CATHODE RAY TOMES

Gee Bee

Gee Bee (Japan) (Namco, 1978) · Manual · 41 pages · 29 sections · original scan

Page 1

420-0199 i a i° l Il I I l i I @PaRT NO. i i i l i l I

I

OWNERS MANUAL

Page 2

GEE BEE

OPERATING INSTRUCTIONS

AND

SERVICE MANUAL

GEE BEE OWNER'S MANUAL

Copyright C 1979 by GREMLIN INDUSTRIES, INC. All Rights Reserved All the information contained herein is the exclusive proprietary property

of GREMLIN INDUSTRIES, and is disclosed in confidence and may not be duplicated nor copied in whole or part nor be used for any purposes other

than that for which disclosed.

Page 3

TABLE OF CONTENTS

INTRODUCTION

IMPORTANT NOTE

REPACKAGING INSTRUCTIONS

REPLACEMENT PARTS L1ST

TRANSFORMER VOLTAGE CONVERSION

GAME CONCEPT AND OPERATION

ADJUSTMENTS AND OPTIONS

MAINTENANCE AND TROUBLESHOOTING PROCEDURES

SCHEMATICS PAGE

Fol lowing Pages

Page 4

INTRODUCTION

This is an electronic game that makes extensive use of digital integrated circuitry and television monitor circuitry. This manual assumes the maintenance technician possesses a general knowledge of solid state circuitry,microprocessor, TTL digital integrated circuitry and T.V. monitor concepts. Any individual NOT knowledgeable in these areas SHOULD NOT attempt repair of the electronic portion of this game. IT SHOULD BE NOTED THAT ANY ATTEMPT TO REPAIR THE GAME IN THE FIELD WITH- OUT EXPRESS CONSENT OF THE FACTORY WILL IMMEDIATELY VOID THE WARRANTY: +:

{MPORTANT NOTES:

NEVER replace any components with anything other than exact replacement parts. (See Parts List located on Service Schematics.

NEVER remove circuit boards/connections while power is on.

DO NOT replace the fuse with anything other than the proper value. A blown fuse indicates an overload condition within the game. Replacing the fuse with a higher value can cause severe damage to internal components if an overload occurs.

ALWAYS consult the manual before attempting repairs.

CORRESPONDENCE regarding this game should be addressed to:

GREMLIN SNDUSTRIES, INC.

8401 Aero Drive

San Diego, California 92123

(714) 277-8700

Page 5
IMPORTANT NOTE

An important service note is posted in this game and is repeated here for emphasis:

IF AT ANY TIME THE T. V. SCREEN SHOWS A MEANINGLESS DISPLAY

OR THE GAME OTHERWISE MALFUNCTIONS, SIMPLY DROP A COIN INTO

THE COIN MECHANISM. THIS SHOULD CORRECT THE PROBLEM. IF

NOT, THE GAME REQUIRES SERVICE.

The circuitry in this game has been arranged so that the insertion of a quarter through the coin mechanism will reset the system. This clears up temporary problems caused by power line disturbances, static, etc.

SERVICE TECHNICIAN NOTE:

The system reset circuitry described above requires that the coin counter is attached to the system. If there is a coin counter problem and no replacement is available, the game will function properly if a 10K Ohm resistor is connected across the coin counter input pins to the video logic board.

Page 6

REPACKAGING INSTRUCTIONS

Should it be necessary to ship this game, follow the instructions below for game recrating:

A) If the original shipping bolts have been discarded (Ref.1), obtain four 5/16-18x1 3/4"! hex head bolts with 5/16" flat washers. Carefully lay the game on its side and attach skid (Ref.2).

B) Place game upright. Tape game keys to upper flange of operator's panel (Ref.3). Crate the game using appropriate shock-absorbent packing material (Ref.4). Include padding on all four corners of the game (Ref.5). After crating is completed, secure package with strapping (Ref.6).

