CATHODE RAY TOMES

Tempest TM-190 1st Printing

Tempest (rev 3, Revised Hardware) (Atari, 1980) · Technical Manual · 68 pages · 53 sections · original scan

Page 1
Scan of page 1

This page is a drawing, shown as the original scan.

Page 2

GAME SERIAL NUMBER LOCATION Your game's serial number is stamped on a label on the outside of the game. The same number is also stamped on the chassis of the monitor, Regulator/ Audio || PCB, and the Tempest™ Analog Vector-Generator PCB and Auxiliary PCB. Please mention this number whenever calling your distributor for service.

poe

GAME SERIAL NUMBER

IDENTIFICATION TAG

ANALOG VECTOR-

MONITOR GENERATOR PCB

AUXILIARY PCB

REGULATOR/AUDIO Il PCB. g

Page 3

Operation, Maintenance and Service Manual

Complete with Illustrated Parts Lists

Page 4

Copyright © 1981 by Atari, Inc. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher.

The Tempest™ game play, all graphic designs, this technical manual, its accompanying schematic diagrams, the monitor manual, and the troubleshooting guide are protected by the new Copyright Act of 1976.

This Act provides for increased penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles.

In addition, the Aci provides for payment of statutory damages of up to $50,000 in certain cases. Infringers may also have to pay costs and attorneys’ fees, fines up to $25,000, and face an imprisonment of up to one year.

Atari will aggressively enforce its copyrights against any infringers. We will use all legal means to immediately halt any manufacture, distribution or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.

Published by: ATARI INC, 1265 Borregas Avenue PO. Box 427 Sunnyvaie, California 94086

Lithographed in the U.S.A. 9K

Page 5

Notice Regarding Non-Atari Parts

WARNING

Use of non-Atari parts or modifications of your Atari game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

Atari, Inc.’s warranty (printed on the inside back cover of this manual) may be voided, if you do any of the following:

4.) you substitute non-Atari parts in your coin-operated game, or

2.) you modify or alter any circuits in your Atari game by using kits or parts not supplied by Atari.

Not only may the use of any non-Atari parts void your warranty, but any such alteration may also adversely affect the safety of your game, and may cause injury to you and your players.

Page 6

Table of Contents

1 Set-Up Procedures A. New Features... 0... cece cece ete e eee teent teens 3 B. Game Inspection .. 3 C. Game Installation. . 4

  • Voltage Plug Selection . 4
  • Interlock and Power On/Off Switches . 4 D. Self-Test Procedure . a - 6 E. Option Switch Settings 10
  • Bonus Play Feature... 10
  • Coin Mechanism Multipliers . . 10
  • Examples of Option Switch Setinge = F. Game Play
  • Attract Mode ....
  • Ready-to-Play Mode
  • Play Mode ...
  • High Score Initial Mode

2 Maintenance and Repair AL Cleaning 0... e eect e eee teen ete nents 20 B. Fuse Replacement............ 000 e cece eee e ee see. 20 C. TheControl Panel ......... ++. 20

  • Leaf Switch Replacement. .
  • LED Start-Switch Replacement wee
  • Encoder Wheel Maintenance and Repair D. Monitor Removal ..............-2008 24 —. Fluorescent Tube and Speaker Replacement . . 25 F. Printed-Circuit Board Removal .......- +. 26 G. Game Operation... 0.0.6... ccc ce eee ener eee eee 27

3 Illustrated Parts Lists Illustrations and parts lists begin on page ...............-200-0eee 31

Page 7

List of Illustrations

Figure 1 Overview of Game ......... 6. cece cent eee eens 2 Figure 2 Installation Requirements ........ 4 Figure 3 International Voltage Plug Selection 4 Figure 4 Interlock and Power On/Off Switches . . 5

Figure 5 Location of Self-Test Switch, Volume Control and Option Switches ... 6 Figure 6 Self-Test Procedure wees a . bees . Figure 7 Game Option Settings Figure 8 Game Price Settings

Figure 9 Coin Counter Option Settings Figure 10 Opening the Control Panel . Figure 11. Control Panel Wiring .............. te Figure 12 Encoder Wheel Maintenance and Repair ..............00 00 eee ee 22

Figure 13 Monitor Removal .......... 0.0 0e cece cence nee tee teen eet 24 Figure 14 Fluorescent Tube and Speaker Removal Figure 15 — Printed-Circuit Board Removal . Figure 16 Power Distribution Figure 17 Signal Distribution

Illustrated Parts Lists: Figure 18 | Cabinet-Mounted Assemblies Figure 19 Control Panel Assembly. . . Figure 20 EncoderWheel Assembly .............-2+46 Figure 21. Tempest™ Analog Vector-Generator PCB Assembly . bee .. 38

Figure 22 Tempest™Auxiliary PCB Assembly ...........0 0.02 cece eee eee eee 40 Figure 23 Regulator/Audio Il PCB Assembly -- 43 Figure 24 Fluorescent Light Assembly ... Figure 25 Power Supply Assembly for Color

Figure 26 American-Made Coin Door..... 2.0... 6c cece cece cece tne eens 50 Figure 27 _British-Made Coin Door

Page 8
NOTE If reading through this manual does not lead to solving a certain maintenance problem, call Tele-Help® at the Atari Customer Service office in your geographical area, as shown below.

WEST and CENTRAL U.S.A. Parts for all Atari customers in the U.S.A. Game sales and service

Atari, Inc. California Customer Service Office 1105 N. Fair Oaks Avenue P. O. Box 427, Sunnyvale, CA 94086 Telex 17-1103 (Monday-Friday, 7:30-4:00 pm Pacific Time) s From California, Alaska or Hawaii (408) 745-2900 aw From anywhere else in this area toll-free (800) 538-1611

EAST U.S.A. Game sales and service only

Atari, Inc. New Jersey Customer Service Office Cottontail Lane, Somerset, NJ 08873 Telex 37-9347 (Monday-Friday, 7:30-4:00 pm Eastern time) ee From New Jersey (201) 469-5993 ee From anywhere else in this area toll-free (800) 526-3849

EUROPE Parts for all Atari customers in Western Europe. Game sales and service

Atari Ireland Limited European Customer Service Office TIPPERARY TOWN, Tipperary Town, Ireland IRELAND Telex 28165 (Monday-Friday, 9:00-6:00 pm GMT)

BZ 06252155

vi

Page 9

Set-Up Procedures

Introduction

This manual, written for game operators and service technicians, describes the Tempest™ game. Chapter One explains new game features, game set-up, self-test procedures, option switch settings, and game play. Chapter Two consists of maintenance and repair information. Chapter Three contains illustrated parts lists.

Page 10
WARNING: SHOCK HAZARD

Connect this game only to a grounded 3-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electric shock if this game is not properly grounded!

ATTRACTION PANEL

Op ENCODER-WHEEL CONTROL

CONTROL PANEL

COIN DOOR

CASTORS

Figure 1 Overview of Game ‘COLOR XY MONITOR

ANALOG VECTOR. GENERATOR PCB

AUXILIARY PCB

REGULATOR! AUDIO PCB

POWER SUPPLY

POWER ON/OFF SWITCH N

Page 11

A. New Features

The Tempest™ game has five new features. Even if you are familiar with Atari games, you should note these important differences. The new features are: @ Color X-Y Monitor and Game PCBs. Tempest is Atari's first color XY game. The color monitor produces a great number of colors in varying intensities. Atari’s X-Y game circuitry has been redesigned for a color display and placed on a single PCB. @ Game Play. Atari introduces Skil//-Step™, and 99 levels of play on 16 different playfields. A demonstration mode allows you to accelerate through 98 levels of play. In addition, a special switch setting lets you freeze the game action (see Section F, Game Play). @ Encoder Wheel. This new control has a compact, simplified design which makes servicing easy. This control’s circuitry is contained on a single PCB. The very smooth action is designed for greater player accuracy. @ Cabinet Design. The newly designed cabinet has casters at the back of the game, allowing you to easily move the game within your establishment. The attraction panel, with its new construction, uses a polycarbonate decal laminated to tempered glass. Luggage-style latches allow easy opening of the control panel. A wood panel separates the coin box from the components in the back of the game, eliminating the need for a power-interrupt interlock switch on the coin door. Finally, the game and auxiliary PCBs are mounted back-to-back on the cabinet wall and are separated by plastic standoffs. @ Fluorescent light and speaker. For ease of service, the fluorescent light and speaker board slide out of the back of the game. In addition, the game audio is improved because the speaker is positioned in a resonating chamber. These new features, as well as all other major parts in the game, are illustrated in Figure 1. Throughout this manual, wherever one of these new features is mentioned, you will see this a.

WARNING To avoid possible unpleasant electrical shock, do not touch internal parts of the monitor with your hands or metal objects held in your hands!

B. Game Inspection

This new game is ready to play upon removal from the shipping carton. However, your careful inspection is needed to supply the final touch of quality control. Please follow these steps to help us insure that your new game was delivered to you in good condition.

NOTE Do not plug the game in yet!

1.

2. Examine the exterior of the game cabinet for dents, chips, or broken parts. Remove the screws that were used as extra security to seal the rear access panel. Unlock and open this panel, as well as the coin door, inspect the interior of the game as follows: @ Check that all plug-in connectors (on the game harness) are firmly seated. Replug any connectors found unplugged. Don’t force connectors together. The connectors are keyed so they only go on in the proper orientation. A reversed edge connector will damage a PCB and will void your warranty. @ Check that all plug-in integrated circuits on the game PCBs are firmly seated in their sockets. @ Check that the plastic standoffs are in place, holding the PCBs away from each other. @ Remove the tie-wrap that holds the coiled power cord on the inside cabinet wall. Check the cord for any cuts or dents in the insulation. Place the square black plastic strainrelief plate in the wood slot at the bottom of the rear panel opening. @ Note the location of the game’s serial number—it is printed on the special label below the coin door on the front of the game cabinet. Verify that the serial numbers on the Tempest™ Analog Vector-Generator PCB, Tempest Auxiliary PCB, Regulator/Audio II PCB, power supply and monitor are all identical. A drawing of the serial-numbered components is on the inside front cover of this manual. Please mention this number whenever you Call your distributor for service. @ Check all major subassemblies such as the power supply, control panel and monitor for secure mounting.

Page 12

C. Game Installation

°

Figure 2 Installation Requirements

Power 250 watts maximum Temperature 0 to 38°C (32 to 100°F) Humidity Not over 95% relative Space Required 64 x 81 cm (25% x 32 in.) Game Height 176 cm (69% in.)

  • Voltage Selection This game has two possible power supplies: the domestic or international power supply. The domestic power supply operates on one line voltage range: 105 to 135 VAC. The international power supply has three colored voltage selection plugs and operates on the line voltage of almost any country in the world. Before plugging in your game, check your power supply. If the supply doesn’t have voltage selection plugs and a connector at J3 (see Figure 3), then the game operates on any voltage from 105 to 135 VAC. If the supply has the colored voltage selection plugs, make sure that the voltage selection plug on the power supply is correct for your location’s line voltage. Check the wire color on the plug and see if it is correct per Figure 3.
  • Interlock and Power On/Off Switches To minimize the hazard of electrical shock while working on the inside of the game cabinet, an interlock switch has been installed (see Figure 4). It is located behind the access panel. This switch removes all AC line power from the game circuitry when the panel is opened.

Line Voltage Range Voltage Selection Plug Color 90-110 VAC (100) Violet 105-135 VAC (120)* Yellow* 200-240 VAC (220) Blue 220-260 VAC (240) Brown “This is the only plug provided on the domestic power supply.

Figure 3

WARNING Fuse cover must be in place during game operation.

International Voltage Plug Selection

Page 13

Check for proper operation of the interlock switch by performing the following steps: @ Be sure the rear access panel is closed. @ Plug the AC line power cord into an AC outlet. @ Set the power on/off switch to the “on” position. Within 30 seconds the monitor should display a picture.

SAFETY INTERLOCK SWITCH

POWER ON/OFF SWITCH @ Slowly open the rear access panel. The monitor picture should disappear when the panel is opened approximately 2.5 cm (1 inch). Close and lock this panel. @ Ifthe results of the preceding step are satisfactory, the interlock switch is operating properly. If the monitor doesn’t go off as described, check to see if the interlock switch is broken from its mounting or stuck in the “on” position.

Figure 4 Interlock and Power On/Off Switches

Page 14

Tempesi™

D. Self-Test Procedure

This game will test itself and provide data to demonstrate that the game’s circuitry and controls are operating properly. The data is provided on the monitor and the game speaker; no additional equipment is necessary. Part 1 of the self-test procedure includes adisplay of the operator-selectable game options, and game time and high score table information. Part 2 includes ROM and RAM, contro! panel and monitor information.

We suggest you run the self-test procedure any time you collect money from the game or any time you change the game’s options. Refer to Figure 5 for location of the self-test switch and option switches. To run the self-test, follow the instructions outlined in Figure 6.

