Pandoras Palace
Pandora's Palace (Konami / Interlogic, 1984) · Manual · 12 pages · 13 sections · original scan
a> a> wWaxtorns wanncc’ |
CONVERSION KIT INSTRUCTION MANUAL
FOR ANY VERTICALLY MOUNTED RASTAR SCAN MONITOR GAME
Konami interlogic ©100
TABLE OF CONTENTS
Page
Conversion Kit Contents Inside Cover
Table of Contents 1
Introduction 2
User Information Warning 4
Dip Switch Settings 5
| C Parts Layout Charts 6
General Wiring Diagram 8
Schematic Diagrams Insert
INTRODUCTION
PANDORA'S PALACE is one of the most complete conversion kits available today. Every detail has been carefully considered, designed and packaged to provide you the means of easily producing a professional conversion. We strongly urge you to FULLY STUDY this instruction manual BEFORE you begin your conversion. It contains step-by-step instructions, schematic diagrams and suggestions on how to assemble PANDORA'S PALACE and maximize your profits. PANDORA'S PALACE can be installed in any vertically mounted rastar scan monitor game — UPRIGHT, MINI, OR COCKTAIL. For converting your cocktail model — dip-switch setting is on printed circuit board, additional wires are included in wiring harness, and two full sets of button/ instruction decals are provided (4 each JUMP and 2 each INSTRUCTION). Everything you will need to construct your new game is provided in this kit* All accessory parts
- wiring harness, joy-stick, etc. are custom made for PANDORA'S PALACE by top engineers experienced in the coin-op industry.
PUTTING YOUR BEST GAME FORWARD
PREPARATION: For best results, all old graphics should be removed completely from the cabinet. “Stick-on” graphics can be removed by using a hairdryer or hot air device. The heat from the dryer will loosen the adhesive, allowing you to easily peel them off — any adhesive residue can be cleaned off with acetone and a soft dry cloth. (DO NOT USE ACETONE ON SURFACES PAINTED WITH FLAT PAINT). TOOLS YOU NEED:
- Foaming Aerosol (such as “Windex’).
- Soft Squeegee (or cardboard).
- X-Acto Knife.
- Rigid Squeegee (included).
one PANEL DECALS:
- Spray area of cabinet where side decals are to be applied with foaming aerosol or a mild soap solution.
- Remove protective backing from decals.
- Position decals into place.
- With a soft squeegee and beginning from the center of the decal, slowly and evenly press out excess foam until you achieve a smooth finish.
- Allow to set approximately 2 to 3 hours before handling. Maximum adherence is achieved in 48 to 72 hours.
3 LAYER CONTROL PANEL OVERLAY (KONAMI/INTERLOGIC EXCLUSIVE)
- Pre-drill control panel for any additional holes needed for joysticks or buttons.
- Pre-position 4 mil. printed vinyl overlay (Roman Columns) prior to removing backing.
- Slowly apply overlay — removing backing as you apply it to the surface. Be sure all air pockets are removed. (Minor air pockets may be popped with a pin). IT IS NOT RECOM- MENDED TO USE FOAMING AEROSOL IN THIS STEP SINCE TWO MORE LAYERS MUST BE APPLIED WHICH WOULD BE ADVERSELY AFFECTED BY ANY MOISTURE LEFT UNDER THE 4 MIL. VINYL OVERLAY.
- Next, position instruction and button decals (1 Player, 2 Player and Jump) where desired on top of 4 mil. vinyl overlay, by peeling off die-cut decals from 6” x 9” decal sheet and applying. Be sure to allow room for button collars.
- Remaining decorative decals are to be used to customize and increase attractiveness of your game.
- Apply the clear 10 mil. suede Lexan sheet (as you did the printed overlay) over the control panel completely covering all decals applied in steps 2 thru 5. DO NOT USE FOAMING AEROSOL OR ANY LIQUID UNDER ANY CIRCUMSTANCES IN THIS STEP!
- Appearance of control panel will now be somewhat cloudy. Using a blow-dryer (set on high) or a hot-air device, heat up Lexan which you have just applied, one section at a time. As you do this, rub down clear suede Lexan (using a very rigid squeegee — included) applying pressure liberally, especially around button/decorative decals. If the contro! panel has been heated enough (it must be hot, not just warm), the result will be a crystal clear control panel.
