CATHODE RAY TOMES

Killer Instinct Kit (16-44047-101 Jan 1995)

Killer Instinct (Rare / Nintendo (Midway license), 1994) · Manual · 47 pages · 35 sections · original scan

Page 1

MIDWAY JANUARY 1995

eC 16-44047-101

KILLER INSTINCT

KIT

MANUAL - includes

  • includes -

installation & operation parts information wiring diagrams

Page 2

KILLER INSTINCT

KIT

MIDWAY Manufacturing Company reserves the rights to make modifications and improvements to its products. The specifications and parts identified in this manual are subject to change without notice.

Page 3

TABLE OF CONTENTS Section 1 Operation and Troubleshooting

Notice - FCC Warning Sticker Inspection...

Control Panel Modifications. Install the PC board, Hard Drive & Fan into a JAMMA Cabine' Install the PC board, Hard Drive & Fan into a NON-JAMMA Cabinet Game Feature: 1-10 Starting-up. 1-10 Player Controls. 1-10 Control Panel Diagram. 1-11 Menu System Operation.. Operation... 1-11 Main Menu. 1-12 Diagnostic Tests. 1-12 Switch Test.. 1-13 DIP Switch Test & Table. 1-14 CPU Board Test.. 1-14 Sound Board Tes’ 1-15 Monitor Patterns Test. 1-16 Check Disk... 1-16 Burn-in Test.. 1-17 Coin Bookkeeping. 1-18 Game Audit: 1-23 Game Adjustment 1-25 Standard Pricing. 1-26 Custom Pricing Utilitie Volume Troubleshooting.................

Section 2 Parts Information CPU/Sound Board.....ccssecsesssnsessseessceeeseens ae Hard Drive Mounting Bracket & Complete Hard Drive Assembly Diagram. Fan, Fan Mounting Bracket & Complete Fan Assembly Diagram...........

Section 3 Diagrams and Schematics 3-2 JAMMA Chart. Interboard Wiring Diagram. Coin Switch and Meter Wirin: Cabinet Wiring Diagram. Electronic Rack Assembly. Templates.

Killer Instinct™ ©1994 Nintendo/Rare Game by Rare Killer Instinct is a trademark of Nintendo Manufactured and sold by Midway Manufacturing Company under license.

Page 4

KILLER INSTINCT

KIT

SECTION one

Operation

Page 5

SAFETY NOTICES The following safety instructions apply to all kit operators and service personnel. Specific warnings and cautions will be found throughout this manual where they apply. We recommend that you read this page before preparing your kit for play. eS es /\. CAUTION

HARD DRIVE. The operator must retain the special shipping box and antistatic bag that the hard drive is packed in. The hard drive must be repacked in its origina! container before returning to the distributor for replacement or repair. The hard drive must be removed from the game cabinet and repacked into its original container BEFORE the game cabinet is moved to a new location. If the original shipping box and antistatic static bag is lost or destroyed, a replacement can be order from the distributor. Shipping Box #08-7936, Anti-Static Bag #20-9638-3

FAN. The fan must be connected to a fused 110V power source.

SALVAGED PARTS. Parts salvaged from old games are required to complete your kit. These salyaged parts must operate perfectly: otherwise, the converted game cannot perform properly or safely. Always repair circuit board malfunctions and cabinet damage before conversion is attempted.

POWER SUPPLY. Be sure the power supply from your old game is capable of +5VDC at 5A, -5VDC at 1A and +12V at 2A. These operating voltages are necessary for the kit. Your power supply must be FCC approved.

MONITOR. This kit is not intended for use with X-Y monitors. Suitable monitors have horizontally mounted CRTs and raster electronics with inputs for red, green and blue video, as well as COMPOSITE NEGATIVE SYNC inputs.

COIN MECHANISM. Be sure to clean and lubricate your old coin mechanisms. Servicing them is crucial to your game's earning potential and operation.

COIN METERS. Coin meters are not provided with this kit. Wiring information is provided as a convenience to the operator.

DISCONNECT POWER DURING INSTALLATION OR REPAIRS. To avoid electrical shock, disconnect the game from the AC power source before attempting to service or install your kit.

ATTENTION !

PROPERLY ATTACH ALL CONNECTORS. Be sure that the connectors on each printed circuit board (PCB) are properly connected. If they do not slip on easily, do not force them. A reversed connector may damage your game and void the warranty. All connectors are keyed to fit specific pins on each board.

1-2

Page 6

NOTICE - FCC WARNING STICKER |. THIS KIT WAS TESTED IN A MIDWAY UNIVERSAL VIDEO CABINET AND FOUND TO COMPLY WITH FCC PART 15 CLASS A REQUIREMENTS. IF INSTALLED IN MIDWAY UNIVERSAL VIDEO CABINET, THE FCC WARNING STICKER (16-9306) SUPPLIED IS TO BE PLACED ON THE REAR OF THE CABINET. Il. INSTALLATION OF THIS KIT INTO ANY OTHER PRODUCT DOES NOT GUARANTY COMPLIANCE WITH FCC REQUIREMENTS. YOU ARE SOLELY RESPONSIBLE, AND MIDWAY WILL HAVE NO RESPONSIBILITY, FOR FCC COMPLIANCE FOR IN- STALLATIONS IN OTHER PRODUCTS. THE FCC WARNING STICKER SUPPLIED SHOULD NOT BE INSTALLED ON THE CONVERTED PRODUCT UNTIL FCC COM- PLIANCE IS VERIFIED.

CONVERSION PROCEDURE

INSPECTION Unpack the materials from the carton and inspect for obvious signs of damage. Use this checklist to be sure the kit is complete.