VOLUME INCREASE:

SELF-TEST TURN CLOCKWISE

SWITCH ws) SELF-TEST SWITCH (EURO- PEAN GAMES) VOLUME CONTROL OPTION SWITCHES

Figure 5 Location of Self-Test Switch,

Volume Control and Option Switches

Page 15

Self-Test Procedure Part 1

The information below is displayed on the screen if you set the self-test switch to on during the attract mode. Look at the displayed numbers for SECONDS ON and SECONDS PLAYED. If these numbers run together vertically, make adjustments to the X and Y outputs of the game PCB.

COIN MECH MULTIPLIER

SWITCH AT N13 (Coin Modes)

SWITCH TOGGLE 1

SWITCH AT L12 (Game Play)

LIVES: PER GAME

NO. OF CREDITS To go to Self-test Part 2, rotate the control knob until the message PRESS FIRE AND SUPERZAPPER FOR SELF-TEST appears on the monitor. Then press both FIRE and SUPERZAP- PER. To end the operator information display, set self-test switch to off.

TIME GAME ON (Seconds)

TIME GAME PLAYED (Seconds)

NO. OF 1-PLAYER GAMES

NO. OF 2-PLAYER GAMES

AVERAGE GAME TIME +——___] > roms ADDER Porcooon SWITCH oeaseood TOGGLE 8

SWITCH AT D/E2 (Game Ditticutty)

GAME DIFFICULTY

COIN MODE

LANGUAGE (English)

Operator Information Display

ig erase High Score Table:

  • Tur control knob until top line reads PRESS FIRE AND START 2 TO ZERO HIGH SCORES. . Press both FIRE and START 2. |. The word ERASING appears and blinks on the screen until the entire table is erased. Wait until the word ERASING disappears before continuing with other tests. en To erase Game Times:
  • Turn contro! knob until top line reads PRESS FIRE AND START 1 TO ZERO TIMES. 2, Press both FIRE and START 1.
  • The word ERASING appears and blinks on the screen until the entire table is erased. Wait until the word ERASING disappears before continuing with other tests.

[Selt-test is continued on next pagel

Page 16
Figure 6Self-Test ProcedurePart 2

Instruction Test Passes Test Fails

1.Set self-testAfter about 5 sec-RAM FAILURE is indicated by a sequence of 1 to 12 tones. You will hear a short low
switch to on (seeonds, the monitor dis-tone and see a short flash on the LED start pushbutton for each good RAM chip, and a.
Figure 5). Press RE-plays the picture be-long high tone accompanied by a long pulse on the start pushbutton for a failing RAM
SET on the PCB, orlow. No sounds arechip. The test stops with the first failing RAM. To restart the sequence, press RESET
turn power off andproduced.on the PCB, or set the self-test switch to off, then to on again. Identify the bad RAM

‘on again. chip with the table below. Example: four short low tones followed by a long high tone indicates failure of RAM at location M3.

Bad RAM Chip Location Long High Tone on Analog Vector-Generator PCB

1st R2 2nd P2

ENTIRE WHITE FRAME VISIBLE3rdRa
AND WITHIN %2-INCH OF4thPa
ROM AT RIMONITOR EDGEieM3
IS BAD.6thM4
SWITCH7thB
TOGGLE1FineSUPERZAPaupio18th4
Is BADsth3
fe10thK4
XxswitcH at ez1th8
(Game Difficulty)1th“4

ROM FAILURE is indicated by a vertical pair of hexadecimal numbers on the top of the screen. The top number indicates the location of the failing ROM(s). Ignore the bottom hexadecimal number in the pair. Identify the bad ROM with the table immediately below.

Displayed No. Bad ROM Chip Location PCB Location

SWITCH B Ri

TOGGLE 8APt
wie8tintAnalogVeo

AT L12 nalog Vector-

ofneOoG| (Game Play)7KIGenerator PCB
; CONTROL:tt

= K

ANOLkNos4Fi

3 el

swircHSTART 4\RIGHT COIN MECH>bt
(Coin Modes)CENTER COIN MECHiN his :

START 2 LEFT COIN MECH

SLAM SWITCH EAROM, Audio and Math Box Failure are indicated by a single letter in the center of the display. Identify the failure with the table below.

Displayed Letter Failure PCB Location

EEAROMC3 (Aux. PCB)
PAudio 1B/C2 (Aux. PCB)
QAudio 2CID2 (Aux. PCB)

R RAM M Math Box**

*If this ROM is bad, you will hear a continuous low tone, and the program may be unable to display a screen image. **Math-box failure is explained in TM-195, Tempest Troubleshooting Guide.

[Self-test is continued on next page]

Page 17

E. Option Switch Settings

  • Bonus Play Feature Tempest™ offers a bonus play for certain combinations of coins inserted. This bonus feature is operator-selectable, meaning you may choose to offer it or not.

With your game set at 25¢ per play, players who deposit four successive quarters or a $1.00 coin, then press the start button, can receive a bonus play. Therefore, players can receive 5 plays for $1.00.

This bonus feature encourages players to insert more money than just the minimum 25¢ required for one game. Various other bonuses are also available (see Figure 8).

  • Coin Mechanism Multipliers Since early 1980, Atari has made available its new coin door which has either two or three coin mechanisms. All recent Atari game PCBs identify the different coin mechanisms in a certain pattern.

The right coin mechs are all the same to the game's logic, regardless of whether you have two or three mechs in your door. In addition, the logic sees the left mech in a 2-mech door and the center mech

te i 3-mech door as the same. Refer to the diagram

elow.

[ese] se] [Ist This pattern is important for you to know, so you can correctly set the “multipliers” for each coin mech. The multipliers determine how much each coin mech will be worth to the game’s logic.

The basic unit of measurement is 25¢, which equals a multiplier of x 1. Therefore, if you have a 25¢/25¢/$1 coin door, you will probably want to set the center and right option-switch multipliers at x1/x 4. (The left coin mech in a 3-coin mech door always has a value of x 1—you cannot change its value.) You can set these multipliers with toggles 4 through 6 on the Tempest™ Analog Vector-Generator PCB switch assembly at location N13. For exact settings of these toggles, refer to Figure 8.

  • Examples of Game

Price Settings

Figure 8 explains the options, giving twelve examples of the most common U.S. situations. The toggles mentioned below are all in the switch at location N13; they only relate to game price, coin mech multipliers, and bonus plays.

Figures 7, 8, and 9 provide “$” symbols indicating Atari’s recommended settings. All toggles are preset in the “on” position as per these recommendations. However, you may change the settings to suit your individual needs.

Page 18

Instruction Figure 6 Self-Test Procedure Part 2, continued

Test Passes Test Fails

  • Activate start, fire, Superzap, slam, and coin switches.”
  • Rotate encoder wheel clockwise and counterclockwise.

4, Observe the white frame around the outside of the screen.

  • Activate SLAM switch.
  • Activate SLAM switch.
  • Activate SLAM switch,
  • Activate SLAM switch.
  • Activate SLAM switch.
  • When satisfied with test, set selftest switch to off Position. As switch activates, you'll hear a beep and 0 changes to 1 on the screen.

The center right hexadecimal number on the screen will increase with counter clockwise motion, and decrease with clockwise motion.

Each frame corner should be within Ye-inch of each monitor bezel corner.

A white cross hatch pattern appears. A character set appears at the bottom of the screen.

Horizontal and vertical lines cross in the center of the screen displaying a large “plus” sign. Audio 0 1 and 2 alternate to produce four tones.

Tests purple, cyan, yellow, white, green, blue, and red for color and intensity. Displays seven groups of vertical lines, each with right line the brightest and left line the dimmest.

A checkerboard pattern touches the sides and corners of the monitor. Rotate the control knob to change color.

A white frame is displayed on the screen. You will not hear a beep and 0 will remain on the screen for the defective switch.

Incorrect progression of numbers indicates encoder wheel harness wires were connected incorrectly. No number change indicates encoder wheel is bad or harness wires are loose.

Consult Tempest™ Troubleshooting Guide.

If display is not centered and symmetrical on the monitor, adjust video pots (see Tempest Drawing Package) on the main PCB. If character set is incorrect, check Vector ROMs (see Troubleshooting Guide).

Lines not crossing indicates video pot on main PCB needs adjusting (see Drawing Package for procedure). No sound indicates failure of an audio amplifier and/or the custom audio chip(s).

Use this pattern for tracking adjustments (see the Color X-Y Monitor Manual).

Use this pattern for purity and convergence adjustments (see Color X-Y Monitor Manual).

Perform math-box signature analysis (see Troubleshooting Guide).

  • Activate coin switches by inserting at least one coin in each coin slot. You will not trip the coin counters as long as you are in self-test.
Page 19

To change toggle positions on the switch assemblies, you need not remove the game PCB. The switches are accessible when the Tempest™ Analog Vector-Generator PCB is mounted in place. To change positions on the Auxiliary PCB slide the board out as far as possible. Figure 7 Game Option Settings When changing the options, verify proper results on the monitor display by performing the self-test. Note that changing an option on any of the following eight toggles will not cause an immediate change on the monitor screen during the attract mode.

Settings of 8-Toggle Switch on Tempest Analog Vector-Generator PCB (at L12) 1 2 4 5 6 Option

On On Off Off

On Off On On

Off On

Off Off

On On On Off

On Off On Off On Off

Settings of 4-Toggle Switch on Tempest Auxiliary PCB (at D/E2) On On On On

Off Off Off Off

On On On Off

On On R Off 8 off 3 On = oft On Off On Off O-credit minimum $ 2-credit minimum

English $ French German Spanish

Bonus life granted at every: 10,000 points 20,000 points $ 30,000 points 40,000 points

50,000 points 60,000 points 70,000 points No bonus life 2 lives per game 3 lives per game $ 4 lives per game 5 lives per game

Game difficulty” Medium $ Easy Hard Medium

Minimum rating range: 1,3,5,7,9 Minimum rating range tied to high score

$ Manufacturer's suggested settings “Refer to F. Game Play, for information on game difficulty. For pricing for “credits,” see Figure 8. Changing toggles 1-5 erases the high score table.

"

Page 20
Figure8Game Price Settings

The white block below contains Atari’s suggested settings. All Circled numbers refer to game pricing labels you should use numbers 1 thru 8 are toggle settings on the 8-toggle switch at lo- with each situation (labels are on the following page). Use the cation N13, on the Tempest™ Analog Vector-Generator PCB. label no. 6 (indicated with 6 ) only if you set toggle 8 at PCB switch assembly L12 to off.

50¢ PER CREDIT:

Bonus Bonus $.75 = 2 plays No bonus $1.00 = 3 plays $1.00 = 3 plays

25¢/25¢ Mechanisms

25¢/$1.00 Mechanisms

25¢ PER CREDIT:

Bonus Bonus

No bonus $.50 = Yplays $1.00 = 5 plays

1234
25ei25¢(2)onononon6G

Mechanisms

567877
OnOnOnOn
25¢/$1.00266

Mechanisms

677
Page 21

Figure 8 Game Price Settings, continued The table below contains the switch settings for those options relating to game price, coin mechanism multipliers, bonus play, demonstration and freeze mode. This information is useful if you want to view all 99 levels of play or freeze the action, if you need to temporarily set the Tempest™ game on free play, or if you have German coin mechanisms in your door.

To achieve bonus plays, all coins must be inserted before pressing the start button. The label no. 6 shown below should be used only if you set toggle 8 at PCB switch assembly L12 to off. The Demonsiration Mode** allows you to choose any level (1-81) in the ready-to-play mode and accelerate through the tubes without having to kill the enemies. Freeze allows you to stop the action. The score is zeroed at the end of the game in this mode.

Set the toggles per the table below for the Demonstration Mode. Next, rotate the control knob. You may choose level 1 through 81 during the ready-to-play mode. Press either START button to accelerate through the tubes. Press the FIRE button to clear the spikes at the bottom of the tube. To freeze play, set switch 1 to off.

Toggle Settings of 8-Toggle Switch on Tempest Analog Vector-Generator PCB (at N13) 3 4 5 6 7 8 Option

Off Off On On

On On On Off

Off On

Off Off

On Off

OnOnOn
OnOnOff

On Off Off

On Off Off Off On On

OffOnOff

Demonstration and Freeze Mode

Off Off Off

On Free play Off 1 coin* for 2 credits On 1 coin* for credit $ Off 2 coins* for 1 credit Right coin mech x 1 $ Right coin mech x 4 Right coin mech x 5 Right coin mech x 6 Left coinmech x 1 $ Left coin mech x 2

No bonus coins $ For every 2 coins* inserted, game logic adds 1 more coin*

For every 4 coins coin*

For every 4 coins” inserted, game logic adds 2 more coins” inserted, game logic adds 1 more

For every 5 coins* inserted, game logic adds 1 more coin* For every 3 coins* inserted, game logic adds 1 more coin*

ae

On Demonstration Mode On Demonstration-Freeze Mode

*In the U.S., a “coin” is defined as 25¢, In Germany a “coin” is 1DM.

$ Manufacturer's suggested settings ** If you press RESET during this mode, game will lock up. To recover, set switch 1 to on.