- Using an X-Acto knife, cut around joystick and button placements. THE KONAMI/INTERLOGIC NEW STYLE CON- TROL PANEL WILL TAKE A LITTLE EXTRA TIME TO APPLY. HOWEVER, THE BETTER YOUR GAME LOOKS, THE MORE IT WILL EARN! THE 3-LAYER KONAMI/INTERLOGIC DESIGNED CONTROL PANEL PREVENTS PLAYERS FROM PEELING IN- STRUCTION/BUTTON DECALS WHICH DEFACES YOUR GAME.
*NOTE: POWER SUPPLY al HAVE +5V 5. +12V 1.0A on 2.0A CURRENT PARAMETERS
MARQUEE
1/8” Acrylic Marquee should cut to fit your game. DO NOT remove protective mask until this is done. One way of cutting your Marquee is as follows: (Be sure to protect painted side of Marquee from any surface which may scratch or mar finish).
CUTTING WITH A KNIFE OR SCRIBER Acrylic sheet up to 3/16” thick may be cut by a method similar to that used for cutting window glass. Use a scriber of some kind — a scribing knife such as the one pictured, a metal scriber, an awl, or even a sturdy craft knife — to score the sheet. Draw the scriber several times (7 or 8 times for a 3/16” thick piece) along a straight edge held firmly in place. It is best not to remove the protective masking. Make the cuts carefully using firm, even pressure. For best results make each stroke cleanly off the edge of the sheet. Then, clamp the acrylic sheet or hold it rigidly under a straight edge with the scribe mark hanging just over the edge of a table. Protect your hands with a cloth, and apply a sharp downward pressure to the other side of the sheet. It will break along the scratch. Scrape the edges to smooth any sharp corners. This method is not recommended for long breaks or thick material.
Always draw the scribing knife along a straight edge. Break sheet over edge of table after scribing.
DIAGNOSTIC PROCEDURES
AUTOMATIC SELF-TEST — Upon “Power On’, this system will automatically test ROMS and VIDEO RAMS. The screen will display pass or fail conditions as follows: ROM OK RAM OK = TEST PASSED
BAD ROM BAD RAM = [EST FAILED
If there is a problem, before contacting your distributor:
- Check that all chips on board and wiring connections are tight.
- Check output from power supply at the board. (Do not just check at the power supply as voltage drops may occur over the length of the wire.) MANUAL TEST — A more detailed six-step diagnostic may be performed by depressing the One and Two Player Start Buttons simultaneously during power turn on. When the “cross-hatch” pattern appears, release the buttons and proceed as follows: 1 “CROSS-HATCH” PATTERN — When “crosshatch” is displayed, adjustments to the monitor may be needed for proper picture. Horizontal and Vertical size controls should be adjusted so that the borders of “cross-hatch” extend to the borders of the picture tube. Color and brightness should be adjusted for white lines and black background. 2 COLOR TEST — From “cross-hatch” pattern, press One Player Start and the screen will display sixteen color blocks. If a block shows any irregularities (e.g., lines or dots in color blocks), this could be due to a failure of VIDEO RAM, COLOR RAM, or OBJ CIRCUITS. Use these blocks to further adjust monitor focus and colors. 3 SWITCH TEST — From color test, press One Player Start and the screen will display all switches with a zero (0) to the right. When a switch is activated the zero (0) should change to a one (1). 4 COIN COUNTER TEST — From switch test, press One Player Start and the screen will display “coin counter’. While number one (1) is shown, counter one should pulse eight times. When number two (2) is shown, counter two should pulse eight times and the screen will automatically advance to the next test. 5 DIP SWITCH SETTINGS — From coin counter test, the screen will automatically display all programmable features with their respective settings. These settings should correspond to the position of the dip switches. 6 SOUND TEST — From dip switch settings, press One Player Start. The screen will automatically display one of thirty-four sound codes every eight seconds (in a hexidecimal sequence), with a different sound produced for each. To cycle the codes, quickly, use Two Player Start. TO EXIT DIAGNOSTICS — TURN POWER OFF AND ON.