Part NumberltemQuantity
(A-19595.1hard drive mounting bracket1
0]A-19596programmed hard drive1
[]A-19650-40047CPU/Sound board assembly1
[A-19806fan mounting bracket2
[H-19960main JAMMA cable1
U]H-19961auxiliary (control panel) cable1
[03-8338-11/4" PCB mounting spacers7
[03-9223fan guard - plastic1
[08-7936hard drive shipping box1
(]16-9306FCC Warning Sticker1
[116-9922Epilepsy Warning Label1
[20-9420fan grille - metal1
20-9620key T-20 TR-TX long arm1
20-9638-3hard drive anti-static bag1
if20-9687-3blue pushbuttons12
[20-9687-2white pushbuttons2
]20-9947fan4
20-10178-38-way joysticks2
[20-10180fan AC cable1
]20-10188truss head phillips screws4 (to attach hard drive to mounting bracket)
]31-1789clear overlay1
[31-2020-1screened marquee1
31-2229side panel decal2
]31-2311screened overlay1
[31-2312decal set1
[4006-01192-346-32x2-1/8 machine screws4 (to attach grille, guard & fan to mtg brkt)
]4108-01092-10Btorx head sheet metal screws10 (to attach clear overlay to contro! panel)
4308-01123-24B8-32x1-1/2 bolts8 (to attach joysticks to control panel)
if4408-01128-008-32 nuts8 (to attach joysticks to control panel)
4700-00090-00Bflat washers .156x.375x.03010 (to attach clear overlay to control panel)
5556-13956-00ferrite bead 2 piece 1-1/4"1
[5556-14510-00ferrite bead flat cable type2
[5795-14459-00ribbon cable 2-1/8"1

FBI Label 1 ] Always install PC boards and hard drive as shown in Electronic Rack Assembly drawing, (page 3-6). 1-3

Page 7

CONVERTING FROM A TYPICAL VIDEO GAME CABINET

Recommended tools and supplies

[] U] {]

0] 0] black semi-gloss paint [ ] black electrical tape electric drill [ ] surplus assorted screws electric screwdriver [ ] wire cutters grease pencil or marker [ ] soldering iron and solder hex driver [ ] razor knife 180 grit sandpaper or electric sander

CABINET MODIFICATIONS

1. Repaint the cabinet with black semi-gloss paint (games with wood grain sides: remove the old decal and artwork and clean the glue residue before painting). Allow paint to dry.

Pencil a line roughly at the top of the old graphic. Lightly moisten the cabinet with soapy water. Apply the decal starting at the top and working down. After the decal is in place, smooth it down, taking care to squeeze out air bubbles. If you miss an air bubble, pop it with a razor knife or a pin and burnish it down. Allow 12 hours for the adhesive in the decal to set. Remove the masking.

Remove the marquee from the game cabinet and install the KILLER INSTINCT marquee in its place.

Place Epilepsy Warning Label on the front of the monitor bezel. Be sure that it does not obstruct the CRT screen, but is in full view of the players.

CONTROL PANEL MODIFICATIONS

Remove the control panel buttons and joysticks and remove the old vinyl covering and artwork.

Use the control panel templates to help you design the control panel. (Templates are the last pages of this manual) Refer to page 1-5 for suggested template layout.

Drill holes, as needed, for the joysticks and control panel buttons. Plug previous holes with wood blocks, putty, cardboard or epoxy. File the new holes smooth.

Carefully remove the backing on the vinyl control panel overlay. Place the overlay on the top of the control Panel. Prevent air bubbles from getting under the overlay.

After the overlay is on securely, use a razor knife to cut holes for the control panel buttons and joysticks.

Position the stickers next to the appropriate hole locations. Refer to page 1-5 for suggested control panel button and joystick sticker locations.

Being careful not to displace the stickers, place the overlay on the control panel. Use the torx head sheet metal screws and flat washers to attach the clear overlay to the control panel. Once the clear overlay is securely in place, cut holes for the joysticks and control panel buttons.

Page 8

Remove the switch from the pushbutton by pulling the large prong away from the switch, then pull the switch off of the housing. Unscrew the nut from the housing. Open the control panel. Push the switch through the front of the panel and screw the nut onto the switch housing from the back of the panel. Snap the switch back onto the housing.

To install the joysticks, first remove the "E"-ring and slide the shaft and the plastic ring off the joystick base. Be sure that the bushings remain in the base. Use the 8-32 bolts and the 8-32 nuts to attach the base to the underside of the control panel. Slide the plastic ring around the shaft so that the rough side is next to the shaft handle. Slide the shaft through the control panel and base. Replace the "E"-ring.

; © O

© a@lOl@) © °O O o- OOO (2) 66

TEMPLATE TEMPLATE

© O

SUGGESTED CONTROL PANEL TEMPLATE LAYOUT (Templates are the last pages of this manual)

Stat (white) Sart (white)

Jump High Attack (all blue) Jump High Attack (all blue)

QuickMediumFierceQuickMediumFierce
MoveMove:©MoveMove©O©
Duck©oO©Duck©)©)©)
QuickMediumFierceQuickMediumFierce

Low Attack (all blue) Low Attack (all blue)

SUGGESTED CONTROL PANEL LAYOUT AND STICKER LOCATIONS FOR A TYPICAL VIDEO GAME CONTROL PANEL.

Page 9

INSTALL THE PC BOARD, HARD DRIVE & FAN INTO A JAMMA GAME CABINET PC board, fan, and hard drive must be installed as shown in Electronic Rack Assembly drawing, (page 3-6).