Page 22

Figure 8 Game Price Settings

ne @@ 2coins

Game Pricing Labels: ‘8 Q@®@ 3 coins @@@@ 4 coins

© @@ 2 coins=1 play A, @ $1 coin =3 plays (Susan B. Anthony coin) e A, @@ 2 coins =1 play ‘ATARI

oO» @ 1 coin = 1 play amg’ 2 play minimum (2 coins = 2 plays) C2) AL” @ 1 coin ATARI

AO @ @ 2 coins = 1 play AraRi the approptiate phrase. Use a permanent-ink water-resis-

(7) A (For operator use—write in

® @ i] @ ae ATARI tant marker.)

Figure 9 Coin Counter Option Settings [These toggles determine which coin mechanisms activate which counters]

Toggle Settings of 4-Toggle ‘Switch on Analog Vector- Generator PCB (K10/1)

4321

Two coin acceptors in the coin door: Three coin acceptors in the coin door:*

OnOffBoth acceptors activate all coinLeft acceptor activates one coin

counters simultaneously. counter; center and right acceptor activate another coin counter. Not for any currently designed 3-mech coin door.

OffOnBoth acceptors activate 2 count-Left and center acceptor activate

ers separately. $$ one coin counter; right acceptor activates another coin counter. g 2

3>OffOffBoth acceptors activate 2 count-_Left, center and right acceptors acti-
37ers separately.vate 3 coin counters separate-

ly. $$$

OnOnBoth acceptors activate all coinAll 3 are same denomination and

counters simultaneously. $ they activate all coin counters simultaneously.

$ Manufacturer's suggested settings for games with 1 coin counter. $$ Manufacturer's suggested settings for games with two coin counters. $$$ Manufacturer's suggested settings for games with optional second and third coin counters.

  • See Drawing Package DP-190 for additional components required for operating the third coin counter.
Page 23

F. Game Play

Atari’s Tempest™ game is a one- or two-player game with a color X-Y or vector-generator monitor. This new monitor, with its 3-color guns and higher voltage, has the same technology that was used in Atari’s black-and-white X-Y monitors. However, this new monitor displays dazzling color and unique visual effects in a spectacular three-dimensional video display. Tempest introduces additional new features: @ Skill-Step™ with 99 skill levels of play @ Operator-information display @ Demonstration mode with freeze Skill-Step™ allows a player to start a game at the same level as was previously achieved (he must start the next game within 30 seconds), without having to start over at the beginning levels. Therefore, skillful players continue to be challenged while less experienced players try to master higher levels. The 99 skill levels of play include 16 different playfields and 6 different targets. The Operator-Information Display is a special sequence in the self-test mode displaying game-time information: number of seconds the game has been on and been played and the average game time. This display lists the number of 1- and 2-player games played, option switch settings, number of lives, level of difficulty, bonus levels, credits, and game pricing information. In this mode, you may clear the EAROM by erasing the high-score table or game-time information. The -vord ERASING appears on the screen during either of these processes. The Demonstration Mode allows you to accelerate through 98 tubes by blasting down the tube toward the far rim without having to kill the enemies. Also, you can freeze game action so you can enjoy the dazzling effects of your journey through the tubes.

Page 24

In addition to these new features, Tempest has five possible modes of operation: attract, ready-toplay, play, high score initial and self-test. Self-test is a special mode for checking the game switches and computer functions. You may enter this mode at any time. When entered, all game credits are retained. Wait at least eight seconds after a game has been played before entering self-test or turning off the power. Otherwise, you may erase the high score table.

  • Attract Mode The attract mode begins when power is applied to the game, after a play or high score initial mode, or after self-test. This mode is continuous and is only interrupted when a game is paid for and accepted, or when in self-test. In the attract mode, the monitor displays one of three possible pictures. One of the pictures is the high score display which lasts for 12 seconds. The score(s) from the last game is at the top of the screen. Following is the highest score and player's initials. The top eight scores and their matching initials appear in the center of the screen. The ranking (from 1 to 99) for the last player(s) appears under the high score table. © MCMLXXxX ATARI appears three lines from the bottom of the screen. Next, if the 2 game option is selected, BONUS EVERY 20,000 alternates with 2 CREDIT MINIMUM. Credits and game price appear on the bottom line of the screen. Finally, at the top of the screen, the words /N- SERT COINS and GAME OVER alternate if there are no game credits. The words PRESS START and GAME OVER alternate if there are game credits. A second picture, lasting for 12 seconds, is the TEMPEST logo. In this sequence, a multicolored square shrinks toward the center of the screen where a very small TEMPEST \ogo appears. The word TEMPEST enlarges in multiple images and changes color. In addition, © MCMLXXX ATARI ap- Pears on the lower half of the screen.

The next picture, lasting from 5 to 60 seconds, shows the last game score, the highest score and its initials, and the words PRESS START or INSERT COINS alternating with GAME OVER at the top of the screen. Credits, game price, and bonus-life information are at the bottom of the screen. In the center of the screen, the picture duplicates a typical game-play sequence with the computer controlling the shooter. The shooter rotates on the end of the tubelike surface that is nearest to the player. Enemies land on the end of the tube that is farthest away from the player and climb toward the shooter. The shooter fires down the tube at the approaching enemies. This scene ends when either the shooter gets shot or spiked or when the shooter kills all the enemies and blasts through the tube into space, and lands on the next playfield. If a player has credits and spins the control-panel knob, the attract mode ends and the words PRESS START appear in ihe center of the screen. Above this is the score from the last game and the highest score and its initials. Below the words PRESS START are credits, game price and bonus life information. If you select the 2-credit minimum option and a player inserts enough money for one credit, the messages INSERT COINS and 2 CREDIT MINIMUM appear in the center of the screen until sufficient coins are inserted for game play.

  • Ready-to-Play Mode This mode begins when sufficient coins are accepted for a game. Each player rates himself by rotating the control knob. The knob moves a square which frames the level he wishes to select. The surface shape and bonus points for that level are also shown on the screen. Bonus point incentive encourages play at a higher level, once that level has been reached. For example, starting at level one and playing through level nine awards 34,000 bonus points. Starting at level nine and playing through that level, awards 59,000 bonus points. If a player reaches a higher level, he may continue to play near that level by pressing start before the attract mode is over. For example, if a player ended his last game in level 20, he may choose level 1, 3, 5, 7, 9, 11, 13, 15, or 17. The ready-to-play mode ends when the any pushbutton is pressed or 10 seconds elapse.
  • Play Mode in the play mode, a player-controlled, yellow clawlike shooter moves around on a three-dimensional tubelike playfield. The shooter rotates on the end of the tube that is nearest to the player. Enemies tand on the end of the tube that is farthest away from the player to climb toward and attack the shooter. The shooter fires down the tube at the approaching enemies. When a player kills all the enemies on a tube, he blasts through the tube, flies through space, lands on a new tubelike playfield, and fights the enemies on that playfield. A player scores points by shooting enemies and by blasting through the tube to anew level. The player loses a life when killed by the enemy. The game is over when all the player's lives are gone.
Page 25

All action occurs on one of sixteen suspended tubelike playfields. The three-dimensional tube surfaces are viewed from the top, so the view of the first playfield (a circle) is like looking into a well. Each playfield is made of 16 rails which connect the nearest to the farthest rim. The playfield color changes every 16 levels: level 1 is blue, level 17-red, level 33-yellow, level 49-cyan, 65-invisible and 81-green. In addition, other events cause playfield color variation. The shooter causes the two rails on which it sits to change color. Superzap causes the playfield to flash as enemies are zapped. Playfield rails flash rainbow colors when a player earns a bonus life. Pulsar enemies cause sections of the nearest rim to disappear, and during the pulse phase, adjacent rails to flash. The player's shooter is controlled by rotating the control-panel knob. The shooter moves around on the nearest rim of the tubelike playfield. The ends of the shooter always touch two adjacent rails. The rails on which the shooter sit change color (yellow in levels 1-16) which gives a flashlight effect and helps the player see the enemies in his lane. A player shoots by pressing the fire button: tap it for one or two shots or press it for all eight shots. A shot is extinguished when it hits an enemy, after it passes the far rim or after it plows a certain distance into an enemy spike. A shot is renewed after it is extinguished so there may be a maximum of eight shots on the screen at one time. A player may use two superzaps per level. A first superzap kills all enemies on the playfield at the time of firing. A second superzap randomly kills one enemy on the playfield. The superzap does not affect enemy shots, spikes or enemies not yet landed on the playfield. Superzap is recharged when the player blasts to a new level.

Enemies in the Tempest™ game

Enemy Description Flipper aw near rim. Kills player by flipping onto shooter. Originates at far rim and rides up two rails. Flips in the tube and on

Tanker <p

Spiker ©

Spike

Fuseball ae

Pulsar vw Player kills flipper by snooting when it is in the tube or when it is “standing” up. Or use Superzap. Originates at far rim or from a spiker. Rides between rails. Carries one or two flippers, fuseballs, or pulsars and expels these when shot or near rim. Kills player by shooting him. Player kills by shooting tanker in the tube. Or use Superzap. Originates at far rim. Rides up between rails on spike which it builds. Kills player by shooting or impaling as shooter blasts through tube. Player kills by shooting spiker in the tube. Or use Superzap. Originates at far rim and builds up toward near rim. Kills player on contact. Player kills by shooting one or more times. Or use Superzap. Originates at far rim or from Tanker. Quickly rides on one rail, jumps to next rail and seeks out shooter. Kills player on contact. Player kills by shooting when fuseball is jumping between rails. Or use Superzap. Originates at far rim or from Tanker. Rides up and down on two rails. Flips on near rim and seeks out shooter. Kills if player is on same rails when it pulses, flips onto or shoots player. Player kills by shooting pulsar in the tube. Or use Superzap. Level First Appears —_— Points for Kill

1 150

3 100

4 50

4 2

a 250, 500, 750

20 200

Page 26

The following hints will help in game play: @ Players should work their way up through the levels to become familiar with game play. Drop down a level if play is too difficult. @ Experienced players should start at highest level possible for maximum points. e On anew playfield shoot at enemy dots at far rim. @ Shoot the flipper as soon as it starts to flip. @ Use long spikes to reclaim shots and kill enemies approaching you from adjacent lanes. @ Avoid shooting fuseball-tankers near the top since emerging fuseballs usually zip up to the top and kill you. @ Use Superzap right before last enemy reaches the top for a few extra points.

  • High Score Initial Mode This mode begins when a player has one of the eight top scores. First, there is a fireworks display. Next, the high score table appears. Finally, a player enters his initials directly into the table following the instructions at the bottom of the screen. The initials and score are highlighted in a special color. You may bypass this mode by pressing the start button. All but the three highest scores are erased whenever you enter the self-test mode, or press the RE- SET button on the game PCB, or turn off the power. This resetting replaces the five lowest scores with fictitious scores and initials. If you erase the special “permanent” memory, the high score table is replaced with eight fictitious scores and initials. Therefore, the table will always be displayed on the screen, possibly consisting of one or more real scores and players’ initials.
Page 27

Maintenance and Kepair

All games require certain maintenance to keep them in good working order. Clean, properly maintained games will attract players and earn more profits.

The most important maintenance item is running the self-test every time you collect money from the coin box. Just looking at a game will not tell you if the encoder wheel, light-emitting-diode switches or leaf switches are broken, or if LEDs have burned out. The self-test will inform you of any of these possible problems.

Second, you should regularly clean the outside of the game and the coin mechanisms. In addition, you will need to regularly clean the leaf switch contacts—or lubricate the encoder wheel: for details see this chapter.

Page 28

A. Cleaning

The exterior of the game cabinet and the metal and acrylic surfaces may be cleaned with any nonabrasive household cleaner. If desired, special coin machine cleaners that leave no residue can be obtained from your distributor.

Do not dry-wipe any of the acrylic panels, because dust can scratch the surface and result in fogging the plastic. The large monitor shield is made of tempered glass and the attraction panel is made of polycarbonate laminated to tempered glass. Both surfaces should be scratch-resistant and easy to maintain.

Bb. Fuse

Keplacement

This game contains six fuses—all on the power supply assembly (not including the monitor fuses). Replace fuses only with the same type as listed in Figure 24 of this manual. See the color X-Y monitor manual, TM-183, for the monitor fuse data.

C. The Control Panel

Prior to repairing or replacing any switch on the control panel or prior to removing the monitor, unplug the game. Then open the coin door.

Reach through the opening and open the luggage style latch, located at each end on the underside of the control panel (see Figure 10). Close the coin door. Lift up on the control panel at the topmost edge and tilt it toward you.

The control panel edge next to the monitor shield has foam tape applied to it. This tape acts as acushion for the glass and prevents spilled liquids entering the cabinet interior. Always make sure this tape is in good condition.

TURN NUT TO RE- MOVE BUTTON: To Remove LED Switch: @ Remove all wires from the faulty switch. @ Turn the switch counterclockwise while holding the black cone-shaped bushing on the outside of the control panel. © Install a new switch using the reverse procedure. Reconnect the harness wires.

Figure 10 Opening the Control Panel and Replacing Switches

Page 29
  • Leaf Switch Replacement The leaf switches operate on 5 volts at a very low current. Therefore, pitting of these switches would be extremely rare. Probably the only reason that pitting would occur is very high-humidity.

Don’t burnish the switch contacts. Burnishing them removes their plating, thus increasing the corrosion of the contacts. The best method of cleaning the switch contacts is to wipe them with a non-abrasive surface. A business card works very well.