NOTE: If the game is to be shipped to GREMLIN for service or repair, attach a tag identifying the distributor and indicate the service or repair to be made; include the full serial number of the game. GAME MUST BE SHIPPED PREPAID.
Page 7

REPLACEMENT PARTS LIST- GEE BEE

  • LOGIC BOARD PARTS

GREMLIN PART NUMBER

211-0050

230-0023

313-0002

313-0003

313-0006

313-0014

313-0023

315-0018

315-0019

315-0046

316-0137

510-0043

530-0008

  • POWER SUPPLY

211-0042

211-0045

560-0003

  • CONTROL PANEL

250-0068

250-0328

240-0092

475-0007

475-0016

510-0014

510-0045

510-0046

510-0047

  • COIN MECHANISM

220-0071

220-0072

220-0074 DESCRIPTION

44 PIN EDGE CONNECTOR

CRYSTAL, 18.432 MHZ

LM311N IC

LM340 T5 7805¢+5 VOLT REGULATOR)

LM380

LM340 T12 (+12 VOLT REGULATOR)

LM320 T5 (-5 VOLT REGULATOR)

2111 RAM Ic

EPROM 2708 IC

2114/2114L RAM IC

PROM IC 2332

6 POSITION DIP SLIDE SWITCH

HEATSINK

CONNECTOR SOCKET

CONNECTOR PLUG

TRASNFORMER, GAME

BRACKET (FOR VOLUME CONTROL)

BEZEL FOR SERVE SWITCH, TAPERED

KNOB FOR PADDLE CONTROL

10K POT, VOLUME CONTROL.

5K POT, PADDLE CONTROL

SLIDE SWITCH CON BRACKET W/VOLUME)

SERVE SWITCH, ILLUMINATED (W/BULB)

PLAYER 1 START SWITCH (W/ BULB) LEFT

PLAYER 2 START SWITCH CW/ BULB) RIGHT

COIN REJECT BUTTON W/ SPRING

COIN RETURN STOP CU-BOLT W/NUTS) COIN MECHANSIM W/LOCKOUT COIL CU.S.B.)

COIN LOCKOUT COIL

Page 8
  • MISCELLANEOUS PARTS

130-0061

200-0009

220-0035

420-0158

420-0199 GAME SPEAKER

WELLS GARDNER MONITOR B/W

CABINET LOCK

MANUAL, WELLS GARDNER MONITOR

MANUAL, GEE BEE GAME

Page 9

GEE BEE TRANSFORMER VOLTAGE CONVERSION

TO CONVERT THE GAME TRANSFORMER CPART NO. 560-0003) TO 100, 115, OR

230 VAC, REFER TO THE FOLLOWING CHART:

FOR 100 VOLTS: CONNECT THE VOLTAGE INPUT LINES TO PINS 1 AND 2 ON THE XFMR.

FOR 115 VOLTS: CONNECT THE VOLTAGE INPUT LINES TO PINS 1 AND 3.

FOR 230 VOLTS: CONNECT THE VOLTAGE INPUT LINES TO PINS 1 AND 4, WITH PIN

3 CONNECTED TO THE LAMP CIRCUIT.

Page 10

GAME CONCEPT:

GEE BEE is a unique one or two player ball and paddle video game. By controlling a set of paddles, players keep a ball bouncing around the screen to knock out point blocks for high score. There are also bumpers, rollovers and a spinner to aim for, all worth more points. The game accepts up to 9 credits, and each game plays either 3 or 5 balls, depending on which option is set.

GAME START:

When one credit is accepted, the screen displays the number, and only the one-player start button flashes. When two or more credits (up to

  • are displayed, both the one- and two- player start buttons flash. The game is adjustable for the number of coins per credit. (See Adjustments and Options)

GAME PLAY:

If the one-player start button is pushed, the credits count down one; when the two-player button is pushed, the credits decrease by two. Then, the SERVE button flashes and, when pushed, releases the ball onto the playfield. The ball automatically appears after 10 seconds if the serve button is not pushed.

For two-players, GEE BEE features alternate play; that is, when the first player's turn is over, the game resets to allow player two to take his turn. As the alternate action continues, the game remembers each player's score.

The paddle knob causes both paddles to move to the left and right across the screen. The ball bounces off the top side of both paddles, but passes through the upper paddle's bottom side. The ball speed varies, depending on the number of hits made for that turn. When first served, the ball moves at slow speed, then changes to medium speed after the 4th hit with the paddles. On the 8th hit, the ball speed becomes fast. When the high speed ball passes through the spinner, its speed changes to slow, then to medium after the first hit. :

Page 11

SCORING:

There are three kinds of point blocks~ top blocks, side blocks, and Pocket blocks. When the bal! hits a block, that block is erased and the points are added to the score. The point values for the blocks are as follows:

TOP BLOCKS AND LEFT AND RIGHT SIDE BLOCKS:

Row A (outermost row) 1 block = 20 points/1 Bonus (1000 points) for erasing one row.