1.

2. Replace the existing CPU board and sound board with the KILLER INSTINCT CPU/Sound board. Use the 1/4" PCB mounting spacers and surplus screws to secure the CPU/Sound board to the rack.

Install the hard drive using: A-19595.1 hard drive mounting bracket, A-19596 programmed hard drive, 20-10188 truss head phillips screws, 5556-14510-00 ferrite bead, 5795-14459-02 ribbon cable. Screw the four truss head screws part way into the threaded holes on the sides of the hard drive. With the L-slots on the mounting bracket facing down, and the connector on the hard drive facing up, slide the hard drive back and down, into the slots on the bracket. Tighten the truss head screws. Remove one clip from the ferrite bead and slide the bead over the ribbon cable. Replace the clip. Plug the ribbon cable into the connector on the hard drive. With the ribbon cable facing the CPU/Sound board, attach the hard drive mounting bracket, to the rack with surplus screws. Be sure the ribbon cable can reach J6 on the CPU/Sound board. See page 2-3 for diagram. To J6 On CPU/Sound Board

RED LINE GOES TO js PIN. CSsssssesessesscssesssssssn . FERRITE BEAD | cL CLIP teTaL PLATE ON HARD DRIVE

RED LINE Ribbon Cable and Connector (see page 2-3 for detailed diagram)

To Connector On Hard Drive

Install the fan using: A-19806 fan mounting brackets, 03-9223 fan guard, 20-9420 fan grille, 20-9947 fan, 20-10180 fan AC cable, 4006-01192-34 machine screws. Place the grille on the front of the fan, and the guard on the back of the fan. Place the long end of the mounting bracket (one for the left side and one for the right ) behind the guard. Line up the screw holes. Secure together with the machine screws. Be sure that the fan is aligned so that air flows toward the CPU/Sound board and attach the assembly to the rack using surplus screws. Plug fan AC cable into the fan and attach the other end to a fused 110V source. The fan must be powered up anytime the CPU/Sound board is running. See page 2-4 for diagram.

If you choose to use the JAMMA cable provided with the kit, disconnect your old JAMMA cable from the speaker, power supply, control panel switches (may already be disconnected) and coin door. Remove the cable from the game. Leave your power supply chassis as is. NOTE: If you choose to use your own JAMMA cable, check the JAMMA chart to be sure your cable is compatible.

AX CAUTION

Properly insulate any unused wires, within the JAMMA cable, especially the gray, gray-green and gray-yellow wires. This is a fully wired JAMMA cable. Many of the wires will not be used for this kit. These wires have been installed so that you can use this cable for future kits.

Page 10

Connect the JAMMA cable to the CPU/Sound board. Use the Cabinet Wiring Diagram for reference and solder the correct JAMMA cable wires to the speaker. Then, connect the wires to the coin door, power supply and the control panel. Player 1 has white-'color stripe’ wires, except for the Start 1 which has a solid white wire. Player 2 has violet-‘color stripe' wires. Use the Cabinet Wiring Diagram in section 3, or the control panel wire color list on the inside back cover for reference when connecting these wires to the player 1 and 2 control panel switches.

Attach ferrite bead (5556-13956-00) to JAMMA cable. See Electronic Rack Assembly drawing on page 3- 6 for correct bead placement.

Connect the Auxiliary cable to J7 of the CPU/Sound board. Use the Cabinet Wiring Diagram in section 3, or the control panel wire color list on the inside back cover for reference when connecting these wires to the Low/Quick, Low/Medium, and Low/Fierce switches.

Place the FBI Warning Label next to the CPU/Sound board. Be sure the label is completely visible.

Page 11

INSTALL THE PC BOARD, HARD DRIVE & FAN INTO A NON-JAMMA GAME CABINET PC board, fan, and hard drive must be installed as shown in Electronic Rack Assembly drawing, (page 3-6).

  • Replace the existing CPU board and sound board with the KILLER INSTINCT CPU/Sound board. Use the 1/4" PCB mounting spacers and surplus screws to secure the CPU/Sound board to the rack.
  • Install the hard drive using: A-19595.1 hard drive mounting bracket, A-19596 programmed hard drive, 20-10188 truss head phillips screws, 5556-14510-00 ferrite bead, 5795-14459-02 ribbon cable. Screw the four truss head screws part way into the threaded holes on the sides of the hard drive. With the L-slots on the mounting bracket facing down, and the connector on the hard drive facing up, slide the hard drive back and down, into the slots on the bracket. Tighten the truss head screws. Remove one clip from the ferrite bead and slide the bead over the ribbon cable. Replace the clip. Plug the ribbon cable into the connector on the hard drive. With the ribbon cable facing the CPU/Sound board, attach the hard drive mounting bracket, to the rack with surplus screws. Be sure the ribbon cable can reach J6 on the CPU/Sound board. See page 2-3 for diagram. To J6 On CPU/Sound Board RED LINE GOES TO [ms PIN. Ses seessessssSssessesy ese. FERRITE BEAD CLIP CLIP

Teta PLATE ON HARD DRIVE

Ribbon Cable and Connector (see page 2-3 for detailed diagram) RED LINE

To Connector On Hard Drive

3 Install the fan using: A-19806 fan mounting brackets, 03-9223 fan guard, 20-9420 fan grille, 20-9947 fan, 20-10180 tan AC cable, 4006-01192-34 machine screws. Place the grille on the front of the fan, and the guard on the back of the fan. Place the long end of the mounting bracket (one for the left side and one for the right ) behind the guard. Line up the screw holes. Secure together with the machine screws. Be sure that the fan is aligned so that air flows toward the CPU/Sound board and attach the assembly to the rack using surplus screws. Plug fan AC cable into the fan and attach the other end to a fused 110V source. The fan must be powered up anytime the CPU/Sound board is running. See page 2-4 for diagram.