To replace any switch, remove the screw with a Phillips-head screwdriver—see Figure 10.

If the black button itself needs to be replaced, turn the stamped nut with a wrench in a counterclockwise direction, as seen from the inside of the control panel. The black ring on the outside of the control panel should not spin, due to its design.

  • LED Start-Switch Replacement The light-emitting diode (LED) switches on the control panel have a very low failure rate. in case a switch should ever be suspect, first test it per the description that follows. To replace the switch, refer to Figure 10.

@ Remove the wires from the suspected switch. @ Set multimeter to ohms scale. Set ohms scale to Rx 1, then zero the meter. @ Connect multimeter leads to appropriate LED switch contacts (see Figure 11 for designation of switch contacts and meter lead placement). @ Check contacts (push and release the switch button) for closed and open continuity. @ If the contacts do not operate sharply or always remain closed or open, then replace the LED switch as outlined in the figure.

NOTE Adjust switches for a narrow gap. When a switch button is depressed, the resulting wiping action of the contacts provides a self-cleaning feature.

ENCODER-WHEEL PCB: BLUE, RED, BLACK & VIOLET WIRES

FIRE AND ZAP SWITCHES: 2 WIRES MAY BE HOOKED UP EITHER WAY

Figure 11

CAUTION Players may receive an electric shock it this control panel is not properly grounded! After servicing any parts on the panel, check that the green ground wire is firmly attached to the metal tab on the inside of the control panel. Only then should you lock up the game.

WHI WHI ITE/BLACK STRIPE ITE

Page 30

Disassemble in the order indicated. (Circled numbers match the steps described below.)

Close the control panel. Remove the two set screws in the control knob. Open the control panel. Unplug the four-pin harness connector. Remove the carriage bolts that hold the encoder wheel frame to the control panel.

To Lubricate:

  • Loosen the two socket-head screws that attach the hub to the shaft.
  • Unsnap the bottom clip ring. Pull the shaft up and out of the frame being careful not to drop the flywheel.
  • Lightly lubricate the washer and the two nylon bushings that snap into the top and bottom the the frame. Apply Nyogel 779 to a cotton swab for this process.

To Replace the Encoder Wheel: 4, Remove the three socket-head screws that attach the top to the bottom flywheel. -

  • Remove the etched encoder wheel and replace it with a new one. Reassemble in reverse, making sure that you center the new wheel between the photosensor device (see the following page). To Replace the Coupler PCB:
  • Remove the two socket-head screws, lock washers and hex nuts that hold the coupler PCB to the frame. 7 Remove the coupler PCB and repair as needed.

Figure 12 Encoder Wheel Maintenance and Repair

Page 31

3. Encoder Wheel Maintenance gi)

and Repair For lubrication, use only Nyogel 779 lubricant

The encoder-wheel control requires lubrication of (Atari part no. 178027-001) on the two bushings of its bushings approximately every 10,000 credits and the encoder-wheel control. as you deem necessary. To lubricate or repair the control, remove the control from the control panel For further instructions on how to replace the and disassemble it as illustrated in Figure 12. coupler PCB or the encoder wheel, see Figure 12.

FLYWHEEL

ENCODER WHEEL PHOTOSENSOR

Figure 12 Encoder Wheel Maintenance and Repair, continued

Page 32

D. Monitor Kemoval

The following procedure should only be performed by a qualified service technician.

WARNING Shock Hazard High voltages may exist in any television or monitor, even with power disconnected. Use extreme caution and do not touch electrical parts of the yoke area with your hands or with metal objects in your hands! Implosion Hazard \f you drop the monitor and the picture tube breaks, it will implode! Shattered glass and the yoke can fly 6 feet or more from the implosion. Use care when re- Placing any monitor. To remove the color XY monitor, follow steps 1 through 6 listed below. Refer to Figure 13.
  • Open the control panel as described in Section C, Opening the Control! Panel. Be sure the game is unplugged from its wall outlet! Remove the monitor shield retainer at the top of the monitor shield. Unscrew the three allenhead screws that secure the monitor shield retainer to the game cabinet. Lift out the tempered glass monitor shield.
  • Carefully remove the four staples that secure the cardboard bezel and remove the bezel. As an extra precaution, we highly recommend you discharge the high voltage from the picture tube.
  • Open the rear access panel and unplug the 15-pin monitor harness connector. Unfasten the monitor chassis from the monitor bracket.
  • Remove the four sets of hardware that secure the monitor frame to the wood frame.
  • Carefully pull the monitor chassis out the front of the game.

Disassemble in the order indicated. (Circled numbers match the steps above.)

Figure 13 Monitor Removal

Page 33

& oe

E. Fluorescent Tube and Speaker Keplacement

WARNING If you drop a fluorescent tube and it breaks it will implode! Shattered glass can fly 6 feet or more from the implosion. Use care when replacing any fluorescent tube.

To replace the speaker or the white fluorescent tube behind the front graphics attraction panel, follow this procedure (see Figure 14):

1.

om outlet. Remove the four Phillips-head screws

Be sure the game is unplugged from the wall

from the top panel at the back of the game. Grasp the handle and slide out the entire assembly. The fluorescent tube and speaker harness has extra length, so you can pull it out about seven inches. If you need to unplug it, the harness connector is accessible from the access panel. To replace the speaker, unplug the two plug-in connectors on the speaker. Unplug the harness and slide the wood board out of the game. Remove the eight staples that attach the speaker to the board. Replace the speaker, reinstall the wood board and reconnect the harness. To replace the fluorescent tube, remove the gray cardboard locking tab at each end of the tube. Slightly rotate the tube up or down, and carefully remove it from the lampholders. Replace with a new tube. Do not snap the tube in vigorously—you may break it, causing an implosion! Replace the locking tabs. Check that the green ground wire is securely attached to the large metal bracket and the ballast transformer on the wood panel. If the tube is not grounded, it may not start. Slide the wood board back into the game and replace the rear panel.

Figure 14 Fluorescent Tube and Speaker Replacement

Page 34

F. Printed-Circuit Board Removal

You may wish to remove the Analog Vector-Generator printed-circuit board (PCB), Auxiliary PCB or the Regulator/Audio II PCB for service or inspection. To do this, refer to Figure 15 and proceed as follows:

  • Open the rear access panel.
  • Locate the hardware that secures the PCBs to the cabinet, and remove this hardware. (The game PCBs have two sets of this securing hardware: a screw, washer and two spacers. The Regulator/ Audio Il PCB has one set of this securing hardware: a screw and washer.)
  • If you are removing the game boards, first remove the two machine screws or tie wraps that fasten the edge connectors to the game PCBs. Then unplug the edge connectors on the game PCBs. If you are removing the Regulator/Audio II PCB, disconnect the five small harness connectors on this board.
  • Carefully slide the PCBs straight out of their slots. The Analog Vector-Generator and Auxiliary PCBs slide out together. Be careful not to twist the boards, as this may loosen connections or components. Replace or repair as required. Reinstall the PCBs, making sure that the connectors are properly plugged in. Note that they are keyed to fit on only one way, so if they don’t slip on easily, don’t force them! A reversed connector will probably damage your game and will void the warranty. Replace the securing screws and fiber washers in the PCB. Reinstall the fasteners used to secure the edge connectors to the PCB. Close and lock the rear access panel. Check that the operation of the game is correct and perform the self-test. This is especially important with any game when you repair a PCB. Normally the only adjustments on this game are option switch changes (made on the 8-toggle DIP switch). Unless you are a qualified technician, do not turn any of the knobs near the game PCB’s edge connector. Also do not turn the small knobs on the Regulator/Audio II PCB.

TEMPEST™ ANALOG VECTOR-GENERATOR PCB

AUXILIARY PCB

REGULATOR AUDIO II PCB

Figure 15 Printed-Circuit Board Removal

Page 35

G. Game Operation

With this manual you received two large sheets that contain the wiring and schematic diagrams for the Tempest™ game. Sheet 1, Side A, includes information that shows the arrangement of these diagrams. These diagrams explain the functions of the circuits and define inputs and outputs.

In addition, you received the Tempest Troubleshooting Guide, which includes information on signature analysis, CAT Box tests and the memory map.

Atari's Tempest is a microprocessor-controlled game. The microprocessor is contained on the game PCB. The game PCB receives switch inputs from the control panel and coin door. These inputs are processed by the game PCBs and output to the monitor, Regulator/Audio Il PCB, and control panel.

The monitor is a color XY monitor. Therefore, the monitor receives signals for the X, Y and Z (red, green and blue signals) axes. Since the location of the beam in the monitor is totally controlled by the X- and Y-axis outputs of the game PCB, the game PCB does not contain a standard sync circuit. The X-and Y-axis inputs to the monitor step in increments of approximately 760 steps for the X (horizontal) axis, and approximately 1000 steps for the Y (vertical) axis. The Z axis controls the intensity of the beam. The Regulator/Audio II PCB performs three functions: 1) it regulates the voltages from the power supply to +5 VDC, 2) it rectifies and filters +22 VDC, and 3) it amplifies the audio output from the Auxiliary PCB.

Specifically, the +5 VDC from the Regulator/Audio Il PCB provides most logic power to the Analog Vector-Generator and Auxiliary PCBs: +22 VDC is regulated on the Analog Vector-Generator PCB to produce + 15; and +22VDC provides power for the audio output of the Auxiliary PCB. The Audio output from the Regulator/Audio II PCB directly drives the game speaker and is controlled by the volume control, mounted inside the coin door.

The power supply is the source of all voltages in the game. These voltages are protected by five fuses in the fuse block on the power supply chassis. The primary winding of the power supply transformer is protected by the cartridge-type fuse in the power supply chassis.

Figure 16 illustrates the distribution of power in this game. Figure 17 illustrates the distribution of signals.

Page 36

FLUORESCENT LAMP.

MONITOR

CONTROL PANEL AUXILIARY PCB

GENERATOR PCB

REGULATORI/AUDIO It PCB

POWER CORD

POWER SUPPLY

ON/OFF SWITCH

Figure 16 Power Distribution ANALOG VECTOR:

Page 37

CONTROL PANEL

ANALOG VECTOR- GENERATOR PCB VOLUME

ZOUT (RED, GREEN, BLUE)

AUXILIARY PCB

REGULATOR/AUDIO II PCB

Figure 17 Signal Distribution

Page 38

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 39

Illustrated Parts Lists

This chapter provides the necessary information for you to order replacement parts for the Tempest™ game. Please note that, for simplicity, common hardware has been deleted from most of these parts lists. This includes screws, nuts, washers, bolts, etc.

The parts lists are arranged in alphanumeric order. For example, all “A-” prefix numbers come first. Following these are numbers in sequence evaluated up to the hyphen, namely 00- through 99-, then 000598- through approximately 190000-.

When ordering parts from your distributor, give the part number, part name, applicable figure number of this manual, and serial number of your game. This will help to avoid confusion and mistakes in your order. We hope the results will be less downtime and more profit from your game.

Atari Customer Service numbers are listed on page vi for your convenience.

Page 40

037732.01 (Griile) Fluor. Light & Spkr.— see Figure 24 A037709-01 (Attract Panel) 03773101 (Retainer)

03774301 037734-01 (Mon, Bezel) (Mon. Shield)

Control Panel Assy.— 21-01 see Figure 19 oarr: (Access Panel)

178013-001 Encoder Wheel— (Latch) see Figure 20

037427-01 (Foam Pad) 19-9032 (ol. Ctl) 69.001 030168-01 Gelresl Gee) (Vol. Ctrl, Bracket)

03626201 Coin Doors— (Coin Box Brkt.) see Figures 26, 27

037704-01 _— (Cab. Assy.) A035943-01, -02, or 03 (Coin Box) 035942-01 (Separator)

178034024 NOTICE TO ALL PERSONS RECEIVING THIS DRAWING (Molding) CONFIDENTIAL: Reproduction forbidden without the spe- Cific written permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor Possession thereo! confers or transfers any right in, or i ccense to use, the subject matter of the drawing or any design of technical information showin thereon, nor any fight to reproduce this drawing or any part thereof. Except for manutacture by vendors of Atati, Inc., and for manufacture 78-3201 under the corporation's written license, no right is granted (Leg) to reproduce this drawing or the subject matter thereof, unless by written agreement with or written permission from ‘the corporation.