Row B 1 block = 50 points/1 Bonus (1000 points) for erasing one row.

Row C 1 block - 100 points/1 Bonus (1000 points) for erasing one row.

The points for the left and right pocket blocks are 100, 300, 500, 700, and 900 points, respectively, starting from the bottom of the pocket.

GEE BEE has two bumpers at the top of the screen, which give 10 points when hit. They enlarge momentarily when hit, then return to normal size. When one bank of side blocks is erased, the bumper on that side increases to 100 points. There is also a spinner between the bumpers, which gives points depending on how many times it spins. At slow ball speed, the spinner turns twice; at medium speed, it spins 4 times; and, at fast speed, it spins 6 times. The spinner is normally gray in color, but changes to white when all the top blocks are erased. One revolution is worth 10 points when the spinner is gray, and worth 100 points when it is white.

Five rollovers (circled G's) appear at the bottom of the screen, and are colored gray normally. Each circle changes from gray to white, or white to gray, when a ball passes through it. The change from gray to white is worth 50 points. !f all 5 rollovers change to white, the bonus multiplier display becomes X2, and doubles the score for that turn. No further changes occur after all rollovers become white in one turn.

GEE BEE provides a safety gate to prevent the ball from leaving the playfield through either the left or right side exits. The left or right safety gate comes on when all the left or right side blocks, respectively, are knocked out. When the ball hits the safety gate once, the ball rebounds, the safety gate disappears and 500 points plus 1 bonus (1000 points) are added to the score. If the ball leaves the playfield through one of the side exits (no safety gate) 500 points plus the bonus are added to the score.

Page 12

SCORING (Continued)

Special features in the game include a chance for an extra ball if all left or right pocket blocks are erased. Then, a flashing "EXTRA BALL CHANCE'' arrow appears in the playfield exit on the side with the empty pocket. If the ball leaves through the exit where the arrow is flashing, a ''SAME PLAYER SHOOTS AGAIN'' sign appears and one extra ball is awarded. If a safety gate is displayed in that exit, along with the extra ball signal, the ball is rebounded and an extra ball is awarded. Only one extra ball is given per turn. A free credit is given when all left AND right pocket blocks are erased. In addition, the game gives one free credit if the player's score exceeds a preselectable number. (See Adjustments and Options) The maximum score attainable is 999990; the maximum bonus points are 99000. Finally, GEE BEE produces a number of sounds that vary depending on whether the ball hits a wall, a block. or the paddles.

Page 13

ADJUSTMENTS AND OPTIONS:

  • SELF TEST

GEE BEE has a built-in self test, which enables the owner to check the game for proper operation quickly. By turning on the slide switch inside the coin door, the game runs through the following test:

Self test switch ON:

  • The ball moves diagonally from the lower left corner to the upper right corner of the screen without disappearing. This indicates normal operation.
  • When the ball reaches the upper right corner, the screen displays the following information:

OK or NG

2A

Uor T

Bor 5

A,B,C, or F

o4 For game OK, of NG for a malfunction.

Test value of paddle knob - these digits change successively when the paddle knob is turned to the left or right. With the paddles turned to the right, the display indicates a number between 0 and 16. Any number BELOW 10 means normal operation.

When the paddles are turned all the way to the left, the display counts 0...1...2...

D...E...F...10.... If the value is ABOVE AO, but BELOW FF, the game is functioning normally.*

Indicates whether the game is an upright or table model.

Indicates the number of serve balls per game.

For charge per game (see Chart, following).

For replay points (see Chart, following).

  • A note on this numbering system: The values A-F represent the DECIMAL numbers 10-15. So, a display of AO would be a higher value than, say, 70, 80, or 90, but LESS THAN BO, CO, DO, EO, or FO. In this numbering system (called HEXADECIMAL for 16 digits, O-F, instead of 10 digits, 0-9, in decimal) the highest 2-digit number is FF.
Page 14

ADJUSTMENTS AND OPTIONS (Continued)

3.. If the serve button and the one- and two- player start buttons are lit during test, normal operation is indicated.

