CATHODE RAY TOMES

Wild Riders STD

Wild Riders (Wow Entertainment / Sega, 2001) · Manual · 105 pages · 134 sections · original scan

Page 1

MANUAL NO. 999-1149 STD TYPE

Owner’s Manual

(uy)

SEGA ENTERPRISES, INC. USA S 1ST PRINTING FEB.01

Page 2

Warranty

Your new Sega Product is covered for a period of 90 days from the date of shipment. This certifies that the Printed Circuit Boards, Power Supplies and Monitor are to be free of defects in workmanship or materials under normal operating conditions. This also certifies that all Interactive Control Assemblies are to be free from defects in workmanship and materials under normal operating conditions. No other product in this machine is hereby covered.

Sellers sole liability in the event a warranted part described above fails shall be, at its option, to replace or repair the defective part during the warranty period. For Warranty claims, contact your Sega Distributor.

Should the Seller determine, by inspection that the product was caused by Accident, Misuse, Neglect, Alteration, Improper Repair, Installation or Testing, the warranty offered will be null and void.

Under no circumstances is the Seller responsible for any loss of profits, loss of use, or other damages.

This shall be the exclusive written Warranty of the original purchaser expressed in lieu of all other warranties expressed or implied. Under no circumstance shall it extend beyond the period of time listed above.

Page 3

BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWING: To maintain the safety:

To ensure the safe usage of the product, be sure to read the following before using the product. The following instructions are intended for the users, operators and the personnel in charge of the operation of the product. After carefully reading and sufficiently understanding the warning displays and cautions, handle the product appropriately. Be sure to keep this manual nearby the product or elsewhere convenient for referring to it when necessary.

Herein, explanations which require special attention are enclosed with dual lines. Depending on the potentially hazardous degrees, the terms of WARNING, CAUTION, etc. are used. Be sure to understand the contents of the displays before reading the text.

Indicates that mishandling the Indicates that mishandling the product product by disregarding this by disregarding this caution will cause

warning will cause a potentially a slight hazardous situation which can
WARNING! hazardous situation which can CAUTION! result in personal injury and or material result in death or serious injury. damage.

For the sage usage of the product, the following pictographs are used:

Indicates “HANDLE WITH CARE.” In order to protect the human body an equipment, this display is attached to places where the Owner’s Manual and or Service Manual should be referred to.

© Perform work in accordance with the instructions herein stated. Instructions for work are explained by paying attention to the aspect of accident prevention. Failing to perform work as per the instructions can cause accidents. In the case where only those who have technical expertise should perform the work to avoid hazardous situation, the instructions herein state that the serviceman should perform such work.

© Be sure to turn off power before working on the machine. To prevent electric shock, be sure to turn off power before starting the work in which the worker touches the interior of the product. If the work is to be performed in the power-on status, the Instruction Manual herein always states to that effect.

O Besure to ground the Earth Terminal (this, however, is not required in the case where a power cord with earth is used). This product is equipped with the Earth Terminal. When installing the product, Connect the Earth Terminal to the “accurately grounded indoor earth terminal” by using an earth wire. Unless the product is grounded appropriately, the user can be subject to electric shock. After performing repair, etc. for the Control equipment, ensure that the Earth Wire is firmly connected to the Control equipment.

© Ensure that the Power Supply used is equipped with an Earth Leakage Breaker. This product does not incorporate the Earth Leakage Breaker. Using a power supply which is not equipped with the Earth Leakage Breaker can cause a fire when earth leakage occurs.

© Be sure to use fuses which meet the specified rating. (only for the machines which use fuses). Using fuses exceeding the specified rating can cause a fire and electric shock.

Page 4

© _ Specification changes (removal of equipment, conversion and addition) not designated by SEGA are not allowed. The parts of the product include warning labels for safety, covers for personal protection, etc. It is very hazardous to operate the product by removing parts and or modifying the circuits. Should doors, lids and protective parts be damaged or lost, refrain from operating the product, and contact where the product was purchased from or the office herein stated. SEGA shall not be held responsible for any accidents, compensation for damage to a third party, resulting from the specifications not designated by SEGA. ©. Ensure that the product meets the requirements of appropriate Electrical Specifications. Before installing the product, check for Electrical Specifications. SEGA products have a nameplate on which Electrical Specifications are described. Ensure that the product is compatible with the power supply voltage and frequency requirements of the location. Using any Electrical Specifications different from the designated Specifications can cause a fire and electric shock. © _ Install and operate the product in places where appropriate lighting is available, allowing warning labels to be clearly read. To ensure safety for the customers, labels and printed instructions describing potentially hazardous situation are applied to places where accidents can be caused. Ensure that where the product is operated has sufficient lighting allowing the warnings to be read. If any label is peeled off, apply it again immediately. Please place an order with where the product was purchased from or the office herein stated. © When handling the Monitor, be very careful. (Applies only to the product w/monitor.) Some of the monitor (TV) parts are subject to high tension voltage. Even after running off power, some portions are still subject to high tension voltage sometimes. Monitor repair and replacement should be performed only be those technical personnel who have knowledge of electricity and technical expertise. © Besure to adjust the monitor (projector) properly. (Applies only to the product w/monitor.) Do not operate the product leaving on-screen flickering or blurring as it is. Using the product with the monitor not properly adjusted may cause dizziness or a headache to an operator, a player, or the customers. © _ When transporting or reselling this product, be sure to attach this manual to the product. In the case where commercially available monitors and printers are used in this product, only the contents relating to this product are explained herein. Some commercially available equipment has functions and reactions not stated in this manual. Read this manual together with the specific Instruction Manual of such equipment.

  • Descriptions herein contained may be subject to improvement changes without notice. © The contents described herein are fully prepared with due care. However, should any question arise or errors be found, please contact SEGA.

INSPECTIONS IMMEDIATELY AFTER TRANSPORTING THE PRODUCT TO THE LOCATION.

Normally, at the time of shipment, SEGA products are in a status allowing for usage immediately after transporting to the location. Nevertheless, an irregular situation may occur during transportation. Before turning on power, check the following points to ensure that the product has been transported in a satisfactory status. Are there any dented portions or defects (cuts, etc.) on the external surfaces of the cabinet? Are Casters and Adjusters, damaged? Do the power supply voltage and frequency requirements meet with those of the location? Are all wiring connectors correctly and securely connected? Unless connected in the correct direction, connector connections can not be made accurately. Do not insert connectors forcibly. Do power cords have cuts and dents? Do the fuses used meet specified rating? Is the Circuit Protector in an energized status? Are all accessories available? Can all Doors and Lids be opened with the Accessory keys? Can Doors and Lids be firmly closed?

Page 5

TABLE OF CONTENTS

BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWING: TABLE OF CONTENTS

INTRODUCTION OF THE OWNER’S MANUAL

. HANDLING PRECAUTIONS .... see

. PRECAUTIONS CONCERNING INSTALLATION LOCATION

. OPERATION ....

. ACCESSORIES

. ASSEMBLING AND INSTALLATION

  • PRECAUTIONS TO BE HEEDED WHEN MOVING THE MACHINE

. CONTENTS OF GAME

  • EXPLANATION OF TEST AND DATA DISPLAY

8-1 SWITCH UNIT AND COIN METER

8-2 SYSTEM TEST MODE...

8-3 GAME TEST MODE

  • CONTROL PANEL ARwWNS

x

9-1 ADJUSTING/REPLACING THE HANDLBAR VOLUME... 45-47

9-2 ADJUSTING/REPLACING THE ACCELERATOR VOLUME 48

9-3 REPLACING THE CONTROL STICK’S MICROSWITCH 49

9-4 GREASING 50 - 53

9-5 REPLACING THE SPRING 54

  • REAR BRAKE... 55-58

10 - 1 REMOVING THE BRAKE UNIT... 55-56

10 - 2 ADJUSTING/REPLACING THE REAR BRAKE VOLUME . 56

10-3 GREASING 57-58

  • MONITOR ... sess 59-61 11-1 CAUTIONS AND WARNINGS CONCERNING THE SAFETY FOR HANDLING THE MONITORS, 59-61

11 -2 CAUTIONS TO BE HEEDED WHEN CLEANING THE CRT SURFACES 61

  • COIN SELECTOR ..... 62 - 66
  • PERIODIC INSPECTION TABLE 67
  • TROUBLESHOOTING .... 68-71
  • GAME BOARD eee 72-76

15 - 1 TAKING OUT THE GAME BOARD . 72-73

15 - 2 COMPOSITION OF GAME BOARD... 74

15-3 REPAIR/SERVICING AND CARTON BOX 75-76

  • DESIGN RELATED PARTS 77
  • PARTS LIST .... 78 - 95
  • WIRE COLOR CODE TABLE 96
  • WIRING DIAGRAM ..... 97 - 98
Page 6

SPECIFICATIONS Length : 74 inches Height : 65 inches. Width :31 inches Weight : Approx. 400 Ibs.

MONITOR : 29 INCH COLOR MONITOR,

INTRODUCTION OF THE OWNERS MANUAL

This Owner's Manual is intended to provide detailed descriptions together with all the necessary information covering the general operation of electronic assemblies, electromechanicals, servicing control, spare parts, etc. as regards the product, WILD RIDER STD TYPE. This manual is intended for the owners, personnel and managers in charge of operation of the product. Operate the product after carefully reading and sufficiently understanding the instructions. If the product fails to function satisfactorily, nontechnical personnel should under no circumstances touch the internal system. Please contact where the product was purchased from.

Use of this product is unlikely to cause physical injuries or damages to property. However, where special attention is required this is indicated by a thick line, the word "IMPORTANT" and its sign in this manual.

Indicates that mishandling the product by disregarding this display can cause the product's intrinsic performance not to be obtained, resulting in malfunctioning.

MPORTANT

SEGA ENTERPRISES, INC. (U.S.A.)/CUSTOMER SERVICE 45133 Industrial Drive, Fremont, California 94538, U.S.A. Phone : (415) 701-6580 Fax : (415) 701-6594

Page 7

DEFINITION OF LOCATION MAINTENANCE MAN AND SERVICEMAN

WARNING! Non-technical personnel who do not have technical knowledge and expertise should refrain from performing such work that this manual requires the location's maintenance man or a serviceman to carry out, or work which is not explained in this manual. Failing to comply with this instruction can cause a severe accident such as electric shock.

Ensure that parts replacement, servicing & inspections, and troubleshooting are performed by the location's maintenance man or the serviceman. It is instructed herein that particularly hazardous work should be performed by the serviceman who has technical expertise and knowledge.

The location's maintenance man and serviceman are herein defined as follows:

"Location's Maintenance Man" : Those who have experience in the maintenance of amusement equipment and vending machines, etc., and also participate in the servicing and control of the equipment through such routine work as equipment assembly and installation, servicing and inspections, replacement of units and consumables, etc. within the Amusement Facilities and or locations under the management of the Owner and Owner's Operators of the product.

Activities of Location's Maintenance Man : Assembly & installation, servicing & inspections, and replacement of units & consumables as regards amusement equipment, vending machines, etc.

Serviceman : Those who participate in the designing, manufacturing, inspections and maintenance service of the equipment at an amusement equipment manufacturer. Those who have technical expertise equivalent to that of technical high school graduates as regards electricity, electronics and or mechanical engineering, and daily take part in the servicing & control and repair of amusement equipment.

Serviceman's Activities : Assembly & installation and repair & adjustments of electrical, electronic and mechanical parts of amusement equipment and vending machines.

LISTED

5K92 ®

AMUSEMENT MACHINE

Page 8
  • HANDLING PRECAUTIONS

When installing or inspecting the machine, be very careful of the following points and pay attention to ensure that the player can enjoy the game safely. Non-compliance with the following points or inappropriate handling running counter to the cautionary matters herein stated can cause personal injury or damage to the machine.

@ Before performing work, be sure to turn power off. Performing the work without turning power off can cause an electric shock or short circuit. In the

WARNING! case work should be performed in the status of power on, this manual always states to that effect. To avoid electric shock or short circuit, do not plug in or unplug quickly. To avoid electric shock, do not plug in or unplug with a wet hand. Do not expose Power Cords and Earth Wires on the surface, (floor, passage, etc.). If exposed, the Power Cords and Earth Wires are susceptible to damage. Damaged cords and wires can cause electric shock or short circuit.

To avoid causing a fire or electric shock, do not put things on or damage

Power Cords. When or after installing the product, do not unnecessarily pull the power cord. f damaged, the power cord can cause a fire or electric shock. n case the power cord is damaged, ask for replacement through where the product was purchased from or the office herein stated. Using the cord as is damaged can cause fire, electric shock or leakage. Be sure to perform grounding appropriately. Inappropriate grounding can cause an electric shock. Be sure to use fuses meeting specified rating. Using fuses exceeding the specified rating can cause a fire or electric shock. Completely make connector connections for IC BD and others. Insufficient insertion can cause an electric shock. Specification changes, removal of equipment, conversion and/or addition, not designated by SEGA are not permitted.

Failure to observe this may cause a fire or an electric shock. Non-compliance

with this instruction can have a bad influence upon physical conditions of the players or the lookers-on, or result in injury during play. SEGA shall not be held responsible for damage, compensation for damage to a third party, caused by specification changes not designated by SEGA. Be sure to perform periodic maintenance inspections herein stated.

Page 9

IMPORTANT

For the IC board circuit inspections, only the logic tester is allowed. The use of a multiple-purpose tester is not permitted, so be careful in this regard. When cleaning the CRT surfaces, use a soft, dry cloth. Do not apply chemicals such as thinner, benzine, etc. The electronic parts on the IC Board could be damaged due to human body's static electricity. Before performing IC Board related work, be sure to discharge physically accumulated statics by touching grounded metallic surfaces, etc. Some parts are the ones designed and manufactured not specifically for this game machine. The manufacturers may discontinue, or change the specifications of, such general-purpose parts. If this is the case, Sega cannot repair or replace a failed game machine whether or not a warranty period has expired.

Page 10
  • PRECAUTIONS CONCERNING INSTALLATION

LOCATION

  • This product is an indoor game machine. Do not install it outside. Even indoors, avoid installing in places mentioned below so as not to cause a fire, electric shock, be GI injury and or malfunctioning. : aces subject to rain or water leakage, or places subject to high humidity in P the proximity of an indoor swimming pool and or shower, etc. Places subject to direct sunlight, or places subject to high temperatures in the proximity of heating units, etc. Places filled with inflammable gas or vicinity of highly inflammable/volatile chemicals or hazardous matter. Dusty places. Sloped surfaces. Places subject to any type of violent impact. Vicinity of anti-disaster facilities such as fire exits and fire extinguishers. The operating (ambient) temperature range is from 5 Celsius to 40 Celsius. Only in the case a projector is employed, the temperature range is from 5 Celsius to 30 Celsius.