Figure 18 Cabinet-Mounted Assemblies A037702-xx B

Page 41

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This ‘drawing is only conditionally issued, and neither receipt nor Possession thereof confers or transfers any right In, or li ‘cense to use, the subject matter of the drawing or any design or technical information shown thereon, nor any right to reproduce this drawing or any part thereot. Except for manufacture by vendors of Atari Inc., and for manufacture tunder the corporation's written license, no right is granted to reproduce this drawing or the subject matter thereof, unless by written agreement with or written permission from the corporation,

ce 037750.01 (Mon. Bracket)

e

hee (Spacer) 78-24012 (Tie Wrap)

A037775-01 (Main Harness) 007882-02 (Sw. Cover) \ Auxiliary PCB— A037450-01 (Interl, Sw./Brkt) see Figure 22

(A037851-01 (PCB Intercon’:) i tal (Vibr. Damper) He e a] ‘Analog Vector-Generator PCB— Hie see Figure 23 Hees dL Ee [= Reg/Audio II PCB— ie aT | Pout A sen Figims,20 see Figure 25

A037453-03, A037454.03, A037455-03 or A037784.03 Schematics, Self-Test Label & Manuals— ‘see parts list on following page

009992.01 (On/Otf Sw. Cvr,) A037470-01 178048-001 (On/Off Sw./Plate) (Caster)

Figure 18 Cabinet-Mounted Assemblies A037702-xx B

Page 42

Figure 18 Cabinet-Mounted Assemblies, continued Parts List

Part No. Description

A035943-01Deep-Well Coin Box Assembly(for all the same coins)
A035943-02Deep-Well Coin Box Assembly(for two different coin denominations—has one separator)
A035943-03Deep-Well Coin Box Assembly(for three different coin denominations—has two separators)
A037450-01Interlock Switch/Bracket Assembly(modified for safety)
A037453-03Strain-Relief Power Cord(U.S. and Canada)
A037454-03Strain-Relief Power Cord(Austria, Belgium, Chile, Denmark, Finland, France, Germany, Greece,

Indonesia, Italy, Netherlands, Norway, Spain, Sweden, and Uruguay)

A037455-03Strain-Relief Power Cord(Australia and New Zealand)

A037470-01 Power On/Off Switch/Mounting Plate Assembly A037704-01 Cabinet Assembly (includes legs and PCB retainers, but not the rear access panel) A037709-01 Attraction Panel with Graphics Assembly A037775-01 Main Harness Assembly A037777-01 Power Harness Assembly

A037784-03Strain-Relief Power Cord Assembly(United Kingdom, Ireland, Lebanon, Saudi Arabia,

India, Hong Kong, Singapore, Egypt, Nigeria, Republic of South Africa, Zimbabwe) A037851-01 Printed-Circuit Board Interconnector The following seven items are the technical information supplements to this game:

DP-190-01Tempest™ Schematic Drawings(Sheet 1)
DP-190-02Tempest Schematic Drawings(Sheet 2)
DP-190-03Tempest Schematic Drawings(Sheet 3)

ST-190 Tempest Label with Self-Test Procedure and Option Switch Settings TM-183 Service Manual for 19-Inch Wells Gardner Color X-Y Monitor TM-190 Tempest Operation, Maintenance and Service Manual TM-195 Tempest Troubleshooting Guide 19-9032 Volume Control 69-001 DPDT Self-Test Switch (for British-made coin doors) 71-2110 Panel Cartridge Lock Mechanism (for rear access panel) 74-5608NN Spacer for Mounting Printed-Circuit Boards

78-240125-Inch Beaded Nylon Tie Wrap(for game PCB edge connectors)

78-3201 Cabinet-Leveling Leg 92-053 19-Inch Wells-Gardner Color XY Monitor 00788202 Interlock Switch Cover 009992-01 On/Off Switch Cover

030168-01Volume Control Mounting Bracket(a/so hoids self-test switch in games with British-made

coin doors) 034536-03 Foam Vibration Damper (for Regulator/Audio i! PCB) 035942-01 Deep-Well Coin Box Separator 036262-01 Coin Box Bracket 036686-01 Card of Game Pricing Labels 037243-01 Metal Base Plate (located underneath power supply) 037721-01 Rear Access Panel (does not include lock) 037427-01 Rear Access Panel Foam Pad 037731-01 Top Monitor Shield Retainer 037732-01 Speaker Grille 037734-01 Monitor Shield 037743-01 Cardboard Monitor Bezel 037750-01 Monitor Support Bracket 178013-001 Spring Draw Latch 178034-024 %-Inch Black Plastic TMolding 178048-001 Rigid Caster

Page 43

78-6900401 (Tape)

(Leaf Switch w/ Button Holder)

A037778-01 (Harness) 178030-003 (Pushbin Assy.) NOTICE TO ALL PERSONS RECEIVING THIS DRAWING

  • CONFIDENTIAL: Reproduction forbidden without the spe 108! cific written permission of Atari, Inc., Sunnyvale, CA. This (Bolt) <rawing is only conditionally issued, and neither receipt nor possession thereof confers or transfers any right in, or Ik ‘cense to use, the subject matter of the drawing or any design or technical information shown thereon, nor any right to reproduce this drawing or any part thereof. Except for manufacture by vendors of Atan, Inc., and for manufacture under the corporation's written license, no right is granted to reproduce this drawing or the subject matter thereof, unless by written agreement with or written permission trom the corporation.

ey-—— 03698501

  • (Sw. Bezel)

75-0108 (Spacer)

62.039 (LED Switch)

[<————- a037737.01 (Ctrl. Pat)

NOTE: Graphics decal is not tield-replaceable. 75-9910NO (Nut)
CAUTION Players may receive an electric shock if this control panel is not properly grounded! After servicing any parts on the panel, check that the green ground wire is firmly attached to the metal tab ‘on the inside of the control panel. Only then should you lock up the game.

Figure 19 Control Pane! Assembly A037736-01 A

Parts List

Part No. Description

A037737-01 Control Panel with Graphics A037778-01 Control-Panel Harness 62-039 SPDT Momentary-Contact Pushbutton Start Switch with Red Light-Emitting Diode 73-834 Control Knob with Skirt 75-0108 Spacer for Encoder Wheel Control 75-941S #10-24 Polymer Nut 75-5108B #10-24 x ¥2-Inch Carriage Bolt 75-9910NO #11 Steel Stamped Nut 78-6900401 Vinyl Foam Single-Coated-Adhesive Tape, /4-inch wide x %inch thick (58 in. required) 036985-01 Black Molded Switch Bezel 160013-001 Leaf Switch and Button Holder (leaf switch only is part no. 160012-001) 178030-003 Pushbutton Assembly

Page 44

Ogn.

036795-01 (Shaft)

178012-002 75-07047 (Ring) SS (Washer) a a J

76-0804-01 (Bushing)

(Washer)

72-8406 036798-01 (Screw) ‘A035220-01 (Encoder Wheel) (PCB Assy)

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Ata, Inc., Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor Possession thereof confers or transfers any right in, or i ‘cense to use, the subject matter of the drawing or any de- ‘sign or technical information shown thereon, nor any right to reproduce this drawing or any part thereof. Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's written license, no right is granted {o reproduce this drawing or the subject matter thereof, un- Igss by writen agreement with or wrlion permiesion fora the corporation.

Figure 20 Encoder Wheel Assembly A037781-01 (Knob)

036796-01 Flywheel)

036797-01 (Flywheel Cap)

Page 45

Figure 20 Encoder Wheel Assembly Parts List

Part No. Description A035220-01 Coupler PCB Assembly A036096-01 Harness Assembly 72-0448 #4 Zinc-Plated Steel Split-Lock Washer 72-8406 #4-40 x 3-Inch Hex Socket-Head Cap Alloy Steel Machine Screw 73-834 Control Knob 75-07047 Nylon Washer 75-914C #4 Hex Socket-Head Cap Steel Machine Nut 76-0804-01 Dual Shoulder Radial Polymer Bushing 036794-01 Frame 036795-01 Shaft 036796-01 Top Flywheel 036797-01 Bottom Flywheel Cap 036798-01 Etched Encoder Wheel 178012-002 “Klip-Ring” Retaining Ring 178027-001 Nyogel 779 Lubricant

Page 46

R33 = — § Sails Re Q

4yeah it]53
-RSa°0

co an

C20cr00eo

19 N

—+3300}-—

35V

5389 +

  • c23 c3l
35Vvfeneeeee

SrinF} BE R25

CSC224245

5.6K 08 Oe 7812 7905

oO R24, 10, 7Wh— Oo

TIP32TOAZ2002ZATDAZ002A
tAlaz_waGoz QSja7

Con is

aan+In

RoTeawt ce BS csc cant

S3IRSco=|o}cist
0lejos)Reel
iTag|Ri4|ORcla
®Ri1,220]R21, ew
0=AE)ftci2gL
|an470

ae oR

4cimoc
470+hCapri

Ty cio

aJ3300uFtP—
-0t55 20

R30 R972 Ot cri

_toFinscoz=[}=0
¥—j+33004F| —

b

5@35

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the spesific written permission of Atari, Inc., Sunnyvale, CA. This drawing Is only conditionally issued, and neither receipt nor possession thereof confers or transfers any right in, or li- Gense to use, the subject matter of the drawing or any design or technical information shown thereon, nor any right to reproduce this drawing or any part thereof. Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's written license, no right is granted to reproduce this drawing or the subject matter thereof, unless by written agreement with or written permission from the corporation.

Figure 21 Regulator/Audio Il PCB Assembly A035435-02 E

Page 47

Figure 21 Regulator/Audio Il PCB Assembly Parts List

Part No. Description (Reference Designations and Locations in Bold) 12-52P7 2.7 Ohm, +5%, 1W Resistor (R5) 16-54P0 4 Ohm, +5%, 5W Wirewound Resistor (R25) 19-100P1015 .1 Ohm, +3%, 7W Wirewound Resistor (R24) 19-315102 1K Ohm Vertical PCB-Mounting Cermet Trimpot (R8) 24-250108 1000 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C13) 24-250477 470 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C1, 4, 12) 24-350226 22 uf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor (C24, 31) 24-350338 3300 uf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor (C9, 10, 18, 19) 24-500105, 1 uf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor (C22, 23) 29-088 -1 uf Ceramic-Disc 25V Radial-Lead Capacitor (C3, 11, 20, 21) 31-1N4002 100V 1-Amp. Silicon Rectifier Type 1N4002 Diode (CR1, 4) 31-1N5401 100V 3-Amp. Silicon Rectifier Type 1N5401 Diode (CR5-8) 33-TIP32 PNP Power Transistor, Type TIP32 (Q2)

34-2N3055NPN Silicon Transistor, Type 2N3055(Q3)

37-LM305, 5V Linear Voltage Regulator (Q1)

37-7812+12V Voltage Regulator, Type 7812(Q8)
37-7905—5V Voltage Regulator, Type 7905(Q9)

72-1608C. #6-32 x %e-Inch Cross-Recessed Pan-Head Corrosion-Resistant Steel Machine Screw 72-6606S #6 x %-Inch Pan-Head Thread-Forming Cross-Recessed Type-AB Zinc-Plated-Steel Screw (Q8) 75-F60405, #6-32 x %4-Inch Binder-Head Nylon Screw (Q85, 7) 75-99516 #6-32 Nut/Washer Assembly

78-16008Thermally Gonductive Compound(Q3)

78-16014 Thermally Conductive Silicon Insulator (Q2, 9)

79-583066-Position Connector Receptacle(J6, 9)
79-583089-Position Connector Receptacle(J7)
79-5834612-Position Connector Receptacle(J10)

79-58354 4-Position Connector Receptacle (J8) 020670-01 Test Point 034531-01 Heat Sink 100015-103. .01 uf Ceramic-Disc 25V Radial-Lead Capacitor (C5, C14) 110000-010 10hm, +5%, %W Resistor (R10, 19) 110000-100 10 Ohm, +5%, %4W Resistor (R11, 20, 29, 30) 110000-101 100 Ohm, +5%, %W Resistor (R4, 12, 22) 410000-102 1K Ohm, +5%, %4W Resistor (R27, 28) 110000-103 10K Ohm, +5%, Y4W Resistor (R13, 14) 110000-271 270 Ohm, +5%, YW Resistor (R1) 110000-330 33 Ohm, +5%, %W Resistor (R3) 110000-392 3.9K Ohm, +5%, YW Resistor (R6)

110000-5625.6K Ohm, +5%, %W Resistor(R32, 33)

110000-752 7.5K Ohm, +5%, %4W Resistor (R7) 110001-221 220 Ohm, +5%, ¥2W Resistor (R9, 21) 116000-220 22 Ohm, +5%, 10W Wirewound Resistor (R31) 122002-102 .001 uf Ceramic-Disc Minimum 25V Radial-Lead Capacitor (C2, 7, 16) 122004-224 .22 uf Ceramic-Disc 25V Capacitor (C6, 8, 15, 17) 137151-002 Type TDA2002A 8W Linear Audio Amplifier Integrated Circuit (Q5, 7)

Page 48

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor Possession thereof confers or transfers any tight in, oF ji cense 10 use, the subject matter of the drawing or any design or technical information shown thereon, not any tight to reproduce this drawing or any part thereof. Except for manufacture by vendors of Atari, Inc., and for manufacture tunder the corporation's written license, no right to reproduce this drawing is granted or the subject matter thereof unless by written agreement with or written permission from the corporation.