  • Leaving several inches of wire, cut the wires at the coin door, control pane! switches, (which may already be disconnected) speaker and power supply. Remove the harness from the cabinet. Leave your power supply chassis as is. NOTE: Be sure that all spliced wires are well insulated with black electrical tape.
  • Install the JAMMA cable provided with the kit. Players 1 and 2, the coin door, and the power supply wires are bundled together in individual groups. Insure that the cable is properly dressed and supported.

A CAUTION

Properly insulate any unused wires, within the JAMMA cable, especially the gray, gray-green and gray-yellow wires. This is a fully wired JAMMA cable. Many of the wires will not be used for this kit. These wires have been installed so that you can use this cable for future kits.

1-8

Page 12

Connect the JAMMA cable to the CPU/Sound board. Use the Cabinet Wiring Diagram for reference and solder the correct JAMMA cable wires to the speaker. Then, connect the wires to the coin door, power supply and the control panel. Player 1 has white-'color stripe’ wires, except for the Start 1 which has a solid white wire. Player 2 has violet-'color stripe’ wires. Use the Cabinet Wiring Diagram in section 3, or the control panel wire color list on the inside back cover for reference when connecting these wires to the player 1 and 2 control panel switches.

Attach ferrite bead (5556-13956-00) to JAMMA cable. See Electronic Rack Assembly drawing on page 3- 6 for correct bead placement.

Connect the Auxiliary cable to J7 of the CPU/Sound board. Use the Cabinet Wiring Diagram in section 3, or the control panel wire color list on the inside back cover for reference when connecting these wires to the Low/Quick, Low/Medium, and Low/Fierce switches.

Place the FBI Warning Label next to the CPU/Sound board. Be sure the label is completely visible.

Page 13

GAME FEATURES

STARTING UP Switch on power to the game. The game runs through a start-up routine. {Insert the desired amount of coins, bills or tokens. Select which player receives the credit by pressing the appropriate Start button.

NOTE When an error is detected during the Start-up tests, game start-up does not progress, and an error message appears on the screen.

PLAYER CONTROLS Start Button Each player has a Start button. The Start buttons allow one or two players to begin or continue play.

Joysticks Each player has a joystick which he uses to control an on-screen character. The player can make the on-screen character move, jump or duck.

High Attack An attack that originates above the waist, such as a punch.

Low Attack An attack that originates below the waist, such as a kick.

Quick A “quick" attack is a short range, short duration attack that inflicts little damage to an opponent.

Medium A "medium" attack is a moderate range, moderate duration attack that inflicts some damage to an opponent.

Fierce A “fierce" attack is a long range, long duration attack that inflicts much damage to an opponent.

NOTE Use joystick and button combinations to discover secret moves.

CONTROL PANEL DIAGRAM

Stat Sart

Jump High Attack Jump High Attack

QuickMediumFierceQuickMediumFierce

Move Move (©) © (©) Move Move

Duck©©©Duck©©©
QuickMediumFierceQuickMediumFierce

Low Attack Low Attack

Page 14

MENU SYSTEM OPERATION

OPERATION All game audits, adjustments and diagnostics are options of the Main Menu. Each option, in turn, has its own menu that lists several choices which you may act upon as desired.

Close switch #8 of DIP switch bank #2 to open the Main Menu (shown below). Game adjustments, bookkeeping and diagnostics are all accessible from this menu.

Use either joystick to move the cursor up and down the menu screen. Notice that the options are highlighted in sequence. Press any button to open a highlighted option. Only highlighted options can be opened.

To exit the Main Menu, use either joystick to select EXIT TO GAME OVER and press any button.

MAIN MENU

Page 15

DIAGNOSTIC TESTS Use either joystick to select the Diagnostic Menu and any button to open it. Then, use either joystick to move the cursor up and down the menu and any button to open a highlighted option.

DIAGNOSTIC MENU

Switch Test The Switch Test allows the operator to test the switches on the contro! panel and in the coin door.

Use either joystick to highlight the Switch Test and any button to begin the test.

During the Switch Test the top of the screen shows the control panel switches while the bottom of the screen shows the coin door switches. Press a control panel or coin door switch and the switch location on the screen lights. Release the switch and the screen returns to normal.

To exit the Switch Test, press both Start buttons together.

SWITCH TEST SCREEN

1-12

Page 16

DIP Switch Test The DIP Switch Test allows the operator to check or change the position of the DIP Switches on the CPU Board.

Use either joystick to select the DIP Switch Test and press any button to access the DIP Switch Setting Tables. The screen displays the current DIP Switch settings. To change a setting, slide the switch to the desired Position, then check the screen to verify the new setting. In some cases, setting a function to OFF actually enables the function. For example, setting DIP Switch Coinage to Off enables DIP Switch Coinage.

Press any button to return to the Diagnostic Menu.

DIP Switch 1 Setting Table

High Blood Level Med. Blood Level Low Blood Level No Blood

DIP Sw. Coinage Disk Coinage. ‘oin

USA1GertFri
USA2Ger2Fre
USA3-Ger3Fr

USA4 — Gerd Fr4 USAECA GerECA FrECA USA USA10 Free Play Free Play Free Play SEQQoeag

One Counter Two Counters

Game Mode Test Mode

  • Indicates Factory Setting.
Page 17

CPU Board Test Select the CPU Board Test with either joystick then press any button to start the automatic test. When this test is activated, a “rug" pattern appears on the screen. When the rug pattern ends, Test O.K. or Test Failed appears on the screen. This test returns to the Diagnostic Menu automatically.

