CATHODE RAY TOMES

Star Wars ST-225 1st Printing Backdoor Sheet

Star Wars (set 1) (Atari, 1983) · Backdoor Sheet · 1 pages · original scan

Page 1

Coin Counter Volume Control

Auxiliary Coin Switch

‘Sound Board

C

oO o OFF C on

oer ( ma 10 (> a

Switch Locations

Switch Settings for Play Options

Settings of 8-Toggle Switch on Star Wars Game PCB (at 10D)

12347

Option

On On

Off On Off Off Off On Off Off

On Off off off

On On Off Qn On Off

On On

On Off

On Off

On Off 6 Starting Shields 7 Starting Shields 8 Starting Shields 9 Starting Shields

Easy game play Moderate game play-4 Hard game play Hardest game play

0 Bonus Shields for Destroying Death Star 1 Bonus Shield for Destroying Death Star<¢ 2 Bonus Shields for Destroying Death Star 3 Bonus Shields for Destroying Death Star

Music in the Attract Mode<4 No Music in the Attract Mode

Freeze Mode Normal Game Play Mode<4

Switch Settings for Coin and Credit Options

Settings of 8-Toggle Switch on Star Wars Game PCB (at 10E/F)

12345678

Option

On On

On Off

On Off

On On

On off

On On

On Off

On On

On Off

Free Play 2 Credits 1 Credit % Credit

Left Coin Mechanism 1 Coin< 2 Coins

Right Coin Mechanism 1 Coin 4 Coins 5 Coins 6 Coins

Bonus Coin Adder 0 Bonus Coins Added 1 Bonus Coin Added for 2 Coins 1 Bonus Coin Added for 4 Coins 2 Bonus Coins Added for 4 Coins 1 Bonus Coin Added for 5 Coins 1 Bonus Coin Added for 3 Coins 0 Bonus Coins Added 0 Bonus Coins Added

Switch Settings for Special Options

Settings of 4-Toggle Switch on Star Wars Game PCB (at IIL)

23Option
OnFazZzOutputs of coin counter driver | and 2 tied together
ece(for 1 counter)
offaagOutputs of coin counter driver 1 and 2 separate (for 2

counters)

{Manufacturer's recommended settings

Self-Test Procedure

This game will test itself and provide data to show that the game circuitry and control are operating properly. Selftest data is presented visually on the video display. No additional equipment is required We suggest you perform a self-test when you first set up, each time you collect money, when you change the game options, or.when you suspect game failure.

Self-Test Displays

Fourteen self-test displays provide a visual check of the game statistics, options, switch settings, mathbox circuitry, display circuitry, and the condition of the readonly memory (ROM) and random-access memory (RAM). The first self-test display (Size and Centering) is obtained in the Attract Mode. When the'self-test switch is turned on during the Attract Mode, the game enters the Self-Test Mode. Turning the self-test switch off during the Self-Test Mode returns the game to the Attract Mode,

NOTE Before selecting the Self-Test Mode and with the game in the Attract Mode, check that a small blue dotis displayed within % -inch of the edge in each. corner of the screen. The remaining self-test displays are obtained while the gameis in the Self-Test Mode.
NOTE ‘The following self-test displays are arranged in the sequence in which they occur after the self-test switch is set to the on position. Press the auxiliary coin switch to end each display and obtain the next display. Pressing the auxiliary coin switch will advance through the displays. After the last display has ended, the sequence starts over with the Switch ‘Test display. To start with the Accounting and Game Times display, the self-test switch must first be turned off and then on again.

Accounting and Game Times Display Enter the Self-Test Mode by pushing the self-test switch to the up position. The Accounting and Game Times display will appear first. The totals on this display are those accumulated since the accounting and game times information was last reset. (Refer to Game Options Display for the reset procedure.) The coin accounting information, which is the first four statistics in the Accounting Information section of the display, cannot be reset. They are accumulated from the date the game was manufactured, or since the NOVRAM last failed or was replaced.