137Q04-001

137008 - 001

era} 13 7008-001 1H RIO L374 9

1BISO4-Co: Ls244

sia §

cs RI isiet 4

Leave} <7 co sumynoee ddqgdedy He nae ex

leoizze4-o1 |

c012294-01 Gores EE cia

PEREEEE esas Co GO css (eed I et

ise 4

ess 4 fees j oa if ioe 4 He

coc he bes

Figure 22 Tempest™ Auxiliary PCB Assembly A037585-01

Page 49

Figure 22 Tempest™ Au Parts List ry PCB Assembly

Part No. Description (Reference Designations and Locations in Bold) C012294-01 Audio /O N-Channel MOSILSI Custom Chip (B/C2, C/D2) 21-101153 .015 uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (C9, 10) 24-250107 100 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C56) 24-250476 47 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C13) 24-250477 470 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C37, 38) 24-500105 1 uf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor (C31, 32, 45-47) 24-500476 47 uf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor (C19-21) 29-088 -1 uf Ceramic-Disc Radial-Lead 25V Capacitor (C1-8, 11, 12, 14, 15, 17, 18, 22-30, 33-36, 39-44, 49-55) 31-1N100 100V Type-1N100 Switching Diode (CR3, 4)

37-LM324Type-LM324 Integrated Circuit(K3, K6)
37-4584BType-4584B Integrated Circuit(E6)
37-74109Type-74109 Integrated Circuit(A2)
37-74LS00Type-74LS00 Integrated Circuit(D4)
37-74LS02Type-74LS02 Integrated Circuit(J4)
37-74LS10Type-74LS10 Integrated Circuit(C5)
37-74LS14Type-74LS14 Integrated Circuit(F4)
37-74LS32Type-74LS32 Integrated Circuit(C4)
37-74LS74Type-74LS74 Integrated Circuit(C6, D5)
37-74LS139Type-74LS139 Integrated Circuit(B4, B5)
37-74LS157Type-74LS157 Integrated Circuit(D6)
37-74LS161Type-74LS161 Integrated Circuit(C1, D1)
37-74LS174Type-74LS174 Integrated Circuit(A3, H4)

37-74LS175, Type-74LS175 Integrated Circuit (J3) 37-74LS191 Type-74LS191 Integrated Circuit (A4)

37-74LS244Type-74LS244 Integrated Circuit(E3, H3)
37-74LS374Type-74LS374 Integrated Circuit(B1, F3)
37-74808Type-74S08 Integrated Circuit(E4)

38-MV5053, Type-MV5053 Red Light-Emitting Diode (CR1) 66-114P1T 4-Station, SingleThrow, Dual-Inline-Package Bit Switch (D/E2) 79-42C16 16-Contact Medium-nsertion-Force Integrated Circuit Socket (A1, E1, F1, H1, J1, K1, Li) 79-42C22 22-Contact Medium-Insertion-Force Integrated Circuit Socket (C3) 79-42C40 40-Contact Medium-Insertion-Force Integrated Circuit Socket (B/C2, C/D2, E2, F/H2, J2, KiL2) 020670-01 Test Point

110000-1021K Ohm, +5%, %W Resistor(R1, 5, 7, 41, 45, 53-58, 64, 66-70)
110000-10310K Ohm, +5%, %W Resistor(R3, 4, 8-26, 36, 48-52)

110000-104 100K Ohm, +5%, %4W Resistor (R35, 37, 38) 110000-151 150 Ohm, +5%, %4W Resistor (R2, 30, 31) 110000-221 220 Ohm, +5%, %4W Resistor (R65)

110000-22322K Ohm, +5%, %4W Resistor(R34)

410000-332 3.3K Ohm, +5%, %4W Resistor (R39, 40, 46, 47) 110000-334 330K Ohm, +5%, YW Resistor (R32, 33) 110000-471 470 Ohm, +5%, %4W Resistor (R42-44, 59-63) 110000-472 4.7K Ohm, +5%, ‘“4W Resistor (R29) 110000-473 47K Ohm, +5%, %4W Resistor (R6, 28) [Continued on next page]

Page 50

Figure 22 Tempest™ Auxiliary PCB Assembly, continued Parts List

Part No. Description (Reference Designations and Locations in Bold) 110001-102 4K Ohm, +5%, Y2W Resistor (R27) 122005-103 .01 uf Ceramic-Disc 25V Radial-Lead Capacitor (C16) 128002-102 1000 pf Radiai-Lead Epoxy-Dipped 100V Mica Capacitor (C48)

131003-001Type-1N5257B Zener Diode(CR2)
136002-126Programmable Read-Only Memory(A1)
136002-127Programmable Read-Only Memory(E1)
136002-128Programmable Read-Only Memory(F1)

136002-129 Programmable Read-Only Memory (H1)

136002-130Programmable Read-Only Memory(J1)
136002-131Programmable Read-Only Memory(K4)
136002-132Programmable Read-Only Memory(L1)
137002-001Type-74S86 Integrated Circuit(E5)
137003-001Type-74S03 Integrated Circuit(F5)

137004-001 Transistor Array (E2, F/H2, J2, K/L2)

137161-001Read-Only MemoryER2055(C3)Note: /f you replace this part, you must erase this ROM

before locking up the game. See Figure 6, Self-Test Procedure, in this manual for instructions. If you do not erase the ROM, the self-test will show the ROM to be “defective” by displaying the letter E on the screen.

179014-01212-Pin Polarized PCB Header(J16, J17)
Page 51

ru

? q b Faaccal we aaa Pal = ey rn = coal 55]

= aol Sail | cae = sat jal ae re] ae

pen THER] cal =e me

coca ce Seal Cael we] y a coal all a eR Ue) hb oO oe) Uli oS

Poe OfBokbefol)Mav
vbataGlam)flBl&l
label aft4‘JolE5]e

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, inc., Sunnyvale, CA. This drawing |s only conditionally issued, and neither receipt nor possession thereof confers of transfers any right in, or li Cense to use, the subject matter of the drawing or any de- Sign of technical information stown thereon, nor any right to reproduce this drawing or any part thereof. Excent for manufacture by vendors of Atari, inc., and for manufacture under the corporation's written license, no right is granted to reproduce this drawing or the subject matter thereot, unless by written agreement with or written permission from the corporation.

gee zeae C777 BRED jof ~~ Slo | gaze

og'loj«of!BaQige
9OO|aBe.®
ololglo}we83
2,0]ojo!2eaEeo
lo,9/01Bl339
oololoyBguee
elo,O10Z28R3cF
Bs)GG!gags

FJ vs vl Pose B73 S28 a

“OZLSTpZ Bursn vey OF-61H [1eISUL

Figure 23 Tempest™ Analog Vector-Generator PCB Assembly A037383-01 and -02

Page 52

Figure 23 Tempest™ Analog Vector-Generator PCB Assembly Parts List

Part No. Description (Reference Designations and Locations in Bold)

19-31510310K Ohm Vertical PCB-Mounting Cermet Trimpot(R147, 150, 167, 168)
19-315201200 Ohm Vertical PCB-Mounting Cermet Trimpot(R117, 118)
19-3152022K Ohm Vertical PCB-Mounting Cermet Trimpot(R165, 169)

21-101103, 01 uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (For -02 PCB Assy. only: C63) 24-250107 100 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C57-59) 24-500105 1 uf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor (C61, 62) 27-102182 .0018 pf, + 10%, Radial-Lead Ceramic-Disc 1000V Capacitor (For -01 PCB Assy. only: C67; For -02 PCB Assy. only: C75) 29-006 1 uf, + 10%, 35V Tantalum Capacitor (C60)

29-088uf Ceramic-Disc 25V Radial-Lead Capacitor(C1-19, 22-49, 51, 53-55, 69, 71, 77-80, 82-85,

88-91, 93-97, 99, 102, 103. Also, for -01 PCB Assy. only: C66, 68, 72, 73. For -02 PCB Assy. only: C64, 65, 74, 76) 31-1N100 100V Type-1N100 Switching Diode (CR4)

31-1N91475V Type-1N914 Switching Diode(CR1)

33-2N3906 Type-2N3906 PNP Switching and Amplifying Transistor (Q9-11) 34-2N3904 Type-2N3904 NPN 60V 1-Watt Transistor (Q1-4, 8, 12) 34-2N6044 Type-2N6044 Darlington NPN Transistor (Q5, 7) 37-TLO82CP Type-TL082 Integrated Circuit (A11, D11, D/E12, D/E13, K11) 37-1495 Type-MC1495L Integrated Circuit (A/B12, A/B13, C12, C13)

37-13201Type-LF13201 Integrated Circuit(B11, E11)
37-74LS00Type-74LS00 Integrated Circuit(K9)
37-74LS02Type-74LS02 Integrated Circuit(A7, B5)
37-74LS04Type-74LS04 Integrated Circuit(J11)
37-74LS08Type-74LS08 Integrated Circuit(A4)
37-74LS10Type-74LS10 Integrated Circult(Fa)
37-74LS14Type-74LS14 Integrated Circuit(E6)
37-74LS20Type-74LS20 Integrated Circuit(E9)
37-74LS27Type-74LS27 Integrated Circuit(B6)
37-74LS32Type-74LS32 Integrated Circuit(C3, J8, B9, R7)
37-74LS42Type-74LS42 Integrated Circuit(F7)
37-74LS74Type-74LS74 Integrated Circuit(B8, D3)
37-74LS109Type-74LS109 Integrated Circuit(A8)
37-74LS139Type-74LS139 Integrated Circuit(B3, C1, J2, J5, P7)
37-74LS157Type-74LS157 Integrated Circuit(K2, L2, M2, N2, P8)
37-74LS161Type-74LS161 Integrated Circuit(E4, C8, D8, E8, F8)
37-74LS164Type-74LS164 Integrated Circuit(A9)
37-74LS174Type-74LS174 Integrated Circuit(E7, H8, N8, N9)
37-74LS175Type-74LS175 Integrated Circuit(H7, J7, K8)
37-74LS191Type-74LS191 Integrated Circ it(J6, L8)
37-74LS193Type-74LS193 Integrated Cir(K5, L5, M5)
37-74LS194Type-74LS194 Integrated Circuit(05, D6, E5, F5, H5, H6)
37-74LS244Type-74LS244 Integrated Circuit(A/B1, B/C1, E2, M12, N12, R9)
37-74LS245Type-74LS245 Integrated Circuit(F2,H2,H3)Acceptable substitute is part no. 37-8304B.
37-74LS273Type-74LS273 Integrated Circuit(D9)
37-74LS367Type-74LS367 Integrated Circuit(K7, N7)
37-74LS393Type-74LS393 Integrated Circuit(B4, D4)

{Continued on next page]

Page 53

Figure 23 Tempest™ Analog Vector-Generator PCB Assembly, continued Parts List

Part No. Description (Reference Designations and Locations in Bold)

37-74LS399Type-74LS399 Integrated Circuit(H9)
37-74LS670Type-74LS670 Integrated Circuit(K6, L6,M6) Acceptable substitute is part no. 37-74LS170.
37-74800Type-74S00 Integrated Circuit(F6)
37-74802Type-74S02 Integrated Circuit(C6)
37-74S04Type-74S804 Integrated Circuit(A6, E3, N6)
37-74S808Type-74S08 Integrated Circuit(F3)
37-74S874Type-74S74 Integrated Circuit(B7, C7)
37-748260Type-74S260 Integrated Circuit(C5)
37-74193Type-74193 Integrated Circuit(C4)
37-7815,+ 15V Voltage Regulator(VR3)
37-7915—15V Voltage Regulator(VR1)

38-MV5053 Type-MV5053 Light-Emitting Diode (CR2)

41-3003100 uH, + 10%, Hot-Molded Plastic Fixed R.F. Choke(L1) Acceptable substitute is part

no. 141002-001. 62-001 SPST Momentary Pushbutton Switch (Reset)

66-114P1T4-Station Single-Throw, Dual-Inline-Package Bit Switch(K10/11)
66-118P1T8-Station Single-Throw, Dual-Inline-Package Bit Switch(L12, N13)

78-13003 General Electric RTV #108 Sealing Compound

79-42C1616-Contact Medium-Insertion-Force Integrated Circuit Socket(D7)
79-42C2424-Contact Medium-Insertion-Force Integrated Circuit Socket(D1, E1, F1, H1, J1, K1, L/M1,

MIN1, P1, R1, N/P3, R3)

79-42C4040-Contact Medium-insertion-Force Integrated Circuit Socket(C2)

81-4302 Nylon Snap-In Fastener 90-6013 Microprocessor (C2)

90-7005Random-Access Memory(P9)

90-7033 Random-Access Memory (J3, J4, K3, K4, L3, L4, M3, M4, P2, P4, R2, R4) 99-130430 Voltage-Dependent Resistor (RV1, 2) 020670-01 Test Point 110000-101 100 Ohm, +5%, %4W Resistor (R107, 111) 110000-102 1K Ohm, +5%, %W Resistor (R3, 13, 15, 31, 32, 34, 35, 58, 62-67, 81, 129, 142, 160)

110000-10310K Ohm, +5%, %4W Resistor(R1, 2, 4-12, 14, 16, 17, 38, 60, 61, 84, 87-102, 128, 134, 139, 156,

158. Also, for -01 PCB Assy. only: 105, 106, 112. Also, for either PCB Assy. if you are using part no. 37-74LS170 in locations K6, L3, M6: R19-30)

110000-104100K Ohm, +5%, %4W Resistor(R42-49)

110000-122 1.2K Ohm, +5%, %4W Resistor (R40)

110000-151150 Ohm, +5%, %W Resistor(R86)

110000-152 1.5K Ohm, +5%, %4W Resistor (R137)