Sound Board Test This test allows the operator to listen to some of the sounds this game is capable of producing.

Use either joystick to select the test, then press any button to open the test menu. The screen displays two test options. Use either joystick to select an option and press any button to begin the test.

SOUND TEST MENU

GENERAL TEST analyzes the sound circuitry. The screen shows a list of error codes. A successful test causes a single "tone" to sound. Detection of a fault causes a Series of tones or no tone at all to sound. Press any button to return to the Sound Test Menu.

PLAY SOUNDS test synthesized and digitized sounds from the CPU/Sound Board. Advance to the next sound with any button. Use either joystick to end the test.

Select RETURN TO MAIN MENU or BACK TO DIAGNOSTIC MENU and press any button.

Page 18

Monitor Patterns The Monitor Patterns Test provides a menu for testing the monitor.

Select the test with either joystick. Press any button to open the test menu. Once the Monitor Patterns Test menu is open, use either joystick to select an option, and any button to begin it.

MONITOR PATTERNS MENU

The RED, GREEN and BLUE SCREEN tests {ill the screen with either red, green or blue. Press any button to return to the Monitor Patterns Menu.

The COLOR BARS test fills the screen with several shades of colors to help with red, green and blue level adjustments. Each color should appear sharp and clear. Press any button to return to the Monitor Patterns Menu.

The CROSSHATCH PATTERNS tesi fills the screen with a grid and a series of dots. The grid and the dots should be clear. The dots should be round. Press any button to return to the Monitor Patterns Menu.

\f any of the Monitor Patterns Test shows a need for adjustment, use the proper knobs on the Monitor Controls Board.

Use either joystick to select RETURN TO MAIN MENU or BACK TO DIAGNOSTIC MENU, then press any button.

Page 19

Check Disk This test checks the hard disk drive.

Use either joystick to select the test, then press any button to activate it. Press any button to return to the Diagnostic Menu.

CHECK DISK SCREEN

Burn-in Test The Burn-in Test continually repeats the CPU Board Test. Use this test to find intermittent CPU Board problems.

Use either joystick to select the test, then press any button to activate it. When the Burn-in Test detects an error the test stops and an error message is displayed on the screen. To exit this test, switch the game off, then on again.

The Audit Table specifies the number of Burn-in cycles that have been successfully completed.

Page 20

COIN BOOKKEEPING The Coin Bookkeeping Table records the coin box totals and the game play counters.

Use either joystick to select the Coin Bookkeeping Menu, then press any button to open it.

To exit Coin Bookkeeping, use either joystick to select RETURN TO MAIN MENU and press any button.

COIN BOOKKEEPING MENU

Page 21

GAME AUDITS Use joystick to select the Game Audits Menu, then press any button to open it. Page through the available audits by selecting NEXT AUDIT PAGE or LAST AUDIT PAGE. Select RETURN TO MAIN MENU and press any button to exit Game Audits.

NOTE Game audits cannot be set. They can only be cleared.

AUDIT MENU - PAGE TWO

Page 22

Game Audits Continued.

LAST AUDIT. PAGE | RETURN TO MAIN MENU

‘AUDIT MENU - PAGE FIVE 1-19

Page 23

Game Audits Continued.

AUDIT MENU - PAGE SIX

AUDIT MENU - PAGE EIGHT 1-20

Page 24

Game Audits Continued.

AUDIT MENU - PAGE NINE

LAST AUDIT PA

RETURN TO MAIN

AUDIT MENU - PAGE ELEVEN 1-21

Page 25

Game Audits Continued...

AUDIT MENU - PAGE TWELVE

AUDIT MENU - PAGE THIRTEEN

1-22

Page 26

GAME ADJUSTMENTS The Game Adjustments allow the operator to customize the game.

Use either joystick to select the Game Adjustments Menu. Press any button to open the menu.

The Game Adjustments Menu offers several options. Each option has several choices. Use either joystick to select an option, then press any button to open the option. The next menu screen provides a setting value. Use either joystick to change the setting value and press any button to lock it in.

To exit the Adjustments Menu, use either joystick to select RETURN TO MAIN MENU, then press any button.

NOTE Adjustment values set by DIP SWITCH, override adjustment values set by the menu system,

GAME ADJUSTMENTS MENU

Game Adjustments

Standard Pricing Standard pricing allow the operator to choose any of the “standard” selections from the Standard Pricing Table. See page 1-25.

Modify the setting value with either joystick. Press any button to lock in the new value and return to the Adjustments Menu.

Custom Pricing Custom pricing allows the operator to install pricing other than that of the Standard Pricing Table. Custom pricing also allows the operator to select the maximum amount of credits per game, the amount of credits required to start a game, and the amount of credits required to continue a game. This option is being adjusted from the DIP Switch settings. See page 1-26.

Modify the setting value with either joystick. Press any button to lock in a new value and return to the Adjustment Menu.

1-23

Page 27

Game Adjustments Continued...