LIMITATIONS OF USAGE REQUIREMENTS

Be sure to check the Electrical Specifications. Ensure that this product is compatible with the location's power supply,

WARNING! voltage and frequency requirements. A plate describing Electrical Specifications is attached to the product.

Non-compliance with the Electrical Specifications can cause a fire and This product requires the Breaker and Earth Mechanisms as part of the location facilities. Using them in a manner not independent can cause a fire

electric shock.

and electric shock. Ensure that the indoor wiring for the power supply is rated at 7A or higher (AC single phase 100 ~ 120V area), and 4A or higher (AC 220 ~ 240V area).

electric shock. Be sure to independently use the power supply equipped with the Earth Leakage Breaker. Using a power supply without the Earth Leakage Breaker can cause an outbreak of fire when earth leakage occurs. Putting many loads on one electrical outlet can cause generation of heat and a fire resulting from overload. When using an extension cord, ensure that the cord is rated at 7A or higher (AC 100 ~ 120V area) and 4A or higher (AC 220 ~ 240V area). Using a cord rated lower than the specified rating can cause a fire and electric shock.

Page 11

OPERATION AREA

A

WARNING!

IMPORTANT

MAX MAX MAX MAX MAX MAX MAX MAX MAX

@ For the operation of this machine, secure a minimum area of 1.3m (W) X

1.6m (D). during gam n order to prevent injury resulting from the falling down accident e play, be sure to secure the minimum area for operation. Be sure to provide sufficient space so as to allow this product's ventilation fan to function place any ol SEGA shal.

efficiently. To avoid machine malfunctioning and a fire, do not

stacles near the ventilation opening. not be held responsible for damage, compensation for damage to a third party, resulting from the failure to observe this instruction.

. 3.66 A (AC 110V 50 Hz) _3.57 A (AC 110V 60 Hz) 25 A(AC 120V 60 Hz) A (AC 220V 50 Hz) A (AC 220V 60 Hz) A (AC 230V 50 Hz) A (AC 230V 60 Hz) A (AC 240V 50 Hz) A (AC 240V 60 Hz) MAX. 3.70 A (For TAIWAN) <1 2.

6: For transporting the machine into the location's building, the minimum necessary

dimensions of tl

  • Electric current consumption —S e opening (of doors, etc.) are 0.8m(W) and 1.8m(H).
Page 12
  • OPERATION

PRECAUTIONS TO BE HEEDED BEFORE STARTING THE OPERATION

To avoid injury and trouble, be sure to constantly give careful attention to the behavior and manner of the visitors and players.

A In order to avoid accidents, check the following before starting the operation: @ To ensure maximum safety for the players and the customers, ensure that

WARNING! where the product is operated has sufficient lighting to allow any warnings to be read. Operation under insufficient lighting can cause bodily contact with each other, hitting accident, and or trouble between customers. Be sure to perform appropriate adjustment of the monitor (projector). For operation of this machine, do not leave monitor's flickering or deviation as is. Failure to observe this can have a bad influence upon the players’ or the customers' physical conditions. It is suggested to ensure a space allowing the players who feel sick while playing the game to take a rest. Check if all of the adjusters are in contact with the surface. If they are not, the Cabinet can move and cause an accident.
Page 13

@ Do not put any heavy item on this product. Placing any heavy item on the product can cause a falling down accident or parts damage.

WARNING! Do not climb on the product. Climbing on the product can cause falling down : accidents. To check the top portion of the product, use a step. To avoid electric shock, check to see if door & cover parts are damaged or omitted. To avoid electric shock, short circuit and or parts damage, do not put the following items on or in the periphery of the product. Flower vases, flowerpots, cups, water tanks, cosmetics, and receptacles/ containers/vessels containing chemicals and water.

crowded situation at the installation location. Insufficient installation space can cause making bodily contact with each other, hitting accidents, and or trouble between customers. A To avoid injury, be sure to provide sufficient space by considering the potentially

CAUTION!

PRECAUTIONS TO BE HEEDED DURING OPERATION (PAYING ATTENTION TO CUSTOMERS)

To avoid injury and trouble, be sure to constantly give careful attention to the behavior and manner of the visitors and players.

nN @ To avoid injury and accidents, those who fall under the following categories are not allowed to play the game.

WARNING! Those who need assistance such as the use of an apparatus when walking. Those who have high blood pressure or a heart problem. Those who have experienced muscle convulsion or loss of consciousness when playing video game, etc. Those who have a trouble in the neck and or spinal cord. Intoxicated persons. Pregnant women or those who are in the likelihood of pregnancy. Persons susceptible to motion sickness. Persons whose act runs counter to the product's warning displays. A player who has never been adversely affected by light stimulus might experience dizziness or headache depending on his physical condition when playing the game. Especially, small children can be subject to those conditions. Caution guardians of small children to keep watch on their children during play. Instruct those who feel sick during play to have a medical examination. To avoid injury resulting from falling down and electric shock due to spilled drinks, instruct the player not to place heavy items or drinks on the product. To avoid electric shock and short circuit, do not allow customers to put hands

and fingers or extraneous matter in the openings of the product or small

openings in or around the doors. To avoid falling down and injury resulting from falling down, immediately stop the customer's leaning against or climbing on the product, etc.

Page 14
WARNING!

A

CAUTION! To avoid electric shock and short circuit, do not allow the customers to unplug the power plug without a justifiable reason.
Caution lookers-on so as not to touch the operating unit while in play. Failure to observe this may cause bodily contact with the player and trouble between the customers.

Immediately stop such violent acts as hitting and kicking the product. Such violent acts can cause parts damage or falling down, resulting in injury due to fragments and falling down.

Persons other than the player must not touch the device during play. If this is violated, their hands or fingers may be pinched by the handlebar, causing them to be injured.

Instruct the player to watch his/her step when getting on the Floor Base so as to avoid stumbling over.

Page 15
  • ACCESSORIES

When transporting the machine, make sure that the following parts are supplied.

TABLE 4 ACCESSORIES

CARTON BOX 601-11044 (1) TAMPERPROO WRENCH Used for transporting the Game Board. M4 540-0006-01 (1) Refer to 15-3. M6 540-0015-01 (1) we TOOL

Page 16
  • ASSEMBLING AND INSTALLATION
WARNING!
CAUTION! Perform assembly work by following the procedure herein stated. Failing to comply with the instructions can cause electric shock hazard. Perform assembling as per this manual. Since this is a complex machine, erroneous assembling can cause an electric shock, machine damage and or not functioning as per specified performance. When assembling, be sure to use plural persons. Depending on the assembly work, there are some cases in which working by one person alone can cause personal injury or parts damage. Ensure that connectors are accurately connected. Incomplete connections can cause electric shock hazard. Be careful so as not to damage wirings. Damaged wiring can cause electric shock and short circuit hazards. This work should be performed by the Location's Maintenance Man or Serviceman. Performing work by non-technical personnel can cause a severe accident such as electric shock. Failing to comply with this instruction can cause a severe accident such as electric shock to the player during operation. Provide sufficient space so that assembling can be performed. Performing work in places with narrow space or low ceiling may cause an accident and assembly work to be difficult. To perform work safely and avoid serious accident such as the cabinet's falling down, do not perform work in places where step-like grade differences, a ditch, or slope exist.

When handling plastic parts, use care. Do not give a shock or apply excessive load to the fluorescent lamps and plastic parts. Failure to observe this can cause parts damage, resulting in injury due to fragments, cracks and broken pieces. To perform work safely and securely, be sure to prepare a step which is in a secure and stable condition. Performing work without using the step can cause violent falling down accidents.

Page 17

When carrying out the assembling and installation, follow the following 5-item sequence.

1 |SECURING IN PLACE (ADJUSTER ADJUSTMENT)

2 |REMOVING THE SHIPPING BRACKET

3 |POWER SUPPLY, AND EARTH CONNECTION

4 |TURNING POWER ON

5 |ASSEMBLY CHECK

Page 18

SECURING IN PLACE (ADJUSTER ADJUSTMENT)

cabinet can move and cause an accident.

This product has 2 Adjusters at the bottom front part of cabinet and 4 Casters in the rear. When the installation position is determined, let the Adjusters make direct contact with the floor and adjust to ensure the product position is level.

Move the product to the CASTERS

installation position.

@ Let the Adjusters make contact

with the floor. Adjust the height of the 2 Adjusters by using a wrench to ensure the product position is level. If the floor surfaces are level, the product will be level when the front casters are raised =), approximately 7mm above the = floor. ADJUSTERS

ADJUSTER

_ FIG. 5.4a BOTTOM VIEW

Approx.7mm

Have adjusters make contact / with the floor. ure that the 2 Rear Casters are / \in contact with the surface (floor).

FIG. 5.4b ADJUSTER

Page 19

REMOVING THE SHIPPING BRACKET

The mechanism of equipment is fastened for transportation at shipping. Remove the shipping bracket and screws.

Remove the front lid (see Section 9-1).

Remove the front lid (see Section 9-1) @Take out the 2 screws and remove the shipping braket. (FIG. 5. 5)

MECHA SHIPPING BRKT

SCREW (2), M4 X 8, wiflat & spring washers FIG. 5.5

Page 20

3 POWER SUPPLY, AND EARTH CONNECTION

Earth Leakage Breaker. Using a power supply without an Earth Leakage

WARNING! Breaker can cause a fire when electric leakage occurs. Ensure that the "accurately grounded indoor earth terminal" and the earth wire cable are available (except in the case where a power cord plug with earth is used). This product is equipped with the earth terminal. Connect the earth terminal and the indoor earth terminal with the prepared cable. If the grounding work is not performed appropriately, customers can be subjected to an electric shock, and the product's functioning may not be stable. Ensure that the power cord and earth wire are not exposed on the surface (passage, etc.). If exposed, they can be caught and are susceptible to damage. If damaged, the cord and wire can cause electric shock and short circuit accidents. Ensure that the wiring position is not in the customer's passage way or the wiring has protective covering. After wiring power cord on the floor, be sure to protect the power cord. Exposed power cord is susceptible to damage and causes an electric shock accident.

Ay Be sure to independently use the power supply socket outlet equipped with an

The AC Unit is mounted on the rear of the machine. The AC Unit has Main SW, Circuit Protector, Earth Terminal and the Inlet which connects the Power Cord.

@nsure that the Main SW is OFF.

Main SW off } /

/ [EARTH TERMINAL / Connect with the _— L 2 | indoor earth terminal. ea: D> /MAIN SW

FIG. 5.6a AC unit

Page 21

TURNING POWER ON

In this product, the Main SW is in the AC

Unit and the SUB POWER SW is inside

the SERVICE DOOR. The power is not turned on unless the above two switches are on. When the power is turned on, the two fluorescent lamps inside light up, images are outputted on the monitor, and the Advertise mode appears on the

screen. Once the power is turned off, the inserted coin(s) less than one credit and the BONUS ADDER data are cleared. Image output on the monitor. Fluorescent lamps

SUB POWER SW.

5 ASSEMBLY CHECK

In the TEST MODE, ascertain that the assembly has been made correctly and IC BD. is satisfactory (refer to Section 8). In the test mode, perform the following test:

  • MEMORY TEST

Selecting the RAM TEST on the system test mode menu screen causes the on-board memory to be tested automatically. The game board is satisfactory if the display beside each IC No. shows GOOD.

RAM TEST

TESTING NOW

IC29 GOOD 1C35 GOOD Ic09 GOOD IC10 GOOD IC11 GOOD 1IC12 GOOD IC16 GOOD IC18 GOOD IC20 GOOD 1C22 GOOD IC17 GOOD IC19 GOOD IC21 GOOD 1C23 GOOD IC106 GOOD 1IC107 GOOD IC108 GOOD IC109 GOOD IC111 GOOD 1IC113 GOOD IC115 GOOD 1IC117 GOOD IC112 GOOD 1IC114 GOOD IC116 GOOD IC118 GOOD

PRESS TEST BUTTON TO EXIT Emits sounds.

  • C.R.T. TEST

In the system test mode menu, selecting C.R.T. TEST allows the screen (on which the monitor is tested) to be displayed.

C.R.T. TEST 1/2

RED

GREEN

BLUE

WHITE

PRESS TEST BUTTON TO CONTINUE

C.R.T. TEST 2/2

PRESS TEST BUTTON TO EXIT [}

Page 22
  • SOUND TEST

SOUND TEST

RIGHT SPEAKER OFF LEFT SPEAKER OFF -> EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

  • INPUT TEST

INPUT TEST

HANDLEBAR 80 ACCELERATOR 00 FRONT BRAKE 00 REAR BRAKE 00 PUSH OFF PULL OFF START OFF SERVICE OFF TEST OFF

PRESS TEST AND SERVICE BUTTON TO EXIT

  • OUTPUT TEST

OUTPUT TEST

START BUTTON LAMP OFF

->EXIT

SELECT WITH SERVICE BU’ AND PRESS TEST BUTTON TON In the system test mode, selecting SOUND TEST causes the screen (on which sound related BD and wiring connections are tested) to be displayed. Check if the sound is satisfactorily emitted from each speaker and the sound volume is appropriate.

Selecting the INPUT TEST on the game test mode menu screen causes the screen (on which each switch is tested) to be displayed. Press each switch. If the display beside each switch indicates "ON," the switch and wiring connections are satisfactory.

Select OUTPUT TEST from the menu in the game test mode to cause the screen (on which each lamp and wiring connections are tested) to appear. Ensure that lamp light up satisfactorily.

Perform the above inspections also at the time of monthly inspection.

Page 23
  • PRECAUTIONS TO BE HEEDED WHEN MOVING THE MACHINE

machine with the plug as is inserted can damage the power cord and cause fire and electric shock hazards. @ When moving the machine on the floor, retract the Adjusters and ensure that Casters make contact with the floor. During transportation, pay careful attention so that Casters do not tread power cords and earth wires. Damaging the power cords can cause electric shock or short circuit.

A @ When moving the machine, be sure to unplug the power plug. Moving the

WARNING!

When moving the product, do not push the Front Glass. The Glass part could be damaged and glass fractions may cause injury.

CAUTION! When lifting the cabinet, be sure to hold the grip portions or bottom part. Failure to observe this may damage parts and cause injury. Do not push the Billboard. Failure to observe this may damage the installation portions and cause unexpected accidents.

Have casters make contact with the floor.

FIG. 6

Page 24
  • CONTENTS OF GAME

The following explanations apply to the case the product is functioning satisfactorily. Should there be any moves different from the following contents, some sort of faults may have occurred. Immediately look into the cause of the fault and eliminate the cause thereof to ensure satisfactory operation.