110000-15315K Ohm, +5%, %4W Resistor(R130)
110000-221220 Ohm, +5%, %W Resistor(R18, 85)
110000-2222.2K Ohm, +5%, YW Resistor(R37, 52, 54, 56, 131-133, 144, 153-155, 163)
110000-223,22K Ohm, +5%, %4W Resistor(R36, 82)
110000-2722.7K Ohm, +5%, %W Resistor(R138, 141, 157, 161)

110000-331 330 Ohm, +5%, %W Resistor (R51, 53, 55, 57, 74-76)

110000-3923.9K Ohm, +5%, %4W Resistor(R41, 110, 143, 145, 162, 164)

110000-470 47 Ohm, +5%, %4W Resistor (R80)

110000-471470 Ohm, +5%, %W Resistor(R68-73, 135, 136, 148, 151)

[Continued on next page]

Page 54

Figure 23 Tempest™ Analog Vector-Generator PCB Assembly, continued Parts List

Part No. Description (Reference Designations and Locations in Bold)

110000-4724.7K Ohm, +5%, %W Resistor(R39, 59, 77-79)

110000-561 560 Ohm, +5%, %W Resistor (R127) 110000-562 5.6K Ohm, +5%, %W Resistor (R146, 166)

110000-681680 Ohm, +5%, YW Resistor(R140, 159. Also, for -02 PCB Assy. only: R113)
110000-6826.8K Ohm, +5%, YsW Resistor(R50)
110000-683,68K Ohm, +5%, YW Resistor(R83)

110000-821 820 Ohm, +5%, YW Resistor (For -02 PCB Assy. only: R103, 104, 114)

110001-271270 Ohm, +5%, Y2W Resistor(R152)
110003-7527.5K Ohm, +1%, W Resistor(R108, 109, 115, 116, 119-126)

121007-473 .047 uf, + 10%, Radial-Lead Epoxy-Dipped 50V Polycarbonate Capacitor (C100, 101) Acceptable substitute is part no. 121006-473. 122000-225, 2.2 uf, + 10%, 35V Tantalum Capacitor (C56) 122005-103 .01 uf, Ceramic-Disc 25V Radial-Lead Capacitor (C70) 128002-100 10 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C81) 128002-101 100 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C21) 128002-151 460 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C87) 128002-221 220 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C52) 128002-390 39 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C20, 86, 92, 98)

131002-0016.8V, 400 mW, +5%, Zener Diode(CRS)
136002-101Programmable Read-Only Memory(D1) Acceptable substitute is part no. 136002-113.
136002-102Programmable Read-Only Memory(E1) Acceptable substitute is part no. 136002-114.
136002-103Programmable Read-Only Memory(F1) Acceptable substitute is part no. 136002-115.

136002-104 Programmable Read-Only Memory (H1) Acceptable substitute is part no. 136002-116. 136002-105 Programmable Read-Only Memory (1) Acceptable substitute is part no. 136002-117.

136002-106Programmable Read-Only Memory(K1) Acceptable substitute is part no. 136002-118.
136002-107Programmable Read-Only Memory(LIM1) Acceptable substitute is part no. 136002-119.
136002-108Programmable Read-Only Memory(M/N1) Acceptable substitute is part no. 136002-120.

136002-109 Programmable Read-Only Memory (P1) Acceptable substitute is part no. 136002-121.

436002-110Programmable Read-Only Memory(R1) Acceptable substitute is part no. 136002-122.
136002-111Programmable Read-Only Memory(N/P3)Acceptable substitute is part no. 136002-123.

136002-112 Programmable Read-Only Memory (R3) Acceptable substitute is part no. 136002-124.

136002-125Programmable Read-Only Memory(D7)
137002-001Type-74S86 Integrated Circuit(M8)
137149-001Type-74LS11 Integrated Circuit(F9)

137158-002 Type AM6012PC 12-Bit Digital-to-Analog Converter (For -02 PCB Assy. only: A10, F10) Acceptable substitute is part no. 137150-001. 137159-001 Type DAC-O8CN 8-Bit Digital-to-Analog Converter (D10) 137160-003 Type MC3410 10-Bit Digital-to-Analog Converter (For -01 PCB Assy. only: B10, E10) Acceptable substitute is part no. 137160-004.

144000-00112.096 MHz, + .005%, Crystal(Y1) Acceptable substitute is part no. 90-102.

179014-012 12-Pin Polarized PCB Header (J19)

Page 55

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the spe- 148001-001 cific written permission of Atari, Inc., Sunnyvale, CA. This (Speaker) drawing Is only conditionally issued, and neither receipt nor Pp Possession thereof confers or transfers any right in, oF I Gense to use, the subject matter of the drawing or any design or techrical information shown thereon, nor any right to reproduce this drawing of any part thereof. Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's written license, no right is granted to reproduce this drawing or the subject matter thereof, unless by written agreement with or viritten permission from the corporation.

(Wire Nu)

179035-001 (Lampholder)

‘A037457-01 (Hamess) 79-561816P

142028-xxx:’ (Transformer)

037469-01 To ensure that the fluorescent tube (Bracket) starts, make sure the ground wire is firmly attached to both the ballast transformer and the steel lamp bracket. (Tab) 99-1103 (Starter) 99-11009 (Socket)

Figure 24 Fluorescent Light and Speaker Assembly A037740-01 and -02 A

Parts List

Part No. Description

A037457-01 Lighi and Speaker Harness A037540-01 Ground Wire with Ring Lug 70-304 18-Inch 15-Watt Cool White Fluorescent Tube 79-561816P Spring-Connector Wire Nut for 16- to 18-Guage Wires 99-11003 Fluorescent Lamp Starter 99-11006 Fluorescent Lamp Locking Tab (tab consists of two pieces) 99-11009 Starter Socket 037469-01 Steel Lamp Bracket

142028-001 60-Hz 118-Voit Ballast Transformer (used on A037417-01 assembly) 142028-002 50-Hz 118-Volt Ballast Transformer (used on A037417-02 assembly) 148001-001 6 x9-Inch 4-Ohm 15-Watt Oval High-Fidelity Speaker 179035-001 2-Pin Fluorescent Lampholder

Page 56

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the ‘Specific written permission of Atari, inc., Sunnyvale, CA, This drawing is only conditionally’ issued, and neither receipt nor possession thereof confers or transfers any right in, or license to use, the subject matter of the drawing of any design oF technical information shown thereon, nor any right to reproduce this drawing or any part therea!. Ex: cept for manufacture by vendors of Atari, inc., and for manufacture under the corporation's written license, no right to reproduce this drawing is granted or the subject matter thereof unless by written agreement with or written Permission (rom the cotporation, ‘A037395-01 (Transformer Assy.)

A021084-xx (Volt. Plugs) 29-053 (Capacitor) ogasaagt (Fuse Block Cvr.)

79-4411001 (Fuse Post) 78-70501SC (Cap. Bracket) A6-2017002 (Fuse)

A035891-01 (Fuse Harness) 034482-02 (Chassis)

46-301203 (Fuse)

037639-01 (Label)

78-2708 (Bushing)

‘A034630-01 79-3208 _ (Fier Assy) (Fuse Block) 037641-01 (Label) 46-2014002 (Fuses)

‘A035890-01 (Pwr. Harness) 79-15021001 (Term. Block)

A034629-01 3A-MDA3501 (A.C. Harn.) (Rectifier)

Figure 25 Color X-Y Power Supply Assembly A037396 A

Page 57

Figure 25 Color X-Y Power Supply Assembly Parts List

Part No. Description (Reference Designations in Bold) A021084-01 Voltage Plug for 100V (violet) A021084-02 Voltage Plug for 120V (yellow) A021084-04 Voltage Plug for 220V (biue) A021084-05 Voltage Plug for 240V (brown) A034629-01 A.C. Harness Assembly

A034630-01RFI Filter Assembly(FL1)

A035890-01 Power Harness Assembly A035891-01 Fuse Harness Assembly

A037395-01Transformer Assembly(11)

29-053 27,000 uf 15 VDC Electrolytic Capacitor (C1) 3A-MDA3501 Bridge Rectifier, Type MDA 3501 (CR1)

46-20140024Amp. 250 V 3AG Slow-Blow Glass Cartridge-Type Fuse(F2, F4-F6)
46-20170027-Amp. 250 V 3AG Slow-Blow Glass Cartridge-Type Fuse(F1)
46-30120320-Amp. 32 V 3AG Slow-Blow Glass Cartridge-Type Fuse(F3)

78-2708 Nylon Type 6/6 Hole Bushing with %-Inch Inside Diameter x °%,-Inch Outside Diameter x Ya-Inch Thick 78-70501SC 2-Inch Diameter Capacitor Mounting Bracket 79-15021001 2-Circuit Single-Row Terminal Block 79-3206 5-Position 3AG Fuse Block with %-Inch Quick-Disconnect Terminals 79-4411001 Panel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post 034482-02 Power Supply Chassis 034544-01 Fuse Block Cover

037639-01Label tor Fuse Value(F1)
037641-01Label for Fuse Values(F2-F6)
NOTE: A037396-01 power supply assembly has 110V plug A037396-02 has the 100V, 220V and 240V plugs A037396-03 has the 220V and 240V plugs
Page 58

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING 99-10103 CONFIDENTIAL: Reproduction forbidden without the (Inner Pni ‘specific written permission of Atari, Inc., Sunnyvale, CA. Inner Pni. This drawing is only conditionally issued, and neither wiLevers) 75-948S receipt nor possession thereot confers or transfers any right in, oF license to use, the subject matter of the drawing 99-10096 (Hex Nut) 99-10095 oF any design or techrical information shown thereon, nor (Fastener) {ny right to reproduce this drawing or any part thereo!. Ex: (Self-Test Sw.) capt for manufacture by vendors of Atari, Inc. and for manufacture under the corporation's written liGense, no 99-10052 right to reproduce this drawing is granted or the subject matter thereof unless by written agreement with or written permission from the corporation. (Lever) Z 99-1071 : 7 (Siam Sw) 7 99-1073 : (Decal)

75-1408S (Screw) . 4 Part of 99-10095

75-9445 99-1096 (Hex Nut) (Fastener)

99-10063 (Coin Chute) LZ 99-1097 (Insul.) 99-1040 (Coin Inlet Chute) | 9910101 (Coin Chute)

70-11-47 (Lamp),

99-10080 (Lamp Socket)

72-9406S (Screw)

0 _~

N. = 99-10104 (Bar Retnr.)

{Coin Counter)

99-10081 (Key Holder) TAA2KXxx (Coin Mech.)

75-9448 99-10102 / (Brkt. Assy.) (Hex Nut) 99-10065 (Coin Sw) 7296038 COIN RETURN (Return Box) (Screw)

99-106899-10075 thruS99-1047
(Coin Chute)99-10078{Lockt. Coil)

(Sw. Wire) 31-1N4002—Part 99-10042 thru of 99-10047

99-104599-1008(Diode)

(Coin Sw. Assy.) (Retainer) —-75-14128 99-10082 (Screw) (Cover) Figure 26 American-Made Coin Door 71-10Xxxx D

Page 59

99-10012 thru 99-10022, and 99-10107 (Button Assy.)

99-10062 (Button)

99-0009 or 99-10010 (Door)

Part of 99-10074

99-10049 (Locking Arm)

75-5520B (Bolt)

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This Grawing is only conditionally issued. and neither receipt nor possession thereof confers or transfers any right in, oF li cense to use, the subject matter of the drawing or any design of technical information shown thereon, oy any ight to reproduce this drawing or any part thereof. Except manutacture by vendors of Atari, Inc., and tor manufacture under the corporation's written license, no right to reproduce this drawing is granted or the subject matter thereof unless by written agreement with or written permission from the corporation.