Free Play This option selects free play. The setting choices for this adjustment are: -No

  • Yes
  • Factory Setting: No

Computer Difficulty This option determines how tough the computer opponents are. The setting choices for this adjustment are:

  • (1) Extra Easy
  • (2) Easy
  • (3) Medium
  • (4) Hard
  • (5) Extra Hard
  • Factory Setting: Medium

Winning Streak Reset This option determines the number of games that must be played before the high scores automatically reset to factory settings. The setting choice for this adjustment are:

  • No Reset
  • 5000 Games
  • 10,000 Games
  • 15,000 Games
  • Factory Setting: No Reset

1-24

Page 28

STANDARD PRICING TABLE

NameSetting - Credit/CoinCoin 1Coin 3Coin 2Coin4Bills
USA 11250{2 to Start; 2 to Continue)25¢25¢$1.00
USA 2125¢(2 to Start; 1 to Continue)25¢25¢$1.00
USA 31/25¢(1 to Start; 1 to Continue)25¢25e$1.00
USA 41/50¢, 3/$1.00 (1 to Start; 1 to Continue)25025¢$1.00
USA 51/50¢, 4/$1.00 (2 to Start; 1 to Continue)25¢25¢$1.00
USA 61/50¢(1 to Start; 1 to Continue)25¢25¢$1.00
usA71/50¢, 3/81.00 (1 to Start; 1 to Continue)25¢25¢$1,00
USAB1/50¢, 4/$1.00 (2 to Start; 2 to Continue)25¢25¢$1.00
USA1/25¢(3 to Start; 2 to Continue)25¢25¢$1.00
USA 101/25¢(3 to Start; 3 to Continue)25¢25¢$1.00
USA ECA1/25¢, 4/81.00 (2 10 Start; 2 to Continue)$1.0010¢25¢5e$1.00
German 1111M, 6/50M1DM50M
German 21/10M, 7/5DM1DM5DM
German 34/1DM, 8/SDM10M50M
German 41/1DM, 5/5DM1DM5DM
German §1/1DM, 6/SDM1DMSDM
German ECA4/1DM, 2/2DM, 6/50M50M1DM2DM
France 12USE, SINOFoF10F
France 2IF, A/10FSF10F
France 31USF, 3/10FSF10F
France 44S, 2/10FoF10F
France 52IBF, 5/10F, 11/2 x 10FSF10F
France 62ISF, ATOR, 9/2 x 10FSF10F
France 7AUSF, S/10F, 7/2 x 10F5F10F
France 81/5F, 2/10F, 5/2 x 10F5F10F
France 9113 x 1F, 25F1FSF
France 1012 x 1F, YSF1FoF
France 1113 x 1F, 2/5F, 5/2 x SF1FSF
France 121/2 x 16, S/5F, 7/2 x SF1FFE
France ECA113 x 16, 2/5F, 5/2 x 5F4F10F5F
Canada1/2 x 25¢, 3/$1.0025¢$1.00$1.00
Swiss 1ANF, 6/5F1FSF
Swiss 2AF, 715F1FoF
Swiss 3A/F, B/SF1FSF
Italy1/500 tire500 lire500 lire
UK 11/20P, /50P20P50P
UK22/20P, 5/S0P20P50P
UK ECA1/20P, 3/50P, 7/€1.00£1.0020P50P40P
UK Elec wiCCU1/30P, 2/50P, 4/£1.00£1.0020POP10P
‘Spain 11/100 peseta, 6/500 peseta100 peseta500 peseta
Spain 21/100 peseta, 5/500 peseta100 peseta500 peseta
Australia 113 x 20¢, 2/81.0020¢$1.00
Australia 21/5 x 20¢, 1/81.0020¢$1.00
Japan 11/100 yen100 yen100 yen
Japan 22/100 yen100 yen100 yen
Austria 11/8 schiling, 2/10 schilling5 chilling10 schilling
Austria 21/2 x § schilling, 9/2 x 10 schilling5 schilling10 schilling
Belgium 11/20F20F20F
Beigium 2320F20F20F
Belgium 3220F20F20F
Belgium ECA1/20FSOFSF20F
‘Sweden1/3 x 1 krona, 2/5 kronatkronaSkrona
New Zealand 113x 20¢20¢20¢
New Zealand 212 x 20¢20¢20¢
Netherlands1/1 HEI, 9/2.5 HFL1HFI2.5 HPI
Finland1/1 matkka1 markka1 markka
Norway4/2 x1 krone, 3/5 x 1 krone1 krone1 krone
Denmark1/2 x 1 krone, 3/5 krone, 7/2 x 5 krone1 kroneS krone
Antillies1/250, 4/1 quilder25¢4 guilder
Hungary1/2 x 10 forint, 9/2 x 20 forint10 forint20 forint

1-25

Page 29

(1)

(2)

(3)

(4)

(5)

(6)

(7) CUSTOM PRICING MENU

Coins inserted accumulate units. This adjustment specifies the number of units given for each coin in the fourth chute (see "units/credit").

This is the number of coin units required to buy one credit.

There is one bonus credit awarded after this many coin units have accumulated.

This is the minimum number of units required before any credits are awarded.

Each player needs this many credits to begin a game.

Each player needs this many credits to continue a game.

This is the limit for the credit counter. Additional coins inserted will be lost (factory setting: 30).

1-26

Page 30

UTILITIES The Utilities Menu allows the operator to clear the game's bookkeeping memory.

Use either joystick to select the Utilities Menu, then press any button.

UTILITIES MENU

Use either joystick to select a utility. Press any button to activate the selection. A dialogue box appears and the operator can choose to reset the utility. For example:

Use either joystick to choose a setting value. Press any button to lock in the new setting value.

To exit the Utilities Menu, use either joystick to select RETURN TO MAIN MENU, then press any button.

1-27

Page 31

VOLUME ADJUST The Volume Adjust feature allows the operator to determine the sound and music level of the game.

