Robo Kid
Atomic Robo-kid (World, Type-2) (UPL, 1988) · Document · 10 pages · 10 sections · original scan
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
F.C.C. REGULATION COMPLIANCE
This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a CLASS "A" computing device pursuant to subpart J of part 15 of the F.C.C. rules which are designed to provide reasonable protection against such interference when operated in a commercial environment. F.C.C. requires that the sticker that comes with this kit must be on the back of the machine or elsewhere visable when inspected.
KIT CONTENTS
- ATOMIC ROBO KID PC BOARD
- ATOMIC ROBO KID MARQUEE
- CONTROL PANEL OVERLAY
- CONTROL PANEL LABELS, INSTRUCTION CARD
- CONTROL PANEL PLEXI
- WIRING HARNESS 7, MONITOR BEZEL
- JOYSTICK
- BUTTON AND SWITCH ASSEMBLIES
- "NEW GAME" SIGN
- INSTRUCTION MANUAL
MONITOR REQUIREMENTS: This game requires a horizontally mounted raster scan monitor with negative composite sync.
POWER REQUIREMENTS: +5 Volts DC at 7 amps +12 volts DC at 1 amp
CONVERSION PROCEDURE
- PREPARING THE CABINE"
A. Remove the old circuit board B. Remove the control panel, marquee, and any side graphics. C. Remove the old wiring harness being careful to leave the AC wiring to monitor, power supply, on/off switches, and transformer circuitry.
Clean the cabinet thoroughly and repair any visible damage. Painting the cabinet can give your game a “new game" look and caf enhance the earning power of your game. If the monitor screen is scratched it should be replaced.
- KIT INSTALLATION A. Securely mount the PC board to the cabinet B. Attach the wiring harness to the PC board. The connector should be keyed so that it cannot be hooked up backwards. Even if the connector is keyed, check to make sure the wire inputs were connected correctly to the connector, and from the connector to the PC board. The JAMMA label on the connector should face the component side of the PC board. . C. Route the wires labeled "VIDEO" up to the monitor. Attach the wires to the monitor's main circuit board as shown below. The color code is as follows Red wire ----- i red Green wire green Blue wire - blue Black wire ---video ground White wire ---negative composite sync
ELE + Vv +H Cupiine
GND
come sing [|
WELLS GARNER ELECTRO HOME
D. Route the wires labeled "POWER" to the power supply. Connect them as follows: Red wire ---- +5VDC Yellow wire -- +12VDC Black Wire --- Ground_ The blue wire is for -5VDC which is not required for this game. You can use the -5V to power the coin door lights if desired.
E. Find the two wires labeled "SPEAKER" and connect to the speaker. If the sound is scratchy or distorted try reversing the wires.
F. Find the wires labeled "COIN" and route to the coin door. Coin switch 1 and coin switch 2 are wired to the N.O.(normally open) terminal of the microswitch. A ground wire will go to the common terminal.
- CONTROL PANEL A. Remove old control panel buttons and joystick(s). Do not remove the old overlay until the new holes have been drilled. B. Mark and drill the new holes. File any burrs so that the control panel surface is smooth. Remove the old overlay. C. Using the control panel as a template, drill the holes for the control panel plexi. To cut the plexi to size, score deeply with a razor knife or a plastic cutter. Break away the excess with pliers. D. Peel the top half of the protective backing off of the new overlay. Start from the center and smooth the overlay as you go. Leave about one inch of the overlay coming off the top.
SUGGESTED CONTROL PANEL LAYOUT
°O CO ©O 00 B c A c B S
A: JOYSTICK B: WEAPON SELECT C: FIRE D: PLAYER 1 START E: PLAYER 2 START Tide hast
E. F.
G.
- MARQUEE
A.
NOTES: Adhere the control panel function labels. Install the control panel plexi and mount the new buttons and joystick. Hook up the control panel wires. Use the existing control panel harness if possible.
INSTALLATION
Use the original marquee as a template. Score the new marquee deeply and break off the excess with pliers. Before installing the new marquee, make sure the light fixture behind the marquee is working.