  • The game is functioning normally if the game sounds are heard when the serve button, the one- and two- player start buttons, and coin switch are each activated.
  • Turn the self-test switch OFF.
  • The lockout coil de-activates momentarily when the test switch is turned off. The coil re-activates instantly.
  • With the test switch off, the screen displays a cross-hatch pattern for about a second. If it is desired to use this pattern for monitor adjustments, simply turn the test switch on.
  • The game counter advances one step when the self-test is run once.

It. OTHER ADJUSTMENTS:

  • Volume control -- The volume can be adjusted with the control inside the coin door.
  • OPTIONS: (number of balls per game, game charge, and replay points)

The following is a chart of options for GEE BEE, all selectable by means of 6 small slide switches located on the logic board.

aan Posirion SYMBOL on upright off table

3 batls per game 5 balis " “ DETAILS OPTION

number of serve balls

game charge 1 coin, 1 play 1 coin, 2 plays 2 coins, 1 play free game 1 credit up: 2 credits up: credit level

80000 60000 120000 70000 140000 100000 200000 100000 200000 150000 300000

Page 15

MAINTENANCE & TROUBLESHOOTING PROCEDURES:

Always check and confirm the following items when it is believed that trouble has occured.

1.

2.

3.

4,

5.

6. Is the power switch on? Forgetting to turn on the power switch is a comparatively common oversight.

Is the fuse intact? One fuse is provided on the power supply board and on the monitor board. If a fuse blows out after being replaced, it indicates trouble in another component. Always replace with the prescribed capacity fuse, as normal equipment may be damaged if larger fuses are used as a substitute.

Are the connectors firmly inserted?

Turn Poor connector connections must be considered for any trouble ation. Check all related connectors for poor contact. Although disconnected connectors are easily spotted, poor contacts are difficult to locate. The connectors should therefore be pushed in firmly and then loosened to spot poor connections. When testing the PC board connectors, always turn off the power supply. Care should also be taken in relation to the power supply on the other connectors.

power supply off and on again. As the unit may return to normal if the control circuit is reset when the game seems abnormal, turn the power off and on to see if the trouble will clear up.

Are there any metallic objects on the PC board?

Care Ensure that there are no metallic objects on the PC board, as this will be the cause of shorts. Also, refrain from putting any other objects inside the cabinet.

in circuit conductivity tests. When testing conductivity of the circuit with a tester, always disconnect PC board edge connector J2.

The following flow charts are printed here for a logical, step-by-step approach to trouble-shooting the game, should that be necessary.

Page 16

Are the volume controls (inside the coin door and on the game PC board) open

Turn controls to the right

Replace volume controls

fs their an open in the circuit

Faulty Game PC Board Repair Circuit

Contact your Dealer

Page 17

Coins will not be accepted No credit displayed when coin is inserted.

Is the number of credits 9

Reduce the number of credits

Is the coin selector free of foreign objects ls sound produced when the coin mechanism micro switch is actuated by hand during self test.

Is the microswitch normal Adjust the microswitch actuator

Yes

Does credit go_up Replace the microswitch Adjust coin selector

Is the voltage at both ends of the lockout coil over 7V during self test Yes

Replace lockout coil

No_ Faulty Game PC Board Open in the circuit

Yes

Repair Circuit Contact your Dealer

Page 18

Paddle wavers Paddle will Inot go to the ledge Game does not start when game start button is depressed No ball appears when serve button is depressed

Replace (Confirmable by paddle control self-test)

Is sound produced when self test button is depressed

Is trouble corrected Replace switch

Is there an open circuit

Repair wiring

Faulty Game PC Board

Contact your Dealer

Page 19

Start button lamp does not light Serve button lamp does not light Title panel does not light

(Confirmable by self test)

Is the lamp firm in its socket Is the fluorsecent lamp loose

No

'

Is the starter normal

Is the fluorsecent lamp OK Insert firmly Insert firmly

Is the lamp burned out

Replace her eI Is t @ an open fluorsecent lam in the circuit

Asante etreuit |

Faulty Game PC Board Does 100V AV appear at the terminals

circuit

Faulty lamp fixture

Contact your Dealer

Page 20

Screen is completely dark

Is the power switch on Does picture appear when contrast is turned fully to Adjust brightness contrast Is the power supply or monito b urned out Is sound produced when in game Replace fuse

Is there conductivity between PCB edge connector J2 and R-V1, S-V3 of V on the monitor board Bees the screen become light when brightness control is turned fully to the right Does 8V appear between the 8V secondary terminal of the power trans former and 24V between the 24V terminal Does 115V AC appea on the primary of the power transfmr Repair circuit

