentiometer ensure that the game is reinitialized. (see section 7 page 57)
Page 71

8-12 Replacing the Brake Damper

  • Remove the pedal assemble. (see 8-9 page 68)
  • Remove 4off flange socket head screws (M6x8) and remove the brake damper assy.

Flange sockets (M6 x 8)

Flange sockets (M6 x 8) Brake damper

  • Replace the damper assy and reassemble in reverse order.
Note: After replacing the damper ensure that the game is re-initialized. (see section 7 page 57)
Page 72

8-13 Replacing the Pedal Stop Rubber

  • Remove the pedal assembly. (see 8-9 page 68 )

Hexagon bolt (M6 x 60)

Countersunk head washer nut Cushion and spacer

Section view

Spacer Lo = Cushion ——~< ~~

  • Remove the countersunk washer nut and hex head screw (M6x60).
  • Replace the stop rubber.
  • Reassemble in reverse order.
Note: After replacing the damper ensure that the game is re-initialized. (see section 7 page 57)
Page 73

8-14 Replacing the Monitor

The monitor is heavy. Ensure that at least two people are available to remove the monitor, and ensure that there is sufficient space to work safely.

  • Remove the 2 upper security screws (M5x16) and loosen the 2 lower security screws (M5x16) and remove the rear panel

Security screw (M5x16)

Rear Panel

Security screw (M5x16) (Loosen)

  • Disconnect the monitor connectors and earth wire.
  • Remove the steering vac-form. (see 8-5 page 64)
  • Remove the steering wheel. (see 8-6 page 65)
  • Remove 2off pozi head screws (M5x20) and remove the steering support bracket B.

Pozi head screw (M5x20)

Steering Support Brkt B

Page 74
  • Remove 2off security screw (M5x20), 4off security screw (M5x16) and remove the Monitor Centre Moulding.

aS Security screw (M5x20)

Monitor Centre Moulding

Security screw (M5x16) .

a Security screw (M5x16)

  • Remove 2off security screw (M5x20). 5off security screw (M5x16) and remove the Monitor Face Upper, Monitor Face and Monitor Mask as one assembly.

Security Screw (M5x20) \\ Monitor Face (Upper) \ \

Monitor Mask SZ

\\ \

Security Screw (M5x16):

Monitor Face (RHS)

Page 75
  • Remove 4off Hex head screws (M8x16) complete with washers B.

Washer B \ cial

Washer B Ba) de /7 > i YS Hex head screws (M8X16) > O with Flat and Spring Washer i ] eos |

  • Slowly tilt the monitor forward and then lift the monitor out from the front.
  • Replace the monitor.
  • Reassemble in reverse order.
Page 76
  • PARTS

(ey 20] IP Po

@8) Opposite side 29 Vi oO on

  • é i @2—_¢ —} iy 60 Opposite side 81)

a re ne 2, {| = = = = = Le Ez o inn] ion | )

a6 a8

a @

Page 77

Item Description Part No

28|Side Panel - LHSXRO-687-196
29|Side Panel - RHSXRO-687-190
30|Monitor Face - LHSXRO-687-191
31.|Monitor Face - RHSXRO-687-192
32|Monitor MaskXRO-687-193
33|Monitor Face - UpperXRO-687-194
34|Monitor Face - CentreXRO-687-195
39|Adjustable Foot M16 x 9588300079
40|Swivel Castor 75mm59000005
41|Cabinet Side Decal - Race On40000299
42|Cabinet Side Decal - Namco40000300
47|HSB Harness (Link Cable) 2.9mXRO-HSB-029
49|Monitor - Polo 28" Medium Planar84000001
57|Race Number Decal - set 1-840000468
Page 78

Item Description Part No

1Header Acrylic30000044
2|Header Vac-form - LHS46000909

Header Vac-form - RHS 46000910 10 | 4’ Fluorescent Tube 64500039

11|4’ Fluorescent Fitting64000045
Page 79

VA = ey oe [e dq

@ ©

Item Description Part No

1 Repeater PCB (Link PCB) XRO-LINK PCB

2|Schaffner Boot66000017
3|Schaffner Mains In Filter Assy62500010
4|Fuse Holder63500786
5|20mm 4A Slo-Blo Fuse63500624
6|20mm 500mA Q/B Fuse63500608
7|Link Cover Bracket46000904
Page 80

Item Description Part No

1|Steering Vac-Form46000915
2|Steering Dial Decal Set40000397
5|Vac-Form Brushed Decal33000001
6|View change/Credit Available Decal40000398
7|View Change Push Button - Red RPB60200223
8|Credit Available When Lit Push Button60200215
Page 81

Part No Item Description

5Pedal AXRO-463-023
6Pedal BXRO-463-024
7ShaftXRO-463-025
10Brake DamperXRO-463-028
antCushionXRO-462-007
12Spring AXRO-462-009
13Spring BXRO-462-010

14 |Potentiometer 40 008-021

Page 82

cre) 219 | oF

A B

As viewed in the direction Z

Section B-B

Item Description Part No

5|PedalAXRO-463-023
6Pedal BXRO-463-024
7ShaftXRO-463-025
10|Brake DamperXRO-463-028
11|CushionXRO-462-007
12|Spring AXRO-462-009
13|Spring BXRO-462-010

14 |Potentiometer 40 008-021

Page 83

Item Description Part No

Steering Assembly - complete 88800034

1Namco Embossed LogoXAD-295-011
2|Steering Wheel Centre CapXAD-463-414E
3|Steering Wheel - 10" Mountney Black Vinyl88800068
4|Steering Boss46000941
5|Steering Belt81500046
6|Steering Motor cw Gear88800040
7|Potentiometer88800053
Page 84

——n

©

é .

Item Description Part No

4|Seat Rear Decal40000399
5{Rotary Moulded Seat w/Speaker Cutout - Yellow46000874
6|Speaker Plate (LHS) - Black88300603
7|Speaker Plate (RHS) - Black88300604
8|Loudspeaker 4%ec' 20watt6200006
9Adjustable Foot M16x9588300079
10|Fixed Castor 40mm59000008
Page 85

Item Description Part No

1|3.5~6v Panel Mount Meter65000002

20mm Panel Mount Fuseholder 63500786

2Fuse 20mm 2A Q/B63500501

SPDT Toggle Switch -(momentary action) 60000010

Pushbutton Switch 7mm - Red 60000059

5|Miniature Slide Switch60000023
Page 86

10.SCHEMATIC

RiP (PCBE woe r i

osrion LODE DEAESE

230vAC 50Hz MAINS IN 9 CONVERT

Page 87

Evew

r7]eeveen !
!i7[ peri
it | —tae] | meat oiei ali i2
F Eeed:i 4 ig
anre| s1 4 8
ao1 asa!=