ACCOUNTING INFORMATION de

HTETORY OF GAME ort suvy

s.4n @Ux EOIN TH CONTINUE

Accounting and Game Times Display

Game Options Display Press the auxiliary coin switch to obtain the Game Options display. Use this display to view or change game option settings; reset high scores; reset accounting and game time information; or test the NOVRAM.

DeTIONS tteen rr

PLAY DIFFICULTY BONUS SHIELD MUSEC IN @TTRACT HOE RATE

TEST NOVRAM = NEN EAenng PULL RIGHT FIRE TO PERFORM RESETS uP, DOWN TO SELECT ETEn PULL LEFT PERE TO CHeNRE SCTTINT PRESS @Ux COIN FOR SELF TEST

Game Options Display The first section of the Game Options display shows the option settings that have been selected by either the opdon switches on the Main PCB or by the flight control. The second section of the Game Options display shows the reset and NOVRAM test operations that are selectable with the flight control. Press the auxiliary coin switch to end this display. Changing the Game Options. Any of the options displayed in the first section of the Game Options display can be changed without setting the option switches on the Main PCB. Select the option tobe changed by moving the flight'control up or down. Press the left-hand fire trigger to cycle through the available options as indicated in the right-hand column; stop op the desired option setting. The changed optiégt Js immediately stored in the NOVRAM and is unaffected by turning off the power or the self-test switch. The options can also be changed to those selectéd by the option switches located on the Main PCB. If the self-test circuitry malfunctions or the option settings €annot be maintained by the software, the game will defavyt to the hardware Switch settings on the Main PCB (refét to Resettirigthe Options for more details). Resetting the High Scores. The top ten scores and player initials are displayed in the high-score table during the Attract Mode, All high scores.can be yeset using the Game Options display. Select RESET HIGH SCORES by moving the flight control up or down. Press the left-hand fire triggerand note that YES appears.in the right-hand column. Then press the right-hand fire trigger to perform the reset operation, which is completed when NO appears in the right-hand column, Resetting the Timing Information. The games played and the timing information in the Accounting and Game Times display can be reset using the Game Options display. Select RESET TIMING INFO by moving the flight control up or down. Press the left-hand fire trigger and

note that YES appears in the right-hand column. Then press the right-hand fire ttiggbr to. perform the reset operation, which :is completed when NO appears in the right-hand column. Resetting the Options. The option settings shown on the Game Options display can be'reset (defaulted) to those selected by the option’switches located on the Main PCB. Select RESET OPTIQNS by moving the flight control up or down. Press the left*hand fire trigger and note that YES ~ppears in the right-hand column: Then press the righthand fire trigger to perform the reset operation, which is completed when NO appears in the right-hand column. ‘Testing the NOVRAM. The NOVRAM can be tested using the Game Options display. Select TEST NOVRAM by moving the flight control up or down. Press the left-hand trigger and check that NO ERRORS appears in the righthand column. Ifthe NOVRAM is defective, a message ER- ROR AT anda hexadecimal number will appear which indicates that the NOVRAM should be replaced. Testing the NOVRAM should only be performed ifa defective part is suspected because each, test decreases the life of the NOVRAM.

Hardware Errors Display Press the auxiliary coin switch and wait about seven seconds to obtain the Hardware Errors display. This display shows the condition of the game RAM and ROM. If no hardware errors exist, the message NO ERRORS DETECT: EDwillbe displayed. If there isa RAM or ROM failure, the display will identify the failed component and give its location.

Switch Test Display Press the auxiliaty coin switch to obtain the Switch Test display. Perform the following procedure to verify that the game switches are operating properly:

  • Oneatatime, press the fire triggers and thumb pushbuttons. Note that a message appears on the display that indicates which switch was pressed.
  • Actuate the right and left coin mechanisms and note that a message appears that indicates which coin mechanism was actuated. Position the flight control to forma single dot in the center of the smallest box in the POT TEST portion of the display. Carefully release the flight control and note that the dot remains centered within the smallest box. Ifa line forms that extends outside the frame of the smallest box, the flight control potentiometers may be misaligned.
  • Tiltthe flight control handles forward and backward;
note that line forms from the center of the smallest box and moves out and back in relation to the handle position. Tilt the handles to the extreme forward and backward position; note that the line extends past the frame of the box with open corners but not beyond the frame of the largest box,
  • Turn the flight control fully clockwise and counterclockwise with the handles at the extreme forward then backward positions. Note that the line travels over a full 360° while not extending outside the area between the largest box and the box with the open corners. *
  • Verify. that the option settings for the switches at location 10D and 10E/F shownat the bottom center of the display match those selected on the corresponding option switches (F= off, N=on) 87-225 1st printing

Mathbox Tests Display Press the auxiliary coin switch to obtain the Mathbox Tests display. The first test verifies that the MATHBOX READY signal is operating normally. If it is not, the message BAD MATHBOX READY LINE appears and no further mathbox tests are performed. If the MATHBOX READY signal is correct, then the divider and matrix circuitry should be tested. If no problems exist in the divider or matrix circuitry, the messages NO DIVIDER ERRORS and NO MATRIX ERRORS are displayed. If divider errors exist, the message DIVIDER ERRORS will appear and each error will be indicated with an option-switch setting for the corresponding diagnostic. Also, the numbers used on the test with the expected answer and the incorrect answer received will be displayed for each test in error. If matrix errors exist, the message MATRIX ERRORS will appear with the corresponding option switch settings for the diagnostic. Some matrix errors do not have a corresponding diagnostic. In this case, there will be no optionswitch setting.

Crosshatch Pattern Display Press the auxiliary coin switch to obtain the Crosshatch Pattern display. Verify that the corners are closed and the diagonal lines form symmetrical diamond-shaped squares, that all four corners of the border are completely visible and are within 4 -inch from the black edge of the screen, that the pattern is not tilted more than % -inch between corners, and that the pattern is a uniform green color. Ifany of the preceding characteristics are not correct, refer to the linearity adjustment procedure in the Analog Vector-Generator schematic diagrams.

Grid Pattern Display Press the auxiliary coin switch to obtain a Grid Pattern display. Check that the grid colors advance through the order of red, green, blue, purple, white, yellow, and turquoise each time the fire trigger is pressed. Check that the grid lines do not exhibit pincushioning or barreling and the lines are straight within %-inch. Check that the convergence does not exceed 2.0 mm, as checked with the white grid. Ifany of the preceding display characteristics are not correct, refer to the linearity adjustment procedure in the Analog Vector-Generator schematic diagrams and to the convergence adjustment procedure in the Display Manual.

Intensity Test Display Press the auxiliary coin switch to obtain the Intensity Test display. Check that the top row of color bars are red, blue, and green. Check thatall three sets of color bars have six lines with the same intensity, and that the bars underneath the top row are white, yellow, turquoise, and purple. The words DIM, LOW, and HIGH appear in the bottom center of the display. If the word OFF can be seen, the display is too bright. If the word LOW cannot be seen, the display is not bright enough

Bipolar Offset Test Display Press the auxiliary coin switch to obtain the Bipolar Offset Test TEST display. The line width should be 4-inch or less. If not, adjust the X/Y bipolar offset potentiometers located in the digital-to-analog converter and bipolar current sources circuit on the Analog Vector-Generator PCB.

Scale Test Display Press the auxiliary coin switch to obtain the Scale Test Linear display. A large green square should appear in the center of the screen and then smoothly shrink to a point. Next, a large green SCALE TEST LINEAR AND BINARY square appears and shrinks smoothly, then pauses and continues to shrink. There should be eight pauses before the square shrinks to a point. After each pause and just when the square begins to shrink, the size of the square should not change appreciably. Ifa large change in the size of the square occurs, an error may exist. After the eighth pause, the sequence repeats with the Scale Test Linear and Binary display.

Important Note to Operators: If the operators manual was not included in this game when you unpacked it, contact your distributor to get a free copy. (All Atari manuals for coinoperated games also include complete illustrated Parts lists.)

ATART (© A Warner communications Company

*Trademarks of Lucasfilm, Ltd. used by Atari, Inc. under license.