The 2 Fluorescent Lamps of the product are always lit when the product is energized. During Advertise, the 2 Speakers and SUPERWOOFER output Advertise sounds, and Advertise images are outputted on to the monitor. Note that setting to NO SOUND OUTPUT during Advertise is possible (refer to the SERVICE MANUAL).

Fluorescent lamps is always on,

Image output on the monitor, Steering Wheel(Handlebar)

START button

Emits sounds.

Coin Inlet

Front Brake

Rear Brake Pedal

}-—_Accelerator Grip

Page 25

HOW TO PLAY

© WILD RIDERS is a motorbike action game, where you play the ace rider of motorbike team who should run away to the goal without being caught by the Police Inspector who is chasing you.

© Throw coins for one play session into the slot. Then, press the START button to display the Select Screen. Select either character from the two riders (man and woman). Selection of the character determines the motorbike type. Each motorbike has its specific characteristics; the key to success in runaway is to take full advantage of its characteristics.

© By determining the character while stepping on the rear brake pedal, the instructions about operating the handlebar will be skipped in the game session.

© Once the Select Screen closes, the Game Screen displays. Once the game session starts, the Police Inspector (on a patrol car) begins to chase you. Run away toward the goal according to the arrows being displayed along the road.

© The distance meter located at the top of the screen indicates the distance from the Police Inspector. If it indicates 0, the game is over.

© You encounter several action points and should clear them by your motorbike action. Two types of motorbike actions are available: Jump and Slide. At a Jump point (orange), jump it by pulling off the handlebar. At a Slide point (green), push the handlebar inward for sliding. If you succeed in each of the actions, you can enlarge the spacing from the Police Inspector. If you fail in it, this spacing reduces reversely.

© Ifyou reach the goal without being caught by the Police Inspector, you get Game Clear and see the Ending view.

e After the game ends, you can view the whole course map to examine to what point you have been able to run away.

© Ifyou acquire a high score at the end of the game, you may go to the Name Entry and be able to enter the initials of your name and so on.

Page 26

INSTRUCTIONS ON OPERATIONS

Basic operations include using the accelerator for accelerating the speed, using the brake for reducing the speed, and using the handlebar for cornering to the left or right. Nothing short of this game enables the following special operations:

FRONT BRAKE LEVER.

\e

EAR BRAKE PEDAL. HANDLE BAR.

ACCELERATOR

"Pull off Handlebar": The motorbike is jumped by pulling off the handlebar at a Jump point, indicated by an orange line. In addition, pulling off the handlebar during usual running allows you to enjoy a wheelie of the motorbike.

"Push Handlebar": When you push the handlebar at a Slide point, indicated by a green line, the motorbike slides. Pushing the handlebar during usual running also slides the motorbike.

FIG. 7b

Page 27

DESCRIPTION OF GAME SCREEN

Police Inspector Window

Your current ranking

Score (Wild Points),

@ Distance Meter:

@ Ranking:

@ Speedometer:

@ Score (Wild Points):

@ Police Inspector Window: Distance Meter

RANK 61 203885 of”

FIG. 7 d US version screen

Indicates the distance from the Police Inspector. When it indicates 0, the game is over. <In the US version, the value is indicated in ft (feet).>

Indicates your current ranking. As you get a higher score, your ranking rises.

Indicates the speed of the motorbike. <In the US version, the value is indicated in mph (miles per hour).>

Each time you succeed a motorbike action or send a small object (e.g., flowerpot) flying, this is counted as an score added.

Displays when the distance from the Police Inspector reduces within the predetermined value, in order to notify you that he is just behind you.

Page 28
  • EXPLANATION OF TEST AND DATA DISPLAY

By operating the switch unit, periodically perform the tests and data check. When installing the machine initially or collecting cash, or when the machine does not function correctly, perform checking in accordance with the explanations given in this section. The following shows tests and modes that should be utilized as applicable.

NAOMI 2 GAME BOARD is used for the product. The system of this game board allows

another game to be played by replacing the ROM Board Case mounted on the NAOMI 2 CASE. As such, the Test Mode of this system consists of the System Test Mode for the system to execute SELF-TEST, COIN ASSIGNMENTS, etc. used in common for the machines employing the NAOMI 2 BOARD, and the Game Test Mode for the specific product to execute Input/Output test for the operation equipment, difficulty setting, etc.

TABLE 8 EXPLANATION OF TEST MODE

ITEMS DESCRIPTION SECTIONS —

INSTALLATION When the machine is installed, perform the following:

OF MACHINE1. Check to ensure each is the standard setting at shipment.8-2E,8-2F,8-3D
  • Check each Input equipment in the INPUT TEST mode. 8-3B
  • Check each Output equipment in the OUTPUT TEST mode. | 8-3C
  • Test on-IC-Board IC's in the SELF-TEST mode. 8-2A, 8-2)

MEMORY This test is automatically executed by selecting RAM TEST, or | 8-2A, 8-25 ROM BOARD TEST in the Menu mode.

PERIODIC Periodically perform the following:

SERVICING1. MEMORY TEST8-2A, 8-2)
  • Ascertain each setting. 83D
  • To test each Input equipment in the INPUT TEST mode. 8-3B
  • To test each Output equipment in the OUTPUT TEST mode. | 8-3C
CONTROL. To check each Input equipment in the INPUT TEST mode.8-3B
SYSTEM2. Adjust or replace each Input equipment.8-3E
  • If the problem still remains unsolved, check each equipment's | 9,10 mechanism movements.
MONITORIn the Monitor Adjustment mode, check to see if Monitor8-2D

(Projector) adjustments are appropriate. 11

IC BOARD1. MEMORY TEST8-2A, 8-2)
  • In the SOUND TEST mode, check the sound related ROMs. 8-2C
DATA CHECKCheck such data as game play time and histogram to adjust the8-2G

difficulty level, etc. 8-3F

Page 29

8-1 SWITCH UNIT AND COIN METER

Touching pl

@ Adjust to the optimum sound volume by considering the environmental requirements of the installation location. , @ [fthe COIN METER and the game board are electrically disconnected, game

IMPORTANT play is not possible.

SWITCH UNIT

Open the coin chute door, and the switch unit shown will appear. The function of each SW is as follows:

FIG. 8. 1a SWITCH UNIT

® SPEAKER VOLUME: Sound volume can be adjusted for the 2 Speakers. SPEAKER VOL WOOFER VOLUME: Sound volume can be adjusted for the WOOFER. WOOFER VOL

® TEST BUTTON: For the handling of the TEST BUTTON, refer to the

TEST following pages.

® SERVICE BUTTON: Gives credits without registering on the coin meter. SERVICE

Page 30

8-2 SYSTEM TEST MODE

The contents of setting changes in SYSTEM ASSIGNMENTS, COIN ASSIGNMENTS, and GAME TEST MODE are stored when the test mode is EXITed. Ifthe power is turned off before EXITing, the contents of setting

IMPORTANT changes are ineffective. Be very careful of this point.

This test mode mainly allows the IC Board to be checked for accurate functioning, monitor color to be adjusted as well as COIN ASSIGNMENTS and GAME ASSIGNMENTS to be adjusted.

TEST ITEM SELECT

@) After turning power on, press the TEST button to have the following test item menu displayed.

SYSTEM MENU

RAM TEST JVS TEST SOUND TEST C.R.T. TEST SYSTEM ASSIGNMENTS COIN ASSIGNMENTS BOOKKEEPING BACKUP DATA CLEAR CLOCK SETTING

ROM BOARD TEST GAME TEST MODE [WILD RIDERS XXXXXXXXX]

-> EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

@) Press the SERVICE button to move the arrow. Bring the arrow to the desired item and press the TEST button.

  • Upon finishing the test, bring the arrow to EXIT and press the TEST button to return to the Game mode.
Page 31

A. RAM TEST

This allows for checking the functioning of the RAM on the NAOMI 2 Main BD. "GOOD" is displayed for satisfactory RAMs, and "BAD" is indicated for irregular RAMs, if any.

RAM TEST

TESTING NOW

1C29 GOOD 1C35 GOOD IC09 GOOD IC10 GOOD IC11 GOOD IC12 GOOD IC16 GOOD IC18 GOOD IC20 GOOD IC22 GOOD IC17 GOOD IC19 GOOD IC21 GOOD IC23 GOOD 1C106 GOOD 1C107 GOOD IC108 GOOD 1C109 GOOD IC111 GOOD 1C113 GOOD IC115 GOOD 1C117 GOOD IC112 GOOD 1C114 GOOD IC116 GOOD 1C118 GOOD

PRESS TEST BUTTON TO EXIT

"TESTING NOW" shows up (flashing) on the screen during the test. Returns to the menu screen when the TEST button is pressed after the test is over.

Page 32

B. JVS TEST

In this test, Specifications of the I/O Board connected to NAOMI 2 can be checked, and INPUT TEST can be performed. First, I/O Board Specifications are displayed.

JVS T INPUT TEST NEXT NODE -> EXIT NODE ma NAME SEGA ENTERPRISES,LTD. VO BD JVS 837-13551 Ver 1.00 CMD VER 1.1 JVS VER 2.0 COM VER 1.0 SWITCH 2PLAYER(S) 13BITS COIN 2SLOT ANALOG — 8CH ROTARY —0CH KEYCODE 0 SCREEN X:0 Y:0 CH:0 CARD OSLOT HOPPER OUT 0CH DRIVER OUT 6SLOT ANALOG OUT 0CH CHARACTER CHARA:0 LINE:0 BACKUP 0

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON (A) (B) (©)

a «Name and version of I/O BOARD.

Select with the SERVICE button and press the TEST button. (A) (B)

(©) Proceeds to the INPUT TEST of I/O BOARD being displayed. In the case where more than 2 I/O Boards are connected, proceeds to INPUT TEST NEXT NODE the next I/O Board. EXIT Returns to the menu mode.

INPUT TEST SCREEN

JVS TEST INPU" NEXT NODE -> EXIT

NODE 1/1

SWITCH SYSTEM PLAYER1 00000000 00000000 00000000 00000000 PLAYER2 00000000 1 $= When INPUT is performed for the switches of Control Panel, etc., the value changes to 1 from 0.

COIN 0000 0000 ANALOG—_, 0000 0000 0000 0000 0000 0000 0000 0000 p> If the Coin SW is inputted, the count starts. ‘When the TEST MODE is finished, the count is cleared and returned to[0000].

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON pe Analogue values are displayed between 0000 and FF00.

Page 33

C. SOUND TEST

Sound Output test can be performed. Beep sounds can be emitted from each of left/right Speakers.

SOUND TEST

RIGHT SPEAKER OFF — Enmitted from the right-hand side Speaker. LEFT SPEAKER OFF — Enmitted from the left-hand side Speaker. -> EXIT — Returns to the menu mode.

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

D. C.R.T. TEST

  • RGB COLOR ADJUSTMENT SCREEN In this page, monitor color can be checked.

C.R.T. TEST 1/2 Each of red, green, and blue is the darkest at the 1 32 leftmost end, and becomes brighter towards the right-hand end in 31 gradations. Monitor

RED! brightness is satisfactory if the white color bar

GREEN is black at the left end and if it is white at the right end. BLUE Press the TEST button to proceed to the next WHITE page.

PRESS TEST BUTTON TO CONTINUE,

  • MONITOR SIZE ADJUSTMENT SCREEN In this page, monitor size can be checked.

maT sCC:-R«.T.. TEST 2/2 Adjust so that the checkered patterns do not go beyond the screen. Press the TEST button to return to the menu mode.

RESS TEST BUTTON TO EXIT +-

Page 34

E. SYSTEM ASSIGNMENTS

The settings of cabinet and board can be changed. Game related assignments such as game difficulty, etc. are performed in K. GAME TEST MODE.

® Press the SERVICE button to move the arrow. Bring the arrow to the desired item.

@ Press the TEST button to change the setting. @vpon finishing the setting, move the arrow to EXIT and press the TEST button.

SYSTEM ASSIGNMENTS

CABINET TYPE1PLAYER(S)(A)

ADVERTISE SOUND ON (B)

MONITOR TYPEHORIZONTAL](C)
SERVICE TYPECOMMON(D)

-> EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

(A) CABINET TYPE (IPLAYER(S), 2PLAYER(S), 3PLAYER(S), 4PLAYER(S)) Sets the number of players between 1 and 4. Fix setting to 1 PLAYER(S).

(B) ADVERTISE SOUND (ON, OFF) Sets whether ADVERTISE sound is to be emitted or not.

(C) MONITOR TYPE (HORIZONTAL, VERTICAL) Sets the on-screen display to the positional direction of monitor (HORIZONTAL/VERTICAL) Fix setting to HORIZONTAL. HORIZONTAL: Normal on-screen display

VERTICAL: On-screen display when the monitor is vertically positioned as against

normal HORIZONTAL position.

(D) SERVICE TYPE (COMMON, INDIVIDUAL) Sets the functioning of when the SERVICE button is pressed, in case that several SERVICE buttons exist. Fix setting to COMMON.

COMMON: By pressing any SERVICE button, Service credit can be obtained for all

Players. INDIVIDUAL: By pressing SERVICE button, Service credit can be obtained for the Player corresponding to the SERVICE button pressed.

Page 35

F. COIN ASSIGNMENTS

In this mode, the setting of incremental credit increase as against coin insertion can be changed.

® Press the SERVICE button to move the arrow. Bring the arrow to the desired item. @) Press the TEST button to change the setting.

@Upon finishing the setting, bring the arrow to EXIT and press the TEST button.

COIN ASSIGNMENTS

MANUAL SETTING SEQUENCE SETTING ->EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON COIN ASSIGNMENTS

COIN CHUTE TYPE COMMON (A) COIN CHUTE TYPE INDIVIDUAL COIN/CREDIT SETTING #1 (B) COIN/CREDIT SETTING #1 COIN CHUTE #1 COIN CHUTE #1 1 COIN 1 CREDIT 1 COIN 1 CREDIT

COIN CHUTE #2 1 COIN 1 CREDIT ©) (G) MANUAL SETTING SEQUENCE SETTING ->EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

Setting to COMMON

(A) COIN CHUTE TYPE (COMMON, INDIVIDUAL) Fix setting to COMMON.

COMMON Setting to INDIVIDUAL

This setting is for the cabinet which has a coin chute(s) for common use by plural players. Up to 2 Coin Chutes (#1 and #2) can be used and also, (B) COIN/CREDIT SETTING ratio can be set separately for #1 and #2.