Do stripes appear on the screen when terminal V3 on the monitor board is touched by hand Does 115V AC appear at the socket Replace power transformer ——+ Does 120V AC appear between th: OV-120V secondary terminals of the power transformer Replace line cord Does 8V AC appear between pins A-C and A-D of the PCB edge connector and 12V AC between Y-W, Y-X Replace noise filter and repair circuit Does 120V AC appear between pins 1 and 2 of monitor connector Faulty game PC Board

re r Looe a —~__._] t —— Repl + Repair circuit | Repair Circuit ] eplece ROWer —_

  • —a transformer |

a | Favtey monitor

  • eae eee el

Faulty monitor

Contact your dealer

Page 21

T25 -QUD2 SH ft A DWG NO OF 9 | REV

APPR

LTR] DATE | REVISION « eoraH DRAFT | CHECK ere LA fens INTIAL ZELEtee FORM NO 001-1500

Page 22

PARTS | TITLE Tor ASSEMBLY GEE - BEE

QTY PER ASSY

Gremiin Industries, tne.

zm 725-Coo2 SH 4

DWG NO OF? 4

PART NO

725 - OCOZ

DESCRIPTION

TOP ASSY. GEE-BEE

SPKE. GAME SPER. COVER COVER J- Ox CABINET GEE -6EE MON VIDEO 22" FORT LOCK MECH COIN SINGLE CLIP SWITCH FE. CASH DZ MoD. B2KT ANGLE ceT. BET FRONT CET. BZKT 2EAGZ C2T BRKT SIDE ceT BEET PLAY FIELD MONITOR PNL |_| PUL PLAYFIELD. B2KT ZETAINER LOGO PALET GEE -SGe&

Page 23

TITLE PARTS TOP ASSEMBLY GEE- BEE] 725-0002 SH3 A LIST DWG NO OF 9 | REV QTY PER ASSY NO PART NO DESCRIPTION REF DES 25| 2B20-Coos CABLE TNE 26| 28O-QOlIO NUT WIZE 27 | 220 -0Coos COUNTER DIGITAL 128) 290-11 LAMP FLOR 18" 29| B0- BIZ LAMP FIX FLOR 18" 20 | 420 -cozs DECAL S/N Zl | 42Zo -caoz DECAL CAUTION! IISY 32] 420 -cO238 DECAL IMPORTANT NOTICE 23B| 420-co40 DECAL wecrcLre

  • 420-0O4 | DECAL S/N SMALL 35| 420-éo DECAL TIP N TELL B6| 420 -COT! IN@T LUNCBATING.
  • 4AZO-0208 WEAP AROUND SIDE 28 | 420-0209 TOP COVER. 39| 4z0-oO124 CORNES STRIP.
  • 420-9198 SHADOW MASK. Al | 420-0199 MANUAL GEE - BEE AZ| 420-0200 DECAL CAZTION GEE - BEE
  • 420 -O20! GRAPHIC SIDE LEFT 44| 420 -oz02 GRAPHIC Site EIGHT 45 | 420-0207 DECAL scome 46| 420-0158 MANIUAL W.G. 23 INCH 47 | 250-0326 PLATE NTS XPME. 2a — 49 | BO - aaa” ASSY JUNCTION BOX. mi 15
Page 24

PARTS | TITLE Gremiin Industries, Inc. TOP ASSEMBLY GEE- SEE | 725-0CO2

LIST DWG NO

QTY PER ASSY

PART NO DESCRIPTION

B25 - acc? a ASSEMBLY XFMR. B25 -CHo i

VIEDD LESic CONTEOW PNL HARNESS CONTROL PNL

HAZNESS SPEAKER

HAZNESS COIN MECH

HARNESS, MAIN

COIN DECAL

PLAYER UECAL SCR. V4-20x/Z2 HEX HD SCZEWH*Gx'/2 PAN HD XREC SHT MTL. SecRZew *lOx!'/2 PAN HD xREC SHT MTL. SCE. 10-24%) PAN HD XBEC L SCR. B-32x(”2 BND. HO XBEC BLK OxIDe SCR. 10-24 1/2 CAZBIAGE [ SCZEW*G x 2/8 PAN HD XZEC. SHT MTL. SR. 6-82 x B/B PANHD XZEC | ecRew *#iox 24 FAN HD KZEC SHT MTL. SCZ I\O-2Z4x | ACREAGE sce. VA-20 «3/8 PAN HD XREL. <Ce. 1O-24 x'/Z2 PAN HD XZEC ScR 6-322 PAN HD K2ZEC SCR 6-32x'/2 TALES HD TAMPER PROOF RIVET, POP 2/16 DIA. x /2 NUT,HEX VY4-20 BAL MIAL NS! 8] 8] A] no} o] DO) AJA) OH] 0) 4) —|-|-|-}-]} -|-|- FORM NO. 001-1501