The volume level can be adjusted from either the Attract Mode or the Menu System. Press the Volume Up button to raise the volume level and the Volume Down button to lower the volume level. Either joystick can also be used to raise or low the volume level. The current volume level is shown with a red bar. Press the any button to return to the Main Menu.

VOLUME ADJUST PRESS ANY BUTTON TO EXIT

(MAXIMUM)

(CURRENT VOLUME LEVEL)

(MINIMUM)

1-28

Page 32

TROUBLESHOOTING

PROBLEM No picture or distorted picture.

Turn game On and nothing happens.

No sound.

Press start button and nothing happens.

No credit given for number of coins inserted.

Too many credits for number of coins inserted.

Game stay in test mode. POSSIBLE SOLUTION Check for faulty video board or monitor. Check for disconnected video signal cable.

Check line fuse. Check for +5Vdc at pins C, D, 3 and 4 of the JAMMA connector.

Check the speaker and the speaker connection to pin L and 10 on the JAMMA connector. Check volume control setting. Check for +12Vde at pins F and 6 on the JAMMA connector. Check for -5Vdc at pins E and 5 on the JAMMA connector.

Check for open wires between the button and the CPU board. Check for contamination on CPU board pins or the Start button switch blade contacts. Check for proper ground.

Check DIP switch coin settings. Check for contamination on the coin switch contacts. Check for an open wire between Coin Switch 1 and pin 16 on the JAMMA connector or Coin Switch 2 and pin T of the JAMMA connector.

Check the game pricing settings. Check for a short between pins T & 16 on the JAMMA connector.

Check that the switch #8 of DIP switch bank #2 is set to off.

1-29

Page 33

NOTES

1-30

Page 34

KILLER INSTINCT

KIT

SECTION two

Parts

Page 35

CPU/Sound Assembly A-19650-40047

DesignationPart NumberDescription
Ug98A-5343-40047-1Game EPROM
U10A-5343-40047-2Sound EPROM
ut1A-5343-40047-3Sound EPROM
u12A-5343-40047-4Sound EPROM
U13A-5343-40047-5Sound EPROM
U33A-5343-40047-6Sound EPROM
U34A-5343-40047-7Sound EPROM
U35A-5343-40047-8Sound EPROM
U36A-5343-40047-9Sound EPROM
$1, S25645-09025-00DIP Switch
J35791-12461-10Header, 10-pin
J65791-14457-00Header, 44-pin
J75791-12461-15Header, 15-pin
J85791-12461-08Header, 8-pin

use urs v6 ule | u35.

ut ue

d

JSAMMA i

Page 36

Hard Drive Mounting Bracket

im A-19595.1 Side View Front View

|*(o0]
PkLoOo}

Complete Hard Drive Assembly Diagram Ribbon Cable connector to J6 on CPU/Sound board

Ribbon Cable red ire—>| Ferrite Bead

Clip Clip Ferrite Bead VY, Clip

ee I | (Q) o)

Lk[O0}

Hard Drive Hard Drive Mounting Bracket

*LO|

2-3

Page 37

Fan 20-9947 Side View Front View

‘ | |p

OL SS °) — AC Connector

Fan Mounting Bracket

A-19806 ~ Ko) Ko) LONG SIDE

° L 5 | L | 0 s | ce

FRONT SHORT SIDE

Complete Fan Assembly Diagram

Fon Guard (plastic) NL a Fan Grille (metal)

h

Far Mounting Bracket

Fon

2-4

Page 38

KILLER INSTINCT

KIT

SECTION three

Wiring Diagrams

Page 39

JAMMA Chart

FUNCTION WIRE COLOR WIRE COLOR | FUNCTION Black Ground. Black Ground

Coin Counter 1 Coin Counter 2 | Brown-Red N/C. Speaker- Brown-Gray N/C Video Green Green Video Sync White Service Credits | White-Gray KO |00 IN I (7 | | Go [po

Red-Gray Speaker+ N/C Red Video Red Brown Video Blue

Shield Video Ground

Black-Blue Black-Brown White White-Black White-Brown White-Red White-Orange White-Yellow 1 Quick/High White-Green 1 Medium/High White-Blue 1 Fierce/High

White-Violet Not Used

N/C N/C Ground Black Ground

SOLDER SIDE COMPONENT SIDE Siam Tilt Black-Green Coin 2 Black-Red 2 Start Violet-White 2Up Violet-Black 2 Down Violet-Brown 2 Left Violet-Red 2 Right Violet-Orange 2 Quick/High Violet-Yellow 2 Medium/High }| Violet-Green ierce/High iolet-Blue Not Used TS) @ [2/0 (| IN/<)X<) S1<1 C/A) O) Dy OjZz/S\F AC [LIT |mMJojo|a|>

3-2

Page 40

41 NE G3SA LON

Interboard Wiring

COIN INTERLOCK. erciiNa ik ‘KEY En oRAVGE-GREEN SE Once RES z CPU/SOUND BOARD A-19650—40047 re LT 10

iH

222822 senenenn- | snentrine | berthed : : ioe Se

Bsa sils a ai

& i 45

NOT USED IN KIT

Page 41

Coin Switch and Meter Wiring

Option 1 COIN SWITCH 1 CT —— | +5V

COIN SWITCH 2 rol — METER

JAMMA PIN 16

GROUND JAMMA PIN 8 OO a

Option 2 COIN SWITCH 1 J AEN TE a asy

COIN COIN SWITCH 2 vA — _ JAMMA PIN T METER

GROUND JAMMA PIN 8

'! WRONG WAY !!