INDIVIDUAL This setting is for the cabinet in which each player uses an independent coin chute. Coins inserted by each player are handled as the player's credits. Depending on the CABINET TYPE setting in the SYSTEM ASSIGNMENTS and the functioning of the connected I/O Board, the number of Coin SW INPUT ports varies between | and 4. (B) COIN/CREDIT SETTING ratio is common for eath Coin Chute.

(B) COIN/CREDIT SETTING ( # 1 ~# 27) Sets the credit increase increment per coin insertion. There are 27 settings from #1 to #27, expressed in © © credit(s) as against © © coins inserted. #27 refers to FREE PLAY. For details, refer to Table 1 (COMMON) and Table 2 (INDIVIDUAL).

Page 36

(C) MANUAL SETTING The Credit's incremental increase settings as against a coin insertion are shown in further details than in (B) above (refer to Table 3). Also, note that when this MANUAL SETTING is performed, (B) COIN CREDIT setting becomes ineffective.

MANUAL SETTING

COIN ASSIGNMENTS MANUAL SETTING

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON COIN ASSIGNMENTS MANUAL SETTING

ocREDIT COINTOCREDIT 1 COINTOCREDIT 1 () : .

BONUS ADDER NO BONUS ADDER (E) CONCHUTE MULTIBLIER, ADDER

COIN CHUTE #1 MULTIPLIER | Cort COUNT Ae Com 1 COIN COUNT AS 1 COIN Con isha 4 eae COIN 123456789 N CREDIT 123456789 CREDIT 123456789

COIN CHUTE #2 MULTIPLIER 1 COIN COUNT AS 1 COIN COIN 123456789 CREDIT 123456789

© SEQUENCE SETTING

->EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

Setting to COMMON

(D) COIN TO CREDIT Setting to INDIVIDUAL

Determines COIN/CREDIT setting.

(E) BONUS ADDER This sets how many coins should be inserted to obtain one SERVICE COIN.

(F) COIN CHUTE ( # 1 / #2.) MULTIPLIER This sets how many tokens one coin represents.

Page 37

Table 1: COIN/CREDIT SETTING (COIN CHUTE COMMON TYPE)

NAME OF SETTING COIN CHUTE 1 COIN CHUTE 2

SETTING #1 1_ COIN1 CREDIT1 COIN1 CREDIT
SETTING #2 1 _ COIN2_ CREDITS1 COIN1 CREDIT
SETTING #3 1 COIN3__ CREDITS1 COIN1 CREDIT
SETTING #4 1 COIN4 CREDITS1 COIN1 CREDIT
SETTING #5 1_ COIN5 CREDITS1_ COIN1_CREDIT
SETTING #6 1_ COIN2_ CREDITS1 COIN2 CREDITS
SETTING #7 1_ COIN5 CREDITS1 COIN2 CREDITS
SETTING #8 1 COIN3__ CREDITS1 COIN3 CREDITS
SETTING #9 1_ COIN4 CREDITS1 COIN4 CREDITS
SETTING #10 1_ COIN5 CREDITS1 COIN5_CREDITS
SETTING #11 1 COIN6 CREDITS1 COIN6 CREDITS

SETTING #12 2 COINS 1 CREDIT 2 COINS 1 CREDIT

SETTING #13 1_ COIN1 CREDIT2 COINS 1 CREDIT
SETTING #14 1_ COIN2_ CREDITS2 COINS 1_ CREDIT
SETTING #15 1 COIN1 CREDIT1 COIN1 CREDIT

2 COINS 3 CREDITS 2 COINS 3 CREDITS

SETTING #16 1 COIN3. CREDITS1 COIN1 CREDIT

2 COINS 3__CREDITS

SETTING #17 3__COINS 1 CREDIT 3__COINS 1_ CREDIT

SETTING #18 4 COINS 1 CREDIT 4 COINS 1_ CREDIT

SETTING #19 1 COIN1 CREDIT1 COIN1 CREDIT

2 COINS 2 CREDITS 2 COINS 2 CREDITS

3 COINS 3. CREDITS 3 COINS 3. CREDITS

4 COINS 5 CREDITS 4 COINS 5_ CREDITS

SETTING #20 1 COIN5 CREDITS1 COIN1 CREDIT

2 COINS 2 CREDITS

3 COINS 3 CREDITS

4 COINS 5 CREDITS

SETTING #21 5__COINS 1 CREDIT 5 COINS 1 CREDIT

SETTING #22 1 COIN2 CREDITS3 COINS 1 CREDIT

5__COINS 2 CREDITS

SETTING #23 2 COINS 1 CREDIT 2 COINS 1 CREDIT

4 COINS 2 CREDITS 4 COINS 2 CREDITS

5__COINS 3__ CREDITS 5__COINS 3__CREDITS

SETTING #24 1 COIN3. CREDITS2 COINS 1 CREDIT

4 COINS 2 CREDITS

5__COINS 3__CREDITS

SETTING #25 1 COIN1 CREDIT1 COIN1 CREDIT

2 COINS 2 CREDITS 2 COINS 2 CREDITS

3 COINS 3. CREDITS 3 COINS 3. CREDITS

4 COINS 4 CREDITS 4 COINS 4 CREDITS

5_COINS 6 CREDITS 5_COINS 6 CREDITS

SETTING #26 1 COIN6 CREDITS1 COIN1 CREDIT

2 COINS 2 CREDITS

  • COINS 3. CREDITS

4 COINS 4 CREDITS

5__COINS 6 CREDITS

SETTING #27 FREE PLAY FREE PLAY

Page 38

Table 2: COIN/CREDIT SETTING (COIN CHUTE INDIVIDUAL TYPE)

NAME OF SETTING]EACH SEAT'S COIN CHUTE,NAME OF SETTING]EACH SEAT'S COIN CHUTE.
SETTING #11COIN _ 1 CREDITSETTING #215 COINS_1 CREDIT
SETTING #21COIN2 CREDITSSETTING #232 COINS1 CREDIT
SETTING #31COIN3 CREDITS4COINS2 CREDITS
SETTING #41COIN4 CREDITS5 COINS3 CREDITS
SETTING #51COIN5 CREDITSSETTING #251COIN1 CREDIT
SETTING #111COIN6 CREDITS2COINS2 CREDITS
SETTING #122 COINS1 CREDIT3COINS3 CREDITS
SETTING #151COIN1 CREDIT4COINS4 CREDITS
2 COINS3 CREDITS5 COINS6 CREDITS
SETTING #173 COINS1 CREDITSETTING #27FREE PLAY
SETTING #184COINS_1 CREDIT
SETTING #191COIN1 CREDIT

2COINS 2 CREDITS

3COINS 3 CREDITS 4 COINS _5 CREDITS

Table 3: MANUAL SETTING

COIN TO CREDIT1COIN1CREDIT
2COINS1CREDIT
3__COINS1CREDIT
4COINS1_CREDIT
5COINS1CREDIT
6COINS1CREDIT
7__COINS1CREDIT
8COINS1CREDIT
9COINS1CREDIT

BONUS ADDER NO BONUS ADDER 2 COINS GIVE _1 EXTRA COIN 3 COINS GIVE _1 EXTRA COIN 4 COINS GIVE _1 EXTRA COIN 5 COINS GIVE _1 EXTRA COIN 6 COINS GIVE _1 EXTRA COIN 7 COINS GIVE _1 EXTRA COIN 8 COINS GIVE _1 EXTRA COIN 9 COINS GIVE 1 EXTRA COIN

COIN CHUTE (#1/#2)1_COINCOUNTS AS_1COIN
MULTIPLIER1COINCOUNTS AS2 _ COINS
1COINCOUNTS AS__3__COINS
1COINCOUNTS AS4COINS
1COINCOUNTS AS5COINS

1 COINCOUNTS AS__6__COINS

1COINCOUNTS AS__7COINS
1COINCOUNTS AS8 _ COINS
1COINCOUNTS AS9COINS
Page 39

(G) SEQUENCE SETTING Number of credits required for starting game, etc. can be set. Function varies depending on the specific games. To find out what kind of functions are allotted to each sequence, or what is the initial value for each sequence, refer to the Instruction Manual of the game connected. Each sequence can be set between | ~ 5 credit(s).

COIN ASSIGNMENTS SEQUENCE SETTING

SEQUENCE 1 1 CREDIT SEQUENCE 2 1 CRED SEQUENCE 3.1 CRED’ SEQUENCE 4 1 CREDI SEQUENCE 51 CREDIT(S) SEQUENCE 6 1 CREDIT(S) SEQUENCE 7 1 CREDIT(S) SEQUENCE 8 1 CREDIT(S) -> EXIT [WILD RIDERS XXXXXXXXXX] DESCRIPTION OF SEQUENCE 1 CREDIT TO START 2 NO USE 3 NO USE 4 NO USE 5 NO USE 6 NO USE 7 NO USE 8 NO USE

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

In cases of video games such as WILD RIDERS. : SEQUENCE |: Number of credits required for game start (initial value=1) SEQUENCE 2~8: NOT USED.

Page 40

G. BOOKKEEPING

+ BOOKKEEPING 1/2 This allows such data as operating time/No. of coins inserted/ No. of credits to be checked.

BOOKKEEPING 1/2

TOTAL TIME OD 00H 00M 00S

CREDIT 0

COIN 1 COIN 2 COIN 3 COIN 4 coco

TOTAL COIN COIN CREDIT SERVICE CREDIT TOTAL CREDIT ecoo

PRESS TEST BUTTON TO CONTINUE

Press the TEST button to proceed to BOOKKEEPING 2/2.

  • BOOKKEEPING 2/2 Each sequence displays the frequency of functioning.

BOOKKEEPING 2/2

P1SEQ1 P1 SEQ 2 P1 SEQ 3 P1 SEQ 4 P1SEQ5 P1 SEQ 6 P1 SEQ7 P1 SEQ 8 ocoooocc]o

PRESS TEST BUTTON TO EXIT

In cases of video games such as WILD RIDERS. : PISEQ1: Play frequency of Player | P1SEQ2~8: NOT USED.

Page 41

H. BACKUP DATA CLEAR

Clears the contents of BOOKKEEPING.

BACKUP DATA CLEAR

YES(CLEAR) -> NO(CANCEL)

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

When clearing, bring the arrow to YES by using the SERVICE button and press the TEST button. Bring the arrow to NO and press the TEST button to have the menu mode return without clearing the data. COMPLETED is displayed when clearing is completed. Press the TEST button to return to the menu mode.

I. CLOCK SETTING

Set YEAR, MONTH, DAY, HOUR, and MINUTE for NAOMI 2 Main BD.

CLOCK SETTING

1998 12/02 14:30 33 WED

YEAR MONTH DAY HOUR MINUTE -> EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

Select the desired item with the SERVICE button and press the TEST button to increase the value. Upon finishing the SETTING, bring the arrow to EXIT and press the TEST button to return to the menu mode.

Page 42

J. ROM BOARD TEST

In this test, on-ROM-BD ROM check is executed. If GOOD is displayed below RESULT, it is satisfactory. BYTE and WORD refers to the check sum of each unit.

GAME ROM TEST [WILD RIDERS XXXXXXX]

NO. TYPE RESULT BYTE WORD. 1C22 16M _ ---- 0123 4567 IC1 64M GOOD 0123 4567 IC2 64M GOOD 0123 4567 IC3 64M GOOD 0123 4567 IC4 64M GOOD 0123 4567 IC5 64M GOOD 0123 4567 IC6 64M GOOD 0123 4567 IC7 64M GOOD 0123 4567 IC8 64M GOOD 0123 4567 IC9 64M GOOD 0123 4567 IC1064M GOOD 0123 4567 1c20 64M GOOD 0123 4567

PRESS TEST BUTTON TO EXIT

Program ROMs (IC22) do not display GOOD or BAD. Press the TEST button to return to the menu mode.

K. GAME TEST MODE

Enters the TEST mode of the game connected. The TEST mode includes INPUT test, GAME ASSIGNMENTS such as game difficulty and others, BOOKKEEPING, etc. Depending on specific games, necessary items are added and unnecessary items removed. As such, the contents thereof may be changed.

Page 43

8-3 GAME TEST MODE

A. MENU MODE

SYSTEM MENU

GAME TEST MENU

RAM TEST JVS TEST INPUT TEST SOUND TEST OUTPUT TEST C.R.T. TEST GAME ASSIGNMENTS. VOLUME ADJUSTMENTS BOOKKEEPING BAUKUP DATA CLEAR SYSTEM ASSIGNMENTS, COIN ASSIGNMENTS BOOKKEEPING BACKUP DATA CLEAR CLOCK SETTING

ROM BOARD TEST -> GAME TEST MODE [WILD RIDERS XXXXXXX] ->EXIT

Parr SELECT WITH SERVICE BUTTON

SELECT WITH SERVICE BUTTON AND PRESS TEST SULTON,

AND PRESS TEST BUTTON

SYSTEM TEST MODE MENU GAME TEST MODE MENU

FIG. 8.3 a MENU MODE

  • Press the TEST button to display the SYSTEM TEST MODE MENU.

+ By pressing the SERVICE button, move the arrow (->) to select the GAME TEST MODE.

  • Press the TEST button to enter GAME TEST MODE. The screen displays the GAME TEST MODE MENU.

+ By pressing the SERVICE button, move the arrow (->) to select the desired item . Press the TEST button to execute the selected item.

  • Select EXIT and press the TEST button to exit from the GAME TEST MODE and return to the SYSTEM TEST MODE MENU. Further, select EXIT and press the TEST button to finish SYSTEM TEST MODE and return to the normal mode.
Page 44

B. INPUT TEST

Selecting INPUT TEST displays the following and allows the status of each switch to be checked and the Volume value of each operative unit to be observed. In this mode, periodically check the status of each switch and Volume.

INPUT TEST

HANDLEBAR 80

ACCELERATOR 00

FRONT BRAKE 00 REAR BRAKE 00 PUSH OFF PULL OFF START OFF SERVICE OFF TEST OFF

PRESS TEST AND SERVICE BUTTON TO EXIT

FIG. 8.3 ba INPUT TEST

HANDLE BAR I

HANELEBAR iS REAR_ BRAKE

FIG. 8. 3 bb FIG. 8. 3 be

  • Press each switch. If the indicator to the right of the switch (currently Off) turns On, the switch and its wiring are normal.
  • While operating the handlebar and pedal, check the variation in indication of the volume control value (HANDLEBAR, ACCELERATOR, FRONT BRAKE, REAR BRAKE). If the normal variation does not result that follows the operations, see Sections 9 and 10.

+ Pressing the TEST and SERVICE buttons together returns you to the Menu Screen.