Page 25

PARTS | TITLE

Gremiin industries, Inc. LIST TOP ASSEMBLY GEE -BEE

T25 —-a00z SHS A DWG NO OFS | REV TE _OTY PER ASSY |

NO PART NO DESCRIPTION REF DES

7S WAGHER SPLIT Lock V4

% NUT HEX 10-24 7 WASHER FLAT *1O

3 WASHER FLAT * ©

2 NUT HEX 6-32

20 WAGHER SPLIT LOCK #6

al NUT HEX 8-32 82 NUT WING 10-24

foi) WAGHER SPLIT LOCK #10

FORM NO. ( 1501

Page 26

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 27

ASSY VIDEO LOGIC| B25-000/ ar 9 2l1- 0004 213-60O1 [19 | 170-0157

a Sa (4) t

XTAL_ /8.432 MHz ZM SIG GM 7805 TR> LM 380 SK

IRI IR2 2 SL

7#LEO4 4P 74L5 08 2M 4U

3V 4H 74 L542 2V,2T 1C_ 746574 4E ABANAT LC _74£5/53 2M /C 74L530 7C FILSERZ 2U,3U Ic 7¢L58 4,4K,4L,4M 10 7418/5! a Pie 74tsi7s 45 [22 | 2.3) za 27] 2a Ey) rat | P32 33] EI 35 | Eq El En 39)

Page 28

TITLE

Pier | ASSY VIDEO LOGIC| 825-000 | |SH#> 5 DWG NO OF 9 G.B.

Ri7 R31 R25,R26 R33,R3t4 R4+3-R48B,R3G +/7K_OHM 470K OHM 9.1K OHM RES DIODE IN4#00Z a [DIODE IN9/4+/IN#/4B |DI,DG-DIO | pT XSTR_ 2NSOGO XSTR_ ZNF¢4O) rOnM NO. 001-1501

Page 29

parts | TITLE Gremlin Industries, Inc. MAIN HARNESS) CES TES] S325- Q00@

DWG NO

DRAWN @&.ULOxwtD

APPR

FORM NO. 001-1500

Page 30

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 31

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 32

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 33

Typ 2 PLCS.

te 4 '

@ 6) ©)

on)

LEVELING FOOT Cc u

Z [|

\.

Oo

section AeA SECTION AL=N JORAWN LL OVO:

a

Page 34

RRVaNaNON G)= Gf) Noiloas To) tb) Ce) te) ~[ _ /QB9® @Be0 | eaco/

  • (2 tz) (2) et (2)
Page 35

LOGIC BOARD /925-0001 MAIN_HARNESS/ 825-0006 CRT MODULE 4200-0009

HARNESS¢ 625-0005 CONTROL PANELZ COIN ACCEPTOR 4 220-0074 25-0002

J4|P4 B=O9A THUS UN B=O DOI Gud ON—

JUNCTION BOX 4807-0009 SDoteusEN— A=Dveve sun] A

B

c

>

Ee

Ss

Fe

5)

K

L re) M

W

N

IP

g

iS

af le u

Vv

w

x

E) Y

z

POWER_SUPPLY/825-0007

Page 36

WITAL PE BASS a

-5O WIDE NYLON STRAP TVR,

PARTS LIST

TOP ASSEMBLY GEE - BEE CONTAINER DETAIL

Page 37

REVISIONS DESCRTION PELEAEED mato

VSN

SOUND

pog BDI

Bp2

D3 INDIES .Olpt

$12

Qe 2N440)

D7

be

a

03 74151

DI

Pe ec

Ey VOL READ

b2 N4002

os IN#00%

&

WW

1, ALL 74 SERIES ARE LB.

NOTES: +0048 C2,072-26, 229,c85 = Olas SOV

NOMENCLATURE OR DESCRIPTION

ACHEMAT/C —

GB V/DEO LOG!