Do not connect the coin switches in this manner. This circuit is INCORRECT and will cause twice as many credits per coin.

COIN SWITCH 1 pe AMMA PIN 16

COIN SWITCH 2 i

< = AMMA PIN T

| GROUND

Page 42

CPU BOARD

Cabinet Wiring

ae (CONTROL PANEL, CABLE

HI

SHELDED VIDEO CABLE ToL Ne

2acrown;
— are)3 oH Bxye=

(“ig a a

$ Ofer geoest4
3 Otwar one — re$
§Owe——F guieg wg8S
3Owe canwep er

er 9 OL WEL BU 1 FeRcA\Ge 9 ‘ool —Ne tox

wasua.

ToL Ne tas Fy cai

ont5Ogup

+ Sino" Ba? bom 3 OL Wo RZ 3 two pee 7 ear ro wo aes

igenwep\cr——$
9 Sf Wo BPsence——§

x Ovo wer ART

7 Ne

a29]SU aK 1 oucd\ion __g
1 $aahen tow —"§

5 x $l | __ iu ee ee ee uy GaN 2 WOU.

$ome?rence tow8

tool to

(2k BRN CON 1 uC RED CON

neo ay Fors Fav TO POWER SUPPLY MONTIOR waite sync

MONTIOR ‘BOARD NC [SHieto GROUND BROWN ViDEO BLUE loREEN VIDEO GREEN [RED WDE RED

TO HARD DISK

Page 43

Electronic Rack Assembly

E10 vowron a

ase -! {2

—— nn) vie, are

{sse" 38-00

& &

wan vanes z Eonar} 3 r

=| “ates

oO > EGa SRR eo coe

ONG we % ron © 6%

Ang senars NI

Ae Powe CALE Pome (oss al eras oe Q

LOCATE HARD DISC DRIVE MOUNTING BRACKET 10 BE PARALLEL WITH CORRESPONDING CPU RIBBON CABLE HEADER

OSS OF

RACK (WOOD ONLY) 11-1128 aes

GUL OF MATERIAL uns perso | vaGOrS HT He a eas oo!

3-6

Page 44

oN \ \ \ —— 1625 —,

0.813 a a \ a “oO / / /

3.000

Page 45

1.281 2.562

~ LL)

3.000 rs < ~~

1.500 TS 0.813 \ > —— 1.625 —~

< N“N

@) NORD

(Ania

3.250

Page 46

CONTROL PANEL WIRE COLORS

Player One

Start White

Up White-Black Down White-Brown

Left White-Red Right White-Orange

Quick/High White-Yellow Medium/High White-Green Fierce/High White-Blue Quick/Low —_ Blue-Black Medium/Low Blue-Brown Fierce/Low Blue-Red

Ground Black

Player Two

Start Violet-White

Up Violet-Black Down Violet-Brown

Left Violet-Red

Right Violet-Orange

Quick/High Violet-Yellow Medium/High Violet-Green Fierce/High Violet-Blue Quick/Low __ Blue-Yellow Medium/Low Blue-Green Fierce/Low Blue

Page 47

WARNING & NOTICES

WARNING USE OF NON-MIDWAY PARTS OR CIRCUIT MODIFICATIONS MAY CAUSE SERIOUS INJURY OR EQUIP- MENT DAMAGE! USE ONLY MIDWAY AUTHORIZED PARTS.
  • For safety and reliability, substitute parts and modifications are not recommended.
  • Substitute parts or modifications may void FCC type acceptance.
  • This game is protected by federal copyright, trademark and patent laws. Unauthorized modifications may be illegal under federal law. This also applies to MIDWAY logos, designs, publications and assemblies. Moreover, facsimiles of MIDWAY equipment (or any feature thereof) may be illegal under federal law, regardless of whether or not such facsimiles are manufactured with MIDWAY components.
WARNING
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, Pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generated, uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
WARNING Prevent shock hazard and assure proper game operation. Only plug this game into a properly grounded outlet. Do not use a cheater plug to defeat the power cord’s grounding pin. Do not cut off the ground pin.

NOTICE - FCC WARNING STICKER |. THIS KIT WAS TESTED IN A MIDWAY UNIVERSAL VIDEO CABINET AND FOUND TO COMPLY WITH FCC PART 15 CLASS A REQUIREMENTS. _ IF INSTALLED IN MIDWAY UNIVERSAL VIDEO CABINET, THE FCC WARNING STICKER (16-9306) SUPPLIED IS TO BE PLACED ON THE REAR OF THE CABINET. Il. INSTALLATION OF THIS KIT INTO ANY OTHER PRODUCT DOES NOT GUARANTY COMPLIANCE WITH FCC REQUIREMENTS. YOU ARE SOLELY RESPONSIBLE, AND MIDWAY WILL HAVE NO RESPONSIBILITY, FOR FCC COMPLIANCE FOR IN- STALLATIONS IN OTHER PRODUCTS. THE FCC WARNING STICKER SUPPLIED SHOULD NOT BE INSTALLED ON THE CONVERTED PRODUCT UNTIL FCC COM- PLIANCE IS VERIFIED.

NOTICE No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may be transmitted, or otherwise copied for public or private use, without permission from the publisher.

FOR SERVICE: CALL YOUR AUTHORIZED MIDWAY DISTRIBUTOR.

Killer Ingtinct™ © 1994 Nintendo/Rare Game by Rare Killer Instinct is a trademark of Nintendo Manufactured and sold by Midway Manufacturing Company under license

MIDWAY MANUFACTURING COMPANY 3401 N. CALIFORNIA AVE. CHICAGO, IL 60618