Page 45

C. OUTPUT TEST

Selecting OUTPUT TEST displays the following on the monitor and allows the status of Lamp to be checked. In this mode, periodically check the lamp status. Bring the arrow (->) to "START LAMP" and press the TEST button to alternate the righthand ON and OFF display of START LAMP.

Check to ensure that the lamp lights up when ON is displayed and goes off when OFF is displayed. Bring the arrow (->) to "EXIT" and press the TEST button to return to the Test Menu.

OUTPUT TEST

START BUTTON LAMP OFF

->EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

FIG. 8.3 c OUTPUT TEST

Page 46

D. GAME ASSIGNMENTS

When GAME ASSIGNMENTS are selected, the following appears on the monitor and Game Difficulty, etc. can be set. The setting change is not renewed until the TEST mode is exited. After setting change, be sure to exit from the TEST mode.

GAME ASSIGNMENTS.

DIFFICULTY NORMAL

ADVERTISE SOUND VOLUME 1

->EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

FIG. 8. 3 d GAME ASSIGNMENTS,

DIFFICULTY : Setting the difficulty of the game gs y gi You can select one of 5 levels of "VERY EASY," "EASY," "NORMAL," "HARD," and "VERY HARD."

@ ADVERTISE SOUND VOLUME : For the advertisement sound volume, you can select one of 8 levels of "0" to "8". The larger the value, the larger the sound volume ("0" is the minimum).

  • Move the arrow with the SERVICE button to choose the setting change item. Press the TEST button to change the difficulty.

+ Bring the arrow to EXIT and press the TEST button to return to the menu mode.

Page 47

E. VOLUME ADJUSTMENTS

If you select "VOLUME ADJUSTMENTS," the monitor screen lists the information below, which lets you set the volume controls of each operations unit. If the operability is poor or you have adjusted or replaced one or more volume controls, use this mode to set them. At this time, you must set the following four types of volume controls: HANDLEBAR, ACCELERATOR, FRONT BRAKE, and REAR BRAKE. The MAX. value, MIN. value for each and the HANDLEBAR's NEUTRAL value are to be set as applicable.

VOLUME ADJUSTMENTS

MINMAXNEUTRAL
HANDLEBAR[00H][FFH][80H]
(00H)(FFH)(80H)
ACCELERATOR [00H][FFH][00H]

(00H) (FFH)

FRONT BRAKE[00H][FFH][00H]

(00H) (FFH)

REARBRAKE[00H][FFH][00H]

(00H) (FFH)

EXIT WITH SAVE

->EXIT WITHOUT SAVE

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

FIG. 8.3 e VOLUME ASSIGNMENTS

Move the handlebar, the accelerator, and the front and rear brake pedals fully in the movable range to set the proper volume control values. Any value in brackets [ ] is the initial, or unadjusted value; any value in parentheses (_) is the currently backed up one.

Page 48

HANDLEBAR : Fully move the handlebar to the clockwise or counterclockwise end. 'y Then, return it to the middle to place it in the state where no force is applied to it.

ACCELERATOR : Fully turn the accelerator grip. Then, release it to return it to the state e ly grip where no force is applied to it.

@ FRONT BRAKE : Fully grasp the front brake lever. Then, release it to return it to the state where no force is applied to it.

@ REAR BRAKE : Fully step on the rear brake pedal. Then, release it to return it to the state where no force is applied to it.

The settings you have made are not updated until "EXIT WITH SAVE" is completed. To update them, be sure to perform "EXIT WITH SAVE." If you select "EXIT WITHOUT SAVE" before pressing the Test button, the system returns you to the Menu Screen without updating the settings.

APPROPRIATE VOLUME LEVELS

The range of appropriate volume levels are shown below. Ifa value outside the range is indicated, the volume may get damaged, in which case the volume gear should be disengaged once, and the angle of engagement should be modified (see Sections 10 and 11).

  • HANDLEBAR 26H ~ 4AH 80H +/-5 C5H ~ EBH Turn handlebar to the left Initial state Turn handlebar to the right
+ ACCELERATOR10H ~ 30HDOH ~ FOH

When your hand is removed from the grip Turn the grip all the way

+ FRONT BRAKE20H ~ 30H9EH ~ ADH

When your hand is removed from the lever Pull the lever all the way

* REAR BRAKE2DH ~ 33HBOH ~ BFH

When your foot is removed from the pedal Step on the pedal all the way

4l

Page 49

F. BOOKKEEPING

If you select BOOKKEEPING, data about the current operation will be listed on two screens. When you press the TEST button, you go to the next screen. When you press it while the second screen remains in display, you return to the Menu Screen. The first screen (1 of 2) lists data related to the progress of the play.

BOOKKEEPING PAGE 1/2

NUMBER OF GAMES 0

PLAY TIME OD 0H 0M OS

AVERAGE PLAY TIME 0M 0S

LONGEST PLAY TIME 0M 0S

SHORTEST PLAY TIME 0M OS

PRESS TEST BUTTON TO CONTINUE

FIG. 8. 3 fa BOOKKEEPING (1/2)

@ NUMBER OF GAMES _ :: Total number of sessions played.

@ PLAY TIME : Time taken for the game.

BOOKKEEPING PAGE 2/2 The second screen (2 of 2) TIME HISTOGRAM lists the number of sessions played that corresponds to each PLAY TIME. It provides a guide for setting up the difficulty and so on. 0M 00S ~0M 29S 0 0M 30S~0M59S_ O 1M00S~1M29S_ 0 1M 30S~1M59S_ 0 2M 00S ~2M29S_ 0 2M 30S ~2M39S_ O 3M 00S~3M 29S O 3M 30S~3M59S_ O 4M 00S~4M 29S 0 4M 30S~4M59S_ 0 5M 00S ~5M 29S 0. 5M 30S~5M59S_ 0 6M 00S ~6M 29S 0 6M 30S~6M59S_ 0 7M 00S~7M 29S O 7M 30S~7M 59S O 8M 00S ~8M 29S 0 8M 30S ~8M59S_ 0. 9M 00S ~9M 29S 0 9M 30S~9M59S_ 0 OVER 10M00S_ 0

PRESS TEST BUTTON TO EXIT

FIG. 8.3 fb BOOKKEEPING (2/2)

Page 50

G. BACKUP DATA CLEAR

This allows the contents of BOOKKEEPING and the Ranking data to be cleared. Despite the "clear" execution, the settings of GAME ASSIGNMENTS do not change. The contents of BOOKKEEPING in the SYSTEM TEST mode are not cleared either.

When clearing, use the SERVICE button to bring the arrow (->) to "YES (CLEAR)" and press the TEST button. When the data has been cleared, "COMPLETED" will be displayed. Press the TEST button to return to the Menu mode. Bring the arrow to "NO (CANCEL)" and press the TEST button to return to the Menu mode.

BACKUP DATA CLEAR

YES(CLEAR) ->NO (CANCEL)

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

FIG. 8.3 g BACKUP DATA CLEAR

Page 51

9. CONTROL PANEL (HANDLE MECHA)

this can cause electric shock or short circuit. Use care so as not to damage wirings. Damaged wiring can cause electric shock or short circuit. Do not touch undesignated places. Touching places not designated can cause electric shock or short circuit. This work should be performed by the Location's Maintenance Man or Serviceman. Performing work by non-technical personnel can cause electric shock hazard.

i Before starting to work, ensure that the Power SW is OFF. Failure to observe

WARNING!

When closing the Control Panel, be very careful so as not to have hand and fingers pinched in.

CAUTION! Be careful when handling the plastic made parts. Failure to observe this may cause injury due to damage or fragments resulting from damage.

For the handlebar volume control, use the volume control with Part Number 220- 5373. For the front brake or accelerator volume control, use the volume control with Part Number 220-5484. Do not confuse them.

IMPORTANT

The control panel of this product contains volume controls that are used to detect operations of the handlebar, accelerator, and front brake. Verify operations of the input devices at least once a month. If a failure is found, immediately take proper action. This document describes how to adjust and replace the volume controls. The mechanisms of each input device is required to be greased every 3 months.

Page 52

9-1 ADJUSTING / REPLACING THE HANDLEBAR VOLUME

ADJUSTING THE VOLUME

The following procedure requires a wrench for tamperproof screw (for M4, accessories), Phillips screwdriver (for M4), and the master key.

® Remove the 4 tamperproof screws that

secure the Front lid to the base of the handlebar. Remove the single tmaperlproof bolt connecting the handlebar assembly to the shaft. Then remove the handlebar assembly momentarily.

TAMPERPROOF SCREW (2)

TAMPERPROOF SCREW (2)

PHOTO 9. 1a

@ Remove the Front Lid.

Page 53

® Loosen the 2 screws securing the VR

Bracket, and then this bracket can be moved (PHOTO 10.1c).

M4 X 12, w/flat & spring washers PHOTO 9. 1c

  • Move the VR Bracket back and forth to adjust the mesh of the gear. Moving the VR Bracket toward you disengages the mesh of the gear. By turning the volume control gear manually, vary the angle of the mesh (PHOTO 9.14).

PHOTO 9. 1d

® In the Test mode, check that the handlebar control volume varies properly.

Page 54

Before any action is taken, turn off the main switch on the AC Unit in the back of the game.

@ By reaching up through the coin door, untie

the cord clamp securing the wire of the handlebar volume control, and pull off the connector (PHOTO 10.1g).

Disconnect the connector.

PHOTO 9. 1 g

SCREW (2) M4 X 12, w/flat & spring washers

Remove the 2 screws securing the VR bracket. Then, remove the volume control together with the bracket (PHOTO 10.1h).

220-5373

Remove the gear from the volume control. Remove the VR bracket. Cut the wire used for soldering. Then replace the volume control.

® Check that, when you fully turn the handlebar clockwise or counterclockwise, check that the swing does not attempt to go outside the range of revolution of the volume control spindle.

© Turn on the power. In the test mode, set the volume control value (see Section 8-3).

Page 55

9-2 ADJUSTING / REPLACING THE FRONT BRAKE VOLUME

In the test mode, if the Front Brake Volume's value movements are irregular, adjust or replace the Volume by using the following procedure. This procedure requires a Phillips screwdriver (for M4), a hexagonal wrench with an oppositeside distance of 1.5 mm, nippers, the master key, a solder iron, and solder. Take out the 4 screws and remove the VR Cover. The Front Brake Volume is inside the VR Cover.

TRUSS SCREW (4),black VR COVER

PHOTO 9. 2a

VOLUME ADJUSTMENT

® Loosen the 2 screws which secure the VR Bracket to move the VR Bracket. @)Move the VR Bracket to disengage gear mesh.

® Loosen the 2 screws which secure the VR Bracket to move the VR Bracket @)Move the VR Bracket to disengage gear mesh @y adjusting gear mesh, fasten the 2 screws @Move the Brake Lever fully to the movable

which secure the VR Bracket.

range and check if the Volume Shaft's revolvable range is exceeded.

®Afeer the adjustment, be sure to perform the

Volume setting in the test mode.

VOLUME

VOLUME REPLACEMENT

Replace the Volume if it is malfunctioning. Install the Volume in the manner so that 25H +/

  • 5 is indicated when force is not exerted.

Remove the 2 screws which secure the VR

Bracket.

2) Remove the Volume Gear from the Volume

Shaft and remove the Volume from the VR Bracket to replace the Volume.

@Afier the replacement, be sure to perform the CREW (2)

Volume setting in the test mode. M4 X 8, w/flat & spring washers PHOTO 9.2b

Page 56

9-3 ADJUSTING / REPLACING THE ACCELERATOR VOLUME

In the test mode, if the Accelerator Volume's value movements are irregular, adjust or replace the Volume by using the following procedure. This procedure requires a short Phillips screwdriver(for M4), a hexagonal wrench with an opposite-side distance of 1.5 mm, nippers, the master key, a solder iron, and solder.

Remove the 4 screws, and the VR Cover. The Accelerator Volume appears inside the Cover.

_TRUSS SCREW (4),black M4X8

VR COVER A

PHOTO 9.3 a

VOLUME ADJUSTMENT

® Loosen the screw which secures the VR Bracket to move the VR Bracket. @Move the VR Bracket to disengage gear mesh. @y adjusting gear mesh, fasten the screw which secures the VR Bracket. @turn the Accelerator Grip fully to the movable range and check if the Volume Shaft's revolvable range is exceeded. ®atier the adjustment, be sure to perform the Volume setting in the test mode.

SCREW (1) M4 X 8, wiflat & spring washers VOLUME REPLACEMENT

Replace the Volume if it is malfunctioning. Install the Volume in the manner so that 20H +/ - 5 is indicated when force is not exerted.

® Remove the screw which secures the VR @Remove the Volume Gear from the

Bracket.

Volume Shaft and remove the Volume from the VR Bracket to replace the Volume.

@atier the replacement, be sure to perform

the Volume setting in the test mode. A}OLUME PHOTO 9. 3b 220-5484

Page 57

9-4 GREASING

Grease is inflammable and must never be close to fire. Grease does harm to your body if you aspirate it. Do not perform any work related to grease in a location where ventilation is insufficient.

CAUTION! If grease adheres to your skin or enters an eye, immediately rise with clean water. If you feel out of sorts while you are performing the work, immediately stop it and keep quiet in a well-ventilated area. If you do not recover, consult with a doctor. Do not eat grease. Should you eat it, you may have loose bowels or feel like vomiting. Should somebody swallow it, immediately have his or her illness diagnosed by a doctor, without compelling him or her to vomit the grease.

IMPORTANT

Be sure to use the designated type of grease. If a non-designated type grease is

used, components may break. The period for greasing specified herein is a standard. Apply greasing to the specified portions as occasion arises. Do not apply greasing to places other than those specified. Greasing to undesignated places can cause malfunctioning and the qualitative deterioration of parts. Do not grease any portions other than the specified ones. Use an extension tube annexed to spray grease.

Page 58

Once every 3 months, apply greasing to the following places. For greasing, use Grease Mate (P. No. 090-0066).

Handlebar Volume Control Mesh (Spring) Front Brake Volume Control Gear Mesh PHOTO 9.4a PHOTO 9. 4b

Brake Sliding Surface Accelerator Volume Control Mesh PHOTO 9.4¢ PHOTO 9. 4d

Page 59

GREASING THE HANDLEBAR MECHANISM

Greasing the handlebar mechanism requires a wrench for tamperproof screw (for M4, accessories) and a hexagonal wrench with an opposite-side distance of 3 mm.

® Remove the control panel cover (see Section 9-1). @ Remove the 4 screws with hexagonal hole (PHOTO 9.4e). ® Remove the ASSY centering mechanism (PHOTO 9.4f).