71-102201 — U.S. 25¢/25¢ Coin Door 71103202 — U.S. 25¢/25¢/25¢ Coin Door 71-103203 — U.S. 25¢/25¢/$1 Coin Door 71-102204 — German 2 DM/1 DM Coin Door 71-103205 — German 1/2/5 DM Coin Door 99-1055 thru 99-10059 (Button Cover)

99-10074 99-10070, 99-1083 (Lock) thru 99-10092, and 99-10108 (Price Plate)

75-9188 (Hex Nut)

75-915S (Hex Nut)

99-10051 (Frame)

71-102206 — German 1 DM/5 DM Coin Door 71-102207 — Belglan 5 Fri5 Fr Coin Door 71-102208 — Swiss 1 Fri1 Fr Coin Door 71-102209 — Japanese 100Y/100Y Coin Door 71-102210 — British 10 P/10 P Coin Door 72-JA1405B (Screw) 99-1054 (Btn. Housing) 72-HA1404C (Screw)

<a neaaaterer

99-10061 ¢ (Bezel)

99-10066 (Cover)

72-JA1405B (Screw)

99-10048 (Harness—not shown for clarity)

71-102211 — Australian 20¢/20¢ Coin Door 71-102212 — Italian 100 L/100 L Coin Door 71102213 — U.S. 500/50¢ (2 x 25¢) Coin Door 71-103214 — U.S. 50¢/50¢/50¢ Coin Door 71-103215 — U.S. 500/50¢/$1 Coin Door

Figure 26 American-Made Coin Door 71-10Xxxx D

Page 60

Figure 26 American-Made Coin Door Parts List

Part No. Description 31-1N4002 100V Silicon Rectifier 1N4002 Diode 65-4416 General-Usage Low-Force Miniature Switch 70-11-47 Miniature Bayonet-Base Incandescent Lamp, Type #47 74-1201ADU U.S. $1.00 Coin Mechanism 71-4201FCH Swiss 1 Fr Coin Mechanism 71-1201MG German 1 DM Coin Mechanism 71-1202MG German 2 DM Coin Mechanism 71-1205FB Belgian 5 Fr Coin Mechanism 71-1205MG German 5 DM Coin Mechanism 71-1210PE U.K. 10 P Coin Mechanism 71-1220CA Australian 20¢ Coin Mechanism 71-1225CU U.S. 25¢ Coin Mechanism 71-12100LI Italian 100 Lire Goin Mechanism 71-12100Yd Japanese Y100 Coin Mechanism 72-HA1404C #4 x %-Inch Slotted Pan-Head Thread-Rolling Tri-Fluted “Taptite” Cadmium-Plated Screw 72-JA1405B #4 x %-Inch Slotted Pan-Head Thread-Roiling Tri-Fiuted “Plastite” Black Screw 72-9406S #4-40 x 4-Inch Slotted Truss-Head Steel Machine Screw 72-9603S #6-32 x ¥eInch Slotted Truss-Head Steel Machine Screw 75-9158 #%-20 Standard-Pattern Cadmium-Plated Steel Hex Nut 75-918S #8-32 Standard-Pattern Cadmium-Plated Steel Hex Nut 75-944S, #4-40 Polymer Self-Locking Steel Hex Nut 75-948S #8-32 Polymer Self-Locking Steel Hex Nut 75-1408S #4-40 x ¥2-Inch Slotted Pan-Head Steel Machine Screw 75-1412S #4-40 x %-Inch Slotted Pan-Head Steel Machine Screw 755520B #/4-20 x 1%-Inch Round-Head Square-Neck Steel Bolt with Black Finish 99-10008 Switch Wire Retainer 99-10009 2-Mech Coin Door Only 99-10010 3-Mech Coin Door Only 99-10012 U.S, 25¢ Coin Return Button Assembly 99-10013 U.S. $1.00 Coin Return Button Assembly 99-10014 German 1 DM Coin Return Button Assembly 99-10015 German 2 DM Coin Return Button Assembly 99-10016 German 5 DM Coin Return Button Assembly 99-10017 Belgian 5 Fr Coin Return Button Assembly 99-10018 Swiss 1 Fr Coin Return Button Assembly 99-10019 Japanese Y100 Coin Return Button Assembly 99-10020 U.K. 10 P Coin Return Button Assembly 99-10021 Australian 20¢ Coin Return Button Assembly 99-10022 ftalian 100 Lire Coin Return Button Assembly 99-10040 Coin Inlet Chute Assembly 99-10041 Coin Counter Assembly 99-10042 Coin Switch Assembly for U.S. 25¢ and Belgian 5 Fr Coins (silver wire) 99-10043 Coin Switch Assembly for German 1 DM, Swiss 1 Fr, and Japanese Y100 Coins (black wire) 99-10044 Coin Switch Assembly for U.S. $1.00, German 2 DM, and Italian 100 Lire Coins (gold wire) 99-10045 Coin Switch Assembly for German 5 DM, U.K. 10 P, and Australian 20¢ Coins (green wire) 99-10047 Lockout Coin Assembly 99-10048 Coin Door Harness Assembly [Continued on next page]

Page 61

Figure 26 American-Made Coin Door, continued Parts List

Part No. Description 99-10049 Locking Arm Assembly 99-10051 Coin Door Frame 99-10052 Coin Return Lever 99-10054 Coin Button Housing 99-10055 Coin Return Button Cover for Japanese 100Y Coin 99-10056 Coin Return Button Cover for German 1 DM and Swiss 1 Fr Coins 99-10057 Coin Return Button Cover for U.S. 25¢ and Belgian 5 Fr Coins 99-10058. Coin Return Button Cover for U.S. $1.00, German 2 DM, and Italian 100 Lire Coins 99-10059 Coin Return Button Cover for German 5 DM, U.K. 10 P, and Australian 20¢ Coins 99-10061 Coin Return Bezel 99-10062 Coin Return Button 99-10063, Right Half of Coin Inlet Chute 99-10065 Coin Return Box 99-10066 Coin Return Cover 99-10068 Coin Chute 99-10070 U.S. 25¢ Price Plate 99-10071 Slam Switch Assembly 99-10073 Test Switch Decal 99-10074 Lock Assembly 99-10075 Black Switch Wire for German 1 DM, Swiss 1 Fr and Japanese 100Y Coins 99-10076 Silver Switch Wire for U.S. 25¢ and Belgian 5 Fr Coins 99-10077 Gold Switch Wire for U.S. $1.00, German 2 DM and Italian 100 Lire Coins 99-10078 Green Switch Wire for German 5 DM, U.K. 10 P and Australian 20¢ Coins 99-10080 Miniature Bayonet-Base Lamp Socket 99-10081 Wire Key Holder 99-10082 Switch Cover 99-10083 U.S. $1.00 Price Plate 99-10084 German 1 DM Price Plate 99-10085 German 2 DM Price Plate 99-10086 German 5 DM Price Plate 99-10087 Belgian 5 Fr Price Plate 99-10088 Swiss 1 Fr Price Plate 99-10089 Japanese Y100 Price Plate 99-10090 U.K. 10 P Price Plate 99-10091 Australian 20¢ Price Plate 99-10092 Italian 100 Lire Price Plate 99-10094 Fish Paper Insulation 99-10095, Toggle Switch 99-10096 “U’-Type Fastener 99-10097 Fish Paper Insulation 99-10101 Left Half of Coin Inlet Chute 99-10102 Switch and Lockout Coil Bracket Sub-Assembly 99-10103 Inner Panel with Levers Sub-Assembly 99-10104 Anti-Penny-Flip Bar Retainer 99-10105 Anti-Penny-Flip Bar 99-10107 U.S. 50¢ Coin Return Button Assembly (for two quarters) 99-10108 U.S. 50¢ Price Plate (for two quarters)

Page 62

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, inc., Sunnyvale, CA. This drawing is only contitionally issied, and neither recelpt nor possession thereof confers or transfers any right i, or lt Cense {c use, the subject matter of the drawing or any design or technical information shown thereon, nor any right to reproduce this drawing or any part thereof. Except for ‘manufacture by vendors of Atari, Inc., and for manufacture under the corporation's written license, no right is granted to reproduce this drawing or the subject matter thereof, un- Jess by written agreement with or written permission from the corporation.

99-15051 (Lamp Holder)

99-15026 99-15056 (Coin inlet) (Screw for Bezel)

‘Coin Inter)

PART OF 99-15041

99-15055 (Retng. Screw) 99-15041 {Lockout Coil) i 99-5053 (Lockt. Con Spring)

99-15027 (Coin, Ret. Box) 99-15038 (Bezel for Button)

99-15001 thru 99-15012 (Ret. Button)

9915052 - (Spring tor Button) ve

@ 99-15039 : \ (Bezel for Cover, 99-15036 (Cover) 99-15054 “ (Pivot for Lever) o

99-15030 ~~ |aée— (Lockout Flap) nn,

99-15037 (Sw. Adjuster)

99-15029 (Bracket)

99-15042. (Switch) I. 99-15028

aff (Coin Ret. Box)

99-15056 (Screw for Bezel) 99-15060 -_— Sy Cove

Figure 27 British-Made Coin Door 171001-xxx A

Page 63

99-15061 (Dual Entry Frame)

99-15067 (Lock Assy.)

99-15067 (Lock Assy.)

47-1002 (Counter)

NOTICE TO ALL PERSONS RECEIVING THIS ORAWING ‘CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This drawings only conditionally issued, and neither receipt nor 99-15062 Possession thereof confers or transfers any right in, or li. (Hinge) Cense to use, the subject matter of the drawing or any de sign oF technical information shown thereon, nor any right to reproduce this drawing or any part thereof. Except for N manufacture by vendors of Atari, Inc., and for manufacture under the corporation's written license, no right to repro-

  • duce this drawing is granted of the subject matter thereof unless by wntten agreement with or written permission ‘ from the corporation.

99-15066 99-15064' (Screw) (Frame) 99-15065 (Clamp)

171001-001 — British 10 P/10 P Coin Door171001-006 — German 2 DM/S DM Coin Door171001-011 — Hong Kong $1/$1 Coin Door
171001-002 — British 10 P/50 P Coin Door171001-007 — Belgian 5 Fr/5 Fr Coin Door171001-012 — Canadian 25¢/25¢ Coin Door
171001-003 — British 20 P/50 P Coin Door171001-008 — French 1 Fr/1 Fr Coin Door171001013 — U.S. 25¢/25¢ Coin Door
171001-004 — German 1 DM/1 DM Coin Door—_171001-009 — French 2 Fr/1 Fr Coin Door171001-014 — Spanish 25 Pts/25 Pts Coin Door

171061-005 — German 2 DM/1 DM Coin Door —_ 171001010 — Swedish 1 Kr/1 Kr Coin Door 171001-015 — Swiss 1 Fr/1 Fr Coin Door

Figure 27 _British-Made Coin Door 171001-xxx A

Page 64

Figure 27 _British-Made Coin Door, continued 171001-xxx A

Part No. Description 47-1002 Coin Counter 99-15001 Coin Return Button with U.S. 25¢ Price Plate 99-15002 Coin Return Button with U.S. $1 Price Plate 99-15003 Coin Return Button with German 1 DM Price Plate 99-15004 Coin Return Button with German 2 DM Price Plate 99-15005 Coin Return Button with German 5 DM Price Plate 99-15006 Coin Return Button with Belgian 5 Fr Price Plate 99-15007 Coin Return Button with French 1 Fr Price Plate 99-15008 Coin Return Button with Japanese 100 Yen Price Plate 99-15009 Coin Return Button with British 10 Pence Price Plate 99-15010 Coin Return Button with Australian 20¢ Price Plate 99-15011 Coin Return Button with Italian 100 Lire Price Plate 99-15012 Coin Return Button with U.S. 50¢ (2 x 25¢) Price Plate 99-15025 Left Half of Coin Inlet 99-15026 Right Half of Coin Inlet 99-15027 Side Plate of Coin Return Box 99-15028 Base Plate of Coin Return Box 99-15029 Switch Bracket 99-15030. Flap for Lockout Coil (U.S. 25¢) 99-15036 Coin Return Cover 99-15037 Switch Adjuster 99-15038 Bezel for Coin Return Button 99-15039 Bezel for Coin Return Cover 99-15040 Coin Return Lever 99-15041 Lockout Coil 99-15042 Coin Switch for U.S. 25¢ 99-15051 Lamp Holder 99-15052 Spring for Coin Return Button 99-15053 Spring for Lockout Coil 99-15054 Pivot for Coin Return Lever 99-15055 Retaining Screw 99-15056 Screw for Both Bezels 99-15060 Switch Cover 99-15061 Dual-Entry Door 99-15062 Hinge 99-15063 Screw for Hinge 99-15064 Coin Door Frame 99-15065 Clamp for Frame 99-15066 Screw for Clamp 99-15067 Lock Assembly

Page 65

YOUR COMMENTS, PLEASE! Tempest™

1st printing

Your comments will assist Atari in improving the usefulness of our publications. They are an important part of preparing for revisions of manuals and parts catalogs. No postage stamp is necessary if mailed in the U.S.A.

lf you have any technical questions about certain Atari or Kee Games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply:

Name.

Firm CO Distributor

Address. OQ Operator City State Zip C Other. _

Area Code Phone

Page 66

First told

No Postage Necessary if mailed in the United States

=o - BUSINESS REPLY MAIL ———— FIRST CLASS PERMIT NO. 1004 SUNNYVALE, CA es POSTAGE WILL BE PAID BY ADDRESSEE =

Atari, Inc. PC Attn.: Field Service/Coin-Op Division es P. O. Box 427 Sunnyvale, California 94086 a [| PC

€ S ira SESE EE

Page 67

(Ses Been Been aE BUR BES OS EN 2H

,

° ® Phi, ated Nad Satie Sates Mates, Mates’ Nateel Sa

Warranty

Seller warrants that its printed circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its television monitors (in games supplied with monitors) are free from defects in material and workmanship under normal use and service for a period of thirty

  • days from date of shipment. None of the Seller's other products or parts thereof are warranted.

If the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are returned to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
  • Such products are returned prepaid to Sellers’ plant; and
  • Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing.

In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages.

Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms of this order, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products under this order.

The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to yourself and others. Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety.

Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification inciuding labor which is performed by such distributor.

This document is and contains confidential trade secret information of Atari, Inc.

This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc.

Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc. © © S ©

© = AN

Page 68

e ° K2 . " ®@ aie .- _~

e. ao ee 0 rs

ATARI INC @ 1265 BORREGAS AVENUE e e P.O. BOX 427 SUNNYVALE, CALIFORNIA 94086 @ ® 408/745-2000 © TELEX 35-7488 . ATARY eer cin