PANDORA’S PALACE DIP SWITCH SETTINGS:
A. DIP 1 SWITCH SETTING FIG. 1. — COIN 1 SW SETTING / COIN 2 SW SETTING COIN 1 SW SETTING COIN 2 SW SETTING
| sw] | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | COIN | PLAY |
| OFF | OFF |OFF |OFF | OFF | OFF |OFF | OFF | 1 | 1 | ||||||||
| ON | OFF | ON | OFF | 1 | 2 | |||||||
| OFF | ON | OFF | ON | 1 | 3 | |||||||
| ON | ON | ON | ON | 1 | 4 | |||||||
| OFF | OFF | ON | [OFF | OFF | OFF | ON | OFF | 1 | 5 | |||||||
| ON | OFF | ON | OFF | 1 | 6 | |||||||
| OFF | ON | OFF | ON | 1 | 7 | |||||||
| ON | ON | ON | ON | 2 | 1 | |||||||
| OFF | OFF |OFF | ON | OFF | OFF |OFF | ON | 2 | 3 | |||||||
| ON | OFF | ON | OFF | 2 | 5 | |||||||
| OFF | ON | OFF | ON | 3 | 1 | |||||||
| ON | ON | ON | ON | 3 | 2 | |||||||
| OFF | OFF | ON | ON | OFF | OFF | |ON | ON | 3 | 4 | ||||||
| ON | OFF | ON | OFF | 4 | 1 | |||||||
| OFF | ON | OFF | ON | 4 | 3 | |||||||
| ON | ON | ON | ON | FREE PLAY 1-4 |
B. DIP 2 SWITCH SETTINGS
FIG. 1. — THE NUMBER OF PLAYERS
| SW | 1 | 2 | NUMBER |
| 0 | OFF OFF | 3 |
ON | OFF 4 OFF | ON 5 ON | ON 7
FIG. 2. — SWITCH FOR CHANGE OF TABLE OR UPRIGHT
sw] 3 TYPE OFF TABLE-USING I/O FOR 1 OR 2 PLAYER
| 0 | {ON | UPRIGHT-USING I/O FOR 1 PLAYER ONLY |
FIG. 3. — BONUS SETTING
| sw | 4 | 5 | BONUS PLAYER |
| 0 | OFF | OFF | Ast as 20,000 points |
2nd as 80,000 points and every 60,000 points ON | OFF 1st as 30,000 points 2nd as 100,000 points and every 70,000 points OFF | ON only 20,000 points ON | ON only 30,000 points FIG. 4. — DIFFICULTY OF THE GAME
| sw | 6 | 7 | DIFFICULTY |
OFF | OFF |_ 1 EASY
| QO | ON | |OFF| | 2 |
OFF| ON | 3 ON | ON | 4 DIFFICULT
FIG. 5. — MUSIC IN ATTRACT MODE
SW] 8 | MUSIC IN ATTRACTIVE MODE OFF OFF 0 | ON ‘ON
PANDORA’S PALACE: 1 C Parts Layout Chart
| iC) | 9 | ® | 9 | |
| ls DS245 | + UUS273 | 15272 | + | 301 |
| a | , | 27641528 ® a |
IKX@ F105
| aH | 7 + | ; | = | ||
| So77 | iige7 J+ [ | T22é1 ale | |||
| + Used: | (26x15) | Ce 8 | |||
| =; | Rar 250F | S273 | a | ||
| @+ee | er) | + Ws CE | 3* | C | TR2ET AE ve, |
| I | & | 2764) x08 ore | |||
| i | 503 | ———— | |||
| @+ aaa | (S377 | TLSEE | ve 1ST) | Sy | |
| j | tSEZ | x | sg, | oO | # |
~ @8F (Wo USE) @
| fo) . Wea) 5367) | 13157} YiS8S JF LSI6F ok SES 163. + | 3) |
OB) x 2764 38 las}
| ® A | S2J+ Tye. wet | FY |
Sane
- ) 2128 ‘
| * 3M | 2 pag | 2164 [ge OL® | ||
| S ) 2128 | 082 | uusizd | eiso4_} + 5 | =) |
(328)
| 502 | - | 2764 | ® |
| ®, | sez | vy USGE J+ | is * |
oes IKxe
| © D2 | > | £800 | a | 328) | © |
| 3 | Toad | + | ») 2264 oq! D |
=. et
| * SUSE | i | usecase | ~ | aC) | |
| Om | mw =. | {{ | tage Ge. |_ See | OF | w& |
nN
| @ | a | 4.7K X 6 | ||||
| + UST | PIEYZI | 1S04_] | VST | 06374] | 4IKX6 | oS |
| al | = | i | ||||