HEXAGON SOCKET SCREW (4 M4 X 10, flat & spring washers used. ASSY CENTERING MECHANISM.

mv ‘ PHOTO 9.4e PHOTO 9.4 f

AIN SHAFT

CAM Bearing par

SPRING

2 2 SENSOR Do.not get the light receiving/ emitting face contaminated.

3 o

GUIDE

R GEAR

FIG. 9. 4

Page 60

® Grease the sliding surface of the

cam (PHOTO 9.4g).

® Grease a total of 4 springs (at the

left and right) (PHOTO 9.4h).

PHOTO 9. 4h

  • Grease the slide surfaces of the handlebar shaft and the left and right shafts (PHOTO 9.4i, j).

PHOTO 9. 4i PHOTO 9. 4j

Page 61

9-5 REPLACING THE SPRING

The mechanism that returns the handlebar to the direction of going straight ahead uses one HOLD spring. The mechanism that returns the handlebar to the regular position uses 4 SUS springs. If one of the springs has failure such as deformation, the operability will be unsatisfactory. If so, use the following procedure to replace the spring with a spare. The replacement requires a wrench for tamper proof screw (for M4, accessories), a hexagonal wrench with an opposite-side distance of 3 mm, and a pair of pliers.

@)Remove the control panel cover (see Section 9-1). @ Remove the 4 screws with hexagon hole, and then remove the ASSY centering mechanism (see Section 9-4).

@while holding the HOLD spring

with the pliers, release the hooks located at both ends of the spring (PHOTO 9.5a). =

SPRING HOLD WRD-2105

PHOTO 9.5a

@The handlebar mechanism has a round hole on

each of the left and right sides. Insert the pliers into the round hole, hold the SUS spring, and

release the hook of both ends of the spring

(PHOTO 9.5b). 1 = Bib

HOOK PART

Wound 2 to 3 times.

SPRING SUS WRD-2010 _ Do not let the hook part at both ends (made of SUS material) shift beyond the position where the number of winding is 2 to 3 wounds from the end.

PHOTO 9. 5b

Page 62
  • REAR BRAKE
WARNING! Before starting to work, ensure that the Power SW is OFF. Failure to observe this can cause electric shock or short circuit. Use care so as not to damage wirings. Damaged wiring can cause electric shock or short circuit. Do not touch undesignated places. Touching places not designated can cause electric shock or short circuit. This work should be performed by the Location's Maintenance Man or Serviceman. Performing work by non-technical personnel can cause electric shock hazard.

If the operability of the brake pedal is poor or execution of the VOLUME ADJUSTMENTS in Test mode has no effect, adjust the volume control gear mesh or replace the volume control. In this product, when the Pedals are fully stepped on, if the Volume shaft is rotating within the movable range, the Volume is not feared to be damaged. Secure the Volume in the manner the Volume Shaft is oriented as shown and the gears are appropriately engaged when the Pedals are not stepped on.

10 - 1 REMOVING THE BRAKE UNIT

® Turn power OFF by using the Main SW of AC Unit, or SUB PWR SW inside the SERVICE DOOR.

@ Take out the 4 Truss screws and remove the

Floor Lid. (PHOTO 10.1a)

CARRIAGE BOLTS,

PHOTO 10. 1a

Page 63

@ Disconnect the connector.

@ Disconnect the connector ® Remove the 6 hexagon nuts, and disengage the

brake unit from the ASSY Floor (PHOTO 10.1b).

PHOTO 10. 1b

10-2: ADJUSTING / REPLACING THE REAR BRAKE VOLUME

Adjusting or replacing the volume controls requires a Phillips screwdriver (for M4 screw), a hexagonal wrench with an opposite-side distance of 1.5 mm, nippers, the master key, a solder iron, and solder.

ADJUSTMENT

Loosen the 2 screws, move the VR Bracket, and adjust the angle and appropriateness of gear mesh.

—YOLUME SCREW (2)

220-5373 axe ik | party MA X 8, wiflat & spring washers

© 1 £1 | g or | Lo} eO® 2 © 5 oe @;

VR BRACKET, \ FIG. 10.2 "D"CUT FACE

REPLACEMENT

® Take out the 2 screws and remove the Volume together with the VR Bracket. @ After replacing the Volume, engage the gears at the angle shown, and fix the VR Bracket. ® Install the Brake Unit and connect the Connector. @tTum power ON and set the Volume value in the test mode.

Page 64

10-3 GREASING

Grease is inflammable and must never be close to fire. Grease does harm to your body if you aspirate it. Do not perform any work related to grease in a location where ventilation is insufficient.

CAUTION! f grease adheres to your skin or enters an eye, immediately rise with clean water. f you feel out of sorts while you are performing the work, immediately stop it and keep quiet in a well-ventilated area. If you do not recover, consult with a doctor. Do not eat grease. Should you eat it, you may have loose bowels or feel like vomiting. Should somebody swallow it, immediately have his or her illness diagnosed vy a doctor, without compelling him or her to vomit the grease.

IMPORTANT

Be sure to use the designated type of grease. If a non-designated type grease is

used, components may break. The period for greasing specified herein is a standard. Apply greasing to the specified portions as occasion arises. Do not apply greasing to places other than those specified. Greasing to undesignated places can cause malfunctioning and the qualitative deterioration of parts. Do not grease any portions other than the specified ones. Use an extension tube annexed to spray grease.

Page 65

Apply greasing to gear mesh portions once every 3 months. Use GREASE MATE (SEGA PART NO. 090-0066).

SLIDING FACE OF PEDAL SHAFT

VOLUME GEAR MESH PORTION,

FIG. 10.3

PHOTO 10.3

Page 66
  • MONITOR

11 - 1 CAUTIONS AND WARNINGS CONCERNING THE SAFETY FOR HANDLING THE MONITORS Before handling the monitors, be sure to read the following explanations and comply with the

caution/warning instructions given below. Note that the caution/warning symbol marks and letters are used in the instructions. Indicates that handling the monitors Indicates that handling the monitors by erroneously by disregarding this warning may disregarding this caution may cause a cause a potentially hazardous situation, potentially hazardous situation, which could result in personal injury and or material
WARNING! which could result in death or serious injury. CAUTION! damage.

Indicates that access to a specific part of the Indicates the instruction to disconnect a equipment is forbidden. power connector or to unplug.

@ When performing such work as installing and removing the monitor, inserting and disconnecting the external connectors to and from monitor interior and the monitor, be sure to disconnect the power connector (plug) before starting the work. Proceeding the work without following this instruction can cause electric shock or malfunctioning. + @ Using the monitor by converting it without obtaining a prior permission is not allowed. SEGA shall not be liable for any malfunctioning and accident caused by said conversion.

@ Primary side and Secondary side The monitor's circuit which is divided into the Primary side and Secondary side, is electrically isolated. Do not touch the primary side, or do not touch both the primary side and the secondary side simultaneously. Failing to observe the instruction can cause electric shock and this is very dangerous. When making monitor adjustments, use a nonconductive driver and make adjustment without touching any part other than the Adjustment V. R. and knob. Also, be sure not to cause a short-circuit to the Primary side and Secondary side. If short-circuited, it can cause electric shock or malfunctioning, which is very dangerous. @ High-tension Voltage Some of the parts inside monitor are subject to high-tension voltage in excess of 20,000 volts and very dangerous. Therefore, do not touch the monitor interior. Should soldering & paper wastes, etc. be mixed in the monitor interior, turn the power off so as not to cause malfunctioning or fire hazar " ANODE CAP PRIMARY SIDE DEMAGNETIZER REAR PART COIL ANODE LEAD | MAIN BD Approx. 29 kV SECONDARY SIDE (Chassis, CRT)

PRIMARY SIDE

DEMAGNETIZER ‘ FOCUS LEAD COIL (black) | Approx. 10 kV NECK PCB

. Approx, IN ik SECONDARY SIDE sone FBT Approx. KS

(Chassis, sheet metal work, CRT, ete.) & Disconnect or unplug 29 kV

@ Connecting the CRT and PCB For combining the CRT and PCB, use the specified part No. to maintain the status of adjustments made at the factory. The anode of the CRT itself will be accumulatively charged as time elapses, generating high-tension voltage which is very dangerous. The monitor should be used with the Chassis, CRT and PCB assembled. When repair, etc. is required at the time of malfunctioning, be sure to send it in an "as is assembled" condition. If these are disassembled, what's charged to said high tension voltage can be discharged, causing a very hazardous situation. Therefore, under no circumstances should it be disassembled.

Page 67

@ Static Electricity Touching the CRT surface sometimes causes you to slightly feel electricity. This is because the CRT surfaces are subject to static and will not adversely affect tl

CAUTION! @ Installation and removal

he human body.

Ensure that the Magnetizer Coil, FBT (Fly-Back Transformer), Anode Lead and Focus Lead are not positioned close to the sheet metal work's sharp edges, etc. and avoid damaging the insulated portions so as not to cause electric shock and malfunctioning. (For the name of parts, refer to the above Figures).

Page 68

For the purpose of static prevention, special coating is applied to the CRT face of this product. To protect the coating, pay attention to the following points. Damaging the coating film can cause electric shock to the customers.

CAUTION!

@ Do not apply or rub with a hard item (a rod with pointed edge, pen, etc.) to or on the CRT surfaces.

@ Avoid applying stickers, seals, etc. on the CRT face. . Aluminum Foil @ Do not remove aluminum foils from the CRT corners. Removing the aluminum foils can cause static prevention effects to be lowered.

11 -2 CAUTIONS TO BE HEEDED WHEN CLEANING THE CRT SURFACES

Static preventive coating is applied to the CRT surfaces. When cleaning, pay attention to the following points. Peeling off of static preventive coat can cause

CAUTION! electric shock.

@ Remove smears by using a dry, soft cloth (flannels, etc.). Do not use a coarse

gauze, etc. @ For smear removing solvent, alcohol (ethanol) is recommended. When using chemical detergent, be sure to follow instructions below: Dilute chemical detergent with water and dip a soft cloth in and then thoroughly wring it to wipe smears off. Do not use a chemical detergent containing an abradant, powder or bleaching agent. Do not use alkaline chemical detergents such as "glass cleaner" available on the market or solvents such as thinner, etc. Do not rub or scratch the CRT face with hard items such as brushes, scrub rush, etc.

Clean the CRT surfaces once a week. When cleaning, pay attention to the above caution so that the antistatic coating will not come off.

Page 69
  • COIN SELECTOR

HANDLING THE COIN JAM

If the coin is not rejected when the REJECT button is pressed, open the coin chute door and open the selector gate. After removing the jammed coin, put a normal coin in and check to see that the selector correctly functions.

CLEANING THE COIN SELECTOR

IMPORTANT

@ Remove and clean smears by using a soft cloth dipped in water or diluted chemical detergent and then squeezed dry. Never apply machine oil, etc. to the Coin Selector. After cleaning the Coin Selector, insert a regular coin in the normal working status and ensure that the Selector correctly functions.

The coin selector should be cleaned once every 3 months. When cleaning, follow the procedure below: Turn the power for the machine OFF. Open the coin chute door.

@ Open the gate and dust off by using a soft brush Remove and clean smears by using a soft cloth

(made of wool, etc.).

dipped in water or diluted chemical detergent and then squeezed dry. Remove the CRADLE. When removing the retaining ring (E ring), be very careful so as not to bend the rotary shaft. Remove stain from the rotary shaft and shaft receiving portions by wiping off with a soft cloth, etc.

© After wiping off as per © above, further apply

a dry cloth, etc. to cause the coin selector to dry completely.

COIN INSERTION TEST

Once every month, when performing the Coin SW Test, simultaneously check the following: Does the Coin Meter count satisfactorily? | |Does the coin drop into the Cashbox correctly? Is the coin rejected when inserted while keeping the Reject Button pressed down? Insert a coin while keeping the Reject Button pressed down and check if it is rejected.

Page 70

£9

WELLS-GARDNER WGD15-2110-01

ELECTRONICS CORPORATION OVER/UNDER MINI DOOR

2701 N.KILDARE CHICAGO, IL 60639 2 ENTRIES WITH BILL

1-800-336-6630 WIWW.WGEC.COM VALIDATOR BOTTOM DOOR

& SPECIAL ENCLOSURE

# WG.PART DESCRIPTION Tease | STIR ETT

Z|areaRc oT[STO CET

Eo co

786 TFS

Fa SRTRLORN

aalTRENTO

7a TE

= a ET 3 aT aT | RENT ST oasTEraT | ETAT Tara RE

rT occa

TEBaro|OTE

a TERRE REET

is EREOTORS ECT

i EREOTONTS CAAT

7 Se

i TP TEDSEARESTOTT

D ANG EATON

2 STOVE, WOH a FEET BEL MON 2 ETOP

3 Te TTT

a HOSNTOSST

a SRENAATHEROWS

ED TNT ED TEE OD SHER ED EEC OF AREA

HE BRET ROSTER

oF TOTO

ED TTT

ED CORT

Ey aad

a] BETES ECT a | BEES | SEE ST ar] BETOOET ST FANE

5Daarao aS

TTT — aor

|BETOETTRET TATE

2 ETRE | RG COERSE 3 BETRE TO —— BRT EDT

Page 71

Tom Happ Ph: 847-593-6161 ext. 107 tom.happ@happcontrols.com Fx: 847-956-2091 Happ Controls, 106 Garlisch Drive, Elk Grove, IL 60007 Visit our website http://www.happcontrols.com

42-0641-00 = 42.0405-00 FOR §.25 COIN 42-0405-05 FOR $1.00 COIN O..... 00

42-1044-010 $1.00 4 x .25 1 PLAY 91-1319-00 42-0288-00 (/ 42-0895-05 $1.00 PUSH TO REJECT 43-0047-00 42-0351-00 ated ne 42-7201-00

t 42-0119-00 43-1002-00.

43-1003-00. 42-7355-00: 42-0232-00

$0.25 42-3079-00 $1.00 42-3113-00

@a— 41-0021-00

42-7087-00-

43-40196-00—or

42-6178-00

—— = 42-8174-10 42-0626-00

42-0082-00

Li eA | 42-8177-00

42-8176-00 Guardian Hasp 30-2400-200

Page 72

OPTIONAL DOLLAR BILL ACCEPTOR

@ THE COIN DOOR ASSEMBLY USED ON WILD RIDER STD COMES

EQUIPPED TO ACCEPT A DOLLAR BILL ACCEPTOR. ALL NEEDED WIR- ING CONNECTIONS ARE CONVIENENTLY LOCATED INSIDE THE GAME FOR THIS APPLICATION.