RRO B25-dOOI\A

Page 38

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 39

wef Tar

|Ale

las.

as

lar z

EY

thas

Lh ai

cx ik Qc Qi COUNTER

MH? —o— ay a

7474 YR Ko +10

s ar

Lame 3 7N 4060

Roe

ven “ et : ANSOGE LAME Z ps7 40,

© B29 _¥ 95 2 h caer 2N 5060 Baw Ee RSS 7486 210

PART NOMENCLATURE {0eNTIFNNG WO. OR OESERPTON PARTS LIST.

PR fea DCMEMATIC —— Pm lon GR VIDEO LOGIC ae) Bi INKED

ZB inaooe,

AV UNREG

bie

Ze ay)

Page 40

aSOLDER LUG Zn-0027

AMP PIN 2il- 0041 13 PLACES

15 PIN AMP 2u- 0049

  • | GRN SHLOCABLE| SH/ELD

SHLD CABLE

WHT/ BRN

BLU BLU

RED

RED WHT7/G RN WHT/GRN [BRN | WHT. REVISIONS DESCRIPTION

BRACKET 250-0068 CONN QUICK 211-0019 B PLAces

RIGRIZRI-V

PART OR IDENTIFYING NO. NOMENCLATURE OR DESCRIPTION

[UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES TOLERANCES ARE: FRACTIONS DECIMALS _ ANGLES PARTS LIST

XX oe XXX = ‘APPROVALS

Ve ae® aN) PRAWN Wuyreanay | ey ae

H=2828 HARN COIN MECH

  • CABLE TIEB 280-0005 APPRO. &”" APART

at his Wine

. NEXT ASSY USED ON

N (6) TE 5 . APPLICATION

DO NOT SCALE DRAWING

Page 41

SHRINK TUBING ON PINS GM PL. HARNESS _ASSY UTEM_)

|. SECURE HAZNENSS USING TEM 12, APPtox EVERY 6.00 IN. (29 Zea) NOTES: 3 2 1

REVISIONS. aa} fi-y | Piz) | aompenl = ease ‘tate | arpppeo 42 PI-x PI-20 | suMPEq 17a ALRELERSED pec |i es Bs Al PI-Ww PI-I9 JUMPER) 17 ao| pyr | Pi-e [cumper| 7a 39 PI-D Pl-@ JUMPER! 1/4 35| pi-c | Pi-3 | Jumper] 74 37] P1-a_ | P1-1,8,2|uumPer| 74 Wire| FROM TO |coLOR| cn |B SR-3 8-9 WHTIGEN. & ‘a5 53-7 J3-4 ced ieee 34 JB- GND GEN. 12 a3 IR RB GNDSEN ta

JB-A aK 9s 3 J6- 8B WHT. 9S 20 JB-GND GEN. 95 22 PIl-22 Jo-1 PUK a 2B Pla JSB- SuLD 88 27 PI-z2 3-9 WHT/GEN. 6B

26 9 P23 GRY. 38 2 P-3 e2-s5 BRN. 23 ca pl-4 Pe- 4 Ome. 33

Pin vB-S Bu 86

22 1-17 J3- © wHT/BEN 88

=e zo Pl-u M4~ 6 WHT/BLK 78 i aD Pl-ie V4-S WHT/GRY 78 9 m-T V4-4 WHT/VIO. 78

Bo PI-IS Jo 2 UT 82

TPH SSH noc Sot P14 A= WHT /GeN. 78 i PI-E JS- 2 MOS

PBB t wHT. oa

iB PI-P vB-2 BRN. 88

2 Pine J4-1 wHT/eeD 78 \ 6 pil Plans J4-2 whTiows 76 . % 1 to) PtH J4-3 WHT/BU 78 9° PI-M wB-8 Gry 6

B Flv J4-7 PNK 1s 7 ei-J J4- 9 WHT/YEL. 7a

e Cl-F 43-4 ED 86 , s aA-S J3-15 sapcwrr se,

| 4 PI-E 43-12 woaeK BB {3 Pi-zo P2-2 wats )e Pi-c va-10 Ben. fy) prea pest vio. [WIRE FROM TO COLOR “inch

  • LIST

Se ERITEN PARTS LIST

Sen Drege, Catiforase 91623

MAIN, HARNESS GEE - REE

[SOE TERT NO TORAWING WO. a ee od Used on APPLICATION, 825-0006) A