| + UST) | S00 | US 74 | L510 | Ki? | ii | 6 |
| ® | es7a | 68A0IE © ct 2764 iz] | +O | |||
| 1 @+iser + GM | A | ; | : | © |
: ) $04 Do |, aos
| ©) + USM) = USE) + Us25T | SB + WS | +© |
sauay a
- Geeks i + (Sar cis2e4 J
| | | HIRE | Ge User) | |
| : | g | > | |
| : | © u | @rg | “) |
; 3 ‘ iS) 40P CONNEC TOR
- NOTES —~ L CERAMIC CAPACITOR + ELECTROLITIC CAPACITOR 2 MYLAR CAPACITOR
(Sit UC SOCKEL TONG MARK : Oly CERAMIC CAPACITOR (J: Rom cagee numer ¢ \ J ): NO RAYOUT PARTS A "A" THROUGH "2"
TOP VIEV
a * "A" THROUGH oe ROM LABEL NUMBER S NOMARK © Oty CERAMIC CAPACITOR = 1C socker © + CERMIC CAPACITOR m LECTLYTIC CAPACITOR MILAR CAPACITOR NOTES ; ts 02 qe
ose |
at 470PO© 4 aty ©
pos Dus 74 10K wa may Sus 367 dis 08 | 7 _ _ de 4b ox 401
Sis ae
we 470 4
a b DIP Sw 3 dh 402 Ae
Ook
ar £ DIP Swit Joy 144460
2aKKE R-ARRY 1
Dik Sw2 i BERIG R-ARRY
Des 367 @roorase os
decoo ei ero fe ® FE? aw or A bb 25¥1000p
40P CONNECIOR at @ar0 i i dh
LAI a
rovz20p er Im SV CONNECTOR
1 C Parts Layout Chart
TOP VIEW
PANDORA’S PALACE
SPEAKERS
enow BA BLU WEL IDV Bn Ore eT SPEAKER OUT
ow 2) SPEAKER OUT
5-5 _2P_SHOOT GRN w/WHT 3] 2p JUMP *
oS 2p RIGHT BROWN. ae YELwiGAN C1, 2P RIGHT ¥ us 2P LEFT®
SoS 2p SLRT 1 BRN WiGRN se P_ START. BRN W/WHT 4 ol 5 oP UP. WHT W/YEL 2P UP
5 _ SERVICE BRN W/BLU 5S 1p shoo YEL WIBLK IP LEFT WHT wiGRN ate RIGHT. WHT W/ORG 3 > —2P_ DOW. RED W/BLK op up ReDwiwaT 1, 2P Down
Olly BLU WIBRN | ‘Ol | COIN2 CONE GRN WIBLU “51 COW 1P DOWN Sey pt COUNTER _WHTWIBBN T7T_ COIN COUNTER | 7] iP DOWN pontiooy _| MOLET 7 COIN COUNTER 2
INTER,
SERVICE
iP JUMP IP LEFT IP RIGHT
PANDORA’S PALACE:
BLUE
woe : BI ave FAN moTOR ALUE_} 20bE 1000 A GREEN 13] GREEN Sint
REN. ( ira pe (a) RED BLK FG cn GND GND GND +5V +5V
~ NOISE, AC_100V.
240 FILTER TRANS
220V 3A FORMER POWER SUPPLY
He JO0V FUSE 24\ nee ti2y 24-3 N94
re &
=I (“au | a Power OV tEsv gab o\ 554 FS SOLDER SIDE SW ov BIS PARTS SIDE CONNECTOR KEL- 1168 -036-009 General Wiring Diagram
- Table type only
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
eiger ra a, p £8041 s32% ae "Med! aT [a
x
SLSESRss er\e|era 10.
Cae Mn
i ” CS} ¢s G0 ey ey DNF xe —2| ors —3| ‘ats Hi “DXF 3 Lad 2 =a Ms “XO ak oa
3 sa be
- ta 4H A fos ES loopr2 Li , aa SEAS
| zt | i | XB 19 | ae | i |
| teil a | ‘ | 16) | ||
| ae Ale | a | 5 | ||
| aed | BL | fy |
ald LI beste 4 ; tse se =e se fer Dou
| Seale | | Hote | pL -tS08, |
Ho] E5164 py. 27 aria LACH
a2 a3 ae a mm 1 @ 8 Je ee 5° 220, G L™ fT OS " Lb ayeze T* rm c R 1 yw IK is —nore D; sv-conwector-2e QGFLATCABLE CONNECTOR 40P Q@IMLER ‘caPactTOR ©5ELECTROLITIC CAPACITOR NOMARKE | CERAMIC CAPACITOR pivee sv Lino ov
is €12 ae Konami/interlogic ©1984
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.