TROUBLE SHOOTING
NO SOUND, NO PICTURE
- check for +5 volts at pin #4 (red) and pin #1 (black) with a voltmeter.
- refer to monitor manual and check monitor for proper voltage. GAME HAS SOUND BUT NO PICTURE
- check AC supply to monitor
- check 5 wires to monitor: red, green, blue, sync, and monitor ground. GAME HAS PICTURE BUT NO SOUND
- check the two speaker wires. (pin #10 and L)
- check for +12 volts at pin #6.
- make sure both speaker wires are isolated from ground.
GARBAGE ON THE SCREEN
- adjust power supply so that you have exactly +5 volts at pin #4.
- make sure all socketed EPROMS are securely seated. PICTURE SCROLLS
- recheck connections of SYNC and GROUND between the monitor and the edge connector.
- change sync polarity of your monitor by using a 74LS-04 inverter.
PICTURE UPSIDE DOWN
turn the picture tube 180 degrees, or switch the two horizontal yoke wires and then the two vertical wires.
- see dip switch settings in this manual for screen inversion.
E. Adhere the control panel function labels. F. Install the control panel plexi and mount the new buttons and joystick. G. Hook up the control panel wires. Use the existing control panel harness if possible.
- MARQUEE INSTALLATION A. Use the original marquee as a template. Score the new marquee deeply and break off the excess with 6 pliers. Before installing the new marquee, make sure the light fixture behind the marquee is working.
NOTES:
“ATOMIC ROBO KID" DIP SW INSTRUCTION
piepsw ot 2})3]4
3 lore OFF
nl = 7 ~ ToT ROBO KID, NUMBER 2 orF| ON T OF LIVES 1 = op t 4 ao | ELON ON os | 4 DEMO SOUND OFF OFF
ON a ON TABLE TYPE “[ore| {| qT UP-RIGHT TYPE ON FREE PLAY OFF | OFF + 7 lo
- IN N ONL
DIFFICULTY NORMAL
___ HARD
BONUS 30K, every.100K BONUS—SOK-ONEY Uo Buus [on —-——t
SCREEN INVERSION
DIPSW-2
1COIN IPLAY
1COIN’ 2PLAY
1COIN 3PLAY
1COIN 4PLAY
—2COIN IPLAY 3COIN IPLAY
4COIN 1PLAY
SCOIN 1PLAY
ATOMIC ROBO KID
SOLDER SIDE COMPONENT SIDE
GND GND
GND GND
+5V +5V
+5V +5V
+12V @l[rloalalelwlete
COIN COUNTER 2 © COIN COUNTER 1
SPEAKER (—) wy ° SPEAKER (+)
~ an
VIDEO (GREEN )
i<} (RED ) VIDEO (SYNC) _ wo (BLUE ) ~ ~ (GND ) ae a
COIN SW
START SW
CONTROL mle alo COIN SW
START SW | CONTROL
CONTROL
CONTROL CONTROL
CONTROL CONTROL
CONTROL
CONTROL Ni <[ ><] Sl<] aq] HA) uw) wa)ol zie ir [x lq [mls ie joljalwl>
CONTROL
CONTROL CONTROL
' + 40 different stages in all.
WEAPON
SELECT
weapon select button to choose desired weapon.
¢ When more than one crystal has been captured, use
FIRE
\ FOEO-HID
enhance Robokids firepower.
COMMAND ENTRY, INSTRUCTION The COMMAND ENTRY feature allows the player the opportunity to
start a game at an advanced level. WRITE DOWN THE COMMAND ENTRY CODE FOR FUTURE USE. It is the flashing number shown at the end of games finishing at ACT 5 or higher. To access COMMAND ENTRY follow these
instructions: * ee x INSERT COIN HOLD DOWN FIRE BUTTON PRESS PLAYER 1 START USE JOYSTICK AND FIRE BUTTON TO ENTER CODE. (example:
CPF-1842) PLAYER PLAYER 1 2