@ THE COIN DOOR CAN ACCCOMMODATE THE FOLLOWING

VALIDATOR(S):

FORWARD-MOST Mars 2000 series

HOLE POSITION

**42-1155-00 MARS VALIDATOR $1, 2,5 300 CAP

The frame and cashbox enclosure on this coindoor has been modified to accomodate a Mars 2000 series upstacker. A 2000 series stacker can be added by simply removing the cut-out plate. This one entry door can be ordered through Happ Controls or one of Happ Controls authorized distributors. The part number is 40-6000-10EX. The Mars stacker can be obtained through an autherized Mars distibutor.

Note: Your game may have either Happ Controls Coin Door Assembly or the Wells Gardner Coin Door Assembly (not shown).

**Happ part number

Security Locking Bar/Bracket Set Part No.# 999-0966

Modified Cash Box (For use when DBA installed)

Part No. # 999-1106

Page 73

**Coin door shown with optional dollar bill validator inserted**

Page 74
  • PERIODIC INSPECTION TABLE

The items listed below require periodic check and maintenance to retain the performance of this machine and to ensure safe business operation.

WARNING! and electric shock hazards. @ Be sure to check once a year to see if Power Cords are damaged, the plug is securely inserted, dust is accumulated between the Socket Outlet and the Power Plug, etc. Using the product with dust as is accumulated can cause fire

Periodically once a year, request the place of contact herein stated or the Distributor, etc. where the product was purchased from, as regards the internal cleaning. Using the product with dust as

without cleaning can cause a fire or accident. Note that cleaning the interior

parts can be performed on a pay-basis. is accumulated in the interior

TABLE 13

TtemIntervalReference

CABINET Check Adjusters'contact with surface. Daily 2

CONTROL PANELCheck lamps.Monthly8-3
Check VOLUME value.Monthly8-3
GreasingTrimonthly9-4

REAR BRAKE Check VOLUME value. Monthly 8-3

GreasingTrimonthly10-3
MONITORCheck adjustments.Monthly or when moving.5,8-2,11
Cleaning of CRT surfaces.Weekly11-2

COIN SELECTOR Check COIN SW. Monthly 8-2

Coin insertion test.Monthly12
Cleaning of COIN SELECTOR.Trimonthly12

GAME BD MEMORY TEST. Monthly 5,8-2

Check settings.Monthly5,8-2,8-3
Cabinet surfacesCleaningAs necessary.See below.
INTERIORCleaningAnnuallySee above.

POWER SUPPLY PLUG| Inspection and cleaning

CLEANING THE CABINET SURFACES

When the cabinet surfaces are badly soiled, remove stains with a soft cloth dipped in water or diluted (with water) chemical detergent and squeezed dry. To avoid damaging surface finish, do not use such solvents as thinner, benzine, etc. or abrasives, bleaching agent and chemical dustcloth.

Page 75
  • TROUBLESHOOTING

14-1 TABLE OF TROUBLESHOOTING

@ !n order to prevent electric shock and short circuit hazards, be sure to turn power off before performing work. Be careful so as not to damage wirings. Damaged wiring can cause electric shock or short circuit. waRNINe! || @ @ After removing the cause of the functioning of the Circuit Protector, reinstate the Circuit Protector. Depending on the cause of the functioning, using the Circuit Protector as is without removing the cause can cause generation of heat and fire hazard.

In case a problem occurs, first check wiring connector connections.

TABLE 14. La

PROBLEMS CAUSE COUNTERMEASURES

When the main SW is | The power is not ON. Firmly insert the plug into the outlet. turned ON, the machine is not Incorrect power source/voltage. Make sure that the power supply/voltage are activated. correct.

The CIRCUIT PROTECTOR functioned After eliminating the cause of overload, have due to momentary overcurrent. the Circuit Protector of the AC Unit restored .

CIRCUIT PROTECTOR CIRCUIT PROTECTOR

RQ Functions due to the activation of bimetal. To restore the function, wait for approximately one minute or longer until the bimetal cools off. (Press the Button.)

FIG. 14.1

Page 76

TABLE 14. 1b

PROBLEMS

The color on the screen is not correct. CAUSE

Incorrect monitor adjustment. COUNTERMEASURES

Make appropriate adjustments.

The on-screen image of the monitor sways and or shrinks. Incorrect power source/voltage.

In sufficient power capacity. Make sure that the power supply/voltage are correct.

Secure sufficient power capacity.

The image is displayed, but the Billboard does not light up. Connection failure between Cabinet and Billboard

Fluorescent Lamp needs replacement. Check the connection of the connector (see 1 , Sec. 5).

Sound is not emitted. Sounds from Speakers and Woofer are not emitted. Sound volume adjustment is not correct.

Sound related Board and Memory are irregular. Adjust the SWITCH UNIT's sound adjustment volume (control) (8-1).

Perform sound and memory test (8-2).

Operation is unsatisfactory. Poor V. R. setting.

V. R. deviation or malfunctioning.

Poor mesh of V.R. GEAR.

Spring failure due to secular change of Handle, Accelerator and Brake mechanism. Perform Volume setting. (8-3)

Adjust or replace the V. R. (see Sec. 9, 10).

Adjust GEAR mesh (see Sec. 9, 10).

Replace the spring.

Page 77

14-2 ERROR MESSAGE

On the screen, the NAOMI2 Board displays errors responding to various troubles when power is turned on or the Test mode closes. The game is not available at this time. When an error is displayed, take action against it according to the appropriate cause and action listed below. Usually no error is displayed unless the settings in the System Test mode have been made erroneously. If a component related to the NAOMI2 Board is replaced with one of another type of game machine, an error may occur.

ERROR 01 [DISPLAY

[CAUSE [COUNTERMEASURES

ERROR 02 [DISPLAY

[CAUSE

[COUNTERMEASURES

ERROR 03 [DISPLAY

[CAUSE [COUNTERMEASURES

ERROR 04 [DISPLAY

[CAUSE [COUNTERMEASURES ERROR 01 THIS GAME IS NOT ACCEPTABLE BY MAIN BOARD. The ROM BOARD is not connected correctly to the MAIN BD. First, turn power off, connect the ROM BD correctly. If the status is not improved yet, the board may be malfunctioning.

ERROR 02 THIS GAME IS NOT ACCEPTABLE BY MAIN BOARD. The destination for the NAOMI2 Board and that for the ROM board are different. Use the main or ROM board that conforms to the destination specification meeting the side of this product. This error cannot be avoided by changing the settings.

ERROR 03 BOARD MALFUNCTIONING. The serial ID on the main board cannot be read. Remove the ROM board from the main body, and send only the main board to us for repair.

ERROR 04 BOARD MALFUNCTIONING. BOOT ROM program cannot read the Main Board's serial ID. Board malfunctioning. Ask for the repair/servicing of ROM BD and MAIN BD.

Page 78
CAUTION 51 [DISPLAY]

[CAUSE] [COUNTERMEASURES]

CAUTION 52 [DISPLAY]

[CAUSE]

[COUNTERMEASURES]

CAUTION 53 [DISPLAY]

[CAUSE]

[COUNTERMEASURES]

CAUTION 54 [DISPLAY]

[CAUSE] [COUNTERMEASURES]

CAUTION 51 GAME ASSIGNMENTS ARE INCORRECT. SET CORRECTLY IN SYSTEM ASSIGNMENTS OF TEST MODE. The CABINET TYPE does not match the settings required for the game. Enter the Test mode, and change the CABINET TYPE setting of SYSTEM

ASSIGNMENTS as suitable for the game. See Section 8-2 for the suitable

setting.

CAUTION 52 CHANGE VIDEO OUTPUT OF THIS GAME TO THE SETTING CORRESPONDING TO HORIZONTAL SCANNING FREQUENCY 15KHz. Though the game is specialized for use with a horizontal frequency of 15 kHz, it is operating with 31 kHz. Set the monitor to 15 kHz, and turn on dip switch No. 1 on the NAOMI2 main board. If your monitor is not available for 15 kHz, this game does not work on it.
CAUTION 53 CHANGE VIDEO OUTPUT OF THIS GAME TO THE SETTING CORRESPONDING TO HORIZONTAL SCANNING FREQUENCY 31KHz. Though the game is specialized for use with a horizontal frequency of 31 kHz, it is operating with 15 kHz.

Set the monitor to 31 kHz, and turn off dip switch No. 1 on the NAOMI2

main board. If your monitor is not available for 31 kHz, this game does not work on it.

CAUTION 54 GAME ASSIGNMENTS ARE INCORRECT. SET CORRECTLY IN SYSTEM ASSIGNMENTS OF TEST MODE. The MONITOR TYPE does not match the settings required for the game. Enter the Test mode, and change the CABINET TYPE setting of SYSTEM

setting. Perform replacement between length and breadth if it is required for the monitor.

Page 79
  • GAME BOARD

@ !n order to prevent electric shock and short circuit hazards, be sure to turn power off before performing work.

WARNING! @ Be careful so as not to damage wirings. Damaged wiring can cause fire, electric shock or short circuit. @ Do not expose the Game BD, etc. without a good reason. Failure to observe this can cause electric shock hazard or malfunctioning.

need not be operated. Use the Game BD, etc. as is with the same setting made at /\ In this product, setting changes are made during the test mode. The Game BD the time of shipment so as not to cause electric shock and malfunctioning.

CAUTION!

15 - 1 TAKING OUT THE GAME BOARD

Turn power OFF by using the Main SW of AC Unit or the SUB PWR SPLY SW inside the SERVICE DOOR.

@ When the power is turned OFF with the Main SW, unlock and remove the SERVICE DOOR.

Disconnect all of the Connectors connected to the Filter Board at the front of the Shield Case, 3 Connectors on the left-hand side facing the Shield Case and the right-hand side Connector.

SCREW (4) [M4 X16, wiflat & spring washers

Disconnect the Connector. eee

THUMBSCREW (L M4 X25, flat washer used. \

Page 80

® Take out the thumbscrew securing the Base, and remove the Base from the cabinet with the Shield Case as is mounted. When removing the Base, first withdraw the Base towards you up to the notch portions allowing for evading the fitting which secures the Base. From that position, lift up and remove the Base. At this time, be very careful so as not to damage wiring.

THUMBSCREW

Fitting to secure the BASE

Move towards you.

Lift up. Notch portion of BASE

mo See

FIG. 15.1b

®Take out the 4 screws and remove the Shield Case.

Page 81

15 - 2, COMPOSITION OF GAME BOARD

this may cause functioning not suitable for the actual operation, or malfunctioning.

S Ensure that the DIP SW setting is performed as designated. Failure to observe

IMPORTANT

ASSY CASE NAO2 WRD USA (840-0046D-01) : USA ASSY CASE NAO2 WRD EXP (840-0046D-02) : OTHERS ASSY CASE NAO2 WRD KOR (840-0046D-03) : KOREA ASSY CASE NAO2 WRD AUS (840-0046D-04) : AUSTRALIA

SCREW (4) ao rome plated

ROM CASE NAO2 WRD 840-0046C

vwsw ASSY CASE NAOMI2 MAIN BD USA(840-0046A-01):USA ASSY CASE NAOMI2 MAIN BD EXP(840-0046A-02):OTHERS ASSY CASE NAOMI2 MAIN BD KOR(840-0046A-03):KOREA AASSY CASE NAOMI2 MAIN BD AUS(840-0046A-04): AUSTRALIA

FIG. 15.2a

DIP SW SETTING

fh the product, set all of the DIP SWes to OFF.

wggg 1234

FIG. 15.2b

Page 82

15 - 3 REPAIR/SERVICING AND CARTON BOX

When transporting NAOMI 2 for repair/servicing, follow the instructions below. The accessory carton box is needed when transporting NAOMI 2 for repair/servicing. Be sure to safely store the Carton Box.

+ When sending for repair/servicing, remove all of the wire harnesses and cables from the Filter BD in front.

+ When transporting NAOMI 2 Main BD for the repair/servicing, ensure that the ROM BD used is in an as is installed status.

+ When sending the NAOMI 2 Main BD for repair/servicing, be sure to put it in the accessory carton box together with the Shield Case. The Main Board (Shield Case) and carton box have an identical serial number. When sending, ensure that the combination seral number is identical with each other.

+ When putting NAOMI 2 SHIELD CASE in the carton box, the Leg Bracket need not be removed.

+ By paying careful attention to the following Figure and the direction shown by on-Carton- Box printing, put the Shield Case in the Carton Box.

  • The projected portions of the packing material is intended for cushioning. Therefore, do not bend the projected portions.

FILTER BOARD/

Projected portions of

FIG. 15.34

Page 83

REMOVING AND REINSTALLING THE ROM BOARD

Ensure that the power is off before preforming work.

+ REMOVING

Disconnect all of the wirings connected to NAOMI 2, and remove NAOMI 2 from inside the cabinet.

@ Remove the 4 screws which secure the ROM BD Case on NAOMI 2 Case.

@Remove ROM BD Case upward by holding both sides.

+ INSTALLING

® Make sure that the connector direction is correct, and insert the ROM BD Case fully onto NAOMI 2 Main BD.

@ By using the 4 screw previously removed as per REMOVING @ above, secure ROM BD Case to NAOMI 2 Case

Case to NAOMI 2 Case.

TRUSS SCREW (4) MB X 30, chrome plated

ROM BOARD

WHEN INSTALLING, BE CAREFUL OF THIS DIRECTION!

FIG. 15.3b

Page 84

POP DISPLAY DECAL CABINET 999-1150

SIDE LEFT 999-1153 HOLDER POP PANEL 999-1151 DECAL BEZEL RIGHT INSTRUCTION 999-1155 DECAL LOWER GETAWAY 999-1157 TIRE TREAD FLAT DECAL 999-1164

DECAL FRONT MAN 999-1160 DECAL LEFT SIDE COIN BOX DECAL SEAT 999-1162 LEFT SIDE 999-1165 MARQUEE, 999-1152 DECAL CABINET SIDE RIGHT 999-1154

DECAL UPPER BONUS/GAME OVER 999-1156 DECAL BEZEL LEFT INSTRUCTION 999-1158 DECAL CONTROL PANEL DECAL FRONT DECAL RIGHT SIDE WOMAN COIN BOX 999-1161

999-1163

DECAL SEAT RIGHT SIDE, 999-1166

  • DESIGN RELATED PARTS
Page 85
  • PARTS LIST Q@ TOP ASSY WRD

PART NO.

WRD-2500 CTA-1650

999-1167 999-1168 999-1065 LOC. PURCHASE

999-1170 999-0169 999-0167 999-1169 DESCRIPTION

ASSY HANDLE BRAKE UNIT SEAT CABI FOOT REST VENT -4 HOLE AIR BLACK PDRCOAT VENT -8 HOLE AIR BLACK PDRCOAT WOOFER 29 INCH MONITOR, CABINET AC UNIT 27° BEZEL CASTER LEG LEVELER COVER FOOT REST

Page 86

Details of) ®

Wo

@) ASSY HANDLE (WRD

2500) (D-1/2)

Page 87
  • ASSY HANDLE (WRD-2500)

ITEM NO. PART NO.

1 WRD-2550 2 WRD-2600 3 HLD-2002 4 MJT-3603X 5 MJT-3612 6 WRD-2501 7 WRD-2502 8 WRD-2503 9 WRD-2504 10 WRD-2505

101 280-6623-1S-0

201 000-T00412-0B 202 020-000620-0Z 203 060-F00600-0B 204 060-S00600-0B 205 000-T00310-0C 206 050-F00300 207 060-F00300-0B (D-2/2)

DESCRIPTION

ASSY BRAKE MEDHA ASSY THROTTLE GRIP LEFT MOUNT BLOCK HANDLE HOLDER HANDLE BAR WIRE MOUNT PLATE WIRE STAY HOLE LID STICKER MASTER CYLINDER

PLASTIC TIE BELT PLT-1S-0

M SCR TH BLK M4 X 12 HEX SKT H CAP SCR BLK 0Z M6 X 20 FLT WSHR BLK M6 SPR WSHR BLK M6

M SCR TH CRM M3 X 10

FLG NUT M3 FLT WSHR BLK M3

Page 88

G) ASSY CENTERING BASE (WRD-2100) (D-1/2)

a

9 \ (201 (202 (4 (Re ( 2) I A (YD) (9) / \

Light Receiving Side O (il r fl Oo Light Emitting Side

\ L — . — ; / \ a /

\ \/

/

  • ©|,

4 \. (492% AD (202 ( c \ £203,204 (205) (4) 207208 QS AD ALVA KEY 4 ix AIA LTE)

© The tightening torque to each screw shall be 2.45 Nem.

Page 89
  • ASSY CENTERING BASE (WRD-2100) (D-2/2)

ITEM NO.

DIDNEWNHHK

2u1 PART NO.

WRD-2101 WRD-2102 WRD-2103 WRD-2104 WRD-2105 100-5050 421-7226-12-91 421-7226-21-91

370-5232 280-0419

000-P00410-S 060-F00400 050-U00300 060-S00300 060-F00300 050-U00600 000-P00312-W 050-H00300 000-P00408 060-S00400

WRD-60003 DESCRIPTION

FRONT COVER CENTERING ARM L CENTERING ARM R SW BRKT SPRING HOLD ROLLER BEARING 19 STICKER L LONG STICKER U LONG

PHOTO SENSOR OMT-01DS HARNESS LUG

MSCR PH W/S M4 X 10 FLT WSHR M4 U NUT M3 SPR WSHR M3 FLT WSHR M3 U NUT M6 M SCR PH WIFS M3 X 12 HEX NUT M3 MSCR PH M4 X8 SPR WSHR M4

WH CENTERING MECHAOI

Page 90

G) ASSY HANDLE MECHA (WRD-2000) (D-1/3)

(a) OL2

_-\_ Toward VOLUME D-Cut

Page 91

() ASSY HANDLE MECHA (WRD-2000) (D-2/3)

ITEM NO. PART NO.

WRD-2100 WRD-2001 WRD-2002 WRD-2003 WRD-2004 WRD-2005 WRD-2006 WRD-2007 WRD-2009 WRD-2010 WRD-2011 WRD-2012 WRD-2013 WRD-2014 WRD-2015 WRD-2016 WRD-2017 WRD-2018 WRD-2019 WRD-2020 WRD-2021 WRD-2022 WRD-2023 WRD-2024 WRD-2025 WRD-2026 601-6555 601-6450 601-10999 100-5071

220-5373 310-5029-F20 280-5009 DESCRIPTION

ASSY CENTERING MECHA STOPPER BRKT STOPPER SHAFT STOPPER ROT MAIN SHAFT SHAFT HOLDER UPPER SHAFT HOLDER LOWER SW SHADE HOLD CAM SPRING SUS SPRING HOOK GUIDE SHAFT GUIDE BLOCK STOPPER HOLDER STOPPER PP REAR COVER VR BRKT MECHA COVER MECHA BASE BASE BRKT ROSTA BASE ROSTA HOLDER GEAR BASE GEAR NUT PLATE HIDE PLATE TOP COVER GEAR Z=30 M=0.75 GEAR 110 TORSION RUBBER KURASHIKI 18 X 30 BEARING 30

VOL CONT B-SK SUMITUBE F F 20MM CORD CLAMP 21

Page 92

G) ASSY HANDLE MECHA (WRD-2000) (D-3/3)

ITEM NO. PART NO.

030-000820-S 050-H00800 060-S00800 060-F00800 000-P00416-W 000-P00420-S 029-0427 000-P00408-W 060-S00400 060-F00400 000-P00612-S 060-F00600 060-S00600 050-U00600 050-H01200 060-F01200 060-S01200 028-C00412-P 028-C00406-P 065-S025S0-Z 000-P00412-W 000-P00512-W

WRD-60004 DESCRIPTION

HEX BLT W/S M8 X 20 HEX NUT M8 SPR WSHR M8 FLT WSHR M8 M SCR PH W/FS M4 X 16 M SCR PH W/S M4 X 20 HEX SKT H CAP SCR M4 X 10 MSCR PH W/FS M4 X 8 SPR WSHR M4 FLT WSHR M4 MSCR PH WIS M6 X 12 FLT WSHR M6 SPR WSHR M6 U NUT M6 HEX NUT M12 FLT WSHR M12 SPR WSHR M12 SET SCR CH CUP P M4 X 12 SET SCR CH CUP P M4 X 6 STP RING BLK 0Z S25 M SCR PH W/FS M4 X 12 M SCR PH W/FS MS X 12

WH HANDLE MECHAOIL

Page 93

(D-1/2)

(S) ASSY BRAKE MECHA (WRD-2550)

5 IK / a / GREASING

i Tone, aN ~ (301 1) (1 Ia ) iM ) (10)

Ka

SCREW, NUT FASTENING TORQUE TO BE M4: 1.8 Nem M6: 7.3 Nem Grease the gear and sliding section.

ou

Page 94

(S) ASSY BRAKE MECHA (WRD-2550) (D-2/2)

ITEM NO.

CoOIDAHARwWNHY PART NO.

HLD-2501 HLD-2502 HLD-2503 HLD-2504 HLD-2505 HLD-2506 HLD-2507 HLD-2508 HLD-2509 WRD-2551 280-6619 HLD-2512 HLD-2513 HLD-2514

220-5484 601-7944 310-5029-F20 280-5275-SR10

000-T00408-0B 050-C00400-3B 000-P00408-W 030-000620-SB 028-A00306-P FAS-500015 065-S016H0-Z 068-441616 060-F00600-0B 000-P00408 060-S00400 060-F00400

WRD-60006 DESCRIPTION

BRAKE MASTER CASE MASTER CASE HOLDER MASTER CASE COVER BRAKE GEAR IDOL GEAR PIVOT SHAFT VR BRKT LEVER STOPPER IDOL GEAR SHAFT MASTER PISTON RUBBER FOOT T 3G BRAKE LEVER VR COVER RETURN SPRING

VOL CONT B-SK OHM GEAR 15 SUMITUBE F F 20MM CORD CLAMP SR10

MSCR TH BLK M4 X8 CAP NUT TYPE3 BLK M4 MSCR PH W/FS M4 X 8 HEX BLT W/S BLK M6 X 20 SET SCR HEX SKT CUP P M3 X 6 CAP NUT BLK M6 STP RING BLK OZ H16 FLT WSHR 4.4-16 X 1.6 FLT WSHR BLK M6 M SCR PH M4 X8 SPR WSHR M4 FLT WSHR M4

WH BRAKE MECHAOIL

Page 95

SCREW FASTENING TORQUE TO BE

M3: 0.75 Nem M4: 1.8 Nem Grease the gear section.

  • ASSY THROTTLE (WRD-2600) (D-1/2)
Page 96
  • ASSY THROTTLE (WRD-2600) (D-2/2)

ITEM NO.

CoOIDAHARwWNHY PART NO.

HLD-2601 HLD-2602 HLD-2603 HLD-2604 HLD-2605 HLD-2606 HLD-2607 HLD-2608 HLD-2609 HLD-2610 HLD-2611 HLD-2612 HLD-2613 HLD-2614

220-5484 601-7944 310-5029-F20

000-T00408-0B 000-P00408-W 000-F00408 030-000625-SB 060-F00600-0B 028-A00306-P 012-P00306 000-P00408 060-S00400 060-F00400

WRD-60005 DESCRIPTION

THROTTLE CASE LOWER THROTTLE CASE UPPER INNER GRIP ACCEL GEAR BASE PLATE ACCEL GEAR SHAFT ACCEL VR BRKT SPRING HOOK RETURN SPRING VR COVER ACCEL GRIP SLIDE PLATE SPRING STOPPER GEAR SPRING

VOL CONT B-SK OHM GEAR 15

SUMITUBE F F 20MM

MSCR TH BLK M4 X8 MSCR PH W/FS M4 X 8 M SCR FH M4 X8 HEX BLT W/S BLK M6 X 25 FLT WSHR BLK M6 SET SCR HEX SKT CUP P M3 X 6 TAP SCR #2 PH3 X6 M SCR PH M4 X8 SPR WSHR M4 FLT WSHR M4

WH THROTTLEO1

Page 97

se) ° @

GREASING \ ‘Bo

GREASING

[~~ GREASING (@) BRAKE UNIT (CTA-1650) (D-1/2)

Page 98

@) BRAKE UNIT (CTA-1650)

ITEM NO. PART NO.

1 CTA-1601 2 CTA-1651 3 CTA-1603 4 CTA-1604 5 CTA-1605 6 CTA-1606 7 CTA-1607 8 HLD-2805 9 HLD-2808 10 601-6450 ll 601-7944 12 CTA-1608

101 220-5373 220-5484 102 310-5029-F20 103 280-0419

201 000-P00412-W 202 000-P00408-W 203 050-U00800 204 060-F00800 205 028-A00308-P 206 020-0004 16-0Z 207 060-S00400 208 050-F00400 209 020-000408-0Z 210 060-F00400

301 CTA-60050 (D-2/2)

DESCRIPTION

PEDAL BASE BRAKE PEDAL. PEDAL SHAFT STOPPER BLOCK RUBBER PLATE RUBBER CASE VR BRKT TORSION SPRING RUBBER HOLDER GEAR 110 GEAR 15 SUPPORT BRKT

VOL CONT B-5K VOL CONT B-SK OHM SUMITUBE F F 20MM HARNESS LUG

M SCR PH W/FS M4 X 12 MSCR PH W/FS M4 X 8 U NUT M8 FLT WSHR M8 SET SCR HEX SKT CUP P M3 X 8 HEX SKT H CAP SCR BLK 0Z M4 X 16 SPR WSHR M4 FLG NUT M4 HEX SKT CAP SCR BLK 0Z M4 X 8 FLT WSHR M4

WIRE HARN BRAKE

Page 99
  • SEAT CABI

ITEM NO.

ANRWNE PART NO.

999-1171 999-1172 999-1173 999-0167 999-1174 999-1175 DESCRIPTION

COVER SEAT VACUUM FORM FENDER VACUUM FORM S/A; SEAT & FENDER LEG LEVELER WOOD DOOR SEAT PLATE TREAD

Page 100
  • SW UNIT (CTA-1160)

ITEM NO. PART NO. DESCRIPTION

1LOC. PURCHASE5 K POTENTIOMETER & VOLUME KNOB
2LOC. PURCHASEMOM. PUSH BUTTON SW
3LOC. PURCHASECOIN METER 6 VOLTS
Page 101
  • ASSY MAIN BD

ITEM NO.

DIDKARWNHHE PART NO.

837-13551-92 400-5397-01 838-13759 838-11651-01 838-13616 600-7009-3000 840-0046D-01 600-7141-200

Note: Make sure that there is no parts, wiring, etc. in the slash mark portions. 4)

DESCRIPTION

1/0 CONTROL BD POWER SUPPLY FOR JVS RECT BD CTA PC BLOW PASS AMP w/LARGE HEAT SINK AUDIO POWER AMP 2 CH ASSY RGB CABLE SUB 15P. ASSY CASE NAO2 WRD US USB CABLE

Page 102

(il) ASSY XEMR (NOB-4100)

ITEM NO.

RON PART NO.

998-0147 998-0146 LOC. PURCHASE LOC. PURCHASE

Note: Make sure that there is no parts, wiring, etc. in the slash mark portions.

DESCRIPTION

TRANSFORMER 12V HA MCI-4-06-7012 TRANSFORMER MCI 4-06-8036 FUSE BLOCK LINE FILTER 6 AMP

Page 103
  • WIRE COLOR CODE TABLE

THE WIRE COLOR CODE is as follow:

moawp PINK

SKY BLUE

BROWN

PURPLE

LIGHT GREEN

Wires other than those of any of the above 5 single colors will be displayed by 2 alphanumeric characters.

CerIKNRwWNe RED

BLUE

YELLOW

GREEN

WHITE

ORANGE

BLACK

GRAY

If the right-hand side numeral of the code is 0, then the wire will be of a single color shown by the left-hand side numeral (see the above).

Note 1:
Note 2: If the right-hand side alphanumeric is not 0, that particular wire has a spiral color code. The left-hand side character shows the base color and the right-hand side one, the spiral color.

<Example> 51 oe WHITE / RED

RED WHITE

The character following the wire color code indicates the size of the wire.

U: AWGI16

K: AWGI8

L: AWG20

‘None: AWG22

Page 104

VISIT OUR WEBSITE!

© SegaService.com

Por erraal G) hity://www.seuservice.com/

Search criteria:

SERVICE

  • Dari's Office *" What's New
  • Game Manuals *" Bultetins

Sega Enterprises Inc., USA Semwice Department phone 415.701.6580 fax 415.701.6594 { ‘ 11 ! UstaffllDarl's off [technical serice][customer senvice|{corporate info|[plugins][Non-framed page]

A total of EMew 1 people have accessed this page since June Sth.

Ifyou have any questions or comments about this Home Page please E-Mail to

darl davidson@seu sega. com OR dave. cantrelle@seu sega. com

Sega Enterprise Inc., USA. All rights reserved

You will need the following items to view this page in its entirety

Page 105

SEGA ENTERPRISES, INC. (USA)

45133 Industrial Drive Fremont, CA 94538 (415) 701-6580 phone (415) 701-6594 fax